1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright (C) 2007, 2011 Wolfgang Grandegger <wg@grandegger.com> 4 * Copyright (C) 2012 Stephane Grosjean <s.grosjean@peak-system.com> 5 * 6 * Derived from the PCAN project file driver/src/pcan_pci.c: 7 * 8 * Copyright (C) 2001-2006 PEAK System-Technik GmbH 9 */ 10 11 #include <linux/kernel.h> 12 #include <linux/module.h> 13 #include <linux/interrupt.h> 14 #include <linux/netdevice.h> 15 #include <linux/delay.h> 16 #include <linux/pci.h> 17 #include <linux/io.h> 18 #include <linux/can.h> 19 #include <linux/can/dev.h> 20 21 #include "peak_canfd_user.h" 22 23 MODULE_AUTHOR("Stephane Grosjean <s.grosjean@peak-system.com>"); 24 MODULE_DESCRIPTION("Socket-CAN driver for PEAK PCAN PCIe/M.2 FD family cards"); 25 MODULE_SUPPORTED_DEVICE("PEAK PCAN PCIe/M.2 FD CAN cards"); 26 MODULE_LICENSE("GPL v2"); 27 28 #define PCIEFD_DRV_NAME "peak_pciefd" 29 30 #define PEAK_PCI_VENDOR_ID 0x001c /* The PCI device and vendor IDs */ 31 #define PEAK_PCIEFD_ID 0x0013 /* for PCIe slot cards */ 32 #define PCAN_CPCIEFD_ID 0x0014 /* for Compact-PCI Serial slot cards */ 33 #define PCAN_PCIE104FD_ID 0x0017 /* for PCIe-104 Express slot cards */ 34 #define PCAN_MINIPCIEFD_ID 0x0018 /* for mini-PCIe slot cards */ 35 #define PCAN_PCIEFD_OEM_ID 0x0019 /* for PCIe slot OEM cards */ 36 #define PCAN_M2_ID 0x001a /* for M2 slot cards */ 37 38 /* PEAK PCIe board access description */ 39 #define PCIEFD_BAR0_SIZE (64 * 1024) 40 #define PCIEFD_RX_DMA_SIZE (4 * 1024) 41 #define PCIEFD_TX_DMA_SIZE (4 * 1024) 42 43 #define PCIEFD_TX_PAGE_SIZE (2 * 1024) 44 45 /* System Control Registers */ 46 #define PCIEFD_REG_SYS_CTL_SET 0x0000 /* set bits */ 47 #define PCIEFD_REG_SYS_CTL_CLR 0x0004 /* clear bits */ 48 49 /* Version info registers */ 50 #define PCIEFD_REG_SYS_VER1 0x0040 /* version reg #1 */ 51 #define PCIEFD_REG_SYS_VER2 0x0044 /* version reg #2 */ 52 53 #define PCIEFD_FW_VERSION(x, y, z) (((u32)(x) << 24) | \ 54 ((u32)(y) << 16) | \ 55 ((u32)(z) << 8)) 56 57 /* System Control Registers Bits */ 58 #define PCIEFD_SYS_CTL_TS_RST 0x00000001 /* timestamp clock */ 59 #define PCIEFD_SYS_CTL_CLK_EN 0x00000002 /* system clock */ 60 61 /* CAN-FD channel addresses */ 62 #define PCIEFD_CANX_OFF(c) (((c) + 1) * 0x1000) 63 64 #define PCIEFD_ECHO_SKB_MAX PCANFD_ECHO_SKB_DEF 65 66 /* CAN-FD channel registers */ 67 #define PCIEFD_REG_CAN_MISC 0x0000 /* Misc. control */ 68 #define PCIEFD_REG_CAN_CLK_SEL 0x0008 /* Clock selector */ 69 #define PCIEFD_REG_CAN_CMD_PORT_L 0x0010 /* 64-bits command port */ 70 #define PCIEFD_REG_CAN_CMD_PORT_H 0x0014 71 #define PCIEFD_REG_CAN_TX_REQ_ACC 0x0020 /* Tx request accumulator */ 72 #define PCIEFD_REG_CAN_TX_CTL_SET 0x0030 /* Tx control set register */ 73 #define PCIEFD_REG_CAN_TX_CTL_CLR 0x0038 /* Tx control clear register */ 74 #define PCIEFD_REG_CAN_TX_DMA_ADDR_L 0x0040 /* 64-bits addr for Tx DMA */ 75 #define PCIEFD_REG_CAN_TX_DMA_ADDR_H 0x0044 76 #define PCIEFD_REG_CAN_RX_CTL_SET 0x0050 /* Rx control set register */ 77 #define PCIEFD_REG_CAN_RX_CTL_CLR 0x0058 /* Rx control clear register */ 78 #define PCIEFD_REG_CAN_RX_CTL_WRT 0x0060 /* Rx control write register */ 79 #define PCIEFD_REG_CAN_RX_CTL_ACK 0x0068 /* Rx control ACK register */ 80 #define PCIEFD_REG_CAN_RX_DMA_ADDR_L 0x0070 /* 64-bits addr for Rx DMA */ 81 #define PCIEFD_REG_CAN_RX_DMA_ADDR_H 0x0074 82 83 /* CAN-FD channel misc register bits */ 84 #define CANFD_MISC_TS_RST 0x00000001 /* timestamp cnt