xref: /openbmc/linux/drivers/net/can/spi/hi311x.c (revision ee7da21a)
1 // SPDX-License-Identifier: GPL-2.0-only
2 /* CAN bus driver for Holt HI3110 CAN Controller with SPI Interface
3  *
4  * Copyright(C) Timesys Corporation 2016
5  *
6  * Based on Microchip 251x CAN Controller (mcp251x) Linux kernel driver
7  * Copyright 2009 Christian Pellegrin EVOL S.r.l.
8  * Copyright 2007 Raymarine UK, Ltd. All Rights Reserved.
9  * Copyright 2006 Arcom Control Systems Ltd.
10  *
11  * Based on CAN bus driver for the CCAN controller written by
12  * - Sascha Hauer, Marc Kleine-Budde, Pengutronix
13  * - Simon Kallweit, intefo AG
14  * Copyright 2007
15  */
16 
17 #include <linux/can/core.h>
18 #include <linux/can/dev.h>
19 #include <linux/can/led.h>
20 #include <linux/clk.h>
21 #include <linux/completion.h>
22 #include <linux/delay.h>
23 #include <linux/device.h>
24 #include <linux/freezer.h>
25 #include <linux/interrupt.h>
26 #include <linux/io.h>
27 #include <linux/kernel.h>
28 #include <linux/module.h>
29 #include <linux/netdevice.h>
30 #include <linux/of.h>
31 #include <linux/of_device.h>
32 #include <linux/platform_device.h>
33 #include <linux/regulator/consumer.h>
34 #include <linux/slab.h>
35 #include <linux/spi/spi.h>
36 #include <linux/uaccess.h>
37 
38 #define HI3110_MASTER_RESET 0x56
39 #define HI3110_READ_CTRL0 0xD2
40 #define HI3110_READ_CTRL1 0xD4
41 #define HI3110_READ_STATF 0xE2
42 #define HI3110_WRITE_CTRL0 0x14
43 #define HI3110_WRITE_CTRL1 0x16
44 #define HI3110_WRITE_INTE 0x1C
45 #define HI3110_WRITE_BTR0 0x18
46 #define HI3110_WRITE_BTR1 0x1A
47 #define HI3110_READ_BTR0 0xD6
48 #define HI3110_READ_BTR1 0xD8
49 #define HI3110_READ_INTF 0xDE
50 #define HI3110_READ_ERR 0xDC
51 #define HI3110_READ_FIFO_WOTIME 0x48
52 #define HI3110_WRITE_FIFO 0x12
53 #define HI3110_READ_MESSTAT 0xDA
54 #define HI3110_READ_REC 0xEA
55 #define HI3110_READ_TEC 0xEC
56 
57 #define HI3110_CTRL0_MODE_MASK (7 << 5)
58 #define HI3110_CTRL0_NORMAL_MODE (0 << 5)
59 #define HI3110_CTRL0_LOOPBACK_MODE (1 << 5)
60 #define HI3110_CTRL0_MONITOR_MODE (2 << 5)
61 #define HI3110_CTRL0_SLEEP_MODE (3 << 5)
62 #define HI3110_CTRL0_INIT_MODE (4 << 5)
63 
64 #define HI3110_CTRL1_TXEN BIT(7)
65 
66 #define HI3110_INT_RXTMP BIT(7)
67 #define HI3110_INT_RXFIFO BIT(6)
68 #define HI3110_INT_TXCPLT BIT(5)
69 #define HI3110_INT_BUSERR BIT(4)
70 #define HI3110_INT_MCHG BIT(3)
71 #define HI3110_INT_WAKEUP BIT(2)
72 #define HI3110_INT_F1MESS BIT(1)
73 #define HI3110_INT_F0MESS BIT(0)
74 
75 #define HI3110_ERR_BUSOFF BIT(7)
76 #define HI3110_ERR_TXERRP BIT(6)
77 #define HI3110_ERR_RXERRP BIT(5)
78 #define HI3110_ERR_BITERR BIT(4)
79 #define HI3110_ERR_FRMERR BIT(3)
80 #define HI3110_ERR_CRCERR BIT(2)
81 #define HI3110_ERR_ACKERR BIT(1)
82 #define HI3110_ERR_STUFERR BIT(0)
83 #define HI3110_ERR_PROTOCOL_MASK (0x1F)
84 #define HI3110_ERR_PASSIVE_MASK (0x60)
85 
86 #define HI3110_STAT_RXFMTY BIT(1)
87 #define HI3110_STAT_BUSOFF BIT(2)
88 #define HI3110_STAT_ERRP BIT(3)
89 #define HI3110_STAT_ERRW BIT(4)
90 #define HI3110_STAT_TXMTY BIT(7)
91 
92 #define HI3110_BTR0_SJW_SHIFT 6
93 #define HI3110_BTR0_BRP_SHIFT 0
94 
95 #define HI3110_BTR1_SAMP_3PERBIT (1 << 7)
