1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Lantiq / Intel GSWIP switch driver for VRX200, xRX300 and xRX330 SoCs 4 * 5 * Copyright (C) 2010 Lantiq Deutschland 6 * Copyright (C) 2012 John Crispin <john@phrozen.org> 7 * Copyright (C) 2017 - 2019 Hauke Mehrtens <hauke@hauke-m.de> 8 * 9 * The VLAN and bridge model the GSWIP hardware uses does not directly 10 * matches the model DSA uses. 11 * 12 * The hardware has 64 possible table entries for bridges with one VLAN 13 * ID, one flow id and a list of ports for each bridge. All entries which 14 * match the same flow ID are combined in the mac learning table, they 15 * act as one global bridge. 16 * The hardware does not support VLAN filter on the port, but on the 17 * bridge, this driver converts the DSA model to the hardware. 18 * 19 * The CPU gets all the exception frames which do not match any forwarding 20 * rule and the CPU port is also added to all bridges. This makes it possible 21 * to handle all the special cases easily in software. 22 * At the initialization the driver allocates one bridge table entry for 23 * each switch port which is used when the port is used without an 24 * explicit bridge. This prevents the frames from being forwarded 25 * between all LAN ports by default. 26 */ 27 28 #include <linux/clk.h> 29 #include <linux/delay.h> 30 #include <linux/etherdevice.h> 31 #include <linux/firmware.h> 32 #include <linux/if_bridge.h> 33 #include <linux/if_vlan.h> 34 #include <linux/iopoll.h> 35 #include <linux/mfd/syscon.h> 36 #include <linux/module.h> 37 #include <linux/of_mdio.h> 38 #include <linux/of_net.h> 39 #include <linux/of_platform.h> 40 #include <linux/phy.h> 41 #include <linux/phylink.h> 42 #include <linux/platform_device.h> 43 #include <linux/regmap.h> 44 #include <linux/reset.h> 45 #include <net/dsa.h> 46 #include <dt-bindings/mips/lantiq_rcu_gphy.h> 47 48 #include "lantiq_pce.h" 49 50 /* GSWIP MDIO Registers */ 51 #define GSWIP_MDIO_GLOB 0x00 52 #define GSWIP_MDIO_GLOB_ENABLE BIT(15) 53 #define GSWIP_MDIO_CTRL 0x08 54 #define GSWIP_MDIO_CTRL_BUSY BIT(12) 55 #define GSWIP_MDIO_CTRL_RD BIT(11) 56 #define GSWIP_MDIO_CTRL_WR BIT(10) 57 #define GSWIP_MDIO_CTRL_PHYAD_MASK 0x1f 58 #define GSWIP_MDIO_CTRL_PHYAD_SHIFT 5 59 #define GSWIP_MDIO_CTRL_REGAD_MASK 0x1f 60 #define GSWIP_MDIO_READ 0x09 61 #define GSWIP_MDIO_WRITE 0x0A 62 #define GSWIP_MDIO_MDC_CFG0 0x0B 63 #define GSWIP_MDIO_MDC_CFG1 0x0C 64 #define GSWIP_MDIO_PHYp(p) (0x15 - (p)) 65 #define GSWIP_MDIO_PHY_LINK_MASK 0x6000 66 #define GSWIP_MDIO_PHY_LINK_AUTO 0x0000 67 #define GSWIP_MDIO_PHY_LINK_DOWN 0x4000 68 #define GSWIP_MDIO_PHY_LINK_UP 0x2000 69 #define GSWIP_MDIO_PHY_SPEED_MASK 0x1800 70 #define GSWIP_MDIO_PHY_SPEED_AUTO 0x1800 71 #define GSWIP_MDIO_PHY_SPEED_M10 0x0000 72 #define GSWIP_MDIO_PHY_SPEED_M100 0x0800 73 #define GSWIP_MDIO_PHY_SPEED_G1 0x1000 74 #define GSWIP_MDIO_PHY_FDUP_MASK 0x0600 75 #define GSWIP_MDIO_PHY_FDUP_AUTO 0x0000 76 #define GSWIP_MDIO_PHY_FDUP_EN 0x0200 77 #define GSWIP_MDIO_PHY_FDUP_DIS 0x0600 78 #define GSWIP_MDIO_PHY_FCONTX_MASK 0x0180 79 #define GSWIP_MDIO_PHY_FCONTX_AUTO 0x0000 80 #define GSWIP_MDIO_PHY_FCONTX_EN 0x0100 81 #define GSWIP_MDIO_PHY_FCONTX_DIS 0x0180 82 #define GSWIP_MDIO_PHY_FCONRX_MASK 0x0060 83 #define GSWIP_MDIO_PHY_FCONRX_AUTO 0x0000 84 #define GSWIP_MDIO_PHY_FCONRX_EN 0x0020 85 #define GSWIP_MDIO_PHY_FCONRX_DIS 0x0060 86 #define GSWIP_MDIO_PHY_ADDR_MASK 0x001f 87 #define GSWIP_MDIO_PHY_MASK (GSWIP_MDIO_PHY_ADDR_MASK | \ 88 GSWIP_MDIO_PHY_FCONRX_MASK | \ 89 GSWIP_MDIO_PHY_FCONTX_MASK | \ 90 GSWIP_MDIO_PHY_LINK_MASK | \ 91 GSWIP_MDIO_PHY_SPEED_MASK | \ 92 GSWIP_MDIO_PHY_FDUP_MASK) 93 94 /* GSWIP MII Registers */ 95 #define GSWIP_MII_CFGp(p) (0x2 * (p)) 96 #define GSWIP_MII_CFG_RESET BIT(15) 97 #define GSWIP_MII_CFG_EN BIT(14) 98 #define GSWIP_MII_CFG_ISOLATE BIT(13) 99 #define GSWIP_MII_CFG_LDCLKDIS BIT(12) 100 #define GSWIP_MII_CFG_RGMII_IBS BIT(8) 101 #define GSWIP_MII_CFG_RMII_CLK BIT(7) 102 #define GSWIP_MII_CFG_MODE_MIIP 0x0 103 #define GSWIP_MII_CFG_MODE_MIIM 0x1 104 #define GSWIP_MII_CFG_MODE_RMIIP 0x2 105 #define GSWIP_MII_CFG_MODE_RMIIM 0x3 106 #define GSWIP_MII_CFG_MODE_RGMII 0x4 107 #define GSWIP_MII_CFG_MODE_GMII 0x9 108 #define GSWIP_MII_CFG_MODE_MASK 0xf 109 #define GSWIP_MII_CFG_RATE_M2P5 0x00 110 #define GSWIP_MII_CFG_RATE_M25 0x10 111 #define GSWIP_MII_CFG_RATE_M125 0x20 112 #define GSWIP_MII_CFG_RATE_M50 0x30 113 #define GSWIP_MII_CFG_RATE_AUTO 0x40 114 #define GSWIP_MII_CFG_RATE_MASK 0x70 115 #define GSWIP_MII_PCDU0 0x01 116 #define GSWIP_MII_PCDU1 0x03 117 #define GSWIP_MII_PCDU5 0x05 118 #define GSWIP_MII_PCDU_TXDLY_MASK GENMASK(2, 0) 119 #define GSWIP_MII_PCDU_RXDLY_MASK GENMASK(9, 7) 120 121 /* GSWIP Core Registers */ 122 #define GSWIP_SWRES 0x000 123 #define GSWIP_SWRES_R1 BIT(1) /* GSWIP Software reset */ 124 #define GSWIP_SWRES_R0 BIT(0) /* GSWIP Hardware reset */ 125 #define GSWIP_VERSION 0x013 126 #define GSWIP_VERSION_REV_SHIFT 0 127 #define GSWIP_VERSION_REV_MASK GENMASK(7, 0) 128 #define GSWIP_VERSION_MOD_SHIFT 8 129 #define GSWIP_VERSION_MOD_MASK GENMASK(15, 8) 130 #define GSWIP_VERSION_2_0 0x100 131 #define GSWIP_VERSION_2_1 0x021 132 #define GSWIP_VERSION_2_2 0x122 133 #define GSWIP_VERSION_2_2_ETC 0x022 134 135 #define GSWIP_BM_RAM_VAL(x) (0x043 - (x)) 136 #define GSWIP_BM_RAM_ADDR 0x044 137 #define GSWIP_BM_RAM_CTRL 0x045 138 #define GSWIP_BM_RAM_CTRL_BAS BIT(15) 139 #define GSWIP_BM_RAM_CTRL_OPMOD BIT(5) 140 #define GSWIP_BM_RAM_CTRL_ADDR_MASK GENMASK(4, 0) 141 #define GSWIP_BM_QUEUE_GCTRL 0x04A 142 #define GSWIP_BM_QUEUE_GCTRL_GL_MOD BIT(10) 143 /* buffer management Port Configuration Register */ 144 #define GSWIP_BM_PCFGp(p) (0x080 + ((p) * 2)) 145 #define GSWIP_BM_PCFG_CNTEN BIT(0) /* RMON Counter Enable */ 146 #define GSWIP_BM_PCFG_IGCNT BIT(1) /* Ingres Special Tag RMON count */ 147 /* buffer management Port Control Register */ 148 #define GSWIP_BM_RMON_CTRLp(p) (0x81 + ((p) * 2)) 149 #define GSWIP_BM_CTRL_RMON_RAM1_RES BIT(0) /* Software Reset for RMON RAM 1 */ 150 #define GSWIP_BM_CTRL_RMON_RAM2_RES BIT(1) /* Software Reset for RMON RAM 2 */ 151 152 /* PCE */ 153 #define GSWIP_PCE_TBL_KEY(x) (0x447 - (x)) 154 #define GSWIP_PCE_TBL_MASK 0x448 155 #define GSWIP_PCE_TBL_VAL(x) (0x44D - (x)) 156 #define GSWIP_PCE_TBL_ADDR 0x44E 157 #define GSWIP_PCE_TBL_CTRL 0x44F 158 #define GSWIP_PCE_TBL_CTRL_BAS BIT(15) 159 #define GSWIP_PCE_TBL_CTRL_TYPE BIT(13) 160 #define GSWIP_PCE_TBL_CTRL_VLD BIT(12) 161 #define GSWIP_PCE_TBL_CTRL_KEYFORM BIT(11) 162 #define GSWIP_PCE_TBL_CTRL_GMAP_MASK GENMASK(10, 7) 163 #define GSWIP_PCE_TBL_CTRL_OPMOD_MASK GENMASK(6, 5) 164 #define GSWIP_PCE_TBL_CTRL_OPMOD_ADRD 0x00 165 #define GSWIP_PCE_TBL_CTRL_OPMOD_ADWR 0x20 166 #define GSWIP_PCE_TBL_CTRL_OPMOD_KSRD 0x40 167 #define GSWIP_PCE_TBL_CTRL_OPMOD_KSWR 0x60 168 #define GSWIP_PCE_TBL_CTRL_ADDR_MASK GENMASK(4, 0) 169 #define GSWIP_PCE_PMAP1 0x453 /* Monitoring port map */ 170 #define GSWIP_PCE_PMAP2 0x454 /* Default Multicast port map */ 171 #define GSWIP_PCE_PMAP3 0x455 /* Default Unknown Unicast port map */ 172 #define GSWIP_PCE_GCTRL_0 0x456 173 #define GSWIP_PCE_GCTRL_0_MTFL BIT(0) /* MAC Table Flushing */ 174 #define GSWIP_PCE_GCTRL_0_MC_VALID BIT(3) 175 #define GSWIP_PCE_GCTRL_0_VLAN BIT(14) /* VLAN aware Switching */ 176 #define GSWIP_PCE_GCTRL_1 0x457 177 #define GSWIP_PCE_GCTRL_1_MAC_GLOCK BIT(2) /* MAC Address table lock */ 178 #define GSWIP_PCE_GCTRL_1_MAC_GLOCK_MOD BIT(3) /* Mac address table lock forwarding mode */ 179 #define GSWIP_PCE_PCTRL_0p(p) (0x480 + ((p) * 0xA)) 180 #define GSWIP_PCE_PCTRL_0_TVM BIT(5) /* Transparent VLAN mode */ 181 #define GSWIP_PCE_PCTRL_0_VREP BIT(6) /* VLAN Replace Mode */ 182 #define GSWIP_PCE_PCTRL_0_INGRESS BIT(11) /* Accept special tag in ingress */ 183 #define GSWIP_PCE_PCTRL_0_PSTATE_LISTEN 0x0 184 #define GSWIP_PCE_PCTRL_0_PSTATE_RX 0x1 185 #define GSWIP_PCE_PCTRL_0_PSTATE_TX 0x2 186 #define GSWIP_PCE_PCTRL_0_PSTATE_LEARNING 0x3 187 #define GSWIP_PCE_PCTRL_0_PSTATE_FORWARDING 0x7 188 #define GSWIP_PCE_PCTRL_0_PSTATE_MASK GENMASK(2, 0) 189 #define GSWIP_PCE_VCTRL(p) (0x485 + ((p) * 0xA)) 190 #define GSWIP_PCE_VCTRL_UVR BIT(0) /* Unknown VLAN Rule */ 191 #define GSWIP_PCE_VCTRL_VIMR BIT(3) /* VLAN Ingress Member violation rule */ 192 #define GSWIP_PCE_VCTRL_VEMR BIT(4) /* VLAN Egress Member violation rule */ 193 #define GSWIP_PCE_VCTRL_VSR BIT(5) /* VLAN Security */ 194 #define GSWIP_PCE_VCTRL_VID0 BIT(6) /* Priority Tagged Rule */ 195 #define GSWIP_PCE_DEFPVID(p) (0x486 + ((p) * 0xA)) 196 197 #define GSWIP_MAC_FLEN 0x8C5 198 #define GSWIP_MAC_CTRL_0p(p) (0x903 + ((p) * 0xC)) 199 #define GSWIP_MAC_CTRL_0_PADEN BIT(8) 200 #define GSWIP_MAC_CTRL_0_FCS_EN BIT(7) 201 #define GSWIP_MAC_CTRL_0_FCON_MASK 0x0070 202 #define GSWIP_MAC_CTRL_0_FCON_AUTO 0x0000 203 #define GSWIP_MAC_CTRL_0_FCON_RX 0x0010 204 #define GSWIP_MAC_CTRL_0_FCON_TX 0x0020 205 #define GSWIP_MAC_CTRL_0_FCON_RXTX 0x0030 206 #define GSWIP_MAC_CTRL_0_FCON_NONE 0x0040 207 #define