rst */ 85 86 /* CAN-FD channel Clock SELector Source & DIVider */ 87 #define CANFD_CLK_SEL_DIV_MASK 0x00000007 88 #define CANFD_CLK_SEL_DIV_60MHZ 0x00000000 /* SRC=240MHz only */ 89 #define CANFD_CLK_SEL_DIV_40MHZ 0x00000001 /* SRC=240MHz only */ 90 #define CANFD_CLK_SEL_DIV_30MHZ 0x00000002 /* SRC=240MHz only */ 91 #define CANFD_CLK_SEL_DIV_24MHZ 0x00000003 /* SRC=240MHz only */ 92 #define CANFD_CLK_SEL_DIV_20MHZ 0x00000004 /* SRC=240MHz only */ 93 94 #define CANFD_CLK_SEL_SRC_MASK 0x00000008 /* 0=80MHz, 1=240MHz */ 95 #define CANFD_CLK_SEL_SRC_240MHZ 0x00000008 96 #define CANFD_CLK_SEL_SRC_80MHZ (~CANFD_CLK_SEL_SRC_240MHZ & \ 97 CANFD_CLK_SEL_SRC_MASK) 98 99 #define CANFD_CLK_SEL_20MHZ (CANFD_CLK_SEL_SRC_240MHZ |\ 100 CANFD_CLK_SEL_DIV_20MHZ) 101 #define CANFD_CLK_SEL_24MHZ (CANFD_CLK_SEL_SRC_240MHZ |\ 102 CANFD_CLK_SEL_DIV_24MHZ) 103 #define CANFD_CLK_SEL_30MHZ (CANFD_CLK_SEL_SRC_240MHZ |\ 104 CANFD_CLK_SEL_DIV_30MHZ) 105 #define CANFD_CLK_SEL_40MHZ (CANFD_CLK_SEL_SRC_240MHZ |\ 106 CANFD_CLK_SEL_DIV_40MHZ) 107 #define CANFD_CLK_SEL_60MHZ (CANFD_CLK_SEL_SRC_240MHZ |\ 108 CANFD_CLK_SEL_DIV_60MHZ) 109 #define CANFD_CLK_SEL_80MHZ (CANFD_CLK_SEL_SRC_80MHZ) 110 111 /* CAN-FD channel Rx/Tx control register bits */ 112 #define CANFD_CTL_UNC_BIT 0x00010000 /* Uncached DMA mem */ 113 #define CANFD_CTL_RST_BIT 0x00020000 /* reset DMA action */ 114 #define CANFD_CTL_IEN_BIT 0x00040000 /* IRQ enable */ 115 116 /* Rx IRQ Count and Time Limits */ 117 #define CANFD_CTL_IRQ_CL_DEF 16 /* Rx msg max nb per IRQ in Rx DMA */ 118 #define CANFD_CTL_IRQ_TL_DEF 10 /* Time before IRQ if < CL (x100 µs) */ 119 120 #define CANFD_OPTIONS_SET (CANFD_OPTION_ERROR | CANFD_OPTION_BUSLOAD) 121 122 /* Tx anticipation window (link logical address should be aligned on 2K 123 * boundary) 124 */ 125 #define PCIEFD_TX_PAGE_COUNT (PCIEFD_TX_DMA_SIZE / PCIEFD_TX_PAGE_SIZE) 126 127 #define CANFD_MSG_LNK_TX 0x1001 /* Tx msgs link */ 128 129 /* 32-bits IRQ status fields, heading Rx DMA area */ 130 static inline int pciefd_irq_tag(u32 irq_status) 131 { 132 return irq_status & 0x0000000f; 133 } 134 135 static inline int pciefd_irq_rx_cnt(u32 irq_status) 136 { 137 return (irq_status & 0x000007f0) >> 4; 138 } 139 140 static inline int pciefd_irq_is_lnk(u32 irq_status) 141 { 142 return irq_status & 0x00010000; 143 } 144 145 /* Rx record */ 146 struct pciefd_rx_dma { 147 __le32 irq_status; 148 __le32 sys_time_low; 149 __le32 sys_time_high; 150 struct pucan_rx_msg msg[0]; 151 } __packed __aligned(4); 152 153 /* Tx Link record */ 154 struct pciefd_tx_link { 155 __le16 size; 156 __le16 type; 157 __le32 laddr_lo; 158 __le32 laddr_hi; 159 } __packed __aligned(4); 160 161 /* Tx page descriptor */ 162 struct pciefd_page { 163 void *vbase; /* page virtual address */ 164 dma_addr_t lbase; /* page logical address */ 165 u32 offset; 166 u32 size; 167 }; 168 169 /* CAN-FD channel object */ 170 struct pciefd_board; 171 struct pciefd_can { 172 struct peak_canfd_priv ucan; /* must be the first member */ 173 void __iomem *reg_base; /* channel config base addr */ 174 struct pciefd_board *board; /* reverse link */ 175 176 struct pucan_command pucan_cmd; /* command buffer */ 177 178 dma_addr_t rx_dma_laddr; /* DMA virtual and logical addr */ 179 void *rx_dma_vaddr; /* for Rx and Tx areas */ 180 dma_addr_t tx_dma_laddr; 181 void *tx_dma_vaddr; 182 183 struct pciefd_page tx_pages[PCIEFD_TX_PAGE_COUNT]; 184 u16 tx_pages_free; /* free Tx pages counter */ 185 