1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * Arasan NAND Flash Controller Driver
4  *
5  * Copyright (C) 2014 - 2020 Xilinx, Inc.
6  * Author:
7  *   Miquel Raynal <miquel.raynal@bootlin.com>
8  * Original work (fully rewritten):
9  *   Punnaiah Choudary Kalluri <punnaia@xilinx.com>
10  *   Naga Sureshkumar Relli <nagasure@xilinx.com>
11  */
12 
13 #include <linux/bch.h>
14 #include <linux/bitfield.h>
15 #include <linux/clk.h>
16 #include <linux/delay.h>
17 #include <linux/dma-mapping.h>
18 #include <linux/gpio/consumer.h>
19 #include <linux/interrupt.h>
20 #include <linux/iopoll.h>
21 #include <linux/module.h>
22 #include <linux/mtd/mtd.h>
23 #include <linux/mtd/partitions.h>
24 #include <linux/mtd/rawnand.h>
25 #include <linux/of.h>
26 #include <linux/platform_device.h>
27 #include <linux/slab.h>
28 
29 #define PKT_REG				0x00
30 #define   PKT_SIZE(x)			FIELD_PREP(GENMASK(10, 0), (x))
31 #define   PKT_STEPS(x)			FIELD_PREP(GENMASK(23, 12), (x))
32 
33 #define MEM_ADDR1_REG			0x04
34 
35 #define MEM_ADDR2_REG			0x08
36 #define   ADDR2_STRENGTH(x)		FIELD_PREP(GENMASK(27, 25), (x))
37 #define   ADDR2_CS(x)			FIELD_PREP(GENMASK(31, 30), (x))
38 
39 #define CMD_REG				0x0C
40 #define   CMD_1(x)			FIELD_PREP(GENMASK(7, 0), (x))
41 #define   CMD_2(x)			FIELD_PREP(GENMASK(15, 8), (x))
42 #define   CMD_PAGE_SIZE(x)		FIELD_PREP(GENMASK(25, 23), (x))
43 #define   CMD_DMA_ENABLE		BIT(27)
44 #define   CMD_NADDRS(x)			FIELD_PREP(GENMASK(30, 28), (x))
45 #define   CMD_ECC_ENABLE		BIT(31)
46 
47 #define PROG_REG			0x10
48 #define   PROG_PGRD			BIT(0)
49 #define   PROG_ERASE			BIT(2)
50 #define   PROG_STATUS			BIT(3)
51 #define   PROG_PGPROG			BIT(4)
52 #define   PROG_RDID			BIT(6)
53 #define   PROG_RDPARAM			BIT(7)
54 #define   PROG_RST			BIT(8)
55 #define   PROG_GET_FEATURE		BIT(9)
56 #define   PROG_SET_FEATURE		BIT(10)
57 #define   PROG_CHG_RD_COL_ENH		BIT(14)
58 
59 #define INTR_STS_EN_REG			0x14
60 #define INTR_SIG_EN_REG			0x18
61 #define INTR_STS_REG			0x1C
62 #define   WRITE_READY			BIT(0)
63 #define   READ_READY			BIT(1)
64 #define   XFER_COMPLETE			BIT(2)
65 #define   DMA_BOUNDARY			BIT(6)
66 #define   EVENT_MASK			GENMASK(7, 0)
67 
68 #define READY_STS_REG			0x20
69 
70 #define DMA_ADDR0_REG			0x50
71 #define DMA_ADDR1_REG			0x24
72 
73 #define FLASH_STS_REG			0x28
74 
75 #define TIMING_REG			0x2C
76 #define   TCCS_TIME_500NS		0
77 #define   TCCS_TIME_300NS		3
78 #define   TCCS_TIME_200NS		2
79 #define   TCCS_TIME_100NS		1
80 #define   FAST_TCAD			BIT(2)
81 #define   DQS_BUFF_SEL_IN(x)		FIELD_PREP(GENMASK(6, 3), (x))
82 #define   DQS_BUFF_SEL_OUT(x)		FIELD_PREP(GENMASK(18, 15), (x))
83 
84 #define DATA_PORT_REG			0x30
85 
86 #define ECC_CONF_REG			0x34
87 #define   ECC_CONF_COL(x)		FIELD_PREP(GENMASK(15, 0), (x))
88 #define   ECC_CONF_LEN(x)		FIELD_PREP(GENMASK(26, 16), (x))
89 #define   ECC_CONF_BCH_EN		BIT(27)
90 
91 #define ECC_ERR_CNT_REG			0x38
92 #define   GET_PKT_ERR_CNT(x)		FIELD_GET(GENMASK(7, 0), (x))
93 #define   GET_PAGE_ERR_CNT(x)		FIELD_GET(GENMASK(16, 8), (x))
94 
95 #define ECC_SP_REG			0x3C
96 #define   ECC_SP_CMD1(x)		FIELD_PREP(GENMASK(7, 0), (x))
97 #define   ECC_SP_CMD2(x)		FIELD_PREP(GENMASK(15, 8), (x))
98 #define   ECC_SP_ADDRS(x)		FIELD_PREP(GENMASK(30, 28), (x))
99 
100 #define ECC_1ERR_CNT_REG		0x40
101 #define ECC_2ERR_CNT_REG		0x44
102 
103 #define DATA_INTERFACE_REG		0x6C
104 #define   DIFACE_SDR_MODE(x)		FIELD_PREP(GENMASK(2, 0), (x))
105 #define   DIFACE_DDR_MODE(x)		FIELD_PREP(GENMASK(5, 3), (x))
106 #define   DIFACE_SDR			0
107 #define   DIFACE_NVDDR			BIT(9)
108 
109 #define ANFC_MAX_CS			2
110 #define ANFC_DFLT_TIMEOUT_US		1000000
111 #define ANFC_MAX_CHUNK_SIZE		SZ_1M
112 #define ANFC_MAX_PARAM_SIZE		SZ_4K
113 #define ANFC_MAX_STEPS			SZ_2K
114 #define ANFC_MAX_PKT_SIZE		(SZ_2K - 1)
115 #define ANFC_MAX_ADDR_CYC		5U
116 #define ANFC_RSVD_ECC_BYTES		21
117 
118 #define ANFC_XLNX_SDR_DFLT_CORE_CLK	100000000
119 #define ANFC_XLNX_SDR_HS_CORE_CLK	80000000
120 
121 static struct gpio_desc *anfc_default_cs_array[2] = {NULL, NULL};
122 
123 /**
124  * struct anfc_op - Defines how to execute an operation
125  * @pkt_reg: Packet register
126  * @addr1_reg: Memory address 1 register
127  * @addr2_reg: Memory address 2 register
128  * @cmd_reg: Command register
129  * @prog_reg: Program register
130  * @steps: Number of "packets" to read/write
131  * @rdy_timeout_ms: Timeout for waits on Ready/Busy pin
132  * @len: Data transfer length
133  * @read: Data transfer direction from the controller point of view
134  * @buf: Data buffer
135  */
136 struct anfc_op {
137 	u32 pkt_reg;
138 	u32 addr1_reg;
139 	u32 addr2_reg;
140 	u32 cmd_reg;
141 	u32 prog_reg;
142 	int steps;
143 	unsigned int rdy_timeout_ms;
144 	unsigned int len;
145 	bool read;
146 	u8 *buf;
147 };
148 
149 /**
150  * struct anand - Defines the NAND chip related information
151  * @node:		Used to store NAND chips into a list
152  * @chip:		NAND chip information structure
153  * @rb:			Ready-busy line
154  * @page_sz:		Register value of the page_sz field to use
155  * @clk:		Expected clock frequency to use
156  * @data_iface:		Data interface timing mode to use
157  * @timings:		NV-DDR specific timings to use
158  * @ecc_conf:		Hardware ECC configuration value
159  * @strength:		Register value of the ECC strength
160  * @raddr_cycles:	Row address cycle information
161  * @caddr_cycles:	Column address cycle information
162  * @ecc_bits:		Exact number of ECC bits per syndrome
163  * @ecc_total:		Total number of ECC bytes
164  * @errloc:		Array of errors located with soft BCH
165  * @hw_ecc:		Buffer to store syndromes computed by hardware
166  * @bch:		BCH structure
167  * @cs_idx:		Array of chip-select for this device, values are indexes
168  *			of the controller structure @gpio_cs array
169  * @ncs_idx:		Size of the @cs_idx array
170  */
171 struct anand {
172 	struct list_head node;
173 	struct nand_chip chip;
174 	unsigned int rb;
175 	unsigned int page_sz;
176 	unsigned long clk;
177 	u32 data_iface;
178 	u32 timings;
179 	u32 ecc_conf;
180 	u32 strength;
181 	u16 raddr_cycles;
182 	u16 caddr_cycles;
183 	unsigned int ecc_bits;
184 	unsigned int ecc_total;
185 	unsigned int *errloc;
186 	u8 *hw_ecc;
187 	struct bch_control *bch;
188 	int *cs_idx;
189 	int ncs_idx;
190 };
191 
192 /**
193  * struct arasan_nfc - Defines the Arasan NAND flash controller driver instance
194  * @dev:		Pointer to the device structure
195  * @base:		Remapped register area
196  * @controller_clk:		Pointer to the system clock
197  * @bus_clk:		Pointer to the flash clock
198  * @controller:		Base controller structure
199  * @chips:		List of all NAND chips attached to the controller
200  * @cur_clk:		Current clock rate
201  * @cs_array:		CS array. Native CS are left empty, the other cells are
202  *			populated with their corresponding GPIO descriptor.