GSWIP_MAC_CTRL_0_FDUP_MASK 0x000C 208 #define GSWIP_MAC_CTRL_0_FDUP_AUTO 0x0000 209 #define GSWIP_MAC_CTRL_0_FDUP_EN 0x0004 210 #define GSWIP_MAC_CTRL_0_FDUP_DIS 0x000C 211 #define GSWIP_MAC_CTRL_0_GMII_MASK 0x0003 212 #define GSWIP_MAC_CTRL_0_GMII_AUTO 0x0000 213 #define GSWIP_MAC_CTRL_0_GMII_MII 0x0001 214 #define GSWIP_MAC_CTRL_0_GMII_RGMII 0x0002 215 #define GSWIP_MAC_CTRL_2p(p) (0x905 + ((p) * 0xC)) 216 #define GSWIP_MAC_CTRL_2_MLEN BIT(3) /* Maximum Untagged Frame Lnegth */ 217 218 /* Ethernet Switch Fetch DMA Port Control Register */ 219 #define GSWIP_FDMA_PCTRLp(p) (0xA80 + ((p) * 0x6)) 220 #define GSWIP_FDMA_PCTRL_EN BIT(0) /* FDMA Port Enable */ 221 #define GSWIP_FDMA_PCTRL_STEN BIT(1) /* Special Tag Insertion Enable */ 222 #define GSWIP_FDMA_PCTRL_VLANMOD_MASK GENMASK(4, 3) /* VLAN Modification Control */ 223 #define GSWIP_FDMA_PCTRL_VLANMOD_SHIFT 3 /* VLAN Modification Control */ 224 #define GSWIP_FDMA_PCTRL_VLANMOD_DIS (0x0 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT) 225 #define GSWIP_FDMA_PCTRL_VLANMOD_PRIO (0x1 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT) 226 #define GSWIP_FDMA_PCTRL_VLANMOD_ID (0x2 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT) 227 #define GSWIP_FDMA_PCTRL_VLANMOD_BOTH (0x3 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT) 228 229 /* Ethernet Switch Store DMA Port Control Register */ 230 #define GSWIP_SDMA_PCTRLp(p) (0xBC0 + ((p) * 0x6)) 231 #define GSWIP_SDMA_PCTRL_EN BIT(0) /* SDMA Port Enable */ 232 #define GSWIP_SDMA_PCTRL_FCEN BIT(1) /* Flow Control Enable */ 233 #define GSWIP_SDMA_PCTRL_PAUFWD BIT(1) /* Pause Frame Forwarding */ 234 235 #define GSWIP_TABLE_ACTIVE_VLAN 0x01 236 #define GSWIP_TABLE_VLAN_MAPPING 0x02 237 #define GSWIP_TABLE_MAC_BRIDGE 0x0b 238 #define GSWIP_TABLE_MAC_BRIDGE_STATIC 0x01 /* Static not, aging entry */ 239 240 #define XRX200_GPHY_FW_ALIGN (16 * 1024) 241 242 struct gswip_hw_info { 243 int max_ports; 244 int cpu_port; 245 const struct dsa_switch_ops *ops; 246 }; 247 248 struct xway_gphy_match_data { 249 char *fe_firmware_name; 250 char *ge_firmware_name; 251 }; 252 253 struct gswip_gphy_fw { 254 struct clk *clk_gate; 255 struct reset_control *reset; 256 u32 fw_addr_offset; 257 char *fw_name; 258 }; 259 260 struct gswip_vlan { 261 struct net_device *bridge; 262 u16 vid; 263 u8 fid; 264 }; 265 266 struct gswip_priv { 267 __iomem void *gswip; 268 __iomem void *mdio; 269 __iomem void *mii; 270 const struct gswip_hw_info *hw_info; 271 const struct xway_gphy_match_data *gphy_fw_name_cfg; 272 struct dsa_switch *ds; 273 struct device *dev; 274 struct regmap *rcu_regmap; 275 struct gswip_vlan vlans[64]; 276 int num_gphy_fw; 277 struct gswip_gphy_fw *gphy_fw; 278 u32 port_vlan_filter; 279 }; 280 281 struct gswip_pce_table_entry { 282 u16 index; // PCE_TBL_ADDR.ADDR = pData->table_index 283 u16 table; // PCE_TBL_CTRL.ADDR = pData->table 284 u16 key[8]; 285 u16 val[5]; 286 u16 mask; 287 u8 gmap; 288 bool type; 289 bool valid; 290 bool key_mode; 291 }; 292 293 struct gswip_rmon_cnt_desc { 294 unsigned int size; 295 unsigned int offset; 296 const char *name; 297 }; 298 299 #define MIB_DESC(_size, _offset, _name) {.size = _size, .offset = _offset, .name = _name} 300 301 static const struct gswip_rmon_cnt_desc gswip_rmon_cnt[] = { 302 /** Receive Packet Count (only packets that are accepted and not discarded). */ 303 MIB_DESC(1, 0x1F, "RxGoodPkts"), 304 MIB_DESC(1, 0x23, "RxUnicastPkts"), 305 MIB_DESC(1, 0x22, "RxMulticastPkts"), 306 MIB_DESC(1, 0x21, "RxFCSErrorPkts"), 307 MIB_DESC(1, 0x1D, "RxUnderSizeGoodPkts"), 308 MIB_DESC(1, 0x1E, "RxUnderSizeErrorPkts"), 309 MIB_DESC(1, 0x1B, "RxOversizeGoodPkts"), 310 MIB_DESC(1, 0x1C, "RxOversizeErrorPkts"), 311 MIB_DESC(1, 0x20, "RxGoodPausePkts"), 312 MIB_DESC(1, 0x1A, "RxAlignErrorPkts"), 313 MIB_DESC(1, 0x12, "Rx64BytePkts"), 314 MIB_DESC(1, 0x13, "Rx127BytePkts"), 315 MIB_DESC(1, 0x14, "Rx255BytePkts"), 316 MIB_DESC(1, 0x15, "Rx511BytePkts"), 317 MIB_DESC(1, 0x16, "Rx1023BytePkts"), 318 /** Receive Size 1024-1522 (or more, if configured) Packet Count. */ 319 MIB_DESC(1, 0x17, "RxMaxBytePkts"), 320 MIB_DESC(1, 0x18, "RxDroppedPkts"), 321 MIB_DESC(1, 0x19, "RxFilteredPkts"), 322 MIB_DESC(2, 0x24, "RxGoodBytes"), 323 MIB_DESC(2, 0x26, "RxBadBytes"), 324 MIB_DESC(1, 0x11, "TxAcmDroppedPkts"), 325 MIB_DESC(1, 0x0C, "TxGoodPkts"), 326 MIB_DESC(1, 0x06, "TxUnicastPkts"), 327 MIB_DESC(1, 0x07, "TxMulticastPkts"), 328 MIB_DESC(1, 0x00, "Tx64BytePkts"), 329 MIB_DESC(1, 0x01, "Tx127BytePkts"), 330 MIB_DESC(1, 0x02, "Tx255BytePkts"), 331 MIB_DESC(1, 0x03, "Tx511BytePkts"), 332 MIB_DESC(1, 0x04, "Tx1023BytePkts"), 333 /** Transmit Size 1024-1522 (or more, if configured) Packet Count. */ 334 MIB_DESC(1, 0x05, "TxMaxBytePkts"), 335 MIB_DESC(1, 0x08, "TxSingleCollCount"), 336 MIB_DESC(1, 0x09, "TxMultCollCount"), 337 MIB_DESC(1, 0x0A, "TxLateCollCount"), 338 MIB_DESC(1, 0x0B, "TxExcessCollCount"), 339 MIB_DESC(1, 0x0D, "TxPauseCount"), 340 MIB_DESC(1, 0x10, "TxDroppedPkts"), 341 MIB_DESC(2, 0x0E, "TxGoodBytes"), 342 }; 343 344 static u32 gswip_switch_r(struct gswip_priv *priv, u32 offset) 345 { 346 return __raw_readl(priv->gswip + (offset * 4)); 347 } 348 349 static void gswip_switch_w(struct gswip_priv *priv, u32 val, u32 offset) 350 { 351 __raw_writel(val, priv->gswip + (offset * 4)); 352 } 353 354 static void gswip_switch_mask(struct gswip_priv *priv, u32 clear, u32 set, 355 u32 offset) 356 { 357 u32 val = gswip_switch_r(priv, offset); 358 359 val &= ~(clear); 360 val |= set; 361 gswip_switch_w(priv, val, offset); 362 } 363 364 static u32 gswip_switch_r_timeout(struct gswip_priv *priv, u32 offset, 365 u32 cleared) 366 { 367 u32 val; 368 369 return readx_poll_timeout(__raw_readl, priv->gswip + (offset * 4), val, 370 (val & cleared) == 0, 20, 50000); 371 } 372 373 static u32 gswip_mdio_r(struct gswip_priv *priv, u32 offset) 374 { 375 return __raw_readl(priv->mdio + (offset * 4)); 376 } 377 378 static void gswip_mdio_w(struct gswip_priv *priv, u32 val, u32 offset) 379 { 380 __raw_writel(val, priv->mdio + (offset * 4)); 381 } 382 383 static void gswip_mdio_mask(struct gswip_priv *priv, u32 clear, u32 set, 384 u32 offset) 385 { 386 u32 val = gswip_mdio_r(priv, offset); 387 388 val &= ~(clear); 389 val |= set; 390 gswip_mdio_w(priv, val, offset); 391 } 392 393 static u32 gswip_mii_r(struct gswip_priv *priv, u32 offset) 394 { 395 return __raw_readl(priv->mii + (offset * 4)); 396 } 397 398 static void gswip_mii_w(struct gswip_priv *priv, u32 val, u32 offset) 399 { 400 __raw_writel(val, priv->mii + (offset * 4)); 401 } 402 403 static void gswip_mii_mask(struct gswip_priv *priv, u32 clear, u32 set, 404 u32 offset) 405 { 406 u32 val = gswip_mii_r(priv, offset); 407 408 val &= ~(clear); 409 val |= set; 410 gswip_mii_w(priv, val, offset); 411 } 412 413 static void gswip_mii_mask_cfg(struct gswip_priv *priv, u32 clear, u32 set, 414 int port) 415 { 416 /* There's no MII_CFG register for the CPU port */ 417 if (!dsa_is_cpu_port(priv->ds, port)) 418 gswip_mii_mask(priv, clear, set, GSWIP_MII_CFGp(port)); 419 } 420 421 static void gswip_mii_mask_pcdu(struct gswip_priv *priv, u32 clear, u32 set, 422 int port) 423 { 424 switch (port) { 425 case 0: 426 gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU0); 427 break; 428 case 1: 429 gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU1); 430 break; 431 case 5: 432 gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU5); 433 break; 434 } 435 } 436 437 static int gswip_mdio_poll(struct gswip_priv *priv) 438 { 439 int cnt = 100; 440 441 while (likely(cnt--)) { 442 u32 ctrl = gswip_mdio_r(priv, GSWIP_MDIO_CTRL); 443 444 if ((ctrl & GSWIP_MDIO_CTRL_BUSY) == 0) 445 return 0; 446 usleep_range(20, 40); 447 } 448 449 return -ETIMEDOUT; 450 } 451 452 static int gswip_mdio_wr(struct mii_bus *bus, int addr, int reg, u16 val) 453 { 454 struct gswip_priv *priv = bus->priv; 455 int err; 456 457 err = gswip_mdio_poll(priv); 458 if (err) { 459 dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n"); 460 return err; 461 } 462 463 gswip_mdio_w(priv, val, GSWIP_MDIO_WRITE); 464 gswip_mdio_w(priv, GSWIP_MDIO_CTRL_BUSY | GSWIP_MDIO_CTRL_WR | 465 ((addr & GSWIP_MDIO_CTRL_PHYAD_MASK) << GSWIP_MDIO_CTRL_PHYAD_SHIFT) | 466 (reg & GSWIP_MDIO_CTRL_REGAD_MASK), 467 GSWIP_MDIO_CTRL); 468 469 return 0; 470 } 471 472 static int gswip_mdio_rd(struct mii_bus *bus, int addr, int reg) 473 { 474 struct gswip_priv *priv = bus->priv; 475 int err; 476 477 err = gswip_mdio_poll(priv); 478 if (err) { 479 dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n"); 480 return err; 481 } 482 483 gswip_mdio_w(priv, GSWIP_MDIO_CTRL_BUSY | GSWIP_MDIO_CTRL_RD | 484 ((addr & GSWIP_MDIO_CTRL_PHYAD_MASK) << GSWIP_MDIO_CTRL_PHYAD_SHIFT) | 485 (reg & GSWIP_MDIO_CTRL_REGAD_MASK), 486 GSWIP_MDIO_CTRL); 487 488 err = gswip_mdio_poll(priv); 489 if (err) { 490 dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n"); 491 return err; 492 } 493 494 return gswip_mdio_r(priv, GSWIP_MDIO_READ); 495 } 