96 #define HI3110_BTR1_SAMP_1PERBIT (0 << 7)
97 #define HI3110_BTR1_TSEG2_SHIFT 4
98 #define HI3110_BTR1_TSEG1_SHIFT 0
99 
100 #define HI3110_FIFO_WOTIME_TAG_OFF 0
101 #define HI3110_FIFO_WOTIME_ID_OFF 1
102 #define HI3110_FIFO_WOTIME_DLC_OFF 5
103 #define HI3110_FIFO_WOTIME_DAT_OFF 6
104 
105 #define HI3110_FIFO_WOTIME_TAG_IDE BIT(7)
106 #define HI3110_FIFO_WOTIME_ID_RTR BIT(0)
107 
108 #define HI3110_FIFO_TAG_OFF 0
109 #define HI3110_FIFO_ID_OFF 1
110 #define HI3110_FIFO_STD_DLC_OFF 3
111 #define HI3110_FIFO_STD_DATA_OFF 4
112 #define HI3110_FIFO_EXT_DLC_OFF 5
113 #define HI3110_FIFO_EXT_DATA_OFF 6
114 
115 #define HI3110_CAN_MAX_DATA_LEN 8
116 #define HI3110_RX_BUF_LEN 15
117 #define HI3110_TX_STD_BUF_LEN 12
118 #define HI3110_TX_EXT_BUF_LEN 14
119 #define HI3110_CAN_FRAME_MAX_BITS 128
120 #define HI3110_EFF_FLAGS 0x18 /* IDE + SRR */
121 
122 #define HI3110_TX_ECHO_SKB_MAX 1
123 
124 #define HI3110_OST_DELAY_MS (10)
125 
126 #define DEVICE_NAME "hi3110"
127 
128 static const struct can_bittiming_const hi3110_bittiming_const = {
129 	.name = DEVICE_NAME,
130 	.tseg1_min = 2,
131 	.tseg1_max = 16,
132 	.tseg2_min = 2,
133 	.tseg2_max = 8,
134 	.sjw_max = 4,
135 	.brp_min = 1,
136 	.brp_max = 64,
137 	.brp_inc = 1,
138 };
139 
140 enum hi3110_model {
141 	CAN_HI3110_HI3110 = 0x3110,
142 };
143 
144 struct hi3110_priv {
145 	struct can_priv can;
146 	struct net_device *net;
147 	struct spi_device *spi;
148 	enum hi3110_model model;
149 
150 	struct mutex hi3110_lock; /* SPI device lock */
151 
152 	u8 *spi_tx_buf;
153 	u8 *spi_rx_buf;
154 
155 	struct sk_buff *tx_skb;
156 	int tx_len;
157 
158 	struct workqueue_struct *wq;
159 	struct work_struct tx_work;
160 	struct work_struct restart_work;
161 
162 	int force_quit;
163 	int after_suspend;
164 #define HI3110_AFTER_SUSPEND_UP 1
165 #define HI3110_AFTER_SUSPEND_DOWN 2
166 #define HI3110_AFTER_SUSPEND_POWER 4
167 #define HI3110_AFTER_SUSPEND_RESTART 8
168 	int restart_tx;
169 	struct regulator *power;
170 	struct regulator *transceiver;
171 	struct clk *clk;
172 };
173 
174 static void hi3110_clean(struct net_device *net)
175 {
176 	struct hi3110_priv *priv = netdev_priv(net);
177 
178 	if (priv->tx_skb || priv->tx_len)
179 		net->stats.tx_errors++;
180 	dev_kfree_skb(priv->tx_skb);
181 	if (priv->tx_len)
182 		can_free_echo_skb(priv->net, 0, NULL);
183 	priv->tx_skb = NULL;
184 	priv->tx_len = 0;
185 }
186 
187 /* Note about handling of error return of hi3110_spi_trans: accessing
188  * registers via SPI is not really different conceptually than using
189  * normal I/O assembler instructions, although it's much more
190  * complicated from a practical POV. So it's not advisable to always
191  * check the return value of this function. Imagine that every
192  * read{b,l}, write{b,l} and friends would be bracketed in "if ( < 0)
193  * error();", it would be a great mess (well there are some situation
194  * when exception handling C++ like could be useful after all). So we
195  * just check that transfers are OK at the beginning of our
196  * conversation with the chip and to avoid doing really nasty things
197  * (like injecting bogus packets in the network stack).
