1# SPDX-License-Identifier: GPL-2.0-only 2 3menuconfig CAN_DEV 4 tristate "CAN Device Drivers" 5 default y 6 depends on CAN 7 help 8 Controller Area Network (CAN) is serial communications protocol up to 9 1Mbit/s for its original release (now known as Classical CAN) and up 10 to 8Mbit/s for the more recent CAN with Flexible Data-Rate 11 (CAN-FD). The CAN bus was originally mainly for automotive, but is now 12 widely used in marine (NMEA2000), industrial, and medical 13 applications. More information on the CAN network protocol family 14 PF_CAN is contained in <Documentation/networking/can.rst>. 15 16 This section contains all the CAN(-FD) device drivers including the 17 virtual ones. If you own such devices or plan to use the virtual CAN 18 interfaces to develop applications, say Y here. 19 20 To compile as a module, choose M here: the module will be called 21 can-dev. 22 23if CAN_DEV 24 25config CAN_VCAN 26 tristate "Virtual Local CAN Interface (vcan)" 27 help 28 Similar to the network loopback devices, vcan offers a 29 virtual local CAN interface. 30 31 This driver can also be built as a module. If so, the module 32 will be called vcan. 33 34config CAN_VXCAN 35 tristate "Virtual CAN Tunnel (vxcan)" 36 help 37 Similar to the virtual ethernet driver veth, vxcan implements a 38 local CAN traffic tunnel between two virtual CAN network devices. 39 When creating a vxcan, two vxcan devices are created as pair. 40 When one end receives the packet it appears on its pair and vice 41 versa. The vxcan can be used for cross namespace communication. 42 43 In opposite to vcan loopback devices the vxcan only forwards CAN 44 frames to its pair and does *not* provide a local echo of sent 45 CAN frames. To disable a potential echo in af_can.c the vxcan driver 46 announces IFF_ECHO in the interface flags. To have a clean start 47 in each namespace the CAN GW hop counter is set to zero. 48 49 This driver can also be built as a module. If so, the module 50 will be called vxcan. 51 52config CAN_NETLINK 53 bool "CAN device drivers with Netlink support" 54 default y 55 help 56 Enables the common framework for CAN device drivers. This is the 57 standard library and provides features for the Netlink interface such 58 as bittiming validation, support of CAN error states, device restart 59 and others. 60 61 The additional features selected by this option will be added to the 62 can-dev module. 63 64 This is required by all platform and hardware CAN drivers. If you 65 plan to use such devices or if unsure, say Y. 66 67if CAN_NETLINK 68 69config CAN_CALC_BITTIMING 70 bool "CAN bit-timing calculation" 71 default y 72 help 73 If enabled, CAN bit-timing parameters will be calculated for the 74 bit-rate specified via Netlink argument "bitrate" when the device 75 get started. This works fine for the most common CAN controllers 76 with standard bit-rates but may fail for exotic bit-rates or CAN 77 source clock frequencies. Disabling saves some space, but then the 78 bit-timing parameters must be specified directly using the Netlink 79 arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw". 80 81 The additional features selected by this option will be added to the 82 can-dev module. 83 84 If unsure, say Y. 85 86config CAN_RX_OFFLOAD 87 bool 88 89config CAN_AT91 90 tristate "Atmel AT91 onchip CAN controller" 91 depends on (ARCH_AT91 || COMPILE_TEST) && HAS_IOMEM 92 help 93 This is a driver for the SoC CAN controller in Atmel's AT91SAM9263 94 and AT91SAM9X5 processors. 95 96config CAN_CAN327 97 tristate "Serial / USB serial ELM327 based OBD-II Interfaces (can327)" 98 depends on TTY 99 select CAN_RX_OFFLOAD 100 help 101 CAN driver for several 'low cost' OBD-II interfaces based on the 102 ELM327 OBD-II interpreter chip. 103 104 This is a best effort driver - the ELM327 interface was never 105 designed to be used as a standalone CAN interface. However, it can 106 still be used for simple request-response protocols (such as OBD II), 107 and to monitor broadcast messages on a bus (such as in a vehicle). 108 109 Please refer to the documentation for information on how to use it: 110 Documentation/networking/device_drivers/can/can327.rst 111 112 If this driver is built as a module, it will be called can327. 