203  * @ncs:		Size of @cs_array
204  * @cur_cs:		Index in @cs_array of the currently in use CS
205  * @native_cs:		Currently selected native CS
206  * @spare_cs:		Native CS that is not wired (may be selected when a GPIO
207  *			CS is in use)
208  */
209 struct arasan_nfc {
210 	struct device *dev;
211 	void __iomem *base;
212 	struct clk *controller_clk;
213 	struct clk *bus_clk;
214 	struct nand_controller controller;
215 	struct list_head chips;
216 	unsigned int cur_clk;
217 	struct gpio_desc **cs_array;
218 	unsigned int ncs;
219 	int cur_cs;
220 	unsigned int native_cs;
221 	unsigned int spare_cs;
222 };
223 
224 static struct anand *to_anand(struct nand_chip *nand)
225 {
226 	return container_of(nand, struct anand, chip);
227 }
228 
229 static struct arasan_nfc *to_anfc(struct nand_controller *ctrl)
230 {
231 	return container_of(ctrl, struct arasan_nfc, controller);
232 }
233 
234 static int anfc_wait_for_event(struct arasan_nfc *nfc, unsigned int event)
235 {
236 	u32 val;
237 	int ret;
238 
239 	ret = readl_relaxed_poll_timeout(nfc->base + INTR_STS_REG, val,
240 					 val & event, 0,
241 					 ANFC_DFLT_TIMEOUT_US);
242 	if (ret) {
243 		dev_err(nfc->dev, "Timeout waiting for event 0x%x\n", event);
244 		return -ETIMEDOUT;
245 	}
246 
247 	writel_relaxed(event, nfc->base + INTR_STS_REG);
248 
249 	return 0;
250 }
251 
252 static int anfc_wait_for_rb(struct arasan_nfc *nfc, struct nand_chip *chip,
253 			    unsigned int timeout_ms)
254 {
255 	struct anand *anand = to_anand(chip);
256 	u32 val;
257 	int ret;
258 
259 	/* There is no R/B interrupt, we must poll a register */
260 	ret = readl_relaxed_poll_timeout(nfc->base + READY_STS_REG, val,
261 					 val & BIT(anand->rb),
262 					 1, timeout_ms * 1000);
263 	if (ret) {
264 		dev_err(nfc->dev, "Timeout waiting for R/B 0x%x\n",
265 			readl_relaxed(nfc->base + READY_STS_REG));
266 		return -ETIMEDOUT;
267 	}
268 
269 	return 0;
270 }
271 
272 static void anfc_trigger_op(struct arasan_nfc *nfc, struct anfc_op *nfc_op)
273 {
274 	writel_relaxed(nfc_op->pkt_reg, nfc->base + PKT_REG);
275 	writel_relaxed(nfc_op->addr1_reg, nfc->base + MEM_ADDR1_REG);
276 	writel_relaxed(nfc_op->addr2_reg, nfc->base + MEM_ADDR2_REG);
277 	writel_relaxed(nfc_op->cmd_reg, nfc->base + CMD_REG);
278 	writel_relaxed(nfc_op->prog_reg, nfc->base + PROG_REG);
279 }
280 
281 static int anfc_pkt_len_config(unsigned int len, unsigned int *steps,
282 			       unsigned int *pktsize)
283 {
284 	unsigned int nb, sz;
285 
286 	for (nb = 1; nb < ANFC_MAX_STEPS; nb *= 2) {
287 		sz = len / nb;
288 		if (sz <= ANFC_MAX_PKT_SIZE)
289 			break;
290 	}
291 
292 	if (sz * nb != len)
293 		return -ENOTSUPP;
294 
295 	if (steps)
296 		*steps = nb;
297 
298 	if (pktsize)
299 		*pktsize = sz;
300 
301 	return 0;
302 }
303 
304 static bool anfc_is_gpio_cs(struct arasan_nfc *nfc, int nfc_cs)
305 {
306 	return nfc_cs >= 0 && nfc->cs_array[nfc_cs];
307 }
308 
309 static int anfc_relative_to_absolute_cs(struct anand *anand, int num)
310 {
311 	return anand->cs_idx[num];
312 }
313 
314 static void anfc_assert_cs(struct arasan_nfc *nfc, unsigned int nfc_cs_idx)
315 {
316 	/* CS did not change: do nothing */
317 	if (nfc->cur_cs == nfc_cs_idx)
318 		return;
319 
320 	/* Deassert the previous CS if it was a GPIO */
321 	if (anfc_is_gpio_cs(nfc, nfc->cur_cs))
322 		gpiod_set_value_cansleep(nfc->cs_array[nfc->cur_cs], 1);
323 
324 	/* Assert the new one */
325 	if (anfc_is_gpio_cs(nfc, nfc_cs_idx)) {
326 		nfc->native_cs = nfc->spare_cs;
327 		gpiod_set_value_cansleep(nfc->cs_array[nfc_cs_idx], 0);
328 	} else {
329 		nfc->native_cs = nfc_cs_idx;
330 	}
331 
332 	nfc->cur_cs = nfc_cs_idx;
333 }
334 
335 static int anfc_select_target(struct nand_chip *chip, int target)
336 {
337 	struct anand *anand = to_anand(chip);
338 	struct arasan_nfc *nfc = to_anfc(chip->controller);
339 	unsigned int nfc_cs_idx = anfc_relative_to_absolute_cs(anand, target);
340 	int ret;
341 
342 	anfc_assert_cs(nfc, nfc_cs_idx);
343 
344 	/* Update the controller timings and the potential ECC configuration */
345 	writel_relaxed(anand->data_iface, nfc->base + DATA_INTERFACE_REG);
346 	writel_relaxed(anand->timings, nfc->base + TIMING_REG);
347 
348 	/* Update clock frequency */
349 	if (nfc->cur_clk != anand->clk) {
350 		clk_disable_unprepare(nfc->bus_clk);
351 		ret = clk_set_rate(nfc->bus_clk, anand->clk);
352 		if (ret) {
353 			dev_err(nfc->dev, "Failed to change clock rate\n");
354 			return ret;
355 		}
356 
357 		ret = clk_prepare_enable(nfc->bus_clk);
358 		if (ret) {
359 			dev_err(nfc->dev,
360 				"Failed to re-enable the bus clock\n");
361 			return ret;
362 		}
363 
364 		nfc->cur_clk = anand->clk;
365 	}
366 
367 	return 0;
368 }
369 
370 /*
371  * When using the embedded hardware ECC engine, the controller is in charge of
372  * feeding the engine with, first, the ECC residue present in the data array.