198  */
199 static int hi3110_spi_trans(struct spi_device *spi, int len)
200 {
201 	struct hi3110_priv *priv = spi_get_drvdata(spi);
202 	struct spi_transfer t = {
203 		.tx_buf = priv->spi_tx_buf,
204 		.rx_buf = priv->spi_rx_buf,
205 		.len = len,
206 		.cs_change = 0,
207 	};
208 	struct spi_message m;
209 	int ret;
210 
211 	spi_message_init(&m);
212 	spi_message_add_tail(&t, &m);
213 
214 	ret = spi_sync(spi, &m);
215 
216 	if (ret)
217 		dev_err(&spi->dev, "spi transfer failed: ret = %d\n", ret);
218 	return ret;
219 }
220 
221 static int hi3110_cmd(struct spi_device *spi, u8 command)
222 {
223 	struct hi3110_priv *priv = spi_get_drvdata(spi);
224 
225 	priv->spi_tx_buf[0] = command;
226 	dev_dbg(&spi->dev, "hi3110_cmd: %02X\n", command);
227 
228 	return hi3110_spi_trans(spi, 1);
229 }
230 
231 static u8 hi3110_read(struct spi_device *spi, u8 command)
232 {
233 	struct hi3110_priv *priv = spi_get_drvdata(spi);
234 	u8 val = 0;
235 
236 	priv->spi_tx_buf[0] = command;
237 	hi3110_spi_trans(spi, 2);
238 	val = priv->spi_rx_buf[1];
239 
240 	return val;
241 }
242 
243 static void hi3110_write(struct spi_device *spi, u8 reg, u8 val)
244 {
245 	struct hi3110_priv *priv = spi_get_drvdata(spi);
246 
247 	priv->spi_tx_buf[0] = reg;
248 	priv->spi_tx_buf[1] = val;
249 	hi3110_spi_trans(spi, 2);
250 }
251 
252 static void hi3110_hw_tx_frame(struct spi_device *spi, u8 *buf, int len)
253 {
254 	struct hi3110_priv *priv = spi_get_drvdata(spi);
255 
256 	priv->spi_tx_buf[0] = HI3110_WRITE_FIFO;
257 	memcpy(priv->spi_tx_buf + 1, buf, len);
258 	hi3110_spi_trans(spi, len + 1);
259 }
260 
261 static void hi3110_hw_tx(struct spi_device *spi, struct can_frame *frame)
262 {
263 	u8 buf[HI3110_TX_EXT_BUF_LEN];
264 
265 	buf[HI3110_FIFO_TAG_OFF] = 0;
266 
267 	if (frame->can_id & CAN_EFF_FLAG) {
268 		/* Extended frame */
269 		buf[HI3110_FIFO_ID_OFF] = (frame->can_id & CAN_EFF_MASK) >> 21;
270 		buf[HI3110_FIFO_ID_OFF + 1] =
271 			(((frame->can_id & CAN_EFF_MASK) >> 13) & 0xe0) |
272 			HI3110_EFF_FLAGS |
273 			(((frame->can_id & CAN_EFF_MASK) >> 15) & 0x07);
274 		buf[HI3110_FIFO_ID_OFF + 2] =
275 			(frame->can_id & CAN_EFF_MASK) >> 7;
276 		buf[HI3110_FIFO_ID_OFF + 3] =
277 			((frame->can_id & CAN_EFF_MASK) << 1) |
278 			((frame->can_id & CAN_RTR_FLAG) ? 1 : 0);
279 
280 		buf[HI3110_FIFO_EXT_DLC_OFF] = frame->len;
281 
282 		memcpy(buf + HI3110_FIFO_EXT_DATA_OFF,
283 		       frame->data, frame->len);
284 
285 		hi3110_hw_tx_frame(spi, buf, HI3110_TX_EXT_BUF_LEN -
286 				   (HI3110_CAN_MAX_DATA_LEN - frame->len));
287 	} else {
288 		/* Standard frame */
289 		buf[HI3110_FIFO_ID_OFF] =   (frame->can_id & CAN_SFF_MASK) >> 3;
290 		buf[HI3110_FIFO_ID_OFF + 1] =
291 			((frame->can_id & CAN_SFF_MASK) << 5) |
292 			((frame->can_id & CAN_RTR_FLAG) ? (1 << 4) : 0);
293 
294 		buf[HI3110_FIFO_STD_DLC_OFF] = frame->len;
295 
296 		memcpy(buf + HI3110_FIFO_STD_DATA_OFF,
297 		       frame->data, frame->len);
298 
299 		hi3110_hw_tx_frame(spi, buf, HI3110_TX_STD_BUF_LEN -
300 				   (HI3110_CAN_MAX_DATA_LEN - frame->len));
301 	}
302 }
303 
304 static void hi3110_hw_rx_frame(struct spi_device *spi, u8 *buf)
305 {
306 	struct hi3110_priv *priv = spi_get_drvdata(spi);
307 
308 	priv->spi_tx_buf[0] = HI3110_READ_FIFO_WOTIME;
309 	hi3110_spi_trans(spi, HI3110_RX_BUF_LEN);
310 	memcpy(buf, priv->spi_rx_buf + 1, HI3110_RX_BUF_LEN - 1);
311 }
312 
313 static void hi3110_hw_rx(struct spi_device *spi)
314 {
315 	struct hi3110_priv *priv = spi_get_drvdata(spi);
316 	struct sk_buff *skb;
317 	struct can_frame *frame;
318 	u8 buf[HI3110_RX_BUF_LEN - 1];
319 
320 	skb = alloc_can_skb(priv->net, &frame);
321 	if (!skb) {
322 		priv->net->stats.rx_dropped++;
323 		return;
324 	}
325 
326 	hi3110_hw_rx_frame(spi, buf);
327 	if (buf[HI3110_FIFO_WOTIME_TAG_OFF] & HI3110_FIFO_WOTIME_TAG_IDE) {
328 		/* IDE is recessive (1), indicating extended 29-bit frame */
329 		frame->can_id = CAN_EFF_FLAG;
330 		frame->can_id |=
