1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Broadcom Starfighter 2 DSA switch driver 4 * 5 * Copyright (C) 2014, Broadcom Corporation 6 */ 7 8 #include <linux/list.h> 9 #include <linux/module.h> 10 #include <linux/netdevice.h> 11 #include <linux/interrupt.h> 12 #include <linux/platform_device.h> 13 #include <linux/phy.h> 14 #include <linux/phy_fixed.h> 15 #include <linux/phylink.h> 16 #include <linux/mii.h> 17 #include <linux/clk.h> 18 #include <linux/of.h> 19 #include <linux/of_irq.h> 20 #include <linux/of_address.h> 21 #include <linux/of_net.h> 22 #include <linux/of_mdio.h> 23 #include <net/dsa.h> 24 #include <linux/ethtool.h> 25 #include <linux/if_bridge.h> 26 #include <linux/brcmphy.h> 27 #include <linux/etherdevice.h> 28 #include <linux/platform_data/b53.h> 29 30 #include "bcm_sf2.h" 31 #include "bcm_sf2_regs.h" 32 #include "b53/b53_priv.h" 33 #include "b53/b53_regs.h" 34 35 static u16 bcm_sf2_reg_rgmii_cntrl(struct bcm_sf2_priv *priv, int port) 36 { 37 switch (priv->type) { 38 case BCM4908_DEVICE_ID: 39 switch (port) { 40 case 7: 41 return REG_RGMII_11_CNTRL; 42 default: 43 break; 44 } 45 break; 46 default: 47 switch (port) { 48 case 0: 49 return REG_RGMII_0_CNTRL; 50 case 1: 51 return REG_RGMII_1_CNTRL; 52 case 2: 53 return REG_RGMII_2_CNTRL; 54 default: 55 break; 56 } 57 } 58 59 WARN_ONCE(1, "Unsupported port %d\n", port); 60 61 /* RO fallback reg */ 62 return REG_SWITCH_STATUS; 63 } 64 65 /* Return the number of active ports, not counting the IMP (CPU) port */ 66 static unsigned int bcm_sf2_num_active_ports(struct dsa_switch *ds) 67 { 68 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 69 unsigned int port, count = 0; 70 71 for (port = 0; port < ds->num_ports; port++) { 72 if (dsa_is_cpu_port(ds, port)) 73 continue; 74 if (priv->port_sts[port].enabled) 75 count++; 76 } 77 78 return count; 79 } 80 81 static void bcm_sf2_recalc_clock(struct dsa_switch *ds) 82 { 83 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 84 unsigned long new_rate; 85 unsigned int ports_active; 86 /* Frequenty in Mhz */ 87 static const unsigned long rate_table[] = { 88 59220000, 89 60820000, 90 62500000, 91 62500000, 92 }; 93 94 ports_active = bcm_sf2_num_active_ports(ds); 95 if (ports_active == 0 || !priv->clk_mdiv) 96 return; 97 98 /* If we overflow our table, just use the recommended operational 99 * frequency 100 */ 101 if (ports_active > ARRAY_SIZE(rate_table)) 102 new_rate = 90000000; 103 else 104 new_rate = rate_table[ports_active - 1]; 105 clk_set_rate(priv->clk_mdiv, new_rate); 106 } 107 108 static void bcm_sf2_imp_setup(struct dsa_switch *ds, int port) 109 { 110 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 111 unsigned int i; 112 u32 reg, offset; 113 114 /* Enable the port memories */ 115 reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL); 116 reg &= ~P_TXQ_PSM_VDD(port); 117 core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL); 118 119 /* Enable forwarding */ 120 core_writel(priv, SW_FWDG_EN, CORE_SWMODE); 121 122 /* Enable IMP port in dumb mode */ 123 reg = core_readl(priv, CORE_SWITCH_CTRL); 124 reg |= MII_DUMB_FWDG_EN; 125 core_writel(priv, reg, CORE_SWITCH_CTRL); 126 127 /* Configure Traffic Class to QoS mapping, allow each priority to map 128 * to a different queue number 129 */ 130 reg = core_readl(priv, CORE_PORT_TC2_QOS_MAP_PORT(port)); 131 for (i = 0; i < SF2_NUM_EGRESS_QUEUES; i++) 132 reg |= i << (PRT_TO_QID_SHIFT * i); 133 core_writel(priv, reg, CORE_PORT_TC2_QOS_MAP_PORT(port)); 134 135 b53_brcm_hdr_setup(ds, port); 136 137 if (port == 8) { 138 if (priv->type == BCM4908_DEVICE_ID || 139 priv->type == BCM7445_DEVICE_ID) 140 offset = CORE_STS_OVERRIDE_IMP; 141 else 142 offset = CORE_STS_OVERRIDE_IMP2; 143 144 /* Force link status for IMP port */ 145 reg = core_readl(priv, offset); 146 reg |= (MII_SW_OR | LINK_STS); 147 if (priv->type == BCM4908_DEVICE_ID) 148 reg |= GMII_SPEED_UP_2G; 149 else 150 reg &= ~GMII_SPEED_UP_2G; 151 core_writel(priv, reg, offset); 152 153 /* Enable Broadcast, Multicast, Unicast forwarding to IMP port */ 154 reg = core_readl(priv, CORE_IMP_CTL); 155 reg |= (RX_BCST_EN | RX_MCST_EN | RX_UCST_EN); 156 reg &= ~(RX_DIS | TX_DIS); 157 core_writel(priv, reg, CORE_IMP_CTL); 158 } else { 159 reg = core_readl(priv, CORE_G_PCTL_PORT(port)); 160 reg &= ~(RX_DIS | TX_DIS); 161 core_writel(priv, reg, CORE_G_PCTL_PORT(port)); 162 } 163 164 priv->port_sts[port].enabled = true; 165 } 166 167 static void bcm_sf2_gphy_enable_set(struct dsa_switch *ds, bool enable) 168 { 169 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 170 u32 reg; 171 172 reg = reg_readl(priv, REG_SPHY_CNTRL); 173 if (enable) { 174 reg |= PHY_RESET; 175 reg &= ~(EXT_PWR_DOWN | IDDQ_BIAS | IDDQ_GLOBAL_PWR | CK25_DIS); 176 reg_writel(priv, reg, REG_SPHY_CNTRL); 177 udelay(21); 178 reg = reg_readl(priv, REG_SPHY_CNTRL); 179 reg &= ~PHY_RESET; 180 } else { 181 reg |= EXT_PWR_DOWN | IDDQ_BIAS | PHY_RESET; 182 reg_writel(priv, reg, REG_SPHY_CNTRL); 183 mdelay(1); 184 reg |= CK25_DIS; 185 } 186 reg_writel(priv, reg, REG_SPHY_CNTRL); 187 188 /* Use PHY-driven LED signaling */ 189 if (!enable) { 190 reg = reg_readl(priv, REG_LED_CNTRL(0)); 191 reg |= SPDLNK_SRC_SEL; 192 reg_writel(priv, reg, REG_LED_CNTRL(0)); 193 } 194 } 195 196 static inline void bcm_sf2_port_intr_enable(struct bcm_sf2_priv *priv, 197 int port) 198 { 199 unsigned int off; 200 201 switch (port) { 202 case 7: 203 off = P7_IRQ_OFF; 204 break; 205 case 0: 206 /* Port 0 interrupts are located on the first bank */ 207 intrl2_0_mask_clear(priv, P_IRQ_MASK(P0_IRQ_OFF)); 208 return; 209 default: 210 off = P_IRQ_OFF(port); 211 break; 212 } 213 214 intrl2_1_mask_clear(priv, P_IRQ_MASK(off)); 215 } 216 217 static inline void bcm_sf2_port_intr_disable(struct bcm_sf2_priv *priv, 218 int port) 219 { 220 unsigned int