113 114config CAN_FLEXCAN 115 tristate "Support for Freescale FLEXCAN based chips" 116 depends on OF || COLDFIRE || COMPILE_TEST 117 depends on HAS_IOMEM 118 select CAN_RX_OFFLOAD 119 help 120 Say Y here if you want to support for Freescale FlexCAN. 121 122config CAN_GRCAN 123 tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices" 124 depends on OF && HAS_DMA && HAS_IOMEM 125 help 126 Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN. 127 Note that the driver supports little endian, even though little 128 endian syntheses of the cores would need some modifications on 129 the hardware level to work. 130 131config CAN_JANZ_ICAN3 132 tristate "Janz VMOD-ICAN3 Intelligent CAN controller" 133 depends on MFD_JANZ_CMODIO 134 help 135 Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which 136 connects to a MODULbus carrier board. 137 138 This driver can also be built as a module. If so, the module will be 139 called janz-ican3.ko. 140 141config CAN_KVASER_PCIEFD 142 depends on PCI 143 tristate "Kvaser PCIe FD cards" 144 select CRC32 145 help 146 This is a driver for the Kvaser PCI Express CAN FD family. 147 148 Supported devices: 149 Kvaser PCIEcan 4xHS 150 Kvaser PCIEcan 2xHS v2 151 Kvaser PCIEcan HS v2 152 Kvaser Mini PCI Express HS v2 153 Kvaser Mini PCI Express 2xHS v2 154 155config CAN_SLCAN 156 tristate "Serial / USB serial CAN Adaptors (slcan)" 157 depends on TTY 158 help 159 CAN driver for several 'low cost' CAN interfaces that are attached 160 via serial lines or via USB-to-serial adapters using the LAWICEL 161 ASCII protocol. The driver implements the tty linediscipline N_SLCAN. 162 163 As only the sending and receiving of CAN frames is implemented, this 164 driver should work with the (serial/USB) CAN hardware from: 165 www.canusb.com / www.can232.com / www.mictronics.de / www.canhack.de 166 167 Userspace tools to attach the SLCAN line discipline (slcan_attach, 168 slcand) can be found in the can-utils at the linux-can project, see 169 https://github.com/linux-can/can-utils for details. 170 171 The slcan driver supports up to 10 CAN netdevices by default which 172 can be changed by the 'maxdev=xx' module option. This driver can 173 also be built as a module. If so, the module will be called slcan. 174 175config CAN_SUN4I 176 tristate "Allwinner A10 CAN controller" 177 depends on MACH_SUN4I || MACH_SUN7I || COMPILE_TEST 178 help 179 Say Y here if you want to use CAN controller found on Allwinner 180 A10/A20 SoCs. 181 182 To compile this driver as a module, choose M here: the module will 183 be called sun4i_can. 184 185config CAN_TI_HECC 186 depends on ARM 187 tristate "TI High End CAN Controller" 188 select CAN_RX_OFFLOAD 189 help 190 Driver for TI HECC (High End CAN Controller) module found on many 191 TI devices. The device specifications are available from www.ti.com 192 193config CAN_XILINXCAN 194 tristate "Xilinx CAN" 195 depends on ARCH_ZYNQ || ARM64 || MICROBLAZE || COMPILE_TEST 196 depends on COMMON_CLK && HAS_IOMEM 197 help 198 Xilinx CAN driver. This driver supports both soft AXI CAN IP and 199 Zynq CANPS IP. 200 201config PCH_CAN 202 tristate "Intel EG20T PCH CAN controller" 203 depends on PCI && (X86_32 || COMPILE_TEST) 204 help 205 This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which 206 is an IOH for x86 embedded processor (Intel Atom E6xx series). 207 This driver can access CAN bus. 208 209source "drivers/net/can/c_can/Kconfig" 210source "drivers/net/can/cc770/Kconfig" 211source "drivers/net/can/ctucanfd/Kconfig" 212source "drivers/net/can/ifi_canfd/Kconfig" 213source "drivers/net/can/m_can/Kconfig" 214source "drivers/net/can/mscan/Kconfig" 215source "drivers/net/can/peak_canfd/Kconfig" 216source "drivers/net/can/rcar/Kconfig" 217source "drivers/net/can/sja1000/Kconfig" 218source "drivers/net/can/softing/Kconfig" 219source "drivers/net/can/spi/Kconfig" 220source "drivers/net/can/usb/Kconfig" 221 222endif #CAN_NETLINK 223 224config CAN_DEBUG_DEVICES 225 bool "CAN devices debugging messages" 226 help 227 Say Y here if you want the CAN device drivers to produce a bunch of 228 debug messages to the system log. Select this if you are having 229 a problem with CAN support and want to see more of what is going 230 on. 231 232endif #CAN_DEV 233