1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * NXP LPC32XX NAND SLC driver 4 * 5 * Authors: 6 * Kevin Wells <kevin.wells@nxp.com> 7 * Roland Stigge <stigge@antcom.de> 8 * 9 * Copyright © 2011 NXP Semiconductors 10 * Copyright © 2012 Roland Stigge 11 */ 12 13 #include <linux/slab.h> 14 #include <linux/module.h> 15 #include <linux/platform_device.h> 16 #include <linux/mtd/mtd.h> 17 #include <linux/mtd/rawnand.h> 18 #include <linux/mtd/partitions.h> 19 #include <linux/clk.h> 20 #include <linux/err.h> 21 #include <linux/delay.h> 22 #include <linux/io.h> 23 #include <linux/mm.h> 24 #include <linux/dma-mapping.h> 25 #include <linux/dmaengine.h> 26 #include <linux/mtd/nand_ecc.h> 27 #include <linux/gpio.h> 28 #include <linux/of.h> 29 #include <linux/of_gpio.h> 30 #include <linux/mtd/lpc32xx_slc.h> 31 32 #define LPC32XX_MODNAME "lpc32xx-nand" 33 34 /********************************************************************** 35 * SLC NAND controller register offsets 36 **********************************************************************/ 37 38 #define SLC_DATA(x) (x + 0x000) 39 #define SLC_ADDR(x) (x + 0x004) 40 #define SLC_CMD(x) (x + 0x008) 41 #define SLC_STOP(x) (x + 0x00C) 42 #define SLC_CTRL(x) (x + 0x010) 43 #define SLC_CFG(x) (x + 0x014) 44 #define SLC_STAT(x) (x + 0x018) 45 #define SLC_INT_STAT(x) (x + 0x01C) 46 #define SLC_IEN(x) (x + 0x020) 47 #define SLC_ISR(x) (x + 0x024) 48 #define SLC_ICR(x) (x + 0x028) 49 #define SLC_TAC(x) (x + 0x02C) 50 #define SLC_TC(x) (x + 0x030) 51 #define SLC_ECC(x) (x + 0x034) 52 #define SLC_DMA_DATA(x) (x + 0x038) 53 54 /********************************************************************** 55 * slc_ctrl register definitions 56 **********************************************************************/ 57 #define SLCCTRL_SW_RESET (1 << 2) /* Reset the NAND controller bit */ 58 #define SLCCTRL_ECC_CLEAR (1 << 1) /* Reset ECC bit */ 59 #define SLCCTRL_DMA_START (1 << 0) /* Start DMA channel bit */ 60 61 /********************************************************************** 62 * slc_cfg register definitions 63 **********************************************************************/ 64 #define SLCCFG_CE_LOW (1 << 5) /* Force CE low bit */ 65 #define SLCCFG_DMA_ECC (1 << 4) /* Enable DMA ECC bit */ 66 #define SLCCFG_ECC_EN (1 << 3) /* ECC enable bit */ 67 #define SLCCFG_DMA_BURST (1 << 2) /* DMA burst bit */ 68 #define SLCCFG_DMA_DIR (1 << 1) /* DMA write(0)/read(1) bit */ 69 #define SLCCFG_WIDTH (1 << 0) /* External device width, 0=8bit */ 70 71 /********************************************************************** 72 * slc_stat register definitions 73 **********************************************************************/ 74 #define SLCSTAT_DMA_FIFO (1 << 2) /* DMA FIFO has data bit */ 75 #define SLCSTAT_SLC_FIFO (1 << 1) /* SLC FIFO has data bit */ 76 #define SLCSTAT_NAND_READY (1 << 0) /* NAND device is ready bit */ 77 78 /********************************************************************** 79 * slc_int_stat, slc_ien, slc_isr, and slc_icr register definitions 80 **********************************************************************/ 81 #define SLCSTAT_INT_TC (1 << 1) /* Transfer count bit */ 82 #define SLCSTAT_INT_RDY_EN (1 << 0) /* Ready interrupt bit */ 83 84 /********************************************************************** 85 * slc_tac register definitions 86 **********************************************************************/ 87 /* Computation of clock cycles on basis of controller and device clock rates */ 88 #define SLCTAC_CLOCKS(c, n, s) (min_t(u32, DIV_ROUND_UP(c, n) - 1, 0xF) << s) 89 90 /* Clock setting for RDY write sample wait time in 2*n clocks */ 91 #define SLCTAC_WDR(n) (((n) & 0xF) << 28) 92 /* Write pulse width in clock cycles, 1 to 16 clocks */ 93 #define SLCTAC_WWIDTH(c, n) (SLCTAC_CLOCKS(c, n, 24)) 94 /* Write hold time of control and data signals, 1 to 16 clocks */ 95 #define SLCTAC_WHOLD(c, n) (SLCTAC_CLOCKS(c, n, 20)) 96 /* Write setup time of control