1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Driver for NAND MLC Controller in LPC32xx 4 * 5 * Author: Roland Stigge <stigge@antcom.de> 6 * 7 * Copyright © 2011 WORK Microwave GmbH 8 * Copyright © 2011, 2012 Roland Stigge 9 * 10 * NAND Flash Controller Operation: 11 * - Read: Auto Decode 12 * - Write: Auto Encode 13 * - Tested Page Sizes: 2048, 4096 14 */ 15 16 #include <linux/slab.h> 17 #include <linux/module.h> 18 #include <linux/platform_device.h> 19 #include <linux/mtd/mtd.h> 20 #include <linux/mtd/rawnand.h> 21 #include <linux/mtd/partitions.h> 22 #include <linux/clk.h> 23 #include <linux/err.h> 24 #include <linux/delay.h> 25 #include <linux/completion.h> 26 #include <linux/interrupt.h> 27 #include <linux/of.h> 28 #include <linux/of_gpio.h> 29 #include <linux/mtd/lpc32xx_mlc.h> 30 #include <linux/io.h> 31 #include <linux/mm.h> 32 #include <linux/dma-mapping.h> 33 #include <linux/dmaengine.h> 34 #include <linux/mtd/nand_ecc.h> 35 36 #define DRV_NAME "lpc32xx_mlc" 37 38 /********************************************************************** 39 * MLC NAND controller register offsets 40 **********************************************************************/ 41 42 #define MLC_BUFF(x) (x + 0x00000) 43 #define MLC_DATA(x) (x + 0x08000) 44 #define MLC_CMD(x) (x + 0x10000) 45 #define MLC_ADDR(x) (x + 0x10004) 46 #define MLC_ECC_ENC_REG(x) (x + 0x10008) 47 #define MLC_ECC_DEC_REG(x) (x + 0x1000C) 48 #define MLC_ECC_AUTO_ENC_REG(x) (x + 0x10010) 49 #define MLC_ECC_AUTO_DEC_REG(x) (x + 0x10014) 50 #define MLC_RPR(x) (x + 0x10018) 51 #define MLC_WPR(x) (x + 0x1001C) 52 #define MLC_RUBP(x) (x + 0x10020) 53 #define MLC_ROBP(x) (x + 0x10024) 54 #define MLC_SW_WP_ADD_LOW(x) (x + 0x10028) 55 #define MLC_SW_WP_ADD_HIG(x) (x + 0x1002C) 56 #define MLC_ICR(x) (x + 0x10030) 57 #define MLC_TIME_REG(x) (x + 0x10034) 58 #define MLC_IRQ_MR(x) (x + 0x10038) 59 #define MLC_IRQ_SR(x) (x + 0x1003C) 60 #define MLC_LOCK_PR(x) (x + 0x10044) 61 #define MLC_ISR(x) (x + 0x10048) 62 #define MLC_CEH(x) (x + 0x1004C) 63 64 /********************************************************************** 65 * MLC_CMD bit definitions 66 **********************************************************************/ 67 #define MLCCMD_RESET 0xFF 68 69 /********************************************************************** 70 * MLC_ICR bit definitions 71 **********************************************************************/ 72 #define MLCICR_WPROT (1 << 3) 73 #define MLCICR_LARGEBLOCK (1 << 2) 74 #define MLCICR_LONGADDR (1 << 1) 75 #define MLCICR_16BIT (1 << 0) /* unsupported by LPC32x0! */ 76 77 /********************************************************************** 78 * MLC_TIME_REG bit definitions 79 **********************************************************************/ 80 #define MLCTIMEREG_TCEA_DELAY(n) (((n) & 0x03) << 24) 81 #define MLCTIMEREG_BUSY_DELAY(n) (((n) & 0x1F) << 19) 82 #define MLCTIMEREG_NAND_TA(n) (((n) & 0x07) << 16) 83 #define MLCTIMEREG_RD_HIGH(n) (((n) & 0x0F) << 12) 84 #define MLCTIMEREG_RD_LOW(n) (((n) & 0x0F) << 8) 85 #define MLCTIMEREG_WR_HIGH(n) (((n) & 0x0F) << 4) 86 #define MLCTIMEREG_WR_LOW(n) (((n) & 0x0F) << 0) 87 88 /********************************************************************** 89 * MLC_IRQ_MR and MLC_IRQ_SR bit definitions 90 **********************************************************************/ 91 #define MLCIRQ_NAND_READY (1 << 5) 92 #define MLCIRQ_CONTROLLER_READY (1 << 4) 93 #define MLCIRQ_DECODE_FAILURE (1 << 3) 94 #define MLCIRQ_DECODE_ERROR (1 << 2) 95 #define MLCIRQ_ECC_READY (1 << 1) 96 #define MLCIRQ_WRPROT_FAULT (1 << 0) 97 98 /********************************************************************** 99 * MLC_LOCK_PR bit definitions 100 **********************************************************************/ 101 #define MLCLOCKPR_MAGIC 0xA25E 102 103 /********************************************************************** 104 * MLC_ISR bit definitions 105 **********************************************************************/ 106 #define MLCISR_DECODER_FAILURE (1 << 6) 107 #define MLCISR_ERRORS ((1 << 4) | (1 << 5)) 108 #define MLCISR_ERRORS_DETECTED (1 << 3) 109 #define MLCISR_ECC_READY (1 << 2) 110 #define MLCISR_CONTROLLER_READY (1 << 1) 111 #define MLCISR_NAND_READY (1 << 0) 112 113 /********************************************************************** 114 * MLC_CEH bit definitions 115 **********************************************************************/ 116 #define MLCCEH_NORMAL (1 << 0) 117 118 struct lpc32xx_nand_cfg_mlc { 119 uint32_t tcea_delay; 120 uint32_t busy_delay; 121 uint32_t nand_ta; 122 uint32_t rd_high; 123 uint32_t rd_low; 124 uint32_t wr_high; 125 uint32_t wr_low; 126 int wp_gpio; 127 struct mtd_partition *parts; 128 unsigned num_parts; 129 }; 130 131 static int lpc32xx_ooblayout_ecc(struct mtd_info *mtd, int section, 132 struct mtd_oob_region *oobregion) 133 { 134 struct nand_chip *nand_chip = mtd_to_nand(mtd); 135 136 if (section >= nand_chip->ecc.steps) 137 return -ERANGE; 138 139 oobregion->offset = ((section + 1) * 16) - nand_chip->ecc.bytes; 140 oobregion->length = nand_chip->ecc.bytes; 141 142 return 0; 143 } 144 145 static int lpc32xx_ooblayout_free(struct mtd_info *mtd, int section, 146 struct mtd_oob_region *oobregion) 147 { 148 struct nand_chip *nand_chip = mtd_to_nand(mtd); 149 150 if (section >= nand_chip->ecc.steps) 151 return -ERANGE; 152 153 oobregion->offset = 16 * section; 154 oobregion->length = 16 - nand_chip->ecc.bytes; 155 156 return 0; 157 } 158 159 static const struct mtd_ooblayout_ops lpc32xx_ooblayout_ops = { 160 .ecc = lpc32xx_ooblayout_ecc, 161 .free = lpc32xx_ooblayout_free, 162 }; 163 164 static struct nand_bbt_descr lpc32xx_nand_bbt = { 165 .options = NAND_BBT_ABSPAGE | NAND_BBT_2BIT | NAND_BBT_NO_OOB | 166 NAND_BBT_WRITE, 167 .pages = { 524224, 0, 0, 0, 0, 0, 0, 0 }, 168 }; 169 170 static struct nand_bbt_descr lpc32xx_nand_bbt_mirror = { 171 .options = NAND_BBT_ABSPAGE | NAND_BBT_2BIT | NAND_BBT_NO_OOB | 172 NAND_BBT_WRITE, 173 .pages = { 524160, 0, 0, 0, 0, 0, 0, 0 }, 174 }; 175 176 struct lpc32xx_nand_host { 177 struct platform_device *pdev; 178 struct nand_chip nand_chip; 179 struct lpc32xx_mlc_platform_data *pdata; 180 struct clk *clk; 181 void __iomem *io_base; 182 int irq; 183 struct lpc32xx_nand_cfg_mlc *ncfg; 184 struct completion comp_nand; 185 struct completion comp_controller; 186 uint32_t llptr; 187 /* 188 * Physical addresses of ECC buffer, DMA data buffers, OOB data buffer 189 */ 190 dma_addr_t oob_buf_phy; 191 /* 192 * Virtual addresses of ECC buffer, DMA data buffers, OOB data buffer 193 */ 194 uint8_t *oob_buf; 195 /* Physical address of DMA base address */ 196 dma_addr_t io_base_phy; 197 198 struct completion comp_dma; 199 struct dma_chan *dma_chan; 200 struct dma_slave_config dma_slave_config; 201 struct scatterlist sgl; 202 uint8_t *dma_buf; 203 uint8_t *dummy_buf; 204 int mlcsubpages; /* number of 512bytes-subpages */ 205 }; 206 207 /* 208 * Activate/Deactivate DMA Operation: 209 * 210 * Using the PL080 DMA Controller for transferring the 512 byte subpages 211 * instead of doing readl() / writel() in a loop slows it down significantly. 