331 			(buf[HI3110_FIFO_WOTIME_ID_OFF] << 21) |
332 			(((buf[HI3110_FIFO_WOTIME_ID_OFF + 1] & 0xE0) >> 5) << 18) |
333 			((buf[HI3110_FIFO_WOTIME_ID_OFF + 1] & 0x07) << 15) |
334 			(buf[HI3110_FIFO_WOTIME_ID_OFF + 2] << 7) |
335 			(buf[HI3110_FIFO_WOTIME_ID_OFF + 3] >> 1);
336 	} else {
337 		/* IDE is dominant (0), frame indicating standard 11-bit */
338 		frame->can_id =
339 			(buf[HI3110_FIFO_WOTIME_ID_OFF] << 3) |
340 			((buf[HI3110_FIFO_WOTIME_ID_OFF + 1] & 0xE0) >> 5);
341 	}
342 
343 	/* Data length */
344 	frame->len = can_cc_dlc2len(buf[HI3110_FIFO_WOTIME_DLC_OFF] & 0x0F);
345 
346 	if (buf[HI3110_FIFO_WOTIME_ID_OFF + 3] & HI3110_FIFO_WOTIME_ID_RTR)
347 		frame->can_id |= CAN_RTR_FLAG;
348 	else
349 		memcpy(frame->data, buf + HI3110_FIFO_WOTIME_DAT_OFF,
350 		       frame->len);
351 
352 	priv->net->stats.rx_packets++;
353 	priv->net->stats.rx_bytes += frame->len;
354 
355 	can_led_event(priv->net, CAN_LED_EVENT_RX);
356 
357 	netif_rx_ni(skb);
358 }
359 
360 static void hi3110_hw_sleep(struct spi_device *spi)
361 {
362 	hi3110_write(spi, HI3110_WRITE_CTRL0, HI3110_CTRL0_SLEEP_MODE);
363 }
364 
365 static netdev_tx_t hi3110_hard_start_xmit(struct sk_buff *skb,
366 					  struct net_device *net)
367 {
368 	struct hi3110_priv *priv = netdev_priv(net);
369 	struct spi_device *spi = priv->spi;
370 
371 	if (priv->tx_skb || priv->tx_len) {
372 		dev_err(&spi->dev, "hard_xmit called while tx busy\n");
373 		return NETDEV_TX_BUSY;
374 	}
375 
376 	if (can_dropped_invalid_skb(net, skb))
377 		return NETDEV_TX_OK;
378 
379 	netif_stop_queue(net);
380 	priv->tx_skb = skb;
381 	queue_work(priv->wq, &priv->tx_work);
382 
383 	return NETDEV_TX_OK;
384 }
385 
386 static int hi3110_do_set_mode(struct net_device *net, enum can_mode mode)
387 {
388 	struct hi3110_priv *priv = netdev_priv(net);
389 
390 	switch (mode) {
391 	case CAN_MODE_START:
392 		hi3110_clean(net);
393 		/* We have to delay work since SPI I/O may sleep */
394 		priv->can.state = CAN_STATE_ERROR_ACTIVE;
395 		priv->restart_tx = 1;
396 		if (priv->can.restart_ms == 0)
397 			priv->after_suspend = HI3110_AFTER_SUSPEND_RESTART;
398 		queue_work(priv->wq, &priv->restart_work);
399 		break;
400 	default:
401 		return -EOPNOTSUPP;
402 	}
403 
404 	return 0;
405 }
406 
407 static int hi3110_get_berr_counter(const struct net_device *net,
408 				   struct can_berr_counter *bec)
409 {
410 	struct hi3110_priv *priv = netdev_priv(net);
411 	struct spi_device *spi = priv->spi;
412 
413 	mutex_lock(&priv->hi3110_lock);
414 	bec->txerr = hi3110_read(spi, HI3110_READ_TEC);
415 	bec->rxerr = hi3110_read(spi, HI3110_READ_REC);
416 	mutex_unlock(&priv->hi3110_lock);
417 
418 	return 0;
419 }
420 
421 static int hi3110_set_normal_mode(struct spi_device *spi)
422 {
423 	struct hi3110_priv *priv = spi_get_drvdata(spi);
424 	u8 reg = 0;
425 
426 	hi3110_write(spi, HI3110_WRITE_INTE, HI3110_INT_BUSERR |
427 		     HI3110_INT_RXFIFO | HI3110_INT_TXCPLT);
428 
429 	/* Enable TX */
430 	hi3110_write(spi, HI3110_WRITE_CTRL1, HI3110_CTRL1_TXEN);
431 
432 	if (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK)
433 		reg = HI3110_CTRL0_LOOPBACK_MODE;
434 	else if (priv->can.ctrlmode & CAN_CTRLMODE_LISTENONLY)
435 		reg = HI3110_CTRL0_MONITOR_MODE;
436 	else
437 		reg = HI3110_CTRL0_NORMAL_MODE;
438 
439 	hi3110_write(spi, HI3110_WRITE_CTRL0, reg);
440 
441 	/* Wait for the device to enter the mode */
442 	mdelay(HI3110_OST_DELAY_MS);
443 	reg = hi3110_read(spi, HI3110_READ_CTRL0);
444 	if ((reg & HI3110_CTRL0_MODE_MASK) != reg)
445 		return -EBUSY;
446 
447 	priv->can.state = CAN_STATE_ERROR_ACTIVE;
448 	return 0;
449 }
450 
451 static int hi3110_do_set_bittiming(struct net_device *net)
452 {
453 	struct hi3110_priv *priv = netdev_priv(net);
454 	struct can_bittiming *bt = &priv->can.bittiming;
455 	struct spi_device *spi = priv->spi;
456 
457 	hi3110_write(spi, HI3110_WRITE_BTR0,
458 		     ((bt->sjw - 1) << HI3110_BTR0_SJW_SHIFT) |
459 		     ((bt->brp - 1) << HI3110_BTR0_BRP_SHIFT));