and data signals, 1 to 16 clocks */ 97 #define SLCTAC_WSETUP(c, n) (SLCTAC_CLOCKS(c, n, 16)) 98 /* Clock setting for RDY read sample wait time in 2*n clocks */ 99 #define SLCTAC_RDR(n) (((n) & 0xF) << 12) 100 /* Read pulse width in clock cycles, 1 to 16 clocks */ 101 #define SLCTAC_RWIDTH(c, n) (SLCTAC_CLOCKS(c, n, 8)) 102 /* Read hold time of control and data signals, 1 to 16 clocks */ 103 #define SLCTAC_RHOLD(c, n) (SLCTAC_CLOCKS(c, n, 4)) 104 /* Read setup time of control and data signals, 1 to 16 clocks */ 105 #define SLCTAC_RSETUP(c, n) (SLCTAC_CLOCKS(c, n, 0)) 106 107 /********************************************************************** 108 * slc_ecc register definitions 109 **********************************************************************/ 110 /* ECC line party fetch macro */ 111 #define SLCECC_TO_LINEPAR(n) (((n) >> 6) & 0x7FFF) 112 #define SLCECC_TO_COLPAR(n) ((n) & 0x3F) 113 114 /* 115 * DMA requires storage space for the DMA local buffer and the hardware ECC 116 * storage area. The DMA local buffer is only used if DMA mapping fails 117 * during runtime. 118 */ 119 #define LPC32XX_DMA_DATA_SIZE 4096 120 #define LPC32XX_ECC_SAVE_SIZE ((4096 / 256) * 4) 121 122 /* Number of bytes used for ECC stored in NAND per 256 bytes */ 123 #define LPC32XX_SLC_DEV_ECC_BYTES 3 124 125 /* 126 * If the NAND base clock frequency can't be fetched, this frequency will be 127 * used instead as the base. This rate is used to setup the timing registers 128 * used for NAND accesses. 129 */ 130 #define LPC32XX_DEF_BUS_RATE 133250000 131 132 /* Milliseconds for DMA FIFO timeout (unlikely anyway) */ 133 #define LPC32XX_DMA_TIMEOUT 100 134 135 /* 136 * NAND ECC Layout for small page NAND devices 137 * Note: For large and huge page devices, the default layouts are used 138 */ 139 static int lpc32xx_ooblayout_ecc(struct mtd_info *mtd, int section, 140 struct mtd_oob_region *oobregion) 141 { 142 if (section) 143 return -ERANGE; 144 145 oobregion->length = 6; 146 oobregion->offset = 10; 147 148 return 0; 149 } 150 151 static int lpc32xx_ooblayout_free(struct mtd_info *mtd, int section, 152 struct mtd_oob_region *oobregion) 153 { 154 if (section > 1) 155 return -ERANGE; 156 157 if (!section) { 158 oobregion->offset = 0; 159 oobregion->length = 4; 160 } else { 161 oobregion->offset = 6; 162 oobregion->length = 4; 163 } 164 165 return 0; 166 } 167 168 static const struct mtd_ooblayout_ops lpc32xx_ooblayout_ops = { 169 .ecc = lpc32xx_ooblayout_ecc, 170 .free = lpc32xx_ooblayout_free, 171 }; 172 173 static u8 bbt_pattern[] = {'B', 'b', 't', '0' }; 174 static u8 mirror_pattern[] = {'1', 't', 'b', 'B' }; 175 176 /* 177 * Small page FLASH BBT descriptors, marker at offset 0, version at offset 6 178 * Note: Large page devices used the default layout 179 */ 180 static struct nand_bbt_descr bbt_smallpage_main_descr = { 181 .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE 182 | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP, 183 .offs = 0, 184 .len = 4, 185 .veroffs = 6, 186 .maxblocks = 4, 187 .pattern = bbt_pattern 188 }; 189 190 static struct nand_bbt_descr bbt_smallpage_mirror_descr = { 191 .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE 192 | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP, 193 .offs = 0, 194 .len = 4, 195 .veroffs = 6, 196 .maxblocks = 4, 197 .pattern = mirror_pattern 198 }; 199 200 /* 201 * NAND platform configuration structure 202 */ 203 struct lpc32xx_nand_cfg_slc { 204 uint32_t wdr_clks; 205 uint32_t wwidth; 206 uint32_t whold; 207 uint32_t wsetup; 208 uint32_t rdr_clks; 209 uint32_t rwidth; 210 uint32_t rhold; 211 uint32_t rsetup; 212 int wp_gpio; 213 struct mtd_partition *parts; 214 unsigned num_parts; 215 }; 216 217 struct lpc32xx_nand_host { 218 struct nand_chip nand_chip; 219 struct lpc32xx_slc_platform_data *pdata; 220 struct clk *clk; 221 void __iomem *io_base; 222 struct lpc32xx_nand_cfg_slc *ncfg; 223 224 struct completion comp; 225 struct dma_chan *dma_chan; 226 uint32_t