373  * A typical read operation is:
374  * 1/ Assert the read operation by sending the relevant command/address cycles
375  *    but targeting the column of the first ECC bytes in the OOB area instead of
376  *    the main data directly.
377  * 2/ After having read the relevant number of ECC bytes, the controller uses
378  *    the RNDOUT/RNDSTART commands which are set into the "ECC Spare Command
379  *    Register" to move the pointer back at the beginning of the main data.
380  * 3/ It will read the content of the main area for a given size (pktsize) and
381  *    will feed the ECC engine with this buffer again.
382  * 4/ The ECC engine derives the ECC bytes for the given data and compare them
383  *    with the ones already received. It eventually trigger status flags and
384  *    then set the "Buffer Read Ready" flag.
385  * 5/ The corrected data is then available for reading from the data port
386  *    register.
387  *
388  * The hardware BCH ECC engine is known to be inconstent in BCH mode and never
389  * reports uncorrectable errors. Because of this bug, we have to use the
390  * software BCH implementation in the read path.
391  */
392 static int anfc_read_page_hw_ecc(struct nand_chip *chip, u8 *buf,
393 				 int oob_required, int page)
394 {
395 	struct arasan_nfc *nfc = to_anfc(chip->controller);
396 	struct mtd_info *mtd = nand_to_mtd(chip);
397 	struct anand *anand = to_anand(chip);
398 	unsigned int len = mtd->writesize + (oob_required ? mtd->oobsize : 0);
399 	unsigned int max_bitflips = 0;
400 	dma_addr_t dma_addr;
401 	int step, ret;
402 	struct anfc_op nfc_op = {
403 		.pkt_reg =
404 			PKT_SIZE(chip->ecc.size) |
405 			PKT_STEPS(chip->ecc.steps),
406 		.addr1_reg =
407 			(page & 0xFF) << (8 * (anand->caddr_cycles)) |
408 			(((page >> 8) & 0xFF) << (8 * (1 + anand->caddr_cycles))),
409 		.addr2_reg =
410 			((page >> 16) & 0xFF) |
411 			ADDR2_STRENGTH(anand->strength) |
412 			ADDR2_CS(nfc->native_cs),
413 		.cmd_reg =
414 			CMD_1(NAND_CMD_READ0) |
415 			CMD_2(NAND_CMD_READSTART) |
416 			CMD_PAGE_SIZE(anand->page_sz) |
417 			CMD_DMA_ENABLE |
418 			CMD_NADDRS(anand->caddr_cycles +
419 				   anand->raddr_cycles),
420 		.prog_reg = PROG_PGRD,
421 	};
422 
423 	dma_addr = dma_map_single(nfc->dev, (void *)buf, len, DMA_FROM_DEVICE);
424 	if (dma_mapping_error(nfc->dev, dma_addr)) {
425 		dev_err(nfc->dev, "Buffer mapping error");
426 		return -EIO;
427 	}
428 
429 	writel_relaxed(lower_32_bits(dma_addr), nfc->base + DMA_ADDR0_REG);
430 	writel_relaxed(upper_32_bits(dma_addr), nfc->base + DMA_ADDR1_REG);
431 
432 	anfc_trigger_op(nfc, &nfc_op);
433 
434 	ret = anfc_wait_for_event(nfc, XFER_COMPLETE);
435 	dma_unmap_single(nfc->dev, dma_addr, len, DMA_FROM_DEVICE);
436 	if (ret) {
437 		dev_err(nfc->dev, "Error reading page %d\n", page);
438 		return ret;
439 	}
440 
441 	/* Store the raw OOB bytes as well */
442 	ret = nand_change_read_column_op(chip, mtd->writesize, chip->oob_poi,
443 					 mtd->oobsize, 0);
444 	if (ret)
445 		return ret;
446 
447 	/*
448 	 * For each step, compute by softare the BCH syndrome over the raw data.
449 	 * Compare the theoretical amount of errors and compare with the
450 	 * hardware engine feedback.
451 	 */
452 	for (step = 0; step < chip->ecc.steps; step++) {
453 		u8 *raw_buf = &buf[step * chip->ecc.size];
454 		unsigned int bit, byte;
455 		int bf, i;
456 
457 		/* Extract the syndrome, it is not necessarily aligned */
458 		memset(anand->hw_ecc, 0, chip->ecc.bytes);
459 		nand_extract_bits(anand->hw_ecc, 0,
460 				  &chip->oob_poi[mtd->oobsize - anand->ecc_total],
461 				  anand->ecc_bits * step, anand->ecc_bits);
462 
463 		bf = bch_decode(anand->bch, raw_buf, chip->ecc.size,
464 				anand->hw_ecc, NULL, NULL, anand->errloc);
465 		if (!bf) {
466 			continue;
467 		} else if (bf > 0) {
468 			for (i = 0; i < bf; i++) {
469 				/* Only correct the data, not the syndrome */
470 				if (anand->errloc[i] < (chip->ecc.size * 8)) {
471 					bit = BIT(anand->errloc[i] & 7);
472 					byte = anand->errloc[i] >> 3;
473 					raw_buf[byte] ^= bit;
474 				}
475 			}
476 
477 			mtd->ecc_stats.corrected += bf;
478 			max_bitflips = max_t(unsigned int, max_bitflips, bf);
479 
480 			continue;
481 		}
482 
483 		bf = nand_check_erased_ecc_chunk(raw_buf, chip->ecc.size,
484 						 NULL, 0, NULL, 0,
485 						 chip->ecc.strength);
486 		if (bf > 0) {
487 			mtd->ecc_stats.corrected += bf;
488 			max_bitflips = max_t(unsigned int, max_bitflips, bf);
489 			memset(raw_buf, 0xFF, chip->ecc.size);
490 		} else if (bf < 0) {
491 			mtd->ecc_stats.failed++;
492 		}
493 	}
494 
495 	return 0;
496 }
497 
498 static int anfc_sel_read_page_hw_ecc(struct nand_chip *chip, u8 *buf,
499 				     int oob_required, int page)
500 {
501 	int ret;
502 
503 	ret = anfc_select_target(chip, chip->cur_cs);
504 	if (ret)
505 		return ret;
506 
507 	return anfc_read_page_hw_ecc(chip, buf, oob_required, page);
508 };
509 
510 static int anfc_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
511 				  int oob_required, int page)
512 {
513 	struct anand *anand = to_anand(chip);
514 	struct arasan_nfc *nfc = to_anfc(chip->controller);
515 	struct mtd_info *mtd = nand_to_mtd(chip);
516 	unsigned int len = mtd->writesize + (oob_required ? mtd->oobsize : 0);
517 	dma_addr_t dma_addr;
518 	int ret;
519 	struct anfc_op nfc_op = {
520 		.pkt_reg =
521 			PKT_SIZE(chip->ecc.size) |
522 			PKT_STEPS(chip->ecc.steps),
523 		.addr1_reg =
524 			(page & 0xFF) << (8 * (anand->caddr_cycles)) |
525 			(((page >> 8) & 0xFF) << (8 * (1 + anand->caddr_cycles))),
526 		.addr2_reg =
527 			((page >> 16) & 0xFF) |
528 			ADDR2_STRENGTH(anand->strength) |
529 			ADDR2_CS(nfc->native_cs),
530 		.cmd_reg =
531 			CMD_1(NAND_CMD_SEQIN) |
532 			CMD_2(NAND_CMD_PAGEPROG) |
533 			CMD_PAGE_SIZE(anand->page_sz) |
534 			CMD_DMA_ENABLE |
535 			CMD_NADDRS(anand->caddr_cycles +
536 				   anand->raddr_cycles) |
537 			CMD_ECC_ENABLE,
538 		.prog_reg = PROG_PGPROG,
539 	};
540 
541 	writel_relaxed(anand->ecc_conf, nfc->base + ECC_CONF_REG);
542 	writel_relaxed(ECC_SP_CMD1(NAND_CMD_RNDIN) |
543 		       ECC_SP_ADDRS(anand->caddr_cycles),
544 		       nfc->base + ECC_SP_REG);
545 
546 	dma_addr = dma_map_single(nfc->dev, (void *)buf, len, DMA_TO_DEVICE);
547 	if (dma_mapping_error(nfc->dev, dma_addr)) {
548 		dev_err(nfc->dev, "Buffer mapping error");
549 		return -EIO;
550 	}
551 
552 	writel_relaxed(lower_32_bits(dma_addr), nfc->base + DMA_ADDR0_REG);
