xref: /openbmc/linux/drivers/net/can/spi/mcp251x.c (revision df0e68c1)
1 // SPDX-License-Identifier: GPL-2.0-only
2 /* CAN bus driver for Microchip 251x/25625 CAN Controller with SPI Interface
3  *
4  * MCP2510 support and bug fixes by Christian Pellegrin
5  * <chripell@evolware.org>
6  *
7  * Copyright 2009 Christian Pellegrin EVOL S.r.l.
8  *
9  * Copyright 2007 Raymarine UK, Ltd. All Rights Reserved.
10  * Written under contract by:
11  *   Chris Elston, Katalix Systems, Ltd.
12  *
13  * Based on Microchip MCP251x CAN controller driver written by
14  * David Vrabel, Copyright 2006 Arcom Control Systems Ltd.
15  *
16  * Based on CAN bus driver for the CCAN controller written by
17  * - Sascha Hauer, Marc Kleine-Budde, Pengutronix
18  * - Simon Kallweit, intefo AG
19  * Copyright 2007
20  */
21 
22 #include <linux/bitfield.h>
23 #include <linux/can/core.h>
24 #include <linux/can/dev.h>
25 #include <linux/can/led.h>
26 #include <linux/clk.h>
27 #include <linux/completion.h>
28 #include <linux/delay.h>
29 #include <linux/device.h>
30 #include <linux/freezer.h>
31 #include <linux/gpio.h>
32 #include <linux/gpio/driver.h>
33 #include <linux/interrupt.h>
34 #include <linux/io.h>
35 #include <linux/iopoll.h>
36 #include <linux/kernel.h>
37 #include <linux/module.h>
38 #include <linux/netdevice.h>
39 #include <linux/platform_device.h>
40 #include <linux/property.h>
41 #include <linux/regulator/consumer.h>
42 #include <linux/slab.h>
43 #include <linux/spi/spi.h>
44 #include <linux/uaccess.h>
45 
46 /* SPI interface instruction set */
47 #define INSTRUCTION_WRITE	0x02
48 #define INSTRUCTION_READ	0x03
49 #define INSTRUCTION_BIT_MODIFY	0x05
50 #define INSTRUCTION_LOAD_TXB(n)	(0x40 + 2 * (n))
51 #define INSTRUCTION_READ_RXB(n)	(((n) == 0) ? 0x90 : 0x94)
52 #define INSTRUCTION_RESET	0xC0
53 #define RTS_TXB0		0x01
54 #define RTS_TXB1		0x02
55 #define RTS_TXB2		0x04
56 #define INSTRUCTION_RTS(n)	(0x80 | ((n) & 0x07))
57 
58 /* MPC251x registers */
59 #define BFPCTRL			0x0c
60 #  define BFPCTRL_B0BFM		BIT(0)
61 #  define BFPCTRL_B1BFM		BIT(1)
62 #  define BFPCTRL_BFM(n)	(BFPCTRL_B0BFM << (n))
63 #  define BFPCTRL_BFM_MASK	GENMASK(1, 0)
64 #  define BFPCTRL_B0BFE		BIT(2)
65 #  define BFPCTRL_B1BFE		BIT(3)
66 #  define BFPCTRL_BFE(n)	(BFPCTRL_B0BFE << (n))
67 #  define BFPCTRL_BFE_MASK	GENMASK(3, 2)
68 #  define BFPCTRL_B0BFS		BIT(4)
69 #  define BFPCTRL_B1BFS		BIT(5)
70 #  define BFPCTRL_BFS(n)	(BFPCTRL_B0BFS << (n))
71 #  define BFPCTRL_BFS_MASK	GENMASK(5, 4)
72 #define TXRTSCTRL		0x0d
73 #  define TXRTSCTRL_B0RTSM	BIT(0)
74 #  define TXRTSCTRL_B1RTSM	BIT(1)
75 #  define TXRTSCTRL_B2RTSM	BIT(2)
76 #  define TXRTSCTRL_RTSM(n)	(TXRTSCTRL_B0RTSM << (n))
77 #  define TXRTSCTRL_RTSM_MASK	GENMASK(2, 0)
78 #  define TXRTSCTRL_B0RTS	BIT(3)
79 #  define TXRTSCTRL_B1RTS	BIT(4)
80 #  define TXRTSCTRL_B2RTS	BIT(5)
81 #  define TXRTSCTRL_RTS(n)	(TXRTSCTRL_B0RTS << (n))
82 #  define TXRTSCTRL_RTS_MASK	GENMASK(5, 3)
83 #define CANSTAT	      0x0e
84 #define CANCTRL	      0x0f
85 #  define CANCTRL_REQOP_MASK	    0xe0
86 #  define CANCTRL_REQOP_CONF	    0x80
87 #  define CANCTRL_REQOP_LISTEN_ONLY 0x60
88 #  define CANCTRL_REQOP_LOOPBACK    0x40
89 #  define CANCTRL_REQOP_SLEEP	    0x20
90 #  define CANCTRL_REQOP_NORMAL	    0x00
91 #  define CANCTRL_OSM		    0x08
92 #  define CANCTRL_ABAT		    0x10
93 #define TEC	      0x1c
94 #define REC	      0x1d
95 #define CNF1	      0x2a
96 #  define CNF1_SJW_SHIFT   6
97 #define CNF2	      0x29
98 #  define CNF2_BTLMODE	   0x80
99 #  define CNF2_SAM         0x40
100 #  define CNF2_PS1_SHIFT   3
101 #define CNF3	      0x28
102 #  define CNF3_SOF	   0x08
103 #  define CNF3_WAKFIL	   0x04
104 #  define CNF3_PHSEG2_MASK 0x07
105 #define CANINTE	      0x2b
106 #  define CANINTE_MERRE 0x80
107 #  define CANINTE_WAKIE 0x40
108 #  define CANINTE_ERRIE 0x20
109 #  define CANINTE_TX2IE 0x10
110 #  define CANINTE_TX1IE 0x08
111 #  define CANINTE_TX0IE 0x04
112 #  define CANINTE_RX1IE 0x02
113 #  define CANINTE_RX0IE 0x01
114 #define CANINTF	      0x2c
115 #  define CANINTF_MERRF 0x80
116 #  define CANINTF_WAKIF 0x40
117 #  define CANINTF_ERRIF 0x20
118 #  define CANINTF_TX2IF 0x10
119 #  define CANINTF_TX1IF 0x08
120 #  define CANINTF_TX0IF 0x04
121 #  define CANINTF_RX1IF 0x02
122 #  define CANINTF_RX0IF 0x01
123 #  define CANINTF_RX (CANINTF_RX0IF | CANINTF_RX1IF)
124 #  define CANINTF_TX (CANINTF_TX2IF | CANINTF_TX1IF | CANINTF_TX0IF)
125 #  define CANINTF_ERR (CANINTF_ERRIF)
126 #define EFLG	      0x2d
127 #  define EFLG_EWARN	0x01
128 #  define EFLG_RXWAR	0x02
129 #  define EFLG_TXWAR	0x04
130 #  define EFLG_RXEP	0x08
131 #  define EFLG_TXEP	0x10
132 #  define EFLG_TXBO	0x20
133 #  define EFLG_RX0OVR	0x40
134 #  define EFLG_RX1OVR	0x80
135 #define TXBCTRL(n)  (((n) * 0x10) + 0x30 + TXBCTRL_OFF)
136 #  define TXBCTRL_ABTF	0x40
137 #  define TXBCTRL_MLOA	0x20
138 #  define TXBCTRL_TXERR 0x10
139 #  define TXBCTRL_TXREQ 0x08
140 #define TXBSIDH(n)  (((n) * 0x10) + 0x30 + TXBSIDH_OFF)
141 #  define SIDH_SHIFT    3
