1 /* 2 * Davicom DM9000 Fast Ethernet driver for Linux. 3 * Copyright (C) 1997 Sten Wang 4 * 5 * This program is free software; you can redistribute it and/or 6 * modify it under the terms of the GNU General Public License 7 * as published by the Free Software Foundation; either version 2 8 * of the License, or (at your option) any later version. 9 * 10 * This program is distributed in the hope that it will be useful, 11 * but WITHOUT ANY WARRANTY; without even the implied warranty of 12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 13 * GNU General Public License for more details. 14 * 15 * (C) Copyright 1997-1998 DAVICOM Semiconductor,Inc. All Rights Reserved. 16 * 17 * Additional updates, Copyright: 18 * Ben Dooks <ben@simtec.co.uk> 19 * Sascha Hauer <s.hauer@pengutronix.de> 20 */ 21 22 #include <linux/module.h> 23 #include <linux/ioport.h> 24 #include <linux/netdevice.h> 25 #include <linux/etherdevice.h> 26 #include <linux/interrupt.h> 27 #include <linux/skbuff.h> 28 #include <linux/spinlock.h> 29 #include <linux/crc32.h> 30 #include <linux/mii.h> 31 #include <linux/of.h> 32 #include <linux/of_net.h> 33 #include <linux/ethtool.h> 34 #include <linux/dm9000.h> 35 #include <linux/delay.h> 36 #include <linux/platform_device.h> 37 #include <linux/irq.h> 38 #include <linux/slab.h> 39 #include <linux/regulator/consumer.h> 40 #include <linux/gpio.h> 41 #include <linux/of_gpio.h> 42 43 #include <asm/delay.h> 44 #include <asm/irq.h> 45 #include <asm/io.h> 46 47 #include "dm9000.h" 48 49 /* Board/System/Debug information/definition ---------------- */ 50 51 #define DM9000_PHY 0x40 /* PHY address 0x01 */ 52 53 #define CARDNAME "dm9000" 54 #define DRV_VERSION "1.31" 55 56 /* 57 * Transmit timeout, default 5 seconds. 58 */ 59 static int watchdog = 5000; 60 module_param(watchdog, int, 0400); 61 MODULE_PARM_DESC(watchdog, "transmit timeout in milliseconds"); 62 63 /* 64 * Debug messages level 65 */ 66 static int debug; 67 module_param(debug, int, 0644); 68 MODULE_PARM_DESC(debug, "dm9000 debug level (0-6)"); 69 70 /* DM9000 register address locking. 71 * 72 * The DM9000 uses an address register to control where data written 73 * to the data register goes. This means that the address register 74 * must be preserved over interrupts or similar calls. 75 * 76 * During interrupt and other critical calls, a spinlock is used to 77 * protect the system, but the calls themselves save the address 78 * in the address register in case they are interrupting another 79 * access to the device. 80 * 81 * For general accesses a lock is provided so that calls which are 82 * allowed to sleep are serialised so that the address register does 83 * not need to be saved. This lock also serves to serialise access 84 * to the EEPROM and PHY access registers which are shared between 85 * these two devices. 86 */ 87 88 /* The driver supports the original DM9000E, and now the two newer 89 * devices, DM9000A and DM9000B. 90 */ 91 92 enum dm9000_type { 93 TYPE_DM9000E, /* original DM9000 */ 94 TYPE_DM9000A, 95 TYPE_DM9000B 96 }; 97 98 /* Structure/enum declaration ------------------------------- */ 99 struct board_info { 100 101 void __iomem *io_addr; /* Register I/O base address */ 102 void __iomem *io_data; /* Data I/O address */ 103 u16 irq; /* IRQ */ 104 105 u16 tx_pkt_cnt; 106 u16 queue_pkt_len; 107 u16 queue_start_addr; 108 u16 queue_ip_summed; 109 u16 dbug_cnt; 110 u8 io_mode; /* 0:word, 2:byte */ 111 u8 phy_addr; 112 u8 imr_all; 113 114 unsigned int flags; 115 unsigned int in_timeout:1; 116 unsigned int in_suspend:1; 117 unsigned int wake_supported:1; 118 119 enum dm9000_type type; 120 121 void (*inblk)(void __iomem *port, void *data, int length); 122 void (*outblk)(void __iomem *port, void *data, int length); 123 void (*dumpblk)(void __iomem *port, int length); 124 125 struct device *dev; /* parent device */ 126 127 struct resource *addr_res; /* resources found */ 128 struct resource *data_res; 129 struct resource *addr_req; /* resources requested */ 130 struct resource *data_req; 131 132 int irq_wake; 133 134 struct mutex addr_lock; /* phy and eeprom access lock */ 135 136 struct delayed_work phy_poll; 137 struct net_device *ndev; 138 139 spinlock_t lock; 140 141 struct mii_if_info mii; 142 u32 msg_enable; 143 u32 wake_state; 144 145 int ip_summed; 146 }; 147 148 /* debug code */ 149 150 #define dm9000_dbg(db, lev, msg...) do { \ 151 if ((lev) < debug) { \ 152 dev_dbg(db->dev, msg); \ 153 } \ 154 } while (0) 155 156 static inline struct board_info *to_dm9000_board(struct net_device *dev) 157 { 158 return netdev_priv(dev); 159 } 160 161 /* DM9000 network board routine ---------------------------- */ 162 163 /* 164 * Read a byte from I/O port 165 */ 166 static u8 167 ior(struct board_info *db, int reg) 168 { 169 writeb(reg, db->io_addr); 170 return readb(db->io_data); 171 } 172 173 /* 174 * Write a byte to I/O port 175 */ 176 177 static void 178 iow(struct board_info *db, int reg, int value) 179 { 180 writeb(reg, db->io_addr); 181 writeb(value, db->io_data); 182 } 183 184 static void 185 dm9000_reset(struct board_info *db) 186 { 187 dev_dbg(db->dev, "resetting device\n"); 188 189 /* Reset DM9000, see DM9000 Application Notes V1.22 Jun 11, 2004 page 29 190 * The essential point is that we have to do a double reset, and the 191 * instruction is to set LBK into MAC internal loopback mode. 192 */ 193 iow(db, DM9000_NCR, NCR_RST | NCR_MAC_LBK); 194 udelay(100); /* Application note says at least 20 us */ 195 if (ior(db, DM9000_NCR) & 1) 196 dev_err(db->dev, "dm9000 did not respond to first reset\n"); 197 198 iow(db, DM9000_NCR, 0); 199 iow(db, DM9000_NCR, NCR_RST | NCR_MAC_LBK); 200 udelay(100); 201 if (ior(db, DM9000_NCR) & 1) 202 dev_err(db->dev, "dm9000 did not respond to second reset\n"); 203 } 204 205 /* routines for sending block to chip */ 206 207 static void dm9000_outblk_8bit(void __iomem *reg, void *data, int count) 208 { 209 iowrite8_rep(reg, data, count); 210 } 211 212 static void dm9000_outblk_16bit(void __iomem *reg, void *data, int