553 	writel_relaxed(upper_32_bits(dma_addr), nfc->base + DMA_ADDR1_REG);
554 
555 	anfc_trigger_op(nfc, &nfc_op);
556 	ret = anfc_wait_for_event(nfc, XFER_COMPLETE);
557 	dma_unmap_single(nfc->dev, dma_addr, len, DMA_TO_DEVICE);
558 	if (ret) {
559 		dev_err(nfc->dev, "Error writing page %d\n", page);
560 		return ret;
561 	}
562 
563 	/* Spare data is not protected */
564 	if (oob_required)
565 		ret = nand_write_oob_std(chip, page);
566 
567 	return ret;
568 }
569 
570 static int anfc_sel_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
571 				      int oob_required, int page)
572 {
573 	int ret;
574 
575 	ret = anfc_select_target(chip, chip->cur_cs);
576 	if (ret)
577 		return ret;
578 
579 	return anfc_write_page_hw_ecc(chip, buf, oob_required, page);
580 };
581 
582 /* NAND framework ->exec_op() hooks and related helpers */
583 static int anfc_parse_instructions(struct nand_chip *chip,
584 				   const struct nand_subop *subop,
585 				   struct anfc_op *nfc_op)
586 {
587 	struct arasan_nfc *nfc = to_anfc(chip->controller);
588 	struct anand *anand = to_anand(chip);
589 	const struct nand_op_instr *instr = NULL;
590 	bool first_cmd = true;
591 	unsigned int op_id;
592 	int ret, i;
593 
594 	memset(nfc_op, 0, sizeof(*nfc_op));
595 	nfc_op->addr2_reg = ADDR2_CS(nfc->native_cs);
596 	nfc_op->cmd_reg = CMD_PAGE_SIZE(anand->page_sz);
597 
598 	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
599 		unsigned int offset, naddrs, pktsize;
600 		const u8 *addrs;
601 		u8 *buf;
602 
603 		instr = &subop->instrs[op_id];
604 
605 		switch (instr->type) {
606 		case NAND_OP_CMD_INSTR:
607 			if (first_cmd)
608 				nfc_op->cmd_reg |= CMD_1(instr->ctx.cmd.opcode);
609 			else
610 				nfc_op->cmd_reg |= CMD_2(instr->ctx.cmd.opcode);
611 
612 			first_cmd = false;
613 			break;
614 
615 		case NAND_OP_ADDR_INSTR:
616 			offset = nand_subop_get_addr_start_off(subop, op_id);
617 			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
618 			addrs = &instr->ctx.addr.addrs[offset];
619 			nfc_op->cmd_reg |= CMD_NADDRS(naddrs);
620 
621 			for (i = 0; i < min(ANFC_MAX_ADDR_CYC, naddrs); i++) {
622 				if (i < 4)
623 					nfc_op->addr1_reg |= (u32)addrs[i] << i * 8;
624 				else
625 					nfc_op->addr2_reg |= addrs[i];
626 			}
627 
628 			break;
629 		case NAND_OP_DATA_IN_INSTR:
630 			nfc_op->read = true;
631 			fallthrough;
632 		case NAND_OP_DATA_OUT_INSTR:
633 			offset = nand_subop_get_data_start_off(subop, op_id);
634 			buf = instr->ctx.data.buf.in;
635 			nfc_op->buf = &buf[offset];
636 			nfc_op->len = nand_subop_get_data_len(subop, op_id);
637 			ret = anfc_pkt_len_config(nfc_op->len, &nfc_op->steps,
638 						  &pktsize);
639 			if (ret)
640 				return ret;
641 
642 			/*
643 			 * Number of DATA cycles must be aligned on 4, this
644 			 * means the controller might read/write more than
645 			 * requested. This is harmless most of the time as extra
646 			 * DATA are discarded in the write path and read pointer
647 			 * adjusted in the read path.
648 			 *
649 			 * FIXME: The core should mark operations where
650 			 * reading/writing more is allowed so the exec_op()
651 			 * implementation can take the right decision when the
652 			 * alignment constraint is not met: adjust the number of
653 			 * DATA cycles when it's allowed, reject the operation
654 			 * otherwise.
655 			 */
656 			nfc_op->pkt_reg |= PKT_SIZE(round_up(pktsize, 4)) |
657 					   PKT_STEPS(nfc_op->steps);
658 			break;
659 		case NAND_OP_WAITRDY_INSTR:
660 			nfc_op->rdy_timeout_ms = instr->ctx.waitrdy.timeout_ms;
661 			break;
662 		}
663 	}
664 
665 	return 0;
666 }
667 
668 static int anfc_rw_pio_op(struct arasan_nfc *nfc, struct anfc_op *nfc_op)
669 {
670 	unsigned int dwords = (nfc_op->len / 4) / nfc_op->steps;
671 	unsigned int last_len = nfc_op->len % 4;
672 	unsigned int offset, dir;
673 	u8 *buf = nfc_op->buf;
674 	int ret, i;
675 
676 	for (i = 0; i < nfc_op->steps; i++) {
677 		dir = nfc_op->read ? READ_READY : WRITE_READY;
678 		ret = anfc_wait_for_event(nfc, dir);
679 		if (ret) {
680 			dev_err(nfc->dev, "PIO %s ready signal not received\n",
681 				nfc_op->read ? "Read" : "Write");
682 			return ret;
683 		}
684 
685 		offset = i * (dwords * 4);
686 		if (nfc_op->read)
687 			ioread32_rep(nfc->base + DATA_PORT_REG, &buf[offset],
688 				     dwords);
689 		else
690 			iowrite32_rep(nfc->base + DATA_PORT_REG, &buf[offset],
691 				      dwords);
692 	}
693 
694 	if (last_len) {
695 		u32 remainder;
696 
697 		offset = nfc_op->len - last_len;
698 
699 		if (nfc_op->read) {
700 			remainder = readl_relaxed(nfc->base + DATA_PORT_REG);
701 			memcpy(&buf[offset], &remainder, last_len);
702 		} else {
703 			memcpy(&remainder, &buf[offset], last_len);
704 			writel_relaxed(remainder, nfc->base + DATA_PORT_REG);
705 		}
706 	}
707 
708 	return anfc_wait_for_event(nfc, XFER_COMPLETE);
709 }
710 
711 static int anfc_misc_data_type_exec(struct nand_chip *chip,
712 				    const struct nand_subop *subop,
713 				    u32 prog_reg)
714 {
715 	struct arasan_nfc *nfc = to_anfc(chip->controller);
716 	struct anfc_op nfc_op = {};
717 	int ret;
718 
719 	ret = anfc_parse_instructions(chip, subop, &nfc_op);
720 	if (ret)
721 		return ret;
722 
723 	nfc_op.prog_reg = prog_reg;
724 	anfc_trigger_op(nfc, &nfc_op);
725 
726 	if (nfc_op.rdy_timeout_ms) {
727 		ret = anfc_wait_for_rb(nfc, chip, nfc_op.rdy_timeout_ms);
728 		if (ret)
729 			return ret;
730 	}
731 
732 	return anfc_rw_pio_op(nfc, &nfc_op);
733 }
734 
735 static int anfc_param_read_type_exec(struct nand_chip *chip,
736 				     const struct nand_subop *subop)
737 {
738 	return anfc_misc_data_type_exec(chip, subop, PROG_RDPARAM);
739 }
740 
741 static int anfc_data_read_type_exec(struct nand_chip *chip,
742 				    const struct nand_subop *subop)
743 {
744 	u32 prog_reg = PROG_PGRD;
745 
746 	/*
747 	 * Experience shows that while in SDR mode sending a CHANGE READ COLUMN
748 	 * command through the READ PAGE "type" always works fine, when in
749 	 * NV-DDR mode the same command simply fails. However, it was also
750 	 * spotted that any CHANGE READ COLUMN command sent through the CHANGE
751 	 * READ COLUMN ENHANCED "type" would correctly work in both cases (SDR
752 	 * and NV-DDR). So, for simplicity, let's program the controller with
753 	 * the CHANGE READ COLUMN ENHANCED "type" whenever we are requested to
754 	 * perform a CHANGE READ COLUMN operation.