142 #define TXBSIDL(n)  (((n) * 0x10) + 0x30 + TXBSIDL_OFF)
143 #  define SIDL_SID_MASK    7
144 #  define SIDL_SID_SHIFT   5
145 #  define SIDL_EXIDE_SHIFT 3
146 #  define SIDL_EID_SHIFT   16
147 #  define SIDL_EID_MASK    3
148 #define TXBEID8(n)  (((n) * 0x10) + 0x30 + TXBEID8_OFF)
149 #define TXBEID0(n)  (((n) * 0x10) + 0x30 + TXBEID0_OFF)
150 #define TXBDLC(n)   (((n) * 0x10) + 0x30 + TXBDLC_OFF)
151 #  define DLC_RTR_SHIFT    6
152 #define TXBCTRL_OFF 0
153 #define TXBSIDH_OFF 1
154 #define TXBSIDL_OFF 2
155 #define TXBEID8_OFF 3
156 #define TXBEID0_OFF 4
157 #define TXBDLC_OFF  5
158 #define TXBDAT_OFF  6
159 #define RXBCTRL(n)  (((n) * 0x10) + 0x60 + RXBCTRL_OFF)
160 #  define RXBCTRL_BUKT	0x04
161 #  define RXBCTRL_RXM0	0x20
162 #  define RXBCTRL_RXM1	0x40
163 #define RXBSIDH(n)  (((n) * 0x10) + 0x60 + RXBSIDH_OFF)
164 #  define RXBSIDH_SHIFT 3
165 #define RXBSIDL(n)  (((n) * 0x10) + 0x60 + RXBSIDL_OFF)
166 #  define RXBSIDL_IDE   0x08
167 #  define RXBSIDL_SRR   0x10
168 #  define RXBSIDL_EID   3
169 #  define RXBSIDL_SHIFT 5
170 #define RXBEID8(n)  (((n) * 0x10) + 0x60 + RXBEID8_OFF)
171 #define RXBEID0(n)  (((n) * 0x10) + 0x60 + RXBEID0_OFF)
172 #define RXBDLC(n)   (((n) * 0x10) + 0x60 + RXBDLC_OFF)
173 #  define RXBDLC_LEN_MASK  0x0f
174 #  define RXBDLC_RTR       0x40
175 #define RXBCTRL_OFF 0
176 #define RXBSIDH_OFF 1
177 #define RXBSIDL_OFF 2
178 #define RXBEID8_OFF 3
179 #define RXBEID0_OFF 4
180 #define RXBDLC_OFF  5
181 #define RXBDAT_OFF  6
182 #define RXFSID(n) ((n < 3) ? 0 : 4)
183 #define RXFSIDH(n) ((n) * 4 + RXFSID(n))
184 #define RXFSIDL(n) ((n) * 4 + 1 + RXFSID(n))
185 #define RXFEID8(n) ((n) * 4 + 2 + RXFSID(n))
186 #define RXFEID0(n) ((n) * 4 + 3 + RXFSID(n))
187 #define RXMSIDH(n) ((n) * 4 + 0x20)
188 #define RXMSIDL(n) ((n) * 4 + 0x21)
189 #define RXMEID8(n) ((n) * 4 + 0x22)
190 #define RXMEID0(n) ((n) * 4 + 0x23)
191 
192 #define GET_BYTE(val, byte)			\
193 	(((val) >> ((byte) * 8)) & 0xff)
194 #define SET_BYTE(val, byte)			\
195 	(((val) & 0xff) << ((byte) * 8))
196 
197 /* Buffer size required for the largest SPI transfer (i.e., reading a
198  * frame)
199  */
200 #define CAN_FRAME_MAX_DATA_LEN	8
201 #define SPI_TRANSFER_BUF_LEN	(6 + CAN_FRAME_MAX_DATA_LEN)
202 #define CAN_FRAME_MAX_BITS	128
203 
204 #define TX_ECHO_SKB_MAX	1
205 
206 #define MCP251X_OST_DELAY_MS	(5)
207 
208 #define DEVICE_NAME "mcp251x"
209 
210 static const struct can_bittiming_const mcp251x_bittiming_const = {
211 	.name = DEVICE_NAME,
212 	.tseg1_min = 3,
213 	.tseg1_max = 16,
214 	.tseg2_min = 2,
215 	.tseg2_max = 8,
216 	.sjw_max = 4,
217 	.brp_min = 1,
218 	.brp_max = 64,
219 	.brp_inc = 1,
220 };
221 
222 enum mcp251x_model {
223 	CAN_MCP251X_MCP2510	= 0x2510,
224 	CAN_MCP251X_MCP2515	= 0x2515,
225 	CAN_MCP251X_MCP25625	= 0x25625,
226 };
227 
228 struct mcp251x_priv {
229 	struct can_priv	   can;
230 	struct net_device *net;
231 	struct spi_device *spi;
232 	enum mcp251x_model model;
233 
234 	struct mutex mcp_lock; /* SPI device lock */
235 
236 	u8 *spi_tx_buf;
237 	u8 *spi_rx_buf;
238 
239 	struct sk_buff *tx_skb;
240 	int tx_len;
241 
242 	struct workqueue_struct *wq;
243 	struct work_struct tx_work;
244 	struct work_struct restart_work;
245 
246 	int force_quit;
247 	int after_suspend;
248 #define AFTER_SUSPEND_UP 1
249 #define AFTER_SUSPEND_DOWN 2
250 #define AFTER_SUSPEND_POWER 4
251 #define AFTER_SUSPEND_RESTART 8
252 	int restart_tx;
253 	struct regulator *power;
254 	struct regulator *transceiver;
255 	struct clk *clk;
256 #ifdef CONFIG_GPIOLIB
257 	struct gpio_chip gpio;
258 	u8 reg_bfpctrl;
259 #endif
260 };
261 
262 #define MCP251X_IS(_model) \
263 static inline int mcp251x_is_##_model(struct spi_device *spi) \
264 { \
265 	struct mcp251x_priv *priv = spi_get_drvdata(spi); \
266 	return priv->model == CAN_MCP251X_MCP##_model; \
267 }
268 
269 MCP251X_IS(2510);
270 
271 static void mcp251x_clean(struct net_device *net)
272 {
273 	struct mcp251x_priv *priv = netdev_priv(net);
274 
275 	if (priv->tx_skb || priv->tx_len)
276 		net->stats.tx_errors++;
277 	dev_kfree_skb(priv->tx_skb);
278 	if (priv->tx_len)
279 		can_free_echo_skb(priv->net, 0, NULL);
280 	priv->tx_skb = NULL;
281 	priv->tx_len = 0;
282 }
283 
284 /* Note about handling of error return of mcp251x_spi_trans: accessing
285  * registers via SPI is not really different conceptually than using
286  * normal I/O assembler instructions, although it's much more
287  * complicated from a practical POV. So it's not advisable to always
288  * check the return value of this function. Imagine that every
289  * read{b,l}, write{b,l} and friends would be bracketed in "if ( < 0)
290  * error();", it would be a great mess (well there are some situation
291  * when exception handling C++ like could be useful after all). So we
292  * just check that transfers are OK at the beginning of our
293  * conversation with the chip and to avoid doing really nasty things
294  * (like injecting bogus packets in the network stack).
