1 /* bnx2x_reg.h: Qlogic Everest network driver. 2 * 3 * Copyright (c) 2007-2013 Broadcom Corporation 4 * Copyright (c) 2014 QLogic Corporation 5 * All rights reserved 6 * 7 * This program is free software; you can redistribute it and/or modify 8 * it under the terms of the GNU General Public License as published by 9 * the Free Software Foundation. 10 * 11 * The registers description starts with the register Access type followed 12 * by size in bits. For example [RW 32]. The access types are: 13 * R - Read only 14 * RC - Clear on read 15 * RW - Read/Write 16 * ST - Statistics register (clear on read) 17 * W - Write only 18 * WB - Wide bus register - the size is over 32 bits and it should be 19 * read/write in consecutive 32 bits accesses 20 * WR - Write Clear (write 1 to clear the bit) 21 * 22 */ 23 #ifndef BNX2X_REG_H 24 #define BNX2X_REG_H 25 26 #define ATC_ATC_INT_STS_REG_ADDRESS_ERROR (0x1<<0) 27 #define ATC_ATC_INT_STS_REG_ATC_GPA_MULTIPLE_HITS (0x1<<2) 28 #define ATC_ATC_INT_STS_REG_ATC_IREQ_LESS_THAN_STU (0x1<<5) 29 #define ATC_ATC_INT_STS_REG_ATC_RCPL_TO_EMPTY_CNT (0x1<<3) 30 #define ATC_ATC_INT_STS_REG_ATC_TCPL_ERROR (0x1<<4) 31 #define ATC_ATC_INT_STS_REG_ATC_TCPL_TO_NOT_PEND (0x1<<1) 32 /* [RW 1] Initiate the ATC array - reset all the valid bits */ 33 #define ATC_REG_ATC_INIT_ARRAY 0x1100b8 34 /* [R 1] ATC initialization done */ 35 #define ATC_REG_ATC_INIT_DONE 0x1100bc 36 /* [RC 6] Interrupt register #0 read clear */ 37 #define ATC_REG_ATC_INT_STS_CLR 0x1101c0 38 /* [RW 5] Parity mask register #0 read/write */ 39 #define ATC_REG_ATC_PRTY_MASK 0x1101d8 40 /* [R 5] Parity register #0 read */ 41 #define ATC_REG_ATC_PRTY_STS 0x1101cc 42 /* [RC 5] Parity register #0 read clear */ 43 #define ATC_REG_ATC_PRTY_STS_CLR 0x1101d0 44 /* [RW 19] Interrupt mask register #0 read/write */ 45 #define BRB1_REG_BRB1_INT_MASK 0x60128 46 /* [R 19] Interrupt register #0 read */ 47 #define BRB1_REG_BRB1_INT_STS 0x6011c 48 /* [RW 4] Parity mask register #0 read/write */ 49 #define BRB1_REG_BRB1_PRTY_MASK 0x60138 50 /* [R 4] Parity register #0 read */ 51 #define BRB1_REG_BRB1_PRTY_STS 0x6012c 52 /* [RC 4] Parity register #0 read clear */ 53 #define BRB1_REG_BRB1_PRTY_STS_CLR 0x60130 54 /* [RW 10] At address BRB1_IND_FREE_LIST_PRS_CRDT initialize free head. At 55 * address BRB1_IND_FREE_LIST_PRS_CRDT+1 initialize free tail. At address 56 * BRB1_IND_FREE_LIST_PRS_CRDT+2 initialize parser initial credit. Warning - 57 * following reset the first rbc access to this reg must be write; there can 58 * be no more rbc writes after the first one; there can be any number of rbc 59 * read following the first write; rbc access not following these rules will 60 * result in hang condition. */ 61 #define BRB1_REG_FREE_LIST_PRS_CRDT 0x60200 62 /* [RW 10] The number of free blocks below which the full signal to class 0 63 * is asserted */ 64 #define BRB1_REG_FULL_0_XOFF_THRESHOLD_0 0x601d0 65 #define BRB1_REG_FULL_0_XOFF_THRESHOLD_1 0x60230 66 /* [RW 11] The number of free blocks above which the full signal to class 0 67 * is de-asserted */ 68 #define BRB1_REG_FULL_0_XON_THRESHOLD_0 0x601d4 69 #define BRB1_REG_FULL_0_XON_THRESHOLD_1 0x60234 70 /* [RW 11] The number of free blocks below which the full signal to class 1 71 * is asserted */ 72 #define BRB1_REG_FULL_1_XOFF_THRESHOLD_0 0x601d8 73 #define BRB1_REG_FULL_1_XOFF_THRESHOLD_1 0x60238 74 /* [RW 11] The number of free blocks above which the full signal to class 1 75 * is de-asserted */ 76 #define BRB1_REG_FULL_1_XON_THRESHOLD_0 0x601dc 77 #define BRB1_REG_FULL_1_XON_THRESHOLD_1 0x6023c 78 /* [RW 11] The number of free blocks below which the full signal to the LB 79 * port is asserted */ 80 #define BRB1_REG_FULL_LB_XOFF_THRESHOLD 0x601e0 81 /* [RW 10] The number of free blocks above which the full signal to the LB 82 * port is de-asserted */ 83 #define BRB1_REG_FULL_LB_XON_THRESHOLD 0x601e4 84 /* [RW 10] The number of free blocks above which the High_llfc signal to 85 interface #n is de-asserted. */ 86 #define BRB1_REG_HIGH_LLFC_HIGH_THRESHOLD_0 0x6014c 87 /* [RW 10] The number of free blocks below which the High_llfc signal to 88 interface #n is asserted. */ 89 #define BRB1_REG_HIGH_LLFC_LOW_THRESHOLD_0 0x6013c 90 /* [RW 11] The number of blocks guarantied for the LB port */ 91 #define BRB1_REG_LB_GUARANTIED 0x601ec 92 /* [RW 11] The hysteresis on the guarantied buffer space for the Lb port 93 * before signaling XON. */ 94 #define BRB1_REG_LB_GUARANTIED_HYST 0x60264 95 /* [RW 24] LL RAM data. */ 96 #define BRB1_REG_LL_RAM 0x61000 97 /* [RW 10] The number of free blocks above which the Low_llfc signal to 98 interface #n is de-asserted. */ 99 #define BRB1_REG_LOW_LLFC_HIGH_THRESHOLD_0 0x6016c 100 /* [RW 10] The number of free blocks below which the Low_llfc signal to 101 interface #n is asserted. */ 102 #define BRB1_REG_LOW_LLFC_LOW_THRESHOLD_0 0x6015c 103 /* [RW 11] The number of blocks guarantied for class 0 in MAC 0. The 104 * register is applicable only when per_class_guaranty_mode is set. */ 105 #define BRB1_REG_MAC_0_CLASS_0_GUARANTIED 0x60244 106 /* [RW 11] The hysteresis on the guarantied buffer space for class 0 in MAC 107 * 1 before signaling XON. The register is applicable only when 108 * per_class_guaranty_mode is set. */ 109 #define BRB1_REG_MAC_0_CLASS_0_GUARANTIED_HYST 0x60254 110 /* [RW 11] The number of blocks guarantied for class 1 in MAC 0. The 111 * register is applicable only when per_class_guaranty_mode is set. */ 112 #define BRB1_REG_MAC_0_CLASS_1_GUARANTIED 0x60248 113 /* [RW 11] The hysteresis on the guarantied buffer space for class 1in MAC 0 114 * before signaling XON. The register is applicable only when 115 * per_class_guaranty_mode is set. */ 116 #define BRB1_REG_MAC_0_CLASS_1_GUARANTIED_HYST 0x60258 117 /* [RW 11] The number of blocks guarantied for class 0in MAC1.The register 118 * is applicable only when per_class_guaranty_mode is set. */ 119 #define BRB1_REG_MAC_1_CLASS_0_GUARANTIED 0x6024c 120 /* [RW 11] The hysteresis on the guarantied buffer space for class 0 in MAC 121 * 1 before signaling XON. The register is applicable only when 122 * per_class_guaranty_mode is set. */ 123 #define BRB1_REG_MAC_1_CLASS_0_GUARANTIED_HYST 0x6025c 124 /* [RW 11] The number of blocks guarantied for class 1 in MAC 1. The 125 * register is applicable only when per_class_guaranty_mode is set. */ 126 #define BRB1_REG_MAC_1_CLASS_1_GUARANTIED 0x60250 127 /* [RW 11] The hysteresis on the guarantied buffer space for class 1 in MAC 128 * 1 before signaling XON. The register is applicable only when 129 * per_class_guaranty_mode is set. */ 130 #define BRB1_REG_MAC_1_CLASS_1_GUARANTIED_HYST 0x60260 131 /* [RW 11] The number of blocks guarantied for the MAC port. The register is 132 * applicable only when per_class_guaranty_mode is reset. */ 133 #define BRB1_REG_MAC_GUARANTIED_0 0x601e8 134 #define BRB1_REG_MAC_GUARANTIED_1 0x60240 135 /* [R 24] The number of full blocks. */ 136 #define BRB1_REG_NUM_OF_FULL_BLOCKS 0x60090 137 /* [ST 32] The number of cycles that the write_full signal towards MAC #0 138 was asserted. */ 139 #define BRB1_REG_NUM_OF_FULL_CYCLES_0 0x600c8 140 #define BRB1_REG_NUM_OF_FULL_CYCLES_1 0x600cc 141 #define BRB1_REG_NUM_OF_FULL_CYCLES_4 0x600d8 142 /* [ST 32] The number of cycles that the pause signal towards MAC #0 was 143 asserted. */ 144 #define BRB1_REG_NUM_OF_PAUSE_CYCLES_0 0x600b8 145 #define BRB1_REG_NUM_OF_PAUSE_CYCLES_1 0x600bc 146 /* [RW 10] The number of free blocks below which the pause signal to class 0 147 * is asserted */ 148 #define BRB1_REG_PAUSE_0_XOFF_THRESHOLD_0 0x601c0 149 #define BRB1_REG_PAUSE_0_XOFF_THRESHOLD_1 0x60220 150 /* [RW 11] The number of free blocks above which the pause signal to class 0 151 * is de-asserted */ 152 #define BRB1_REG_PAUSE_0_XON_THRESHOLD_0 0x601c4 153 #define BRB1_REG_PAUSE_0_XON_THRESHOLD_1 0x60224 154 /* [RW 11] The number of free blocks below which the pause signal to class 1 155 * is asserted */ 156 #define BRB1_REG_PAUSE_1_XOFF_THRESHOLD_0 0x601c8 157 #define BRB1_REG_PAUSE_1_XOFF_THRESHOLD_1 0x60228 158 /* [RW 11] The number of free blocks above which the pause signal to class 1 159 * is de-asserted */ 160 #define BRB1_REG_PAUSE_1_XON_THRESHOLD_0 0x601cc 161 #define BRB1_REG_PAUSE_1_XON_THRESHOLD_1 0x6022c 162 /* [RW 10] Write client 0: De-assert pause threshold. Not Functional */ 163 #define BRB1_REG_PAUSE_HIGH_THRESHOLD_0 0x60078 164 #define BRB1_REG_PAUSE_HIGH_THRESHOLD_1 0x6007c 165 /* [RW 10] Write client 0: Assert pause threshold. */ 166 #define BRB1_REG_PAUSE_LOW_THRESHOLD_0 0x60068 167 /* [RW 1] Indicates if to use per-class guaranty mode (new mode) or per-MAC 168 * guaranty mode (backwards-compatible mode). 0=per-MAC guaranty mode (BC 169 * mode). 1=per-class guaranty mode (new mode). */ 170 #define BRB1_REG_PER_CLASS_GUARANTY_MODE 0x60268 171 /* [R 24] The number of full blocks occpied by port. */ 172 #define BRB1_REG_PORT_NUM_OCC_BLOCKS_0 0x60094 173 /* [RW 1] Reset the design by software. */ 174 #define BRB1_REG_SOFT_RESET 0x600dc 175 /* [R 5] Used to read the value of the XX protection CAM occupancy counter. */ 176 #define CCM_REG_CAM_OCCUP 0xd0188 177 /* [RW 1] CM - CFC Interface enable. If 0 - the valid input is disregarded; 178 acknowledge output is deasserted; all other signals are treated as usual; 179 if 1 - normal activity. */ 180 #define CCM_REG_CCM_CFC_IFEN 0xd003c 181 /* [RW 1] CM - QM Interface enable. If 0 - the acknowledge input is 182 disregarded; valid is deasserted; all other signals are treated as usual; 183 if 1 - normal activity. */ 184 #define CCM_REG_CCM_CQM_IFEN 0xd000c 185 /* [RW 1] If set the Q index; received from the QM is inserted to event ID. 186 Otherwise 0 is inserted. */ 187 #define CCM_REG_CCM_CQM_USE_Q 0xd00c0 188 /* [RW 11] Interrupt mask register #0 read/write */ 189 #define CCM_REG_CCM_INT_MASK 0xd01e4 190 /* [R 11] Interrupt register #0 read */ 191 #define CCM_REG_CCM_INT_STS 0xd01d8 192 /* [RW 27] Parity mask register #0 read/write */ 193 #define CCM_REG_CCM_PRTY_MASK 0xd01f4 194 /* [R 27] Parity register #0 read */ 195 #define CCM_REG_CCM_PRTY_STS 0xd01e8 196 /* [RC 27] Parity register #0 read clear */ 197 #define CCM_REG_CCM_PRTY_STS_CLR 0xd01ec 198 /* [RW 3] The size of AG context region 0 in REG-pairs. Designates the MS 199 REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5). 200 Is used to determine the number of the AG context REG-pairs written back; 201 when the input message Reg1WbFlg isn't set. */ 202 #define CCM_REG_CCM_REG0_SZ 0xd00c4 203 /* [RW 1] CM - STORM 0 Interface enable. If 0 - the acknowledge input is 204 disregarded; valid is deasserted; all other signals are treated as usual; 205 if 1 - normal activity. */ 206 #define CCM_REG_CCM_STORM0_IFEN 0xd0004 207 /* [RW 1] CM - STORM 1 Interface enable. If 0 - the acknowledge input is 208 disregarded; valid is deasserted; all other signals are treated as usual; 209 if 1 - normal activity. */ 210 #define CCM_REG_CCM_STORM1_IFEN 0xd0008 211 /* [RW 1] CDU AG read Interface enable. If 0 - the request input is 212 disregarded; valid output is deasserted; all other signals are treated as 213 usual; if 1 - normal activity. */ 214 #define CCM_REG_CDU_AG_RD_IFEN 0xd0030 215 /* [RW 1] CDU AG write Interface enable. If 0 - the request and valid input 216 are disregarded; all other signals are treated as usual; if 1 - normal 217 activity. */ 218 #define CCM_REG_CDU_AG_WR_IFEN 0xd002c 219 /* [RW 1] CDU STORM read Interface enable. If 0 - the request input is 220 disregarded; valid output is deasserted; all other signals are treated as 221 usual; if 1 - normal activity. */ 222 #define CCM_REG_CDU_SM_RD_IFEN 0xd0038 223 /* [RW 1] CDU STORM write Interface enable. If 0 - the request and valid 224 input is disregarded; all other signals are treated as usual; if 1 - 225 normal activity. */ 226 #define CCM_REG_CDU_SM_WR_IFEN 0xd0034 227 /* [RW 4] CFC output initial credit. Max credit available - 15.Write writes 228 the initial credit value; read returns the current value of the credit 229 counter. Must be initialized to 1 at start-up. */ 230 #define CCM_REG_CFC_INIT_CRD 0xd0204 231 /* [RW 2] Auxiliary counter flag Q number 1. */ 232 #define CCM_REG_CNT_AUX1_Q 0xd00c8 233 /* [RW 2] Auxiliary counter flag Q number 2. */ 234 #define CCM_REG_CNT_AUX2_Q 0xd00cc 235 /* [RW 28] The CM header value for QM request (primary). */ 236 #define CCM_REG_CQM_CCM_HDR_P 0xd008c 237 /* [RW 28] The CM header value for QM request (secondary). */ 238 #define CCM_REG_CQM_CCM_HDR_S 0xd0090 239 /* [RW 1] QM - CM Interface enable. If 0 - the valid input is disregarded; 240 acknowledge output is deasserted; all other signals are treated as usual; 241 if 1 - normal activity. */ 242 #define CCM_REG_CQM_CCM_IFEN 0xd0014 243 /* [RW 6] QM output initial credit. Max credit available - 32. Write writes 244 the initial credit value; read returns the current value of the credit 245 counter. Must be initialized to 32 at start-up. */ 246 #define CCM_REG_CQM_INIT_CRD 0xd020c 247 /* [RW 3] The weight of the QM (primary) input in the WRR mechanism. 0 248 stands for weight 8 (the most prioritised); 1 stands for weight 1(least 249 prioritised); 2 stands for weight 2; tc. */ 250 #define CCM_REG_CQM_P_WEIGHT 0xd00b8 251 /* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0 252 stands for weight 8 (the most prioritised); 1 stands for weight 1(least 253 prioritised); 2 stands for weight 2; tc. */ 254 #define CCM_REG_CQM_S_WEIGHT 0xd00bc 255 /* [RW 1] Input SDM Interface enable. If 0 - the valid input is disregarded; 256 acknowledge output is deasserted; all other signals are treated as usual; 257 if 1 - normal activity. */ 258 #define CCM_REG_CSDM_IFEN 0xd0018 259 /* [RC 1] Set when the message length mismatch (relative to last indication) 260 at the SDM interface is detected. */ 261 #define CCM_REG_CSDM_LENGTH_MIS 0xd0170 262 /* [RW 3] The weight of the SDM input in the WRR mechanism. 0 stands for 263 weight 8 (the most prioritised); 1 stands for weight 1(least 264 prioritised); 2 stands for weight 2; tc. */ 265 #define CCM_REG_CSDM_WEIGHT 0xd00b4 266 /* [RW 28] The CM header for QM formatting in case of an error in the QM 267 inputs. */ 268 #define CCM_REG_ERR_CCM_HDR 0xd0094 269 /* [RW 8] The Event ID in case the input message ErrorFlg is set. */ 270 #define CCM_REG_ERR_EVNT_ID 0xd0098 271 /* [RW 8] FIC0 output initial credit. Max credit available - 255. Write 272 writes the initial credit value; read returns the current value of the 273 credit counter. Must be initialized to 64 at start-up. */ 274 #define CCM_REG_FIC0_INIT_CRD 0xd0210 275 /* [RW 8] FIC1 output initial credit. Max credit available - 255.Write 276 writes the initial credit value; read returns the current value of the 277 credit counter. Must be initialized to 64 at start-up. */ 278 #define CCM_REG_FIC1_INIT_CRD 0xd0214 279 /* [RW 1] Arbitration between Input Arbiter groups: 0 - fair Round-Robin; 1 280 - strict priority defined by ~ccm_registers_gr_ag_pr.gr_ag_pr; 281 ~ccm_registers_gr_ld0_pr.gr_ld0_pr and 282 ~ccm_registers_gr_ld1_pr.gr_ld1_pr. Groups are according to channels and 283 outputs to STORM: aggregation; load FIC0; load FIC1 and store. */ 284 #define CCM_REG_GR_ARB_TYPE 0xd015c 285 /* [RW 2] Load (FIC0) channel group priority. The lowest priority is 0; the 286 highest priority is 3. It is supposed; that the Store channel priority is 287 the compliment to 4 of the rest priorities - Aggregation channel; Load 288 (FIC0) channel and Load (FIC1). */ 289 #define CCM_REG_GR_LD0_PR 0xd0164 290 /* [RW 2] Load (FIC1) channel group priority. The lowest priority is 0; the 291 highest priority is 3. It is supposed; that the Store channel priority is 292 the compliment to 4 of the rest priorities - Aggregation channel; Load 293 (FIC0) channel and Load (FIC1). */ 294 #define CCM_REG_GR_LD1_PR 0xd0168 295 /* [RW 2] General flags index. */ 296 #define CCM_REG_INV_DONE_Q 0xd0108 297 /* [RW 4] The number of double REG-pairs(128 bits); loaded from the STORM 298 context and sent to STORM; for a specific connection type. The double 299 REG-pairs are used in order to align to STORM context row size of 128 300 bits. The offset of these data in the STORM context is always 0. Index 301 _(0..15) stands for the connection type (one of 16). */ 302 #define CCM_REG_N_SM_CTX_LD_0 0xd004c 303 #define CCM_REG_N_SM_CTX_LD_1 0xd0050 304 #define CCM_REG_N_SM_CTX_LD_2 0xd0054 305 #define CCM_REG_N_SM_CTX_LD_3 0xd0058 306 #define CCM_REG_N_SM_CTX_LD_4 0xd005c 307 /* [RW 1] Input pbf Interface enable. If 0 - the valid input is disregarded; 308 acknowledge output is deasserted; all other signals are treated as usual; 309 if 1 - normal activity. */ 310 #define CCM_REG_PBF_IFEN 0xd0028 311 /* [RC 1] Set when the message length mismatch (relative to last indication) 312 at the pbf interface is detected. */ 313 #define CCM_REG_PBF_LENGTH_MIS 0xd0180 314 /* [RW 3] The weight of the input pbf in the WRR mechanism. 0 stands for 315 weight 8 (the most prioritised); 1 stands for weight 1(least 316 prioritised); 2 stands for weight 2; tc. */ 317 #define CCM_REG_PBF_WEIGHT 0xd00ac 318 #define CCM_REG_PHYS_QNUM1_0 0xd0134 319 #define CCM_REG_PHYS_QNUM1_1 0xd0138 320 #define CCM_REG_PHYS_QNUM2_0 0xd013c 321 #define CCM_REG_PHYS_QNUM2_1 0xd0140 322 #define CCM_REG_PHYS_QNUM3_0 0xd0144 323 #define CCM_REG_PHYS_QNUM3_1 0xd0148 324 #define CCM_REG_QOS_PHYS_QNUM0_0 0xd0114 325 #define CCM_REG_QOS_PHYS_QNUM0_1 0xd0118 326 #define CCM_REG_QOS_PHYS_QNUM1_0 0xd011c 327 #define CCM_REG_QOS_PHYS_QNUM1_1 0xd0120 328 #define CCM_REG_QOS_PHYS_QNUM2_0 0xd0124 329 #define CCM_REG_QOS_PHYS_QNUM2_1 0xd0128 330 #define CCM_REG_QOS_PHYS_QNUM3_0 0xd012c 331 #define CCM_REG_QOS_PHYS_QNUM3_1 0xd0130 332 /* [RW 1] STORM - CM Interface enable. If 0 - the valid input is 333 disregarded; acknowledge output is deasserted; all other signals are 334 treated as usual; if 1 - normal activity. */ 335 #define CCM_REG_STORM_CCM_IFEN 0xd0010 336 /* [RC 1] Set when the message length mismatch (relative to last indication) 337 at the STORM interface is detected. */ 338 #define CCM_REG_STORM_LENGTH_MIS 0xd016c 339 /* [RW 3] The weight of the STORM input in the WRR (Weighted Round robin) 340 mechanism. 0 stands for weight 8 (the most prioritised); 1 stands for 341 weight 1(least prioritised); 2 stands for weight 2 (more prioritised); 342 tc. */ 343 #define CCM_REG_STORM_WEIGHT 0xd009c 344 /* [RW 1] Input tsem Interface enable. If 0 - the valid input is 345 disregarded; acknowledge output is deasserted; all other signals are 346 treated as usual; if 1 - normal activity. */ 347 #define CCM_REG_TSEM_IFEN 0xd001c 348 /* [RC 1] Set when the message length mismatch (relative to last indication) 349 at the tsem interface is detected. */ 350 #define CCM_REG_TSEM_LENGTH_MIS 0xd0174 351 /* [RW 3] The weight of the input tsem in the WRR mechanism. 0 stands for 352 weight 8 (the most prioritised); 1 stands for weight 1(least 353 prioritised); 2 stands for weight 2; tc. */ 354 #define CCM_REG_TSEM_WEIGHT 0xd00a0 355 /* [RW 1] Input usem Interface enable. If 0 - the valid input is 356 disregarded; acknowledge output is deasserted; all other signals are 357 treated as usual; if 1 - normal activity. */ 358 #define CCM_REG_USEM_IFEN 0xd0024 359 /* [RC 1] Set when message length mismatch (relative to last indication) at 360 the usem interface is detected. */ 361 #define CCM_REG_USEM_LENGTH_MIS 0xd017c 362 /* [RW 3] The weight of the input usem in the WRR mechanism. 0 stands for 363 weight 8 (the most prioritised); 1 stands for weight 1(least 364 prioritised); 2 stands for weight 2; tc. */ 365 #define CCM_REG_USEM_WEIGHT 0xd00a8 366 /* [RW 1] Input xsem Interface enable. If 0 - the valid input is 367 disregarded; acknowledge output is deasserted; all other signals are 368 treated as usual; if 1 - normal activity. */ 369 #define CCM_REG_XSEM_IFEN 0xd0020 370 /* [RC 1] Set when the message length mismatch (relative to last indication) 371 at the xsem interface is detected. */ 372 #define CCM_REG_XSEM_LENGTH_MIS 0xd0178 373 /* [RW 3] The weight of the input xsem in the WRR mechanism. 0 stands for 374 weight 8 (the most prioritised); 1 stands for weight 1(least 375 prioritised); 2 stands for weight 2; tc. */ 376 #define CCM_REG_XSEM_WEIGHT 0xd00a4 377 /* [RW 19] Indirect access to the descriptor table of the XX protection 378 mechanism. The fields are: [5:0] - message length; [12:6] - message 379 pointer; 18:13] - next pointer. */ 380 #define CCM_REG_XX_DESCR_TABLE 0xd0300 381 #define CCM_REG_XX_DESCR_TABLE_SIZE 24 382 /* [R 7] Used to read the value of XX protection Free counter. */ 383 #define CCM_REG_XX_FREE 0xd0184 384 /* [RW 6] Initial value for the credit counter; responsible for fulfilling 385 of the Input Stage XX protection buffer by the XX protection pending 386 messages. Max credit available - 127. Write writes the initial credit 387 value; read returns the current value of the credit counter. Must be 388 initialized to maximum XX protected message size - 2 at start-up. */ 389 #define CCM_REG_XX_INIT_CRD 0xd0220 390 /* [RW 7] The maximum number of pending messages; which may be stored in XX 391 protection. At read the ~ccm_registers_xx_free.xx_free counter is read. 392 At write comprises the start value of the ~ccm_registers_xx_free.xx_free 393 counter. */ 394 #define CCM_REG_XX_MSG_NUM 0xd0224 395 /* [RW 8] The Event ID; sent to the STORM in case of XX overflow. */ 396 #define CCM_REG_XX_OVFL_EVNT_ID 0xd0044 397 /* [RW 18] Indirect access to the XX table of the XX protection mechanism. 398 The fields are: [5:0] - tail pointer; 11:6] - Link List size; 17:12] - 399 header pointer. */ 400 #define CCM_REG_XX_TABLE 0xd0280 401 #define CDU_REG_CDU_CHK_MASK0 0x101000 402 #define CDU_REG_CDU_CHK_MASK1 0x101004 403 #define CDU_REG_CDU_CONTROL0 0x101008 404 #define CDU_REG_CDU_DEBUG 0x101010 405 #define CDU_REG_CDU_GLOBAL_PARAMS 0x101020 406 /* [RW 7] Interrupt mask register #0 read/write */ 407 #define CDU_REG_CDU_INT_MASK 0x10103c 408 /* [R 7] Interrupt register #0 read */ 409 #define CDU_REG_CDU_INT_STS 0x101030 410 /* [RW 5] Parity mask register #0 read/write */ 411 #define CDU_REG_CDU_PRTY_MASK 0x10104c 412 /* [R 5] Parity register #0 read */ 413 #define CDU_REG_CDU_PRTY_STS 0x101040 414 /* [RC 5] Parity register #0 read clear */ 415 #define CDU_REG_CDU_PRTY_STS_CLR 0x101044 416 /* [RC 32] logging of error data in case of a CDU load error: 417 {expected_cid[15:0]; xpected_type[2:0]; xpected_region[2:0]; ctive_error; 418 ype_error; ctual_active; ctual_compressed_context}; */ 419 #define CDU_REG_ERROR_DATA 0x101014 420 /* [WB 216] L1TT ram access. each entry has the following format : 421 {mrege_regions[7:0]; ffset12[5:0]...offset0[5:0]; 422 ength12[5:0]...length0[5:0]; d12[3:0]...id0[3:0]} */ 423 #define CDU_REG_L1TT 0x101800 424 /* [WB 24] MATT ram access. each entry has the following 425 format:{RegionLength[11:0]; egionOffset[11:0]} */ 426 #define CDU_REG_MATT 0x101100 427 /* [RW 1] when this bit is set the CDU operates in e1hmf mode */ 428 #define CDU_REG_MF_MODE 0x101050 429 /* [R 1] indication the initializing the activity counter by the hardware 430 was done. */ 431 #define CFC_REG_AC_INIT_DONE 0x104078 432 /* [RW 13] activity counter ram access */ 433 #define CFC_REG_ACTIVITY_COUNTER 0x104400 434 #define CFC_REG_ACTIVITY_COUNTER_SIZE 256 435 /* [R 1] indication the initializing the cams by the hardware was done. */ 436 #define CFC_REG_CAM_INIT_DONE 0x10407c 437 /* [RW 2] Interrupt mask register #0 read/write */ 438 #define CFC_REG_CFC_INT_MASK 0x104108 439 /* [R 2] Interrupt register #0 read */ 440 #define CFC_REG_CFC_INT_STS 0x1040fc 441 /* [RC 2] Interrupt register #0 read clear */ 442 #define CFC_REG_CFC_INT_STS_CLR 0x104100 443 /* [RW 4] Parity mask register #0 read/write */ 444 #define CFC_REG_CFC_PRTY_MASK 0x104118 445 /* [R 4] Parity register #0 read */ 446 #define CFC_REG_CFC_PRTY_STS 0x10410c 447 /* [RC 4] Parity register #0 read clear */ 448 #define CFC_REG_CFC_PRTY_STS_CLR 0x104110 449 /* [RW 21] CID cam access (21:1 - Data; alid - 0) */ 450 #define CFC_REG_CID_CAM 0x104800 451 #define CFC_REG_CONTROL0 0x104028 452 #define CFC_REG_DEBUG0 0x104050 453 /* [RW 14] indicates per error (in #cfc_registers_cfc_error_vector.cfc_error 454 vector) whether the cfc should be disabled upon it */ 455 #define CFC_REG_DISABLE_ON_ERROR 0x104044 456 /* [RC 14] CFC error vector. when the CFC detects an internal error it will 457 set one of these bits. the bit description can be found in CFC 458 specifications */ 459 #define CFC_REG_ERROR_VECTOR 0x10403c 460 /* [WB 93] LCID info ram access */ 461 #define CFC_REG_INFO_RAM 0x105000 462 #define CFC_REG_INFO_RAM_SIZE 1024 463 #define CFC_REG_INIT_REG 0x10404c 464 #define CFC_REG_INTERFACES 0x104058 465 /* [RW 24] {weight_load_client7[2:0] to weight_load_client0[2:0]}. this 466 field allows changing the priorities of the weighted-round-robin arbiter 467 which selects which CFC load client should be served next */ 468 #define CFC_REG_LCREQ_WEIGHTS 0x104084 469 /* [RW 16] Link List ram access; data = {prev_lcid; ext_lcid} */ 470 #define CFC_REG_LINK_LIST 0x104c00 471 #define CFC_REG_LINK_LIST_SIZE 256 472 /* [R 1] indication the initializing the link list by the hardware was done. */ 473 #define CFC_REG_LL_INIT_DONE 0x104074 474 /* [R 9] Number of allocated LCIDs which are at empty state */ 475 #define CFC_REG_NUM_LCIDS_ALLOC 0x104020 476 /* [R 9] Number of Arriving LCIDs in Link List Block */ 477 #define CFC_REG_NUM_LCIDS_ARRIVING 0x104004 478 #define CFC_REG_NUM_LCIDS_INSIDE_PF 0x104120 479 /* [R 9] Number of Leaving LCIDs in Link List Block */ 480 #define CFC_REG_NUM_LCIDS_LEAVING 0x104018 481 #define CFC_REG_WEAK_ENABLE_PF 0x104124 482 /* [RW 8] The event id for aggregated interrupt 0 */ 483 #define CSDM_REG_AGG_INT_EVENT_0 0xc2038 484 #define CSDM_REG_AGG_INT_EVENT_10 0xc2060 485 #define CSDM_REG_AGG_INT_EVENT_11 0xc2064 486 #define CSDM_REG_AGG_INT_EVENT_12 0xc2068 487 #define CSDM_REG_AGG_INT_EVENT_13 0xc206c 488 #define CSDM_REG_AGG_INT_EVENT_14 0xc2070 489 #define CSDM_REG_AGG_INT_EVENT_15 0xc2074 490 #define CSDM_REG_AGG_INT_EVENT_16 0xc2078 491 #define CSDM_REG_AGG_INT_EVENT_2 0xc2040 492 #define CSDM_REG_AGG_INT_EVENT_3 0xc2044 493 #define CSDM_REG_AGG_INT_EVENT_4 0xc2048 494 #define CSDM_REG_AGG_INT_EVENT_5 0xc204c 495 #define CSDM_REG_AGG_INT_EVENT_6 0xc2050 496 #define CSDM_REG_AGG_INT_EVENT_7 0xc2054 497 #define CSDM_REG_AGG_INT_EVENT_8 0xc2058 498 #define CSDM_REG_AGG_INT_EVENT_9 0xc205c 499 /* [RW 1] For each aggregated interrupt index whether the mode is normal (0) 500 or auto-mask-mode (1) */ 501 #define CSDM_REG_AGG_INT_MODE_10 0xc21e0 502 #define CSDM_REG_AGG_INT_MODE_11 0xc21e4 503 #define CSDM_REG_AGG_INT_MODE_12 0xc21e8 504 #define CSDM_REG_AGG_INT_MODE_13 0xc21ec 505 #define CSDM_REG_AGG_INT_MODE_14 0xc21f0 506 #define CSDM_REG_AGG_INT_MODE_15 0xc21f4 507 #define CSDM_REG_AGG_INT_MODE_16 0xc21f8 508 #define CSDM_REG_AGG_INT_MODE_6 0xc21d0 509 #define CSDM_REG_AGG_INT_MODE_7 0xc21d4 510 #define CSDM_REG_AGG_INT_MODE_8 0xc21d8 511 #define CSDM_REG_AGG_INT_MODE_9 0xc21dc 512 /* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */ 513 #define CSDM_REG_CFC_RSP_START_ADDR 0xc2008 514 /* [RW 16] The maximum value of the completion counter #0 */ 515 #define CSDM_REG_CMP_COUNTER_MAX0 0xc201c 516 /* [RW 16] The maximum value of the completion counter #1 */ 517 #define CSDM_REG_CMP_COUNTER_MAX1 0xc2020 518 /* [RW 16] The maximum value of the completion counter #2 */ 519 #define CSDM_REG_CMP_COUNTER_MAX2 0xc2024 520 /* [RW 16] The maximum value of the completion counter #3 */ 521 #define CSDM_REG_CMP_COUNTER_MAX3 0xc2028 522 /* [RW 13] The start address in the internal RAM for the completion 523 counters. */ 524 #define CSDM_REG_CMP_COUNTER_START_ADDR 0xc200c 525 /* [RW 32] Interrupt mask register #0 read/write */ 526 #define CSDM_REG_CSDM_INT_MASK_0 0xc229c 527 #define CSDM_REG_CSDM_INT_MASK_1 0xc22ac 528 /* [R 32] Interrupt register #0 read */ 529 #define CSDM_REG_CSDM_INT_STS_0 0xc2290 530 #define CSDM_REG_CSDM_INT_STS_1 0xc22a0 531 /* [RW 11] Parity mask register #0 read/write */ 532 #define CSDM_REG_CSDM_PRTY_MASK 0xc22bc 533 /* [R 11] Parity register #0 read */ 534 #define CSDM_REG_CSDM_PRTY_STS 0xc22b0 535 /* [RC 11] Parity register #0 read clear */ 536 #define CSDM_REG_CSDM_PRTY_STS_CLR 0xc22b4 537 #define CSDM_REG_ENABLE_IN1 0xc2238 538 #define CSDM_REG_ENABLE_IN2 0xc223c 539 #define CSDM_REG_ENABLE_OUT1 0xc2240 540 #define CSDM_REG_ENABLE_OUT2 0xc2244 541 /* [RW 4] The initial number of messages that can be sent to the pxp control 542 interface without receiving any ACK. */ 543 #define CSDM_REG_INIT_CREDIT_PXP_CTRL 0xc24bc 544 /* [ST 32] The number of ACK after placement messages received */ 545 #define CSDM_REG_NUM_OF_ACK_AFTER_PLACE 0xc227c 546 /* [ST 32] The number of packet end messages received from the parser */ 547 #define CSDM_REG_NUM_OF_PKT_END_MSG 0xc2274 548 /* [ST 32] The number of requests received from the pxp async if */ 549 #define CSDM_REG_NUM_OF_PXP_ASYNC_REQ 0xc2278 550 /* [ST 32] The number of commands received in queue 0 */ 551 #define CSDM_REG_NUM_OF_Q0_CMD 0xc2248 552 /* [ST 32] The number of commands received in queue 10 */ 553 #define CSDM_REG_NUM_OF_Q10_CMD 0xc226c 554 /* [ST 32] The number of commands received in queue 11 */ 555 #define CSDM_REG_NUM_OF_Q11_CMD 0xc2270 556 /* [ST 32] The number of commands received in queue 1 */ 557 #define CSDM_REG_NUM_OF_Q1_CMD 0xc224c 558 /* [ST 32] The number of commands received in queue 3 */ 559 #define CSDM_REG_NUM_OF_Q3_CMD 0xc2250 560 /* [ST 32] The number of commands received in queue 4 */ 561 #define CSDM_REG_NUM_OF_Q4_CMD 0xc2254 562 /* [ST 32] The number of commands received in queue 5 */ 563 #define CSDM_REG_NUM_OF_Q5_CMD 0xc2258 564 /* [ST 32] The number of commands received in queue 6 */ 565 #define CSDM_REG_NUM_OF_Q6_CMD 0xc225c 566 /* [ST 32] The number of commands received in queue 7 */ 567 #define CSDM_REG_NUM_OF_Q7_CMD 0xc2260 568 /* [ST 32] The number of commands received in queue 8 */ 569 #define CSDM_REG_NUM_OF_Q8_CMD 0xc2264 570 /* [ST 32] The number of commands received in queue 9 */ 571 #define CSDM_REG_NUM_OF_Q9_CMD 0xc2268 572 /* [RW 13] The start address in the internal RAM for queue counters */ 573 #define CSDM_REG_Q_COUNTER_START_ADDR 0xc2010 574 /* [R 1] pxp_ctrl rd_data fifo empty in sdm_dma_rsp block */ 575 #define CSDM_REG_RSP_PXP_CTRL_RDATA_EMPTY 0xc2548 576 /* [R 1] parser fifo empty in sdm_sync block */ 577 #define CSDM_REG_SYNC_PARSER_EMPTY 0xc2550 578 /* [R 1] parser serial fifo empty in sdm_sync block */ 579 #define CSDM_REG_SYNC_SYNC_EMPTY 0xc2558 580 /* [RW 32] Tick for timer counter. Applicable only when 581 ~csdm_registers_timer_tick_enable.timer_tick_enable =1 */ 582 #define CSDM_REG_TIMER_TICK 0xc2000 583 /* [RW 5] The number of time_slots in the arbitration cycle */ 584 #define CSEM_REG_ARB_CYCLE_SIZE 0x200034 585 /* [RW 3] The source that is associated with arbitration element 0. Source 586 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 587 sleeping thread with priority 1; 4- sleeping thread with priority 2 */ 588 #define CSEM_REG_ARB_ELEMENT0 0x200020 589 /* [RW 3] The source that is associated with arbitration element 1. Source 590 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 591 sleeping thread with priority 1; 4- sleeping thread with priority 2. 592 Could not be equal to register ~csem_registers_arb_element0.arb_element0 */ 593 #define CSEM_REG_ARB_ELEMENT1 0x200024 594 /* [RW 3] The source that is associated with arbitration element 2. Source 595 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 596 sleeping thread with priority 1; 4- sleeping thread with priority 2. 597 Could not be equal to register ~csem_registers_arb_element0.arb_element0 598 and ~csem_registers_arb_element1.arb_element1 */ 599 #define CSEM_REG_ARB_ELEMENT2 0x200028 600 /* [RW 3] The source that is associated with arbitration element 3. Source 601 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 602 sleeping thread with priority 1; 4- sleeping thread with priority 2.Could 603 not be equal to register ~csem_registers_arb_element0.arb_element0 and 604 ~csem_registers_arb_element1.arb_element1 and 605 ~csem_registers_arb_element2.arb_element2 */ 606 #define CSEM_REG_ARB_ELEMENT3 0x20002c 607 /* [RW 3] The source that is associated with arbitration element 4. Source 608 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 609 sleeping thread with priority 1; 4- sleeping thread with priority 2. 610 Could not be equal to register ~csem_registers_arb_element0.arb_element0 611 and ~csem_registers_arb_element1.arb_element1 and 612 ~csem_registers_arb_element2.arb_element2 and 613 ~csem_registers_arb_element3.arb_element3 */ 614 #define CSEM_REG_ARB_ELEMENT4 0x200030 615 /* [RW 32] Interrupt mask register #0 read/write */ 616 #define CSEM_REG_CSEM_INT_MASK_0 0x200110 617 #define CSEM_REG_CSEM_INT_MASK_1 0x200120 618 /* [R 32] Interrupt register #0 read */ 619 #define CSEM_REG_CSEM_INT_STS_0 0x200104 620 #define CSEM_REG_CSEM_INT_STS_1 0x200114 621 /* [RW 32] Parity mask register #0 read/write */ 622 #define CSEM_REG_CSEM_PRTY_MASK_0 0x200130 623 #define CSEM_REG_CSEM_PRTY_MASK_1 0x200140 624 /* [R 32] Parity register #0 read */ 625 #define CSEM_REG_CSEM_PRTY_STS_0 0x200124 626 #define CSEM_REG_CSEM_PRTY_STS_1 0x200134 627 /* [RC 32] Parity register #0 read clear */ 628 #define CSEM_REG_CSEM_PRTY_STS_CLR_0 0x200128 629 #define CSEM_REG_CSEM_PRTY_STS_CLR_1 0x200138 630 #define CSEM_REG_ENABLE_IN 0x2000a4 631 #define CSEM_REG_ENABLE_OUT 0x2000a8 632 /* [RW 32] This address space contains all registers and memories that are 633 placed in SEM_FAST block. The SEM_FAST registers are described in 634 appendix B. In order to access the sem_fast registers the base address 635 ~fast_memory.fast_memory should be added to eachsem_fast register offset. */ 636 #define CSEM_REG_FAST_MEMORY 0x220000 637 /* [RW 1] Disables input messages from FIC0 May be updated during run_time 638 by the microcode */ 639 #define CSEM_REG_FIC0_DISABLE 0x200224 640 /* [RW 1] Disables input messages from FIC1 May be updated during run_time 641 by the microcode */ 642 #define CSEM_REG_FIC1_DISABLE 0x200234 643 /* [RW 15] Interrupt table Read and write access to it is not possible in 644 the middle of the work */ 645 #define CSEM_REG_INT_TABLE 0x200400 646 /* [ST 24] Statistics register. The number of messages that entered through 647 FIC0 */ 648 #define CSEM_REG_MSG_NUM_FIC0 0x200000 649 /* [ST 24] Statistics register. The number of messages that entered through 650 FIC1 */ 651 #define CSEM_REG_MSG_NUM_FIC1 0x200004 652 /* [ST 24] Statistics register. The number of messages that were sent to 653 FOC0 */ 654 #define CSEM_REG_MSG_NUM_FOC0 0x200008 655 /* [ST 24] Statistics register. The number of messages that were sent to 656 FOC1 */ 657 #define CSEM_REG_MSG_NUM_FOC1 0x20000c 658 /* [ST 24] Statistics register. The number of messages that were sent to 659 FOC2 */ 660 #define CSEM_REG_MSG_NUM_FOC2 0x200010 661 /* [ST 24] Statistics register. The number of messages that were sent to 662 FOC3 */ 663 #define CSEM_REG_MSG_NUM_FOC3 0x200014 664 /* [RW 1] Disables input messages from the passive buffer May be updated 665 during run_time by the microcode */ 666 #define CSEM_REG_PAS_DISABLE 0x20024c 667 /* [WB 128] Debug only. Passive buffer memory */ 668 #define CSEM_REG_PASSIVE_BUFFER 0x202000 669 /* [WB 46] pram memory. B45 is parity; b[44:0] - data. */ 670 #define CSEM_REG_PRAM 0x240000 671 /* [R 16] Valid sleeping threads indication have bit per thread */ 672 #define CSEM_REG_SLEEP_THREADS_VALID 0x20026c 673 /* [R 1] EXT_STORE FIFO is empty in sem_slow_ls_ext */ 674 #define CSEM_REG_SLOW_EXT_STORE_EMPTY 0x2002a0 675 /* [RW 16] List of free threads . There is a bit per thread. */ 676 #define CSEM_REG_THREADS_LIST 0x2002e4 677 /* [RW 3] The arbitration scheme of time_slot 0 */ 678 #define CSEM_REG_TS_0_AS 0x200038 679 /* [RW 3] The arbitration scheme of time_slot 10 */ 680 #define CSEM_REG_TS_10_AS 0x200060 681 /* [RW 3] The arbitration scheme of time_slot 11 */ 682 #define CSEM_REG_TS_11_AS 0x200064 683 /* [RW 3] The arbitration scheme of time_slot 12 */ 684 #define CSEM_REG_TS_12_AS 0x200068 685 /* [RW 3] The arbitration scheme of time_slot 13 */ 686 #define CSEM_REG_TS_13_AS 0x20006c 687 /* [RW 3] The arbitration scheme of time_slot 14 */ 688 #define CSEM_REG_TS_14_AS 0x200070 689 /* [RW 3] The arbitration scheme of time_slot 15 */ 690 #define CSEM_REG_TS_15_AS 0x200074 691 /* [RW 3] The arbitration scheme of time_slot 16 */ 692 #define CSEM_REG_TS_16_AS 0x200078 693 /* [RW 3] The arbitration scheme of time_slot 17 */ 694 #define CSEM_REG_TS_17_AS 0x20007c 695 /* [RW 3] The arbitration scheme of time_slot 18 */ 696 #define CSEM_REG_TS_18_AS 0x200080 697 /* [RW 3] The arbitration scheme of time_slot 1 */ 698 #define CSEM_REG_TS_1_AS 0x20003c 699 /* [RW 3] The arbitration scheme of time_slot 2 */ 700 #define CSEM_REG_TS_2_AS 0x200040 701 /* [RW 3] The arbitration scheme of time_slot 3 */ 702 #define CSEM_REG_TS_3_AS 0x200044 703 /* [RW 3] The arbitration scheme of time_slot 4 */ 704 #define CSEM_REG_TS_4_AS 0x200048 705 /* [RW 3] The arbitration scheme of time_slot 5 */ 706 #define CSEM_REG_TS_5_AS 0x20004c 707 /* [RW 3] The arbitration scheme of time_slot 6 */ 708 #define CSEM_REG_TS_6_AS 0x200050 709 /* [RW 3] The arbitration scheme of time_slot 7 */ 710 #define CSEM_REG_TS_7_AS 0x200054 711 /* [RW 3] The arbitration scheme of time_slot 8 */ 712 #define CSEM_REG_TS_8_AS 0x200058 713 /* [RW 3] The arbitration scheme of time_slot 9 */ 714 #define CSEM_REG_TS_9_AS 0x20005c 715 /* [W 7] VF or PF ID for reset error bit. Values 0-63 reset error bit for 64 716 * VF; values 64-67 reset error for 4 PF; values 68-127 are not valid. */ 717 #define CSEM_REG_VFPF_ERR_NUM 0x200380 718 /* [RW 1] Parity mask register #0 read/write */ 719 #define DBG_REG_DBG_PRTY_MASK 0xc0a8 720 /* [R 1] Parity register #0 read */ 721 #define DBG_REG_DBG_PRTY_STS 0xc09c 722 /* [RC 1] Parity register #0 read clear */ 723 #define DBG_REG_DBG_PRTY_STS_CLR 0xc0a0 724 /* [RW 1] When set the DMAE will process the commands as in E1.5. 1.The 725 * function that is used is always SRC-PCI; 2.VF_Valid = 0; 3.VFID=0; 726 * 4.Completion function=0; 5.Error handling=0 */ 727 #define DMAE_REG_BACKWARD_COMP_EN 0x10207c 728 /* [RW 32] Commands memory. The address to command X; row Y is to calculated 729 as 14*X+Y. */ 730 #define DMAE_REG_CMD_MEM 0x102400 731 #define DMAE_REG_CMD_MEM_SIZE 224 732 /* [RW 1] If 0 - the CRC-16c initial value is all zeroes; if 1 - the CRC-16c 733 initial value is all ones. */ 734 #define DMAE_REG_CRC16C_INIT 0x10201c 735 /* [RW 1] If 0 - the CRC-16 T10 initial value is all zeroes; if 1 - the 736 CRC-16 T10 initial value is all ones. */ 737 #define DMAE_REG_CRC16T10_INIT 0x102020 738 /* [RW 2] Interrupt mask register #0 read/write */ 739 #define DMAE_REG_DMAE_INT_MASK 0x102054 740 /* [RW 4] Parity mask register #0 read/write */ 741 #define DMAE_REG_DMAE_PRTY_MASK 0x102064 742 /* [R 4] Parity register #0 read */ 743 #define DMAE_REG_DMAE_PRTY_STS 0x102058 744 /* [RC 4] Parity register #0 read clear */ 745 #define DMAE_REG_DMAE_PRTY_STS_CLR 0x10205c 746 /* [RW 1] Command 0 go. */ 747 #define DMAE_REG_GO_C0 0x102080 748 /* [RW 1] Command 1 go. */ 749 #define DMAE_REG_GO_C1 0x102084 750 /* [RW 1] Command 10 go. */ 751 #define DMAE_REG_GO_C10 0x102088 752 /* [RW 1] Command 11 go. */ 753 #define DMAE_REG_GO_C11 0x10208c 754 /* [RW 1] Command 12 go. */ 755 #define DMAE_REG_GO_C12 0x102090 756 /* [RW 1] Command 13 go. */ 757 #define DMAE_REG_GO_C13 0x102094 758 /* [RW 1] Command 14 go. */ 759 #define DMAE_REG_GO_C14 0x102098 760 /* [RW 1] Command 15 go. */ 761 #define DMAE_REG_GO_C15 0x10209c 762 /* [RW 1] Command 2 go. */ 763 #define DMAE_REG_GO_C2 0x1020a0 764 /* [RW 1] Command 3 go. */ 765 #define DMAE_REG_GO_C3 0x1020a4 766 /* [RW 1] Command 4 go. */ 767 #define DMAE_REG_GO_C4 0x1020a8 768 /* [RW 1] Command 5 go. */ 769 #define DMAE_REG_GO_C5 0x1020ac 770 /* [RW 1] Command 6 go. */ 771 #define DMAE_REG_GO_C6 0x1020b0 772 /* [RW 1] Command 7 go. */ 773 #define DMAE_REG_GO_C7 0x1020b4 774 /* [RW 1] Command 8 go. */ 775 #define DMAE_REG_GO_C8 0x1020b8 776 /* [RW 1] Command 9 go. */ 777 #define DMAE_REG_GO_C9 0x1020bc 778 /* [RW 1] DMAE GRC Interface (Target; aster) enable. If 0 - the acknowledge 779 input is disregarded; valid is deasserted; all other signals are treated 780 as usual; if 1 - normal activity. */ 781 #define DMAE_REG_GRC_IFEN 0x102008 782 /* [RW 1] DMAE PCI Interface (Request; ead; rite) enable. If 0 - the 783 acknowledge input is disregarded; valid is deasserted; full is asserted; 784 all other signals are treated as usual; if 1 - normal activity. */ 785 #define DMAE_REG_PCI_IFEN 0x102004 786 /* [RW 4] DMAE- PCI Request Interface initial credit. Write writes the 787 initial value to the credit counter; related to the address. Read returns 788 the current value of the counter. */ 789 #define DMAE_REG_PXP_REQ_INIT_CRD 0x1020c0 790 /* [RW 8] Aggregation command. */ 791 #define DORQ_REG_AGG_CMD0 0x170060 792 /* [RW 8] Aggregation command. */ 793 #define DORQ_REG_AGG_CMD1 0x170064 794 /* [RW 8] Aggregation command. */ 795 #define DORQ_REG_AGG_CMD2 0x170068 796 /* [RW 8] Aggregation command. */ 797 #define DORQ_REG_AGG_CMD3 0x17006c 798 /* [RW 28] UCM Header. */ 799 #define DORQ_REG_CMHEAD_RX 0x170050 800 /* [RW 32] Doorbell address for RBC doorbells (function 0). */ 801 #define DORQ_REG_DB_ADDR0 0x17008c 802 /* [RW 5] Interrupt mask register #0 read/write */ 803 #define DORQ_REG_DORQ_INT_MASK 0x170180 804 /* [R 5] Interrupt register #0 read */ 805 #define DORQ_REG_DORQ_INT_STS 0x170174 806 /* [RC 5] Interrupt register #0 read clear */ 807 #define DORQ_REG_DORQ_INT_STS_CLR 0x170178 808 /* [RW 2] Parity mask register #0 read/write */ 809 #define DORQ_REG_DORQ_PRTY_MASK 0x170190 810 /* [R 2] Parity register #0 read */ 811 #define DORQ_REG_DORQ_PRTY_STS 0x170184 812 /* [RC 2] Parity register #0 read clear */ 813 #define DORQ_REG_DORQ_PRTY_STS_CLR 0x170188 814 /* [RW 8] The address to write the DPM CID to STORM. */ 815 #define DORQ_REG_DPM_CID_ADDR 0x170044 816 /* [RW 5] The DPM mode CID extraction offset. */ 817 #define DORQ_REG_DPM_CID_OFST 0x170030 818 /* [RW 12] The threshold of the DQ FIFO to send the almost full interrupt. */ 819 #define DORQ_REG_DQ_FIFO_AFULL_TH 0x17007c 820 /* [RW 12] The threshold of the DQ FIFO to send the full interrupt. */ 821 #define DORQ_REG_DQ_FIFO_FULL_TH 0x170078 822 /* [R 13] Current value of the DQ FIFO fill level according to following 823 pointer. The range is 0 - 256 FIFO rows; where each row stands for the 824 doorbell. */ 825 #define DORQ_REG_DQ_FILL_LVLF 0x1700a4 826 /* [R 1] DQ FIFO full status. Is set; when FIFO filling level is more or 827 equal to full threshold; reset on full clear. */ 828 #define DORQ_REG_DQ_FULL_ST 0x1700c0 829 /* [RW 28] The value sent to CM header in the case of CFC load error. */ 830 #define DORQ_REG_ERR_CMHEAD 0x170058 831 #define DORQ_REG_IF_EN 0x170004 832 #define DORQ_REG_MAX_RVFID_SIZE 0x1701ec 833 #define DORQ_REG_MODE_ACT 0x170008 834 /* [RW 5] The normal mode CID extraction offset. */ 835 #define DORQ_REG_NORM_CID_OFST 0x17002c 836 /* [RW 28] TCM Header when only TCP context is loaded. */ 837 #define DORQ_REG_NORM_CMHEAD_TX 0x17004c 838 /* [RW 3] The number of simultaneous outstanding requests to Context Fetch 839 Interface. */ 840 #define DORQ_REG_OUTST_REQ 0x17003c 841 #define DORQ_REG_PF_USAGE_CNT 0x1701d0 842 #define DORQ_REG_REGN 0x170038 843 /* [R 4] Current value of response A counter credit. Initial credit is 844 configured through write to ~dorq_registers_rsp_init_crd.rsp_init_crd 845 register. */ 846 #define DORQ_REG_RSPA_CRD_CNT 0x1700ac 847 /* [R 4] Current value of response B counter credit. Initial credit is 848 configured through write to ~dorq_registers_rsp_init_crd.rsp_init_crd 849 register. */ 850 #define DORQ_REG_RSPB_CRD_CNT 0x1700b0 851 /* [RW 4] The initial credit at the Doorbell Response Interface. The write 852 writes the same initial credit to the rspa_crd_cnt and rspb_crd_cnt. The 853 read reads this written value. */ 854 #define DORQ_REG_RSP_INIT_CRD 0x170048 855 #define DORQ_REG_RSPB_CRD_CNT 0x1700b0 856 #define DORQ_REG_VF_NORM_CID_BASE 0x1701a0 857 #define DORQ_REG_VF_NORM_CID_OFST 0x1701f4 858 #define DORQ_REG_VF_NORM_CID_WND_SIZE 0x1701a4 859 #define DORQ_REG_VF_NORM_MAX_CID_COUNT 0x1701e4 860 #define DORQ_REG_VF_NORM_VF_BASE 0x1701a8 861 /* [RW 10] VF type validation mask value */ 862 #define DORQ_REG_VF_TYPE_MASK_0 0x170218 863 /* [RW 17] VF type validation Min MCID value */ 864 #define DORQ_REG_VF_TYPE_MAX_MCID_0 0x1702d8 865 /* [RW 17] VF type validation Max MCID value */ 866 #define DORQ_REG_VF_TYPE_MIN_MCID_0 0x170298 867 /* [RW 10] VF type validation comp value */ 868 #define DORQ_REG_VF_TYPE_VALUE_0 0x170258 869 #define DORQ_REG_VF_USAGE_CT_LIMIT 0x170340 870 871 /* [RW 4] Initial activity counter value on the load request; when the 872 shortcut is done. */ 873 #define DORQ_REG_SHRT_ACT_CNT 0x170070 874 /* [RW 28] TCM Header when both ULP and TCP context is loaded. */ 875 #define DORQ_REG_SHRT_CMHEAD 0x170054 876 #define HC_CONFIG_0_REG_ATTN_BIT_EN_0 (0x1<<4) 877 #define HC_CONFIG_0_REG_BLOCK_DISABLE_0 (0x1<<0) 878 #define HC_CONFIG_0_REG_INT_LINE_EN_0 (0x1<<3) 879 #define HC_CONFIG_0_REG_MSI_ATTN_EN_0 (0x1<<7) 880 #define HC_CONFIG_0_REG_MSI_MSIX_INT_EN_0 (0x1<<2) 881 #define HC_CONFIG_0_REG_SINGLE_ISR_EN_0 (0x1<<1) 882 #define HC_CONFIG_1_REG_BLOCK_DISABLE_1 (0x1<<0) 883 #define DORQ_REG_VF_USAGE_CNT 0x170320 884 #define HC_REG_AGG_INT_0 0x108050 885 #define HC_REG_AGG_INT_1 0x108054 886 #define HC_REG_ATTN_BIT 0x108120 887 #define HC_REG_ATTN_IDX 0x108100 888 #define HC_REG_ATTN_MSG0_ADDR_L 0x108018 889 #define HC_REG_ATTN_MSG1_ADDR_L 0x108020 890 #define HC_REG_ATTN_NUM_P0 0x108038 891 #define HC_REG_ATTN_NUM_P1 0x10803c 892 #define HC_REG_COMMAND_REG 0x108180 893 #define HC_REG_CONFIG_0 0x108000 894 #define HC_REG_CONFIG_1 0x108004 895 #define HC_REG_FUNC_NUM_P0 0x1080ac 896 #define HC_REG_FUNC_NUM_P1 0x1080b0 897 /* [RW 3] Parity mask register #0 read/write */ 898 #define HC_REG_HC_PRTY_MASK 0x1080a0 899 /* [R 3] Parity register #0 read */ 900 #define HC_REG_HC_PRTY_STS 0x108094 901 /* [RC 3] Parity register #0 read clear */ 902 #define HC_REG_HC_PRTY_STS_CLR 0x108098 903 #define HC_REG_INT_MASK 0x108108 904 #define HC_REG_LEADING_EDGE_0 0x108040 905 #define HC_REG_LEADING_EDGE_1 0x108048 906 #define HC_REG_MAIN_MEMORY 0x108800 907 #define HC_REG_MAIN_MEMORY_SIZE 152 908 #define HC_REG_P0_PROD_CONS 0x108200 909 #define HC_REG_P1_PROD_CONS 0x108400 910 #define HC_REG_PBA_COMMAND 0x108140 911 #define HC_REG_PCI_CONFIG_0 0x108010 912 #define HC_REG_PCI_CONFIG_1 0x108014 913 #define HC_REG_STATISTIC_COUNTERS 0x109000 914 #define HC_REG_TRAILING_EDGE_0 0x108044 915 #define HC_REG_TRAILING_EDGE_1 0x10804c 916 #define HC_REG_UC_RAM_ADDR_0 0x108028 917 #define HC_REG_UC_RAM_ADDR_1 0x108030 918 #define HC_REG_USTORM_ADDR_FOR_COALESCE 0x108068 919 #define HC_REG_VQID_0 0x108008 920 #define HC_REG_VQID_1 0x10800c 921 #define IGU_BLOCK_CONFIGURATION_REG_BACKWARD_COMP_EN (0x1<<1) 922 #define IGU_BLOCK_CONFIGURATION_REG_BLOCK_ENABLE (0x1<<0) 923 #define IGU_REG_ATTENTION_ACK_BITS 0x130108 924 /* [R 4] Debug: attn_fsm */ 925 #define IGU_REG_ATTN_FSM 0x130054 926 #define IGU_REG_ATTN_MSG_ADDR_H 0x13011c 927 #define IGU_REG_ATTN_MSG_ADDR_L 0x130120 928 /* [R 4] Debug: [3] - attention write done message is pending (0-no pending; 929 * 1-pending). [2:0] = PFID. Pending means attention message was sent; but 930 * write done didn't receive. */ 931 #define IGU_REG_ATTN_WRITE_DONE_PENDING 0x130030 932 #define IGU_REG_BLOCK_CONFIGURATION 0x130000 933 #define IGU_REG_COMMAND_REG_32LSB_DATA 0x130124 934 #define IGU_REG_COMMAND_REG_CTRL 0x13012c 935 /* [WB_R 32] Cleanup bit status per SB. 1 = cleanup is set. 0 = cleanup bit 936 * is clear. The bits in this registers are set and clear via the producer 937 * command. Data valid only in addresses 0-4. all the rest are zero. */ 938 #define IGU_REG_CSTORM_TYPE_0_SB_CLEANUP 0x130200 939 /* [R 5] Debug: ctrl_fsm */ 940 #define IGU_REG_CTRL_FSM 0x130064 941 /* [R 1] data available for error memory. If this bit is clear do not red 942 * from error_handling_memory. */ 943 #define IGU_REG_ERROR_HANDLING_DATA_VALID 0x130130 944 /* [RW 11] Parity mask register #0 read/write */ 945 #define IGU_REG_IGU_PRTY_MASK 0x1300a8 946 /* [R 11] Parity register #0 read */ 947 #define IGU_REG_IGU_PRTY_STS 0x13009c 948 /* [RC 11] Parity register #0 read clear */ 949 #define IGU_REG_IGU_PRTY_STS_CLR 0x1300a0 950 /* [R 4] Debug: int_handle_fsm */ 951 #define IGU_REG_INT_HANDLE_FSM 0x130050 952 #define IGU_REG_LEADING_EDGE_LATCH 0x130134 953 /* [RW 14] mapping CAM; relevant for E2 operating mode only. [0] - valid. 954 * [6:1] - vector number; [13:7] - FID (if VF - [13] = 0; [12:7] = VF 955 * number; if PF - [13] = 1; [12:10] = 0; [9:7] = PF number); */ 956 #define IGU_REG_MAPPING_MEMORY 0x131000 957 #define IGU_REG_MAPPING_MEMORY_SIZE 136 958 #define IGU_REG_PBA_STATUS_LSB 0x130138 959 #define IGU_REG_PBA_STATUS_MSB 0x13013c 960 #define IGU_REG_PCI_PF_MSI_EN 0x130140 961 #define IGU_REG_PCI_PF_MSIX_EN 0x130144 962 #define IGU_REG_PCI_PF_MSIX_FUNC_MASK 0x130148 963 /* [WB_R 32] Each bit represent the pending bits status for that SB. 0 = no 964 * pending; 1 = pending. Pendings means interrupt was asserted; and write 965 * done was not received. Data valid only in addresses 0-4. all the rest are 966 * zero. */ 967 #define IGU_REG_PENDING_BITS_STATUS 0x130300 968 #define IGU_REG_PF_CONFIGURATION 0x130154 969 /* [RW 20] producers only. E2 mode: address 0-135 match to the mapping 970 * memory; 136 - PF0 default prod; 137 PF1 default prod; 138 - PF2 default 971 * prod; 139 PF3 default prod; 140 - PF0 - ATTN prod; 141 - PF1 - ATTN prod; 972 * 142 - PF2 - ATTN prod; 143 - PF3 - ATTN prod; 144-147 reserved. E1.5 mode 973 * - In backward compatible mode; for non default SB; each even line in the 974 * memory holds the U producer and each odd line hold the C producer. The 975 * first 128 producer are for NDSB (PF0 - 0-31; PF1 - 32-63 and so on). The 976 * last 20 producers are for the DSB for each PF. each PF has five segments 977 * (the order inside each segment is PF0; PF1; PF2; PF3) - 128-131 U prods; 978 * 132-135 C prods; 136-139 X prods; 140-143 T prods; 144-147 ATTN prods; */ 979 #define IGU_REG_PROD_CONS_MEMORY 0x132000 980 /* [R 3] Debug: pxp_arb_fsm */ 981 #define IGU_REG_PXP_ARB_FSM 0x130068 982 /* [RW 6] Write one for each bit will reset the appropriate memory. When the 983 * memory reset finished the appropriate bit will be clear. Bit 0 - mapping 984 * memory; Bit 1 - SB memory; Bit 2 - SB interrupt and mask register; Bit 3 985 * - MSIX memory; Bit 4 - PBA memory; Bit 5 - statistics; */ 986 #define IGU_REG_RESET_MEMORIES 0x130158 987 /* [R 4] Debug: sb_ctrl_fsm */ 988 #define IGU_REG_SB_CTRL_FSM 0x13004c 989 #define IGU_REG_SB_INT_BEFORE_MASK_LSB 0x13015c 990 #define IGU_REG_SB_INT_BEFORE_MASK_MSB 0x130160 991 #define IGU_REG_SB_MASK_LSB 0x130164 992 #define IGU_REG_SB_MASK_MSB 0x130168 993 /* [RW 16] Number of command that were dropped without causing an interrupt 994 * due to: read access for WO BAR address; or write access for RO BAR 995 * address or any access for reserved address or PCI function error is set 996 * and address is not MSIX; PBA or cleanup */ 997 #define IGU_REG_SILENT_DROP 0x13016c 998 /* [RW 10] Number of MSI/MSIX/ATTN messages sent for the function: 0-63 - 999 * number of MSIX messages per VF; 64-67 - number of MSI/MSIX messages per 1000 * PF; 68-71 number of ATTN messages per PF */ 1001 #define IGU_REG_STATISTIC_NUM_MESSAGE_SENT 0x130800 1002 /* [RW 32] Number of cycles the timer mask masking the IGU interrupt when a 1003 * timer mask command arrives. Value must be bigger than 100. */ 1004 #define IGU_REG_TIMER_MASKING_VALUE 0x13003c 1005 #define IGU_REG_TRAILING_EDGE_LATCH 0x130104 1006 #define IGU_REG_VF_CONFIGURATION 0x130170 1007 /* [WB_R 32] Each bit represent write done pending bits status for that SB 1008 * (MSI/MSIX message was sent and write done was not received yet). 