count) 213 { 214 iowrite16_rep(reg, data, (count+1) >> 1); 215 } 216 217 static void dm9000_outblk_32bit(void __iomem *reg, void *data, int count) 218 { 219 iowrite32_rep(reg, data, (count+3) >> 2); 220 } 221 222 /* input block from chip to memory */ 223 224 static void dm9000_inblk_8bit(void __iomem *reg, void *data, int count) 225 { 226 ioread8_rep(reg, data, count); 227 } 228 229 230 static void dm9000_inblk_16bit(void __iomem *reg, void *data, int count) 231 { 232 ioread16_rep(reg, data, (count+1) >> 1); 233 } 234 235 static void dm9000_inblk_32bit(void __iomem *reg, void *data, int count) 236 { 237 ioread32_rep(reg, data, (count+3) >> 2); 238 } 239 240 /* dump block from chip to null */ 241 242 static void dm9000_dumpblk_8bit(void __iomem *reg, int count) 243 { 244 int i; 245 int tmp; 246 247 for (i = 0; i < count; i++) 248 tmp = readb(reg); 249 } 250 251 static void dm9000_dumpblk_16bit(void __iomem *reg, int count) 252 { 253 int i; 254 int tmp; 255 256 count = (count + 1) >> 1; 257 258 for (i = 0; i < count; i++) 259 tmp = readw(reg); 260 } 261 262 static void dm9000_dumpblk_32bit(void __iomem *reg, int count) 263 { 264 int i; 265 int tmp; 266 267 count = (count + 3) >> 2; 268 269 for (i = 0; i < count; i++) 270 tmp = readl(reg); 271 } 272 273 /* 274 * Sleep, either by using msleep() or if we are suspending, then 275 * use mdelay() to sleep. 276 */ 277 static void dm9000_msleep(struct board_info *db, unsigned int ms) 278 { 279 if (db->in_suspend || db->in_timeout) 280 mdelay(ms); 281 else 282 msleep(ms); 283 } 284 285 /* Read a word from phyxcer */ 286 static int 287 dm9000_phy_read(struct net_device *dev, int phy_reg_unused, int reg) 288 { 289 struct board_info *db = netdev_priv(dev); 290 unsigned long flags; 291 unsigned int reg_save; 292 int ret; 293 294 mutex_lock(&db->addr_lock); 295 296 spin_lock_irqsave(&db->lock, flags); 297 298 /* Save previous register address */ 299 reg_save = readb(db->io_addr); 300 301 /* Fill the phyxcer register into REG_0C */ 302 iow(db, DM9000_EPAR, DM9000_PHY | reg); 303 304 /* Issue phyxcer read command */ 305 iow(db, DM9000_EPCR, EPCR_ERPRR | EPCR_EPOS); 306 307 writeb(reg_save, db->io_addr); 308 spin_unlock_irqrestore(&db->lock, flags); 309 310 dm9000_msleep(db, 1); /* Wait read complete */ 311 312 spin_lock_irqsave(&db->lock, flags); 313 reg_save = readb(db->io_addr); 314 315 iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer read command */ 316 317 /* The read data keeps on REG_0D & REG_0E */ 318 ret = (ior(db, DM9000_EPDRH) << 8) | ior(db, DM9000_EPDRL); 319 320 /* restore the previous address */ 321 writeb(reg_save, db->io_addr); 322 spin_unlock_irqrestore(&db->lock, flags); 323 324 mutex_unlock(&db->addr_lock); 325 326 dm9000_dbg(db, 5, "phy_read[%02x] -> %04x\n", reg, ret); 327 return ret; 328 } 329 330 /* Write a word to phyxcer */ 331 static void 332 dm9000_phy_write(struct net_device *dev, 333 int phyaddr_unused, int reg, int value) 334 { 335 struct board_info *db = netdev_priv(dev); 336 unsigned long flags; 337 unsigned long reg_save; 338 339 dm9000_dbg(db, 5, "phy_write[%02x] = %04x\n", reg, value); 340 if (!db->in_timeout) 341 mutex_lock(&db->addr_lock); 342 343 spin_lock_irqsave(&db->lock, flags); 344 345 /* Save previous register address */ 346 reg_save = readb(db->io_addr); 347 348 /* Fill the phyxcer register into REG_0C */ 349 iow(db, DM9000_EPAR, DM9000_PHY | reg); 350 351 /* Fill the written data into REG_0D & REG_0E */ 352 iow(db, DM9000_EPDRL, value); 353 iow(db, DM9000_EPDRH, value >> 8); 354 355 /* Issue phyxcer write command */ 356 iow(db, DM9000_EPCR, EPCR_EPOS | EPCR_ERPRW); 357 358 writeb(reg_save, db->io_addr); 359 spin_unlock_irqrestore(&db->lock, flags); 360 361 dm9000_msleep(db, 1); /* Wait write complete */ 362 363 spin_lock_irqsave(&db->lock, flags); 364 reg_save = readb(db->io_addr); 365 366 iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer write command */ 367 368 /* restore the previous address */ 369 writeb(reg_save, db->io_addr); 370 371 spin_unlock_irqrestore(&db->lock, flags); 372 if (!db->in_timeout) 373 mutex_unlock(&db->addr_lock); 374 } 375 376 /* dm9000_set_io 377 * 378 * select the specified set of io routines to use with the 379 * device 380 */ 381 382 static void dm9000_set_io(struct board_info *db, int byte_width) 383 { 384 /* use the size of the data resource to work out what IO 385 * routines we want to use 386 */ 387 388 switch (byte_width) { 389 case 1: 390 db->dumpblk = dm9000_dumpblk_8bit; 391 db->outblk = dm9000_outblk_8bit; 392 db->inblk = dm9000_inblk_8bit; 393 break; 394 395 396 case 3: 397 dev_dbg(db->dev, ": 3 byte IO, falling back to 16bit\n"); 398 /* fall through */ 399 case 2: 400 db->dumpblk = dm9000_dumpblk_16bit; 401 db->outblk = dm9000_outblk_16bit; 402 db->inblk = dm9000_inblk_16bit; 403 break; 404 405 case 4: 406 default: 407 db->dumpblk = dm9000_dumpblk_32bit; 408 db->outblk = dm9000_outblk_32bit; 409 db->inblk = dm9000_inblk_32bit; 410 break; 411 } 412 } 413 414 static void dm9000_schedule_poll(struct board_info *db) 415 { 416 if (db->type == TYPE_DM9000E) 417 schedule_delayed_work(&db->phy_poll, HZ * 2); 418 } 419 420 static int dm9000_ioctl(struct net_device *dev, struct ifreq *req, int cmd) 421 { 422 struct board_info *dm = to_dm9000_board(dev); 423 424 if (!netif_running(dev)) 425 return -EINVAL; 426 427 return generic_mii_ioctl(&dm->mii, if_mii(req), cmd, NULL); 428 } 429 430 static unsigned int 431 dm9000_read_locked(struct board_info *db, int reg) 432 { 433 unsigned long flags; 434 unsigned int ret; 435 436 spin_lock_irqsave(&db->lock, flags); 437 ret = ior(db, reg); 438 spin_unlock_irqrestore(&db->lock, flags); 439 440 return ret; 441 } 442 443 static int dm9000_wait_eeprom(struct board_info *db) 444 { 445 unsigned int status; 446 int timeout = 8; /* wait max 8msec */ 447 448 /* The DM9000 data sheets say we should be able to 449 * poll the ERRE bit in EPCR to wait for the EEPROM 450 * operation. From testing several chips, this bit 451 * does not seem to work. 452 * 453 * We attempt to use the bit, but fall back to the 454 * timeout (which is why we do not return an error 455 * on expiry) to say that the EEPROM operation has 456 * completed. 