dma_buf_len; 227 struct dma_slave_config dma_slave_config; 228 struct scatterlist sgl; 229 230 /* 231 * DMA and CPU addresses of ECC work area and data buffer 232 */ 233 uint32_t *ecc_buf; 234 uint8_t *data_buf; 235 dma_addr_t io_base_dma; 236 }; 237 238 static void lpc32xx_nand_setup(struct lpc32xx_nand_host *host) 239 { 240 uint32_t clkrate, tmp; 241 242 /* Reset SLC controller */ 243 writel(SLCCTRL_SW_RESET, SLC_CTRL(host->io_base)); 244 udelay(1000); 245 246 /* Basic setup */ 247 writel(0, SLC_CFG(host->io_base)); 248 writel(0, SLC_IEN(host->io_base)); 249 writel((SLCSTAT_INT_TC | SLCSTAT_INT_RDY_EN), 250 SLC_ICR(host->io_base)); 251 252 /* Get base clock for SLC block */ 253 clkrate = clk_get_rate(host->clk); 254 if (clkrate == 0) 255 clkrate = LPC32XX_DEF_BUS_RATE; 256 257 /* Compute clock setup values */ 258 tmp = SLCTAC_WDR(host->ncfg->wdr_clks) | 259 SLCTAC_WWIDTH(clkrate, host->ncfg->wwidth) | 260 SLCTAC_WHOLD(clkrate, host->ncfg->whold) | 261 SLCTAC_WSETUP(clkrate, host->ncfg->wsetup) | 262 SLCTAC_RDR(host->ncfg->rdr_clks) | 263 SLCTAC_RWIDTH(clkrate, host->ncfg->rwidth) | 264 SLCTAC_RHOLD(clkrate, host->ncfg->rhold) | 265 SLCTAC_RSETUP(clkrate, host->ncfg->rsetup); 266 writel(tmp, SLC_TAC(host->io_base)); 267 } 268 269 /* 270 * Hardware specific access to control lines 271 */ 272 static void lpc32xx_nand_cmd_ctrl(struct nand_chip *chip, int cmd, 273 unsigned int ctrl) 274 { 275 uint32_t tmp; 276 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 277 278 /* Does CE state need to be changed? */ 279 tmp = readl(SLC_CFG(host->io_base)); 280 if (ctrl & NAND_NCE) 281 tmp |= SLCCFG_CE_LOW; 282 else 283 tmp &= ~SLCCFG_CE_LOW; 284 writel(tmp, SLC_CFG(host->io_base)); 285 286 if (cmd != NAND_CMD_NONE) { 287 if (ctrl & NAND_CLE) 288 writel(cmd, SLC_CMD(host->io_base)); 289 else 290 writel(cmd, SLC_ADDR(host->io_base)); 291 } 292 } 293 294 /* 295 * Read the Device Ready pin 296 */ 297 static int lpc32xx_nand_device_ready(struct nand_chip *chip) 298 { 299 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 300 int rdy = 0; 301 302 if ((readl(SLC_STAT(host->io_base)) & SLCSTAT_NAND_READY) != 0) 303 rdy = 1; 304 305 return rdy; 306 } 307 308 /* 309 * Enable NAND write protect 310 */ 311 static void lpc32xx_wp_enable(struct lpc32xx_nand_host *host) 312 { 313 if (gpio_is_valid(host->ncfg->wp_gpio)) 314 gpio_set_value(host->ncfg->wp_gpio, 0); 315 } 316 317 /* 318 * Disable NAND write protect 319 */ 320 static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host) 321 { 322 if (gpio_is_valid(host->ncfg->wp_gpio)) 323 gpio_set_value(host->ncfg->wp_gpio, 1); 324 } 325 326 /* 327 * Prepares SLC for transfers with H/W ECC enabled 328 */ 329 static void lpc32xx_nand_ecc_enable(struct nand_chip *chip, int mode) 330 { 331 /* Hardware ECC is enabled automatically in hardware as needed */ 332 } 333 334 /* 335 * Calculates the ECC for the data 336 */ 337 static int lpc32xx_nand_ecc_calculate(struct nand_chip *chip, 338 const unsigned char *buf, 339 unsigned char *code) 340 { 341 /* 342 * ECC is calculated automatically in hardware during syndrome read 343 * and write operations, so it doesn't need to be calculated here. 344 */ 345 return 0; 346 } 347 348 /* 349 * Read a single byte from NAND device 350 */ 351 static uint8_t lpc32xx_nand_read_byte(struct nand_chip *chip) 352 { 353 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 354 355 return (uint8_t)readl(SLC_DATA(host->io_base)); 356 } 357 358 /* 359 * Simple device read without ECC 360 */ 361 static void lpc32xx_nand_read_buf(struct nand_chip *chip, u_char *buf, int len) 362 { 363 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 364 365 /* Direct device read with no ECC */ 366 while (len-- > 0) 367 *buf++ = (uint8_t)readl(SLC_DATA(host->io_base)); 368 } 369 370 /* 371 * Simple device write without ECC 372 */ 373 static void lpc32xx_nand_write_buf(struct nand_chip *chip, const uint8_t *buf, 374 int len) 375 { 376 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 