0 = 1009 * clear; 1 = set. Data valid only in addresses 0-4. all the rest are zero. */ 1010 #define IGU_REG_WRITE_DONE_PENDING 0x130480 1011 #define MCP_A_REG_MCPR_SCRATCH 0x3a0000 1012 #define MCP_REG_MCPR_ACCESS_LOCK 0x8009c 1013 #define MCP_REG_MCPR_CPU_PROGRAM_COUNTER 0x8501c 1014 #define MCP_REG_MCPR_GP_INPUTS 0x800c0 1015 #define MCP_REG_MCPR_GP_OENABLE 0x800c8 1016 #define MCP_REG_MCPR_GP_OUTPUTS 0x800c4 1017 #define MCP_REG_MCPR_IMC_COMMAND 0x85900 1018 #define MCP_REG_MCPR_IMC_DATAREG0 0x85920 1019 #define MCP_REG_MCPR_IMC_SLAVE_CONTROL 0x85904 1020 #define MCP_REG_MCPR_CPU_PROGRAM_COUNTER 0x8501c 1021 #define MCP_REG_MCPR_NVM_ACCESS_ENABLE 0x86424 1022 #define MCP_REG_MCPR_NVM_ADDR 0x8640c 1023 #define MCP_REG_MCPR_NVM_CFG4 0x8642c 1024 #define MCP_REG_MCPR_NVM_COMMAND 0x86400 1025 #define MCP_REG_MCPR_NVM_READ 0x86410 1026 #define MCP_REG_MCPR_NVM_SW_ARB 0x86420 1027 #define MCP_REG_MCPR_NVM_WRITE 0x86408 1028 #define MCP_REG_MCPR_SCRATCH 0xa0000 1029 #define MISC_AEU_GENERAL_MASK_REG_AEU_NIG_CLOSE_MASK (0x1<<1) 1030 #define MISC_AEU_GENERAL_MASK_REG_AEU_PXP_CLOSE_MASK (0x1<<0) 1031 /* [R 32] read first 32 bit after inversion of function 0. mapped as 1032 follows: [0] NIG attention for function0; [1] NIG attention for 1033 function1; [2] GPIO1 mcp; [3] GPIO2 mcp; [4] GPIO3 mcp; [5] GPIO4 mcp; 1034 [6] GPIO1 function 1; [7] GPIO2 function 1; [8] GPIO3 function 1; [9] 1035 GPIO4 function 1; [10] PCIE glue/PXP VPD event function0; [11] PCIE 1036 glue/PXP VPD event function1; [12] PCIE glue/PXP Expansion ROM event0; 1037 [13] PCIE glue/PXP Expansion ROM event1; [14] SPIO4; [15] SPIO5; [16] 1038 MSI/X indication for mcp; [17] MSI/X indication for function 1; [18] BRB 1039 Parity error; [19] BRB Hw interrupt; [20] PRS Parity error; [21] PRS Hw 1040 interrupt; [22] SRC Parity error; [23] SRC Hw interrupt; [24] TSDM Parity 1041 error; [25] TSDM Hw interrupt; [26] TCM Parity error; [27] TCM Hw 1042 interrupt; [28] TSEMI Parity error; [29] TSEMI Hw interrupt; [30] PBF 1043 Parity error; [31] PBF Hw interrupt; */ 1044 #define MISC_REG_AEU_AFTER_INVERT_1_FUNC_0 0xa42c 1045 #define MISC_REG_AEU_AFTER_INVERT_1_FUNC_1 0xa430 1046 /* [R 32] read first 32 bit after inversion of mcp. mapped as follows: [0] 1047 NIG attention for function0; [1] NIG attention for function1; [2] GPIO1 1048 mcp; [3] GPIO2 mcp; [4] GPIO3 mcp; [5] GPIO4 mcp; [6] GPIO1 function 1; 1049 [7] GPIO2 function 1; [8] GPIO3 function 1; [9] GPIO4 function 1; [10] 1050 PCIE glue/PXP VPD event function0; [11] PCIE glue/PXP VPD event 1051 function1; [12] PCIE glue/PXP Expansion ROM event0; [13] PCIE glue/PXP 1052 Expansion ROM event1; [14] SPIO4; [15] SPIO5; [16] MSI/X indication for 1053 mcp; [17] MSI/X indication for function 1; [18] BRB Parity error; [19] 1054 BRB Hw interrupt; [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC 1055 Parity error; [23] SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw 1056 interrupt; [26] TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI 1057 Parity error; [29] TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw 1058 interrupt; */ 1059 #define MISC_REG_AEU_AFTER_INVERT_1_MCP 0xa434 1060 /* [R 32] read second 32 bit after inversion of function 0. mapped as 1061 follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM 1062 Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw 1063 interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity 1064 error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw 1065 interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14] 1066 NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error; 1067 [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw 1068 interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM 1069 Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI 1070 Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM 1071 Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw 1072 interrupt; */ 1073 #define MISC_REG_AEU_AFTER_INVERT_2_FUNC_0 0xa438 1074 #define MISC_REG_AEU_AFTER_INVERT_2_FUNC_1 0xa43c 1075 /* [R 32] read second 32 bit after inversion of mcp. mapped as follows: [0] 1076 PBClient Parity error; [1] PBClient Hw interrupt; [2] QM Parity error; 1077 [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw interrupt; 1078 [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity error; [9] 1079 XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw interrupt; [12] 1080 DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14] NIG Parity 1081 error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error; [17] Vaux 1082 PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw interrupt; 1083 [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM Parity error; 1084 [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI Hw interrupt; 1085 [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM Parity error; 1086 [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw interrupt; */ 1087 #define MISC_REG_AEU_AFTER_INVERT_2_MCP 0xa440 1088 /* [R 32] read third 32 bit after inversion of function 0. mapped as 1089 follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP Parity 1090 error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error; [5] 1091 PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw 1092 interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity 1093 error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC) 1094 Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16] 1095 pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20] 1096 MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23] 1097 SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW 1098 timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3 1099 func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General 1100 attn1; */ 1101 #define MISC_REG_AEU_AFTER_INVERT_3_FUNC_0 0xa444 1102 #define MISC_REG_AEU_AFTER_INVERT_3_FUNC_1 0xa448 1103 /* [R 32] read third 32 bit after inversion of mcp. mapped as follows: [0] 1104 CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP Parity error; [3] PXP 1105 Hw interrupt; [4] PXPpciClockClient Parity error; [5] PXPpciClockClient 1106 Hw interrupt; [6] CFC Parity error; [7] CFC Hw interrupt; [8] CDU Parity 1107 error; [9] CDU Hw interrupt; [10] DMAE Parity error; [11] DMAE Hw 1108 interrupt; [12] IGU (HC) Parity error; [13] IGU (HC) Hw interrupt; [14] 1109 MISC Parity error; [15] MISC Hw interrupt; [16] pxp_misc_mps_attn; [17] 1110 Flash event; [18] SMB event; [19] MCP attn0; [20] MCP attn1; [21] SW 1111 timers attn_1 func0; [22] SW timers attn_2 func0; [23] SW timers attn_3 1112 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW timers attn_1 1113 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3 func1; [29] SW 1114 timers attn_4 func1; [30] General attn0; [31] General attn1; */ 1115 #define MISC_REG_AEU_AFTER_INVERT_3_MCP 0xa44c 1116 /* [R 32] read fourth 32 bit after inversion of function 0. mapped as 1117 follows: [0] General attn2; [1] General attn3; [2] General attn4; [3] 1118 General attn5; [4] General attn6; [5] General attn7; [6] General attn8; 1119 [7] General attn9; [8] General attn10; [9] General attn11; [10] General 1120 attn12; [11] General attn13; [12] General attn14; [13] General attn15; 1121 [14] General attn16; [15] General attn17; [16] General attn18; [17] 1122 General attn19; [18] General attn20; [19] General attn21; [20] Main power 1123 interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN 1124 Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC 1125 Latched timeout attention; [27] GRC Latched reserved access attention; 1126 [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP 1127 Latched ump_tx_parity; [31] MCP Latched scpad_parity; */ 1128 #define MISC_REG_AEU_AFTER_INVERT_4_FUNC_0 0xa450 1129 #define MISC_REG_AEU_AFTER_INVERT_4_FUNC_1 0xa454 1130 /* [R 32] read fourth 32 bit after inversion of mcp. mapped as follows: [0] 1131 General attn2; [1] General attn3; [2] General attn4; [3] General attn5; 1132 [4] General attn6; [5] General attn7; [6] General attn8; [7] General 1133 attn9; [8] General attn10; [9] General attn11; [10] General attn12; [11] 1134 General attn13; [12] General attn14; [13] General attn15; [14] General 1135 attn16; [15] General attn17; [16] General attn18; [17] General attn19; 1136 [18] General attn20; [19] General attn21; [20] Main power interrupt; [21] 1137 RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN Latched attn; [24] 1138 RBCU Latched attn; [25] RBCP Latched attn; [26] GRC Latched timeout 1139 attention; [27] GRC Latched reserved access attention; [28] MCP Latched 1140 rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP Latched 1141 ump_tx_parity; [31] MCP Latched scpad_parity; */ 1142 #define MISC_REG_AEU_AFTER_INVERT_4_MCP 0xa458 1143 /* [R 32] Read fifth 32 bit after inversion of function 0. Mapped as 1144 * follows: [0] PGLUE config_space; [1] PGLUE misc_flr; [2] PGLUE B RBC 1145 * attention [3] PGLUE B RBC parity; [4] ATC attention; [5] ATC parity; [6] 1146 * CNIG attention (reserved); [7] CNIG parity (reserved); [31-8] Reserved; */ 1147 #define MISC_REG_AEU_AFTER_INVERT_5_FUNC_0 0xa700 1148 /* [W 14] write to this register results with the clear of the latched 1149 signals; one in d0 clears RBCR latch; one in d1 clears RBCT latch; one in 1150 d2 clears RBCN latch; one in d3 clears RBCU latch; one in d4 clears RBCP 1151 latch; one in d5 clears GRC Latched timeout attention; one in d6 clears 1152 GRC Latched reserved access attention; one in d7 clears Latched 1153 rom_parity; one in d8 clears Latched ump_rx_parity; one in d9 clears 1154 Latched ump_tx_parity; one in d10 clears Latched scpad_parity (both 1155 ports); one in d11 clears pxpv_misc_mps_attn; one in d12 clears 1156 pxp_misc_exp_rom_attn0; one in d13 clears pxp_misc_exp_rom_attn1; read 1157 from this register return zero */ 1158 #define MISC_REG_AEU_CLR_LATCH_SIGNAL 0xa45c 1159 /* [RW 32] first 32b for enabling the output for function 0 output0. mapped 1160 as follows: [0] NIG attention for function0; [1] NIG attention for 1161 function1; [2] GPIO1 function 0; [3] GPIO2 function 0; [4] GPIO3 function 1162 0; [5] GPIO4 function 0; [6] GPIO1 function 1; [7] GPIO2 function 1; [8] 1163 GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event 1164 function0; [11] PCIE glue/PXP VPD event function1; [12] PCIE glue/PXP 1165 Expansion ROM event0; [13] PCIE glue/PXP Expansion ROM event1; [14] 1166 SPIO4; [15] SPIO5; [16] MSI/X indication for function 0; [17] MSI/X 1167 indication for function 1; [18] BRB Parity error; [19] BRB Hw interrupt; 1168 [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC Parity error; [23] 1169 SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw interrupt; [26] 1170 TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI Parity error; [29] 1171 TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */ 1172 #define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0 0xa06c 1173 #define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_1 0xa07c 1174 #define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_2 0xa08c 1175 #define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_3 0xa09c 1176 #define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_5 0xa0bc 1177 #define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_6 0xa0cc 1178 #define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_7 0xa0dc 1179 /* [RW 32] first 32b for enabling the output for function 1 output0. mapped 1180 as follows: [0] NIG attention for function0; [1] NIG attention for 1181 function1; [2] GPIO1 function 1; [3] GPIO2 function 1; [4] GPIO3 function 1182 1; [5] GPIO4 function 1; [6] GPIO1 function 1; [7] GPIO2 function 1; [8] 1183 GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event 1184 function0; [11] PCIE glue/PXP VPD event function1; [12] PCIE glue/PXP 1185 Expansion ROM event0; [13] PCIE glue/PXP Expansion ROM event1; [14] 1186 SPIO4; [15] SPIO5; [16] MSI/X indication for function 1; [17] MSI/X 1187 indication for function 1; [18] BRB Parity error; [19] BRB Hw interrupt; 1188 [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC Parity error; [23] 1189 SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw interrupt; [26] 1190 TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI Parity error; [29] 1191 TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */ 1192 #define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 0xa10c 1193 #define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_1 0xa11c 1194 #define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_2 0xa12c 1195 #define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_3 0xa13c 1196 #define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_5 0xa15c 1197 #define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_6 0xa16c 1198 #define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_7 0xa17c 1199 /* [RW 32] first 32b for enabling the output for close the gate nig. mapped 1200 as follows: [0] NIG attention for function0; [1] NIG attention for 1201 function1; [2] GPIO1 function 0; [3] GPIO2 function 0; [4] GPIO3 function 1202 0; [5] GPIO4 function 0; [6] GPIO1 function 1; [7] GPIO2 function 1; [8] 1203 GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event 1204 function0; [11] PCIE glue/PXP VPD event function1; [12] PCIE glue/PXP 1205 Expansion ROM event0; [13] PCIE glue/PXP Expansion ROM event1; [14] 1206 SPIO4; [15] SPIO5; [16] MSI/X indication for function 0; [17] MSI/X 1207 indication for function 1; [18] BRB Parity error; [19] BRB Hw interrupt; 1208 [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC Parity error; [23] 1209 SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw interrupt; [26] 1210 TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI Parity error; [29] 1211 TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */ 1212 #define MISC_REG_AEU_ENABLE1_NIG_0 0xa0ec 1213 #define MISC_REG_AEU_ENABLE1_NIG_1 0xa18c 1214 /* [RW 32] first 32b for enabling the output for close the gate pxp. mapped 1215 as follows: [0] NIG attention for function0; [1] NIG attention for 1216 function1; [2] GPIO1 function 0; [3] GPIO2 function 0; [4] GPIO3 function 1217 0; [5] GPIO4 function 0; [6] GPIO1 function 1; [7] GPIO2 function 1; [8] 1218 GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event 1219 function0; [11] PCIE glue/PXP VPD event function1; [12] PCIE glue/PXP 1220 Expansion ROM event0; [13] PCIE glue/PXP Expansion ROM event1; [14] 1221 SPIO4; [15] SPIO5; [16] MSI/X indication for function 0; [17] MSI/X 1222 indication for function 1; [18] BRB Parity error; [19] BRB Hw interrupt; 1223 [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC Parity error; [23] 1224 SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw interrupt; [26] 1225 TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI Parity error; [29] 1226 TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */ 1227 #define MISC_REG_AEU_ENABLE1_PXP_0 0xa0fc 1228 #define MISC_REG_AEU_ENABLE1_PXP_1 0xa19c 1229 /* [RW 32] second 32b for enabling the output for function 0 output0. mapped 1230 as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM 1231 Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw 1232 interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity 1233 error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw 1234 interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14] 1235 NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error; 1236 [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw 1237 interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM 1238 Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI 1239 Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM 1240 Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw 1241 interrupt; */ 1242 #define MISC_REG_AEU_ENABLE2_FUNC_0_OUT_0 0xa070 1243 #define MISC_REG_AEU_ENABLE2_FUNC_0_OUT_1 0xa080 1244 /* [RW 32] second 32b for enabling the output for function 1 output0. mapped 1245 as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM 1246 Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw 1247 interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity 1248 error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw 1249 interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14] 1250 NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error; 1251 [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw 1252 interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM 1253 Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI 1254 Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM 1255 Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw 1256 interrupt; */ 1257 #define MISC_REG_AEU_ENABLE2_FUNC_1_OUT_0 0xa110 1258 #define MISC_REG_AEU_ENABLE2_FUNC_1_OUT_1 0xa120 1259 /* [RW 32] second 32b for enabling the output for close the gate nig. mapped 1260 as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM 1261 Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw 1262 interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity 1263 error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw 1264 interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14] 1265 NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error; 1266 [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw 1267 interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM 1268 Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI 1269 Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM 1270 Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw 1271 interrupt; */ 1272 #define MISC_REG_AEU_ENABLE2_NIG_0 0xa0f0 1273 #define MISC_REG_AEU_ENABLE2_NIG_1 0xa190 1274 /* [RW 32] second 32b for enabling the output for close the gate pxp. mapped 1275 as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM 1276 Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw 1277 interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity 1278 error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw 1279 interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14] 1280 NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error; 1281 [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw 1282 interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM 1283 Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI 1284 Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM 1285 Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw 1286 interrupt; */ 1287 #define MISC_REG_AEU_ENABLE2_PXP_0 0xa100 1288 #define MISC_REG_AEU_ENABLE2_PXP_1 0xa1a0 1289 /* [RW 32] third 32b for enabling the output for function 0 output0. mapped 1290 as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP 1291 Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error; 1292 [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw 1293 interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity 1294 error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC) 1295 Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16] 1296 pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20] 1297 MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23] 1298 SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW 1299 timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3 1300 func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General 1301 attn1; */ 1302 #define MISC_REG_AEU_ENABLE3_FUNC_0_OUT_0 0xa074 1303 #define MISC_REG_AEU_ENABLE3_FUNC_0_OUT_1 0xa084 1304 /* [RW 32] third 32b for enabling the output for function 1 output0. mapped 1305 as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP 1306 Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error; 1307 [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw 1308 interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity 1309 error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC) 1310 Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16] 1311 pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20] 1312 MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23] 1313 SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW 1314 timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3 1315 func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General 1316 attn1; */ 1317 #define MISC_REG_AEU_ENABLE3_FUNC_1_OUT_0 0xa114 1318 #define MISC_REG_AEU_ENABLE3_FUNC_1_OUT_1 0xa124 1319 /* [RW 32] third 32b for enabling the output for close the gate nig. mapped 1320 as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP 1321 Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error; 1322 [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw 1323 interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity 1324 error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC) 1325 Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16] 1326 pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20] 1327 MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23] 1328 SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW 1329 timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3 1330 func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General 1331 attn1; */ 1332 #define MISC_REG_AEU_ENABLE3_NIG_0 0xa0f4 1333 #define MISC_REG_AEU_ENABLE3_NIG_1 0xa194 1334 /* [RW 32] third 32b for enabling the output for close the gate pxp. mapped 1335 as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP 1336 Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error; 1337 [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw 1338 interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity 1339 error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC) 1340 Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16] 1341 pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20] 1342 MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23] 1343 SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW 1344 timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3 1345 func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General 1346 attn1; */ 1347 #define MISC_REG_AEU_ENABLE3_PXP_0 0xa104 1348 #define MISC_REG_AEU_ENABLE3_PXP_1 0xa1a4 1349 /* [RW 32] fourth 32b for enabling the output for function 0 output0.mapped 1350 as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3] 1351 General attn5; [4] General attn6; [5] General attn7; [6] General attn8; 1352 [7] General attn9; [8] General attn10; [9] General attn11; [10] General 1353 attn12; [11] General attn13; [12] General attn14; [13] General attn15; 1354 [14] General attn16; [15] General attn17; [16] General attn18; [17] 1355 General attn19; [18] General attn20; [19] General attn21; [20] Main power 1356 interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN 1357 Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC 1358 Latched timeout attention; [27] GRC Latched reserved access attention; 1359 [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP 1360 Latched ump_tx_parity; [31] MCP Latched scpad_parity; */ 1361 #define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_0 0xa078 1362 #define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_2 0xa098 1363 #define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_4 0xa0b8 1364 #define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_5 0xa0c8 1365 #define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_6 0xa0d8 1366 #define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_7 0xa0e8 1367 /* [RW 32] fourth 32b for enabling the output for function 1 output0.mapped 1368 as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3] 1369 General attn5; [4] General attn6; [5] General attn7; [6] General attn8; 1370 [7] General attn9; [8] General attn10; [9] General attn11; [10] General 1371 attn12; [11] General attn13; [12] General attn14; [13] General attn15; 1372 [14] General attn16; [15] General attn17; [16] General attn18; [17] 1373 General attn19; [18] General attn20; [19] General attn21; [20] Main power 1374 interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN 1375 Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC 1376 Latched timeout attention; [27] GRC Latched reserved access attention; 1377 [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP 1378 Latched ump_tx_parity; [31] MCP Latched scpad_parity; */ 1379 #define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_0 0xa118 1380 #define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_2 0xa138 1381 #define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_4 0xa158 1382 #define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_5 0xa168 1383 #define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_6 0xa178 1384 #define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_7 0xa188 1385 /* [RW 32] fourth 32b for enabling the output for close the gate nig.mapped 1386 as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3] 1387 General attn5; [4] General attn6; [5] General attn7; [6] General attn8; 1388 [7] General attn9; [8] General attn10; [9] General attn11; [10] General 1389 attn12; [11] General attn13; [12] General attn14; [13] General attn15; 1390 [14] General attn16; [15] General attn17; [16] General attn18; [17] 1391 General attn19; [18] General attn20; [19] General attn21; [20] Main power 1392 interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN 1393 Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC 1394 Latched timeout attention; [27] GRC Latched reserved access attention; 1395 [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP 1396 Latched ump_tx_parity; [31] MCP Latched scpad_parity; */ 1397 #define MISC_REG_AEU_ENABLE4_NIG_0 0xa0f8 1398 #define MISC_REG_AEU_ENABLE4_NIG_1 0xa198 1399 /* [RW 32] fourth 32b for enabling the output for close the gate pxp.mapped 1400 as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3] 1401 General attn5; [4] General attn6; [5] General attn7; [6] General attn8; 1402 [7] General attn9; [8] General attn10; [9] General attn11; [10] General 1403 attn12; [11] General attn13; [12] General attn14; [13] General attn15; 1404 [14] General attn16; [15] General attn17; [16] General attn18; [17] 1405 General attn19; [18] General attn20; [19] General attn21; [20] Main power 1406 interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN 1407 Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC 1408 Latched timeout attention; [27] GRC Latched reserved access attention; 1409 [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP 1410 Latched ump_tx_parity; [31] MCP Latched scpad_parity; */ 1411 #define MISC_REG_AEU_ENABLE4_PXP_0 0xa108 1412 #define MISC_REG_AEU_ENABLE4_PXP_1 0xa1a8 1413 /* [RW 32] fifth 32b for enabling the output for function 0 output0. Mapped 1414 * as follows: [0] PGLUE config_space; [1] PGLUE misc_flr; [2] PGLUE B RBC 1415 * attention [3] PGLUE B RBC parity; [4] ATC attention; [5] ATC parity; [6] 1416 * mstat0 attention; [7] mstat0 parity; [8] mstat1 attention; [9] mstat1 1417 * parity; [31-10] Reserved; */ 1418 #define MISC_REG_AEU_ENABLE5_FUNC_0_OUT_0 0xa688 1419 /* [RW 32] Fifth 32b for enabling the output for function 1 output0. Mapped 1420 * as follows: [0] PGLUE config_space; [1] PGLUE misc_flr; [2] PGLUE B RBC 1421 * attention [3] PGLUE B RBC parity; [4] ATC attention; [5] ATC parity; [6] 1422 * mstat0 attention; [7] mstat0 parity; [8] mstat1 attention; [9] mstat1 1423 * parity; [31-10] Reserved; */ 1424 #define MISC_REG_AEU_ENABLE5_FUNC_1_OUT_0 0xa6b0 1425 /* [RW 1] set/clr general attention 0; this will set/clr bit 94 in the aeu 1426 128 bit vector */ 1427 #define MISC_REG_AEU_GENERAL_ATTN_0 0xa000 1428 #define MISC_REG_AEU_GENERAL_ATTN_1 0xa004 1429 #define MISC_REG_AEU_GENERAL_ATTN_10 0xa028 1430 #define MISC_REG_AEU_GENERAL_ATTN_11 0xa02c 1431 #define MISC_REG_AEU_GENERAL_ATTN_12 0xa030 1432 #define MISC_REG_AEU_GENERAL_ATTN_2 0xa008 1433 #define MISC_REG_AEU_GENERAL_ATTN_3 0xa00c 1434 #define MISC_REG_AEU_GENERAL_ATTN_4 0xa010 1435 #define MISC_REG_AEU_GENERAL_ATTN_5 0xa014 1436 #define MISC_REG_AEU_GENERAL_ATTN_6 0xa018 1437 #define MISC_REG_AEU_GENERAL_ATTN_7 0xa01c 1438 #define MISC_REG_AEU_GENERAL_ATTN_8 0xa020 1439 #define MISC_REG_AEU_GENERAL_ATTN_9 0xa024 1440 #define MISC_REG_AEU_GENERAL_MASK 0xa61c 1441 /* [RW 32] first 32b for inverting the input for function 0; for each bit: 1442 0= do not invert; 1= invert; mapped as follows: [0] NIG attention for 1443 function0; [1] NIG attention for function1; [2] GPIO1 mcp; [3] GPIO2 mcp; 1444 [4] GPIO3 mcp; [5] GPIO4 mcp; [6] GPIO1 function 1; [7] GPIO2 function 1; 1445 [8] GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event 1446 function0; [11] PCIE glue/PXP VPD event function1; [12] PCIE glue/PXP 1447 Expansion ROM event0; [13] PCIE glue/PXP Expansion ROM event1; [14] 1448 SPIO4; [15] SPIO5; [16] MSI/X indication for mcp; [17] MSI/X indication 1449 for function 1; [18] BRB Parity error; [19] BRB Hw interrupt; [20] PRS 1450 Parity error; [21] PRS Hw interrupt; [22] SRC Parity error; [23] SRC Hw 1451 interrupt; [24] TSDM Parity error; [25] TSDM Hw interrupt; [26] TCM 1452 Parity error; [27] TCM Hw interrupt; [28] TSEMI Parity error; [29] TSEMI 1453 Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */ 1454 #define MISC_REG_AEU_INVERTER_1_FUNC_0 0xa22c 1455 #define MISC_REG_AEU_INVERTER_1_FUNC_1 0xa23c 1456 /* [RW 32] second 32b for inverting the input for function 0; for each bit: 1457 0= do not invert; 1= invert. mapped as follows: [0] PBClient Parity 1458 error; [1] PBClient Hw interrupt; [2] QM Parity error; [3] QM Hw 1459 interrupt; [4] Timers Parity error; [5] Timers Hw interrupt; [6] XSDM 1460 Parity error; [7] XSDM Hw interrupt; [8] XCM Parity error; [9] XCM Hw 1461 interrupt; [10] XSEMI Parity error; [11] XSEMI Hw interrupt; [12] 1462 DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14] NIG Parity 1463 error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error; [17] Vaux 1464 PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw interrupt; 1465 [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM Parity error; 1466 [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI Hw interrupt; 1467 [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM Parity error; 1468 [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw interrupt; */ 1469 #define MISC_REG_AEU_INVERTER_2_FUNC_0 0xa230 1470 #define MISC_REG_AEU_INVERTER_2_FUNC_1 0xa240 1471 /* [RW 10] [7:0] = mask 8 attention output signals toward IGU function0; 1472 [9:8] = raserved. Zero = mask; one = unmask */ 1473 #define MISC_REG_AEU_MASK_ATTN_FUNC_0 0xa060 1474 #define MISC_REG_AEU_MASK_ATTN_FUNC_1 0xa064 1475 /* [RW 1] If set a system kill occurred */ 1476 #define MISC_REG_AEU_SYS_KILL_OCCURRED 0xa610 1477 /* [RW 32] Represent the status of the input vector to the AEU when a system 1478 kill occurred. The register is reset in por reset. Mapped as follows: [0] 1479 NIG attention for function0; [1] NIG attention for function1; [2] GPIO1 1480 mcp; [3] GPIO2 mcp; [4] GPIO3 mcp; [5] GPIO4 mcp; [6] GPIO1 function 1; 1481 [7] GPIO2 function 1; [8] GPIO3 function 1; [9] GPIO4 function 1; [10] 1482 PCIE glue/PXP VPD event function0; [11] PCIE glue/PXP VPD event 1483 function1; [12] PCIE glue/PXP Expansion ROM event0; [13] PCIE glue/PXP 1484 Expansion ROM event1; [14] SPIO4; [15] SPIO5; [16] MSI/X indication for 1485 mcp; [17] MSI/X indication for function 1; [18] BRB Parity error; [19] 1486 BRB Hw interrupt; [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC 1487 Parity error; [23] SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw 1488 interrupt; [26] TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI 1489 Parity error; [29] TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw 1490 interrupt; */ 1491 #define MISC_REG_AEU_SYS_KILL_STATUS_0 0xa600 1492 #define MISC_REG_AEU_SYS_KILL_STATUS_1 0xa604 1493 #define MISC_REG_AEU_SYS_KILL_STATUS_2 0xa608 1494 #define MISC_REG_AEU_SYS_KILL_STATUS_3 0xa60c 1495 /* [R 4] This field indicates the type of the device. '0' - 2 Ports; '1' - 1 1496 Port. */ 1497 #define MISC_REG_BOND_ID 0xa400 1498 /* [R 16] These bits indicate the part number for the chip. */ 1499 #define MISC_REG_CHIP_NUM 0xa408 1500 /* [R 4] These bits indicate the base revision of the chip. This value 1501 starts at 0x0 for the A0 tape-out and increments by one for each 1502 all-layer tape-out. */ 1503 #define MISC_REG_CHIP_REV 0xa40c 1504 /* [R 14] otp_misc_do[100:0] spare bits collection: 13:11- 1505 * otp_misc_do[100:98]; 10:7 - otp_misc_do[87:84]; 6:3 - otp_misc_do[75:72]; 1506 * 2:1 - otp_misc_do[51:50]; 0 - otp_misc_do[1]. */ 1507 #define MISC_REG_CHIP_TYPE 0xac60 1508 #define MISC_REG_CHIP_TYPE_57811_MASK (1<<1) 1509 #define MISC_REG_CPMU_LP_DR_ENABLE 0xa858 1510 /* [RW 1] FW EEE LPI Enable. When 1 indicates that EEE LPI mode is enabled 1511 * by FW. When 0 indicates that the EEE LPI mode is disabled by FW. Clk 1512 * 25MHz. Reset on hard reset. */ 1513 #define MISC_REG_CPMU_LP_FW_ENABLE_P0 0xa84c 1514 /* [RW 32] EEE LPI Idle Threshold. The threshold value for the idle EEE LPI 1515 * counter. Timer tick is 1 us. Clock 25MHz. Reset on hard reset. */ 1516 #define MISC_REG_CPMU_LP_IDLE_THR_P0 0xa8a0 1517 /* [RW 18] LPI entry events mask. [0] - Vmain SM Mask. When 1 indicates that 1518 * the Vmain SM end state is disabled. When 0 indicates that the Vmain SM 1519 * end state is enabled. [1] - FW Queues Empty Mask. When 1 indicates that 1520 * the FW command that all Queues are empty is disabled. When 0 indicates 1521 * that the FW command that all Queues are empty is enabled. [2] - FW Early 1522 * Exit Mask / Reserved (Entry mask). When 1 indicates that the FW Early 1523 * Exit command is disabled. When 0 indicates that the FW Early Exit command 1524 * is enabled. This bit applicable only in the EXIT Events Mask registers. 1525 * [3] - PBF Request Mask. When 1 indicates that the PBF Request indication 1526 * is disabled. When 0 indicates that the PBF Request indication is enabled. 1527 * [4] - Tx Request Mask. When =1 indicates that the Tx other Than PBF 1528 * Request indication is disabled. When 0 indicates that the Tx Other Than 1529 * PBF Request indication is enabled. [5] - Rx EEE LPI Status Mask. When 1 1530 * indicates that the RX EEE LPI Status indication is disabled. When 0 1531 * indicates that the RX EEE LPI Status indication is enabled. In the EXIT 1532 * Events Masks registers; this bit masks the falling edge detect of the LPI 1533 * Status (Rx LPI is on - off). [6] - Tx Pause Mask. When 1 indicates that 1534 * the Tx Pause indication is disabled. When 0 indicates that the Tx Pause 1535 * indication is enabled. [7] - BRB1 Empty Mask. When 1 indicates that the 1536 * BRB1 EMPTY indication is disabled. When 0 indicates that the BRB1 EMPTY 1537 * indication is enabled. [8] - QM Idle Mask. When 1 indicates that the QM 1538 * IDLE indication is disabled. When 0 indicates that the QM IDLE indication 1539 * is enabled. (One bit for both VOQ0 and VOQ1). [9] - QM LB Idle Mask. When 1540 * 1 indicates that the QM IDLE indication for LOOPBACK is disabled. When 0 1541 * indicates that the QM IDLE indication for LOOPBACK is enabled. [10] - L1 1542 * Status Mask. When 1 indicates that the L1 Status indication from the PCIE 1543 * CORE is disabled. When 0 indicates that the RX EEE LPI Status indication 1544 * from the PCIE CORE is enabled. In the EXIT Events Masks registers; this 1545 * bit masks the falling edge detect of the L1 status (L1 is on - off). [11] 1546 * - P0 E0 EEE EEE LPI REQ Mask. When =1 indicates that the P0 E0 EEE EEE 1547 * LPI REQ indication is disabled. When =0 indicates that the P0 E0 EEE LPI 1548 * REQ indication is enabled. [12] - P1 E0 EEE LPI REQ Mask. When =1 1549 * indicates that the P0 EEE LPI REQ indication is disabled. When =0 1550 * indicates that the P0 EEE LPI REQ indication is enabled. [13] - P0 E1 EEE 1551 * LPI REQ Mask. When =1 indicates that the P0 EEE LPI REQ indication is 1552 * disabled. When =0 indicates that the P0 EEE LPI REQ indication is 1553 * enabled. [14] - P1 E1 EEE LPI REQ Mask. When =1 indicates that the P0 EEE 1554 * LPI REQ indication is disabled. When =0 indicates that the P0 EEE LPI REQ 1555 * indication is enabled. [15] - L1 REQ Mask. When =1 indicates that the L1 1556 * REQ indication is disabled. When =0 indicates that the L1 indication is 1557 * enabled. [16] - Rx EEE LPI Status Edge Detect Mask. When =1 indicates 1558 * that the RX EEE LPI Status Falling Edge Detect indication is disabled (Rx 1559 * EEE LPI is on - off). When =0 indicates that the RX EEE LPI Status 1560 * Falling Edge Detec indication is enabled (Rx EEE LPI is on - off). This 1561 * bit is applicable only in the EXIT Events Masks registers. [17] - L1 1562 * Status Edge Detect Mask. When =1 indicates that the L1 Status Falling 1563 * Edge Detect indication from the PCIE CORE is disabled (L1 is on - off). 1564 * When =0 indicates that the L1 Status Falling Edge Detect indication from 1565 * the PCIE CORE is enabled (L1 is on - off). This bit is applicable only in 1566 * the EXIT Events Masks registers. Clock 25MHz. Reset on hard reset. */ 1567 #define MISC_REG_CPMU_LP_MASK_ENT_P0 0xa880 1568 /* [RW 18] EEE LPI exit events mask. [0] - Vmain SM Mask. When 1 indicates 1569 * that the Vmain SM end state is disabled. When 0 indicates that the Vmain 1570 * SM end state is enabled. [1] - FW Queues Empty Mask. When 1 indicates 1571 * that the FW command that all Queues are empty is disabled. When 0 1572 * indicates that the FW command that all Queues are empty is enabled. [2] - 1573 * FW Early Exit Mask / Reserved (Entry mask). When 1 indicates that the FW 1574 * Early Exit command is disabled. When 0 indicates that the FW Early Exit 1575 * command is enabled. This bit applicable only in the EXIT Events Mask 1576 * registers. [3] - PBF Request Mask. When 1 indicates that the PBF Request 1577 * indication is disabled. When 0 indicates that the PBF Request indication 1578 * is enabled. [4] - Tx Request Mask. When =1 indicates that the Tx other 1579 * Than PBF Request indication is disabled. When 0 indicates that the Tx 1580 * Other Than PBF Request indication is enabled. [5] - Rx EEE LPI Status 1581 * Mask. When 1 indicates that the RX EEE LPI Status indication is disabled. 1582 * When 0 indicates that the RX LPI Status indication is enabled. In the 1583 * EXIT Events Masks registers; this bit masks the falling edge detect of 1584 * the EEE LPI Status (Rx EEE LPI is on - off). [6] - Tx Pause Mask. When 1 1585 * indicates that the Tx Pause indication is disabled. When 0 indicates that 1586 * the Tx Pause indication is enabled. [7] - BRB1 Empty Mask. When 1 1587 * indicates that the BRB1 EMPTY indication is disabled. When 0 indicates 1588 * that the BRB1 EMPTY indication is enabled. [8] - QM Idle Mask. When 1 1589 * indicates that the QM IDLE indication is disabled. When 0 indicates that 1590 * the QM IDLE indication is enabled. (One bit for both VOQ0 and VOQ1). [9] 1591 * - QM LB Idle Mask. When 1 indicates that the QM IDLE indication for 1592 * LOOPBACK is disabled. When 0 indicates that the QM IDLE indication for 1593 * LOOPBACK is enabled. [10] - L1 Status Mask. When 1 indicates that the L1 1594 * Status indication from the PCIE CORE is disabled. When 0 indicates that 1595 * the RX EEE LPI Status indication from the PCIE CORE is enabled. In the 1596 * EXIT Events Masks registers; this bit masks the falling edge detect of 1597 * the L1 status (L1 is on - off). [11] - P0 E0 EEE EEE LPI REQ Mask. When 1598 * =1 indicates that the P0 E0 EEE EEE LPI REQ indication is disabled. When 1599 * =0 indicates that the P0 E0 EEE LPI REQ indication is enabled. [12] - P1 1600 * E0 EEE LPI REQ Mask. When =1 indicates that the P0 EEE LPI REQ indication 1601 * is disabled. When =0 indicates that the P0 EEE LPI REQ indication is 1602 * enabled. [13] - P0 E1 EEE LPI REQ Mask. When =1 indicates that the P0 EEE 1603 * LPI REQ indication is disabled. When =0 indicates that the P0 EEE LPI REQ 1604 * indication is enabled. [14] - P1 E1 EEE LPI REQ Mask. When =1 indicates 1605 * that the P0 EEE LPI REQ indication is disabled. When =0 indicates that 1606 * the P0 EEE LPI REQ indication is enabled. [15] - L1 REQ Mask. When =1 1607 * indicates that the L1 REQ indication is disabled. When =0 indicates that 1608 * the L1 indication is enabled. [16] - Rx EEE LPI Status Edge Detect Mask. 1609 * When =1 indicates that the RX EEE LPI Status Falling Edge Detect 1610 * indication is disabled (Rx EEE LPI is on - off). When =0 indicates that 1611 * the RX EEE LPI Status Falling Edge Detec indication is enabled (Rx EEE 1612 * LPI is on - off). This bit is applicable only in the EXIT Events Masks 1613 * registers. [17] - L1 Status Edge Detect Mask. When =1 indicates that the 1614 * L1 Status Falling Edge Detect indication from the PCIE CORE is disabled 1615 * (L1 is on - off). When =0 indicates that the L1 Status Falling Edge 1616 * Detect indication from the PCIE CORE is enabled (L1 is on - off). This 1617 * bit is applicable only in the EXIT Events Masks registers.Clock 25MHz. 1618 * Reset on hard reset. */ 1619 #define MISC_REG_CPMU_LP_MASK_EXT_P0 0xa888 1620 /* [RW 16] EEE LPI Entry Events Counter. A statistic counter with the number 1621 * of counts that the SM entered the EEE LPI state. Clock 25MHz. Read only 1622 * register. Reset on hard reset. */ 1623 #define MISC_REG_CPMU_LP_SM_ENT_CNT_P0 0xa8b8 1624 /* [RW 16] EEE LPI Entry Events Counter. A statistic counter with the number 1625 * of counts that the SM entered the EEE LPI state. Clock 25MHz. Read only 1626 * register. Reset on hard reset. */ 1627 #define MISC_REG_CPMU_LP_SM_ENT_CNT_P1 0xa8bc 1628 /* [RW 32] The following driver registers(1...16) represent 16 drivers and 1629 32 clients. Each client can be controlled by one driver only. One in each 1630 bit represent that this driver control the appropriate client (Ex: bit 5 1631 is set means this driver control client number 5). addr1 = set; addr0 = 1632 clear; read from both addresses will give the same result = status. write 1633 to address 1 will set a request to control all the clients that their 1634 appropriate bit (in the write command) is set. if the client is free (the 1635 appropriate bit in all the other drivers is clear) one will be written to 1636 that driver register; if the client isn't free the bit will remain zero. 1637 if the appropriate bit is set (the driver request to gain control on a 1638 client it already controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW 1639 interrupt will be asserted). write to address 0 will set a request to 1640 free all the clients that their appropriate bit (in the write command) is 1641 set. if the appropriate bit is clear (the driver request to free a client 1642 it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will 1643 be asserted). */ 1644 #define MISC_REG_DRIVER_CONTROL_1 0xa510 1645 #define MISC_REG_DRIVER_CONTROL_7 0xa3c8 1646 /* [RW 1] e1hmf for WOL. If clr WOL signal o the PXP will be send on bit 0 1647 only. */ 1648 #define MISC_REG_E1HMF_MODE 0xa5f8 1649 /* [R 1] Status of four port mode path swap input pin. */ 1650 #define MISC_REG_FOUR_PORT_PATH_SWAP 0xa75c 1651 /* [RW 2] 4 port path swap overwrite.[0] - Overwrite control; if it is 0 - 1652 the path_swap output is equal to 4 port mode path swap input pin; if it 1653 is 1 - the path_swap output is equal to bit[1] of this register; [1] - 1654 Overwrite value. If bit[0] of this register is 1 this is the value that 1655 receives the path_swap output. Reset on Hard reset. */ 1656 #define MISC_REG_FOUR_PORT_PATH_SWAP_OVWR 0xa738 1657 /* [R 1] Status of 4 port mode port swap input pin. */ 1658 #define MISC_REG_FOUR_PORT_PORT_SWAP 0xa754 1659 /* [RW 2] 4 port port swap overwrite.[0] - Overwrite control; if it is 0 - 1660 the port_swap output is equal to 4 port mode port swap input pin; if it 1661 is 1 - the port_swap output is equal to bit[1] of this register; [1] - 1662 Overwrite value. If bit[0] of this register is 1 this is the value that 1663 receives the port_swap output. Reset on Hard reset. */ 1664 #define MISC_REG_FOUR_PORT_PORT_SWAP_OVWR 0xa734 1665 /* [RW 32] Debug only: spare RW register reset by core reset */ 1666 #define MISC_REG_GENERIC_CR_0 0xa460 1667 #define MISC_REG_GENERIC_CR_1 0xa464 1668 /* [RW 32] Debug only: spare RW register reset by por reset */ 1669 #define MISC_REG_GENERIC_POR_1 0xa474 1670 /* [RW 32] Bit[0]: EPIO MODE SEL: Setting this bit to 1 will allow SW/FW to 1671 use all of the 32 Extended GPIO pins. Without setting this bit; an EPIO 1672 can not be configured as an output. Each output has its output enable in 1673 the MCP register space; but this bit needs to be set to make use of that. 1674 Bit[3:1] spare. Bit[4]: WCVTMON_PWRDN: Powerdown for Warpcore VTMON. When 1675 set to 1 - Powerdown. Bit[5]: WCVTMON_RESETB: Reset for Warpcore VTMON. 1676 When set to 0 - vTMON is in reset. Bit[6]: setting this bit will change 1677 the i/o to an output and will drive the TimeSync output. Bit[31:7]: 1678 spare. Global register. Reset by hard reset. */ 1679 #define MISC_REG_GEN_PURP_HWG 0xa9a0 1680 /* [RW 32] GPIO. [31-28] FLOAT port 0; [27-24] FLOAT port 0; When any of 1681 these bits is written as a '1'; the corresponding SPIO bit will turn off 1682 it's drivers and become an input. This is the reset state of all GPIO 1683 pins. The read value of these bits will be a '1' if that last command 1684 (#SET; #CLR; or #FLOAT) for this bit was a #FLOAT. (reset value 0xff). 1685 [23-20] CLR port 1; 19-16] CLR port 0; When any of these bits is written 1686 as a '1'; the corresponding GPIO bit will drive low. The read value of 1687 these bits will be a '1' if that last command (#SET; #CLR; or #FLOAT) for 1688 this bit was a #CLR. (reset value 0). [15-12] SET port 1; 11-8] port 0; 1689 SET When any of these bits is written as a '1'; the corresponding GPIO 1690 bit will drive high (if it has that capability). The read value of these 1691 bits will be a '1' if that last command (#SET; #CLR; or #FLOAT) for this 1692 bit was a #SET. (reset value 0). [7-4] VALUE port 1; [3-0] VALUE port 0; 1693 RO; These bits indicate the read value of each of the eight GPIO pins. 1694 This is the result value of the pin; not the drive value. Writing these 1695 bits will have not effect. */ 1696 #define MISC_REG_GPIO 0xa490 1697 /* [RW 8] These bits enable the GPIO_INTs to signals event to the 1698 IGU/MCP.according to the following map: [0] p0_gpio_0; [1] p0_gpio_1; [2] 1699 p0_gpio_2; [3] p0_gpio_3; [4] p1_gpio_0; [5] p1_gpio_1; [6] p1_gpio_2; 1700 [7] p1_gpio_3; */ 1701 #define MISC_REG_GPIO_EVENT_EN 0xa2bc 1702 /* [RW 32] GPIO INT. [31-28] OLD_CLR port1; [27-24] OLD_CLR port0; Writing a 1703 '1' to these bit clears the corresponding bit in the #OLD_VALUE register. 1704 This will acknowledge an interrupt on the falling edge of corresponding 1705 GPIO input (reset value 0). [23-16] OLD_SET [23-16] port1; OLD_SET port0; 1706 Writing a '1' to these bit sets the corresponding bit in the #OLD_VALUE 1707 register. This will acknowledge an interrupt on the rising edge of 1708 corresponding SPIO input (reset value 0). [15-12] OLD_VALUE [11-8] port1; 1709 OLD_VALUE port0; RO; These bits indicate the old value of the GPIO input 1710 value. When the ~INT_STATE bit is set; this bit indicates the OLD value 1711 of the pin such that if ~INT_STATE is set and this bit is '0'; then the 1712 interrupt is due to a low to high edge. If ~INT_STATE is set and this bit 1713 is '1'; then the interrupt is due to a high to low edge (reset value 0). 1714 [7-4] INT_STATE port1; [3-0] INT_STATE RO port0; These bits indicate the 1715 current GPIO interrupt state for each GPIO pin. This bit is cleared when 1716 the appropriate #OLD_SET or #OLD_CLR command bit is written. This bit is 1717 set when the GPIO input does not match the current value in #OLD_VALUE 1718 (reset value 0). */ 1719 #define MISC_REG_GPIO_INT 0xa494 1720 /* [R 28] this field hold the last information that caused reserved 1721 attention. bits [19:0] - address; [22:20] function; [23] reserved; 1722 [27:24] the master that caused the attention - according to the following 1723 encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 = 1724 dbu; 8 = dmae */ 1725 #define MISC_REG_GRC_RSV_ATTN 0xa3c0 1726 /* [R 28] this field hold the last information that caused timeout 1727 attention. bits [19:0] - address; [22:20] function; [23] reserved; 1728 [27:24] the master that caused the attention - according to the following 1729 encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 = 1730 dbu; 8 = dmae */ 1731 #define MISC_REG_GRC_TIMEOUT_ATTN 0xa3c4 1732 /* [RW 1] Setting this bit enables a timer in the GRC block to timeout any 1733 access that does not finish within 1734 ~misc_registers_grc_timout_val.grc_timeout_val cycles. When this bit is 1735 cleared; this timeout is disabled. If this timeout occurs; the GRC shall 1736 assert it attention output. */ 1737 #define MISC_REG_GRC_TIMEOUT_EN 0xa280 1738 /* [RW 28] 28 LSB of LCPLL first register; reset val = 521. inside order of 1739 the bits is: [2:0] OAC reset value 001) CML output buffer bias control; 1740 111 for +40%; 011 for +20%; 001 for 0%; 000 for -20%. [5:3] Icp_ctrl 1741 (reset value 001) Charge pump current control; 111 for 720u; 011 for 1742 600u; 001 for 480u and 000 for 360u. [7:6] Bias_ctrl (reset value 00) 1743 Global bias control; When bit 7 is high bias current will be 10 0gh; When 1744 bit 6 is high bias will be 100w; Valid values are 00; 10; 01. [10:8] 1745 Pll_observe (reset value 010) Bits to control observability. bit 10 is 1746 for test bias; bit 9 is for test CK; bit 8 is test Vc. [12:11] Vth_ctrl 1747 (reset value 00) Comparator threshold control. 00 for 0.6V; 01 for 0.54V 1748 and 10 for 0.66V. [13] pllSeqStart (reset value 0) Enables VCO tuning 1749 sequencer: 1= sequencer disabled; 0= sequencer enabled (inverted 1750 internally). [14] reserved (reset value 0) Reset for VCO sequencer is 1751 connected to RESET input directly. [15] capRetry_en (reset value 0) 1752 enable retry on cap search failure (inverted). [16] freqMonitor_e (reset 1753 value 0) bit to continuously monitor vco freq (inverted). [17] 1754 freqDetRestart_en (reset value 0) bit to enable restart when not freq 1755 locked (inverted). [18] freqDetRetry_en (reset value 0) bit to enable 1756 retry on freq det failure(inverted). [19] pllForceFdone_en (reset value 1757 0) bit to enable pllForceFdone & pllForceFpass into pllSeq. [20] 1758 pllForceFdone (reset value 0) bit to force freqDone. [21] pllForceFpass 1759 (reset value 0) bit to force freqPass. [22] pllForceDone_en (reset value 1760 0) bit to enable pllForceCapDone. [23] pllForceCapDone (reset value 0) 1761 bit to force capDone. [24] pllForceCapPass_en (reset value 0) bit to 1762 enable pllForceCapPass. [25] pllForceCapPass (reset value 0) bit to force 1763 capPass. [26] capRestart (reset value 0) bit to force cap sequencer to 1764 restart. [27] capSelectM_en (reset value 0) bit to enable cap select 1765 register bits. */ 1766 #define MISC_REG_LCPLL_CTRL_1 0xa2a4 1767 #define MISC_REG_LCPLL_CTRL_REG_2 0xa2a8 1768 /* [RW 1] LCPLL power down. Global register. Active High. Reset on POR 1769 * reset. */ 1770 #define MISC_REG_LCPLL_E40_PWRDWN 0xaa74 1771 /* [RW 1] LCPLL VCO reset. Global register. Active Low Reset on POR reset. */ 1772 #define MISC_REG_LCPLL_E40_RESETB_ANA 0xaa78 1773 /* [RW 1] LCPLL post-divider reset. Global register. Active Low Reset on POR 1774 * reset. */ 1775 #define MISC_REG_LCPLL_E40_RESETB_DIG 0xaa7c 1776 /* [RW 4] Interrupt mask register #0 read/write */ 1777 #define MISC_REG_MISC_INT_MASK 0xa388 1778 /* [RW 1] Parity mask register #0 read/write */ 1779 #define MISC_REG_MISC_PRTY_MASK 0xa398 1780 /* [R 1] Parity register #0 read */ 1781 #define MISC_REG_MISC_PRTY_STS 0xa38c 1782 /* [RC 1] Parity register #0 read clear */ 1783 #define MISC_REG_MISC_PRTY_STS_CLR 0xa390 1784 #define MISC_REG_NIG_WOL_P0 0xa270 1785 #define MISC_REG_NIG_WOL_P1 0xa274 1786 /* [R 1] If set indicate that the pcie_rst_b was asserted without perst 1787 assertion */ 1788 #define MISC_REG_PCIE_HOT_RESET 0xa618 1789 /* [RW 32] 32 LSB of storm PLL first register; reset val = 0x 071d2911. 1790 inside order of the bits is: [0] P1 divider[0] (reset value 1); [1] P1 1791 divider[1] (reset value 0); [2] P1 divider[2] (reset value 0); [3] P1 1792 divider[3] (reset value 0); [4] P2 divider[0] (reset value 1); [5] P2 1793 divider[1] (reset value 0); [6] P2 divider[2] (reset value 0); [7] P2 1794 divider[3] (reset value 0); [8] ph_det_dis (reset value 1); [9] 1795 freq_det_dis (reset value 0); [10] Icpx[0] (reset value 0); [11] Icpx[1] 1796 (reset value 1); [12] Icpx[2] (reset value 0); [13] Icpx[3] (reset value 1797 1); [14] Icpx[4] (reset value 0); [15] Icpx[5] (reset value 0); [16] 1798 Rx[0] (reset value 1); [17] Rx[1] (reset value 0); [18] vc_en (reset 1799 value 1); [19] vco_rng[0] (reset value 1); [20] vco_rng[1] (reset value 1800 1); [21] Kvco_xf[0] (reset value 0); [22] Kvco_xf[1] (reset value 0); 1801 [23] Kvco_xf[2] (reset value 0); [24] Kvco_xs[0] (reset value 1); [25] 1802 Kvco_xs[1] (reset value 1); [26] Kvco_xs[2] (reset value 1); [27] 1803 testd_en (reset value 0); [28] testd_sel[0] (reset value 0); [29] 1804 testd_sel[1] (reset value 0); [30] testd_sel[2] (reset value 0); [31] 1805 testa_en (reset value 0); */ 1806 #define MISC_REG_PLL_STORM_CTRL_1 0xa294 1807 #define MISC_REG_PLL_STORM_CTRL_2 0xa298 1808 #define MISC_REG_PLL_STORM_CTRL_3 0xa29c 1809 #define MISC_REG_PLL_STORM_CTRL_4 0xa2a0 1810 /* [R 1] Status of 4 port mode enable input pin. */ 1811 #define MISC_REG_PORT4MODE_EN 0xa750 1812 /* [RW 2] 4 port mode enable overwrite.