1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Lantiq / Intel GSWIP switch driver for VRX200, xRX300 and xRX330 SoCs 4 * 5 * Copyright (C) 2010 Lantiq Deutschland 6 * Copyright (C) 2012 John Crispin <john@phrozen.org> 7 * Copyright (C) 2017 - 2019 Hauke Mehrtens <hauke@hauke-m.de> 8 * 9 * The VLAN and bridge model the GSWIP hardware uses does not directly 10 * matches the model DSA uses. 11 * 12 * The hardware has 64 possible table entries for bridges with one VLAN 13 * ID, one flow id and a list of ports for each bridge. All entries which 14 * match the same flow ID are combined in the mac learning table, they 15 * act as one global bridge. 16 * The hardware does not support VLAN filter on the port, but on the 17 * bridge, this driver converts the DSA model to the hardware. 18 * 19 * The CPU gets all the exception frames which do not match any forwarding 20 * rule and the CPU port is also added to all bridges. This makes it possible 21 * to handle all the special cases easily in software. 22 * At the initialization the driver allocates one bridge table entry for 23 * each switch port which is used when the port is used without an 24 * explicit bridge. This prevents the frames from being forwarded 25 * between all LAN ports by default. 26 */ 27 28 #include <linux/clk.h> 29 #include <linux/delay.h> 30 #include <linux/etherdevice.h> 31 #include <linux/firmware.h> 32 #include <linux/if_bridge.h> 33 #include <linux/if_vlan.h> 34 #include <linux/iopoll.h> 35 #include <linux/mfd/syscon.h> 36 #include <linux/module.h> 37 #include <linux/of_mdio.h> 38 #include <linux/of_net.h> 39 #include <linux/of_platform.h> 40 #include <linux/phy.h> 41 #include <linux/phylink.h> 42 #include <linux/platform_device.h> 43 #include <linux/regmap.h> 44 #include <linux/reset.h> 45 #include <net/dsa.h> 46 #include <dt-bindings/mips/lantiq_rcu_gphy.h> 47 48 #include "lantiq_pce.h" 49 50 /* GSWIP MDIO Registers */ 51 #define GSWIP_MDIO_GLOB 0x00 52 #define GSWIP_MDIO_GLOB_ENABLE BIT(15) 53 #define GSWIP_MDIO_CTRL 0x08 54 #define GSWIP_MDIO_CTRL_BUSY BIT(12) 55 #define GSWIP_MDIO_CTRL_RD BIT(11) 56 #define GSWIP_MDIO_CTRL_WR BIT(10) 57 #define GSWIP_MDIO_CTRL_PHYAD_MASK 0x1f 58 #define GSWIP_MDIO_CTRL_PHYAD_SHIFT 5 59 #define GSWIP_MDIO_CTRL_REGAD_MASK 0x1f 60 #define GSWIP_MDIO_READ 0x09 61 #define GSWIP_MDIO_WRITE 0x0A 62 #define GSWIP_MDIO_MDC_CFG0 0x0B 63 #define GSWIP_MDIO_MDC_CFG1 0x0C 64 #define GSWIP_MDIO_PHYp(p) (0x15 - (p)) 65 #define GSWIP_MDIO_PHY_LINK_MASK 0x6000 66 #define GSWIP_MDIO_PHY_LINK_AUTO 0x0000 67 #define GSWIP_MDIO_PHY_LINK_DOWN 0x4000 68 #define GSWIP_MDIO_PHY_LINK_UP 0x2000 69 #define GSWIP_MDIO_PHY_SPEED_MASK 0x1800 70 #define GSWIP_MDIO_PHY_SPEED_AUTO 0x1800 71 #define GSWIP_MDIO_PHY_SPEED_M10 0x0000 72 #define GSWIP_MDIO_PHY_SPEED_M100 0x0800 73 #define GSWIP_MDIO_PHY_SPEED_G1 0x1000 74 #define GSWIP_MDIO_PHY_FDUP_MASK 0x0600 75 #define GSWIP_MDIO_PHY_FDUP_AUTO 0x0000 76 #define GSWIP_MDIO_PHY_FDUP_EN 0x0200 77 #define GSWIP_MDIO_PHY_FDUP_DIS 0x0600 78 #define GSWIP_MDIO_PHY_FCONTX_MASK 0x0180 79 #define GSWIP_MDIO_PHY_FCONTX_AUTO 0x0000 80 #define GSWIP_MDIO_PHY_FCONTX_EN 0x0100 81 #define GSWIP_MDIO_PHY_FCONTX_DIS 0x0180 82 #define GSWIP_MDIO_PHY_FCONRX_MASK 0x0060 83 #define GSWIP_MDIO_PHY_FCONRX_AUTO 0x0000 84 #define GSWIP_MDIO_PHY_FCONRX_EN 0x0020 85 #define GSWIP_MDIO_PHY_FCONRX_DIS 0x0060 86 #define GSWIP_MDIO_PHY_ADDR_MASK 0x001f 87 #define GSWIP_MDIO_PHY_MASK (GSWIP_MDIO_PHY_ADDR_MASK | \ 88 GSWIP_MDIO_PHY_FCONRX_MASK | \ 89 GSWIP_MDIO_PHY_FCONTX_MASK | \ 90 GSWIP_MDIO_PHY_LINK_MASK | \ 91 GSWIP_MDIO_PHY_SPEED_MASK | \ 92 GSWIP_MDIO_PHY_FDUP_MASK) 93 94 /* GSWIP MII Registers */ 95 #define GSWIP_MII_CFGp(p) (0x2 * (p)) 96 #define GSWIP_MII_CFG_RESET BIT(15) 97 #define GSWIP_MII_CFG_EN BIT(14) 98 #define GSWIP_MII_CFG_ISOLATE BIT(13) 99 #define GSWIP_MII_CFG_LDCLKDIS BIT(12) 100 #define GSWIP_MII_CFG_RGMII_IBS BIT(8) 101 #define GSWIP_MII_CFG_RMII_CLK BIT(7) 102 #define GSWIP_MII_CFG_MODE_MIIP 0x0 103 #define GSWIP_MII_CFG_MODE_MIIM 0x1 104 #define GSWIP_MII_CFG_MODE_RMIIP 0x2 105 #define GSWIP_MII_CFG_MODE_RMIIM 0x3 106 #define GSWIP_MII_CFG_MODE_RGMII 0x4 107 #define GSWIP_MII_CFG_MODE_GMII 0x9 108 #define GSWIP_MII_CFG_MODE_MASK 0xf 109 #define GSWIP_MII_CFG_RATE_M2P5 0x00 110 #define GSWIP_MII_CFG_RATE_M25 0x10 111 #define GSWIP_MII_CFG_RATE_M125 0x20 112 #define GSWIP_MII_CFG_RATE_M50 0x30 113 #define GSWIP_MII_CFG_RATE_AUTO 0x40 114 #define GSWIP_MII_CFG_RATE_MASK 0x70 115 #define GSWIP_MII_PCDU0 0x01 116 #define GSWIP_MII_PCDU1 0x03 117 #define GSWIP_MII_PCDU5 0x05 118 #define GSWIP_MII_PCDU_TXDLY_MASK GENMASK(2, 0) 119 #define GSWIP_MII_PCDU_RXDLY_MASK GENMASK(9, 7) 120 121 /* GSWIP Core Registers */ 122 #define GSWIP_SWRES 0x000 123 #define GSWIP_SWRES_R1 BIT(1) /* GSWIP Software reset */ 124 #define GSWIP_SWRES_R0 BIT(0) /* GSWIP Hardware reset */ 125 #define GSWIP_VERSION 0x013 126 #define GSWIP_VERSION_REV_SHIFT 0 127 #define GSWIP_VERSION_REV_MASK GENMASK(7, 0) 128 #define GSWIP_VERSION_MOD_SHIFT 8 129 #define GSWIP_VERSION_MOD_MASK GENMASK(15, 8) 130 #define GSWIP_VERSION_2_0 0x100 131 #define GSWIP_VERSION_2_1 0x021 132 #define GSWIP_VERSION_2_2 0x122 133 #define GSWIP_VERSION_2_2_ETC 0x022 134 135 #define GSWIP_BM_RAM_VAL(x) (0x043 - (x)) 136 #define GSWIP_BM_RAM_ADDR 0x044 137 #define GSWIP_BM_RAM_CTRL 0x045 138 #define GSWIP_BM_RAM_CTRL_BAS BIT(15) 139 #define GSWIP_BM_RAM_CTRL_OPMOD BIT(5) 140 #define GSWIP_BM_RAM_CTRL_ADDR_MASK GENMASK(4, 0) 141 #define GSWIP_BM_QUEUE_GCTRL 0x04A 142 #define GSWIP_BM_QUEUE_GCTRL_GL_MOD BIT(10) 143 /* buffer management Port Configuration Register */ 144 #define GSWIP_BM_PCFGp(p) (0x080 + ((p) * 2)) 145 #define GSWIP_BM_PCFG_CNTEN BIT(0) /* RMON Counter Enable */ 146 #define GSWIP_BM_PCFG_IGCNT BIT(1) /* Ingres Special Tag RMON count */ 147 /* buffer management Port Control Register */ 148 #define GSWIP_BM_RMON_CTRLp(p) (0x81 + ((p) * 2)) 149 #define GSWIP_BM_CTRL_RMON_RAM1_RES BIT(0) /* Software Reset for RMON RAM 1 */ 150 #define GSWIP_BM_CTRL_RMON_RAM2_RES BIT(1) /* Software Reset for RMON RAM 2 */ 151 152 /* PCE */ 153 #define GSWIP_PCE_TBL_KEY(x) (0x447 - (x)) 154 #define GSWIP_PCE_TBL_MASK 0x448 155 #define GSWIP_PCE_TBL_VAL(x) (0x44D - (x)) 156 #define GSWIP_PCE_TBL_ADDR 0x44E 157 #define GSWIP_PCE_TBL_CTRL 0x44F 158 #define GSWIP_PCE_TBL_CTRL_BAS BIT(15) 159 #define GSWIP_PCE_TBL_CTRL_TYPE BIT(13) 160 #define GSWIP_PCE_TBL_CTRL_VLD BIT(12) 161 #define GSWIP_PCE_TBL_CTRL_KEYFORM BIT(11) 162 #define GSWIP_PCE_TBL_CTRL_GMAP_MASK GENMASK(10, 7) 163 #define GSWIP_PCE_TBL_CTRL_OPMOD_MASK GENMASK(6, 5) 164 #define GSWIP_PCE_TBL_CTRL_OPMOD_ADRD 0x00 165 #define GSWIP_PCE_TBL_CTRL_OPMOD_ADWR 0x20 166 #define GSWIP_PCE_TBL_CTRL_OPMOD_KSRD 0x40 167 #define GSWIP_PCE_TBL_CTRL_OPMOD_KSWR 0x60 168 #define GSWIP_PCE_TBL_CTRL_ADDR_MASK GENMASK(4, 0) 169 #define GSWIP_PCE_PMAP1 0x453 /* Monitoring port map */ 170 #define GSWIP_PCE_PMAP2 0x454 /* Default Multicast port map */ 171 #define GSWIP_PCE_PMAP3 0x455 /* Default Unknown Unicast port map */ 172 #define GSWIP_PCE_GCTRL_0 0x456 173 #define GSWIP_PCE_GCTRL_0_MTFL BIT(0) /* MAC Table Flushing */ 174 #define GSWIP_PCE_GCTRL_0_MC_VALID BIT(3) 175 #define GSWIP_PCE_GCTRL_0_VLAN BIT(14) /* VLAN aware Switching */ 176 #define GSWIP_PCE_GCTRL_1 0x457 177 #define GSWIP_PCE_GCTRL_1_MAC_GLOCK BIT(2) /* MAC Address table lock */ 178 #define GSWIP_PCE_GCTRL_1_MAC_GLOCK_MOD BIT(3) /* Mac address table lock forwarding mode */ 179 #define GSWIP_PCE_PCTRL_0p(p) (0x480 + ((p) * 0xA)) 180 #define GSWIP_PCE_PCTRL_0_TVM BIT(5) /* Transparent VLAN mode */ 181 #define GSWIP_PCE_PCTRL_0_VREP BIT(6) /* VLAN Replace Mode */ 182 #define GSWIP_PCE_PCTRL_0_INGRESS BIT(11) /* Accept special tag in ingress */ 183 #define GSWIP_PCE_PCTRL_0_PSTATE_LISTEN 0x0 184 #define GSWIP_PCE_PCTRL_0_PSTATE_RX 0x1 185 #define GSWIP_PCE_PCTRL_0_PSTATE_TX 0x2 186 #define GSWIP_PCE_PCTRL_0_PSTATE_LEARNING 0x3 187 #define GSWIP_PCE_PCTRL_0_PSTATE_FORWARDING 0x7 188 #define GSWIP_PCE_PCTRL_0_PSTATE_MASK GENMASK(2, 0) 189 #define GSWIP_PCE_VCTRL(p) (0x485 + ((p) * 0xA)) 190 #define GSWIP_PCE_VCTRL_UVR BIT(0) /* Unknown VLAN Rule */ 191 #define GSWIP_PCE_VCTRL_VIMR BIT(3) /* VLAN Ingress Member violation rule */ 192 #define GSWIP_PCE_VCTRL_VEMR BIT(4) /* VLAN Egress Member violation rule */ 193 #define GSWIP_PCE_VCTRL_VSR BIT(5) /* VLAN Security */ 194 #define GSWIP_PCE_VCTRL_VID0 BIT(6) /* Priority Tagged Rule */ 195 #define GSWIP_PCE_DEFPVID(p) (0x486 + ((p) * 0xA)) 196 197 #define GSWIP_MAC_FLEN 0x8C5 198 #define GSWIP_MAC_CTRL_0p(p) (0x903 + ((p) * 0xC)) 199 #define GSWIP_MAC_CTRL_0_PADEN BIT(8) 200 #define GSWIP_MAC_CTRL_0_FCS_EN BIT(7) 201 #define GSWIP_MAC_CTRL_0_FCON_MASK 0x0070 202 #define GSWIP_MAC_CTRL_0_FCON_AUTO 0x0000 203 #define GSWIP_MAC_CTRL_0_FCON_RX 0x0010 204 #define GSWIP_MAC_CTRL_0_FCON_TX 0x0020 205 #define GSWIP_MAC_CTRL_0_FCON_RXTX 0x0030 206 #define GSWIP_MAC_CTRL_0_FCON_NONE 0x0040 207 #define GSWIP_MAC_CTRL_0_FDUP_MASK 0x000C 208 #define GSWIP_MAC_CTRL_0_FDUP_AUTO 0x0000 209 #define GSWIP_MAC_CTRL_0_FDUP_EN 0x0004 210 #define GSWIP_MAC_CTRL_0_FDUP_DIS 