460 
461 	hi3110_write(spi, HI3110_WRITE_BTR1,
462 		     (priv->can.ctrlmode &
463 		      CAN_CTRLMODE_3_SAMPLES ?
464 		      HI3110_BTR1_SAMP_3PERBIT : HI3110_BTR1_SAMP_1PERBIT) |
465 		     ((bt->phase_seg1 + bt->prop_seg - 1)
466 		      << HI3110_BTR1_TSEG1_SHIFT) |
467 		     ((bt->phase_seg2 - 1) << HI3110_BTR1_TSEG2_SHIFT));
468 
469 	dev_dbg(&spi->dev, "BT: 0x%02x 0x%02x\n",
470 		hi3110_read(spi, HI3110_READ_BTR0),
471 		hi3110_read(spi, HI3110_READ_BTR1));
472 
473 	return 0;
474 }
475 
476 static int hi3110_setup(struct net_device *net)
477 {
478 	hi3110_do_set_bittiming(net);
479 	return 0;
480 }
481 
482 static int hi3110_hw_reset(struct spi_device *spi)
483 {
484 	u8 reg;
485 	int ret;
486 
487 	/* Wait for oscillator startup timer after power up */
488 	mdelay(HI3110_OST_DELAY_MS);
489 
490 	ret = hi3110_cmd(spi, HI3110_MASTER_RESET);
491 	if (ret)
492 		return ret;
493 
494 	/* Wait for oscillator startup timer after reset */
495 	mdelay(HI3110_OST_DELAY_MS);
496 
497 	reg = hi3110_read(spi, HI3110_READ_CTRL0);
498 	if ((reg & HI3110_CTRL0_MODE_MASK) != HI3110_CTRL0_INIT_MODE)
499 		return -ENODEV;
500 
501 	/* As per the datasheet it appears the error flags are
502 	 * not cleared on reset. Explicitly clear them by performing a read
503 	 */
504 	hi3110_read(spi, HI3110_READ_ERR);
505 
506 	return 0;
507 }
508 
509 static int hi3110_hw_probe(struct spi_device *spi)
510 {
511 	u8 statf;
512 
513 	hi3110_hw_reset(spi);
514 
515 	/* Confirm correct operation by checking against reset values
516 	 * in datasheet
517 	 */
518 	statf = hi3110_read(spi, HI3110_READ_STATF);
519 
520 	dev_dbg(&spi->dev, "statf: %02X\n", statf);
521 
522 	if (statf != 0x82)
523 		return -ENODEV;
524 
525 	return 0;
526 }
527 
528 static int hi3110_power_enable(struct regulator *reg, int enable)
529 {
530 	if (IS_ERR_OR_NULL(reg))
531 		return 0;
532 
533 	if (enable)
534 		return regulator_enable(reg);
535 	else
536 		return regulator_disable(reg);
537 }
538 
539 static int hi3110_stop(struct net_device *net)
540 {
541 	struct hi3110_priv *priv = netdev_priv(net);
542 	struct spi_device *spi = priv->spi;
543 
544 	close_candev(net);
545 
546 	priv->force_quit = 1;
547 	free_irq(spi->irq, priv);
548 	destroy_workqueue(priv->wq);
549 	priv->wq = NULL;
550 
551 	mutex_lock(&priv->hi3110_lock);
552 
553 	/* Disable transmit, interrupts and clear flags */
554 	hi3110_write(spi, HI3110_WRITE_CTRL1, 0x0);
555 	hi3110_write(spi, HI3110_WRITE_INTE, 0x0);
556 	hi3110_read(spi, HI3110_READ_INTF);
557 
558 	hi3110_clean(net);
559 
560 	hi3110_hw_sleep(spi);
561 
562 	hi3110_power_enable(priv->transceiver, 0);
563 
564 	priv->can.state = CAN_STATE_STOPPED;
565 
566 	mutex_unlock(&priv->hi3110_lock);
567 
568 	can_led_event(net, CAN_LED_EVENT_STOP);
569 
570 	return 0;
571 }
572 
573 static void hi3110_tx_work_handler(struct work_struct *ws)
574 {
575 	struct hi3110_priv *priv = container_of(ws, struct hi3110_priv,
576 						tx_work);
577 	struct spi_device *spi = priv->spi;
578 	struct net_device *net = priv->net;
579 	struct can_frame *frame;
580 
581 	mutex_lock(&priv->hi3110_lock);
582 	if (priv->tx_skb) {
583 		if (priv->can.state == CAN_STATE_BUS_OFF) {
584 			hi3110_clean(net);
585 		} else {
586 			frame = (struct can_frame *)priv->tx_skb->data;
587 			hi3110_hw_tx(spi, frame);
588 			priv->tx_len = 1 + frame->len;
589 			can_put_echo_skb(priv->tx_skb, net, 0, 0);
590 			priv->tx_skb = NULL;
591 		}
592 	}
593 	mutex_unlock(&priv->hi3110_lock);
594 }
595 
596 static void hi3110_restart_work_handler(struct work_struct *ws)
597 {
598 	struct hi3110_priv *priv = container_of(ws, struct hi3110_priv,
599 						restart_work);
600 	struct spi_device *spi = priv->spi;
601 	struct net_device *net = priv->net;
602 
603 	mutex_lock(&priv->hi3110_lock);
604 	if (priv->after_suspend) {
605 		hi3110_hw_reset(spi);
606 		hi3110_setup(net);
607 		if (priv->after_suspend & HI3110_AFTER_SUSPEND_RESTART) {