[0] - Overwrite control; if it is 0 - 1813 * the port4mode_en output is equal to 4 port mode input pin; if it is 1 - 1814 * the port4mode_en output is equal to bit[1] of this register; [1] - 1815 * Overwrite value. If bit[0] of this register is 1 this is the value that 1816 * receives the port4mode_en output . */ 1817 #define MISC_REG_PORT4MODE_EN_OVWR 0xa720 1818 /* [RW 32] reset reg#2; rite/read one = the specific block is out of reset; 1819 write/read zero = the specific block is in reset; addr 0-wr- the write 1820 value will be written to the register; addr 1-set - one will be written 1821 to all the bits that have the value of one in the data written (bits that 1822 have the value of zero will not be change) ; addr 2-clear - zero will be 1823 written to all the bits that have the value of one in the data written 1824 (bits that have the value of zero will not be change); addr 3-ignore; 1825 read ignore from all addr except addr 00; inside order of the bits is: 1826 [0] rst_bmac0; [1] rst_bmac1; [2] rst_emac0; [3] rst_emac1; [4] rst_grc; 1827 [5] rst_mcp_n_reset_reg_hard_core; [6] rst_ mcp_n_hard_core_rst_b; [7] 1828 rst_ mcp_n_reset_cmn_cpu; [8] rst_ mcp_n_reset_cmn_core; [9] rst_rbcn; 1829 [10] rst_dbg; [11] rst_misc_core; [12] rst_dbue (UART); [13] 1830 Pci_resetmdio_n; [14] rst_emac0_hard_core; [15] rst_emac1_hard_core; 16] 1831 rst_pxp_rq_rd_wr; 31:17] reserved */ 1832 #define MISC_REG_RESET_REG_1 0xa580 1833 #define MISC_REG_RESET_REG_2 0xa590 1834 /* [RW 20] 20 bit GRC address where the scratch-pad of the MCP that is 1835 shared with the driver resides */ 1836 #define MISC_REG_SHARED_MEM_ADDR 0xa2b4 1837 /* [RW 32] SPIO. [31-24] FLOAT When any of these bits is written as a '1'; 1838 the corresponding SPIO bit will turn off it's drivers and become an 1839 input. This is the reset state of all SPIO pins. The read value of these 1840 bits will be a '1' if that last command (#SET; #CL; or #FLOAT) for this 1841 bit was a #FLOAT. (reset value 0xff). [23-16] CLR When any of these bits 1842 is written as a '1'; the corresponding SPIO bit will drive low. The read 1843 value of these bits will be a '1' if that last command (#SET; #CLR; or 1844 #FLOAT) for this bit was a #CLR. (reset value 0). [15-8] SET When any of 1845 these bits is written as a '1'; the corresponding SPIO bit will drive 1846 high (if it has that capability). The read value of these bits will be a 1847 '1' if that last command (#SET; #CLR; or #FLOAT) for this bit was a #SET. 1848 (reset value 0). [7-0] VALUE RO; These bits indicate the read value of 1849 each of the eight SPIO pins. This is the result value of the pin; not the 1850 drive value. Writing these bits will have not effect. Each 8 bits field 1851 is divided as follows: [0] VAUX Enable; when pulsed low; enables supply 1852 from VAUX. (This is an output pin only; the FLOAT field is not applicable 1853 for this pin); [1] VAUX Disable; when pulsed low; disables supply form 1854 VAUX. (This is an output pin only; FLOAT field is not applicable for this 1855 pin); [2] SEL_VAUX_B - Control to power switching logic. Drive low to 1856 select VAUX supply. (This is an output pin only; it is not controlled by 1857 the SET and CLR fields; it is controlled by the Main Power SM; the FLOAT 1858 field is not applicable for this pin; only the VALUE fields is relevant - 1859 it reflects the output value); [3] port swap [4] spio_4; [5] spio_5; [6] 1860 Bit 0 of UMP device ID select; read by UMP firmware; [7] Bit 1 of UMP 1861 device ID select; read by UMP firmware. */ 1862 #define MISC_REG_SPIO 0xa4fc 1863 /* [RW 8] These bits enable the SPIO_INTs to signals event to the IGU/MC. 1864 according to the following map: [3:0] reserved; [4] spio_4 [5] spio_5; 1865 [7:0] reserved */ 1866 #define MISC_REG_SPIO_EVENT_EN 0xa2b8 1867 /* [RW 32] SPIO INT. [31-24] OLD_CLR Writing a '1' to these bit clears the 1868 corresponding bit in the #OLD_VALUE register. This will acknowledge an 1869 interrupt on the falling edge of corresponding SPIO input (reset value 1870 0). [23-16] OLD_SET Writing a '1' to these bit sets the corresponding bit 1871 in the #OLD_VALUE register. This will acknowledge an interrupt on the 1872 rising edge of corresponding SPIO input (reset value 0). [15-8] OLD_VALUE 1873 RO; These bits indicate the old value of the SPIO input value. When the 1874 ~INT_STATE bit is set; this bit indicates the OLD value of the pin such 1875 that if ~INT_STATE is set and this bit is '0'; then the interrupt is due 1876 to a low to high edge. If ~INT_STATE is set and this bit is '1'; then the 1877 interrupt is due to a high to low edge (reset value 0). [7-0] INT_STATE 1878 RO; These bits indicate the current SPIO interrupt state for each SPIO 1879 pin. This bit is cleared when the appropriate #OLD_SET or #OLD_CLR 1880 command bit is written. This bit is set when the SPIO input does not 1881 match the current value in #OLD_VALUE (reset value 0). */ 1882 #define MISC_REG_SPIO_INT 0xa500 1883 /* [RW 32] reload value for counter 4 if reload; the value will be reload if 1884 the counter reached zero and the reload bit 1885 (~misc_registers_sw_timer_cfg_4.sw_timer_cfg_4[1] ) is set */ 1886 #define MISC_REG_SW_TIMER_RELOAD_VAL_4 0xa2fc 1887 /* [RW 32] the value of the counter for sw timers1-8. there are 8 addresses 1888 in this register. address 0 - timer 1; address 1 - timer 2, ... address 7 - 1889 timer 8 */ 1890 #define MISC_REG_SW_TIMER_VAL 0xa5c0 1891 /* [R 1] Status of two port mode path swap input pin. */ 1892 #define MISC_REG_TWO_PORT_PATH_SWAP 0xa758 1893 /* [RW 2] 2 port swap overwrite.[0] - Overwrite control; if it is 0 - the 1894 path_swap output is equal to 2 port mode path swap input pin; if it is 1 1895 - the path_swap output is equal to bit[1] of this register; [1] - 1896 Overwrite value. If bit[0] of this register is 1 this is the value that 1897 receives the path_swap output. Reset on Hard reset. */ 1898 #define MISC_REG_TWO_PORT_PATH_SWAP_OVWR 0xa72c 1899 /* [RW 1] Set by the MCP to remember if one or more of the drivers is/are 1900 loaded; 0-prepare; -unprepare */ 1901 #define MISC_REG_UNPREPARED 0xa424 1902 #define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_BRCST (0x1<<0) 1903 #define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_MLCST (0x1<<1) 1904 #define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_NO_VLAN (0x1<<4) 1905 #define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_UNCST (0x1<<2) 1906 #define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_VLAN (0x1<<3) 1907 /* [RW 5] MDIO PHY Address. The WC uses this address to determine whether or 1908 * not it is the recipient of the message on the MDIO interface. The value 1909 * is compared to the value on ctrl_md_devad. Drives output 1910 * misc_xgxs0_phy_addr. Global register. */ 1911 #define MISC_REG_WC0_CTRL_PHY_ADDR 0xa9cc 1912 #define MISC_REG_WC0_RESET 0xac30 1913 /* [RW 2] XMAC Core port mode. Indicates the number of ports on the system 1914 side. This should be less than or equal to phy_port_mode; if some of the 1915 ports are not used. This enables reduction of frequency on the core side. 1916 This is a strap input for the XMAC_MP core. 00 - Single Port Mode; 01 - 1917 Dual Port Mode; 10 - Tri Port Mode; 11 - Quad Port Mode. This is a strap 1918 input for the XMAC_MP core; and should be changed only while reset is 1919 held low. Reset on Hard reset. */ 1920 #define MISC_REG_XMAC_CORE_PORT_MODE 0xa964 1921 /* [RW 2] XMAC PHY port mode. Indicates the number of ports on the Warp 1922 Core. This is a strap input for the XMAC_MP core. 00 - Single Port Mode; 1923 01 - Dual Port Mode; 1x - Quad Port Mode; This is a strap input for the 1924 XMAC_MP core; and should be changed only while reset is held low. Reset 1925 on Hard reset. */ 1926 #define MISC_REG_XMAC_PHY_PORT_MODE 0xa960 1927 /* [RW 32] 1 [47] Packet Size = 64 Write to this register write bits 31:0. 1928 * Reads from this register will clear bits 31:0. */ 1929 #define MSTAT_REG_RX_STAT_GR64_LO 0x200 1930 /* [RW 32] 1 [00] Tx Good Packet Count Write to this register write bits 1931 * 31:0. Reads from this register will clear bits 31:0. */ 1932 #define MSTAT_REG_TX_STAT_GTXPOK_LO 0 1933 #define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_BRCST (0x1<<0) 1934 #define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_MLCST (0x1<<1) 1935 #define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_NO_VLAN (0x1<<4) 1936 #define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_UNCST (0x1<<2) 1937 #define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_VLAN (0x1<<3) 1938 #define NIG_LLH0_XCM_MASK_REG_LLH0_XCM_MASK_BCN (0x1<<0) 1939 #define NIG_LLH1_XCM_MASK_REG_LLH1_XCM_MASK_BCN (0x1<<0) 1940 #define NIG_MASK_INTERRUPT_PORT0_REG_MASK_EMAC0_MISC_MI_INT (0x1<<0) 1941 #define NIG_MASK_INTERRUPT_PORT0_REG_MASK_SERDES0_LINK_STATUS (0x1<<9) 1942 #define NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK10G (0x1<<15) 1943 #define NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK_STATUS (0xf<<18) 1944 /* [RW 1] Input enable for RX_BMAC0 IF */ 1945 #define NIG_REG_BMAC0_IN_EN 0x100ac 1946 /* [RW 1] output enable for TX_BMAC0 IF */ 1947 #define NIG_REG_BMAC0_OUT_EN 0x100e0 1948 /* [RW 1] output enable for TX BMAC pause port 0 IF */ 1949 #define NIG_REG_BMAC0_PAUSE_OUT_EN 0x10110 1950 /* [RW 1] output enable for RX_BMAC0_REGS IF */ 1951 #define NIG_REG_BMAC0_REGS_OUT_EN 0x100e8 1952 /* [RW 1] output enable for RX BRB1 port0 IF */ 1953 #define NIG_REG_BRB0_OUT_EN 0x100f8 1954 /* [RW 1] Input enable for TX BRB1 pause port 0 IF */ 1955 #define NIG_REG_BRB0_PAUSE_IN_EN 0x100c4 1956 /* [RW 1] output enable for RX BRB1 port1 IF */ 1957 #define NIG_REG_BRB1_OUT_EN 0x100fc 1958 /* [RW 1] Input enable for TX BRB1 pause port 1 IF */ 1959 #define NIG_REG_BRB1_PAUSE_IN_EN 0x100c8 1960 /* [RW 1] output enable for RX BRB1 LP IF */ 1961 #define NIG_REG_BRB_LB_OUT_EN 0x10100 1962 /* [WB_W 82] Debug packet to LP from RBC; Data spelling:[63:0] data; 64] 1963 error; [67:65]eop_bvalid; [68]eop; [69]sop; [70]port_id; 71]flush; 1964 72:73]-vnic_num; 81:74]-sideband_info */ 1965 #define NIG_REG_DEBUG_PACKET_LB 0x10800 1966 /* [RW 1] Input enable for TX Debug packet */ 1967 #define NIG_REG_EGRESS_DEBUG_IN_EN 0x100dc 1968 /* [RW 1] If 1 - egress drain mode for port0 is active. In this mode all 1969 packets from PBFare not forwarded to the MAC and just deleted from FIFO. 1970 First packet may be deleted from the middle. And last packet will be 1971 always deleted till the end. */ 1972 #define NIG_REG_EGRESS_DRAIN0_MODE 0x10060 1973 /* [RW 1] Output enable to EMAC0 */ 1974 #define NIG_REG_EGRESS_EMAC0_OUT_EN 0x10120 1975 /* [RW 1] MAC configuration for packets of port0. If 1 - all packet outputs 1976 to emac for port0; other way to bmac for port0 */ 1977 #define NIG_REG_EGRESS_EMAC0_PORT 0x10058 1978 /* [RW 1] Input enable for TX PBF user packet port0 IF */ 1979 #define NIG_REG_EGRESS_PBF0_IN_EN 0x100cc 1980 /* [RW 1] Input enable for TX PBF user packet port1 IF */ 1981 #define NIG_REG_EGRESS_PBF1_IN_EN 0x100d0 1982 /* [RW 1] Input enable for TX UMP management packet port0 IF */ 1983 #define NIG_REG_EGRESS_UMP0_IN_EN 0x100d4 1984 /* [RW 1] Input enable for RX_EMAC0 IF */ 1985 #define NIG_REG_EMAC0_IN_EN 0x100a4 1986 /* [RW 1] output enable for TX EMAC pause port 0 IF */ 1987 #define NIG_REG_EMAC0_PAUSE_OUT_EN 0x10118 1988 /* [R 1] status from emac0. This bit is set when MDINT from either the 1989 EXT_MDINT pin or from the Copper PHY is driven low. This condition must 1990 be cleared in the attached PHY device that is driving the MINT pin. */ 1991 #define NIG_REG_EMAC0_STATUS_MISC_MI_INT 0x10494 1992 /* [WB 48] This address space contains BMAC0 registers. The BMAC registers 1993 are described in appendix A. In order to access the BMAC0 registers; the 1994 base address; NIG_REGISTERS_INGRESS_BMAC0_MEM; Offset: 0x10c00; should be 1995 added to each BMAC register offset */ 1996 #define NIG_REG_INGRESS_BMAC0_MEM 0x10c00 1997 /* [WB 48] This address space contains BMAC1 registers. The BMAC registers 1998 are described in appendix A. In order to access the BMAC0 registers; the 1999 base address; NIG_REGISTERS_INGRESS_BMAC1_MEM; Offset: 0x11000; should be 2000 added to each BMAC register offset */ 2001 #define NIG_REG_INGRESS_BMAC1_MEM 0x11000 2002 /* [R 1] FIFO empty in EOP descriptor FIFO of LP in NIG_RX_EOP */ 2003 #define NIG_REG_INGRESS_EOP_LB_EMPTY 0x104e0 2004 /* [RW 17] Debug only. RX_EOP_DSCR_lb_FIFO in NIG_RX_EOP. Data 2005 packet_length[13:0]; mac_error[14]; trunc_error[15]; parity[16] */ 2006 #define NIG_REG_INGRESS_EOP_LB_FIFO 0x104e4 2007 /* [RW 27] 0 - must be active for Everest A0; 1- for Everest B0 when latch 2008 logic for interrupts must be used. Enable per bit of interrupt of 2009 ~latch_status.latch_status */ 2010 #define NIG_REG_LATCH_BC_0 0x16210 2011 /* [RW 27] Latch for each interrupt from Unicore.b[0] 2012 status_emac0_misc_mi_int; b[1] status_emac0_misc_mi_complete; 2013 b[2]status_emac0_misc_cfg_change; b[3]status_emac0_misc_link_status; 2014 b[4]status_emac0_misc_link_change; b[5]status_emac0_misc_attn; 2015 b[6]status_serdes0_mac_crs; b[7]status_serdes0_autoneg_complete; 2016 b[8]status_serdes0_fiber_rxact; b[9]status_serdes0_link_status; 2017 b[10]status_serdes0_mr_page_rx; b[11]status_serdes0_cl73_an_complete; 2018 b[12]status_serdes0_cl73_mr_page_rx; b[13]status_serdes0_rx_sigdet; 2019 b[14]status_xgxs0_remotemdioreq; b[15]status_xgxs0_link10g; 2020 b[16]status_xgxs0_autoneg_complete; b[17]status_xgxs0_fiber_rxact; 2021 b[21:18]status_xgxs0_link_status; b[22]status_xgxs0_mr_page_rx; 2022 b[23]status_xgxs0_cl73_an_complete; b[24]status_xgxs0_cl73_mr_page_rx; 2023 b[25]status_xgxs0_rx_sigdet; b[26]status_xgxs0_mac_crs */ 2024 #define NIG_REG_LATCH_STATUS_0 0x18000 2025 /* [RW 1] led 10g for port 0 */ 2026 #define NIG_REG_LED_10G_P0 0x10320 2027 /* [RW 1] led 10g for port 1 */ 2028 #define NIG_REG_LED_10G_P1 0x10324 2029 /* [RW 1] Port0: This bit is set to enable the use of the 2030 ~nig_registers_led_control_blink_rate_p0.led_control_blink_rate_p0 field 2031 defined below. If this bit is cleared; then the blink rate will be about 2032 8Hz. */ 2033 #define NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 0x10318 2034 /* [RW 12] Port0: Specifies the period of each blink cycle (on + off) for 2035 Traffic LED in milliseconds. Must be a non-zero value. This 12-bit field 2036 is reset to 0x080; giving a default blink period of approximately 8Hz. */ 2037 #define NIG_REG_LED_CONTROL_BLINK_RATE_P0 0x10310 2038 /* [RW 1] Port0: If set along with the 2039 ~nig_registers_led_control_override_traffic_p0.led_control_override_traffic_p0 2040 bit and ~nig_registers_led_control_traffic_p0.led_control_traffic_p0 LED 2041 bit; the Traffic LED will blink with the blink rate specified in 2042 ~nig_registers_led_control_blink_rate_p0.led_control_blink_rate_p0 and 2043 ~nig_registers_led_control_blink_rate_ena_p0.led_control_blink_rate_ena_p0 2044 fields. */ 2045 #define NIG_REG_LED_CONTROL_BLINK_TRAFFIC_P0 0x10308 2046 /* [RW 1] Port0: If set overrides hardware control of the Traffic LED. The 2047 Traffic LED will then be controlled via bit ~nig_registers_ 2048 led_control_traffic_p0.led_control_traffic_p0 and bit 2049 ~nig_registers_led_control_blink_traffic_p0.led_control_blink_traffic_p0 */ 2050 #define NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 0x102f8 2051 /* [RW 1] Port0: If set along with the led_control_override_trafic_p0 bit; 2052 turns on the Traffic LED. If the led_control_blink_traffic_p0 bit is also 2053 set; the LED will blink with blink rate specified in 2054 ~nig_registers_led_control_blink_rate_p0.led_control_blink_rate_p0 and 2055 ~nig_regsters_led_control_blink_rate_ena_p0.led_control_blink_rate_ena_p0 2056 fields. */ 2057 #define NIG_REG_LED_CONTROL_TRAFFIC_P0 0x10300 2058 /* [RW 4] led mode for port0: 0 MAC; 1-3 PHY1; 4 MAC2; 5-7 PHY4; 8-MAC3; 2059 9-11PHY7; 12 MAC4; 13-15 PHY10; */ 2060 #define NIG_REG_LED_MODE_P0 0x102f0 2061 /* [RW 3] for port0 enable for llfc ppp and pause. b0 - brb1 enable; b1- 2062 tsdm enable; b2- usdm enable */ 2063 #define NIG_REG_LLFC_EGRESS_SRC_ENABLE_0 0x16070 2064 #define NIG_REG_LLFC_EGRESS_SRC_ENABLE_1 0x16074 2065 /* [RW 1] SAFC enable for port0. This register may get 1 only when 2066 ~ppp_enable.ppp_enable = 0 and pause_enable.pause_enable =0 for the same 2067 port */ 2068 #define NIG_REG_LLFC_ENABLE_0 0x16208 2069 #define NIG_REG_LLFC_ENABLE_1 0x1620c 2070 /* [RW 16] classes are high-priority for port0 */ 2071 #define NIG_REG_LLFC_HIGH_PRIORITY_CLASSES_0 0x16058 2072 #define NIG_REG_LLFC_HIGH_PRIORITY_CLASSES_1 0x1605c 2073 /* [RW 16] classes are low-priority for port0 */ 2074 #define NIG_REG_LLFC_LOW_PRIORITY_CLASSES_0 0x16060 2075 #define NIG_REG_LLFC_LOW_PRIORITY_CLASSES_1 0x16064 2076 /* [RW 1] Output enable of message to LLFC BMAC IF for port0 */ 2077 #define NIG_REG_LLFC_OUT_EN_0 0x160c8 2078 #define NIG_REG_LLFC_OUT_EN_1 0x160cc 2079 #define NIG_REG_LLH0_ACPI_PAT_0_CRC 0x1015c 2080 #define NIG_REG_LLH0_ACPI_PAT_6_LEN 0x10154 2081 #define NIG_REG_LLH0_BRB1_DRV_MASK 0x10244 2082 #define NIG_REG_LLH0_BRB1_DRV_MASK_MF 0x16048 2083 /* [RW 1] send to BRB1 if no match on any of RMP rules. */ 2084 #define NIG_REG_LLH0_BRB1_NOT_MCP 0x1025c 2085 /* [RW 2] Determine the classification participants. 0: no classification.1: 2086 classification upon VLAN id. 2: classification upon MAC address. 3: 2087 classification upon both VLAN id & MAC addr. */ 2088 #define NIG_REG_LLH0_CLS_TYPE 0x16080 2089 /* [RW 32] cm header for llh0 */ 2090 #define NIG_REG_LLH0_CM_HEADER 0x1007c 2091 #define NIG_REG_LLH0_DEST_IP_0_1 0x101dc 2092 #define NIG_REG_LLH0_DEST_MAC_0_0 0x101c0 2093 /* [RW 16] destination TCP address 1. The LLH will look for this address in 2094 all incoming packets. */ 2095 #define NIG_REG_LLH0_DEST_TCP_0 0x10220 2096 /* [RW 16] destination UDP address 1 The LLH will look for this address in 2097 all incoming packets. */ 2098 #define NIG_REG_LLH0_DEST_UDP_0 0x10214 2099 #define NIG_REG_LLH0_ERROR_MASK 0x1008c 2100 /* [RW 8] event id for llh0 */ 2101 #define NIG_REG_LLH0_EVENT_ID 0x10084 2102 #define NIG_REG_LLH0_FUNC_EN 0x160fc 2103 #define NIG_REG_LLH0_FUNC_MEM 0x16180 2104 #define NIG_REG_LLH0_FUNC_MEM_ENABLE 0x16140 2105 #define NIG_REG_LLH0_FUNC_VLAN_ID 0x16100 2106 /* [RW 1] Determine the IP version to look for in 2107 ~nig_registers_llh0_dest_ip_0.llh0_dest_ip_0. 0 - IPv6; 1-IPv4 */ 2108 #define NIG_REG_LLH0_IPV4_IPV6_0 0x10208 2109 /* [RW 1] t bit for llh0 */ 2110 #define NIG_REG_LLH0_T_BIT 0x10074 2111 /* [RW 12] VLAN ID 1. In case of VLAN packet the LLH will look for this ID. */ 2112 #define NIG_REG_LLH0_VLAN_ID_0 0x1022c 2113 /* [RW 8] init credit counter for port0 in LLH */ 2114 #define NIG_REG_LLH0_XCM_INIT_CREDIT 0x10554 2115 #define NIG_REG_LLH0_XCM_MASK 0x10130 2116 #define NIG_REG_LLH1_BRB1_DRV_MASK 0x10248 2117 /* [RW 1] send to BRB1 if no match on any of RMP rules. */ 2118 #define NIG_REG_LLH1_BRB1_NOT_MCP 0x102dc 2119 /* [RW 2] Determine the classification participants. 0: no classification.1: 2120 classification upon VLAN id. 2: classification upon MAC address. 3: 2121 classification upon both VLAN id & MAC addr. */ 2122 #define NIG_REG_LLH1_CLS_TYPE 0x16084 2123 /* [RW 32] cm header for llh1 */ 2124 #define NIG_REG_LLH1_CM_HEADER 0x10080 2125 #define NIG_REG_LLH1_ERROR_MASK 0x10090 2126 /* [RW 8] event id for llh1 */ 2127 #define NIG_REG_LLH1_EVENT_ID 0x10088 2128 #define NIG_REG_LLH1_FUNC_EN 0x16104 2129 #define NIG_REG_LLH1_FUNC_MEM 0x161c0 2130 #define NIG_REG_LLH1_FUNC_MEM_ENABLE 0x16160 2131 #define NIG_REG_LLH1_FUNC_MEM_SIZE 16 2132 /* [RW 1] When this bit is set; the LLH will classify the packet before 2133 * sending it to the BRB or calculating WoL on it. This bit controls port 1 2134 * only. The legacy llh_multi_function_mode bit controls port 0. */ 2135 #define NIG_REG_LLH1_MF_MODE 0x18614 2136 /* [RW 8] init credit counter for port1 in LLH */ 2137 #define NIG_REG_LLH1_XCM_INIT_CREDIT 0x10564 2138 #define NIG_REG_LLH1_XCM_MASK 0x10134 2139 /* [RW 1] When this bit is set; the LLH will expect all packets to be with 2140 e1hov */ 2141 #define NIG_REG_LLH_E1HOV_MODE 0x160d8 2142 /* [RW 16] Outer VLAN type identifier for multi-function mode. In non 2143 * multi-function mode; it will hold the inner VLAN type. Typically 0x8100. 2144 */ 2145 #define NIG_REG_LLH_E1HOV_TYPE_1 0x16028 2146 /* [RW 1] When this bit is set; the LLH will classify the packet before 2147 sending it to the BRB or calculating WoL on it. */ 2148 #define NIG_REG_LLH_MF_MODE 0x16024 2149 #define NIG_REG_MASK_INTERRUPT_PORT0 0x10330 2150 #define NIG_REG_MASK_INTERRUPT_PORT1 0x10334 2151 /* [RW 1] Output signal from NIG to EMAC0. When set enables the EMAC0 block. */ 2152 #define NIG_REG_NIG_EMAC0_EN 0x1003c 2153 /* [RW 1] Output signal from NIG to EMAC1. When set enables the EMAC1 block. */ 2154 #define NIG_REG_NIG_EMAC1_EN 0x10040 2155 /* [RW 1] Output signal from NIG to TX_EMAC0. When set indicates to the 2156 EMAC0 to strip the CRC from the ingress packets. */ 2157 #define NIG_REG_NIG_INGRESS_EMAC0_NO_CRC 0x10044 2158 /* [R 32] Interrupt register #0 read */ 2159 #define NIG_REG_NIG_INT_STS_0 0x103b0 2160 #define NIG_REG_NIG_INT_STS_1 0x103c0 2161 /* [RC 32] Interrupt register #0 read clear */ 2162 #define NIG_REG_NIG_INT_STS_CLR_0 0x103b4 2163 /* [R 32] Legacy E1 and E1H location for parity error mask register. */ 2164 #define NIG_REG_NIG_PRTY_MASK 0x103dc 2165 /* [RW 32] Parity mask register #0 read/write */ 2166 #define NIG_REG_NIG_PRTY_MASK_0 0x183c8 2167 #define NIG_REG_NIG_PRTY_MASK_1 0x183d8 2168 /* [R 32] Legacy E1 and E1H location for parity error status register. */ 2169 #define NIG_REG_NIG_PRTY_STS 0x103d0 2170 /* [R 32] Parity register #0 read */ 2171 #define NIG_REG_NIG_PRTY_STS_0 0x183bc 2172 #define NIG_REG_NIG_PRTY_STS_1 0x183cc 2173 /* [R 32] Legacy E1 and E1H location for parity error status clear register. */ 2174 #define NIG_REG_NIG_PRTY_STS_CLR 0x103d4 2175 /* [RC 32] Parity register #0 read clear */ 2176 #define NIG_REG_NIG_PRTY_STS_CLR_0 0x183c0 2177 #define NIG_REG_NIG_PRTY_STS_CLR_1 0x183d0 2178 #define MCPR_IMC_COMMAND_ENABLE (1L<<31) 2179 #define MCPR_IMC_COMMAND_IMC_STATUS_BITSHIFT 16 2180 #define MCPR_IMC_COMMAND_OPERATION_BITSHIFT 28 2181 #define MCPR_IMC_COMMAND_TRANSFER_ADDRESS_BITSHIFT 8 2182 /* [RW 6] Bit-map indicating which L2 hdrs may appear after the basic 2183 * Ethernet header. */ 2184 #define NIG_REG_P0_HDRS_AFTER_BASIC 0x18038 2185 /* [RW 1] HW PFC enable bit. Set this bit to enable the PFC functionality in 2186 * the NIG. Other flow control modes such as PAUSE and SAFC/LLFC should be 2187 * disabled when this bit is set. */ 2188 #define NIG_REG_P0_HWPFC_ENABLE 0x18078 2189 #define NIG_REG_P0_LLH_FUNC_MEM2 0x18480 2190 #define NIG_REG_P0_LLH_FUNC_MEM2_ENABLE 0x18440 2191 /* [RW 17] Packet TimeSync information that is buffered in 1-deep FIFOs for 2192 * the host. Bits [15:0] return the sequence ID of the packet. Bit 16 2193 * indicates the validity of the data in the buffer. Writing a 1 to bit 16 2194 * will clear the buffer. 2195 */ 2196 #define NIG_REG_P0_LLH_PTP_HOST_BUF_SEQID 0x1875c 2197 /* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for 2198 * the host. This location returns the lower 32 bits of timestamp value. 2199 */ 2200 #define NIG_REG_P0_LLH_PTP_HOST_BUF_TS_LSB 0x18754 2201 /* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for 2202 * the host. This location returns the upper 32 bits of timestamp value. 2203 */ 2204 #define NIG_REG_P0_LLH_PTP_HOST_BUF_TS_MSB 0x18758 2205 /* [RW 11] Mask register for the various parameters used in determining PTP 2206 * packet presence. Set each bit to 1 to mask out the particular parameter. 2207 * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of 2208 * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP 2209 * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC 2210 * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of 2211 * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable 2212 * MAC DA 2. The reset default is set to mask out all parameters. 2213 */ 2214 #define NIG_REG_P0_LLH_PTP_PARAM_MASK 0x187a0 2215 /* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set 2216 * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} . 2217 * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP 2218 * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1; 2219 * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC 2220 * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype 2221 * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset 2222 * default is to mask out all of the rules. Note that rules 0-3 are for IPv4 2223 * packets only and require that the packet is IPv4 for the rules to match. 2224 * Note that rules 4-7 are for IPv6 packets only and require that the packet 2225 * is IPv6 for the rules to match. 2226 */ 2227 #define NIG_REG_P0_LLH_PTP_RULE_MASK 0x187a4 2228 /* [RW 1] Set to 1 to enable PTP packets to be forwarded to the host. */ 2229 #define NIG_REG_P0_LLH_PTP_TO_HOST 0x187ac 2230 /* [RW 1] Input enable for RX MAC interface. */ 2231 #define NIG_REG_P0_MAC_IN_EN 0x185ac 2232 /* [RW 1] Output enable for TX MAC interface */ 2233 #define NIG_REG_P0_MAC_OUT_EN 0x185b0 2234 /* [RW 1] Output enable for TX PAUSE signal to the MAC. */ 2235 #define NIG_REG_P0_MAC_PAUSE_OUT_EN 0x185b4 2236 /* [RW 32] Eight 4-bit configurations for specifying which COS (0-15 for 2237 * future expansion) each priorty is to be mapped to. Bits 3:0 specify the 2238 * COS for priority 0. Bits 31:28 specify the COS for priority 7. The 3-bit 2239 * priority field is extracted from the outer-most VLAN in receive packet. 2240 * Only COS 0 and COS 1 are supported in E2. */ 2241 #define NIG_REG_P0_PKT_PRIORITY_TO_COS 0x18054 2242 /* [RW 6] Enable for TimeSync feature. Bits [2:0] are for RX side. Bits 2243 * [5:3] are for TX side. Bit 0 enables TimeSync on RX side. Bit 1 enables 2244 * V1 frame format in timesync event detection on RX side. Bit 2 enables V2 2245 * frame format in timesync event detection on RX side. Bit 3 enables 2246 * TimeSync on TX side. Bit 4 enables V1 frame format in timesync event 2247 * detection on TX side. Bit 5 enables V2 frame format in timesync event 2248 * detection on TX side. Note that for HW to detect PTP packet and extract 2249 * data from the packet, at least one of the version bits of that traffic 2250 * direction has to be enabled. 2251 */ 2252 #define NIG_REG_P0_PTP_EN 0x18788 2253 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 0. A 2254 * priority is mapped to COS 0 when the corresponding mask bit is 1. More 2255 * than one bit may be set; allowing multiple priorities to be mapped to one 2256 * COS. */ 2257 #define NIG_REG_P0_RX_COS0_PRIORITY_MASK 0x18058 2258 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 1. A 2259 * priority is mapped to COS 1 when the corresponding mask bit is 1. More 2260 * than one bit may be set; allowing multiple priorities to be mapped to one 2261 * COS. */ 2262 #define NIG_REG_P0_RX_COS1_PRIORITY_MASK 0x1805c 2263 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 2. A 2264 * priority is mapped to COS 2 when the corresponding mask bit is 1. More 2265 * than one bit may be set; allowing multiple priorities to be mapped to one 2266 * COS. */ 2267 #define NIG_REG_P0_RX_COS2_PRIORITY_MASK 0x186b0 2268 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 3. A 2269 * priority is mapped to COS 3 when the corresponding mask bit is 1. More 2270 * than one bit may be set; allowing multiple priorities to be mapped to one 2271 * COS. */ 2272 #define NIG_REG_P0_RX_COS3_PRIORITY_MASK 0x186b4 2273 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 4. A 2274 * priority is mapped to COS 4 when the corresponding mask bit is 1. More 2275 * than one bit may be set; allowing multiple priorities to be mapped to one 2276 * COS. */ 2277 #define NIG_REG_P0_RX_COS4_PRIORITY_MASK 0x186b8 2278 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 5. A 2279 * priority is mapped to COS 5 when the corresponding mask bit is 1. More 2280 * than one bit may be set; allowing multiple priorities to be mapped to one 2281 * COS. */ 2282 #define NIG_REG_P0_RX_COS5_PRIORITY_MASK 0x186bc 2283 /* [R 1] RX FIFO for receiving data from MAC is empty. */ 2284 /* [RW 15] Specify which of the credit registers the client is to be mapped 2285 * to. Bits[2:0] are for client 0; bits [14:12] are for client 4. For 2286 * clients that are not subject to WFQ credit blocking - their 2287 * specifications here are not used. */ 2288 #define NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP 0x180f0 2289 /* [RW 32] Specify which of the credit registers the client is to be mapped 2290 * to. This register specifies bits 31:0 of the 36-bit value. Bits[3:0] are 2291 * for client 0; bits [35:32] are for client 8. For clients that are not 2292 * subject to WFQ credit blocking - their specifications here are not used. 2293 * This is a new register (with 2_) added in E3 B0 to accommodate the 9 2294 * input clients to ETS arbiter. The reset default is set for management and 2295 * debug to use credit registers 6, 7, and 8, respectively, and COSes 0-5 to 2296 * use credit registers 0-5 respectively (0x543210876). Note that credit 2297 * registers can not be shared between clients. */ 2298 #define NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP2_LSB 0x18688 2299 /* [RW 4] Specify which of the credit registers the client is to be mapped 2300 * to. This register specifies bits 35:32 of the 36-bit value. Bits[3:0] are 2301 * for client 0; bits [35:32] are for client 8. For clients that are not 2302 * subject to WFQ credit blocking - their specifications here are not used. 2303 * This is a new register (with 2_) added in E3 B0 to accommodate the 9 2304 * input clients to ETS arbiter. The reset default is set for management and 2305 * debug to use credit registers 6, 7, and 8, respectively, and COSes 0-5 to 2306 * use credit registers 0-5 respectively (0x543210876). Note that credit 2307 * registers can not be shared between clients. */ 2308 #define NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP2_MSB 0x1868c 2309 /* [RW 5] Specify whether the client competes directly in the strict 2310 * priority arbiter. The bits are mapped according to client ID (client IDs 2311 * are defined in tx_arb_priority_client). Default value is set to enable 2312 * strict priorities for clients 0-2 -- management and debug traffic. */ 2313 #define NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT 0x180e8 2314 /* [RW 5] Specify whether the client is subject to WFQ credit blocking. The 2315 * bits are mapped according to client ID (client IDs are defined in 2316 * tx_arb_priority_client). Default value is 0 for not using WFQ credit 2317 * blocking. */ 2318 #define NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ 0x180ec 2319 /* [RW 32] Specify the upper bound that credit register 0 is allowed to 2320 * reach. */ 2321 #define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_0 0x1810c 2322 #define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_1 0x18110 2323 #define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_2 0x18114 2324 #define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_3 0x18118 2325 #define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_4 0x1811c 2326 #define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_5 0x186a0 2327 #define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_6 0x186a4 2328 #define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_7 0x186a8 2329 #define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_8 0x186ac 2330 /* [RW 32] Specify the weight (in bytes) to be added to credit register 0 2331 * when it is time to increment. */ 2332 #define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_0 0x180f8 2333 #define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_1 0x180fc 2334 #define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_2 0x18100 2335 #define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_3 0x18104 2336 #define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_4 0x18108 2337 #define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_5 0x18690 2338 #define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_6 0x18694 2339 #define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_7 0x18698 2340 #define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_8 0x1869c 2341 /* [RW 12] Specify the number of strict priority arbitration slots between 2342 * two round-robin arbitration slots to avoid starvation. A value of 0 means 2343 * no strict priority cycles - the strict priority with anti-starvation 2344 * arbiter becomes a round-robin arbiter. */ 2345 #define NIG_REG_P0_TX_ARB_NUM_STRICT_ARB_SLOTS 0x180f4 2346 /* [RW 15] Specify the client number to be assigned to each priority of the 2347 * strict priority arbiter. Priority 0 is the highest priority. Bits [2:0] 2348 * are for priority 0 client; bits [14:12] are for priority 4 client. The 2349 * clients are assigned the following IDs: 0-management; 1-debug traffic 2350 * from this port; 2-debug traffic from other port; 3-COS0 traffic; 4-COS1 2351 * traffic. The reset value[14:0] is set to 0x4688 (15'b100_011_010_001_000) 2352 * for management at priority 0; debug traffic at priorities 1 and 2; COS0 2353 * traffic at priority 3; and COS1 traffic at priority 4. */ 2354 #define NIG_REG_P0_TX_ARB_PRIORITY_CLIENT 0x180e4 2355 /* [RW 6] Bit-map indicating which L2 hdrs may appear after the basic 2356 * Ethernet header. */ 2357 #define NIG_REG_P1_HDRS_AFTER_BASIC 0x1818c 2358 #define NIG_REG_P1_LLH_FUNC_MEM2 0x184c0 2359 #define NIG_REG_P1_LLH_FUNC_MEM2_ENABLE 0x18460a 2360 /* [RW 17] Packet TimeSync information that is buffered in 1-deep FIFOs for 2361 * the host. Bits [15:0] return the sequence ID of the packet. Bit 16 2362 * indicates the validity of the data in the buffer. Writing a 1 to bit 16 2363 * will clear the buffer. 2364 */ 2365 #define NIG_REG_P1_LLH_PTP_HOST_BUF_SEQID 0x18774 2366 /* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for 2367 * the host. This location returns the lower 32 bits of timestamp value. 2368 */ 2369 #define NIG_REG_P1_LLH_PTP_HOST_BUF_TS_LSB 0x1876c 2370 /* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for 2371 * the host. This location returns the upper 32 bits of timestamp value. 2372 */ 2373 #define NIG_REG_P1_LLH_PTP_HOST_BUF_TS_MSB 0x18770 2374 /* [RW 11] Mask register for the various parameters used in determining PTP 2375 * packet presence. Set each bit to 1 to mask out the particular parameter. 2376 * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of 2377 * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP 2378 * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC 2379 * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of 2380 * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable 2381 * MAC DA 2. The reset default is set to mask out all parameters. 2382 */ 2383 #define NIG_REG_P1_LLH_PTP_PARAM_MASK 0x187c8 2384 /* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set 2385 * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} . 2386 * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP 2387 * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1; 2388 * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC 2389 * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype 2390 * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset 2391 * default is to mask out all of the rules. Note that rules 0-3 are for IPv4 2392 * packets only and require that the packet is IPv4 for the rules to match. 2393 * Note that rules 4-7 are for IPv6 packets only and require that the packet 2394 * is IPv6 for the rules to match. 2395 */ 2396 #define NIG_REG_P1_LLH_PTP_RULE_MASK 0x187cc 2397 /* [RW 1] Set to 1 to enable PTP packets to be forwarded to the host. */ 2398 #define NIG_REG_P1_LLH_PTP_TO_HOST 0x187d4 2399 /* [RW 32] Specify the client number to be assigned to each priority of the 2400 * strict priority arbiter. This register specifies bits 31:0 of the 36-bit 2401 * value. Priority 0 is the highest priority. Bits [3:0] are for priority 0 2402 * client; bits [35-32] are for priority 8 client. The clients are assigned 2403 * the following IDs: 0-management; 1-debug traffic from this port; 2-debug 2404 * traffic from other port; 3-COS0 traffic; 4-COS1 traffic; 5-COS2 traffic; 2405 * 6-COS3 traffic; 7-COS4 traffic; 8-COS5 traffic. The reset value[35:0] is 2406 * set to 0x345678021. This is a new register (with 2_) added in E3 B0 to 2407 * accommodate the 9 input clients to ETS arbiter. */ 2408 #define NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_LSB 0x18680 2409 /* [RW 4] Specify the client number to be assigned to each priority of the 2410 * strict priority arbiter. This register specifies bits 35:32 of the 36-bit 2411 * value. Priority 0 is the highest priority. Bits [3:0] are for priority 0 2412 * client; bits [35-32] are for priority 8 client. The clients are assigned 2413 * the following IDs: 0-management; 1-debug traffic from this port; 2-debug 2414 * traffic from other port; 3-COS0 traffic; 4-COS1 traffic; 5-COS2 traffic; 2415 * 6-COS3 traffic; 7-COS4 traffic; 8-COS5 traffic. The reset value[35:0] is 2416 * set to 0x345678021. This is a new register (with 2_) added in E3 B0 to 2417 * accommodate the 9 input clients to ETS arbiter. */ 2418 #define NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_MSB 0x18684 2419 /* [RW 1] MCP-to-host path enable. Set this bit to enable the routing of MCP 2420 * packets to BRB LB interface to forward the packet to the host. All 2421 * packets from MCP are forwarded to the network when this bit is cleared - 2422 * regardless of the configured destination in tx_mng_destination register. 2423 * When MCP-to-host paths for both ports 0 and 1 are disabled - the arbiter 2424 * for BRB LB interface is bypassed and PBF LB traffic is always selected to 2425 * send to BRB LB. 2426 */ 2427 #define NIG_REG_P0_TX_MNG_HOST_ENABLE 0x182f4 2428 #define NIG_REG_P1_HWPFC_ENABLE 0x181d0 2429 #define NIG_REG_P1_MAC_IN_EN 0x185c0 2430 /* [RW 1] Output enable for TX MAC interface */ 2431 #define NIG_REG_P1_MAC_OUT_EN 0x185c4 2432 /* [RW 1] Output enable for TX PAUSE signal to the MAC. */ 2433 #define NIG_REG_P1_MAC_PAUSE_OUT_EN 0x185c8 2434 /* [RW 32] Eight 4-bit configurations for specifying which COS (0-15 for 2435 * future expansion) each priorty is to be mapped to. Bits 3:0 specify the 2436 * COS for priority 0. Bits 31:28 specify the COS for priority 7. The 3-bit 2437 * priority field is extracted from the outer-most VLAN in receive packet. 2438 * Only COS 0 and COS 1 are supported in E2. */ 2439 #define NIG_REG_P1_PKT_PRIORITY_TO_COS 0x181a8 2440 /* [RW 6] Enable for TimeSync feature. Bits [2:0] are for RX side. Bits 2441 * [5:3] are for TX side. Bit 0 enables TimeSync on RX side. Bit 1 enables 2442 * V1 frame format in timesync event detection on RX side. Bit 2 enables V2 2443 * frame format in timesync event detection on RX side. Bit 3 enables 2444 * TimeSync on TX side. Bit 4 enables V1 frame format in timesync event 2445 * detection on TX side. Bit 5 enables V2 frame format in timesync event 2446 * detection on TX side. Note that for HW to detect PTP packet and extract 2447 * data from the packet, at least one of the version bits of that traffic 2448 * direction has to be enabled. 2449 */ 2450 #define NIG_REG_P1_PTP_EN 0x187b0 2451 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 0. A 2452 * priority is mapped to COS 0 when the corresponding mask bit is 1. More 2453 * than one bit may be set; allowing multiple priorities to be mapped to one 2454 * COS. */ 2455 #define NIG_REG_P1_RX_COS0_PRIORITY_MASK 0x181ac 2456 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 1. A 2457 * priority is mapped to COS 1 when the corresponding mask bit is 1. More 2458 * than one bit may be set; allowing multiple priorities to be mapped to one 2459 * COS. */ 2460 #define NIG_REG_P1_RX_COS1_PRIORITY_MASK 0x181b0 2461 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 2. A 2462 * priority is mapped to COS 2 when the corresponding mask bit is 1. More 2463 * than one bit may be set; allowing multiple priorities to be mapped to one 2464 * COS. */ 2465 #define NIG_REG_P1_RX_COS2_PRIORITY_MASK 0x186f8 2466 /* [R 1] RX FIFO for receiving data from MAC is empty. */ 2467 #define NIG_REG_P1_RX_MACFIFO_EMPTY 0x1858c 2468 /* [R 1] TLLH FIFO is empty. */ 2469 #define NIG_REG_P1_TLLH_FIFO_EMPTY 0x18338 2470 /* [RW 19] Packet TimeSync information that is buffered in 1-deep FIFOs for 2471 * TX side. Bits [15:0] reflect the sequence ID of the packet. Bit 16 2472 * indicates the validity of the data in the buffer. Bit 17 indicates that 2473 * the sequence ID is valid and it is waiting for the TX timestamp value. 2474 * Bit 18 indicates whether the timestamp is from a SW request (value of 1) 2475 * or HW request (value of 0). Writing a 1 to bit 16 will clear the buffer. 2476 */ 2477 #define NIG_REG_P0_TLLH_PTP_BUF_SEQID 0x187e0 2478 /* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for 2479 * MCP. This location returns the lower 32 bits of timestamp value. 2480 */ 2481 #define NIG_REG_P0_TLLH_PTP_BUF_TS_LSB 0x187d8 2482 /* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for 2483 * MCP. This location returns the upper 32 bits of timestamp value. 2484 */ 2485 #define NIG_REG_P0_TLLH_PTP_BUF_TS_MSB 0x187dc 2486 /* [RW 11] Mask register for the various parameters used in determining PTP 2487 * packet presence. Set each bit to 1 to mask out the particular parameter. 2488 * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of 2489 * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP 2490 * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC 2491 * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of 2492 * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable 2493 * MAC DA 2. The reset default is set to mask out all parameters. 2494 */ 2495 #define NIG_REG_P0_TLLH_PTP_PARAM_MASK 0x187f0 2496 /* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set 2497 * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} . 2498 * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP 2499 * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1; 2500 * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC 2501 * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype 2502 * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset 2503 * default is to mask out all of the rules. 2504 */ 2505 #define NIG_REG_P0_TLLH_PTP_RULE_MASK 0x187f4 2506 /* [RW 19] Packet TimeSync information that is buffered in 1-deep FIFOs for 2507 * TX side. Bits [15:0] reflect the sequence ID of the packet. Bit 16 2508 * indicates the validity of the data in the buffer. Bit 17 indicates that 2509 * the sequence ID is valid and it is waiting for the TX timestamp value. 2510 * Bit 18 indicates whether the timestamp is from a SW request (value of 1) 2511 * or HW request (value of 0). Writing a 1 to bit 16 will clear the buffer. 2512 */ 2513 #define NIG_REG_P1_TLLH_PTP_BUF_SEQID 0x187ec 2514 /* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for 2515 * MCP. This location returns the lower 32 bits of timestamp value. 2516 */ 2517 #define NIG_REG_P1_TLLH_PTP_BUF_TS_LSB 0x187e4 2518 /* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for 2519 * MCP. This location returns the upper 32 bits of timestamp value. 2520 */ 2521 #define NIG_REG_P1_TLLH_PTP_BUF_TS_MSB 0x187e8 2522 /* [RW 11] Mask register for the various parameters used in determining PTP 2523 * packet presence. Set each bit to 1 to mask out the particular parameter. 2524 * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of 2525 * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP 2526 * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC 2527 * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of 2528 * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable 2529 * MAC DA 2. The reset default is set to mask out all parameters. 2530 */ 2531 #define NIG_REG_P1_TLLH_PTP_PARAM_MASK 0x187f8 2532 /* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set 2533 * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} . 2534 * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP 2535 * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1; 2536 * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC 2537 * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype 2538 * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset 2539 * default is to mask out all of the rules. 2540 */ 2541 #define NIG_REG_P1_TLLH_PTP_RULE_MASK 0x187fc 2542 /* [RW 32] Specify which of the credit registers the client is to be mapped 2543 * to. This register specifies bits 31:0 of the 36-bit value. Bits[3:0] are 2544 * for client 0; bits [35:32] are for client 8. For clients that are not 2545 * subject to WFQ credit blocking - their specifications here are not used. 2546 * This is a new register (with 2_) added in E3 B0 to accommodate the 9 2547 * input clients to ETS arbiter. The reset default is set for management and 2548 * debug to use credit registers 6, 7, and 8, respectively, and COSes 0-5 to 2549 * use credit registers 0-5 respectively (0x543210876). Note that credit 2550 * registers can not be shared between clients. Note also that there are 2551 * only COS0-2 in port 1- there is a total of 6 clients in port 1. Only 2552 * credit registers 0-5 are valid. This register should be configured 2553 * appropriately before enabling WFQ. */ 2554 #define NIG_REG_P1_TX_ARB_CLIENT_CREDIT_MAP2_LSB 0x186e8 2555 /* [RW 4] Specify which of the credit registers the client is to be mapped 2556 * to. This register specifies bits 35:32 of the 36-bit value. Bits[3:0] are 2557 * for client 0; bits [35:32] are for client 8. For clients that are not 2558 * subject to WFQ credit blocking - their specifications here are not used. 2559 * This is a new register (with 2_) added in E3 B0 to accommodate the 9 2560 * input clients to ETS arbiter. The reset default is set for management and 2561 * debug to use credit registers 6, 7, and 8, respectively, and COSes 0-5 to 2562 * use credit registers 0-5 respectively (0x543210876). Note that credit 2563 * registers can not be shared between clients. Note also that there are 2564 * only COS0-2 in port 1- there is a total of 6 clients in port 1. Only 2565 * credit registers 0-5 are valid. This register should be configured 2566 * appropriately before enabling WFQ. */ 2567 #define NIG_REG_P1_TX_ARB_CLIENT_CREDIT_MAP2_MSB 0x186ec 2568 /* [RW 9] Specify whether the client competes directly in the strict 2569 * priority arbiter. The bits are mapped according to client ID (client IDs 2570 * are defined in tx_arb_priority_client2): 0-management; 1-debug traffic 2571 * from this port; 2-debug traffic from other port; 3-COS0 traffic; 4-COS1 2572 * traffic; 5-COS2 traffic; 6-COS3 traffic; 7-COS4 traffic; 8-COS5 traffic. 2573 * Default value is set to enable strict priorities for all clients. */ 2574 #define NIG_REG_P1_TX_ARB_CLIENT_IS_STRICT 0x18234 2575 /* [RW 9] Specify whether the client is subject to WFQ credit blocking. The 2576 * bits are mapped according to client ID (client IDs are defined in 2577 * tx_arb_priority_client2): 0-management; 1-debug traffic from this port; 2578 * 2-debug traffic from other port; 3-COS0 traffic; 4-COS1 traffic; 5-COS2 2579 * traffic; 6-COS3 traffic; 7-COS4 traffic; 8-COS5 traffic. Default value is 2580 * 0 for not using WFQ credit blocking. */ 2581 #define NIG_REG_P1_TX_ARB_CLIENT_IS_SUBJECT2WFQ 0x18238 2582 #define NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_0 0x18258 2583 #define NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_1 0x1825c 2584 #define NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_2 0x18260 2585 #define NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_3 0x18264 2586 #define NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_4 0x18268 2587 #define NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_5 0x186f4 2588 /* [RW 32] Specify the weight (in bytes) to be added to credit register 0 2589 * when it is time to increment. */ 2590 #define NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_0 0x18244 2591 #define NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_1 0x18248 2592 #define NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_2 0x1824c 2593 #define NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_3 0x18250 2594 #define NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_4 0x18254 2595 #define NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_5 0x186f0 2596 /* [RW 12] Specify the number of strict priority arbitration slots between 2597 two round-robin arbitration slots to avoid starvation. A value of 0 means 2598 no strict priority cycles - the strict priority with anti-starvation 2599 arbiter becomes a round-robin arbiter. */ 2600 #define NIG_REG_P1_TX_ARB_NUM_STRICT_ARB_SLOTS 0x18240 2601 /* [RW 32] Specify the client number to be assigned to each priority of the 2602 strict priority arbiter. This register specifies bits 31:0 of the 36-bit 2603 value. Priority 0 is the highest priority. Bits [3:0] are for priority 0 2604 client; bits [35-32] are for priority 8 client. The clients are assigned 2605 the following IDs: 0-management; 1-debug traffic from this port; 2-debug 2606 traffic from other port; 3-COS0 traffic; 4-COS1 traffic; 5-COS2 traffic; 2607 6-COS3 traffic; 7-COS4 traffic; 8-COS5 traffic. The reset value[35:0] is 2608 set to 0x345678021. This is a new register (with 2_) added in E3 B0 to 2609 accommodate the 9 input clients to ETS arbiter. Note that this register 2610 is the same as the one for port 0, except that port 1 only has COS 0-2 2611 traffic. There is no traffic for COS 3-5 of port 1. */ 2612 #define NIG_REG_P1_TX_ARB_PRIORITY_CLIENT2_LSB 0x186e0 2613 /* [RW 4] Specify the client number to be assigned to each priority of the 2614 strict priority arbiter. This register specifies bits 35:32 of the 36-bit 2615 value. Priority 0 is the highest priority. Bits [3:0] are for priority 0 2616 client; bits [35-32] are for priority 8 client. The clients are assigned 2617 the following IDs: 0-management; 1-debug traffic from this port; 2-debug 2618 traffic from other port; 3-COS0 traffic; 4-COS1 traffic; 5-COS2 traffic; 2619 6-COS3 traffic; 7-COS4 traffic; 8-COS5 traffic. The reset value[35:0] is 2620 set to 0x345678021. This is a new register (with 2_) added in E3 B0 to 2621 accommodate the 9 input clients to ETS arbiter. Note that this register 2622 is the same as the one for port 0, except that port 1 only has COS 0-2 2623 traffic. There is no traffic for COS 3-5 of port 1. */ 2624 #define NIG_REG_P1_TX_ARB_PRIORITY_CLIENT2_MSB 0x186e4 2625 /* [R 1] TX FIFO for transmitting data to MAC is empty. */ 2626 #define NIG_REG_P1_TX_MACFIFO_EMPTY 0x18594 2627 /* [RW 1] MCP-to-host path enable. Set this bit to enable the routing of MCP 2628 * packets to BRB LB interface to forward the packet to the host. All 2629 * packets from MCP are forwarded to the network when this bit is cleared - 2630 * regardless of the configured destination in tx_mng_destination register. 2631 */ 2632 #define NIG_REG_P1_TX_MNG_HOST_ENABLE 0x182f8 2633 /* [R 1] FIFO empty status of the MCP TX FIFO used for storing MCP packets 2634 forwarded to the host. */ 2635 #define NIG_REG_P1_TX_MNG_HOST_FIFO_EMPTY 0x182b8 2636 /* [RW 32] Specify the upper bound that credit register 0 is allowed to 2637 * reach. */ 2638 /* [RW 1] Pause enable for port0. This register may get 1 only when 2639 ~safc_enable.safc_enable = 0 and ppp_enable.ppp_enable =0 for the same 2640 port */ 2641 #define NIG_REG_PAUSE_ENABLE_0 0x160c0 2642 #define NIG_REG_PAUSE_ENABLE_1 0x160c4 2643 /* [RW 1] Input enable for RX PBF LP IF */ 2644 #define NIG_REG_PBF_LB_IN_EN 0x100b4 2645 /* [RW 1] Value of this register will be transmitted to port swap when 2646 ~nig_registers_strap_override.strap_override =1 */ 2647 #define NIG_REG_PORT_SWAP 0x10394 2648 /* [RW 1] PPP enable for port0. This register may get 1 only when 2649 * ~safc_enable.safc_enable = 0 and pause_enable.pause_enable =0 for the 2650 * same port */ 2651 #define NIG_REG_PPP_ENABLE_0 0x160b0 2652 #define NIG_REG_PPP_ENABLE_1 0x160b4 2653 /* [RW 1] output enable for RX parser descriptor IF */ 2654 #define NIG_REG_PRS_EOP_OUT_EN 0x10104 2655 /* [RW 1] Input enable for RX parser request IF */ 2656 #define NIG_REG_PRS_REQ_IN_EN 0x100b8 2657 /* [RW 5] control to serdes - CL45 DEVAD */ 2658 #define NIG_REG_SERDES0_CTRL_MD_DEVAD 0x10370 2659 /* [RW 1] control to serdes; 0 - clause 45; 1 - clause 22 */ 2660 #define NIG_REG_SERDES0_CTRL_MD_ST 0x1036c 2661 /* [RW 5] control to serdes - CL22 PHY_ADD and CL45 PRTAD */ 2662 #define NIG_REG_SERDES0_CTRL_PHY_ADDR 0x10374 2663 /* [R 1] status from serdes0 that inputs to interrupt logic of link status */ 2664 #define NIG_REG_SERDES0_STATUS_LINK_STATUS 0x10578 2665 /* [R 32] Rx statistics : In user packets discarded due to BRB backpressure 2666 for port0 */ 2667 #define NIG_REG_STAT0_BRB_DISCARD 0x105f0 2668 /* [R 32] Rx statistics : In user packets truncated due to BRB backpressure 2669 for port0 */ 2670 #define NIG_REG_STAT0_BRB_TRUNCATE 0x105f8 2671 /* [WB_R 36] Tx statistics : Number of packets from emac0 or bmac0 that 2672 between 1024 and 1522 bytes for port0 */ 2673 #define NIG_REG_STAT0_EGRESS_MAC_PKT0 0x10750 2674 /* [WB_R 36] Tx statistics : Number of packets from emac0 or bmac0 that 2675 between 1523 bytes and above for port0 */ 2676 #define NIG_REG_STAT0_EGRESS_MAC_PKT1 0x10760 2677 /* [R 32] Rx statistics : In user packets discarded due to BRB backpressure 2678 for port1 */ 2679 #define NIG_REG_STAT1_BRB_DISCARD 0x10628 2680 /* [WB_R 36] Tx statistics : Number of packets from emac1 or bmac1 that 2681 between 1024 and 1522 bytes for port1 */ 2682 #define NIG_REG_STAT1_EGRESS_MAC_PKT0 0x107a0 2683 /* [WB_R 36] Tx statistics : Number of packets from emac1 or bmac1 that 2684 between 1523 bytes and above for port1 */ 2685 #define NIG_REG_STAT1_EGRESS_MAC_PKT1 0x107b0 2686 /* [WB_R 64] Rx statistics : User octets received for LP */ 2687 #define NIG_REG_STAT2_BRB_OCTET 0x107e0 2688 #define NIG_REG_STATUS_INTERRUPT_PORT0 0x10328 2689 #define NIG_REG_STATUS_INTERRUPT_PORT1 0x1032c 2690 /* [RW 1] port swap mux selection. If this register equal to 0 then port 2691 swap is equal to SPIO pin that inputs from ifmux_serdes_swap. If 1 then 2692 ort swap is equal to ~nig_registers_port_swap.port_swap */ 2693 #define NIG_REG_STRAP_OVERRIDE 0x10398 2694 /* [WB 64] Addresses for TimeSync related registers in the timesync 2695 * generator sub-module. 