496 497 static int gswip_mdio(struct gswip_priv *priv, struct device_node *mdio_np) 498 { 499 struct dsa_switch *ds = priv->ds; 500 501 ds->slave_mii_bus = devm_mdiobus_alloc(priv->dev); 502 if (!ds->slave_mii_bus) 503 return -ENOMEM; 504 505 ds->slave_mii_bus->priv = priv; 506 ds->slave_mii_bus->read = gswip_mdio_rd; 507 ds->slave_mii_bus->write = gswip_mdio_wr; 508 ds->slave_mii_bus->name = "lantiq,xrx200-mdio"; 509 snprintf(ds->slave_mii_bus->id, MII_BUS_ID_SIZE, "%s-mii", 510 dev_name(priv->dev)); 511 ds->slave_mii_bus->parent = priv->dev; 512 ds->slave_mii_bus->phy_mask = ~ds->phys_mii_mask; 513 514 return of_mdiobus_register(ds->slave_mii_bus, mdio_np); 515 } 516 517 static int gswip_pce_table_entry_read(struct gswip_priv *priv, 518 struct gswip_pce_table_entry *tbl) 519 { 520 int i; 521 int err; 522 u16 crtl; 523 u16 addr_mode = tbl->key_mode ? GSWIP_PCE_TBL_CTRL_OPMOD_KSRD : 524 GSWIP_PCE_TBL_CTRL_OPMOD_ADRD; 525 526 err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, 527 GSWIP_PCE_TBL_CTRL_BAS); 528 if (err) 529 return err; 530 531 gswip_switch_w(priv, tbl->index, GSWIP_PCE_TBL_ADDR); 532 gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK | 533 GSWIP_PCE_TBL_CTRL_OPMOD_MASK, 534 tbl->table | addr_mode | GSWIP_PCE_TBL_CTRL_BAS, 535 GSWIP_PCE_TBL_CTRL); 536 537 err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, 538 GSWIP_PCE_TBL_CTRL_BAS); 539 if (err) 540 return err; 541 542 for (i = 0; i < ARRAY_SIZE(tbl->key); i++) 543 tbl->key[i] = gswip_switch_r(priv, GSWIP_PCE_TBL_KEY(i)); 544 545 for (i = 0; i < ARRAY_SIZE(tbl->val); i++) 546 tbl->val[i] = gswip_switch_r(priv, GSWIP_PCE_TBL_VAL(i)); 547 548 tbl->mask = gswip_switch_r(priv, GSWIP_PCE_TBL_MASK); 549 550 crtl = gswip_switch_r(priv, GSWIP_PCE_TBL_CTRL); 551 552 tbl->type = !!(crtl & GSWIP_PCE_TBL_CTRL_TYPE); 553 tbl->valid = !!(crtl & GSWIP_PCE_TBL_CTRL_VLD); 554 tbl->gmap = (crtl & GSWIP_PCE_TBL_CTRL_GMAP_MASK) >> 7; 555 556 return 0; 557 } 558 559 static int gswip_pce_table_entry_write(struct gswip_priv *priv, 560 struct gswip_pce_table_entry *tbl) 561 { 562 int i; 563 int err; 564 u16 crtl; 565 u16 addr_mode = tbl->key_mode ? GSWIP_PCE_TBL_CTRL_OPMOD_KSWR : 566 GSWIP_PCE_TBL_CTRL_OPMOD_ADWR; 567 568 err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, 569 GSWIP_PCE_TBL_CTRL_BAS); 570 if (err) 571 return err; 572 573 gswip_switch_w(priv, tbl->index, GSWIP_PCE_TBL_ADDR); 574 gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK | 575 GSWIP_PCE_TBL_CTRL_OPMOD_MASK, 576 tbl->table | addr_mode, 577 GSWIP_PCE_TBL_CTRL); 578 579 for (i = 0; i < ARRAY_SIZE(tbl->key); i++) 580 gswip_switch_w(priv, tbl->key[i], GSWIP_PCE_TBL_KEY(i)); 581 582 for (i = 0; i < ARRAY_SIZE(tbl->val); i++) 583 gswip_switch_w(priv, tbl->val[i], GSWIP_PCE_TBL_VAL(i)); 584 585 gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK | 586 GSWIP_PCE_TBL_CTRL_OPMOD_MASK, 587 tbl->table | addr_mode, 588 GSWIP_PCE_TBL_CTRL); 589 590 gswip_switch_w(priv, tbl->mask, GSWIP_PCE_TBL_MASK); 591 592 crtl = gswip_switch_r(priv, GSWIP_PCE_TBL_CTRL); 593 crtl &= ~(GSWIP_PCE_TBL_CTRL_TYPE | GSWIP_PCE_TBL_CTRL_VLD | 594 GSWIP_PCE_TBL_CTRL_GMAP_MASK); 595 if (tbl->type) 596 crtl |= GSWIP_PCE_TBL_CTRL_TYPE; 597 if (tbl->valid) 598 crtl |= GSWIP_PCE_TBL_CTRL_VLD; 599 crtl |= (tbl->gmap << 7) & GSWIP_PCE_TBL_CTRL_GMAP_MASK; 600 crtl |= GSWIP_PCE_TBL_CTRL_BAS; 601 gswip_switch_w(priv, crtl, GSWIP_PCE_TBL_CTRL); 602 603 return gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, 604 GSWIP_PCE_TBL_CTRL_BAS); 605 } 606 607 /* Add the LAN port into a bridge with the CPU port by 608 * default. This prevents automatic forwarding of 609 * packages between the LAN ports when no explicit 610 * bridge is configured. 611 */ 612 static int gswip_add_single_port_br(struct gswip_priv *priv, int port, bool add) 613 { 614 struct gswip_pce_table_entry vlan_active = {0,}; 615 struct gswip_pce_table_entry vlan_mapping = {0,}; 616 unsigned int cpu_port = priv->hw_info->cpu_port; 617 unsigned int max_ports = priv->hw_info->max_ports; 618 int err; 619 620 if (port >= max_ports) { 621 dev_err(priv->dev, "single port for %i supported\n", port); 622 return -EIO; 623 } 624 625 vlan_active.index = port + 1; 626 vlan_active.table = GSWIP_TABLE_ACTIVE_VLAN; 627 vlan_active.key[0] = 0; /* vid */ 628 vlan_active.val[0] = port + 1 /* fid */; 629 vlan_active.valid = add; 630 err = gswip_pce_table_entry_write(priv, &vlan_active); 631 if (err) { 632 dev_err(priv->dev, "failed to write active VLAN: %d\n", err); 633 return err; 634 } 635 636 if (!add) 637 return 0; 638 639 vlan_mapping.index = port + 1; 640 vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; 641 vlan_mapping.val[0] = 0 /* vid */; 642 vlan_mapping.val[1] = BIT(port) | BIT(cpu_port); 643 vlan_mapping.val[2] = 0; 644 err = gswip_pce_table_entry_write(priv, &vlan_mapping); 645 if (err) { 646 dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err); 647 return err; 648 } 649 650 return 0; 651 } 652 653 static int gswip_port_enable(struct dsa_switch *ds, int port, 654 struct phy_device *phydev) 655 { 656 struct gswip_priv *priv = ds->priv; 657 int err; 658 659 if (!dsa_is_user_port(ds, port)) 660 return 0; 661 662 if (!dsa_is_cpu_port(ds, port)) { 663 err = gswip_add_single_port_br(priv, port, true); 664 if (err) 665 return err; 666 } 667 668 /* RMON Counter Enable for port */ 669 gswip_switch_w(priv, GSWIP_BM_PCFG_CNTEN, GSWIP_BM_PCFGp(port)); 670 671 /* enable port fetch/store dma & VLAN Modification */ 672 gswip_switch_mask(priv, 0, GSWIP_FDMA_PCTRL_EN | 673 GSWIP_FDMA_PCTRL_VLANMOD_BOTH, 674 GSWIP_FDMA_PCTRLp(port)); 675 gswip_switch_mask(priv, 0, GSWIP_SDMA_PCTRL_EN, 676 GSWIP_SDMA_PCTRLp(port)); 677 678 if (!dsa_is_cpu_port(ds, port)) { 679 u32 mdio_phy = 0; 680 681 if (phydev) 682 mdio_phy = phydev->mdio.addr & GSWIP_MDIO_PHY_ADDR_MASK; 683 684 gswip_mdio_mask(priv, GSWIP_MDIO_PHY_ADDR_MASK, mdio_phy, 685 GSWIP_MDIO_PHYp(port)); 686 } 687 688 return 0; 689 } 690 691 static void gswip_port_disable(struct dsa_switch *ds, int port) 692 { 693 struct gswip_priv *priv = ds->priv; 694 695 if (!dsa_is_user_port(ds, port)) 696 return; 697 698 gswip_switch_mask(priv, GSWIP_FDMA_PCTRL_EN, 0, 699 GSWIP_FDMA_PCTRLp(port)); 700 gswip_switch_mask(priv, GSWIP_SDMA_PCTRL_EN, 0, 701 GSWIP_SDMA_PCTRLp(port)); 702 } 703 704 static int gswip_pce_load_microcode(struct gswip_priv *priv) 705 { 706 int i; 707 int err; 708 709 gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK | 710 GSWIP_PCE_TBL_CTRL_OPMOD_MASK, 711 GSWIP_PCE_TBL_CTRL_OPMOD_ADWR, GSWIP_PCE_TBL_CTRL); 712 gswip_switch_w(priv, 0, GSWIP_PCE_TBL_MASK); 713 714 for (i = 0; i < ARRAY_SIZE(gswip_pce_microcode); i++) { 715 gswip_switch_w(priv, i, GSWIP_PCE_TBL_ADDR); 716 gswip_switch_w(priv, gswip_pce_microcode[i].val_0, 717 GSWIP_PCE_TBL_VAL(0)); 718 gswip_switch_w(priv, gswip_pce_microcode[i].val_1, 719 GSWIP_PCE_TBL_VAL(1)); 720 gswip_switch_w(priv, gswip_pce_microcode[i].val_2, 721 GSWIP_PCE_TBL_VAL(2)); 722 gswip_switch_w(priv, gswip_pce_microcode[i].val_3, 723 GSWIP_PCE_TBL_VAL(3)); 724 725 /* start the table access: */ 726 gswip_switch_mask(priv, 0, GSWIP_PCE_TBL_CTRL_BAS, 727 GSWIP_PCE_TBL_CTRL); 728 err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, 729 GSWIP_PCE_TBL_CTRL_BAS); 730 if (err) 731 return err; 732 } 733 734 /* tell the switch that the microcode is loaded */ 735 gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_MC_VALID, 736 GSWIP_PCE_GCTRL_0); 737 738 return 0; 739 } 740 741 static int gswip_port_vlan_filtering(struct dsa_switch *ds, int port, 742 bool vlan_filtering, 743 struct netlink_ext_ack *extack) 744 { 745 struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev; 746 struct gswip_priv *priv = ds->priv; 747 748 /* Do not allow changing the VLAN filtering options while in bridge */ 749 if (bridge && !!