295  */
296 static int mcp251x_spi_trans(struct spi_device *spi, int len)
297 {
298 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
299 	struct spi_transfer t = {
300 		.tx_buf = priv->spi_tx_buf,
301 		.rx_buf = priv->spi_rx_buf,
302 		.len = len,
303 		.cs_change = 0,
304 	};
305 	struct spi_message m;
306 	int ret;
307 
308 	spi_message_init(&m);
309 	spi_message_add_tail(&t, &m);
310 
311 	ret = spi_sync(spi, &m);
312 	if (ret)
313 		dev_err(&spi->dev, "spi transfer failed: ret = %d\n", ret);
314 	return ret;
315 }
316 
317 static int mcp251x_spi_write(struct spi_device *spi, int len)
318 {
319 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
320 	int ret;
321 
322 	ret = spi_write(spi, priv->spi_tx_buf, len);
323 	if (ret)
324 		dev_err(&spi->dev, "spi write failed: ret = %d\n", ret);
325 
326 	return ret;
327 }
328 
329 static u8 mcp251x_read_reg(struct spi_device *spi, u8 reg)
330 {
331 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
332 	u8 val = 0;
333 
334 	priv->spi_tx_buf[0] = INSTRUCTION_READ;
335 	priv->spi_tx_buf[1] = reg;
336 
337 	if (spi->controller->flags & SPI_CONTROLLER_HALF_DUPLEX) {
338 		spi_write_then_read(spi, priv->spi_tx_buf, 2, &val, 1);
339 	} else {
340 		mcp251x_spi_trans(spi, 3);
341 		val = priv->spi_rx_buf[2];
342 	}
343 
344 	return val;
345 }
346 
347 static void mcp251x_read_2regs(struct spi_device *spi, u8 reg, u8 *v1, u8 *v2)
348 {
349 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
350 
351 	priv->spi_tx_buf[0] = INSTRUCTION_READ;
352 	priv->spi_tx_buf[1] = reg;
353 
354 	if (spi->controller->flags & SPI_CONTROLLER_HALF_DUPLEX) {
355 		u8 val[2] = { 0 };
356 
357 		spi_write_then_read(spi, priv->spi_tx_buf, 2, val, 2);
358 		*v1 = val[0];
359 		*v2 = val[1];
360 	} else {
361 		mcp251x_spi_trans(spi, 4);
362 
363 		*v1 = priv->spi_rx_buf[2];
364 		*v2 = priv->spi_rx_buf[3];
365 	}
366 }
367 
368 static void mcp251x_write_reg(struct spi_device *spi, u8 reg, u8 val)
369 {
370 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
371 
372 	priv->spi_tx_buf[0] = INSTRUCTION_WRITE;
373 	priv->spi_tx_buf[1] = reg;
374 	priv->spi_tx_buf[2] = val;
375 
376 	mcp251x_spi_write(spi, 3);
377 }
378 
379 static void mcp251x_write_2regs(struct spi_device *spi, u8 reg, u8 v1, u8 v2)
380 {
381 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
382 
383 	priv->spi_tx_buf[0] = INSTRUCTION_WRITE;
384 	priv->spi_tx_buf[1] = reg;
385 	priv->spi_tx_buf[2] = v1;
386 	priv->spi_tx_buf[3] = v2;
387 
388 	mcp251x_spi_write(spi, 4);
389 }
390 
391 static void mcp251x_write_bits(struct spi_device *spi, u8 reg,
392 			       u8 mask, u8 val)
393 {
394 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
395 
396 	priv->spi_tx_buf[0] = INSTRUCTION_BIT_MODIFY;
397 	priv->spi_tx_buf[1] = reg;
398 	priv->spi_tx_buf[2] = mask;
399 	priv->spi_tx_buf[3] = val;
400 
401 	mcp251x_spi_write(spi, 4);
402 }
403 
404 static u8 mcp251x_read_stat(struct spi_device *spi)
405 {
406 	return mcp251x_read_reg(spi, CANSTAT) & CANCTRL_REQOP_MASK;
407 }
408 
409 #define mcp251x_read_stat_poll_timeout(addr, val, cond, delay_us, timeout_us) \
410 	readx_poll_timeout(mcp251x_read_stat, addr, val, cond, \
411 			   delay_us, timeout_us)
412 
413 #ifdef CONFIG_GPIOLIB
414 enum {
415 	MCP251X_GPIO_TX0RTS = 0,		/* inputs */
416 	MCP251X_GPIO_TX1RTS,
417 	MCP251X_GPIO_TX2RTS,
418 	MCP251X_GPIO_RX0BF,			/* outputs */
419 	MCP251X_GPIO_RX1BF,
420 };
421 
422 #define MCP251X_GPIO_INPUT_MASK \
423 	GENMASK(MCP251X_GPIO_TX2RTS, MCP251X_GPIO_TX0RTS)
424 #define MCP251X_GPIO_OUTPUT_MASK \
425 	GENMASK(MCP251X_GPIO_RX1BF, MCP251X_GPIO_RX0BF)
426 
427 static const char * const mcp251x_gpio_names[] = {
428 	[MCP251X_GPIO_TX0RTS] = "TX0RTS",	/* inputs */
429 	[MCP251X_GPIO_TX1RTS] = "TX1RTS",
430 	[MCP251X_GPIO_TX2RTS] = "TX2RTS",
431 	[MCP251X_GPIO_RX0BF] = "RX0BF",		/* outputs */
432 	[MCP251X_GPIO_RX1BF] = "RX1BF",
433 };
434 
435 static inline bool mcp251x_gpio_is_input(unsigned int offset)
436 {
437 	return offset <= MCP251X_GPIO_TX2RTS;
438 }
439 
440 static int mcp251x_gpio_request(struct gpio_chip *chip,
441 				unsigned int offset)
442 {
443 	struct mcp251x_priv *priv = gpiochip_get_data(chip);
444 	u8 val;
445 
446 	/* nothing to be done for inputs */
447 	if (mcp251x_gpio_is_input(offset))
448 		return 0;
449 
450 	val = BFPCTRL_BFE(offset - MCP251X_GPIO_RX0BF);
451 
452 	mutex_lock(&priv->mcp_lock);
453 	mcp251x_write_bits(priv->spi, BFPCTRL, val, val);
454 	mutex_unlock(&priv->mcp_lock);
455 
456 	priv->reg_bfpctrl |= val;
457 
458 	return 0;
459 }
460 
461 static void mcp251x_gpio_free(struct gpio_chip *chip,
462 			      unsigned int offset)
463 {
464 	struct mcp251x_priv *priv = gpiochip_get_data(chip);
465 	u8 val;
466 
467 	/* nothing to be done for inputs */
468 	if (mcp251x_gpio_is_input(offset))
469 		return;
470 
471 	val = BFPCTRL_BFE(offset - MCP251X_GPIO_RX0BF);
472 
473 	mutex_lock(&priv->mcp_lock);
474 	mcp251x_write_bits(priv->spi, BFPCTRL, val, 0);
475 	mutex_unlock(&priv->mcp_lock);
476 
477 	priv->reg_bfpctrl &= ~val;
478 }
479 
480 static int mcp251x_gpio_get_direction(struct gpio_chip *chip,
481 				      unsigned int offset)
482 {
483 	if (mcp251x_gpio_is_input(offset))
484 		return GPIOF_DIR_IN;
485 
486 	return GPIOF_DIR_OUT;
487 }
488 
489 static int mcp251x_gpio_get(struct gpio_chip *chip, unsigned int offset)
490 {
491 	struct mcp251x_priv *priv = gpiochip_get_data(chip);
492 	u8 reg, mask, val;
493 
494 	if (mcp251x_gpio_is_input(offset)) {
495 		reg = TXRTSCTRL;
496 		mask = TXRTSCTRL_RTS(offset);
497 	} else {
498 		reg = BFPCTRL;
499 		mask = BFPCTRL_BFS(offset - MCP251X_GPIO_RX0BF);
500 	}
501 
502 	mutex_lock(&priv->mcp_lock);
503 	val = mcp251x_read_reg(priv->spi, reg);
504 	mutex_unlock(&priv->mcp_lock);
505 
506 	return !!(val & mask);