2696 */ 2697 #define NIG_REG_TIMESYNC_GEN_REG 0x18800 2698 /* [RW 1] output enable for RX_XCM0 IF */ 2699 #define NIG_REG_XCM0_OUT_EN 0x100f0 2700 /* [RW 1] output enable for RX_XCM1 IF */ 2701 #define NIG_REG_XCM1_OUT_EN 0x100f4 2702 /* [RW 1] control to xgxs - remote PHY in-band MDIO */ 2703 #define NIG_REG_XGXS0_CTRL_EXTREMOTEMDIOST 0x10348 2704 /* [RW 5] control to xgxs - CL45 DEVAD */ 2705 #define NIG_REG_XGXS0_CTRL_MD_DEVAD 0x1033c 2706 /* [RW 1] control to xgxs; 0 - clause 45; 1 - clause 22 */ 2707 #define NIG_REG_XGXS0_CTRL_MD_ST 0x10338 2708 /* [RW 5] control to xgxs - CL22 PHY_ADD and CL45 PRTAD */ 2709 #define NIG_REG_XGXS0_CTRL_PHY_ADDR 0x10340 2710 /* [R 1] status from xgxs0 that inputs to interrupt logic of link10g. */ 2711 #define NIG_REG_XGXS0_STATUS_LINK10G 0x10680 2712 /* [R 4] status from xgxs0 that inputs to interrupt logic of link status */ 2713 #define NIG_REG_XGXS0_STATUS_LINK_STATUS 0x10684 2714 /* [RW 2] selection for XGXS lane of port 0 in NIG_MUX block */ 2715 #define NIG_REG_XGXS_LANE_SEL_P0 0x102e8 2716 /* [RW 1] selection for port0 for NIG_MUX block : 0 = SerDes; 1 = XGXS */ 2717 #define NIG_REG_XGXS_SERDES0_MODE_SEL 0x102e0 2718 #define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_EMAC0_MISC_MI_INT (0x1<<0) 2719 #define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_SERDES0_LINK_STATUS (0x1<<9) 2720 #define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK10G (0x1<<15) 2721 #define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS (0xf<<18) 2722 #define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS_SIZE 18 2723 /* [RW 31] The upper bound of the weight of COS0 in the ETS command arbiter. */ 2724 #define PBF_REG_COS0_UPPER_BOUND 0x15c05c 2725 /* [RW 31] The upper bound of the weight of COS0 in the ETS command arbiter 2726 * of port 0. */ 2727 #define PBF_REG_COS0_UPPER_BOUND_P0 0x15c2cc 2728 /* [RW 31] The upper bound of the weight of COS0 in the ETS command arbiter 2729 * of port 1. */ 2730 #define PBF_REG_COS0_UPPER_BOUND_P1 0x15c2e4 2731 /* [RW 31] The weight of COS0 in the ETS command arbiter. */ 2732 #define PBF_REG_COS0_WEIGHT 0x15c054 2733 /* [RW 31] The weight of COS0 in port 0 ETS command arbiter. */ 2734 #define PBF_REG_COS0_WEIGHT_P0 0x15c2a8 2735 /* [RW 31] The weight of COS0 in port 1 ETS command arbiter. */ 2736 #define PBF_REG_COS0_WEIGHT_P1 0x15c2c0 2737 /* [RW 31] The upper bound of the weight of COS1 in the ETS command arbiter. */ 2738 #define PBF_REG_COS1_UPPER_BOUND 0x15c060 2739 /* [RW 31] The weight of COS1 in the ETS command arbiter. */ 2740 #define PBF_REG_COS1_WEIGHT 0x15c058 2741 /* [RW 31] The weight of COS1 in port 0 ETS command arbiter. */ 2742 #define PBF_REG_COS1_WEIGHT_P0 0x15c2ac 2743 /* [RW 31] The weight of COS1 in port 1 ETS command arbiter. */ 2744 #define PBF_REG_COS1_WEIGHT_P1 0x15c2c4 2745 /* [RW 31] The weight of COS2 in port 0 ETS command arbiter. */ 2746 #define PBF_REG_COS2_WEIGHT_P0 0x15c2b0 2747 /* [RW 31] The weight of COS2 in port 1 ETS command arbiter. */ 2748 #define PBF_REG_COS2_WEIGHT_P1 0x15c2c8 2749 /* [RW 31] The weight of COS3 in port 0 ETS command arbiter. */ 2750 #define PBF_REG_COS3_WEIGHT_P0 0x15c2b4 2751 /* [RW 31] The weight of COS4 in port 0 ETS command arbiter. */ 2752 #define PBF_REG_COS4_WEIGHT_P0 0x15c2b8 2753 /* [RW 31] The weight of COS5 in port 0 ETS command arbiter. */ 2754 #define PBF_REG_COS5_WEIGHT_P0 0x15c2bc 2755 /* [R 11] Current credit for the LB queue in the tx port buffers in 16 byte 2756 * lines. */ 2757 #define PBF_REG_CREDIT_LB_Q 0x140338 2758 /* [R 11] Current credit for queue 0 in the tx port buffers in 16 byte 2759 * lines. */ 2760 #define PBF_REG_CREDIT_Q0 0x14033c 2761 /* [R 11] Current credit for queue 1 in the tx port buffers in 16 byte 2762 * lines. */ 2763 #define PBF_REG_CREDIT_Q1 0x140340 2764 /* [RW 1] Disable processing further tasks from port 0 (after ending the 2765 current task in process). */ 2766 #define PBF_REG_DISABLE_NEW_TASK_PROC_P0 0x14005c 2767 /* [RW 1] Disable processing further tasks from port 1 (after ending the 2768 current task in process). */ 2769 #define PBF_REG_DISABLE_NEW_TASK_PROC_P1 0x140060 2770 /* [RW 1] Disable processing further tasks from port 4 (after ending the 2771 current task in process). */ 2772 #define PBF_REG_DISABLE_NEW_TASK_PROC_P4 0x14006c 2773 #define PBF_REG_DISABLE_PF 0x1402e8 2774 #define PBF_REG_DISABLE_VF 0x1402ec 2775 /* [RW 18] For port 0: For each client that is subject to WFQ (the 2776 * corresponding bit is 1); indicates to which of the credit registers this 2777 * client is mapped. For clients which are not credit blocked; their mapping 2778 * is dont care. */ 2779 #define PBF_REG_ETS_ARB_CLIENT_CREDIT_MAP_P0 0x15c288 2780 /* [RW 9] For port 1: For each client that is subject to WFQ (the 2781 * corresponding bit is 1); indicates to which of the credit registers this 2782 * client is mapped. For clients which are not credit blocked; their mapping 2783 * is dont care. */ 2784 #define PBF_REG_ETS_ARB_CLIENT_CREDIT_MAP_P1 0x15c28c 2785 /* [RW 6] For port 0: Bit per client to indicate if the client competes in 2786 * the strict priority arbiter directly (corresponding bit = 1); or first 2787 * goes to the RR arbiter (corresponding bit = 0); and then competes in the 2788 * lowest priority in the strict-priority arbiter. */ 2789 #define PBF_REG_ETS_ARB_CLIENT_IS_STRICT_P0 0x15c278 2790 /* [RW 3] For port 1: Bit per client to indicate if the client competes in 2791 * the strict priority arbiter directly (corresponding bit = 1); or first 2792 * goes to the RR arbiter (corresponding bit = 0); and then competes in the 2793 * lowest priority in the strict-priority arbiter. */ 2794 #define PBF_REG_ETS_ARB_CLIENT_IS_STRICT_P1 0x15c27c 2795 /* [RW 6] For port 0: Bit per client to indicate if the client is subject to 2796 * WFQ credit blocking (corresponding bit = 1). */ 2797 #define PBF_REG_ETS_ARB_CLIENT_IS_SUBJECT2WFQ_P0 0x15c280 2798 /* [RW 3] For port 0: Bit per client to indicate if the client is subject to 2799 * WFQ credit blocking (corresponding bit = 1). */ 2800 #define PBF_REG_ETS_ARB_CLIENT_IS_SUBJECT2WFQ_P1 0x15c284 2801 /* [RW 16] For port 0: The number of strict priority arbitration slots 2802 * between 2 RR arbitration slots. A value of 0 means no strict priority 2803 * cycles; i.e. the strict-priority w/ anti-starvation arbiter is a RR 2804 * arbiter. */ 2805 #define PBF_REG_ETS_ARB_NUM_STRICT_ARB_SLOTS_P0 0x15c2a0 2806 /* [RW 16] For port 1: The number of strict priority arbitration slots 2807 * between 2 RR arbitration slots. A value of 0 means no strict priority 2808 * cycles; i.e. the strict-priority w/ anti-starvation arbiter is a RR 2809 * arbiter. */ 2810 #define PBF_REG_ETS_ARB_NUM_STRICT_ARB_SLOTS_P1 0x15c2a4 2811 /* [RW 18] For port 0: Indicates which client is connected to each priority 2812 * in the strict-priority arbiter. Priority 0 is the highest priority, and 2813 * priority 5 is the lowest; to which the RR output is connected to (this is 2814 * not configurable). */ 2815 #define PBF_REG_ETS_ARB_PRIORITY_CLIENT_P0 0x15c270 2816 /* [RW 9] For port 1: Indicates which client is connected to each priority 2817 * in the strict-priority arbiter. Priority 0 is the highest priority, and 2818 * priority 5 is the lowest; to which the RR output is connected to (this is 2819 * not configurable). */ 2820 #define PBF_REG_ETS_ARB_PRIORITY_CLIENT_P1 0x15c274 2821 /* [RW 1] Indicates that ETS is performed between the COSes in the command 2822 * arbiter. If reset strict priority w/ anti-starvation will be performed 2823 * w/o WFQ. */ 2824 #define PBF_REG_ETS_ENABLED 0x15c050 2825 /* [RW 6] Bit-map indicating which L2 hdrs may appear after the basic 2826 * Ethernet header. */ 2827 #define PBF_REG_HDRS_AFTER_BASIC 0x15c0a8 2828 /* [RW 6] Bit-map indicating which L2 hdrs may appear after L2 tag 0 */ 2829 #define PBF_REG_HDRS_AFTER_TAG_0 0x15c0b8 2830 /* [R 1] Removed for E3 B0 - Indicates which COS is conncted to the highest 2831 * priority in the command arbiter. */ 2832 #define PBF_REG_HIGH_PRIORITY_COS_NUM 0x15c04c 2833 #define PBF_REG_IF_ENABLE_REG 0x140044 2834 /* [RW 1] Init bit. When set the initial credits are copied to the credit 2835 registers (except the port credits). Should be set and then reset after 2836 the configuration of the block has ended. */ 2837 #define PBF_REG_INIT 0x140000 2838 /* [RW 11] Initial credit for the LB queue in the tx port buffers in 16 byte 2839 * lines. */ 2840 #define PBF_REG_INIT_CRD_LB_Q 0x15c248 2841 /* [RW 11] Initial credit for queue 0 in the tx port buffers in 16 byte 2842 * lines. */ 2843 #define PBF_REG_INIT_CRD_Q0 0x15c230 2844 /* [RW 11] Initial credit for queue 1 in the tx port buffers in 16 byte 2845 * lines. */ 2846 #define PBF_REG_INIT_CRD_Q1 0x15c234 2847 /* [RW 1] Init bit for port 0. When set the initial credit of port 0 is 2848 copied to the credit register. Should be set and then reset after the 2849 configuration of the port has ended. */ 2850 #define PBF_REG_INIT_P0 0x140004 2851 /* [RW 1] Init bit for port 1. When set the initial credit of port 1 is 2852 copied to the credit register. Should be set and then reset after the 2853 configuration of the port has ended. */ 2854 #define PBF_REG_INIT_P1 0x140008 2855 /* [RW 1] Init bit for port 4. When set the initial credit of port 4 is 2856 copied to the credit register. Should be set and then reset after the 2857 configuration of the port has ended. */ 2858 #define PBF_REG_INIT_P4 0x14000c 2859 /* [R 32] Cyclic counter for the amount credits in 16 bytes lines added for 2860 * the LB queue. Reset upon init. */ 2861 #define PBF_REG_INTERNAL_CRD_FREED_CNT_LB_Q 0x140354 2862 /* [R 32] Cyclic counter for the amount credits in 16 bytes lines added for 2863 * queue 0. Reset upon init. */ 2864 #define PBF_REG_INTERNAL_CRD_FREED_CNT_Q0 0x140358 2865 /* [R 32] Cyclic counter for the amount credits in 16 bytes lines added for 2866 * queue 1. Reset upon init. */ 2867 #define PBF_REG_INTERNAL_CRD_FREED_CNT_Q1 0x14035c 2868 /* [RW 1] Enable for mac interface 0. */ 2869 #define PBF_REG_MAC_IF0_ENABLE 0x140030 2870 /* [RW 1] Enable for mac interface 1. */ 2871 #define PBF_REG_MAC_IF1_ENABLE 0x140034 2872 /* [RW 1] Enable for the loopback interface. */ 2873 #define PBF_REG_MAC_LB_ENABLE 0x140040 2874 /* [RW 6] Bit-map indicating which headers must appear in the packet */ 2875 #define PBF_REG_MUST_HAVE_HDRS 0x15c0c4 2876 /* [RW 16] The number of strict priority arbitration slots between 2 RR 2877 * arbitration slots. A value of 0 means no strict priority cycles; i.e. the 2878 * strict-priority w/ anti-starvation arbiter is a RR arbiter. */ 2879 #define PBF_REG_NUM_STRICT_ARB_SLOTS 0x15c064 2880 /* [RW 10] Port 0 threshold used by arbiter in 16 byte lines used when pause 2881 not suppoterd. */ 2882 #define PBF_REG_P0_ARB_THRSH 0x1400e4 2883 /* [R 11] Current credit for port 0 in the tx port buffers in 16 byte lines. */ 2884 #define PBF_REG_P0_CREDIT 0x140200 2885 /* [RW 11] Initial credit for port 0 in the tx port buffers in 16 byte 2886 lines. */ 2887 #define PBF_REG_P0_INIT_CRD 0x1400d0 2888 /* [R 32] Cyclic counter for the amount credits in 16 bytes lines added for 2889 * port 0. Reset upon init. */ 2890 #define PBF_REG_P0_INTERNAL_CRD_FREED_CNT 0x140308 2891 /* [R 1] Removed for E3 B0 - Indication that pause is enabled for port 0. */ 2892 #define PBF_REG_P0_PAUSE_ENABLE 0x140014 2893 /* [R 8] Removed for E3 B0 - Number of tasks in port 0 task queue. */ 2894 #define PBF_REG_P0_TASK_CNT 0x140204 2895 /* [R 32] Removed for E3 B0 - Cyclic counter for number of 8 byte lines 2896 * freed from the task queue of port 0. Reset upon init. */ 2897 #define PBF_REG_P0_TQ_LINES_FREED_CNT 0x1402f0 2898 /* [R 12] Number of 8 bytes lines occupied in the task queue of port 0. */ 2899 #define PBF_REG_P0_TQ_OCCUPANCY 0x1402fc 2900 /* [R 11] Removed for E3 B0 - Current credit for port 1 in the tx port 2901 * buffers in 16 byte lines. */ 2902 #define PBF_REG_P1_CREDIT 0x140208 2903 /* [R 11] Removed for E3 B0 - Initial credit for port 0 in the tx port 2904 * buffers in 16 byte lines. */ 2905 #define PBF_REG_P1_INIT_CRD 0x1400d4 2906 /* [R 32] Cyclic counter for the amount credits in 16 bytes lines added for 2907 * port 1. Reset upon init. */ 2908 #define PBF_REG_P1_INTERNAL_CRD_FREED_CNT 0x14030c 2909 /* [R 8] Removed for E3 B0 - Number of tasks in port 1 task queue. */ 2910 #define PBF_REG_P1_TASK_CNT 0x14020c 2911 /* [R 32] Removed for E3 B0 - Cyclic counter for number of 8 byte lines 2912 * freed from the task queue of port 1. Reset upon init. */ 2913 #define PBF_REG_P1_TQ_LINES_FREED_CNT 0x1402f4 2914 /* [R 12] Number of 8 bytes lines occupied in the task queue of port 1. */ 2915 #define PBF_REG_P1_TQ_OCCUPANCY 0x140300 2916 /* [R 11] Current credit for port 4 in the tx port buffers in 16 byte lines. */ 2917 #define PBF_REG_P4_CREDIT 0x140210 2918 /* [RW 11] Initial credit for port 4 in the tx port buffers in 16 byte 2919 lines. */ 2920 #define PBF_REG_P4_INIT_CRD 0x1400e0 2921 /* [R 32] Cyclic counter for the amount credits in 16 bytes lines added for 2922 * port 4. Reset upon init. */ 2923 #define PBF_REG_P4_INTERNAL_CRD_FREED_CNT 0x140310 2924 /* [R 8] Removed for E3 B0 - Number of tasks in port 4 task queue. */ 2925 #define PBF_REG_P4_TASK_CNT 0x140214 2926 /* [R 32] Removed for E3 B0 - Cyclic counter for number of 8 byte lines 2927 * freed from the task queue of port 4. Reset upon init. */ 2928 #define PBF_REG_P4_TQ_LINES_FREED_CNT 0x1402f8 2929 /* [R 12] Number of 8 bytes lines occupied in the task queue of port 4. */ 2930 #define PBF_REG_P4_TQ_OCCUPANCY 0x140304 2931 /* [RW 5] Interrupt mask register #0 read/write */ 2932 #define PBF_REG_PBF_INT_MASK 0x1401d4 2933 /* [R 5] Interrupt register #0 read */ 2934 #define PBF_REG_PBF_INT_STS 0x1401c8 2935 /* [RW 20] Parity mask register #0 read/write */ 2936 #define PBF_REG_PBF_PRTY_MASK 0x1401e4 2937 /* [R 28] Parity register #0 read */ 2938 #define PBF_REG_PBF_PRTY_STS 0x1401d8 2939 /* [RC 20] Parity register #0 read clear */ 2940 #define PBF_REG_PBF_PRTY_STS_CLR 0x1401dc 2941 /* [RW 16] The Ethernet type value for L2 tag 0 */ 2942 #define PBF_REG_TAG_ETHERTYPE_0 0x15c090 2943 /* [RW 4] The length of the info field for L2 tag 0. The length is between 2944 * 2B and 14B; in 2B granularity */ 2945 #define PBF_REG_TAG_LEN_0 0x15c09c 2946 /* [R 32] Cyclic counter for number of 8 byte lines freed from the LB task 2947 * queue. Reset upon init. */ 2948 #define PBF_REG_TQ_LINES_FREED_CNT_LB_Q 0x14038c 2949 /* [R 32] Cyclic counter for number of 8 byte lines freed from the task 2950 * queue 0. Reset upon init. */ 2951 #define PBF_REG_TQ_LINES_FREED_CNT_Q0 0x140390 2952 /* [R 32] Cyclic counter for number of 8 byte lines freed from task queue 1. 2953 * Reset upon init. */ 2954 #define PBF_REG_TQ_LINES_FREED_CNT_Q1 0x140394 2955 /* [R 13] Number of 8 bytes lines occupied in the task queue of the LB 2956 * queue. */ 2957 #define PBF_REG_TQ_OCCUPANCY_LB_Q 0x1403a8 2958 /* [R 13] Number of 8 bytes lines occupied in the task queue of queue 0. */ 2959 #define PBF_REG_TQ_OCCUPANCY_Q0 0x1403ac 2960 /* [R 13] Number of 8 bytes lines occupied in the task queue of queue 1. */ 2961 #define PBF_REG_TQ_OCCUPANCY_Q1 0x1403b0 2962 /* [RW 16] One of 8 values that should be compared to type in Ethernet 2963 * parsing. If there is a match; the field after Ethernet is the first VLAN. 2964 * Reset value is 0x8100 which is the standard VLAN type. Note that when 2965 * checking second VLAN; type is compared only to 0x8100. 2966 */ 2967 #define PBF_REG_VLAN_TYPE_0 0x15c06c 2968 /* [RW 2] Interrupt mask register #0 read/write */ 2969 #define PB_REG_PB_INT_MASK 0x28 2970 /* [R 2] Interrupt register #0 read */ 2971 #define PB_REG_PB_INT_STS 0x1c 2972 /* [RW 4] Parity mask register #0 read/write */ 2973 #define PB_REG_PB_PRTY_MASK 0x38 2974 /* [R 4] Parity register #0 read */ 2975 #define PB_REG_PB_PRTY_STS 0x2c 2976 /* [RC 4] Parity register #0 read clear */ 2977 #define PB_REG_PB_PRTY_STS_CLR 0x30 2978 #define PGLUE_B_PGLUE_B_INT_STS_REG_ADDRESS_ERROR (0x1<<0) 2979 #define PGLUE_B_PGLUE_B_INT_STS_REG_CSSNOOP_FIFO_OVERFLOW (0x1<<8) 2980 #define PGLUE_B_PGLUE_B_INT_STS_REG_INCORRECT_RCV_BEHAVIOR (0x1<<1) 2981 #define PGLUE_B_PGLUE_B_INT_STS_REG_TCPL_ERROR_ATTN (0x1<<6) 2982 #define PGLUE_B_PGLUE_B_INT_STS_REG_TCPL_IN_TWO_RCBS_ATTN (0x1<<7) 2983 #define PGLUE_B_PGLUE_B_INT_STS_REG_VF_GRC_SPACE_VIOLATION_ATTN (0x1<<4) 2984 #define PGLUE_B_PGLUE_B_INT_STS_REG_VF_LENGTH_VIOLATION_ATTN (0x1<<3) 2985 #define PGLUE_B_PGLUE_B_INT_STS_REG_VF_MSIX_BAR_VIOLATION_ATTN (0x1<<5) 2986 #define PGLUE_B_PGLUE_B_INT_STS_REG_WAS_ERROR_ATTN (0x1<<2) 2987 /* [R 8] Config space A attention dirty bits. Each bit indicates that the 2988 * corresponding PF generates config space A attention. Set by PXP. Reset by 2989 * MCP writing 1 to icfg_space_a_request_clr. Note: register contains bits 2990 * from both paths. */ 2991 #define PGLUE_B_REG_CFG_SPACE_A_REQUEST 0x9010 2992 /* [R 8] Config space B attention dirty bits. Each bit indicates that the 2993 * corresponding PF generates config space B attention. Set by PXP. Reset by 2994 * MCP writing 1 to icfg_space_b_request_clr. Note: register contains bits 2995 * from both paths. */ 2996 #define PGLUE_B_REG_CFG_SPACE_B_REQUEST 0x9014 2997 /* [RW 1] Type A PF enable inbound interrupt table for CSDM. 0 - disable; 1 2998 * - enable. */ 2999 #define PGLUE_B_REG_CSDM_INB_INT_A_PF_ENABLE 0x9194 3000 /* [RW 18] Type B VF inbound interrupt table for CSDM: bits[17:9]-mask; 3001 * its[8:0]-address. Bits [1:0] must be zero (DW resolution address). */ 3002 #define PGLUE_B_REG_CSDM_INB_INT_B_VF 0x916c 3003 /* [RW 1] Type B VF enable inbound interrupt table for CSDM. 0 - disable; 1 3004 * - enable. */ 3005 #define PGLUE_B_REG_CSDM_INB_INT_B_VF_ENABLE 0x919c 3006 /* [RW 16] Start offset of CSDM zone A (queue zone) in the internal RAM */ 3007 #define PGLUE_B_REG_CSDM_START_OFFSET_A 0x9100 3008 /* [RW 16] Start offset of CSDM zone B (legacy zone) in the internal RAM */ 3009 #define PGLUE_B_REG_CSDM_START_OFFSET_B 0x9108 3010 /* [RW 5] VF Shift of CSDM zone B (legacy zone) in the internal RAM */ 3011 #define PGLUE_B_REG_CSDM_VF_SHIFT_B 0x9110 3012 /* [RW 1] 0 - Zone A size is 136x32B; 1 - Zone A size is 152x32B. */ 3013 #define PGLUE_B_REG_CSDM_ZONE_A_SIZE_PF 0x91ac 3014 /* [R 8] FLR request attention dirty bits for PFs 0 to 7. Each bit indicates 3015 * that the FLR register of the corresponding PF was set. Set by PXP. Reset 3016 * by MCP writing 1 to flr_request_pf_7_0_clr. Note: register contains bits 3017 * from both paths. */ 3018 #define PGLUE_B_REG_FLR_REQUEST_PF_7_0 0x9028 3019 /* [W 8] FLR request attention dirty bits clear for PFs 0 to 7. MCP writes 1 3020 * to a bit in this register in order to clear the corresponding bit in 3021 * flr_request_pf_7_0 register. Note: register contains bits from both 3022 * paths. */ 3023 #define PGLUE_B_REG_FLR_REQUEST_PF_7_0_CLR 0x9418 3024 /* [R 32] FLR request attention dirty bits for VFs 96 to 127. Each bit 3025 * indicates that the FLR register of the corresponding VF was set. Set by 3026 * PXP. Reset by MCP writing 1 to flr_request_vf_127_96_clr. */ 3027 #define PGLUE_B_REG_FLR_REQUEST_VF_127_96 0x9024 3028 /* [R 32] FLR request attention dirty bits for VFs 0 to 31. Each bit 3029 * indicates that the FLR register of the corresponding VF was set. Set by 3030 * PXP. Reset by MCP writing 1 to flr_request_vf_31_0_clr. */ 3031 #define PGLUE_B_REG_FLR_REQUEST_VF_31_0 0x9018 3032 /* [R 32] FLR request attention dirty bits for VFs 32 to 63. Each bit 3033 * indicates that the FLR register of the corresponding VF was set. Set by 3034 * PXP. Reset by MCP writing 1 to flr_request_vf_63_32_clr. */ 3035 #define PGLUE_B_REG_FLR_REQUEST_VF_63_32 0x901c 3036 /* [R 32] FLR request attention dirty bits for VFs 64 to 95. Each bit 3037 * indicates that the FLR register of the corresponding VF was set. Set by 3038 * PXP. Reset by MCP writing 1 to flr_request_vf_95_64_clr. */ 3039 #define PGLUE_B_REG_FLR_REQUEST_VF_95_64 0x9020 3040 /* [R 8] Each bit indicates an incorrect behavior in user RX interface. Bit 3041 * 0 - Target memory read arrived with a correctable error. Bit 1 - Target 3042 * memory read arrived with an uncorrectable error. Bit 2 - Configuration RW 3043 * arrived with a correctable error. Bit 3 - Configuration RW arrived with 3044 * an uncorrectable error. Bit 4 - Completion with Configuration Request 3045 * Retry Status. Bit 5 - Expansion ROM access received with a write request. 3046 * Bit 6 - Completion with pcie_rx_err of 0000; CMPL_STATUS of non-zero; and 3047 * pcie_rx_last not asserted. Bit 7 - Completion with pcie_rx_err of 1010; 3048 * and pcie_rx_last not asserted. */ 3049 #define PGLUE_B_REG_INCORRECT_RCV_DETAILS 0x9068 3050 #define PGLUE_B_REG_INTERNAL_PFID_ENABLE_MASTER 0x942c 3051 #define PGLUE_B_REG_INTERNAL_PFID_ENABLE_TARGET_READ 0x9430 3052 #define PGLUE_B_REG_INTERNAL_PFID_ENABLE_TARGET_WRITE 0x9434 3053 #define PGLUE_B_REG_INTERNAL_VFID_ENABLE 0x9438 3054 /* [W 7] Writing 1 to each bit in this register clears a corresponding error 3055 * details register and enables logging new error details. Bit 0 - clears 3056 * INCORRECT_RCV_DETAILS; Bit 1 - clears RX_ERR_DETAILS; Bit 2 - clears 3057 * TX_ERR_WR_ADD_31_0 TX_ERR_WR_ADD_63_32 TX_ERR_WR_DETAILS 3058 * TX_ERR_WR_DETAILS2 TX_ERR_RD_ADD_31_0 TX_ERR_RD_ADD_63_32 3059 * TX_ERR_RD_DETAILS TX_ERR_RD_DETAILS2 TX_ERR_WR_DETAILS_ICPL; Bit 3 - 3060 * clears VF_LENGTH_VIOLATION_DETAILS. Bit 4 - clears 3061 * VF_GRC_SPACE_VIOLATION_DETAILS. Bit 5 - clears RX_TCPL_ERR_DETAILS. Bit 6 3062 * - clears TCPL_IN_TWO_RCBS_DETAILS. */ 3063 #define PGLUE_B_REG_LATCHED_ERRORS_CLR 0x943c 3064 3065 /* [R 9] Interrupt register #0 read */ 3066 #define PGLUE_B_REG_PGLUE_B_INT_STS 0x9298 3067 /* [RC 9] Interrupt register #0 read clear */ 3068 #define PGLUE_B_REG_PGLUE_B_INT_STS_CLR 0x929c 3069 /* [RW 2] Parity mask register #0 read/write */ 3070 #define PGLUE_B_REG_PGLUE_B_PRTY_MASK 0x92b4 3071 /* [R 2] Parity register #0 read */ 3072 #define PGLUE_B_REG_PGLUE_B_PRTY_STS 0x92a8 3073 /* [RC 2] Parity register #0 read clear */ 3074 #define PGLUE_B_REG_PGLUE_B_PRTY_STS_CLR 0x92ac 3075 /* [R 13] Details of first request received with error. [2:0] - PFID. [3] - 3076 * VF_VALID. [9:4] - VFID. [11:10] - Error Code - 0 - Indicates Completion 3077 * Timeout of a User Tx non-posted request. 1 - unsupported request. 2 - 3078 * completer abort. 3 - Illegal value for this field. [12] valid - indicates 3079 * if there was a completion error since the last time this register was 3080 * cleared. */ 3081 #define PGLUE_B_REG_RX_ERR_DETAILS 0x9080 3082 /* [R 18] Details of first ATS Translation Completion request received with 3083 * error. [2:0] - PFID. [3] - VF_VALID. [9:4] - VFID. [11:10] - Error Code - 3084 * 0 - Indicates Completion Timeout of a User Tx non-posted request. 1 - 3085 * unsupported request. 2 - completer abort. 3 - Illegal value for this 3086 * field. [16:12] - ATC OTB EntryID. [17] valid - indicates if there was a 3087 * completion error since the last time this register was cleared. */ 3088 #define PGLUE_B_REG_RX_TCPL_ERR_DETAILS 0x9084 3089 /* [W 8] Debug only - Shadow BME bits clear for PFs 0 to 7. MCP writes 1 to 3090 * a bit in this register in order to clear the corresponding bit in 3091 * shadow_bme_pf_7_0 register. MCP should never use this unless a 3092 * work-around is needed. Note: register contains bits from both paths. */ 3093 #define PGLUE_B_REG_SHADOW_BME_PF_7_0_CLR 0x9458 3094 /* [R 8] SR IOV disabled attention dirty bits. Each bit indicates that the 3095 * VF enable register of the corresponding PF is written to 0 and was 3096 * previously 1. Set by PXP. Reset by MCP writing 1 to 3097 * sr_iov_disabled_request_clr. Note: register contains bits from both 3098 * paths. */ 3099 #define PGLUE_B_REG_SR_IOV_DISABLED_REQUEST 0x9030 3100 /* [R 32] Indicates the status of tags 32-63. 0 - tags is used - read 3101 * completion did not return yet. 1 - tag is unused. Same functionality as 3102 * pxp2_registers_pgl_exp_rom_data2 for tags 0-31. */ 3103 #define PGLUE_B_REG_TAGS_63_32 0x9244 3104 /* [RW 1] Type A PF enable inbound interrupt table for TSDM. 0 - disable; 1 3105 * - enable. */ 3106 #define PGLUE_B_REG_TSDM_INB_INT_A_PF_ENABLE 0x9170 3107 /* [RW 16] Start offset of TSDM zone A (queue zone) in the internal RAM */ 3108 #define PGLUE_B_REG_TSDM_START_OFFSET_A 0x90c4 3109 /* [RW 16] Start offset of TSDM zone B (legacy zone) in the internal RAM */ 3110 #define PGLUE_B_REG_TSDM_START_OFFSET_B 0x90cc 3111 /* [RW 5] VF Shift of TSDM zone B (legacy zone) in the internal RAM */ 3112 #define PGLUE_B_REG_TSDM_VF_SHIFT_B 0x90d4 3113 /* [RW 1] 0 - Zone A size is 136x32B; 1 - Zone A size is 152x32B. */ 3114 #define PGLUE_B_REG_TSDM_ZONE_A_SIZE_PF 0x91a0 3115 /* [R 32] Address [31:0] of first read request not submitted due to error */ 3116 #define PGLUE_B_REG_TX_ERR_RD_ADD_31_0 0x9098 3117 /* [R 32] Address [63:32] of first read request not submitted due to error */ 3118 #define PGLUE_B_REG_TX_ERR_RD_ADD_63_32 0x909c 3119 /* [R 31] Details of first read request not submitted due to error. [4:0] 3120 * VQID. [5] TREQ. 1 - Indicates the request is a Translation Request. 3121 * [20:8] - Length in bytes. [23:21] - PFID. [24] - VF_VALID. [30:25] - 3122 * VFID. */ 3123 #define PGLUE_B_REG_TX_ERR_RD_DETAILS 0x90a0 3124 /* [R 26] Details of first read request not submitted due to error. [15:0] 3125 * Request ID. [19:16] client ID. [20] - last SR. [24:21] - Error type - 3126 * [21] - Indicates was_error was set; [22] - Indicates BME was cleared; 3127 * [23] - Indicates FID_enable was cleared; [24] - Indicates VF with parent 3128 * PF FLR_request or IOV_disable_request dirty bit is set. [25] valid - 3129 * indicates if there was a request not submitted due to error since the 3130 * last time this register was cleared. */ 3131 #define PGLUE_B_REG_TX_ERR_RD_DETAILS2 0x90a4 3132 /* [R 32] Address [31:0] of first write request not submitted due to error */ 3133 #define PGLUE_B_REG_TX_ERR_WR_ADD_31_0 0x9088 3134 /* [R 32] Address [63:32] of first write request not submitted due to error */ 3135 #define PGLUE_B_REG_TX_ERR_WR_ADD_63_32 0x908c 3136 /* [R 31] Details of first write request not submitted due to error. [4:0] 3137 * VQID. [20:8] - Length in bytes. [23:21] - PFID. [24] - VF_VALID. [30:25] 3138 * - VFID. */ 3139 #define PGLUE_B_REG_TX_ERR_WR_DETAILS 0x9090 3140 /* [R 26] Details of first write request not submitted due to error. [15:0] 3141 * Request ID. [19:16] client ID. [20] - last SR. [24:21] - Error type - 3142 * [21] - Indicates was_error was set; [22] - Indicates BME was cleared; 3143 * [23] - Indicates FID_enable was cleared; [24] - Indicates VF with parent 3144 * PF FLR_request or IOV_disable_request dirty bit is set. [25] valid - 3145 * indicates if there was a request not submitted due to error since the 3146 * last time this register was cleared. */ 3147 #define PGLUE_B_REG_TX_ERR_WR_DETAILS2 0x9094 3148 /* [RW 10] Type A PF/VF inbound interrupt table for USDM: bits[9:5]-mask; 3149 * its[4:0]-address relative to start_offset_a. Bits [1:0] can have any 3150 * value (Byte resolution address). */ 3151 #define PGLUE_B_REG_USDM_INB_INT_A_0 0x9128 3152 #define PGLUE_B_REG_USDM_INB_INT_A_1 0x912c 3153 #define PGLUE_B_REG_USDM_INB_INT_A_2 0x9130 3154 #define PGLUE_B_REG_USDM_INB_INT_A_3 0x9134 3155 #define PGLUE_B_REG_USDM_INB_INT_A_4 0x9138 3156 #define PGLUE_B_REG_USDM_INB_INT_A_5 0x913c 3157 #define PGLUE_B_REG_USDM_INB_INT_A_6 0x9140 3158 /* [RW 1] Type A PF enable inbound interrupt table for USDM. 0 - disable; 1 3159 * - enable. */ 3160 #define PGLUE_B_REG_USDM_INB_INT_A_PF_ENABLE 0x917c 3161 /* [RW 1] Type A VF enable inbound interrupt table for USDM. 0 - disable; 1 3162 * - enable. */ 3163 #define PGLUE_B_REG_USDM_INB_INT_A_VF_ENABLE 0x9180 3164 /* [RW 1] Type B VF enable inbound interrupt table for USDM. 0 - disable; 1 3165 * - enable. */ 3166 #define PGLUE_B_REG_USDM_INB_INT_B_VF_ENABLE 0x9184 3167 /* [RW 16] Start offset of USDM zone A (queue zone) in the internal RAM */ 3168 #define PGLUE_B_REG_USDM_START_OFFSET_A 0x90d8 3169 /* [RW 16] Start offset of USDM zone B (legacy zone) in the internal RAM */ 3170 #define PGLUE_B_REG_USDM_START_OFFSET_B 0x90e0 3171 /* [RW 5] VF Shift of USDM zone B (legacy zone) in the internal RAM */ 3172 #define PGLUE_B_REG_USDM_VF_SHIFT_B 0x90e8 3173 /* [RW 1] 0 - Zone A size is 136x32B; 1 - Zone A size is 152x32B. */ 3174 #define PGLUE_B_REG_USDM_ZONE_A_SIZE_PF 0x91a4 3175 /* [R 26] Details of first target VF request accessing VF GRC space that 3176 * failed permission check. [14:0] Address. [15] w_nr: 0 - Read; 1 - Write. 3177 * [21:16] VFID. [24:22] - PFID. [25] valid - indicates if there was a 3178 * request accessing VF GRC space that failed permission check since the 3179 * last time this register was cleared. Permission checks are: function 3180 * permission; R/W permission; address range permission. */ 3181 #define PGLUE_B_REG_VF_GRC_SPACE_VIOLATION_DETAILS 0x9234 3182 /* [R 31] Details of first target VF request with length violation (too many 3183 * DWs) accessing BAR0. [12:0] Address in DWs (bits [14:2] of byte address). 3184 * [14:13] BAR. [20:15] VFID. [23:21] - PFID. [29:24] - Length in DWs. [30] 3185 * valid - indicates if there was a request with length violation since the 3186 * last time this register was cleared. Length violations: length of more 3187 * than 2DWs; length of 2DWs and address not QW aligned; window is GRC and 3188 * length is more than 1 DW. */ 3189 #define PGLUE_B_REG_VF_LENGTH_VIOLATION_DETAILS 0x9230 3190 /* [R 8] Was_error indication dirty bits for PFs 0 to 7. Each bit indicates 3191 * that there was a completion with uncorrectable error for the 3192 * corresponding PF. Set by PXP. Reset by MCP writing 1 to 3193 * was_error_pf_7_0_clr. */ 3194 #define PGLUE_B_REG_WAS_ERROR_PF_7_0 0x907c 3195 /* [W 8] Was_error indication dirty bits clear for PFs 0 to 7. MCP writes 1 3196 * to a bit in this register in order to clear the corresponding bit in 3197 * flr_request_pf_7_0 register. */ 3198 #define PGLUE_B_REG_WAS_ERROR_PF_7_0_CLR 0x9470 3199 /* [R 32] Was_error indication dirty bits for VFs 96 to 127. Each bit 3200 * indicates that there was a completion with uncorrectable error for the 3201 * corresponding VF. Set by PXP. Reset by MCP writing 1 to 3202 * was_error_vf_127_96_clr. */ 3203 #define PGLUE_B_REG_WAS_ERROR_VF_127_96 0x9078 3204 /* [W 32] Was_error indication dirty bits clear for VFs 96 to 127. MCP 3205 * writes 1 to a bit in this register in order to clear the corresponding 3206 * bit in was_error_vf_127_96 register. */ 3207 #define PGLUE_B_REG_WAS_ERROR_VF_127_96_CLR 0x9474 3208 /* [R 32] Was_error indication dirty bits for VFs 0 to 31. Each bit 3209 * indicates that there was a completion with uncorrectable error for the 3210 * corresponding VF. Set by PXP. Reset by MCP writing 1 to 3211 * was_error_vf_31_0_clr. */ 3212 #define PGLUE_B_REG_WAS_ERROR_VF_31_0 0x906c 3213 /* [W 32] Was_error indication dirty bits clear for VFs 0 to 31. MCP writes 3214 * 1 to a bit in this register in order to clear the corresponding bit in 3215 * was_error_vf_31_0 register. */ 3216 #define PGLUE_B_REG_WAS_ERROR_VF_31_0_CLR 0x9478 3217 /* [R 32] Was_error indication dirty bits for VFs 32 to 63. Each bit 3218 * indicates that there was a completion with uncorrectable error for the 3219 * corresponding VF. Set by PXP. Reset by MCP writing 1 to 3220 * was_error_vf_63_32_clr. */ 3221 #define PGLUE_B_REG_WAS_ERROR_VF_63_32 0x9070 3222 /* [W 32] Was_error indication dirty bits clear for VFs 32 to 63. MCP writes 3223 * 1 to a bit in this register in order to clear the corresponding bit in 3224 * was_error_vf_63_32 register. */ 3225 #define PGLUE_B_REG_WAS_ERROR_VF_63_32_CLR 0x947c 3226 /* [R 32] Was_error indication dirty bits for VFs 64 to 95. Each bit 3227 * indicates that there was a completion with uncorrectable error for the 3228 * corresponding VF. Set by PXP. Reset by MCP writing 1 to 3229 * was_error_vf_95_64_clr. */ 3230 #define PGLUE_B_REG_WAS_ERROR_VF_95_64 0x9074 3231 /* [W 32] Was_error indication dirty bits clear for VFs 64 to 95. MCP writes 3232 * 1 to a bit in this register in order to clear the corresponding bit in 3233 * was_error_vf_95_64 register. */ 3234 #define PGLUE_B_REG_WAS_ERROR_VF_95_64_CLR 0x9480 3235 /* [RW 1] Type A PF enable inbound interrupt table for XSDM. 0 - disable; 1 3236 * - enable. */ 3237 #define PGLUE_B_REG_XSDM_INB_INT_A_PF_ENABLE 0x9188 3238 /* [RW 16] Start offset of XSDM zone A (queue zone) in the internal RAM */ 3239 #define PGLUE_B_REG_XSDM_START_OFFSET_A 0x90ec 3240 /* [RW 16] Start offset of XSDM zone B (legacy zone) in the internal RAM */ 3241 #define PGLUE_B_REG_XSDM_START_OFFSET_B 0x90f4 3242 /* [RW 5] VF Shift of XSDM zone B (legacy zone) in the internal RAM */ 3243 #define PGLUE_B_REG_XSDM_VF_SHIFT_B 0x90fc 3244 /* [RW 1] 0 - Zone A size is 136x32B; 1 - Zone A size is 152x32B. */ 3245 #define PGLUE_B_REG_XSDM_ZONE_A_SIZE_PF 0x91a8 3246 #define PRS_REG_A_PRSU_20 0x40134 3247 /* [R 8] debug only: CFC load request current credit. Transaction based. */ 3248 #define PRS_REG_CFC_LD_CURRENT_CREDIT 0x40164 3249 /* [R 8] debug only: CFC search request current credit. Transaction based. */ 3250 #define PRS_REG_CFC_SEARCH_CURRENT_CREDIT 0x40168 3251 /* [RW 6] The initial credit for the search message to the CFC interface. 3252 Credit is transaction based. */ 3253 #define PRS_REG_CFC_SEARCH_INITIAL_CREDIT 0x4011c 3254 /* [RW 24] CID for port 0 if no match */ 3255 #define PRS_REG_CID_PORT_0 0x400fc 3256 /* [RW 32] The CM header for flush message where 'load existed' bit in CFC 3257 load response is reset and packet type is 0. Used in packet start message 3258 to TCM. */ 3259 #define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_0 0x400dc 3260 #define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_1 0x400e0 3261 #define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_2 0x400e4 3262 #define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_3 0x400e8 3263 #define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_4 0x400ec 3264 #define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_5 0x400f0 3265 /* [RW 32] The CM header for flush message where 'load existed' bit in CFC 3266 load response is set and packet type is 0. Used in packet start message 3267 to TCM. */ 3268 #define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_0 0x400bc 3269 #define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_1 0x400c0 3270 #define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_2 0x400c4 3271 #define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_3 0x400c8 3272 #define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_4 0x400cc 3273 #define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_5 0x400d0 3274 /* [RW 32] The CM header for a match and packet type 1 for loopback port. 3275 Used in packet start message to TCM. */ 3276 #define PRS_REG_CM_HDR_LOOPBACK_TYPE_1 0x4009c 3277 #define PRS_REG_CM_HDR_LOOPBACK_TYPE_2 0x400a0 3278 #define PRS_REG_CM_HDR_LOOPBACK_TYPE_3 0x400a4 3279 #define PRS_REG_CM_HDR_LOOPBACK_TYPE_4 0x400a8 3280 /* [RW 32] The CM header for a match and packet type 0. Used in packet start 3281 message to TCM. */ 3282 #define PRS_REG_CM_HDR_TYPE_0 0x40078 3283 #define PRS_REG_CM_HDR_TYPE_1 0x4007c 3284 #define PRS_REG_CM_HDR_TYPE_2 0x40080 3285 #define PRS_REG_CM_HDR_TYPE_3 0x40084 3286 #define PRS_REG_CM_HDR_TYPE_4 0x40088 3287 /* [RW 32] The CM header in case there was not a match on the connection */ 3288 #define PRS_REG_CM_NO_MATCH_HDR 0x400b8 3289 /* [RW 1] Indicates if in e1hov mode. 0=non-e1hov mode; 1=e1hov mode. */ 3290 #define PRS_REG_E1HOV_MODE 0x401c8 3291 /* [RW 8] The 8-bit event ID for a match and packet type 1. Used in packet 3292 start message to TCM. */ 3293 #define PRS_REG_EVENT_ID_1 0x40054 3294 #define PRS_REG_EVENT_ID_2 0x40058 3295 #define PRS_REG_EVENT_ID_3 0x4005c 3296 /* [RW 16] The Ethernet type value for FCoE */ 3297 #define PRS_REG_FCOE_TYPE 0x401d0 3298 /* [RW 8] Context region for flush packet with packet type 0. Used in CFC 3299 load request message. */ 3300 #define PRS_REG_FLUSH_REGIONS_TYPE_0 0x40004 3301 #define PRS_REG_FLUSH_REGIONS_TYPE_1 0x40008 3302 #define PRS_REG_FLUSH_REGIONS_TYPE_2 0x4000c 3303 #define PRS_REG_FLUSH_REGIONS_TYPE_3 0x40010 3304 #define PRS_REG_FLUSH_REGIONS_TYPE_4 0x40014 3305 #define PRS_REG_FLUSH_REGIONS_TYPE_5 0x40018 3306 #define PRS_REG_FLUSH_REGIONS_TYPE_6 0x4001c 3307 #define PRS_REG_FLUSH_REGIONS_TYPE_7 0x40020 3308 /* [RW 6] Bit-map indicating which L2 hdrs may appear after the basic 3309 * Ethernet header. */ 3310 #define PRS_REG_HDRS_AFTER_BASIC 0x40238 3311 /* [RW 6] Bit-map indicating which L2 hdrs may appear after the basic 3312 * Ethernet header for port 0 packets. */ 3313 #define PRS_REG_HDRS_AFTER_BASIC_PORT_0 0x40270 3314 #define PRS_REG_HDRS_AFTER_BASIC_PORT_1 0x40290 3315 /* [R 6] Bit-map indicating which L2 hdrs may appear after L2 tag 0 */ 3316 #define PRS_REG_HDRS_AFTER_TAG_0 0x40248 3317 /* [RW 6] Bit-map indicating which L2 hdrs may appear after L2 tag 0 for 3318 * port 0 packets */ 3319 #define PRS_REG_HDRS_AFTER_TAG_0_PORT_0 0x40280 3320 #define PRS_REG_HDRS_AFTER_TAG_0_PORT_1 0x402a0 3321 /* [RW 4] The increment value to send in the CFC load request message */ 3322 #define PRS_REG_INC_VALUE 0x40048 3323 /* [RW 6] Bit-map indicating which headers must appear in the packet */ 3324 #define PRS_REG_MUST_HAVE_HDRS 0x40254 3325 /* [RW 6] Bit-map indicating which headers must appear in the packet for 3326 * port 0 packets */ 3327 #define PRS_REG_MUST_HAVE_HDRS_PORT_0 0x4028c 3328 #define PRS_REG_MUST_HAVE_HDRS_PORT_1 0x402ac 3329 #define PRS_REG_NIC_MODE 0x40138 3330 /* [RW 8] The 8-bit event ID for cases where there is no match on the 3331 connection. Used in packet start message to TCM. */ 3332 #define PRS_REG_NO_MATCH_EVENT_ID 0x40070 3333 /* [ST 24] The number of input CFC flush packets */ 3334 #define PRS_REG_NUM_OF_CFC_FLUSH_MESSAGES 0x40128 3335 /* [ST 32] The number of cycles the Parser halted its operation since it 3336 could not allocate the next serial number */ 3337 #define PRS_REG_NUM_OF_DEAD_CYCLES 0x40130 3338 /* [ST 24] The number of input packets */ 3339 #define PRS_REG_NUM_OF_PACKETS 0x40124 3340 /* [ST 24] The number of input transparent flush packets */ 3341 #define PRS_REG_NUM_OF_TRANSPARENT_FLUSH_MESSAGES 0x4012c 3342 /* [RW 8] Context region for received Ethernet packet with a match and 3343 packet type 0. Used in CFC load request message */ 3344 #define PRS_REG_PACKET_REGIONS_TYPE_0 0x40028 3345 #define PRS_REG_PACKET_REGIONS_TYPE_1 0x4002c 3346 #define PRS_REG_PACKET_REGIONS_TYPE_2 0x40030 3347 #define PRS_REG_PACKET_REGIONS_TYPE_3 0x40034 3348 #define PRS_REG_PACKET_REGIONS_TYPE_4 0x40038 3349 #define PRS_REG_PACKET_REGIONS_TYPE_5 0x4003c 3350 #define PRS_REG_PACKET_REGIONS_TYPE_6 0x40040 3351 #define PRS_REG_PACKET_REGIONS_TYPE_7 0x40044 3352 /* [R 2] debug only: Number of pending requests for CAC on port 0. */ 3353 #define PRS_REG_PENDING_BRB_CAC0_RQ 0x40174 3354 /* [R 2] debug only: Number of pending requests for header parsing. */ 3355 #define PRS_REG_PENDING_BRB_PRS_RQ 0x40170 3356 /* [R 1] Interrupt register #0 read */ 3357 #define PRS_REG_PRS_INT_STS 0x40188 3358 /* [RW 8] Parity mask register #0 read/write */ 3359 #define PRS_REG_PRS_PRTY_MASK 0x401a4 3360 /* [R 8] Parity register #0 read */ 3361 #define PRS_REG_PRS_PRTY_STS 0x40198 3362 /* [RC 8] Parity register #0 read clear */ 3363 #define PRS_REG_PRS_PRTY_STS_CLR 0x4019c 3364 /* [RW 8] Context region for pure acknowledge packets. Used in CFC load 3365 request message */ 3366 #define PRS_REG_PURE_REGIONS 0x40024 3367 /* [R 32] debug only: Serial number status lsb 32 bits. '1' indicates this 3368 serail number was released by SDM but cannot be used because a previous 3369 serial number was not released. */ 3370 #define PRS_REG_SERIAL_NUM_STATUS_LSB 0x40154 3371 /* [R 32] debug only: Serial number status msb 32 bits. '1' indicates this 3372 serail number was released by SDM but cannot be used because a previous 3373 serial number was not released. */ 3374 #define PRS_REG_SERIAL_NUM_STATUS_MSB 0x40158 3375 /* [R 4] debug only: SRC current credit. Transaction based. */ 3376 #define PRS_REG_SRC_CURRENT_CREDIT 0x4016c 3377 /* [RW 16] The Ethernet type value for L2 tag 0 */ 3378 #define PRS_REG_TAG_ETHERTYPE_0 0x401d4 3379 /* [RW 4] The length of the info field for L2 tag 0. The length is between 3380 * 2B and 14B; in 2B granularity */ 3381 #define PRS_REG_TAG_LEN_0 0x4022c 3382 /* [R 8] debug only: TCM current credit. Cycle based. */ 3383 #define PRS_REG_TCM_CURRENT_CREDIT 0x40160 3384 /* [R 8] debug only: TSDM current credit. Transaction based. */ 3385 #define PRS_REG_TSDM_CURRENT_CREDIT 0x4015c 3386 /* [RW 16] One of 8 values that should be compared to type in Ethernet 3387 * parsing. If there is a match; the field after Ethernet is the first VLAN. 3388 * Reset value is 0x8100 which is the standard VLAN type. Note that when 3389 * checking second VLAN; type is compared only to 0x8100. 3390 */ 3391 #define PRS_REG_VLAN_TYPE_0 0x401a8 3392 #define PXP2_PXP2_INT_MASK_0_REG_PGL_CPL_AFT (0x1<<19) 3393 #define PXP2_PXP2_INT_MASK_0_REG_PGL_CPL_OF (0x1<<20) 3394 #define PXP2_PXP2_INT_MASK_0_REG_PGL_PCIE_ATTN (0x1<<22) 3395 #define PXP2_PXP2_INT_MASK_0_REG_PGL_READ_BLOCKED (0x1<<23) 3396 #define PXP2_PXP2_INT_MASK_0_REG_PGL_WRITE_BLOCKED (0x1<<24) 3397 #define PXP2_PXP2_INT_STS_0_REG_WR_PGLUE_EOP_ERROR (0x1<<7) 3398 #define PXP2_PXP2_INT_STS_CLR_0_REG_WR_PGLUE_EOP_ERROR (0x1<<7) 3399 /* [R 6] Debug only: Number of used entries in the data FIFO */ 3400 #define PXP2_REG_HST_DATA_FIFO_STATUS 0x12047c 3401 /* [R 7] Debug only: Number of used entries in the header FIFO */ 3402 #define PXP2_REG_HST_HEADER_FIFO_STATUS 0x120478 3403 #define PXP2_REG_PGL_ADDR_88_F0 0x120534 3404 /* [R 32] GRC address for configuration access to PCIE config address 0x88. 3405 * any write to this PCIE address will cause a GRC write access to the 3406 * address that's in t this register */ 3407 #define PXP2_REG_PGL_ADDR_88_F1 0x120544 3408 #define PXP2_REG_PGL_ADDR_8C_F0 0x120538 3409 /* [R 32] GRC address for configuration access to PCIE config address 0x8c. 3410 * any write to this PCIE address will cause a GRC write access to the 3411 * address that's in t this register */ 3412 #define PXP2_REG_PGL_ADDR_8C_F1 0x120548 3413 #define PXP2_REG_PGL_ADDR_90_F0 0x12053c 3414 /* [R 32] GRC address for configuration access to PCIE config address 0x90. 3415 * any write to this PCIE address will cause a GRC write access to the 3416 * address that's in t this register */ 3417 #define PXP2_REG_PGL_ADDR_90_F1 0x12054c 3418 #define PXP2_REG_PGL_ADDR_94_F0 0x120540 3419 /* [R 32] GRC address for configuration access to PCIE config address 0x94. 3420 * any write to this PCIE address will cause a GRC write access to the 3421 * address that's in t this register */ 3422 #define PXP2_REG_PGL_ADDR_94_F1 0x120550 3423 #define PXP2_REG_PGL_CONTROL0 0x120490 3424 #define PXP2_REG_PGL_CONTROL1 0x120514 3425 #define PXP2_REG_PGL_DEBUG 0x120520 3426 /* [RW 32] third dword data of expansion rom request. this register is 3427 special. reading from it provides a vector outstanding read requests. if 3428 a bit is zero it means that a read request on the corresponding tag did 3429 not finish yet (not all completions have arrived for it) */ 3430 #define PXP2_REG_PGL_EXP_ROM2 0x120808 3431 /* [RW 32] Inbound interrupt table for CSDM: bits[31:16]-mask; 3432 its[15:0]-address */ 3433 #define PXP2_REG_PGL_INT_CSDM_0 0x1204f4 3434 #define PXP2_REG_PGL_INT_CSDM_1 0x1204f8 3435 #define PXP2_REG_PGL_INT_CSDM_2 0x1204fc 3436 #define PXP2_REG_PGL_INT_CSDM_3 0x120500 3437 #define PXP2_REG_PGL_INT_CSDM_4 0x120504 3438 #define PXP2_REG_PGL_INT_CSDM_5 0x120508 3439 #define PXP2_REG_PGL_INT_CSDM_6 0x12050c 3440 #define PXP2_REG_PGL_INT_CSDM_7 0x120510 3441 /* [RW 32] Inbound interrupt table for TSDM: bits[31:16]-mask; 3442 its[15:0]-address */ 3443 #define PXP2_REG_PGL_INT_TSDM_0 0x120494 3444 #define PXP2_REG_PGL_INT_TSDM_1 0x120498 3445 #define PXP2_REG_PGL_INT_TSDM_2 0x12049c 3446 #define PXP2_REG_PGL_INT_TSDM_3 0x1204a0 3447 #define PXP2_REG_PGL_INT_TSDM_4 0x1204a4 3448 #define PXP2_REG_PGL_INT_TSDM_5 0x1204a8 3449 #define PXP2_REG_PGL_INT_TSDM_6 0x1204ac 3450 #define PXP2_REG_PGL_INT_TSDM_7 0x1204b0 3451 /* [RW 32] Inbound interrupt table for USDM: bits[31:16]-mask; 3452 its[15:0]-address */ 3453 #define PXP2_REG_PGL_INT_USDM_0 0x1204b4 3454 #define PXP2_REG_PGL_INT_USDM_1 0x1204b8 3455 #define PXP2_REG_PGL_INT_USDM_2 0x1204bc 3456 #define PXP2_REG_PGL_INT_USDM_3 0x1204c0 3457 #define PXP2_REG_PGL_INT_USDM_4 0x1204c4 3458 #define PXP2_REG_PGL_INT_USDM_5 0x1204c8 3459 #define PXP2_REG_PGL_INT_USDM_6 0x1204cc 3460 #define PXP2_REG_PGL_INT_USDM_7 0x1204d0 3461 /* [RW 32] Inbound interrupt table for XSDM: bits[31:16]-mask; 3462 its[15:0]-address */ 3463 #define PXP2_REG_PGL_INT_XSDM_0 0x1204d4 3464 #define PXP2_REG_PGL_INT_XSDM_1 0x1204d8 3465 #define PXP2_REG_PGL_INT_XSDM_2 0x1204dc 3466 #define PXP2_REG_PGL_INT_XSDM_3 0x1204e0 3467 #define PXP2_REG_PGL_INT_XSDM_4 0x1204e4 3468 #define PXP2_REG_PGL_INT_XSDM_5 0x1204e8 3469 #define PXP2_REG_PGL_INT_XSDM_6 0x1204ec 3470 #define PXP2_REG_PGL_INT_XSDM_7 0x1204f0 3471 /* [RW 3] this field allows one function to pretend being another function 3472 when accessing any BAR mapped resource within the device. the value of 3473 the field is the number of the function that will be accessed 3474 effectively. after software write to this bit it must read it in order to 3475 know that the new value is updated */ 3476 #define PXP2_REG_PGL_PRETEND_FUNC_F0 0x120674 3477 #define PXP2_REG_PGL_PRETEND_FUNC_F1 0x120678 3478 #define PXP2_REG_PGL_PRETEND_FUNC_F2 0x12067c 3479 #define PXP2_REG_PGL_PRETEND_FUNC_F3 0x120680 3480 #define PXP2_REG_PGL_PRETEND_FUNC_F4 0x120684 3481 #define PXP2_REG_PGL_PRETEND_FUNC_F5 0x120688 3482 #define PXP2_REG_PGL_PRETEND_FUNC_F6 0x12068c 3483 #define PXP2_REG_PGL_PRETEND_FUNC_F7 0x120690 3484 /* [R 1] this bit indicates that a read request was blocked because of 3485 bus_master_en was deasserted */ 3486 #define PXP2_REG_PGL_READ_BLOCKED 0x120568 3487 #define PXP2_REG_PGL_TAGS_LIMIT 0x1205a8 3488 /* [R 18] debug only */ 3489 #define PXP2_REG_PGL_TXW_CDTS 0x12052c 3490 /* [R 1] this bit indicates that a write request was blocked because of 3491 bus_master_en was deasserted */ 3492 #define PXP2_REG_PGL_WRITE_BLOCKED 0x120564 3493 #define PXP2_REG_PSWRQ_BW_ADD1 0x1201c0 3494 #define PXP2_REG_PSWRQ_BW_ADD10 0x1201e4 3495 #define PXP2_REG_PSWRQ_BW_ADD11 0x1201e8 3496 #define PXP2_REG_PSWRQ_BW_ADD2 0x1201c4 3497 #define PXP2_REG_PSWRQ_BW_ADD28 0x120228 3498 #define PXP2_REG_PSWRQ_BW_ADD3 0x1201c8 3499 #define PXP2_REG_PSWRQ_BW_ADD6 0x1201d4 3500 #define PXP2_REG_PSWRQ_BW_ADD7 0x1201d8 3501 #define PXP2_REG_PSWRQ_BW_ADD8 0x1201dc 3502 #define PXP2_REG_PSWRQ_BW_ADD9 0x1201e0 3503 #define PXP2_REG_PSWRQ_BW_CREDIT 0x12032c 3504 #define PXP2_REG_PSWRQ_BW_L1 0x1202b0 3505 #define PXP2_REG_PSWRQ_BW_L10 0x1202d4 3506 #define PXP2_REG_PSWRQ_BW_L11 0x1202d8 3507 #define PXP2_REG_PSWRQ_BW_L2 0x1202b4 3508 #define PXP2_REG_PSWRQ_BW_L28 0x120318 3509 #define PXP2_REG_PSWRQ_BW_L3 0x1202b8 3510 #define PXP2_REG_PSWRQ_BW_L6 0x1202c4 3511 #define PXP2_REG_PSWRQ_BW_L7 0x1202c8 3512 #define PXP2_REG_PSWRQ_BW_L8 0x1202cc 3513 #define PXP2_REG_PSWRQ_BW_L9 0x1202d0 3514 #define PXP2_REG_PSWRQ_BW_RD 0x120324 3515 #define PXP2_REG_PSWRQ_BW_UB1 0x120238 3516 #define PXP2_REG_PSWRQ_BW_UB10 0x12025c 3517 #define PXP2_REG_PSWRQ_BW_UB11 0x120260 3518 #define PXP2_REG_PSWRQ_BW_UB2 0x12023c 3519 #define PXP2_REG_PSWRQ_BW_UB28 0x1202a0 3520 #define PXP2_REG_PSWRQ_BW_UB3 0x120240 3521 #define PXP2_REG_PSWRQ_BW_UB6 0x12024c 3522 #define PXP2_REG_PSWRQ_BW_UB7 0x120250 3523 #define PXP2_REG_PSWRQ_BW_UB8 0x120254 3524 #define PXP2_REG_PSWRQ_BW_UB9 0x120258 3525 #define PXP2_REG_PSWRQ_BW_WR 0x120328 3526 #define PXP2_REG_PSWRQ_CDU0_L2P 0x120000 3527 #define PXP2_REG_PSWRQ_QM0_L2P 0x120038 3528 #define PXP2_REG_PSWRQ_SRC0_L2P 0x120054 3529 #define PXP2_REG_PSWRQ_TM0_L2P 0x12001c 3530 #define PXP2_REG_PSWRQ_TSDM0_L2P 0x1200e0 3531 /* [RW 32] Interrupt mask register #0 read/write */ 3532 #define PXP2_REG_PXP2_INT_MASK_0 0x120578 3533 /* [R 32] Interrupt register #0 read */ 3534 #define PXP2_REG_PXP2_INT_STS_0 0x12056c 3535 #define PXP2_REG_PXP2_INT_STS_1 0x120608 3536 /* [RC 32] Interrupt register #0 read clear */ 3537 #define PXP2_REG_PXP2_INT_STS_CLR_0 0x120570 3538 /* [RW 32] Parity mask register #0 read/write */ 3539 #define PXP2_REG_PXP2_PRTY_MASK_0 0x120588 3540 #define PXP2_REG_PXP2_PRTY_MASK_1 0x120598 3541 /* [R 32] Parity register #0 read */ 3542 #define PXP2_REG_PXP2_PRTY_STS_0 0x12057c 3543 #define PXP2_REG_PXP2_PRTY_STS_1 0x12058c 3544 /* [RC 32] Parity register #0 read clear */ 3545 #define PXP2_REG_PXP2_PRTY_STS_CLR_0 0x120580 3546 #define PXP2_REG_PXP2_PRTY_STS_CLR_1 0x120590 3547 /* [R 1] Debug only: The 'almost full' indication from each fifo (gives 3548 indication about backpressure) */ 3549 #define PXP2_REG_RD_ALMOST_FULL_0 0x120424 3550 /* [R 8] Debug only: The blocks counter - number of unused block ids */ 3551 #define PXP2_REG_RD_BLK_CNT 0x120418 3552 /* [RW 8] Debug only: Total number of available blocks in Tetris Buffer. 