1menu "CAN Device Drivers" 2 3config CAN_VCAN 4 tristate "Virtual Local CAN Interface (vcan)" 5 ---help--- 6 Similar to the network loopback devices, vcan offers a 7 virtual local CAN interface. 8 9 This driver can also be built as a module. If so, the module 10 will be called vcan. 11 12config CAN_SLCAN 13 tristate "Serial / USB serial CAN Adaptors (slcan)" 14 depends on TTY 15 ---help--- 16 CAN driver for several 'low cost' CAN interfaces that are attached 17 via serial lines or via USB-to-serial adapters using the LAWICEL 18 ASCII protocol. The driver implements the tty linediscipline N_SLCAN. 19 20 As only the sending and receiving of CAN frames is implemented, this 21 driver should work with the (serial/USB) CAN hardware from: 22 www.canusb.com / www.can232.com / www.mictronics.de / www.canhack.de 23 24 Userspace tools to attach the SLCAN line discipline (slcan_attach, 25 slcand) can be found in the can-utils at the SocketCAN SVN, see 26 http://developer.berlios.de/projects/socketcan for details. 27 28 The slcan driver supports up to 10 CAN netdevices by default which 29 can be changed by the 'maxdev=xx' module option. This driver can 30 also be built as a module. If so, the module will be called slcan. 31 32config CAN_DEV 33 tristate "Platform CAN drivers with Netlink support" 34 default y 35 ---help--- 36 Enables the common framework for platform CAN drivers with Netlink 37 support. This is the standard library for CAN drivers. 38 If unsure, say Y. 39 40if CAN_DEV 41 42config CAN_CALC_BITTIMING 43 bool "CAN bit-timing calculation" 44 default y 45 ---help--- 46 If enabled, CAN bit-timing parameters will be calculated for the 47 bit-rate specified via Netlink argument "bitrate" when the device 48 get started. This works fine for the most common CAN controllers 49 with standard bit-rates but may fail for exotic bit-rates or CAN 50 source clock frequencies. Disabling saves some space, but then the 51 bit-timing parameters must be specified directly using the Netlink 52 arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw". 53 If unsure, say Y. 54 55config CAN_LEDS 56 bool "Enable LED triggers for Netlink based drivers" 57 depends on LEDS_CLASS 58 select LEDS_TRIGGERS 59 ---help--- 60 This option adds two LED triggers for packet receive and transmit 61 events on each supported CAN device. 62 63 Say Y here if you are working on a system with led-class supported 64 LEDs and you want to use them as canbus activity indicators. 65 66config CAN_AT91 67 tristate "Atmel AT91 onchip CAN controller" 68 depends on (ARCH_AT91 || COMPILE_TEST) && HAS_IOMEM 69 ---help--- 70 This is a driver for the SoC CAN controller in Atmel's AT91SAM9263 71 and AT91SAM9X5 processors. 72 73config CAN_TI_HECC 74 depends on ARM 75 tristate "TI High End CAN Controller" 76 ---help--- 77 Driver for TI HECC (High End CAN Controller) module found on many 78 TI devices. The device specifications are available from www.ti.com 79 80config CAN_BFIN 81 depends on BF534 || BF536 || BF537 || BF538 || BF539 || BF54x 82 tristate "Analog Devices Blackfin on-chip CAN" 83 ---help--- 84 Driver for the Analog Devices Blackfin on-chip CAN controllers 85 86 To compile this driver as a module, choose M here: the 87 module will be called bfin_can. 88 89config CAN_JANZ_ICAN3 90 tristate "Janz VMOD-ICAN3 Intelligent CAN controller" 91 depends on MFD_JANZ_CMODIO 92 ---help--- 93 Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which 94 connects to a MODULbus carrier board. 95 96 This driver can also be built as a module. If so, the module will be 97 called janz-ican3.ko. 98 99config CAN_FLEXCAN 100 tristate "Support for Freescale FLEXCAN based chips" 101 depends on ARM || PPC 102 ---help--- 103 Say Y here if you want to support for Freescale FlexCAN. 104 105config PCH_CAN 106 tristate "Intel EG20T PCH CAN controller" 107 depends on PCI && (X86_32 || COMPILE_TEST) 108 ---help--- 109 This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which 110 is an IOH for x86 embedded processor (Intel Atom E6xx series). 111 This driver can access CAN bus. 112 113config CAN_GRCAN 114 tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices" 115 depends on OF && HAS_DMA 116 ---help--- 117 Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN. 118 Note that the driver supports little endian, even though little 119 endian syntheses of the cores would need some modifications on 120 the hardware level to work. 121 122config CAN_RCAR 123 tristate "Renesas R-Car CAN controller" 124 depends on ARM 125 ---help--- 126 Say Y here if you want to use CAN controller found on Renesas R-Car 127 SoCs. 128 129 To compile this driver as a module, choose M here: the module will 130 be called rcar_can. 131 132config CAN_XILINXCAN 133 tristate "Xilinx CAN" 134 depends on ARCH_ZYNQ || ARM64 || MICROBLAZE || COMPILE_TEST 135 depends on COMMON_CLK && HAS_IOMEM 136 ---help--- 137 Xilinx CAN driver. This driver supports both soft AXI CAN IP and 138 Zynq CANPS IP. 139 140source "drivers/net/can/mscan/Kconfig" 141 142source "drivers/net/can/sja1000/Kconfig" 143 144source "drivers/net/can/c_can/Kconfig" 145 146source "drivers/net/can/m_can/Kconfig" 147 148source "drivers/net/can/cc770/Kconfig" 149 150source "drivers/net/can/spi/Kconfig" 151 152source "drivers/net/can/usb/Kconfig" 153 154source "drivers/net/can/softing/Kconfig" 155 156endif 157 158config CAN_DEBUG_DEVICES 159 bool "CAN devices debugging messages" 160 ---help--- 161 Say Y here if you want the CAN device drivers to produce a bunch of 162 debug messages to the system log. Select this if you are having 163 a problem with CAN support and want to see more of what is going 164 on. 165 166endmenu 167