507 }
508 
509 static int mcp251x_gpio_get_multiple(struct gpio_chip *chip,
510 				     unsigned long *maskp, unsigned long *bitsp)
511 {
512 	struct mcp251x_priv *priv = gpiochip_get_data(chip);
513 	unsigned long bits = 0;
514 	u8 val;
515 
516 	mutex_lock(&priv->mcp_lock);
517 	if (maskp[0] & MCP251X_GPIO_INPUT_MASK) {
518 		val = mcp251x_read_reg(priv->spi, TXRTSCTRL);
519 		val = FIELD_GET(TXRTSCTRL_RTS_MASK, val);
520 		bits |= FIELD_PREP(MCP251X_GPIO_INPUT_MASK, val);
521 	}
522 	if (maskp[0] & MCP251X_GPIO_OUTPUT_MASK) {
523 		val = mcp251x_read_reg(priv->spi, BFPCTRL);
524 		val = FIELD_GET(BFPCTRL_BFS_MASK, val);
525 		bits |= FIELD_PREP(MCP251X_GPIO_OUTPUT_MASK, val);
526 	}
527 	mutex_unlock(&priv->mcp_lock);
528 
529 	bitsp[0] = bits;
530 	return 0;
531 }
532 
533 static void mcp251x_gpio_set(struct gpio_chip *chip, unsigned int offset,
534 			     int value)
535 {
536 	struct mcp251x_priv *priv = gpiochip_get_data(chip);
537 	u8 mask, val;
538 
539 	mask = BFPCTRL_BFS(offset - MCP251X_GPIO_RX0BF);
540 	val = value ? mask : 0;
541 
542 	mutex_lock(&priv->mcp_lock);
543 	mcp251x_write_bits(priv->spi, BFPCTRL, mask, val);
544 	mutex_unlock(&priv->mcp_lock);
545 
546 	priv->reg_bfpctrl &= ~mask;
547 	priv->reg_bfpctrl |= val;
548 }
549 
550 static void
551 mcp251x_gpio_set_multiple(struct gpio_chip *chip,
552 			  unsigned long *maskp, unsigned long *bitsp)
553 {
554 	struct mcp251x_priv *priv = gpiochip_get_data(chip);
555 	u8 mask, val;
556 
557 	mask = FIELD_GET(MCP251X_GPIO_OUTPUT_MASK, maskp[0]);
558 	mask = FIELD_PREP(BFPCTRL_BFS_MASK, mask);
559 
560 	val = FIELD_GET(MCP251X_GPIO_OUTPUT_MASK, bitsp[0]);
561 	val = FIELD_PREP(BFPCTRL_BFS_MASK, val);
562 
563 	if (!mask)
564 		return;
565 
566 	mutex_lock(&priv->mcp_lock);
567 	mcp251x_write_bits(priv->spi, BFPCTRL, mask, val);
568 	mutex_unlock(&priv->mcp_lock);
569 
570 	priv->reg_bfpctrl &= ~mask;
571 	priv->reg_bfpctrl |= val;
572 }
573 
574 static void mcp251x_gpio_restore(struct spi_device *spi)
575 {
576 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
577 
578 	mcp251x_write_reg(spi, BFPCTRL, priv->reg_bfpctrl);
579 }
580 
581 static int mcp251x_gpio_setup(struct mcp251x_priv *priv)
582 {
583 	struct gpio_chip *gpio = &priv->gpio;
584 
585 	if (!device_property_present(&priv->spi->dev, "gpio-controller"))
586 		return 0;
587 
588 	/* gpiochip handles TX[0..2]RTS and RX[0..1]BF */
589 	gpio->label = priv->spi->modalias;
590 	gpio->parent = &priv->spi->dev;
591 	gpio->owner = THIS_MODULE;
592 	gpio->request = mcp251x_gpio_request;
593 	gpio->free = mcp251x_gpio_free;
594 	gpio->get_direction = mcp251x_gpio_get_direction;
595 	gpio->get = mcp251x_gpio_get;
596 	gpio->get_multiple = mcp251x_gpio_get_multiple;
597 	gpio->set = mcp251x_gpio_set;
598 	gpio->set_multiple = mcp251x_gpio_set_multiple;
599 	gpio->base = -1;
600 	gpio->ngpio = ARRAY_SIZE(mcp251x_gpio_names);
601 	gpio->names = mcp251x_gpio_names;
602 	gpio->can_sleep = true;
603 #ifdef CONFIG_OF_GPIO
604 	gpio->of_node = priv->spi->dev.of_node;
605 #endif
606 
607 	return devm_gpiochip_add_data(&priv->spi->dev, gpio, priv);
608 }
609 #else
610 static inline void mcp251x_gpio_restore(struct spi_device *spi)
611 {
612 }
613 
614 static inline int mcp251x_gpio_setup(struct mcp251x_priv *priv)
615 {
616 	return 0;
617 }
618 #endif
619 
620 static void mcp251x_hw_tx_frame(struct spi_device *spi, u8 *buf,
621 				int len, int tx_buf_idx)
622 {
623 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
624 
625 	if (mcp251x_is_2510(spi)) {
626 		int i;
627 
628 		for (i = 1; i < TXBDAT_OFF + len; i++)
629 			mcp251x_write_reg(spi, TXBCTRL(tx_buf_idx) + i,
630 					  buf[i]);
631 	} else {
632 		memcpy(priv->spi_tx_buf, buf, TXBDAT_OFF + len);
633 		mcp251x_spi_write(spi, TXBDAT_OFF + len);
634 	}
635 }
636 
637 static void mcp251x_hw_tx(struct spi_device *spi, struct can_frame *frame,
638 			  int tx_buf_idx)
639 {
640 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
641 	u32 sid, eid, exide, rtr;
642 	u8 buf[SPI_TRANSFER_BUF_LEN];
643 
644 	exide = (frame->can_id & CAN_EFF_FLAG) ? 1 : 0; /* Extended ID Enable */
645 	if (exide)
646 		sid = (frame->can_id & CAN_EFF_MASK) >> 18;
647 	else
648 		sid = frame->can_id & CAN_SFF_MASK; /* Standard ID */
649 	eid = frame->can_id & CAN_EFF_MASK; /* Extended ID */
650 	rtr = (frame->can_id & CAN_RTR_FLAG) ? 1 : 0; /* Remote transmission */
651 
652 	buf[TXBCTRL_OFF] = INSTRUCTION_LOAD_TXB(tx_buf_idx);
653 	buf[TXBSIDH_OFF] = sid >> SIDH_SHIFT;
654 	buf[TXBSIDL_OFF] = ((sid & SIDL_SID_MASK) << SIDL_SID_SHIFT) |
655 		(exide << SIDL_EXIDE_SHIFT) |
656 		((eid >> SIDL_EID_SHIFT) & SIDL_EID_MASK);
657 	buf[TXBEID8_OFF] = GET_BYTE(eid, 1);
658 	buf[TXBEID0_OFF] = GET_BYTE(eid, 0);
659 	buf[TXBDLC_OFF] = (rtr << DLC_RTR_SHIFT) | frame->len;
660 	memcpy(buf + TXBDAT_OFF, frame->data, frame->len);
661 	mcp251x_hw_tx_frame(spi, buf, frame->len, tx_buf_idx);
662 
663 	/* use INSTRUCTION_RTS, to avoid "repeated frame problem" */
664 	priv->spi_tx_buf[0] = INSTRUCTION_RTS(1 << tx_buf_idx);
665 	mcp251x_spi_write(priv->spi, 1);
666 }
667 
668 static void mcp251x_hw_rx_frame(struct spi_device *spi, u8 *buf,
669 				int buf_idx)
670 {
671 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
672 
673 	if (mcp251x_is_2510(spi)) {
674 		int i, len;
675 
676 		for (i = 1; i < RXBDAT_OFF; i++)
677 			buf[i] = mcp251x_read_reg(spi, RXBCTRL(buf_idx) + i);
678 
679 		len = can_cc_dlc2len(buf[RXBDLC_OFF] & RXBDLC_LEN_MASK);
680 		for (; i < (RXBDAT_OFF + len); i++)
681 			buf[i] = mcp251x_read_reg(spi, RXBCTRL(buf_idx) + i);
682 	} else {
683 		priv->spi_tx_buf[RXBCTRL_OFF] = INSTRUCTION_READ_RXB(buf_idx);
684 		if (spi->controller->flags & SPI_CONTROLLER_HALF_DUPLEX) {
685 			spi_write_then_read(spi, priv->spi_tx_buf, 1,