3553 Must be bigger than 6. Normally should not be changed. */ 3554 #define PXP2_REG_RD_BLK_NUM_CFG 0x12040c 3555 /* [RW 2] CDU byte swapping mode configuration for master read requests */ 3556 #define PXP2_REG_RD_CDURD_SWAP_MODE 0x120404 3557 /* [RW 1] When '1'; inputs to the PSWRD block are ignored */ 3558 #define PXP2_REG_RD_DISABLE_INPUTS 0x120374 3559 /* [R 1] PSWRD internal memories initialization is done */ 3560 #define PXP2_REG_RD_INIT_DONE 0x120370 3561 /* [RW 8] The maximum number of blocks in Tetris Buffer that can be 3562 allocated for vq10 */ 3563 #define PXP2_REG_RD_MAX_BLKS_VQ10 0x1203a0 3564 /* [RW 8] The maximum number of blocks in Tetris Buffer that can be 3565 allocated for vq11 */ 3566 #define PXP2_REG_RD_MAX_BLKS_VQ11 0x1203a4 3567 /* [RW 8] The maximum number of blocks in Tetris Buffer that can be 3568 allocated for vq17 */ 3569 #define PXP2_REG_RD_MAX_BLKS_VQ17 0x1203bc 3570 /* [RW 8] The maximum number of blocks in Tetris Buffer that can be 3571 allocated for vq18 */ 3572 #define PXP2_REG_RD_MAX_BLKS_VQ18 0x1203c0 3573 /* [RW 8] The maximum number of blocks in Tetris Buffer that can be 3574 allocated for vq19 */ 3575 #define PXP2_REG_RD_MAX_BLKS_VQ19 0x1203c4 3576 /* [RW 8] The maximum number of blocks in Tetris Buffer that can be 3577 allocated for vq22 */ 3578 #define PXP2_REG_RD_MAX_BLKS_VQ22 0x1203d0 3579 /* [RW 8] The maximum number of blocks in Tetris Buffer that can be 3580 allocated for vq25 */ 3581 #define PXP2_REG_RD_MAX_BLKS_VQ25 0x1203dc 3582 /* [RW 8] The maximum number of blocks in Tetris Buffer that can be 3583 allocated for vq6 */ 3584 #define PXP2_REG_RD_MAX_BLKS_VQ6 0x120390 3585 /* [RW 8] The maximum number of blocks in Tetris Buffer that can be 3586 allocated for vq9 */ 3587 #define PXP2_REG_RD_MAX_BLKS_VQ9 0x12039c 3588 /* [RW 2] PBF byte swapping mode configuration for master read requests */ 3589 #define PXP2_REG_RD_PBF_SWAP_MODE 0x1203f4 3590 /* [R 1] Debug only: Indication if delivery ports are idle */ 3591 #define PXP2_REG_RD_PORT_IS_IDLE_0 0x12041c 3592 #define PXP2_REG_RD_PORT_IS_IDLE_1 0x120420 3593 /* [RW 2] QM byte swapping mode configuration for master read requests */ 3594 #define PXP2_REG_RD_QM_SWAP_MODE 0x1203f8 3595 /* [R 7] Debug only: The SR counter - number of unused sub request ids */ 3596 #define PXP2_REG_RD_SR_CNT 0x120414 3597 /* [RW 2] SRC byte swapping mode configuration for master read requests */ 3598 #define PXP2_REG_RD_SRC_SWAP_MODE 0x120400 3599 /* [RW 7] Debug only: Total number of available PCI read sub-requests. Must 3600 be bigger than 1. Normally should not be changed. */ 3601 #define PXP2_REG_RD_SR_NUM_CFG 0x120408 3602 /* [RW 1] Signals the PSWRD block to start initializing internal memories */ 3603 #define PXP2_REG_RD_START_INIT 0x12036c 3604 /* [RW 2] TM byte swapping mode configuration for master read requests */ 3605 #define PXP2_REG_RD_TM_SWAP_MODE 0x1203fc 3606 /* [RW 10] Bandwidth addition to VQ0 write requests */ 3607 #define PXP2_REG_RQ_BW_RD_ADD0 0x1201bc 3608 /* [RW 10] Bandwidth addition to VQ12 read requests */ 3609 #define PXP2_REG_RQ_BW_RD_ADD12 0x1201ec 3610 /* [RW 10] Bandwidth addition to VQ13 read requests */ 3611 #define PXP2_REG_RQ_BW_RD_ADD13 0x1201f0 3612 /* [RW 10] Bandwidth addition to VQ14 read requests */ 3613 #define PXP2_REG_RQ_BW_RD_ADD14 0x1201f4 3614 /* [RW 10] Bandwidth addition to VQ15 read requests */ 3615 #define PXP2_REG_RQ_BW_RD_ADD15 0x1201f8 3616 /* [RW 10] Bandwidth addition to VQ16 read requests */ 3617 #define PXP2_REG_RQ_BW_RD_ADD16 0x1201fc 3618 /* [RW 10] Bandwidth addition to VQ17 read requests */ 3619 #define PXP2_REG_RQ_BW_RD_ADD17 0x120200 3620 /* [RW 10] Bandwidth addition to VQ18 read requests */ 3621 #define PXP2_REG_RQ_BW_RD_ADD18 0x120204 3622 /* [RW 10] Bandwidth addition to VQ19 read requests */ 3623 #define PXP2_REG_RQ_BW_RD_ADD19 0x120208 3624 /* [RW 10] Bandwidth addition to VQ20 read requests */ 3625 #define PXP2_REG_RQ_BW_RD_ADD20 0x12020c 3626 /* [RW 10] Bandwidth addition to VQ22 read requests */ 3627 #define PXP2_REG_RQ_BW_RD_ADD22 0x120210 3628 /* [RW 10] Bandwidth addition to VQ23 read requests */ 3629 #define PXP2_REG_RQ_BW_RD_ADD23 0x120214 3630 /* [RW 10] Bandwidth addition to VQ24 read requests */ 3631 #define PXP2_REG_RQ_BW_RD_ADD24 0x120218 3632 /* [RW 10] Bandwidth addition to VQ25 read requests */ 3633 #define PXP2_REG_RQ_BW_RD_ADD25 0x12021c 3634 /* [RW 10] Bandwidth addition to VQ26 read requests */ 3635 #define PXP2_REG_RQ_BW_RD_ADD26 0x120220 3636 /* [RW 10] Bandwidth addition to VQ27 read requests */ 3637 #define PXP2_REG_RQ_BW_RD_ADD27 0x120224 3638 /* [RW 10] Bandwidth addition to VQ4 read requests */ 3639 #define PXP2_REG_RQ_BW_RD_ADD4 0x1201cc 3640 /* [RW 10] Bandwidth addition to VQ5 read requests */ 3641 #define PXP2_REG_RQ_BW_RD_ADD5 0x1201d0 3642 /* [RW 10] Bandwidth Typical L for VQ0 Read requests */ 3643 #define PXP2_REG_RQ_BW_RD_L0 0x1202ac 3644 /* [RW 10] Bandwidth Typical L for VQ12 Read requests */ 3645 #define PXP2_REG_RQ_BW_RD_L12 0x1202dc 3646 /* [RW 10] Bandwidth Typical L for VQ13 Read requests */ 3647 #define PXP2_REG_RQ_BW_RD_L13 0x1202e0 3648 /* [RW 10] Bandwidth Typical L for VQ14 Read requests */ 3649 #define PXP2_REG_RQ_BW_RD_L14 0x1202e4 3650 /* [RW 10] Bandwidth Typical L for VQ15 Read requests */ 3651 #define PXP2_REG_RQ_BW_RD_L15 0x1202e8 3652 /* [RW 10] Bandwidth Typical L for VQ16 Read requests */ 3653 #define PXP2_REG_RQ_BW_RD_L16 0x1202ec 3654 /* [RW 10] Bandwidth Typical L for VQ17 Read requests */ 3655 #define PXP2_REG_RQ_BW_RD_L17 0x1202f0 3656 /* [RW 10] Bandwidth Typical L for VQ18 Read requests */ 3657 #define PXP2_REG_RQ_BW_RD_L18 0x1202f4 3658 /* [RW 10] Bandwidth Typical L for VQ19 Read requests */ 3659 #define PXP2_REG_RQ_BW_RD_L19 0x1202f8 3660 /* [RW 10] Bandwidth Typical L for VQ20 Read requests */ 3661 #define PXP2_REG_RQ_BW_RD_L20 0x1202fc 3662 /* [RW 10] Bandwidth Typical L for VQ22 Read requests */ 3663 #define PXP2_REG_RQ_BW_RD_L22 0x120300 3664 /* [RW 10] Bandwidth Typical L for VQ23 Read requests */ 3665 #define PXP2_REG_RQ_BW_RD_L23 0x120304 3666 /* [RW 10] Bandwidth Typical L for VQ24 Read requests */ 3667 #define PXP2_REG_RQ_BW_RD_L24 0x120308 3668 /* [RW 10] Bandwidth Typical L for VQ25 Read requests */ 3669 #define PXP2_REG_RQ_BW_RD_L25 0x12030c 3670 /* [RW 10] Bandwidth Typical L for VQ26 Read requests */ 3671 #define PXP2_REG_RQ_BW_RD_L26 0x120310 3672 /* [RW 10] Bandwidth Typical L for VQ27 Read requests */ 3673 #define PXP2_REG_RQ_BW_RD_L27 0x120314 3674 /* [RW 10] Bandwidth Typical L for VQ4 Read requests */ 3675 #define PXP2_REG_RQ_BW_RD_L4 0x1202bc 3676 /* [RW 10] Bandwidth Typical L for VQ5 Read- currently not used */ 3677 #define PXP2_REG_RQ_BW_RD_L5 0x1202c0 3678 /* [RW 7] Bandwidth upper bound for VQ0 read requests */ 3679 #define PXP2_REG_RQ_BW_RD_UBOUND0 0x120234 3680 /* [RW 7] Bandwidth upper bound for VQ12 read requests */ 3681 #define PXP2_REG_RQ_BW_RD_UBOUND12 0x120264 3682 /* [RW 7] Bandwidth upper bound for VQ13 read requests */ 3683 #define PXP2_REG_RQ_BW_RD_UBOUND13 0x120268 3684 /* [RW 7] Bandwidth upper bound for VQ14 read requests */ 3685 #define PXP2_REG_RQ_BW_RD_UBOUND14 0x12026c 3686 /* [RW 7] Bandwidth upper bound for VQ15 read requests */ 3687 #define PXP2_REG_RQ_BW_RD_UBOUND15 0x120270 3688 /* [RW 7] Bandwidth upper bound for VQ16 read requests */ 3689 #define PXP2_REG_RQ_BW_RD_UBOUND16 0x120274 3690 /* [RW 7] Bandwidth upper bound for VQ17 read requests */ 3691 #define PXP2_REG_RQ_BW_RD_UBOUND17 0x120278 3692 /* [RW 7] Bandwidth upper bound for VQ18 read requests */ 3693 #define PXP2_REG_RQ_BW_RD_UBOUND18 0x12027c 3694 /* [RW 7] Bandwidth upper bound for VQ19 read requests */ 3695 #define PXP2_REG_RQ_BW_RD_UBOUND19 0x120280 3696 /* [RW 7] Bandwidth upper bound for VQ20 read requests */ 3697 #define PXP2_REG_RQ_BW_RD_UBOUND20 0x120284 3698 /* [RW 7] Bandwidth upper bound for VQ22 read requests */ 3699 #define PXP2_REG_RQ_BW_RD_UBOUND22 0x120288 3700 /* [RW 7] Bandwidth upper bound for VQ23 read requests */ 3701 #define PXP2_REG_RQ_BW_RD_UBOUND23 0x12028c 3702 /* [RW 7] Bandwidth upper bound for VQ24 read requests */ 3703 #define PXP2_REG_RQ_BW_RD_UBOUND24 0x120290 3704 /* [RW 7] Bandwidth upper bound for VQ25 read requests */ 3705 #define PXP2_REG_RQ_BW_RD_UBOUND25 0x120294 3706 /* [RW 7] Bandwidth upper bound for VQ26 read requests */ 3707 #define PXP2_REG_RQ_BW_RD_UBOUND26 0x120298 3708 /* [RW 7] Bandwidth upper bound for VQ27 read requests */ 3709 #define PXP2_REG_RQ_BW_RD_UBOUND27 0x12029c 3710 /* [RW 7] Bandwidth upper bound for VQ4 read requests */ 3711 #define PXP2_REG_RQ_BW_RD_UBOUND4 0x120244 3712 /* [RW 7] Bandwidth upper bound for VQ5 read requests */ 3713 #define PXP2_REG_RQ_BW_RD_UBOUND5 0x120248 3714 /* [RW 10] Bandwidth addition to VQ29 write requests */ 3715 #define PXP2_REG_RQ_BW_WR_ADD29 0x12022c 3716 /* [RW 10] Bandwidth addition to VQ30 write requests */ 3717 #define PXP2_REG_RQ_BW_WR_ADD30 0x120230 3718 /* [RW 10] Bandwidth Typical L for VQ29 Write requests */ 3719 #define PXP2_REG_RQ_BW_WR_L29 0x12031c 3720 /* [RW 10] Bandwidth Typical L for VQ30 Write requests */ 3721 #define PXP2_REG_RQ_BW_WR_L30 0x120320 3722 /* [RW 7] Bandwidth upper bound for VQ29 */ 3723 #define PXP2_REG_RQ_BW_WR_UBOUND29 0x1202a4 3724 /* [RW 7] Bandwidth upper bound for VQ30 */ 3725 #define PXP2_REG_RQ_BW_WR_UBOUND30 0x1202a8 3726 /* [RW 18] external first_mem_addr field in L2P table for CDU module port 0 */ 3727 #define PXP2_REG_RQ_CDU0_EFIRST_MEM_ADDR 0x120008 3728 /* [RW 2] Endian mode for cdu */ 3729 #define PXP2_REG_RQ_CDU_ENDIAN_M 0x1201a0 3730 #define PXP2_REG_RQ_CDU_FIRST_ILT 0x12061c 3731 #define PXP2_REG_RQ_CDU_LAST_ILT 0x120620 3732 /* [RW 3] page size in L2P table for CDU module; -4k; -8k; -16k; -32k; -64k; 3733 -128k */ 3734 #define PXP2_REG_RQ_CDU_P_SIZE 0x120018 3735 /* [R 1] 1' indicates that the requester has finished its internal 3736 configuration */ 3737 #define PXP2_REG_RQ_CFG_DONE 0x1201b4 3738 /* [RW 2] Endian mode for debug */ 3739 #define PXP2_REG_RQ_DBG_ENDIAN_M 0x1201a4 3740 /* [RW 1] When '1'; requests will enter input buffers but wont get out 3741 towards the glue */ 3742 #define PXP2_REG_RQ_DISABLE_INPUTS 0x120330 3743 /* [RW 4] Determines alignment of write SRs when a request is split into 3744 * several SRs. 0 - 8B aligned. 1 - 64B aligned. 2 - 128B aligned. 3 - 256B 3745 * aligned. 4 - 512B aligned. */ 3746 #define PXP2_REG_RQ_DRAM_ALIGN 0x1205b0 3747 /* [RW 4] Determines alignment of read SRs when a request is split into 3748 * several SRs. 0 - 8B aligned. 1 - 64B aligned. 2 - 128B aligned. 3 - 256B 3749 * aligned. 4 - 512B aligned. */ 3750 #define PXP2_REG_RQ_DRAM_ALIGN_RD 0x12092c 3751 /* [RW 1] when set the new alignment method (E2) will be applied; when reset 3752 * the original alignment method (E1 E1H) will be applied */ 3753 #define PXP2_REG_RQ_DRAM_ALIGN_SEL 0x120930 3754 /* [RW 1] If 1 ILT failiue will not result in ELT access; An interrupt will 3755 be asserted */ 3756 #define PXP2_REG_RQ_ELT_DISABLE 0x12066c 3757 /* [RW 2] Endian mode for hc */ 3758 #define PXP2_REG_RQ_HC_ENDIAN_M 0x1201a8 3759 /* [RW 1] when '0' ILT logic will work as in A0; otherwise B0; for back 3760 compatibility needs; Note that different registers are used per mode */ 3761 #define PXP2_REG_RQ_ILT_MODE 0x1205b4 3762 /* [WB 53] Onchip address table */ 3763 #define PXP2_REG_RQ_ONCHIP_AT 0x122000 3764 /* [WB 53] Onchip address table - B0 */ 3765 #define PXP2_REG_RQ_ONCHIP_AT_B0 0x128000 3766 /* [RW 13] Pending read limiter threshold; in Dwords */ 3767 #define PXP2_REG_RQ_PDR_LIMIT 0x12033c 3768 /* [RW 2] Endian mode for qm */ 3769 #define PXP2_REG_RQ_QM_ENDIAN_M 0x120194 3770 #define PXP2_REG_RQ_QM_FIRST_ILT 0x120634 3771 #define PXP2_REG_RQ_QM_LAST_ILT 0x120638 3772 /* [RW 3] page size in L2P table for QM module; -4k; -8k; -16k; -32k; -64k; 3773 -128k */ 3774 #define PXP2_REG_RQ_QM_P_SIZE 0x120050 3775 /* [RW 1] 1' indicates that the RBC has finished configuring the PSWRQ */ 3776 #define PXP2_REG_RQ_RBC_DONE 0x1201b0 3777 /* [RW 3] Max burst size filed for read requests port 0; 000 - 128B; 3778 001:256B; 010: 512B; 11:1K:100:2K; 01:4K */ 3779 #define PXP2_REG_RQ_RD_MBS0 0x120160 3780 /* [RW 3] Max burst size filed for read requests port 1; 000 - 128B; 3781 001:256B; 010: 512B; 11:1K:100:2K; 01:4K */ 3782 #define PXP2_REG_RQ_RD_MBS1 0x120168 3783 /* [RW 2] Endian mode for src */ 3784 #define PXP2_REG_RQ_SRC_ENDIAN_M 0x12019c 3785 #define PXP2_REG_RQ_SRC_FIRST_ILT 0x12063c 3786 #define PXP2_REG_RQ_SRC_LAST_ILT 0x120640 3787 /* [RW 3] page size in L2P table for SRC module; -4k; -8k; -16k; -32k; -64k; 3788 -128k */ 3789 #define PXP2_REG_RQ_SRC_P_SIZE 0x12006c 3790 /* [RW 2] Endian mode for tm */ 3791 #define PXP2_REG_RQ_TM_ENDIAN_M 0x120198 3792 #define PXP2_REG_RQ_TM_FIRST_ILT 0x120644 3793 #define PXP2_REG_RQ_TM_LAST_ILT 0x120648 3794 /* [RW 3] page size in L2P table for TM module; -4k; -8k; -16k; -32k; -64k; 3795 -128k */ 3796 #define PXP2_REG_RQ_TM_P_SIZE 0x120034 3797 /* [R 5] Number of entries in the ufifo; his fifo has l2p completions */ 3798 #define PXP2_REG_RQ_UFIFO_NUM_OF_ENTRY 0x12080c 3799 /* [RW 18] external first_mem_addr field in L2P table for USDM module port 0 */ 3800 #define PXP2_REG_RQ_USDM0_EFIRST_MEM_ADDR 0x120094 3801 /* [R 8] Number of entries occupied by vq 0 in pswrq memory */ 3802 #define PXP2_REG_RQ_VQ0_ENTRY_CNT 0x120810 3803 /* [R 8] Number of entries occupied by vq 10 in pswrq memory */ 3804 #define PXP2_REG_RQ_VQ10_ENTRY_CNT 0x120818 3805 /* [R 8] Number of entries occupied by vq 11 in pswrq memory */ 3806 #define PXP2_REG_RQ_VQ11_ENTRY_CNT 0x120820 3807 /* [R 8] Number of entries occupied by vq 12 in pswrq memory */ 3808 #define PXP2_REG_RQ_VQ12_ENTRY_CNT 0x120828 3809 /* [R 8] Number of entries occupied by vq 13 in pswrq memory */ 3810 #define PXP2_REG_RQ_VQ13_ENTRY_CNT 0x120830 3811 /* [R 8] Number of entries occupied by vq 14 in pswrq memory */ 3812 #define PXP2_REG_RQ_VQ14_ENTRY_CNT 0x120838 3813 /* [R 8] Number of entries occupied by vq 15 in pswrq memory */ 3814 #define PXP2_REG_RQ_VQ15_ENTRY_CNT 0x120840 3815 /* [R 8] Number of entries occupied by vq 16 in pswrq memory */ 3816 #define PXP2_REG_RQ_VQ16_ENTRY_CNT 0x120848 3817 /* [R 8] Number of entries occupied by vq 17 in pswrq memory */ 3818 #define PXP2_REG_RQ_VQ17_ENTRY_CNT 0x120850 3819 /* [R 8] Number of entries occupied by vq 18 in pswrq memory */ 3820 #define PXP2_REG_RQ_VQ18_ENTRY_CNT 0x120858 3821 /* [R 8] Number of entries occupied by vq 19 in pswrq memory */ 3822 #define PXP2_REG_RQ_VQ19_ENTRY_CNT 0x120860 3823 /* [R 8] Number of entries occupied by vq 1 in pswrq memory */ 3824 #define PXP2_REG_RQ_VQ1_ENTRY_CNT 0x120868 3825 /* [R 8] Number of entries occupied by vq 20 in pswrq memory */ 3826 #define PXP2_REG_RQ_VQ20_ENTRY_CNT 0x120870 3827 /* [R 8] Number of entries occupied by vq 21 in pswrq memory */ 3828 #define PXP2_REG_RQ_VQ21_ENTRY_CNT 0x120878 3829 /* [R 8] Number of entries occupied by vq 22 in pswrq memory */ 3830 #define PXP2_REG_RQ_VQ22_ENTRY_CNT 0x120880 3831 /* [R 8] Number of entries occupied by vq 23 in pswrq memory */ 3832 #define PXP2_REG_RQ_VQ23_ENTRY_CNT 0x120888 3833 /* [R 8] Number of entries occupied by vq 24 in pswrq memory */ 3834 #define PXP2_REG_RQ_VQ24_ENTRY_CNT 0x120890 3835 /* [R 8] Number of entries occupied by vq 25 in pswrq memory */ 3836 #define PXP2_REG_RQ_VQ25_ENTRY_CNT 0x120898 3837 /* [R 8] Number of entries occupied by vq 26 in pswrq memory */ 3838 #define PXP2_REG_RQ_VQ26_ENTRY_CNT 0x1208a0 3839 /* [R 8] Number of entries occupied by vq 27 in pswrq memory */ 3840 #define PXP2_REG_RQ_VQ27_ENTRY_CNT 0x1208a8 3841 /* [R 8] Number of entries occupied by vq 28 in pswrq memory */ 3842 #define PXP2_REG_RQ_VQ28_ENTRY_CNT 0x1208b0 3843 /* [R 8] Number of entries occupied by vq 29 in pswrq memory */ 3844 #define PXP2_REG_RQ_VQ29_ENTRY_CNT 0x1208b8 3845 /* [R 8] Number of entries occupied by vq 2 in pswrq memory */ 3846 #define PXP2_REG_RQ_VQ2_ENTRY_CNT 0x1208c0 3847 /* [R 8] Number of entries occupied by vq 30 in pswrq memory */ 3848 #define PXP2_REG_RQ_VQ30_ENTRY_CNT 0x1208c8 3849 /* [R 8] Number of entries occupied by vq 31 in pswrq memory */ 3850 #define PXP2_REG_RQ_VQ31_ENTRY_CNT 0x1208d0 3851 /* [R 8] Number of entries occupied by vq 3 in pswrq memory */ 3852 #define PXP2_REG_RQ_VQ3_ENTRY_CNT 0x1208d8 3853 /* [R 8] Number of entries occupied by vq 4 in pswrq memory */ 3854 #define PXP2_REG_RQ_VQ4_ENTRY_CNT 0x1208e0 3855 /* [R 8] Number of entries occupied by vq 5 in pswrq memory */ 3856 #define PXP2_REG_RQ_VQ5_ENTRY_CNT 0x1208e8 3857 /* [R 8] Number of entries occupied by vq 6 in pswrq memory */ 3858 #define PXP2_REG_RQ_VQ6_ENTRY_CNT 0x1208f0 3859 /* [R 8] Number of entries occupied by vq 7 in pswrq memory */ 3860 #define PXP2_REG_RQ_VQ7_ENTRY_CNT 0x1208f8 3861 /* [R 8] Number of entries occupied by vq 8 in pswrq memory */ 3862 #define PXP2_REG_RQ_VQ8_ENTRY_CNT 0x120900 3863 /* [R 8] Number of entries occupied by vq 9 in pswrq memory */ 3864 #define PXP2_REG_RQ_VQ9_ENTRY_CNT 0x120908 3865 /* [RW 3] Max burst size filed for write requests port 0; 000 - 128B; 3866 001:256B; 010: 512B; */ 3867 #define PXP2_REG_RQ_WR_MBS0 0x12015c 3868 /* [RW 3] Max burst size filed for write requests port 1; 000 - 128B; 3869 001:256B; 010: 512B; */ 3870 #define PXP2_REG_RQ_WR_MBS1 0x120164 3871 /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the 3872 buffer reaches this number has_payload will be asserted */ 3873 #define PXP2_REG_WR_CDU_MPS 0x1205f0 3874 /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the 3875 buffer reaches this number has_payload will be asserted */ 3876 #define PXP2_REG_WR_CSDM_MPS 0x1205d0 3877 /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the 3878 buffer reaches this number has_payload will be asserted */ 3879 #define PXP2_REG_WR_DBG_MPS 0x1205e8 3880 /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the 3881 buffer reaches this number has_payload will be asserted */ 3882 #define PXP2_REG_WR_DMAE_MPS 0x1205ec 3883 /* [RW 10] if Number of entries in dmae fifo will be higher than this 3884 threshold then has_payload indication will be asserted; the default value 3885 should be equal to > write MBS size! */ 3886 #define PXP2_REG_WR_DMAE_TH 0x120368 3887 /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the 3888 buffer reaches this number has_payload will be asserted */ 3889 #define PXP2_REG_WR_HC_MPS 0x1205c8 3890 /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the 3891 buffer reaches this number has_payload will be asserted */ 3892 #define PXP2_REG_WR_QM_MPS 0x1205dc 3893 /* [RW 1] 0 - working in A0 mode; - working in B0 mode */ 3894 #define PXP2_REG_WR_REV_MODE 0x120670 3895 /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the 3896 buffer reaches this number has_payload will be asserted */ 3897 #define PXP2_REG_WR_SRC_MPS 0x1205e4 3898 /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the 3899 buffer reaches this number has_payload will be asserted */ 3900 #define PXP2_REG_WR_TM_MPS 0x1205e0 3901 /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the 3902 buffer reaches this number has_payload will be asserted */ 3903 #define PXP2_REG_WR_TSDM_MPS 0x1205d4 3904 /* [RW 10] if Number of entries in usdmdp fifo will be higher than this 3905 threshold then has_payload indication will be asserted; the default value 3906 should be equal to > write MBS size! */ 3907 #define PXP2_REG_WR_USDMDP_TH 0x120348 3908 /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the 3909 buffer reaches this number has_payload will be asserted */ 3910 #define PXP2_REG_WR_USDM_MPS 0x1205cc 3911 /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the 3912 buffer reaches this number has_payload will be asserted */ 3913 #define PXP2_REG_WR_XSDM_MPS 0x1205d8 3914 /* [R 1] debug only: Indication if PSWHST arbiter is idle */ 3915 #define PXP_REG_HST_ARB_IS_IDLE 0x103004 3916 /* [R 8] debug only: A bit mask for all PSWHST arbiter clients. '1' means 3917 this client is waiting for the arbiter. */ 3918 #define PXP_REG_HST_CLIENTS_WAITING_TO_ARB 0x103008 3919 /* [RW 1] When 1; doorbells are discarded and not passed to doorbell queue 3920 block. Should be used for close the gates. */ 3921 #define PXP_REG_HST_DISCARD_DOORBELLS 0x1030a4 3922 /* [R 1] debug only: '1' means this PSWHST is discarding doorbells. This bit 3923 should update according to 'hst_discard_doorbells' register when the state 3924 machine is idle */ 3925 #define PXP_REG_HST_DISCARD_DOORBELLS_STATUS 0x1030a0 3926 /* [RW 1] When 1; new internal writes arriving to the block are discarded. 3927 Should be used for close the gates. */ 3928 #define PXP_REG_HST_DISCARD_INTERNAL_WRITES 0x1030a8 3929 /* [R 6] debug only: A bit mask for all PSWHST internal write clients. '1' 3930 means this PSWHST is discarding inputs from this client. Each bit should 3931 update according to 'hst_discard_internal_writes' register when the state 3932 machine is idle. */ 3933 #define PXP_REG_HST_DISCARD_INTERNAL_WRITES_STATUS 0x10309c 3934 /* [WB 160] Used for initialization of the inbound interrupts memory */ 3935 #define PXP_REG_HST_INBOUND_INT 0x103800 3936 /* [RW 7] Indirect access to the permission table. The fields are : {Valid; 3937 * VFID[5:0]} 3938 */ 3939 #define PXP_REG_HST_ZONE_PERMISSION_TABLE 0x103400 3940 /* [RW 32] Interrupt mask register #0 read/write */ 3941 #define PXP_REG_PXP_INT_MASK_0 0x103074 3942 #define PXP_REG_PXP_INT_MASK_1 0x103084 3943 /* [R 32] Interrupt register #0 read */ 3944 #define PXP_REG_PXP_INT_STS_0 0x103068 3945 #define PXP_REG_PXP_INT_STS_1 0x103078 3946 /* [RC 32] Interrupt register #0 read clear */ 3947 #define PXP_REG_PXP_INT_STS_CLR_0 0x10306c 3948 #define PXP_REG_PXP_INT_STS_CLR_1 0x10307c 3949 /* [RW 27] Parity mask register #0 read/write */ 3950 #define PXP_REG_PXP_PRTY_MASK 0x103094 3951 /* [R 26] Parity register #0 read */ 3952 #define PXP_REG_PXP_PRTY_STS 0x103088 3953 /* [RC 27] Parity register #0 read clear */ 3954 #define PXP_REG_PXP_PRTY_STS_CLR 0x10308c 3955 /* [RW 4] The activity counter initial increment value sent in the load 3956 request */ 3957 #define QM_REG_ACTCTRINITVAL_0 0x168040 3958 #define QM_REG_ACTCTRINITVAL_1 0x168044 3959 #define QM_REG_ACTCTRINITVAL_2 0x168048 3960 #define QM_REG_ACTCTRINITVAL_3 0x16804c 3961 /* [RW 32] The base logical address (in bytes) of each physical queue. The 3962 index I represents the physical queue number. The 12 lsbs are ignore and 3963 considered zero so practically there are only 20 bits in this register; 3964 queues 63-0 */ 3965 #define QM_REG_BASEADDR 0x168900 3966 /* [RW 32] The base logical address (in bytes) of each physical queue. The 3967 index I represents the physical queue number. The 12 lsbs are ignore and 3968 considered zero so practically there are only 20 bits in this register; 3969 queues 127-64 */ 3970 #define QM_REG_BASEADDR_EXT_A 0x16e100 3971 /* [RW 16] The byte credit cost for each task. This value is for both ports */ 3972 #define QM_REG_BYTECRDCOST 0x168234 3973 /* [RW 16] The initial byte credit value for both ports. */ 3974 #define QM_REG_BYTECRDINITVAL 0x168238 3975 /* [RW 32] A bit per physical queue. If the bit is cleared then the physical 3976 queue uses port 0 else it uses port 1; queues 31-0 */ 3977 #define QM_REG_BYTECRDPORT_LSB 0x168228 3978 /* [RW 32] A bit per physical queue. If the bit is cleared then the physical 3979 queue uses port 0 else it uses port 1; queues 95-64 */ 3980 #define QM_REG_BYTECRDPORT_LSB_EXT_A 0x16e520 3981 /* [RW 32] A bit per physical queue. If the bit is cleared then the physical 3982 queue uses port 0 else it uses port 1; queues 63-32 */ 3983 #define QM_REG_BYTECRDPORT_MSB 0x168224 3984 /* [RW 32] A bit per physical queue. If the bit is cleared then the physical 3985 queue uses port 0 else it uses port 1; queues 127-96 */ 3986 #define QM_REG_BYTECRDPORT_MSB_EXT_A 0x16e51c 3987 /* [RW 16] The byte credit value that if above the QM is considered almost 3988 full */ 3989 #define QM_REG_BYTECREDITAFULLTHR 0x168094 3990 /* [RW 4] The initial credit for interface */ 3991 #define QM_REG_CMINITCRD_0 0x1680cc 3992 #define QM_REG_BYTECRDCMDQ_0 0x16e6e8 3993 #define QM_REG_CMINITCRD_1 0x1680d0 3994 #define QM_REG_CMINITCRD_2 0x1680d4 3995 #define QM_REG_CMINITCRD_3 0x1680d8 3996 #define QM_REG_CMINITCRD_4 0x1680dc 3997 #define QM_REG_CMINITCRD_5 0x1680e0 3998 #define QM_REG_CMINITCRD_6 0x1680e4 3999 #define QM_REG_CMINITCRD_7 0x1680e8 4000 /* [RW 8] A mask bit per CM interface. If this bit is 0 then this interface 4001 is masked */ 4002 #define QM_REG_CMINTEN 0x1680ec 4003 /* [RW 12] A bit vector which indicates which one of the queues are tied to 4004 interface 0 */ 4005 #define QM_REG_CMINTVOQMASK_0 0x1681f4 4006 #define QM_REG_CMINTVOQMASK_1 0x1681f8 4007 #define QM_REG_CMINTVOQMASK_2 0x1681fc 4008 #define QM_REG_CMINTVOQMASK_3 0x168200 4009 #define QM_REG_CMINTVOQMASK_4 0x168204 4010 #define QM_REG_CMINTVOQMASK_5 0x168208 4011 #define QM_REG_CMINTVOQMASK_6 0x16820c 4012 #define QM_REG_CMINTVOQMASK_7 0x168210 4013 /* [RW 20] The number of connections divided by 16 which dictates the size 4014 of each queue which belongs to even function number. */ 4015 #define QM_REG_CONNNUM_0 0x168020 4016 /* [R 6] Keep the fill level of the fifo from write client 4 */ 4017 #define QM_REG_CQM_WRC_FIFOLVL 0x168018 4018 /* [RW 8] The context regions sent in the CFC load request */ 4019 #define QM_REG_CTXREG_0 0x168030 4020 #define QM_REG_CTXREG_1 0x168034 4021 #define QM_REG_CTXREG_2 0x168038 4022 #define QM_REG_CTXREG_3 0x16803c 4023 /* [RW 12] The VOQ mask used to select the VOQs which needs to be full for 4024 bypass enable */ 4025 #define QM_REG_ENBYPVOQMASK 0x16823c 4026 /* [RW 32] A bit mask per each physical queue. If a bit is set then the 4027 physical queue uses the byte credit; queues 31-0 */ 4028 #define QM_REG_ENBYTECRD_LSB 0x168220 4029 /* [RW 32] A bit mask per each physical queue. If a bit is set then the 4030 physical queue uses the byte credit; queues 95-64 */ 4031 #define QM_REG_ENBYTECRD_LSB_EXT_A 0x16e518 4032 /* [RW 32] A bit mask per each physical queue. If a bit is set then the 4033 physical queue uses the byte credit; queues 63-32 */ 4034 #define QM_REG_ENBYTECRD_MSB 0x16821c 4035 /* [RW 32] A bit mask per each physical queue. If a bit is set then the 4036 physical queue uses the byte credit; queues 127-96 */ 4037 #define QM_REG_ENBYTECRD_MSB_EXT_A 0x16e514 4038 /* [RW 4] If cleared then the secondary interface will not be served by the 4039 RR arbiter */ 4040 #define QM_REG_ENSEC 0x1680f0 4041 /* [RW 32] NA */ 4042 #define QM_REG_FUNCNUMSEL_LSB 0x168230 4043 /* [RW 32] NA */ 4044 #define QM_REG_FUNCNUMSEL_MSB 0x16822c 4045 /* [RW 32] A mask register to mask the Almost empty signals which will not 4046 be use for the almost empty indication to the HW block; queues 31:0 */ 4047 #define QM_REG_HWAEMPTYMASK_LSB 0x168218 4048 /* [RW 32] A mask register to mask the Almost empty signals which will not 4049 be use for the almost empty indication to the HW block; queues 95-64 */ 4050 #define QM_REG_HWAEMPTYMASK_LSB_EXT_A 0x16e510 4051 /* [RW 32] A mask register to mask the Almost empty signals which will not 4052 be use for the almost empty indication to the HW block; queues 63:32 */ 4053 #define QM_REG_HWAEMPTYMASK_MSB 0x168214 4054 /* [RW 32] A mask register to mask the Almost empty signals which will not 4055 be use for the almost empty indication to the HW block; queues 127-96 */ 4056 #define QM_REG_HWAEMPTYMASK_MSB_EXT_A 0x16e50c 4057 /* [RW 4] The number of outstanding request to CFC */ 4058 #define QM_REG_OUTLDREQ 0x168804 4059 /* [RC 1] A flag to indicate that overflow error occurred in one of the 4060 queues. */ 4061 #define QM_REG_OVFERROR 0x16805c 4062 /* [RC 7] the Q where the overflow occurs */ 4063 #define QM_REG_OVFQNUM 0x168058 4064 /* [R 16] Pause state for physical queues 15-0 */ 4065 #define QM_REG_PAUSESTATE0 0x168410 4066 /* [R 16] Pause state for physical queues 31-16 */ 4067 #define QM_REG_PAUSESTATE1 0x168414 4068 /* [R 16] Pause state for physical queues 47-32 */ 4069 #define QM_REG_PAUSESTATE2 0x16e684 4070 /* [R 16] Pause state for physical queues 63-48 */ 4071 #define QM_REG_PAUSESTATE3 0x16e688 4072 /* [R 16] Pause state for physical queues 79-64 */ 4073 #define QM_REG_PAUSESTATE4 0x16e68c 4074 /* [R 16] Pause state for physical queues 95-80 */ 4075 #define QM_REG_PAUSESTATE5 0x16e690 4076 /* [R 16] Pause state for physical queues 111-96 */ 4077 #define QM_REG_PAUSESTATE6 0x16e694 4078 /* [R 16] Pause state for physical queues 127-112 */ 4079 #define QM_REG_PAUSESTATE7 0x16e698 4080 /* [RW 2] The PCI attributes field used in the PCI request. */ 4081 #define QM_REG_PCIREQAT 0x168054 4082 #define QM_REG_PF_EN 0x16e70c 4083 /* [R 24] The number of tasks stored in the QM for the PF. only even 4084 * functions are valid in E2 (odd I registers will be hard wired to 0) */ 4085 #define QM_REG_PF_USG_CNT_0 0x16e040 4086 /* [R 16] NOT USED */ 4087 #define QM_REG_PORT0BYTECRD 0x168300 4088 /* [R 16] The byte credit of port 1 */ 4089 #define QM_REG_PORT1BYTECRD 0x168304 4090 /* [RW 3] pci function number of queues 15-0 */ 4091 #define QM_REG_PQ2PCIFUNC_0 0x16e6bc 4092 #define QM_REG_PQ2PCIFUNC_1 0x16e6c0 4093 #define QM_REG_PQ2PCIFUNC_2 0x16e6c4 4094 #define QM_REG_PQ2PCIFUNC_3 0x16e6c8 4095 #define QM_REG_PQ2PCIFUNC_4 0x16e6cc 4096 #define QM_REG_PQ2PCIFUNC_5 0x16e6d0 4097 #define QM_REG_PQ2PCIFUNC_6 0x16e6d4 4098 #define QM_REG_PQ2PCIFUNC_7 0x16e6d8 4099 /* [WB 54] Pointer Table Memory for queues 63-0; The mapping is as follow: 4100 ptrtbl[53:30] read pointer; ptrtbl[29:6] write pointer; ptrtbl[5:4] read 4101 bank0; ptrtbl[3:2] read bank 1; ptrtbl[1:0] write bank; */ 4102 #define QM_REG_PTRTBL 0x168a00 4103 /* [WB 54] Pointer Table Memory for queues 127-64; The mapping is as follow: 4104 ptrtbl[53:30] read pointer; ptrtbl[29:6] write pointer; ptrtbl[5:4] read 4105 bank0; ptrtbl[3:2] read bank 1; ptrtbl[1:0] write bank; */ 4106 #define QM_REG_PTRTBL_EXT_A 0x16e200 4107 /* [RW 2] Interrupt mask register #0 read/write */ 4108 #define QM_REG_QM_INT_MASK 0x168444 4109 /* [R 2] Interrupt register #0 read */ 4110 #define QM_REG_QM_INT_STS 0x168438 4111 /* [RW 12] Parity mask register #0 read/write */ 4112 #define QM_REG_QM_PRTY_MASK 0x168454 4113 /* [R 12] Parity register #0 read */ 4114 #define QM_REG_QM_PRTY_STS 0x168448 4115 /* [RC 12] Parity register #0 read clear */ 4116 #define QM_REG_QM_PRTY_STS_CLR 0x16844c 4117 /* [R 32] Current queues in pipeline: Queues from 32 to 63 */ 4118 #define QM_REG_QSTATUS_HIGH 0x16802c 4119 /* [R 32] Current queues in pipeline: Queues from 96 to 127 */ 4120 #define QM_REG_QSTATUS_HIGH_EXT_A 0x16e408 4121 /* [R 32] Current queues in pipeline: Queues from 0 to 31 */ 4122 #define QM_REG_QSTATUS_LOW 0x168028 4123 /* [R 32] Current queues in pipeline: Queues from 64 to 95 */ 4124 #define QM_REG_QSTATUS_LOW_EXT_A 0x16e404 4125 /* [R 24] The number of tasks queued for each queue; queues 63-0 */ 4126 #define QM_REG_QTASKCTR_0 0x168308 4127 /* [R 24] The number of tasks queued for each queue; queues 127-64 */ 4128 #define QM_REG_QTASKCTR_EXT_A_0 0x16e584 4129 /* [RW 4] Queue tied to VOQ */ 4130 #define QM_REG_QVOQIDX_0 0x1680f4 4131 #define QM_REG_QVOQIDX_10 0x16811c 4132 #define QM_REG_QVOQIDX_100 0x16e49c 4133 #define QM_REG_QVOQIDX_101 0x16e4a0 4134 #define QM_REG_QVOQIDX_102 0x16e4a4 4135 #define QM_REG_QVOQIDX_103 0x16e4a8 4136 #define QM_REG_QVOQIDX_104 0x16e4ac 4137 #define QM_REG_QVOQIDX_105 0x16e4b0 4138 #define QM_REG_QVOQIDX_106 0x16e4b4 4139 #define QM_REG_QVOQIDX_107 0x16e4b8 4140 #define QM_REG_QVOQIDX_108 0x16e4bc 4141 #define QM_REG_QVOQIDX_109 0x16e4c0 4142 #define QM_REG_QVOQIDX_11 0x168120 4143 #define QM_REG_QVOQIDX_110 0x16e4c4 4144 #define QM_REG_QVOQIDX_111 0x16e4c8 4145 #define QM_REG_QVOQIDX_112 0x16e4cc 4146 #define QM_REG_QVOQIDX_113 0x16e4d0 4147 #define QM_REG_QVOQIDX_114 0x16e4d4 4148 #define QM_REG_QVOQIDX_115 0x16e4d8 4149 #define QM_REG_QVOQIDX_116 0x16e4dc 4150 #define QM_REG_QVOQIDX_117 0x16e4e0 4151 #define QM_REG_QVOQIDX_118 0x16e4e4 4152 #define QM_REG_QVOQIDX_119 0x16e4e8 4153 #define QM_REG_QVOQIDX_12 0x168124 4154 #define QM_REG_QVOQIDX_120 0x16e4ec 4155 #define QM_REG_QVOQIDX_121 0x16e4f0 4156 #define QM_REG_QVOQIDX_122 0x16e4f4 4157 #define QM_REG_QVOQIDX_123 0x16e4f8 4158 #define QM_REG_QVOQIDX_124 0x16e4fc 4159 #define QM_REG_QVOQIDX_125 0x16e500 4160 #define QM_REG_QVOQIDX_126 0x16e504 4161 #define QM_REG_QVOQIDX_127 0x16e508 4162 #define QM_REG_QVOQIDX_13 0x168128 4163 #define QM_REG_QVOQIDX_14 0x16812c 4164 #define QM_REG_QVOQIDX_15 0x168130 4165 #define QM_REG_QVOQIDX_16 0x168134 4166 #define QM_REG_QVOQIDX_17 0x168138 4167 #define QM_REG_QVOQIDX_21 0x168148 4168 #define QM_REG_QVOQIDX_22 0x16814c 4169 #define QM_REG_QVOQIDX_23 0x168150 4170 #define QM_REG_QVOQIDX_24 0x168154 4171 #define QM_REG_QVOQIDX_25 0x168158 4172 #define QM_REG_QVOQIDX_26 0x16815c 4173 #define QM_REG_QVOQIDX_27 0x168160 4174 #define QM_REG_QVOQIDX_28 0x168164 4175 #define QM_REG_QVOQIDX_29 0x168168 4176 #define QM_REG_QVOQIDX_30 0x16816c 4177 #define QM_REG_QVOQIDX_31 0x168170 4178 #define QM_REG_QVOQIDX_32 0x168174 4179 #define QM_REG_QVOQIDX_33 0x168178 4180 #define QM_REG_QVOQIDX_34 0x16817c 4181 #define QM_REG_QVOQIDX_35 0x168180 4182 #define QM_REG_QVOQIDX_36 0x168184 4183 #define QM_REG_QVOQIDX_37 0x168188 4184 #define QM_REG_QVOQIDX_38 0x16818c 4185 #define QM_REG_QVOQIDX_39 0x168190 4186 #define QM_REG_QVOQIDX_40 0x168194 4187 #define QM_REG_QVOQIDX_41 0x168198 4188 #define QM_REG_QVOQIDX_42 0x16819c 4189 #define QM_REG_QVOQIDX_43 0x1681a0 4190 #define QM_REG_QVOQIDX_44 0x1681a4 4191 #define QM_REG_QVOQIDX_45 0x1681a8 4192 #define QM_REG_QVOQIDX_46 0x1681ac 4193 #define QM_REG_QVOQIDX_47 0x1681b0 4194 #define QM_REG_QVOQIDX_48 0x1681b4 4195 #define QM_REG_QVOQIDX_49 0x1681b8 4196 #define QM_REG_QVOQIDX_5 0x168108 4197 #define QM_REG_QVOQIDX_50 0x1681bc 4198 #define QM_REG_QVOQIDX_51 0x1681c0 4199 #define QM_REG_QVOQIDX_52 0x1681c4 4200 #define QM_REG_QVOQIDX_53 0x1681c8 4201 #define QM_REG_QVOQIDX_54 0x1681cc 4202 #define QM_REG_QVOQIDX_55 0x1681d0 4203 #define QM_REG_QVOQIDX_56 0x1681d4 4204 #define QM_REG_QVOQIDX_57 0x1681d8 4205 #define QM_REG_QVOQIDX_58 0x1681dc 4206 #define QM_REG_QVOQIDX_59 0x1681e0 4207 #define QM_REG_QVOQIDX_6 0x16810c 4208 #define QM_REG_QVOQIDX_60 0x1681e4 4209 #define QM_REG_QVOQIDX_61 0x1681e8 4210 #define QM_REG_QVOQIDX_62 0x1681ec 4211 #define QM_REG_QVOQIDX_63 0x1681f0 4212 #define QM_REG_QVOQIDX_64 0x16e40c 4213 #define QM_REG_QVOQIDX_65 0x16e410 4214 #define QM_REG_QVOQIDX_69 0x16e420 4215 #define QM_REG_QVOQIDX_7 0x168110 4216 #define QM_REG_QVOQIDX_70 0x16e424 4217 #define QM_REG_QVOQIDX_71 0x16e428 4218 #define QM_REG_QVOQIDX_72 0x16e42c 4219 #define QM_REG_QVOQIDX_73 0x16e430 4220 #define QM_REG_QVOQIDX_74 0x16e434 4221 #define QM_REG_QVOQIDX_75 0x16e438 4222 #define QM_REG_QVOQIDX_76 0x16e43c 4223 #define QM_REG_QVOQIDX_77 0x16e440 4224 #define QM_REG_QVOQIDX_78 0x16e444 4225 #define QM_REG_QVOQIDX_79 0x16e448 4226 #define QM_REG_QVOQIDX_8 0x168114 4227 #define QM_REG_QVOQIDX_80 0x16e44c 4228 #define QM_REG_QVOQIDX_81 0x16e450 4229 #define QM_REG_QVOQIDX_85 0x16e460 4230 #define QM_REG_QVOQIDX_86 0x16e464 4231 #define QM_REG_QVOQIDX_87 0x16e468 4232 #define QM_REG_QVOQIDX_88 0x16e46c 4233 #define QM_REG_QVOQIDX_89 0x16e470 4234 #define QM_REG_QVOQIDX_9 0x168118 4235 #define QM_REG_QVOQIDX_90 0x16e474 4236 #define QM_REG_QVOQIDX_91 0x16e478 4237 #define QM_REG_QVOQIDX_92 0x16e47c 4238 #define QM_REG_QVOQIDX_93 0x16e480 4239 #define QM_REG_QVOQIDX_94 0x16e484 4240 #define QM_REG_QVOQIDX_95 0x16e488 4241 #define QM_REG_QVOQIDX_96 0x16e48c 4242 #define QM_REG_QVOQIDX_97 0x16e490 4243 #define QM_REG_QVOQIDX_98 0x16e494 4244 #define QM_REG_QVOQIDX_99 0x16e498 4245 /* [RW 1] Initialization bit command */ 4246 #define QM_REG_SOFT_RESET 0x168428 4247 /* [RW 8] The credit cost per every task in the QM. A value per each VOQ */ 4248 #define QM_REG_TASKCRDCOST_0 0x16809c 4249 #define QM_REG_TASKCRDCOST_1 0x1680a0 4250 #define QM_REG_TASKCRDCOST_2 0x1680a4 4251 #define QM_REG_TASKCRDCOST_4 0x1680ac 4252 #define QM_REG_TASKCRDCOST_5 0x1680b0 4253 /* [R 6] Keep the fill level of the fifo from write client 3 */ 4254 #define QM_REG_TQM_WRC_FIFOLVL 0x168010 4255 /* [R 6] Keep the fill level of the fifo from write client 2 */ 4256 #define QM_REG_UQM_WRC_FIFOLVL 0x168008 4257 /* [RC 32] Credit update error register */ 4258 #define QM_REG_VOQCRDERRREG 0x168408 4259 /* [R 16] The credit value for each VOQ */ 4260 #define QM_REG_VOQCREDIT_0 0x1682d0 4261 #define QM_REG_VOQCREDIT_1 0x1682d4 4262 #define QM_REG_VOQCREDIT_4 0x1682e0 4263 /* [RW 16] The credit value that if above the QM is considered almost full */ 4264 #define QM_REG_VOQCREDITAFULLTHR 0x168090 4265 /* [RW 16] The init and maximum credit for each VoQ */ 4266 #define QM_REG_VOQINITCREDIT_0 0x168060 4267 #define QM_REG_VOQINITCREDIT_1 0x168064 4268 #define QM_REG_VOQINITCREDIT_2 0x168068 4269 #define QM_REG_VOQINITCREDIT_4 0x168070 4270 #define QM_REG_VOQINITCREDIT_5 0x168074 4271 /* [RW 1] The port of which VOQ belongs */ 4272 #define QM_REG_VOQPORT_0 0x1682a0 4273 #define QM_REG_VOQPORT_1 0x1682a4 4274 #define QM_REG_VOQPORT_2 0x1682a8 4275 /* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */ 4276 #define QM_REG_VOQQMASK_0_LSB 0x168240 4277 /* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */ 4278 #define QM_REG_VOQQMASK_0_LSB_EXT_A 0x16e524 4279 /* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */ 4280 #define QM_REG_VOQQMASK_0_MSB 0x168244 4281 /* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */ 4282 #define QM_REG_VOQQMASK_0_MSB_EXT_A 0x16e528 4283 /* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */ 4284 #define QM_REG_VOQQMASK_10_LSB 0x168290 4285 /* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */ 4286 #define QM_REG_VOQQMASK_10_LSB_EXT_A 0x16e574 4287 /* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */ 4288 #define QM_REG_VOQQMASK_10_MSB 0x168294 4289 /* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */ 4290 #define QM_REG_VOQQMASK_10_MSB_EXT_A 0x16e578 4291 /* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */ 4292 #define QM_REG_VOQQMASK_11_LSB 0x168298 4293 /* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */ 4294 #define QM_REG_VOQQMASK_11_LSB_EXT_A 0x16e57c 4295 /* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */ 4296 #define QM_REG_VOQQMASK_11_MSB 0x16829c 4297 /* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */ 4298 #define QM_REG_VOQQMASK_11_MSB_EXT_A 0x16e580 4299 /* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */ 4300 #define QM_REG_VOQQMASK_1_LSB 0x168248 4301 /* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */ 4302 #define QM_REG_VOQQMASK_1_LSB_EXT_A 0x16e52c 4303 /* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */ 4304 #define QM_REG_VOQQMASK_1_MSB 0x16824c 4305 /* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */ 4306 #define QM_REG_VOQQMASK_1_MSB_EXT_A 0x16e530 4307 /* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */ 4308 #define QM_REG_VOQQMASK_2_LSB 0x168250 4309 /* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */ 4310 #define QM_REG_VOQQMASK_2_LSB_EXT_A 0x16e534 4311 /* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */ 4312 #define QM_REG_VOQQMASK_2_MSB 0x168254 4313 /* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */ 4314 #define QM_REG_VOQQMASK_2_MSB_EXT_A 0x16e538 4315 /* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */ 4316 #define QM_REG_VOQQMASK_3_LSB 0x168258 4317 /* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */ 4318 #define QM_REG_VOQQMASK_3_LSB_EXT_A 0x16e53c 4319 /* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */ 4320 #define QM_REG_VOQQMASK_3_MSB_EXT_A 0x16e540 4321 /* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */ 4322 #define QM_REG_VOQQMASK_4_LSB 0x168260 4323 /* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */ 4324 #define QM_REG_VOQQMASK_4_LSB_EXT_A 0x16e544 4325 /* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */ 4326 #define QM_REG_VOQQMASK_4_MSB 0x168264 4327 /* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */ 4328 #define QM_REG_VOQQMASK_4_MSB_EXT_A 0x16e548 4329 /* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */ 4330 #define QM_REG_VOQQMASK_5_LSB 0x168268 4331 /* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */ 4332 #define QM_REG_VOQQMASK_5_LSB_EXT_A 0x16e54c 4333 /* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */ 4334 #define QM_REG_VOQQMASK_5_MSB 0x16826c 4335 /* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */ 4336 #define QM_REG_VOQQMASK_5_MSB_EXT_A 0x16e550 4337 /* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */ 4338 #define QM_REG_VOQQMASK_6_LSB 0x168270 4339 /* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */ 4340 #define QM_REG_VOQQMASK_6_LSB_EXT_A 0x16e554 4341 /* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */ 4342 #define QM_REG_VOQQMASK_6_MSB 0x168274 4343 /* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */ 4344 #define QM_REG_VOQQMASK_6_MSB_EXT_A 0x16e558 4345 /* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */ 4346 #define QM_REG_VOQQMASK_7_LSB 0x168278 4347 /* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */ 4348 #define QM_REG_VOQQMASK_7_LSB_EXT_A 0x16e55c 4349 /* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */ 4350 #define QM_REG_VOQQMASK_7_MSB 0x16827c 4351 /* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */ 4352 #define QM_REG_VOQQMASK_7_MSB_EXT_A 0x16e560 4353 /* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */ 4354 #define QM_REG_VOQQMASK_8_LSB 0x168280 4355 /* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */ 4356 #define QM_REG_VOQQMASK_8_LSB_EXT_A 0x16e564 4357 /* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */ 4358 #define QM_REG_VOQQMASK_8_MSB 0x168284 4359 /* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */ 4360 #define QM_REG_VOQQMASK_8_MSB_EXT_A 0x16e568 4361 /* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */ 4362 #define QM_REG_VOQQMASK_9_LSB 0x168288 4363 /* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */ 4364 #define QM_REG_VOQQMASK_9_LSB_EXT_A 0x16e56c 4365 /* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */ 4366 #define QM_REG_VOQQMASK_9_MSB_EXT_A 0x16e570 4367 /* [RW 32] Wrr weights */ 4368 #define QM_REG_WRRWEIGHTS_0 0x16880c 4369 #define QM_REG_WRRWEIGHTS_1 0x168810 4370 #define QM_REG_WRRWEIGHTS_10 0x168814 4371 #define QM_REG_WRRWEIGHTS_11 0x168818 4372 #define QM_REG_WRRWEIGHTS_12 0x16881c 4373 #define QM_REG_WRRWEIGHTS_13 0x168820 4374 #define QM_REG_WRRWEIGHTS_14 0x168824 4375 #define QM_REG_WRRWEIGHTS_15 0x168828 4376 #define QM_REG_WRRWEIGHTS_16 0x16e000 4377 #define QM_REG_WRRWEIGHTS_17 0x16e004 4378 #define QM_REG_WRRWEIGHTS_18 0x16e008 4379 #define QM_REG_WRRWEIGHTS_19 0x16e00c 4380 #define QM_REG_WRRWEIGHTS_2 0x16882c 4381 #define QM_REG_WRRWEIGHTS_20 0x16e010 4382 #define QM_REG_WRRWEIGHTS_21 0x16e014 4383 #define QM_REG_WRRWEIGHTS_22 0x16e018 4384 #define QM_REG_WRRWEIGHTS_23 0x16e01c 4385 #define QM_REG_WRRWEIGHTS_24 0x16e020 4386 #define QM_REG_WRRWEIGHTS_25 0x16e024 4387 #define QM_REG_WRRWEIGHTS_26 0x16e028 4388 #define QM_REG_WRRWEIGHTS_27 0x16e02c 4389 #define QM_REG_WRRWEIGHTS_28 0x16e030 4390 #define QM_REG_WRRWEIGHTS_29 0x16e034 4391 #define QM_REG_WRRWEIGHTS_3 0x168830 4392 #define QM_REG_WRRWEIGHTS_30 0x16e038 4393 #define QM_REG_WRRWEIGHTS_31 0x16e03c 4394 #define QM_REG_WRRWEIGHTS_4 0x168834 4395 #define QM_REG_WRRWEIGHTS_5 0x168838 4396 #define QM_REG_WRRWEIGHTS_6 0x16883c 4397 #define QM_REG_WRRWEIGHTS_7 0x168840 4398 #define QM_REG_WRRWEIGHTS_8 0x168844 4399 #define QM_REG_WRRWEIGHTS_9 0x168848 4400 /* [R 6] Keep the fill level of the fifo from write client 1 */ 4401 #define QM_REG_XQM_WRC_FIFOLVL 0x168000 4402 /* [W 1] reset to parity interrupt */ 4403 #define SEM_FAST_REG_PARITY_RST 0x18840 4404 #define SRC_REG_COUNTFREE0 0x40500 4405 /* [RW 1] If clr the searcher is compatible to E1 A0 - support only two 4406 ports. If set the searcher support 8 functions. */ 4407 #define SRC_REG_E1HMF_ENABLE 0x404cc 4408 #define SRC_REG_FIRSTFREE0 0x40510 4409 #define SRC_REG_KEYRSS0_0 0x40408 4410 #define SRC_REG_KEYRSS0_7 0x40424 4411 #define SRC_REG_KEYRSS1_9 0x40454 4412 #define SRC_REG_KEYSEARCH_0 0x40458 4413 #define SRC_REG_KEYSEARCH_1 0x4045c 4414 #define SRC_REG_KEYSEARCH_2 0x40460 4415 #define SRC_REG_KEYSEARCH_3 0x40464 4416 #define SRC_REG_KEYSEARCH_4 0x40468 4417 #define SRC_REG_KEYSEARCH_5 0x4046c 4418 #define SRC_REG_KEYSEARCH_6 0x40470 4419 #define SRC_REG_KEYSEARCH_7 0x40474 4420 #define SRC_REG_KEYSEARCH_8 0x40478 4421 #define SRC_REG_KEYSEARCH_9 0x4047c 4422 #define SRC_REG_LASTFREE0 0x40530 4423 #define SRC_REG_NUMBER_HASH_BITS0 0x40400 4424 /* [RW 1] Reset internal state machines. */ 4425 #define SRC_REG_SOFT_RST 0x4049c 4426 /* [R 3] Interrupt register #0 read */ 4427 #define SRC_REG_SRC_INT_STS 0x404ac 4428 /* [RW 3] Parity mask register #0 read/write */ 4429 #define SRC_REG_SRC_PRTY_MASK 0x404c8 4430 /* [R 3] Parity register #0 read */ 4431 #define SRC_REG_SRC_PRTY_STS 0x404bc 4432 /* [RC 3] Parity register #0 read clear */ 4433 #define SRC_REG_SRC_PRTY_STS_CLR 0x404c0 4434 /* [R 4] Used to read the value of the XX protection CAM occupancy counter. */ 4435 #define TCM_REG_CAM_OCCUP 0x5017c 4436 /* [RW 1] CDU AG read Interface enable. If 0 - the request input is 4437 disregarded; valid output is deasserted; all other signals are treated as 4438 usual; if 1 - normal activity. */ 4439 #define TCM_REG_CDU_AG_RD_IFEN 0x50034 4440 /* [RW 1] CDU AG write Interface enable. If 0 - the request and valid input 4441 are disregarded; all other signals are treated as usual; if 1 - normal 4442 activity. */ 4443 #define TCM_REG_CDU_AG_WR_IFEN 0x50030 4444 /* [RW 1] CDU STORM read Interface enable. If 0 - the request input is 4445 disregarded; valid output is deasserted; all other signals are treated as 4446 usual; if 1 - normal activity. */ 4447 #define TCM_REG_CDU_SM_RD_IFEN 0x5003c 4448 /* [RW 1] CDU STORM write Interface enable. If 0 - the request and valid 4449 input is disregarded; all other signals are treated as usual; if 1 - 4450 normal activity. */ 4451 #define TCM_REG_CDU_SM_WR_IFEN 0x50038 4452 /* [RW 4] CFC output initial credit. Max credit available - 15.Write writes 4453 the initial credit value; read returns the current value of the credit 4454 counter. Must be initialized to 1 at start-up. */ 4455 #define TCM_REG_CFC_INIT_CRD 0x50204 4456 /* [RW 3] The weight of the CP input in the WRR mechanism. 0 stands for 4457 weight 8 (the most prioritised); 1 stands for weight 1(least 4458 prioritised); 2 stands for weight 2; tc. */ 4459 #define TCM_REG_CP_WEIGHT 0x500c0 4460 /* [RW 1] Input csem Interface enable. If 0 - the valid input is 4461 disregarded; acknowledge output is deasserted; all other signals are 4462 treated as usual; if 1 - normal activity. */ 4463 #define TCM_REG_CSEM_IFEN 0x5002c 4464 /* [RC 1] Message length mismatch (relative to last indication) at the In#9 4465 interface. */ 4466 #define TCM_REG_CSEM_LENGTH_MIS 0x50174 4467 /* [RW 3] The weight of the input csem in the WRR mechanism. 0 stands for 4468 weight 8 (the most prioritised); 1 stands for weight 1(least 4469 prioritised); 2 stands for weight 2; tc. */ 4470 #define TCM_REG_CSEM_WEIGHT 0x500bc 4471 /* [RW 8] The Event ID in case of ErrorFlg is set in the input message. */ 4472 #define TCM_REG_ERR_EVNT_ID 0x500a0 4473 /* [RW 28] The CM erroneous header for QM and Timers formatting. */ 4474 #define TCM_REG_ERR_TCM_HDR 0x5009c 4475 /* [RW 8] The Event ID for Timers expiration. */ 4476 #define TCM_REG_EXPR_EVNT_ID 0x500a4 4477 /* [RW 8] FIC0 output initial credit. Max credit available - 255.Write 4478 writes the initial credit value; read returns the current value of the 4479 credit counter. Must be initialized to 64 at start-up. */ 4480 #define TCM_REG_FIC0_INIT_CRD 0x5020c 4481 /* [RW 8] FIC1 output initial credit. Max credit available - 255.Write 4482 writes the initial credit value; read returns the current value of the 4483 credit counter. Must be initialized to 64 at start-up. */ 4484 #define TCM_REG_FIC1_INIT_CRD 0x50210 4485 /* [RW 1] Arbitration between Input Arbiter groups: 0 - fair Round-Robin; 1 4486 - strict priority defined by ~tcm_registers_gr_ag_pr.gr_ag_pr; 4487 ~tcm_registers_gr_ld0_pr.gr_ld0_pr and 4488 ~tcm_registers_gr_ld1_pr.gr_ld1_pr. */ 4489 #define TCM_REG_GR_ARB_TYPE 0x50114 4490 /* [RW 2] Load (FIC0) channel group priority. The lowest priority is 0; the 4491 highest priority is 3. It is supposed that the Store channel is the 4492 compliment of the other 3 groups. */ 4493 #define TCM_REG_GR_LD0_PR 0x5011c 4494 /* [RW 2] Load (FIC1) channel group priority. The lowest priority is 0; the 4495 highest priority is 3. It is supposed that the Store channel is the 4496 compliment of the other 3 groups. */ 4497 #define TCM_REG_GR_LD1_PR 0x50120 4498 /* [RW 4] The number of double REG-pairs; loaded from the STORM context and 4499 sent to STORM; for a specific connection type. The double REG-pairs are 4500 used to align to STORM context row size of 128 bits. The offset of these 4501 data in the STORM context is always 0. Index _i stands for the connection 4502 type (one of 16). */ 4503 #define TCM_REG_N_SM_CTX_LD_0 0x50050 4504 #define TCM_REG_N_SM_CTX_LD_1 0x50054 4505 #define TCM_REG_N_SM_CTX_LD_2 0x50058 4506 #define TCM_REG_N_SM_CTX_LD_3 0x5005c 4507 #define TCM_REG_N_SM_CTX_LD_4 0x50060 4508 #define TCM_REG_N_SM_CTX_LD_5 0x50064 4509 /* [RW 1] Input pbf Interface enable. If 0 - the valid input is disregarded; 4510 acknowledge output is deasserted; all other signals are treated as usual; 4511 if 1 - normal activity. */ 4512 #define TCM_REG_PBF_IFEN 0x50024 4513 /* [RC 1] Message length mismatch (relative to last indication) at the In#7 4514 interface. */ 4515 #define TCM_REG_PBF_LENGTH_MIS 0x5016c 4516 /* [RW 3] The weight of the input pbf in the WRR mechanism. 0 stands for 4517 weight 8 (the most prioritised); 1 stands for weight 1(least 4518 prioritised); 2 stands for weight 2; tc. */ 4519 #define TCM_REG_PBF_WEIGHT 0x500b4 4520 #define TCM_REG_PHYS_QNUM0_0 0x500e0 4521 #define TCM_REG_PHYS_QNUM0_1 0x500e4 4522 #define TCM_REG_PHYS_QNUM1_0 0x500e8 4523 #define TCM_REG_PHYS_QNUM1_1 0x500ec 4524 #define TCM_REG_PHYS_QNUM2_0 0x500f0 4525 #define TCM_REG_PHYS_QNUM2_1 0x500f4 4526 #define TCM_REG_PHYS_QNUM3_0 0x500f8 4527 #define TCM_REG_PHYS_QNUM3_1 0x500fc 4528 /* [RW 1] Input prs Interface enable. If 0 - the valid input is disregarded; 4529 acknowledge output is deasserted; all other signals are treated as usual; 4530 if 1 - normal activity. */ 4531 #define TCM_REG_PRS_IFEN 0x50020 4532 /* [RC 1] Message length mismatch (relative to last indication) at the In#6 4533 interface. */ 4534 #define TCM_REG_PRS_LENGTH_MIS 0x50168 4535 /* [RW 3] The weight of the input prs in the WRR mechanism. 0 stands for 4536 weight 8 (the most prioritised); 1 stands for weight 1(least 4537 prioritised); 2 stands for weight 2; tc. */ 4538 #define TCM_REG_PRS_WEIGHT 0x500b0 4539 /* [RW 8] The Event ID for Timers formatting in case of stop done. */ 4540 #define TCM_REG_STOP_EVNT_ID 0x500a8 4541 /* [RC 1] Message length mismatch (relative to last indication) at the STORM 4542 interface. */ 4543 #define TCM_REG_STORM_LENGTH_MIS 0x50160 4544 /* [RW 1] STORM - CM Interface enable. If 0 - the valid input is 4545 disregarded; acknowledge output is deasserted; all other signals are 4546 treated as usual; if 1 - normal activity. */ 4547 #define TCM_REG_STORM_TCM_IFEN 0x50010 4548 /* [RW 3] The weight of the STORM input in the WRR mechanism. 0 stands for 4549 weight 8 (the most prioritised); 1 stands for weight 1(least 4550 prioritised); 2 stands for weight 2; tc. */ 4551 #define TCM_REG_STORM_WEIGHT 0x500ac 4552 /* [RW 1] CM - CFC Interface enable. If 0 - the valid input is disregarded; 4553 acknowledge output is deasserted; all other signals are treated as usual; 4554 if 1 - normal activity. */ 4555 #define TCM_REG_TCM_CFC_IFEN 0x50040 4556 /* [RW 11] Interrupt mask register #0 read/write */ 4557 #define TCM_REG_TCM_INT_MASK 0x501dc 4558 /* [R 11] Interrupt register #0 read */ 4559 #define TCM_REG_TCM_INT_STS 0x501d0 4560 /* [RW 27] Parity mask register #0 read/write */ 4561 #define TCM_REG_TCM_PRTY_MASK 0x501ec 4562 /* [R 27] Parity register #0 read */ 4563 #define TCM_REG_TCM_PRTY_STS 0x501e0 4564 /* [RC 27] Parity register #0 read clear */ 4565 #define TCM_REG_TCM_PRTY_STS_CLR 0x501e4 4566 /* [RW 3] The size of AG context region 0 in REG-pairs. Designates the MS 4567 REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5). 4568 Is used to determine the number of the AG context REG-pairs written back; 4569 when the input message Reg1WbFlg isn't set. */ 4570 #define TCM_REG_TCM_REG0_SZ 0x500d8 4571 /* [RW 1] CM - STORM 0 Interface enable. If 0 - the acknowledge input is 4572 disregarded; valid is deasserted; all other signals are treated as usual; 4573 if 1 - normal activity. */ 4574 #define TCM_REG_TCM_STORM0_IFEN 0x50004 4575 /* [RW 1] CM - STORM 1 Interface enable. If 0 - the acknowledge input is 4576 disregarded; valid is deasserted; all other signals are treated as usual; 4577 if 1 - normal activity. */ 4578 #define TCM_REG_TCM_STORM1_IFEN 0x50008 4579 /* [RW 1] CM - QM Interface enable. If 0 - the acknowledge input is 4580 disregarded; valid is deasserted; all other signals are treated as usual; 4581 if 1 - normal activity. */ 4582 #define TCM_REG_TCM_TQM_IFEN 0x5000c 4583 /* [RW 1] If set the Q index; received from the QM is inserted to event ID. */ 4584 #define TCM_REG_TCM_TQM_USE_Q 0x500d4 4585 /* [RW 28] The CM header for Timers expiration command. */ 4586 #define TCM_REG_TM_TCM_HDR 0x50098 4587 /* [RW 1] Timers - CM Interface enable. If 0 - the valid input is 4588 disregarded; acknowledge output is deasserted; all other signals are 4589 treated as usual; if 1 - normal activity. */ 4590 #define TCM_REG_TM_TCM_IFEN 0x5001c 4591 /* [RW 3] The weight of the Timers input in the WRR mechanism. 0 stands for 4592 weight 8 (the most prioritised); 1 stands for weight 1(least 4593 prioritised); 2 stands for weight 2; tc. */ 4594 #define TCM_REG_TM_WEIGHT 0x500d0 4595 /* [RW 6] QM output initial credit. Max credit available - 32.Write writes 4596 the initial credit value; read returns the current value of the credit 4597 counter. Must be initialized to 32 at start-up. */ 4598 #define TCM_REG_TQM_INIT_CRD 0x5021c 4599 /* [RW 3] The weight of the QM (primary) input in the WRR mechanism. 0 4600 stands for weight 8 (the most prioritised); 1 stands for weight 1(least 4601 prioritised); 2 stands for weight 2; tc. */ 4602 #define TCM_REG_TQM_P_WEIGHT 0x500c8 4603 /* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0 4604 stands for weight 8 (the most prioritised); 1 stands for weight 1(least 4605 prioritised); 2 stands for weight 2; tc. */ 4606 #define TCM_REG_TQM_S_WEIGHT 0x500cc 4607 /* [RW 28] The CM header value for QM request (primary). */ 4608 #define TCM_REG_TQM_TCM_HDR_P 0x50090 4609 /* [RW 28] The CM header value for QM request (secondary). */ 4610 #define TCM_REG_TQM_TCM_HDR_S 0x50094 4611 /* [RW 1] QM - CM Interface enable. If 0 - the valid input is disregarded; 4612 acknowledge output is deasserted; all other signals are treated as usual; 4613 if 1 - normal activity. */ 4614 #define TCM_REG_TQM_TCM_IFEN 0x50014 4615 /* [RW 1] Input SDM Interface enable. If 0 - the valid input is disregarded; 4616 acknowledge output is deasserted; all other signals are treated as usual; 4617 if 1 - normal activity. */ 4618 #define TCM_REG_TSDM_IFEN 0x50018 4619 /* [RC 1] Message length mismatch (relative to last indication) at the SDM 4620 interface. */ 4621 #define TCM_REG_TSDM_LENGTH_MIS 0x50164 4622 /* [RW 3] The weight of the SDM input in the WRR mechanism. 