0x000C 211 #define GSWIP_MAC_CTRL_0_GMII_MASK 0x0003 212 #define GSWIP_MAC_CTRL_0_GMII_AUTO 0x0000 213 #define GSWIP_MAC_CTRL_0_GMII_MII 0x0001 214 #define GSWIP_MAC_CTRL_0_GMII_RGMII 0x0002 215 #define GSWIP_MAC_CTRL_2p(p) (0x905 + ((p) * 0xC)) 216 #define GSWIP_MAC_CTRL_2_LCHKL BIT(2) /* Frame Length Check Long Enable */ 217 #define GSWIP_MAC_CTRL_2_MLEN BIT(3) /* Maximum Untagged Frame Lnegth */ 218 219 /* Ethernet Switch Fetch DMA Port Control Register */ 220 #define GSWIP_FDMA_PCTRLp(p) (0xA80 + ((p) * 0x6)) 221 #define GSWIP_FDMA_PCTRL_EN BIT(0) /* FDMA Port Enable */ 222 #define GSWIP_FDMA_PCTRL_STEN BIT(1) /* Special Tag Insertion Enable */ 223 #define GSWIP_FDMA_PCTRL_VLANMOD_MASK GENMASK(4, 3) /* VLAN Modification Control */ 224 #define GSWIP_FDMA_PCTRL_VLANMOD_SHIFT 3 /* VLAN Modification Control */ 225 #define GSWIP_FDMA_PCTRL_VLANMOD_DIS (0x0 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT) 226 #define GSWIP_FDMA_PCTRL_VLANMOD_PRIO (0x1 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT) 227 #define GSWIP_FDMA_PCTRL_VLANMOD_ID (0x2 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT) 228 #define GSWIP_FDMA_PCTRL_VLANMOD_BOTH (0x3 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT) 229 230 /* Ethernet Switch Store DMA Port Control Register */ 231 #define GSWIP_SDMA_PCTRLp(p) (0xBC0 + ((p) * 0x6)) 232 #define GSWIP_SDMA_PCTRL_EN BIT(0) /* SDMA Port Enable */ 233 #define GSWIP_SDMA_PCTRL_FCEN BIT(1) /* Flow Control Enable */ 234 #define GSWIP_SDMA_PCTRL_PAUFWD BIT(3) /* Pause Frame Forwarding */ 235 236 #define GSWIP_TABLE_ACTIVE_VLAN 0x01 237 #define GSWIP_TABLE_VLAN_MAPPING 0x02 238 #define GSWIP_TABLE_MAC_BRIDGE 0x0b 239 #define GSWIP_TABLE_MAC_BRIDGE_STATIC 0x01 /* Static not, aging entry */ 240 241 #define XRX200_GPHY_FW_ALIGN (16 * 1024) 242 243 /* Maximum packet size supported by the switch. In theory this should be 10240, 244 * but long packets currently cause lock-ups with an MTU of over 2526. Medium 245 * packets are sometimes dropped (e.g. TCP over 2477, UDP over 2516-2519, ICMP 246 * over 2526), hence an MTU value of 2400 seems safe. This issue only affects 247 * packet reception. This is probably caused by the PPA engine, which is on the 248 * RX part of the device. Packet transmission works properly up to 10240. 249 */ 250 #define GSWIP_MAX_PACKET_LENGTH 2400 251 252 struct gswip_hw_info { 253 int max_ports; 254 int cpu_port; 255 const struct dsa_switch_ops *ops; 256 }; 257 258 struct xway_gphy_match_data { 259 char *fe_firmware_name; 260 char *ge_firmware_name; 261 }; 262 263 struct gswip_gphy_fw { 264 struct clk *clk_gate; 265 struct reset_control *reset; 266 u32 fw_addr_offset; 267 char *fw_name; 268 }; 269 270 struct gswip_vlan { 271 struct net_device *bridge; 272 u16 vid; 273 u8 fid; 274 }; 275 276 struct gswip_priv { 277 __iomem void *gswip; 278 __iomem void *mdio; 279 __iomem void *mii; 280 const struct gswip_hw_info *hw_info; 281 const struct xway_gphy_match_data *gphy_fw_name_cfg; 282 struct dsa_switch *ds; 283 struct device *dev; 284 struct regmap *rcu_regmap; 285 struct gswip_vlan vlans[64]; 286 int num_gphy_fw; 287 struct gswip_gphy_fw *gphy_fw; 288 u32 port_vlan_filter; 289 struct mutex pce_table_lock; 290 }; 291 292 struct gswip_pce_table_entry { 293 u16 index; // PCE_TBL_ADDR.ADDR = pData->table_index 294 u16 table; // PCE_TBL_CTRL.ADDR = pData->table 295 u16 key[8]; 296 u16 val[5]; 297 u16 mask; 298 u8 gmap; 299 bool type; 300 bool valid; 301 bool key_mode; 302 }; 303 304 struct gswip_rmon_cnt_desc { 305 unsigned int size; 306 unsigned int offset; 307 const char *name; 308 }; 309 310 #define MIB_DESC(_size, _offset, _name) {.size = _size, .offset = _offset, .name = _name} 311 312 static const struct gswip_rmon_cnt_desc gswip_rmon_cnt[] = { 313 /** Receive Packet Count (only packets that are accepted and not discarded). */ 314 MIB_DESC(1, 0x1F, "RxGoodPkts"), 315 MIB_DESC(1, 0x23, "RxUnicastPkts"), 316 MIB_DESC(1, 0x22, "RxMulticastPkts"), 317 MIB_DESC(1, 0x21, "RxFCSErrorPkts"), 318 MIB_DESC(1, 0x1D, "RxUnderSizeGoodPkts"), 319 MIB_DESC(1, 0x1E, "RxUnderSizeErrorPkts"), 320 MIB_DESC(1, 0x1B, "RxOversizeGoodPkts"), 321 MIB_DESC(1, 0x1C, "RxOversizeErrorPkts"), 322 MIB_DESC(1, 0x20, "RxGoodPausePkts"), 323 MIB_DESC(1, 0x1A, "RxAlignErrorPkts"), 324 MIB_DESC(1, 0x12, "Rx64BytePkts"), 325 MIB_DESC(1, 0x13, "Rx127BytePkts"), 326 MIB_DESC(1, 0x14, "Rx255BytePkts"), 327 MIB_DESC(1, 0x15, "Rx511BytePkts"), 328 MIB_DESC(1, 0x16, "Rx1023BytePkts"), 329 /** Receive Size 1024-1522 (or more, if configured) Packet Count. */ 330 MIB_DESC(1, 0x17, "RxMaxBytePkts"), 331 MIB_DESC(1, 0x18, "RxDroppedPkts"), 332 MIB_DESC(1, 0x19, "RxFilteredPkts"), 333 MIB_DESC(2, 0x24, "RxGoodBytes"), 334 MIB_DESC(2, 0x26, "RxBadBytes"), 335 MIB_DESC(1, 0x11, "TxAcmDroppedPkts"), 336 MIB_DESC(1, 0x0C, "TxGoodPkts"), 337 MIB_DESC(1, 0x06, "TxUnicastPkts"), 338 MIB_DESC(1, 0x07, "TxMulticastPkts"), 339 MIB_DESC(1, 0x00, "Tx64BytePkts"), 340 MIB_DESC(1, 0x01, "Tx127BytePkts"), 341 MIB_DESC(1, 0x02, "Tx255BytePkts"), 342 MIB_DESC(1, 0x03, "Tx511BytePkts"), 343 MIB_DESC(1, 0x04, "Tx1023BytePkts"), 344 /** Transmit Size 1024-1522 (or more, if configured) Packet Count. */ 345 MIB_DESC(1, 0x05, "TxMaxBytePkts"), 346 MIB_DESC(1, 0x08, "TxSingleCollCount"), 347 MIB_DESC(1, 0x09, "TxMultCollCount"), 348 MIB_DESC(1, 0x0A, "TxLateCollCount"), 349 MIB_DESC(1, 0x0B, "TxExcessCollCount"), 350 MIB_DESC(1, 0x0D, "TxPauseCount"), 351 MIB_DESC(1, 0x10, "TxDroppedPkts"), 352 MIB_DESC(2, 0x0E, "TxGoodBytes"), 353 }; 354 355 static u32 gswip_switch_r(struct gswip_priv *priv, u32 offset) 356 { 357 return __raw_readl(priv->gswip + (offset * 4)); 358 } 359 360 static void gswip_switch_w(struct gswip_priv *priv, u32 val, u32 offset) 361 { 362 __raw_writel(val, priv->gswip + (offset * 4)); 363 } 364 365 static void gswip_switch_mask(struct gswip_priv *priv, u32 clear, u32 set, 366 u32 offset) 367 { 368 u32 val = gswip_switch_r(priv, offset); 369 370 val &= ~(clear); 371 val |= set; 372 gswip_switch_w(priv, val, offset); 373 } 374 375 static u32 gswip_switch_r_timeout(struct gswip_priv *priv, u32 offset, 376 u32 cleared) 377 { 378 u32 val; 379 380 return readx_poll_timeout(__raw_readl, priv->gswip + (offset * 4), val, 381 (val & cleared) == 0, 20, 50000); 382 } 383 384 static u32 gswip_mdio_r(struct gswip_priv *priv, u32 offset) 385 { 386 return __raw_readl(priv->mdio + (offset * 4)); 387 } 388 389 static void gswip_mdio_w(struct gswip_priv *priv, u32 val, u32 offset) 390 { 391 __raw_writel(val, priv->mdio + (offset * 4)); 392 } 393 394 static void gswip_mdio_mask(struct gswip_priv *priv, u32 clear, u32 set, 395 u32 offset) 396 { 397 u32 val = gswip_mdio_r(priv, offset); 398 399 val &= ~(clear); 400 val |= set; 401 gswip_mdio_w(priv, val, offset); 402 } 403 404 static u32 gswip_mii_r(struct gswip_priv *priv, u32 offset) 405 { 406 return __raw_readl(priv->mii + (offset * 4)); 407 } 408 409 static void gswip_mii_w(struct gswip_priv *priv, u32 val, u32 offset) 410 { 411 __raw_writel(val, priv->mii + (offset * 4)); 412 } 413 414 static void gswip_mii_mask(struct gswip_priv *priv, u32 clear, u32 set, 415 u32 offset) 416 { 417 u32 val = gswip_mii_r(priv, offset); 418 419 val &= ~(clear); 420 val |= set; 421 gswip_mii_w(priv, val, offset); 422 } 423 424 static void gswip_mii_mask_cfg(struct gswip_priv *priv, u32 clear, u32 set, 425 int port) 426 { 427 /* There's no MII_CFG register for the CPU port */ 428 if (!dsa_is_cpu_port(priv->ds, port)) 429 gswip_mii_mask(priv, clear, set, GSWIP_MII_CFGp(port)); 430 } 431 432 static void gswip_mii_mask_pcdu(struct gswip_priv *priv, u32 clear, u32 set, 433 int port) 434 { 435 switch (port) { 436 case 0: 437 gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU0); 438 break; 439 case 1: 440 gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU1); 441 break; 442 case 5: 443 gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU5); 444 break; 445 } 446 } 447 448 static int gswip_mdio_poll(struct gswip_priv *priv) 449 { 450 int cnt = 100; 451 452 while (likely(cnt--)) { 453 u32 ctrl = gswip_mdio_r(priv, GSWIP_MDIO_CTRL); 454 455 if ((ctrl & GSWIP_MDIO_CTRL_BUSY) == 0) 456 return 0; 457 usleep_range(20, 40); 458 } 459 460 return -ETIMEDOUT; 461 } 462 463 static int gswip_mdio_wr(struct mii_bus *bus, int addr, int reg, u16 val) 464 { 465 struct gswip_priv *priv = bus->priv; 466 int err; 467 468 err = gswip_mdio_poll(priv); 469 if (err) { 470 dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n"); 471 return err; 472 } 473 474 gswip_mdio_w(priv, val, GSWIP_MDIO_WRITE); 475 gswip_mdio_w(priv, GSWIP_MDIO_CTRL_BUSY | GSWIP_MDIO_CTRL_WR | 476 ((addr & GSWIP_MDIO_CTRL_PHYAD_MASK) << GSWIP_MDIO_CTRL_PHYAD_SHIFT) | 477 (reg & GSWIP_MDIO_CTRL_REGAD_MASK), 478 GSWIP_MDIO_CTRL); 479 480 return 0; 481 } 482 483 static int gswip_mdio_rd(struct mii_bus *bus, int addr, int reg) 484 { 485 struct gswip_priv *priv = bus->priv; 486 int err; 487 488 err = gswip_mdio_poll(priv); 489 if (err) { 490 dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n"); 491 return err; 492 } 493 494 gswip_mdio_w(priv, GSWIP_MDIO_CTRL_BUSY | GSWIP_MDIO_CTRL_RD | 495 ((addr & GSWIP_MDIO_CTRL_PHYAD_MASK) << GSWIP_MDIO_CTRL_PHYAD_SHIFT) | 496 (reg & GSWIP_MDIO_CTRL_REGAD_MASK), 497 GSWIP_MDIO_CTRL); 498 499 err = gswip_mdio_poll(priv); 500 if (err) { 501 dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n"); 502 return err; 503 } 504 505 return gswip_mdio_r(priv, GSWIP_MDIO_READ); 506 } 507 508 static int gswip_mdio(struct gswip_priv *priv, struct device_node *mdio_np) 509 { 510 struct dsa_switch *ds = priv->ds; 511 int err; 512 513 ds->slave_mii_bus = mdiobus_alloc(); 514 if (!ds->slave_mii_bus) 515 return -ENOMEM; 516 517 ds->slave_mii_bus->priv = priv; 518 ds->slave_mii_bus->read = gswip_mdio_rd; 519 ds->slave_mii_bus->write = gswip_mdio_wr; 520 ds->slave_mii_bus->name = "lantiq,xrx200-mdio"; 521 snprintf(ds->slave_mii_bus->id, MII_BUS_ID_SIZE, "%s-mii", 522 dev_name(priv->dev)); 523 ds->slave_mii_bus->parent = priv->dev; 524 ds->slave_mii_bus->phy_mask = ~ds->phys_mii_mask; 525 526 err = of_mdiobus_register(ds->slave_mii_bus, mdio_np); 527 if (err) 528 mdiobus_free(ds->slave_mii_bus); 529 530 return err; 531 } 532 533 static int gswip_pce_table_entry_read(struct gswip_priv *priv, 534 struct gswip_pce_table_entry *tbl) 535 { 536 int i; 537 int err; 538 u16 crtl; 539 u16 addr_mode = tbl->key_mode ? GSWIP_PCE_TBL_CTRL_OPMOD_KSRD : 540 GSWIP_PCE_TBL_CTRL_OPMOD_ADRD; 541 542 mutex_lock(&priv->pce_table_lock); 543 544 err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, 545 GSWIP_PCE_TBL_CTRL_BAS); 546 if (err) { 547 mutex_unlock(&priv->pce_table_lock); 548 return err; 549 } 550 551 gswip_switch_w(priv, tbl->index, GSWIP_PCE_TBL_ADDR); 552 gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK | 553 GSWIP_PCE_TBL_CTRL_OPMOD_MASK, 554 tbl->table | addr_mode | GSWIP_PCE_TBL_CTRL_BAS, 555 GSWIP_PCE_TBL_CTRL); 556 557 err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, 558 GSWIP_PCE_TBL_CTRL_BAS); 559 if (err) { 560 mutex_unlock(&priv->pce_table_lock); 561 return err; 562 } 563 564 for (i = 0; i < ARRAY_SIZE(tbl->key); i++) 565 tbl->key[i] = gswip_switch_r(priv, GSWIP_PCE_TBL_KEY(i)); 566 567 for (i = 0; i < ARRAY_SIZE(tbl->val); i++) 568 tbl->val[i] = gswip_switch_r(priv, GSWIP_PCE_TBL_VAL(i)); 569 570 tbl->mask = gswip_switch_r(priv, GSWIP_PCE_TBL_MASK); 571 572 crtl = gswip_switch_r(priv, GSWIP_PCE_TBL_CTRL); 573 574 tbl->type = !!(crtl & GSWIP_PCE_TBL_CTRL_TYPE); 575 tbl->valid = !!(crtl & GSWIP_PCE_TBL_CTRL_VLD); 576 tbl->gmap = (crtl & GSWIP_PCE_TBL_CTRL_GMAP_MASK) >> 7; 577 578 mutex_unlock(&priv->pce_table_lock); 579 580 return 0; 581 } 582 583 static int gswip_pce_table_entry_write(struct gswip_priv *priv, 584 struct gswip_pce_table_entry *tbl) 585 { 586 int i; 587 int err; 588 u16 crtl; 589 u16 addr_mode = tbl->key_mode ? GSWIP_PCE_TBL_CTRL_OPMOD_KSWR : 590 GSWIP_PCE_TBL_CTRL_OPMOD_ADWR; 591 592 mutex_lock(&priv->pce_table_lock); 593 594 err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, 595 GSWIP_PCE_TBL_CTRL_BAS); 596 if (err) { 597 mutex_unlock(&priv->pce_table_lock); 598 return err; 599 } 600 601 gswip_switch_w(priv, tbl->index, GSWIP_PCE_TBL_ADDR); 602 gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK | 603 GSWIP_PCE_TBL_CTRL_OPMOD_MASK, 604 tbl->table | addr_mode, 605 GSWIP_PCE_TBL_CTRL); 606 607 for (i = 0; i < ARRAY_SIZE(tbl->key); i++) 608 gswip_switch_w(priv, tbl->key[i], GSWIP_PCE_TBL_KEY(i)); 609 610 for (i = 0; i < ARRAY_SIZE(tbl->val); i++) 611 gswip_switch_w(priv, tbl->val[i], GSWIP_PCE_TBL_VAL(i)); 612 613 gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK | 614 GSWIP_PCE_TBL_CTRL_OPMOD_MASK, 615 tbl->table | addr_mode, 616 GSWIP_PCE_TBL_CTRL); 617 618 gswip_switch_w(priv, tbl->mask, GSWIP_PCE_TBL_MASK); 619 620 crtl = gswip_switch_r(priv, GSWIP_PCE_TBL_CTRL); 621 crtl &= ~(GSWIP_PCE_TBL_CTRL_TYPE | GSWIP_PCE_TBL_CTRL_VLD | 622 GSWIP_PCE_TBL_CTRL_GMAP_MASK); 623 if (tbl->type) 624 crtl |= GSWIP_PCE_TBL_CTRL_TYPE; 625 if (tbl->valid) 626 crtl |= GSWIP_PCE_TBL_CTRL_VLD; 627 crtl |= (tbl->gmap << 7) & GSWIP_PCE_TBL_CTRL_GMAP_MASK; 628 crtl |= GSWIP_PCE_TBL_CTRL_BAS; 629 gswip_switch_w(priv, crtl, GSWIP_PCE_TBL_CTRL); 630 631 err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, 632 GSWIP_PCE_TBL_CTRL_BAS); 633 634 mutex_unlock(&priv->pce_table_lock); 635 636 return err; 637 } 638 639 /* Add the LAN port into a bridge with the CPU port by 640 * default. This prevents automatic forwarding of 641 * packages between the LAN ports when no explicit 642 * bridge is configured. 643 */ 644 static int gswip_add_single_port_br(struct gswip_priv *priv, int port, bool add) 645 { 646 struct gswip_pce_table_entry vlan_active = {0,}; 647 struct gswip_pce_table_entry vlan_mapping = {0,}; 648 unsigned int cpu_port = priv->hw_info->cpu_port; 649 unsigned int max_ports = priv->hw_info->max_ports; 650 int err; 651 652 if (port >= max_ports) { 653 dev_err(priv->dev, "single port for %i supported\n", port); 654 return -EIO; 655 } 656 657 vlan_active.index = port + 1; 658 vlan_active.table = GSWIP_TABLE_ACTIVE_VLAN; 659 vlan_active.key[0] = 0; /* vid */ 660 vlan_active.val[0] = port + 1 /* fid */; 661 vlan_active.valid = add; 662 err = gswip_pce_table_entry_write(priv, &vlan_active); 663 if (err) { 664 dev_err(priv->dev, "failed to write active VLAN: %d\n", err); 665 return err; 666 } 667 668 if (!add) 669 return 0; 670 671 vlan_mapping.index = port + 1; 672 vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; 673 vlan_mapping.val[0] = 0 /* vid */; 674 vlan_mapping.val[1] = BIT(port) | BIT(cpu_port); 675 vlan_mapping.val[2] = 0; 676 err = gswip_pce_table_entry_write(priv, &vlan_mapping); 677 if (err) { 678 dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err); 679 return err; 680 } 681 682 return 0; 683 } 684 685 static int gswip_port_enable(struct dsa_switch *ds, int port, 686 struct phy_device *phydev) 687 { 688 struct gswip_priv *priv = ds->priv; 689 int err; 690 691 if (!dsa_is_user_port(ds, port)) 692 return 0; 693 694 if (!dsa_is_cpu_port(ds, port)) { 695 err = gswip_add_single_port_br(priv, port, true); 696 if (err) 697 return err; 698 } 699 700 /* RMON Counter Enable for port */ 701 gswip_switch_w(priv, GSWIP_BM_PCFG_CNTEN, GSWIP_BM_PCFGp(port)); 702 703 /* enable port fetch/store dma & VLAN Modification */ 704 gswip_switch_mask(priv, 0, GSWIP_FDMA_PCTRL_EN | 705 GSWIP_FDMA_PCTRL_VLANMOD_BOTH, 706 GSWIP_FDMA_PCTRLp(port)); 707 gswip_switch_mask(priv, 0, GSWIP_SDMA_PCTRL_EN, 708 GSWIP_SDMA_PCTRLp(port)); 709 710 if (!dsa_is_cpu_port(ds, port)) { 711 u32 mdio_phy = 0; 712 713 if (phydev) 714 mdio_phy = phydev->mdio.addr & GSWIP_MDIO_PHY_ADDR_MASK; 715 716 gswip_mdio_mask(priv, GSWIP_MDIO_PHY_ADDR_MASK, mdio_phy, 717 GSWIP_MDIO_PHYp(port)); 718 } 719 720 return 0; 721 } 722 723 static void gswip_port_disable(struct dsa_switch *ds, int port) 724 { 725 struct gswip_priv *priv = ds->priv; 726 727 if (!dsa_is_user_port(ds, port)) 728 return; 729 730 gswip_switch_mask(priv, GSWIP_FDMA_PCTRL_EN, 0, 731 GSWIP_FDMA_PCTRLp(port)); 732 gswip_switch_mask(priv, GSWIP_SDMA_PCTRL_EN, 0, 733 GSWIP_SDMA_PCTRLp(port)); 734 } 735 736 static int gswip_pce_load_microcode(struct gswip_priv *priv) 737 { 738 int i; 739 int err; 740 741 gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK | 742 GSWIP_PCE_TBL_CTRL_OPMOD_MASK, 743 GSWIP_PCE_TBL_CTRL_OPMOD_ADWR, GSWIP_PCE_TBL_CTRL); 744 gswip_switch_w(priv, 0, GSWIP_PCE_TBL_MASK); 745 746 for (i = 0; i < ARRAY_SIZE(gswip_pce_microcode); i++) { 747 gswip_switch_w(priv, i, GSWIP_PCE_TBL_ADDR); 748 gswip_switch_w(priv, gswip_pce_microcode[i].val_0, 749 GSWIP_PCE_TBL_VAL(0)); 750 gswip_switch_w(priv, gswip_pce_microcode[i].val_1, 751 GSWIP_PCE_TBL_VAL(1)); 752 gswip_switch_w(priv, gswip_pce_microcode[i].val_2, 753 GSWIP_PCE_TBL_VAL(2)); 754 gswip_switch_w(priv, gswip_pce_microcode[i].val_3, 755 GSWIP_PCE_TBL_VAL(3)); 756 757 /* start the table access: */ 758 gswip_switch_mask(priv, 0, GSWIP_PCE_TBL_CTRL_BAS, 759 GSWIP_PCE_TBL_CTRL); 760 err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL, 761 GSWIP_PCE_TBL_CTRL_BAS); 762 if (err) 763 return err; 764 } 765 766 /* tell the switch that the microcode is loaded */ 767 gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_MC_VALID, 768 GSWIP_PCE_GCTRL_0); 769 770 return 0; 771 } 772 773 static int gswip_port_vlan_filtering(struct dsa_switch *ds, int port, 774 bool vlan_filtering, 775 struct netlink_ext_ack *extack) 776 { 777 struct net_device *bridge = dsa_port_bridge_dev_get(dsa_to_port(ds, port)); 778 struct gswip_priv *priv = ds->priv; 779 780 /* Do not allow changing the VLAN filtering options while in bridge */ 781 if (bridge && !!