1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Janz MODULbus VMOD-ICAN3 CAN Interface Driver 4 * 5 * Copyright (c) 2010 Ira W. Snyder <iws@ovro.caltech.edu> 6 */ 7 8 #include <linux/kernel.h> 9 #include <linux/module.h> 10 #include <linux/interrupt.h> 11 #include <linux/delay.h> 12 #include <linux/platform_device.h> 13 14 #include <linux/netdevice.h> 15 #include <linux/can.h> 16 #include <linux/can/dev.h> 17 #include <linux/can/skb.h> 18 #include <linux/can/error.h> 19 20 #include <linux/mfd/janz.h> 21 #include <asm/io.h> 22 23 /* the DPM has 64k of memory, organized into 256x 256 byte pages */ 24 #define DPM_NUM_PAGES 256 25 #define DPM_PAGE_SIZE 256 26 #define DPM_PAGE_ADDR(p) ((p) * DPM_PAGE_SIZE) 27 28 /* JANZ ICAN3 "old-style" host interface queue page numbers */ 29 #define QUEUE_OLD_CONTROL 0 30 #define QUEUE_OLD_RB0 1 31 #define QUEUE_OLD_RB1 2 32 #define QUEUE_OLD_WB0 3 33 #define QUEUE_OLD_WB1 4 34 35 /* Janz ICAN3 "old-style" host interface control registers */ 36 #define MSYNC_PEER 0x00 /* ICAN only */ 37 #define MSYNC_LOCL 0x01 /* host only */ 38 #define TARGET_RUNNING 0x02 39 #define FIRMWARE_STAMP 0x60 /* big endian firmware stamp */ 40 41 #define MSYNC_RB0 0x01 42 #define MSYNC_RB1 0x02 43 #define MSYNC_RBLW 0x04 44 #define MSYNC_RB_MASK (MSYNC_RB0 | MSYNC_RB1) 45 46 #define MSYNC_WB0 0x10 47 #define MSYNC_WB1 0x20 48 #define MSYNC_WBLW 0x40 49 #define MSYNC_WB_MASK (MSYNC_WB0 | MSYNC_WB1) 50 51 /* Janz ICAN3 "new-style" host interface queue page numbers */ 52 #define QUEUE_TOHOST 5 53 #define QUEUE_FROMHOST_MID 6 54 #define QUEUE_FROMHOST_HIGH 7 55 #define QUEUE_FROMHOST_LOW 8 56 57 /* The first free page in the DPM is #9 */ 58 #define DPM_FREE_START 9 59 60 /* Janz ICAN3 "new-style" and "fast" host interface descriptor flags */ 61 #define DESC_VALID 0x80 62 #define DESC_WRAP 0x40 63 #define DESC_INTERRUPT 0x20 64 #define DESC_IVALID 0x10 65 #define DESC_LEN(len) (len) 66 67 /* Janz ICAN3 Firmware Messages */ 68 #define MSG_CONNECTI 0x02 69 #define MSG_DISCONNECT 0x03 70 #define MSG_IDVERS 0x04 71 #define MSG_MSGLOST 0x05 72 #define MSG_NEWHOSTIF 0x08 73 #define MSG_INQUIRY 0x0a 74 #define MSG_SETAFILMASK 0x10 75 #define MSG_INITFDPMQUEUE 0x11 76 #define MSG_HWCONF 0x12 77 #define MSG_FMSGLOST 0x15 78 #define MSG_CEVTIND 0x37 79 #define MSG_CBTRREQ 0x41 80 #define MSG_COFFREQ 0x42 81 #define MSG_CONREQ 0x43 82 #define MSG_CCONFREQ 0x47 83 #define MSG_NMTS 0xb0 84 #define MSG_LMTS 0xb4 85 86 /* 87 * Janz ICAN3 CAN Inquiry Message Types 88 * 89 * NOTE: there appears to be a firmware bug here. You must send 90 * NOTE: INQUIRY_STATUS and expect to receive an INQUIRY_EXTENDED 91 * NOTE: response. The controller never responds to a message with 92 * NOTE: the INQUIRY_EXTENDED subspec :( 93 */ 94 #define INQUIRY_STATUS 0x00 95 #define INQUIRY_TERMINATION 0x01 96 #define INQUIRY_EXTENDED 0x04 97 98 /* Janz ICAN3 CAN Set Acceptance Filter Mask Message Types */ 99 #define SETAFILMASK_REJECT 0x00 100 #define SETAFILMASK_FASTIF 0x02 101 102 /* Janz ICAN3 CAN Hardware Configuration Message Types */ 103 #define HWCONF_TERMINATE_ON 0x01 104 #define HWCONF_TERMINATE_OFF 0x00 105 106 /* Janz ICAN3 CAN Event Indication Message Types */ 107 #define CEVTIND_EI 0x01 108 #define CEVTIND_DOI 0x02 109 #define CEVTIND_LOST 0x04 110 #define CEVTIND_FULL 0x08 111 #define CEVTIND_BEI 0x10 112 113 #define CEVTIND_CHIP_SJA1000 0x02 114 115 #define ICAN3_BUSERR_QUOTA_MAX 255 116 117 /* Janz ICAN3 CAN Frame Conversion */ 118 #define ICAN3_SNGL 0x02 119 #define ICAN3_ECHO 0x10 120 #define ICAN3_EFF_RTR 0x40 121 #define ICAN3_SFF_RTR 0x10 122 #define ICAN3_EFF 0x80 123 124 #define ICAN3_CAN_TYPE_MASK 0x0f 125 #define ICAN3_CAN_TYPE_SFF 0x00 126 #define ICAN3_CAN_TYPE_EFF 0x01 127 128 #define ICAN3_CAN_DLC_MASK 0x0f 129 130 /* Janz ICAN3 NMTS subtypes */ 131 #define NMTS_CREATE_NODE_REQ 0x0 132 #define NMTS_SLAVE_STATE_IND 0x8 133 #define NMTS_SLAVE_EVENT_IND 0x9 134 135 /* Janz ICAN3 LMTS subtypes */ 136 #define LMTS_BUSON_REQ 0x0 137 #define LMTS_BUSOFF_REQ 0x1 138 #define LMTS_CAN_CONF_REQ 0x2 139 140 /* Janz ICAN3 NMTS Event indications */ 141 #define NE_LOCAL_OCCURRED 0x3 142 #define NE_LOCAL_RESOLVED 0x2 143 #define NE_REMOTE_OCCURRED 0xc 144 #define NE_REMOTE_RESOLVED 0x8 145 146 /* 147 * SJA1000 Status and Error Register Definitions 148 * 149 * Copied from drivers/net/can/sja1000/sja1000.h 150 */ 151 152 /* status register content */ 153 #define SR_BS 0x80 154 #define SR_ES 0x40 155 #define SR_TS 0x20 156 #define SR_RS 0x10 157 #define SR_TCS 0x08 158 #define SR_TBS 0x04 159 #define SR_DOS 0x02 160 #define SR_RBS 0x01 161 162 #define SR_CRIT (SR_BS|SR_ES) 163 164 /* ECC register */ 165 #define ECC_SEG 0x1F 166 #define ECC_DIR 0x20 167 #define ECC_ERR 6 168 #define ECC_BIT 0x00 169 #define ECC_FORM 0x40 170 #define ECC_STUFF 0x80 171 #define ECC_MASK 0xc0 172 173 /* Number of buffers for use in the "new-style" host interface */ 174 #define ICAN3_NEW_BUFFERS 16 175 176 /* Number of buffers for use in the "fast" host interface */ 177 #define ICAN3_TX_BUFFERS 512 178 #define ICAN3_RX_BUFFERS 1024 179 180 /* SJA1000 Clock Input */ 181 #define ICAN3_CAN_CLOCK 8000000 182 183 /* Janz ICAN3 firmware types */ 184 enum ican3_fwtype { 185 ICAN3_FWTYPE_ICANOS, 186 ICAN3_FWTYPE_CAL_CANOPEN, 187 }; 188 189 /* Driver Name */ 190 #define DRV_NAME "janz-ican3" 191 192 /* DPM Control Registers -- starts at offset 0x100 in the MODULbus registers */ 193 struct ican3_dpm_control { 194 /* window address register */ 195 u8 window_address; 196 u8 unused1; 197 198 /* 199 * Read access: clear interrupt from microcontroller 200 * Write access: send interrupt to microcontroller 201 */ 202 u8 interrupt; 203 u8 unused2; 204 205 /* write-only: reset all hardware on the module */ 206 u8 hwreset; 207 u8 unused3; 208 209 /* write-only: generate an interrupt to the TPU */ 210 u8 tpuinterrupt; 211 }; 212 213 struct ican3_dev { 214 215 /* must be the first member */ 216 struct can_priv can; 217 218 /* CAN network device */ 219 struct net_device *ndev; 220 struct napi_struct napi; 221 222 /* module number */ 223 unsigned int num; 224 225 /* base address of registers and IRQ */ 226 struct janz_cmodio_onboard_regs __iomem *ctrl; 227 struct ican3_dpm_control __iomem *dpmctrl; 228 void __iomem *dpm; 229 int irq; 230 231 /* CAN bus termination status */ 232 struct completion termination_comp; 233 bool termination_enabled; 234 235 /* CAN bus error status registers */ 236 struct completion buserror_comp; 237 struct can_berr_counter bec; 238 239 /* firmware type */ 240 enum ican3_fwtype fwtype; 241 char fwinfo[32]; 242 243 /* old and new style host interface */ 244 unsigned int iftype; 245 246 /* queue for echo packets */ 247 struct sk_buff_head echoq; 248 249 /* 250 * Any function which changes the current DPM page must hold this 251 * lock while it is performing data accesses. This ensures that the 252 * function will not be preempted and end up reading data from a 253 * different DPM page than it expects. 