457 */ 458 459 while (1) { 460 status = dm9000_read_locked(db, DM9000_EPCR); 461 462 if ((status & EPCR_ERRE) == 0) 463 break; 464 465 msleep(1); 466 467 if (timeout-- < 0) { 468 dev_dbg(db->dev, "timeout waiting EEPROM\n"); 469 break; 470 } 471 } 472 473 return 0; 474 } 475 476 /* 477 * Read a word data from EEPROM 478 */ 479 static void 480 dm9000_read_eeprom(struct board_info *db, int offset, u8 *to) 481 { 482 unsigned long flags; 483 484 if (db->flags & DM9000_PLATF_NO_EEPROM) { 485 to[0] = 0xff; 486 to[1] = 0xff; 487 return; 488 } 489 490 mutex_lock(&db->addr_lock); 491 492 spin_lock_irqsave(&db->lock, flags); 493 494 iow(db, DM9000_EPAR, offset); 495 iow(db, DM9000_EPCR, EPCR_ERPRR); 496 497 spin_unlock_irqrestore(&db->lock, flags); 498 499 dm9000_wait_eeprom(db); 500 501 /* delay for at-least 150uS */ 502 msleep(1); 503 504 spin_lock_irqsave(&db->lock, flags); 505 506 iow(db, DM9000_EPCR, 0x0); 507 508 to[0] = ior(db, DM9000_EPDRL); 509 to[1] = ior(db, DM9000_EPDRH); 510 511 spin_unlock_irqrestore(&db->lock, flags); 512 513 mutex_unlock(&db->addr_lock); 514 } 515 516 /* 517 * Write a word data to SROM 518 */ 519 static void 520 dm9000_write_eeprom(struct board_info *db, int offset, u8 *data) 521 { 522 unsigned long flags; 523 524 if (db->flags & DM9000_PLATF_NO_EEPROM) 525 return; 526 527 mutex_lock(&db->addr_lock); 528 529 spin_lock_irqsave(&db->lock, flags); 530 iow(db, DM9000_EPAR, offset); 531 iow(db, DM9000_EPDRH, data[1]); 532 iow(db, DM9000_EPDRL, data[0]); 533 iow(db, DM9000_EPCR, EPCR_WEP | EPCR_ERPRW); 534 spin_unlock_irqrestore(&db->lock, flags); 535 536 dm9000_wait_eeprom(db); 537 538 mdelay(1); /* wait at least 150uS to clear */ 539 540 spin_lock_irqsave(&db->lock, flags); 541 iow(db, DM9000_EPCR, 0); 542 spin_unlock_irqrestore(&db->lock, flags); 543 544 mutex_unlock(&db->addr_lock); 545 } 546 547 /* ethtool ops */ 548 549 static void dm9000_get_drvinfo(struct net_device *dev, 550 struct ethtool_drvinfo *info) 551 { 552 struct board_info *dm = to_dm9000_board(dev); 553 554 strlcpy(info->driver, CARDNAME, sizeof(info->driver)); 555 strlcpy(info->version, DRV_VERSION, sizeof(info->version)); 556 strlcpy(info->bus_info, to_platform_device(dm->dev)->name, 557 sizeof(info->bus_info)); 558 } 559 560 static u32 dm9000_get_msglevel(struct net_device *dev) 561 { 562 struct board_info *dm = to_dm9000_board(dev); 563 564 return dm->msg_enable; 565 } 566 567 static void dm9000_set_msglevel(struct net_device *dev, u32 value) 568 { 569 struct board_info *dm = to_dm9000_board(dev); 570 571 dm->msg_enable = value; 572 } 573 574 static int dm9000_get_link_ksettings(struct net_device *dev, 575 struct ethtool_link_ksettings *cmd) 576 { 577 struct board_info *dm = to_dm9000_board(dev); 578 579 mii_ethtool_get_link_ksettings(&dm->mii, cmd); 580 return 0; 581 } 582 583 static int dm9000_set_link_ksettings(struct net_device *dev, 584 const struct ethtool_link_ksettings *cmd) 585 { 586 struct board_info *dm = to_dm9000_board(dev); 587 588 return mii_ethtool_set_link_ksettings(&dm->mii, cmd); 589 } 590 591 static int dm9000_nway_reset(struct net_device *dev) 592 { 593 struct board_info *dm = to_dm9000_board(dev); 594 return mii_nway_restart(&dm->mii); 595 } 596 597 static int dm9000_set_features(struct net_device *dev, 598 netdev_features_t features) 599 { 600 struct board_info *dm = to_dm9000_board(dev); 601 netdev_features_t changed = dev->features ^ features; 602 unsigned long flags; 603 604 if (!(changed & NETIF_F_RXCSUM)) 605 return 0; 606 607 spin_lock_irqsave(&dm->lock, flags); 608 iow(dm, DM9000_RCSR, (features & NETIF_F_RXCSUM) ? RCSR_CSUM : 0); 609 spin_unlock_irqrestore(&dm->lock, flags); 610 611 return 0; 612 } 613 614 static u32 dm9000_get_link(struct net_device *dev) 615 { 616 struct board_info *dm = to_dm9000_board(dev); 617 u32 ret; 618 619 if (dm->flags & DM9000_PLATF_EXT_PHY) 620 ret = mii_link_ok(&dm->mii); 621 else 622 ret = dm9000_read_locked(dm, DM9000_NSR) & NSR_LINKST ? 1 : 0; 623 624 return ret; 625 } 626 627 #define DM_EEPROM_MAGIC (0x444D394B) 628 629 static int dm9000_get_eeprom_len(struct net_device *dev) 630 { 631 return 128; 632 } 633 634 static int dm9000_get_eeprom(struct net_device *dev, 635 struct ethtool_eeprom *ee, u8 *data) 636 { 637 struct board_info *dm = to_dm9000_board(dev); 638 int offset = ee->offset; 639 int len = ee->len; 640 int i; 641 642 /* EEPROM access is aligned to two bytes */ 643 644 if ((len & 1) != 0 || (offset & 1) != 0) 645 return -EINVAL; 646 647 if (dm->flags & DM9000_PLATF_NO_EEPROM) 648 return -ENOENT; 649 650 ee->magic = DM_EEPROM_MAGIC; 651 652 for (i = 0; i < len; i += 2) 653 dm9000_read_eeprom(dm, (offset + i) / 2, data + i); 654 655 return 0; 656 } 657 658 static int dm9000_set_eeprom(struct net_device *dev, 659 struct ethtool_eeprom *ee, u8 *data) 660 { 661 struct board_info *dm = to_dm9000_board(dev); 662 int offset = ee->offset; 663 int len = ee->len; 664 int done; 665 666 /* EEPROM access is aligned to two bytes */ 667 668 if (dm->flags & DM9000_PLATF_NO_EEPROM) 669 return -ENOENT; 670 671 if (ee->magic != DM_EEPROM_MAGIC) 672 return -EINVAL; 673 674 while (len > 0) { 675 if (len & 1 || offset & 1) { 676 int which = offset & 1; 677 u8 tmp[2]; 678 679 dm9000_read_eeprom(dm, offset / 2, tmp); 680 tmp[which] = *data; 681 dm9000_write_eeprom(dm, offset / 2, tmp); 682 683 done = 1; 684 } else { 685 dm9000_write_eeprom(dm, offset / 2, data); 686 done = 2; 687 } 688 689 data += done; 690 offset += done; 691 len -= done; 692 } 693 694 return 0; 695 } 696 697 static void dm9000_get_wol(struct net_device *dev, struct ethtool_wolinfo *w) 698 { 699 struct board_info *dm = to_dm9000_board(dev); 700 701 memset(w, 0, sizeof(struct ethtool_wolinfo)); 702 703 /* note, we could probably support wake-phy too */ 704 w->supported = dm->wake_supported ? WAKE_MAGIC : 0; 705 w->wolopts = dm->wake_state; 706 } 707 708 