(priv->port_vlan_filter & BIT(port)) != vlan_filtering) { 782 NL_SET_ERR_MSG_MOD(extack, 783 "Dynamic toggling of vlan_filtering not supported"); 784 return -EIO; 785 } 786 787 if (vlan_filtering) { 788 /* Use port based VLAN tag */ 789 gswip_switch_mask(priv, 790 GSWIP_PCE_VCTRL_VSR, 791 GSWIP_PCE_VCTRL_UVR | GSWIP_PCE_VCTRL_VIMR | 792 GSWIP_PCE_VCTRL_VEMR, 793 GSWIP_PCE_VCTRL(port)); 794 gswip_switch_mask(priv, GSWIP_PCE_PCTRL_0_TVM, 0, 795 GSWIP_PCE_PCTRL_0p(port)); 796 } else { 797 /* Use port based VLAN tag */ 798 gswip_switch_mask(priv, 799 GSWIP_PCE_VCTRL_UVR | GSWIP_PCE_VCTRL_VIMR | 800 GSWIP_PCE_VCTRL_VEMR, 801 GSWIP_PCE_VCTRL_VSR, 802 GSWIP_PCE_VCTRL(port)); 803 gswip_switch_mask(priv, 0, GSWIP_PCE_PCTRL_0_TVM, 804 GSWIP_PCE_PCTRL_0p(port)); 805 } 806 807 return 0; 808 } 809 810 static int gswip_setup(struct dsa_switch *ds) 811 { 812 struct gswip_priv *priv = ds->priv; 813 unsigned int cpu_port = priv->hw_info->cpu_port; 814 int i; 815 int err; 816 817 gswip_switch_w(priv, GSWIP_SWRES_R0, GSWIP_SWRES); 818 usleep_range(5000, 10000); 819 gswip_switch_w(priv, 0, GSWIP_SWRES); 820 821 /* disable port fetch/store dma on all ports */ 822 for (i = 0; i < priv->hw_info->max_ports; i++) { 823 gswip_port_disable(ds, i); 824 gswip_port_vlan_filtering(ds, i, false, NULL); 825 } 826 827 /* enable Switch */ 828 gswip_mdio_mask(priv, 0, GSWIP_MDIO_GLOB_ENABLE, GSWIP_MDIO_GLOB); 829 830 err = gswip_pce_load_microcode(priv); 831 if (err) { 832 dev_err(priv->dev, "writing PCE microcode failed, %i", err); 833 return err; 834 } 835 836 /* Default unknown Broadcast/Multicast/Unicast port maps */ 837 gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP1); 838 gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP2); 839 gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP3); 840 841 /* Deactivate MDIO PHY auto polling. Some PHYs as the AR8030 have an 842 * interoperability problem with this auto polling mechanism because 843 * their status registers think that the link is in a different state 844 * than it actually is. For the AR8030 it has the BMSR_ESTATEN bit set 845 * as well as ESTATUS_1000_TFULL and ESTATUS_1000_XFULL. This makes the 846 * auto polling state machine consider the link being negotiated with 847 * 1Gbit/s. Since the PHY itself is a Fast Ethernet RMII PHY this leads 848 * to the switch port being completely dead (RX and TX are both not 849 * working). 850 * Also with various other PHY / port combinations (PHY11G GPHY, PHY22F 851 * GPHY, external RGMII PEF7071/7072) any traffic would stop. Sometimes 852 * it would work fine for a few minutes to hours and then stop, on 853 * other device it would no traffic could be sent or received at all. 854 * Testing shows that when PHY auto polling is disabled these problems 855 * go away. 856 */ 857 gswip_mdio_w(priv, 0x0, GSWIP_MDIO_MDC_CFG0); 858 859 /* Configure the MDIO Clock 2.5 MHz */ 860 gswip_mdio_mask(priv, 0xff, 0x09, GSWIP_MDIO_MDC_CFG1); 861 862 /* Disable the xMII interface and clear it's isolation bit */ 863 for (i = 0; i < priv->hw_info->max_ports; i++) 864 gswip_mii_mask_cfg(priv, 865 GSWIP_MII_CFG_EN | GSWIP_MII_CFG_ISOLATE, 866 0, i); 867 868 /* enable special tag insertion on cpu port */ 869 gswip_switch_mask(priv, 0, GSWIP_FDMA_PCTRL_STEN, 870 GSWIP_FDMA_PCTRLp(cpu_port)); 871 872 /* accept special tag in ingress direction */ 873 gswip_switch_mask(priv, 0, GSWIP_PCE_PCTRL_0_INGRESS, 874 GSWIP_PCE_PCTRL_0p(cpu_port)); 875 876 gswip_switch_mask(priv, 0, GSWIP_BM_QUEUE_GCTRL_GL_MOD, 877 GSWIP_BM_QUEUE_GCTRL); 878 879 /* VLAN aware Switching */ 880 gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_VLAN, GSWIP_PCE_GCTRL_0); 881 882 /* Flush MAC Table */ 883 gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_MTFL, GSWIP_PCE_GCTRL_0); 884 885 err = gswip_switch_r_timeout(priv, GSWIP_PCE_GCTRL_0, 886 GSWIP_PCE_GCTRL_0_MTFL); 887 if (err) { 888 dev_err(priv->dev, "MAC flushing didn't finish\n"); 889 return err; 890 } 891 892 ds->mtu_enforcement_ingress = true; 893 894 gswip_port_enable(ds, cpu_port, NULL); 895 896 ds->configure_vlan_while_not_filtering = false; 897 898 return 0; 899 } 900 901 static enum dsa_tag_protocol gswip_get_tag_protocol(struct dsa_switch *ds, 902 int port, 903 enum dsa_tag_protocol mp) 904 { 905 return DSA_TAG_PROTO_GSWIP; 906 } 907 908 static int gswip_vlan_active_create(struct gswip_priv *priv, 909 struct net_device *bridge, 910 int fid, u16 vid) 911 { 912 struct gswip_pce_table_entry vlan_active = {0,}; 913 unsigned int max_ports = priv->hw_info->max_ports; 914 int idx = -1; 915 int err; 916 int i; 917 918 /* Look for a free slot */ 919 for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { 920 if (!priv->vlans[i].bridge) { 921 idx = i; 922 break; 923 } 924 } 925 926 if (idx == -1) 927 return -ENOSPC; 928 929 if (fid == -1) 930 fid = idx; 931 932 vlan_active.index = idx; 933 vlan_active.table = GSWIP_TABLE_ACTIVE_VLAN; 934 vlan_active.key[0] = vid; 935 vlan_active.val[0] = fid; 936 vlan_active.valid = true; 937 938 err = gswip_pce_table_entry_write(priv, &vlan_active); 939 if (err) { 940 dev_err(priv->dev, "failed to write active VLAN: %d\n", err); 941 return err; 942 } 943 944 priv->vlans[idx].bridge = bridge; 945 priv->vlans[idx].vid = vid; 946 priv->vlans[idx].fid = fid; 947 948 return idx; 949 } 950 951 static int gswip_vlan_active_remove(struct gswip_priv *priv, int idx) 952 { 953 struct gswip_pce_table_entry vlan_active = {0,}; 954 int err; 955 956 vlan_active.index = idx; 957 vlan_active.table = GSWIP_TABLE_ACTIVE_VLAN; 958 vlan_active.valid = false; 959 err = gswip_pce_table_entry_write(priv, &vlan_active); 960 if (err) 961 dev_err(priv->dev, "failed to delete active VLAN: %d\n", err); 962 priv->vlans[idx].bridge = NULL; 963 964 return err; 965 } 966 967 static int gswip_vlan_add_unaware(struct gswip_priv *priv, 968 struct net_device *bridge, int port) 969 { 970 struct gswip_pce_table_entry vlan_mapping = {0,}; 971 unsigned int max_ports = priv->hw_info->max_ports; 972 unsigned int cpu_port = priv->hw_info->cpu_port; 973 bool active_vlan_created = false; 974 int idx = -1; 975 int i; 976 int err; 977 978 /* Check if there is already a page for this bridge */ 979 for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { 980 if (priv->vlans[i].bridge == bridge) { 981 idx = i; 982 break; 983 } 984 } 985 986 /* If this bridge is not programmed yet, add a Active VLAN table 987 * entry in a free slot and prepare the VLAN mapping table entry. 988 */ 989 if (idx == -1) { 990 idx = gswip_vlan_active_create(priv, bridge, -1, 0); 991 if (idx < 0) 992 return idx; 993 active_vlan_created = true; 994 995 vlan_mapping.index = idx; 996 vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; 997 /* VLAN ID byte, maps to the VLAN ID of vlan active table */ 998 vlan_mapping.val[0] = 0; 999 } else { 1000 /* Read the existing VLAN mapping entry from the switch */ 1001 vlan_mapping.index = idx; 1002 vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; 1003 err = gswip_pce_table_entry_read(priv, &vlan_mapping); 1004 if (err) { 1005 dev_err(priv->dev, "failed to read VLAN mapping: %d\n", 1006 err); 1007 return err; 1008 } 1009 } 1010 1011 /* Update the VLAN mapping entry and write it to the switch */ 1012 vlan_mapping.val[1] |= BIT(cpu_port); 1013 vlan_mapping.val[1] |= BIT(port); 1014 err = gswip_pce_table_entry_write(priv, &vlan_mapping); 1015 if (err) { 1016 dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err); 1017 /* In case an Active VLAN was creaetd delete it again */ 1018 if (active_vlan_created) 1019 gswip_vlan_active_remove(priv, idx); 1020 return err; 1021 } 1022 1023 gswip_switch_w(priv, 0, GSWIP_PCE_DEFPVID(port)); 1024 return 0; 1025 } 1026 1027 static int gswip_vlan_add_aware(struct gswip_priv *priv, 1028 struct net_device *bridge, int port, 1029 u16 vid, bool untagged, 1030 bool pvid) 1031 { 1032 struct gswip_pce_table_entry vlan_mapping = {0,}; 1033 unsigned int max_ports = priv->hw_info->max_ports; 1034 unsigned int cpu_port = priv->hw_info->cpu_port; 1035 bool active_vlan_created = false; 1036 int idx = -1; 1037 int fid = -1; 1038 int i; 1039 int err; 1040 1041 /* Check if there is already a page for this bridge */ 1042 for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { 1043 if (priv->vlans[i].bridge == bridge) { 1044 if (fid != -1 && fid != priv->vlans[i].fid) 1045 dev_err(priv->dev, "one bridge with multiple flow ids\n"); 1046 fid = priv->vlans[i].fid; 1047 if (priv->vlans[i].vid == vid) { 1048 idx = i; 1049 break; 1050 } 1051 } 1052 } 1053 1054 /* If this bridge is not programmed yet, add a Active VLAN table 1055 * entry in a free slot and prepare the VLAN mapping table entry. 