212 * Measurements via getnstimeofday() upon 512 byte subpage reads reveal: 213 * 214 * - readl() of 128 x 32 bits in a loop: ~20us 215 * - DMA read of 512 bytes (32 bit, 4...128 words bursts): ~60us 216 * - DMA read of 512 bytes (32 bit, no bursts): ~100us 217 * 218 * This applies to the transfer itself. In the DMA case: only the 219 * wait_for_completion() (DMA setup _not_ included). 220 * 221 * Note that the 512 bytes subpage transfer is done directly from/to a 222 * FIFO/buffer inside the NAND controller. Most of the time (~400-800us for a 223 * 2048 bytes page) is spent waiting for the NAND IRQ, anyway. (The NAND 224 * controller transferring data between its internal buffer to/from the NAND 225 * chip.) 226 * 227 * Therefore, using the PL080 DMA is disabled by default, for now. 228 * 229 */ 230 static int use_dma; 231 232 static void lpc32xx_nand_setup(struct lpc32xx_nand_host *host) 233 { 234 uint32_t clkrate, tmp; 235 236 /* Reset MLC controller */ 237 writel(MLCCMD_RESET, MLC_CMD(host->io_base)); 238 udelay(1000); 239 240 /* Get base clock for MLC block */ 241 clkrate = clk_get_rate(host->clk); 242 if (clkrate == 0) 243 clkrate = 104000000; 244 245 /* Unlock MLC_ICR 246 * (among others, will be locked again automatically) */ 247 writew(MLCLOCKPR_MAGIC, MLC_LOCK_PR(host->io_base)); 248 249 /* Configure MLC Controller: Large Block, 5 Byte Address */ 250 tmp = MLCICR_LARGEBLOCK | MLCICR_LONGADDR; 251 writel(tmp, MLC_ICR(host->io_base)); 252 253 /* Unlock MLC_TIME_REG 254 * (among others, will be locked again automatically) */ 255 writew(MLCLOCKPR_MAGIC, MLC_LOCK_PR(host->io_base)); 256 257 /* Compute clock setup values, see LPC and NAND manual */ 258 tmp = 0; 259 tmp |= MLCTIMEREG_TCEA_DELAY(clkrate / host->ncfg->tcea_delay + 1); 260 tmp |= MLCTIMEREG_BUSY_DELAY(clkrate / host->ncfg->busy_delay + 1); 261 tmp |= MLCTIMEREG_NAND_TA(clkrate / host->ncfg->nand_ta + 1); 262 tmp |= MLCTIMEREG_RD_HIGH(clkrate / host->ncfg->rd_high + 1); 263 tmp |= MLCTIMEREG_RD_LOW(clkrate / host->ncfg->rd_low); 264 tmp |= MLCTIMEREG_WR_HIGH(clkrate / host->ncfg->wr_high + 1); 265 tmp |= MLCTIMEREG_WR_LOW(clkrate / host->ncfg->wr_low); 266 writel(tmp, MLC_TIME_REG(host->io_base)); 267 268 /* Enable IRQ for CONTROLLER_READY and NAND_READY */ 269 writeb(MLCIRQ_CONTROLLER_READY | MLCIRQ_NAND_READY, 270 MLC_IRQ_MR(host->io_base)); 271 272 /* Normal nCE operation: nCE controlled by controller */ 273 writel(MLCCEH_NORMAL, MLC_CEH(host->io_base)); 274 } 275 276 /* 277 * Hardware specific access to control lines 278 */ 279 static void lpc32xx_nand_cmd_ctrl(struct nand_chip *nand_chip, int cmd, 280 unsigned int ctrl) 281 { 282 struct lpc32xx_nand_host *host = nand_get_controller_data(nand_chip); 283 284 if (cmd != NAND_CMD_NONE) { 285 if (ctrl & NAND_CLE) 286 writel(cmd, MLC_CMD(host->io_base)); 287 else 288 writel(cmd, MLC_ADDR(host->io_base)); 289 } 290 } 291 292 /* 293 * Read Device Ready (NAND device _and_ controller ready) 294 */ 295 static int lpc32xx_nand_device_ready(struct nand_chip *nand_chip) 296 { 297 struct lpc32xx_nand_host *host = nand_get_controller_data(nand_chip); 298 