off; 221 222 switch (port) { 223 case 7: 224 off = P7_IRQ_OFF; 225 break; 226 case 0: 227 /* Port 0 interrupts are located on the first bank */ 228 intrl2_0_mask_set(priv, P_IRQ_MASK(P0_IRQ_OFF)); 229 intrl2_0_writel(priv, P_IRQ_MASK(P0_IRQ_OFF), INTRL2_CPU_CLEAR); 230 return; 231 default: 232 off = P_IRQ_OFF(port); 233 break; 234 } 235 236 intrl2_1_mask_set(priv, P_IRQ_MASK(off)); 237 intrl2_1_writel(priv, P_IRQ_MASK(off), INTRL2_CPU_CLEAR); 238 } 239 240 static int bcm_sf2_port_setup(struct dsa_switch *ds, int port, 241 struct phy_device *phy) 242 { 243 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 244 unsigned int i; 245 u32 reg; 246 247 if (!dsa_is_user_port(ds, port)) 248 return 0; 249 250 priv->port_sts[port].enabled = true; 251 252 bcm_sf2_recalc_clock(ds); 253 254 /* Clear the memory power down */ 255 reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL); 256 reg &= ~P_TXQ_PSM_VDD(port); 257 core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL); 258 259 /* Enable Broadcom tags for that port if requested */ 260 if (priv->brcm_tag_mask & BIT(port)) 261 b53_brcm_hdr_setup(ds, port); 262 263 /* Configure Traffic Class to QoS mapping, allow each priority to map 264 * to a different queue number 265 */ 266 reg = core_readl(priv, CORE_PORT_TC2_QOS_MAP_PORT(port)); 267 for (i = 0; i < SF2_NUM_EGRESS_QUEUES; i++) 268 reg |= i << (PRT_TO_QID_SHIFT * i); 269 core_writel(priv, reg, CORE_PORT_TC2_QOS_MAP_PORT(port)); 270 271 /* Re-enable the GPHY and re-apply workarounds */ 272 if (priv->int_phy_mask & 1 << port && priv->hw_params.num_gphy == 1) { 273 bcm_sf2_gphy_enable_set(ds, true); 274 if (phy) { 275 /* if phy_stop() has been called before, phy 276 * will be in halted state, and phy_start() 277 * will call resume. 278 * 279 * the resume path does not configure back 280 * autoneg settings, and since we hard reset 281 * the phy manually here, we need to reset the 282 * state machine also. 283 */ 284 phy->state = PHY_READY; 285 phy_init_hw(phy); 286 } 287 } 288 289 /* Enable MoCA port interrupts to get notified */ 290 if (port == priv->moca_port) 291 bcm_sf2_port_intr_enable(priv, port); 292 293 /* Set per-queue pause threshold to 32 */ 294 core_writel(priv, 32, CORE_TXQ_THD_PAUSE_QN_PORT(port)); 295 296 /* Set ACB threshold to 24 */ 297 for (i = 0; i < SF2_NUM_EGRESS_QUEUES; i++) { 298 reg = acb_readl(priv, ACB_QUEUE_CFG(port * 299 SF2_NUM_EGRESS_QUEUES + i)); 300 reg &= ~XOFF_THRESHOLD_MASK; 301 reg |= 24; 302 acb_writel(priv, reg, ACB_QUEUE_CFG(port * 303 SF2_NUM_EGRESS_QUEUES + i)); 304 } 305 306 return b53_enable_port(ds, port, phy); 307 } 308 309 static void bcm_sf2_port_disable(struct dsa_switch *ds, int port) 310 { 311 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 312 u32 reg; 313 314 /* Disable learning while in WoL mode */ 315 if (priv->wol_ports_mask & (1 << port)) { 316 reg = core_readl(priv, CORE_DIS_LEARN); 317 reg |= BIT(port); 318 core_writel(priv, reg, CORE_DIS_LEARN); 319 return; 320 } 321 322 if (port == priv->moca_port) 323 bcm_sf2_port_intr_disable(priv, port); 324 325 if (priv->int_phy_mask & 1 << port && priv->hw_params.num_gphy == 1) 326 bcm_sf2_gphy_enable_set(ds, false); 327 328 b53_disable_port(ds, port); 329 330 /* Power down the port memory */ 331 reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL); 332 reg |= P_TXQ_PSM_VDD(port); 333 core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL); 334 335 priv->port_sts[port].enabled = false; 336 337 bcm_sf2_recalc_clock(ds); 338 } 339 340 341 static int bcm_sf2_sw_indir_rw(struct bcm_sf2_priv *priv, int op, int addr, 342 int regnum, u16 val) 343 { 344 int ret = 0; 345 u32 reg; 346 347 reg = reg_readl(priv, REG_SWITCH_CNTRL); 348 reg |= MDIO_MASTER_SEL; 349 reg_writel(priv, reg, REG_SWITCH_CNTRL); 350 351 /* Page << 8 | offset */ 352 reg = 0x70; 353 reg <<= 2; 354 core_writel(priv, addr, reg); 355 356 /* Page << 8 | offset */ 357 reg = 0x80 << 8 | regnum << 1; 358 reg <<= 2; 359 360 if (op) 361 ret = core_readl(priv, reg); 362 else 363 core_writel(priv, val, reg); 364 365 reg = reg_readl(priv, REG_SWITCH_CNTRL); 366 reg &= ~MDIO_MASTER_SEL; 367 reg_writel(priv, reg, REG_SWITCH_CNTRL); 368 369 return ret & 0xffff; 370 } 371 372 static int bcm_sf2_sw_mdio_read(struct mii_bus *bus, int addr, int regnum) 373 { 374 struct bcm_sf2_priv *priv = bus->priv; 375 376 /* Intercept reads from Broadcom pseudo-PHY address, else, send 377 * them to our master MDIO bus controller 378 */ 379 if (addr == BRCM_PSEUDO_PHY_ADDR && priv->indir_phy_mask & BIT(addr)) 380 return bcm_sf2_sw_indir_rw(priv, 1, addr, regnum, 0); 381 else 382 return mdiobus_read_nested(priv->master_mii_bus, addr, regnum); 383 } 384 385 static int bcm_sf2_sw_mdio_write(struct mii_bus *bus, int addr, int regnum, 386 u16 val) 387 { 388 struct bcm_sf2_priv *priv = bus->priv; 389 390 /* Intercept writes to the Broadcom pseudo-PHY address, else, 391 * send them to our master MDIO bus controller 392 */ 393 if (addr == BRCM_PSEUDO_PHY_ADDR && priv->indir_phy_mask & BIT(addr)) 394 return bcm_sf2_sw_indir_rw(priv, 0, addr, regnum, val); 395 else 396 return mdiobus_write_nested(priv->master_mii_bus, addr, 397 regnum, val); 398 } 399 400 static irqreturn_t bcm_sf2_switch_0_isr(int irq, void *dev_id) 401 { 402 struct dsa_switch *ds = dev_id; 403 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 404 405 priv->irq0_stat = intrl2_0_readl(priv, INTRL2_CPU_STATUS) & 406 ~priv->irq0_mask; 407 intrl2_0_writel(priv, priv->irq0_stat, INTRL2_CPU_CLEAR); 408 409 return IRQ_HANDLED; 410 } 411 412 static irqreturn_t bcm_sf2_switch_1_isr(int irq, void *dev_id) 413 { 414 struct dsa_switch *ds = dev_id; 415 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 416 417 priv->irq1_stat = intrl2_1_readl(priv, INTRL2_CPU_STATUS) & 418 ~priv->irq1_mask; 419 intrl2_1_writel(priv, priv->irq1_stat, INTRL2_CPU_CLEAR); 420 421 if (priv->irq1_stat & P_LINK_UP_IRQ(P7_IRQ_OFF)) { 422 priv->port_sts[7].link = true; 423 dsa_port_phylink_mac_change(ds, 7, true); 424 } 425 if (priv->irq1_stat & P_LINK_DOWN_IRQ(P7_IRQ_OFF)) { 426 priv->port_sts[7].link = false; 427 dsa_port_phylink_mac_change(ds, 7, false); 428 } 429 430 return IRQ_HANDLED; 431 } 432 433 static int bcm_sf2_sw_rst(struct bcm_sf2_priv *priv) 434 { 435 unsigned int timeout = 1000; 436 u32 reg; 437 int ret; 438 439 /* The watchdog reset does not work on 7278, we need to hit the 440 * "external" reset line through the reset controller. 