755 	 */
756 	if (subop->instrs[0].ctx.cmd.opcode == NAND_CMD_RNDOUT &&
757 	    subop->instrs[2].ctx.cmd.opcode == NAND_CMD_RNDOUTSTART)
758 		prog_reg = PROG_CHG_RD_COL_ENH;
759 
760 	return anfc_misc_data_type_exec(chip, subop, prog_reg);
761 }
762 
763 static int anfc_param_write_type_exec(struct nand_chip *chip,
764 				      const struct nand_subop *subop)
765 {
766 	return anfc_misc_data_type_exec(chip, subop, PROG_SET_FEATURE);
767 }
768 
769 static int anfc_data_write_type_exec(struct nand_chip *chip,
770 				     const struct nand_subop *subop)
771 {
772 	return anfc_misc_data_type_exec(chip, subop, PROG_PGPROG);
773 }
774 
775 static int anfc_misc_zerolen_type_exec(struct nand_chip *chip,
776 				       const struct nand_subop *subop,
777 				       u32 prog_reg)
778 {
779 	struct arasan_nfc *nfc = to_anfc(chip->controller);
780 	struct anfc_op nfc_op = {};
781 	int ret;
782 
783 	ret = anfc_parse_instructions(chip, subop, &nfc_op);
784 	if (ret)
785 		return ret;
786 
787 	nfc_op.prog_reg = prog_reg;
788 	anfc_trigger_op(nfc, &nfc_op);
789 
790 	ret = anfc_wait_for_event(nfc, XFER_COMPLETE);
791 	if (ret)
792 		return ret;
793 
794 	if (nfc_op.rdy_timeout_ms)
795 		ret = anfc_wait_for_rb(nfc, chip, nfc_op.rdy_timeout_ms);
796 
797 	return ret;
798 }
799 
800 static int anfc_status_type_exec(struct nand_chip *chip,
801 				 const struct nand_subop *subop)
802 {
803 	struct arasan_nfc *nfc = to_anfc(chip->controller);
804 	u32 tmp;
805 	int ret;
806 
807 	/* See anfc_check_op() for details about this constraint */
808 	if (subop->instrs[0].ctx.cmd.opcode != NAND_CMD_STATUS)
809 		return -ENOTSUPP;
810 
811 	ret = anfc_misc_zerolen_type_exec(chip, subop, PROG_STATUS);
812 	if (ret)
813 		return ret;
814 
815 	tmp = readl_relaxed(nfc->base + FLASH_STS_REG);
816 	memcpy(subop->instrs[1].ctx.data.buf.in, &tmp, 1);
817 
818 	return 0;
819 }
820 
821 static int anfc_reset_type_exec(struct nand_chip *chip,
822 				const struct nand_subop *subop)
823 {
824 	return anfc_misc_zerolen_type_exec(chip, subop, PROG_RST);
825 }
826 
827 static int anfc_erase_type_exec(struct nand_chip *chip,
828 				const struct nand_subop *subop)
829 {
830 	return anfc_misc_zerolen_type_exec(chip, subop, PROG_ERASE);
831 }
832 
833 static int anfc_wait_type_exec(struct nand_chip *chip,
834 			       const struct nand_subop *subop)
835 {
836 	struct arasan_nfc *nfc = to_anfc(chip->controller);
837 	struct anfc_op nfc_op = {};
838 	int ret;
839 
840 	ret = anfc_parse_instructions(chip, subop, &nfc_op);
841 	if (ret)
842 		return ret;
843 
844 	return anfc_wait_for_rb(nfc, chip, nfc_op.rdy_timeout_ms);
845 }
846 
847 static const struct nand_op_parser anfc_op_parser = NAND_OP_PARSER(
848 	NAND_OP_PARSER_PATTERN(
849 		anfc_param_read_type_exec,
850 		NAND_OP_PARSER_PAT_CMD_ELEM(false),
851 		NAND_OP_PARSER_PAT_ADDR_ELEM(false, ANFC_MAX_ADDR_CYC),
852 		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true),
853 		NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, ANFC_MAX_CHUNK_SIZE)),
854 	NAND_OP_PARSER_PATTERN(
855 		anfc_param_write_type_exec,
856 		NAND_OP_PARSER_PAT_CMD_ELEM(false),
857 		NAND_OP_PARSER_PAT_ADDR_ELEM(false, ANFC_MAX_ADDR_CYC),
858 		NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, ANFC_MAX_PARAM_SIZE)),
859 	NAND_OP_PARSER_PATTERN(
860 		anfc_data_read_type_exec,
861 		NAND_OP_PARSER_PAT_CMD_ELEM(false),
862 		NAND_OP_PARSER_PAT_ADDR_ELEM(false, ANFC_MAX_ADDR_CYC),
863 		NAND_OP_PARSER_PAT_CMD_ELEM(false),
864 		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true),
865 		NAND_OP_PARSER_PAT_DATA_IN_ELEM(true, ANFC_MAX_CHUNK_SIZE)),
866 	NAND_OP_PARSER_PATTERN(
867 		anfc_data_write_type_exec,
868 		NAND_OP_PARSER_PAT_CMD_ELEM(false),
869 		NAND_OP_PARSER_PAT_ADDR_ELEM(false, ANFC_MAX_ADDR_CYC),
870 		NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, ANFC_MAX_CHUNK_SIZE),
871 		NAND_OP_PARSER_PAT_CMD_ELEM(false)),
872 	NAND_OP_PARSER_PATTERN(
873 		anfc_reset_type_exec,
874 		NAND_OP_PARSER_PAT_CMD_ELEM(false),
875 		NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
876 	NAND_OP_PARSER_PATTERN(
877 		anfc_erase_type_exec,
878 		NAND_OP_PARSER_PAT_CMD_ELEM(false),
879 		NAND_OP_PARSER_PAT_ADDR_ELEM(false, ANFC_MAX_ADDR_CYC),
880 		NAND_OP_PARSER_PAT_CMD_ELEM(false),
881 		NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
882 	NAND_OP_PARSER_PATTERN(
883 		anfc_status_type_exec,
884 		NAND_OP_PARSER_PAT_CMD_ELEM(false),
885 		NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, ANFC_MAX_CHUNK_SIZE)),
886 	NAND_OP_PARSER_PATTERN(
887 		anfc_wait_type_exec,
888 		NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
889 	);
890 
891 static int anfc_check_op(struct nand_chip *chip,
892 			 const struct nand_operation *op)
893 {
894 	const struct nand_op_instr *instr;
895 	int op_id;
896 
897 	/*
898 	 * The controller abstracts all the NAND operations and do not support
899 	 * data only operations.
900 	 *
901 	 * TODO: The nand_op_parser framework should be extended to
902 	 * support custom checks on DATA instructions.
903 	 */
904 	for (op_id = 0; op_id < op->ninstrs; op_id++) {
905 		instr = &op->instrs[op_id];
906 
907 		switch (instr->type) {
908 		case NAND_OP_ADDR_INSTR:
909 			if (instr->ctx.addr.naddrs > ANFC_MAX_ADDR_CYC)
910 				return -ENOTSUPP;
911 
912 			break;
913 		case NAND_OP_DATA_IN_INSTR:
914 		case NAND_OP_DATA_OUT_INSTR:
915 			if (instr->ctx.data.len > ANFC_MAX_CHUNK_SIZE)
916 				return -ENOTSUPP;
917 
918 			if (anfc_pkt_len_config(instr->ctx.data.len, 0, 0))
919 				return -ENOTSUPP;
920 
921 			break;
922 		default:
923 			break;
924 		}
925 	}
926 
927 	/*
928 	 * The controller does not allow to proceed with a CMD+DATA_IN cycle
929 	 * manually on the bus by reading data from the data register. Instead,
930 	 * the controller abstract a status read operation with its own status
931 	 * register after ordering a read status operation. Hence, we cannot
932 	 * support any CMD+DATA_IN operation other than a READ STATUS.
