1#
2# Freescale device configuration
3#
4
5config NET_VENDOR_FREESCALE
6	bool "Freescale devices"
7	default y
8	depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
9		   M523x || M527x || M5272 || M528x || M520x || M532x || \
10		   ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM)
11	---help---
12	  If you have a network (Ethernet) card belonging to this class, say Y
13	  and read the Ethernet-HOWTO, available from
14	  <http://www.tldp.org/docs.html#howto>.
15
16	  Note that the answer to this question doesn't directly affect the
17	  kernel: saying N will just cause the configurator to skip all
18	  the questions about Freescale devices. If you say Y, you will be
19	  asked for your specific card in the following questions.
20
21if NET_VENDOR_FREESCALE
22
23config FEC
24	tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
25	depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
26		   ARCH_MXC || SOC_IMX28)
27	default ARCH_MXC || SOC_IMX28 if ARM
28	select PHYLIB
29	select PTP_1588_CLOCK
30	---help---
31	  Say Y here if you want to use the built-in 10/100 Fast ethernet
32	  controller on some Motorola ColdFire and Freescale i.MX processors.
33
34config FEC_MPC52xx
35	tristate "FEC MPC52xx driver"
36	depends on PPC_MPC52xx && PPC_BESTCOMM
37	select CRC32
38	select PHYLIB
39	select PPC_BESTCOMM_FEC
40	---help---
41	  This option enables support for the MPC5200's on-chip
42	  Fast Ethernet Controller
43	  If compiled as module, it will be called fec_mpc52xx.
44
45config FEC_MPC52xx_MDIO
46	bool "FEC MPC52xx MDIO bus driver"
47	depends on FEC_MPC52xx
48	default y
49	---help---
50	  The MPC5200's FEC can connect to the Ethernet either with
51	  an external MII PHY chip or 10 Mbps 7-wire interface
52	  (Motorola? industry standard).
53	  If your board uses an external PHY connected to FEC, enable this.
54	  If not sure, enable.
55	  If compiled as module, it will be called fec_mpc52xx_phy.
56
57source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
58
59config FSL_PQ_MDIO
60	tristate "Freescale PQ MDIO"
61	depends on FSL_SOC
62	select PHYLIB
63	---help---
64	  This driver supports the MDIO bus used by the gianfar and UCC drivers.
65
66config FSL_XGMAC_MDIO
67	tristate "Freescale XGMAC MDIO"
68	depends on FSL_SOC
69	select PHYLIB
70	---help---
71	  This driver supports the MDIO bus on the Fman 10G Ethernet MACs.
72
73config UCC_GETH
74	tristate "Freescale QE Gigabit Ethernet"
75	depends on QUICC_ENGINE
76	select FSL_PQ_MDIO
77	select PHYLIB
78	---help---
79	  This driver supports the Gigabit Ethernet mode of the QUICC Engine,
80	  which is available on some Freescale SOCs.
81
82config UGETH_TX_ON_DEMAND
83	bool "Transmit on Demand support"
84	depends on UCC_GETH
85
86config GIANFAR
87	tristate "Gianfar Ethernet"
88	depends on FSL_SOC
89	select FSL_PQ_MDIO
90	select PHYLIB
91	select CRC32
92	---help---
93	  This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
94	  and MPC86xx family of chips, and the FEC on the 8540.
95
96endif # NET_VENDOR_FREESCALE
97