441 */ 442 if (priv->type == BCM7278_DEVICE_ID) { 443 ret = reset_control_assert(priv->rcdev); 444 if (ret) 445 return ret; 446 447 return reset_control_deassert(priv->rcdev); 448 } 449 450 reg = core_readl(priv, CORE_WATCHDOG_CTRL); 451 reg |= SOFTWARE_RESET | EN_CHIP_RST | EN_SW_RESET; 452 core_writel(priv, reg, CORE_WATCHDOG_CTRL); 453 454 do { 455 reg = core_readl(priv, CORE_WATCHDOG_CTRL); 456 if (!(reg & SOFTWARE_RESET)) 457 break; 458 459 usleep_range(1000, 2000); 460 } while (timeout-- > 0); 461 462 if (timeout == 0) 463 return -ETIMEDOUT; 464 465 return 0; 466 } 467 468 static void bcm_sf2_crossbar_setup(struct bcm_sf2_priv *priv) 469 { 470 struct device *dev = priv->dev->ds->dev; 471 int shift; 472 u32 mask; 473 u32 reg; 474 int i; 475 476 mask = BIT(priv->num_crossbar_int_ports) - 1; 477 478 reg = reg_readl(priv, REG_CROSSBAR); 479 switch (priv->type) { 480 case BCM4908_DEVICE_ID: 481 shift = CROSSBAR_BCM4908_INT_P7 * priv->num_crossbar_int_ports; 482 reg &= ~(mask << shift); 483 if (0) /* FIXME */ 484 reg |= CROSSBAR_BCM4908_EXT_SERDES << shift; 485 else if (priv->int_phy_mask & BIT(7)) 486 reg |= CROSSBAR_BCM4908_EXT_GPHY4 << shift; 487 else if (phy_interface_mode_is_rgmii(priv->port_sts[7].mode)) 488 reg |= CROSSBAR_BCM4908_EXT_RGMII << shift; 489 else if (WARN(1, "Invalid port mode\n")) 490 return; 491 break; 492 default: 493 return; 494 } 495 reg_writel(priv, reg, REG_CROSSBAR); 496 497 reg = reg_readl(priv, REG_CROSSBAR); 498 for (i = 0; i < priv->num_crossbar_int_ports; i++) { 499 shift = i * priv->num_crossbar_int_ports; 500 501 dev_dbg(dev, "crossbar int port #%d - ext port #%d\n", i, 502 (reg >> shift) & mask); 503 } 504 } 505 506 static void bcm_sf2_intr_disable(struct bcm_sf2_priv *priv) 507 { 508 intrl2_0_mask_set(priv, 0xffffffff); 509 intrl2_0_writel(priv, 0xffffffff, INTRL2_CPU_CLEAR); 510 intrl2_1_mask_set(priv, 0xffffffff); 511 intrl2_1_writel(priv, 0xffffffff, INTRL2_CPU_CLEAR); 512 } 513 514 static void bcm_sf2_identify_ports(struct bcm_sf2_priv *priv, 515 struct device_node *dn) 516 { 517 struct device *dev = priv->dev->ds->dev; 518 struct bcm_sf2_port_status *port_st; 519 struct device_node *port; 520 unsigned int port_num; 521 struct property *prop; 522 int err; 523 524 priv->moca_port = -1; 525 526 for_each_available_child_of_node(dn, port) { 527 if (of_property_read_u32(port, "reg", &port_num)) 528 continue; 529 530 if (port_num >= DSA_MAX_PORTS) { 531 dev_err(dev, "Invalid port number %d\n", port_num); 532 continue; 533 } 534 535 port_st = &priv->port_sts[port_num]; 536 537 /* Internal PHYs get assigned a specific 'phy-mode' property 538 * value: "internal" to help flag them before MDIO probing 539 * has completed, since they might be turned off at that 540 * time 541 */ 542 err = of_get_phy_mode(port, &port_st->mode); 543 if (err) 544 continue; 545 546 if (port_st->mode == PHY_INTERFACE_MODE_INTERNAL) 547 priv->int_phy_mask |= 1 << port_num; 548 549 if (port_st->mode == PHY_INTERFACE_MODE_MOCA) 550 priv->moca_port = port_num; 551 552 if (of_property_read_bool(port, "brcm,use-bcm-hdr")) 553 priv->brcm_tag_mask |= 1 << port_num; 554 555 /* Ensure that port 5 is not picked up as a DSA CPU port 556 * flavour but a regular port instead. We should be using 557 * devlink to be able to set the port flavour. 558 */ 559 if (port_num == 5 && priv->type == BCM7278_DEVICE_ID) { 560 prop = of_find_property(port, "ethernet", NULL); 561 if (prop) 562 of_remove_property(port, prop); 563 } 564 } 565 } 566 567 static int bcm_sf2_mdio_register(struct dsa_switch *ds) 568 { 569 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 570 struct device_node *dn, *child; 571 struct phy_device *phydev; 572 struct property *prop; 573 static int index; 574 int err, reg; 575 576 /* Find our integrated MDIO bus node */ 577 dn = of_find_compatible_node(NULL, NULL, "brcm,unimac-mdio"); 578 priv->master_mii_bus = of_mdio_find_bus(dn); 579 if (!priv->master_mii_bus) { 580 of_node_put(dn); 581 return -EPROBE_DEFER; 582 } 583 584 get_device(&priv->master_mii_bus->dev); 585 priv->master_mii_dn = dn; 586 587 priv->slave_mii_bus = devm_mdiobus_alloc(ds->dev); 588 if (!priv->slave_mii_bus) { 589 of_node_put(dn); 590 return -ENOMEM; 591 } 592 593 priv->slave_mii_bus->priv = priv; 594 priv->slave_mii_bus->name = "sf2 slave mii"; 595 priv->slave_mii_bus->read = bcm_sf2_sw_mdio_read; 596 priv->slave_mii_bus->write = bcm_sf2_sw_mdio_write; 597 snprintf(priv->slave_mii_bus->id, MII_BUS_ID_SIZE, "sf2-%d", 598 index++); 599 priv->slave_mii_bus->dev.of_node = dn; 600 601 /* Include the pseudo-PHY address to divert reads towards our 602 * workaround. This is only required for 7445D0, since 7445E0 603 * disconnects the internal switch pseudo-PHY such that we can use the 604 * regular SWITCH_MDIO master controller instead. 605 * 606 * Here we flag the pseudo PHY as needing special treatment and would 607 * otherwise make all other PHY read/writes go to the master MDIO bus 608 * controller that comes with this switch backed by the "mdio-unimac" 609 * driver. 