static int dm9000_set_wol(struct net_device *dev, struct ethtool_wolinfo *w) 709 { 710 struct board_info *dm = to_dm9000_board(dev); 711 unsigned long flags; 712 u32 opts = w->wolopts; 713 u32 wcr = 0; 714 715 if (!dm->wake_supported) 716 return -EOPNOTSUPP; 717 718 if (opts & ~WAKE_MAGIC) 719 return -EINVAL; 720 721 if (opts & WAKE_MAGIC) 722 wcr |= WCR_MAGICEN; 723 724 mutex_lock(&dm->addr_lock); 725 726 spin_lock_irqsave(&dm->lock, flags); 727 iow(dm, DM9000_WCR, wcr); 728 spin_unlock_irqrestore(&dm->lock, flags); 729 730 mutex_unlock(&dm->addr_lock); 731 732 if (dm->wake_state != opts) { 733 /* change in wol state, update IRQ state */ 734 735 if (!dm->wake_state) 736 irq_set_irq_wake(dm->irq_wake, 1); 737 else if (dm->wake_state && !opts) 738 irq_set_irq_wake(dm->irq_wake, 0); 739 } 740 741 dm->wake_state = opts; 742 return 0; 743 } 744 745 static const struct ethtool_ops dm9000_ethtool_ops = { 746 .get_drvinfo = dm9000_get_drvinfo, 747 .get_msglevel = dm9000_get_msglevel, 748 .set_msglevel = dm9000_set_msglevel, 749 .nway_reset = dm9000_nway_reset, 750 .get_link = dm9000_get_link, 751 .get_wol = dm9000_get_wol, 752 .set_wol = dm9000_set_wol, 753 .get_eeprom_len = dm9000_get_eeprom_len, 754 .get_eeprom = dm9000_get_eeprom, 755 .set_eeprom = dm9000_set_eeprom, 756 .get_link_ksettings = dm9000_get_link_ksettings, 757 .set_link_ksettings = dm9000_set_link_ksettings, 758 }; 759 760 static void dm9000_show_carrier(struct board_info *db, 761 unsigned carrier, unsigned nsr) 762 { 763 int lpa; 764 struct net_device *ndev = db->ndev; 765 struct mii_if_info *mii = &db->mii; 766 unsigned ncr = dm9000_read_locked(db, DM9000_NCR); 767 768 if (carrier) { 769 lpa = mii->mdio_read(mii->dev, mii->phy_id, MII_LPA); 770 dev_info(db->dev, 771 "%s: link up, %dMbps, %s-duplex, lpa 0x%04X\n", 772 ndev->name, (nsr & NSR_SPEED) ? 10 : 100, 773 (ncr & NCR_FDX) ? "full" : "half", lpa); 774 } else { 775 dev_info(db->dev, "%s: link down\n", ndev->name); 776 } 777 } 778 779 static void 780 dm9000_poll_work(struct work_struct *w) 781 { 782 struct delayed_work *dw = to_delayed_work(w); 783 struct board_info *db = container_of(dw, struct board_info, phy_poll); 784 struct net_device *ndev = db->ndev; 785 786 if (db->flags & DM9000_PLATF_SIMPLE_PHY && 787 !(db->flags & DM9000_PLATF_EXT_PHY)) { 788 unsigned nsr = dm9000_read_locked(db, DM9000_NSR); 789 unsigned old_carrier = netif_carrier_ok(ndev) ? 1 : 0; 790 unsigned new_carrier; 791 792 new_carrier = (nsr & NSR_LINKST) ? 1 : 0; 793 794 if (old_carrier != new_carrier) { 795 if (netif_msg_link(db)) 796 dm9000_show_carrier(db, new_carrier, nsr); 797 798 if (!new_carrier) 799 netif_carrier_off(ndev); 800 else 801 netif_carrier_on(ndev); 802 } 803 } else 804 mii_check_media(&db->mii, netif_msg_link(db), 0); 805 806 if (netif_running(ndev)) 807 dm9000_schedule_poll(db); 808 } 809 810 /* dm9000_release_board 811 * 812 * release a board, and any mapped resources 813 */ 814 815 static void 816 dm9000_release_board(struct platform_device *pdev, struct board_info *db) 817 { 818 /* unmap our resources */ 819 820 iounmap(db->io_addr); 821 iounmap(db->io_data); 822 823 /* release the resources */ 824 825 if (db->data_req) 826 release_resource(db->data_req); 827 kfree(db->data_req); 828 829 if (db->addr_req) 830 release_resource(db->addr_req); 831 kfree(db->addr_req); 832 } 833 834 static unsigned char dm9000_type_to_char(enum dm9000_type type) 835 { 836 switch (type) { 837 case TYPE_DM9000E: return 'e'; 838 case TYPE_DM9000A: return 'a'; 839 case TYPE_DM9000B: return 'b'; 840 } 841 842 return '?'; 843 } 844 845 /* 846 * Set DM9000 multicast address 847 */ 848 static void 849 dm9000_hash_table_unlocked(struct net_device *dev) 850 { 851 struct board_info *db = netdev_priv(dev); 852 struct netdev_hw_addr *ha; 853 int i, oft; 854 u32 hash_val; 855 u16 hash_table[4] = { 0, 0, 0, 0x8000 }; /* broadcast address */ 856 u8 rcr = RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN; 857 858 dm9000_dbg(db, 1, "entering %s\n", __func__); 859 860 for (i = 0, oft = DM9000_PAR; i < 6; i++, oft++) 861 iow(db, oft, dev->dev_addr[i]); 862 863 if (dev->flags & IFF_PROMISC) 864 rcr |= RCR_PRMSC; 865 866 if (dev->flags & IFF_ALLMULTI) 867 rcr |= RCR_ALL; 868 869 /* the multicast address in Hash Table : 64 bits */ 870 netdev_for_each_mc_addr(ha, dev) { 871 hash_val = ether_crc_le(6, ha->addr) & 0x3f; 872 hash_table[hash_val / 16] |= (u16) 1 << (hash_val % 16); 873 } 874 875 /* Write the hash table to MAC MD table */ 876 for (i = 0, oft = DM9000_MAR; i < 4; i++) { 877 iow(db, oft++, hash_table[i]); 878 iow(db, oft++, hash_table[i] >> 8); 879 } 880 881 iow(db, DM9000_RCR, rcr); 882 } 883 884 static void 885 dm9000_hash_table(struct net_device *dev) 886 { 887 struct board_info *db = netdev_priv(dev); 888 unsigned long flags; 889 890 spin_lock_irqsave(&db->lock, flags); 891 dm9000_hash_table_unlocked(dev); 892 spin_unlock_irqrestore(&db->lock, flags); 893 } 894 895 static void 896 dm9000_mask_interrupts(struct board_info *db) 897 { 898 iow(db, DM9000_IMR, IMR_PAR); 899 } 900 901 static void 902 dm9000_unmask_interrupts(struct board_info *db) 903 { 904 iow(db, DM9000_IMR, db->imr_all); 905 } 906 907 /* 908 * Initialize dm9000 board 909 */ 910 static void 911 dm9000_init_dm9000(struct net_device *dev) 912 { 913 struct board_info *db = netdev_priv(dev); 914 unsigned int imr; 915 unsigned int ncr; 916 917 dm9000_dbg(db, 1, "entering %s\n", __func__); 918 919 dm9000_reset(db); 920 dm9000_mask_interrupts(db); 921 922 /* I/O mode */ 923 db->io_mode = ior(db, DM9000_ISR) >> 6; /* ISR bit7:6 keeps I/O mode */ 924 925 /* Checksum mode */ 926 if (dev->hw_features & NETIF_F_RXCSUM) 927 iow(db, DM9000_RCSR, 928 (dev->features & NETIF_F_RXCSUM) ? RCSR_CSUM : 0); 929 930 iow(db, DM9000_GPCR, GPCR_GEP_CNTL); /* Let GPIO0 output */ 931 iow(db, DM9000_GPR, 0); 932 933 /* If we are dealing with DM9000B, some extra steps are required: a 934 * manual phy reset, and setting init params. 