(priv->port_vlan_filter & BIT(port)) != vlan_filtering) { 750 NL_SET_ERR_MSG_MOD(extack, 751 "Dynamic toggling of vlan_filtering not supported"); 752 return -EIO; 753 } 754 755 if (vlan_filtering) { 756 /* Use port based VLAN tag */ 757 gswip_switch_mask(priv, 758 GSWIP_PCE_VCTRL_VSR, 759 GSWIP_PCE_VCTRL_UVR | GSWIP_PCE_VCTRL_VIMR | 760 GSWIP_PCE_VCTRL_VEMR, 761 GSWIP_PCE_VCTRL(port)); 762 gswip_switch_mask(priv, GSWIP_PCE_PCTRL_0_TVM, 0, 763 GSWIP_PCE_PCTRL_0p(port)); 764 } else { 765 /* Use port based VLAN tag */ 766 gswip_switch_mask(priv, 767 GSWIP_PCE_VCTRL_UVR | GSWIP_PCE_VCTRL_VIMR | 768 GSWIP_PCE_VCTRL_VEMR, 769 GSWIP_PCE_VCTRL_VSR, 770 GSWIP_PCE_VCTRL(port)); 771 gswip_switch_mask(priv, 0, GSWIP_PCE_PCTRL_0_TVM, 772 GSWIP_PCE_PCTRL_0p(port)); 773 } 774 775 return 0; 776 } 777 778 static int gswip_setup(struct dsa_switch *ds) 779 { 780 struct gswip_priv *priv = ds->priv; 781 unsigned int cpu_port = priv->hw_info->cpu_port; 782 int i; 783 int err; 784 785 gswip_switch_w(priv, GSWIP_SWRES_R0, GSWIP_SWRES); 786 usleep_range(5000, 10000); 787 gswip_switch_w(priv, 0, GSWIP_SWRES); 788 789 /* disable port fetch/store dma on all ports */ 790 for (i = 0; i < priv->hw_info->max_ports; i++) { 791 gswip_port_disable(ds, i); 792 gswip_port_vlan_filtering(ds, i, false, NULL); 793 } 794 795 /* enable Switch */ 796 gswip_mdio_mask(priv, 0, GSWIP_MDIO_GLOB_ENABLE, GSWIP_MDIO_GLOB); 797 798 err = gswip_pce_load_microcode(priv); 799 if (err) { 800 dev_err(priv->dev, "writing PCE microcode failed, %i", err); 801 return err; 802 } 803 804 /* Default unknown Broadcast/Multicast/Unicast port maps */ 805 gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP1); 806 gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP2); 807 gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP3); 808 809 /* Deactivate MDIO PHY auto polling. Some PHYs as the AR8030 have an 810 * interoperability problem with this auto polling mechanism because 811 * their status registers think that the link is in a different state 812 * than it actually is. For the AR8030 it has the BMSR_ESTATEN bit set 813 * as well as ESTATUS_1000_TFULL and ESTATUS_1000_XFULL. This makes the 814 * auto polling state machine consider the link being negotiated with 815 * 1Gbit/s. Since the PHY itself is a Fast Ethernet RMII PHY this leads 816 * to the switch port being completely dead (RX and TX are both not 817 * working). 818 * Also with various other PHY / port combinations (PHY11G GPHY, PHY22F 819 * GPHY, external RGMII PEF7071/7072) any traffic would stop. Sometimes 820 * it would work fine for a few minutes to hours and then stop, on 821 * other device it would no traffic could be sent or received at all. 822 * Testing shows that when PHY auto polling is disabled these problems 823 * go away. 824 */ 825 gswip_mdio_w(priv, 0x0, GSWIP_MDIO_MDC_CFG0); 826 827 /* Configure the MDIO Clock 2.5 MHz */ 828 gswip_mdio_mask(priv, 0xff, 0x09, GSWIP_MDIO_MDC_CFG1); 829 830 /* Disable the xMII interface and clear it's isolation bit */ 831 for (i = 0; i < priv->hw_info->max_ports; i++) 832 gswip_mii_mask_cfg(priv, 833 GSWIP_MII_CFG_EN | GSWIP_MII_CFG_ISOLATE, 834 0, i); 835 836 /* enable special tag insertion on cpu port */ 837 gswip_switch_mask(priv, 0, GSWIP_FDMA_PCTRL_STEN, 838 GSWIP_FDMA_PCTRLp(cpu_port)); 839 840 /* accept special tag in ingress direction */ 841 gswip_switch_mask(priv, 0, GSWIP_PCE_PCTRL_0_INGRESS, 842 GSWIP_PCE_PCTRL_0p(cpu_port)); 843 844 gswip_switch_mask(priv, 0, GSWIP_MAC_CTRL_2_MLEN, 845 GSWIP_MAC_CTRL_2p(cpu_port)); 846 gswip_switch_w(priv, VLAN_ETH_FRAME_LEN + 8 + ETH_FCS_LEN, 847 GSWIP_MAC_FLEN); 848 gswip_switch_mask(priv, 0, GSWIP_BM_QUEUE_GCTRL_GL_MOD, 849 GSWIP_BM_QUEUE_GCTRL); 850 851 /* VLAN aware Switching */ 852 gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_VLAN, GSWIP_PCE_GCTRL_0); 853 854 /* Flush MAC Table */ 855 gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_MTFL, GSWIP_PCE_GCTRL_0); 856 857 err = gswip_switch_r_timeout(priv, GSWIP_PCE_GCTRL_0, 858 GSWIP_PCE_GCTRL_0_MTFL); 859 if (err) { 860 dev_err(priv->dev, "MAC flushing didn't finish\n"); 861 return err; 862 } 863 864 gswip_port_enable(ds, cpu_port, NULL); 865 866 ds->configure_vlan_while_not_filtering = false; 867 868 return 0; 869 } 870 871 static enum dsa_tag_protocol gswip_get_tag_protocol(struct dsa_switch *ds, 872 int port, 873 enum dsa_tag_protocol mp) 874 { 875 return DSA_TAG_PROTO_GSWIP; 876 } 877 878 static int gswip_vlan_active_create(struct gswip_priv *priv, 879 struct net_device *bridge, 880 int fid, u16 vid) 881 { 882 struct gswip_pce_table_entry vlan_active = {0,}; 883 unsigned int max_ports = priv->hw_info->max_ports; 884 int idx = -1; 885 int err; 886 int i; 887 888 /* Look for a free slot */ 889 for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { 890 if (!priv->vlans[i].bridge) { 891 idx = i; 892 break; 893 } 894 } 895 896 if (idx == -1) 897 return -ENOSPC; 898 899 if (fid == -1) 900 fid = idx; 901 902 vlan_active.index = idx; 903 vlan_active.table = GSWIP_TABLE_ACTIVE_VLAN; 904 vlan_active.key[0] = vid; 905 vlan_active.val[0] = fid; 906 vlan_active.valid = true; 907 908 err = gswip_pce_table_entry_write(priv, &vlan_active); 909 if (err) { 910 dev_err(priv->dev, "failed to write active VLAN: %d\n", err); 911 return err; 912 } 913 914 priv->vlans[idx].bridge = bridge; 915 priv->vlans[idx].vid = vid; 916 priv->vlans[idx].fid = fid; 917 918 return idx; 919 } 920 921 static int gswip_vlan_active_remove(struct gswip_priv *priv, int idx) 922 { 923 struct gswip_pce_table_entry vlan_active = {0,}; 924 int err; 925 926 vlan_active.index = idx; 927 vlan_active.table = GSWIP_TABLE_ACTIVE_VLAN; 928 vlan_active.valid = false; 929 err = gswip_pce_table_entry_write(priv, &vlan_active); 930 if (err) 931 dev_err(priv->dev, "failed to delete active VLAN: %d\n", err); 932 priv->vlans[idx].bridge = NULL; 933 934 return err; 935 } 936 937 static int gswip_vlan_add_unaware(struct gswip_priv *priv, 938 struct net_device *bridge, int port) 939 { 940 struct gswip_pce_table_entry vlan_mapping = {0,}; 941 unsigned int max_ports = priv->hw_info->max_ports; 942 unsigned int cpu_port = priv->hw_info->cpu_port; 943 bool active_vlan_created = false; 944 int idx = -1; 945 int i; 946 int err; 947 948 /* Check if there is already a page for this bridge */ 949 for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { 950 if (priv->vlans[i].bridge == bridge) { 951 idx = i; 952 break; 953 } 954 } 955 956 /* If this bridge is not programmed yet, add a Active VLAN table 957 * entry in a free slot and prepare the VLAN mapping table entry. 958 */ 959 if (idx == -1) { 960 idx = gswip_vlan_active_create(priv, bridge, -1, 0); 961 if (idx < 0) 962 return idx; 963 active_vlan_created = true; 964 965 vlan_mapping.index = idx; 966 vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; 967 /* VLAN ID byte, maps to the VLAN ID of vlan active table */ 968 vlan_mapping.val[0] = 0; 969 } else { 970 /* Read the existing VLAN mapping entry from the switch */ 971 vlan_mapping.index = idx; 972 vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; 973 err = gswip_pce_table_entry_read(priv, &vlan_mapping); 974 if (err) { 975 dev_err(priv->dev, "failed to read VLAN mapping: %d\n", 976 err); 977 return err; 978 } 979 } 980 981 /* Update the VLAN mapping entry and write it to the switch */ 982 vlan_mapping.val[1] |= BIT(cpu_port); 983 vlan_mapping.val[1] |= BIT(port); 984 err = gswip_pce_table_entry_write(priv, &vlan_mapping); 985 if (err) { 986 dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err); 987 /* In case an Active VLAN was creaetd delete it again */ 988 if (active_vlan_created) 989 gswip_vlan_active_remove(priv, idx); 990 return err; 991 } 992 993 gswip_switch_w(priv, 0, GSWIP_PCE_DEFPVID(port)); 994 return 0; 995 } 996 997 static int gswip_vlan_add_aware(struct gswip_priv *priv, 998 struct net_device *bridge, int port, 999 u16 vid, bool untagged, 1000 bool pvid) 1001 { 1002 struct gswip_pce_table_entry vlan_mapping = {0,}; 1003 unsigned int max_ports = priv->hw_info->max_ports; 1004 unsigned int cpu_port = priv->hw_info->cpu_port; 1005 bool active_vlan_created = false; 1006 int idx = -1; 1007 int fid = -1; 1008 int i; 1009 int err; 1010 1011 /* Check if there is already a page for this bridge */ 1012 for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { 1013 if (priv->vlans[i].bridge == bridge) { 1014 if (fid != -1 && fid != priv->vlans[i].fid) 1015 dev_err(priv->dev, "one bridge with multiple flow ids\n"); 1016 fid = priv->vlans[i].fid; 1017 if (priv->vlans[i].vid == vid) { 1018 idx = i; 1019 break; 1020 } 1021 } 1022 } 1023 1024 /* If this bridge is not programmed yet, add a Active VLAN table 1025 * entry in a free slot and prepare the VLAN mapping table entry. 1026 */ 1027 if (idx == -1) { 1028 idx = gswip_vlan_active_create(priv, bridge, fid, vid); 1029 if (idx < 0) 1030 return idx; 1031 active_vlan_created = true; 1032 1033 vlan_mapping.index = idx; 1034 vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; 1035 /* VLAN ID byte, maps to the VLAN ID of vlan active table */ 1036 vlan_mapping.val[0] = vid; 1037 } else { 1038 /* Read the existing VLAN mapping entry from the switch */ 1039 vlan_mapping.index = idx; 1040 vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; 1041 err = gswip_pce_table_entry_read(priv, &vlan_mapping); 1042 if (err) { 1043 dev_err(priv->dev, "failed to read VLAN mapping: %d\n", 1044 err); 1045 return err; 1046 } 1047 } 1048 1049 vlan_mapping.val[0] = vid; 1050 /* Update the VLAN mapping entry and write it to the switch */ 1051 vlan_mapping.val[1] |= BIT(cpu_port); 1052 vlan_mapping.val[2] |= BIT(cpu_port); 1053 vlan_mapping.val[1] |= BIT(port); 1054 if (untagged) 1055 vlan_mapping.val[2] &= ~BIT(port); 1056 else 1057 vlan_mapping.val[2] |= BIT(port); 1058 err = gswip_pce_table_entry_write(priv, &vlan_mapping); 1059 if (err) { 1060 dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err); 1061 /* In case an Active VLAN was creaetd delete it again */ 1062 if (active_vlan_created) 1063 gswip_vlan_active_remove(priv, idx); 1064 return err; 1065 } 1066 1067 if (pvid) 