299 if ((readb(MLC_ISR(host->io_base)) & 300 (MLCISR_CONTROLLER_READY | MLCISR_NAND_READY)) == 301 (MLCISR_CONTROLLER_READY | MLCISR_NAND_READY)) 302 return 1; 303 304 return 0; 305 } 306 307 static irqreturn_t lpc3xxx_nand_irq(int irq, struct lpc32xx_nand_host *host) 308 { 309 uint8_t sr; 310 311 /* Clear interrupt flag by reading status */ 312 sr = readb(MLC_IRQ_SR(host->io_base)); 313 if (sr & MLCIRQ_NAND_READY) 314 complete(&host->comp_nand); 315 if (sr & MLCIRQ_CONTROLLER_READY) 316 complete(&host->comp_controller); 317 318 return IRQ_HANDLED; 319 } 320 321 static int lpc32xx_waitfunc_nand(struct nand_chip *chip) 322 { 323 struct mtd_info *mtd = nand_to_mtd(chip); 324 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 325 326 if (readb(MLC_ISR(host->io_base)) & MLCISR_NAND_READY) 327 goto exit; 328 329 wait_for_completion(&host->comp_nand); 330 331 while (!(readb(MLC_ISR(host->io_base)) & MLCISR_NAND_READY)) { 332 /* Seems to be delayed sometimes by controller */ 333 dev_dbg(&mtd->dev, "Warning: NAND not ready.\n"); 334 cpu_relax(); 335 } 336 337 exit: 338 return NAND_STATUS_READY; 339 } 340 341 static int lpc32xx_waitfunc_controller(struct nand_chip *chip) 342 { 343 struct mtd_info *mtd = nand_to_mtd(chip); 344 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 345 346 if (readb(MLC_ISR(host->io_base)) & MLCISR_CONTROLLER_READY) 347 goto exit; 348 349 wait_for_completion(&host->comp_controller); 350 351 while (!(readb(MLC_ISR(host->io_base)) & 352 MLCISR_CONTROLLER_READY)) { 353 dev_dbg(&mtd->dev, "Warning: Controller not ready.\n"); 354 cpu_relax(); 355 } 356 357 exit: 358 return NAND_STATUS_READY; 359 } 360 361 static int lpc32xx_waitfunc(struct nand_chip *chip) 362 { 363 lpc32xx_waitfunc_nand(chip); 364 lpc32xx_waitfunc_controller(chip); 365 366 return NAND_STATUS_READY; 367 } 368 369 /* 370 * Enable NAND write protect 371 */ 372 static void lpc32xx_wp_enable(struct lpc32xx_nand_host *host) 373 { 374 if (gpio_is_valid(host->ncfg->wp_gpio)) 375 gpio_set_value(host->ncfg->wp_gpio, 0); 376 } 377 378 /* 379 * Disable NAND write protect 380 */ 381 static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host) 382 { 383 if (gpio_is_valid(host->ncfg->wp_gpio)) 384 gpio_set_value(host->ncfg->wp_gpio, 1); 385 } 386 387 static void lpc32xx_dma_complete_func(void *completion) 388 { 389 complete(completion); 390 } 391 392 static int lpc32xx_xmit_dma(struct mtd_info *mtd, void *mem, int len, 393 enum dma_transfer_direction dir) 394 { 395 struct nand_chip *chip = mtd_to_nand(mtd); 396 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 397 struct dma_async_tx_descriptor *desc; 398 int flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT; 399 int res; 400 401 sg_init_one(&host->sgl, mem, len); 402 403 res = dma_map_sg(host->dma_chan->device->dev, &host->sgl, 1, 404 DMA_BIDIRECTIONAL); 405 if (res != 1) { 406 dev_err(mtd->dev.parent, "Failed to map sg list\n"); 407 return -ENXIO; 408 } 409 desc = dmaengine_prep_slave_sg(host->dma_chan, &host->sgl, 1, dir, 410 flags); 411 if (!desc) { 412 dev_err(mtd->dev.parent, "Failed to prepare slave sg\n"); 413 goto out1; 414 } 415 416 init_completion(&host->comp_dma); 417 desc->callback = lpc32xx_dma_complete_func; 418 desc->callback_param = &host->comp_dma; 419 420 dmaengine_submit(desc); 421 dma_async_issue_pending(host->dma_chan); 422 423 wait_for_completion_timeout(&host->comp_dma, msecs_to_jiffies(1000)); 424 