u16 tx_page_index; /* current page used for Tx */ 186 spinlock_t tx_lock; 187 188 u32 irq_status; 189 u32 irq_tag; /* next irq tag */ 190 }; 191 192 /* PEAK-PCIe FD board object */ 193 struct pciefd_board { 194 void __iomem *reg_base; 195 struct pci_dev *pci_dev; 196 int can_count; 197 spinlock_t cmd_lock; /* 64-bits cmds must be atomic */ 198 struct pciefd_can *can[0]; /* array of network devices */ 199 }; 200 201 /* supported device ids. */ 202 static const struct pci_device_id peak_pciefd_tbl[] = { 203 {PEAK_PCI_VENDOR_ID, PEAK_PCIEFD_ID, PCI_ANY_ID, PCI_ANY_ID,}, 204 {PEAK_PCI_VENDOR_ID, PCAN_CPCIEFD_ID, PCI_ANY_ID, PCI_ANY_ID,}, 205 {PEAK_PCI_VENDOR_ID, PCAN_PCIE104FD_ID, PCI_ANY_ID, PCI_ANY_ID,}, 206 {PEAK_PCI_VENDOR_ID, PCAN_MINIPCIEFD_ID, PCI_ANY_ID, PCI_ANY_ID,}, 207 {PEAK_PCI_VENDOR_ID, PCAN_PCIEFD_OEM_ID, PCI_ANY_ID, PCI_ANY_ID,}, 208 {PEAK_PCI_VENDOR_ID, PCAN_M2_ID, PCI_ANY_ID, PCI_ANY_ID,}, 209 {0,} 210 }; 211 212 MODULE_DEVICE_TABLE(pci, peak_pciefd_tbl); 213 214 /* read a 32 bits value from a SYS block register */ 215 static inline u32 pciefd_sys_readreg(const struct pciefd_board *priv, u16 reg) 216 { 217 return readl(priv->reg_base + reg); 218 } 219 220 /* write a 32 bits value into a SYS block register */ 221 static inline void pciefd_sys_writereg(const struct pciefd_board *priv, 222 u32 val, u16 reg) 223 { 224 writel(val, priv->reg_base + reg); 225 } 226 227 /* read a 32 bits value from CAN-FD block register */ 228 static inline u32 pciefd_can_readreg(const struct pciefd_can *priv, u16 reg) 229 { 230 return readl(priv->reg_base + reg); 231 } 232 233 /* write a 32 bits value into a CAN-FD block register */ 234 static inline void pciefd_can_writereg(const struct pciefd_can *priv, 235 u32 val, u16 reg) 236 { 237 writel(val, priv->reg_base + reg); 238 } 239 240 /* give a channel logical Rx DMA address to the board */ 241 static void pciefd_can_setup_rx_dma(struct pciefd_can *priv) 242 { 243 #ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT 244 const u32 dma_addr_h = (u32)(priv->rx_dma_laddr >> 32); 245 #else 246 const u32 dma_addr_h = 0; 247 #endif 248 249 /* (DMA must be reset for Rx) */ 250 pciefd_can_writereg(priv, CANFD_CTL_RST_BIT, PCIEFD_REG_CAN_RX_CTL_SET); 251 252 /* write the logical address of the Rx DMA area for this channel */ 253 pciefd_can_writereg(priv, (u32)priv->rx_dma_laddr, 254 PCIEFD_REG_CAN_RX_DMA_ADDR_L); 255 pciefd_can_writereg(priv, dma_addr_h, PCIEFD_REG_CAN_RX_DMA_ADDR_H); 256 257 /* also indicates that Rx DMA is cacheable */ 258 pciefd_can_writereg(priv, CANFD_CTL_UNC_BIT, PCIEFD_REG_CAN_RX_CTL_CLR); 259 } 260 261 /* clear channel logical Rx DMA address from the board */ 262 static void pciefd_can_clear_rx_dma(struct pciefd_can *priv) 263 { 264 /* DMA must be reset for Rx */ 265 pciefd_can_writereg(priv, CANFD_CTL_RST_BIT, PCIEFD_REG_CAN_RX_CTL_SET); 266 267 /* clear the logical address of the Rx DMA area for this channel */ 268 pciefd_can_writereg(priv, 0, PCIEFD_REG_CAN_RX_DMA_ADDR_L); 269 pciefd_can_writereg(priv, 0, PCIEFD_REG_CAN_RX_DMA_ADDR_H); 270 } 271 272 /* give a channel logical Tx DMA address to the board */ 273 static void pciefd_can_setup_tx_dma(struct pciefd_can *priv) 274 { 275 #ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT 276 const u32 dma_addr_h = (u32)(priv->tx_dma_laddr >> 32); 277 #else 278 const u32 dma_addr_h = 0; 279 #endif 280 281 /* (DMA must be reset for Tx) */ 282 pciefd_can_writereg(priv, CANFD_CTL_RST_BIT, PCIEFD_REG_CAN_TX_CTL_SET); 