377 378 /* Direct device write with no ECC */ 379 while (len-- > 0) 380 writel((uint32_t)*buf++, SLC_DATA(host->io_base)); 381 } 382 383 /* 384 * Read the OOB data from the device without ECC using FIFO method 385 */ 386 static int lpc32xx_nand_read_oob_syndrome(struct nand_chip *chip, int page) 387 { 388 struct mtd_info *mtd = nand_to_mtd(chip); 389 390 return nand_read_oob_op(chip, page, 0, chip->oob_poi, mtd->oobsize); 391 } 392 393 /* 394 * Write the OOB data to the device without ECC using FIFO method 395 */ 396 static int lpc32xx_nand_write_oob_syndrome(struct nand_chip *chip, int page) 397 { 398 struct mtd_info *mtd = nand_to_mtd(chip); 399 400 return nand_prog_page_op(chip, page, mtd->writesize, chip->oob_poi, 401 mtd->oobsize); 402 } 403 404 /* 405 * Fills in the ECC fields in the OOB buffer with the hardware generated ECC 406 */ 407 static void lpc32xx_slc_ecc_copy(uint8_t *spare, const uint32_t *ecc, int count) 408 { 409 int i; 410 411 for (i = 0; i < (count * 3); i += 3) { 412 uint32_t ce = ecc[i / 3]; 413 ce = ~(ce << 2) & 0xFFFFFF; 414 spare[i + 2] = (uint8_t)(ce & 0xFF); 415 ce >>= 8; 416 spare[i + 1] = (uint8_t)(ce & 0xFF); 417 ce >>= 8; 418 spare[i] = (uint8_t)(ce & 0xFF); 419 } 420 } 421 422 static void lpc32xx_dma_complete_func(void *completion) 423 { 424 complete(completion); 425 } 426 427 static int lpc32xx_xmit_dma(struct mtd_info *mtd, dma_addr_t dma, 428 void *mem, int len, enum dma_transfer_direction dir) 429 { 430 struct nand_chip *chip = mtd_to_nand(mtd); 431 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 432 struct dma_async_tx_descriptor *desc; 433 int flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT; 434 int res; 435 436 host->dma_slave_config.direction = dir; 437 host->dma_slave_config.src_addr = dma; 438 host->dma_slave_config.dst_addr = dma; 439 host->dma_slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; 440 host->dma_slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; 441 host->dma_slave_config.src_maxburst = 4; 442 host->dma_slave_config.dst_maxburst = 4; 443 /* DMA controller does flow control: */ 444 host->dma_slave_config.device_fc = false; 445 if (dmaengine_slave_config(host->dma_chan, &host->dma_slave_config)) { 446 dev_err(mtd->dev.parent, "Failed to setup DMA slave\n"); 447 return -ENXIO; 448 } 449 450 sg_init_one(&host->sgl, mem, len); 451 452 res = dma_map_sg(host->dma_chan->device->dev, &host->sgl, 1, 453 DMA_BIDIRECTIONAL); 454 if (res != 1) { 455 dev_err(mtd->dev.parent, "Failed to map sg list\n"); 456 return -ENXIO; 457 } 458 desc = dmaengine_prep_slave_sg(host->dma_chan, &host->sgl, 1, dir, 459 flags); 460 if (!desc) { 461 dev_err(mtd->dev.parent, "Failed to prepare slave sg\n"); 462 goto out1; 463 } 464 465 init_completion(&host->comp); 466 desc->callback = lpc32xx_dma_complete_func; 467 desc->callback_param = &host->comp; 468 469 dmaengine_submit(desc); 470 dma_async_issue_pending(host->dma_chan); 471 472 wait_for_completion_timeout(&host->comp, msecs_to_jiffies(1000)); 473 474 dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1, 475 DMA_BIDIRECTIONAL); 476 477 return 0; 478 out1: 479 dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1, 480 DMA_BIDIRECTIONAL); 481 return -ENXIO; 482 } 483 484 /* 485 * DMA read/write transfers with ECC support 486 */ 487 static int lpc32xx_xfer(struct mtd_info *mtd, uint8_t *buf, int eccsubpages, 488 int read) 489 { 490 struct nand_chip *chip = mtd_to_nand(mtd); 491 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 492 int i, status = 0; 493 unsigned long timeout; 494 int res; 495 enum dma_transfer_direction dir = 496 read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV; 497 uint8_t *dma_buf; 498 bool dma_mapped; 499 500 if ((void *)buf <= high_memory) { 501 dma_buf = buf; 502 dma_mapped = true; 503 } else { 504 dma_buf = host->data_buf; 505 dma_mapped = false; 506 if (!read) 507 memcpy(host->data_buf, buf, mtd->writesize); 508 } 509 510 if (read) { 511 writel(readl(SLC_CFG(host->io_base)) | 