254 */ 255 spinlock_t lock; 256 257 /* new host interface */ 258 unsigned int rx_int; 259 unsigned int rx_num; 260 unsigned int tx_num; 261 262 /* fast host interface */ 263 unsigned int fastrx_start; 264 unsigned int fastrx_num; 265 unsigned int fasttx_start; 266 unsigned int fasttx_num; 267 268 /* first free DPM page */ 269 unsigned int free_page; 270 }; 271 272 struct ican3_msg { 273 u8 control; 274 u8 spec; 275 __le16 len; 276 u8 data[252]; 277 }; 278 279 struct ican3_new_desc { 280 u8 control; 281 u8 pointer; 282 }; 283 284 struct ican3_fast_desc { 285 u8 control; 286 u8 command; 287 u8 data[14]; 288 }; 289 290 /* write to the window basic address register */ 291 static inline void ican3_set_page(struct ican3_dev *mod, unsigned int page) 292 { 293 BUG_ON(page >= DPM_NUM_PAGES); 294 iowrite8(page, &mod->dpmctrl->window_address); 295 } 296 297 /* 298 * ICAN3 "old-style" host interface 299 */ 300 301 /* 302 * Receive a message from the ICAN3 "old-style" firmware interface 303 * 304 * LOCKING: must hold mod->lock 305 * 306 * returns 0 on success, -ENOMEM when no message exists 307 */ 308 static int ican3_old_recv_msg(struct ican3_dev *mod, struct ican3_msg *msg) 309 { 310 unsigned int mbox, mbox_page; 311 u8 locl, peer, xord; 312 313 /* get the MSYNC registers */ 314 ican3_set_page(mod, QUEUE_OLD_CONTROL); 315 peer = ioread8(mod->dpm + MSYNC_PEER); 316 locl = ioread8(mod->dpm + MSYNC_LOCL); 317 xord = locl ^ peer; 318 319 if ((xord & MSYNC_RB_MASK) == 0x00) { 320 netdev_dbg(mod->ndev, "no mbox for reading\n"); 321 return -ENOMEM; 322 } 323 324 /* find the first free mbox to read */ 325 if ((xord & MSYNC_RB_MASK) == MSYNC_RB_MASK) 326 mbox = (xord & MSYNC_RBLW) ? MSYNC_RB0 : MSYNC_RB1; 327 else 328 mbox = (xord & MSYNC_RB0) ? MSYNC_RB0 : MSYNC_RB1; 329 330 /* copy the message */ 331 mbox_page = (mbox == MSYNC_RB0) ? QUEUE_OLD_RB0 : QUEUE_OLD_RB1; 332 ican3_set_page(mod, mbox_page); 333 memcpy_fromio(msg, mod->dpm, sizeof(*msg)); 334 335 /* 336 * notify the firmware that the read buffer is available 337 * for it to fill again 338 */ 339 locl ^= mbox; 340 341 ican3_set_page(mod, QUEUE_OLD_CONTROL); 342 iowrite8(locl, mod->dpm + MSYNC_LOCL); 343 return 0; 344 } 345 346 /* 347 * Send a message through the "old-style" firmware interface 348 * 349 * LOCKING: must hold mod->lock 350 * 351 * returns 0 on success, -ENOMEM when no free space exists 352 */ 353 static int ican3_old_send_msg(struct ican3_dev *mod, struct ican3_msg *msg) 354 { 355 unsigned int mbox, mbox_page; 356 u8 locl, peer, xord; 357 358 /* get the MSYNC registers */ 359 ican3_set_page(mod, QUEUE_OLD_CONTROL); 360 peer = ioread8(mod->dpm + MSYNC_PEER); 361 locl = ioread8(mod->dpm + MSYNC_LOCL); 362 xord = locl ^ peer; 363 364 if ((xord & MSYNC_WB_MASK) == MSYNC_WB_MASK) { 365 netdev_err(mod->ndev, "no mbox for writing\n"); 366 return -ENOMEM; 367 } 368 369 /* calculate a free mbox to use */ 370 mbox = (xord & MSYNC_WB0) ? MSYNC_WB1 : MSYNC_WB0; 371 372 /* copy the message to the DPM */ 373 mbox_page = (mbox == MSYNC_WB0) ? QUEUE_OLD_WB0 : QUEUE_OLD_WB1; 374 ican3_set_page(mod, mbox_page); 375 memcpy_toio(mod->dpm, msg, sizeof(*msg)); 376 377 locl ^= mbox; 378 if (mbox == MSYNC_WB1) 379 locl |= MSYNC_WBLW; 380 381 ican3_set_page(mod, QUEUE_OLD_CONTROL); 382 iowrite8(locl, mod->dpm + MSYNC_LOCL); 383 return 0; 384 } 385 386 /* 387 * ICAN3 "new-style" Host Interface Setup 388 */ 389 390 static void ican3_init_new_host_interface(struct ican3_dev *mod) 391 { 392 struct ican3_new_desc desc; 393 unsigned long flags; 394 void __iomem *dst; 395 int i; 396 397 spin_lock_irqsave(&mod->lock, flags); 398 399 /* setup the internal datastructures for RX */ 400 mod->rx_num = 0; 401 mod->rx_int = 0; 402 403 /* tohost queue descriptors are in page 5 */ 404 ican3_set_page(mod, QUEUE_TOHOST); 405 dst = mod->dpm; 406 407 /* initialize the tohost (rx) queue descriptors: pages 9-24 */ 408 for (i = 0; i < ICAN3_NEW_BUFFERS; i++) { 409 desc.control = DESC_INTERRUPT | DESC_LEN(1); /* I L=1 */ 410 desc.pointer = mod->free_page; 411 412 /* set wrap flag on last buffer */ 413 if (i == ICAN3_NEW_BUFFERS - 1) 414 desc.control |= DESC_WRAP; 415 416 memcpy_toio(dst, &desc, sizeof(desc)); 417 dst += sizeof(desc); 418 mod->free_page++; 419 } 420 421 /* fromhost (tx) mid queue descriptors are in page 6 */ 422 ican3_set_page(mod, QUEUE_FROMHOST_MID); 423 dst = mod->dpm; 424 425 /* setup the internal datastructures for TX */ 426 mod->tx_num = 0; 427 428 /* initialize the fromhost mid queue descriptors: pages 25-40 */ 429 for (i = 0; i < ICAN3_NEW_BUFFERS; i++) { 430 desc.control = DESC_VALID | DESC_LEN(1); /* V L=1 */ 431 desc.pointer = mod->free_page; 432 433 /* set wrap flag on last buffer */ 434 if (i == ICAN3_NEW_BUFFERS - 1) 435 desc.control |= DESC_WRAP; 436 437 memcpy_toio(dst, &desc, sizeof(desc)); 438 dst += sizeof(desc); 439 mod->free_page++; 440 } 441 442 /* fromhost hi queue descriptors are in page 7 */ 443 ican3_set_page(mod, QUEUE_FROMHOST_HIGH); 444 dst = mod->dpm; 445 446 /* initialize only a single buffer in the fromhost hi queue (unused) */ 447 desc.control = DESC_VALID | DESC_WRAP | DESC_LEN(1); /* VW L=1 */ 448 desc.pointer = mod->free_page; 449 memcpy_toio(dst, &desc, sizeof(desc)); 450 mod->free_page++; 451 452 /* fromhost low queue descriptors are in page 8 */ 453 ican3_set_page(mod, QUEUE_FROMHOST_LOW); 454 dst = mod->dpm; 455 456 /* initialize only a single buffer in the fromhost low queue (unused) */ 457 desc.control = DESC_VALID | DESC_WRAP | DESC_LEN(1); /* VW L=1 */ 458 desc.pointer = mod->free_page; 459 memcpy_toio(dst, &desc, sizeof(desc)); 460 mod->free_page++; 461 462 spin_unlock_irqrestore(&mod->lock, flags); 463 } 464 465 /* 466 * ICAN3 Fast Host Interface Setup 467 */ 468 469 static void ican3_init_fast_host_interface(struct ican3_dev *mod) 470 { 471 struct ican3_fast_desc desc; 472 unsigned long flags; 473 unsigned int addr; 474 void __iomem *dst; 475 int i; 476 477 spin_lock_irqsave(&mod->lock, flags); 478 479 /* save the start recv page */ 480 mod->fastrx_start = mod->free_page; 481 mod->fastrx_num = 0; 482 483 /* build a single fast tohost queue descriptor */ 484 memset(&desc, 0, sizeof(desc)); 485 desc.control = 0x00; 486 desc.command = 1; 487 488 /* build the tohost queue descriptor ring in memory */ 489 addr = 0; 490 for (i = 0; i < ICAN3_RX_BUFFERS; i++) { 491 492 /* set the wrap bit on the last buffer */ 493 if (i == ICAN3_RX_BUFFERS - 1) 494 desc.control |= DESC_WRAP; 495 496 /* switch to the correct page */ 497 ican3_set_page(mod, mod->free_page); 498 499 /* copy the descriptor to the DPM */ 500 dst = mod->dpm + addr; 501 memcpy_toio(dst, &desc, sizeof(desc)); 502 addr += sizeof(desc); 503 504 /* move to the next page if necessary */ 505 if (addr >= DPM_PAGE_SIZE) { 506 addr = 0; 507 mod->free_page++; 508 } 509 } 510 511 /* make sure we page-align the next queue */ 512 if (addr != 0) 513 mod->free_page++; 514 515 /* save the start xmit page */ 516 mod->fasttx_start = mod->free_page; 517 mod->fasttx_num = 0; 518 519 /* build a single fast fromhost queue descriptor */ 520 memset(&desc, 0, sizeof(desc)); 521 desc.control = DESC_VALID; 522 desc.command = 1; 523 524 /* build the fromhost queue descriptor ring in memory */ 525 addr = 0; 526 for (i = 0; i < ICAN3_TX_BUFFERS; i++) { 527 528 /* set the wrap bit on the last buffer */ 529 if (i == ICAN3_TX_BUFFERS - 1) 530 desc.control |= DESC_WRAP; 531 532 /* switch to the correct page */ 533 ican3_set_page(mod, mod->free_page); 534 535 /* copy the descriptor to the DPM */ 536 dst = mod->dpm + addr; 537 memcpy_toio(dst, &desc, sizeof(desc)); 538 addr += sizeof(desc); 539 540 /* move to the next page if necessary */ 541 if (addr >= DPM_PAGE_SIZE) { 542 addr = 0; 543 mod->free_page++; 544 } 545 } 546 547 spin_unlock_irqrestore(&mod->lock, flags); 548 } 549 550 /* 551 * ICAN3 "new-style" Host Interface Message Helpers 552 */ 553 554 /* 555 * LOCKING: must hold mod->lock 556 */ 557 static int ican3_new_send_msg(struct ican3_dev *mod, struct ican3_msg *msg) 558 { 559 struct ican3_new_desc desc; 560 void __iomem *desc_addr = mod->dpm + (mod->tx_num * sizeof(desc)); 561 562 /* switch to the fromhost mid queue, and read the buffer descriptor */ 563 ican3_set_page(mod, QUEUE_FROMHOST_MID); 564 memcpy_fromio(&desc, desc_addr, sizeof(desc)); 565 566 if (!