283 284 /* write the logical address of the Tx DMA area for this channel */ 285 pciefd_can_writereg(priv, (u32)priv->tx_dma_laddr, 286 PCIEFD_REG_CAN_TX_DMA_ADDR_L); 287 pciefd_can_writereg(priv, dma_addr_h, PCIEFD_REG_CAN_TX_DMA_ADDR_H); 288 289 /* also indicates that Tx DMA is cacheable */ 290 pciefd_can_writereg(priv, CANFD_CTL_UNC_BIT, PCIEFD_REG_CAN_TX_CTL_CLR); 291 } 292 293 /* clear channel logical Tx DMA address from the board */ 294 static void pciefd_can_clear_tx_dma(struct pciefd_can *priv) 295 { 296 /* DMA must be reset for Tx */ 297 pciefd_can_writereg(priv, CANFD_CTL_RST_BIT, PCIEFD_REG_CAN_TX_CTL_SET); 298 299 /* clear the logical address of the Tx DMA area for this channel */ 300 pciefd_can_writereg(priv, 0, PCIEFD_REG_CAN_TX_DMA_ADDR_L); 301 pciefd_can_writereg(priv, 0, PCIEFD_REG_CAN_TX_DMA_ADDR_H); 302 } 303 304 static void pciefd_can_ack_rx_dma(struct pciefd_can *priv) 305 { 306 /* read value of current IRQ tag and inc it for next one */ 307 priv->irq_tag = le32_to_cpu(*(__le32 *)priv->rx_dma_vaddr); 308 priv->irq_tag++; 309 priv->irq_tag &= 0xf; 310 311 /* write the next IRQ tag for this CAN */ 312 pciefd_can_writereg(priv, priv->irq_tag, PCIEFD_REG_CAN_RX_CTL_ACK); 313 } 314 315 /* IRQ handler */ 316 static irqreturn_t pciefd_irq_handler(int irq, void *arg) 317 { 318 struct pciefd_can *priv = arg; 319 struct pciefd_rx_dma *rx_dma = priv->rx_dma_vaddr; 320 321 /* INTA mode only to sync with PCIe transaction */ 322 if (!pci_dev_msi_enabled(priv->board->pci_dev)) 323 (void)pciefd_sys_readreg(priv->board, PCIEFD_REG_SYS_VER1); 324 325 /* read IRQ status from the first 32-bits of the Rx DMA area */ 326 priv->irq_status = le32_to_cpu(rx_dma->irq_status); 327 328 /* check if this (shared) IRQ is for this CAN */ 329 if (pciefd_irq_tag(priv->irq_status) != priv->irq_tag) 330 return IRQ_NONE; 331 332 /* handle rx messages (if any) */ 333 peak_canfd_handle_msgs_list(&priv->ucan, 334 rx_dma->msg, 335 pciefd_irq_rx_cnt(priv->irq_status)); 336 337 /* handle tx link interrupt (if any) */ 338 if (pciefd_irq_is_lnk(priv->irq_status)) { 339 unsigned long flags; 340 341 spin_lock_irqsave(&priv->tx_lock, flags); 342 priv->tx_pages_free++; 343 spin_unlock_irqrestore(&priv->tx_lock, flags); 344 345 /* wake producer up (only if enough room in echo_skb array) */ 346 spin_lock_irqsave(&priv->ucan.echo_lock, flags); 347 if (!priv->ucan.can.echo_skb[priv->ucan.echo_idx]) 348 netif_wake_queue(priv->ucan.ndev); 349 350 spin_unlock_irqrestore(&priv->ucan.echo_lock, flags); 351 } 352 353 /* re-enable Rx DMA transfer for this CAN */ 354 pciefd_can_ack_rx_dma(priv); 355 356 return IRQ_HANDLED; 357 } 358 359 static int pciefd_enable_tx_path(struct peak_canfd_priv *ucan) 360 { 361 struct pciefd_can *priv = (struct pciefd_can *)ucan; 362 int i; 363 364 /* initialize the Tx pages descriptors */ 365 priv->tx_pages_free = PCIEFD_TX_PAGE_COUNT - 1; 366 priv->tx_page_index = 0; 367 368 priv->tx_pages[0].vbase = priv->tx_dma_vaddr; 369 priv->tx_pages[0].lbase = priv->tx_dma_laddr; 370 371 for (i = 0; i < PCIEFD_TX_PAGE_COUNT; i++) { 372 priv->tx_pages[i].offset = 0; 373 priv->tx_pages[i].size = PCIEFD_TX_PAGE_SIZE - 374 sizeof(struct pciefd_tx_link); 375 if (i) { 376 priv->tx_pages[i].vbase = 377 priv->tx_pages[i - 1].vbase + 378 PCIEFD_TX_PAGE_SIZE; 379 priv->tx_pages[i].lbase = 380 priv->tx_pages[i - 1].lbase + 381 PCIEFD_TX_PAGE_SIZE; 382 } 383 } 384 385 /* setup Tx DMA addresses