610 */ 611 if (of_machine_is_compatible("brcm,bcm7445d0")) 612 priv->indir_phy_mask |= (1 << BRCM_PSEUDO_PHY_ADDR) | (1 << 0); 613 else 614 priv->indir_phy_mask = 0; 615 616 ds->phys_mii_mask = priv->indir_phy_mask; 617 ds->slave_mii_bus = priv->slave_mii_bus; 618 priv->slave_mii_bus->parent = ds->dev->parent; 619 priv->slave_mii_bus->phy_mask = ~priv->indir_phy_mask; 620 621 /* We need to make sure that of_phy_connect() will not work by 622 * removing the 'phandle' and 'linux,phandle' properties and 623 * unregister the existing PHY device that was already registered. 624 */ 625 for_each_available_child_of_node(dn, child) { 626 if (of_property_read_u32(child, "reg", ®) || 627 reg >= PHY_MAX_ADDR) 628 continue; 629 630 if (!(priv->indir_phy_mask & BIT(reg))) 631 continue; 632 633 prop = of_find_property(child, "phandle", NULL); 634 if (prop) 635 of_remove_property(child, prop); 636 637 prop = of_find_property(child, "linux,phandle", NULL); 638 if (prop) 639 of_remove_property(child, prop); 640 641 phydev = of_phy_find_device(child); 642 if (phydev) 643 phy_device_remove(phydev); 644 } 645 646 err = mdiobus_register(priv->slave_mii_bus); 647 if (err && dn) 648 of_node_put(dn); 649 650 return err; 651 } 652 653 static void bcm_sf2_mdio_unregister(struct bcm_sf2_priv *priv) 654 { 655 mdiobus_unregister(priv->slave_mii_bus); 656 of_node_put(priv->master_mii_dn); 657 } 658 659 static u32 bcm_sf2_sw_get_phy_flags(struct dsa_switch *ds, int port) 660 { 661 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 662 663 /* The BCM7xxx PHY driver expects to find the integrated PHY revision 664 * in bits 15:8 and the patch level in bits 7:0 which is exactly what 665 * the REG_PHY_REVISION register layout is. 666 */ 667 if (priv->int_phy_mask & BIT(port)) 668 return priv->hw_params.gphy_rev; 669 else 670 return PHY_BRCM_AUTO_PWRDWN_ENABLE | 671 PHY_BRCM_DIS_TXCRXC_NOENRGY | 672 PHY_BRCM_IDDQ_SUSPEND; 673 } 674 675 static void bcm_sf2_sw_validate(struct dsa_switch *ds, int port, 676 unsigned long *supported, 677 struct phylink_link_state *state) 678 { 679 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 680 __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, }; 681 682 if (!phy_interface_mode_is_rgmii(state->interface) && 683 state->interface != PHY_INTERFACE_MODE_MII && 684 state->interface != PHY_INTERFACE_MODE_REVMII && 685 state->interface != PHY_INTERFACE_MODE_GMII && 686 state->interface != PHY_INTERFACE_MODE_INTERNAL && 687 state->interface != PHY_INTERFACE_MODE_MOCA) { 688 linkmode_zero(supported); 689 if (port != core_readl(priv, CORE_IMP0_PRT_ID)) 690 dev_err(ds->dev, 691 "Unsupported interface: %d for port %d\n", 692 state->interface, port); 693 return; 694 } 695 696 /* Allow all the expected bits */ 697 phylink_set(mask, Autoneg); 698 phylink_set_port_modes(mask); 699 phylink_set(mask, Pause); 700 phylink_set(mask, Asym_Pause); 701 702 /* With the exclusion of MII and Reverse MII, we support Gigabit, 703 * including Half duplex 704 */ 705 if (state->interface != PHY_INTERFACE_MODE_MII && 706 state->interface != PHY_INTERFACE_MODE_REVMII) { 707 phylink_set(mask, 1000baseT_Full); 708 phylink_set(mask, 1000baseT_Half); 709 } 710 711 phylink_set(mask, 10baseT_Half); 712 phylink_set(mask, 10baseT_Full); 713 phylink_set(mask, 100baseT_Half); 714 phylink_set(mask, 100baseT_Full); 715 716 linkmode_and(supported, supported, mask); 717 linkmode_and(state->advertising, state->advertising, mask); 718 } 719 720 static void bcm_sf2_sw_mac_config(struct dsa_switch *ds, int port, 721 unsigned int mode, 722 const struct phylink_link_state *state) 723 { 724 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 725 u32 id_mode_dis = 0, port_mode; 726 u32 reg_rgmii_ctrl; 727 u32 reg; 728 729 if (port == core_readl(priv, CORE_IMP0_PRT_ID)) 730 return; 731 732 switch (state->interface) { 733 case PHY_INTERFACE_MODE_RGMII: 734 id_mode_dis = 1; 735 fallthrough; 736 case PHY_INTERFACE_MODE_RGMII_TXID: 737 port_mode = EXT_GPHY; 738 break; 739 case PHY_INTERFACE_MODE_MII: 740 port_mode = EXT_EPHY; 741 break; 742 case PHY_INTERFACE_MODE_REVMII: 743 port_mode = EXT_REVMII; 744 break; 745 default: 746 /* Nothing required for all other PHYs: internal and MoCA */ 747 return; 748 } 749 750 reg_rgmii_ctrl = bcm_sf2_reg_rgmii_cntrl(priv, port); 751 752 /* Clear id_mode_dis bit, and the existing port mode, let 753 * RGMII_MODE_EN bet set by mac_link_{up,down} 754 */ 755 reg = reg_readl(priv, reg_rgmii_ctrl); 756 reg &= ~ID_MODE_DIS; 757 reg &= ~(PORT_MODE_MASK << PORT_MODE_SHIFT); 758 759 reg |= port_mode; 760 if (id_mode_dis) 761 reg |= ID_MODE_DIS; 762 763 reg_writel(priv, reg, reg_rgmii_ctrl); 764 } 765 766 static void bcm_sf2_sw_mac_link_set(struct dsa_switch *ds, int port, 767 phy_interface_t interface, bool link) 768 { 769 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 770 u32 reg_rgmii_ctrl; 771 u32 reg; 772 773 if (!phy_interface_mode_is_rgmii(interface) && 774 interface != PHY_INTERFACE_MODE_MII && 775 interface != PHY_INTERFACE_MODE_REVMII) 776 return; 777 778 reg_rgmii_ctrl = bcm_sf2_reg_rgmii_cntrl(priv, port); 779 780 /* If the link is down, just disable the interface to conserve power */ 781 reg = reg_readl(priv, reg_rgmii_ctrl); 782 if (link) 783 reg |= RGMII_MODE_EN; 784 else 785 reg &= ~RGMII_MODE_EN; 786 reg_writel(priv, reg, reg_rgmii_ctrl); 787 } 788 789 static void bcm_sf2_sw_mac_link_down(struct dsa_switch *ds, int port, 790 unsigned int mode, 791 phy_interface_t interface) 792 { 793 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 794 u32 reg, offset; 795 796 if (port != core_readl(priv, CORE_IMP0_PRT_ID)) { 797 if (priv->type == BCM4908_DEVICE_ID || 798 priv->type == BCM7445_DEVICE_ID) 799 offset = CORE_STS_OVERRIDE_GMIIP_PORT(port); 800 else 801 offset = CORE_STS_OVERRIDE_GMIIP2_PORT(port); 802 803 reg = core_readl(priv, offset); 804 reg &= ~LINK_STS; 805 core_writel(priv, reg, offset); 806 } 807 808 