1068 gswip_switch_w(priv, idx, GSWIP_PCE_DEFPVID(port)); 1069 1070 return 0; 1071 } 1072 1073 static int gswip_vlan_remove(struct gswip_priv *priv, 1074 struct net_device *bridge, int port, 1075 u16 vid, bool pvid, bool vlan_aware) 1076 { 1077 struct gswip_pce_table_entry vlan_mapping = {0,}; 1078 unsigned int max_ports = priv->hw_info->max_ports; 1079 unsigned int cpu_port = priv->hw_info->cpu_port; 1080 int idx = -1; 1081 int i; 1082 int err; 1083 1084 /* Check if there is already a page for this bridge */ 1085 for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { 1086 if (priv->vlans[i].bridge == bridge && 1087 (!vlan_aware || priv->vlans[i].vid == vid)) { 1088 idx = i; 1089 break; 1090 } 1091 } 1092 1093 if (idx == -1) { 1094 dev_err(priv->dev, "bridge to leave does not exists\n"); 1095 return -ENOENT; 1096 } 1097 1098 vlan_mapping.index = idx; 1099 vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; 1100 err = gswip_pce_table_entry_read(priv, &vlan_mapping); 1101 if (err) { 1102 dev_err(priv->dev, "failed to read VLAN mapping: %d\n", err); 1103 return err; 1104 } 1105 1106 vlan_mapping.val[1] &= ~BIT(port); 1107 vlan_mapping.val[2] &= ~BIT(port); 1108 err = gswip_pce_table_entry_write(priv, &vlan_mapping); 1109 if (err) { 1110 dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err); 1111 return err; 1112 } 1113 1114 /* In case all ports are removed from the bridge, remove the VLAN */ 1115 if ((vlan_mapping.val[1] & ~BIT(cpu_port)) == 0) { 1116 err = gswip_vlan_active_remove(priv, idx); 1117 if (err) { 1118 dev_err(priv->dev, "failed to write active VLAN: %d\n", 1119 err); 1120 return err; 1121 } 1122 } 1123 1124 /* GSWIP 2.2 (GRX300) and later program here the VID directly. */ 1125 if (pvid) 1126 gswip_switch_w(priv, 0, GSWIP_PCE_DEFPVID(port)); 1127 1128 return 0; 1129 } 1130 1131 static int gswip_port_bridge_join(struct dsa_switch *ds, int port, 1132 struct net_device *bridge) 1133 { 1134 struct gswip_priv *priv = ds->priv; 1135 int err; 1136 1137 /* When the bridge uses VLAN filtering we have to configure VLAN 1138 * specific bridges. No bridge is configured here. 1139 */ 1140 if (!br_vlan_enabled(bridge)) { 1141 err = gswip_vlan_add_unaware(priv, bridge, port); 1142 if (err) 1143 return err; 1144 priv->port_vlan_filter &= ~BIT(port); 1145 } else { 1146 priv->port_vlan_filter |= BIT(port); 1147 } 1148 return gswip_add_single_port_br(priv, port, false); 1149 } 1150 1151 static void gswip_port_bridge_leave(struct dsa_switch *ds, int port, 1152 struct net_device *bridge) 1153 { 1154 struct gswip_priv *priv = ds->priv; 1155 1156 gswip_add_single_port_br(priv, port, true); 1157 1158 /* When the bridge uses VLAN filtering we have to configure VLAN 1159 * specific bridges. No bridge is configured here. 1160 */ 1161 if (!br_vlan_enabled(bridge)) 1162 gswip_vlan_remove(priv, bridge, port, 0, true, false); 1163 } 1164 1165 static int gswip_port_vlan_prepare(struct dsa_switch *ds, int port, 1166 const struct switchdev_obj_port_vlan *vlan, 1167 struct netlink_ext_ack *extack) 1168 { 1169 struct gswip_priv *priv = ds->priv; 1170 struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev; 1171 unsigned int max_ports = priv->hw_info->max_ports; 1172 int pos = max_ports; 1173 int i, idx = -1; 1174 1175 /* We only support VLAN filtering on bridges */ 1176 if (!dsa_is_cpu_port(ds, port) && !bridge) 1177 return -EOPNOTSUPP; 1178 1179 /* Check if there is already a page for this VLAN */ 1180 for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { 1181 if (priv->vlans[i].bridge == bridge && 1182 priv->vlans[i].vid == vlan->vid) { 1183 idx = i; 1184 break; 1185 } 1186 } 1187 1188 /* If this VLAN is not programmed yet, we have to reserve 1189 * one entry in the VLAN table. Make sure we start at the 1190 * next position round. 1191 */ 1192 if (idx == -1) { 1193 /* Look for a free slot */ 1194 for (; pos < ARRAY_SIZE(priv->vlans); pos++) { 1195 if (!priv->vlans[pos].bridge) { 1196 idx = pos; 1197 pos++; 1198 break; 1199 } 1200 } 1201 1202 if (idx == -1) { 1203 NL_SET_ERR_MSG_MOD(extack, "No slot in VLAN table"); 1204 return -ENOSPC; 1205 } 1206 } 1207 1208 return 0; 1209 } 1210 1211 static int gswip_port_vlan_add(struct dsa_switch *ds, int port, 1212 const struct switchdev_obj_port_vlan *vlan, 1213 struct netlink_ext_ack *extack) 1214 { 1215 struct gswip_priv *priv = ds->priv; 1216 struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev; 1217 bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED; 1218 bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID; 1219 int err; 1220 1221 err = gswip_port_vlan_prepare(ds, port, vlan, extack); 1222 if (err) 1223 return err; 1224 1225 /* We have to receive all packets on the CPU port and should not 1226 * do any VLAN filtering here. This is also called with bridge 1227 * NULL and then we do not know for which bridge to configure 1228 * this. 1229 */ 1230 if (dsa_is_cpu_port(ds, port)) 1231 return 0; 1232 1233 return gswip_vlan_add_aware(priv, bridge, port, vlan->vid, 1234 untagged, pvid); 1235 } 1236 1237 static int gswip_port_vlan_del(struct dsa_switch *ds, int port, 1238 const struct switchdev_obj_port_vlan *vlan) 1239 { 1240 struct gswip_priv *priv = ds->priv; 1241 struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev; 1242 bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID; 1243 1244 /* We have to receive all packets on the CPU port and should not 1245 * do any VLAN filtering here. This is also called with bridge 1246 * NULL and then we do not know for which bridge to configure 1247 * this. 1248 */ 1249 if (dsa_is_cpu_port(ds, port)) 1250 return 0; 1251 1252 return gswip_vlan_remove(priv, bridge, port, vlan->vid, pvid, true); 1253 } 1254 1255 static void gswip_port_fast_age(struct dsa_switch *ds, int port) 1256 { 1257 struct gswip_priv *priv = ds->priv; 1258 struct gswip_pce_table_entry mac_bridge = {0,}; 1259 int i; 1260 int err; 1261 1262 for (i = 0; i < 2048; i++) { 1263 mac_bridge.table = GSWIP_TABLE_MAC_BRIDGE; 1264 mac_bridge.index = i; 1265 1266 err = gswip_pce_table_entry_read(priv, &mac_bridge); 1267 if (err) { 1268 dev_err(priv->dev, "failed to read mac bridge: %d\n", 1269 err); 1270 return; 1271 } 1272 1273 if (!mac_bridge.valid) 1274 continue; 1275 1276 if (mac_bridge.val[1] & GSWIP_TABLE_MAC_BRIDGE_STATIC) 1277 continue; 1278 1279 if (((mac_bridge.val[0] & GENMASK(7, 4)) >> 4) != port) 1280 continue; 1281 1282 mac_bridge.valid = false; 1283 err = gswip_pce_table_entry_write(priv, &mac_bridge); 1284 if (err) { 1285 dev_err(priv->dev, "failed to write mac bridge: %d\n", 1286 err); 1287 return; 1288 } 1289 } 1290 } 1291 1292 static void gswip_port_stp_state_set(struct dsa_switch *ds, int port, u8 state) 1293 { 1294 struct gswip_priv *priv = ds->priv; 1295 u32 stp_state; 1296 1297 switch (state) { 1298 case BR_STATE_DISABLED: 1299 gswip_switch_mask(priv, GSWIP_SDMA_PCTRL_EN, 0, 1300 GSWIP_SDMA_PCTRLp(port)); 1301 return; 1302 case BR_STATE_BLOCKING: 1303 case BR_STATE_LISTENING: 1304 stp_state = GSWIP_PCE_PCTRL_0_PSTATE_LISTEN; 1305 break; 1306 case BR_STATE_LEARNING: 1307 stp_state = GSWIP_PCE_PCTRL_0_PSTATE_LEARNING; 1308 break; 1309 case BR_STATE_FORWARDING: 1310 stp_state = GSWIP_PCE_PCTRL_0_PSTATE_FORWARDING; 1311 break; 1312 default: 1313 dev_err(priv->dev, "invalid STP state: %d\n", state); 1314 return; 1315 } 1316 1317 gswip_switch_mask(priv, 0, GSWIP_SDMA_PCTRL_EN, 1318 GSWIP_SDMA_PCTRLp(port)); 1319 gswip_switch_mask(priv, GSWIP_PCE_PCTRL_0_PSTATE_MASK, stp_state, 1320 GSWIP_PCE_PCTRL_0p(port)); 1321 } 1322 1323 static int gswip_port_fdb(struct dsa_switch *ds, int port, 1324 const unsigned char *addr, u16 vid, bool add) 1325 { 1326 struct gswip_priv *priv = ds->priv; 1327 struct net_device *bridge = dsa_to_port(ds, port)->bridge_dev; 1328 struct gswip_pce_table_entry mac_bridge = {0,}; 1329 unsigned int cpu_port = priv->hw_info->cpu_port; 1330 int fid = -1; 1331 int i; 1332 int err; 1333 1334 if (!bridge) 1335 return -EINVAL; 1336 1337 for (i = cpu_port; i < ARRAY_SIZE(priv->vlans); i++) { 1338 if (priv->vlans[i].bridge == bridge) { 1339 fid = priv->vlans[i].fid; 1340 break; 1341 } 1342 } 1343 1344 if (fid == -1) { 1345 dev_err(priv->dev, "Port not part of a bridge\n"); 1346 return -EINVAL; 1347 } 1348 1349 mac_bridge.table = GSWIP_TABLE_MAC_BRIDGE; 1350 mac_bridge.key_mode = true; 1351 mac_bridge.key[0] = addr[5] | (addr[4] << 8); 1352 mac_bridge.key[1] = addr[3] | (addr[2] << 8); 1353 mac_bridge.key[2] = addr[1] | (addr[0] << 8); 1354 mac_bridge.key[3] = fid; 1355 mac_bridge.val[0] = add ? BIT(port) : 0; /* port map */ 1356 mac_bridge.val[1] = GSWIP_TABLE_MAC_BRIDGE_STATIC; 1357 mac_bridge.valid = add; 1358 1359 err = gswip_pce_table_entry_write(priv, &mac_bridge); 1360 if (err) 1361 dev_err(priv->dev, "failed to write mac bridge: %d\n", err); 1362 1363 return err; 1364 } 1365 1366 static int gswip_port_fdb_add(struct dsa_switch *ds, int port, 1367 const unsigned char *addr, u16 vid) 1368 { 1369 return