686 					    priv->spi_rx_buf,
687 					    SPI_TRANSFER_BUF_LEN);
688 			memcpy(buf + 1, priv->spi_rx_buf,
689 			       SPI_TRANSFER_BUF_LEN - 1);
690 		} else {
691 			mcp251x_spi_trans(spi, SPI_TRANSFER_BUF_LEN);
692 			memcpy(buf, priv->spi_rx_buf, SPI_TRANSFER_BUF_LEN);
693 		}
694 	}
695 }
696 
697 static void mcp251x_hw_rx(struct spi_device *spi, int buf_idx)
698 {
699 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
700 	struct sk_buff *skb;
701 	struct can_frame *frame;
702 	u8 buf[SPI_TRANSFER_BUF_LEN];
703 
704 	skb = alloc_can_skb(priv->net, &frame);
705 	if (!skb) {
706 		dev_err(&spi->dev, "cannot allocate RX skb\n");
707 		priv->net->stats.rx_dropped++;
708 		return;
709 	}
710 
711 	mcp251x_hw_rx_frame(spi, buf, buf_idx);
712 	if (buf[RXBSIDL_OFF] & RXBSIDL_IDE) {
713 		/* Extended ID format */
714 		frame->can_id = CAN_EFF_FLAG;
715 		frame->can_id |=
716 			/* Extended ID part */
717 			SET_BYTE(buf[RXBSIDL_OFF] & RXBSIDL_EID, 2) |
718 			SET_BYTE(buf[RXBEID8_OFF], 1) |
719 			SET_BYTE(buf[RXBEID0_OFF], 0) |
720 			/* Standard ID part */
721 			(((buf[RXBSIDH_OFF] << RXBSIDH_SHIFT) |
722 			  (buf[RXBSIDL_OFF] >> RXBSIDL_SHIFT)) << 18);
723 		/* Remote transmission request */
724 		if (buf[RXBDLC_OFF] & RXBDLC_RTR)
725 			frame->can_id |= CAN_RTR_FLAG;
726 	} else {
727 		/* Standard ID format */
728 		frame->can_id =
729 			(buf[RXBSIDH_OFF] << RXBSIDH_SHIFT) |
730 			(buf[RXBSIDL_OFF] >> RXBSIDL_SHIFT);
731 		if (buf[RXBSIDL_OFF] & RXBSIDL_SRR)
732 			frame->can_id |= CAN_RTR_FLAG;
733 	}
734 	/* Data length */
735 	frame->len = can_cc_dlc2len(buf[RXBDLC_OFF] & RXBDLC_LEN_MASK);
736 	memcpy(frame->data, buf + RXBDAT_OFF, frame->len);
737 
738 	priv->net->stats.rx_packets++;
739 	priv->net->stats.rx_bytes += frame->len;
740 
741 	can_led_event(priv->net, CAN_LED_EVENT_RX);
742 
743 	netif_rx_ni(skb);
744 }
745 
746 static void mcp251x_hw_sleep(struct spi_device *spi)
747 {
748 	mcp251x_write_reg(spi, CANCTRL, CANCTRL_REQOP_SLEEP);
749 }
750 
751 /* May only be called when device is sleeping! */
752 static int mcp251x_hw_wake(struct spi_device *spi)
753 {
754 	u8 value;
755 	int ret;
756 
757 	/* Force wakeup interrupt to wake device, but don't execute IST */
758 	disable_irq(spi->irq);
759 	mcp251x_write_2regs(spi, CANINTE, CANINTE_WAKIE, CANINTF_WAKIF);
760 
761 	/* Wait for oscillator startup timer after wake up */
762 	mdelay(MCP251X_OST_DELAY_MS);
763 
764 	/* Put device into config mode */
765 	mcp251x_write_reg(spi, CANCTRL, CANCTRL_REQOP_CONF);
766 
767 	/* Wait for the device to enter config mode */
768 	ret = mcp251x_read_stat_poll_timeout(spi, value, value == CANCTRL_REQOP_CONF,
769 					     MCP251X_OST_DELAY_MS * 1000,
770 					     USEC_PER_SEC);
771 	if (ret) {
772 		dev_err(&spi->dev, "MCP251x didn't enter in config mode\n");
773 		return ret;
774 	}
775 
776 	/* Disable and clear pending interrupts */
777 	mcp251x_write_2regs(spi, CANINTE, 0x00, 0x00);
778 	enable_irq(spi->irq);
779 
780 	return 0;
781 }
782 
783 static netdev_tx_t mcp251x_hard_start_xmit(struct sk_buff *skb,
784 					   struct net_device *net)
785 {
786 	struct mcp251x_priv *priv = netdev_priv(net);
787 	struct spi_device *spi = priv->spi;
788 
789 	if (priv->tx_skb || priv->tx_len) {
790 		dev_warn(&spi->dev, "hard_xmit called while tx busy\n");
791 		return NETDEV_TX_BUSY;
792 	}
793 
794 	if (can_dropped_invalid_skb(net, skb))
795 		return NETDEV_TX_OK;
796 
797 	netif_stop_queue(net);
798 	priv->tx_skb = skb;
799 	queue_work(priv->wq, &priv->tx_work);
800 
801 	return NETDEV_TX_OK;
802 }
803 
804 static int mcp251x_do_set_mode(struct net_device *net, enum can_mode mode)
805 {
806 	struct mcp251x_priv *priv = netdev_priv(net);
807 
808 	switch (mode) {
809 	case CAN_MODE_START:
810 		mcp251x_clean(net);
811 		/* We have to delay work since SPI I/O may sleep */
812 		priv->can.state = CAN_STATE_ERROR_ACTIVE;
813 		priv->restart_tx = 1;
814 		if (priv->can.restart_ms == 0)
815 			priv->after_suspend = AFTER_SUSPEND_RESTART;
816 		queue_work(priv->wq, &priv->restart_work);
817 		break;
818 	default:
819 		return -EOPNOTSUPP;
820 	}
821 
822 	return 0;
823 }
824 
825 static int mcp251x_set_normal_mode(struct spi_device *spi)
826 {
827 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
828 	u8 value;
829 	int ret;
830 
831 	/* Enable interrupts */
832 	mcp251x_write_reg(spi, CANINTE,
833 			  CANINTE_ERRIE | CANINTE_TX2IE | CANINTE_TX1IE |
834 			  CANINTE_TX0IE | CANINTE_RX1IE | CANINTE_RX0IE);
835 
836 	if (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK) {
837 		/* Put device into loopback mode */
838 		mcp251x_write_reg(spi, CANCTRL, CANCTRL_REQOP_LOOPBACK);
839 	} else if (priv->can.ctrlmode & CAN_CTRLMODE_LISTENONLY) {
840 		/* Put device into listen-only mode */
841 		mcp251x_write_reg(spi, CANCTRL, CANCTRL_REQOP_LISTEN_ONLY);
842 	} else {
843 		/* Put device into normal mode */
844 		mcp251x_write_reg(spi, CANCTRL, CANCTRL_REQOP_NORMAL);
845 
846 		/* Wait for the device to enter normal mode */
847 		ret = mcp251x_read_stat_poll_timeout(spi, value, value == 0,
848 						     MCP251X_OST_DELAY_MS * 1000,
849 						     USEC_PER_SEC);
850 		if (ret) {
851 			dev_err(&spi->dev, "MCP251x didn't enter in normal mode\n");
852 			return ret;
853 		}
854 	}
855 	priv->can.state = CAN_STATE_ERROR_ACTIVE;
856 	return 0;
857 }
858 
859 static int mcp251x_do_set_bittiming(struct net_device *net)
860 {
861 	struct mcp251x_priv *priv = netdev_priv(net);
862 	struct can_bittiming *bt = &priv->can.bittiming;
863 	struct spi_device *spi = priv->spi;
864 
865 	mcp251x_write_reg(spi, CNF1, ((bt->sjw - 1) << CNF1_SJW_SHIFT) |
866 			  (bt->brp - 1));
867 	mcp251x_write_reg(spi, CNF2, CNF2_BTLMODE |
868 			  (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES ?