bcm_sf2_sw_mac_link_set(ds, port, interface, false); 809 } 810 811 static void bcm_sf2_sw_mac_link_up(struct dsa_switch *ds, int port, 812 unsigned int mode, 813 phy_interface_t interface, 814 struct phy_device *phydev, 815 int speed, int duplex, 816 bool tx_pause, bool rx_pause) 817 { 818 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 819 struct ethtool_eee *p = &priv->dev->ports[port].eee; 820 821 bcm_sf2_sw_mac_link_set(ds, port, interface, true); 822 823 if (port != core_readl(priv, CORE_IMP0_PRT_ID)) { 824 u32 reg_rgmii_ctrl = 0; 825 u32 reg, offset; 826 827 if (priv->type == BCM4908_DEVICE_ID || 828 priv->type == BCM7445_DEVICE_ID) 829 offset = CORE_STS_OVERRIDE_GMIIP_PORT(port); 830 else 831 offset = CORE_STS_OVERRIDE_GMIIP2_PORT(port); 832 833 if (interface == PHY_INTERFACE_MODE_RGMII || 834 interface == PHY_INTERFACE_MODE_RGMII_TXID || 835 interface == PHY_INTERFACE_MODE_MII || 836 interface == PHY_INTERFACE_MODE_REVMII) { 837 reg_rgmii_ctrl = bcm_sf2_reg_rgmii_cntrl(priv, port); 838 reg = reg_readl(priv, reg_rgmii_ctrl); 839 reg &= ~(RX_PAUSE_EN | TX_PAUSE_EN); 840 841 if (tx_pause) 842 reg |= TX_PAUSE_EN; 843 if (rx_pause) 844 reg |= RX_PAUSE_EN; 845 846 reg_writel(priv, reg, reg_rgmii_ctrl); 847 } 848 849 reg = SW_OVERRIDE | LINK_STS; 850 switch (speed) { 851 case SPEED_1000: 852 reg |= SPDSTS_1000 << SPEED_SHIFT; 853 break; 854 case SPEED_100: 855 reg |= SPDSTS_100 << SPEED_SHIFT; 856 break; 857 } 858 859 if (duplex == DUPLEX_FULL) 860 reg |= DUPLX_MODE; 861 862 core_writel(priv, reg, offset); 863 } 864 865 if (mode == MLO_AN_PHY && phydev) 866 p->eee_enabled = b53_eee_init(ds, port, phydev); 867 } 868 869 static void bcm_sf2_sw_fixed_state(struct dsa_switch *ds, int port, 870 struct phylink_link_state *status) 871 { 872 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 873 874 status->link = false; 875 876 /* MoCA port is special as we do not get link status from CORE_LNKSTS, 877 * which means that we need to force the link at the port override 878 * level to get the data to flow. We do use what the interrupt handler 879 * did determine before. 880 * 881 * For the other ports, we just force the link status, since this is 882 * a fixed PHY device. 883 */ 884 if (port == priv->moca_port) { 885 status->link = priv->port_sts[port].link; 886 /* For MoCA interfaces, also force a link down notification 887 * since some version of the user-space daemon (mocad) use 888 * cmd->autoneg to force the link, which messes up the PHY 889 * state machine and make it go in PHY_FORCING state instead. 890 */ 891 if (!status->link) 892 netif_carrier_off(dsa_to_port(ds, port)->slave); 893 status->duplex = DUPLEX_FULL; 894 } else { 895 status->link = true; 896 } 897 } 898 899 static void bcm_sf2_enable_acb(struct dsa_switch *ds) 900 { 901 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 902 u32 reg; 903 904 /* Enable ACB globally */ 905 reg = acb_readl(priv, ACB_CONTROL); 906 reg |= (ACB_FLUSH_MASK << ACB_FLUSH_SHIFT); 907 acb_writel(priv, reg, ACB_CONTROL); 908 reg &= ~(ACB_FLUSH_MASK << ACB_FLUSH_SHIFT); 909 reg |= ACB_EN | ACB_ALGORITHM; 910 acb_writel(priv, reg, ACB_CONTROL); 911 } 912 913 static int bcm_sf2_sw_suspend(struct dsa_switch *ds) 914 { 915 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 916 unsigned int port; 917 918 bcm_sf2_intr_disable(priv); 919 920 /* Disable all ports physically present including the IMP 921 * port, the other ones have already been disabled during 922 * bcm_sf2_sw_setup 923 */ 924 for (port = 0; port < ds->num_ports; port++) { 925 if (dsa_is_user_port(ds, port) || dsa_is_cpu_port(ds, port)) 926 bcm_sf2_port_disable(ds, port); 927 } 928 929 if (!priv->wol_ports_mask) 930 clk_disable_unprepare(priv->clk); 931 932 return 0; 933 } 934 935 static int bcm_sf2_sw_resume(struct dsa_switch *ds) 936 { 937 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 938 int ret; 939 940 if (!priv->wol_ports_mask) 941 clk_prepare_enable(priv->clk); 942 943 ret = bcm_sf2_sw_rst(priv); 944 if (ret) { 945 pr_err("%s: failed to software reset switch\n", __func__); 946 return ret; 947 } 948 949 bcm_sf2_crossbar_setup(priv); 950 951 ret = bcm_sf2_cfp_resume(ds); 952 if (ret) 953 return ret; 954 955 if (priv->hw_params.num_gphy == 1) 956 bcm_sf2_gphy_enable_set(ds, true); 957 958 ds->ops->setup(ds); 959 960 return 0; 961 } 962 963 static void bcm_sf2_sw_get_wol(struct dsa_switch *ds, int port, 964 struct ethtool_wolinfo *wol) 965 { 966 struct net_device *p = dsa_to_port(ds, port)->cpu_dp->master; 967 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 968 struct ethtool_wolinfo pwol = { }; 969 970 /* Get the parent device WoL settings */ 971 if (p->ethtool_ops->get_wol) 972 p->ethtool_ops->get_wol(p, &pwol); 973 974 /* Advertise the parent device supported settings */ 975 wol->supported = pwol.supported; 976 memset(&wol->sopass, 0, sizeof(wol->sopass)); 977 978 if (pwol.wolopts & WAKE_MAGICSECURE) 979 memcpy(&wol->sopass, pwol.sopass, sizeof(wol->sopass)); 980 981 if (priv->wol_ports_mask & (1 << port)) 982 wol->wolopts = pwol.wolopts; 983 else 984 wol->wolopts = 0; 985 } 986 987 static int bcm_sf2_sw_set_wol(struct dsa_switch *ds, int port, 988 struct ethtool_wolinfo *wol) 989 { 990 struct net_device *p = dsa_to_port(ds, port)->cpu_dp->master; 991 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 992 s8 cpu_port = dsa_to_port(ds, port)->cpu_dp->index; 993 struct ethtool_wolinfo pwol = { }; 994 995 if (p->ethtool_ops->get_wol) 996 p->ethtool_ops->get_wol(p, &pwol); 997 if (wol->wolopts & ~pwol.supported) 998 return -EINVAL; 999 1000 if (wol->wolopts) 1001 priv->wol_ports_mask |= (1 << port); 1002 else 1003 priv->wol_ports_mask &= ~(1 << port); 1004 1005 /* If we have at least one port enabled, make sure the CPU port 1006 * is also enabled. If the CPU port is the last one enabled, we disable 1007 * it since this configuration does not make sense. 