933 	 *
934 	 * TODO: The nand_op_parser() framework should be extended to describe
935 	 * fixed patterns instead of open-coding this check here.
936 	 */
937 	if (op->ninstrs == 2 &&
938 	    op->instrs[0].type == NAND_OP_CMD_INSTR &&
939 	    op->instrs[0].ctx.cmd.opcode != NAND_CMD_STATUS &&
940 	    op->instrs[1].type == NAND_OP_DATA_IN_INSTR)
941 		return -ENOTSUPP;
942 
943 	return nand_op_parser_exec_op(chip, &anfc_op_parser, op, true);
944 }
945 
946 static int anfc_exec_op(struct nand_chip *chip,
947 			const struct nand_operation *op,
948 			bool check_only)
949 {
950 	int ret;
951 
952 	if (check_only)
953 		return anfc_check_op(chip, op);
954 
955 	ret = anfc_select_target(chip, op->cs);
956 	if (ret)
957 		return ret;
958 
959 	return nand_op_parser_exec_op(chip, &anfc_op_parser, op, check_only);
960 }
961 
962 static int anfc_setup_interface(struct nand_chip *chip, int target,
963 				const struct nand_interface_config *conf)
964 {
965 	struct anand *anand = to_anand(chip);
966 	struct arasan_nfc *nfc = to_anfc(chip->controller);
967 	struct device_node *np = nfc->dev->of_node;
968 	const struct nand_sdr_timings *sdr;
969 	const struct nand_nvddr_timings *nvddr;
970 	unsigned int tccs_min, dqs_mode, fast_tcad;
971 
972 	if (nand_interface_is_nvddr(conf)) {
973 		nvddr = nand_get_nvddr_timings(conf);
974 		if (IS_ERR(nvddr))
975 			return PTR_ERR(nvddr);
976 
977 		/*
978 		 * The controller only supports data payload requests which are
979 		 * a multiple of 4. In practice, most data accesses are 4-byte
980 		 * aligned and this is not an issue. However, rounding up will
981 		 * simply be refused by the controller if we reached the end of
982 		 * the device *and* we are using the NV-DDR interface(!). In
983 		 * this situation, unaligned data requests ending at the device
984 		 * boundary will confuse the controller and cannot be performed.
985 		 *
986 		 * This is something that happens in nand_read_subpage() when
987 		 * selecting software ECC support and must be avoided.
988 		 */
989 		if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_SOFT)
990 			return -ENOTSUPP;
991 	} else {
992 		sdr = nand_get_sdr_timings(conf);
993 		if (IS_ERR(sdr))
994 			return PTR_ERR(sdr);
995 	}
996 
997 	if (target < 0)
998 		return 0;
999 
1000 	if (nand_interface_is_sdr(conf)) {
1001 		anand->data_iface = DIFACE_SDR |
1002 				    DIFACE_SDR_MODE(conf->timings.mode);
1003 		anand->timings = 0;
1004 	} else {
1005 		anand->data_iface = DIFACE_NVDDR |
1006 				    DIFACE_DDR_MODE(conf->timings.mode);
1007 
1008 		if (conf->timings.nvddr.tCCS_min <= 100000)
1009 			tccs_min = TCCS_TIME_100NS;
1010 		else if (conf->timings.nvddr.tCCS_min <= 200000)
1011 			tccs_min = TCCS_TIME_200NS;
1012 		else if (conf->timings.nvddr.tCCS_min <= 300000)
1013 			tccs_min = TCCS_TIME_300NS;
1014 		else
1015 			tccs_min = TCCS_TIME_500NS;
1016 
1017 		fast_tcad = 0;
1018 		if (conf->timings.nvddr.tCAD_min < 45000)
1019 			fast_tcad = FAST_TCAD;
1020 
1021 		switch (conf->timings.mode) {
1022 		case 5:
1023 		case 4:
1024 			dqs_mode = 2;
1025 			break;
1026 		case 3:
1027 			dqs_mode = 3;
1028 			break;
1029 		case 2:
1030 			dqs_mode = 4;
1031 			break;
1032 		case 1:
1033 			dqs_mode = 5;
1034 			break;
1035 		case 0:
1036 		default:
1037 			dqs_mode = 6;
1038 			break;
1039 		}
1040 
1041 		anand->timings = tccs_min | fast_tcad |
1042 				 DQS_BUFF_SEL_IN(dqs_mode) |
1043 				 DQS_BUFF_SEL_OUT(dqs_mode);
1044 	}
1045 
1046 	if (nand_interface_is_sdr(conf)) {
1047 		anand->clk = ANFC_XLNX_SDR_DFLT_CORE_CLK;
1048 	} else {
1049 		/* ONFI timings are defined in picoseconds */
1050 		anand->clk = div_u64((u64)NSEC_PER_SEC * 1000,
1051 				     conf->timings.nvddr.tCK_min);
1052 	}
1053 
1054 	/*
1055 	 * Due to a hardware bug in the ZynqMP SoC, SDR timing modes 0-1 work
1056 	 * with f > 90MHz (default clock is 100MHz) but signals are unstable
1057 	 * with higher modes. Hence we decrease a little bit the clock rate to
1058 	 * 80MHz when using SDR modes 2-5 with this SoC.
1059 	 */
1060 	if (of_device_is_compatible(np, "xlnx,zynqmp-nand-controller") &&
1061 	    nand_interface_is_sdr(conf) && conf->timings.mode >= 2)
1062 		anand->clk = ANFC_XLNX_SDR_HS_CORE_CLK;
1063 
1064 	return 0;
1065 }
1066 
1067 static int anfc_calc_hw_ecc_bytes(int step_size, int strength)
1068 {
1069 	unsigned int bch_gf_mag, ecc_bits;
1070 
1071 	switch (step_size) {
1072 	case SZ_512:
1073 		bch_gf_mag = 13;
1074 		break;
1075 	case SZ_1K:
1076 		bch_gf_mag = 14;
1077 		break;
1078 	default:
1079 		return -EINVAL;
1080 	}
1081 
1082 	ecc_bits = bch_gf_mag * strength;
1083 
1084 	return DIV_ROUND_UP(ecc_bits, 8);
1085 }
1086 
1087 static const int anfc_hw_ecc_512_strengths[] = {4, 8, 12};
1088 
1089 static const int anfc_hw_ecc_1024_strengths[] = {24};
1090 
1091 static const struct nand_ecc_step_info anfc_hw_ecc_step_infos[] = {
1092 	{
1093 		.stepsize = SZ_512,
1094 		.strengths = anfc_hw_ecc_512_strengths,
1095 		.nstrengths = ARRAY_SIZE(anfc_hw_ecc_512_strengths),
1096 	},
1097 	{
1098 		.stepsize = SZ_1K,
1099 		.strengths = anfc_hw_ecc_1024_strengths,
1100 		.nstrengths = ARRAY_SIZE(anfc_hw_ecc_1024_strengths),
1101 	},
1102 };
1103 
1104 static const struct nand_ecc_caps anfc_hw_ecc_caps = {
1105 	.stepinfos = anfc_hw_ecc_step_infos,
1106 	.nstepinfos = ARRAY_SIZE(anfc_hw_ecc_step_infos),
1107 	.calc_ecc_bytes = anfc_calc_hw_ecc_bytes,
1108 };
1109 
1110 static int anfc_init_hw_ecc_controller(struct arasan_nfc *nfc,
1111 				       struct nand_chip *chip)
1112 {
1113 	struct anand *anand = to_anand(chip);
1114 	struct mtd_info *mtd = nand_to_mtd(chip);
1115 	struct nand_ecc_ctrl *ecc = &chip->ecc;