(desc.control & DESC_VALID)) { 567 netdev_dbg(mod->ndev, "%s: no free buffers\n", __func__); 568 return -ENOMEM; 569 } 570 571 /* switch to the data page, copy the data */ 572 ican3_set_page(mod, desc.pointer); 573 memcpy_toio(mod->dpm, msg, sizeof(*msg)); 574 575 /* switch back to the descriptor, set the valid bit, write it back */ 576 ican3_set_page(mod, QUEUE_FROMHOST_MID); 577 desc.control ^= DESC_VALID; 578 memcpy_toio(desc_addr, &desc, sizeof(desc)); 579 580 /* update the tx number */ 581 mod->tx_num = (desc.control & DESC_WRAP) ? 0 : (mod->tx_num + 1); 582 return 0; 583 } 584 585 /* 586 * LOCKING: must hold mod->lock 587 */ 588 static int ican3_new_recv_msg(struct ican3_dev *mod, struct ican3_msg *msg) 589 { 590 struct ican3_new_desc desc; 591 void __iomem *desc_addr = mod->dpm + (mod->rx_num * sizeof(desc)); 592 593 /* switch to the tohost queue, and read the buffer descriptor */ 594 ican3_set_page(mod, QUEUE_TOHOST); 595 memcpy_fromio(&desc, desc_addr, sizeof(desc)); 596 597 if (!(desc.control & DESC_VALID)) { 598 netdev_dbg(mod->ndev, "%s: no buffers to recv\n", __func__); 599 return -ENOMEM; 600 } 601 602 /* switch to the data page, copy the data */ 603 ican3_set_page(mod, desc.pointer); 604 memcpy_fromio(msg, mod->dpm, sizeof(*msg)); 605 606 /* switch back to the descriptor, toggle the valid bit, write it back */ 607 ican3_set_page(mod, QUEUE_TOHOST); 608 desc.control ^= DESC_VALID; 609 memcpy_toio(desc_addr, &desc, sizeof(desc)); 610 611 /* update the rx number */ 612 mod->rx_num = (desc.control & DESC_WRAP) ? 0 : (mod->rx_num + 1); 613 return 0; 614 } 615 616 /* 617 * Message Send / Recv Helpers 618 */ 619 620 static int ican3_send_msg(struct ican3_dev *mod, struct ican3_msg *msg) 621 { 622 unsigned long flags; 623 int ret; 624 625 spin_lock_irqsave(&mod->lock, flags); 626 627 if (mod->iftype == 0) 628 ret = ican3_old_send_msg(mod, msg); 629 else 630 ret = ican3_new_send_msg(mod, msg); 631 632 spin_unlock_irqrestore(&mod->lock, flags); 633 return ret; 634 } 635 636 static int ican3_recv_msg(struct ican3_dev *mod, struct ican3_msg *msg) 637 { 638 unsigned long flags; 639 int ret; 640 641 spin_lock_irqsave(&mod->lock, flags); 642 643 if (mod->iftype == 0) 644 ret = ican3_old_recv_msg(mod, msg); 645 else 646 ret = ican3_new_recv_msg(mod, msg); 647 648 spin_unlock_irqrestore(&mod->lock, flags); 649 return ret; 650 } 651 652 /* 653 * Quick Pre-constructed Messages 654 */ 655 656 static int ican3_msg_connect(struct ican3_dev *mod) 657 { 658 struct ican3_msg msg; 659 660 memset(&msg, 0, sizeof(msg)); 661 msg.spec = MSG_CONNECTI; 662 msg.len = cpu_to_le16(0); 663 664 return ican3_send_msg(mod, &msg); 665 } 666 667 static int ican3_msg_disconnect(struct ican3_dev *mod) 668 { 669 struct ican3_msg msg; 670 671 memset(&msg, 0, sizeof(msg)); 672 msg.spec = MSG_DISCONNECT; 673 msg.len = cpu_to_le16(0); 674 675 return ican3_send_msg(mod, &msg); 676 } 677 678 static int ican3_msg_newhostif(struct ican3_dev *mod) 679 { 680 struct ican3_msg msg; 681 int ret; 682 683 memset(&msg, 0, sizeof(msg)); 684 msg.spec = MSG_NEWHOSTIF; 685 msg.len = cpu_to_le16(0); 686 687 /* If we're not using the old interface, switching seems bogus */ 688 WARN_ON(mod->iftype != 0); 689 690 ret = ican3_send_msg(mod, &msg); 691 if (ret) 692 return ret; 693 694 /* mark the module as using the new host interface */ 695 mod->iftype = 1; 696 return 0; 697 } 698 699 static int ican3_msg_fasthostif(struct ican3_dev *mod) 700 { 701 struct ican3_msg msg; 702 unsigned int addr; 703 704 memset(&msg, 0, sizeof(msg)); 705 msg.spec = MSG_INITFDPMQUEUE; 706 msg.len = cpu_to_le16(8); 707 708 /* write the tohost queue start address */ 709 addr = DPM_PAGE_ADDR(mod->fastrx_start); 710 msg.data[0] = addr & 0xff; 711 msg.data[1] = (addr >> 8) & 0xff; 712 msg.data[2] = (addr >> 16) & 0xff; 713 msg.data[3] = (addr >> 24) & 0xff; 714 715 /* write the fromhost queue start address */ 716 addr = DPM_PAGE_ADDR(mod->fasttx_start); 717 msg.data[4] = addr & 0xff; 718 msg.data[5] = (addr >> 8) & 0xff; 719 msg.data[6] = (addr >> 16) & 0xff; 720 msg.data[7] = (addr >> 24) & 0xff; 721 722 /* If we're not using the new interface yet, we cannot do this */ 723 WARN_ON(mod->iftype != 1); 724 725 return ican3_send_msg(mod, &msg); 726 } 727 728 /* 729 * Setup the CAN filter to either accept or reject all 730 * messages from the CAN bus. 731 */ 732 static int ican3_set_id_filter(struct ican3_dev *mod, bool accept) 733 { 734 struct ican3_msg msg; 735 int ret; 736 737 /* Standard Frame Format */ 738 memset(&msg, 0, sizeof(msg)); 739 msg.spec = MSG_SETAFILMASK; 740 msg.len = cpu_to_le16(5); 741 msg.data[0] = 0x00; /* IDLo LSB */ 742 msg.data[1] = 0x00; /* IDLo MSB */ 743 msg.data[2] = 0xff; /* IDHi LSB */ 744 msg.data[3] = 0x07; /* IDHi MSB */ 745 746 /* accept all frames for fast host if, or reject all frames */ 747 msg.data[4] = accept ? SETAFILMASK_FASTIF : SETAFILMASK_REJECT; 748 749 ret = ican3_send_msg(mod, &msg); 750 if (ret) 751 return ret; 752 753 /* Extended Frame Format */ 754 memset(&msg, 0, sizeof(msg)); 755 msg.spec = MSG_SETAFILMASK; 756 msg.len = cpu_to_le16(13); 757 msg.data[0] = 0; /* MUX = 0 */ 758 msg.data[1] = 0x00; /* IDLo LSB */ 759 msg.data[2] = 0x00; 760 msg.data[3] = 0x00; 761 msg.data[4] = 0x20; /* IDLo MSB */ 762 msg.data[5] = 0xff; /* IDHi LSB */ 763 msg.data[6] = 0xff; 764 msg.data[7] = 0xff; 765 msg.data[8] = 0x3f; /* IDHi MSB */ 766 767 /* accept all frames for fast host if, or reject all frames */ 768 msg.data[9] = accept ? SETAFILMASK_FASTIF : SETAFILMASK_REJECT; 769 770 return ican3_send_msg(mod, &msg); 771 } 772 773 /* 774 * Bring the CAN bus online or offline 775 */ 776 static int ican3_set_bus_state(struct ican3_dev *mod, bool on) 777 { 778 struct can_bittiming *bt = &mod->can.bittiming; 779 struct ican3_msg msg; 780 u8 btr0, btr1; 781 int res; 782 783 /* This algorithm was stolen from drivers/net/can/sja1000/sja1000.c */ 784 /* The bittiming register command for the ICAN3 just sets the bit timing */ 785 /* registers on the SJA1000 chip directly */ 786 btr0 = ((bt->brp - 1) & 0x3f) | (((bt->sjw - 1) & 0x3) << 6); 787 btr1 = ((bt->prop_seg + bt->phase_seg1 - 1) & 0xf) | 788 (((bt->phase_seg2 - 1) & 0x7) << 4); 789 if (mod->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES) 790 btr1 |= 0x80; 791 792 if (mod->fwtype == ICAN3_FWTYPE_ICANOS) { 793 if (on) { 794 /* set bittiming */ 795 memset(&msg, 0, sizeof(msg)); 796 msg.spec = MSG_CBTRREQ; 797 msg.len = cpu_to_le16(4); 798 msg.data[0] = 0x00; 799 msg.data[1] = 0x00; 800 msg.data[2] = btr0; 801 msg.data[3] = btr1; 802 803 res = ican3_send_msg(mod, &msg); 804 if (res) 805 return res; 806 } 807 808 /* can-on/off request */ 809 memset(&msg, 0, sizeof(msg)); 810 msg.spec = on ? MSG_CONREQ : MSG_COFFREQ; 811 msg.len = cpu_to_le16(0); 812 813 return ican3_send_msg(mod, &msg); 814 815 } else if (mod->fwtype == ICAN3_FWTYPE_CAL_CANOPEN) { 816 /* bittiming + can-on/off request */ 817 memset(&msg, 0, sizeof(msg)); 818 msg.spec = MSG_LMTS; 819 if (on) { 820 msg.len = cpu_to_le16(4); 821 msg.data[0] = LMTS_BUSON_REQ; 822 msg.data[1] = 0; 823 msg.data[2] = btr0; 824 msg.data[3] = btr1; 825 } else { 826 msg.len = cpu_to_le16(2); 827 msg.data[0] = LMTS_BUSOFF_REQ; 828 msg.data[1] = 0; 829 } 830 res = ican3_send_msg(mod, &msg); 831 if (res) 832 return res; 833 834 if (on) { 835 /* create NMT Slave Node for error processing 836 * class 2 (with error capability, see CiA/DS203-1) 837 * id 1 838 * name locnod1 (must be exactly 7 bytes) 839 */ 840 memset(&msg, 0, sizeof(msg)); 841 msg.spec = MSG_NMTS; 842 msg.len = cpu_to_le16(11); 843 msg.data[0] = NMTS_CREATE_NODE_REQ; 844 msg.data[1] = 0; 845 msg.data[2] = 2; /* node class */ 846 msg.data[3] = 1; /* node id */ 847 strcpy(msg.data + 4, "locnod1"); /* node name */ 848 return ican3_send_msg(mod, &msg); 849 } 850 return 0; 851 } 852 return -ENOTSUPP; 853 } 854 855 static int ican3_set_termination(struct ican3_dev *mod, bool on) 856 { 857 struct ican3_msg msg; 858 859 memset(&msg, 0, sizeof(msg)); 860 msg.spec = MSG_HWCONF; 861 msg.len = cpu_to_le16(2); 862 msg.data[0] = 0x00; 863 msg.data[1] = on ? HWCONF_TERMINATE_ON : HWCONF_TERMINATE_OFF; 864 865 return ican3_send_msg(mod, &msg); 866 } 867 868 static int ican3_send_inquiry(struct ican3_dev *mod, u8 subspec) 869 { 870 struct ican3_msg msg; 871 872 memset(&msg, 0, sizeof(msg)); 873 msg.spec = MSG_INQUIRY; 874 msg.len = cpu_to_le16(2); 875 msg.data[0] = subspec; 876 msg.data[1] = 0x00; 877 878 return ican3_send_msg(mod, &msg); 879 } 880 881 static int ican3_set_buserror(struct ican3_dev *mod, u8 quota) 882 { 883 struct ican3_msg msg; 884 885 if (mod->fwtype == ICAN3_FWTYPE_ICANOS) { 886 memset(&msg, 0, sizeof(msg)); 887 msg.spec = MSG_CCONFREQ; 888 msg.len = cpu_to_le16(2); 889 msg.data[0] = 0x00; 890 msg.data[1] = quota; 891 } else if (mod->fwtype == ICAN3_FWTYPE_CAL_CANOPEN) { 892 memset(&msg, 0, sizeof(msg)); 893 msg.spec = MSG_LMTS; 894 msg.len = cpu_to_le16(4); 895 msg.data[0] = LMTS_CAN_CONF_REQ; 896 msg.data[1] = 0x00; 897 msg.data[2] = 0x00; 898 msg.data[3] = quota; 899 } else { 900 return -ENOTSUPP; 901 } 902 return ican3_send_msg(mod, &msg); 903 } 904 905 /* 906 * ICAN3 to Linux CAN Frame Conversion 907 */ 908 909 static void ican3_to_can_frame(struct ican3_dev *mod, 910 struct ican3_fast_desc *desc, 911 struct can_frame *cf) 912 { 913 if ((desc->command & ICAN3_CAN_TYPE_MASK) == ICAN3_CAN_TYPE_SFF) { 914 if (desc->data[1] & ICAN3_SFF_RTR) 915 cf->can_id |= CAN_RTR_FLAG; 916 917 cf->can_id |= desc->data[0] << 3; 918 cf->can_id |= (desc->data[1] & 0xe0) >> 5; 919 cf->len = can_cc_dlc2len(desc->data[1] & ICAN3_CAN_DLC_MASK); 920 memcpy(cf->data, &desc->data[2], cf->len); 921 } else { 922 cf->len = can_cc_dlc2len(desc->data[0] & ICAN3_CAN_DLC_MASK); 923 if (desc->data[0] & ICAN3_EFF_RTR) 924 cf->can_id |= CAN_RTR_FLAG; 925 926 if (desc->data[0] & ICAN3_EFF) { 927 cf->can_id |= CAN_EFF_FLAG; 928 cf->can_id |= desc->data[2] << 21; /* 28-21 */ 929 cf->can_id |= desc->data[3] << 13; /* 20-13 */ 930 cf->can_id |= desc->data[4] << 5; /* 12-5 */ 931 cf->can_id |= (desc->data[5] & 0xf8) >> 3; 932 } else { 933 cf->can_id |= desc->data[2] << 3; /* 10-3 */ 934 cf->can_id |= desc->data[3] >> 5; /* 2-0 */ 935 } 936 937 memcpy(cf->data, &desc->data[6], cf->len); 938 } 939 } 940 941 static void can_frame_to_ican3(struct ican3_dev *mod, 942 struct can_frame *cf, 943 struct ican3_fast_desc *desc) 944 { 945 /* clear out any stale data in the descriptor */ 946 memset(desc->data, 0, sizeof(desc->data)); 947 948 /* we always use the extended format, with the ECHO flag set */ 949 desc->command = ICAN3_CAN_TYPE_EFF; 950 desc->data[0] |= cf->len; 951 desc->data[1] |= ICAN3_ECHO; 952 953 /* support single transmission (no retries) mode */ 954 if (mod->can.ctrlmode & CAN_CTRLMODE_ONE_SHOT) 955 desc->data[1] |= ICAN3_SNGL; 956 957 if (cf->can_id & CAN_RTR_FLAG) 958 desc->data[0] |= ICAN3_EFF_RTR; 959 960 /* pack the id into the correct places */ 961 if (cf->can_id & CAN_EFF_FLAG) { 962 desc->data[0] |= ICAN3_EFF; 963 desc->data[2] = (cf->can_id & 0x1fe00000) >> 21; /* 28-21 */ 964 desc->data[3] = (cf->can_id & 0x001fe000) >> 13; /* 20-13 */ 965 desc->data[4] = (cf->can_id & 0x00001fe0) >> 5; /* 12-5 */ 966 desc->data[5] = (cf->can_id & 0x0000001f) << 3; /* 4-0 */ 967 } else { 968 desc->data[2] = (cf->can_id & 0x7F8) >> 3; /* bits 10-3 */ 969 desc->data[3] = (cf->can_id & 0x007) << 5; /* bits 2-0 */ 970 } 971 972 /* copy the data bits into the descriptor */ 973 memcpy(&desc->data[6], cf->data, cf->len); 974 } 975 976 /* 977 * Interrupt Handling 978 */ 979 980 /* 981 * Handle an ID + Version message response from the firmware. We never generate 982 * this message in production code, but it is very useful when debugging to be 983 * able to display this message. 984 */ 985 static void ican3_handle_idvers(struct ican3_dev *mod, struct ican3_msg *msg) 986 { 987 netdev_dbg(mod->ndev, "IDVERS response: %s\n", msg->data); 988 } 989 990 static void ican3_handle_msglost(struct ican3_dev *mod, struct ican3_msg *msg) 991 { 992 struct net_device *dev = mod->ndev; 993 struct net_device_stats *stats = &dev->stats; 994 struct can_frame *cf; 995 struct sk_buff *skb; 996 997 /* 998 * Report that communication messages with the microcontroller firmware 999 * are being lost. These are never CAN frames, so we do not generate an 1000 * error frame for userspace 1001 */ 1002 if (msg->spec == MSG_MSGLOST) { 1003 netdev_err(mod->ndev, "lost %d control messages\n", msg->data[0]); 1004 return; 1005 } 1006 1007 /* 1008 * Oops, this indicates that we have lost messages in the fast queue, 1009 * which are exclusively CAN messages. Our driver isn't reading CAN 1010 * frames fast enough. 1011 * 1012 * We'll pretend that the SJA1000 told us that it ran out of buffer 1013 * space, because there is not a better message for this. 1014 */ 1015 skb = alloc_can_err_skb(dev, &cf); 1016 if (skb) { 1017 cf->can_id |= CAN_ERR_CRTL; 1018 cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; 1019 stats->rx_over_errors++; 1020 stats->rx_errors++; 1021 netif_rx(skb); 1022 } 1023 } 1024 1025 /* 1026 * Handle CAN Event Indication Messages from the firmware 1027 * 1028 * The ICAN3 firmware provides the values of some SJA1000 registers when it 1029 * generates this message. The code below is largely copied from the 1030 * drivers/net/can/sja1000/sja1000.c file, and adapted as necessary 1031 */ 1032 static int ican3_handle_cevtind(struct ican3_dev *mod, struct ican3_msg *msg) 1033 { 1034 struct net_device *dev = mod->ndev; 1035 struct net_device_stats *stats = &dev->stats; 1036 enum can_state state = mod->can.state; 1037 u8 isrc, ecc, status, rxerr, txerr; 1038 struct can_frame *cf; 1039 struct sk_buff *skb; 1040 1041 /* we can only handle the SJA1000 part */ 1042 if (msg->data[1] != CEVTIND_CHIP_SJA1000) { 1043 netdev_err(mod->ndev, "unable to handle errors on non-SJA1000\n"); 1044 return -ENODEV; 1045 } 1046 1047 /* check the message length for sanity */ 1048 if (le16_to_cpu(msg->len) < 6) { 1049 netdev_err(mod->ndev, "error message too short\n"); 1050 return -EINVAL; 1051 } 1052 1053 isrc = msg->data[0]; 1054 ecc = msg->data[2]; 1055 status = msg->data[3]; 1056 rxerr = msg->data[4]; 1057 txerr = msg->data[5]; 1058 1059 /* 1060 * This hardware lacks any support other than bus error messages to 1061 * determine if packet transmission has failed. 