0 stands for 4623 weight 8 (the most prioritised); 1 stands for weight 1(least 4624 prioritised); 2 stands for weight 2; tc. */ 4625 #define TCM_REG_TSDM_WEIGHT 0x500c4 4626 /* [RW 1] Input usem Interface enable. If 0 - the valid input is 4627 disregarded; acknowledge output is deasserted; all other signals are 4628 treated as usual; if 1 - normal activity. */ 4629 #define TCM_REG_USEM_IFEN 0x50028 4630 /* [RC 1] Message length mismatch (relative to last indication) at the In#8 4631 interface. */ 4632 #define TCM_REG_USEM_LENGTH_MIS 0x50170 4633 /* [RW 3] The weight of the input usem in the WRR mechanism. 0 stands for 4634 weight 8 (the most prioritised); 1 stands for weight 1(least 4635 prioritised); 2 stands for weight 2; tc. */ 4636 #define TCM_REG_USEM_WEIGHT 0x500b8 4637 /* [RW 21] Indirect access to the descriptor table of the XX protection 4638 mechanism. The fields are: [5:0] - length of the message; 15:6] - message 4639 pointer; 20:16] - next pointer. */ 4640 #define TCM_REG_XX_DESCR_TABLE 0x50280 4641 #define TCM_REG_XX_DESCR_TABLE_SIZE 29 4642 /* [R 6] Use to read the value of XX protection Free counter. */ 4643 #define TCM_REG_XX_FREE 0x50178 4644 /* [RW 6] Initial value for the credit counter; responsible for fulfilling 4645 of the Input Stage XX protection buffer by the XX protection pending 4646 messages. Max credit available - 127.Write writes the initial credit 4647 value; read returns the current value of the credit counter. Must be 4648 initialized to 19 at start-up. */ 4649 #define TCM_REG_XX_INIT_CRD 0x50220 4650 /* [RW 6] Maximum link list size (messages locked) per connection in the XX 4651 protection. */ 4652 #define TCM_REG_XX_MAX_LL_SZ 0x50044 4653 /* [RW 6] The maximum number of pending messages; which may be stored in XX 4654 protection. ~tcm_registers_xx_free.xx_free is read on read. */ 4655 #define TCM_REG_XX_MSG_NUM 0x50224 4656 /* [RW 8] The Event ID; sent to the STORM in case of XX overflow. */ 4657 #define TCM_REG_XX_OVFL_EVNT_ID 0x50048 4658 /* [RW 16] Indirect access to the XX table of the XX protection mechanism. 4659 The fields are:[4:0] - tail pointer; [10:5] - Link List size; 15:11] - 4660 header pointer. */ 4661 #define TCM_REG_XX_TABLE 0x50240 4662 /* [RW 4] Load value for cfc ac credit cnt. */ 4663 #define TM_REG_CFC_AC_CRDCNT_VAL 0x164208 4664 /* [RW 4] Load value for cfc cld credit cnt. */ 4665 #define TM_REG_CFC_CLD_CRDCNT_VAL 0x164210 4666 /* [RW 8] Client0 context region. */ 4667 #define TM_REG_CL0_CONT_REGION 0x164030 4668 /* [RW 8] Client1 context region. */ 4669 #define TM_REG_CL1_CONT_REGION 0x164034 4670 /* [RW 8] Client2 context region. */ 4671 #define TM_REG_CL2_CONT_REGION 0x164038 4672 /* [RW 2] Client in High priority client number. */ 4673 #define TM_REG_CLIN_PRIOR0_CLIENT 0x164024 4674 /* [RW 4] Load value for clout0 cred cnt. */ 4675 #define TM_REG_CLOUT_CRDCNT0_VAL 0x164220 4676 /* [RW 4] Load value for clout1 cred cnt. */ 4677 #define TM_REG_CLOUT_CRDCNT1_VAL 0x164228 4678 /* [RW 4] Load value for clout2 cred cnt. */ 4679 #define TM_REG_CLOUT_CRDCNT2_VAL 0x164230 4680 /* [RW 1] Enable client0 input. */ 4681 #define TM_REG_EN_CL0_INPUT 0x164008 4682 /* [RW 1] Enable client1 input. */ 4683 #define TM_REG_EN_CL1_INPUT 0x16400c 4684 /* [RW 1] Enable client2 input. */ 4685 #define TM_REG_EN_CL2_INPUT 0x164010 4686 #define TM_REG_EN_LINEAR0_TIMER 0x164014 4687 /* [RW 1] Enable real time counter. */ 4688 #define TM_REG_EN_REAL_TIME_CNT 0x1640d8 4689 /* [RW 1] Enable for Timers state machines. */ 4690 #define TM_REG_EN_TIMERS 0x164000 4691 /* [RW 4] Load value for expiration credit cnt. CFC max number of 4692 outstanding load requests for timers (expiration) context loading. */ 4693 #define TM_REG_EXP_CRDCNT_VAL 0x164238 4694 /* [RW 32] Linear0 logic address. */ 4695 #define TM_REG_LIN0_LOGIC_ADDR 0x164240 4696 /* [RW 18] Linear0 Max active cid (in banks of 32 entries). */ 4697 #define TM_REG_LIN0_MAX_ACTIVE_CID 0x164048 4698 /* [ST 16] Linear0 Number of scans counter. */ 4699 #define TM_REG_LIN0_NUM_SCANS 0x1640a0 4700 /* [WB 64] Linear0 phy address. */ 4701 #define TM_REG_LIN0_PHY_ADDR 0x164270 4702 /* [RW 1] Linear0 physical address valid. */ 4703 #define TM_REG_LIN0_PHY_ADDR_VALID 0x164248 4704 #define TM_REG_LIN0_SCAN_ON 0x1640d0 4705 /* [RW 24] Linear0 array scan timeout. */ 4706 #define TM_REG_LIN0_SCAN_TIME 0x16403c 4707 #define TM_REG_LIN0_VNIC_UC 0x164128 4708 /* [RW 32] Linear1 logic address. */ 4709 #define TM_REG_LIN1_LOGIC_ADDR 0x164250 4710 /* [WB 64] Linear1 phy address. */ 4711 #define TM_REG_LIN1_PHY_ADDR 0x164280 4712 /* [RW 1] Linear1 physical address valid. */ 4713 #define TM_REG_LIN1_PHY_ADDR_VALID 0x164258 4714 /* [RW 6] Linear timer set_clear fifo threshold. */ 4715 #define TM_REG_LIN_SETCLR_FIFO_ALFULL_THR 0x164070 4716 /* [RW 2] Load value for pci arbiter credit cnt. */ 4717 #define TM_REG_PCIARB_CRDCNT_VAL 0x164260 4718 /* [RW 20] The amount of hardware cycles for each timer tick. */ 4719 #define TM_REG_TIMER_TICK_SIZE 0x16401c 4720 /* [RW 8] Timers Context region. */ 4721 #define TM_REG_TM_CONTEXT_REGION 0x164044 4722 /* [RW 1] Interrupt mask register #0 read/write */ 4723 #define TM_REG_TM_INT_MASK 0x1640fc 4724 /* [R 1] Interrupt register #0 read */ 4725 #define TM_REG_TM_INT_STS 0x1640f0 4726 /* [RW 7] Parity mask register #0 read/write */ 4727 #define TM_REG_TM_PRTY_MASK 0x16410c 4728 /* [R 7] Parity register #0 read */ 4729 #define TM_REG_TM_PRTY_STS 0x164100 4730 /* [RC 7] Parity register #0 read clear */ 4731 #define TM_REG_TM_PRTY_STS_CLR 0x164104 4732 /* [RW 8] The event id for aggregated interrupt 0 */ 4733 #define TSDM_REG_AGG_INT_EVENT_0 0x42038 4734 #define TSDM_REG_AGG_INT_EVENT_1 0x4203c 4735 #define TSDM_REG_AGG_INT_EVENT_2 0x42040 4736 #define TSDM_REG_AGG_INT_EVENT_3 0x42044 4737 #define TSDM_REG_AGG_INT_EVENT_4 0x42048 4738 /* [RW 1] The T bit for aggregated interrupt 0 */ 4739 #define TSDM_REG_AGG_INT_T_0 0x420b8 4740 #define TSDM_REG_AGG_INT_T_1 0x420bc 4741 /* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */ 4742 #define TSDM_REG_CFC_RSP_START_ADDR 0x42008 4743 /* [RW 16] The maximum value of the completion counter #0 */ 4744 #define TSDM_REG_CMP_COUNTER_MAX0 0x4201c 4745 /* [RW 16] The maximum value of the completion counter #1 */ 4746 #define TSDM_REG_CMP_COUNTER_MAX1 0x42020 4747 /* [RW 16] The maximum value of the completion counter #2 */ 4748 #define TSDM_REG_CMP_COUNTER_MAX2 0x42024 4749 /* [RW 16] The maximum value of the completion counter #3 */ 4750 #define TSDM_REG_CMP_COUNTER_MAX3 0x42028 4751 /* [RW 13] The start address in the internal RAM for the completion 4752 counters. */ 4753 #define TSDM_REG_CMP_COUNTER_START_ADDR 0x4200c 4754 #define TSDM_REG_ENABLE_IN1 0x42238 4755 #define TSDM_REG_ENABLE_IN2 0x4223c 4756 #define TSDM_REG_ENABLE_OUT1 0x42240 4757 #define TSDM_REG_ENABLE_OUT2 0x42244 4758 /* [RW 4] The initial number of messages that can be sent to the pxp control 4759 interface without receiving any ACK. */ 4760 #define TSDM_REG_INIT_CREDIT_PXP_CTRL 0x424bc 4761 /* [ST 32] The number of ACK after placement messages received */ 4762 #define TSDM_REG_NUM_OF_ACK_AFTER_PLACE 0x4227c 4763 /* [ST 32] The number of packet end messages received from the parser */ 4764 #define TSDM_REG_NUM_OF_PKT_END_MSG 0x42274 4765 /* [ST 32] The number of requests received from the pxp async if */ 4766 #define TSDM_REG_NUM_OF_PXP_ASYNC_REQ 0x42278 4767 /* [ST 32] The number of commands received in queue 0 */ 4768 #define TSDM_REG_NUM_OF_Q0_CMD 0x42248 4769 /* [ST 32] The number of commands received in queue 10 */ 4770 #define TSDM_REG_NUM_OF_Q10_CMD 0x4226c 4771 /* [ST 32] The number of commands received in queue 11 */ 4772 #define TSDM_REG_NUM_OF_Q11_CMD 0x42270 4773 /* [ST 32] The number of commands received in queue 1 */ 4774 #define TSDM_REG_NUM_OF_Q1_CMD 0x4224c 4775 /* [ST 32] The number of commands received in queue 3 */ 4776 #define TSDM_REG_NUM_OF_Q3_CMD 0x42250 4777 /* [ST 32] The number of commands received in queue 4 */ 4778 #define TSDM_REG_NUM_OF_Q4_CMD 0x42254 4779 /* [ST 32] The number of commands received in queue 5 */ 4780 #define TSDM_REG_NUM_OF_Q5_CMD 0x42258 4781 /* [ST 32] The number of commands received in queue 6 */ 4782 #define TSDM_REG_NUM_OF_Q6_CMD 0x4225c 4783 /* [ST 32] The number of commands received in queue 7 */ 4784 #define TSDM_REG_NUM_OF_Q7_CMD 0x42260 4785 /* [ST 32] The number of commands received in queue 8 */ 4786 #define TSDM_REG_NUM_OF_Q8_CMD 0x42264 4787 /* [ST 32] The number of commands received in queue 9 */ 4788 #define TSDM_REG_NUM_OF_Q9_CMD 0x42268 4789 /* [RW 13] The start address in the internal RAM for the packet end message */ 4790 #define TSDM_REG_PCK_END_MSG_START_ADDR 0x42014 4791 /* [RW 13] The start address in the internal RAM for queue counters */ 4792 #define TSDM_REG_Q_COUNTER_START_ADDR 0x42010 4793 /* [R 1] pxp_ctrl rd_data fifo empty in sdm_dma_rsp block */ 4794 #define TSDM_REG_RSP_PXP_CTRL_RDATA_EMPTY 0x42548 4795 /* [R 1] parser fifo empty in sdm_sync block */ 4796 #define TSDM_REG_SYNC_PARSER_EMPTY 0x42550 4797 /* [R 1] parser serial fifo empty in sdm_sync block */ 4798 #define TSDM_REG_SYNC_SYNC_EMPTY 0x42558 4799 /* [RW 32] Tick for timer counter. Applicable only when 4800 ~tsdm_registers_timer_tick_enable.timer_tick_enable =1 */ 4801 #define TSDM_REG_TIMER_TICK 0x42000 4802 /* [RW 32] Interrupt mask register #0 read/write */ 4803 #define TSDM_REG_TSDM_INT_MASK_0 0x4229c 4804 #define TSDM_REG_TSDM_INT_MASK_1 0x422ac 4805 /* [R 32] Interrupt register #0 read */ 4806 #define TSDM_REG_TSDM_INT_STS_0 0x42290 4807 #define TSDM_REG_TSDM_INT_STS_1 0x422a0 4808 /* [RW 11] Parity mask register #0 read/write */ 4809 #define TSDM_REG_TSDM_PRTY_MASK 0x422bc 4810 /* [R 11] Parity register #0 read */ 4811 #define TSDM_REG_TSDM_PRTY_STS 0x422b0 4812 /* [RC 11] Parity register #0 read clear */ 4813 #define TSDM_REG_TSDM_PRTY_STS_CLR 0x422b4 4814 /* [RW 5] The number of time_slots in the arbitration cycle */ 4815 #define TSEM_REG_ARB_CYCLE_SIZE 0x180034 4816 /* [RW 3] The source that is associated with arbitration element 0. Source 4817 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 4818 sleeping thread with priority 1; 4- sleeping thread with priority 2 */ 4819 #define TSEM_REG_ARB_ELEMENT0 0x180020 4820 /* [RW 3] The source that is associated with arbitration element 1. Source 4821 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 4822 sleeping thread with priority 1; 4- sleeping thread with priority 2. 4823 Could not be equal to register ~tsem_registers_arb_element0.arb_element0 */ 4824 #define TSEM_REG_ARB_ELEMENT1 0x180024 4825 /* [RW 3] The source that is associated with arbitration element 2. Source 4826 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 4827 sleeping thread with priority 1; 4- sleeping thread with priority 2. 4828 Could not be equal to register ~tsem_registers_arb_element0.arb_element0 4829 and ~tsem_registers_arb_element1.arb_element1 */ 4830 #define TSEM_REG_ARB_ELEMENT2 0x180028 4831 /* [RW 3] The source that is associated with arbitration element 3. Source 4832 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 4833 sleeping thread with priority 1; 4- sleeping thread with priority 2.Could 4834 not be equal to register ~tsem_registers_arb_element0.arb_element0 and 4835 ~tsem_registers_arb_element1.arb_element1 and 4836 ~tsem_registers_arb_element2.arb_element2 */ 4837 #define TSEM_REG_ARB_ELEMENT3 0x18002c 4838 /* [RW 3] The source that is associated with arbitration element 4. Source 4839 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 4840 sleeping thread with priority 1; 4- sleeping thread with priority 2. 4841 Could not be equal to register ~tsem_registers_arb_element0.arb_element0 4842 and ~tsem_registers_arb_element1.arb_element1 and 4843 ~tsem_registers_arb_element2.arb_element2 and 4844 ~tsem_registers_arb_element3.arb_element3 */ 4845 #define TSEM_REG_ARB_ELEMENT4 0x180030 4846 #define TSEM_REG_ENABLE_IN 0x1800a4 4847 #define TSEM_REG_ENABLE_OUT 0x1800a8 4848 /* [RW 32] This address space contains all registers and memories that are 4849 placed in SEM_FAST block. The SEM_FAST registers are described in 4850 appendix B. In order to access the sem_fast registers the base address 4851 ~fast_memory.fast_memory should be added to eachsem_fast register offset. */ 4852 #define TSEM_REG_FAST_MEMORY 0x1a0000 4853 /* [RW 1] Disables input messages from FIC0 May be updated during run_time 4854 by the microcode */ 4855 #define TSEM_REG_FIC0_DISABLE 0x180224 4856 /* [RW 1] Disables input messages from FIC1 May be updated during run_time 4857 by the microcode */ 4858 #define TSEM_REG_FIC1_DISABLE 0x180234 4859 /* [RW 15] Interrupt table Read and write access to it is not possible in 4860 the middle of the work */ 4861 #define TSEM_REG_INT_TABLE 0x180400 4862 /* [ST 24] Statistics register. The number of messages that entered through 4863 FIC0 */ 4864 #define TSEM_REG_MSG_NUM_FIC0 0x180000 4865 /* [ST 24] Statistics register. The number of messages that entered through 4866 FIC1 */ 4867 #define TSEM_REG_MSG_NUM_FIC1 0x180004 4868 /* [ST 24] Statistics register. The number of messages that were sent to 4869 FOC0 */ 4870 #define TSEM_REG_MSG_NUM_FOC0 0x180008 4871 /* [ST 24] Statistics register. The number of messages that were sent to 4872 FOC1 */ 4873 #define TSEM_REG_MSG_NUM_FOC1 0x18000c 4874 /* [ST 24] Statistics register. The number of messages that were sent to 4875 FOC2 */ 4876 #define TSEM_REG_MSG_NUM_FOC2 0x180010 4877 /* [ST 24] Statistics register. The number of messages that were sent to 4878 FOC3 */ 4879 #define TSEM_REG_MSG_NUM_FOC3 0x180014 4880 /* [RW 1] Disables input messages from the passive buffer May be updated 4881 during run_time by the microcode */ 4882 #define TSEM_REG_PAS_DISABLE 0x18024c 4883 /* [WB 128] Debug only. Passive buffer memory */ 4884 #define TSEM_REG_PASSIVE_BUFFER 0x181000 4885 /* [WB 46] pram memory. B45 is parity; b[44:0] - data. */ 4886 #define TSEM_REG_PRAM 0x1c0000 4887 /* [R 8] Valid sleeping threads indication have bit per thread */ 4888 #define TSEM_REG_SLEEP_THREADS_VALID 0x18026c 4889 /* [R 1] EXT_STORE FIFO is empty in sem_slow_ls_ext */ 4890 #define TSEM_REG_SLOW_EXT_STORE_EMPTY 0x1802a0 4891 /* [RW 8] List of free threads . There is a bit per thread. */ 4892 #define TSEM_REG_THREADS_LIST 0x1802e4 4893 /* [RC 32] Parity register #0 read clear */ 4894 #define TSEM_REG_TSEM_PRTY_STS_CLR_0 0x180118 4895 #define TSEM_REG_TSEM_PRTY_STS_CLR_1 0x180128 4896 /* [RW 3] The arbitration scheme of time_slot 0 */ 4897 #define TSEM_REG_TS_0_AS 0x180038 4898 /* [RW 3] The arbitration scheme of time_slot 10 */ 4899 #define TSEM_REG_TS_10_AS 0x180060 4900 /* [RW 3] The arbitration scheme of time_slot 11 */ 4901 #define TSEM_REG_TS_11_AS 0x180064 4902 /* [RW 3] The arbitration scheme of time_slot 12 */ 4903 #define TSEM_REG_TS_12_AS 0x180068 4904 /* [RW 3] The arbitration scheme of time_slot 13 */ 4905 #define TSEM_REG_TS_13_AS 0x18006c 4906 /* [RW 3] The arbitration scheme of time_slot 14 */ 4907 #define TSEM_REG_TS_14_AS 0x180070 4908 /* [RW 3] The arbitration scheme of time_slot 15 */ 4909 #define TSEM_REG_TS_15_AS 0x180074 4910 /* [RW 3] The arbitration scheme of time_slot 16 */ 4911 #define TSEM_REG_TS_16_AS 0x180078 4912 /* [RW 3] The arbitration scheme of time_slot 17 */ 4913 #define TSEM_REG_TS_17_AS 0x18007c 4914 /* [RW 3] The arbitration scheme of time_slot 18 */ 4915 #define TSEM_REG_TS_18_AS 0x180080 4916 /* [RW 3] The arbitration scheme of time_slot 1 */ 4917 #define TSEM_REG_TS_1_AS 0x18003c 4918 /* [RW 3] The arbitration scheme of time_slot 2 */ 4919 #define TSEM_REG_TS_2_AS 0x180040 4920 /* [RW 3] The arbitration scheme of time_slot 3 */ 4921 #define TSEM_REG_TS_3_AS 0x180044 4922 /* [RW 3] The arbitration scheme of time_slot 4 */ 4923 #define TSEM_REG_TS_4_AS 0x180048 4924 /* [RW 3] The arbitration scheme of time_slot 5 */ 4925 #define TSEM_REG_TS_5_AS 0x18004c 4926 /* [RW 3] The arbitration scheme of time_slot 6 */ 4927 #define TSEM_REG_TS_6_AS 0x180050 4928 /* [RW 3] The arbitration scheme of time_slot 7 */ 4929 #define TSEM_REG_TS_7_AS 0x180054 4930 /* [RW 3] The arbitration scheme of time_slot 8 */ 4931 #define TSEM_REG_TS_8_AS 0x180058 4932 /* [RW 3] The arbitration scheme of time_slot 9 */ 4933 #define TSEM_REG_TS_9_AS 0x18005c 4934 /* [RW 32] Interrupt mask register #0 read/write */ 4935 #define TSEM_REG_TSEM_INT_MASK_0 0x180100 4936 #define TSEM_REG_TSEM_INT_MASK_1 0x180110 4937 /* [R 32] Interrupt register #0 read */ 4938 #define TSEM_REG_TSEM_INT_STS_0 0x1800f4 4939 #define TSEM_REG_TSEM_INT_STS_1 0x180104 4940 /* [RW 32] Parity mask register #0 read/write */ 4941 #define TSEM_REG_TSEM_PRTY_MASK_0 0x180120 4942 #define TSEM_REG_TSEM_PRTY_MASK_1 0x180130 4943 /* [R 32] Parity register #0 read */ 4944 #define TSEM_REG_TSEM_PRTY_STS_0 0x180114 4945 #define TSEM_REG_TSEM_PRTY_STS_1 0x180124 4946 /* [W 7] VF or PF ID for reset error bit. Values 0-63 reset error bit for 64 4947 * VF; values 64-67 reset error for 4 PF; values 68-127 are not valid. */ 4948 #define TSEM_REG_VFPF_ERR_NUM 0x180380 4949 /* [RW 32] Indirect access to AG context with 32-bits granularity. The bits 4950 * [10:8] of the address should be the offset within the accessed LCID 4951 * context; the bits [7:0] are the accessed LCID.Example: to write to REG10 4952 * LCID100. The RBC address should be 12'ha64. */ 4953 #define UCM_REG_AG_CTX 0xe2000 4954 /* [R 5] Used to read the XX protection CAM occupancy counter. */ 4955 #define UCM_REG_CAM_OCCUP 0xe0170 4956 /* [RW 1] CDU AG read Interface enable. If 0 - the request input is 4957 disregarded; valid output is deasserted; all other signals are treated as 4958 usual; if 1 - normal activity. */ 4959 #define UCM_REG_CDU_AG_RD_IFEN 0xe0038 4960 /* [RW 1] CDU AG write Interface enable. If 0 - the request and valid input 4961 are disregarded; all other signals are treated as usual; if 1 - normal 4962 activity. */ 4963 #define UCM_REG_CDU_AG_WR_IFEN 0xe0034 4964 /* [RW 1] CDU STORM read Interface enable. If 0 - the request input is 4965 disregarded; valid output is deasserted; all other signals are treated as 4966 usual; if 1 - normal activity. */ 4967 #define UCM_REG_CDU_SM_RD_IFEN 0xe0040 4968 /* [RW 1] CDU STORM write Interface enable. If 0 - the request and valid 4969 input is disregarded; all other signals are treated as usual; if 1 - 4970 normal activity. */ 4971 #define UCM_REG_CDU_SM_WR_IFEN 0xe003c 4972 /* [RW 4] CFC output initial credit. Max credit available - 15.Write writes 4973 the initial credit value; read returns the current value of the credit 4974 counter. Must be initialized to 1 at start-up. */ 4975 #define UCM_REG_CFC_INIT_CRD 0xe0204 4976 /* [RW 3] The weight of the CP input in the WRR mechanism. 0 stands for 4977 weight 8 (the most prioritised); 1 stands for weight 1(least 4978 prioritised); 2 stands for weight 2; tc. */ 4979 #define UCM_REG_CP_WEIGHT 0xe00c4 4980 /* [RW 1] Input csem Interface enable. If 0 - the valid input is 4981 disregarded; acknowledge output is deasserted; all other signals are 4982 treated as usual; if 1 - normal activity. */ 4983 #define UCM_REG_CSEM_IFEN 0xe0028 4984 /* [RC 1] Set when the message length mismatch (relative to last indication) 4985 at the csem interface is detected. */ 4986 #define UCM_REG_CSEM_LENGTH_MIS 0xe0160 4987 /* [RW 3] The weight of the input csem in the WRR mechanism. 0 stands for 4988 weight 8 (the most prioritised); 1 stands for weight 1(least 4989 prioritised); 2 stands for weight 2; tc. */ 4990 #define UCM_REG_CSEM_WEIGHT 0xe00b8 4991 /* [RW 1] Input dorq Interface enable. If 0 - the valid input is 4992 disregarded; acknowledge output is deasserted; all other signals are 4993 treated as usual; if 1 - normal activity. */ 4994 #define UCM_REG_DORQ_IFEN 0xe0030 4995 /* [RC 1] Set when the message length mismatch (relative to last indication) 4996 at the dorq interface is detected. */ 4997 #define UCM_REG_DORQ_LENGTH_MIS 0xe0168 4998 /* [RW 3] The weight of the input dorq in the WRR mechanism. 0 stands for 4999 weight 8 (the most prioritised); 1 stands for weight 1(least 5000 prioritised); 2 stands for weight 2; tc. */ 5001 #define UCM_REG_DORQ_WEIGHT 0xe00c0 5002 /* [RW 8] The Event ID in case ErrorFlg input message bit is set. */ 5003 #define UCM_REG_ERR_EVNT_ID 0xe00a4 5004 /* [RW 28] The CM erroneous header for QM and Timers formatting. */ 5005 #define UCM_REG_ERR_UCM_HDR 0xe00a0 5006 /* [RW 8] The Event ID for Timers expiration. */ 5007 #define UCM_REG_EXPR_EVNT_ID 0xe00a8 5008 /* [RW 8] FIC0 output initial credit. Max credit available - 255.Write 5009 writes the initial credit value; read returns the current value of the 5010 credit counter. Must be initialized to 64 at start-up. */ 5011 #define UCM_REG_FIC0_INIT_CRD 0xe020c 5012 /* [RW 8] FIC1 output initial credit. Max credit available - 255.Write 5013 writes the initial credit value; read returns the current value of the 5014 credit counter. Must be initialized to 64 at start-up. */ 5015 #define UCM_REG_FIC1_INIT_CRD 0xe0210 5016 /* [RW 1] Arbitration between Input Arbiter groups: 0 - fair Round-Robin; 1 5017 - strict priority defined by ~ucm_registers_gr_ag_pr.gr_ag_pr; 5018 ~ucm_registers_gr_ld0_pr.gr_ld0_pr and 5019 ~ucm_registers_gr_ld1_pr.gr_ld1_pr. */ 5020 #define UCM_REG_GR_ARB_TYPE 0xe0144 5021 /* [RW 2] Load (FIC0) channel group priority. The lowest priority is 0; the 5022 highest priority is 3. It is supposed that the Store channel group is 5023 compliment to the others. */ 5024 #define UCM_REG_GR_LD0_PR 0xe014c 5025 /* [RW 2] Load (FIC1) channel group priority. The lowest priority is 0; the 5026 highest priority is 3. It is supposed that the Store channel group is 5027 compliment to the others. */ 5028 #define UCM_REG_GR_LD1_PR 0xe0150 5029 /* [RW 2] The queue index for invalidate counter flag decision. */ 5030 #define UCM_REG_INV_CFLG_Q 0xe00e4 5031 /* [RW 5] The number of double REG-pairs; loaded from the STORM context and 5032 sent to STORM; for a specific connection type. the double REG-pairs are 5033 used in order to align to STORM context row size of 128 bits. The offset 5034 of these data in the STORM context is always 0. Index _i stands for the 5035 connection type (one of 16). */ 5036 #define UCM_REG_N_SM_CTX_LD_0 0xe0054 5037 #define UCM_REG_N_SM_CTX_LD_1 0xe0058 5038 #define UCM_REG_N_SM_CTX_LD_2 0xe005c 5039 #define UCM_REG_N_SM_CTX_LD_3 0xe0060 5040 #define UCM_REG_N_SM_CTX_LD_4 0xe0064 5041 #define UCM_REG_N_SM_CTX_LD_5 0xe0068 5042 #define UCM_REG_PHYS_QNUM0_0 0xe0110 5043 #define UCM_REG_PHYS_QNUM0_1 0xe0114 5044 #define UCM_REG_PHYS_QNUM1_0 0xe0118 5045 #define UCM_REG_PHYS_QNUM1_1 0xe011c 5046 #define UCM_REG_PHYS_QNUM2_0 0xe0120 5047 #define UCM_REG_PHYS_QNUM2_1 0xe0124 5048 #define UCM_REG_PHYS_QNUM3_0 0xe0128 5049 #define UCM_REG_PHYS_QNUM3_1 0xe012c 5050 /* [RW 8] The Event ID for Timers formatting in case of stop done. */ 5051 #define UCM_REG_STOP_EVNT_ID 0xe00ac 5052 /* [RC 1] Set when the message length mismatch (relative to last indication) 5053 at the STORM interface is detected. */ 5054 #define UCM_REG_STORM_LENGTH_MIS 0xe0154 5055 /* [RW 1] STORM - CM Interface enable. If 0 - the valid input is 5056 disregarded; acknowledge output is deasserted; all other signals are 5057 treated as usual; if 1 - normal activity. */ 5058 #define UCM_REG_STORM_UCM_IFEN 0xe0010 5059 /* [RW 3] The weight of the STORM input in the WRR mechanism. 0 stands for 5060 weight 8 (the most prioritised); 1 stands for weight 1(least 5061 prioritised); 2 stands for weight 2; tc. */ 5062 #define UCM_REG_STORM_WEIGHT 0xe00b0 5063 /* [RW 4] Timers output initial credit. Max credit available - 15.Write 5064 writes the initial credit value; read returns the current value of the 5065 credit counter. Must be initialized to 4 at start-up. */ 5066 #define UCM_REG_TM_INIT_CRD 0xe021c 5067 /* [RW 28] The CM header for Timers expiration command. */ 5068 #define UCM_REG_TM_UCM_HDR 0xe009c 5069 /* [RW 1] Timers - CM Interface enable. If 0 - the valid input is 5070 disregarded; acknowledge output is deasserted; all other signals are 5071 treated as usual; if 1 - normal activity. */ 5072 #define UCM_REG_TM_UCM_IFEN 0xe001c 5073 /* [RW 3] The weight of the Timers input in the WRR mechanism. 0 stands for 5074 weight 8 (the most prioritised); 1 stands for weight 1(least 5075 prioritised); 2 stands for weight 2; tc. */ 5076 #define UCM_REG_TM_WEIGHT 0xe00d4 5077 /* [RW 1] Input tsem Interface enable. If 0 - the valid input is 5078 disregarded; acknowledge output is deasserted; all other signals are 5079 treated as usual; if 1 - normal activity. */ 5080 #define UCM_REG_TSEM_IFEN 0xe0024 5081 /* [RC 1] Set when the message length mismatch (relative to last indication) 5082 at the tsem interface is detected. */ 5083 #define UCM_REG_TSEM_LENGTH_MIS 0xe015c 5084 /* [RW 3] The weight of the input tsem in the WRR mechanism. 0 stands for 5085 weight 8 (the most prioritised); 1 stands for weight 1(least 5086 prioritised); 2 stands for weight 2; tc. */ 5087 #define UCM_REG_TSEM_WEIGHT 0xe00b4 5088 /* [RW 1] CM - CFC Interface enable. If 0 - the valid input is disregarded; 5089 acknowledge output is deasserted; all other signals are treated as usual; 5090 if 1 - normal activity. */ 5091 #define UCM_REG_UCM_CFC_IFEN 0xe0044 5092 /* [RW 11] Interrupt mask register #0 read/write */ 5093 #define UCM_REG_UCM_INT_MASK 0xe01d4 5094 /* [R 11] Interrupt register #0 read */ 5095 #define UCM_REG_UCM_INT_STS 0xe01c8 5096 /* [RW 27] Parity mask register #0 read/write */ 5097 #define UCM_REG_UCM_PRTY_MASK 0xe01e4 5098 /* [R 27] Parity register #0 read */ 5099 #define UCM_REG_UCM_PRTY_STS 0xe01d8 5100 /* [RC 27] Parity register #0 read clear */ 5101 #define UCM_REG_UCM_PRTY_STS_CLR 0xe01dc 5102 /* [RW 2] The size of AG context region 0 in REG-pairs. Designates the MS 5103 REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5). 5104 Is used to determine the number of the AG context REG-pairs written back; 5105 when the Reg1WbFlg isn't set. */ 5106 #define UCM_REG_UCM_REG0_SZ 0xe00dc 5107 /* [RW 1] CM - STORM 0 Interface enable. If 0 - the acknowledge input is 5108 disregarded; valid is deasserted; all other signals are treated as usual; 5109 if 1 - normal activity. */ 5110 #define UCM_REG_UCM_STORM0_IFEN 0xe0004 5111 /* [RW 1] CM - STORM 1 Interface enable. If 0 - the acknowledge input is 5112 disregarded; valid is deasserted; all other signals are treated as usual; 5113 if 1 - normal activity. */ 5114 #define UCM_REG_UCM_STORM1_IFEN 0xe0008 5115 /* [RW 1] CM - Timers Interface enable. If 0 - the valid input is 5116 disregarded; acknowledge output is deasserted; all other signals are 5117 treated as usual; if 1 - normal activity. */ 5118 #define UCM_REG_UCM_TM_IFEN 0xe0020 5119 /* [RW 1] CM - QM Interface enable. If 0 - the acknowledge input is 5120 disregarded; valid is deasserted; all other signals are treated as usual; 5121 if 1 - normal activity. */ 5122 #define UCM_REG_UCM_UQM_IFEN 0xe000c 5123 /* [RW 1] If set the Q index; received from the QM is inserted to event ID. */ 5124 #define UCM_REG_UCM_UQM_USE_Q 0xe00d8 5125 /* [RW 6] QM output initial credit. Max credit available - 32.Write writes 5126 the initial credit value; read returns the current value of the credit 5127 counter. Must be initialized to 32 at start-up. */ 5128 #define UCM_REG_UQM_INIT_CRD 0xe0220 5129 /* [RW 3] The weight of the QM (primary) input in the WRR mechanism. 0 5130 stands for weight 8 (the most prioritised); 1 stands for weight 1(least 5131 prioritised); 2 stands for weight 2; tc. */ 5132 #define UCM_REG_UQM_P_WEIGHT 0xe00cc 5133 /* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0 5134 stands for weight 8 (the most prioritised); 1 stands for weight 1(least 5135 prioritised); 2 stands for weight 2; tc. */ 5136 #define UCM_REG_UQM_S_WEIGHT 0xe00d0 5137 /* [RW 28] The CM header value for QM request (primary). */ 5138 #define UCM_REG_UQM_UCM_HDR_P 0xe0094 5139 /* [RW 28] The CM header value for QM request (secondary). */ 5140 #define UCM_REG_UQM_UCM_HDR_S 0xe0098 5141 /* [RW 1] QM - CM Interface enable. If 0 - the valid input is disregarded; 5142 acknowledge output is deasserted; all other signals are treated as usual; 5143 if 1 - normal activity. */ 5144 #define UCM_REG_UQM_UCM_IFEN 0xe0014 5145 /* [RW 1] Input SDM Interface enable. If 0 - the valid input is disregarded; 5146 acknowledge output is deasserted; all other signals are treated as usual; 5147 if 1 - normal activity. */ 5148 #define UCM_REG_USDM_IFEN 0xe0018 5149 /* [RC 1] Set when the message length mismatch (relative to last indication) 5150 at the SDM interface is detected. */ 5151 #define UCM_REG_USDM_LENGTH_MIS 0xe0158 5152 /* [RW 3] The weight of the SDM input in the WRR mechanism. 0 stands for 5153 weight 8 (the most prioritised); 1 stands for weight 1(least 5154 prioritised); 2 stands for weight 2; tc. */ 5155 #define UCM_REG_USDM_WEIGHT 0xe00c8 5156 /* [RW 1] Input xsem Interface enable. If 0 - the valid input is 5157 disregarded; acknowledge output is deasserted; all other signals are 5158 treated as usual; if 1 - normal activity. */ 5159 #define UCM_REG_XSEM_IFEN 0xe002c 5160 /* [RC 1] Set when the message length mismatch (relative to last indication) 5161 at the xsem interface isdetected. */ 5162 #define UCM_REG_XSEM_LENGTH_MIS 0xe0164 5163 /* [RW 3] The weight of the input xsem in the WRR mechanism. 0 stands for 5164 weight 8 (the most prioritised); 1 stands for weight 1(least 5165 prioritised); 2 stands for weight 2; tc. */ 5166 #define UCM_REG_XSEM_WEIGHT 0xe00bc 5167 /* [RW 20] Indirect access to the descriptor table of the XX protection 5168 mechanism. The fields are:[5:0] - message length; 14:6] - message 5169 pointer; 19:15] - next pointer. */ 5170 #define UCM_REG_XX_DESCR_TABLE 0xe0280 5171 #define UCM_REG_XX_DESCR_TABLE_SIZE 27 5172 /* [R 6] Use to read the XX protection Free counter. */ 5173 #define UCM_REG_XX_FREE 0xe016c 5174 /* [RW 6] Initial value for the credit counter; responsible for fulfilling 5175 of the Input Stage XX protection buffer by the XX protection pending 5176 messages. Write writes the initial credit value; read returns the current 5177 value of the credit counter. Must be initialized to 12 at start-up. */ 5178 #define UCM_REG_XX_INIT_CRD 0xe0224 5179 /* [RW 6] The maximum number of pending messages; which may be stored in XX 5180 protection. ~ucm_registers_xx_free.xx_free read on read. */ 5181 #define UCM_REG_XX_MSG_NUM 0xe0228 5182 /* [RW 8] The Event ID; sent to the STORM in case of XX overflow. */ 5183 #define UCM_REG_XX_OVFL_EVNT_ID 0xe004c 5184 /* [RW 16] Indirect access to the XX table of the XX protection mechanism. 5185 The fields are: [4:0] - tail pointer; 10:5] - Link List size; 15:11] - 5186 header pointer. */ 5187 #define UCM_REG_XX_TABLE 0xe0300 5188 #define UMAC_COMMAND_CONFIG_REG_HD_ENA (0x1<<10) 5189 #define UMAC_COMMAND_CONFIG_REG_IGNORE_TX_PAUSE (0x1<<28) 5190 #define UMAC_COMMAND_CONFIG_REG_LOOP_ENA (0x1<<15) 5191 #define UMAC_COMMAND_CONFIG_REG_NO_LGTH_CHECK (0x1<<24) 5192 #define UMAC_COMMAND_CONFIG_REG_PAD_EN (0x1<<5) 5193 #define UMAC_COMMAND_CONFIG_REG_PAUSE_IGNORE (0x1<<8) 5194 #define UMAC_COMMAND_CONFIG_REG_PROMIS_EN (0x1<<4) 5195 #define UMAC_COMMAND_CONFIG_REG_RX_ENA (0x1<<1) 5196 #define UMAC_COMMAND_CONFIG_REG_SW_RESET (0x1<<13) 5197 #define UMAC_COMMAND_CONFIG_REG_TX_ENA (0x1<<0) 5198 #define UMAC_REG_COMMAND_CONFIG 0x8 5199 /* [RW 16] This is the duration for which MAC must wait to go back to ACTIVE 5200 * state from LPI state when it receives packet for transmission. The 5201 * decrement unit is 1 micro-second. */ 5202 #define UMAC_REG_EEE_WAKE_TIMER 0x6c 5203 /* [RW 32] Register Bit 0 refers to Bit 16 of the MAC address; Bit 1 refers 5204 * to bit 17 of the MAC address etc. */ 5205 #define UMAC_REG_MAC_ADDR0 0xc 5206 /* [RW 16] Register Bit 0 refers to Bit 0 of the MAC address; Register Bit 1 5207 * refers to Bit 1 of the MAC address etc. Bits 16 to 31 are reserved. */ 5208 #define UMAC_REG_MAC_ADDR1 0x10 5209 /* [RW 14] Defines a 14-Bit maximum frame length used by the MAC receive 5210 * logic to check frames. */ 5211 #define UMAC_REG_MAXFR 0x14 5212 #define UMAC_REG_UMAC_EEE_CTRL 0x64 5213 #define UMAC_UMAC_EEE_CTRL_REG_EEE_EN (0x1<<3) 5214 /* [RW 8] The event id for aggregated interrupt 0 */ 5215 #define USDM_REG_AGG_INT_EVENT_0 0xc4038 5216 #define USDM_REG_AGG_INT_EVENT_1 0xc403c 5217 #define USDM_REG_AGG_INT_EVENT_2 0xc4040 5218 #define USDM_REG_AGG_INT_EVENT_4 0xc4048 5219 #define USDM_REG_AGG_INT_EVENT_5 0xc404c 5220 #define USDM_REG_AGG_INT_EVENT_6 0xc4050 5221 /* [RW 1] For each aggregated interrupt index whether the mode is normal (0) 5222 or auto-mask-mode (1) */ 5223 #define USDM_REG_AGG_INT_MODE_0 0xc41b8 5224 #define USDM_REG_AGG_INT_MODE_1 0xc41bc 5225 #define USDM_REG_AGG_INT_MODE_4 0xc41c8 5226 #define USDM_REG_AGG_INT_MODE_5 0xc41cc 5227 #define USDM_REG_AGG_INT_MODE_6 0xc41d0 5228 /* [RW 1] The T bit for aggregated interrupt 5 */ 5229 #define USDM_REG_AGG_INT_T_5 0xc40cc 5230 #define USDM_REG_AGG_INT_T_6 0xc40d0 5231 /* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */ 5232 #define USDM_REG_CFC_RSP_START_ADDR 0xc4008 5233 /* [RW 16] The maximum value of the completion counter #0 */ 5234 #define USDM_REG_CMP_COUNTER_MAX0 0xc401c 5235 /* [RW 16] The maximum value of the completion counter #1 */ 5236 #define USDM_REG_CMP_COUNTER_MAX1 0xc4020 5237 /* [RW 16] The maximum value of the completion counter #2 */ 5238 #define USDM_REG_CMP_COUNTER_MAX2 0xc4024 5239 /* [RW 16] The maximum value of the completion counter #3 */ 5240 #define USDM_REG_CMP_COUNTER_MAX3 0xc4028 5241 /* [RW 13] The start address in the internal RAM for the completion 5242 counters. */ 5243 #define USDM_REG_CMP_COUNTER_START_ADDR 0xc400c 5244 #define USDM_REG_ENABLE_IN1 0xc4238 5245 #define USDM_REG_ENABLE_IN2 0xc423c 5246 #define USDM_REG_ENABLE_OUT1 0xc4240 5247 #define USDM_REG_ENABLE_OUT2 0xc4244 5248 /* [RW 4] The initial number of messages that can be sent to the pxp control 5249 interface without receiving any ACK. */ 5250 #define USDM_REG_INIT_CREDIT_PXP_CTRL 0xc44c0 5251 /* [ST 32] The number of ACK after placement messages received */ 5252 #define USDM_REG_NUM_OF_ACK_AFTER_PLACE 0xc4280 5253 /* [ST 32] The number of packet end messages received from the parser */ 5254 #define USDM_REG_NUM_OF_PKT_END_MSG 0xc4278 5255 /* [ST 32] The number of requests received from the pxp async if */ 5256 #define USDM_REG_NUM_OF_PXP_ASYNC_REQ 0xc427c 5257 /* [ST 32] The number of commands received in queue 0 */ 5258 #define USDM_REG_NUM_OF_Q0_CMD 0xc4248 5259 /* [ST 32] The number of commands received in queue 10 */ 5260 #define USDM_REG_NUM_OF_Q10_CMD 0xc4270 5261 /* [ST 32] The number of commands received in queue 11 */ 5262 #define USDM_REG_NUM_OF_Q11_CMD 0xc4274 5263 /* [ST 32] The number of commands received in queue 1 */ 5264 #define USDM_REG_NUM_OF_Q1_CMD 0xc424c 5265 /* [ST 32] The number of commands received in queue 2 */ 5266 #define USDM_REG_NUM_OF_Q2_CMD 0xc4250 5267 /* [ST 32] The number of commands received in queue 3 */ 5268 #define USDM_REG_NUM_OF_Q3_CMD 0xc4254 5269 /* [ST 32] The number of commands received in queue 4 */ 5270 #define USDM_REG_NUM_OF_Q4_CMD 0xc4258 5271 /* [ST 32] The number of commands received in queue 5 */ 5272 #define USDM_REG_NUM_OF_Q5_CMD 0xc425c 5273 /* [ST 32] The number of commands received in queue 6 */ 5274 #define USDM_REG_NUM_OF_Q6_CMD 0xc4260 5275 /* [ST 32] The number of commands received in queue 7 */ 5276 #define USDM_REG_NUM_OF_Q7_CMD 0xc4264 5277 /* [ST 32] The number of commands received in queue 8 */ 5278 #define USDM_REG_NUM_OF_Q8_CMD 0xc4268 5279 /* [ST 32] The number of commands received in queue 9 */ 5280 #define USDM_REG_NUM_OF_Q9_CMD 0xc426c 5281 /* [RW 13] The start address in the internal RAM for the packet end message */ 5282 #define USDM_REG_PCK_END_MSG_START_ADDR 0xc4014 5283 /* [RW 13] The start address in the internal RAM for queue counters */ 5284 #define USDM_REG_Q_COUNTER_START_ADDR 0xc4010 5285 /* [R 1] pxp_ctrl rd_data fifo empty in sdm_dma_rsp block */ 5286 #define USDM_REG_RSP_PXP_CTRL_RDATA_EMPTY 0xc4550 5287 /* [R 1] parser fifo empty in sdm_sync block */ 5288 #define USDM_REG_SYNC_PARSER_EMPTY 0xc4558 5289 /* [R 1] parser serial fifo empty in sdm_sync block */ 5290 #define USDM_REG_SYNC_SYNC_EMPTY 0xc4560 5291 /* [RW 32] Tick for timer counter. Applicable only when 5292 ~usdm_registers_timer_tick_enable.timer_tick_enable =1 */ 5293 #define USDM_REG_TIMER_TICK 0xc4000 5294 /* [RW 32] Interrupt mask register #0 read/write */ 5295 #define USDM_REG_USDM_INT_MASK_0 0xc42a0 5296 #define USDM_REG_USDM_INT_MASK_1 0xc42b0 5297 /* [R 32] Interrupt register #0 read */ 5298 #define USDM_REG_USDM_INT_STS_0 0xc4294 5299 #define USDM_REG_USDM_INT_STS_1 0xc42a4 5300 /* [RW 11] Parity mask register #0 read/write */ 5301 #define USDM_REG_USDM_PRTY_MASK 0xc42c0 5302 /* [R 11] Parity register #0 read */ 5303 #define USDM_REG_USDM_PRTY_STS 0xc42b4 5304 /* [RC 11] Parity register #0 read clear */ 5305 #define USDM_REG_USDM_PRTY_STS_CLR 0xc42b8 5306 /* [RW 5] The number of time_slots in the arbitration cycle */ 5307 #define USEM_REG_ARB_CYCLE_SIZE 0x300034 5308 /* [RW 3] The source that is associated with arbitration element 0. Source 5309 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 5310 sleeping thread with priority 1; 4- sleeping thread with priority 2 */ 5311 #define USEM_REG_ARB_ELEMENT0 0x300020 5312 /* [RW 3] The source that is associated with arbitration element 1. Source 5313 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 5314 sleeping thread with priority 1; 4- sleeping thread with priority 2. 5315 Could not be equal to register ~usem_registers_arb_element0.arb_element0 */ 5316 #define USEM_REG_ARB_ELEMENT1 0x300024 5317 /* [RW 3] The source that is associated with arbitration element 2. Source 5318 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 5319 sleeping thread with priority 1; 4- sleeping thread with priority 2. 5320 Could not be equal to register ~usem_registers_arb_element0.arb_element0 5321 and ~usem_registers_arb_element1.arb_element1 */ 5322 #define USEM_REG_ARB_ELEMENT2 0x300028 5323 /* [RW 3] The source that is associated with arbitration element 3. Source 5324 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 5325 sleeping thread with priority 1; 4- sleeping thread with priority 2.Could 5326 not be equal to register ~usem_registers_arb_element0.arb_element0 and 5327 ~usem_registers_arb_element1.arb_element1 and 5328 ~usem_registers_arb_element2.arb_element2 */ 5329 #define USEM_REG_ARB_ELEMENT3 0x30002c 5330 /* [RW 3] The source that is associated with arbitration element 4. Source 5331 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 5332 sleeping thread with priority 1; 4- sleeping thread with priority 2. 5333 Could not be equal to register ~usem_registers_arb_element0.arb_element0 5334 and ~usem_registers_arb_element1.arb_element1 and 5335 ~usem_registers_arb_element2.arb_element2 and 5336 ~usem_registers_arb_element3.arb_element3 */ 5337 #define USEM_REG_ARB_ELEMENT4 0x300030 5338 #define USEM_REG_ENABLE_IN 0x3000a4 5339 #define USEM_REG_ENABLE_OUT 0x3000a8 5340 /* [RW 32] This address space contains all registers and memories that are 5341 placed in SEM_FAST block. The SEM_FAST registers are described in 5342 appendix B. In order to access the sem_fast registers the base address 5343 ~fast_memory.fast_memory should be added to eachsem_fast register offset. */ 5344 #define USEM_REG_FAST_MEMORY 0x320000 5345 /* [RW 1] Disables input messages from FIC0 May be updated during run_time 5346 by the microcode */ 5347 #define USEM_REG_FIC0_DISABLE 0x300224 5348 /* [RW 1] Disables input messages from FIC1 May be updated during run_time 5349 by the microcode */ 5350 #define USEM_REG_FIC1_DISABLE 0x300234 5351 /* [RW 15] Interrupt table Read and write access to it is not possible in 5352 the middle of the work */ 5353 #define USEM_REG_INT_TABLE 0x300400 5354 /* [ST 24] Statistics register. The number of messages that entered through 5355 FIC0 */ 5356 #define USEM_REG_MSG_NUM_FIC0 0x300000 5357 /* [ST 24] Statistics register. The number of messages that entered through 5358 FIC1 */ 5359 #define USEM_REG_MSG_NUM_FIC1 0x300004 5360 /* [ST 24] Statistics register. The number of messages that were sent to 5361 FOC0 */ 5362 #define USEM_REG_MSG_NUM_FOC0 0x300008 5363 /* [ST 24] Statistics register. The number of messages that were sent to 5364 FOC1 */ 5365 #define USEM_REG_MSG_NUM_FOC1 0x30000c 5366 /* [ST 24] Statistics register. The number of messages that were sent to 5367 FOC2 */ 5368 #define USEM_REG_MSG_NUM_FOC2 0x300010 5369 /* [ST 24] Statistics register. The number of messages that were sent to 5370 FOC3 */ 5371 #define USEM_REG_MSG_NUM_FOC3 0x300014 5372 /* [RW 1] Disables input messages from the passive buffer May be updated 5373 during run_time by the microcode */ 5374 #define USEM_REG_PAS_DISABLE 0x30024c 5375 /* [WB 128] Debug only. Passive buffer memory */ 5376 #define USEM_REG_PASSIVE_BUFFER 0x302000 5377 /* [WB 46] pram memory. B45 is parity; b[44:0] - data. */ 5378 #define USEM_REG_PRAM 0x340000 5379 /* [R 16] Valid sleeping threads indication have bit per thread */ 5380 #define USEM_REG_SLEEP_THREADS_VALID 0x30026c 5381 /* [R 1] EXT_STORE FIFO is empty in sem_slow_ls_ext */ 5382 #define USEM_REG_SLOW_EXT_STORE_EMPTY 0x3002a0 5383 /* [RW 16] List of free threads . There is a bit per thread. */ 5384 #define USEM_REG_THREADS_LIST 0x3002e4 5385 /* [RW 3] The arbitration scheme of time_slot 0 */ 5386 #define USEM_REG_TS_0_AS 0x300038 5387 /* [RW 3] The arbitration scheme of time_slot 10 */ 5388 #define USEM_REG_TS_10_AS 0x300060 5389 /* [RW 3] The arbitration scheme of time_slot 11 */ 5390 #define USEM_REG_TS_11_AS 0x300064 5391 /* [RW 3] The arbitration scheme of time_slot 12 */ 5392 #define USEM_REG_TS_12_AS 0x300068 5393 /* [RW 3] The arbitration scheme of time_slot 13 */ 5394 #define USEM_REG_TS_13_AS 0x30006c 5395 /* [RW 3] The arbitration scheme of time_slot 14 */ 5396 #define USEM_REG_TS_14_AS 0x300070 5397 /* [RW 3] The arbitration scheme of time_slot 15 */ 5398 #define USEM_REG_TS_15_AS 0x300074 5399 /* [RW 3] The arbitration scheme of time_slot 16 */ 5400 #define USEM_REG_TS_16_AS 0x300078 5401 /* [RW 3] The arbitration scheme of time_slot 17 */ 5402 #define USEM_REG_TS_17_AS 0x30007c 5403 /* [RW 3] The arbitration scheme of time_slot 18 */ 5404 #define USEM_REG_TS_18_AS 0x300080 5405 /* [RW 3] The arbitration scheme of time_slot 1 */ 5406 #define USEM_REG_TS_1_AS 0x30003c 5407 /* [RW 3] The arbitration scheme of time_slot 2 */ 5408 #define USEM_REG_TS_2_AS 0x300040 5409 /* [RW 3] The arbitration scheme of time_slot 3 */ 5410 #define USEM_REG_TS_3_AS 0x300044 5411 /* [RW 3] The arbitration scheme of time_slot 4 */ 5412 #define USEM_REG_TS_4_AS 0x300048 5413 /* [RW 3] The arbitration scheme of time_slot 5 */ 5414 #define USEM_REG_TS_5_AS 0x30004c 5415 /* [RW 3] The arbitration scheme of time_slot 6 */ 5416 #define USEM_REG_TS_6_AS 0x300050 5417 /* [RW 3] The arbitration scheme of time_slot 7 */ 5418 #define USEM_REG_TS_7_AS 0x300054 5419 /* [RW 3] The arbitration scheme of time_slot 8 */ 5420 #define USEM_REG_TS_8_AS 0x300058 5421 /* [RW 3] The arbitration scheme of time_slot 9 */ 5422 #define USEM_REG_TS_9_AS 0x30005c 5423 /* [RW 32] Interrupt mask register #0 read/write */ 5424 #define USEM_REG_USEM_INT_MASK_0 0x300110 5425 #define USEM_REG_USEM_INT_MASK_1 0x300120 5426 /* [R 32] Interrupt register #0 read */ 5427 #define USEM_REG_USEM_INT_STS_0 0x300104 5428 #define USEM_REG_USEM_INT_STS_1 0x300114 5429 /* [RW 32] Parity mask register #0 read/write */ 5430 #define USEM_REG_USEM_PRTY_MASK_0 0x300130 5431 #define USEM_REG_USEM_PRTY_MASK_1 0x300140 5432 /* [R 32] Parity register #0 read */ 5433 #define USEM_REG_USEM_PRTY_STS_0 0x300124 5434 #define USEM_REG_USEM_PRTY_STS_1 0x300134 5435 /* [RC 32] Parity register #0 read clear */ 5436 #define USEM_REG_USEM_PRTY_STS_CLR_0 0x300128 5437 #define USEM_REG_USEM_PRTY_STS_CLR_1 0x300138 5438 /* [W 7] VF or PF ID for reset error bit. Values 0-63 reset error bit for 64 5439 * VF; values 64-67 reset error for 4 PF; values 68-127 are not valid. */ 5440 #define USEM_REG_VFPF_ERR_NUM 0x300380 5441 #define VFC_MEMORIES_RST_REG_CAM_RST (0x1<<0) 5442 #define VFC_MEMORIES_RST_REG_RAM_RST (0x1<<1) 5443 #define VFC_REG_MEMORIES_RST 0x1943c 5444 /* [RW 32] Indirect access to AG context with 32-bits granularity. The bits 5445 * [12:8] of the address should be the offset within the accessed LCID 5446 * context; the bits [7:0] are the accessed LCID.Example: to write to REG10 5447 * LCID100. The RBC address should be 13'ha64. */ 5448 #define XCM_REG_AG_CTX 0x28000 5449 /* [RW 2] The queue index for registration on Aux1 counter flag. */ 5450 #define XCM_REG_AUX1_Q 0x20134 5451 /* [RW 2] Per each decision rule the queue index to register to. */ 5452 #define XCM_REG_AUX_CNT_FLG_Q_19 0x201b0 5453 /* [R 5] Used to read the XX protection CAM occupancy counter. */ 5454 #define XCM_REG_CAM_OCCUP 0x20244 5455 /* [RW 1] CDU AG read Interface enable. If 0 - the request input is 5456 disregarded; valid output is deasserted; all other signals are treated as 5457 usual; if 1 - normal activity. */ 5458 #define XCM_REG_CDU_AG_RD_IFEN 0x20044 5459 /* [RW 1] CDU AG write Interface enable. If 0 - the request and valid input 5460 are disregarded; all other signals are treated as usual; if 1 - normal 5461 activity. */ 5462 #define XCM_REG_CDU_AG_WR_IFEN 0x20040 5463 /* [RW 1] CDU STORM read Interface enable. If 0 - the request input is 5464 disregarded; valid output is deasserted; all other signals are treated as 5465 usual; if 1 - normal activity. */ 5466 #define XCM_REG_CDU_SM_RD_IFEN 0x2004c 5467 /* [RW 1] CDU STORM write Interface enable. If 0 - the request and valid 5468 input is disregarded; all other signals are treated as usual; if 1 - 5469 normal activity. */ 5470 #define XCM_REG_CDU_SM_WR_IFEN 0x20048 5471 /* [RW 4] CFC output initial credit. Max credit available - 15.Write writes 5472 the initial credit value; read returns the current value of the credit 5473 counter. Must be initialized to 1 at start-up. */ 5474 #define XCM_REG_CFC_INIT_CRD 0x20404 5475 /* [RW 3] The weight of the CP input in the WRR mechanism. 0 stands for 5476 weight 8 (the most prioritised); 1 stands for weight 1(least 5477 prioritised); 2 stands for weight 2; tc. */ 5478 #define XCM_REG_CP_WEIGHT 0x200dc 5479 /* [RW 1] Input csem Interface enable. If 0 - the valid input is 5480 disregarded; acknowledge output is deasserted; all other signals are 5481 treated as usual; if 1 - normal activity. */ 5482 #define XCM_REG_CSEM_IFEN 0x20028 5483 /* [RC 1] Set at message length mismatch (relative to last indication) at 5484 the csem interface. */ 5485 #define XCM_REG_CSEM_LENGTH_MIS 0x20228 5486 /* [RW 3] The weight of the input csem in the WRR mechanism. 0 stands for 5487 weight 8 (the most prioritised); 1 stands for weight 1(least 5488 prioritised); 2 stands for weight 2; tc. */ 5489 #define XCM_REG_CSEM_WEIGHT 0x200c4 5490 /* [RW 1] Input dorq Interface enable. If 0 - the valid input is 5491 disregarded; acknowledge output is deasserted; all other signals are 5492 treated as usual; if 1 - normal activity. */ 5493 #define XCM_REG_DORQ_IFEN 0x20030 5494 /* [RC 1] Set at message length mismatch (relative to last indication) at 5495 the dorq interface. */ 5496 #define XCM_REG_DORQ_LENGTH_MIS 0x20230 5497 /* [RW 3] The weight of the input dorq in the WRR mechanism. 0 stands for 5498 weight 8 (the most prioritised); 1 stands for weight 1(least 5499 prioritised); 2 stands for weight 2; tc. */ 5500 #define XCM_REG_DORQ_WEIGHT 0x200cc 5501 /* [RW 8] The Event ID in case the ErrorFlg input message bit is set. */ 5502 #define XCM_REG_ERR_EVNT_ID 0x200b0 5503 /* [RW 28] The CM erroneous header for QM and Timers formatting. */ 5504 #define XCM_REG_ERR_XCM_HDR 0x200ac 5505 /* [RW 8] The Event ID for Timers expiration. */ 5506 #define XCM_REG_EXPR_EVNT_ID 0x200b4 5507 /* [RW 8] FIC0 output initial credit. Max credit available - 255.Write 5508 writes the initial credit value; read returns the current value of the 5509 credit counter. Must be initialized to 64 at start-up. */ 5510 #define XCM_REG_FIC0_INIT_CRD 0x2040c 5511 /* [RW 8] FIC1 output initial credit. Max credit available - 255.Write 5512 writes the initial credit value; read returns the current value of the 5513 credit counter. Must be initialized to 64 at start-up. */ 5514 #define XCM_REG_FIC1_INIT_CRD 0x20410 5515 #define XCM_REG_GLB_DEL_ACK_MAX_CNT_0 0x20118 5516 #define XCM_REG_GLB_DEL_ACK_MAX_CNT_1 0x2011c 5517 #define XCM_REG_GLB_DEL_ACK_TMR_VAL_0 0x20108 5518 #define XCM_REG_GLB_DEL_ACK_TMR_VAL_1 0x2010c 5519 /* [RW 1] Arbitratiojn between Input Arbiter groups: 0 - fair Round-Robin; 1 5520 - strict priority defined by ~xcm_registers_gr_ag_pr.gr_ag_pr; 5521 ~xcm_registers_gr_ld0_pr.gr_ld0_pr and 5522 ~xcm_registers_gr_ld1_pr.gr_ld1_pr. */ 5523 #define XCM_REG_GR_ARB_TYPE 0x2020c 5524 /* [RW 2] Load (FIC0) channel group priority. The lowest priority is 0; the 5525 highest priority is 3. It is supposed that the Channel group is the 5526 compliment of the other 3 groups. */ 5527 #define XCM_REG_GR_LD0_PR 0x20214 5528 /* [RW 2] Load (FIC1) channel group priority. The lowest priority is 0; the 5529 highest priority is 3. It is supposed that the Channel group is the 5530 compliment of the other 3 groups. */ 5531 #define XCM_REG_GR_LD1_PR 0x20218 5532 /* [RW 1] Input nig0 Interface enable. If 0 - the valid input is 5533 disregarded; acknowledge output is deasserted; all other signals are 5534 treated as usual; if 1 - normal activity. */ 5535 #define XCM_REG_NIG0_IFEN 0x20038 5536 /* [RC 1] Set at message length mismatch (relative to last indication) at 5537 the nig0 interface. */ 5538 #define XCM_REG_NIG0_LENGTH_MIS 0x20238 5539 /* [RW 3] The weight of the input nig0 in the WRR mechanism. 0 stands for 5540 weight 8 (the most prioritised); 1 stands for weight 1(least 5541 prioritised); 2 stands for weight 2; tc. */ 5542 #define XCM_REG_NIG0_WEIGHT 0x200d4 5543 /* [RW 1] Input nig1 Interface enable. If 0 - the valid input is 5544 disregarded; acknowledge output is deasserted; all other signals are 5545 treated as usual; if 1 - normal activity. */ 5546 #define XCM_REG_NIG1_IFEN 0x2003c 5547 /* [RC 1] Set at message length mismatch (relative to last indication) at 5548 the nig1 interface. */ 5549 #define XCM_REG_NIG1_LENGTH_MIS 0x2023c 5550 /* [RW 5] The number of double REG-pairs; loaded from the STORM context and 5551 sent to STORM; for a specific connection type. The double REG-pairs are 5552 used in order to align to STORM context row size of 128 bits. The offset 5553 of these data in the STORM context is always 0. Index _i stands for the 5554 connection type (one of 16). */ 5555 #define XCM_REG_N_SM_CTX_LD_0 0x20060 5556 #define XCM_REG_N_SM_CTX_LD_1 0x20064 5557 #define XCM_REG_N_SM_CTX_LD_2 0x20068 5558 #define XCM_REG_N_SM_CTX_LD_3 0x2006c 5559 #define XCM_REG_N_SM_CTX_LD_4 0x20070 5560 #define XCM_REG_N_SM_CTX_LD_5 0x20074 5561 /* [RW 1] Input pbf Interface enable. If 0 - the valid input is disregarded; 5562 acknowledge output is deasserted; all other signals are treated as usual; 5563 if 1 - normal activity. */ 5564 #define XCM_REG_PBF_IFEN 0x20034 5565 /* [RC 1] Set at message length mismatch (relative to last indication) at 5566 the pbf interface. */ 5567 #define XCM_REG_PBF_LENGTH_MIS 0x20234 5568 /* [RW 3] The weight of the input pbf in the WRR mechanism. 0 stands for 5569 weight 8 (the most prioritised); 1 stands for weight 1(least 5570 prioritised); 2 stands for weight 2; tc. */ 5571 #define XCM_REG_PBF_WEIGHT 0x200d0 5572 #define XCM_REG_PHYS_QNUM3_0 0x20100 5573 #define XCM_REG_PHYS_QNUM3_1 0x20104 5574 /* [RW 8] The Event ID for Timers formatting in case of stop done. */ 5575 #define XCM_REG_STOP_EVNT_ID 0x200b8 5576 /* [RC 1] Set at message length mismatch (relative to last indication) at 5577 the STORM interface. */ 5578 #define XCM_REG_STORM_LENGTH_MIS 0x2021c 5579 /* [RW 3] The weight of the STORM input in the WRR mechanism. 0 stands for 5580 weight 8 (the most prioritised); 1 stands for weight 1(least 5581 prioritised); 2 stands for weight 2; tc. */ 5582 #define XCM_REG_STORM_WEIGHT 0x200bc 5583 /* [RW 1] STORM - CM Interface enable. If 0 - the valid input is 5584 disregarded; acknowledge output is deasserted; all other signals are 5585 treated as usual; if 1 - normal activity. */ 5586 #define XCM_REG_STORM_XCM_IFEN 0x20010 5587 /* [RW 4] Timers output initial credit. Max credit available - 15.Write 5588 writes the initial credit value; read returns the current value of the 5589 credit counter. Must be initialized to 4 at start-up. */ 5590 #define XCM_REG_TM_INIT_CRD 0x2041c 5591 /* [RW 3] The weight of the Timers input in the WRR mechanism. 