512 SLCCFG_DMA_DIR | SLCCFG_ECC_EN | SLCCFG_DMA_ECC | 513 SLCCFG_DMA_BURST, SLC_CFG(host->io_base)); 514 } else { 515 writel((readl(SLC_CFG(host->io_base)) | 516 SLCCFG_ECC_EN | SLCCFG_DMA_ECC | SLCCFG_DMA_BURST) & 517 ~SLCCFG_DMA_DIR, 518 SLC_CFG(host->io_base)); 519 } 520 521 /* Clear initial ECC */ 522 writel(SLCCTRL_ECC_CLEAR, SLC_CTRL(host->io_base)); 523 524 /* Transfer size is data area only */ 525 writel(mtd->writesize, SLC_TC(host->io_base)); 526 527 /* Start transfer in the NAND controller */ 528 writel(readl(SLC_CTRL(host->io_base)) | SLCCTRL_DMA_START, 529 SLC_CTRL(host->io_base)); 530 531 for (i = 0; i < chip->ecc.steps; i++) { 532 /* Data */ 533 res = lpc32xx_xmit_dma(mtd, SLC_DMA_DATA(host->io_base_dma), 534 dma_buf + i * chip->ecc.size, 535 mtd->writesize / chip->ecc.steps, dir); 536 if (res) 537 return res; 538 539 /* Always _read_ ECC */ 540 if (i == chip->ecc.steps - 1) 541 break; 542 if (!read) /* ECC availability delayed on write */ 543 udelay(10); 544 res = lpc32xx_xmit_dma(mtd, SLC_ECC(host->io_base_dma), 545 &host->ecc_buf[i], 4, DMA_DEV_TO_MEM); 546 if (res) 547 return res; 548 } 549 550 /* 551 * According to NXP, the DMA can be finished here, but the NAND 552 * controller may still have buffered data. After porting to using the 553 * dmaengine DMA driver (amba-pl080), the condition (DMA_FIFO empty) 554 * appears to be always true, according to tests. Keeping the check for 555 * safety reasons for now. 556 */ 557 if (readl(SLC_STAT(host->io_base)) & SLCSTAT_DMA_FIFO) { 558 dev_warn(mtd->dev.parent, "FIFO not empty!\n"); 559 timeout = jiffies + msecs_to_jiffies(LPC32XX_DMA_TIMEOUT); 560 while ((readl(SLC_STAT(host->io_base)) & SLCSTAT_DMA_FIFO) && 561 time_before(jiffies, timeout)) 562 cpu_relax(); 563 if (!time_before(jiffies, timeout)) { 564 dev_err(mtd->dev.parent, "FIFO held data too long\n"); 565 status = -EIO; 566 } 567 } 568 569 /* Read last calculated ECC value */ 570 if (!read) 571 udelay(10); 572 host->ecc_buf[chip->ecc.steps - 1] = 573 readl(SLC_ECC(host->io_base)); 574 575 /* Flush DMA */ 576 dmaengine_terminate_all(host->dma_chan); 577 578 if (readl(SLC_STAT(host->io_base)) & SLCSTAT_DMA_FIFO || 579 readl(SLC_TC(host->io_base))) { 580 /* Something is left in the FIFO, something is wrong */ 581 dev_err(mtd->dev.parent, "DMA FIFO failure\n"); 582 status = -EIO; 583 } 584 585 /* Stop DMA & HW ECC */ 586 writel(readl(SLC_CTRL(host->io_base)) & ~SLCCTRL_DMA_START, 587 SLC_CTRL(host->io_base)); 588 writel(readl(SLC_CFG(host->io_base)) & 589 ~(SLCCFG_DMA_DIR | SLCCFG_ECC_EN | SLCCFG_DMA_ECC | 590 SLCCFG_DMA_BURST), SLC_CFG(host->io_base)); 591 592 if (!dma_mapped && read) 593 memcpy(buf, host->data_buf, mtd->writesize); 594 595 return status; 596 } 597 598 /* 599 * Read the data and OOB data from the device, use ECC correction with the 600 * data, disable ECC for the OOB data 601 */ 602 static int lpc32xx_nand_read_page_syndrome(struct nand_chip *chip, uint8_t *buf, 603 int oob_required, int page) 604 { 605 struct mtd_info *mtd = nand_to_mtd(chip); 606 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 607 struct mtd_oob_region oobregion = { }; 608 int stat, i, status, error; 609 uint8_t *oobecc, tmpecc[LPC32XX_ECC_SAVE_SIZE]; 610 611 /* Issue read command */ 612 nand_read_page_op(chip, page, 0, NULL, 0); 613 614 /* Read data and oob, calculate ECC */ 615 status = lpc32xx_xfer(mtd, buf, chip->ecc.steps, 1); 616 617 /* Get OOB data */ 618 chip->legacy.read_buf(chip, chip->oob_poi, mtd->oobsize); 619 620 /* Convert to stored ECC format */ 621 lpc32xx_slc_ecc_copy(tmpecc, (uint32_t *) host->ecc_buf, chip->ecc.steps); 622 623 /* Pointer to ECC data retrieved from NAND spare area */ 624 error = mtd_ooblayout_ecc(mtd, 0, &oobregion); 625 if (error) 626 return error; 627 628 oobecc = chip->oob_poi + oobregion.offset; 629 630 for (i = 0; i < chip->ecc.steps; i++) { 631 stat = chip->ecc.correct(chip, buf, oobecc, 632 &tmpecc[i * chip->ecc.bytes]); 633 if (stat < 0) 634 mtd->ecc_stats.failed++; 