608 			hi3110_set_normal_mode(spi);
609 		} else if (priv->after_suspend & HI3110_AFTER_SUSPEND_UP) {
610 			netif_device_attach(net);
611 			hi3110_clean(net);
612 			hi3110_set_normal_mode(spi);
613 			netif_wake_queue(net);
614 		} else {
615 			hi3110_hw_sleep(spi);
616 		}
617 		priv->after_suspend = 0;
618 		priv->force_quit = 0;
619 	}
620 
621 	if (priv->restart_tx) {
622 		priv->restart_tx = 0;
623 		hi3110_hw_reset(spi);
624 		hi3110_setup(net);
625 		hi3110_clean(net);
626 		hi3110_set_normal_mode(spi);
627 		netif_wake_queue(net);
628 	}
629 	mutex_unlock(&priv->hi3110_lock);
630 }
631 
632 static irqreturn_t hi3110_can_ist(int irq, void *dev_id)
633 {
634 	struct hi3110_priv *priv = dev_id;
635 	struct spi_device *spi = priv->spi;
636 	struct net_device *net = priv->net;
637 
638 	mutex_lock(&priv->hi3110_lock);
639 
640 	while (!priv->force_quit) {
641 		enum can_state new_state;
642 		u8 intf, eflag, statf;
643 
644 		while (!(HI3110_STAT_RXFMTY &
645 			 (statf = hi3110_read(spi, HI3110_READ_STATF)))) {
646 			hi3110_hw_rx(spi);
647 		}
648 
649 		intf = hi3110_read(spi, HI3110_READ_INTF);
650 		eflag = hi3110_read(spi, HI3110_READ_ERR);
651 		/* Update can state */
652 		if (eflag & HI3110_ERR_BUSOFF)
653 			new_state = CAN_STATE_BUS_OFF;
654 		else if (eflag & HI3110_ERR_PASSIVE_MASK)
655 			new_state = CAN_STATE_ERROR_PASSIVE;
656 		else if (statf & HI3110_STAT_ERRW)
657 			new_state = CAN_STATE_ERROR_WARNING;
658 		else
659 			new_state = CAN_STATE_ERROR_ACTIVE;
660 
661 		if (new_state != priv->can.state) {
662 			struct can_frame *cf;
663 			struct sk_buff *skb;
664 			enum can_state rx_state, tx_state;
665 			u8 rxerr, txerr;
666 
667 			skb = alloc_can_err_skb(net, &cf);
668 			if (!skb)
669 				break;
670 
671 			txerr = hi3110_read(spi, HI3110_READ_TEC);
672 			rxerr = hi3110_read(spi, HI3110_READ_REC);
673 			cf->data[6] = txerr;
674 			cf->data[7] = rxerr;
675 			tx_state = txerr >= rxerr ? new_state : 0;
676 			rx_state = txerr <= rxerr ? new_state : 0;
677 			can_change_state(net, cf, tx_state, rx_state);
678 			netif_rx_ni(skb);
679 
680 			if (new_state == CAN_STATE_BUS_OFF) {
681 				can_bus_off(net);
682 				if (priv->can.restart_ms == 0) {
683 					priv->force_quit = 1;
684 					hi3110_hw_sleep(spi);
685 					break;
686 				}
687 			}
688 		}
689 
690 		/* Update bus errors */
691 		if ((intf & HI3110_INT_BUSERR) &&
692 		    (priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)) {
693 			struct can_frame *cf;
694 			struct sk_buff *skb;
695 
696 			/* Check for protocol errors */
697 			if (eflag & HI3110_ERR_PROTOCOL_MASK) {
698 				skb = alloc_can_err_skb(net, &cf);
699 				if (!skb)
700 					break;
701 
702 				cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
703 				priv->can.can_stats.bus_error++;
704 				priv->net->stats.rx_errors++;
705 				if (eflag & HI3110_ERR_BITERR)
706 					cf->data[2] |= CAN_ERR_PROT_BIT;
707 				else if (eflag & HI3110_ERR_FRMERR)
708 					cf->data[2] |= CAN_ERR_PROT_FORM;
709 				else if (eflag & HI3110_ERR_STUFERR)
710 					cf->data[2] |= CAN_ERR_PROT_STUFF;
711 				else if (eflag & HI3110_ERR_CRCERR)
712 					cf->data[3] |= CAN_ERR_PROT_LOC_CRC_SEQ;
713 				else if (eflag & HI3110_ERR_ACKERR)
714 					cf->data[3] |= CAN_ERR_PROT_LOC_ACK;
715 
716 				cf->data[6] = hi3110_read(spi, HI3110_READ_TEC);
717 				cf->data[7] = hi3110_read(spi, HI3110_READ_REC);
718 				netdev_dbg(priv->net, "Bus Error\n");
719 				netif_rx_ni(skb);
720 			}
721 		}
722 
723 		if (priv->tx_len && statf & HI3110_STAT_TXMTY) {
724 			net->stats.tx_packets++;
725 			net->stats.tx_bytes += priv->tx_len - 1;
726 			can_led_event(net, CAN_LED_EVENT_TX);
727 			if (priv->tx_len) {
728 				can_get_echo_skb(net, 0, NULL);
729 				priv->tx_len = 0;
730 			}
731 			netif_wake_queue(net);
732 		}
733 
734 		if (intf == 0)
735 			break;
736 	}
737 	mutex_unlock(&priv->hi3110_lock);
738 	return IRQ_HANDLED;
739 }
740 
741 static int hi3110_open(struct net_device *net)