1056 */ 1057 if (idx == -1) { 1058 idx = gswip_vlan_active_create(priv, bridge, fid, vid); 1059 if (idx < 0) 1060 return idx; 1061 active_vlan_created = true; 1062 1063 vlan_mapping.index = idx; 1064 vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; 1065 /* VLAN ID byte, maps to the VLAN ID of vlan active table */ 1066 vlan_mapping.val[0] = vid; 1067 } else { 1068 /* Read the existing VLAN mapping entry from the switch */ 1069 vlan_mapping.index = idx; 1070 vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; 1071 err = gswip_pce_table_entry_read(priv, &vlan_mapping); 1072 if (err) { 1073 dev_err(priv->dev, "failed to read VLAN mapping: %d\n", 1074 err); 1075 return err; 1076 } 1077 } 1078 1079 vlan_mapping.val[0] = vid; 1080 /* Update the VLAN mapping entry and write it to the switch */ 1081 vlan_mapping.val[1] |= BIT(cpu_port); 1082 vlan_mapping.val[2] |= BIT(cpu_port); 1083 vlan_mapping.val[1] |= BIT(port); 1084 if (untagged) 1085 vlan_mapping.val[2] &= ~BIT(port); 1086 else 1087 vlan_mapping.val[2] |= BIT(port); 1088 err = gswip_pce_table_entry_write(priv, &vlan_mapping); 1089 if (err) { 1090 dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err); 1091 /* In case an Active VLAN was creaetd delete it again */ 1092 if (active_vlan_created) 1093 gswip_vlan_active_remove(priv, idx); 1094 return err; 1095 } 1096 1097 if (pvid) 1098 gswip_switch_w(priv, idx, GSWIP_PCE_DEFPVID(port)); 1099 1100 return 0; 1101 } 1102 1103 static int gswip_vlan_remove(struct gswip_priv *priv, 1104 struct net_device *bridge, int port, 1105 u16 vid, bool pvid, bool vlan_aware) 1106 { 1107 struct gswip_pce_table_entry vlan_mapping = {0,}; 1108 unsigned int max_ports = priv->hw_info->max_ports; 1109 unsigned int cpu_port = priv->hw_info->cpu_port; 1110 int idx = -1; 1111 int i; 1112 int err; 1113 1114 /* Check if there is already a page for this bridge */ 1115 for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { 1116 if (priv->vlans[i].bridge == bridge && 1117 (!vlan_aware || priv->vlans[i].vid == vid)) { 1118 idx = i; 1119 break; 1120 } 1121 } 1122 1123 if (idx == -1) { 1124 dev_err(priv->dev, "bridge to leave does not exists\n"); 1125 return -ENOENT; 1126 } 1127 1128 vlan_mapping.index = idx; 1129 vlan_mapping.table = GSWIP_TABLE_VLAN_MAPPING; 1130 err = gswip_pce_table_entry_read(priv, &vlan_mapping); 1131 if (err) { 1132 dev_err(priv->dev, "failed to read VLAN mapping: %d\n", err); 1133 return err; 1134 } 1135 1136 vlan_mapping.val[1] &= ~BIT(port); 1137 vlan_mapping.val[2] &= ~BIT(port); 1138 err = gswip_pce_table_entry_write(priv, &vlan_mapping); 1139 if (err) { 1140 dev_err(priv->dev, "failed to write VLAN mapping: %d\n", err); 1141 return err; 1142 } 1143 1144 /* In case all ports are removed from the bridge, remove the VLAN */ 1145 if ((vlan_mapping.val[1] & ~BIT(cpu_port)) == 0) { 1146 err = gswip_vlan_active_remove(priv, idx); 1147 if (err) { 1148 dev_err(priv->dev, "failed to write active VLAN: %d\n", 1149 err); 1150 return err; 1151 } 1152 } 1153 1154 /* GSWIP 2.2 (GRX300) and later program here the VID directly. */ 1155 if (pvid) 1156 gswip_switch_w(priv, 0, GSWIP_PCE_DEFPVID(port)); 1157 1158 return 0; 1159 } 1160 1161 static int gswip_port_bridge_join(struct dsa_switch *ds, int port, 1162 struct dsa_bridge bridge, 1163 bool *tx_fwd_offload, 1164 struct netlink_ext_ack *extack) 1165 { 1166 struct net_device *br = bridge.dev; 1167 struct gswip_priv *priv = ds->priv; 1168 int err; 1169 1170 /* When the bridge uses VLAN filtering we have to configure VLAN 1171 * specific bridges. No bridge is configured here. 1172 */ 1173 if (!br_vlan_enabled(br)) { 1174 err = gswip_vlan_add_unaware(priv, br, port); 1175 if (err) 1176 return err; 1177 priv->port_vlan_filter &= ~BIT(port); 1178 } else { 1179 priv->port_vlan_filter |= BIT(port); 1180 } 1181 return gswip_add_single_port_br(priv, port, false); 1182 } 1183 1184 static void gswip_port_bridge_leave(struct dsa_switch *ds, int port, 1185 struct dsa_bridge bridge) 1186 { 1187 struct net_device *br = bridge.dev; 1188 struct gswip_priv *priv = ds->priv; 1189 1190 gswip_add_single_port_br(priv, port, true); 1191 1192 /* When the bridge uses VLAN filtering we have to configure VLAN 1193 * specific bridges. No bridge is configured here. 1194 */ 1195 if (!br_vlan_enabled(br)) 1196 gswip_vlan_remove(priv, br, port, 0, true, false); 1197 } 1198 1199 static int gswip_port_vlan_prepare(struct dsa_switch *ds, int port, 1200 const struct switchdev_obj_port_vlan *vlan, 1201 struct netlink_ext_ack *extack) 1202 { 1203 struct net_device *bridge = dsa_port_bridge_dev_get(dsa_to_port(ds, port)); 1204 struct gswip_priv *priv = ds->priv; 1205 unsigned int max_ports = priv->hw_info->max_ports; 1206 int pos = max_ports; 1207 int i, idx = -1; 1208 1209 /* We only support VLAN filtering on bridges */ 1210 if (!dsa_is_cpu_port(ds, port) && !bridge) 1211 return -EOPNOTSUPP; 1212 1213 /* Check if there is already a page for this VLAN */ 1214 for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { 1215 if (priv->vlans[i].bridge == bridge && 1216 priv->vlans[i].vid == vlan->vid) { 1217 idx = i; 1218 break; 1219 } 1220 } 1221 1222 /* If this VLAN is not programmed yet, we have to reserve 1223 * one entry in the VLAN table. Make sure we start at the 1224 * next position round. 1225 */ 1226 if (idx == -1) { 1227 /* Look for a free slot */ 1228 for (; pos < ARRAY_SIZE(priv->vlans); pos++) { 1229 if (!priv->vlans[pos].bridge) { 1230 idx = pos; 1231 pos++; 1232 break; 1233 } 1234 } 1235 1236 if (idx == -1) { 1237 NL_SET_ERR_MSG_MOD(extack, "No slot in VLAN table"); 1238 return -ENOSPC; 1239 } 1240 } 1241 1242 return 0; 1243 } 1244 1245 static int gswip_port_vlan_add(struct dsa_switch *ds, int port, 1246 const struct switchdev_obj_port_vlan *vlan, 1247 struct netlink_ext_ack *extack) 1248 { 1249 struct net_device *bridge = dsa_port_bridge_dev_get(dsa_to_port(ds, port)); 1250 struct gswip_priv *priv = ds->priv; 1251 bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED; 1252 bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID; 1253 int err; 1254 1255 err = gswip_port_vlan_prepare(ds, port, vlan, extack); 1256 if (err) 1257 return err; 1258 1259 /* We have to receive all packets on the CPU port and should not 1260 * do any VLAN filtering here. This is also called with bridge 1261 * NULL and then we do not know for which bridge to configure 1262 * this. 1263 */ 1264 if (dsa_is_cpu_port(ds, port)) 1265 return 0; 1266 1267 return gswip_vlan_add_aware(priv, bridge, port, vlan->vid, 1268 untagged, pvid); 1269 } 1270 1271 static int gswip_port_vlan_del(struct dsa_switch *ds, int port, 1272 const struct switchdev_obj_port_vlan *vlan) 1273 { 1274 struct net_device *bridge = dsa_port_bridge_dev_get(dsa_to_port(ds, port)); 1275 struct gswip_priv *priv = ds->priv; 1276 bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID; 1277 1278 /* We have to receive all packets on the CPU port and should not 1279 * do any VLAN filtering here. This is also called with bridge 1280 * NULL and then we do not know for which bridge to configure 1281 * this. 1282 */ 1283 if (dsa_is_cpu_port(ds, port)) 1284 return 0; 1285 1286 return gswip_vlan_remove(priv, bridge, port, vlan->vid, pvid, true); 1287 } 1288 1289 static void gswip_port_fast_age(struct dsa_switch *ds, int port) 1290 { 1291 struct gswip_priv *priv = ds->priv; 1292 struct gswip_pce_table_entry mac_bridge = {0,}; 1293 int i; 1294 int err; 1295 1296 for (i = 0; i < 2048; i++) { 1297 mac_bridge.table = GSWIP_TABLE_MAC_BRIDGE; 1298 mac_bridge.index = i; 1299 1300 err = gswip_pce_table_entry_read(priv, &mac_bridge); 1301 if (err) { 1302 dev_err(priv->dev, "failed to read mac bridge: %d\n", 1303 err); 1304 return; 1305 } 1306 1307 if (!mac_bridge.valid) 1308 continue; 1309 1310 if (mac_bridge.val[1] & GSWIP_TABLE_MAC_BRIDGE_STATIC) 1311 continue; 1312 1313 if (((mac_bridge.val[0] & GENMASK(7, 4)) >> 4) != port) 1314 continue; 1315 1316 mac_bridge.valid = false; 1317 err = gswip_pce_table_entry_write(priv, &mac_bridge); 1318 if (err) { 1319 dev_err(priv->dev, "failed to write mac bridge: %d\n", 1320 err); 1321 return; 1322 } 1323 } 1324 } 1325 1326 static void gswip_port_stp_state_set(struct dsa_switch *ds, int port, u8 state) 1327 { 1328 struct gswip_priv *priv = ds->priv; 1329 u32 stp_state; 1330 1331 switch (state) { 1332 case BR_STATE_DISABLED: 1333 gswip_switch_mask(priv, GSWIP_SDMA_PCTRL_EN, 0, 1334 GSWIP_SDMA_PCTRLp(port)); 1335 return; 1336 case BR_STATE_BLOCKING: 1337 case BR_STATE_LISTENING: 1338 stp_state = GSWIP_PCE_PCTRL_0_PSTATE_LISTEN; 1339 break; 1340 case BR_STATE_LEARNING: 1341 stp_state = GSWIP_PCE_PCTRL_0_PSTATE_LEARNING; 1342 break; 1343 case BR_STATE_FORWARDING: 1344 stp_state = GSWIP_PCE_PCTRL_0_PSTATE_FORWARDING; 1345 break; 1346 default: 1347 dev_err(priv->dev, "invalid STP state: %d\n", state); 1348 return; 1349 } 1350 1351 gswip_switch_mask(priv, 0, GSWIP_SDMA_PCTRL_EN, 1352 GSWIP_SDMA_PCTRLp(port)); 1353 gswip_switch_mask(priv, GSWIP_PCE_PCTRL_0_PSTATE_MASK, stp_state, 1354 GSWIP_PCE_PCTRL_0p(port)); 1355 } 1356 1357 static int gswip_port_fdb(struct dsa_switch *ds, int port, 1358 const unsigned char *addr, u16 vid, bool add) 1359 { 1360 struct net_device *bridge = dsa_port_bridge_dev_get(dsa_to_port(ds, port)); 1361 struct gswip_priv *priv = ds->priv; 1362 struct gswip_pce_table_entry mac_bridge = {0,}; 1363 unsigned int max_ports = priv->hw_info->max_ports; 1364 int fid = -1; 1365 int i; 1366 int err; 1367 1368 if (!bridge) 1369 return -EINVAL; 1370 1371 for (i = max_ports; i < ARRAY_SIZE(priv->vlans); i++) { 1372 if (priv->vlans[i].bridge == bridge) { 1373 fid = priv->vlans[i].fid; 1374 break; 1375 } 1376 } 1377 1378 if (fid == -1) { 1379 dev_err(priv->dev, "Port not part of a bridge\n"); 1380 return -EINVAL; 1381 } 1382 1383 mac_bridge.table = GSWIP_TABLE_MAC_BRIDGE; 1384 mac_bridge.key_mode = true; 1385 mac_bridge.key[0] = addr[5] | (addr[4] << 8); 1386 mac_bridge.key[1] = addr[3] | (addr[2] << 8); 1387 mac_bridge.key[2] = addr[1] | (addr[0] << 8); 1388 mac_bridge.key[3] = fid; 1389 mac_bridge.val[0] = add ? BIT(port) : 0; /* port