635 else 636 mtd->ecc_stats.corrected += stat; 637 638 buf += chip->ecc.size; 639 oobecc += chip->ecc.bytes; 640 } 641 642 return status; 643 } 644 645 /* 646 * Read the data and OOB data from the device, no ECC correction with the 647 * data or OOB data 648 */ 649 static int lpc32xx_nand_read_page_raw_syndrome(struct nand_chip *chip, 650 uint8_t *buf, int oob_required, 651 int page) 652 { 653 struct mtd_info *mtd = nand_to_mtd(chip); 654 655 /* Issue read command */ 656 nand_read_page_op(chip, page, 0, NULL, 0); 657 658 /* Raw reads can just use the FIFO interface */ 659 chip->legacy.read_buf(chip, buf, chip->ecc.size * chip->ecc.steps); 660 chip->legacy.read_buf(chip, chip->oob_poi, mtd->oobsize); 661 662 return 0; 663 } 664 665 /* 666 * Write the data and OOB data to the device, use ECC with the data, 667 * disable ECC for the OOB data 668 */ 669 static int lpc32xx_nand_write_page_syndrome(struct nand_chip *chip, 670 const uint8_t *buf, 671 int oob_required, int page) 672 { 673 struct mtd_info *mtd = nand_to_mtd(chip); 674 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 675 struct mtd_oob_region oobregion = { }; 676 uint8_t *pb; 677 int error; 678 679 nand_prog_page_begin_op(chip, page, 0, NULL, 0); 680 681 /* Write data, calculate ECC on outbound data */ 682 error = lpc32xx_xfer(mtd, (uint8_t *)buf, chip->ecc.steps, 0); 683 if (error) 684 return error; 685 686 /* 687 * The calculated ECC needs some manual work done to it before 688 * committing it to NAND. Process the calculated ECC and place 689 * the resultant values directly into the OOB buffer. */ 690 error = mtd_ooblayout_ecc(mtd, 0, &oobregion); 691 if (error) 692 return error; 693 694 pb = chip->oob_poi + oobregion.offset; 695 lpc32xx_slc_ecc_copy(pb, (uint32_t *)host->ecc_buf, chip->ecc.steps); 696 697 /* Write ECC data to device */ 698 chip->legacy.write_buf(chip, chip->oob_poi, mtd->oobsize); 699 700 return nand_prog_page_end_op(chip); 701 } 702 703 /* 704 * Write the data and OOB data to the device, no ECC correction with the 705 * data or OOB data 706 */ 707 static int lpc32xx_nand_write_page_raw_syndrome(struct nand_chip *chip, 708 const uint8_t *buf, 709 int oob_required, int page) 710 { 711 struct mtd_info *mtd = nand_to_mtd(chip); 712 713 /* Raw writes can just use the FIFO interface */ 714 nand_prog_page_begin_op(chip, page, 0, buf, 715 chip->ecc.size * chip->ecc.steps); 716 chip->legacy.write_buf(chip, chip->oob_poi, mtd->oobsize); 717 718 return nand_prog_page_end_op(chip); 719 } 720 721 static int lpc32xx_nand_dma_setup(struct lpc32xx_nand_host *host) 722 { 723 struct mtd_info *mtd = nand_to_mtd(&host->nand_chip); 724 dma_cap_mask_t mask; 725 726 if (!host->pdata || !host->pdata->dma_filter) { 727 dev_err(mtd->dev.parent, "no DMA platform data\n"); 728 return -ENOENT; 729 } 730 731 dma_cap_zero(mask); 732 dma_cap_set(DMA_SLAVE, mask); 733 host->dma_chan = dma_request_channel(mask, host->pdata->dma_filter, 734 "nand-slc"); 735 if (!host->dma_chan) { 736 dev_err(mtd->dev.parent, "Failed to request DMA channel\n"); 737 return -EBUSY; 738 } 739 740 return 0; 741 } 742 743 static struct lpc32xx_nand_cfg_slc *lpc32xx_parse_dt(struct device *dev) 744 { 745 struct lpc32xx_nand_cfg_slc *ncfg; 746 struct device_node *np = dev->of_node; 747 748 ncfg = devm_kzalloc(dev, sizeof(*ncfg), GFP_KERNEL); 749 if (!ncfg) 750 return NULL; 751 752 of_property_read_u32(np, "nxp,wdr-clks", &ncfg->wdr_clks); 753 of_property_read_u32(np, "nxp,wwidth", &ncfg->wwidth); 754 of_property_read_u32(np, "nxp,whold", &ncfg->whold); 755 of_property_read_u32(np, "nxp,wsetup", &ncfg->wsetup); 756 of_property_read_u32(np, "nxp,rdr-clks", &ncfg->rdr_clks); 757 of_property_read_u32(np, "nxp,rwidth", &ncfg->rwidth); 758 of_property_read_u32(np, "nxp,rhold", &ncfg->rhold); 759 of_property_read_u32(np, "nxp,rsetup", &ncfg->rsetup); 760 761 if (!ncfg->wdr_clks || !ncfg->wwidth || !ncfg->whold || 762 !ncfg->wsetup || !ncfg->rdr_clks || !ncfg->rwidth || 763 !ncfg->rhold || !ncfg->rsetup) { 