gswip_port_fdb(ds, port, addr, vid, true); 1370 } 1371 1372 static int gswip_port_fdb_del(struct dsa_switch *ds, int port, 1373 const unsigned char *addr, u16 vid) 1374 { 1375 return gswip_port_fdb(ds, port, addr, vid, false); 1376 } 1377 1378 static int gswip_port_fdb_dump(struct dsa_switch *ds, int port, 1379 dsa_fdb_dump_cb_t *cb, void *data) 1380 { 1381 struct gswip_priv *priv = ds->priv; 1382 struct gswip_pce_table_entry mac_bridge = {0,}; 1383 unsigned char addr[6]; 1384 int i; 1385 int err; 1386 1387 for (i = 0; i < 2048; i++) { 1388 mac_bridge.table = GSWIP_TABLE_MAC_BRIDGE; 1389 mac_bridge.index = i; 1390 1391 err = gswip_pce_table_entry_read(priv, &mac_bridge); 1392 if (err) { 1393 dev_err(priv->dev, "failed to write mac bridge: %d\n", 1394 err); 1395 return err; 1396 } 1397 1398 if (!mac_bridge.valid) 1399 continue; 1400 1401 addr[5] = mac_bridge.key[0] & 0xff; 1402 addr[4] = (mac_bridge.key[0] >> 8) & 0xff; 1403 addr[3] = mac_bridge.key[1] & 0xff; 1404 addr[2] = (mac_bridge.key[1] >> 8) & 0xff; 1405 addr[1] = mac_bridge.key[2] & 0xff; 1406 addr[0] = (mac_bridge.key[2] >> 8) & 0xff; 1407 if (mac_bridge.val[1] & GSWIP_TABLE_MAC_BRIDGE_STATIC) { 1408 if (mac_bridge.val[0] & BIT(port)) { 1409 err = cb(addr, 0, true, data); 1410 if (err) 1411 return err; 1412 } 1413 } else { 1414 if (((mac_bridge.val[0] & GENMASK(7, 4)) >> 4) == port) { 1415 err = cb(addr, 0, false, data); 1416 if (err) 1417 return err; 1418 } 1419 } 1420 } 1421 return 0; 1422 } 1423 1424 static void gswip_phylink_set_capab(unsigned long *supported, 1425 struct phylink_link_state *state) 1426 { 1427 __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, }; 1428 1429 /* Allow all the expected bits */ 1430 phylink_set(mask, Autoneg); 1431 phylink_set_port_modes(mask); 1432 phylink_set(mask, Pause); 1433 phylink_set(mask, Asym_Pause); 1434 1435 /* With the exclusion of MII, Reverse MII and Reduced MII, we 1436 * support Gigabit, including Half duplex 1437 */ 1438 if (state->interface != PHY_INTERFACE_MODE_MII && 1439 state->interface != PHY_INTERFACE_MODE_REVMII && 1440 state->interface != PHY_INTERFACE_MODE_RMII) { 1441 phylink_set(mask, 1000baseT_Full); 1442 phylink_set(mask, 1000baseT_Half); 1443 } 1444 1445 phylink_set(mask, 10baseT_Half); 1446 phylink_set(mask, 10baseT_Full); 1447 phylink_set(mask, 100baseT_Half); 1448 phylink_set(mask, 100baseT_Full); 1449 1450 bitmap_and(supported, supported, mask, 1451 __ETHTOOL_LINK_MODE_MASK_NBITS); 1452 bitmap_and(state->advertising, state->advertising, mask, 1453 __ETHTOOL_LINK_MODE_MASK_NBITS); 1454 } 1455 1456 static void gswip_xrx200_phylink_validate(struct dsa_switch *ds, int port, 1457 unsigned long *supported, 1458 struct phylink_link_state *state) 1459 { 1460 switch (port) { 1461 case 0: 1462 case 1: 1463 if (!phy_interface_mode_is_rgmii(state->interface) && 1464 state->interface != PHY_INTERFACE_MODE_MII && 1465 state->interface != PHY_INTERFACE_MODE_REVMII && 1466 state->interface != PHY_INTERFACE_MODE_RMII) 1467 goto unsupported; 1468 break; 1469 case 2: 1470 case 3: 1471 case 4: 1472 if (state->interface != PHY_INTERFACE_MODE_INTERNAL) 1473 goto unsupported; 1474 break; 1475 case 5: 1476 if (!phy_interface_mode_is_rgmii(state->interface) && 1477 state->interface != PHY_INTERFACE_MODE_INTERNAL) 1478 goto unsupported; 1479 break; 1480 default: 1481 bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS); 1482 dev_err(ds->dev, "Unsupported port: %i\n", port); 1483 return; 1484 } 1485 1486 gswip_phylink_set_capab(supported, state); 1487 1488 return; 1489 1490 unsupported: 1491 bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS); 1492 dev_err(ds->dev, "Unsupported interface '%s' for port %d\n", 1493 phy_modes(state->interface), port); 1494 } 1495 1496 static void gswip_xrx300_phylink_validate(struct dsa_switch *ds, int port, 1497 unsigned long *supported, 1498 struct phylink_link_state *state) 1499 { 1500 switch (port) { 1501 case 0: 1502 if (!phy_interface_mode_is_rgmii(state->interface) && 1503 state->interface != PHY_INTERFACE_MODE_GMII && 1504 state->interface != PHY_INTERFACE_MODE_RMII) 1505 goto unsupported; 1506 break; 1507 case 1: 1508 case 2: 1509 case 3: 1510 case 4: 1511 if (state->interface != PHY_INTERFACE_MODE_INTERNAL) 1512 goto unsupported; 1513 break; 1514 case 5: 1515 if (!phy_interface_mode_is_rgmii(state->interface) && 1516 state->interface != PHY_INTERFACE_MODE_INTERNAL && 1517 state->interface != PHY_INTERFACE_MODE_RMII) 1518 goto unsupported; 1519 break; 1520 default: 1521 bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS); 1522 dev_err(ds->dev, "Unsupported port: %i\n", port); 1523 return; 1524 } 1525 1526 gswip_phylink_set_capab(supported, state); 1527 1528 return; 1529 1530 unsupported: 1531 bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS); 1532 dev_err(ds->dev, "Unsupported interface '%s' for port %d\n", 1533 phy_modes(state->interface), port); 1534 } 1535 1536 static void gswip_port_set_link(struct gswip_priv *priv, int port, bool link) 1537 { 1538 u32 mdio_phy; 1539 1540 if (link) 1541 mdio_phy = GSWIP_MDIO_PHY_LINK_UP; 1542 else 1543 mdio_phy = GSWIP_MDIO_PHY_LINK_DOWN; 1544 1545 gswip_mdio_mask(priv, GSWIP_MDIO_PHY_LINK_MASK, mdio_phy, 1546 GSWIP_MDIO_PHYp(port)); 1547 } 1548 1549 static void gswip_port_set_speed(struct gswip_priv *priv, int port, int speed, 1550 phy_interface_t interface) 1551 { 1552 u32 mdio_phy = 0, mii_cfg = 0, mac_ctrl_0 = 0; 1553 1554 switch (speed) { 1555 case SPEED_10: 1556 mdio_phy = GSWIP_MDIO_PHY_SPEED_M10; 1557 1558 if (interface == PHY_INTERFACE_MODE_RMII) 1559 mii_cfg = GSWIP_MII_CFG_RATE_M50; 1560 else 1561 mii_cfg = GSWIP_MII_CFG_RATE_M2P5; 1562 1563 mac_ctrl_0 = GSWIP_MAC_CTRL_0_GMII_MII; 1564 break; 1565 1566 case SPEED_100: 1567 mdio_phy = GSWIP_MDIO_PHY_SPEED_M100; 1568 1569 if (interface == PHY_INTERFACE_MODE_RMII) 1570 mii_cfg = GSWIP_MII_CFG_RATE_M50; 1571 else 1572 mii_cfg = GSWIP_MII_CFG_RATE_M25; 1573 1574 mac_ctrl_0 = GSWIP_MAC_CTRL_0_GMII_MII; 1575 break; 1576 1577 case SPEED_1000: 1578 mdio_phy = GSWIP_MDIO_PHY_SPEED_G1; 1579 1580 mii_cfg = GSWIP_MII_CFG_RATE_M125; 1581 1582 mac_ctrl_0 = GSWIP_MAC_CTRL_0_GMII_RGMII; 1583 break; 1584 } 1585 1586 gswip_mdio_mask(priv, GSWIP_MDIO_PHY_SPEED_MASK, mdio_phy, 1587 GSWIP_MDIO_PHYp(port)); 1588 gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_RATE_MASK, mii_cfg, port); 1589 gswip_switch_mask(priv, GSWIP_MAC_CTRL_0_GMII_MASK, mac_ctrl_0, 1590 GSWIP_MAC_CTRL_0p(port)); 1591 } 1592 1593 static void gswip_port_set_duplex(struct gswip_priv *priv, int port, int duplex) 1594 { 1595 u32 mac_ctrl_0, mdio_phy; 1596 1597 if (duplex == DUPLEX_FULL) { 1598 mac_ctrl_0 = GSWIP_MAC_CTRL_0_FDUP_EN; 1599 mdio_phy = GSWIP_MDIO_PHY_FDUP_EN; 1600 } else { 1601 mac_ctrl_0 = GSWIP_MAC_CTRL_0_FDUP_DIS; 1602 mdio_phy = GSWIP_MDIO_PHY_FDUP_DIS; 1603 } 1604 1605 gswip_switch_mask(priv, GSWIP_MAC_CTRL_0_FDUP_MASK, mac_ctrl_0, 1606 GSWIP_MAC_CTRL_0p(port)); 1607 gswip_mdio_mask(priv, GSWIP_MDIO_PHY_FDUP_MASK, mdio_phy, 1608 GSWIP_MDIO_PHYp(port)); 1609 } 1610 1611 static void gswip_port_set_pause(struct gswip_priv *priv, int port, 1612 bool tx_pause, bool rx_pause) 1613 { 1614 u32 mac_ctrl_0, mdio_phy; 1615 1616 if (tx_pause && rx_pause) { 1617 mac_ctrl_0 = GSWIP_MAC_CTRL_0_FCON_RXTX; 1618 mdio_phy = GSWIP_MDIO_PHY_FCONTX_EN | 1619 GSWIP_MDIO_PHY_FCONRX_EN; 1620 } else if (tx_pause) { 1621 mac_ctrl_0 = GSWIP_MAC_CTRL_0_FCON_TX; 1622 mdio_phy = GSWIP_MDIO_PHY_FCONTX_EN | 1623 GSWIP_MDIO_PHY_FCONRX_DIS; 1624 } else if (rx_pause) { 1625 mac_ctrl_0 = GSWIP_MAC_CTRL_0_FCON_RX; 1626 mdio_phy = GSWIP_MDIO_PHY_FCONTX_DIS | 1627 GSWIP_MDIO_PHY_FCONRX_EN; 1628 } else { 1629 mac_ctrl_0 = GSWIP_MAC_CTRL_0_FCON_NONE; 1630 mdio_phy = GSWIP_MDIO_PHY_FCONTX_DIS | 1631 GSWIP_MDIO_PHY_FCONRX_DIS; 1632 } 1633 1634 gswip_switch_mask(priv, GSWIP_MAC_CTRL_0_FCON_MASK, 1635 mac_ctrl_0, GSWIP_MAC_CTRL_0p(port)); 1636 gswip_mdio_mask(priv, 1637 GSWIP_MDIO_PHY_FCONTX_MASK | 1638 GSWIP_MDIO_PHY_FCONRX_MASK, 1639 mdio_phy, GSWIP_MDIO_PHYp(port)); 1640 } 1641 1642 static void gswip_phylink_mac_config(struct dsa_switch *ds, int port, 1643 unsigned int mode, 1644 const struct phylink_link_state *state) 1645 { 1646 struct gswip_priv *priv = ds->priv; 1647 u32 miicfg = 0; 1648 1649 miicfg |= GSWIP_MII_CFG_LDCLKDIS; 1650 1651 switch (state->interface) { 1652 case PHY_INTERFACE_MODE_MII: 1653 case PHY_INTERFACE_MODE_INTERNAL: 1654 miicfg |= GSWIP_MII_CFG_MODE_MIIM; 1655 break; 1656 case PHY_INTERFACE_MODE_REVMII: 1657 miicfg |= GSWIP_MII_CFG_MODE_MIIP; 1658 break; 1659 case PHY_INTERFACE_MODE_RMII: 1660 miicfg |= GSWIP_MII_CFG_MODE_RMIIM; 1661 1662 /* Configure the RMII clock as output: */ 1663 miicfg |= GSWIP_MII_CFG_RMII_CLK; 1664 break; 1665 case PHY_INTERFACE_MODE_RGMII: 1666 case PHY_INTERFACE_MODE_RGMII_ID: 1667 case PHY_INTERFACE_MODE_RGMII_RXID: 1668 case PHY_INTERFACE_MODE_RGMII_TXID: 1669 miicfg |= GSWIP_MII_CFG_MODE_RGMII; 1670 break; 1671 case PHY_INTERFACE_MODE_GMII: 1672 