1008 */ 1009 if (priv->wol_ports_mask && priv->wol_ports_mask != (1 << cpu_port)) 1010 priv->wol_ports_mask |= (1 << cpu_port); 1011 else 1012 priv->wol_ports_mask &= ~(1 << cpu_port); 1013 1014 return p->ethtool_ops->set_wol(p, wol); 1015 } 1016 1017 static int bcm_sf2_sw_setup(struct dsa_switch *ds) 1018 { 1019 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 1020 unsigned int port; 1021 1022 /* Enable all valid ports and disable those unused */ 1023 for (port = 0; port < priv->hw_params.num_ports; port++) { 1024 /* IMP port receives special treatment */ 1025 if (dsa_is_user_port(ds, port)) 1026 bcm_sf2_port_setup(ds, port, NULL); 1027 else if (dsa_is_cpu_port(ds, port)) 1028 bcm_sf2_imp_setup(ds, port); 1029 else 1030 bcm_sf2_port_disable(ds, port); 1031 } 1032 1033 b53_configure_vlan(ds); 1034 bcm_sf2_enable_acb(ds); 1035 1036 return b53_setup_devlink_resources(ds); 1037 } 1038 1039 static void bcm_sf2_sw_teardown(struct dsa_switch *ds) 1040 { 1041 dsa_devlink_resources_unregister(ds); 1042 } 1043 1044 /* The SWITCH_CORE register space is managed by b53 but operates on a page + 1045 * register basis so we need to translate that into an address that the 1046 * bus-glue understands. 1047 */ 1048 #define SF2_PAGE_REG_MKADDR(page, reg) ((page) << 10 | (reg) << 2) 1049 1050 static int bcm_sf2_core_read8(struct b53_device *dev, u8 page, u8 reg, 1051 u8 *val) 1052 { 1053 struct bcm_sf2_priv *priv = dev->priv; 1054 1055 *val = core_readl(priv, SF2_PAGE_REG_MKADDR(page, reg)); 1056 1057 return 0; 1058 } 1059 1060 static int bcm_sf2_core_read16(struct b53_device *dev, u8 page, u8 reg, 1061 u16 *val) 1062 { 1063 struct bcm_sf2_priv *priv = dev->priv; 1064 1065 *val = core_readl(priv, SF2_PAGE_REG_MKADDR(page, reg)); 1066 1067 return 0; 1068 } 1069 1070 static int bcm_sf2_core_read32(struct b53_device *dev, u8 page, u8 reg, 1071 u32 *val) 1072 { 1073 struct bcm_sf2_priv *priv = dev->priv; 1074 1075 *val = core_readl(priv, SF2_PAGE_REG_MKADDR(page, reg)); 1076 1077 return 0; 1078 } 1079 1080 static int bcm_sf2_core_read64(struct b53_device *dev, u8 page, u8 reg, 1081 u64 *val) 1082 { 1083 struct bcm_sf2_priv *priv = dev->priv; 1084 1085 *val = core_readq(priv, SF2_PAGE_REG_MKADDR(page, reg)); 1086 1087 return 0; 1088 } 1089 1090 static int bcm_sf2_core_write8(struct b53_device *dev, u8 page, u8 reg, 1091 u8 value) 1092 { 1093 struct bcm_sf2_priv *priv = dev->priv; 1094 1095 core_writel(priv, value, SF2_PAGE_REG_MKADDR(page, reg)); 1096 1097 return 0; 1098 } 1099 1100 static int bcm_sf2_core_write16(struct b53_device *dev, u8 page, u8 reg, 1101 u16 value) 1102 { 1103 struct bcm_sf2_priv *priv = dev->priv; 1104 1105 core_writel(priv, value, SF2_PAGE_REG_MKADDR(page, reg)); 1106 1107 return 0; 1108 } 1109 1110 static int bcm_sf2_core_write32(struct b53_device *dev, u8 page, u8 reg, 1111 u32 value) 1112 { 1113 struct bcm_sf2_priv *priv = dev->priv; 1114 1115 core_writel(priv, value, SF2_PAGE_REG_MKADDR(page, reg)); 1116 1117 return 0; 1118 } 1119 1120 static int bcm_sf2_core_write64(struct b53_device *dev, u8 page, u8 reg, 1121 u64 value) 1122 { 1123 struct bcm_sf2_priv *priv = dev->priv; 1124 1125 core_writeq(priv, value, SF2_PAGE_REG_MKADDR(page, reg)); 1126 1127 return 0; 1128 } 1129 1130 static const struct b53_io_ops bcm_sf2_io_ops = { 1131 .read8 = bcm_sf2_core_read8, 1132 .read16 = bcm_sf2_core_read16, 1133 .read32 = bcm_sf2_core_read32, 1134 .read48 = bcm_sf2_core_read64, 1135 .read64 = bcm_sf2_core_read64, 1136 .write8 = bcm_sf2_core_write8, 1137 .write16 = bcm_sf2_core_write16, 1138 .write32 = bcm_sf2_core_write32, 1139 .write48 = bcm_sf2_core_write64, 1140 .write64 = bcm_sf2_core_write64, 1141 }; 1142 1143 static void bcm_sf2_sw_get_strings(struct dsa_switch *ds, int port, 1144 u32 stringset, uint8_t *data) 1145 { 1146 int cnt = b53_get_sset_count(ds, port, stringset); 1147 1148 b53_get_strings(ds, port, stringset, data); 1149 bcm_sf2_cfp_get_strings(ds, port, stringset, 1150 data + cnt * ETH_GSTRING_LEN); 1151 } 1152 1153 static void bcm_sf2_sw_get_ethtool_stats(struct dsa_switch *ds, int port, 1154 uint64_t *data) 1155 { 1156 int cnt = b53_get_sset_count(ds, port, ETH_SS_STATS); 1157 1158 b53_get_ethtool_stats(ds, port, data); 1159 bcm_sf2_cfp_get_ethtool_stats(ds, port, data + cnt); 1160 } 1161 1162 static int bcm_sf2_sw_get_sset_count(struct dsa_switch *ds, int port, 1163 int sset) 1164 { 1165 int cnt = b53_get_sset_count(ds, port, sset); 1166 1167 if (cnt < 0) 1168 return cnt; 1169 1170 cnt += bcm_sf2_cfp_get_sset_count(ds, port, sset); 1171 1172 return cnt; 1173 } 1174 1175 static const struct dsa_switch_ops bcm_sf2_ops = { 1176 .get_tag_protocol = b53_get_tag_protocol, 1177 .setup = bcm_sf2_sw_setup, 1178 .teardown = bcm_sf2_sw_teardown, 1179 .get_strings = bcm_sf2_sw_get_strings, 1180 .get_ethtool_stats = bcm_sf2_sw_get_ethtool_stats, 1181 .get_sset_count = bcm_sf2_sw_get_sset_count, 1182 .get_ethtool_phy_stats = b53_get_ethtool_phy_stats, 1183 .get_phy_flags = bcm_sf2_sw_get_phy_flags, 1184 .phylink_validate = bcm_sf2_sw_validate, 1185 .phylink_mac_config = bcm_sf2_sw_mac_config, 1186 .phylink_mac_link_down = bcm_sf2_sw_mac_link_down, 1187 .phylink_mac_link_up = bcm_sf2_sw_mac_link_up, 1188 .phylink_fixed_state = bcm_sf2_sw_fixed_state, 1189 .suspend = bcm_sf2_sw_suspend, 1190 .resume = bcm_sf2_sw_resume, 1191 .get_wol = bcm_sf2_sw_get_wol, 1192 .set_wol = bcm_sf2_sw_set_wol, 1193 .port_enable = bcm_sf2_port_setup, 1194 .port_disable = bcm_sf2_port_disable, 1195 .get_mac_eee = b53_get_mac_eee, 1196 .set_mac_eee = b53_set_mac_eee, 1197 .port_bridge_join = b53_br_join, 1198 .port_bridge_leave = b53_br_leave, 1199 .port_pre_bridge_flags = b53_br_flags_pre, 1200 .port_bridge_flags = b53_br_flags, 