935 */ 936 if (db->type == TYPE_DM9000B) { 937 dm9000_phy_write(dev, 0, MII_BMCR, BMCR_RESET); 938 dm9000_phy_write(dev, 0, MII_DM_DSPCR, DSPCR_INIT_PARAM); 939 } 940 941 ncr = (db->flags & DM9000_PLATF_EXT_PHY) ? NCR_EXT_PHY : 0; 942 943 /* if wol is needed, then always set NCR_WAKEEN otherwise we end 944 * up dumping the wake events if we disable this. There is already 945 * a wake-mask in DM9000_WCR */ 946 if (db->wake_supported) 947 ncr |= NCR_WAKEEN; 948 949 iow(db, DM9000_NCR, ncr); 950 951 /* Program operating register */ 952 iow(db, DM9000_TCR, 0); /* TX Polling clear */ 953 iow(db, DM9000_BPTR, 0x3f); /* Less 3Kb, 200us */ 954 iow(db, DM9000_FCR, 0xff); /* Flow Control */ 955 iow(db, DM9000_SMCR, 0); /* Special Mode */ 956 /* clear TX status */ 957 iow(db, DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END); 958 iow(db, DM9000_ISR, ISR_CLR_STATUS); /* Clear interrupt status */ 959 960 /* Set address filter table */ 961 dm9000_hash_table_unlocked(dev); 962 963 imr = IMR_PAR | IMR_PTM | IMR_PRM; 964 if (db->type != TYPE_DM9000E) 965 imr |= IMR_LNKCHNG; 966 967 db->imr_all = imr; 968 969 /* Init Driver variable */ 970 db->tx_pkt_cnt = 0; 971 db->queue_pkt_len = 0; 972 netif_trans_update(dev); 973 } 974 975 /* Our watchdog timed out. Called by the networking layer */ 976 static void dm9000_timeout(struct net_device *dev) 977 { 978 struct board_info *db = netdev_priv(dev); 979 u8 reg_save; 980 unsigned long flags; 981 982 /* Save previous register address */ 983 spin_lock_irqsave(&db->lock, flags); 984 db->in_timeout = 1; 985 reg_save = readb(db->io_addr); 986 987 netif_stop_queue(dev); 988 dm9000_init_dm9000(dev); 989 dm9000_unmask_interrupts(db); 990 /* We can accept TX packets again */ 991 netif_trans_update(dev); /* prevent tx timeout */ 992 netif_wake_queue(dev); 993 994 /* Restore previous register address */ 995 writeb(reg_save, db->io_addr); 996 db->in_timeout = 0; 997 spin_unlock_irqrestore(&db->lock, flags); 998 } 999 1000 static void dm9000_send_packet(struct net_device *dev, 1001 int ip_summed, 1002 u16 pkt_len) 1003 { 1004 struct board_info *dm = to_dm9000_board(dev); 1005 1006 /* The DM9000 is not smart enough to leave fragmented packets alone. */ 1007 if (dm->ip_summed != ip_summed) { 1008 if (ip_summed == CHECKSUM_NONE) 1009 iow(dm, DM9000_TCCR, 0); 1010 else 1011 iow(dm, DM9000_TCCR, TCCR_IP | TCCR_UDP | TCCR_TCP); 1012 dm->ip_summed = ip_summed; 1013 } 1014 1015 /* Set TX length to DM9000 */ 1016 iow(dm, DM9000_TXPLL, pkt_len); 1017 iow(dm, DM9000_TXPLH, pkt_len >> 8); 1018 1019 /* Issue TX polling command */ 1020 iow(dm, DM9000_TCR, TCR_TXREQ); /* Cleared after TX complete */ 1021 } 1022 1023 /* 1024 * Hardware start transmission. 1025 * Send a packet to media from the upper layer. 1026 */ 1027 static int 1028 dm9000_start_xmit(struct sk_buff *skb, struct net_device *dev) 1029 { 1030 unsigned long flags; 1031 struct board_info *db = netdev_priv(dev); 1032 1033 dm9000_dbg(db, 3, "%s:\n", __func__); 1034 1035 if (db->tx_pkt_cnt > 1) 1036 return NETDEV_TX_BUSY; 1037 1038 spin_lock_irqsave(&db->lock, flags); 1039 1040 /* Move data to DM9000 TX RAM */ 1041 writeb(DM9000_MWCMD, db->io_addr); 1042 1043 (db->outblk)(db->io_data, skb->data, skb->len); 1044 dev->stats.tx_bytes += skb->len; 1045 1046 db->tx_pkt_cnt++; 1047 /* TX control: First packet immediately send, second packet queue */ 1048 if (db->tx_pkt_cnt == 1) { 1049 dm9000_send_packet(dev, skb->ip_summed, skb->len); 1050 } else { 1051 /* Second packet */ 1052 db->queue_pkt_len = skb->len; 1053 db->queue_ip_summed = skb->ip_summed; 1054 netif_stop_queue(dev); 1055 } 1056 1057 spin_unlock_irqrestore(&db->lock, flags); 1058 1059 /* free this SKB */ 1060 dev_consume_skb_any(skb); 1061 1062 return NETDEV_TX_OK; 1063 } 1064 1065 /* 1066 * DM9000 interrupt handler 1067 * receive the packet to upper layer, free the transmitted packet 1068 */ 1069 1070 static void dm9000_tx_done(struct net_device *dev, struct board_info *db) 1071 { 1072 int tx_status = ior(db, DM9000_NSR); /* Got TX status */ 1073 1074 if (tx_status & (NSR_TX2END | NSR_TX1END)) { 1075 /* One packet sent complete */ 1076 db->tx_pkt_cnt--; 1077 dev->stats.tx_packets++; 1078 1079 if (netif_msg_tx_done(db)) 1080 dev_dbg(db->dev, "tx done, NSR %02x\n", tx_status); 1081 1082 /* Queue packet check & send */ 1083 if (db->tx_pkt_cnt > 0) 1084 dm9000_send_packet(dev, db->queue_ip_summed, 1085 db->queue_pkt_len); 1086 netif_wake_queue(dev); 1087 } 1088 } 1089 1090 struct dm9000_rxhdr { 1091 u8 RxPktReady; 1092 u8 RxStatus; 1093 __le16 RxLen; 1094 } __packed; 1095 1096 /* 1097 * Received a packet and pass to upper layer 1098 */ 1099 static void 1100 dm9000_rx(struct net_device *dev) 1101 { 1102 struct board_info *db = netdev_priv(dev); 1103 struct dm9000_rxhdr rxhdr; 1104 struct sk_buff *skb; 1105 u8 rxbyte, *rdptr; 1106 bool GoodPacket; 1107 int RxLen; 1108 1109 /* Check packet ready or not */ 1110 do { 1111 ior(db, DM9000_MRCMDX); /* Dummy read */ 1112 1113 /* Get most updated data */ 1114 rxbyte = readb(db->io_data); 1115 1116 /* Status check: this byte must be 0 or 1 */ 1117 if (rxbyte & DM9000_PKT_ERR) { 1118 dev_warn(db->dev, "status check fail: %d\n", rxbyte); 1119 iow(db, DM9000_RCR, 0x00); /* Stop Device */ 1120 return; 1121 } 1122 1123 if (!