425 dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1, 426 DMA_BIDIRECTIONAL); 427 return 0; 428 out1: 429 dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1, 430 DMA_BIDIRECTIONAL); 431 return -ENXIO; 432 } 433 434 static int lpc32xx_read_page(struct nand_chip *chip, uint8_t *buf, 435 int oob_required, int page) 436 { 437 struct mtd_info *mtd = nand_to_mtd(chip); 438 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 439 int i, j; 440 uint8_t *oobbuf = chip->oob_poi; 441 uint32_t mlc_isr; 442 int res; 443 uint8_t *dma_buf; 444 bool dma_mapped; 445 446 if ((void *)buf <= high_memory) { 447 dma_buf = buf; 448 dma_mapped = true; 449 } else { 450 dma_buf = host->dma_buf; 451 dma_mapped = false; 452 } 453 454 /* Writing Command and Address */ 455 nand_read_page_op(chip, page, 0, NULL, 0); 456 457 /* For all sub-pages */ 458 for (i = 0; i < host->mlcsubpages; i++) { 459 /* Start Auto Decode Command */ 460 writeb(0x00, MLC_ECC_AUTO_DEC_REG(host->io_base)); 461 462 /* Wait for Controller Ready */ 463 lpc32xx_waitfunc_controller(chip); 464 465 /* Check ECC Error status */ 466 mlc_isr = readl(MLC_ISR(host->io_base)); 467 if (mlc_isr & MLCISR_DECODER_FAILURE) { 468 mtd->ecc_stats.failed++; 469 dev_warn(&mtd->dev, "%s: DECODER_FAILURE\n", __func__); 470 } else if (mlc_isr & MLCISR_ERRORS_DETECTED) { 471 mtd->ecc_stats.corrected += ((mlc_isr >> 4) & 0x3) + 1; 472 } 473 474 /* Read 512 + 16 Bytes */ 475 if (use_dma) { 476 res = lpc32xx_xmit_dma(mtd, dma_buf + i * 512, 512, 477 DMA_DEV_TO_MEM); 478 if (res) 479 return res; 480 } else { 481 for (j = 0; j < (512 >> 2); j++) { 482 *((uint32_t *)(buf)) = 483 readl(MLC_BUFF(host->io_base)); 484 buf += 4; 485 } 486 } 487 for (j = 0; j < (16 >> 2); j++) { 488 *((uint32_t *)(oobbuf)) = 489 readl(MLC_BUFF(host->io_base)); 490 oobbuf += 4; 491 } 492 } 493 494 if (use_dma && !dma_mapped) 495 memcpy(buf, dma_buf, mtd->writesize); 496 497 return 0; 498 } 499 500 static int lpc32xx_write_page_lowlevel(struct nand_chip *chip, 501 const uint8_t *buf, int oob_required, 502 int page) 503 { 504 struct mtd_info *mtd = nand_to_mtd(chip); 505 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 506 const uint8_t *oobbuf = chip->oob_poi; 507 uint8_t *dma_buf = (uint8_t *)buf; 508 int res; 509 int i, j; 510 511 if (use_dma && (void *)buf >= high_memory) { 512 dma_buf = host->dma_buf; 513 memcpy(dma_buf, buf, mtd->writesize); 514 } 515 516 nand_prog_page_begin_op(chip, page, 0, NULL, 0); 517 518 for (i = 0; i < host->mlcsubpages; i++) { 519 /* Start Encode */ 520 writeb(0x00, MLC_ECC_ENC_REG(host->io_base)); 521 522 /* Write 512 + 6 Bytes to Buffer */ 523 if (use_dma) { 524 res = lpc32xx_xmit_dma(mtd, dma_buf + i * 512, 512, 525 DMA_MEM_TO_DEV); 526 if (res) 527 return res; 528 } else { 529 for (j = 0; j < (512 >> 2); j++) { 530 writel(*((uint32_t *)(buf)), 531 MLC_BUFF(host->io_base)); 532 buf += 4; 533 } 534 } 535 writel(*((uint32_t *)(oobbuf)), MLC_BUFF(host->io_base)); 536 oobbuf += 4; 537 writew(*((uint16_t *)(oobbuf)), MLC_BUFF(host->io_base)); 538 oobbuf += 12; 539 540 /* Auto Encode w/ Bit 8 = 0 (see LPC MLC Controller manual) */ 541 writeb(0x00, MLC_ECC_AUTO_ENC_REG(host->io_base)); 542 543 /* Wait for Controller Ready */ 544 lpc32xx_waitfunc_controller(chip); 545 } 546 547 return nand_prog_page_end_op(chip); 548 } 549 550 static int lpc32xx_read_oob(struct nand_chip *chip, int page) 551 { 552 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 