map */ 1390 mac_bridge.val[1] = GSWIP_TABLE_MAC_BRIDGE_STATIC; 1391 mac_bridge.valid = add; 1392 1393 err = gswip_pce_table_entry_write(priv, &mac_bridge); 1394 if (err) 1395 dev_err(priv->dev, "failed to write mac bridge: %d\n", err); 1396 1397 return err; 1398 } 1399 1400 static int gswip_port_fdb_add(struct dsa_switch *ds, int port, 1401 const unsigned char *addr, u16 vid, 1402 struct dsa_db db) 1403 { 1404 return gswip_port_fdb(ds, port, addr, vid, true); 1405 } 1406 1407 static int gswip_port_fdb_del(struct dsa_switch *ds, int port, 1408 const unsigned char *addr, u16 vid, 1409 struct dsa_db db) 1410 { 1411 return gswip_port_fdb(ds, port, addr, vid, false); 1412 } 1413 1414 static int gswip_port_fdb_dump(struct dsa_switch *ds, int port, 1415 dsa_fdb_dump_cb_t *cb, void *data) 1416 { 1417 struct gswip_priv *priv = ds->priv; 1418 struct gswip_pce_table_entry mac_bridge = {0,}; 1419 unsigned char addr[6]; 1420 int i; 1421 int err; 1422 1423 for (i = 0; i < 2048; i++) { 1424 mac_bridge.table = GSWIP_TABLE_MAC_BRIDGE; 1425 mac_bridge.index = i; 1426 1427 err = gswip_pce_table_entry_read(priv, &mac_bridge); 1428 if (err) { 1429 dev_err(priv->dev, 1430 "failed to read mac bridge entry %d: %d\n", 1431 i, err); 1432 return err; 1433 } 1434 1435 if (!mac_bridge.valid) 1436 continue; 1437 1438 addr[5] = mac_bridge.key[0] & 0xff; 1439 addr[4] = (mac_bridge.key[0] >> 8) & 0xff; 1440 addr[3] = mac_bridge.key[1] & 0xff; 1441 addr[2] = (mac_bridge.key[1] >> 8) & 0xff; 1442 addr[1] = mac_bridge.key[2] & 0xff; 1443 addr[0] = (mac_bridge.key[2] >> 8) & 0xff; 1444 if (mac_bridge.val[1] & GSWIP_TABLE_MAC_BRIDGE_STATIC) { 1445 if (mac_bridge.val[0] & BIT(port)) { 1446 err = cb(addr, 0, true, data); 1447 if (err) 1448 return err; 1449 } 1450 } else { 1451 if (((mac_bridge.val[0] & GENMASK(7, 4)) >> 4) == port) { 1452 err = cb(addr, 0, false, data); 1453 if (err) 1454 return err; 1455 } 1456 } 1457 } 1458 return 0; 1459 } 1460 1461 static int gswip_port_max_mtu(struct dsa_switch *ds, int port) 1462 { 1463 /* Includes 8 bytes for special header. */ 1464 return GSWIP_MAX_PACKET_LENGTH - VLAN_ETH_HLEN - ETH_FCS_LEN; 1465 } 1466 1467 static int gswip_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu) 1468 { 1469 struct gswip_priv *priv = ds->priv; 1470 int cpu_port = priv->hw_info->cpu_port; 1471 1472 /* CPU port always has maximum mtu of user ports, so use it to set 1473 * switch frame size, including 8 byte special header. 1474 */ 1475 if (port == cpu_port) { 1476 new_mtu += 8; 1477 gswip_switch_w(priv, VLAN_ETH_HLEN + new_mtu + ETH_FCS_LEN, 1478 GSWIP_MAC_FLEN); 1479 } 1480 1481 /* Enable MLEN for ports with non-standard MTUs, including the special 1482 * header on the CPU port added above. 1483 */ 1484 if (new_mtu != ETH_DATA_LEN) 1485 gswip_switch_mask(priv, 0, GSWIP_MAC_CTRL_2_MLEN, 1486 GSWIP_MAC_CTRL_2p(port)); 1487 else 1488 gswip_switch_mask(priv, GSWIP_MAC_CTRL_2_MLEN, 0, 1489 GSWIP_MAC_CTRL_2p(port)); 1490 1491 return 0; 1492 } 1493 1494 static void gswip_xrx200_phylink_get_caps(struct dsa_switch *ds, int port, 1495 struct phylink_config *config) 1496 { 1497 switch (port) { 1498 case 0: 1499 case 1: 1500 phy_interface_set_rgmii(config->supported_interfaces); 1501 __set_bit(PHY_INTERFACE_MODE_MII, 1502 config->supported_interfaces); 1503 __set_bit(PHY_INTERFACE_MODE_REVMII, 1504 config->supported_interfaces); 1505 __set_bit(PHY_INTERFACE_MODE_RMII, 1506 config->supported_interfaces); 1507 break; 1508 1509 case 2: 1510 case 3: 1511 case 4: 1512 __set_bit(PHY_INTERFACE_MODE_INTERNAL, 1513 config->supported_interfaces); 1514 break; 1515 1516 case 5: 1517 phy_interface_set_rgmii(config->supported_interfaces); 1518 __set_bit(PHY_INTERFACE_MODE_INTERNAL, 1519 config->supported_interfaces); 1520 break; 1521 } 1522 1523 config->mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | 1524 MAC_10 | MAC_100 | MAC_1000; 1525 } 1526 1527 static void gswip_xrx300_phylink_get_caps(struct dsa_switch *ds, int port, 1528 struct phylink_config *config) 1529 { 1530 switch (port) { 1531 case 0: 1532 phy_interface_set_rgmii(config->supported_interfaces); 1533 __set_bit(PHY_INTERFACE_MODE_GMII, 1534 config->supported_interfaces); 1535 __set_bit(PHY_INTERFACE_MODE_RMII, 1536 config->supported_interfaces); 1537 break; 1538 1539 case 1: 1540 case 2: 1541 case 3: 1542 case 4: 1543 __set_bit(PHY_INTERFACE_MODE_INTERNAL, 1544 config->supported_interfaces); 1545 break; 1546 1547 case 5: 1548 phy_interface_set_rgmii(config->supported_interfaces); 1549 __set_bit(PHY_INTERFACE_MODE_INTERNAL, 1550 config->supported_interfaces); 1551 __set_bit(PHY_INTERFACE_MODE_RMII, 1552 config->supported_interfaces); 1553 break; 1554 } 1555 1556 config->mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | 1557 MAC_10 | MAC_100 | MAC_1000; 1558 } 1559 1560 static void gswip_port_set_link(struct gswip_priv *priv, int port, bool link) 1561 { 1562 u32 mdio_phy; 1563 1564 if (link) 1565 mdio_phy = GSWIP_MDIO_PHY_LINK_UP; 1566 else 1567 mdio_phy = GSWIP_MDIO_PHY_LINK_DOWN; 1568 1569 gswip_mdio_mask(priv, GSWIP_MDIO_PHY_LINK_MASK, mdio_phy, 1570 GSWIP_MDIO_PHYp(port)); 1571 } 1572 1573 static void gswip_port_set_speed(struct gswip_priv *priv, int port, int speed, 1574 phy_interface_t interface) 1575 { 1576 u32 mdio_phy = 0, mii_cfg = 0, mac_ctrl_0 = 0; 1577 1578 switch (speed) { 1579 case SPEED_10: 1580 mdio_phy = GSWIP_MDIO_PHY_SPEED_M10; 1581 1582 if (interface == PHY_INTERFACE_MODE_RMII) 1583 mii_cfg = GSWIP_MII_CFG_RATE_M50; 1584 else 1585 mii_cfg = GSWIP_MII_CFG_RATE_M2P5; 1586 1587 mac_ctrl_0 = GSWIP_MAC_CTRL_0_GMII_MII; 1588 break; 1589 1590 case SPEED_100: 1591 mdio_phy = GSWIP_MDIO_PHY_SPEED_M100; 1592 1593 if (interface == PHY_INTERFACE_MODE_RMII) 1594 mii_cfg = GSWIP_MII_CFG_RATE_M50; 1595 else 1596 mii_cfg = GSWIP_MII_CFG_RATE_M25; 1597 1598 mac_ctrl_0 = GSWIP_MAC_CTRL_0_GMII_MII; 1599 break; 1600 1601 case SPEED_1000: 1602 mdio_phy = GSWIP_MDIO_PHY_SPEED_G1; 1603 1604 mii_cfg = GSWIP_MII_CFG_RATE_M125; 1605 1606 mac_ctrl_0 = GSWIP_MAC_CTRL_0_GMII_RGMII; 1607 break; 1608 } 1609 1610 gswip_mdio_mask(priv, GSWIP_MDIO_PHY_SPEED_MASK, mdio_phy, 1611 GSWIP_MDIO_PHYp(port)); 1612 gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_RATE_MASK, mii_cfg, port); 1613 gswip_switch_mask(priv, GSWIP_MAC_CTRL_0_GMII_MASK, mac_ctrl_0, 1614 GSWIP_MAC_CTRL_0p(port)); 1615 } 1616 1617 static void gswip_port_set_duplex(struct gswip_priv *priv, int port, int duplex) 1618 { 1619 u32 mac_ctrl_0, mdio_phy; 1620 1621 if (duplex == DUPLEX_FULL) { 1622 mac_ctrl_0 = GSWIP_MAC_CTRL_0_FDUP_EN; 1623 mdio_phy = GSWIP_MDIO_PHY_FDUP_EN; 1624 } else { 1625 mac_ctrl_0 = GSWIP_MAC_CTRL_0_FDUP_DIS; 1626 mdio_phy = GSWIP_MDIO_PHY_FDUP_DIS; 1627 } 1628 1629 gswip_switch_mask(priv, GSWIP_MAC_CTRL_0_FDUP_MASK, mac_ctrl_0, 1630 GSWIP_MAC_CTRL_0p(port)); 1631 gswip_mdio_mask(priv, GSWIP_MDIO_PHY_FDUP_MASK, mdio_phy, 1632 GSWIP_MDIO_PHYp(port)); 1633 } 1634 1635 static void gswip_port_set_pause(struct gswip_priv *priv, int port, 1636 bool tx_pause, bool rx_pause) 1637 { 1638 u32 mac_ctrl_0, mdio_phy; 1639 1640 if (tx_pause && rx_pause) { 1641 mac_ctrl_0 = GSWIP_MAC_CTRL_0_FCON_RXTX; 1642 mdio_phy = GSWIP_MDIO_PHY_FCONTX_EN | 1643 GSWIP_MDIO_PHY_FCONRX_EN; 1644 } else if (tx_pause) { 1645 mac_ctrl_0 = GSWIP_MAC_CTRL_0_FCON_TX; 1646 mdio_phy = GSWIP_MDIO_PHY_FCONTX_EN | 1647 GSWIP_MDIO_PHY_FCONRX_DIS; 1648 } else if (rx_pause) { 1649 mac_ctrl_0 = GSWIP_MAC_CTRL_0_FCON_RX; 1650 mdio_phy = GSWIP_MDIO_PHY_FCONTX_DIS | 1651 GSWIP_MDIO_PHY_FCONRX_EN; 1652 } else { 1653 mac_ctrl_0 = GSWIP_MAC_CTRL_0_FCON_NONE; 1654 mdio_phy = GSWIP_MDIO_PHY_FCONTX_DIS | 1655 GSWIP_MDIO_PHY_FCONRX_DIS; 1656 } 1657 1658 gswip_switch_mask(priv, GSWIP_MAC_CTRL_0_FCON_MASK, 1659 mac_ctrl_0, GSWIP_MAC_CTRL_0p(port)); 1660 gswip_mdio_mask(priv, 1661 GSWIP_MDIO_PHY_FCONTX_MASK | 1662 GSWIP_MDIO_PHY_FCONRX_MASK, 1663 mdio_phy, GSWIP_MDIO_PHYp(port)); 1664 } 1665 1666 static void gswip_phylink_mac_config(struct dsa_switch *ds, int port, 1667 unsigned int mode, 1668 const struct phylink_link_state *state) 1669 { 1670 struct gswip_priv *priv = ds->priv; 1671 u32 miicfg = 0; 1672 1673 miicfg |= GSWIP_MII_CFG_LDCLKDIS; 1674 1675 switch (state->interface) { 1676 case PHY_INTERFACE_MODE_MII: 1677 case PHY_INTERFACE_MODE_INTERNAL: 1678 miicfg |= GSWIP_MII_CFG_MODE_MIIM; 1679 break; 1680 case PHY_INTERFACE_MODE_REVMII: 1681 miicfg |= GSWIP_MII_CFG_MODE_MIIP; 1682 break; 1683 case PHY_INTERFACE_MODE_RMII: 1684 miicfg |= GSWIP_MII_CFG_MODE_RMIIM; 1685 break; 1686 case PHY_INTERFACE_MODE_RGMII: 1687 case PHY_INTERFACE_MODE_RGMII_ID: 1688 case PHY_INTERFACE_MODE_RGMII_RXID: 1689 case PHY_INTERFACE_MODE_RGMII_TXID: 1690 miicfg |= GSWIP_MII_CFG_MODE_RGMII; 1691 break; 1692 case PHY_INTERFACE_MODE_GMII: 1693 miicfg |= GSWIP_MII_CFG_MODE_GMII; 1694 break; 1695 default: 1696 dev_err(ds->dev, 1697 "Unsupported interface: %d\n", state->interface); 1698 return; 1699 } 1700 1701 gswip_mii_mask_cfg(priv, 1702 GSWIP_MII_CFG_MODE_MASK | GSWIP_MII_CFG_RMII_CLK | 1703 GSWIP_MII_CFG_RGMII_IBS | GSWIP_MII_CFG_LDCLKDIS, 1704 miicfg, port); 1705 1706 switch (state->interface) { 1707 case