0 stands for 5592 weight 8 (the most prioritised); 1 stands for weight 1(least 5593 prioritised); 2 stands for weight 2; tc. */ 5594 #define XCM_REG_TM_WEIGHT 0x200ec 5595 /* [RW 28] The CM header for Timers expiration command. */ 5596 #define XCM_REG_TM_XCM_HDR 0x200a8 5597 /* [RW 1] Timers - CM Interface enable. If 0 - the valid input is 5598 disregarded; acknowledge output is deasserted; all other signals are 5599 treated as usual; if 1 - normal activity. */ 5600 #define XCM_REG_TM_XCM_IFEN 0x2001c 5601 /* [RW 1] Input tsem Interface enable. If 0 - the valid input is 5602 disregarded; acknowledge output is deasserted; all other signals are 5603 treated as usual; if 1 - normal activity. */ 5604 #define XCM_REG_TSEM_IFEN 0x20024 5605 /* [RC 1] Set at message length mismatch (relative to last indication) at 5606 the tsem interface. */ 5607 #define XCM_REG_TSEM_LENGTH_MIS 0x20224 5608 /* [RW 3] The weight of the input tsem in the WRR mechanism. 0 stands for 5609 weight 8 (the most prioritised); 1 stands for weight 1(least 5610 prioritised); 2 stands for weight 2; tc. */ 5611 #define XCM_REG_TSEM_WEIGHT 0x200c0 5612 /* [RW 2] The queue index for registration on UNA greater NXT decision rule. */ 5613 #define XCM_REG_UNA_GT_NXT_Q 0x20120 5614 /* [RW 1] Input usem Interface enable. If 0 - the valid input is 5615 disregarded; acknowledge output is deasserted; all other signals are 5616 treated as usual; if 1 - normal activity. */ 5617 #define XCM_REG_USEM_IFEN 0x2002c 5618 /* [RC 1] Message length mismatch (relative to last indication) at the usem 5619 interface. */ 5620 #define XCM_REG_USEM_LENGTH_MIS 0x2022c 5621 /* [RW 3] The weight of the input usem in the WRR mechanism. 0 stands for 5622 weight 8 (the most prioritised); 1 stands for weight 1(least 5623 prioritised); 2 stands for weight 2; tc. */ 5624 #define XCM_REG_USEM_WEIGHT 0x200c8 5625 #define XCM_REG_WU_DA_CNT_CMD00 0x201d4 5626 #define XCM_REG_WU_DA_CNT_CMD01 0x201d8 5627 #define XCM_REG_WU_DA_CNT_CMD10 0x201dc 5628 #define XCM_REG_WU_DA_CNT_CMD11 0x201e0 5629 #define XCM_REG_WU_DA_CNT_UPD_VAL00 0x201e4 5630 #define XCM_REG_WU_DA_CNT_UPD_VAL01 0x201e8 5631 #define XCM_REG_WU_DA_CNT_UPD_VAL10 0x201ec 5632 #define XCM_REG_WU_DA_CNT_UPD_VAL11 0x201f0 5633 #define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00 0x201c4 5634 #define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01 0x201c8 5635 #define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD10 0x201cc 5636 #define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD11 0x201d0 5637 /* [RW 1] CM - CFC Interface enable. If 0 - the valid input is disregarded; 5638 acknowledge output is deasserted; all other signals are treated as usual; 5639 if 1 - normal activity. */ 5640 #define XCM_REG_XCM_CFC_IFEN 0x20050 5641 /* [RW 14] Interrupt mask register #0 read/write */ 5642 #define XCM_REG_XCM_INT_MASK 0x202b4 5643 /* [R 14] Interrupt register #0 read */ 5644 #define XCM_REG_XCM_INT_STS 0x202a8 5645 /* [RW 30] Parity mask register #0 read/write */ 5646 #define XCM_REG_XCM_PRTY_MASK 0x202c4 5647 /* [R 30] Parity register #0 read */ 5648 #define XCM_REG_XCM_PRTY_STS 0x202b8 5649 /* [RC 30] Parity register #0 read clear */ 5650 #define XCM_REG_XCM_PRTY_STS_CLR 0x202bc 5651 5652 /* [RW 4] The size of AG context region 0 in REG-pairs. Designates the MS 5653 REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5). 5654 Is used to determine the number of the AG context REG-pairs written back; 5655 when the Reg1WbFlg isn't set. */ 5656 #define XCM_REG_XCM_REG0_SZ 0x200f4 5657 /* [RW 1] CM - STORM 0 Interface enable. If 0 - the acknowledge input is 5658 disregarded; valid is deasserted; all other signals are treated as usual; 5659 if 1 - normal activity. */ 5660 #define XCM_REG_XCM_STORM0_IFEN 0x20004 5661 /* [RW 1] CM - STORM 1 Interface enable. If 0 - the acknowledge input is 5662 disregarded; valid is deasserted; all other signals are treated as usual; 5663 if 1 - normal activity. */ 5664 #define XCM_REG_XCM_STORM1_IFEN 0x20008 5665 /* [RW 1] CM - Timers Interface enable. If 0 - the valid input is 5666 disregarded; acknowledge output is deasserted; all other signals are 5667 treated as usual; if 1 - normal activity. */ 5668 #define XCM_REG_XCM_TM_IFEN 0x20020 5669 /* [RW 1] CM - QM Interface enable. If 0 - the acknowledge input is 5670 disregarded; valid is deasserted; all other signals are treated as usual; 5671 if 1 - normal activity. */ 5672 #define XCM_REG_XCM_XQM_IFEN 0x2000c 5673 /* [RW 1] If set the Q index; received from the QM is inserted to event ID. */ 5674 #define XCM_REG_XCM_XQM_USE_Q 0x200f0 5675 /* [RW 4] The value by which CFC updates the activity counter at QM bypass. */ 5676 #define XCM_REG_XQM_BYP_ACT_UPD 0x200fc 5677 /* [RW 6] QM output initial credit. Max credit available - 32.Write writes 5678 the initial credit value; read returns the current value of the credit 5679 counter. Must be initialized to 32 at start-up. */ 5680 #define XCM_REG_XQM_INIT_CRD 0x20420 5681 /* [RW 3] The weight of the QM (primary) input in the WRR mechanism. 0 5682 stands for weight 8 (the most prioritised); 1 stands for weight 1(least 5683 prioritised); 2 stands for weight 2; tc. */ 5684 #define XCM_REG_XQM_P_WEIGHT 0x200e4 5685 /* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0 5686 stands for weight 8 (the most prioritised); 1 stands for weight 1(least 5687 prioritised); 2 stands for weight 2; tc. */ 5688 #define XCM_REG_XQM_S_WEIGHT 0x200e8 5689 /* [RW 28] The CM header value for QM request (primary). */ 5690 #define XCM_REG_XQM_XCM_HDR_P 0x200a0 5691 /* [RW 28] The CM header value for QM request (secondary). */ 5692 #define XCM_REG_XQM_XCM_HDR_S 0x200a4 5693 /* [RW 1] QM - CM Interface enable. If 0 - the valid input is disregarded; 5694 acknowledge output is deasserted; all other signals are treated as usual; 5695 if 1 - normal activity. */ 5696 #define XCM_REG_XQM_XCM_IFEN 0x20014 5697 /* [RW 1] Input SDM Interface enable. If 0 - the valid input is disregarded; 5698 acknowledge output is deasserted; all other signals are treated as usual; 5699 if 1 - normal activity. */ 5700 #define XCM_REG_XSDM_IFEN 0x20018 5701 /* [RC 1] Set at message length mismatch (relative to last indication) at 5702 the SDM interface. */ 5703 #define XCM_REG_XSDM_LENGTH_MIS 0x20220 5704 /* [RW 3] The weight of the SDM input in the WRR mechanism. 0 stands for 5705 weight 8 (the most prioritised); 1 stands for weight 1(least 5706 prioritised); 2 stands for weight 2; tc. */ 5707 #define XCM_REG_XSDM_WEIGHT 0x200e0 5708 /* [RW 17] Indirect access to the descriptor table of the XX protection 5709 mechanism. The fields are: [5:0] - message length; 11:6] - message 5710 pointer; 16:12] - next pointer. */ 5711 #define XCM_REG_XX_DESCR_TABLE 0x20480 5712 #define XCM_REG_XX_DESCR_TABLE_SIZE 32 5713 /* [R 6] Used to read the XX protection Free counter. */ 5714 #define XCM_REG_XX_FREE 0x20240 5715 /* [RW 6] Initial value for the credit counter; responsible for fulfilling 5716 of the Input Stage XX protection buffer by the XX protection pending 5717 messages. Max credit available - 3.Write writes the initial credit value; 5718 read returns the current value of the credit counter. Must be initialized 5719 to 2 at start-up. */ 5720 #define XCM_REG_XX_INIT_CRD 0x20424 5721 /* [RW 6] The maximum number of pending messages; which may be stored in XX 5722 protection. ~xcm_registers_xx_free.xx_free read on read. */ 5723 #define XCM_REG_XX_MSG_NUM 0x20428 5724 /* [RW 8] The Event ID; sent to the STORM in case of XX overflow. */ 5725 #define XCM_REG_XX_OVFL_EVNT_ID 0x20058 5726 #define XMAC_CLEAR_RX_LSS_STATUS_REG_CLEAR_LOCAL_FAULT_STATUS (0x1<<0) 5727 #define XMAC_CLEAR_RX_LSS_STATUS_REG_CLEAR_REMOTE_FAULT_STATUS (0x1<<1) 5728 #define XMAC_CTRL_REG_LINE_LOCAL_LPBK (0x1<<2) 5729 #define XMAC_CTRL_REG_RX_EN (0x1<<1) 5730 #define XMAC_CTRL_REG_SOFT_RESET (0x1<<6) 5731 #define XMAC_CTRL_REG_TX_EN (0x1<<0) 5732 #define XMAC_CTRL_REG_XLGMII_ALIGN_ENB (0x1<<7) 5733 #define XMAC_PAUSE_CTRL_REG_RX_PAUSE_EN (0x1<<18) 5734 #define XMAC_PAUSE_CTRL_REG_TX_PAUSE_EN (0x1<<17) 5735 #define XMAC_PFC_CTRL_HI_REG_FORCE_PFC_XON (0x1<<1) 5736 #define XMAC_PFC_CTRL_HI_REG_PFC_REFRESH_EN (0x1<<0) 5737 #define XMAC_PFC_CTRL_HI_REG_PFC_STATS_EN (0x1<<3) 5738 #define XMAC_PFC_CTRL_HI_REG_RX_PFC_EN (0x1<<4) 5739 #define XMAC_PFC_CTRL_HI_REG_TX_PFC_EN (0x1<<5) 5740 #define XMAC_REG_CLEAR_RX_LSS_STATUS 0x60 5741 #define XMAC_REG_CTRL 0 5742 /* [RW 16] Upper 48 bits of ctrl_sa register. Used as the SA in PAUSE/PFC 5743 * packets transmitted by the MAC */ 5744 #define XMAC_REG_CTRL_SA_HI 0x2c 5745 /* [RW 32] Lower 48 bits of ctrl_sa register. Used as the SA in PAUSE/PFC 5746 * packets transmitted by the MAC */ 5747 #define XMAC_REG_CTRL_SA_LO 0x28 5748 #define XMAC_REG_EEE_CTRL 0xd8 5749 #define XMAC_REG_EEE_TIMERS_HI 0xe4 5750 #define XMAC_REG_PAUSE_CTRL 0x68 5751 #define XMAC_REG_PFC_CTRL 0x70 5752 #define XMAC_REG_PFC_CTRL_HI 0x74 5753 #define XMAC_REG_RX_LSS_CTRL 0x50 5754 #define XMAC_REG_RX_LSS_STATUS 0x58 5755 /* [RW 14] Maximum packet size in receive direction; exclusive of preamble & 5756 * CRC in strip mode */ 5757 #define XMAC_REG_RX_MAX_SIZE 0x40 5758 #define XMAC_REG_TX_CTRL 0x20 5759 #define XMAC_RX_LSS_CTRL_REG_LOCAL_FAULT_DISABLE (0x1<<0) 5760 #define XMAC_RX_LSS_CTRL_REG_REMOTE_FAULT_DISABLE (0x1<<1) 5761 /* [RW 16] Indirect access to the XX table of the XX protection mechanism. 5762 The fields are:[4:0] - tail pointer; 9:5] - Link List size; 14:10] - 5763 header pointer. */ 5764 #define XCM_REG_XX_TABLE 0x20500 5765 /* [RW 8] The event id for aggregated interrupt 0 */ 5766 #define XSDM_REG_AGG_INT_EVENT_0 0x166038 5767 #define XSDM_REG_AGG_INT_EVENT_1 0x16603c 5768 #define XSDM_REG_AGG_INT_EVENT_10 0x166060 5769 #define XSDM_REG_AGG_INT_EVENT_11 0x166064 5770 #define XSDM_REG_AGG_INT_EVENT_12 0x166068 5771 #define XSDM_REG_AGG_INT_EVENT_13 0x16606c 5772 #define XSDM_REG_AGG_INT_EVENT_14 0x166070 5773 #define XSDM_REG_AGG_INT_EVENT_2 0x166040 5774 #define XSDM_REG_AGG_INT_EVENT_3 0x166044 5775 #define XSDM_REG_AGG_INT_EVENT_4 0x166048 5776 #define XSDM_REG_AGG_INT_EVENT_5 0x16604c 5777 #define XSDM_REG_AGG_INT_EVENT_6 0x166050 5778 #define XSDM_REG_AGG_INT_EVENT_7 0x166054 5779 #define XSDM_REG_AGG_INT_EVENT_8 0x166058 5780 #define XSDM_REG_AGG_INT_EVENT_9 0x16605c 5781 /* [RW 1] For each aggregated interrupt index whether the mode is normal (0) 5782 or auto-mask-mode (1) */ 5783 #define XSDM_REG_AGG_INT_MODE_0 0x1661b8 5784 #define XSDM_REG_AGG_INT_MODE_1 0x1661bc 5785 /* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */ 5786 #define XSDM_REG_CFC_RSP_START_ADDR 0x166008 5787 /* [RW 16] The maximum value of the completion counter #0 */ 5788 #define XSDM_REG_CMP_COUNTER_MAX0 0x16601c 5789 /* [RW 16] The maximum value of the completion counter #1 */ 5790 #define XSDM_REG_CMP_COUNTER_MAX1 0x166020 5791 /* [RW 16] The maximum value of the completion counter #2 */ 5792 #define XSDM_REG_CMP_COUNTER_MAX2 0x166024 5793 /* [RW 16] The maximum value of the completion counter #3 */ 5794 #define XSDM_REG_CMP_COUNTER_MAX3 0x166028 5795 /* [RW 13] The start address in the internal RAM for the completion 5796 counters. */ 5797 #define XSDM_REG_CMP_COUNTER_START_ADDR 0x16600c 5798 #define XSDM_REG_ENABLE_IN1 0x166238 5799 #define XSDM_REG_ENABLE_IN2 0x16623c 5800 #define XSDM_REG_ENABLE_OUT1 0x166240 5801 #define XSDM_REG_ENABLE_OUT2 0x166244 5802 /* [RW 4] The initial number of messages that can be sent to the pxp control 5803 interface without receiving any ACK. */ 5804 #define XSDM_REG_INIT_CREDIT_PXP_CTRL 0x1664bc 5805 /* [ST 32] The number of ACK after placement messages received */ 5806 #define XSDM_REG_NUM_OF_ACK_AFTER_PLACE 0x16627c 5807 /* [ST 32] The number of packet end messages received from the parser */ 5808 #define XSDM_REG_NUM_OF_PKT_END_MSG 0x166274 5809 /* [ST 32] The number of requests received from the pxp async if */ 5810 #define XSDM_REG_NUM_OF_PXP_ASYNC_REQ 0x166278 5811 /* [ST 32] The number of commands received in queue 0 */ 5812 #define XSDM_REG_NUM_OF_Q0_CMD 0x166248 5813 /* [ST 32] The number of commands received in queue 10 */ 5814 #define XSDM_REG_NUM_OF_Q10_CMD 0x16626c 5815 /* [ST 32] The number of commands received in queue 11 */ 5816 #define XSDM_REG_NUM_OF_Q11_CMD 0x166270 5817 /* [ST 32] The number of commands received in queue 1 */ 5818 #define XSDM_REG_NUM_OF_Q1_CMD 0x16624c 5819 /* [ST 32] The number of commands received in queue 3 */ 5820 #define XSDM_REG_NUM_OF_Q3_CMD 0x166250 5821 /* [ST 32] The number of commands received in queue 4 */ 5822 #define XSDM_REG_NUM_OF_Q4_CMD 0x166254 5823 /* [ST 32] The number of commands received in queue 5 */ 5824 #define XSDM_REG_NUM_OF_Q5_CMD 0x166258 5825 /* [ST 32] The number of commands received in queue 6 */ 5826 #define XSDM_REG_NUM_OF_Q6_CMD 0x16625c 5827 /* [ST 32] The number of commands received in queue 7 */ 5828 #define XSDM_REG_NUM_OF_Q7_CMD 0x166260 5829 /* [ST 32] The number of commands received in queue 8 */ 5830 #define XSDM_REG_NUM_OF_Q8_CMD 0x166264 5831 /* [ST 32] The number of commands received in queue 9 */ 5832 #define XSDM_REG_NUM_OF_Q9_CMD 0x166268 5833 /* [RW 13] The start address in the internal RAM for queue counters */ 5834 #define XSDM_REG_Q_COUNTER_START_ADDR 0x166010 5835 /* [W 17] Generate an operation after completion; bit-16 is 5836 * AggVectIdx_valid; bits 15:8 are AggVectIdx; bits 7:5 are the TRIG and 5837 * bits 4:0 are the T124Param[4:0] */ 5838 #define XSDM_REG_OPERATION_GEN 0x1664c4 5839 /* [R 1] pxp_ctrl rd_data fifo empty in sdm_dma_rsp block */ 5840 #define XSDM_REG_RSP_PXP_CTRL_RDATA_EMPTY 0x166548 5841 /* [R 1] parser fifo empty in sdm_sync block */ 5842 #define XSDM_REG_SYNC_PARSER_EMPTY 0x166550 5843 /* [R 1] parser serial fifo empty in sdm_sync block */ 5844 #define XSDM_REG_SYNC_SYNC_EMPTY 0x166558 5845 /* [RW 32] Tick for timer counter. Applicable only when 5846 ~xsdm_registers_timer_tick_enable.timer_tick_enable =1 */ 5847 #define XSDM_REG_TIMER_TICK 0x166000 5848 /* [RW 32] Interrupt mask register #0 read/write */ 5849 #define XSDM_REG_XSDM_INT_MASK_0 0x16629c 5850 #define XSDM_REG_XSDM_INT_MASK_1 0x1662ac 5851 /* [R 32] Interrupt register #0 read */ 5852 #define XSDM_REG_XSDM_INT_STS_0 0x166290 5853 #define XSDM_REG_XSDM_INT_STS_1 0x1662a0 5854 /* [RW 11] Parity mask register #0 read/write */ 5855 #define XSDM_REG_XSDM_PRTY_MASK 0x1662bc 5856 /* [R 11] Parity register #0 read */ 5857 #define XSDM_REG_XSDM_PRTY_STS 0x1662b0 5858 /* [RC 11] Parity register #0 read clear */ 5859 #define XSDM_REG_XSDM_PRTY_STS_CLR 0x1662b4 5860 /* [RW 5] The number of time_slots in the arbitration cycle */ 5861 #define XSEM_REG_ARB_CYCLE_SIZE 0x280034 5862 /* [RW 3] The source that is associated with arbitration element 0. Source 5863 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 5864 sleeping thread with priority 1; 4- sleeping thread with priority 2 */ 5865 #define XSEM_REG_ARB_ELEMENT0 0x280020 5866 /* [RW 3] The source that is associated with arbitration element 1. Source 5867 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 5868 sleeping thread with priority 1; 4- sleeping thread with priority 2. 5869 Could not be equal to register ~xsem_registers_arb_element0.arb_element0 */ 5870 #define XSEM_REG_ARB_ELEMENT1 0x280024 5871 /* [RW 3] The source that is associated with arbitration element 2. Source 5872 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 5873 sleeping thread with priority 1; 4- sleeping thread with priority 2. 5874 Could not be equal to register ~xsem_registers_arb_element0.arb_element0 5875 and ~xsem_registers_arb_element1.arb_element1 */ 5876 #define XSEM_REG_ARB_ELEMENT2 0x280028 5877 /* [RW 3] The source that is associated with arbitration element 3. Source 5878 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 5879 sleeping thread with priority 1; 4- sleeping thread with priority 2.Could 5880 not be equal to register ~xsem_registers_arb_element0.arb_element0 and 5881 ~xsem_registers_arb_element1.arb_element1 and 5882 ~xsem_registers_arb_element2.arb_element2 */ 5883 #define XSEM_REG_ARB_ELEMENT3 0x28002c 5884 /* [RW 3] The source that is associated with arbitration element 4. Source 5885 decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3- 5886 sleeping thread with priority 1; 4- sleeping thread with priority 2. 5887 Could not be equal to register ~xsem_registers_arb_element0.arb_element0 5888 and ~xsem_registers_arb_element1.arb_element1 and 5889 ~xsem_registers_arb_element2.arb_element2 and 5890 ~xsem_registers_arb_element3.arb_element3 */ 5891 #define XSEM_REG_ARB_ELEMENT4 0x280030 5892 #define XSEM_REG_ENABLE_IN 0x2800a4 5893 #define XSEM_REG_ENABLE_OUT 0x2800a8 5894 /* [RW 32] This address space contains all registers and memories that are 5895 placed in SEM_FAST block. The SEM_FAST registers are described in 5896 appendix B. In order to access the sem_fast registers the base address 5897 ~fast_memory.fast_memory should be added to eachsem_fast register offset. */ 5898 #define XSEM_REG_FAST_MEMORY 0x2a0000 5899 /* [RW 1] Disables input messages from FIC0 May be updated during run_time 5900 by the microcode */ 5901 #define XSEM_REG_FIC0_DISABLE 0x280224 5902 /* [RW 1] Disables input messages from FIC1 May be updated during run_time 5903 by the microcode */ 5904 #define XSEM_REG_FIC1_DISABLE 0x280234 5905 /* [RW 15] Interrupt table Read and write access to it is not possible in 5906 the middle of the work */ 5907 #define XSEM_REG_INT_TABLE 0x280400 5908 /* [ST 24] Statistics register. The number of messages that entered through 5909 FIC0 */ 5910 #define XSEM_REG_MSG_NUM_FIC0 0x280000 5911 /* [ST 24] Statistics register. The number of messages that entered through 5912 FIC1 */ 5913 #define XSEM_REG_MSG_NUM_FIC1 0x280004 5914 /* [ST 24] Statistics register. The number of messages that were sent to 5915 FOC0 */ 5916 #define XSEM_REG_MSG_NUM_FOC0 0x280008 5917 /* [ST 24] Statistics register. The number of messages that were sent to 5918 FOC1 */ 5919 #define XSEM_REG_MSG_NUM_FOC1 0x28000c 5920 /* [ST 24] Statistics register. The number of messages that were sent to 5921 FOC2 */ 5922 #define XSEM_REG_MSG_NUM_FOC2 0x280010 5923 /* [ST 24] Statistics register. The number of messages that were sent to 5924 FOC3 */ 5925 #define XSEM_REG_MSG_NUM_FOC3 0x280014 5926 /* [RW 1] Disables input messages from the passive buffer May be updated 5927 during run_time by the microcode */ 5928 #define XSEM_REG_PAS_DISABLE 0x28024c 5929 /* [WB 128] Debug only. Passive buffer memory */ 5930 #define XSEM_REG_PASSIVE_BUFFER 0x282000 5931 /* [WB 46] pram memory. B45 is parity; b[44:0] - data. */ 5932 #define XSEM_REG_PRAM 0x2c0000 5933 /* [R 16] Valid sleeping threads indication have bit per thread */ 5934 #define XSEM_REG_SLEEP_THREADS_VALID 0x28026c 5935 /* [R 1] EXT_STORE FIFO is empty in sem_slow_ls_ext */ 5936 #define XSEM_REG_SLOW_EXT_STORE_EMPTY 0x2802a0 5937 /* [RW 16] List of free threads . There is a bit per thread. */ 5938 #define XSEM_REG_THREADS_LIST 0x2802e4 5939 /* [RW 3] The arbitration scheme of time_slot 0 */ 5940 #define XSEM_REG_TS_0_AS 0x280038 5941 /* [RW 3] The arbitration scheme of time_slot 10 */ 5942 #define XSEM_REG_TS_10_AS 0x280060 5943 /* [RW 3] The arbitration scheme of time_slot 11 */ 5944 #define XSEM_REG_TS_11_AS 0x280064 5945 /* [RW 3] The arbitration scheme of time_slot 12 */ 5946 #define XSEM_REG_TS_12_AS 0x280068 5947 /* [RW 3] The arbitration scheme of time_slot 13 */ 5948 #define XSEM_REG_TS_13_AS 0x28006c 5949 /* [RW 3] The arbitration scheme of time_slot 14 */ 5950 #define XSEM_REG_TS_14_AS 0x280070 5951 /* [RW 3] The arbitration scheme of time_slot 15 */ 5952 #define XSEM_REG_TS_15_AS 0x280074 5953 /* [RW 3] The arbitration scheme of time_slot 16 */ 5954 #define XSEM_REG_TS_16_AS 0x280078 5955 /* [RW 3] The arbitration scheme of time_slot 17 */ 5956 #define XSEM_REG_TS_17_AS 0x28007c 5957 /* [RW 3] The arbitration scheme of time_slot 18 */ 5958 #define XSEM_REG_TS_18_AS 0x280080 5959 /* [RW 3] The arbitration scheme of time_slot 1 */ 5960 #define XSEM_REG_TS_1_AS 0x28003c 5961 /* [RW 3] The arbitration scheme of time_slot 2 */ 5962 #define XSEM_REG_TS_2_AS 0x280040 5963 /* [RW 3] The arbitration scheme of time_slot 3 */ 5964 #define XSEM_REG_TS_3_AS 0x280044 5965 /* [RW 3] The arbitration scheme of time_slot 4 */ 5966 #define XSEM_REG_TS_4_AS 0x280048 5967 /* [RW 3] The arbitration scheme of time_slot 5 */ 5968 #define XSEM_REG_TS_5_AS 0x28004c 5969 /* [RW 3] The arbitration scheme of time_slot 6 */ 5970 #define XSEM_REG_TS_6_AS 0x280050 5971 /* [RW 3] The arbitration scheme of time_slot 7 */ 5972 #define XSEM_REG_TS_7_AS 0x280054 5973 /* [RW 3] The arbitration scheme of time_slot 8 */ 5974 #define XSEM_REG_TS_8_AS 0x280058 5975 /* [RW 3] The arbitration scheme of time_slot 9 */ 5976 #define XSEM_REG_TS_9_AS 0x28005c 5977 /* [W 7] VF or PF ID for reset error bit. Values 0-63 reset error bit for 64 5978 * VF; values 64-67 reset error for 4 PF; values 68-127 are not valid. */ 5979 #define XSEM_REG_VFPF_ERR_NUM 0x280380 5980 /* [RW 32] Interrupt mask register #0 read/write */ 5981 #define XSEM_REG_XSEM_INT_MASK_0 0x280110 5982 #define XSEM_REG_XSEM_INT_MASK_1 0x280120 5983 /* [R 32] Interrupt register #0 read */ 5984 #define XSEM_REG_XSEM_INT_STS_0 0x280104 5985 #define XSEM_REG_XSEM_INT_STS_1 0x280114 5986 /* [RW 32] Parity mask register #0 read/write */ 5987 #define XSEM_REG_XSEM_PRTY_MASK_0 0x280130 5988 #define XSEM_REG_XSEM_PRTY_MASK_1 0x280140 5989 /* [R 32] Parity register #0 read */ 5990 #define XSEM_REG_XSEM_PRTY_STS_0 0x280124 5991 #define XSEM_REG_XSEM_PRTY_STS_1 0x280134 5992 /* [RC 32] Parity register #0 read clear */ 5993 #define XSEM_REG_XSEM_PRTY_STS_CLR_0 0x280128 5994 #define XSEM_REG_XSEM_PRTY_STS_CLR_1 0x280138 5995 #define MCPR_ACCESS_LOCK_LOCK (1L<<31) 5996 #define MCPR_NVM_ACCESS_ENABLE_EN (1L<<0) 5997 #define MCPR_NVM_ACCESS_ENABLE_WR_EN (1L<<1) 5998 #define MCPR_NVM_ADDR_NVM_ADDR_VALUE (0xffffffL<<0) 5999 #define MCPR_NVM_CFG4_FLASH_SIZE (0x7L<<0) 6000 #define MCPR_NVM_COMMAND_DOIT (1L<<4) 6001 #define MCPR_NVM_COMMAND_DONE (1L<<3) 6002 #define MCPR_NVM_COMMAND_FIRST (1L<<7) 6003 #define MCPR_NVM_COMMAND_LAST (1L<<8) 6004 #define MCPR_NVM_COMMAND_WR (1L<<5) 6005 #define MCPR_NVM_SW_ARB_ARB_ARB1 (1L<<9) 6006 #define MCPR_NVM_SW_ARB_ARB_REQ_CLR1 (1L<<5) 6007 #define MCPR_NVM_SW_ARB_ARB_REQ_SET1 (1L<<1) 6008 #define BIGMAC_REGISTER_BMAC_CONTROL (0x00<<3) 6009 #define BIGMAC_REGISTER_BMAC_XGXS_CONTROL (0x01<<3) 6010 #define BIGMAC_REGISTER_CNT_MAX_SIZE (0x05<<3) 6011 #define BIGMAC_REGISTER_RX_CONTROL (0x21<<3) 6012 #define BIGMAC_REGISTER_RX_LLFC_MSG_FLDS (0x46<<3) 6013 #define BIGMAC_REGISTER_RX_LSS_STATUS (0x43<<3) 6014 #define BIGMAC_REGISTER_RX_MAX_SIZE (0x23<<3) 6015 #define BIGMAC_REGISTER_RX_STAT_GR64 (0x26<<3) 6016 #define BIGMAC_REGISTER_RX_STAT_GRIPJ (0x42<<3) 6017 #define BIGMAC_REGISTER_TX_CONTROL (0x07<<3) 6018 #define BIGMAC_REGISTER_TX_MAX_SIZE (0x09<<3) 6019 #define BIGMAC_REGISTER_TX_PAUSE_THRESHOLD (0x0A<<3) 6020 #define BIGMAC_REGISTER_TX_SOURCE_ADDR (0x08<<3) 6021 #define BIGMAC_REGISTER_TX_STAT_GTBYT (0x20<<3) 6022 #define BIGMAC_REGISTER_TX_STAT_GTPKT (0x0C<<3) 6023 #define BIGMAC2_REGISTER_BMAC_CONTROL (0x00<<3) 6024 #define BIGMAC2_REGISTER_BMAC_XGXS_CONTROL (0x01<<3) 6025 #define BIGMAC2_REGISTER_CNT_MAX_SIZE (0x05<<3) 6026 #define BIGMAC2_REGISTER_PFC_CONTROL (0x06<<3) 6027 #define BIGMAC2_REGISTER_RX_CONTROL (0x3A<<3) 6028 #define BIGMAC2_REGISTER_RX_LLFC_MSG_FLDS (0x62<<3) 6029 #define BIGMAC2_REGISTER_RX_LSS_STAT (0x3E<<3) 6030 #define BIGMAC2_REGISTER_RX_MAX_SIZE (0x3C<<3) 6031 #define BIGMAC2_REGISTER_RX_STAT_GR64 (0x40<<3) 6032 #define BIGMAC2_REGISTER_RX_STAT_GRIPJ (0x5f<<3) 6033 #define BIGMAC2_REGISTER_RX_STAT_GRPP (0x51<<3) 6034 #define BIGMAC2_REGISTER_TX_CONTROL (0x1C<<3) 6035 #define BIGMAC2_REGISTER_TX_MAX_SIZE (0x1E<<3) 6036 #define BIGMAC2_REGISTER_TX_PAUSE_CONTROL (0x20<<3) 6037 #define BIGMAC2_REGISTER_TX_SOURCE_ADDR (0x1D<<3) 6038 #define BIGMAC2_REGISTER_TX_STAT_GTBYT (0x39<<3) 6039 #define BIGMAC2_REGISTER_TX_STAT_GTPOK (0x22<<3) 6040 #define BIGMAC2_REGISTER_TX_STAT_GTPP (0x24<<3) 6041 #define EMAC_LED_1000MB_OVERRIDE (1L<<1) 6042 #define EMAC_LED_100MB_OVERRIDE (1L<<2) 6043 #define EMAC_LED_10MB_OVERRIDE (1L<<3) 6044 #define EMAC_LED_2500MB_OVERRIDE (1L<<12) 6045 #define EMAC_LED_OVERRIDE (1L<<0) 6046 #define EMAC_LED_TRAFFIC (1L<<6) 6047 #define EMAC_MDIO_COMM_COMMAND_ADDRESS (0L<<26) 6048 #define EMAC_MDIO_COMM_COMMAND_READ_22 (2L<<26) 6049 #define EMAC_MDIO_COMM_COMMAND_READ_45 (3L<<26) 6050 #define EMAC_MDIO_COMM_COMMAND_WRITE_22 (1L<<26) 6051 #define EMAC_MDIO_COMM_COMMAND_WRITE_45 (1L<<26) 6052 #define EMAC_MDIO_COMM_DATA (0xffffL<<0) 6053 #define EMAC_MDIO_COMM_START_BUSY (1L<<29) 6054 #define EMAC_MDIO_MODE_AUTO_POLL (1L<<4) 6055 #define EMAC_MDIO_MODE_CLAUSE_45 (1L<<31) 6056 #define EMAC_MDIO_MODE_CLOCK_CNT (0x3ffL<<16) 6057 #define EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT 16 6058 #define EMAC_MDIO_STATUS_10MB (1L<<1) 6059 #define EMAC_MODE_25G_MODE (1L<<5) 6060 #define EMAC_MODE_HALF_DUPLEX (1L<<1) 6061 #define EMAC_MODE_PORT_GMII (2L<<2) 6062 #define EMAC_MODE_PORT_MII (1L<<2) 6063 #define EMAC_MODE_PORT_MII_10M (3L<<2) 6064 #define EMAC_MODE_RESET (1L<<0) 6065 #define EMAC_REG_EMAC_LED 0xc 6066 #define EMAC_REG_EMAC_MAC_MATCH 0x10 6067 #define EMAC_REG_EMAC_MDIO_COMM 0xac 6068 #define EMAC_REG_EMAC_MDIO_MODE 0xb4 6069 #define EMAC_REG_EMAC_MDIO_STATUS 0xb0 6070 #define EMAC_REG_EMAC_MODE 0x0 6071 #define EMAC_REG_EMAC_RX_MODE 0xc8 6072 #define EMAC_REG_EMAC_RX_MTU_SIZE 0x9c 6073 #define EMAC_REG_EMAC_RX_STAT_AC 0x180 6074 #define EMAC_REG_EMAC_RX_STAT_AC_28 0x1f4 6075 #define EMAC_REG_EMAC_RX_STAT_AC_COUNT 23 6076 #define EMAC_REG_EMAC_TX_MODE 0xbc 6077 #define EMAC_REG_EMAC_TX_STAT_AC 0x280 6078 #define EMAC_REG_EMAC_TX_STAT_AC_COUNT 22 6079 #define EMAC_REG_RX_PFC_MODE 0x320 6080 #define EMAC_REG_RX_PFC_MODE_PRIORITIES (1L<<2) 6081 #define EMAC_REG_RX_PFC_MODE_RX_EN (1L<<1) 6082 #define EMAC_REG_RX_PFC_MODE_TX_EN (1L<<0) 6083 #define EMAC_REG_RX_PFC_PARAM 0x324 6084 #define EMAC_REG_RX_PFC_PARAM_OPCODE_BITSHIFT 0 6085 #define EMAC_REG_RX_PFC_PARAM_PRIORITY_EN_BITSHIFT 16 6086 #define EMAC_REG_RX_PFC_STATS_XOFF_RCVD 0x328 6087 #define EMAC_REG_RX_PFC_STATS_XOFF_RCVD_COUNT (0xffff<<0) 6088 #define EMAC_REG_RX_PFC_STATS_XOFF_SENT 0x330 6089 #define EMAC_REG_RX_PFC_STATS_XOFF_SENT_COUNT (0xffff<<0) 6090 #define EMAC_REG_RX_PFC_STATS_XON_RCVD 0x32c 6091 #define EMAC_REG_RX_PFC_STATS_XON_RCVD_COUNT (0xffff<<0) 6092 #define EMAC_REG_RX_PFC_STATS_XON_SENT 0x334 6093 #define EMAC_REG_RX_PFC_STATS_XON_SENT_COUNT (0xffff<<0) 6094 #define EMAC_RX_MODE_FLOW_EN (1L<<2) 6095 #define EMAC_RX_MODE_KEEP_MAC_CONTROL (1L<<3) 6096 #define EMAC_RX_MODE_KEEP_VLAN_TAG (1L<<10) 6097 #define EMAC_RX_MODE_PROMISCUOUS (1L<<8) 6098 #define EMAC_RX_MODE_RESET (1L<<0) 6099 #define EMAC_RX_MTU_SIZE_JUMBO_ENA (1L<<31) 6100 #define EMAC_TX_MODE_EXT_PAUSE_EN (1L<<3) 6101 #define EMAC_TX_MODE_FLOW_EN (1L<<4) 6102 #define EMAC_TX_MODE_RESET (1L<<0) 6103 #define MISC_REGISTERS_GPIO_0 0 6104 #define MISC_REGISTERS_GPIO_1 1 6105 #define MISC_REGISTERS_GPIO_2 2 6106 #define MISC_REGISTERS_GPIO_3 3 6107 #define MISC_REGISTERS_GPIO_CLR_POS 16 6108 #define MISC_REGISTERS_GPIO_FLOAT (0xffL<<24) 6109 #define MISC_REGISTERS_GPIO_FLOAT_POS 24 6110 #define MISC_REGISTERS_GPIO_HIGH 1 6111 #define MISC_REGISTERS_GPIO_INPUT_HI_Z 2 6112 #define MISC_REGISTERS_GPIO_INT_CLR_POS 24 6113 #define MISC_REGISTERS_GPIO_INT_OUTPUT_CLR 0 6114 #define MISC_REGISTERS_GPIO_INT_OUTPUT_SET 1 6115 #define MISC_REGISTERS_GPIO_INT_SET_POS 16 6116 #define MISC_REGISTERS_GPIO_LOW 0 6117 #define MISC_REGISTERS_GPIO_OUTPUT_HIGH 1 6118 #define MISC_REGISTERS_GPIO_OUTPUT_LOW 0 6119 #define MISC_REGISTERS_GPIO_PORT_SHIFT 4 6120 #define MISC_REGISTERS_GPIO_SET_POS 8 6121 #define MISC_REGISTERS_RESET_REG_1_CLEAR 0x588 6122 #define MISC_REGISTERS_RESET_REG_1_RST_BRB1 (0x1<<0) 6123 #define MISC_REGISTERS_RESET_REG_1_RST_DORQ (0x1<<19) 6124 #define MISC_REGISTERS_RESET_REG_1_RST_HC (0x1<<29) 6125 #define MISC_REGISTERS_RESET_REG_1_RST_NIG (0x1<<7) 6126 #define MISC_REGISTERS_RESET_REG_1_RST_PXP (0x1<<26) 6127 #define MISC_REGISTERS_RESET_REG_1_RST_PXPV (0x1<<27) 6128 #define MISC_REGISTERS_RESET_REG_1_RST_XSEM (0x1<<22) 6129 #define MISC_REGISTERS_RESET_REG_1_SET 0x584 6130 #define MISC_REGISTERS_RESET_REG_2_CLEAR 0x598 6131 #define MISC_REGISTERS_RESET_REG_2_MSTAT0 (0x1<<24) 6132 #define MISC_REGISTERS_RESET_REG_2_MSTAT1 (0x1<<25) 6133 #define MISC_REGISTERS_RESET_REG_2_PGLC (0x1<<19) 6134 #define MISC_REGISTERS_RESET_REG_2_RST_ATC (0x1<<17) 6135 #define MISC_REGISTERS_RESET_REG_2_RST_BMAC0 (0x1<<0) 6136 #define MISC_REGISTERS_RESET_REG_2_RST_BMAC1 (0x1<<1) 6137 #define MISC_REGISTERS_RESET_REG_2_RST_EMAC0 (0x1<<2) 6138 #define MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE (0x1<<14) 6139 #define MISC_REGISTERS_RESET_REG_2_RST_EMAC1 (0x1<<3) 6140 #define MISC_REGISTERS_RESET_REG_2_RST_EMAC1_HARD_CORE (0x1<<15) 6141 #define MISC_REGISTERS_RESET_REG_2_RST_GRC (0x1<<4) 6142 #define MISC_REGISTERS_RESET_REG_2_RST_MCP_N_HARD_CORE_RST_B (0x1<<6) 6143 #define MISC_REGISTERS_RESET_REG_2_RST_MCP_N_RESET_CMN_CORE (0x1<<8) 6144 #define MISC_REGISTERS_RESET_REG_2_RST_MCP_N_RESET_CMN_CPU (0x1<<7) 6145 #define MISC_REGISTERS_RESET_REG_2_RST_MCP_N_RESET_REG_HARD_CORE (0x1<<5) 6146 #define MISC_REGISTERS_RESET_REG_2_RST_MDIO (0x1<<13) 6147 #define MISC_REGISTERS_RESET_REG_2_RST_MISC_CORE (0x1<<11) 6148 #define MISC_REGISTERS_RESET_REG_2_RST_PCI_MDIO (0x1<<13) 6149 #define MISC_REGISTERS_RESET_REG_2_RST_RBCN (0x1<<9) 6150 #define MISC_REGISTERS_RESET_REG_2_SET 0x594 6151 #define MISC_REGISTERS_RESET_REG_2_UMAC0 (0x1<<20) 6152 #define MISC_REGISTERS_RESET_REG_2_UMAC1 (0x1<<21) 6153 #define MISC_REGISTERS_RESET_REG_2_XMAC (0x1<<22) 6154 #define MISC_REGISTERS_RESET_REG_2_XMAC_SOFT (0x1<<23) 6155 #define MISC_REGISTERS_RESET_REG_3_CLEAR 0x5a8 6156 #define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_IDDQ (0x1<<1) 6157 #define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN (0x1<<2) 6158 #define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN_SD (0x1<<3) 6159 #define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_RSTB_HW (0x1<<0) 6160 #define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_IDDQ (0x1<<5) 6161 #define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN (0x1<<6) 6162 #define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN_SD (0x1<<7) 6163 #define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_RSTB_HW (0x1<<4) 6164 #define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_TXD_FIFO_RSTB (0x1<<8) 6165 #define MISC_REGISTERS_RESET_REG_3_SET 0x5a4 6166 #define MISC_REGISTERS_SPIO_4 4 6167 #define MISC_REGISTERS_SPIO_5 5 6168 #define MISC_REGISTERS_SPIO_7 7 6169 #define MISC_REGISTERS_SPIO_CLR_POS 16 6170 #define MISC_REGISTERS_SPIO_FLOAT (0xffL<<24) 6171 #define MISC_REGISTERS_SPIO_FLOAT_POS 24 6172 #define MISC_REGISTERS_SPIO_INPUT_HI_Z 2 6173 #define MISC_REGISTERS_SPIO_INT_OLD_SET_POS 16 6174 #define MISC_REGISTERS_SPIO_OUTPUT_HIGH 1 6175 #define MISC_REGISTERS_SPIO_OUTPUT_LOW 0 6176 #define MISC_REGISTERS_SPIO_SET_POS 8 6177 #define MISC_SPIO_CLR_POS 16 6178 #define MISC_SPIO_FLOAT (0xffL<<24) 6179 #define MISC_SPIO_FLOAT_POS 24 6180 #define MISC_SPIO_INPUT_HI_Z 2 6181 #define MISC_SPIO_INT_OLD_SET_POS 16 6182 #define MISC_SPIO_OUTPUT_HIGH 1 6183 #define MISC_SPIO_OUTPUT_LOW 0 6184 #define MISC_SPIO_SET_POS 8 6185 #define MISC_SPIO_SPIO4 0x10 6186 #define MISC_SPIO_SPIO5 0x20 6187 #define HW_LOCK_MAX_RESOURCE_VALUE 31 6188 #define HW_LOCK_RESOURCE_DCBX_ADMIN_MIB 13 6189 #define HW_LOCK_RESOURCE_DRV_FLAGS 10 6190 #define HW_LOCK_RESOURCE_GPIO 1 6191 #define HW_LOCK_RESOURCE_MDIO 0 6192 #define HW_LOCK_RESOURCE_NVRAM 12 6193 #define HW_LOCK_RESOURCE_PORT0_ATT_MASK 3 6194 #define HW_LOCK_RESOURCE_RECOVERY_LEADER_0 8 6195 #define HW_LOCK_RESOURCE_RECOVERY_LEADER_1 9 6196 #define HW_LOCK_RESOURCE_RECOVERY_REG 11 6197 #define HW_LOCK_RESOURCE_RESET 5 6198 #define HW_LOCK_RESOURCE_SPIO 2 6199 #define AEU_INPUTS_ATTN_BITS_ATC_HW_INTERRUPT (0x1<<4) 6200 #define AEU_INPUTS_ATTN_BITS_ATC_PARITY_ERROR (0x1<<5) 6201 #define AEU_INPUTS_ATTN_BITS_BRB_HW_INTERRUPT (0x1<<19) 6202 #define AEU_INPUTS_ATTN_BITS_BRB_PARITY_ERROR (0x1<<18) 6203 #define AEU_INPUTS_ATTN_BITS_CCM_HW_INTERRUPT (0x1<<31) 6204 #define AEU_INPUTS_ATTN_BITS_CCM_PARITY_ERROR (0x1<<30) 6205 #define AEU_INPUTS_ATTN_BITS_CDU_HW_INTERRUPT (0x1<<9) 6206 #define AEU_INPUTS_ATTN_BITS_CDU_PARITY_ERROR (0x1<<8) 6207 #define AEU_INPUTS_ATTN_BITS_CFC_HW_INTERRUPT (0x1<<7) 6208 #define AEU_INPUTS_ATTN_BITS_CFC_PARITY_ERROR (0x1<<6) 6209 #define AEU_INPUTS_ATTN_BITS_CSDM_HW_INTERRUPT (0x1<<29) 6210 #define AEU_INPUTS_ATTN_BITS_CSDM_PARITY_ERROR (0x1<<28) 6211 #define AEU_INPUTS_ATTN_BITS_CSEMI_HW_INTERRUPT (0x1<<1) 6212 #define AEU_INPUTS_ATTN_BITS_CSEMI_PARITY_ERROR (0x1<<0) 6213 #define AEU_INPUTS_ATTN_BITS_DEBUG_PARITY_ERROR (0x1<<18) 6214 #define AEU_INPUTS_ATTN_BITS_DMAE_HW_INTERRUPT (0x1<<11) 6215 #define AEU_INPUTS_ATTN_BITS_DMAE_PARITY_ERROR (0x1<<10) 6216 #define AEU_INPUTS_ATTN_BITS_DOORBELLQ_HW_INTERRUPT (0x1<<13) 6217 #define AEU_INPUTS_ATTN_BITS_DOORBELLQ_PARITY_ERROR (0x1<<12) 6218 #define AEU_INPUTS_ATTN_BITS_GPIO0_FUNCTION_0 (0x1<<2) 6219 #define AEU_INPUTS_ATTN_BITS_IGU_PARITY_ERROR (0x1<<12) 6220 #define AEU_INPUTS_ATTN_BITS_MCP_LATCHED_ROM_PARITY (0x1<<28) 6221 #define AEU_INPUTS_ATTN_BITS_MCP_LATCHED_SCPAD_PARITY (0x1<<31) 6222 #define AEU_INPUTS_ATTN_BITS_MCP_LATCHED_UMP_RX_PARITY (0x1<<29) 6223 #define AEU_INPUTS_ATTN_BITS_MCP_LATCHED_UMP_TX_PARITY (0x1<<30) 6224 #define AEU_INPUTS_ATTN_BITS_MISC_HW_INTERRUPT (0x1<<15) 6225 #define AEU_INPUTS_ATTN_BITS_MISC_PARITY_ERROR (0x1<<14) 6226 #define AEU_INPUTS_ATTN_BITS_NIG_PARITY_ERROR (0x1<<14) 6227 #define AEU_INPUTS_ATTN_BITS_PARSER_PARITY_ERROR (0x1<<20) 6228 #define AEU_INPUTS_ATTN_BITS_PBCLIENT_HW_INTERRUPT (0x1<<31) 6229 #define AEU_INPUTS_ATTN_BITS_PBCLIENT_PARITY_ERROR (0x1<<30) 6230 #define AEU_INPUTS_ATTN_BITS_PBF_PARITY_ERROR (0x1<<0) 6231 #define AEU_INPUTS_ATTN_BITS_PGLUE_HW_INTERRUPT (0x1<<2) 6232 #define AEU_INPUTS_ATTN_BITS_PGLUE_PARITY_ERROR (0x1<<3) 6233 #define AEU_INPUTS_ATTN_BITS_PXPPCICLOCKCLIENT_HW_INTERRUPT (0x1<<5) 6234 #define AEU_INPUTS_ATTN_BITS_PXPPCICLOCKCLIENT_PARITY_ERROR (0x1<<4) 6235 #define AEU_INPUTS_ATTN_BITS_PXP_HW_INTERRUPT (0x1<<3) 6236 #define AEU_INPUTS_ATTN_BITS_PXP_PARITY_ERROR (0x1<<2) 6237 #define AEU_INPUTS_ATTN_BITS_QM_HW_INTERRUPT (0x1<<3) 6238 #define AEU_INPUTS_ATTN_BITS_QM_PARITY_ERROR (0x1<<2) 6239 #define AEU_INPUTS_ATTN_BITS_SEARCHER_PARITY_ERROR (0x1<<22) 6240 #define AEU_INPUTS_ATTN_BITS_SPIO5 (0x1<<15) 6241 #define AEU_INPUTS_ATTN_BITS_TCM_HW_INTERRUPT (0x1<<27) 6242 #define AEU_INPUTS_ATTN_BITS_TCM_PARITY_ERROR (0x1<<26) 6243 #define AEU_INPUTS_ATTN_BITS_TIMERS_HW_INTERRUPT (0x1<<5) 6244 #define AEU_INPUTS_ATTN_BITS_TIMERS_PARITY_ERROR (0x1<<4) 6245 #define AEU_INPUTS_ATTN_BITS_TSDM_HW_INTERRUPT (0x1<<25) 6246 #define AEU_INPUTS_ATTN_BITS_TSDM_PARITY_ERROR (0x1<<24) 6247 #define AEU_INPUTS_ATTN_BITS_TSEMI_HW_INTERRUPT (0x1<<29) 6248 #define AEU_INPUTS_ATTN_BITS_TSEMI_PARITY_ERROR (0x1<<28) 6249 #define AEU_INPUTS_ATTN_BITS_UCM_HW_INTERRUPT (0x1<<23) 6250 #define AEU_INPUTS_ATTN_BITS_UCM_PARITY_ERROR (0x1<<22) 6251 #define AEU_INPUTS_ATTN_BITS_UPB_HW_INTERRUPT (0x1<<27) 6252 #define AEU_INPUTS_ATTN_BITS_UPB_PARITY_ERROR (0x1<<26) 6253 #define AEU_INPUTS_ATTN_BITS_USDM_HW_INTERRUPT (0x1<<21) 6254 #define AEU_INPUTS_ATTN_BITS_USDM_PARITY_ERROR (0x1<<20) 6255 #define AEU_INPUTS_ATTN_BITS_USEMI_HW_INTERRUPT (0x1<<25) 6256 #define AEU_INPUTS_ATTN_BITS_USEMI_PARITY_ERROR (0x1<<24) 6257 #define AEU_INPUTS_ATTN_BITS_VAUX_PCI_CORE_PARITY_ERROR (0x1<<16) 6258 #define AEU_INPUTS_ATTN_BITS_XCM_HW_INTERRUPT (0x1<<9) 6259 #define AEU_INPUTS_ATTN_BITS_XCM_PARITY_ERROR (0x1<<8) 6260 #define AEU_INPUTS_ATTN_BITS_XSDM_HW_INTERRUPT (0x1<<7) 6261 #define AEU_INPUTS_ATTN_BITS_XSDM_PARITY_ERROR (0x1<<6) 6262 #define AEU_INPUTS_ATTN_BITS_XSEMI_HW_INTERRUPT (0x1<<11) 6263 #define AEU_INPUTS_ATTN_BITS_XSEMI_PARITY_ERROR (0x1<<10) 6264 6265 #define AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0 (0x1<<5) 6266 #define AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_1 (0x1<<9) 6267 6268 #define RESERVED_GENERAL_ATTENTION_BIT_0 0 6269 6270 #define EVEREST_GEN_ATTN_IN_USE_MASK 0x7ffe0 6271 #define EVEREST_LATCHED_ATTN_IN_USE_MASK 0xffe00000 6272 6273 #define RESERVED_GENERAL_ATTENTION_BIT_6 6 6274 #define RESERVED_GENERAL_ATTENTION_BIT_7 7 6275 #define RESERVED_GENERAL_ATTENTION_BIT_8 8 6276 #define RESERVED_GENERAL_ATTENTION_BIT_9 9 6277 #define RESERVED_GENERAL_ATTENTION_BIT_10 10 6278 #define RESERVED_GENERAL_ATTENTION_BIT_11 11 6279 #define RESERVED_GENERAL_ATTENTION_BIT_12 12 6280 #define RESERVED_GENERAL_ATTENTION_BIT_13 13 6281 #define RESERVED_GENERAL_ATTENTION_BIT_14 14 6282 #define RESERVED_GENERAL_ATTENTION_BIT_15 15 6283 #define RESERVED_GENERAL_ATTENTION_BIT_16 16 6284 #define RESERVED_GENERAL_ATTENTION_BIT_17 17 6285 #define RESERVED_GENERAL_ATTENTION_BIT_18 18 6286 #define RESERVED_GENERAL_ATTENTION_BIT_19 19 6287 #define RESERVED_GENERAL_ATTENTION_BIT_20 20 6288 #define RESERVED_GENERAL_ATTENTION_BIT_21 21 6289 6290 /* storm asserts attention bits */ 6291 #define TSTORM_FATAL_ASSERT_ATTENTION_BIT RESERVED_GENERAL_ATTENTION_BIT_7 6292 #define USTORM_FATAL_ASSERT_ATTENTION_BIT RESERVED_GENERAL_ATTENTION_BIT_8 6293 #define CSTORM_FATAL_ASSERT_ATTENTION_BIT RESERVED_GENERAL_ATTENTION_BIT_9 6294 #define XSTORM_FATAL_ASSERT_ATTENTION_BIT RESERVED_GENERAL_ATTENTION_BIT_10 6295 6296 /* mcp error attention bit */ 6297 #define MCP_FATAL_ASSERT_ATTENTION_BIT RESERVED_GENERAL_ATTENTION_BIT_11 6298 6299 /*E1H NIG status sync attention mapped to group 4-7*/ 6300 #define LINK_SYNC_ATTENTION_BIT_FUNC_0 RESERVED_GENERAL_ATTENTION_BIT_12 6301 #define LINK_SYNC_ATTENTION_BIT_FUNC_1 RESERVED_GENERAL_ATTENTION_BIT_13 6302 #define LINK_SYNC_ATTENTION_BIT_FUNC_2 RESERVED_GENERAL_ATTENTION_BIT_14 6303 #define LINK_SYNC_ATTENTION_BIT_FUNC_3 RESERVED_GENERAL_ATTENTION_BIT_15 6304 #define LINK_SYNC_ATTENTION_BIT_FUNC_4 RESERVED_GENERAL_ATTENTION_BIT_16 6305 #define LINK_SYNC_ATTENTION_BIT_FUNC_5 RESERVED_GENERAL_ATTENTION_BIT_17 6306 #define LINK_SYNC_ATTENTION_BIT_FUNC_6 RESERVED_GENERAL_ATTENTION_BIT_18 6307 #define LINK_SYNC_ATTENTION_BIT_FUNC_7 RESERVED_GENERAL_ATTENTION_BIT_19 6308 6309 6310 #define LATCHED_ATTN_RBCR 23 6311 #define LATCHED_ATTN_RBCT 24 6312 #define LATCHED_ATTN_RBCN 25 6313 #define LATCHED_ATTN_RBCU 26 6314 #define LATCHED_ATTN_RBCP 27 6315 #define LATCHED_ATTN_TIMEOUT_GRC 28 6316 #define LATCHED_ATTN_RSVD_GRC 29 6317 #define LATCHED_ATTN_ROM_PARITY_MCP 30 6318 #define LATCHED_ATTN_UM_RX_PARITY_MCP 31 6319 #define LATCHED_ATTN_UM_TX_PARITY_MCP 32 6320 #define LATCHED_ATTN_SCPAD_PARITY_MCP 33 6321 6322 #define GENERAL_ATTEN_WORD(atten_name) ((94 + atten_name) / 32) 6323 #define GENERAL_ATTEN_OFFSET(atten_name)\ 6324 (1UL << ((94 + atten_name) % 32)) 6325 /* 6326 * This file defines GRC base address for every block. 6327 * This file is included by chipsim, asm microcode and cpp microcode. 6328 * These values are used in Design.xml on regBase attribute 6329 * Use the base with the generated offsets of specific registers. 6330 */ 6331 6332 #define GRCBASE_PXPCS 0x000000 6333 #define GRCBASE_PCICONFIG 0x002000 6334 #define GRCBASE_PCIREG 0x002400 6335 #define GRCBASE_EMAC0 0x008000 6336 #define GRCBASE_EMAC1 0x008400 6337 #define GRCBASE_DBU 0x008800 6338 #define GRCBASE_MISC 0x00A000 6339 #define GRCBASE_DBG 0x00C000 6340 #define GRCBASE_NIG 0x010000 6341 #define GRCBASE_XCM 0x020000 6342 #define GRCBASE_PRS 0x040000 6343 #define GRCBASE_SRCH 0x040400 6344 #define GRCBASE_TSDM 0x042000 6345 #define GRCBASE_TCM 0x050000 6346 #define GRCBASE_BRB1 0x060000 6347 #define GRCBASE_MCP 0x080000 6348 #define GRCBASE_UPB 0x0C1000 6349 #define GRCBASE_CSDM 0x0C2000 6350 #define GRCBASE_USDM 0x0C4000 6351 #define GRCBASE_CCM 0x0D0000 6352 #define GRCBASE_UCM 0x0E0000 6353 #define GRCBASE_CDU 0x101000 6354 #define GRCBASE_DMAE 0x102000 6355 #define GRCBASE_PXP 0x103000 6356 #define GRCBASE_CFC 0x104000 6357 #define GRCBASE_HC 0x108000 6358 #define GRCBASE_PXP2 0x120000 6359 #define GRCBASE_PBF 0x140000 6360 #define GRCBASE_UMAC0 0x160000 6361 #define GRCBASE_UMAC1 0x160400 6362 #define GRCBASE_XPB 0x161000 6363 #define GRCBASE_MSTAT0 0x162000 6364 #define GRCBASE_MSTAT1 0x162800 6365 #define GRCBASE_XMAC0 0x163000 6366 #define GRCBASE_XMAC1 0x163800 6367 #define GRCBASE_TIMERS 0x164000 6368 #define GRCBASE_XSDM 0x166000 6369 #define GRCBASE_QM 0x168000 6370 #define GRCBASE_DQ 0x170000 6371 #define GRCBASE_TSEM 0x180000 6372 #define GRCBASE_CSEM 0x200000 6373 #define GRCBASE_XSEM 0x280000 6374 #define GRCBASE_USEM 0x300000 6375 #define GRCBASE_MISC_AEU GRCBASE_MISC 6376 6377 6378 /* offset of configuration space in the pci core register */ 6379 #define PCICFG_OFFSET 0x2000 6380 #define PCICFG_VENDOR_ID_OFFSET 0x00 6381 #define PCICFG_DEVICE_ID_OFFSET 0x02 6382 #define PCICFG_COMMAND_OFFSET 0x04 6383 #define PCICFG_COMMAND_IO_SPACE (1<<0) 6384 #define PCICFG_COMMAND_MEM_SPACE (1<<1) 6385 #define PCICFG_COMMAND_BUS_MASTER (1<<2) 6386 #define PCICFG_COMMAND_SPECIAL_CYCLES (1<<3) 6387 #define PCICFG_COMMAND_MWI_CYCLES (1<<4) 6388 #define PCICFG_COMMAND_VGA_SNOOP (1<<5) 6389 #define PCICFG_COMMAND_PERR_ENA (1<<6) 6390 #define PCICFG_COMMAND_STEPPING (1<<7) 6391 #define PCICFG_COMMAND_SERR_ENA (1<<8) 6392 #define PCICFG_COMMAND_FAST_B2B (1<<9) 6393 #define PCICFG_COMMAND_INT_DISABLE (1<<10) 6394 #define PCICFG_COMMAND_RESERVED (0x1f<<11) 6395 #define PCICFG_STATUS_OFFSET 0x06 6396 #define PCICFG_REVISION_ID_OFFSET 0x08 6397 #define PCICFG_REVESION_ID_MASK 0xff 6398 #define PCICFG_REVESION_ID_ERROR_VAL 0xff 6399 #define PCICFG_CACHE_LINE_SIZE 0x0c 6400 #define PCICFG_LATENCY_TIMER 0x0d 6401 #define PCICFG_BAR_1_LOW 0x10 6402 #define PCICFG_BAR_1_HIGH 0x14 6403 #define PCICFG_BAR_2_LOW 0x18 6404 #define PCICFG_BAR_2_HIGH 0x1c 6405 #define PCICFG_SUBSYSTEM_VENDOR_ID_OFFSET 0x2c 6406 #define PCICFG_SUBSYSTEM_ID_OFFSET 0x2e 6407 #define PCICFG_INT_LINE 0x3c 6408 #define PCICFG_INT_PIN 0x3d 6409 #define PCICFG_PM_CAPABILITY 0x48 6410 #define PCICFG_PM_CAPABILITY_VERSION (0x3<<16) 6411 #define PCICFG_PM_CAPABILITY_CLOCK (1<<19) 6412 #define PCICFG_PM_CAPABILITY_RESERVED (1<<20) 6413 #define PCICFG_PM_CAPABILITY_DSI (1<<21) 6414 #define PCICFG_PM_CAPABILITY_AUX_CURRENT (0x7<<22) 6415 #define PCICFG_PM_CAPABILITY_D1_SUPPORT (1<<25) 6416 #define PCICFG_PM_CAPABILITY_D2_SUPPORT (1<<26) 6417 #define PCICFG_PM_CAPABILITY_PME_IN_D0 (1<<27) 6418 #define PCICFG_PM_CAPABILITY_PME_IN_D1 (1<<28) 6419 #define PCICFG_PM_CAPABILITY_PME_IN_D2 (1<<29) 6420 #define PCICFG_PM_CAPABILITY_PME_IN_D3_HOT (1<<30) 6421 #define PCICFG_PM_CAPABILITY_PME_IN_D3_COLD (1<<31) 6422 #define PCICFG_PM_CSR_OFFSET 0x4c 6423 #define PCICFG_PM_CSR_STATE (0x3<<0) 6424 #define PCICFG_PM_CSR_PME_ENABLE (1<<8) 6425 #define PCICFG_PM_CSR_PME_STATUS (1<<15) 6426 #define PCICFG_MSI_CAP_ID_OFFSET 0x58 6427 #define PCICFG_MSI_CONTROL_ENABLE (0x1<<16) 6428 #define PCICFG_MSI_CONTROL_MCAP (0x7<<17) 6429 #define PCICFG_MSI_CONTROL_MENA (0x7<<20) 6430 #define PCICFG_MSI_CONTROL_64_BIT_ADDR_CAP (0x1<<23) 6431 #define PCICFG_MSI_CONTROL_MSI_PVMASK_CAPABLE (0x1<<24) 6432 #define PCICFG_GRC_ADDRESS 0x78 6433 #define PCICFG_GRC_DATA 0x80 6434 #define PCICFG_ME_REGISTER 0x98 6435 #define PCICFG_MSIX_CAP_ID_OFFSET 0xa0 6436 #define PCICFG_MSIX_CONTROL_TABLE_SIZE (0x7ff<<16) 6437 #define PCICFG_MSIX_CONTROL_RESERVED (0x7<<27) 6438 #define PCICFG_MSIX_CONTROL_FUNC_MASK (0x1<<30) 6439 #define PCICFG_MSIX_CONTROL_MSIX_ENABLE (0x1<<31) 6440 6441 #define PCICFG_DEVICE_CONTROL 0xb4 6442 #define PCICFG_DEVICE_STATUS 0xb6 6443 #define PCICFG_DEVICE_STATUS_CORR_ERR_DET (1<<0) 6444 #define PCICFG_DEVICE_STATUS_NON_FATAL_ERR_DET (1<<1) 6445 #define PCICFG_DEVICE_STATUS_FATAL_ERR_DET (1<<2) 6446 #define PCICFG_DEVICE_STATUS_UNSUP_REQ_DET (1<<3) 6447 #define PCICFG_DEVICE_STATUS_AUX_PWR_DET (1<<4) 6448 #define PCICFG_DEVICE_STATUS_NO_PEND (1<<5) 6449 #define PCICFG_LINK_CONTROL 0xbc 6450 6451 6452 #define BAR_USTRORM_INTMEM 0x400000 6453 #define BAR_CSTRORM_INTMEM 0x410000 6454 #define BAR_XSTRORM_INTMEM 0x420000 6455 #define BAR_TSTRORM_INTMEM 0x430000 6456 6457 /* for accessing the IGU in case of status block ACK */ 6458 #define BAR_IGU_INTMEM 0x440000 6459 6460 #define BAR_DOORBELL_OFFSET 0x800000 6461 6462 #define BAR_ME_REGISTER 0x450000 6463 6464 /* config_2 offset */ 6465 #define GRC_CONFIG_2_SIZE_REG 0x408 6466 #define PCI_CONFIG_2_BAR1_SIZE (0xfL<<0) 6467 #define PCI_CONFIG_2_BAR1_SIZE_DISABLED (0L<<0) 6468 #define PCI_CONFIG_2_BAR1_SIZE_64K (1L<<0) 6469 #define PCI_CONFIG_2_BAR1_SIZE_128K (2L<<0) 6470 #define PCI_CONFIG_2_BAR1_SIZE_256K (3L<<0) 6471 #define PCI_CONFIG_2_BAR1_SIZE_512K (4L<<0) 6472 #define PCI_CONFIG_2_BAR1_SIZE_1M (5L<<0) 6473 #define PCI_CONFIG_2_BAR1_SIZE_2M (6L<<0) 6474 #define PCI_CONFIG_2_BAR1_SIZE_4M (7L<<0) 6475 #define PCI_CONFIG_2_BAR1_SIZE_8M (8L<<0) 6476 #define PCI_CONFIG_2_BAR1_SIZE_16M (9L<<0) 6477 #define PCI_CONFIG_2_BAR1_SIZE_32M (10L<<0) 6478 #define PCI_CONFIG_2_BAR1_SIZE_64M (11L<<0) 6479 #define PCI_CONFIG_2_BAR1_SIZE_128M (12L<<0) 6480 #define PCI_CONFIG_2_BAR1_SIZE_256M (13L<<0) 6481 #define PCI_CONFIG_2_BAR1_SIZE_512M (14L<<0) 6482 #define PCI_CONFIG_2_BAR1_SIZE_1G (15L<<0) 6483 #define PCI_CONFIG_2_BAR1_64ENA (1L<<4) 6484 #define PCI_CONFIG_2_EXP_ROM_RETRY (1L<<5) 6485 #define PCI_CONFIG_2_CFG_CYCLE_RETRY (1L<<6) 6486 #define PCI_CONFIG_2_FIRST_CFG_DONE (1L<<7) 6487 #define PCI_CONFIG_2_EXP_ROM_SIZE (0xffL<<8) 6488 #define PCI_CONFIG_2_EXP_ROM_SIZE_DISABLED (0L<<8) 6489 #define PCI_CONFIG_2_EXP_ROM_SIZE_2K (1L<<8) 6490 #define PCI_CONFIG_2_EXP_ROM_SIZE_4K (2L<<8) 6491 #define PCI_CONFIG_2_EXP_ROM_SIZE_8K (3L<<8) 6492 #define PCI_CONFIG_2_EXP_ROM_SIZE_16K (4L<<8) 6493 #define PCI_CONFIG_2_EXP_ROM_SIZE_32K (5L<<8) 6494 #define PCI_CONFIG_2_EXP_ROM_SIZE_64K (6L<<8) 6495 #define PCI_CONFIG_2_EXP_ROM_SIZE_128K (7L<<8) 6496 #define PCI_CONFIG_2_EXP_ROM_SIZE_256K (8L<<8) 6497 #define PCI_CONFIG_2_EXP_ROM_SIZE_512K (9L<<8) 6498 #define PCI_CONFIG_2_EXP_ROM_SIZE_1M (10L<<8) 6499 #define PCI_CONFIG_2_EXP_ROM_SIZE_2M (11L<<8) 6500 #define PCI_CONFIG_2_EXP_ROM_SIZE_4M (12L<<8) 6501 #define PCI_CONFIG_2_EXP_ROM_SIZE_8M (13L<<8) 6502 #define PCI_CONFIG_2_EXP_ROM_SIZE_16M (14L<<8) 6503 #define PCI_CONFIG_2_EXP_ROM_SIZE_32M (15L<<8) 6504 #define PCI_CONFIG_2_BAR_PREFETCH (1L<<16) 6505 #define PCI_CONFIG_2_RESERVED0 (0x7fffL<<17) 6506 6507 /* config_3 offset */ 6508 #define GRC_CONFIG_3_SIZE_REG 0x40c 6509 #define PCI_CONFIG_3_STICKY_BYTE (0xffL<<0) 6510 #define PCI_CONFIG_3_FORCE_PME (1L<<24) 6511 #define PCI_CONFIG_3_PME_STATUS (1L<<25) 6512 #define PCI_CONFIG_3_PME_ENABLE (1L<<26) 6513 #define PCI_CONFIG_3_PM_STATE (0x3L<<27) 6514 #define PCI_CONFIG_3_VAUX_PRESET (1L<<30) 6515 #define PCI_CONFIG_3_PCI_POWER (1L<<31) 6516 6517 #define GRC_BAR2_CONFIG 0x4e0 6518 #define PCI_CONFIG_2_BAR2_SIZE (0xfL<<0) 6519 #define PCI_CONFIG_2_BAR2_SIZE_DISABLED (0L<<0) 6520 #define PCI_CONFIG_2_BAR2_SIZE_64K (1L<<0) 6521 #define PCI_CONFIG_2_BAR2_SIZE_128K (2L<<0) 6522 #define PCI_CONFIG_2_BAR2_SIZE_256K (3L<<0) 6523 #define PCI_CONFIG_2_BAR2_SIZE_512K (4L<<0) 6524 #define PCI_CONFIG_2_BAR2_SIZE_1M (5L<<0) 6525 #define PCI_CONFIG_2_BAR2_SIZE_2M (6L<<0) 6526 #define PCI_CONFIG_2_BAR2_SIZE_4M (7L<<0) 6527 #define PCI_CONFIG_2_BAR2_SIZE_8M (8L<<0) 6528 #define PCI_CONFIG_2_BAR2_SIZE_16M (9L<<0) 6529 #define PCI_CONFIG_2_BAR2_SIZE_32M (10L<<0) 6530 #define PCI_CONFIG_2_BAR2_SIZE_64M (11L<<0) 6531 #define PCI_CONFIG_2_BAR2_SIZE_128M (12L<<0) 6532 #define PCI_CONFIG_2_BAR2_SIZE_256M (13L<<0) 6533 #define PCI_CONFIG_2_BAR2_SIZE_512M (14L<<0) 6534 #define PCI_CONFIG_2_BAR2_SIZE_1G (15L<<0) 6535 #define PCI_CONFIG_2_BAR2_64ENA (1L<<4) 6536 6537 #define PCI_PM_DATA_A 0x410 6538 #define PCI_PM_DATA_B 0x414 6539 #define PCI_ID_VAL1 0x434 6540 #define PCI_ID_VAL2 0x438 6541 #define PCI_ID_VAL3 0x43c 6542 6543 #define GRC_CONFIG_REG_VF_MSIX_CONTROL 0x61C 6544 #define GRC_CONFIG_REG_PF_INIT_VF 0x624 6545 #define GRC_CR_PF_INIT_VF_PF_FIRST_VF_NUM_MASK 0xf 6546 /* First VF_NUM for PF is encoded in this register. 6547 * The number of VFs assigned to a PF is assumed to be a multiple of 8. 