553 554 /* Read whole page - necessary with MLC controller! */ 555 lpc32xx_read_page(chip, host->dummy_buf, 1, page); 556 557 return 0; 558 } 559 560 static int lpc32xx_write_oob(struct nand_chip *chip, int page) 561 { 562 /* None, write_oob conflicts with the automatic LPC MLC ECC decoder! */ 563 return 0; 564 } 565 566 /* Prepares MLC for transfers with H/W ECC enabled: always enabled anyway */ 567 static void lpc32xx_ecc_enable(struct nand_chip *chip, int mode) 568 { 569 /* Always enabled! */ 570 } 571 572 static int lpc32xx_dma_setup(struct lpc32xx_nand_host *host) 573 { 574 struct mtd_info *mtd = nand_to_mtd(&host->nand_chip); 575 dma_cap_mask_t mask; 576 577 if (!host->pdata || !host->pdata->dma_filter) { 578 dev_err(mtd->dev.parent, "no DMA platform data\n"); 579 return -ENOENT; 580 } 581 582 dma_cap_zero(mask); 583 dma_cap_set(DMA_SLAVE, mask); 584 host->dma_chan = dma_request_channel(mask, host->pdata->dma_filter, 585 "nand-mlc"); 586 if (!host->dma_chan) { 587 dev_err(mtd->dev.parent, "Failed to request DMA channel\n"); 588 return -EBUSY; 589 } 590 591 /* 592 * Set direction to a sensible value even if the dmaengine driver 593 * should ignore it. With the default (DMA_MEM_TO_MEM), the amba-pl08x 594 * driver criticizes it as "alien transfer direction". 595 */ 596 host->dma_slave_config.direction = DMA_DEV_TO_MEM; 597 host->dma_slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; 598 host->dma_slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; 599 host->dma_slave_config.src_maxburst = 128; 600 host->dma_slave_config.dst_maxburst = 128; 601 /* DMA controller does flow control: */ 602 host->dma_slave_config.device_fc = false; 603 host->dma_slave_config.src_addr = MLC_BUFF(host->io_base_phy); 604 host->dma_slave_config.dst_addr = MLC_BUFF(host->io_base_phy); 605 if (dmaengine_slave_config(host->dma_chan, &host->dma_slave_config)) { 606 dev_err(mtd->dev.parent, "Failed to setup DMA slave\n"); 607 goto out1; 608 } 609 610 return 0; 611 out1: 612 dma_release_channel(host->dma_chan); 613 return -ENXIO; 614 } 615 616 static struct lpc32xx_nand_cfg_mlc *lpc32xx_parse_dt(struct device *dev) 617 { 618 struct lpc32xx_nand_cfg_mlc *ncfg; 619 struct device_node *np = dev->of_node; 620 621 ncfg = devm_kzalloc(dev, sizeof(*ncfg), GFP_KERNEL); 622 if (!ncfg) 623 return NULL; 624 625 of_property_read_u32(np, "nxp,tcea-delay", &ncfg->tcea_delay); 626 of_property_read_u32(np, "nxp,busy-delay", &ncfg->busy_delay); 627 of_property_read_u32(np, "nxp,nand-ta", &ncfg->nand_ta); 628 of_property_read_u32(np, "nxp,rd-high", &ncfg->rd_high); 629 of_property_read_u32(np, "nxp,rd-low", &ncfg->rd_low); 630 of_property_read_u32(np, "nxp,wr-high", &ncfg->wr_high); 631 of_property_read_u32(np, "nxp,wr-low", &ncfg->wr_low); 632 633 if (!ncfg->tcea_delay || !ncfg->busy_delay || !ncfg->nand_ta || 634 !ncfg->rd_high || !ncfg->rd_low || !ncfg->wr_high || 635 !ncfg->wr_low) { 636 dev_err(dev, "chip parameters not specified correctly\n"); 637 return NULL; 638 } 639 640 ncfg->wp_gpio = of_get_named_gpio(np, "gpios", 0); 641 642 return ncfg; 643 } 644 645 static int lpc32xx_nand_attach_chip(struct nand_chip *chip) 646 { 647 struct mtd_info *mtd = nand_to_mtd(chip); 648 struct lpc32xx_nand_host *host = nand_get_controller_data(chip); 649 struct device *dev = &host->pdev->dev; 650 651 host->dma_buf = devm_kzalloc(dev, mtd->writesize, GFP_KERNEL); 652 if (!host->dma_buf) 