PHY_INTERFACE_MODE_RGMII_ID: 1708 gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_TXDLY_MASK | 1709 GSWIP_MII_PCDU_RXDLY_MASK, 0, port); 1710 break; 1711 case PHY_INTERFACE_MODE_RGMII_RXID: 1712 gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_RXDLY_MASK, 0, port); 1713 break; 1714 case PHY_INTERFACE_MODE_RGMII_TXID: 1715 gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_TXDLY_MASK, 0, port); 1716 break; 1717 default: 1718 break; 1719 } 1720 } 1721 1722 static void gswip_phylink_mac_link_down(struct dsa_switch *ds, int port, 1723 unsigned int mode, 1724 phy_interface_t interface) 1725 { 1726 struct gswip_priv *priv = ds->priv; 1727 1728 gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, port); 1729 1730 if (!dsa_is_cpu_port(ds, port)) 1731 gswip_port_set_link(priv, port, false); 1732 } 1733 1734 static void gswip_phylink_mac_link_up(struct dsa_switch *ds, int port, 1735 unsigned int mode, 1736 phy_interface_t interface, 1737 struct phy_device *phydev, 1738 int speed, int duplex, 1739 bool tx_pause, bool rx_pause) 1740 { 1741 struct gswip_priv *priv = ds->priv; 1742 1743 if (!dsa_is_cpu_port(ds, port)) { 1744 gswip_port_set_link(priv, port, true); 1745 gswip_port_set_speed(priv, port, speed, interface); 1746 gswip_port_set_duplex(priv, port, duplex); 1747 gswip_port_set_pause(priv, port, tx_pause, rx_pause); 1748 } 1749 1750 gswip_mii_mask_cfg(priv, 0, GSWIP_MII_CFG_EN, port); 1751 } 1752 1753 static void gswip_get_strings(struct dsa_switch *ds, int port, u32 stringset, 1754 uint8_t *data) 1755 { 1756 int i; 1757 1758 if (stringset != ETH_SS_STATS) 1759 return; 1760 1761 for (i = 0; i < ARRAY_SIZE(gswip_rmon_cnt); i++) 1762 strncpy(data + i * ETH_GSTRING_LEN, gswip_rmon_cnt[i].name, 1763 ETH_GSTRING_LEN); 1764 } 1765 1766 static u32 gswip_bcm_ram_entry_read(struct gswip_priv *priv, u32 table, 1767 u32 index) 1768 { 1769 u32 result; 1770 int err; 1771 1772 gswip_switch_w(priv, index, GSWIP_BM_RAM_ADDR); 1773 gswip_switch_mask(priv, GSWIP_BM_RAM_CTRL_ADDR_MASK | 1774 GSWIP_BM_RAM_CTRL_OPMOD, 1775 table | GSWIP_BM_RAM_CTRL_BAS, 1776 GSWIP_BM_RAM_CTRL); 1777 1778 err = gswip_switch_r_timeout(priv, GSWIP_BM_RAM_CTRL, 1779 GSWIP_BM_RAM_CTRL_BAS); 1780 if (err) { 1781 dev_err(priv->dev, "timeout while reading table: %u, index: %u", 1782 table, index); 1783 return 0; 1784 } 1785 1786 result = gswip_switch_r(priv, GSWIP_BM_RAM_VAL(0)); 1787 result |= gswip_switch_r(priv, GSWIP_BM_RAM_VAL(1)) << 16; 1788 1789 return result; 1790 } 1791 1792 static void gswip_get_ethtool_stats(struct dsa_switch *ds, int port, 1793 uint64_t *data) 1794 { 1795 struct gswip_priv *priv = ds->priv; 1796 const struct gswip_rmon_cnt_desc *rmon_cnt; 1797 int i; 1798 u64 high; 1799 1800 for (i = 0; i < ARRAY_SIZE(gswip_rmon_cnt); i++) { 1801 rmon_cnt = &gswip_rmon_cnt[i]; 1802 1803 data[i] = gswip_bcm_ram_entry_read(priv, port, 1804 rmon_cnt->offset); 1805 if (rmon_cnt->size == 2) { 1806 high = gswip_bcm_ram_entry_read(priv, port, 1807 rmon_cnt->offset + 1); 1808 data[i] |= high << 32; 1809 } 1810 } 1811 } 1812 1813 static int gswip_get_sset_count(struct dsa_switch *ds, int port, int sset) 1814 { 1815 if (sset != ETH_SS_STATS) 1816 return 0; 1817 1818 return ARRAY_SIZE(gswip_rmon_cnt); 1819 } 1820 1821 static const struct dsa_switch_ops gswip_xrx200_switch_ops = { 1822 .get_tag_protocol = gswip_get_tag_protocol, 1823 .setup = gswip_setup, 1824 .port_enable = gswip_port_enable, 1825 .port_disable = gswip_port_disable, 1826 .port_bridge_join = gswip_port_bridge_join, 1827 .port_bridge_leave = gswip_port_bridge_leave, 1828 .port_fast_age = gswip_port_fast_age, 1829 .port_vlan_filtering = gswip_port_vlan_filtering, 1830 .port_vlan_add = gswip_port_vlan_add, 1831 .port_vlan_del = gswip_port_vlan_del, 1832 .port_stp_state_set = gswip_port_stp_state_set, 1833 .port_fdb_add = gswip_port_fdb_add, 1834 .port_fdb_del = gswip_port_fdb_del, 1835 .port_fdb_dump = gswip_port_fdb_dump, 1836 .port_change_mtu = gswip_port_change_mtu, 1837 .port_max_mtu = gswip_port_max_mtu, 1838 .phylink_get_caps = gswip_xrx200_phylink_get_caps, 1839 .phylink_mac_config = gswip_phylink_mac_config, 1840 .phylink_mac_link_down = gswip_phylink_mac_link_down, 1841 .phylink_mac_link_up = gswip_phylink_mac_link_up, 1842 .get_strings = gswip_get_strings, 1843 .get_ethtool_stats = gswip_get_ethtool_stats, 1844 .get_sset_count = gswip_get_sset_count, 1845 }; 1846 1847 static const struct dsa_switch_ops gswip_xrx300_switch_ops = { 1848 .get_tag_protocol = gswip_get_tag_protocol, 1849 .setup = gswip_setup, 1850 .port_enable = gswip_port_enable, 1851 .port_disable = gswip_port_disable, 1852 .port_bridge_join = gswip_port_bridge_join, 1853 .port_bridge_leave = gswip_port_bridge_leave, 1854 .port_fast_age = gswip_port_fast_age, 1855 .port_vlan_filtering = gswip_port_vlan_filtering, 1856 .port_vlan_add = gswip_port_vlan_add, 1857 .port_vlan_del = gswip_port_vlan_del, 1858 .port_stp_state_set = gswip_port_stp_state_set, 1859 .port_fdb_add = gswip_port_fdb_add, 1860 .port_fdb_del = gswip_port_fdb_del, 1861 .port_fdb_dump = gswip_port_fdb_dump, 1862 .port_change_mtu = gswip_port_change_mtu, 1863 .port_max_mtu = gswip_port_max_mtu, 1864 .phylink_get_caps = gswip_xrx300_phylink_get_caps, 1865 .phylink_mac_config = gswip_phylink_mac_config, 1866 .phylink_mac_link_down = gswip_phylink_mac_link_down, 1867 .phylink_mac_link_up = gswip_phylink_mac_link_up, 1868 .get_strings = gswip_get_strings, 1869 .get_ethtool_stats = gswip_get_ethtool_stats, 1870 .get_sset_count = gswip_get_sset_count, 1871 }; 1872 1873 static const struct xway_gphy_match_data xrx200a1x_gphy_data = { 1874 .fe_firmware_name = "lantiq/xrx200_phy22f_a14.bin", 1875 .ge_firmware_name = "lantiq/xrx200_phy11g_a14.bin", 1876 }; 1877 1878 static const struct xway_gphy_match_data xrx200a2x_gphy_data = { 1879 .fe_firmware_name = "lantiq/xrx200_phy22f_a22.bin", 1880 .ge_firmware_name = "lantiq/xrx200_phy11g_a22.bin", 1881 }; 1882 1883 static const struct xway_gphy_match_data xrx300_gphy_data = { 1884 .fe_firmware_name = "lantiq/xrx300_phy22f_a21.bin", 1885 .ge_firmware_name = "lantiq/xrx300_phy11g_a21.bin", 1886 }; 1887 1888 static const struct of_device_id xway_gphy_match[] = { 1889 { .compatible = "lantiq,xrx200-gphy-fw", .data = NULL }, 1890 { .compatible = "lantiq,xrx200a1x-gphy-fw", .data = &xrx200a1x_gphy_data }, 1891 { .compatible = "lantiq,xrx200a2x-gphy-fw", .data = &xrx200a2x_gphy_data }, 1892 { .compatible = "lantiq,xrx300-gphy-fw", .data = &xrx300_gphy_data }, 1893 { .compatible = "lantiq,xrx330-gphy-fw", .data = &xrx300_gphy_data }, 1894 {}, 1895 }; 1896 1897 static int gswip_gphy_fw_load(struct gswip_priv *priv, struct gswip_gphy_fw *gphy_fw) 1898 { 1899 struct device *dev = priv->dev; 1900 const struct firmware *fw; 1901 void *fw_addr; 1902 dma_addr_t dma_addr; 1903 dma_addr_t dev_addr; 1904 size_t size; 1905 int ret; 1906 1907 ret = clk_prepare_enable(gphy_fw->clk_gate); 1908 if (ret) 1909 return ret; 1910 1911 reset_control_assert(gphy_fw->reset); 1912 1913 /* The vendor BSP uses a 200ms delay after asserting the reset line. 1914 * Without this some users are observing that the PHY is not coming up 1915 * on the MDIO bus. 1916 */ 1917 msleep(200); 1918 1919 ret = request_firmware(&fw, gphy_fw->fw_name, dev); 1920 if (ret) { 1921 dev_err(dev, "failed to load firmware: %s, error: %i\n", 1922 gphy_fw->fw_name, ret); 1923 return ret; 1924 } 1925 1926 /* GPHY cores need the firmware code in a persistent and contiguous 1927 * memory area with a 16 kB boundary aligned start address. 1928 */ 1929 size = fw->size + XRX200_GPHY_FW_ALIGN; 1930 1931 fw_addr = dmam_alloc_coherent(dev, size, &dma_addr, GFP_KERNEL); 1932 if (fw_addr) { 1933 fw_addr = PTR_ALIGN(fw_addr, XRX200_GPHY_FW_ALIGN); 1934 dev_addr = ALIGN(dma_addr, XRX200_GPHY_FW_ALIGN); 1935 memcpy(fw_addr, fw->data, fw->size); 1936 } else { 1937 dev_err(dev, "failed to alloc firmware memory\n"); 1938 release_firmware(fw); 1939 return -ENOMEM; 1940 } 1941 1942 release_firmware(fw); 1943 1944 ret = regmap_write(priv->rcu_regmap, gphy_fw->fw_addr_offset, dev_addr); 1945 if (ret) 1946 return ret; 1947 1948 reset_control_deassert(gphy_fw->reset); 1949 1950 return ret; 1951 } 1952 1953 static int gswip_gphy_fw_probe(struct gswip_priv *priv, 1954 struct gswip_gphy_fw *gphy_fw, 1955 struct device_node *gphy_fw_np, int i) 1956 { 1957 struct device *dev = priv->dev; 1958 u32 gphy_mode; 1959 int ret; 1960 char gphyname[10]; 1961 1962 snprintf(gphyname, sizeof(gphyname), "gphy%d", i); 1963 1964 gphy_fw->clk_gate = devm_clk_get(dev, gphyname); 1965 if (IS_ERR(gphy_fw->clk_gate)) { 1966 dev_err(dev, "Failed to lookup gate clock\n"); 1967 return PTR_ERR(gphy_fw->clk_gate); 1968 } 1969 1970 ret = of_property_read_u32(gphy_fw_np, "reg", &gphy_fw->fw_addr_offset); 1971 if (ret) 1972 return ret; 1973 1974 ret = of_property_read_u32(gphy_fw_np, "lantiq,gphy-mode", &gphy_mode); 1975 /* Default to GE mode */ 1976 if (ret) 1977 gphy_mode = GPHY_MODE_GE; 1978 1979 switch (gphy_mode) { 1980 case GPHY_MODE_FE: 1981 gphy_fw->fw_name = priv->gphy_fw_name_cfg->fe_firmware_name; 1982 break; 1983 case GPHY_MODE_GE: 1984 gphy_fw->fw_name = priv->gphy_fw_name_cfg->ge_firmware_name; 1985 break; 1986 default: 1987 dev_err(dev, "Unknown GPHY mode %d\n", gphy_mode); 1988 return -EINVAL; 1989 } 1990 1991 gphy_fw->reset = of_reset_control_array_get_exclusive(gphy_fw_np); 1992 if (IS_ERR(gphy_fw->reset)) 1993 return dev_err_probe(dev, PTR_ERR(gphy_fw->reset), 1994 "Failed to lookup gphy reset\n"); 1995 1996 return gswip_gphy_fw_load(priv, gphy_fw); 1997 } 1998 1999 static void gswip_gphy_fw_remove(struct gswip_priv *priv, 2000 struct gswip_gphy_fw *gphy_fw) 2001 { 2002 int ret; 2003 2004 /* check if the device was fully probed */ 2005 if (!gphy_fw->fw_name) 2006 return; 2007 2008 ret = regmap_write(priv->rcu_regmap, gphy_fw->fw_addr_offset, 0); 2009 if (ret) 2010 dev_err(priv->dev, "can not reset GPHY FW pointer"); 2011 2012 clk_disable_unprepare(gphy_fw->clk_gate); 2013 2014 reset_control_put(gphy_fw->reset); 2015 } 2016 2017 static int gswip_gphy_fw_list(struct gswip_priv *priv, 2018 struct device_node *gphy_fw_list_np, u32 version) 2019 { 2020 struct device *dev = priv->dev; 2021 struct device_node *gphy_fw_np; 2022 const struct of_device_id *match; 2023 int err; 2024 int i = 0; 2025 2026 /* The VRX200 rev 1.1 uses the GSWIP 2.0 and needs the older 2027 * GPHY firmware. The VRX200 rev 1.2 uses the GSWIP 2.1 and also 2028 * needs a different GPHY firmware. 