6548 * Software should program these bits based on Total Number of VFs \ 6549 * programmed for each PF. 6550 * Since registers from 0x000-0x7ff are split across functions, each PF will 6551 * have the same location for the same 4 bits 6552 */ 6553 6554 #define PXPCS_TL_CONTROL_5 0x814 6555 #define PXPCS_TL_CONTROL_5_UNKNOWNTYPE_ERR_ATTN (1 << 29) /*WC*/ 6556 #define PXPCS_TL_CONTROL_5_BOUNDARY4K_ERR_ATTN (1 << 28) /*WC*/ 6557 #define PXPCS_TL_CONTROL_5_MRRS_ERR_ATTN (1 << 27) /*WC*/ 6558 #define PXPCS_TL_CONTROL_5_MPS_ERR_ATTN (1 << 26) /*WC*/ 6559 #define PXPCS_TL_CONTROL_5_TTX_BRIDGE_FORWARD_ERR (1 << 25) /*WC*/ 6560 #define PXPCS_TL_CONTROL_5_TTX_TXINTF_OVERFLOW (1 << 24) /*WC*/ 6561 #define PXPCS_TL_CONTROL_5_PHY_ERR_ATTN (1 << 23) /*RO*/ 6562 #define PXPCS_TL_CONTROL_5_DL_ERR_ATTN (1 << 22) /*RO*/ 6563 #define PXPCS_TL_CONTROL_5_TTX_ERR_NP_TAG_IN_USE (1 << 21) /*WC*/ 6564 #define PXPCS_TL_CONTROL_5_TRX_ERR_UNEXP_RTAG (1 << 20) /*WC*/ 6565 #define PXPCS_TL_CONTROL_5_PRI_SIG_TARGET_ABORT1 (1 << 19) /*WC*/ 6566 #define PXPCS_TL_CONTROL_5_ERR_UNSPPORT1 (1 << 18) /*WC*/ 6567 #define PXPCS_TL_CONTROL_5_ERR_ECRC1 (1 << 17) /*WC*/ 6568 #define PXPCS_TL_CONTROL_5_ERR_MALF_TLP1 (1 << 16) /*WC*/ 6569 #define PXPCS_TL_CONTROL_5_ERR_RX_OFLOW1 (1 << 15) /*WC*/ 6570 #define PXPCS_TL_CONTROL_5_ERR_UNEXP_CPL1 (1 << 14) /*WC*/ 6571 #define PXPCS_TL_CONTROL_5_ERR_MASTER_ABRT1 (1 << 13) /*WC*/ 6572 #define PXPCS_TL_CONTROL_5_ERR_CPL_TIMEOUT1 (1 << 12) /*WC*/ 6573 #define PXPCS_TL_CONTROL_5_ERR_FC_PRTL1 (1 << 11) /*WC*/ 6574 #define PXPCS_TL_CONTROL_5_ERR_PSND_TLP1 (1 << 10) /*WC*/ 6575 #define PXPCS_TL_CONTROL_5_PRI_SIG_TARGET_ABORT (1 << 9) /*WC*/ 6576 #define PXPCS_TL_CONTROL_5_ERR_UNSPPORT (1 << 8) /*WC*/ 6577 #define PXPCS_TL_CONTROL_5_ERR_ECRC (1 << 7) /*WC*/ 6578 #define PXPCS_TL_CONTROL_5_ERR_MALF_TLP (1 << 6) /*WC*/ 6579 #define PXPCS_TL_CONTROL_5_ERR_RX_OFLOW (1 << 5) /*WC*/ 6580 #define PXPCS_TL_CONTROL_5_ERR_UNEXP_CPL (1 << 4) /*WC*/ 6581 #define PXPCS_TL_CONTROL_5_ERR_MASTER_ABRT (1 << 3) /*WC*/ 6582 #define PXPCS_TL_CONTROL_5_ERR_CPL_TIMEOUT (1 << 2) /*WC*/ 6583 #define PXPCS_TL_CONTROL_5_ERR_FC_PRTL (1 << 1) /*WC*/ 6584 #define PXPCS_TL_CONTROL_5_ERR_PSND_TLP (1 << 0) /*WC*/ 6585 6586 6587 #define PXPCS_TL_FUNC345_STAT 0x854 6588 #define PXPCS_TL_FUNC345_STAT_PRI_SIG_TARGET_ABORT4 (1 << 29) /* WC */ 6589 #define PXPCS_TL_FUNC345_STAT_ERR_UNSPPORT4\ 6590 (1 << 28) /* Unsupported Request Error Status in function4, if \ 6591 set, generate pcie_err_attn output when this error is seen. WC */ 6592 #define PXPCS_TL_FUNC345_STAT_ERR_ECRC4\ 6593 (1 << 27) /* ECRC Error TLP Status Status in function 4, if set, \ 6594 generate pcie_err_attn output when this error is seen.. WC */ 6595 #define PXPCS_TL_FUNC345_STAT_ERR_MALF_TLP4\ 6596 (1 << 26) /* Malformed TLP Status Status in function 4, if set, \ 6597 generate pcie_err_attn output when this error is seen.. WC */ 6598 #define PXPCS_TL_FUNC345_STAT_ERR_RX_OFLOW4\ 6599 (1 << 25) /* Receiver Overflow Status Status in function 4, if \ 6600 set, generate pcie_err_attn output when this error is seen.. WC \ 6601 */ 6602 #define PXPCS_TL_FUNC345_STAT_ERR_UNEXP_CPL4\ 6603 (1 << 24) /* Unexpected Completion Status Status in function 4, \ 6604 if set, generate pcie_err_attn output when this error is seen. WC \ 6605 */ 6606 #define PXPCS_TL_FUNC345_STAT_ERR_MASTER_ABRT4\ 6607 (1 << 23) /* Receive UR Statusin function 4. If set, generate \ 6608 pcie_err_attn output when this error is seen. WC */ 6609 #define PXPCS_TL_FUNC345_STAT_ERR_CPL_TIMEOUT4\ 6610 (1 << 22) /* Completer Timeout Status Status in function 4, if \ 6611 set, generate pcie_err_attn output when this error is seen. WC */ 6612 #define PXPCS_TL_FUNC345_STAT_ERR_FC_PRTL4\ 6613 (1 << 21) /* Flow Control Protocol Error Status Status in \ 6614 function 4, if set, generate pcie_err_attn output when this error \ 6615 is seen. WC */ 6616 #define PXPCS_TL_FUNC345_STAT_ERR_PSND_TLP4\ 6617 (1 << 20) /* Poisoned Error Status Status in function 4, if set, \ 6618 generate pcie_err_attn output when this error is seen.. WC */ 6619 #define PXPCS_TL_FUNC345_STAT_PRI_SIG_TARGET_ABORT3 (1 << 19) /* WC */ 6620 #define PXPCS_TL_FUNC345_STAT_ERR_UNSPPORT3\ 6621 (1 << 18) /* Unsupported Request Error Status in function3, if \ 6622 set, generate pcie_err_attn output when this error is seen. WC */ 6623 #define PXPCS_TL_FUNC345_STAT_ERR_ECRC3\ 6624 (1 << 17) /* ECRC Error TLP Status Status in function 3, if set, \ 6625 generate pcie_err_attn output when this error is seen.. WC */ 6626 #define PXPCS_TL_FUNC345_STAT_ERR_MALF_TLP3\ 6627 (1 << 16) /* Malformed TLP Status Status in function 3, if set, \ 6628 generate pcie_err_attn output when this error is seen.. WC */ 6629 #define PXPCS_TL_FUNC345_STAT_ERR_RX_OFLOW3\ 6630 (1 << 15) /* Receiver Overflow Status Status in function 3, if \ 6631 set, generate pcie_err_attn output when this error is seen.. WC \ 6632 */ 6633 #define PXPCS_TL_FUNC345_STAT_ERR_UNEXP_CPL3\ 6634 (1 << 14) /* Unexpected Completion Status Status in function 3, \ 6635 if set, generate pcie_err_attn output when this error is seen. WC \ 6636 */ 6637 #define PXPCS_TL_FUNC345_STAT_ERR_MASTER_ABRT3\ 6638 (1 << 13) /* Receive UR Statusin function 3. If set, generate \ 6639 pcie_err_attn output when this error is seen. WC */ 6640 #define PXPCS_TL_FUNC345_STAT_ERR_CPL_TIMEOUT3\ 6641 (1 << 12) /* Completer Timeout Status Status in function 3, if \ 6642 set, generate pcie_err_attn output when this error is seen. WC */ 6643 #define PXPCS_TL_FUNC345_STAT_ERR_FC_PRTL3\ 6644 (1 << 11) /* Flow Control Protocol Error Status Status in \ 6645 function 3, if set, generate pcie_err_attn output when this error \ 6646 is seen. WC */ 6647 #define PXPCS_TL_FUNC345_STAT_ERR_PSND_TLP3\ 6648 (1 << 10) /* Poisoned Error Status Status in function 3, if set, \ 6649 generate pcie_err_attn output when this error is seen.. WC */ 6650 #define PXPCS_TL_FUNC345_STAT_PRI_SIG_TARGET_ABORT2 (1 << 9) /* WC */ 6651 #define PXPCS_TL_FUNC345_STAT_ERR_UNSPPORT2\ 6652 (1 << 8) /* Unsupported Request Error Status for Function 2, if \ 6653 set, generate pcie_err_attn output when this error is seen. WC */ 6654 #define PXPCS_TL_FUNC345_STAT_ERR_ECRC2\ 6655 (1 << 7) /* ECRC Error TLP Status Status for Function 2, if set, \ 6656 generate pcie_err_attn output when this error is seen.. WC */ 6657 #define PXPCS_TL_FUNC345_STAT_ERR_MALF_TLP2\ 6658 (1 << 6) /* Malformed TLP Status Status for Function 2, if set, \ 6659 generate pcie_err_attn output when this error is seen.. WC */ 6660 #define PXPCS_TL_FUNC345_STAT_ERR_RX_OFLOW2\ 6661 (1 << 5) /* Receiver Overflow Status Status for Function 2, if \ 6662 set, generate pcie_err_attn output when this error is seen.. WC \ 6663 */ 6664 #define PXPCS_TL_FUNC345_STAT_ERR_UNEXP_CPL2\ 6665 (1 << 4) /* Unexpected Completion Status Status for Function 2, \ 6666 if set, generate pcie_err_attn output when this error is seen. WC \ 6667 */ 6668 #define PXPCS_TL_FUNC345_STAT_ERR_MASTER_ABRT2\ 6669 (1 << 3) /* Receive UR Statusfor Function 2. If set, generate \ 6670 pcie_err_attn output when this error is seen. WC */ 6671 #define PXPCS_TL_FUNC345_STAT_ERR_CPL_TIMEOUT2\ 6672 (1 << 2) /* Completer Timeout Status Status for Function 2, if \ 6673 set, generate pcie_err_attn output when this error is seen. WC */ 6674 #define PXPCS_TL_FUNC345_STAT_ERR_FC_PRTL2\ 6675 (1 << 1) /* Flow Control Protocol Error Status Status for \ 6676 Function 2, if set, generate pcie_err_attn output when this error \ 6677 is seen. WC */ 6678 #define PXPCS_TL_FUNC345_STAT_ERR_PSND_TLP2\ 6679 (1 << 0) /* Poisoned Error Status Status for Function 2, if set, \ 6680 generate pcie_err_attn output when this error is seen.. WC */ 6681 6682 6683 #define PXPCS_TL_FUNC678_STAT 0x85C 6684 #define PXPCS_TL_FUNC678_STAT_PRI_SIG_TARGET_ABORT7 (1 << 29) /* WC */ 6685 #define PXPCS_TL_FUNC678_STAT_ERR_UNSPPORT7\ 6686 (1 << 28) /* Unsupported Request Error Status in function7, if \ 6687 set, generate pcie_err_attn output when this error is seen. WC */ 6688 #define PXPCS_TL_FUNC678_STAT_ERR_ECRC7\ 6689 (1 << 27) /* ECRC Error TLP Status Status in function 7, if set, \ 6690 generate pcie_err_attn output when this error is seen.. WC */ 6691 #define PXPCS_TL_FUNC678_STAT_ERR_MALF_TLP7\ 6692 (1 << 26) /* Malformed TLP Status Status in function 7, if set, \ 6693 generate pcie_err_attn output when this error is seen.. WC */ 6694 #define PXPCS_TL_FUNC678_STAT_ERR_RX_OFLOW7\ 6695 (1 << 25) /* Receiver Overflow Status Status in function 7, if \ 6696 set, generate pcie_err_attn output when this error is seen.. WC \ 6697 */ 6698 #define PXPCS_TL_FUNC678_STAT_ERR_UNEXP_CPL7\ 6699 (1 << 24) /* Unexpected Completion Status Status in function 7, \ 6700 if set, generate pcie_err_attn output when this error is seen. WC \ 6701 */ 6702 #define PXPCS_TL_FUNC678_STAT_ERR_MASTER_ABRT7\ 6703 (1 << 23) /* Receive UR Statusin function 7. If set, generate \ 6704 pcie_err_attn output when this error is seen. WC */ 6705 #define PXPCS_TL_FUNC678_STAT_ERR_CPL_TIMEOUT7\ 6706 (1 << 22) /* Completer Timeout Status Status in function 7, if \ 6707 set, generate pcie_err_attn output when this error is seen. WC */ 6708 #define PXPCS_TL_FUNC678_STAT_ERR_FC_PRTL7\ 6709 (1 << 21) /* Flow Control Protocol Error Status Status in \ 6710 function 7, if set, generate pcie_err_attn output when this error \ 6711 is seen. WC */ 6712 #define PXPCS_TL_FUNC678_STAT_ERR_PSND_TLP7\ 6713 (1 << 20) /* Poisoned Error Status Status in function 7, if set, \ 6714 generate pcie_err_attn output when this error is seen.. WC */ 6715 #define PXPCS_TL_FUNC678_STAT_PRI_SIG_TARGET_ABORT6 (1 << 19) /* WC */ 6716 #define PXPCS_TL_FUNC678_STAT_ERR_UNSPPORT6\ 6717 (1 << 18) /* Unsupported Request Error Status in function6, if \ 6718 set, generate pcie_err_attn output when this error is seen. WC */ 6719 #define PXPCS_TL_FUNC678_STAT_ERR_ECRC6\ 6720 (1 << 17) /* ECRC Error TLP Status Status in function 6, if set, \ 6721 generate pcie_err_attn output when this error is seen.. WC */ 6722 #define PXPCS_TL_FUNC678_STAT_ERR_MALF_TLP6\ 6723 (1 << 16) /* Malformed TLP Status Status in function 6, if set, \ 6724 generate pcie_err_attn output when this error is seen.. WC */ 6725 #define PXPCS_TL_FUNC678_STAT_ERR_RX_OFLOW6\ 6726 (1 << 15) /* Receiver Overflow Status Status in function 6, if \ 6727 set, generate pcie_err_attn output when this error is seen.. WC \ 6728 */ 6729 #define PXPCS_TL_FUNC678_STAT_ERR_UNEXP_CPL6\ 6730 (1 << 14) /* Unexpected Completion Status Status in function 6, \ 6731 if set, generate pcie_err_attn output when this error is seen. WC \ 6732 */ 6733 #define PXPCS_TL_FUNC678_STAT_ERR_MASTER_ABRT6\ 6734 (1 << 13) /* Receive UR Statusin function 6. If set, generate \ 6735 pcie_err_attn output when this error is seen. WC */ 6736 #define PXPCS_TL_FUNC678_STAT_ERR_CPL_TIMEOUT6\ 6737 (1 << 12) /* Completer Timeout Status Status in function 6, if \ 6738 set, generate pcie_err_attn output when this error is seen. WC */ 6739 #define PXPCS_TL_FUNC678_STAT_ERR_FC_PRTL6\ 6740 (1 << 11) /* Flow Control Protocol Error Status Status in \ 6741 function 6, if set, generate pcie_err_attn output when this error \ 6742 is seen. WC */ 6743 #define PXPCS_TL_FUNC678_STAT_ERR_PSND_TLP6\ 6744 (1 << 10) /* Poisoned Error Status Status in function 6, if set, \ 6745 generate pcie_err_attn output when this error is seen.. WC */ 6746 #define PXPCS_TL_FUNC678_STAT_PRI_SIG_TARGET_ABORT5 (1 << 9) /* WC */ 6747 #define PXPCS_TL_FUNC678_STAT_ERR_UNSPPORT5\ 6748 (1 << 8) /* Unsupported Request Error Status for Function 5, if \ 6749 set, generate pcie_err_attn output when this error is seen. WC */ 6750 #define PXPCS_TL_FUNC678_STAT_ERR_ECRC5\ 6751 (1 << 7) /* ECRC Error TLP Status Status for Function 5, if set, \ 6752 generate pcie_err_attn output when this error is seen.. WC */ 6753 #define PXPCS_TL_FUNC678_STAT_ERR_MALF_TLP5\ 6754 (1 << 6) /* Malformed TLP Status Status for Function 5, if set, \ 6755 generate pcie_err_attn output when this error is seen.. WC */ 6756 #define PXPCS_TL_FUNC678_STAT_ERR_RX_OFLOW5\ 6757 (1 << 5) /* Receiver Overflow Status Status for Function 5, if \ 6758 set, generate pcie_err_attn output when this error is seen.. WC \ 6759 */ 6760 #define PXPCS_TL_FUNC678_STAT_ERR_UNEXP_CPL5\ 6761 (1 << 4) /* Unexpected Completion Status Status for Function 5, \ 6762 if set, generate pcie_err_attn output when this error is seen. WC \ 6763 */ 6764 #define PXPCS_TL_FUNC678_STAT_ERR_MASTER_ABRT5\ 6765 (1 << 3) /* Receive UR Statusfor Function 5. If set, generate \ 6766 pcie_err_attn output when this error is seen. WC */ 6767 #define PXPCS_TL_FUNC678_STAT_ERR_CPL_TIMEOUT5\ 6768 (1 << 2) /* Completer Timeout Status Status for Function 5, if \ 6769 set, generate pcie_err_attn output when this error is seen. WC */ 6770 #define PXPCS_TL_FUNC678_STAT_ERR_FC_PRTL5\ 6771 (1 << 1) /* Flow Control Protocol Error Status Status for \ 6772 Function 5, if set, generate pcie_err_attn output when this error \ 6773 is seen. WC */ 6774 #define PXPCS_TL_FUNC678_STAT_ERR_PSND_TLP5\ 6775 (1 << 0) /* Poisoned Error Status Status for Function 5, if set, \ 6776 generate pcie_err_attn output when this error is seen.. WC */ 6777 6778 6779 #define BAR_USTRORM_INTMEM 0x400000 6780 #define BAR_CSTRORM_INTMEM 0x410000 6781 #define BAR_XSTRORM_INTMEM 0x420000 6782 #define BAR_TSTRORM_INTMEM 0x430000 6783 6784 /* for accessing the IGU in case of status block ACK */ 6785 #define BAR_IGU_INTMEM 0x440000 6786 6787 #define BAR_DOORBELL_OFFSET 0x800000 6788 6789 #define BAR_ME_REGISTER 0x450000 6790 #define ME_REG_PF_NUM_SHIFT 0 6791 #define ME_REG_PF_NUM\ 6792 (7L<<ME_REG_PF_NUM_SHIFT) /* Relative PF Num */ 6793 #define ME_REG_VF_VALID (1<<8) 6794 #define ME_REG_VF_NUM_SHIFT 9 6795 #define ME_REG_VF_NUM_MASK (0x3f<<ME_REG_VF_NUM_SHIFT) 6796 #define ME_REG_VF_ERR (0x1<<3) 6797 #define ME_REG_ABS_PF_NUM_SHIFT 16 6798 #define ME_REG_ABS_PF_NUM\ 6799 (7L<<ME_REG_ABS_PF_NUM_SHIFT) /* Absolute PF Num */ 6800 6801 6802 #define PXP_VF_ADDR_IGU_START 0 6803 #define PXP_VF_ADDR_IGU_SIZE 0x3000 6804 #define PXP_VF_ADDR_IGU_END\ 6805 ((PXP_VF_ADDR_IGU_START) + (PXP_VF_ADDR_IGU_SIZE) - 1) 6806 6807 #define PXP_VF_ADDR_USDM_QUEUES_START 0x3000 6808 #define PXP_VF_ADDR_USDM_QUEUES_SIZE\ 6809 (PXP_VF_ADRR_NUM_QUEUES * PXP_ADDR_QUEUE_SIZE) 6810 #define PXP_VF_ADDR_USDM_QUEUES_END\ 6811 ((PXP_VF_ADDR_USDM_QUEUES_START) + (PXP_VF_ADDR_USDM_QUEUES_SIZE) - 1) 6812 6813 #define PXP_VF_ADDR_CSDM_GLOBAL_START 0x7600 6814 #define PXP_VF_ADDR_CSDM_GLOBAL_SIZE (PXP_ADDR_REG_SIZE) 6815 #define PXP_VF_ADDR_CSDM_GLOBAL_END\ 6816 ((PXP_VF_ADDR_CSDM_GLOBAL_START) + (PXP_VF_ADDR_CSDM_GLOBAL_SIZE) - 1) 6817 6818 #define PXP_VF_ADDR_DB_START 0x7c00 6819 #define PXP_VF_ADDR_DB_SIZE 0x200 6820 #define PXP_VF_ADDR_DB_END\ 6821 ((PXP_VF_ADDR_DB_START) + (PXP_VF_ADDR_DB_SIZE) - 1) 6822 6823 #define MDIO_REG_BANK_CL73_IEEEB0 0x0 6824 #define MDIO_CL73_IEEEB0_CL73_AN_CONTROL 0x0 6825 #define MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN 0x0200 6826 #define MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN 0x1000 6827 #define MDIO_CL73_IEEEB0_CL73_AN_CONTROL_MAIN_RST 0x8000 6828 6829 #define MDIO_REG_BANK_CL73_IEEEB1 0x10 6830 #define MDIO_CL73_IEEEB1_AN_ADV1 0x00 6831 #define MDIO_CL73_IEEEB1_AN_ADV1_PAUSE 0x0400 6832 #define MDIO_CL73_IEEEB1_AN_ADV1_ASYMMETRIC 0x0800 6833 #define MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_BOTH 0x0C00 6834 #define MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK 0x0C00 6835 #define MDIO_CL73_IEEEB1_AN_ADV2 0x01 6836 #define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M 0x0000 6837 #define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX 0x0020 6838 #define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4 0x0040 6839 #define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KR 0x0080 6840 #define MDIO_CL73_IEEEB1_AN_LP_ADV1 0x03 6841 #define MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE 0x0400 6842 #define MDIO_CL73_IEEEB1_AN_LP_ADV1_ASYMMETRIC 0x0800 6843 #define MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE_BOTH 0x0C00 6844 #define MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE_MASK 0x0C00 6845 #define MDIO_CL73_IEEEB1_AN_LP_ADV2 0x04 6846 6847 #define MDIO_REG_BANK_RX0 0x80b0 6848 #define MDIO_RX0_RX_STATUS 0x10 6849 #define MDIO_RX0_RX_STATUS_SIGDET 0x8000 6850 #define MDIO_RX0_RX_STATUS_RX_SEQ_DONE 0x1000 6851 #define MDIO_RX0_RX_EQ_BOOST 0x1c 6852 #define MDIO_RX0_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7 6853 #define MDIO_RX0_RX_EQ_BOOST_OFFSET_CTRL 0x10 6854 6855 #define MDIO_REG_BANK_RX1 0x80c0 6856 #define MDIO_RX1_RX_EQ_BOOST 0x1c 6857 #define MDIO_RX1_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7 6858 #define MDIO_RX1_RX_EQ_BOOST_OFFSET_CTRL 0x10 6859 6860 #define MDIO_REG_BANK_RX2 0x80d0 6861 #define MDIO_RX2_RX_EQ_BOOST 0x1c 6862 #define MDIO_RX2_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7 6863 #define MDIO_RX2_RX_EQ_BOOST_OFFSET_CTRL 0x10 6864 6865 #define MDIO_REG_BANK_RX3 0x80e0 6866 #define MDIO_RX3_RX_EQ_BOOST 0x1c 6867 #define MDIO_RX3_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7 6868 #define MDIO_RX3_RX_EQ_BOOST_OFFSET_CTRL 0x10 6869 6870 #define MDIO_REG_BANK_RX_ALL 0x80f0 6871 #define MDIO_RX_ALL_RX_EQ_BOOST 0x1c 6872 #define MDIO_RX_ALL_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7 6873 #define MDIO_RX_ALL_RX_EQ_BOOST_OFFSET_CTRL 0x10 6874 6875 #define MDIO_REG_BANK_TX0 0x8060 6876 #define MDIO_TX0_TX_DRIVER 0x17 6877 #define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000 6878 #define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12 6879 #define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00 6880 #define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8 6881 #define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0 6882 #define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4 6883 #define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e 6884 #define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1 6885 #define MDIO_TX0_TX_DRIVER_ICBUF1T 1 6886 6887 #define MDIO_REG_BANK_TX1 0x8070 6888 #define MDIO_TX1_TX_DRIVER 0x17 6889 #define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000 6890 #define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12 6891 #define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00 6892 #define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8 6893 #define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0 6894 #define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4 6895 #define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e 6896 #define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1 6897 #define MDIO_TX0_TX_DRIVER_ICBUF1T 1 6898 6899 #define MDIO_REG_BANK_TX2 0x8080 6900 #define MDIO_TX2_TX_DRIVER 0x17 6901 #define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000 6902 #define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12 6903 #define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00 6904 #define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8 6905 #define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0 6906 #define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4 6907 #define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e 6908 #define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1 6909 #define MDIO_TX0_TX_DRIVER_ICBUF1T 1 6910 6911 #define MDIO_REG_BANK_TX3 0x8090 6912 #define MDIO_TX3_TX_DRIVER 0x17 6913 #define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000 6914 #define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12 6915 #define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00 6916 #define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8 6917 #define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0 6918 #define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4 6919 #define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e 6920 #define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1 6921 #define MDIO_TX0_TX_DRIVER_ICBUF1T 1 6922 6923 #define MDIO_REG_BANK_XGXS_BLOCK0 0x8000 6924 #define MDIO_BLOCK0_XGXS_CONTROL 0x10 6925 6926 #define MDIO_REG_BANK_XGXS_BLOCK1 0x8010 6927 #define MDIO_BLOCK1_LANE_CTRL0 0x15 6928 #define MDIO_BLOCK1_LANE_CTRL1 0x16 6929 #define MDIO_BLOCK1_LANE_CTRL2 0x17 6930 #define MDIO_BLOCK1_LANE_PRBS 0x19 6931 6932 #define MDIO_REG_BANK_XGXS_BLOCK2 0x8100 6933 #define MDIO_XGXS_BLOCK2_RX_LN_SWAP 0x10 6934 #define MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE 0x8000 6935 #define MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE 0x4000 6936 #define MDIO_XGXS_BLOCK2_TX_LN_SWAP 0x11 6937 #define MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE 0x8000 6938 #define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G 0x14 6939 #define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS 0x0001 6940 #define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS 0x0010 6941 #define MDIO_XGXS_BLOCK2_TEST_MODE_LANE 0x15 6942 6943 #define MDIO_REG_BANK_GP_STATUS 0x8120 6944 #define MDIO_GP_STATUS_TOP_AN_STATUS1 0x1B 6945 #define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE 0x0001 6946 #define MDIO_GP_STATUS_TOP_AN_STATUS1_CL37_AUTONEG_COMPLETE 0x0002 6947 #define MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS 0x0004 6948 #define MDIO_GP_STATUS_TOP_AN_STATUS1_DUPLEX_STATUS 0x0008 6949 #define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE 0x0010 6950 #define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_LP_NP_BAM_ABLE 0x0020 6951 #define MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE 0x0040 6952 #define MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_RXSIDE 0x0080 6953 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_MASK 0x3f00 6954 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10M 0x0000 6955 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_100M 0x0100 6956 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G 0x0200 6957 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_2_5G 0x0300 6958 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_5G 0x0400 6959 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_6G 0x0500 6960 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_HIG 0x0600 6961 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_CX4 0x0700 6962 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12G_HIG 0x0800 6963 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12_5G 0x0900 6964 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_13G 0x0A00 6965 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_15G 0x0B00 6966 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_16G 0x0C00 6967 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX 0x0D00 6968 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4 0x0E00 6969 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KR 0x0F00 6970 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_XFI 0x1B00 6971 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_20G_DXGXS 0x1E00 6972 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_SFI 0x1F00 6973 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_20G_KR2 0x3900 6974 6975 6976 #define MDIO_REG_BANK_10G_PARALLEL_DETECT 0x8130 6977 #define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS 0x10 6978 #define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS_PD_LINK 0x8000 6979 #define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL 0x11 6980 #define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN 0x1 6981 #define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK 0x13 6982 #define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT (0xb71<<1) 6983 6984 #define MDIO_REG_BANK_SERDES_DIGITAL 0x8300 6985 #define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1 0x10 6986 #define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE 0x0001 6987 #define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_TBI_IF 0x0002 6988 #define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN 0x0004 6989 #define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT 0x0008 6990 #define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET 0x0010 6991 #define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE 0x0020 6992 #define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2 0x11 6993 #define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN 0x0001 6994 #define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_AN_FST_TMR 0x0040 6995 #define MDIO_SERDES_DIGITAL_A_1000X_STATUS1 0x14 6996 #define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SGMII 0x0001 6997 #define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_LINK 0x0002 6998 #define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_DUPLEX 0x0004 6999 #define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_MASK 0x0018 7000 #define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_SHIFT 3 7001 #define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_2_5G 0x0018 7002 #define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_1G 0x0010 7003 #define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_100M 0x0008 7004 #define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_10M 0x0000 7005 #define MDIO_SERDES_DIGITAL_A_1000X_STATUS2 0x15 7006 #define MDIO_SERDES_DIGITAL_A_1000X_STATUS2_AN_DISABLED 0x0002 7007 #define MDIO_SERDES_DIGITAL_MISC1 0x18 7008 #define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_MASK 0xE000 7009 #define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_25M 0x0000 7010 #define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_100M 0x2000 7011 #define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_125M 0x4000 7012 #define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M 0x6000 7013 #define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_187_5M 0x8000 7014 #define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL 0x0010 7015 #define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK 0x000f 7016 #define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_2_5G 0x0000 7017 #define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_5G 0x0001 7018 #define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_6G 0x0002 7019 #define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_HIG 0x0003 7020 #define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4 0x0004 7021 #define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_12G 0x0005 7022 #define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_12_5G 0x0006 7023 #define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G 0x0007 7024 #define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_15G 0x0008 7025 #define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_16G 0x0009 7026 7027 #define MDIO_REG_BANK_OVER_1G 0x8320 7028 #define MDIO_OVER_1G_DIGCTL_3_4 0x14 7029 #define MDIO_OVER_1G_DIGCTL_3_4_MP_ID_MASK 0xffe0 7030 #define MDIO_OVER_1G_DIGCTL_3_4_MP_ID_SHIFT 5 7031 #define MDIO_OVER_1G_UP1 0x19 7032 #define MDIO_OVER_1G_UP1_2_5G 0x0001 7033 #define MDIO_OVER_1G_UP1_5G 0x0002 7034 #define MDIO_OVER_1G_UP1_6G 0x0004 7035 #define MDIO_OVER_1G_UP1_10G 0x0010 7036 #define MDIO_OVER_1G_UP1_10GH 0x0008 7037 #define MDIO_OVER_1G_UP1_12G 0x0020 7038 #define MDIO_OVER_1G_UP1_12_5G 0x0040 7039 #define MDIO_OVER_1G_UP1_13G 0x0080 7040 #define MDIO_OVER_1G_UP1_15G 0x0100 7041 #define MDIO_OVER_1G_UP1_16G 0x0200 7042 #define MDIO_OVER_1G_UP2 0x1A 7043 #define MDIO_OVER_1G_UP2_IPREDRIVER_MASK 0x0007 7044 #define MDIO_OVER_1G_UP2_IDRIVER_MASK 0x0038 7045 #define MDIO_OVER_1G_UP2_PREEMPHASIS_MASK 0x03C0 7046 #define MDIO_OVER_1G_UP3 0x1B 7047 #define MDIO_OVER_1G_UP3_HIGIG2 0x0001 7048 #define MDIO_OVER_1G_LP_UP1 0x1C 7049 #define MDIO_OVER_1G_LP_UP2 0x1D 7050 #define MDIO_OVER_1G_LP_UP2_MR_ADV_OVER_1G_MASK 0x03ff 7051 #define MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK 0x0780 7052 #define MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT 7 7053 #define MDIO_OVER_1G_LP_UP3 0x1E 7054 7055 #define MDIO_REG_BANK_REMOTE_PHY 0x8330 7056 #define MDIO_REMOTE_PHY_MISC_RX_STATUS 0x10 7057 #define MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG 0x0010 7058 #define MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG 0x0600 7059 7060 #define MDIO_REG_BANK_BAM_NEXT_PAGE 0x8350 7061 #define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL 0x10 7062 #define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE 0x0001 7063 #define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN 0x0002 7064 7065 #define MDIO_REG_BANK_CL73_USERB0 0x8370 7066 #define MDIO_CL73_USERB0_CL73_UCTRL 0x10 7067 #define MDIO_CL73_USERB0_CL73_UCTRL_USTAT1_MUXSEL 0x0002 7068 #define MDIO_CL73_USERB0_CL73_USTAT1 0x11 7069 #define MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK 0x0100 7070 #define MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37 0x0400 7071 #define MDIO_CL73_USERB0_CL73_BAM_CTRL1 0x12 7072 #define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN 0x8000 7073 #define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN 0x4000 7074 #define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN 0x2000 7075 #define MDIO_CL73_USERB0_CL73_BAM_CTRL3 0x14 7076 #define MDIO_CL73_USERB0_CL73_BAM_CTRL3_USE_CL73_HCD_MR 0x0001 7077 7078 #define MDIO_REG_BANK_AER_BLOCK 0xFFD0 7079 #define MDIO_AER_BLOCK_AER_REG 0x1E 7080 7081 #define MDIO_REG_BANK_COMBO_IEEE0 0xFFE0 7082 #define MDIO_COMBO_IEEE0_MII_CONTROL 0x10 7083 #define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK 0x2040 7084 #define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_10 0x0000 7085 #define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100 0x2000 7086 #define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000 0x0040 7087 #define MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX 0x0100 7088 #define MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN 0x0200 7089 #define MDIO_COMBO_IEEO_MII_CONTROL_AN_EN 0x1000 7090 #define MDIO_COMBO_IEEO_MII_CONTROL_LOOPBACK 0x4000 7091 #define MDIO_COMBO_IEEO_MII_CONTROL_RESET 0x8000 7092 #define MDIO_COMBO_IEEE0_MII_STATUS 0x11 7093 #define MDIO_COMBO_IEEE0_MII_STATUS_LINK_PASS 0x0004 7094 #define MDIO_COMBO_IEEE0_MII_STATUS_AUTONEG_COMPLETE 0x0020 7095 #define MDIO_COMBO_IEEE0_AUTO_NEG_ADV 0x14 7096 #define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX 0x0020 7097 #define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_HALF_DUPLEX 0x0040 7098 #define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK 0x0180 7099 #define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE 0x0000 7100 #define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC 0x0080 7101 #define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC 0x0100 7102 #define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH 0x0180 7103 #define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_NEXT_PAGE 0x8000 7104 #define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1 0x15 7105 #define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_NEXT_PAGE 0x8000 7106 #define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_ACK 0x4000 7107 #define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_MASK 0x0180 7108 #define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_NONE 0x0000 7109 #define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_BOTH 0x0180 7110 #define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_HALF_DUP_CAP 0x0040 7111 #define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_FULL_DUP_CAP 0x0020 7112 /*WhenthelinkpartnerisinSGMIImode(bit0=1),then 7113 bit15=link,bit12=duplex,bits11:10=speed,bit14=acknowledge. 7114 Theotherbitsarereservedandshouldbezero*/ 7115 #define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_SGMII_MODE 0x0001 7116 7117 7118 #define MDIO_PMA_DEVAD 0x1 7119 /*ieee*/ 7120 #define MDIO_PMA_REG_CTRL 0x0 7121 #define MDIO_PMA_REG_STATUS 0x1 7122 #define MDIO_PMA_REG_10G_CTRL2 0x7 7123 #define MDIO_PMA_REG_TX_DISABLE 0x0009 7124 #define MDIO_PMA_REG_RX_SD 0xa 7125 /*bcm*/ 7126 #define MDIO_PMA_REG_BCM_CTRL 0x0096 7127 #define MDIO_PMA_REG_FEC_CTRL 0x00ab 7128 #define MDIO_PMA_REG_PHY_IDENTIFIER 0xc800 7129 #define MDIO_PMA_REG_DIGITAL_CTRL 0xc808 7130 #define MDIO_PMA_REG_DIGITAL_STATUS 0xc809 7131 #define MDIO_PMA_REG_TX_POWER_DOWN 0xca02 7132 #define MDIO_PMA_REG_CMU_PLL_BYPASS 0xca09 7133 #define MDIO_PMA_REG_MISC_CTRL 0xca0a 7134 #define MDIO_PMA_REG_GEN_CTRL 0xca10 7135 #define MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP 0x0188 7136 #define MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET 0x018a 7137 #define MDIO_PMA_REG_M8051_MSGIN_REG 0xca12 7138 #define MDIO_PMA_REG_M8051_MSGOUT_REG 0xca13 7139 #define MDIO_PMA_REG_ROM_VER1 0xca19 7140 #define MDIO_PMA_REG_ROM_VER2 0xca1a 7141 #define MDIO_PMA_REG_EDC_FFE_MAIN 0xca1b 7142 #define MDIO_PMA_REG_PLL_BANDWIDTH 0xca1d 7143 #define MDIO_PMA_REG_PLL_CTRL 0xca1e 7144 #define MDIO_PMA_REG_MISC_CTRL0 0xca23 7145 #define MDIO_PMA_REG_LRM_MODE 0xca3f 7146 #define MDIO_PMA_REG_CDR_BANDWIDTH 0xca46 7147 #define MDIO_PMA_REG_MISC_CTRL1 0xca85 7148 7149 #define MDIO_PMA_REG_SFP_TWO_WIRE_CTRL 0x8000 7150 #define MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK 0x000c 7151 #define MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE 0x0000 7152 #define MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE 0x0004 7153 #define MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IN_PROGRESS 0x0008 7154 #define MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_FAILED 0x000c 7155 #define MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT 0x8002 7156 #define MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR 0x8003 7157 #define MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF 0xc820 7158 #define MDIO_PMA_REG_8726_TWO_WIRE_DATA_MASK 0xff 7159 #define MDIO_PMA_REG_8726_TX_CTRL1 0xca01 7160 #define MDIO_PMA_REG_8726_TX_CTRL2 0xca05 7161 7162 #define MDIO_PMA_REG_8727_TWO_WIRE_SLAVE_ADDR 0x8005 7163 #define MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF 0x8007 7164 #define MDIO_PMA_REG_8727_TWO_WIRE_DATA_MASK 0xff 7165 #define MDIO_PMA_REG_8727_TX_CTRL1 0xca02 7166 #define MDIO_PMA_REG_8727_TX_CTRL2 0xca05 7167 #define MDIO_PMA_REG_8727_PCS_OPT_CTRL 0xc808 7168 #define MDIO_PMA_REG_8727_GPIO_CTRL 0xc80e 7169 #define MDIO_PMA_REG_8727_PCS_GP 0xc842 7170 #define MDIO_PMA_REG_8727_OPT_CFG_REG 0xc8e4 7171 7172 #define MDIO_AN_REG_8727_MISC_CTRL 0x8309 7173 7174 #define MDIO_PMA_REG_8073_CHIP_REV 0xc801 7175 #define MDIO_PMA_REG_8073_SPEED_LINK_STATUS 0xc820 7176 #define MDIO_PMA_REG_8073_XAUI_WA 0xc841 7177 #define MDIO_PMA_REG_8073_OPT_DIGITAL_CTRL 0xcd08 7178 7179 #define MDIO_PMA_REG_7101_RESET 0xc000 7180 #define MDIO_PMA_REG_7107_LED_CNTL 0xc007 7181 #define MDIO_PMA_REG_7107_LINK_LED_CNTL 0xc009 7182 #define MDIO_PMA_REG_7101_VER1 0xc026 7183 #define MDIO_PMA_REG_7101_VER2 0xc027 7184 7185 #define MDIO_PMA_REG_8481_PMD_SIGNAL 0xa811 7186 #define MDIO_PMA_REG_8481_LED1_MASK 0xa82c 7187 #define MDIO_PMA_REG_8481_LED2_MASK 0xa82f 7188 #define MDIO_PMA_REG_8481_LED3_MASK 0xa832 7189 #define MDIO_PMA_REG_8481_LED3_BLINK 0xa834 7190 #define MDIO_PMA_REG_8481_LED5_MASK 0xa838 7191 #define MDIO_PMA_REG_8481_SIGNAL_MASK 0xa835 7192 #define MDIO_PMA_REG_8481_LINK_SIGNAL 0xa83b 7193 #define MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_MASK 0x800 7194 #define MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_SHIFT 11 7195 7196 7197 #define MDIO_WIS_DEVAD 0x2 7198 /*bcm*/ 7199 #define MDIO_WIS_REG_LASI_CNTL 0x9002 7200 #define MDIO_WIS_REG_LASI_STATUS 0x9005 7201 7202 #define MDIO_PCS_DEVAD 0x3 7203 #define MDIO_PCS_REG_STATUS 0x0020 7204 #define MDIO_PCS_REG_LASI_STATUS 0x9005 7205 #define MDIO_PCS_REG_7101_DSP_ACCESS 0xD000 7206 #define MDIO_PCS_REG_7101_SPI_MUX 0xD008 7207 #define MDIO_PCS_REG_7101_SPI_CTRL_ADDR 0xE12A 7208 #define MDIO_PCS_REG_7101_SPI_RESET_BIT (5) 7209 #define MDIO_PCS_REG_7101_SPI_FIFO_ADDR 0xE02A 7210 #define MDIO_PCS_REG_7101_SPI_FIFO_ADDR_WRITE_ENABLE_CMD (6) 7211 #define MDIO_PCS_REG_7101_SPI_FIFO_ADDR_BULK_ERASE_CMD (0xC7) 7212 #define MDIO_PCS_REG_7101_SPI_FIFO_ADDR_PAGE_PROGRAM_CMD (2) 7213 #define MDIO_PCS_REG_7101_SPI_BYTES_TO_TRANSFER_ADDR 0xE028 7214 7215 7216 #define MDIO_XS_DEVAD 0x4 7217 #define MDIO_XS_PLL_SEQUENCER 0x8000 7218 #define MDIO_XS_SFX7101_XGXS_TEST1 0xc00a 7219 7220 #define MDIO_XS_8706_REG_BANK_RX0 0x80bc 7221 #define MDIO_XS_8706_REG_BANK_RX1 0x80cc 7222 #define MDIO_XS_8706_REG_BANK_RX2 0x80dc 7223 #define MDIO_XS_8706_REG_BANK_RX3 0x80ec 7224 #define MDIO_XS_8706_REG_BANK_RXA 0x80fc 7225 7226 #define MDIO_XS_REG_8073_RX_CTRL_PCIE 0x80FA 7227 7228 #define MDIO_AN_DEVAD 0x7 7229 /*ieee*/ 7230 #define MDIO_AN_REG_CTRL 0x0000 7231 #define MDIO_AN_REG_STATUS 0x0001 7232 #define MDIO_AN_REG_STATUS_AN_COMPLETE 0x0020 7233 #define MDIO_AN_REG_ADV_PAUSE 0x0010 7234 #define MDIO_AN_REG_ADV_PAUSE_PAUSE 0x0400 7235 #define MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC 0x0800 7236 #define MDIO_AN_REG_ADV_PAUSE_BOTH 0x0C00 7237 #define MDIO_AN_REG_ADV_PAUSE_MASK 0x0C00 7238 #define MDIO_AN_REG_ADV 0x0011 7239 #define MDIO_AN_REG_ADV2 0x0012 7240 #define MDIO_AN_REG_LP_AUTO_NEG 0x0013 7241 #define MDIO_AN_REG_LP_AUTO_NEG2 0x0014 7242 #define MDIO_AN_REG_MASTER_STATUS 0x0021 7243 #define MDIO_AN_REG_EEE_ADV 0x003c 7244 #define MDIO_AN_REG_LP_EEE_ADV 0x003d 7245 /*bcm*/ 7246 #define MDIO_AN_REG_LINK_STATUS 0x8304 7247 #define MDIO_AN_REG_CL37_CL73 0x8370 7248 #define MDIO_AN_REG_CL37_AN 0xffe0 7249 #define MDIO_AN_REG_CL37_FC_LD 0xffe4 7250 #define MDIO_AN_REG_CL37_FC_LP 0xffe5 7251 #define MDIO_AN_REG_1000T_STATUS 0xffea 7252 7253 #define MDIO_AN_REG_8073_2_5G 0x8329 7254 #define MDIO_AN_REG_8073_BAM 0x8350 7255 7256 #define MDIO_AN_REG_8481_10GBASE_T_AN_CTRL 0x0020 7257 #define MDIO_AN_REG_8481_LEGACY_MII_CTRL 0xffe0 7258 #define MDIO_AN_REG_8481_MII_CTRL_FORCE_1G 0x40 7259 #define MDIO_AN_REG_8481_LEGACY_MII_STATUS 0xffe1 7260 #define MDIO_AN_REG_848xx_ID_MSB 0xffe2 7261 #define BCM84858_PHY_ID 0x600d 7262 #define MDIO_AN_REG_848xx_ID_LSB 0xffe3 7263 #define MDIO_AN_REG_8481_LEGACY_AN_ADV 0xffe4 7264 #define MDIO_AN_REG_8481_LEGACY_AN_EXPANSION 0xffe6 7265 #define MDIO_AN_REG_8481_1000T_CTRL 0xffe9 7266 #define MDIO_AN_REG_8481_1G_100T_EXT_CTRL 0xfff0 7267 #define MIDO_AN_REG_8481_EXT_CTRL_FORCE_LEDS_OFF 0x0008 7268 #define MDIO_AN_REG_8481_EXPANSION_REG_RD_RW 0xfff5 7269 #define MDIO_AN_REG_8481_EXPANSION_REG_ACCESS 0xfff7 7270 #define MDIO_AN_REG_8481_AUX_CTRL 0xfff8 7271 #define MDIO_AN_REG_8481_LEGACY_SHADOW 0xfffc 7272 7273 /* BCM84823 only */ 7274 #define MDIO_CTL_DEVAD 0x1e 7275 #define MDIO_CTL_REG_84823_MEDIA 0x401a 7276 #define MDIO_CTL_REG_84823_MEDIA_MAC_MASK 0x0018 7277 /* These pins configure the BCM84823 interface to MAC after reset. */ 7278 #define MDIO_CTL_REG_84823_CTRL_MAC_XFI 0x0008 7279 #define MDIO_CTL_REG_84823_MEDIA_MAC_XAUI_M 0x0010 7280 /* These pins configure the BCM84823 interface to Line after reset. */ 7281 #define MDIO_CTL_REG_84823_MEDIA_LINE_MASK 0x0060 7282 #define MDIO_CTL_REG_84823_MEDIA_LINE_XAUI_L 0x0020 7283 #define MDIO_CTL_REG_84823_MEDIA_LINE_XFI 0x0040 7284 /* When this pin is active high during reset, 10GBASE-T core is power 7285 * down, When it is active low the 10GBASE-T is power up 7286 */ 7287 #define MDIO_CTL_REG_84823_MEDIA_COPPER_CORE_DOWN 0x0080 7288 #define MDIO_CTL_REG_84823_MEDIA_PRIORITY_MASK 0x0100 7289 #define MDIO_CTL_REG_84823_MEDIA_PRIORITY_COPPER 0x0000 7290 #define MDIO_CTL_REG_84823_MEDIA_PRIORITY_FIBER 0x0100 7291 #define MDIO_CTL_REG_84823_MEDIA_FIBER_1G 0x1000 7292 #define MDIO_CTL_REG_84823_USER_CTRL_REG 0x4005 7293 #define MDIO_CTL_REG_84823_USER_CTRL_CMS 0x0080 7294 #define MDIO_PMA_REG_84823_CTL_SLOW_CLK_CNT_HIGH 0xa82b 7295 #define MDIO_PMA_REG_84823_BLINK_RATE_VAL_15P9HZ 0x2f 7296 #define MDIO_PMA_REG_84823_CTL_LED_CTL_1 0xa8e3 7297 #define MDIO_PMA_REG_84833_CTL_LED_CTL_1 0xa8ec 7298 #define MDIO_PMA_REG_84823_LED3_STRETCH_EN 0x0080 7299 /* BCM84858 only */ 7300 #define MDIO_PMA_REG_84858_ALLOW_GPHY_ACT 0x8000 7301 7302 /* BCM84833 only */ 7303 #define MDIO_84833_TOP_CFG_FW_REV 0x400f 7304 #define MDIO_84833_TOP_CFG_FW_EEE 0x10b1 7305 #define MDIO_84833_TOP_CFG_FW_NO_EEE 0x1f81 7306 #define MDIO_84833_TOP_CFG_XGPHY_STRAP1 0x401a 7307 #define MDIO_84833_SUPER_ISOLATE 0x8000 7308 /* These are mailbox register set used by 84833/84858. */ 7309 #define MDIO_848xx_TOP_CFG_SCRATCH_REG0 0x4005 7310 #define MDIO_848xx_TOP_CFG_SCRATCH_REG1 0x4006 7311 #define MDIO_848xx_TOP_CFG_SCRATCH_REG2 0x4007 7312 #define MDIO_848xx_TOP_CFG_SCRATCH_REG3 0x4008 7313 #define MDIO_848xx_TOP_CFG_SCRATCH_REG4 0x4009 7314 #define MDIO_848xx_TOP_CFG_SCRATCH_REG26 0x4037 7315 #define MDIO_848xx_TOP_CFG_SCRATCH_REG27 0x4038 7316 #define MDIO_848xx_TOP_CFG_SCRATCH_REG28 0x4039 7317 #define MDIO_848xx_TOP_CFG_SCRATCH_REG29 0x403a 7318 #define MDIO_848xx_TOP_CFG_SCRATCH_REG30 0x403b 7319 #define MDIO_848xx_TOP_CFG_SCRATCH_REG31 0x403c 7320 #define MDIO_848xx_CMD_HDLR_COMMAND (MDIO_848xx_TOP_CFG_SCRATCH_REG0) 7321 #define MDIO_848xx_CMD_HDLR_STATUS (MDIO_848xx_TOP_CFG_SCRATCH_REG26) 7322 #define MDIO_848xx_CMD_HDLR_DATA1 (MDIO_848xx_TOP_CFG_SCRATCH_REG27) 7323 #define MDIO_848xx_CMD_HDLR_DATA2 (MDIO_848xx_TOP_CFG_SCRATCH_REG28) 7324 #define MDIO_848xx_CMD_HDLR_DATA3 (MDIO_848xx_TOP_CFG_SCRATCH_REG29) 7325 #define MDIO_848xx_CMD_HDLR_DATA4 (MDIO_848xx_TOP_CFG_SCRATCH_REG30) 7326 #define MDIO_848xx_CMD_HDLR_DATA5 (MDIO_848xx_TOP_CFG_SCRATCH_REG31) 7327 7328 /* Mailbox command set used by 84833/84858 */ 7329 #define PHY848xx_CMD_SET_PAIR_SWAP 0x8001 7330 #define PHY848xx_CMD_GET_EEE_MODE 0x8008 7331 #define PHY848xx_CMD_SET_EEE_MODE 0x8009 7332 /* Mailbox status set used by 84833 only */ 7333 #define PHY84833_STATUS_CMD_RECEIVED 0x0001 7334 #define PHY84833_STATUS_CMD_IN_PROGRESS 0x0002 7335 #define PHY84833_STATUS_CMD_COMPLETE_PASS 0x0004 7336 #define PHY84833_STATUS_CMD_COMPLETE_ERROR 0x0008 7337 #define PHY84833_STATUS_CMD_OPEN_FOR_CMDS 0x0010 7338 #define PHY84833_STATUS_CMD_SYSTEM_BOOT 0x0020 7339 #define PHY84833_STATUS_CMD_NOT_OPEN_FOR_CMDS 0x0040 7340 #define PHY84833_STATUS_CMD_CLEAR_COMPLETE 0x0080 7341 #define PHY84833_STATUS_CMD_OPEN_OVERRIDE 0xa5a5 7342 /* Mailbox Process */ 7343 #define PHY84833_MB_PROCESS1 1 7344 #define PHY84833_MB_PROCESS2 2 7345 #define PHY84833_MB_PROCESS3 3 7346 7347 /* Mailbox status set used by 84858 only */ 7348 #define PHY84858_STATUS_CMD_RECEIVED 0x0001 7349 #define PHY84858_STATUS_CMD_IN_PROGRESS 0x0002 7350 #define PHY84858_STATUS_CMD_COMPLETE_PASS 0x0004 7351 #define PHY84858_STATUS_CMD_COMPLETE_ERROR 0x0008 7352 #define PHY84858_STATUS_CMD_SYSTEM_BUSY 0xbbbb 7353 7354 7355 /* Warpcore clause 45 addressing */ 7356 #define MDIO_WC_DEVAD 0x3 7357 #define MDIO_WC_REG_IEEE0BLK_MIICNTL 0x0 7358 #define MDIO_WC_REG_IEEE0BLK_AUTONEGNP 0x7 7359 #define MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT0 0x10 7360 #define MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT1 0x11 7361 #define MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT2 0x12 7362 #define MDIO_WC_REG_AN_IEEE1BLK_AN_ADV2_FEC_ABILITY 0x4000 7363 #define MDIO_WC_REG_AN_IEEE1BLK_AN_ADV2_FEC_REQ 0x8000 7364 #define MDIO_WC_REG_PCS_STATUS2 0x0021 7365 #define MDIO_WC_REG_PMD_KR_CONTROL 0x0096 7366 #define MDIO_WC_REG_XGXSBLK0_XGXSCONTROL 0x8000 7367 #define MDIO_WC_REG_XGXSBLK0_MISCCONTROL1 0x800e 7368 #define MDIO_WC_REG_XGXSBLK1_DESKEW 0x8010 7369 #define MDIO_WC_REG_XGXSBLK1_LANECTRL0 0x8015 7370 #define MDIO_WC_REG_XGXSBLK1_LANECTRL1 0x8016 7371 #define MDIO_WC_REG_XGXSBLK1_LANECTRL2 0x8017 7372 #define MDIO_WC_REG_TX0_ANA_CTRL0 0x8061 7373 #define MDIO_WC_REG_TX1_ANA_CTRL0 0x8071 7374 #define MDIO_WC_REG_TX2_ANA_CTRL0 0x8081 7375 #define MDIO_WC_REG_TX3_ANA_CTRL0 0x8091 7376 #define MDIO_WC_REG_TX0_TX_DRIVER 0x8067 7377 #define MDIO_WC_REG_TX0_TX_DRIVER_IFIR_OFFSET 0x01 7378 #define MDIO_WC_REG_TX0_TX_DRIVER_IFIR_MASK 0x000e 7379 #define MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_OFFSET 0x04 7380 #define MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_MASK 0x00f0 7381 #define MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_OFFSET 0x08 7382 #define MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00 7383 #define MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_OFFSET 0x0c 7384 #define MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_MASK 0x7000 7385 #define MDIO_WC_REG_TX1_TX_DRIVER 0x8077 7386 #define MDIO_WC_REG_TX2_TX_DRIVER 0x8087 7387 #define MDIO_WC_REG_TX3_TX_DRIVER 0x8097 7388 #define MDIO_WC_REG_RX0_ANARXCONTROL1G 0x80b9 7389 #define MDIO_WC_REG_RX2_ANARXCONTROL1G 0x80d9 7390 #define MDIO_WC_REG_RX0_PCI_CTRL 0x80ba 7391 #define MDIO_WC_REG_RX1_PCI_CTRL 0x80ca 7392 #define MDIO_WC_REG_RX2_PCI_CTRL 0x80da 7393 #define MDIO_WC_REG_RX3_PCI_CTRL 0x80ea 7394 #define MDIO_WC_REG_RXB_ANA_RX_CONTROL_PCI 0x80fa 7395 #define MDIO_WC_REG_XGXSBLK2_UNICORE_MODE_10G 0x8104 7396 #define MDIO_WC_REG_XGXS_STATUS3 0x8129 7397 #define MDIO_WC_REG_PAR_DET_10G_STATUS 0x8130 7398 #define MDIO_WC_REG_PAR_DET_10G_CTRL 0x8131 7399 #define MDIO_WC_REG_XGXS_X2_CONTROL2 0x8141 7400 #define MDIO_WC_REG_XGXS_X2_CONTROL3 0x8142 7401 #define MDIO_WC_REG_XGXS_RX_LN_SWAP1 0x816B 7402 #define MDIO_WC_REG_XGXS_TX_LN_SWAP1 0x8169 7403 #define MDIO_WC_REG_GP2_STATUS_GP_2_0 0x81d0 7404 #define MDIO_WC_REG_GP2_STATUS_GP_2_1 0x81d1 7405 #define MDIO_WC_REG_GP2_STATUS_GP_2_2 0x81d2 7406 #define MDIO_WC_REG_GP2_STATUS_GP_2_3 0x81d3 7407 #define MDIO_WC_REG_GP2_STATUS_GP_2_4 0x81d4 7408 #define MDIO_WC_REG_GP2_STATUS_GP_2_4_CL73_AN_CMPL 0x1000 7409 #define MDIO_WC_REG_GP2_STATUS_GP_2_4_CL37_AN_CMPL 0x0100 7410 #define MDIO_WC_REG_GP2_STATUS_GP_2_4_CL37_LP_AN_CAP 0x0010 7411 #define MDIO_WC_REG_GP2_STATUS_GP_2_4_CL37_AN_CAP 0x1 7412 #define MDIO_WC_REG_UC_INFO_B0_DEAD_TRAP 0x81EE 7413 #define MDIO_WC_REG_UC_INFO_B1_VERSION 0x81F0 7414 #define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE 0x81F2 7415 #define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_LANE0_OFFSET 0x0 7416 #define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_DEFAULT 0x0 7417 #define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_SFP_OPT_LR 0x1 7418 #define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_SFP_DAC 0x2 7419 #define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_SFP_XLAUI 0x3 7420 #define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_LONG_CH_6G 0x4 7421 #define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_LANE1_OFFSET 0x4 7422 #define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_LANE2_OFFSET 0x8 7423 #define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_LANE3_OFFSET 0xc 7424 #define MDIO_WC_REG_UC_INFO_B1_CRC 0x81FE 7425 #define MDIO_WC_REG_DSC_SMC 0x8213 7426 #define MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0 0x821e 7427 #define MDIO_WC_REG_TX_FIR_TAP 0x82e2 7428 #define MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_OFFSET 0x00 7429 #define MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_MASK 0x000f 7430 #define MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_OFFSET 0x04 7431 #define MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_MASK 0x03f0 7432 #define MDIO_WC_REG_TX_FIR_TAP_POST_TAP_OFFSET 0x0a 7433 #define MDIO_WC_REG_TX_FIR_TAP_POST_TAP_MASK 0x7c00 7434 #define MDIO_WC_REG_TX_FIR_TAP_ENABLE 0x8000 7435 #define MDIO_WC_REG_CL72_USERB0_CL72_TX_FIR_TAP 0x82e2 7436 #define MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL 0x82e3 7437 #define MDIO_WC_REG_CL72_USERB0_CL72_OS_DEF_CTRL 0x82e6 7438 #define MDIO_WC_REG_CL72_USERB0_CL72_BR_DEF_CTRL 0x82e7 7439 #define MDIO_WC_REG_CL72_USERB0_CL72_2P5_DEF_CTRL 0x82e8 7440 #define MDIO_WC_REG_CL72_USERB0_CL72_MISC4_CONTROL 0x82ec 7441 #define MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1 0x8300 7442 #define MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2 0x8301 7443 #define MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3 0x8302 7444 #define MDIO_WC_REG_SERDESDIGITAL_STATUS1000X1 0x8304 7445 #define MDIO_WC_REG_SERDESDIGITAL_MISC1 0x8308 7446 #define MDIO_WC_REG_SERDESDIGITAL_MISC2 0x8309 7447 #define MDIO_WC_REG_DIGITAL3_UP1 0x8329 7448 #define MDIO_WC_REG_DIGITAL3_LP_UP1 0x832c 7449 #define MDIO_WC_REG_DIGITAL4_MISC3 0x833c 7450 #define MDIO_WC_REG_DIGITAL4_MISC5 0x833e 7451 #define MDIO_WC_REG_DIGITAL5_MISC6 0x8345 7452 #define MDIO_WC_REG_DIGITAL5_MISC7 0x8349 7453 #define MDIO_WC_REG_DIGITAL5_LINK_STATUS 0x834d 7454 #define MDIO_WC_REG_DIGITAL5_ACTUAL_SPEED 0x834e 7455 #define MDIO_WC_REG_DIGITAL6_MP5_NEXTPAGECTRL 0x8350 7456 #define MDIO_WC_REG_CL49_USERB0_CTRL 0x8368 7457 #define MDIO_WC_REG_CL73_USERB0_CTRL 0x8370 7458 #define MDIO_WC_REG_CL73_USERB0_USTAT 0x8371 7459 #define MDIO_WC_REG_CL73_BAM_CTRL1 0x8372 7460 #define MDIO_WC_REG_CL73_BAM_CTRL2 0x8373 7461 #define MDIO_WC_REG_CL73_BAM_CTRL3 0x8374 7462 #define MDIO_WC_REG_CL73_BAM_CODE_FIELD 0x837b 7463 #define MDIO_WC_REG_EEE_COMBO_CONTROL0 0x8390 7464 #define MDIO_WC_REG_TX66_CONTROL 0x83b0 7465 #define MDIO_WC_REG_RX66_CONTROL 0x83c0 7466 #define MDIO_WC_REG_RX66_SCW0 0x83c2 7467 #define MDIO_WC_REG_RX66_SCW1 0x83c3 7468 #define MDIO_WC_REG_RX66_SCW2 0x83c4 7469 #define MDIO_WC_REG_RX66_SCW3 0x83c5 7470 #define MDIO_WC_REG_RX66_SCW0_MASK 0x83c6 7471 #define MDIO_WC_REG_RX66_SCW1_MASK 0x83c7 7472 #define MDIO_WC_REG_RX66_SCW2_MASK 0x83c8 7473 #define MDIO_WC_REG_RX66_SCW3_MASK 0x83c9 7474 #define MDIO_WC_REG_FX100_CTRL1 0x8400 7475 #define MDIO_WC_REG_FX100_CTRL3 0x8402 7476 #define MDIO_WC_REG_CL82_USERB1_TX_CTRL5 0x8436 7477 #define MDIO_WC_REG_CL82_USERB1_TX_CTRL6 0x8437 7478 #define MDIO_WC_REG_CL82_USERB1_TX_CTRL7 0x8438 7479 #define MDIO_WC_REG_CL82_USERB1_TX_CTRL9 0x8439 7480 #define MDIO_WC_REG_CL82_USERB1_RX_CTRL10 0x843a 7481 #define MDIO_WC_REG_CL82_USERB1_RX_CTRL11 0x843b 7482 #define MDIO_WC_REG_ETA_CL73_OUI1 0x8453 7483 #define MDIO_WC_REG_ETA_CL73_OUI2 0x8454 7484 #define MDIO_WC_REG_ETA_CL73_OUI3 0x8455 7485 #define MDIO_WC_REG_ETA_CL73_LD_BAM_CODE 0x8456 7486 #define MDIO_WC_REG_ETA_CL73_LD_UD_CODE 0x8457 7487 #define MDIO_WC_REG_MICROBLK_CMD 0xffc2 7488 #define MDIO_WC_REG_MICROBLK_DL_STATUS 0xffc5 7489 #define MDIO_WC_REG_MICROBLK_CMD3 0xffcc 7490 7491 #define MDIO_WC_REG_AERBLK_AER 0xffde 7492 #define MDIO_WC_REG_COMBO_IEEE0_MIICTRL 0xffe0 7493 #define MDIO_WC_REG_COMBO_IEEE0_MIIISTAT 0xffe1 7494 7495 #define MDIO_WC0_XGXS_BLK2_LANE_RESET 0x810A 7496 #define MDIO_WC0_XGXS_BLK2_LANE_RESET_RX_BITSHIFT 0 7497 #define MDIO_WC0_XGXS_BLK2_LANE_RESET_TX_BITSHIFT 4 7498 7499 #define MDIO_WC0_XGXS_BLK6_XGXS_X2_CONTROL2 0x8141 7500 7501 #define DIGITAL5_ACTUAL_SPEED_TX_MASK 0x003f 7502 7503 /* 54618se */ 7504 #define MDIO_REG_GPHY_PHYID_LSB 0x3 7505 #define MDIO_REG_GPHY_ID_54618SE 0x5cd5 7506 #define MDIO_REG_GPHY_CL45_ADDR_REG 0xd 7507 #define MDIO_REG_GPHY_CL45_DATA_REG 0xe 7508 #define MDIO_REG_GPHY_EEE_RESOLVED 0x803e 7509 #define MDIO_REG_GPHY_EXP_ACCESS_GATE 0x15 7510 #define MDIO_REG_GPHY_EXP_ACCESS 0x17 7511 #define MDIO_REG_GPHY_EXP_ACCESS_TOP 0xd00 7512 #define MDIO_REG_GPHY_EXP_TOP_2K_BUF 0x40 7513 #define MDIO_REG_GPHY_AUX_STATUS 0x19 7514 #define MDIO_REG_INTR_STATUS 0x1a 7515 #define MDIO_REG_INTR_MASK 0x1b 7516 #define MDIO_REG_INTR_MASK_LINK_STATUS (0x1 << 1) 7517 #define MDIO_REG_GPHY_SHADOW 0x1c 7518 #define MDIO_REG_GPHY_SHADOW_LED_SEL1 (0x0d << 10) 7519 #define MDIO_REG_GPHY_SHADOW_LED_SEL2 (0x0e << 10) 7520 #define MDIO_REG_GPHY_SHADOW_WR_ENA (0x1 << 15) 7521 #define MDIO_REG_GPHY_SHADOW_AUTO_DET_MED (0x1e << 10) 7522 #define MDIO_REG_GPHY_SHADOW_INVERT_FIB_SD (0x1 << 8) 7523 7524 #define IGU_FUNC_BASE 0x0400 7525 7526 #define IGU_ADDR_MSIX 0x0000 7527 #define IGU_ADDR_INT_ACK 0x0200 7528 #define IGU_ADDR_PROD_UPD 0x0201 7529 #define IGU_ADDR_ATTN_BITS_UPD 0x0202 7530 #define IGU_ADDR_ATTN_BITS_SET 0x0203 7531 #define IGU_ADDR_ATTN_BITS_CLR 0x0204 7532 #define IGU_ADDR_COALESCE_NOW 0x0205 7533 #define IGU_ADDR_SIMD_MASK 0x0206 7534 #define IGU_ADDR_SIMD_NOMASK 0x0207 7535 #define IGU_ADDR_MSI_CTL 0x0210 7536 #define IGU_ADDR_MSI_ADDR_LO 0x0211 7537 #define IGU_ADDR_MSI_ADDR_HI 0x0212 7538 #define IGU_ADDR_MSI_DATA 0x0213 7539 7540 #define IGU_USE_REGISTER_ustorm_type_0_sb_cleanup 0 7541 #define IGU_USE_REGISTER_ustorm_type_1_sb_cleanup 1 7542 #define IGU_USE_REGISTER_cstorm_type_0_sb_cleanup 2 7543 #define IGU_USE_REGISTER_cstorm_type_1_sb_cleanup 3 7544 7545 #define COMMAND_REG_INT_ACK 0x0 7546 #define COMMAND_REG_PROD_UPD 0x4 7547 #define COMMAND_REG_ATTN_BITS_UPD 0x8 7548 #define COMMAND_REG_ATTN_BITS_SET 0xc 7549 #define COMMAND_REG_ATTN_BITS_CLR 0x10 7550 #define COMMAND_REG_COALESCE_NOW 0x14 7551 #define COMMAND_REG_SIMD_MASK 0x18 7552 #define COMMAND_REG_SIMD_NOMASK 0x1c 7553 7554 7555 #define IGU_MEM_BASE 0x0000 7556 7557 #define IGU_MEM_MSIX_BASE 0x0000 7558 #define IGU_MEM_MSIX_UPPER 0x007f 7559 #define IGU_MEM_MSIX_RESERVED_UPPER 0x01ff 7560 7561 #define IGU_MEM_PBA_MSIX_BASE 0x0200 7562 #define IGU_MEM_PBA_MSIX_UPPER 0x0200 7563 7564 #define IGU_CMD_BACKWARD_COMP_PROD_UPD 0x0201 7565 #define IGU_MEM_PBA_MSIX_RESERVED_UPPER 0x03ff 7566 7567 #define IGU_CMD_INT_ACK_BASE 0x0400 7568 #define IGU_CMD_INT_ACK_UPPER\ 7569 (IGU_CMD_INT_ACK_BASE + MAX_SB_PER_PORT * NUM_OF_PORTS_PER_PATH - 1) 7570 #define IGU_CMD_INT_ACK_RESERVED_UPPER 0x04ff 7571 7572 #define IGU_CMD_E2_PROD_UPD_BASE 0x0500 7573 #define IGU_CMD_E2_PROD_UPD_UPPER\ 7574 (IGU_CMD_E2_PROD_UPD_BASE + MAX_SB_PER_PORT * NUM_OF_PORTS_PER_PATH - 1) 7575 #define IGU_CMD_E2_PROD_UPD_RESERVED_UPPER 0x059f 7576 7577 #define IGU_CMD_ATTN_BIT_UPD_UPPER 0x05a0 7578 #define IGU_CMD_ATTN_BIT_SET_UPPER 0x05a1 7579 #define IGU_CMD_ATTN_BIT_CLR_UPPER 0x05a2 7580 7581 #define IGU_REG_SISR_MDPC_WMASK_UPPER 0x05a3 7582 #define IGU_REG_SISR_MDPC_WMASK_LSB_UPPER 0x05a4 7583 #define IGU_REG_SISR_MDPC_WMASK_MSB_UPPER 0x05a5 7584 #define IGU_REG_SISR_MDPC_WOMASK_UPPER 0x05a6 7585 7586 #define IGU_REG_RESERVED_UPPER 0x05ff 7587 /* Fields of IGU PF CONFIGURATION REGISTER */ 7588 #define IGU_PF_CONF_FUNC_EN (0x1<<0) /* function enable */ 7589 #define IGU_PF_CONF_MSI_MSIX_EN (0x1<<1) /* MSI/MSIX enable */ 7590 #define IGU_PF_CONF_INT_LINE_EN (0x1<<2) /* INT enable */ 7591 #define IGU_PF_CONF_ATTN_BIT_EN (0x1<<3) /* attention enable */ 7592 #define IGU_PF_CONF_SINGLE_ISR_EN (0x1<<4) /* single ISR mode enable */ 7593 #define IGU_PF_CONF_SIMD_MODE (0x1<<5) /* simd all ones mode */ 7594 7595 /* Fields of IGU VF CONFIGURATION REGISTER */ 7596 #define IGU_VF_CONF_FUNC_EN (0x1<<0) /* function enable */ 7597 #define IGU_VF_CONF_MSI_MSIX_EN (0x1<<1) /* MSI/MSIX enable */ 7598 #define IGU_VF_CONF_PARENT_MASK (0x3<<2) /* Parent PF */ 7599 #define IGU_VF_CONF_PARENT_SHIFT 2 /* Parent PF */ 7600 #define IGU_VF_CONF_SINGLE_ISR_EN (0x1<<4) /* single ISR mode enable */ 7601 7602 7603 #define IGU_BC_DSB_NUM_SEGS 5 7604 #define IGU_BC_NDSB_NUM_SEGS 2 7605 #define IGU_NORM_DSB_NUM_SEGS 2 7606 #define IGU_NORM_NDSB_NUM_SEGS 1 7607 #define IGU_BC_BASE_DSB_PROD 128 7608 #define IGU_NORM_BASE_DSB_PROD 136 7609 7610 /* FID (if VF - [6] = 0; [5:0] = VF number; if PF - [6] = 1; \ 7611 [5:2] = 0; [1:0] = PF number) */ 7612 #define IGU_FID_ENCODE_IS_PF (0x1<<6) 7613 #define IGU_FID_ENCODE_IS_PF_SHIFT 6 7614 #define IGU_FID_VF_NUM_MASK (0x3f) 7615 #define IGU_FID_PF_NUM_MASK (0x7) 7616 7617 #define IGU_REG_MAPPING_MEMORY_VALID (1<<0) 7618 #define IGU_REG_MAPPING_MEMORY_VECTOR_MASK (0x3F<<1) 7619 #define IGU_REG_MAPPING_MEMORY_VECTOR_SHIFT 1 7620 #define IGU_REG_MAPPING_MEMORY_FID_MASK (0x7F<<7) 7621 #define IGU_REG_MAPPING_MEMORY_FID_SHIFT 7 7622 7623 7624 #define CDU_REGION_NUMBER_XCM_AG 2 7625 #define CDU_REGION_NUMBER_UCM_AG 4 7626 7627 7628 /* String-to-compress [31:8] = CID (all 24 bits) 7629 * String-to-compress [7:4] = Region 7630 * String-to-compress [3:0] = Type 7631 */ 7632 #define CDU_VALID_DATA(_cid, _region, _type)\ 7633 (((_cid) << 8) | (((_region)&0xf)<<4) | (((_type)&0xf))) 7634 #define CDU_CRC8(_cid, _region, _type)\ 7635 (calc_crc8(CDU_VALID_DATA(_cid, _region, _type), 0xff)) 7636 #define CDU_RSRVD_VALUE_TYPE_A(_cid, _region, _type)\ 7637 (0x80 | ((CDU_CRC8(_cid, _region, _type)) & 0x7f)) 7638 #define CDU_RSRVD_VALUE_TYPE_B(_crc, _type)\ 7639 (0x80 | ((_type)&0xf << 3) | ((CDU_CRC8(_cid, _region, _type)) & 0x7)) 7640 #define CDU_RSRVD_INVALIDATE_CONTEXT_VALUE(_val) ((_val) & ~0x80) 7641 7642 /****************************************************************************** 7643 * Description: 7644 * Calculates crc 8 on a word value: polynomial 0-1-2-8 7645 * Code was translated from Verilog. 7646 * Return: 7647 *****************************************************************************/ 7648 static inline u8 calc_crc8(u32 data, u8 crc) 7649 { 7650 u8 D[32]; 7651 u8 NewCRC[8]; 7652 u8 C[8]; 7653 u8 crc_res; 7654 u8 i; 7655 7656 /* split the data into 31 bits */ 7657 for (i = 0; i < 32; i++) { 7658 D[i] = (u8)(data & 1); 7659 data = data >> 1; 7660 } 7661 7662 /* split the crc into 8 bits */ 7663 for (i = 0; i < 8; i++) { 7664 C[i] = crc & 1; 7665 crc = crc >> 1; 7666 } 7667 7668 NewCRC[0] = D[31] ^ D[30] ^ D[28] ^ D[23] ^ D[21] ^ D[19] ^ D[18] ^ 7669 D[16] ^ D[14] ^ D[12] ^ D[8] ^ D[7] ^ D[6] ^ D[0] ^ C[4] ^ 7670 C[6] ^ C[7]; 7671 NewCRC[1] = D[30] ^ D[29] ^ D[28] ^ D[24] ^ D[23] ^ D[22] ^ D[21] ^ 7672 D[20] ^ D[18] ^ D[17] ^ D[16] ^ D[15] ^ D[14] ^ D[13] ^ 7673 D[12] ^ D[9] ^ D[6] ^ D[1] ^ D[0] ^ C[0] ^ C[4] ^ C[5] ^ 7674 C[6]; 7675 NewCRC[2] = D[29] ^ D[28] ^ D[25] ^ D[24] ^ D[22] ^ D[17] ^ D[15] ^ 7676 D[13] ^ D[12] ^ D[10] ^ D[8] ^ D[6] ^ D[2] ^ D[1] ^ D[0] ^ 7677 C[0] ^ C[1] ^ C[4] ^ C[5]; 7678 NewCRC[3] = D[30] ^ D[29] ^ D[26] ^ D[25] ^ D[23] ^ D[18] ^ D[16] ^ 7679 D[14] ^ D[13] ^ D[11] ^ D[9] ^ D[7] ^ D[3] ^ D[2] ^ D[1] ^ 7680 C[1] ^ C[2] ^ C[5] ^ C[6]; 7681 NewCRC[4] = D[31] ^ D[30] ^ D[27] ^ D[26] ^ D[24] ^ D[19] ^ D[17] ^ 7682 D[15] ^ D[14] ^ D[12] ^ D[10] ^ D[8] ^ D[4] ^ D[3] ^ D[2] ^ 7683 C[0] ^ C[2] ^ C[3] ^ C[6] ^ C[7]; 7684 NewCRC[5] = D[31] ^ D[28] ^ D[27] ^ D[25] ^ D[20] ^ D[18] ^ D[16] ^ 7685 D[15] ^ D[13] ^ D[11] ^ D[9] ^ D[5] ^ D[4] ^ D[3] ^ C[1] ^ 7686 C[3] ^ C[4] ^ C[7]; 7687 NewCRC[6] = D[29] ^ D[28] ^ D[26] ^ D[21] ^ D[19] ^ D[17] ^ D[16] ^ 7688 D[14] ^ D[12] ^ D[10] ^ D[6] ^ D[5] ^ D[4] ^ C[2] ^ C[4] ^ 7689 C[5]; 7690 NewCRC[7] = D[30] ^ D[29] ^ D[27] ^ D[22] ^ D[20] ^ D[18] ^ D[17] ^ 7691 D[15] ^ D[13] ^ D[11] ^ D[7] ^ D[6] ^ D[5] ^ C[3] ^ C[5] ^ 7692 C[6]; 7693 7694 crc_res = 0; 7695 for (i = 0; i < 8; i++) 7696 crc_res |= (NewCRC[i] << i); 7697 7698 return crc_res; 7699 } 7700 7701 7702 #endif /* BNX2X_REG_H */ 7703