1116 	unsigned int bch_prim_poly = 0, bch_gf_mag = 0, ecc_offset;
1117 	int ret;
1118 
1119 	switch (mtd->writesize) {
1120 	case SZ_512:
1121 	case SZ_2K:
1122 	case SZ_4K:
1123 	case SZ_8K:
1124 	case SZ_16K:
1125 		break;
1126 	default:
1127 		dev_err(nfc->dev, "Unsupported page size %d\n", mtd->writesize);
1128 		return -EINVAL;
1129 	}
1130 
1131 	ret = nand_ecc_choose_conf(chip, &anfc_hw_ecc_caps, mtd->oobsize);
1132 	if (ret)
1133 		return ret;
1134 
1135 	switch (ecc->strength) {
1136 	case 12:
1137 		anand->strength = 0x1;
1138 		break;
1139 	case 8:
1140 		anand->strength = 0x2;
1141 		break;
1142 	case 4:
1143 		anand->strength = 0x3;
1144 		break;
1145 	case 24:
1146 		anand->strength = 0x4;
1147 		break;
1148 	default:
1149 		dev_err(nfc->dev, "Unsupported strength %d\n", ecc->strength);
1150 		return -EINVAL;
1151 	}
1152 
1153 	switch (ecc->size) {
1154 	case SZ_512:
1155 		bch_gf_mag = 13;
1156 		bch_prim_poly = 0x201b;
1157 		break;
1158 	case SZ_1K:
1159 		bch_gf_mag = 14;
1160 		bch_prim_poly = 0x4443;
1161 		break;
1162 	default:
1163 		dev_err(nfc->dev, "Unsupported step size %d\n", ecc->strength);
1164 		return -EINVAL;
1165 	}
1166 
1167 	mtd_set_ooblayout(mtd, nand_get_large_page_ooblayout());
1168 
1169 	ecc->steps = mtd->writesize / ecc->size;
1170 	ecc->algo = NAND_ECC_ALGO_BCH;
1171 	anand->ecc_bits = bch_gf_mag * ecc->strength;
1172 	ecc->bytes = DIV_ROUND_UP(anand->ecc_bits, 8);
1173 	anand->ecc_total = DIV_ROUND_UP(anand->ecc_bits * ecc->steps, 8);
1174 	ecc_offset = mtd->writesize + mtd->oobsize - anand->ecc_total;
1175 	anand->ecc_conf = ECC_CONF_COL(ecc_offset) |
1176 			  ECC_CONF_LEN(anand->ecc_total) |
1177 			  ECC_CONF_BCH_EN;
1178 
1179 	anand->errloc = devm_kmalloc_array(nfc->dev, ecc->strength,
1180 					   sizeof(*anand->errloc), GFP_KERNEL);
1181 	if (!anand->errloc)
1182 		return -ENOMEM;
1183 
1184 	anand->hw_ecc = devm_kmalloc(nfc->dev, ecc->bytes, GFP_KERNEL);
1185 	if (!anand->hw_ecc)
1186 		return -ENOMEM;
1187 
1188 	/* Enforce bit swapping to fit the hardware */
1189 	anand->bch = bch_init(bch_gf_mag, ecc->strength, bch_prim_poly, true);
1190 	if (!anand->bch)
1191 		return -EINVAL;
1192 
1193 	ecc->read_page = anfc_sel_read_page_hw_ecc;
1194 	ecc->write_page = anfc_sel_write_page_hw_ecc;
1195 
1196 	return 0;
1197 }
1198 
1199 static int anfc_attach_chip(struct nand_chip *chip)
1200 {
1201 	struct anand *anand = to_anand(chip);
1202 	struct arasan_nfc *nfc = to_anfc(chip->controller);
1203 	struct mtd_info *mtd = nand_to_mtd(chip);
1204 	int ret = 0;
1205 
1206 	if (mtd->writesize <= SZ_512)
1207 		anand->caddr_cycles = 1;
1208 	else
1209 		anand->caddr_cycles = 2;
1210 
1211 	if (chip->options & NAND_ROW_ADDR_3)
1212 		anand->raddr_cycles = 3;
1213 	else
1214 		anand->raddr_cycles = 2;
1215 
1216 	switch (mtd->writesize) {
1217 	case 512:
1218 		anand->page_sz = 0;
1219 		break;
1220 	case 1024:
1221 		anand->page_sz = 5;
1222 		break;
1223 	case 2048:
1224 		anand->page_sz = 1;
1225 		break;
1226 	case 4096:
1227 		anand->page_sz = 2;
1228 		break;
1229 	case 8192:
1230 		anand->page_sz = 3;
1231 		break;
1232 	case 16384:
1233 		anand->page_sz = 4;
1234 		break;
1235 	default:
1236 		return -EINVAL;
1237 	}
1238 
1239 	/* These hooks are valid for all ECC providers */
1240 	chip->ecc.read_page_raw = nand_monolithic_read_page_raw;
1241 	chip->ecc.write_page_raw = nand_monolithic_write_page_raw;
1242 
1243 	switch (chip->ecc.engine_type) {
1244 	case NAND_ECC_ENGINE_TYPE_NONE:
1245 	case NAND_ECC_ENGINE_TYPE_SOFT:
1246 	case NAND_ECC_ENGINE_TYPE_ON_DIE:
1247 		break;
1248 	case NAND_ECC_ENGINE_TYPE_ON_HOST:
1249 		ret = anfc_init_hw_ecc_controller(nfc, chip);
1250 		break;
1251 	default:
1252 		dev_err(nfc->dev, "Unsupported ECC mode: %d\n",
1253 			chip->ecc.engine_type);
1254 		return -EINVAL;
1255 	}
1256 
1257 	return ret;
1258 }
1259 
1260 static void anfc_detach_chip(struct nand_chip *chip)
1261 {
1262 	struct anand *anand = to_anand(chip);
1263 
1264 	if (anand->bch)
1265 		bch_free(anand->bch);
1266 }
1267 
1268 static const struct nand_controller_ops anfc_ops = {
1269 	.exec_op = anfc_exec_op,
1270 	.setup_interface = anfc_setup_interface,
1271 	.attach_chip = anfc_attach_chip,
1272 	.detach_chip = anfc_detach_chip,
1273 };
1274 
1275 static int anfc_chip_init(struct arasan_nfc *nfc, struct device_node *np)
1276 {
1277 	struct anand *anand;
1278 	struct nand_chip *chip;
1279 	struct mtd_info *mtd;
1280 	int rb, ret, i;
1281 
1282 	anand = devm_kzalloc(nfc->dev, sizeof(*anand), GFP_KERNEL);
1283 	if (!anand)
1284 		return -ENOMEM;
1285 
1286 	/* Chip-select init */
1287 	anand->ncs_idx = of_property_count_elems_of_size(np, "reg", sizeof(u32));
1288 	if (anand->ncs_idx <= 0 || anand->ncs_idx > nfc->ncs) {
1289 		dev_err(nfc->dev, "Invalid reg property\n");
1290 		return -EINVAL;
1291 	}
1292 
1293 	anand->cs_idx = devm_kcalloc(nfc->dev, anand->ncs_idx,
1294 				     sizeof(*anand->cs_idx), GFP_KERNEL);
1295 	if (!anand->cs_idx)
1296 		return -ENOMEM;
1297 
1298 	for (i = 0; i < anand->ncs_idx; i++) {
1299 		ret = of_property_read_u32_index(np, "reg", i,
1300 						 &anand->cs_idx[i]);
1301 		if (ret) {
1302 			dev_err(nfc->dev, "invalid CS property: %d\n", ret);
1303 			return ret;
1304 		}
1305 	}
1306 
1307 	/* Ready-busy init */
1308 	ret = of_property_read_u32(np, "nand-rb", &rb);
1309 	if (ret)
1310 		return ret;
1311 
1312 	if (rb >= ANFC_MAX_CS) {
1313 		dev_err(nfc->dev, "Wrong RB %d\n", rb);
1314 		return -EINVAL;
1315 	}
1316 
1317 	anand->rb = rb;
1318 
1319 	chip = &anand->chip;
1320 	mtd = nand_to_mtd(chip);
1321 	mtd->dev.parent = nfc->dev;
1322 	chip->controller = &nfc->controller;