764 dev_err(dev, "chip parameters not specified correctly\n"); 765 return NULL; 766 } 767 768 ncfg->wp_gpio = of_get_named_gpio(np, "gpios", 0); 769 770 return ncfg; 771 } 772 773 static int lpc32xx_nand_attach_chip(struct nand_chip *chip) 774 { 775 struct mtd_info *mtd = nand_to_mtd(chip); 776 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 777 778 /* OOB and ECC CPU and DMA work areas */ 779 host->ecc_buf = (uint32_t *)(host->data_buf + LPC32XX_DMA_DATA_SIZE); 780 781 /* 782 * Small page FLASH has a unique OOB layout, but large and huge 783 * page FLASH use the standard layout. Small page FLASH uses a 784 * custom BBT marker layout. 785 */ 786 if (mtd->writesize <= 512) 787 mtd_set_ooblayout(mtd, &lpc32xx_ooblayout_ops); 788 789 /* These sizes remain the same regardless of page size */ 790 chip->ecc.size = 256; 791 chip->ecc.bytes = LPC32XX_SLC_DEV_ECC_BYTES; 792 chip->ecc.prepad = 0; 793 chip->ecc.postpad = 0; 794 795 /* 796 * Use a custom BBT marker setup for small page FLASH that 797 * won't interfere with the ECC layout. Large and huge page 798 * FLASH use the standard layout. 799 */ 800 if ((chip->bbt_options & NAND_BBT_USE_FLASH) && 801 mtd->writesize <= 512) { 802 chip->bbt_td = &bbt_smallpage_main_descr; 803 chip->bbt_md = &bbt_smallpage_mirror_descr; 804 } 805 806 return 0; 807 } 808 809 static const struct nand_controller_ops lpc32xx_nand_controller_ops = { 810 .attach_chip = lpc32xx_nand_attach_chip, 811 }; 812 813 /* 814 * Probe for NAND controller 815 */ 816 static int lpc32xx_nand_probe(struct platform_device *pdev) 817 { 818 struct lpc32xx_nand_host *host; 819 struct mtd_info *mtd; 820 struct nand_chip *chip; 821 struct resource *rc; 822 int res; 823 824 /* Allocate memory for the device structure (and zero it) */ 825 host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL); 826 if (!host) 827 return -ENOMEM; 828 829 rc = platform_get_resource(pdev, IORESOURCE_MEM, 0); 830 host->io_base = devm_ioremap_resource(&pdev->dev, rc); 831 if (IS_ERR(host->io_base)) 832 return PTR_ERR(host->io_base); 833 834 host->io_base_dma = rc->start; 835 if (pdev->dev.of_node) 836 host->ncfg = lpc32xx_parse_dt(&pdev->dev); 837 if (!host->ncfg) { 838 dev_err(&pdev->dev, 839 "Missing or bad NAND config from device tree\n"); 840 return -ENOENT; 841 } 842 if (host->ncfg->wp_gpio == -EPROBE_DEFER) 843 return -EPROBE_DEFER; 844 if (gpio_is_valid(host->ncfg->wp_gpio) && devm_gpio_request(&pdev->dev, 845 host->ncfg->wp_gpio, "NAND WP")) { 846 dev_err(&pdev->dev, "GPIO not available\n"); 847 return -EBUSY; 848 } 849 lpc32xx_wp_disable(host); 850 851 host->pdata = dev_get_platdata(&pdev->dev); 852 853 chip = &host->nand_chip; 854 mtd = nand_to_mtd(chip); 855 nand_set_controller_data(chip, host); 856 nand_set_flash_node(chip, pdev->dev.of_node); 857 mtd->owner = THIS_MODULE; 858 mtd->dev.parent = &pdev->dev; 859 860 /* Get NAND clock */ 861 host->clk = devm_clk_get(&pdev->dev, NULL); 862 if (IS_ERR(host->clk)) { 863 dev_err(&pdev->dev, "Clock failure\n"); 864 res = -ENOENT; 865 goto enable_wp; 866 } 867 res = clk_prepare_enable(host->clk); 868 if (res) 869 goto enable_wp; 870 871 /* Set NAND IO addresses and command/ready functions */ 872 chip->legacy.IO_ADDR_R = SLC_DATA(host->io_base); 873 chip->legacy.IO_ADDR_W = SLC_DATA(host->io_base); 874 chip->legacy.cmd_ctrl = lpc32xx_nand_cmd_ctrl; 875 chip->legacy.dev_ready = lpc32xx_nand_device_ready; 876 chip->legacy.chip_delay = 20; /* 20us command delay time */ 877 878 /* Init NAND controller */ 879 lpc32xx_nand_setup(host); 880 881 platform_set_drvdata(pdev, host); 882 883 /* NAND callbacks for LPC32xx SLC hardware */ 884 chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_ON_HOST; 885 chip->ecc.placement = NAND_ECC_PLACEMENT_INTERLEAVED; 886 chip->legacy.read_byte = lpc32xx_nand_read_byte; 887 chip->legacy.read_buf = lpc32xx_nand_read_buf; 888 chip->legacy.write_buf = lpc32xx_nand_write_buf; 889 chip->ecc.read_page_raw = lpc32xx_nand_read_page_raw_syndrome; 890 