2029 */ 2030 if (of_device_is_compatible(gphy_fw_list_np, "lantiq,xrx200-gphy-fw")) { 2031 switch (version) { 2032 case GSWIP_VERSION_2_0: 2033 priv->gphy_fw_name_cfg = &xrx200a1x_gphy_data; 2034 break; 2035 case GSWIP_VERSION_2_1: 2036 priv->gphy_fw_name_cfg = &xrx200a2x_gphy_data; 2037 break; 2038 default: 2039 dev_err(dev, "unknown GSWIP version: 0x%x", version); 2040 return -ENOENT; 2041 } 2042 } 2043 2044 match = of_match_node(xway_gphy_match, gphy_fw_list_np); 2045 if (match && match->data) 2046 priv->gphy_fw_name_cfg = match->data; 2047 2048 if (!priv->gphy_fw_name_cfg) { 2049 dev_err(dev, "GPHY compatible type not supported"); 2050 return -ENOENT; 2051 } 2052 2053 priv->num_gphy_fw = of_get_available_child_count(gphy_fw_list_np); 2054 if (!priv->num_gphy_fw) 2055 return -ENOENT; 2056 2057 priv->rcu_regmap = syscon_regmap_lookup_by_phandle(gphy_fw_list_np, 2058 "lantiq,rcu"); 2059 if (IS_ERR(priv->rcu_regmap)) 2060 return PTR_ERR(priv->rcu_regmap); 2061 2062 priv->gphy_fw = devm_kmalloc_array(dev, priv->num_gphy_fw, 2063 sizeof(*priv->gphy_fw), 2064 GFP_KERNEL | __GFP_ZERO); 2065 if (!priv->gphy_fw) 2066 return -ENOMEM; 2067 2068 for_each_available_child_of_node(gphy_fw_list_np, gphy_fw_np) { 2069 err = gswip_gphy_fw_probe(priv, &priv->gphy_fw[i], 2070 gphy_fw_np, i); 2071 if (err) { 2072 of_node_put(gphy_fw_np); 2073 goto remove_gphy; 2074 } 2075 i++; 2076 } 2077 2078 /* The standalone PHY11G requires 300ms to be fully 2079 * initialized and ready for any MDIO communication after being 2080 * taken out of reset. For the SoC-internal GPHY variant there 2081 * is no (known) documentation for the minimum time after a 2082 * reset. Use the same value as for the standalone variant as 2083 * some users have reported internal PHYs not being detected 2084 * without any delay. 2085 */ 2086 msleep(300); 2087 2088 return 0; 2089 2090 remove_gphy: 2091 for (i = 0; i < priv->num_gphy_fw; i++) 2092 gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]); 2093 return err; 2094 } 2095 2096 static int gswip_probe(struct platform_device *pdev) 2097 { 2098 struct gswip_priv *priv; 2099 struct device_node *np, *mdio_np, *gphy_fw_np; 2100 struct device *dev = &pdev->dev; 2101 int err; 2102 int i; 2103 u32 version; 2104 2105 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 2106 if (!priv) 2107 return -ENOMEM; 2108 2109 priv->gswip = devm_platform_ioremap_resource(pdev, 0); 2110 if (IS_ERR(priv->gswip)) 2111 return PTR_ERR(priv->gswip); 2112 2113 priv->mdio = devm_platform_ioremap_resource(pdev, 1); 2114 if (IS_ERR(priv->mdio)) 2115 return PTR_ERR(priv->mdio); 2116 2117 priv->mii = devm_platform_ioremap_resource(pdev, 2); 2118 if (IS_ERR(priv->mii)) 2119 return PTR_ERR(priv->mii); 2120 2121 priv->hw_info = of_device_get_match_data(dev); 2122 if (!priv->hw_info) 2123 return -EINVAL; 2124 2125 priv->ds = devm_kzalloc(dev, sizeof(*priv->ds), GFP_KERNEL); 2126 if (!priv->ds) 2127 return -ENOMEM; 2128 2129 priv->ds->dev = dev; 2130 priv->ds->num_ports = priv->hw_info->max_ports; 2131 priv->ds->priv = priv; 2132 priv->ds->ops = priv->hw_info->ops; 2133 priv->dev = dev; 2134 mutex_init(&priv->pce_table_lock); 2135 version = gswip_switch_r(priv, GSWIP_VERSION); 2136 2137 np = dev->of_node; 2138 switch (version) { 2139 case GSWIP_VERSION_2_0: 2140 case GSWIP_VERSION_2_1: 2141 if (!of_device_is_compatible(np, "lantiq,xrx200-gswip")) 2142 return -EINVAL; 2143 break; 2144 case GSWIP_VERSION_2_2: 2145 case GSWIP_VERSION_2_2_ETC: 2146 if (!of_device_is_compatible(np, "lantiq,xrx300-gswip") && 2147 !of_device_is_compatible(np, "lantiq,xrx330-gswip")) 2148 return -EINVAL; 2149 break; 2150 default: 2151 dev_err(dev, "unknown GSWIP version: 0x%x", version); 2152 return -ENOENT; 2153 } 2154 2155 /* bring up the mdio bus */ 2156 gphy_fw_np = of_get_compatible_child(dev->of_node, "lantiq,gphy-fw"); 2157 if (gphy_fw_np) { 2158 err = gswip_gphy_fw_list(priv, gphy_fw_np, version); 2159 of_node_put(gphy_fw_np); 2160 if (err) { 2161 dev_err(dev, "gphy fw probe failed\n"); 2162 return err; 2163 } 2164 } 2165 2166 /* bring up the mdio bus */ 2167 mdio_np = of_get_compatible_child(dev->of_node, "lantiq,xrx200-mdio"); 2168 if (mdio_np) { 2169 err = gswip_mdio(priv, mdio_np); 2170 if (err) { 2171 dev_err(dev, "mdio probe failed\n"); 2172 goto put_mdio_node; 2173 } 2174 } 2175 2176 err = dsa_register_switch(priv->ds); 2177 if (err) { 2178 dev_err(dev, "dsa switch register failed: %i\n", err); 2179 goto mdio_bus; 2180 } 2181 if (!dsa_is_cpu_port(priv->ds, priv->hw_info->cpu_port)) { 2182 dev_err(dev, "wrong CPU port defined, HW only supports port: %i", 2183 priv->hw_info->cpu_port); 2184 err = -EINVAL; 2185 goto disable_switch; 2186 } 2187 2188 platform_set_drvdata(pdev, priv); 2189 2190 dev_info(dev, "probed GSWIP version %lx mod %lx\n", 2191 (version & GSWIP_VERSION_REV_MASK) >> GSWIP_VERSION_REV_SHIFT, 2192 (version & GSWIP_VERSION_MOD_MASK) >> GSWIP_VERSION_MOD_SHIFT); 2193 return 0; 2194 2195 disable_switch: 2196 gswip_mdio_mask(priv, GSWIP_MDIO_GLOB_ENABLE, 0, GSWIP_MDIO_GLOB); 2197 dsa_unregister_switch(priv->ds); 2198 mdio_bus: 2199 if (mdio_np) { 2200 mdiobus_unregister(priv->ds->slave_mii_bus); 2201 mdiobus_free(priv->ds->slave_mii_bus); 2202 } 2203 put_mdio_node: 2204 of_node_put(mdio_np); 2205 for (i = 0; i < priv->num_gphy_fw; i++) 2206 gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]); 2207 return err; 2208 } 2209 2210 static int gswip_remove(struct platform_device *pdev) 2211 { 2212 struct gswip_priv *priv = platform_get_drvdata(pdev); 2213 int i; 2214 2215 if (!priv) 2216 return 0; 2217 2218 /* disable the switch */ 2219 gswip_mdio_mask(priv, GSWIP_MDIO_GLOB_ENABLE, 0, GSWIP_MDIO_GLOB); 2220 2221 dsa_unregister_switch(priv->ds); 2222 2223 if (priv->ds->slave_mii_bus) { 2224 mdiobus_unregister(priv->ds->slave_mii_bus); 2225 of_node_put(priv->ds->slave_mii_bus->dev.of_node); 2226 mdiobus_free(priv->ds->slave_mii_bus); 2227 } 2228 2229 for (i = 0; i < priv->num_gphy_fw; i++) 2230 gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]); 2231 2232 platform_set_drvdata(pdev, NULL); 2233 2234 return 0; 2235 } 2236 2237 static void gswip_shutdown(struct platform_device *pdev) 2238 { 2239 struct gswip_priv *priv = platform_get_drvdata(pdev); 2240 2241 if (!priv) 2242 return; 2243 2244 dsa_switch_shutdown(priv->ds); 2245 2246 platform_set_drvdata(pdev, NULL); 2247 } 2248 2249 static const struct gswip_hw_info gswip_xrx200 = { 2250 .max_ports = 7, 2251 .cpu_port = 6, 2252 .ops = &gswip_xrx200_switch_ops, 2253 }; 2254 2255 static const struct gswip_hw_info gswip_xrx300 = { 2256 .max_ports = 7, 2257 .cpu_port = 6, 2258 .ops = &gswip_xrx300_switch_ops, 2259 }; 2260 2261 static const struct of_device_id gswip_of_match[] = { 2262 { .compatible = "lantiq,xrx200-gswip", .data = &gswip_xrx200 }, 2263 { .compatible = "lantiq,xrx300-gswip", .data = &gswip_xrx300 }, 2264 { .compatible = "lantiq,xrx330-gswip", .data = &gswip_xrx300 }, 2265 {}, 2266 }; 2267 MODULE_DEVICE_TABLE(of, gswip_of_match); 2268 2269 static struct platform_driver gswip_driver = { 2270 .probe = gswip_probe, 2271 .remove = gswip_remove, 2272 .shutdown = gswip_shutdown, 2273 .driver = { 2274 .name = "gswip", 2275 .of_match_table = gswip_of_match, 2276 }, 2277 }; 2278 2279 module_platform_driver(gswip_driver); 2280 2281 MODULE_FIRMWARE("lantiq/xrx300_phy11g_a21.bin"); 2282 MODULE_FIRMWARE("lantiq/xrx300_phy22f_a21.bin"); 2283 MODULE_FIRMWARE("lantiq/xrx200_phy11g_a14.bin"); 2284 MODULE_FIRMWARE("lantiq/xrx200_phy11g_a22.bin"); 2285 MODULE_FIRMWARE("lantiq/xrx200_phy22f_a14.bin"); 2286 MODULE_FIRMWARE("lantiq/xrx200_phy22f_a22.bin"); 2287 MODULE_AUTHOR("Hauke Mehrtens <hauke@hauke-m.de>"); 2288 MODULE_DESCRIPTION("Lantiq / Intel GSWIP driver"); 2289 MODULE_LICENSE("GPL v2"); 2290