869 			   CNF2_SAM : 0) |
870 			  ((bt->phase_seg1 - 1) << CNF2_PS1_SHIFT) |
871 			  (bt->prop_seg - 1));
872 	mcp251x_write_bits(spi, CNF3, CNF3_PHSEG2_MASK,
873 			   (bt->phase_seg2 - 1));
874 	dev_dbg(&spi->dev, "CNF: 0x%02x 0x%02x 0x%02x\n",
875 		mcp251x_read_reg(spi, CNF1),
876 		mcp251x_read_reg(spi, CNF2),
877 		mcp251x_read_reg(spi, CNF3));
878 
879 	return 0;
880 }
881 
882 static int mcp251x_setup(struct net_device *net, struct spi_device *spi)
883 {
884 	mcp251x_do_set_bittiming(net);
885 
886 	mcp251x_write_reg(spi, RXBCTRL(0),
887 			  RXBCTRL_BUKT | RXBCTRL_RXM0 | RXBCTRL_RXM1);
888 	mcp251x_write_reg(spi, RXBCTRL(1),
889 			  RXBCTRL_RXM0 | RXBCTRL_RXM1);
890 	return 0;
891 }
892 
893 static int mcp251x_hw_reset(struct spi_device *spi)
894 {
895 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
896 	u8 value;
897 	int ret;
898 
899 	/* Wait for oscillator startup timer after power up */
900 	mdelay(MCP251X_OST_DELAY_MS);
901 
902 	priv->spi_tx_buf[0] = INSTRUCTION_RESET;
903 	ret = mcp251x_spi_write(spi, 1);
904 	if (ret)
905 		return ret;
906 
907 	/* Wait for oscillator startup timer after reset */
908 	mdelay(MCP251X_OST_DELAY_MS);
909 
910 	/* Wait for reset to finish */
911 	ret = mcp251x_read_stat_poll_timeout(spi, value, value == CANCTRL_REQOP_CONF,
912 					     MCP251X_OST_DELAY_MS * 1000,
913 					     USEC_PER_SEC);
914 	if (ret)
915 		dev_err(&spi->dev, "MCP251x didn't enter in conf mode after reset\n");
916 	return ret;
917 }
918 
919 static int mcp251x_hw_probe(struct spi_device *spi)
920 {
921 	u8 ctrl;
922 	int ret;
923 
924 	ret = mcp251x_hw_reset(spi);
925 	if (ret)
926 		return ret;
927 
928 	ctrl = mcp251x_read_reg(spi, CANCTRL);
929 
930 	dev_dbg(&spi->dev, "CANCTRL 0x%02x\n", ctrl);
931 
932 	/* Check for power up default value */
933 	if ((ctrl & 0x17) != 0x07)
934 		return -ENODEV;
935 
936 	return 0;
937 }
938 
939 static int mcp251x_power_enable(struct regulator *reg, int enable)
940 {
941 	if (IS_ERR_OR_NULL(reg))
942 		return 0;
943 
944 	if (enable)
945 		return regulator_enable(reg);
946 	else
947 		return regulator_disable(reg);
948 }
949 
950 static int mcp251x_stop(struct net_device *net)
951 {
952 	struct mcp251x_priv *priv = netdev_priv(net);
953 	struct spi_device *spi = priv->spi;
954 
955 	close_candev(net);
956 
957 	priv->force_quit = 1;
958 	free_irq(spi->irq, priv);
959 
960 	mutex_lock(&priv->mcp_lock);
961 
962 	/* Disable and clear pending interrupts */
963 	mcp251x_write_2regs(spi, CANINTE, 0x00, 0x00);
964 
965 	mcp251x_write_reg(spi, TXBCTRL(0), 0);
966 	mcp251x_clean(net);
967 
968 	mcp251x_hw_sleep(spi);
969 
970 	mcp251x_power_enable(priv->transceiver, 0);
971 
972 	priv->can.state = CAN_STATE_STOPPED;
973 
974 	mutex_unlock(&priv->mcp_lock);
975 
976 	can_led_event(net, CAN_LED_EVENT_STOP);
977 
978 	return 0;
979 }
980 
981 static void mcp251x_error_skb(struct net_device *net, int can_id, int data1)
982 {
983 	struct sk_buff *skb;
984 	struct can_frame *frame;
985 
986 	skb = alloc_can_err_skb(net, &frame);
987 	if (skb) {
988 		frame->can_id |= can_id;
989 		frame->data[1] = data1;
990 		netif_rx_ni(skb);
991 	} else {
992 		netdev_err(net, "cannot allocate error skb\n");
993 	}
994 }
995 
996 static void mcp251x_tx_work_handler(struct work_struct *ws)
997 {
998 	struct mcp251x_priv *priv = container_of(ws, struct mcp251x_priv,
999 						 tx_work);
1000 	struct spi_device *spi = priv->spi;
1001 	struct net_device *net = priv->net;
1002 	struct can_frame *frame;
1003 
1004 	mutex_lock(&priv->mcp_lock);
1005 	if (priv->tx_skb) {
1006 		if (priv->can.state == CAN_STATE_BUS_OFF) {
1007 			mcp251x_clean(net);
1008 		} else {
1009 			frame = (struct can_frame *)priv->tx_skb->data;
1010 
1011 			if (frame->len > CAN_FRAME_MAX_DATA_LEN)
1012 				frame->len = CAN_FRAME_MAX_DATA_LEN;
1013 			mcp251x_hw_tx(spi, frame, 0);
1014 			priv->tx_len = 1 + frame->len;
1015 			can_put_echo_skb(priv->tx_skb, net, 0, 0);
1016 			priv->tx_skb = NULL;
1017 		}
1018 	}
1019 	mutex_unlock(&priv->mcp_lock);
1020 }
1021 
1022 static void mcp251x_restart_work_handler(struct work_struct *ws)
1023 {
1024 	struct mcp251x_priv *priv = container_of(ws, struct mcp251x_priv,
1025 						 restart_work);
1026 	struct spi_device *spi = priv->spi;
1027 	struct net_device *net = priv->net;
1028 
1029 	mutex_lock(&priv->mcp_lock);
1030 	if (priv->after_suspend) {
1031 		if (priv->after_suspend & AFTER_SUSPEND_POWER) {
1032 			mcp251x_hw_reset(spi);
1033 			mcp251x_setup(net, spi);
1034 			mcp251x_gpio_restore(spi);
1035 		} else {
1036 			mcp251x_hw_wake(spi);
1037 		}
1038 		priv->force_quit = 0;
1039 		if (priv->after_suspend & AFTER_SUSPEND_RESTART) {
1040 			mcp251x_set_normal_mode(spi);
1041 		} else if (priv->after_suspend & AFTER_SUSPEND_UP) {
1042 			netif_device_attach(net);
1043 			mcp251x_clean(net);
1044 			mcp251x_set_normal_mode(spi);
1045 			netif_wake_queue(net);
1046 		} else {
1047 			mcp251x_hw_sleep(spi);
1048 		}
1049 		priv->after_suspend = 0;
1050 	}
1051 
1052 	if (priv->restart_tx) {
1053 		priv->restart_tx = 0;
1054 		mcp251x_write_reg(spi, TXBCTRL(0), 0);
1055 		mcp251x_clean(net);
1056 		netif_wake_queue(net);
1057 		mcp251x_error_skb(net, CAN_ERR_RESTARTED, 0);
1058 	}
1059 	mutex_unlock(&priv->mcp_lock);
1060 }
1061 
1062 static irqreturn_t mcp251x_can_ist(int irq, void *dev_id)
1063 {
1064 	struct mcp251x_priv *priv = dev_id;
1065 	struct spi_device *spi = priv->spi;
1066 	struct net_device *net = priv->net;
1067 
1068 	mutex_lock(&priv->mcp_lock);
1069 	while (!priv->force_quit) {
1070 		enum can_state new_state;
1071 		u8 intf, eflag;
1072 		u8 clear_intf = 0;
1073 		int can_id = 0, data1 = 0;
1074 
1075 		mcp251x_read_2regs(spi, CANINTF, &intf, &eflag);
1076 
1077 		/* mask out flags we don't care about */
1078 		intf &= CANINTF_RX | CANINTF_TX | CANINTF_ERR;
1079 
1080 		/* receive buffer 0 */
1081 		if (intf & CANINTF_RX0IF) {
1082 			mcp251x_hw_rx(spi, 0);
1083 			/* Free one buffer ASAP
1084 			 * (The MCP2515/25625 does this automatically.)