(rxbyte & DM9000_PKT_RDY)) 1124 return; 1125 1126 /* A packet ready now & Get status/length */ 1127 GoodPacket = true; 1128 writeb(DM9000_MRCMD, db->io_addr); 1129 1130 (db->inblk)(db->io_data, &rxhdr, sizeof(rxhdr)); 1131 1132 RxLen = le16_to_cpu(rxhdr.RxLen); 1133 1134 if (netif_msg_rx_status(db)) 1135 dev_dbg(db->dev, "RX: status %02x, length %04x\n", 1136 rxhdr.RxStatus, RxLen); 1137 1138 /* Packet Status check */ 1139 if (RxLen < 0x40) { 1140 GoodPacket = false; 1141 if (netif_msg_rx_err(db)) 1142 dev_dbg(db->dev, "RX: Bad Packet (runt)\n"); 1143 } 1144 1145 if (RxLen > DM9000_PKT_MAX) { 1146 dev_dbg(db->dev, "RST: RX Len:%x\n", RxLen); 1147 } 1148 1149 /* rxhdr.RxStatus is identical to RSR register. */ 1150 if (rxhdr.RxStatus & (RSR_FOE | RSR_CE | RSR_AE | 1151 RSR_PLE | RSR_RWTO | 1152 RSR_LCS | RSR_RF)) { 1153 GoodPacket = false; 1154 if (rxhdr.RxStatus & RSR_FOE) { 1155 if (netif_msg_rx_err(db)) 1156 dev_dbg(db->dev, "fifo error\n"); 1157 dev->stats.rx_fifo_errors++; 1158 } 1159 if (rxhdr.RxStatus & RSR_CE) { 1160 if (netif_msg_rx_err(db)) 1161 dev_dbg(db->dev, "crc error\n"); 1162 dev->stats.rx_crc_errors++; 1163 } 1164 if (rxhdr.RxStatus & RSR_RF) { 1165 if (netif_msg_rx_err(db)) 1166 dev_dbg(db->dev, "length error\n"); 1167 dev->stats.rx_length_errors++; 1168 } 1169 } 1170 1171 /* Move data from DM9000 */ 1172 if (GoodPacket && 1173 ((skb = netdev_alloc_skb(dev, RxLen + 4)) != NULL)) { 1174 skb_reserve(skb, 2); 1175 rdptr = skb_put(skb, RxLen - 4); 1176 1177 /* Read received packet from RX SRAM */ 1178 1179 (db->inblk)(db->io_data, rdptr, RxLen); 1180 dev->stats.rx_bytes += RxLen; 1181 1182 /* Pass to upper layer */ 1183 skb->protocol = eth_type_trans(skb, dev); 1184 if (dev->features & NETIF_F_RXCSUM) { 1185 if ((((rxbyte & 0x1c) << 3) & rxbyte) == 0) 1186 skb->ip_summed = CHECKSUM_UNNECESSARY; 1187 else 1188 skb_checksum_none_assert(skb); 1189 } 1190 netif_rx(skb); 1191 dev->stats.rx_packets++; 1192 1193 } else { 1194 /* need to dump the packet's data */ 1195 1196 (db->dumpblk)(db->io_data, RxLen); 1197 } 1198 } while (rxbyte & DM9000_PKT_RDY); 1199 } 1200 1201 static irqreturn_t dm9000_interrupt(int irq, void *dev_id) 1202 { 1203 struct net_device *dev = dev_id; 1204 struct board_info *db = netdev_priv(dev); 1205 int int_status; 1206 unsigned long flags; 1207 u8 reg_save; 1208 1209 dm9000_dbg(db, 3, "entering %s\n", __func__); 1210 1211 /* A real interrupt coming */ 1212 1213 /* holders of db->lock must always block IRQs */ 1214 spin_lock_irqsave(&db->lock, flags); 1215 1216 /* Save previous register address */ 1217 reg_save = readb(db->io_addr); 1218 1219 dm9000_mask_interrupts(db); 1220 /* Got DM9000 interrupt status */ 1221 int_status = ior(db, DM9000_ISR); /* Got ISR */ 1222 iow(db, DM9000_ISR, int_status); /* Clear ISR status */ 1223 1224 if (netif_msg_intr(db)) 1225 dev_dbg(db->dev, "interrupt status %02x\n", int_status); 1226 1227 /* Received the coming packet */ 1228 if (int_status & ISR_PRS) 1229 dm9000_rx(dev); 1230 1231 /* Transmit Interrupt check */ 1232 if (int_status & ISR_PTS) 1233 dm9000_tx_done(dev, db); 1234 1235 if (db->type != TYPE_DM9000E) { 1236 if (int_status & ISR_LNKCHNG) { 1237 /* fire a link-change request */ 1238 schedule_delayed_work(&db->phy_poll, 1); 1239 } 1240 } 1241 1242 dm9000_unmask_interrupts(db); 1243 /* Restore previous register address */ 1244 writeb(reg_save, db->io_addr); 1245 1246 spin_unlock_irqrestore(&db->lock, flags); 1247 1248 return IRQ_HANDLED; 1249 } 1250 1251 static irqreturn_t dm9000_wol_interrupt(int irq, void *dev_id) 1252 { 1253 struct net_device *dev = dev_id; 1254 struct board_info *db = netdev_priv(dev); 1255 unsigned long flags; 1256 unsigned nsr, wcr; 1257 1258 spin_lock_irqsave(&db->lock, flags); 1259 1260 nsr = ior(db, DM9000_NSR); 1261 wcr = ior(db, DM9000_WCR); 1262 1263 dev_dbg(db->dev, "%s: NSR=0x%02x, WCR=0x%02x\n", __func__, nsr, wcr); 1264 1265 if (nsr & NSR_WAKEST) { 1266 /* clear, so we can avoid */ 1267 iow(db, DM9000_NSR, NSR_WAKEST); 1268 1269 if (wcr & WCR_LINKST) 1270 dev_info(db->dev, "wake by link status change\n"); 1271 if (wcr & WCR_SAMPLEST) 1272 dev_info(db->dev, "wake by sample packet\n"); 1273 if (wcr & WCR_MAGICST) 1274 dev_info(db->dev, "wake by magic packet\n"); 1275 if (!(wcr & (WCR_LINKST | WCR_SAMPLEST | WCR_MAGICST))) 1276 dev_err(db->dev, "wake signalled with no reason? " 1277 "NSR=0x%02x, WSR=0x%02x\n", nsr, wcr); 1278 } 1279 1280 spin_unlock_irqrestore(&db->lock, flags); 1281 1282 return (nsr & NSR_WAKEST) ? IRQ_HANDLED : IRQ_NONE; 1283 } 1284 1285 #ifdef CONFIG_NET_POLL_CONTROLLER 1286 /* 1287 *Used by netconsole 1288 */ 1289 static void dm9000_poll_controller(struct net_device *dev) 1290 { 1291 disable_irq(dev->irq); 1292 dm9000_interrupt(dev->irq, dev); 1293 enable_irq(dev->irq); 1294 } 1295 #endif 1296 1297 /* 1298 * Open the interface. 1299 * The interface is opened whenever "ifconfig" actives it. 1300 */ 1301 static int 1302 dm9000_open(struct net_device *dev) 1303 { 1304 struct board_info *db = netdev_priv(dev); 1305 unsigned int irq_flags = irq_get_trigger_type(dev->irq); 1306 1307 if (netif_msg_ifup(db)) 1308 dev_dbg(db->dev, "enabling %s\n", dev->name); 1309 1310 /* If there is no IRQ type specified, tell the user that this is a 1311 * problem 1312 */ 1313 if (irq_flags == IRQF_TRIGGER_NONE) 1314 dev_warn(db->dev, "WARNING: no IRQ resource flags set.\n"); 1315 1316 irq_flags |= IRQF_SHARED; 1317 1318 /* GPIO0 on pre-activate PHY, Reg 1F is not set by reset */ 1319 iow(db, DM9000_GPR, 0); /* REG_1F bit0 activate phyxcer */ 1320 mdelay(1); /* delay needs by DM9000B */ 1321 1322 /* Initialize DM9000 board */ 1323 dm9000_init_dm9000(dev); 1324 1325 if (request_irq(dev->irq, dm9000_interrupt, irq_flags, dev->name, dev)) 1326 return -EAGAIN; 1327 /* Now that we have an interrupt handler hooked up we can unmask 1328 * our interrupts 1329 */ 1330 dm9000_unmask_interrupts(db); 1331 1332 /* Init driver variable */ 1333 db->dbug_cnt = 0; 1334 1335 mii_check_media(&db->mii, netif_msg_link(db), 1); 1336 netif_start_queue(dev); 1337 1338 /* Poll initial link status */ 1339 schedule_delayed_work(&db->phy_poll, 1); 1340 1341 return 0; 1342 } 1343 1344 static void 1345 dm9000_shutdown(struct net_device *dev) 1346 { 1347 struct board_info *db = netdev_priv(dev); 1348 1349 /* RESET device */ 1350 dm9000_phy_write(dev, 0, MII_BMCR, BMCR_RESET); /* PHY RESET */ 1351 iow(db, DM9000_GPR, 0x01); /* Power-Down PHY */ 1352 dm9000_mask_interrupts(db); 1353 iow(db, DM9000_RCR, 0x00); /* Disable RX */ 1354 } 1355 1356 /* 1357 * Stop the interface. 1358 * The interface is stopped when it is brought. 