1062 * 1063 * When TX errors happen, one echo skb needs to be dropped from the 1064 * front of the queue. 1065 * 1066 * A small bit of code is duplicated here and below, to avoid error 1067 * skb allocation when it will just be freed immediately. 1068 */ 1069 if (isrc == CEVTIND_BEI) { 1070 int ret; 1071 netdev_dbg(mod->ndev, "bus error interrupt\n"); 1072 1073 /* TX error */ 1074 if (!(ecc & ECC_DIR)) { 1075 kfree_skb(skb_dequeue(&mod->echoq)); 1076 stats->tx_errors++; 1077 } else { 1078 stats->rx_errors++; 1079 } 1080 1081 /* 1082 * The controller automatically disables bus-error interrupts 1083 * and therefore we must re-enable them. 1084 */ 1085 ret = ican3_set_buserror(mod, 1); 1086 if (ret) { 1087 netdev_err(mod->ndev, "unable to re-enable bus-error\n"); 1088 return ret; 1089 } 1090 1091 /* bus error reporting is off, return immediately */ 1092 if (!(mod->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)) 1093 return 0; 1094 } 1095 1096 skb = alloc_can_err_skb(dev, &cf); 1097 if (skb == NULL) 1098 return -ENOMEM; 1099 1100 /* data overrun interrupt */ 1101 if (isrc == CEVTIND_DOI || isrc == CEVTIND_LOST) { 1102 netdev_dbg(mod->ndev, "data overrun interrupt\n"); 1103 cf->can_id |= CAN_ERR_CRTL; 1104 cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; 1105 stats->rx_over_errors++; 1106 stats->rx_errors++; 1107 } 1108 1109 /* error warning + passive interrupt */ 1110 if (isrc == CEVTIND_EI) { 1111 netdev_dbg(mod->ndev, "error warning + passive interrupt\n"); 1112 if (status & SR_BS) { 1113 state = CAN_STATE_BUS_OFF; 1114 cf->can_id |= CAN_ERR_BUSOFF; 1115 mod->can.can_stats.bus_off++; 1116 can_bus_off(dev); 1117 } else if (status & SR_ES) { 1118 if (rxerr >= 128 || txerr >= 128) 1119 state = CAN_STATE_ERROR_PASSIVE; 1120 else 1121 state = CAN_STATE_ERROR_WARNING; 1122 } else { 1123 state = CAN_STATE_ERROR_ACTIVE; 1124 } 1125 } 1126 1127 /* bus error interrupt */ 1128 if (isrc == CEVTIND_BEI) { 1129 mod->can.can_stats.bus_error++; 1130 cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR; 1131 1132 switch (ecc & ECC_MASK) { 1133 case ECC_BIT: 1134 cf->data[2] |= CAN_ERR_PROT_BIT; 1135 break; 1136 case ECC_FORM: 1137 cf->data[2] |= CAN_ERR_PROT_FORM; 1138 break; 1139 case ECC_STUFF: 1140 cf->data[2] |= CAN_ERR_PROT_STUFF; 1141 break; 1142 default: 1143 cf->data[3] = ecc & ECC_SEG; 1144 break; 1145 } 1146 1147 if (!(ecc & ECC_DIR)) 1148 cf->data[2] |= CAN_ERR_PROT_TX; 1149 1150 cf->data[6] = txerr; 1151 cf->data[7] = rxerr; 1152 } 1153 1154 if (state != mod->can.state && (state == CAN_STATE_ERROR_WARNING || 1155 state == CAN_STATE_ERROR_PASSIVE)) { 1156 cf->can_id |= CAN_ERR_CRTL; 1157 if (state == CAN_STATE_ERROR_WARNING) { 1158 mod->can.can_stats.error_warning++; 1159 cf->data[1] = (txerr > rxerr) ? 1160 CAN_ERR_CRTL_TX_WARNING : 1161 CAN_ERR_CRTL_RX_WARNING; 1162 } else { 1163 mod->can.can_stats.error_passive++; 1164 cf->data[1] = (txerr > rxerr) ? 1165 CAN_ERR_CRTL_TX_PASSIVE : 1166 CAN_ERR_CRTL_RX_PASSIVE; 1167 } 1168 1169 cf->data[6] = txerr; 1170 cf->data[7] = rxerr; 1171 } 1172 1173 mod->can.state = state; 1174 netif_rx(skb); 1175 return 0; 1176 } 1177 1178 static void ican3_handle_inquiry(struct ican3_dev *mod, struct ican3_msg *msg) 1179 { 1180 switch (msg->data[0]) { 1181 case INQUIRY_STATUS: 1182 case INQUIRY_EXTENDED: 1183 mod->bec.rxerr = msg->data[5]; 1184 mod->bec.txerr = msg->data[6]; 1185 complete(&mod->buserror_comp); 1186 break; 1187 case INQUIRY_TERMINATION: 1188 mod->termination_enabled = msg->data[6] & HWCONF_TERMINATE_ON; 1189 complete(&mod->termination_comp); 1190 break; 1191 default: 1192 netdev_err(mod->ndev, "received an unknown inquiry response\n"); 1193 break; 1194 } 1195 } 1196 1197 /* Handle NMTS Slave Event Indication Messages from the firmware */ 1198 static void ican3_handle_nmtsind(struct ican3_dev *mod, struct ican3_msg *msg) 1199 { 1200 u16 subspec; 1201 1202 subspec = msg->data[0] + msg->data[1] * 0x100; 1203 if (subspec == NMTS_SLAVE_EVENT_IND) { 1204 switch (msg->data[2]) { 1205 case NE_LOCAL_OCCURRED: 1206 case NE_LOCAL_RESOLVED: 1207 /* now follows the same message as Raw ICANOS CEVTIND 1208 * shift the data at the same place and call this method 1209 */ 1210 le16_add_cpu(&msg->len, -3); 1211 memmove(msg->data, msg->data + 3, le16_to_cpu(msg->len)); 1212 ican3_handle_cevtind(mod, msg); 1213 break; 1214 case NE_REMOTE_OCCURRED: 1215 case NE_REMOTE_RESOLVED: 1216 /* should not occurre, ignore */ 1217 break; 1218 default: 1219 netdev_warn(mod->ndev, "unknown NMTS event indication %x\n", 1220 msg->data[2]); 1221 break; 1222 } 1223 } else if (subspec == NMTS_SLAVE_STATE_IND) { 1224 /* ignore state indications */ 1225 } else { 1226 netdev_warn(mod->ndev, "unhandled NMTS indication %x\n", 1227 subspec); 1228 return; 1229 } 1230 } 1231 1232 static void ican3_handle_unknown_message(struct ican3_dev *mod, 1233 struct ican3_msg *msg) 1234 { 1235 netdev_warn(mod->ndev, "received unknown message: spec 0x%.2x length %d\n", 1236 msg->spec, le16_to_cpu(msg->len)); 1237 } 1238 1239 /* 1240 * Handle a control message from the firmware 1241 */ 1242 static void ican3_handle_message(struct ican3_dev *mod, struct ican3_msg *msg) 1243 { 1244 netdev_dbg(mod->ndev, "%s: modno %d spec 0x%.2x len %d bytes\n", __func__, 1245 mod->num, msg->spec, le16_to_cpu(msg->len)); 1246 1247 switch (msg->spec) { 1248 case MSG_IDVERS: 1249 ican3_handle_idvers(mod, msg); 1250 break; 1251 case MSG_MSGLOST: 1252 case MSG_FMSGLOST: 1253 ican3_handle_msglost(mod, msg); 1254 break; 1255 case MSG_CEVTIND: 1256 ican3_handle_cevtind(mod, msg); 1257 break; 1258 case MSG_INQUIRY: 1259 ican3_handle_inquiry(mod, msg); 1260 break; 1261 case MSG_NMTS: 1262 ican3_handle_nmtsind(mod, msg); 1263 break; 1264 default: 1265 ican3_handle_unknown_message(mod, msg); 1266 break; 1267 } 1268 } 1269 1270 /* 1271 * The ican3 needs to store all echo skbs, and therefore cannot 1272 * use the generic infrastructure for this. 1273 */ 1274 static void ican3_put_echo_skb(struct ican3_dev *mod, struct sk_buff *skb) 1275 { 1276 skb = can_create_echo_skb(skb); 1277 if (!skb) 1278 return; 1279 1280 /* save this skb for tx interrupt echo handling */ 1281 skb_queue_tail(&mod->echoq, skb); 1282 } 1283 1284 static unsigned int ican3_get_echo_skb(struct ican3_dev *mod) 1285 { 1286 struct sk_buff *skb = skb_dequeue(&mod->echoq); 1287 struct can_frame *cf; 1288 u8 dlc = 0; 1289 1290 /* this should never trigger unless there is a driver bug */ 1291 if (!skb) { 1292 netdev_err(mod->ndev, "BUG: echo skb not occupied\n"); 1293 return 0; 1294 } 1295 1296 cf = (struct can_frame *)skb->data; 1297 if (!