into IP core */ 386 pciefd_can_setup_tx_dma(priv); 387 388 /* start (TX_RST=0) Tx Path */ 389 pciefd_can_writereg(priv, CANFD_CTL_RST_BIT, PCIEFD_REG_CAN_TX_CTL_CLR); 390 391 return 0; 392 } 393 394 /* board specific CANFD command pre-processing */ 395 static int pciefd_pre_cmd(struct peak_canfd_priv *ucan) 396 { 397 struct pciefd_can *priv = (struct pciefd_can *)ucan; 398 u16 cmd = pucan_cmd_get_opcode(&priv->pucan_cmd); 399 int err; 400 401 /* pre-process command */ 402 switch (cmd) { 403 case PUCAN_CMD_NORMAL_MODE: 404 case PUCAN_CMD_LISTEN_ONLY_MODE: 405 406 if (ucan->can.state == CAN_STATE_BUS_OFF) 407 break; 408 409 /* going into operational mode: setup IRQ handler */ 410 err = request_irq(priv->ucan.ndev->irq, 411 pciefd_irq_handler, 412 IRQF_SHARED, 413 PCIEFD_DRV_NAME, 414 priv); 415 if (err) 416 return err; 417 418 /* setup Rx DMA address */ 419 pciefd_can_setup_rx_dma(priv); 420 421 /* setup max count of msgs per IRQ */ 422 pciefd_can_writereg(priv, (CANFD_CTL_IRQ_TL_DEF) << 8 | 423 CANFD_CTL_IRQ_CL_DEF, 424 PCIEFD_REG_CAN_RX_CTL_WRT); 425 426 /* clear DMA RST for Rx (Rx start) */ 427 pciefd_can_writereg(priv, CANFD_CTL_RST_BIT, 428 PCIEFD_REG_CAN_RX_CTL_CLR); 429 430 /* reset timestamps */ 431 pciefd_can_writereg(priv, !CANFD_MISC_TS_RST, 432 PCIEFD_REG_CAN_MISC); 433 434 /* do an initial ACK */ 435 pciefd_can_ack_rx_dma(priv); 436 437 /* enable IRQ for this CAN after having set next irq_tag */ 438 pciefd_can_writereg(priv, CANFD_CTL_IEN_BIT, 439 PCIEFD_REG_CAN_RX_CTL_SET); 440 441 /* Tx path will be setup as soon as RX_BARRIER is received */ 442 break; 443 default: 444 break; 445 } 446 447 return 0; 448 } 449 450 /* write a command */ 451 static int pciefd_write_cmd(struct peak_canfd_priv *ucan) 452 { 453 struct pciefd_can *priv = (struct pciefd_can *)ucan; 454 unsigned long flags; 455 456 /* 64-bits command is atomic */ 457 spin_lock_irqsave(&priv->board->cmd_lock, flags); 458 459 pciefd_can_writereg(priv, *(u32 *)ucan->cmd_buffer, 460 PCIEFD_REG_CAN_CMD_PORT_L); 461 pciefd_can_writereg(priv, *(u32 *)(ucan->cmd_buffer + 4), 462 PCIEFD_REG_CAN_CMD_PORT_H); 463 464 spin_unlock_irqrestore(&priv->board->cmd_lock, flags); 465 466 return 0; 467 } 468 469 /* board specific CANFD command post-processing */ 470 static int pciefd_post_cmd(struct peak_canfd_priv *ucan) 471 { 472 struct pciefd_can *priv = (struct pciefd_can *)ucan; 473 u16 cmd = pucan_cmd_get_opcode(&priv->pucan_cmd); 474 475 switch (cmd) { 476 case PUCAN_CMD_RESET_MODE: 477 478 if (ucan->can.state == CAN_STATE_STOPPED) 479 break; 480 481 /* controller now in reset mode: */ 482 483 /* disable IRQ for this CAN */ 484 pciefd_can_writereg(priv, CANFD_CTL_IEN_BIT, 485 PCIEFD_REG_CAN_RX_CTL_CLR); 486 487 /* stop and reset DMA addresses in Tx/Rx engines */ 488 pciefd_can_clear_tx_dma(priv); 489 pciefd_can_clear_rx_dma(priv); 490 491 /* wait for above commands to complete (read cycle) */ 492 (void)pciefd_sys_readreg(priv->board, PCIEFD_REG_SYS_VER1); 493 494 free_irq(priv->ucan.ndev->irq, priv); 495 496 ucan->can.state = CAN_STATE_STOPPED; 497 498 break; 499 } 500 501 return 0; 502 } 503 504 static void *pciefd_alloc_tx_msg(struct peak_canfd_priv *ucan, u16 msg_size, 505 int *room_left) 506 { 507 struct pciefd_can *priv = (struct pciefd_can *)ucan; 508 struct pciefd_page *page = priv->tx_pages + priv->tx_page_index; 509 unsigned long flags; 510 void *msg; 511 512 spin_lock_irqsave(&priv->tx_lock, flags); 513 514 if (page->offset + msg_size > page->size) { 515 struct pciefd_tx_link *lk; 516 517 /* not enough space in this page: try another one */ 518 if (!priv->tx_pages_free) { 519 spin_unlock_irqrestore(&priv->tx_lock, flags); 520 521 /* Tx overflow */ 522 return NULL; 523 } 524 525 priv->tx_pages_free--; 526 527 /* keep address of the very last free slot of current page */ 528 lk = page->vbase + page->offset; 529 530 /* next, move on a new free page */ 531 priv->tx_page_index = (priv->tx_page_index + 1) % 532 PCIEFD_TX_PAGE_COUNT; 533 page = priv->tx_pages + priv->tx_page_index; 534 535 /* put link record to this new page at the end of prev one */ 536 lk->size = cpu_to_le16(sizeof(*lk)); 537 lk->type = cpu_to_le16(CANFD_MSG_LNK_TX); 538 lk->laddr_lo = cpu_to_le32(page->lbase); 539 540 #ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT 541 lk->laddr_hi = cpu_to_le32(page->lbase >> 32); 542 #else 543 lk->laddr_hi = 0; 544 #endif 545 /* next msgs will be put from the begininng of this new page */ 546 page->offset = 0; 547 } 548 549 *room_left = priv->tx_pages_free * page->size; 550 551 spin_unlock_irqrestore(&priv->tx_lock, flags); 552 553 msg = page->vbase + page->offset; 554 555 /* give back room left in the tx ring */ 556 *room_left += page->size - (page->offset + msg_size); 557 558 return msg; 559 } 560 561 static int pciefd_write_tx_msg(struct peak_canfd_priv *ucan, 562 struct pucan_tx_msg *msg) 563 { 564 struct pciefd_can *priv = (struct pciefd_can *)ucan; 565 struct pciefd_page *page = priv->tx_pages + priv->tx_page_index; 566 567 /* this slot is now reserved for writing the frame */ 568 page->offset += le16_to_cpu(msg->size); 569 570 /* tell the board a frame has been written in Tx DMA area */ 571 pciefd_can_writereg(priv, 1, PCIEFD_REG_CAN_TX_REQ_ACC); 572 573 return 0; 574 } 575 576 /* probe for CAN-FD channel #pciefd_board->can_count */ 577 static int pciefd_can_probe(struct pciefd_board *pciefd) 578 { 579 struct net_device *ndev; 580 struct pciefd_can *priv; 581 u32 clk; 582 int err; 583 584 /* allocate the candev object with default isize of echo skbs ring */ 585 ndev = alloc_peak_canfd_dev(sizeof(*priv), pciefd->can_count, 586 PCIEFD_ECHO_SKB_MAX); 587 if (!ndev) { 588 dev_err(&pciefd->pci_dev->dev, 589 "failed to alloc candev object\n"); 590 goto failure; 591 } 592 593 priv = netdev_priv(ndev); 594 595 /* fill-in candev private object: */ 596 597 /* setup PCIe-FD own callbacks */ 598 priv->ucan.pre_cmd = pciefd_pre_cmd; 599 priv->ucan.write_cmd = pciefd_write_cmd; 600 priv->ucan.post_cmd = pciefd_post_cmd; 601 priv->ucan.enable_tx_path = pciefd_enable_tx_path; 602 priv->ucan.alloc_tx_msg = pciefd_alloc_tx_msg; 603 priv->ucan.write_tx_msg = pciefd_write_tx_msg; 604 605 /* setup PCIe-FD own command buffer */ 606 priv->ucan.cmd_buffer = &priv->pucan_cmd; 607 priv->ucan.cmd_maxlen = sizeof(priv->pucan_cmd); 608 609 priv->board = pciefd; 610 611 /* CAN config regs block address */ 612 priv->reg_base = pciefd->reg_base + PCIEFD_CANX_OFF(priv->ucan.index); 613 614 /* allocate non-cacheable DMA'able 4KB memory area for Rx */ 615 priv->rx_dma_vaddr = dmam_alloc_coherent(&pciefd->pci_dev->dev, 616 PCIEFD_RX_DMA_SIZE, 617 &priv->rx_dma_laddr, 618 GFP_KERNEL); 619 if (!priv->rx_dma_vaddr) { 620 dev_err(&pciefd->pci_dev->dev, 621 "Rx dmam_alloc_coherent(%u) failure\n", 622 PCIEFD_RX_DMA_SIZE); 623 goto err_free_candev; 624 } 625 626 /* allocate non-cacheable DMA'able 4KB memory area for Tx */ 627 priv->tx_dma_vaddr = dmam_alloc_coherent(&pciefd->pci_dev->dev, 628 PCIEFD_TX_DMA_SIZE, 629 &priv->tx_dma_laddr, 630 GFP_KERNEL); 631 if (!priv->tx_dma_vaddr) { 632 dev_err(&pciefd->pci_dev->dev, 633 "Tx dmam_alloc_coherent(%u) failure\n", 634 PCIEFD_TX_DMA_SIZE); 635 goto err_free_candev; 636 } 637 638 /* CAN clock in RST mode */ 639 pciefd_can_writereg(priv, CANFD_MISC_TS_RST, PCIEFD_REG_CAN_MISC); 640 641 /* read current clock value */ 642 clk = pciefd_can_readreg(priv, PCIEFD_REG_CAN_CLK_SEL); 643 switch (clk) { 644 case CANFD_CLK_SEL_20MHZ: 645 priv->ucan.can.clock.freq = 20 * 1000 * 1000; 646 break; 647 case CANFD_CLK_SEL_24MHZ: 648 priv->ucan.can.clock.freq = 24 * 1000 * 1000; 649 break; 650 case CANFD_CLK_SEL_30MHZ: 651 priv->ucan.can.clock.freq = 30 * 1000 * 1000; 652 break; 653 case CANFD_CLK_SEL_40MHZ: 654 priv->ucan.can.clock.freq = 40 * 1000 * 1000; 655 break; 656 case CANFD_CLK_SEL_60MHZ: 657 priv->ucan.can.clock.freq = 60 * 1000 * 1000; 658 break; 659 default: 660 pciefd_can_writereg(priv, CANFD_CLK_SEL_80MHZ, 661 PCIEFD_REG_CAN_CLK_SEL); 662 663 /* fallthough */ 664 case CANFD_CLK_SEL_80MHZ: 665 priv->ucan.can.clock.freq = 80 * 1000 * 1000; 666 break; 667 } 668 669 ndev->irq = pciefd->pci_dev->irq; 670 671 SET_NETDEV_DEV(ndev, &pciefd->pci_dev->dev); 672 673 err = register_candev(ndev); 674 if (err) { 675 dev_err(&pciefd->pci_dev->dev, 676 "couldn't register CAN device: %d\n", err); 677 goto err_free_candev; 678 } 679 680 spin_lock_init(&priv->tx_lock); 681 682 /* save the object address in the board structure */ 683 pciefd->can[pciefd->can_count] = priv; 684 685 dev_info(&pciefd->pci_dev->dev, "%s at reg_base=0x%p irq=%d\n", 686 ndev->name, priv->reg_base, ndev->irq); 687 688 return 0; 689 690 err_free_candev: 691 free_candev(ndev); 692 693 failure: 694 return -ENOMEM; 695 } 696 697 /* remove a CAN-FD channel by releasing all of its resources */ 698 static void pciefd_can_remove(struct pciefd_can *priv) 699 { 700 /* unregister (close) the can device to go back to RST mode first */ 701 unregister_candev(priv->ucan.ndev); 702 703 /* finally, free the candev object */ 704 free_candev(priv->ucan.ndev); 705 } 706 707 /* remove all CAN-FD channels by releasing their own resources */ 708 static void pciefd_can_remove_all(struct pciefd_board *pciefd) 709 { 710 while (pciefd->can_count > 0) 711 pciefd_can_remove(pciefd->can[--pciefd->can_count]); 712 } 713 714 /* probe for the entire device */ 715 static int peak_pciefd_probe(struct pci_dev *pdev, 716 const struct pci_device_id *ent) 717 { 718 struct pciefd_board *pciefd; 719 int err, can_count; 720 u16 sub_sys_id; 721 u8 hw_ver_major; 722 u8 hw_ver_minor; 723 u8 hw_ver_sub; 724 u32 v2; 725 726 err = pci_enable_device(pdev); 727 if (err) 728 return err; 729 err = pci_request_regions(pdev, PCIEFD_DRV_NAME); 730 if (err) 731 goto err_disable_pci; 732 733 /* the number of channels depends on sub-system id */ 734 err = pci_read_config_word(pdev, PCI_SUBSYSTEM_ID, &sub_sys_id); 735 if (err) 736 goto err_release_regions; 737 738 dev_dbg(&pdev->dev, "probing device %04x:%04x:%04x\n", 739 pdev->vendor, pdev->device, sub_sys_id); 740 741 if (sub_sys_id >= 0x0012) 742 can_count = 4; 743 else if (sub_sys_id >= 0x0010) 744 can_count = 3; 745 else if (sub_sys_id >= 0x0004) 746 can_count = 2; 747 else 748 can_count = 1; 749 750 /* allocate board structure object */ 751 pciefd = devm_kzalloc(&pdev->dev, struct_size(pciefd, can, can_count), 752 GFP_KERNEL); 