1359 */ 1360 static int 1361 dm9000_stop(struct net_device *ndev) 1362 { 1363 struct board_info *db = netdev_priv(ndev); 1364 1365 if (netif_msg_ifdown(db)) 1366 dev_dbg(db->dev, "shutting down %s\n", ndev->name); 1367 1368 cancel_delayed_work_sync(&db->phy_poll); 1369 1370 netif_stop_queue(ndev); 1371 netif_carrier_off(ndev); 1372 1373 /* free interrupt */ 1374 free_irq(ndev->irq, ndev); 1375 1376 dm9000_shutdown(ndev); 1377 1378 return 0; 1379 } 1380 1381 static const struct net_device_ops dm9000_netdev_ops = { 1382 .ndo_open = dm9000_open, 1383 .ndo_stop = dm9000_stop, 1384 .ndo_start_xmit = dm9000_start_xmit, 1385 .ndo_tx_timeout = dm9000_timeout, 1386 .ndo_set_rx_mode = dm9000_hash_table, 1387 .ndo_do_ioctl = dm9000_ioctl, 1388 .ndo_set_features = dm9000_set_features, 1389 .ndo_validate_addr = eth_validate_addr, 1390 .ndo_set_mac_address = eth_mac_addr, 1391 #ifdef CONFIG_NET_POLL_CONTROLLER 1392 .ndo_poll_controller = dm9000_poll_controller, 1393 #endif 1394 }; 1395 1396 static struct dm9000_plat_data *dm9000_parse_dt(struct device *dev) 1397 { 1398 struct dm9000_plat_data *pdata; 1399 struct device_node *np = dev->of_node; 1400 const void *mac_addr; 1401 1402 if (!IS_ENABLED(CONFIG_OF) || !np) 1403 return ERR_PTR(-ENXIO); 1404 1405 pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); 1406 if (!pdata) 1407 return ERR_PTR(-ENOMEM); 1408 1409 if (of_find_property(np, "davicom,ext-phy", NULL)) 1410 pdata->flags |= DM9000_PLATF_EXT_PHY; 1411 if (of_find_property(np, "davicom,no-eeprom", NULL)) 1412 pdata->flags |= DM9000_PLATF_NO_EEPROM; 1413 1414 mac_addr = of_get_mac_address(np); 1415 if (mac_addr) 1416 memcpy(pdata->dev_addr, mac_addr, sizeof(pdata->dev_addr)); 1417 1418 return pdata; 1419 } 1420 1421 /* 1422 * Search DM9000 board, allocate space and register it 1423 */ 1424 static int 1425 dm9000_probe(struct platform_device *pdev) 1426 { 1427 struct dm9000_plat_data *pdata = dev_get_platdata(&pdev->dev); 1428 struct board_info *db; /* Point a board information structure */ 1429 struct net_device *ndev; 1430 struct device *dev = &pdev->dev; 1431 const unsigned char *mac_src; 1432 int ret = 0; 1433 int iosize; 1434 int i; 1435 u32 id_val; 1436 int reset_gpios; 1437 enum of_gpio_flags flags; 1438 struct regulator *power; 1439 bool inv_mac_addr = false; 1440 1441 power = devm_regulator_get(dev, "vcc"); 1442 if (IS_ERR(power)) { 1443 if (PTR_ERR(power) == -EPROBE_DEFER) 1444 return -EPROBE_DEFER; 1445 dev_dbg(dev, "no regulator provided\n"); 1446 } else { 1447 ret = regulator_enable(power); 1448 if (ret != 0) { 1449 dev_err(dev, 1450 "Failed to enable power regulator: %d\n", ret); 1451 return ret; 1452 } 1453 dev_dbg(dev, "regulator enabled\n"); 1454 } 1455 1456 reset_gpios = of_get_named_gpio_flags(dev->of_node, "reset-gpios", 0, 1457 &flags); 1458 if (gpio_is_valid(reset_gpios)) { 1459 ret = devm_gpio_request_one(dev, reset_gpios, flags, 1460 "dm9000_reset"); 1461 if (ret) { 1462 dev_err(dev, "failed to request reset gpio %d: %d\n", 1463 reset_gpios, ret); 1464 return -ENODEV; 1465 } 1466 1467 /* According to manual PWRST# Low Period Min 1ms */ 1468 msleep(2); 1469 gpio_set_value(reset_gpios, 1); 1470 /* Needs 3ms to read eeprom when PWRST is deasserted */ 1471 msleep(4); 1472 } 1473 1474 if (!pdata) { 1475 pdata = dm9000_parse_dt(&pdev->dev); 1476 if (IS_ERR(pdata)) 1477 return PTR_ERR(pdata); 1478 } 1479 1480 /* Init network device */ 1481 ndev = alloc_etherdev(sizeof(struct board_info)); 1482 if (!ndev) 1483 return -ENOMEM; 1484 1485 SET_NETDEV_DEV(ndev, &pdev->dev); 1486 1487 dev_dbg(&pdev->dev, "dm9000_probe()\n"); 1488 1489 /* setup board info structure */ 1490 db = netdev_priv(ndev); 1491 1492 db->dev = &pdev->dev; 1493 db->ndev = ndev; 1494 1495 spin_lock_init(&db->lock); 1496 mutex_init(&db->addr_lock); 1497 1498 INIT_DELAYED_WORK(&db->phy_poll, dm9000_poll_work); 1499 1500 db->addr_res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1501 db->data_res = platform_get_resource(pdev, IORESOURCE_MEM, 1); 1502 1503 if (!db->addr_res || !db->data_res) { 1504 dev_err(db->dev, "insufficient resources addr=%p data=%p\n", 1505 db->addr_res, db->data_res); 1506 ret = -ENOENT; 1507 goto out; 1508 } 1509 1510 ndev->irq = platform_get_irq(pdev, 0); 1511 if (ndev->irq < 0) { 1512 dev_err(db->dev, "interrupt resource unavailable: %d\n", 1513 ndev->irq); 1514 ret = ndev->irq; 1515 goto out; 1516 } 1517 1518 db->irq_wake = platform_get_irq(pdev, 1); 1519 if (db->irq_wake >= 0) { 1520 dev_dbg(db->dev, "wakeup irq %d\n", db->irq_wake); 1521 1522 ret = request_irq(db->irq_wake, dm9000_wol_interrupt, 1523 IRQF_SHARED, dev_name(db->dev), ndev); 1524 if (ret) { 1525 dev_err(db->dev, "cannot get wakeup irq (%d)\n", ret); 1526 } else { 1527 1528 /* test to see if irq is really wakeup capable */ 1529 ret = irq_set_irq_wake(db->irq_wake, 1); 1530 if (ret) { 1531 dev_err(db->dev, "irq %d cannot set wakeup (%d)\n", 1532 db->irq_wake, ret); 1533 ret = 0; 1534 } else { 1535 irq_set_irq_wake(db->irq_wake, 0); 1536 db->wake_supported = 1; 1537 } 1538 } 1539 } 1540 1541 iosize = resource_size(db->addr_res); 1542 db->addr_req = request_mem_region(db->addr_res->start, iosize, 1543 pdev->name); 1544 1545 if (db->addr_req == NULL) { 1546 dev_err(db->dev, "cannot claim address reg area\n"); 1547 ret = -EIO; 1548 goto out; 1549 } 1550 1551 db->io_addr = ioremap(db->addr_res->start, iosize); 1552 1553 if (db->io_addr == NULL) { 1554 dev_err(db->dev, "failed to ioremap address reg\n"); 1555 ret = -EINVAL; 1556 goto out; 1557 } 1558 1559 iosize = resource_size(db->data_res); 1560 db->data_req = request_mem_region(db->data_res->start, iosize, 1561 pdev->name); 1562 1563 if (db->data_req == NULL) { 1564 dev_err(db->dev, "cannot claim data reg area\n"); 1565 ret = -EIO; 1566 goto out; 1567 } 1568 1569 db->io_data = ioremap(db->data_res->start, iosize); 1570 1571 if (db->io_data == NULL) { 1572 dev_err(db->dev, "failed to ioremap data reg\n"); 1573 ret = -EINVAL; 1574 goto out; 1575 } 1576 1577 /* fill in parameters for net-dev structure */ 1578 ndev->base_addr = (unsigned long)db->io_addr; 1579 1580 /* ensure at least we have a default set of IO routines */ 1581 dm9000_set_io(db, iosize); 1582 1583 /* check to see if anything is being over-ridden */ 1584 if (pdata != NULL) { 