miicfg |= GSWIP_MII_CFG_MODE_GMII; 1673 break; 1674 default: 1675 dev_err(ds->dev, 1676 "Unsupported interface: %d\n", state->interface); 1677 return; 1678 } 1679 1680 gswip_mii_mask_cfg(priv, 1681 GSWIP_MII_CFG_MODE_MASK | GSWIP_MII_CFG_RMII_CLK | 1682 GSWIP_MII_CFG_RGMII_IBS | GSWIP_MII_CFG_LDCLKDIS, 1683 miicfg, port); 1684 1685 switch (state->interface) { 1686 case PHY_INTERFACE_MODE_RGMII_ID: 1687 gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_TXDLY_MASK | 1688 GSWIP_MII_PCDU_RXDLY_MASK, 0, port); 1689 break; 1690 case PHY_INTERFACE_MODE_RGMII_RXID: 1691 gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_RXDLY_MASK, 0, port); 1692 break; 1693 case PHY_INTERFACE_MODE_RGMII_TXID: 1694 gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_TXDLY_MASK, 0, port); 1695 break; 1696 default: 1697 break; 1698 } 1699 } 1700 1701 static void gswip_phylink_mac_link_down(struct dsa_switch *ds, int port, 1702 unsigned int mode, 1703 phy_interface_t interface) 1704 { 1705 struct gswip_priv *priv = ds->priv; 1706 1707 gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, port); 1708 1709 if (!dsa_is_cpu_port(ds, port)) 1710 gswip_port_set_link(priv, port, false); 1711 } 1712 1713 static void gswip_phylink_mac_link_up(struct dsa_switch *ds, int port, 1714 unsigned int mode, 1715 phy_interface_t interface, 1716 struct phy_device *phydev, 1717 int speed, int duplex, 1718 bool tx_pause, bool rx_pause) 1719 { 1720 struct gswip_priv *priv = ds->priv; 1721 1722 if (!dsa_is_cpu_port(ds, port)) { 1723 gswip_port_set_link(priv, port, true); 1724 gswip_port_set_speed(priv, port, speed, interface); 1725 gswip_port_set_duplex(priv, port, duplex); 1726 gswip_port_set_pause(priv, port, tx_pause, rx_pause); 1727 } 1728 1729 gswip_mii_mask_cfg(priv, 0, GSWIP_MII_CFG_EN, port); 1730 } 1731 1732 static void gswip_get_strings(struct dsa_switch *ds, int port, u32 stringset, 1733 uint8_t *data) 1734 { 1735 int i; 1736 1737 if (stringset != ETH_SS_STATS) 1738 return; 1739 1740 for (i = 0; i < ARRAY_SIZE(gswip_rmon_cnt); i++) 1741 strncpy(data + i * ETH_GSTRING_LEN, gswip_rmon_cnt[i].name, 1742 ETH_GSTRING_LEN); 1743 } 1744 1745 static u32 gswip_bcm_ram_entry_read(struct gswip_priv *priv, u32 table, 1746 u32 index) 1747 { 1748 u32 result; 1749 int err; 1750 1751 gswip_switch_w(priv, index, GSWIP_BM_RAM_ADDR); 1752 gswip_switch_mask(priv, GSWIP_BM_RAM_CTRL_ADDR_MASK | 1753 GSWIP_BM_RAM_CTRL_OPMOD, 1754 table | GSWIP_BM_RAM_CTRL_BAS, 1755 GSWIP_BM_RAM_CTRL); 1756 1757 err = gswip_switch_r_timeout(priv, GSWIP_BM_RAM_CTRL, 1758 GSWIP_BM_RAM_CTRL_BAS); 1759 if (err) { 1760 dev_err(priv->dev, "timeout while reading table: %u, index: %u", 1761 table, index); 1762 return 0; 1763 } 1764 1765 result = gswip_switch_r(priv, GSWIP_BM_RAM_VAL(0)); 1766 result |= gswip_switch_r(priv, GSWIP_BM_RAM_VAL(1)) << 16; 1767 1768 return result; 1769 } 1770 1771 static void gswip_get_ethtool_stats(struct dsa_switch *ds, int port, 1772 uint64_t *data) 1773 { 1774 struct gswip_priv *priv = ds->priv; 1775 const struct gswip_rmon_cnt_desc *rmon_cnt; 1776 int i; 1777 u64 high; 1778 1779 for (i = 0; i < ARRAY_SIZE(gswip_rmon_cnt); i++) { 1780 rmon_cnt = &gswip_rmon_cnt[i]; 1781 1782 data[i] = gswip_bcm_ram_entry_read(priv, port, 1783 rmon_cnt->offset); 1784 if (rmon_cnt->size == 2) { 1785 high = gswip_bcm_ram_entry_read(priv, port, 1786 rmon_cnt->offset + 1); 1787 data[i] |= high << 32; 1788 } 1789 } 1790 } 1791 1792 static int gswip_get_sset_count(struct dsa_switch *ds, int port, int sset) 1793 { 1794 if (sset != ETH_SS_STATS) 1795 return 0; 1796 1797 return ARRAY_SIZE(gswip_rmon_cnt); 1798 } 1799 1800 static const struct dsa_switch_ops gswip_xrx200_switch_ops = { 1801 .get_tag_protocol = gswip_get_tag_protocol, 1802 .setup = gswip_setup, 1803 .port_enable = gswip_port_enable, 1804 .port_disable = gswip_port_disable, 1805 .port_bridge_join = gswip_port_bridge_join, 1806 .port_bridge_leave = gswip_port_bridge_leave, 1807 .port_fast_age = gswip_port_fast_age, 1808 .port_vlan_filtering = gswip_port_vlan_filtering, 1809 .port_vlan_add = gswip_port_vlan_add, 1810 .port_vlan_del = gswip_port_vlan_del, 1811 .port_stp_state_set = gswip_port_stp_state_set, 1812 .port_fdb_add = gswip_port_fdb_add, 1813 .port_fdb_del = gswip_port_fdb_del, 1814 .port_fdb_dump = gswip_port_fdb_dump, 1815 .phylink_validate = gswip_xrx200_phylink_validate, 1816 .phylink_mac_config = gswip_phylink_mac_config, 1817 .phylink_mac_link_down = gswip_phylink_mac_link_down, 1818 .phylink_mac_link_up = gswip_phylink_mac_link_up, 1819 .get_strings = gswip_get_strings, 1820 .get_ethtool_stats = gswip_get_ethtool_stats, 1821 .get_sset_count = gswip_get_sset_count, 1822 }; 1823 1824 static const struct dsa_switch_ops gswip_xrx300_switch_ops = { 1825 .get_tag_protocol = gswip_get_tag_protocol, 1826 .setup = gswip_setup, 1827 .port_enable = gswip_port_enable, 1828 .port_disable = gswip_port_disable, 1829 .port_bridge_join = gswip_port_bridge_join, 1830 .port_bridge_leave = gswip_port_bridge_leave, 1831 .port_fast_age = gswip_port_fast_age, 1832 .port_vlan_filtering = gswip_port_vlan_filtering, 1833 .port_vlan_add = gswip_port_vlan_add, 1834 .port_vlan_del = gswip_port_vlan_del, 1835 .port_stp_state_set = gswip_port_stp_state_set, 1836 .port_fdb_add = gswip_port_fdb_add, 1837 .port_fdb_del = gswip_port_fdb_del, 1838 .port_fdb_dump = gswip_port_fdb_dump, 1839 .phylink_validate = gswip_xrx300_phylink_validate, 1840 .phylink_mac_config = gswip_phylink_mac_config, 1841 .phylink_mac_link_down = gswip_phylink_mac_link_down, 1842 .phylink_mac_link_up = gswip_phylink_mac_link_up, 1843 .get_strings = gswip_get_strings, 1844 .get_ethtool_stats = gswip_get_ethtool_stats, 1845 .get_sset_count = gswip_get_sset_count, 1846 }; 1847 1848 static const struct xway_gphy_match_data xrx200a1x_gphy_data = { 1849 .fe_firmware_name = "lantiq/xrx200_phy22f_a14.bin", 1850 .ge_firmware_name = "lantiq/xrx200_phy11g_a14.bin", 1851 }; 1852 1853 static const struct xway_gphy_match_data xrx200a2x_gphy_data = { 1854 .fe_firmware_name = "lantiq/xrx200_phy22f_a22.bin", 1855 .ge_firmware_name = "lantiq/xrx200_phy11g_a22.bin", 1856 }; 1857 1858 static const struct xway_gphy_match_data xrx300_gphy_data = { 1859 .fe_firmware_name = "lantiq/xrx300_phy22f_a21.bin", 1860 .ge_firmware_name = "lantiq/xrx300_phy11g_a21.bin", 1861 }; 1862 1863 static const struct of_device_id xway_gphy_match[] = { 1864 { .compatible = "lantiq,xrx200-gphy-fw", .data = NULL }, 1865 { .compatible = "lantiq,xrx200a1x-gphy-fw", .data = &xrx200a1x_gphy_data }, 1866 { .compatible = "lantiq,xrx200a2x-gphy-fw", .data = &xrx200a2x_gphy_data }, 1867 { .compatible = "lantiq,xrx300-gphy-fw", .data = &xrx300_gphy_data }, 1868 { .compatible = "lantiq,xrx330-gphy-fw", .data = &xrx300_gphy_data }, 1869 {}, 1870 }; 1871 1872 static int gswip_gphy_fw_load(struct gswip_priv *priv, struct gswip_gphy_fw *gphy_fw) 1873 { 1874 struct device *dev = priv->dev; 1875 const struct firmware *fw; 1876 void *fw_addr; 1877 dma_addr_t dma_addr; 1878 dma_addr_t dev_addr; 1879 size_t size; 1880 int ret; 1881 1882 ret = clk_prepare_enable(gphy_fw->clk_gate); 1883 if (ret) 1884 return ret; 1885 1886 reset_control_assert(gphy_fw->reset); 1887 1888 /* The vendor BSP uses a 200ms delay after asserting the reset line. 1889 * Without this some users are observing that the PHY is not coming up 1890 * on the MDIO bus. 1891 */ 1892 msleep(200); 1893 1894 ret = request_firmware(&fw, gphy_fw->fw_name, dev); 1895 if (ret) { 1896 dev_err(dev, "failed to load firmware: %s, error: %i\n", 1897 gphy_fw->fw_name, ret); 1898 return ret; 1899 } 1900 1901 /* GPHY cores need the firmware code in a persistent and contiguous 1902 * memory area with a 16 kB boundary aligned start address. 