653 return -ENOMEM; 654 655 host->dummy_buf = devm_kzalloc(dev, mtd->writesize, GFP_KERNEL); 656 if (!host->dummy_buf) 657 return -ENOMEM; 658 659 chip->ecc.mode = NAND_ECC_HW; 660 chip->ecc.size = 512; 661 mtd_set_ooblayout(mtd, &lpc32xx_ooblayout_ops); 662 host->mlcsubpages = mtd->writesize / 512; 663 664 return 0; 665 } 666 667 static const struct nand_controller_ops lpc32xx_nand_controller_ops = { 668 .attach_chip = lpc32xx_nand_attach_chip, 669 }; 670 671 /* 672 * Probe for NAND controller 673 */ 674 static int lpc32xx_nand_probe(struct platform_device *pdev) 675 { 676 struct lpc32xx_nand_host *host; 677 struct mtd_info *mtd; 678 struct nand_chip *nand_chip; 679 struct resource *rc; 680 int res; 681 682 /* Allocate memory for the device structure (and zero it) */ 683 host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL); 684 if (!host) 685 return -ENOMEM; 686 687 host->pdev = pdev; 688 689 rc = platform_get_resource(pdev, IORESOURCE_MEM, 0); 690 host->io_base = devm_ioremap_resource(&pdev->dev, rc); 691 if (IS_ERR(host->io_base)) 692 return PTR_ERR(host->io_base); 693 694 host->io_base_phy = rc->start; 695 696 nand_chip = &host->nand_chip; 697 mtd = nand_to_mtd(nand_chip); 698 if (pdev->dev.of_node) 699 host->ncfg = lpc32xx_parse_dt(&pdev->dev); 700 if (!host->ncfg) { 701 dev_err(&pdev->dev, 702 "Missing or bad NAND config from device tree\n"); 703 return -ENOENT; 704 } 705 if (host->ncfg->wp_gpio == -EPROBE_DEFER) 706 return -EPROBE_DEFER; 707 if (gpio_is_valid(host->ncfg->wp_gpio) && 708 gpio_request(host->ncfg->wp_gpio, "NAND WP")) { 709 dev_err(&pdev->dev, "GPIO not available\n"); 710 return -EBUSY; 711 } 712 lpc32xx_wp_disable(host); 713 714 host->pdata = dev_get_platdata(&pdev->dev); 715 716 /* link the private data structures */ 717 nand_set_controller_data(nand_chip, host); 718 nand_set_flash_node(nand_chip, pdev->dev.of_node); 719 mtd->dev.parent = &pdev->dev; 720 721 /* Get NAND clock */ 722 host->clk = clk_get(&pdev->dev, NULL); 723 if (IS_ERR(host->clk)) { 724 dev_err(&pdev->dev, "Clock initialization failure\n"); 725 res = -ENOENT; 726 goto free_gpio; 727 } 728 res = clk_prepare_enable(host->clk); 729 if (res) 730 goto put_clk; 731 732 nand_chip->legacy.cmd_ctrl = lpc32xx_nand_cmd_ctrl; 733 nand_chip->legacy.dev_ready = lpc32xx_nand_device_ready; 734 nand_chip->legacy.chip_delay = 25; /* us */ 735 nand_chip->legacy.IO_ADDR_R = MLC_DATA(host->io_base); 736 nand_chip->legacy.IO_ADDR_W = MLC_DATA(host->io_base); 737 738 /* Init NAND controller */ 739 lpc32xx_nand_setup(host); 740 741 platform_set_drvdata(pdev, host); 742 743 /* Initialize function pointers */ 744 nand_chip->ecc.hwctl = lpc32xx_ecc_enable; 745 nand_chip->ecc.read_page_raw = lpc32xx_read_page; 746 nand_chip->ecc.read_page = lpc32xx_read_page; 747 nand_chip->ecc.write_page_raw = lpc32xx_write_page_lowlevel; 748 nand_chip->ecc.write_page = lpc32xx_write_page_lowlevel; 749 nand_chip->ecc.write_oob = lpc32xx_write_oob; 750 nand_chip->ecc.read_oob = lpc32xx_read_oob; 751 nand_chip->ecc.strength = 4; 752 nand_chip->ecc.bytes = 10; 753 nand_chip->legacy.waitfunc = lpc32xx_waitfunc; 754 755 nand_chip->options = NAND_NO_SUBPAGE_WRITE; 756 nand_chip->bbt_options = NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB; 757 nand_chip->bbt_td = &lpc32xx_nand_bbt; 758 nand_chip->bbt_md = &lpc32xx_nand_bbt_mirror; 759 760 if (use_dma) { 761 res = lpc32xx_dma_setup(host); 762 if (res) { 