1201 .port_stp_state_set = b53_br_set_stp_state, 1202 .port_fast_age = b53_br_fast_age, 1203 .port_vlan_filtering = b53_vlan_filtering, 1204 .port_vlan_add = b53_vlan_add, 1205 .port_vlan_del = b53_vlan_del, 1206 .port_fdb_dump = b53_fdb_dump, 1207 .port_fdb_add = b53_fdb_add, 1208 .port_fdb_del = b53_fdb_del, 1209 .get_rxnfc = bcm_sf2_get_rxnfc, 1210 .set_rxnfc = bcm_sf2_set_rxnfc, 1211 .port_mirror_add = b53_mirror_add, 1212 .port_mirror_del = b53_mirror_del, 1213 .port_mdb_add = b53_mdb_add, 1214 .port_mdb_del = b53_mdb_del, 1215 }; 1216 1217 struct bcm_sf2_of_data { 1218 u32 type; 1219 const u16 *reg_offsets; 1220 unsigned int core_reg_align; 1221 unsigned int num_cfp_rules; 1222 unsigned int num_crossbar_int_ports; 1223 }; 1224 1225 static const u16 bcm_sf2_4908_reg_offsets[] = { 1226 [REG_SWITCH_CNTRL] = 0x00, 1227 [REG_SWITCH_STATUS] = 0x04, 1228 [REG_DIR_DATA_WRITE] = 0x08, 1229 [REG_DIR_DATA_READ] = 0x0c, 1230 [REG_SWITCH_REVISION] = 0x10, 1231 [REG_PHY_REVISION] = 0x14, 1232 [REG_SPHY_CNTRL] = 0x24, 1233 [REG_CROSSBAR] = 0xc8, 1234 [REG_RGMII_11_CNTRL] = 0x014c, 1235 [REG_LED_0_CNTRL] = 0x40, 1236 [REG_LED_1_CNTRL] = 0x4c, 1237 [REG_LED_2_CNTRL] = 0x58, 1238 }; 1239 1240 static const struct bcm_sf2_of_data bcm_sf2_4908_data = { 1241 .type = BCM4908_DEVICE_ID, 1242 .core_reg_align = 0, 1243 .reg_offsets = bcm_sf2_4908_reg_offsets, 1244 .num_cfp_rules = 256, 1245 .num_crossbar_int_ports = 2, 1246 }; 1247 1248 /* Register offsets for the SWITCH_REG_* block */ 1249 static const u16 bcm_sf2_7445_reg_offsets[] = { 1250 [REG_SWITCH_CNTRL] = 0x00, 1251 [REG_SWITCH_STATUS] = 0x04, 1252 [REG_DIR_DATA_WRITE] = 0x08, 1253 [REG_DIR_DATA_READ] = 0x0C, 1254 [REG_SWITCH_REVISION] = 0x18, 1255 [REG_PHY_REVISION] = 0x1C, 1256 [REG_SPHY_CNTRL] = 0x2C, 1257 [REG_RGMII_0_CNTRL] = 0x34, 1258 [REG_RGMII_1_CNTRL] = 0x40, 1259 [REG_RGMII_2_CNTRL] = 0x4c, 1260 [REG_LED_0_CNTRL] = 0x90, 1261 [REG_LED_1_CNTRL] = 0x94, 1262 [REG_LED_2_CNTRL] = 0x98, 1263 }; 1264 1265 static const struct bcm_sf2_of_data bcm_sf2_7445_data = { 1266 .type = BCM7445_DEVICE_ID, 1267 .core_reg_align = 0, 1268 .reg_offsets = bcm_sf2_7445_reg_offsets, 1269 .num_cfp_rules = 256, 1270 }; 1271 1272 static const u16 bcm_sf2_7278_reg_offsets[] = { 1273 [REG_SWITCH_CNTRL] = 0x00, 1274 [REG_SWITCH_STATUS] = 0x04, 1275 [REG_DIR_DATA_WRITE] = 0x08, 1276 [REG_DIR_DATA_READ] = 0x0c, 1277 [REG_SWITCH_REVISION] = 0x10, 1278 [REG_PHY_REVISION] = 0x14, 1279 [REG_SPHY_CNTRL] = 0x24, 1280 [REG_RGMII_0_CNTRL] = 0xe0, 1281 [REG_RGMII_1_CNTRL] = 0xec, 1282 [REG_RGMII_2_CNTRL] = 0xf8, 1283 [REG_LED_0_CNTRL] = 0x40, 1284 [REG_LED_1_CNTRL] = 0x4c, 1285 [REG_LED_2_CNTRL] = 0x58, 1286 }; 1287 1288 static const struct bcm_sf2_of_data bcm_sf2_7278_data = { 1289 .type = BCM7278_DEVICE_ID, 1290 .core_reg_align = 1, 1291 .reg_offsets = bcm_sf2_7278_reg_offsets, 1292 .num_cfp_rules = 128, 1293 }; 1294 1295 static const struct of_device_id bcm_sf2_of_match[] = { 1296 { .compatible = "brcm,bcm4908-switch", 1297 .data = &bcm_sf2_4908_data 1298 }, 1299 { .compatible = "brcm,bcm7445-switch-v4.0", 1300 .data = &bcm_sf2_7445_data 1301 }, 1302 { .compatible = "brcm,bcm7278-switch-v4.0", 1303 .data = &bcm_sf2_7278_data 1304 }, 1305 { .compatible = "brcm,bcm7278-switch-v4.8", 1306 .data = &bcm_sf2_7278_data 1307 }, 1308 { /* sentinel */ }, 1309 }; 1310 MODULE_DEVICE_TABLE(of, bcm_sf2_of_match); 1311 1312 static int bcm_sf2_sw_probe(struct platform_device *pdev) 1313 { 1314 const char *reg_names[BCM_SF2_REGS_NUM] = BCM_SF2_REGS_NAME; 1315 struct device_node *dn = pdev->dev.of_node; 1316 const struct of_device_id *of_id = NULL; 1317 const struct bcm_sf2_of_data *data; 1318 struct b53_platform_data *pdata; 1319 struct dsa_switch_ops *ops; 1320 struct device_node *ports; 1321 struct bcm_sf2_priv *priv; 1322 struct b53_device *dev; 1323 struct dsa_switch *ds; 1324 void __iomem **base; 1325 unsigned int i; 1326 u32 reg, rev; 1327 int ret; 1328 1329 priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); 1330 if (!priv) 1331 return -ENOMEM; 1332 1333 ops = devm_kzalloc(&pdev->dev, sizeof(*ops), GFP_KERNEL); 1334 if (!ops) 1335 return -ENOMEM; 1336 1337 dev = b53_switch_alloc(&pdev->dev, &bcm_sf2_io_ops, priv); 1338 if (!dev) 1339 return -ENOMEM; 1340 1341 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); 1342 if (!pdata) 1343 return -ENOMEM; 1344 1345 of_id = of_match_node(bcm_sf2_of_match, dn); 1346 if (!of_id || !of_id->data) 1347 return -EINVAL; 1348 1349 data = of_id->data; 1350 1351 /* Set SWITCH_REG register offsets and SWITCH_CORE align factor */ 1352 priv->type = data->type; 1353 priv->reg_offsets = data->reg_offsets; 1354 priv->core_reg_align = data->core_reg_align; 1355 priv->num_cfp_rules = data->num_cfp_rules; 1356 priv->num_crossbar_int_ports = data->num_crossbar_int_ports; 1357 1358 priv->rcdev = devm_reset_control_get_optional_exclusive(&pdev->dev, 1359 "switch"); 1360 if (IS_ERR(priv->rcdev)) 1361 return PTR_ERR(priv->rcdev); 1362 1363 /* Auto-detection using standard registers will not work, so 1364 * provide an indication of what kind of device we are for 1365 * b53_common to work with 1366 */ 1367 pdata->chip_id = priv->type; 1368 dev->pdata = pdata; 1369 1370 priv->dev = dev; 1371 ds = dev->ds; 1372 ds->ops = &bcm_sf2_ops; 1373 1374 /* Advertise the 8 egress queues */ 1375 ds->num_tx_queues = SF2_NUM_EGRESS_QUEUES; 1376 1377 dev_set_drvdata(&pdev->dev, priv); 1378 1379 spin_lock_init(&priv->indir_lock); 1380 mutex_init(&priv->cfp.lock); 1381 INIT_LIST_HEAD(&priv->cfp.rules_list); 1382 1383 /* CFP rule #0 cannot be used for specific classifications, flag it as 1384 * permanently used 1385 */ 1386 set_bit(0, priv->cfp.used); 1387 set_bit(0, priv->cfp.unique); 1388 1389 /* Balance of_node_put() done by of_find_node_by_name() */ 1390 of_node_get(dn); 