1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Copyright (C) 2005, Intec Automation Inc. 4 * Copyright (C) 2014, Freescale Semiconductor, Inc. 5 */ 6 7 #include <linux/mtd/spi-nor.h> 8 9 #include "core.h" 10 11 #define SPINOR_OP_RD_ANY_REG 0x65 /* Read any register */ 12 #define SPINOR_OP_WR_ANY_REG 0x71 /* Write any register */ 13 #define SPINOR_REG_CYPRESS_CFR2V 0x00800003 14 #define SPINOR_REG_CYPRESS_CFR2V_MEMLAT_11_24 0xb 15 #define SPINOR_REG_CYPRESS_CFR3V 0x00800004 16 #define SPINOR_REG_CYPRESS_CFR3V_PGSZ BIT(4) /* Page size. */ 17 #define SPINOR_REG_CYPRESS_CFR5V 0x00800006 18 #define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN 0x3 19 #define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_DS 0 20 #define SPINOR_OP_CYPRESS_RD_FAST 0xee 21 22 /** 23 * spi_nor_cypress_octal_dtr_enable() - Enable octal DTR on Cypress flashes. 24 * @nor: pointer to a 'struct spi_nor' 25 * @enable: whether to enable or disable Octal DTR 26 * 27 * This also sets the memory access latency cycles to 24 to allow the flash to 28 * run at up to 200MHz. 29 * 30 * Return: 0 on success, -errno otherwise. 31 */ 32 static int spi_nor_cypress_octal_dtr_enable(struct spi_nor *nor, bool enable) 33 { 34 struct spi_mem_op op; 35 u8 *buf = nor->bouncebuf; 36 int ret; 37 38 if (enable) { 39 /* Use 24 dummy cycles for memory array reads. */ 40 ret = spi_nor_write_enable(nor); 41 if (ret) 42 return ret; 43 44 *buf = SPINOR_REG_CYPRESS_CFR2V_MEMLAT_11_24; 45 op = (struct spi_mem_op) 46 SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1), 47 SPI_MEM_OP_ADDR(3, SPINOR_REG_CYPRESS_CFR2V, 48 1), 49 SPI_MEM_OP_NO_DUMMY, 50 SPI_MEM_OP_DATA_OUT(1, buf, 1)); 51 52 ret = spi_mem_exec_op(nor->spimem, &op); 53 if (ret) 54 return ret; 55 56 ret = spi_nor_wait_till_ready(nor); 57 if (ret) 58 return ret; 59 60 nor->read_dummy = 24; 61 } 62 63 /* Set/unset the octal and DTR enable bits. */ 64 ret = spi_nor_write_enable(nor); 65 if (ret) 66 return ret; 67 68 if (enable) 69 *buf = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN; 70 else 71 *buf = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_DS; 72 73 op = (struct spi_mem_op) 74 SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1), 75 SPI_MEM_OP_ADDR(enable ? 3 : 4, 76 SPINOR_REG_CYPRESS_CFR5V, 77 1), 78 SPI_MEM_OP_NO_DUMMY, 79 SPI_MEM_OP_DATA_OUT(1, buf, 1)); 80 81 if (!enable) 82 spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR); 83 84 ret = spi_mem_exec_op(nor->spimem, &op); 85 if (ret) 86 return ret; 87 88 /* Read flash ID to make sure the switch was successful. */ 89 op = (struct spi_mem_op) 90 SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDID, 1), 91 SPI_MEM_OP_ADDR(enable ? 4 : 0, 0, 1), 92 SPI_MEM_OP_DUMMY(enable ? 3 : 0, 1), 93 SPI_MEM_OP_DATA_IN(round_up(nor->info->id_len, 2), 94 buf, 1)); 95 96 if (enable) 97 spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR); 98 99 ret = spi_mem_exec_op(nor->spimem, &op); 100 if (ret) 101 return ret; 102 103 if (memcmp(buf, nor->info->id, nor->info->id_len)) 104 return -EINVAL; 105 106 return 0; 107 } 108 109 static void s28hs512t_default_init(struct spi_nor *nor) 110 { 111 nor->params->octal_dtr_enable = spi_nor_cypress_octal_dtr_enable; 112 nor->params->writesize = 16; 113 } 114 115 static void s28hs512t_post_sfdp_fixup(struct spi_nor *nor) 116 { 117 /* 118 * On older versions of the flash the xSPI Profile 1.0 table has the 119 * 8D-8D-8D Fast Read opcode as 0x00. But it actually should be 0xEE. 120 */ 121 if (nor->params->reads[SNOR_CMD_READ_8_8_8_DTR].opcode == 0) 122 nor->params->reads[SNOR_CMD_READ_8_8_8_DTR].opcode = 123 SPINOR_OP_CYPRESS_RD_FAST; 124 125 /* This flash is also missing the 4-byte Page Program opcode bit. */ 126 spi_nor_set_pp_settings(&nor->params->page_programs[SNOR_CMD_PP], 127 SPINOR_OP_PP_4B, SNOR_PROTO_1_1_1); 128 /* 129 * Since xSPI Page Program opcode is backward compatible with 130 * Legacy SPI, use Legacy SPI opcode there as well. 131 */ 132 spi_nor_set_pp_settings(&nor->params->page_programs[SNOR_CMD_PP_8_8_8_DTR], 133 SPINOR_OP_PP_4B, SNOR_PROTO_8_8_8_DTR); 134 135 /* 136 * The xSPI Profile 1.0 table advertises the number of additional 137 * address bytes needed for Read Status Register command as 0 but the 138 * actual value for that is 4. 139 */ 140 nor->params->rdsr_addr_nbytes = 4; 141 } 142 143 static int s28hs512t_post_bfpt_fixup(struct spi_nor *nor, 144 const struct sfdp_parameter_header *bfpt_header, 145 const struct sfdp_bfpt *bfpt) 146 { 147 /* 148 * The BFPT table advertises a 512B page size but the page size is 149 * actually configurable (with the default being 256B). Read from 150 * CFR3V[4] and set the correct size. 151 */ 152 struct spi_mem_op op = 153 SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RD_ANY_REG, 1), 154 SPI_MEM_OP_ADDR(3, SPINOR_REG_CYPRESS_CFR3V, 1), 155 SPI_MEM_OP_NO_DUMMY, 156 SPI_MEM_OP_DATA_IN(1, nor->bouncebuf, 1)); 157 int ret; 158 159 ret = spi_mem_exec_op(nor->spimem, &op); 160 if (ret) 161 return ret; 162 163 if (nor->bouncebuf[0] & SPINOR_REG_CYPRESS_CFR3V_PGSZ) 164 nor->params->page_size = 512; 165 else 166 nor->params->page_size = 256; 167 168 return 0; 169 } 170 171 static struct spi_nor_fixups s28hs512t_fixups = { 172 .default_init = s28hs512t_default_init, 173 .post_sfdp = s28hs512t_post_sfdp_fixup, 174 .post_bfpt = s28hs512t_post_bfpt_fixup, 175 }; 176 177 static int 178 s25fs_s_post_bfpt_fixups(struct spi_nor *nor, 179 const struct sfdp_parameter_header *bfpt_header, 180 const struct sfdp_bfpt *bfpt) 181 { 182 /* 183 * The S25FS-S chip family reports 512-byte pages in BFPT but 184 * in reality the write buffer still wraps at the safe default 185 * of 256 bytes. Overwrite the page size advertised by BFPT 186 * to get the writes working. 187 */ 188 nor->params->page_size = 256; 189 190 return 0; 191 } 192 193 static struct spi_nor_fixups s25fs_s_fixups = { 194 .post_bfpt = s25fs_s_post_bfpt_fixups, 195 }; 196 197 static const struct flash_info spansion_parts[] = { 198 /* Spansion/Cypress -- single (large) sector size only, at least 199 * for the chips listed here (without boot sectors). 200 */ 201 { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, 202 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, 203 { "s25sl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, 204 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, 205 { "s25fl128s0", INFO6(0x012018, 0x4d0080, 256 * 1024, 64, 206 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | 207 USE_CLSR) }, 208 { "s25fl128s1", INFO6(0x012018, 0x4d0180, 64 * 1024, 256, 209 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | 210 USE_CLSR) }, 211 { "s25fl256s0", INFO6(0x010219, 0x4d0080, 256 * 1024, 128, 212 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | 213 USE_CLSR) }, 214 { "s25fl256s1", INFO6(0x010219, 0x4d0180, 64 * 1024, 512, 215 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | 216 USE_CLSR) }, 217 { "s25fl512s", INFO6(0x010220, 0x4d0080, 256 * 1024, 256, 218 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | 219 SPI_NOR_HAS_LOCK | USE_CLSR) }, 220 { "s25fs128s1", INFO6(0x012018, 0x4d0181, 64 * 1024, 256, 221 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) 222 .fixups = &s25fs_s_fixups, }, 223 { "s25fs256s0", INFO6(0x010219, 0x4d0081, 256 * 1024, 128, 224 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | 225 USE_CLSR) }, 226 { "s25fs256s1", INFO6(0x010219, 0x4d0181, 64 * 1024, 512, 227 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | 228 USE_CLSR) }, 229 { "s25fs512s", INFO6(0x010220, 0x4d0081, 256 * 1024, 256, 230 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) 231 .fixups = &s25fs_s_fixups, }, 232 { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) }, 233 { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) }, 234 { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, 235 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | 236 USE_CLSR) }, 237 { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, 238 SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | 239 USE_CLSR) }, 240 { "s25sl004a", INFO(0x010212, 0, 64 * 1024, 8, 0) }, 241 { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) }, 242 { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) }, 243 { "s25sl032a", INFO(0x010215, 0, 64 * 1024, 64, 0) }, 244 { "s25sl064a", INFO(0x010216, 0, 64 * 1024, 128, 0) }, 245 { "s25fl004k", INFO(0xef4013, 0, 64 * 1024, 8, 246 SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, 247 { "s25fl008k", INFO(0xef4014, 0, 64 * 1024, 16, 248 SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, 249 { "s25fl016k", INFO(0xef4015, 0, 64 * 1024, 32, 250 SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, 251 { "s25fl064k", INFO(0xef4017, 0, 64 * 1024, 128, 252 SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, 253 { "s25fl116k", INFO(0x014015, 0, 64 * 1024, 32, 254 SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, 255 { "s25fl132k", INFO(0x014016, 0, 64 * 1024, 64, SECT_4K) }, 256 { "s25fl164k", INFO(0x014017, 0, 64 * 1024, 128, SECT_4K) }, 257 { "s25fl204k", INFO(0x014013, 0, 64 * 1024, 8, 258 SECT_4K | SPI_NOR_DUAL_READ) }, 259 { "s25fl208k", INFO(0x014014, 0, 64 * 1024, 16, 260 SECT_4K | SPI_NOR_DUAL_READ) }, 261 { "s25fl064l", INFO(0x016017, 0, 64 * 1024, 128, 262 SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | 263 SPI_NOR_4B_OPCODES) }, 264 { "s25fl128l", INFO(0x016018, 0, 64 * 1024, 256, 265 SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | 266 SPI_NOR_4B_OPCODES) }, 267 { "s25fl256l", INFO(0x016019, 0, 64 * 1024, 512, 268 SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | 269 SPI_NOR_4B_OPCODES) }, 270 { "cy15x104q", INFO6(0x042cc2, 0x7f7f7f, 512 * 1024, 1, 271 SPI_NOR_NO_ERASE) }, 272 { "s28hs512t", INFO(0x345b1a, 0, 256 * 1024, 256, 273 SECT_4K | SPI_NOR_OCTAL_DTR_READ | 274 SPI_NOR_OCTAL_DTR_PP) 275 .fixups = &s28hs512t_fixups, 276 }, 277 }; 278 279 static void spansion_post_sfdp_fixups(struct spi_nor *nor) 280 { 281 if (nor->params->size <= SZ_16M) 282 return; 283 284 nor->flags |= SNOR_F_4B_OPCODES; 285 /* No small sector erase for 4-byte command set */ 286 nor->erase_opcode = SPINOR_OP_SE; 287 nor->mtd.erasesize = nor->info->sector_size; 288 } 289 290 static const struct spi_nor_fixups spansion_fixups = { 291 .post_sfdp = spansion_post_sfdp_fixups, 292 }; 293 294 const struct spi_nor_manufacturer spi_nor_spansion = { 295 .name = "spansion", 296 .parts = spansion_parts, 297 .nparts = ARRAY_SIZE(spansion_parts), 298 .fixups = &spansion_fixups, 299 }; 300