1323 	chip->options = NAND_BUSWIDTH_AUTO | NAND_NO_SUBPAGE_WRITE |
1324 			NAND_USES_DMA;
1325 
1326 	nand_set_flash_node(chip, np);
1327 	if (!mtd->name) {
1328 		dev_err(nfc->dev, "NAND label property is mandatory\n");
1329 		return -EINVAL;
1330 	}
1331 
1332 	ret = nand_scan(chip, anand->ncs_idx);
1333 	if (ret) {
1334 		dev_err(nfc->dev, "Scan operation failed\n");
1335 		return ret;
1336 	}
1337 
1338 	ret = mtd_device_register(mtd, NULL, 0);
1339 	if (ret) {
1340 		nand_cleanup(chip);
1341 		return ret;
1342 	}
1343 
1344 	list_add_tail(&anand->node, &nfc->chips);
1345 
1346 	return 0;
1347 }
1348 
1349 static void anfc_chips_cleanup(struct arasan_nfc *nfc)
1350 {
1351 	struct anand *anand, *tmp;
1352 	struct nand_chip *chip;
1353 	int ret;
1354 
1355 	list_for_each_entry_safe(anand, tmp, &nfc->chips, node) {
1356 		chip = &anand->chip;
1357 		ret = mtd_device_unregister(nand_to_mtd(chip));
1358 		WARN_ON(ret);
1359 		nand_cleanup(chip);
1360 		list_del(&anand->node);
1361 	}
1362 }
1363 
1364 static int anfc_chips_init(struct arasan_nfc *nfc)
1365 {
1366 	struct device_node *np = nfc->dev->of_node, *nand_np;
1367 	int nchips = of_get_child_count(np);
1368 	int ret;
1369 
1370 	if (!nchips) {
1371 		dev_err(nfc->dev, "Incorrect number of NAND chips (%d)\n",
1372 			nchips);
1373 		return -EINVAL;
1374 	}
1375 
1376 	for_each_child_of_node(np, nand_np) {
1377 		ret = anfc_chip_init(nfc, nand_np);
1378 		if (ret) {
1379 			of_node_put(nand_np);
1380 			anfc_chips_cleanup(nfc);
1381 			break;
1382 		}
1383 	}
1384 
1385 	return ret;
1386 }
1387 
1388 static void anfc_reset(struct arasan_nfc *nfc)
1389 {
1390 	/* Disable interrupt signals */
1391 	writel_relaxed(0, nfc->base + INTR_SIG_EN_REG);
1392 
1393 	/* Enable interrupt status */
1394 	writel_relaxed(EVENT_MASK, nfc->base + INTR_STS_EN_REG);
1395 
1396 	nfc->cur_cs = -1;
1397 }
1398 
1399 static int anfc_parse_cs(struct arasan_nfc *nfc)
1400 {
1401 	int ret;
1402 
1403 	/* Check the gpio-cs property */
1404 	ret = rawnand_dt_parse_gpio_cs(nfc->dev, &nfc->cs_array, &nfc->ncs);
1405 	if (ret)
1406 		return ret;
1407 
1408 	/*
1409 	 * The controller native CS cannot be both disabled at the same time.
1410 	 * Hence, only one native CS can be used if GPIO CS are needed, so that
1411 	 * the other is selected when a non-native CS must be asserted (not
1412 	 * wired physically or configured as GPIO instead of NAND CS). In this
1413 	 * case, the "not" chosen CS is assigned to nfc->spare_cs and selected
1414 	 * whenever a GPIO CS must be asserted.
1415 	 */
1416 	if (nfc->cs_array && nfc->ncs > 2) {
1417 		if (!nfc->cs_array[0] && !nfc->cs_array[1]) {
1418 			dev_err(nfc->dev,
1419 				"Assign a single native CS when using GPIOs\n");
1420 			return -EINVAL;
1421 		}
1422 
1423 		if (nfc->cs_array[0])
1424 			nfc->spare_cs = 0;
1425 		else
1426 			nfc->spare_cs = 1;
1427 	}
1428 
1429 	if (!nfc->cs_array) {
1430 		nfc->cs_array = anfc_default_cs_array;
1431 		nfc->ncs = ANFC_MAX_CS;
1432 		return 0;
1433 	}
1434 
1435 	return 0;
1436 }
1437 
1438 static int anfc_probe(struct platform_device *pdev)
1439 {
1440 	struct arasan_nfc *nfc;
1441 	int ret;
1442 
1443 	nfc = devm_kzalloc(&pdev->dev, sizeof(*nfc), GFP_KERNEL);
1444 	if (!nfc)
1445 		return -ENOMEM;
1446 
1447 	nfc->dev = &pdev->dev;
1448 	nand_controller_init(&nfc->controller);
1449 	nfc->controller.ops = &anfc_ops;
1450 	INIT_LIST_HEAD(&nfc->chips);
1451 
1452 	nfc->base = devm_platform_ioremap_resource(pdev, 0);
1453 	if (IS_ERR(nfc->base))
1454 		return PTR_ERR(nfc->base);
1455 
1456 	anfc_reset(nfc);
1457 
1458 	nfc->controller_clk = devm_clk_get(&pdev->dev, "controller");
1459 	if (IS_ERR(nfc->controller_clk))
1460 		return PTR_ERR(nfc->controller_clk);
1461 
1462 	nfc->bus_clk = devm_clk_get(&pdev->dev, "bus");
1463 	if (IS_ERR(nfc->bus_clk))
1464 		return PTR_ERR(nfc->bus_clk);
1465 
1466 	ret = clk_prepare_enable(nfc->controller_clk);
1467 	if (ret)
1468 		return ret;
1469 
1470 	ret = clk_prepare_enable(nfc->bus_clk);
1471 	if (ret)
1472 		goto disable_controller_clk;
1473 
1474 	ret = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
1475 	if (ret)
1476 		goto disable_bus_clk;
1477 
1478 	ret = anfc_parse_cs(nfc);
1479 	if (ret)
1480 		goto disable_bus_clk;
1481 
1482 	ret = anfc_chips_init(nfc);
1483 	if (ret)
1484 		goto disable_bus_clk;
1485 
1486 	platform_set_drvdata(pdev, nfc);
1487 
1488 	return 0;
1489 
1490 disable_bus_clk:
1491 	clk_disable_unprepare(nfc->bus_clk);
1492 
1493 disable_controller_clk:
1494 	clk_disable_unprepare(nfc->controller_clk);
1495 
1496 	return ret;
1497 }
1498 
1499 static int anfc_remove(struct platform_device *pdev)
1500 {
1501 	struct arasan_nfc *nfc = platform_get_drvdata(pdev);
1502 
1503 	anfc_chips_cleanup(nfc);
1504 
1505 	clk_disable_unprepare(nfc->bus_clk);
1506 	clk_disable_unprepare(nfc->controller_clk);
1507 
1508 	return 0;
1509 }
1510 
1511 static const struct of_device_id anfc_ids[] = {
1512 	{
1513 		.compatible = "xlnx,zynqmp-nand-controller",
1514 	},
1515 	{
1516 		.compatible = "arasan,nfc-v3p10",
1517 	},
1518 	{}
1519 };
1520 MODULE_DEVICE_TABLE(of, anfc_ids);
1521 
1522 static struct platform_driver anfc_driver = {
1523 	.driver = {
1524 		.name = "arasan-nand-controller",
1525 		.of_match_table = anfc_ids,
1526 	},
1527 	.probe = anfc_probe,
1528 	.remove = anfc_remove,
1529 };
1530 module_platform_driver(anfc_driver);
1531 
1532 MODULE_LICENSE("GPL v2");
1533 MODULE_AUTHOR("Punnaiah Choudary Kalluri <punnaia@xilinx.com>");
1534 MODULE_AUTHOR("Naga Sureshkumar Relli <nagasure@xilinx.com>");
1535 MODULE_AUTHOR("Miquel Raynal <miquel.raynal@bootlin.com>");
1536 MODULE_DESCRIPTION("Arasan NAND Flash Controller Driver");
1537