1585 /* check to see if the driver wants to over-ride the 1586 * default IO width */ 1587 1588 if (pdata->flags & DM9000_PLATF_8BITONLY) 1589 dm9000_set_io(db, 1); 1590 1591 if (pdata->flags & DM9000_PLATF_16BITONLY) 1592 dm9000_set_io(db, 2); 1593 1594 if (pdata->flags & DM9000_PLATF_32BITONLY) 1595 dm9000_set_io(db, 4); 1596 1597 /* check to see if there are any IO routine 1598 * over-rides */ 1599 1600 if (pdata->inblk != NULL) 1601 db->inblk = pdata->inblk; 1602 1603 if (pdata->outblk != NULL) 1604 db->outblk = pdata->outblk; 1605 1606 if (pdata->dumpblk != NULL) 1607 db->dumpblk = pdata->dumpblk; 1608 1609 db->flags = pdata->flags; 1610 } 1611 1612 #ifdef CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL 1613 db->flags |= DM9000_PLATF_SIMPLE_PHY; 1614 #endif 1615 1616 dm9000_reset(db); 1617 1618 /* try multiple times, DM9000 sometimes gets the read wrong */ 1619 for (i = 0; i < 8; i++) { 1620 id_val = ior(db, DM9000_VIDL); 1621 id_val |= (u32)ior(db, DM9000_VIDH) << 8; 1622 id_val |= (u32)ior(db, DM9000_PIDL) << 16; 1623 id_val |= (u32)ior(db, DM9000_PIDH) << 24; 1624 1625 if (id_val == DM9000_ID) 1626 break; 1627 dev_err(db->dev, "read wrong id 0x%08x\n", id_val); 1628 } 1629 1630 if (id_val != DM9000_ID) { 1631 dev_err(db->dev, "wrong id: 0x%08x\n", id_val); 1632 ret = -ENODEV; 1633 goto out; 1634 } 1635 1636 /* Identify what type of DM9000 we are working on */ 1637 1638 id_val = ior(db, DM9000_CHIPR); 1639 dev_dbg(db->dev, "dm9000 revision 0x%02x\n", id_val); 1640 1641 switch (id_val) { 1642 case CHIPR_DM9000A: 1643 db->type = TYPE_DM9000A; 1644 break; 1645 case CHIPR_DM9000B: 1646 db->type = TYPE_DM9000B; 1647 break; 1648 default: 1649 dev_dbg(db->dev, "ID %02x => defaulting to DM9000E\n", id_val); 1650 db->type = TYPE_DM9000E; 1651 } 1652 1653 /* dm9000a/b are capable of hardware checksum offload */ 1654 if (db->type == TYPE_DM9000A || db->type == TYPE_DM9000B) { 1655 ndev->hw_features = NETIF_F_RXCSUM | NETIF_F_IP_CSUM; 1656 ndev->features |= ndev->hw_features; 1657 } 1658 1659 /* from this point we assume that we have found a DM9000 */ 1660 1661 ndev->netdev_ops = &dm9000_netdev_ops; 1662 ndev->watchdog_timeo = msecs_to_jiffies(watchdog); 1663 ndev->ethtool_ops = &dm9000_ethtool_ops; 1664 1665 db->msg_enable = NETIF_MSG_LINK; 1666 db->mii.phy_id_mask = 0x1f; 1667 db->mii.reg_num_mask = 0x1f; 1668 db->mii.force_media = 0; 1669 db->mii.full_duplex = 0; 1670 db->mii.dev = ndev; 1671 db->mii.mdio_read = dm9000_phy_read; 1672 db->mii.mdio_write = dm9000_phy_write; 1673 1674 mac_src = "eeprom"; 1675 1676 /* try reading the node address from the attached EEPROM */ 1677 for (i = 0; i < 6; i += 2) 1678 dm9000_read_eeprom(db, i / 2, ndev->dev_addr+i); 1679 1680 if (!is_valid_ether_addr(ndev->dev_addr) && pdata != NULL) { 1681 mac_src = "platform data"; 1682 memcpy(ndev->dev_addr, pdata->dev_addr, ETH_ALEN); 1683 } 1684 1685 if (!is_valid_ether_addr(ndev->dev_addr)) { 1686 /* try reading from mac */ 1687 1688 mac_src = "chip"; 1689 for (i = 0; i < 6; i++) 1690 ndev->dev_addr[i] = ior(db, i+DM9000_PAR); 1691 } 1692 1693 if (!is_valid_ether_addr(ndev->dev_addr)) { 1694 inv_mac_addr = true; 1695 eth_hw_addr_random(ndev); 1696 mac_src = "random"; 1697 } 1698 1699 1700 platform_set_drvdata(pdev, ndev); 1701 ret = register_netdev(ndev); 1702 1703 if (ret == 0) { 1704 if (inv_mac_addr) 1705 dev_warn(db->dev, "%s: Invalid ethernet MAC address. Please set using ip\n", 1706 ndev->name); 1707 printk(KERN_INFO "%s: dm9000%c at %p,%p IRQ %d MAC: %pM (%s)\n", 1708 ndev->name, dm9000_type_to_char(db->type), 1709 db->io_addr, db->io_data, ndev->irq, 1710 ndev->dev_addr, mac_src); 1711 } 1712 return 0; 1713 1714 out: 1715 dev_err(db->dev, "not found (%d).\n", ret); 1716 1717 dm9000_release_board(pdev, db); 1718 free_netdev(ndev); 1719 1720 return ret; 1721 } 1722 1723 static int 1724 dm9000_drv_suspend(struct device *dev) 1725 { 1726 struct net_device *ndev = dev_get_drvdata(dev); 1727 struct board_info *db; 1728 1729 if (ndev) { 1730 db = netdev_priv(ndev); 1731 db->in_suspend = 1; 1732 1733 if (!netif_running(ndev)) 1734 return 0; 1735 1736 netif_device_detach(ndev); 1737 1738 /* only shutdown if not using WoL */ 1739 if (!db->wake_state) 1740 dm9000_shutdown(ndev); 1741 } 1742 return 0; 1743 } 1744 1745 static int 1746 dm9000_drv_resume(struct device *dev) 1747 { 1748 struct net_device *ndev = dev_get_drvdata(dev); 1749 struct board_info *db = netdev_priv(ndev); 1750 1751 if (ndev) { 1752 if (netif_running(ndev)) { 1753 /* reset if we were not in wake mode to ensure if 1754 * the device was powered off it is in a known state */ 1755 if (!db->wake_state) { 1756 dm9000_init_dm9000(ndev); 1757 dm9000_unmask_interrupts(db); 1758 } 1759 1760 netif_device_attach(ndev); 1761 } 1762 1763 db->in_suspend = 0; 1764 } 1765 return 0; 1766 } 1767 1768 static const struct dev_pm_ops dm9000_drv_pm_ops = { 1769 .suspend = dm9000_drv_suspend, 1770 .resume = dm9000_drv_resume, 1771 }; 1772 1773 static int 1774 dm9000_drv_remove(struct platform_device *pdev) 1775 { 1776 struct net_device *ndev = platform_get_drvdata(pdev); 1777 1778 unregister_netdev(ndev); 1779 dm9000_release_board(pdev, netdev_priv(ndev)); 1780 free_netdev(ndev); /* free device structure */ 1781 1782 dev_dbg(&pdev->dev, "released and freed device\n"); 1783 return 0; 1784 } 1785 1786 #ifdef CONFIG_OF 1787 static const struct of_device_id dm9000_of_matches[] = { 1788 { .compatible = "davicom,dm9000", }, 1789 { /* sentinel */ } 1790 }; 1791 MODULE_DEVICE_TABLE(of, dm9000_of_matches); 1792 #endif 1793 1794 static struct platform_driver dm9000_driver = { 1795 .driver = { 1796 .name = "dm9000", 1797 .pm = &dm9000_drv_pm_ops, 1798 .of_match_table = of_match_ptr(dm9000_of_matches), 1799 }, 1800 .probe = dm9000_probe, 1801 .remove = dm9000_drv_remove, 1802 }; 1803 1804 module_platform_driver(dm9000_driver); 1805 1806 MODULE_AUTHOR("Sascha Hauer, Ben Dooks"); 1807 MODULE_DESCRIPTION("Davicom DM9000 network driver"); 1808 MODULE_LICENSE("GPL"); 1809 MODULE_ALIAS("platform:dm9000"); 1810