1903 */ 1904 size = fw->size + XRX200_GPHY_FW_ALIGN; 1905 1906 fw_addr = dmam_alloc_coherent(dev, size, &dma_addr, GFP_KERNEL); 1907 if (fw_addr) { 1908 fw_addr = PTR_ALIGN(fw_addr, XRX200_GPHY_FW_ALIGN); 1909 dev_addr = ALIGN(dma_addr, XRX200_GPHY_FW_ALIGN); 1910 memcpy(fw_addr, fw->data, fw->size); 1911 } else { 1912 dev_err(dev, "failed to alloc firmware memory\n"); 1913 release_firmware(fw); 1914 return -ENOMEM; 1915 } 1916 1917 release_firmware(fw); 1918 1919 ret = regmap_write(priv->rcu_regmap, gphy_fw->fw_addr_offset, dev_addr); 1920 if (ret) 1921 return ret; 1922 1923 reset_control_deassert(gphy_fw->reset); 1924 1925 return ret; 1926 } 1927 1928 static int gswip_gphy_fw_probe(struct gswip_priv *priv, 1929 struct gswip_gphy_fw *gphy_fw, 1930 struct device_node *gphy_fw_np, int i) 1931 { 1932 struct device *dev = priv->dev; 1933 u32 gphy_mode; 1934 int ret; 1935 char gphyname[10]; 1936 1937 snprintf(gphyname, sizeof(gphyname), "gphy%d", i); 1938 1939 gphy_fw->clk_gate = devm_clk_get(dev, gphyname); 1940 if (IS_ERR(gphy_fw->clk_gate)) { 1941 dev_err(dev, "Failed to lookup gate clock\n"); 1942 return PTR_ERR(gphy_fw->clk_gate); 1943 } 1944 1945 ret = of_property_read_u32(gphy_fw_np, "reg", &gphy_fw->fw_addr_offset); 1946 if (ret) 1947 return ret; 1948 1949 ret = of_property_read_u32(gphy_fw_np, "lantiq,gphy-mode", &gphy_mode); 1950 /* Default to GE mode */ 1951 if (ret) 1952 gphy_mode = GPHY_MODE_GE; 1953 1954 switch (gphy_mode) { 1955 case GPHY_MODE_FE: 1956 gphy_fw->fw_name = priv->gphy_fw_name_cfg->fe_firmware_name; 1957 break; 1958 case GPHY_MODE_GE: 1959 gphy_fw->fw_name = priv->gphy_fw_name_cfg->ge_firmware_name; 1960 break; 1961 default: 1962 dev_err(dev, "Unknown GPHY mode %d\n", gphy_mode); 1963 return -EINVAL; 1964 } 1965 1966 gphy_fw->reset = of_reset_control_array_get_exclusive(gphy_fw_np); 1967 if (IS_ERR(gphy_fw->reset)) { 1968 if (PTR_ERR(gphy_fw->reset) != -EPROBE_DEFER) 1969 dev_err(dev, "Failed to lookup gphy reset\n"); 1970 return PTR_ERR(gphy_fw->reset); 1971 } 1972 1973 return gswip_gphy_fw_load(priv, gphy_fw); 1974 } 1975 1976 static void gswip_gphy_fw_remove(struct gswip_priv *priv, 1977 struct gswip_gphy_fw *gphy_fw) 1978 { 1979 int ret; 1980 1981 /* check if the device was fully probed */ 1982 if (!gphy_fw->fw_name) 1983 return; 1984 1985 ret = regmap_write(priv->rcu_regmap, gphy_fw->fw_addr_offset, 0); 1986 if (ret) 1987 dev_err(priv->dev, "can not reset GPHY FW pointer"); 1988 1989 clk_disable_unprepare(gphy_fw->clk_gate); 1990 1991 reset_control_put(gphy_fw->reset); 1992 } 1993 1994 static int gswip_gphy_fw_list(struct gswip_priv *priv, 1995 struct device_node *gphy_fw_list_np, u32 version) 1996 { 1997 struct device *dev = priv->dev; 1998 struct device_node *gphy_fw_np; 1999 const struct of_device_id *match; 2000 int err; 2001 int i = 0; 2002 2003 /* The VRX200 rev 1.1 uses the GSWIP 2.0 and needs the older 2004 * GPHY firmware. The VRX200 rev 1.2 uses the GSWIP 2.1 and also 2005 * needs a different GPHY firmware. 2006 */ 2007 if (of_device_is_compatible(gphy_fw_list_np, "lantiq,xrx200-gphy-fw")) { 2008 switch (version) { 2009 case GSWIP_VERSION_2_0: 2010 priv->gphy_fw_name_cfg = &xrx200a1x_gphy_data; 2011 break; 2012 case GSWIP_VERSION_2_1: 2013 priv->gphy_fw_name_cfg = &xrx200a2x_gphy_data; 2014 break; 2015 default: 2016 dev_err(dev, "unknown GSWIP version: 0x%x", version); 2017 return -ENOENT; 2018 } 2019 } 2020 2021 match = of_match_node(xway_gphy_match, gphy_fw_list_np); 2022 if (match && match->data) 2023 priv->gphy_fw_name_cfg = match->data; 2024 2025 if (!priv->gphy_fw_name_cfg) { 2026 dev_err(dev, "GPHY compatible type not supported"); 2027 return -ENOENT; 2028 } 2029 2030 priv->num_gphy_fw = of_get_available_child_count(gphy_fw_list_np); 2031 if (!priv->num_gphy_fw) 2032 return -ENOENT; 2033 2034 priv->rcu_regmap = syscon_regmap_lookup_by_phandle(gphy_fw_list_np, 2035 "lantiq,rcu"); 2036 if (IS_ERR(priv->rcu_regmap)) 2037 return PTR_ERR(priv->rcu_regmap); 2038 2039 priv->gphy_fw = devm_kmalloc_array(dev, priv->num_gphy_fw, 2040 sizeof(*priv->gphy_fw), 2041 GFP_KERNEL | __GFP_ZERO); 2042 if (!priv->gphy_fw) 2043 return -ENOMEM; 2044 2045 for_each_available_child_of_node(gphy_fw_list_np, gphy_fw_np) { 2046 err = gswip_gphy_fw_probe(priv, &priv->gphy_fw[i], 2047 gphy_fw_np, i); 2048 if (err) 2049 goto remove_gphy; 2050 i++; 2051 } 2052 2053 /* The standalone PHY11G requires 300ms to be fully 2054 * initialized and ready for any MDIO communication after being 2055 * taken out of reset. For the SoC-internal GPHY variant there 2056 * is no (known) documentation for the minimum time after a 2057 * reset. Use the same value as for the standalone variant as 2058 * some users have reported internal PHYs not being detected 2059 * without any delay. 2060 */ 2061 msleep(300); 2062 2063 return 0; 2064 2065 remove_gphy: 2066 for (i = 0; i < priv->num_gphy_fw; i++) 2067 gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]); 2068 return err; 2069 } 2070 2071 static int gswip_probe(struct platform_device *pdev) 2072 { 2073 struct gswip_priv *priv; 2074 struct device_node *np, *mdio_np, *gphy_fw_np; 2075 struct device *dev = &pdev->dev; 2076 int err; 2077 int i; 2078 u32 version; 2079 2080 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 2081 if (!priv) 2082 return -ENOMEM; 2083 2084 priv->gswip = devm_platform_ioremap_resource(pdev, 0); 2085 if (IS_ERR(priv->gswip)) 2086 return PTR_ERR(priv->gswip); 2087 2088 priv->mdio = devm_platform_ioremap_resource(pdev, 1); 2089 if (IS_ERR(priv->mdio)) 2090 return PTR_ERR(priv->mdio); 2091 2092 priv->mii = devm_platform_ioremap_resource(pdev, 2); 2093 if (IS_ERR(priv->mii)) 2094 return PTR_ERR(priv->mii); 2095 2096 priv->hw_info = of_device_get_match_data(dev); 2097 if (!priv->hw_info) 2098 return -EINVAL; 2099 2100 priv->ds = devm_kzalloc(dev, sizeof(*priv->ds), GFP_KERNEL); 2101 if (!priv->ds) 2102 return -ENOMEM; 2103 2104 priv->ds->dev = dev; 2105 priv->ds->num_ports = priv->hw_info->max_ports; 2106 priv->ds->priv = priv; 2107 priv->ds->ops = priv->hw_info->ops; 2108 priv->dev = dev; 2109 version = gswip_switch_r(priv, GSWIP_VERSION); 2110 2111 np = dev->of_node; 2112 switch (version) { 2113 case GSWIP_VERSION_2_0: 2114 case GSWIP_VERSION_2_1: 2115 if (!of_device_is_compatible(np, "lantiq,xrx200-gswip")) 2116 return -EINVAL; 2117 break; 2118 case GSWIP_VERSION_2_2: 2119 case GSWIP_VERSION_2_2_ETC: 2120 if (!of_device_is_compatible(np, "lantiq,xrx300-gswip") && 2121 !of_device_is_compatible(np, "lantiq,xrx330-gswip")) 2122 return -EINVAL; 2123 break; 2124 default: 2125 dev_err(dev, "unknown GSWIP version: 0x%x", version); 2126 return -ENOENT; 2127 } 2128 2129 /* bring up the mdio bus */ 2130 gphy_fw_np = of_get_compatible_child(dev->of_node, "lantiq,gphy-fw"); 2131 if (gphy_fw_np) { 2132 err = gswip_gphy_fw_list(priv, gphy_fw_np, version); 2133 of_node_put(gphy_fw_np); 2134 if (err) { 2135 dev_err(dev, "gphy fw probe failed\n"); 2136 return err; 2137 } 2138 } 2139 2140 /* bring up the mdio bus */ 2141 mdio_np = of_get_compatible_child(dev->of_node, "lantiq,xrx200-mdio"); 2142 if (mdio_np) { 2143 err = gswip_mdio(priv, mdio_np); 2144 if (err) { 2145 dev_err(dev, "mdio probe failed\n"); 2146 goto put_mdio_node; 2147 } 2148 } 2149 2150 err = dsa_register_switch(priv->ds); 2151 if (err) { 2152 dev_err(dev, "dsa switch register failed: %i\n", err); 2153 goto mdio_bus; 2154 } 2155 if (!dsa_is_cpu_port(priv->ds, priv->hw_info->cpu_port)) { 2156 dev_err(dev, "wrong CPU port defined, HW only supports port: %i", 2157 priv->hw_info->cpu_port); 2158 err = -EINVAL; 2159 goto disable_switch; 2160 } 2161 2162 platform_set_drvdata(pdev, priv); 2163 2164 dev_info(dev, "probed GSWIP version %lx mod %lx\n", 2165 (version & GSWIP_VERSION_REV_MASK) >> GSWIP_VERSION_REV_SHIFT, 2166 (version & GSWIP_VERSION_MOD_MASK) >> GSWIP_VERSION_MOD_SHIFT); 2167 return 0; 2168 2169 disable_switch: 2170 gswip_mdio_mask(priv, GSWIP_MDIO_GLOB_ENABLE, 0, GSWIP_MDIO_GLOB); 2171 dsa_unregister_switch(priv->ds); 2172 mdio_bus: 2173 if (mdio_np) 2174 mdiobus_unregister(priv->ds->slave_mii_bus); 2175 put_mdio_node: 2176 of_node_put(mdio_np); 2177 for (i = 0; i < priv->num_gphy_fw; i++) 2178 gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]); 2179 return err; 2180 } 2181 2182 static int gswip_remove(struct platform_device *pdev) 2183 { 2184 struct gswip_priv *priv = platform_get_drvdata(pdev); 2185 int i; 2186 2187 /* disable the switch */ 2188 gswip_mdio_mask(priv, GSWIP_MDIO_GLOB_ENABLE, 0, GSWIP_MDIO_GLOB); 2189 2190 dsa_unregister_switch(priv->ds); 2191 2192 if (priv->ds->slave_mii_bus) { 2193 mdiobus_unregister(priv->ds->slave_mii_bus); 2194 of_node_put(priv->ds->slave_mii_bus->dev.of_node); 2195 } 2196 2197 for (i = 0; i < priv->num_gphy_fw; i++) 2198 gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]); 2199 2200 return 0; 2201 } 2202 2203 static const struct gswip_hw_info gswip_xrx200 = { 2204 .max_ports = 7, 2205 .cpu_port = 6, 2206 .ops = &gswip_xrx200_switch_ops, 2207 }; 2208 2209 static const struct gswip_hw_info gswip_xrx300 = { 2210 .max_ports = 7, 2211 .cpu_port = 6, 2212 .ops = &gswip_xrx300_switch_ops, 2213 }; 2214 2215 static const struct of_device_id gswip_of_match[] = { 2216 { .compatible = "lantiq,xrx200-gswip", .data = &gswip_xrx200 }, 2217 { .compatible = "lantiq,xrx300-gswip", .data = &gswip_xrx300 }, 2218 { .compatible = "lantiq,xrx330-gswip", .data = &gswip_xrx300 }, 2219 {}, 2220 }; 2221 MODULE_DEVICE_TABLE(of, gswip_of_match); 2222 2223 static struct platform_driver gswip_driver = { 2224 .probe = gswip_probe, 2225 .remove = gswip_remove, 2226 .driver = { 2227 .name = "gswip", 2228 .of_match_table = gswip_of_match, 2229 }, 2230 }; 2231 2232 module_platform_driver(gswip_driver); 2233 2234 MODULE_FIRMWARE("lantiq/xrx300_phy11g_a21.bin"); 2235 MODULE_FIRMWARE("lantiq/xrx300_phy22f_a21.bin"); 2236 MODULE_FIRMWARE("lantiq/xrx200_phy11g_a14.bin"); 2237 MODULE_FIRMWARE("lantiq/xrx200_phy11g_a22.bin"); 2238 MODULE_FIRMWARE("lantiq/xrx200_phy22f_a14.bin"); 2239 MODULE_FIRMWARE("lantiq/xrx200_phy22f_a22.bin"); 2240 MODULE_AUTHOR("Hauke Mehrtens <hauke@hauke-m.de>"); 2241 MODULE_DESCRIPTION("Lantiq / Intel GSWIP driver"); 2242 MODULE_LICENSE("GPL v2"); 2243