(cf->can_id & CAN_RTR_FLAG)) 1298 dlc = cf->len; 1299 1300 /* check flag whether this packet has to be looped back */ 1301 if (skb->pkt_type != PACKET_LOOPBACK) { 1302 kfree_skb(skb); 1303 return dlc; 1304 } 1305 1306 skb->protocol = htons(ETH_P_CAN); 1307 skb->pkt_type = PACKET_BROADCAST; 1308 skb->ip_summed = CHECKSUM_UNNECESSARY; 1309 skb->dev = mod->ndev; 1310 netif_receive_skb(skb); 1311 return dlc; 1312 } 1313 1314 /* 1315 * Compare an skb with an existing echo skb 1316 * 1317 * This function will be used on devices which have a hardware loopback. 1318 * On these devices, this function can be used to compare a received skb 1319 * with the saved echo skbs so that the hardware echo skb can be dropped. 1320 * 1321 * Returns true if the skb's are identical, false otherwise. 1322 */ 1323 static bool ican3_echo_skb_matches(struct ican3_dev *mod, struct sk_buff *skb) 1324 { 1325 struct can_frame *cf = (struct can_frame *)skb->data; 1326 struct sk_buff *echo_skb = skb_peek(&mod->echoq); 1327 struct can_frame *echo_cf; 1328 1329 if (!echo_skb) 1330 return false; 1331 1332 echo_cf = (struct can_frame *)echo_skb->data; 1333 if (cf->can_id != echo_cf->can_id) 1334 return false; 1335 1336 if (cf->len != echo_cf->len) 1337 return false; 1338 1339 return memcmp(cf->data, echo_cf->data, cf->len) == 0; 1340 } 1341 1342 /* 1343 * Check that there is room in the TX ring to transmit another skb 1344 * 1345 * LOCKING: must hold mod->lock 1346 */ 1347 static bool ican3_txok(struct ican3_dev *mod) 1348 { 1349 struct ican3_fast_desc __iomem *desc; 1350 u8 control; 1351 1352 /* check that we have echo queue space */ 1353 if (skb_queue_len(&mod->echoq) >= ICAN3_TX_BUFFERS) 1354 return false; 1355 1356 /* copy the control bits of the descriptor */ 1357 ican3_set_page(mod, mod->fasttx_start + (mod->fasttx_num / 16)); 1358 desc = mod->dpm + ((mod->fasttx_num % 16) * sizeof(*desc)); 1359 control = ioread8(&desc->control); 1360 1361 /* if the control bits are not valid, then we have no more space */ 1362 if (!(control & DESC_VALID)) 1363 return false; 1364 1365 return true; 1366 } 1367 1368 /* 1369 * Receive one CAN frame from the hardware 1370 * 1371 * CONTEXT: must be called from user context 1372 */ 1373 static int ican3_recv_skb(struct ican3_dev *mod) 1374 { 1375 struct net_device *ndev = mod->ndev; 1376 struct net_device_stats *stats = &ndev->stats; 1377 struct ican3_fast_desc desc; 1378 void __iomem *desc_addr; 1379 struct can_frame *cf; 1380 struct sk_buff *skb; 1381 unsigned long flags; 1382 1383 spin_lock_irqsave(&mod->lock, flags); 1384 1385 /* copy the whole descriptor */ 1386 ican3_set_page(mod, mod->fastrx_start + (mod->fastrx_num / 16)); 1387 desc_addr = mod->dpm + ((mod->fastrx_num % 16) * sizeof(desc)); 1388 memcpy_fromio(&desc, desc_addr, sizeof(desc)); 1389 1390 spin_unlock_irqrestore(&mod->lock, flags); 1391 1392 /* check that we actually have a CAN frame */ 1393 if (!(desc.control & DESC_VALID)) 1394 return -ENOBUFS; 1395 1396 /* allocate an skb */ 1397 skb = alloc_can_skb(ndev, &cf); 1398 if (unlikely(skb == NULL)) { 1399 stats->rx_dropped++; 1400 goto err_noalloc; 1401 } 1402 1403 /* convert the ICAN3 frame into Linux CAN format */ 1404 ican3_to_can_frame(mod, &desc, cf); 1405 1406 /* 1407 * If this is an ECHO frame received from the hardware loopback 1408 * feature, use the skb saved in the ECHO stack instead. This allows 1409 * the Linux CAN core to support CAN_RAW_RECV_OWN_MSGS correctly. 1410 * 1411 * Since this is a confirmation of a successfully transmitted packet 1412 * sent from this host, update the transmit statistics. 1413 * 1414 * Also, the netdevice queue needs to be allowed to send packets again. 1415 */ 1416 if (ican3_echo_skb_matches(mod, skb)) { 1417 stats->tx_packets++; 1418 stats->tx_bytes += ican3_get_echo_skb(mod); 1419 kfree_skb(skb); 1420 goto err_noalloc; 1421 } 1422 1423 /* update statistics, receive the skb */ 1424 stats->rx_packets++; 1425 if (!(cf->can_id & CAN_RTR_FLAG)) 1426 stats->rx_bytes += cf->len; 1427 netif_receive_skb(skb); 1428 1429 err_noalloc: 1430 /* toggle the valid bit and return the descriptor to the ring */ 1431 desc.control ^= DESC_VALID; 1432 1433 spin_lock_irqsave(&mod->lock, flags); 1434 1435 ican3_set_page(mod, mod->fastrx_start + (mod->fastrx_num / 16)); 1436 memcpy_toio(desc_addr, &desc, 1); 1437 1438 /* update the next buffer pointer */ 1439 mod->fastrx_num = (desc.control & DESC_WRAP) ? 0 1440 : (mod->fastrx_num + 1); 1441 1442 /* there are still more buffers to process */ 1443 spin_unlock_irqrestore(&mod->lock, flags); 1444 return 0; 1445 } 1446 1447 static int ican3_napi(struct napi_struct *napi, int budget) 1448 { 1449 struct ican3_dev *mod = container_of(napi, struct ican3_dev, napi); 1450 unsigned long flags; 1451 int received = 0; 1452 int ret; 1453 1454 /* process all communication messages */ 1455 while (true) { 1456 struct ican3_msg msg; 1457 ret = ican3_recv_msg(mod, &msg); 1458 if (ret) 1459 break; 1460 1461 ican3_handle_message(mod, &msg); 1462 } 1463 1464 /* process all CAN frames from the fast interface */ 1465 while (received < budget) { 1466 ret = ican3_recv_skb(mod); 1467 if (ret) 1468 break; 1469 1470 received++; 1471 } 1472 1473 /* We have processed all packets that the adapter had, but it 1474 * was less than our budget, stop polling */ 1475 if (received < budget) 1476 napi_complete_done(napi, received); 1477 1478 spin_lock_irqsave(&mod->lock, flags); 1479 1480 /* Wake up the transmit queue if necessary */ 1481 if (netif_queue_stopped(mod->ndev) && ican3_txok(mod)) 1482 netif_wake_queue(mod->ndev); 1483 1484 spin_unlock_irqrestore(&mod->lock, flags); 1485 1486 /* re-enable interrupt generation */ 1487 iowrite8(1 << mod->num, &mod->ctrl->int_enable); 1488 return received; 1489 } 1490 1491 static irqreturn_t ican3_irq(int irq, void *dev_id) 1492 { 1493 struct ican3_dev *mod = dev_id; 1494 u8 stat; 1495 1496 /* 1497 * The interrupt status register on this device reports interrupts 1498 * as zeroes instead of using ones like most other devices 1499 */ 1500 stat = ioread8(&mod->ctrl->int_disable) & (1 << mod->num); 1501 if (stat == (1 << mod->num)) 1502 return IRQ_NONE; 1503 1504 /* clear the MODULbus interrupt from the microcontroller */ 1505 ioread8(&mod->dpmctrl->interrupt); 1506 1507 /* disable interrupt generation, schedule the NAPI poller */ 1508 iowrite8(1 << mod->num, &mod->ctrl->int_disable); 1509 napi_schedule(&mod->napi); 1510 return IRQ_HANDLED; 1511 } 1512 1513 /* 1514 * Firmware reset, startup, and shutdown 1515 */ 1516 1517 /* 1518 * Reset an ICAN module to its power-on state 1519 * 1520 * CONTEXT: no network device registered 1521 */ 1522 static int ican3_reset_module(struct ican3_dev *mod) 1523 { 1524 unsigned long start; 1525 u8 runold, runnew; 1526 1527 /* disable interrupts so no more work is scheduled */ 1528 iowrite8(1 << mod->num, &mod->ctrl->int_disable); 1529 1530 /* the first unallocated page in the DPM is #9 */ 1531 mod->free_page = DPM_FREE_START; 1532 1533 