742 {
743 	struct hi3110_priv *priv = netdev_priv(net);
744 	struct spi_device *spi = priv->spi;
745 	unsigned long flags = IRQF_ONESHOT | IRQF_TRIGGER_HIGH;
746 	int ret;
747 
748 	ret = open_candev(net);
749 	if (ret)
750 		return ret;
751 
752 	mutex_lock(&priv->hi3110_lock);
753 	hi3110_power_enable(priv->transceiver, 1);
754 
755 	priv->force_quit = 0;
756 	priv->tx_skb = NULL;
757 	priv->tx_len = 0;
758 
759 	ret = request_threaded_irq(spi->irq, NULL, hi3110_can_ist,
760 				   flags, DEVICE_NAME, priv);
761 	if (ret) {
762 		dev_err(&spi->dev, "failed to acquire irq %d\n", spi->irq);
763 		goto out_close;
764 	}
765 
766 	priv->wq = alloc_workqueue("hi3110_wq", WQ_FREEZABLE | WQ_MEM_RECLAIM,
767 				   0);
768 	if (!priv->wq) {
769 		ret = -ENOMEM;
770 		goto out_free_irq;
771 	}
772 	INIT_WORK(&priv->tx_work, hi3110_tx_work_handler);
773 	INIT_WORK(&priv->restart_work, hi3110_restart_work_handler);
774 
775 	ret = hi3110_hw_reset(spi);
776 	if (ret)
777 		goto out_free_wq;
778 
779 	ret = hi3110_setup(net);
780 	if (ret)
781 		goto out_free_wq;
782 
783 	ret = hi3110_set_normal_mode(spi);
784 	if (ret)
785 		goto out_free_wq;
786 
787 	can_led_event(net, CAN_LED_EVENT_OPEN);
788 	netif_wake_queue(net);
789 	mutex_unlock(&priv->hi3110_lock);
790 
791 	return 0;
792 
793  out_free_wq:
794 	destroy_workqueue(priv->wq);
795  out_free_irq:
796 	free_irq(spi->irq, priv);
797 	hi3110_hw_sleep(spi);
798  out_close:
799 	hi3110_power_enable(priv->transceiver, 0);
800 	close_candev(net);
801 	mutex_unlock(&priv->hi3110_lock);
802 	return ret;
803 }
804 
805 static const struct net_device_ops hi3110_netdev_ops = {
806 	.ndo_open = hi3110_open,
807 	.ndo_stop = hi3110_stop,
808 	.ndo_start_xmit = hi3110_hard_start_xmit,
809 };
810 
811 static const struct of_device_id hi3110_of_match[] = {
812 	{
813 		.compatible	= "holt,hi3110",
814 		.data		= (void *)CAN_HI3110_HI3110,
815 	},
816 	{ }
817 };
818 MODULE_DEVICE_TABLE(of, hi3110_of_match);
819 
820 static const struct spi_device_id hi3110_id_table[] = {
821 	{
822 		.name		= "hi3110",
823 		.driver_data	= (kernel_ulong_t)CAN_HI3110_HI3110,
824 	},
825 	{ }
826 };
827 MODULE_DEVICE_TABLE(spi, hi3110_id_table);
828 
829 static int hi3110_can_probe(struct spi_device *spi)
830 {
831 	const struct of_device_id *of_id = of_match_device(hi3110_of_match,
832 							   &spi->dev);
833 	struct net_device *net;
834 	struct hi3110_priv *priv;
835 	struct clk *clk;
836 	int freq, ret;
837 
838 	clk = devm_clk_get(&spi->dev, NULL);
839 	if (IS_ERR(clk)) {
840 		dev_err(&spi->dev, "no CAN clock source defined\n");
841 		return PTR_ERR(clk);
842 	}
843 	freq = clk_get_rate(clk);
844 
845 	/* Sanity check */
846 	if (freq > 40000000)
847 		return -ERANGE;
848 
849 	/* Allocate can/net device */
850 	net = alloc_candev(sizeof(struct hi3110_priv), HI3110_TX_ECHO_SKB_MAX);
851 	if (!net)
852 		return -ENOMEM;
853 
854 	if (!IS_ERR(clk)) {
855 		ret = clk_prepare_enable(clk);
856 		if (ret)
857 			goto out_free;
858 	}
859 
860 	net->netdev_ops = &hi3110_netdev_ops;
861 	net->flags |= IFF_ECHO;
862 
863 	priv = netdev_priv(net);
864 	priv->can.bittiming_const = &hi3110_bittiming_const;
865 	priv->can.do_set_mode = hi3110_do_set_mode;
866 	priv->can.do_get_berr_counter = hi3110_get_berr_counter;
867 	priv->can.clock.freq = freq / 2;
868 	priv->can.ctrlmode_supported = CAN_CTRLMODE_3_SAMPLES |
869 		CAN_CTRLMODE_LOOPBACK |
870 		CAN_CTRLMODE_LISTENONLY |
871 		CAN_CTRLMODE_BERR_REPORTING;
872 
873 	if (of_id)
874 		priv->model = (enum hi3110_model)(uintptr_t)of_id->data;
875 	else
876 		priv->model = spi_get_device_id(spi)->driver_data;
877 	priv->net = net;
878 	priv->clk = clk;
879 
880 	spi_set_drvdata(spi, priv);
881 
882 	/* Configure the SPI bus */
883 	spi->bits_per_word = 8;
884 	ret = spi_setup(spi);
885 	if (ret)
886 		goto out_clk;
887 
888 	priv->power = devm_regulator_get_optional(&spi->dev, "vdd");
889 	priv->transceiver = devm_regulator_get_optional(&spi->dev, "xceiver");