1391 ports = of_find_node_by_name(dn, "ports"); 1392 if (ports) { 1393 bcm_sf2_identify_ports(priv, ports); 1394 of_node_put(ports); 1395 } 1396 1397 priv->irq0 = irq_of_parse_and_map(dn, 0); 1398 priv->irq1 = irq_of_parse_and_map(dn, 1); 1399 1400 base = &priv->core; 1401 for (i = 0; i < BCM_SF2_REGS_NUM; i++) { 1402 *base = devm_platform_ioremap_resource(pdev, i); 1403 if (IS_ERR(*base)) { 1404 pr_err("unable to find register: %s\n", reg_names[i]); 1405 return PTR_ERR(*base); 1406 } 1407 base++; 1408 } 1409 1410 priv->clk = devm_clk_get_optional(&pdev->dev, "sw_switch"); 1411 if (IS_ERR(priv->clk)) 1412 return PTR_ERR(priv->clk); 1413 1414 clk_prepare_enable(priv->clk); 1415 1416 priv->clk_mdiv = devm_clk_get_optional(&pdev->dev, "sw_switch_mdiv"); 1417 if (IS_ERR(priv->clk_mdiv)) { 1418 ret = PTR_ERR(priv->clk_mdiv); 1419 goto out_clk; 1420 } 1421 1422 clk_prepare_enable(priv->clk_mdiv); 1423 1424 ret = bcm_sf2_sw_rst(priv); 1425 if (ret) { 1426 pr_err("unable to software reset switch: %d\n", ret); 1427 goto out_clk_mdiv; 1428 } 1429 1430 bcm_sf2_crossbar_setup(priv); 1431 1432 bcm_sf2_gphy_enable_set(priv->dev->ds, true); 1433 1434 ret = bcm_sf2_mdio_register(ds); 1435 if (ret) { 1436 pr_err("failed to register MDIO bus\n"); 1437 goto out_clk_mdiv; 1438 } 1439 1440 bcm_sf2_gphy_enable_set(priv->dev->ds, false); 1441 1442 ret = bcm_sf2_cfp_rst(priv); 1443 if (ret) { 1444 pr_err("failed to reset CFP\n"); 1445 goto out_mdio; 1446 } 1447 1448 /* Disable all interrupts and request them */ 1449 bcm_sf2_intr_disable(priv); 1450 1451 ret = devm_request_irq(&pdev->dev, priv->irq0, bcm_sf2_switch_0_isr, 0, 1452 "switch_0", ds); 1453 if (ret < 0) { 1454 pr_err("failed to request switch_0 IRQ\n"); 1455 goto out_mdio; 1456 } 1457 1458 ret = devm_request_irq(&pdev->dev, priv->irq1, bcm_sf2_switch_1_isr, 0, 1459 "switch_1", ds); 1460 if (ret < 0) { 1461 pr_err("failed to request switch_1 IRQ\n"); 1462 goto out_mdio; 1463 } 1464 1465 /* Reset the MIB counters */ 1466 reg = core_readl(priv, CORE_GMNCFGCFG); 1467 reg |= RST_MIB_CNT; 1468 core_writel(priv, reg, CORE_GMNCFGCFG); 1469 reg &= ~RST_MIB_CNT; 1470 core_writel(priv, reg, CORE_GMNCFGCFG); 1471 1472 /* Get the maximum number of ports for this switch */ 1473 priv->hw_params.num_ports = core_readl(priv, CORE_IMP0_PRT_ID) + 1; 1474 if (priv->hw_params.num_ports > DSA_MAX_PORTS) 1475 priv->hw_params.num_ports = DSA_MAX_PORTS; 1476 1477 /* Assume a single GPHY setup if we can't read that property */ 1478 if (of_property_read_u32(dn, "brcm,num-gphy", 1479 &priv->hw_params.num_gphy)) 1480 priv->hw_params.num_gphy = 1; 1481 1482 rev = reg_readl(priv, REG_SWITCH_REVISION); 1483 priv->hw_params.top_rev = (rev >> SWITCH_TOP_REV_SHIFT) & 1484 SWITCH_TOP_REV_MASK; 1485 priv->hw_params.core_rev = (rev & SF2_REV_MASK); 1486 1487 rev = reg_readl(priv, REG_PHY_REVISION); 1488 priv->hw_params.gphy_rev = rev & PHY_REVISION_MASK; 1489 1490 ret = b53_switch_register(dev); 1491 if (ret) 1492 goto out_mdio; 1493 1494 dev_info(&pdev->dev, 1495 "Starfighter 2 top: %x.%02x, core: %x.%02x, IRQs: %d, %d\n", 1496 priv->hw_params.top_rev >> 8, priv->hw_params.top_rev & 0xff, 1497 priv->hw_params.core_rev >> 8, priv->hw_params.core_rev & 0xff, 1498 priv->irq0, priv->irq1); 1499 1500 return 0; 1501 1502 out_mdio: 1503 bcm_sf2_mdio_unregister(priv); 1504 out_clk_mdiv: 1505 clk_disable_unprepare(priv->clk_mdiv); 1506 out_clk: 1507 clk_disable_unprepare(priv->clk); 1508 return ret; 1509 } 1510 1511 static int bcm_sf2_sw_remove(struct platform_device *pdev) 1512 { 1513 struct bcm_sf2_priv *priv = platform_get_drvdata(pdev); 1514 1515 if (!priv) 1516 return 0; 1517 1518 priv->wol_ports_mask = 0; 1519 /* Disable interrupts */ 1520 bcm_sf2_intr_disable(priv); 1521 dsa_unregister_switch(priv->dev->ds); 1522 bcm_sf2_cfp_exit(priv->dev->ds); 1523 bcm_sf2_mdio_unregister(priv); 1524 clk_disable_unprepare(priv->clk_mdiv); 1525 clk_disable_unprepare(priv->clk); 1526 if (priv->type == BCM7278_DEVICE_ID) 1527 reset_control_assert(priv->rcdev); 1528 1529 platform_set_drvdata(pdev, NULL); 1530 1531 return 0; 1532 } 1533 1534 static void bcm_sf2_sw_shutdown(struct platform_device *pdev) 1535 { 1536 struct bcm_sf2_priv *priv = platform_get_drvdata(pdev); 1537 1538 if (!priv) 1539 return; 1540 1541 /* For a kernel about to be kexec'd we want to keep the GPHY on for a 1542 * successful MDIO bus scan to occur. If we did turn off the GPHY 1543 * before (e.g: port_disable), this will also power it back on. 1544 * 1545 * Do not rely on kexec_in_progress, just power the PHY on. 1546 */ 1547 if (priv->hw_params.num_gphy == 1) 1548 bcm_sf2_gphy_enable_set(priv->dev->ds, true); 1549 1550 dsa_switch_shutdown(priv->dev->ds); 1551 1552 platform_set_drvdata(pdev, NULL); 1553 } 1554 1555 #ifdef CONFIG_PM_SLEEP 1556 static int bcm_sf2_suspend(struct device *dev) 1557 { 1558 struct bcm_sf2_priv *priv = dev_get_drvdata(dev); 1559 1560 return dsa_switch_suspend(priv->dev->ds); 1561 } 1562 1563 static int bcm_sf2_resume(struct device *dev) 1564 { 1565 struct bcm_sf2_priv *priv = dev_get_drvdata(dev); 1566 1567 return dsa_switch_resume(priv->dev->ds); 1568 } 1569 #endif /* CONFIG_PM_SLEEP */ 1570 1571 static SIMPLE_DEV_PM_OPS(bcm_sf2_pm_ops, 1572 bcm_sf2_suspend, bcm_sf2_resume); 1573 1574 1575 static struct platform_driver bcm_sf2_driver = { 1576 .probe = bcm_sf2_sw_probe, 1577 .remove = bcm_sf2_sw_remove, 1578 .shutdown = bcm_sf2_sw_shutdown, 1579 .driver = { 1580 .name = "brcm-sf2", 1581 .of_match_table = bcm_sf2_of_match, 1582 .pm = &bcm_sf2_pm_ops, 1583 }, 1584 }; 1585 module_platform_driver(bcm_sf2_driver); 1586 1587 MODULE_AUTHOR("Broadcom Corporation"); 1588 MODULE_DESCRIPTION("Driver for Broadcom Starfighter 2 ethernet switch chip"); 1589 MODULE_LICENSE("GPL"); 1590 MODULE_ALIAS("platform:brcm-sf2"); 1591