753 if (!pciefd) { 754 err = -ENOMEM; 755 goto err_release_regions; 756 } 757 758 /* initialize the board structure */ 759 pciefd->pci_dev = pdev; 760 spin_lock_init(&pciefd->cmd_lock); 761 762 /* save the PCI BAR0 virtual address for further system regs access */ 763 pciefd->reg_base = pci_iomap(pdev, 0, PCIEFD_BAR0_SIZE); 764 if (!pciefd->reg_base) { 765 dev_err(&pdev->dev, "failed to map PCI resource #0\n"); 766 err = -ENOMEM; 767 goto err_release_regions; 768 } 769 770 /* read the firmware version number */ 771 v2 = pciefd_sys_readreg(pciefd, PCIEFD_REG_SYS_VER2); 772 773 hw_ver_major = (v2 & 0x0000f000) >> 12; 774 hw_ver_minor = (v2 & 0x00000f00) >> 8; 775 hw_ver_sub = (v2 & 0x000000f0) >> 4; 776 777 dev_info(&pdev->dev, 778 "%ux CAN-FD PCAN-PCIe FPGA v%u.%u.%u:\n", can_count, 779 hw_ver_major, hw_ver_minor, hw_ver_sub); 780 781 #ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT 782 /* FW < v3.3.0 DMA logic doesn't handle correctly the mix of 32-bit and 783 * 64-bit logical addresses: this workaround forces usage of 32-bit 784 * DMA addresses only when such a fw is detected. 785 */ 786 if (PCIEFD_FW_VERSION(hw_ver_major, hw_ver_minor, hw_ver_sub) < 787 PCIEFD_FW_VERSION(3, 3, 0)) { 788 err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); 789 if (err) 790 dev_warn(&pdev->dev, 791 "warning: can't set DMA mask %llxh (err %d)\n", 792 DMA_BIT_MASK(32), err); 793 } 794 #endif 795 796 /* stop system clock */ 797 pciefd_sys_writereg(pciefd, PCIEFD_SYS_CTL_CLK_EN, 798 PCIEFD_REG_SYS_CTL_CLR); 799 800 pci_set_master(pdev); 801 802 /* create now the corresponding channels objects */ 803 while (pciefd->can_count < can_count) { 804 err = pciefd_can_probe(pciefd); 805 if (err) 806 goto err_free_canfd; 807 808 pciefd->can_count++; 809 } 810 811 /* set system timestamps counter in RST mode */ 812 pciefd_sys_writereg(pciefd, PCIEFD_SYS_CTL_TS_RST, 813 PCIEFD_REG_SYS_CTL_SET); 814 815 /* wait a bit (read cycle) */ 816 (void)pciefd_sys_readreg(pciefd, PCIEFD_REG_SYS_VER1); 817 818 /* free all clocks */ 819 pciefd_sys_writereg(pciefd, PCIEFD_SYS_CTL_TS_RST, 820 PCIEFD_REG_SYS_CTL_CLR); 821 822 /* start system clock */ 823 pciefd_sys_writereg(pciefd, PCIEFD_SYS_CTL_CLK_EN, 824 PCIEFD_REG_SYS_CTL_SET); 825 826 /* remember the board structure address in the device user data */ 827 pci_set_drvdata(pdev, pciefd); 828 829 return 0; 830 831 err_free_canfd: 832 pciefd_can_remove_all(pciefd); 833 834 pci_iounmap(pdev, pciefd->reg_base); 835 836 err_release_regions: 837 pci_release_regions(pdev); 838 839 err_disable_pci: 840 pci_disable_device(pdev); 841 842 /* pci_xxx_config_word() return positive PCIBIOS_xxx error codes while 843 * the probe() function must return a negative errno in case of failure 844 * (err is unchanged if negative) */ 845 return pcibios_err_to_errno(err); 846 } 847 848 /* free the board structure object, as well as its resources: */ 849 static void peak_pciefd_remove(struct pci_dev *pdev) 850 { 851 struct pciefd_board *pciefd = pci_get_drvdata(pdev); 852 853 /* release CAN-FD channels resources */ 854 pciefd_can_remove_all(pciefd); 855 856 pci_iounmap(pdev, pciefd->reg_base); 857 858 pci_release_regions(pdev); 859 pci_disable_device(pdev); 860 } 861 862 static struct pci_driver peak_pciefd_driver = { 863 .name = PCIEFD_DRV_NAME, 864 .id_table = peak_pciefd_tbl, 865 .probe = peak_pciefd_probe, 866 .remove = peak_pciefd_remove, 867 }; 868 869 module_pci_driver(peak_pciefd_driver); 870