1085 			 */
1086 			if (mcp251x_is_2510(spi))
1087 				mcp251x_write_bits(spi, CANINTF,
1088 						   CANINTF_RX0IF, 0x00);
1089 		}
1090 
1091 		/* receive buffer 1 */
1092 		if (intf & CANINTF_RX1IF) {
1093 			mcp251x_hw_rx(spi, 1);
1094 			/* The MCP2515/25625 does this automatically. */
1095 			if (mcp251x_is_2510(spi))
1096 				clear_intf |= CANINTF_RX1IF;
1097 		}
1098 
1099 		/* any error or tx interrupt we need to clear? */
1100 		if (intf & (CANINTF_ERR | CANINTF_TX))
1101 			clear_intf |= intf & (CANINTF_ERR | CANINTF_TX);
1102 		if (clear_intf)
1103 			mcp251x_write_bits(spi, CANINTF, clear_intf, 0x00);
1104 
1105 		if (eflag & (EFLG_RX0OVR | EFLG_RX1OVR))
1106 			mcp251x_write_bits(spi, EFLG, eflag, 0x00);
1107 
1108 		/* Update can state */
1109 		if (eflag & EFLG_TXBO) {
1110 			new_state = CAN_STATE_BUS_OFF;
1111 			can_id |= CAN_ERR_BUSOFF;
1112 		} else if (eflag & EFLG_TXEP) {
1113 			new_state = CAN_STATE_ERROR_PASSIVE;
1114 			can_id |= CAN_ERR_CRTL;
1115 			data1 |= CAN_ERR_CRTL_TX_PASSIVE;
1116 		} else if (eflag & EFLG_RXEP) {
1117 			new_state = CAN_STATE_ERROR_PASSIVE;
1118 			can_id |= CAN_ERR_CRTL;
1119 			data1 |= CAN_ERR_CRTL_RX_PASSIVE;
1120 		} else if (eflag & EFLG_TXWAR) {
1121 			new_state = CAN_STATE_ERROR_WARNING;
1122 			can_id |= CAN_ERR_CRTL;
1123 			data1 |= CAN_ERR_CRTL_TX_WARNING;
1124 		} else if (eflag & EFLG_RXWAR) {
1125 			new_state = CAN_STATE_ERROR_WARNING;
1126 			can_id |= CAN_ERR_CRTL;
1127 			data1 |= CAN_ERR_CRTL_RX_WARNING;
1128 		} else {
1129 			new_state = CAN_STATE_ERROR_ACTIVE;
1130 		}
1131 
1132 		/* Update can state statistics */
1133 		switch (priv->can.state) {
1134 		case CAN_STATE_ERROR_ACTIVE:
1135 			if (new_state >= CAN_STATE_ERROR_WARNING &&
1136 			    new_state <= CAN_STATE_BUS_OFF)
1137 				priv->can.can_stats.error_warning++;
1138 			fallthrough;
1139 		case CAN_STATE_ERROR_WARNING:
1140 			if (new_state >= CAN_STATE_ERROR_PASSIVE &&
1141 			    new_state <= CAN_STATE_BUS_OFF)
1142 				priv->can.can_stats.error_passive++;
1143 			break;
1144 		default:
1145 			break;
1146 		}
1147 		priv->can.state = new_state;
1148 
1149 		if (intf & CANINTF_ERRIF) {
1150 			/* Handle overflow counters */
1151 			if (eflag & (EFLG_RX0OVR | EFLG_RX1OVR)) {
1152 				if (eflag & EFLG_RX0OVR) {
1153 					net->stats.rx_over_errors++;
1154 					net->stats.rx_errors++;
1155 				}
1156 				if (eflag & EFLG_RX1OVR) {
1157 					net->stats.rx_over_errors++;
1158 					net->stats.rx_errors++;
1159 				}
1160 				can_id |= CAN_ERR_CRTL;
1161 				data1 |= CAN_ERR_CRTL_RX_OVERFLOW;
1162 			}
1163 			mcp251x_error_skb(net, can_id, data1);
1164 		}
1165 
1166 		if (priv->can.state == CAN_STATE_BUS_OFF) {
1167 			if (priv->can.restart_ms == 0) {
1168 				priv->force_quit = 1;
1169 				priv->can.can_stats.bus_off++;
1170 				can_bus_off(net);
1171 				mcp251x_hw_sleep(spi);
1172 				break;
1173 			}
1174 		}
1175 
1176 		if (intf == 0)
1177 			break;
1178 
1179 		if (intf & CANINTF_TX) {
1180 			net->stats.tx_packets++;
1181 			net->stats.tx_bytes += priv->tx_len - 1;
1182 			can_led_event(net, CAN_LED_EVENT_TX);
1183 			if (priv->tx_len) {
1184 				can_get_echo_skb(net, 0, NULL);
1185 				priv->tx_len = 0;
1186 			}
1187 			netif_wake_queue(net);
1188 		}
1189 	}
1190 	mutex_unlock(&priv->mcp_lock);
1191 	return IRQ_HANDLED;
1192 }
1193 
1194 static int mcp251x_open(struct net_device *net)
1195 {
1196 	struct mcp251x_priv *priv = netdev_priv(net);
1197 	struct spi_device *spi = priv->spi;
1198 	unsigned long flags = 0;
1199 	int ret;
1200 
1201 	ret = open_candev(net);
1202 	if (ret) {
1203 		dev_err(&spi->dev, "unable to set initial baudrate!\n");
1204 		return ret;
1205 	}
1206 
1207 	mutex_lock(&priv->mcp_lock);
1208 	mcp251x_power_enable(priv->transceiver, 1);
1209 
1210 	priv->force_quit = 0;
1211 	priv->tx_skb = NULL;
1212 	priv->tx_len = 0;
1213 
1214 	if (!dev_fwnode(&spi->dev))
1215 		flags = IRQF_TRIGGER_FALLING;
1216 
1217 	ret = request_threaded_irq(spi->irq, NULL, mcp251x_can_ist,
1218 				   flags | IRQF_ONESHOT, dev_name(&spi->dev),
1219 				   priv);
1220 	if (ret) {
1221 		dev_err(&spi->dev, "failed to acquire irq %d\n", spi->irq);
1222 		goto out_close;
1223 	}
1224 
1225 	ret = mcp251x_hw_wake(spi);
1226 	if (ret)
1227 		goto out_free_irq;
1228 	ret = mcp251x_setup(net, spi);
1229 	if (ret)
1230 		goto out_free_irq;
1231 	ret = mcp251x_set_normal_mode(spi);
1232 	if (ret)
1233 		goto out_free_irq;
1234 
1235 	can_led_event(net, CAN_LED_EVENT_OPEN);
1236 
1237 	netif_wake_queue(net);
1238 	mutex_unlock(&priv->mcp_lock);
1239 
1240 	return 0;
1241 
1242 out_free_irq:
1243 	free_irq(spi->irq, priv);
1244 	mcp251x_hw_sleep(spi);
1245 out_close:
1246 	mcp251x_power_enable(priv->transceiver, 0);
1247 	close_candev(net);
1248 	mutex_unlock(&priv->mcp_lock);
1249 	return ret;
1250 }
1251 
1252 static const struct net_device_ops mcp251x_netdev_ops = {
1253 	.ndo_open = mcp251x_open,
1254 	.ndo_stop = mcp251x_stop,
1255 	.ndo_start_xmit = mcp251x_hard_start_xmit,
1256 	.ndo_change_mtu = can_change_mtu,
1257 };
1258 
1259 static const struct of_device_id mcp251x_of_match[] = {
1260 	{
1261 		.compatible	= "microchip,mcp2510",
1262 		.data		= (void *)CAN_MCP251X_MCP2510,
1263 	},
1264 	{
1265 		.compatible	= "microchip,mcp2515",
1266 		.data		= (void *)CAN_MCP251X_MCP2515,
1267 	},
1268 	{
1269 		.compatible	= "microchip,mcp25625",
1270 		.data		= (void *)CAN_MCP251X_MCP25625,
1271 	},
1272 	{ }
1273 };
1274 MODULE_DEVICE_TABLE(of, mcp251x_of_match);
1275 
1276 static const struct spi_device_id mcp251x_id_table[] = {
1277 	{
1278 		.name		= "mcp2510",
1279 		.driver_data	= (kernel_ulong_t)CAN_MCP251X_MCP2510,
1280 	},
1281 	{
1282 		.name		= "mcp2515",
1283 		.driver_data	= (kernel_ulong_t)CAN_MCP251X_MCP2515,
1284 	},
1285 	{
1286 		.name		= "mcp25625",
1287 		.driver_data	= (kernel_ulong_t)CAN_MCP251X_MCP25625,
1288 	},
1289 	{ }
1290 };
1291 MODULE_DEVICE_TABLE(spi, mcp251x_id_table);
1292 
1293 static int mcp251x_can_probe(struct spi_device *spi)
1294 {
1295 	const void *match = device_get_match_data(&spi->dev);
1296 	struct net_device *net;
1297 	struct mcp251x_priv *priv;
1298 	struct clk *clk;
1299 	u32 freq;
1300 	int ret;
1301 