890 	if ((PTR_ERR(priv->power) == -EPROBE_DEFER) ||
891 	    (PTR_ERR(priv->transceiver) == -EPROBE_DEFER)) {
892 		ret = -EPROBE_DEFER;
893 		goto out_clk;
894 	}
895 
896 	ret = hi3110_power_enable(priv->power, 1);
897 	if (ret)
898 		goto out_clk;
899 
900 	priv->spi = spi;
901 	mutex_init(&priv->hi3110_lock);
902 
903 	priv->spi_tx_buf = devm_kzalloc(&spi->dev, HI3110_RX_BUF_LEN,
904 					GFP_KERNEL);
905 	if (!priv->spi_tx_buf) {
906 		ret = -ENOMEM;
907 		goto error_probe;
908 	}
909 	priv->spi_rx_buf = devm_kzalloc(&spi->dev, HI3110_RX_BUF_LEN,
910 					GFP_KERNEL);
911 
912 	if (!priv->spi_rx_buf) {
913 		ret = -ENOMEM;
914 		goto error_probe;
915 	}
916 
917 	SET_NETDEV_DEV(net, &spi->dev);
918 
919 	ret = hi3110_hw_probe(spi);
920 	if (ret) {
921 		if (ret == -ENODEV)
922 			dev_err(&spi->dev, "Cannot initialize %x. Wrong wiring?\n",
923 				priv->model);
924 		goto error_probe;
925 	}
926 	hi3110_hw_sleep(spi);
927 
928 	ret = register_candev(net);
929 	if (ret)
930 		goto error_probe;
931 
932 	devm_can_led_init(net);
933 	netdev_info(net, "%x successfully initialized.\n", priv->model);
934 
935 	return 0;
936 
937  error_probe:
938 	hi3110_power_enable(priv->power, 0);
939 
940  out_clk:
941 	if (!IS_ERR(clk))
942 		clk_disable_unprepare(clk);
943 
944  out_free:
945 	free_candev(net);
946 
947 	dev_err(&spi->dev, "Probe failed, err=%d\n", -ret);
948 	return ret;
949 }
950 
951 static int hi3110_can_remove(struct spi_device *spi)
952 {
953 	struct hi3110_priv *priv = spi_get_drvdata(spi);
954 	struct net_device *net = priv->net;
955 
956 	unregister_candev(net);
957 
958 	hi3110_power_enable(priv->power, 0);
959 
960 	if (!IS_ERR(priv->clk))
961 		clk_disable_unprepare(priv->clk);
962 
963 	free_candev(net);
964 
965 	return 0;
966 }
967 
968 static int __maybe_unused hi3110_can_suspend(struct device *dev)
969 {
970 	struct spi_device *spi = to_spi_device(dev);
971 	struct hi3110_priv *priv = spi_get_drvdata(spi);
972 	struct net_device *net = priv->net;
973 
974 	priv->force_quit = 1;
975 	disable_irq(spi->irq);
976 
977 	/* Note: at this point neither IST nor workqueues are running.
978 	 * open/stop cannot be called anyway so locking is not needed
979 	 */
980 	if (netif_running(net)) {
981 		netif_device_detach(net);
982 
983 		hi3110_hw_sleep(spi);
984 		hi3110_power_enable(priv->transceiver, 0);
985 		priv->after_suspend = HI3110_AFTER_SUSPEND_UP;
986 	} else {
987 		priv->after_suspend = HI3110_AFTER_SUSPEND_DOWN;
988 	}
989 
990 	if (!IS_ERR_OR_NULL(priv->power)) {
991 		regulator_disable(priv->power);
992 		priv->after_suspend |= HI3110_AFTER_SUSPEND_POWER;
993 	}
994 
995 	return 0;
996 }
997 
998 static int __maybe_unused hi3110_can_resume(struct device *dev)
999 {
1000 	struct spi_device *spi = to_spi_device(dev);
1001 	struct hi3110_priv *priv = spi_get_drvdata(spi);
1002 
1003 	if (priv->after_suspend & HI3110_AFTER_SUSPEND_POWER)
1004 		hi3110_power_enable(priv->power, 1);
1005 
1006 	if (priv->after_suspend & HI3110_AFTER_SUSPEND_UP) {
1007 		hi3110_power_enable(priv->transceiver, 1);
1008 		queue_work(priv->wq, &priv->restart_work);
1009 	} else {
1010 		priv->after_suspend = 0;
1011 	}
1012 
1013 	priv->force_quit = 0;
1014 	enable_irq(spi->irq);
1015 	return 0;
1016 }
1017 
1018 static SIMPLE_DEV_PM_OPS(hi3110_can_pm_ops, hi3110_can_suspend, hi3110_can_resume);
1019 
1020 static struct spi_driver hi3110_can_driver = {
1021 	.driver = {
1022 		.name = DEVICE_NAME,
1023 		.of_match_table = hi3110_of_match,
1024 		.pm = &hi3110_can_pm_ops,
1025 	},
1026 	.id_table = hi3110_id_table,
1027 	.probe = hi3110_can_probe,
1028 	.remove = hi3110_can_remove,
1029 };
1030 
1031 module_spi_driver(hi3110_can_driver);
1032 
1033 MODULE_AUTHOR("Akshay Bhat <akshay.bhat@timesys.com>");
1034 MODULE_AUTHOR("Casey Fitzpatrick <casey.fitzpatrick@timesys.com>");
1035 MODULE_DESCRIPTION("Holt HI-3110 CAN driver");
1036 MODULE_LICENSE("GPL v2");
1037