chip->ecc.read_page = lpc32xx_nand_read_page_syndrome; 891 chip->ecc.write_page_raw = lpc32xx_nand_write_page_raw_syndrome; 892 chip->ecc.write_page = lpc32xx_nand_write_page_syndrome; 893 chip->ecc.write_oob = lpc32xx_nand_write_oob_syndrome; 894 chip->ecc.read_oob = lpc32xx_nand_read_oob_syndrome; 895 chip->ecc.calculate = lpc32xx_nand_ecc_calculate; 896 chip->ecc.correct = nand_correct_data; 897 chip->ecc.strength = 1; 898 chip->ecc.hwctl = lpc32xx_nand_ecc_enable; 899 900 /* 901 * Allocate a large enough buffer for a single huge page plus 902 * extra space for the spare area and ECC storage area 903 */ 904 host->dma_buf_len = LPC32XX_DMA_DATA_SIZE + LPC32XX_ECC_SAVE_SIZE; 905 host->data_buf = devm_kzalloc(&pdev->dev, host->dma_buf_len, 906 GFP_KERNEL); 907 if (host->data_buf == NULL) { 908 res = -ENOMEM; 909 goto unprepare_clk; 910 } 911 912 res = lpc32xx_nand_dma_setup(host); 913 if (res) { 914 res = -EIO; 915 goto unprepare_clk; 916 } 917 918 /* Find NAND device */ 919 chip->legacy.dummy_controller.ops = &lpc32xx_nand_controller_ops; 920 res = nand_scan(chip, 1); 921 if (res) 922 goto release_dma; 923 924 mtd->name = "nxp_lpc3220_slc"; 925 res = mtd_device_register(mtd, host->ncfg->parts, 926 host->ncfg->num_parts); 927 if (res) 928 goto cleanup_nand; 929 930 return 0; 931 932 cleanup_nand: 933 nand_cleanup(chip); 934 release_dma: 935 dma_release_channel(host->dma_chan); 936 unprepare_clk: 937 clk_disable_unprepare(host->clk); 938 enable_wp: 939 lpc32xx_wp_enable(host); 940 941 return res; 942 } 943 944 /* 945 * Remove NAND device. 946 */ 947 static int lpc32xx_nand_remove(struct platform_device *pdev) 948 { 949 uint32_t tmp; 950 struct lpc32xx_nand_host *host = platform_get_drvdata(pdev); 951 struct nand_chip *chip = &host->nand_chip; 952 int ret; 953 954 ret = mtd_device_unregister(nand_to_mtd(chip)); 955 WARN_ON(ret); 956 nand_cleanup(chip); 957 dma_release_channel(host->dma_chan); 958 959 /* Force CE high */ 960 tmp = readl(SLC_CTRL(host->io_base)); 961 tmp &= ~SLCCFG_CE_LOW; 962 writel(tmp, SLC_CTRL(host->io_base)); 963 964 clk_disable_unprepare(host->clk); 965 lpc32xx_wp_enable(host); 966 967 return 0; 968 } 969 970 #ifdef CONFIG_PM 971 static int lpc32xx_nand_resume(struct platform_device *pdev) 972 { 973 struct lpc32xx_nand_host *host = platform_get_drvdata(pdev); 974 int ret; 975 976 /* Re-enable NAND clock */ 977 ret = clk_prepare_enable(host->clk); 978 if (ret) 979 return ret; 980 981 /* Fresh init of NAND controller */ 982 lpc32xx_nand_setup(host); 983 984 /* Disable write protect */ 985 lpc32xx_wp_disable(host); 986 987 return 0; 988 } 989 990 static int lpc32xx_nand_suspend(struct platform_device *pdev, pm_message_t pm) 991 { 992 uint32_t tmp; 993 struct lpc32xx_nand_host *host = platform_get_drvdata(pdev); 994 995 /* Force CE high */ 996 tmp = readl(SLC_CTRL(host->io_base)); 997 tmp &= ~SLCCFG_CE_LOW; 998 writel(tmp, SLC_CTRL(host->io_base)); 999 1000 /* Enable write protect for safety */ 1001 lpc32xx_wp_enable(host); 1002 1003 /* Disable clock */ 1004 clk_disable_unprepare(host->clk); 1005 1006 return 0; 1007 } 1008 1009 #else 1010 #define lpc32xx_nand_resume NULL 1011 #define lpc32xx_nand_suspend NULL 1012 #endif 1013 1014 static const struct of_device_id lpc32xx_nand_match[] = { 1015 { .compatible = "nxp,lpc3220-slc" }, 1016 { /* sentinel */ }, 1017 }; 1018 MODULE_DEVICE_TABLE(of, lpc32xx_nand_match); 1019 1020 static struct platform_driver lpc32xx_nand_driver = { 1021 .probe = lpc32xx_nand_probe, 1022 .remove = lpc32xx_nand_remove, 1023 .resume = lpc32xx_nand_resume, 1024 .suspend = lpc32xx_nand_suspend, 1025 .driver = { 1026 .name = LPC32XX_MODNAME, 1027 .of_match_table = lpc32xx_nand_match, 1028 }, 1029 }; 1030 1031 module_platform_driver(lpc32xx_nand_driver); 1032 1033 MODULE_LICENSE("GPL"); 1034 MODULE_AUTHOR("Kevin Wells <kevin.wells@nxp.com>"); 1035 MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>"); 1036 MODULE_DESCRIPTION("NAND driver for the NXP LPC32XX SLC controller"); 1037