1302 	clk = devm_clk_get_optional(&spi->dev, NULL);
1303 	if (IS_ERR(clk))
1304 		return PTR_ERR(clk);
1305 
1306 	freq = clk_get_rate(clk);
1307 	if (freq == 0)
1308 		device_property_read_u32(&spi->dev, "clock-frequency", &freq);
1309 
1310 	/* Sanity check */
1311 	if (freq < 1000000 || freq > 25000000)
1312 		return -ERANGE;
1313 
1314 	/* Allocate can/net device */
1315 	net = alloc_candev(sizeof(struct mcp251x_priv), TX_ECHO_SKB_MAX);
1316 	if (!net)
1317 		return -ENOMEM;
1318 
1319 	ret = clk_prepare_enable(clk);
1320 	if (ret)
1321 		goto out_free;
1322 
1323 	net->netdev_ops = &mcp251x_netdev_ops;
1324 	net->flags |= IFF_ECHO;
1325 
1326 	priv = netdev_priv(net);
1327 	priv->can.bittiming_const = &mcp251x_bittiming_const;
1328 	priv->can.do_set_mode = mcp251x_do_set_mode;
1329 	priv->can.clock.freq = freq / 2;
1330 	priv->can.ctrlmode_supported = CAN_CTRLMODE_3_SAMPLES |
1331 		CAN_CTRLMODE_LOOPBACK | CAN_CTRLMODE_LISTENONLY;
1332 	if (match)
1333 		priv->model = (enum mcp251x_model)(uintptr_t)match;
1334 	else
1335 		priv->model = spi_get_device_id(spi)->driver_data;
1336 	priv->net = net;
1337 	priv->clk = clk;
1338 
1339 	spi_set_drvdata(spi, priv);
1340 
1341 	/* Configure the SPI bus */
1342 	spi->bits_per_word = 8;
1343 	if (mcp251x_is_2510(spi))
1344 		spi->max_speed_hz = spi->max_speed_hz ? : 5 * 1000 * 1000;
1345 	else
1346 		spi->max_speed_hz = spi->max_speed_hz ? : 10 * 1000 * 1000;
1347 	ret = spi_setup(spi);
1348 	if (ret)
1349 		goto out_clk;
1350 
1351 	priv->power = devm_regulator_get_optional(&spi->dev, "vdd");
1352 	priv->transceiver = devm_regulator_get_optional(&spi->dev, "xceiver");
1353 	if ((PTR_ERR(priv->power) == -EPROBE_DEFER) ||
1354 	    (PTR_ERR(priv->transceiver) == -EPROBE_DEFER)) {
1355 		ret = -EPROBE_DEFER;
1356 		goto out_clk;
1357 	}
1358 
1359 	ret = mcp251x_power_enable(priv->power, 1);
1360 	if (ret)
1361 		goto out_clk;
1362 
1363 	priv->wq = alloc_workqueue("mcp251x_wq", WQ_FREEZABLE | WQ_MEM_RECLAIM,
1364 				   0);
1365 	if (!priv->wq) {
1366 		ret = -ENOMEM;
1367 		goto out_clk;
1368 	}
1369 	INIT_WORK(&priv->tx_work, mcp251x_tx_work_handler);
1370 	INIT_WORK(&priv->restart_work, mcp251x_restart_work_handler);
1371 
1372 	priv->spi = spi;
1373 	mutex_init(&priv->mcp_lock);
1374 
1375 	priv->spi_tx_buf = devm_kzalloc(&spi->dev, SPI_TRANSFER_BUF_LEN,
1376 					GFP_KERNEL);
1377 	if (!priv->spi_tx_buf) {
1378 		ret = -ENOMEM;
1379 		goto error_probe;
1380 	}
1381 
1382 	priv->spi_rx_buf = devm_kzalloc(&spi->dev, SPI_TRANSFER_BUF_LEN,
1383 					GFP_KERNEL);
1384 	if (!priv->spi_rx_buf) {
1385 		ret = -ENOMEM;
1386 		goto error_probe;
1387 	}
1388 
1389 	SET_NETDEV_DEV(net, &spi->dev);
1390 
1391 	/* Here is OK to not lock the MCP, no one knows about it yet */
1392 	ret = mcp251x_hw_probe(spi);
1393 	if (ret) {
1394 		if (ret == -ENODEV)
1395 			dev_err(&spi->dev, "Cannot initialize MCP%x. Wrong wiring?\n",
1396 				priv->model);
1397 		goto error_probe;
1398 	}
1399 
1400 	mcp251x_hw_sleep(spi);
1401 
1402 	ret = register_candev(net);
1403 	if (ret)
1404 		goto error_probe;
1405 
1406 	devm_can_led_init(net);
1407 
1408 	ret = mcp251x_gpio_setup(priv);
1409 	if (ret)
1410 		goto error_probe;
1411 
1412 	netdev_info(net, "MCP%x successfully initialized.\n", priv->model);
1413 	return 0;
1414 
1415 error_probe:
1416 	destroy_workqueue(priv->wq);
1417 	priv->wq = NULL;
1418 	mcp251x_power_enable(priv->power, 0);
1419 
1420 out_clk:
1421 	clk_disable_unprepare(clk);
1422 
1423 out_free:
1424 	free_candev(net);
1425 
1426 	dev_err(&spi->dev, "Probe failed, err=%d\n", -ret);
1427 	return ret;
1428 }
1429 
1430 static int mcp251x_can_remove(struct spi_device *spi)
1431 {
1432 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
1433 	struct net_device *net = priv->net;
1434 
1435 	unregister_candev(net);
1436 
1437 	mcp251x_power_enable(priv->power, 0);
1438 
1439 	destroy_workqueue(priv->wq);
1440 	priv->wq = NULL;
1441 
1442 	clk_disable_unprepare(priv->clk);
1443 
1444 	free_candev(net);
1445 
1446 	return 0;
1447 }
1448 
1449 static int __maybe_unused mcp251x_can_suspend(struct device *dev)
1450 {
1451 	struct spi_device *spi = to_spi_device(dev);
1452 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
1453 	struct net_device *net = priv->net;
1454 
1455 	priv->force_quit = 1;
1456 	disable_irq(spi->irq);
1457 	/* Note: at this point neither IST nor workqueues are running.
1458 	 * open/stop cannot be called anyway so locking is not needed
1459 	 */
1460 	if (netif_running(net)) {
1461 		netif_device_detach(net);
1462 
1463 		mcp251x_hw_sleep(spi);
1464 		mcp251x_power_enable(priv->transceiver, 0);
1465 		priv->after_suspend = AFTER_SUSPEND_UP;
1466 	} else {
1467 		priv->after_suspend = AFTER_SUSPEND_DOWN;
1468 	}
1469 
1470 	mcp251x_power_enable(priv->power, 0);
1471 	priv->after_suspend |= AFTER_SUSPEND_POWER;
1472 
1473 	return 0;
1474 }
1475 
1476 static int __maybe_unused mcp251x_can_resume(struct device *dev)
1477 {
1478 	struct spi_device *spi = to_spi_device(dev);
1479 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
1480 
1481 	if (priv->after_suspend & AFTER_SUSPEND_POWER)
1482 		mcp251x_power_enable(priv->power, 1);
1483 	if (priv->after_suspend & AFTER_SUSPEND_UP)
1484 		mcp251x_power_enable(priv->transceiver, 1);
1485 
1486 	if (priv->after_suspend & (AFTER_SUSPEND_POWER | AFTER_SUSPEND_UP))
1487 		queue_work(priv->wq, &priv->restart_work);
1488 	else
1489 		priv->after_suspend = 0;
1490 
1491 	priv->force_quit = 0;
1492 	enable_irq(spi->irq);
1493 	return 0;
1494 }
1495 
1496 static SIMPLE_DEV_PM_OPS(mcp251x_can_pm_ops, mcp251x_can_suspend,
1497 	mcp251x_can_resume);
1498 
1499 static struct spi_driver mcp251x_can_driver = {
1500 	.driver = {
1501 		.name = DEVICE_NAME,
1502 		.of_match_table = mcp251x_of_match,
1503 		.pm = &mcp251x_can_pm_ops,
1504 	},
1505 	.id_table = mcp251x_id_table,
1506 	.probe = mcp251x_can_probe,
1507 	.remove = mcp251x_can_remove,
1508 };
1509 module_spi_driver(mcp251x_can_driver);
1510 
1511 MODULE_AUTHOR("Chris Elston <celston@katalix.com>, "
1512 	      "Christian Pellegrin <chripell@evolware.org>");
1513 MODULE_DESCRIPTION("Microchip 251x/25625 CAN driver");
1514 MODULE_LICENSE("GPL v2");
1515