ican3_set_page(mod, QUEUE_OLD_CONTROL); 1534 runold = ioread8(mod->dpm + TARGET_RUNNING); 1535 1536 /* reset the module */ 1537 iowrite8(0x00, &mod->dpmctrl->hwreset); 1538 1539 /* wait until the module has finished resetting and is running */ 1540 start = jiffies; 1541 do { 1542 ican3_set_page(mod, QUEUE_OLD_CONTROL); 1543 runnew = ioread8(mod->dpm + TARGET_RUNNING); 1544 if (runnew == (runold ^ 0xff)) 1545 return 0; 1546 1547 msleep(10); 1548 } while (time_before(jiffies, start + HZ / 2)); 1549 1550 netdev_err(mod->ndev, "failed to reset CAN module\n"); 1551 return -ETIMEDOUT; 1552 } 1553 1554 static void ican3_shutdown_module(struct ican3_dev *mod) 1555 { 1556 ican3_msg_disconnect(mod); 1557 ican3_reset_module(mod); 1558 } 1559 1560 /* 1561 * Startup an ICAN module, bringing it into fast mode 1562 */ 1563 static int ican3_startup_module(struct ican3_dev *mod) 1564 { 1565 int ret; 1566 1567 ret = ican3_reset_module(mod); 1568 if (ret) { 1569 netdev_err(mod->ndev, "unable to reset module\n"); 1570 return ret; 1571 } 1572 1573 /* detect firmware */ 1574 memcpy_fromio(mod->fwinfo, mod->dpm + FIRMWARE_STAMP, sizeof(mod->fwinfo) - 1); 1575 if (strncmp(mod->fwinfo, "JANZ-ICAN3", 10)) { 1576 netdev_err(mod->ndev, "ICAN3 not detected (found %s)\n", mod->fwinfo); 1577 return -ENODEV; 1578 } 1579 if (strstr(mod->fwinfo, "CAL/CANopen")) 1580 mod->fwtype = ICAN3_FWTYPE_CAL_CANOPEN; 1581 else 1582 mod->fwtype = ICAN3_FWTYPE_ICANOS; 1583 1584 /* re-enable interrupts so we can send messages */ 1585 iowrite8(1 << mod->num, &mod->ctrl->int_enable); 1586 1587 ret = ican3_msg_connect(mod); 1588 if (ret) { 1589 netdev_err(mod->ndev, "unable to connect to module\n"); 1590 return ret; 1591 } 1592 1593 ican3_init_new_host_interface(mod); 1594 ret = ican3_msg_newhostif(mod); 1595 if (ret) { 1596 netdev_err(mod->ndev, "unable to switch to new-style interface\n"); 1597 return ret; 1598 } 1599 1600 /* default to "termination on" */ 1601 ret = ican3_set_termination(mod, true); 1602 if (ret) { 1603 netdev_err(mod->ndev, "unable to enable termination\n"); 1604 return ret; 1605 } 1606 1607 /* default to "bus errors enabled" */ 1608 ret = ican3_set_buserror(mod, 1); 1609 if (ret) { 1610 netdev_err(mod->ndev, "unable to set bus-error\n"); 1611 return ret; 1612 } 1613 1614 ican3_init_fast_host_interface(mod); 1615 ret = ican3_msg_fasthostif(mod); 1616 if (ret) { 1617 netdev_err(mod->ndev, "unable to switch to fast host interface\n"); 1618 return ret; 1619 } 1620 1621 ret = ican3_set_id_filter(mod, true); 1622 if (ret) { 1623 netdev_err(mod->ndev, "unable to set acceptance filter\n"); 1624 return ret; 1625 } 1626 1627 return 0; 1628 } 1629 1630 /* 1631 * CAN Network Device 1632 */ 1633 1634 static int ican3_open(struct net_device *ndev) 1635 { 1636 struct ican3_dev *mod = netdev_priv(ndev); 1637 int ret; 1638 1639 /* open the CAN layer */ 1640 ret = open_candev(ndev); 1641 if (ret) { 1642 netdev_err(mod->ndev, "unable to start CAN layer\n"); 1643 return ret; 1644 } 1645 1646 /* bring the bus online */ 1647 ret = ican3_set_bus_state(mod, true); 1648 if (ret) { 1649 netdev_err(mod->ndev, "unable to set bus-on\n"); 1650 close_candev(ndev); 1651 return ret; 1652 } 1653 1654 /* start up the network device */ 1655 mod->can.state = CAN_STATE_ERROR_ACTIVE; 1656 netif_start_queue(ndev); 1657 1658 return 0; 1659 } 1660 1661 static int ican3_stop(struct net_device *ndev) 1662 { 1663 struct ican3_dev *mod = netdev_priv(ndev); 1664 int ret; 1665 1666 /* stop the network device xmit routine */ 1667 netif_stop_queue(ndev); 1668 mod->can.state = CAN_STATE_STOPPED; 1669 1670 /* bring the bus offline, stop receiving packets */ 1671 ret = ican3_set_bus_state(mod, false); 1672 if (ret) { 1673 netdev_err(mod->ndev, "unable to set bus-off\n"); 1674 return ret; 1675 } 1676 1677 /* drop all outstanding echo skbs */ 1678 skb_queue_purge(&mod->echoq); 1679 1680 /* close the CAN layer */ 1681 close_candev(ndev); 1682 return 0; 1683 } 1684 1685 static netdev_tx_t ican3_xmit(struct sk_buff *skb, struct net_device *ndev) 1686 { 1687 struct ican3_dev *mod = netdev_priv(ndev); 1688 struct can_frame *cf = (struct can_frame *)skb->data; 1689 struct ican3_fast_desc desc; 1690 void __iomem *desc_addr; 1691 unsigned long flags; 1692 1693 if (can_dropped_invalid_skb(ndev, skb)) 1694 return NETDEV_TX_OK; 1695 1696 spin_lock_irqsave(&mod->lock, flags); 1697 1698 /* check that we can actually transmit */ 1699 if (!ican3_txok(mod)) { 1700 netdev_err(mod->ndev, "BUG: no free descriptors\n"); 1701 spin_unlock_irqrestore(&mod->lock, flags); 1702 return NETDEV_TX_BUSY; 1703 } 1704 1705 /* copy the control bits of the descriptor */ 1706 ican3_set_page(mod, mod->fasttx_start + (mod->fasttx_num / 16)); 1707 desc_addr = mod->dpm + ((mod->fasttx_num % 16) * sizeof(desc)); 1708 memset(&desc, 0, sizeof(desc)); 1709 memcpy_fromio(&desc, desc_addr, 1); 1710 1711 /* convert the Linux CAN frame into ICAN3 format */ 1712 can_frame_to_ican3(mod, cf, &desc); 1713 1714 /* 1715 * This hardware doesn't have TX-done notifications, so we'll try and 1716 * emulate it the best we can using ECHO skbs. Add the skb to the ECHO 1717 * stack. Upon packet reception, check if the ECHO skb and received 1718 * skb match, and use that to wake the queue. 1719 */ 1720 ican3_put_echo_skb(mod, skb); 1721 1722 /* 1723 * the programming manual says that you must set the IVALID bit, then 1724 * interrupt, then set the valid bit. Quite weird, but it seems to be 1725 * required for this to work 1726 */ 1727 desc.control |= DESC_IVALID; 1728 memcpy_toio(desc_addr, &desc, sizeof(desc)); 1729 1730 /* generate a MODULbus interrupt to the microcontroller */ 1731 iowrite8(0x01, &mod->dpmctrl->interrupt); 1732 1733 desc.control ^= DESC_VALID; 1734 memcpy_toio(desc_addr, &desc, sizeof(desc)); 1735 1736 /* update the next buffer pointer */ 1737 mod->fasttx_num = (desc.control & DESC_WRAP) ? 0 1738 : (mod->fasttx_num + 1); 1739 1740 /* if there is no free descriptor space, stop the transmit queue */ 1741 if (!ican3_txok(mod)) 1742 netif_stop_queue(ndev); 1743 1744 spin_unlock_irqrestore(&mod->lock, flags); 1745 return NETDEV_TX_OK; 1746 } 1747 1748 static const struct net_device_ops ican3_netdev_ops = { 1749 .ndo_open = ican3_open, 1750 .ndo_stop = ican3_stop, 1751 .ndo_start_xmit = ican3_xmit, 1752 .ndo_change_mtu = can_change_mtu, 1753 }; 1754 1755 /* 1756 * Low-level CAN Device 1757 */ 1758 1759 /* This structure was stolen from drivers/net/can/sja1000/sja1000.c */ 1760 static const struct can_bittiming_const ican3_bittiming_const = { 1761 .name = DRV_NAME, 1762 .tseg1_min = 1, 1763 .tseg1_max = 16, 1764 .tseg2_min = 1, 1765 .tseg2_max = 8, 1766 .sjw_max = 4, 1767 .brp_min = 1, 1768 .brp_max = 64, 1769 .brp_inc = 1, 1770 }; 1771 1772 static int ican3_set_mode(struct net_device *ndev, enum can_mode mode) 1773 { 1774 struct ican3_dev *mod = netdev_priv(ndev); 1775 int ret; 1776 1777 if (mode != CAN_MODE_START) 1778 return -ENOTSUPP; 1779 1780 /* bring the bus online */ 1781 ret = ican3_set_bus_state(mod, true); 1782 if (ret) { 1783 netdev_err(ndev, "unable to set bus-on\n"); 1784 return ret; 1785 } 1786 1787 /* start up the network device */ 1788 mod->can.state = CAN_STATE_ERROR_ACTIVE; 1789 1790 if (netif_queue_stopped(ndev)) 1791 netif_wake_queue(ndev); 1792 1793 return 0; 1794 } 1795 1796 static int ican3_get_berr_counter(const struct net_device *ndev, 1797 struct can_berr_counter *bec) 1798 { 1799 struct ican3_dev *mod = netdev_priv(ndev); 1800 int ret; 1801 1802 ret = ican3_send_inquiry(mod, INQUIRY_STATUS); 1803 if (ret) 1804 return ret; 1805 1806 if (!wait_for_completion_timeout(&mod->buserror_comp, HZ)) { 1807 netdev_info(mod->ndev, "%s timed out\n", __func__); 1808 return -ETIMEDOUT; 1809 } 1810 1811 bec->rxerr = mod->bec.rxerr; 1812 bec->txerr = mod->bec.txerr; 1813 return 0; 1814 } 1815 1816 /* 1817 * Sysfs Attributes 1818 */ 1819 1820 static ssize_t termination_show(struct device *dev, 1821 struct device_attribute *attr, 1822 char *buf) 1823 { 1824 struct ican3_dev *mod = netdev_priv(to_net_dev(dev)); 1825 int ret; 1826 1827 ret = ican3_send_inquiry(mod, INQUIRY_TERMINATION); 1828 if (ret) 1829 return ret; 1830 1831 if (!wait_for_completion_timeout(&mod->termination_comp, HZ)) { 1832 netdev_info(mod->ndev, "%s timed out\n", __func__); 1833 return -ETIMEDOUT; 1834 } 1835 1836 return sysfs_emit(buf, "%u\n", mod->termination_enabled); 1837 } 1838 1839 static ssize_t termination_store(struct device *dev, 1840 struct device_attribute *attr, 1841 const char *buf, size_t count) 1842 { 1843 struct ican3_dev *mod = netdev_priv(to_net_dev(dev)); 1844 unsigned long enable; 1845 int ret; 1846 1847 if (kstrtoul(buf, 0, &enable)) 1848 return -EINVAL; 1849 1850 ret = ican3_set_termination(mod, enable); 1851 if (ret) 1852 return ret; 1853 1854 return count; 1855 } 1856 1857 static ssize_t fwinfo_show(struct device *dev, 1858 struct device_attribute *attr, 1859 char *buf) 1860 { 1861 struct ican3_dev *mod = netdev_priv(to_net_dev(dev)); 1862 1863 return scnprintf(buf, PAGE_SIZE, "%s\n", mod->fwinfo); 1864 } 1865 1866 static DEVICE_ATTR_RW(termination); 1867 static DEVICE_ATTR_RO(fwinfo); 1868 1869 static struct attribute *ican3_sysfs_attrs[] = { 1870 &dev_attr_termination.attr, 1871 &dev_attr_fwinfo.attr, 1872 NULL, 1873 }; 1874 1875 static const struct attribute_group ican3_sysfs_attr_group = { 1876 .attrs = ican3_sysfs_attrs, 1877 }; 1878 1879 /* 1880 * PCI Subsystem 1881 */ 1882 1883 static int ican3_probe(struct platform_device *pdev) 1884 { 1885 struct janz_platform_data *pdata; 1886 struct net_device *ndev; 1887 struct ican3_dev *mod; 1888 struct resource *res; 1889 struct device *dev; 1890 int ret; 1891 1892 pdata = dev_get_platdata(&pdev->dev); 1893 if (!pdata) 1894 return -ENXIO; 1895 1896 dev_dbg(&pdev->dev, "probe: module number %d\n", pdata->modno); 1897 1898 /* save the struct device for printing */ 1899 dev = &pdev->dev; 1900 1901 /* allocate the CAN device and private data */ 1902 ndev = alloc_candev(sizeof(*mod), 0); 1903 if (!ndev) { 1904 dev_err(dev, "unable to allocate CANdev\n"); 1905 ret = -ENOMEM; 1906 goto out_return; 1907 } 1908 1909 platform_set_drvdata(pdev, ndev); 1910 mod = netdev_priv(ndev); 1911 mod->ndev = ndev; 1912 mod->num = pdata->modno; 1913 netif_napi_add_weight(ndev, &mod->napi, ican3_napi, ICAN3_RX_BUFFERS); 1914 skb_queue_head_init(&mod->echoq); 1915 spin_lock_init(&mod->lock); 1916 init_completion(&mod->termination_comp); 1917 init_completion(&mod->buserror_comp); 1918 1919 /* setup device-specific sysfs attributes */ 1920 ndev->sysfs_groups[0] = &ican3_sysfs_attr_group; 1921 1922 /* the first unallocated page in the DPM is 9 */ 1923 mod->free_page = DPM_FREE_START; 1924 1925 ndev->netdev_ops = &ican3_netdev_ops; 1926 ndev->flags |= IFF_ECHO; 1927 SET_NETDEV_DEV(ndev, &pdev->dev); 1928 1929 mod->can.clock.freq = ICAN3_CAN_CLOCK; 1930 mod->can.bittiming_const = &ican3_bittiming_const; 1931 mod->can.do_set_mode = ican3_set_mode; 1932 mod->can.do_get_berr_counter = ican3_get_berr_counter; 1933 mod->can.ctrlmode_supported = CAN_CTRLMODE_3_SAMPLES 1934 | CAN_CTRLMODE_BERR_REPORTING 1935 | CAN_CTRLMODE_ONE_SHOT; 1936 1937 /* find our IRQ number */ 1938 mod->irq = platform_get_irq(pdev, 0); 1939 if (mod->irq < 0) { 1940 ret = -ENODEV; 1941 goto out_free_ndev; 1942 } 1943 1944 ndev->irq = mod->irq; 1945 1946 /* get access to the MODULbus registers for this module */ 1947 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1948 if (!res) { 1949 dev_err(dev, "MODULbus registers not found\n"); 1950 ret = -ENODEV; 1951 goto out_free_ndev; 1952 } 1953 1954 mod->dpm = ioremap(res->start, resource_size(res)); 1955 if (!mod->dpm) { 1956 dev_err(dev, "MODULbus registers not ioremap\n"); 1957 ret = -ENOMEM; 1958 goto out_free_ndev; 1959 } 1960 1961 mod->dpmctrl = mod->dpm + DPM_PAGE_SIZE; 1962 1963 /* get access to the control registers for this module */ 1964 res = platform_get_resource(pdev, IORESOURCE_MEM, 1); 1965 if (!res) { 1966 dev_err(dev, "CONTROL registers not found\n"); 1967 ret = -ENODEV; 1968 goto out_iounmap_dpm; 1969 } 1970 1971 mod->ctrl = ioremap(res->start, resource_size(res)); 1972 if (!mod->ctrl) { 1973 dev_err(dev, "CONTROL registers not ioremap\n"); 1974 ret = -ENOMEM; 1975 goto out_iounmap_dpm; 1976 } 1977 1978 /* disable our IRQ, then hookup the IRQ handler */ 1979 iowrite8(1 << mod->num, &mod->ctrl->int_disable); 1980 ret = request_irq(mod->irq, ican3_irq, IRQF_SHARED, DRV_NAME, mod); 1981 if (ret) { 1982 dev_err(dev, "unable to request IRQ\n"); 1983 goto out_iounmap_ctrl; 1984 } 1985 1986 /* reset and initialize the CAN controller into fast mode */ 1987 napi_enable(&mod->napi); 1988 ret = ican3_startup_module(mod); 1989 if (ret) { 1990 dev_err(dev, "%s: unable to start CANdev\n", __func__); 1991 goto out_free_irq; 1992 } 1993 1994 /* register with the Linux CAN layer */ 1995 ret = register_candev(ndev); 1996 if (ret) { 1997 dev_err(dev, "%s: unable to register CANdev\n", __func__); 1998 goto out_free_irq; 1999 } 2000 2001 netdev_info(mod->ndev, "module %d: registered CAN device\n", pdata->modno); 2002 return 0; 2003 2004 out_free_irq: 2005 napi_disable(&mod->napi); 2006 iowrite8(1 << mod->num, &mod->ctrl->int_disable); 2007 free_irq(mod->irq, mod); 2008 out_iounmap_ctrl: 2009 iounmap(mod->ctrl); 2010 out_iounmap_dpm: 2011 iounmap(mod->dpm); 2012 out_free_ndev: 2013 free_candev(ndev); 2014 out_return: 2015 return ret; 2016 } 2017 2018 static int ican3_remove(struct platform_device *pdev) 2019 { 2020 struct net_device *ndev = platform_get_drvdata(pdev); 2021 struct ican3_dev *mod = netdev_priv(ndev); 2022 2023 /* unregister the netdevice, stop interrupts */ 2024 unregister_netdev(ndev); 2025 napi_disable(&mod->napi); 2026 iowrite8(1 << mod->num, &mod->ctrl->int_disable); 2027 free_irq(mod->irq, mod); 2028 2029 /* put the module into reset */ 2030 ican3_shutdown_module(mod); 2031 2032 /* unmap all registers */ 2033 iounmap(mod->ctrl); 2034 iounmap(mod->dpm); 2035 2036 free_candev(ndev); 2037 2038 return 0; 2039 } 2040 2041 static struct platform_driver ican3_driver = { 2042 .driver = { 2043 .name = DRV_NAME, 2044 }, 2045 .probe = ican3_probe, 2046 .remove = ican3_remove, 2047 }; 2048 2049 module_platform_driver(ican3_driver); 2050 2051 MODULE_AUTHOR("Ira W. Snyder <iws@ovro.caltech.edu>"); 2052 MODULE_DESCRIPTION("Janz MODULbus VMOD-ICAN3 Driver"); 2053 MODULE_LICENSE("GPL"); 2054 MODULE_ALIAS("platform:janz-ican3"); 2055