1menu "CAN Device Drivers" 2 3config CAN_VCAN 4 tristate "Virtual Local CAN Interface (vcan)" 5 ---help--- 6 Similar to the network loopback devices, vcan offers a 7 virtual local CAN interface. 8 9 This driver can also be built as a module. If so, the module 10 will be called vcan. 11 12config CAN_VXCAN 13 tristate "Virtual CAN Tunnel (vxcan)" 14 ---help--- 15 Similar to the virtual ethernet driver veth, vxcan implements a 16 local CAN traffic tunnel between two virtual CAN network devices. 17 When creating a vxcan, two vxcan devices are created as pair. 18 When one end receives the packet it appears on its pair and vice 19 versa. The vxcan can be used for cross namespace communication. 20 21 In opposite to vcan loopback devices the vxcan only forwards CAN 22 frames to its pair and does *not* provide a local echo of sent 23 CAN frames. To disable a potential echo in af_can.c the vxcan driver 24 announces IFF_ECHO in the interface flags. To have a clean start 25 in each namespace the CAN GW hop counter is set to zero. 26 27 This driver can also be built as a module. If so, the module 28 will be called vxcan. 29 30config CAN_SLCAN 31 tristate "Serial / USB serial CAN Adaptors (slcan)" 32 depends on TTY 33 ---help--- 34 CAN driver for several 'low cost' CAN interfaces that are attached 35 via serial lines or via USB-to-serial adapters using the LAWICEL 36 ASCII protocol. The driver implements the tty linediscipline N_SLCAN. 37 38 As only the sending and receiving of CAN frames is implemented, this 39 driver should work with the (serial/USB) CAN hardware from: 40 www.canusb.com / www.can232.com / www.mictronics.de / www.canhack.de 41 42 Userspace tools to attach the SLCAN line discipline (slcan_attach, 43 slcand) can be found in the can-utils at the SocketCAN SVN, see 44 http://developer.berlios.de/projects/socketcan for details. 45 46 The slcan driver supports up to 10 CAN netdevices by default which 47 can be changed by the 'maxdev=xx' module option. This driver can 48 also be built as a module. If so, the module will be called slcan. 49 50config CAN_DEV 51 tristate "Platform CAN drivers with Netlink support" 52 default y 53 ---help--- 54 Enables the common framework for platform CAN drivers with Netlink 55 support. This is the standard library for CAN drivers. 56 If unsure, say Y. 57 58if CAN_DEV 59 60config CAN_CALC_BITTIMING 61 bool "CAN bit-timing calculation" 62 default y 63 ---help--- 64 If enabled, CAN bit-timing parameters will be calculated for the 65 bit-rate specified via Netlink argument "bitrate" when the device 66 get started. This works fine for the most common CAN controllers 67 with standard bit-rates but may fail for exotic bit-rates or CAN 68 source clock frequencies. Disabling saves some space, but then the 69 bit-timing parameters must be specified directly using the Netlink 70 arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw". 71 If unsure, say Y. 72 73config CAN_LEDS 74 bool "Enable LED triggers for Netlink based drivers" 75 depends on LEDS_CLASS 76 select LEDS_TRIGGERS 77 ---help--- 78 This option adds two LED triggers for packet receive and transmit 79 events on each supported CAN device. 80 81 Say Y here if you are working on a system with led-class supported 82 LEDs and you want to use them as canbus activity indicators. 83 84config CAN_AT91 85 tristate "Atmel AT91 onchip CAN controller" 86 depends on (ARCH_AT91 || COMPILE_TEST) && HAS_IOMEM 87 ---help--- 88 This is a driver for the SoC CAN controller in Atmel's AT91SAM9263 89 and AT91SAM9X5 processors. 90 91config CAN_BFIN 92 depends on BF534 || BF536 || BF537 || BF538 || BF539 || BF54x 93 tristate "Analog Devices Blackfin on-chip CAN" 94 ---help--- 95 Driver for the Analog Devices Blackfin on-chip CAN controllers 96 97 To compile this driver as a module, choose M here: the 98 module will be called bfin_can. 99 100config CAN_FLEXCAN 101 tristate "Support for Freescale FLEXCAN based chips" 102 depends on ARM || PPC 103 ---help--- 104 Say Y here if you want to support for Freescale FlexCAN. 105 106config CAN_GRCAN 107 tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices" 108 depends on OF && HAS_DMA 109 ---help--- 110 Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN. 111 Note that the driver supports little endian, even though little 112 endian syntheses of the cores would need some modifications on 113 the hardware level to work. 114 115config CAN_JANZ_ICAN3 116 tristate "Janz VMOD-ICAN3 Intelligent CAN controller" 117 depends on MFD_JANZ_CMODIO 118 ---help--- 119 Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which 120 connects to a MODULbus carrier board. 121 122 This driver can also be built as a module. If so, the module will be 123 called janz-ican3.ko. 124 125config CAN_SUN4I 126 tristate "Allwinner A10 CAN controller" 127 depends on MACH_SUN4I || MACH_SUN7I || COMPILE_TEST 128 ---help--- 129 Say Y here if you want to use CAN controller found on Allwinner 130 A10/A20 SoCs. 131 132 To compile this driver as a module, choose M here: the module will 133 be called sun4i_can. 134 135config CAN_TI_HECC 136 depends on ARM 137 tristate "TI High End CAN Controller" 138 ---help--- 139 Driver for TI HECC (High End CAN Controller) module found on many 140 TI devices. The device specifications are available from www.ti.com 141 142config CAN_XILINXCAN 143 tristate "Xilinx CAN" 144 depends on ARCH_ZYNQ || ARM64 || MICROBLAZE || COMPILE_TEST 145 depends on COMMON_CLK && HAS_IOMEM 146 ---help--- 147 Xilinx CAN driver. This driver supports both soft AXI CAN IP and 148 Zynq CANPS IP. 149 150config PCH_CAN 151 tristate "Intel EG20T PCH CAN controller" 152 depends on PCI && (X86_32 || COMPILE_TEST) 153 ---help--- 154 This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which 155 is an IOH for x86 embedded processor (Intel Atom E6xx series). 156 This driver can access CAN bus. 157 158source "drivers/net/can/c_can/Kconfig" 159source "drivers/net/can/cc770/Kconfig" 160source "drivers/net/can/ifi_canfd/Kconfig" 161source "drivers/net/can/m_can/Kconfig" 162source "drivers/net/can/mscan/Kconfig" 163source "drivers/net/can/peak_canfd/Kconfig" 164source "drivers/net/can/rcar/Kconfig" 165source "drivers/net/can/sja1000/Kconfig" 166source "drivers/net/can/softing/Kconfig" 167source "drivers/net/can/spi/Kconfig" 168source "drivers/net/can/usb/Kconfig" 169 170endif 171 172config CAN_DEBUG_DEVICES 173 bool "CAN devices debugging messages" 174 ---help--- 175 Say Y here if you want the CAN device drivers to produce a bunch of 176 debug messages to the system log. Select this if you are having 177 a problem with CAN support and want to see more of what is going 178 on. 179 180endmenu 181