763 res = -EIO; 764 goto unprepare_clk; 765 } 766 } 767 768 /* initially clear interrupt status */ 769 readb(MLC_IRQ_SR(host->io_base)); 770 771 init_completion(&host->comp_nand); 772 init_completion(&host->comp_controller); 773 774 host->irq = platform_get_irq(pdev, 0); 775 if (host->irq < 0) { 776 res = -EINVAL; 777 goto release_dma_chan; 778 } 779 780 if (request_irq(host->irq, (irq_handler_t)&lpc3xxx_nand_irq, 781 IRQF_TRIGGER_HIGH, DRV_NAME, host)) { 782 dev_err(&pdev->dev, "Error requesting NAND IRQ\n"); 783 res = -ENXIO; 784 goto release_dma_chan; 785 } 786 787 /* 788 * Scan to find existence of the device and get the type of NAND device: 789 * SMALL block or LARGE block. 790 */ 791 nand_chip->legacy.dummy_controller.ops = &lpc32xx_nand_controller_ops; 792 res = nand_scan(nand_chip, 1); 793 if (res) 794 goto free_irq; 795 796 mtd->name = DRV_NAME; 797 798 res = mtd_device_register(mtd, host->ncfg->parts, 799 host->ncfg->num_parts); 800 if (res) 801 goto cleanup_nand; 802 803 return 0; 804 805 cleanup_nand: 806 nand_cleanup(nand_chip); 807 free_irq: 808 free_irq(host->irq, host); 809 release_dma_chan: 810 if (use_dma) 811 dma_release_channel(host->dma_chan); 812 unprepare_clk: 813 clk_disable_unprepare(host->clk); 814 put_clk: 815 clk_put(host->clk); 816 free_gpio: 817 lpc32xx_wp_enable(host); 818 gpio_free(host->ncfg->wp_gpio); 819 820 return res; 821 } 822 823 /* 824 * Remove NAND device 825 */ 826 static int lpc32xx_nand_remove(struct platform_device *pdev) 827 { 828 struct lpc32xx_nand_host *host = platform_get_drvdata(pdev); 829 830 nand_release(&host->nand_chip); 831 free_irq(host->irq, host); 832 if (use_dma) 833 dma_release_channel(host->dma_chan); 834 835 clk_disable_unprepare(host->clk); 836 clk_put(host->clk); 837 838 lpc32xx_wp_enable(host); 839 gpio_free(host->ncfg->wp_gpio); 840 841 return 0; 842 } 843 844 #ifdef CONFIG_PM 845 static int lpc32xx_nand_resume(struct platform_device *pdev) 846 { 847 struct lpc32xx_nand_host *host = platform_get_drvdata(pdev); 848 int ret; 849 850 /* Re-enable NAND clock */ 851 ret = clk_prepare_enable(host->clk); 852 if (ret) 853 return ret; 854 855 /* Fresh init of NAND controller */ 856 lpc32xx_nand_setup(host); 857 858 /* Disable write protect */ 859 lpc32xx_wp_disable(host); 860 861 return 0; 862 } 863 864 static int lpc32xx_nand_suspend(struct platform_device *pdev, pm_message_t pm) 865 { 866 struct lpc32xx_nand_host *host = platform_get_drvdata(pdev); 867 868 /* Enable write protect for safety */ 869 lpc32xx_wp_enable(host); 870 871 /* Disable clock */ 872 clk_disable_unprepare(host->clk); 873 return 0; 874 } 875 876 #else 877 #define lpc32xx_nand_resume NULL 878 #define lpc32xx_nand_suspend NULL 879 #endif 880 881 static const struct of_device_id lpc32xx_nand_match[] = { 882 { .compatible = "nxp,lpc3220-mlc" }, 883 { /* sentinel */ }, 884 }; 885 MODULE_DEVICE_TABLE(of, lpc32xx_nand_match); 886 887 static struct platform_driver lpc32xx_nand_driver = { 888 .probe = lpc32xx_nand_probe, 889 .remove = lpc32xx_nand_remove, 890 .resume = lpc32xx_nand_resume, 891 .suspend = lpc32xx_nand_suspend, 892 .driver = { 893 .name = DRV_NAME, 894 .of_match_table = lpc32xx_nand_match, 895 }, 896 }; 897 898 module_platform_driver(lpc32xx_nand_driver); 899 900 MODULE_LICENSE("GPL"); 901 MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>"); 902 MODULE_DESCRIPTION("NAND driver for the NXP LPC32XX MLC controller"); 903