1# $Id: Kconfig,v 1.11 2005/11/07 11:14:19 gleixner Exp $ 2 3menuconfig MTD 4 tristate "Memory Technology Device (MTD) support" 5 depends on HAS_IOMEM 6 help 7 Memory Technology Devices are flash, RAM and similar chips, often 8 used for solid state file systems on embedded devices. This option 9 will provide the generic support for MTD drivers to register 10 themselves with the kernel and for potential users of MTD devices 11 to enumerate the devices which are present and obtain a handle on 12 them. It will also allow you to select individual drivers for 13 particular hardware and users of MTD devices. If unsure, say N. 14 15if MTD 16 17config MTD_DEBUG 18 bool "Debugging" 19 help 20 This turns on low-level debugging for the entire MTD sub-system. 21 Normally, you should say 'N'. 22 23config MTD_DEBUG_VERBOSE 24 int "Debugging verbosity (0 = quiet, 3 = noisy)" 25 depends on MTD_DEBUG 26 default "0" 27 help 28 Determines the verbosity level of the MTD debugging messages. 29 30config MTD_CONCAT 31 tristate "MTD concatenating support" 32 help 33 Support for concatenating several MTD devices into a single 34 (virtual) one. This allows you to have -for example- a JFFS(2) 35 file system spanning multiple physical flash chips. If unsure, 36 say 'Y'. 37 38config MTD_PARTITIONS 39 bool "MTD partitioning support" 40 help 41 If you have a device which needs to divide its flash chip(s) up 42 into multiple 'partitions', each of which appears to the user as 43 a separate MTD device, you require this option to be enabled. If 44 unsure, say 'Y'. 45 46 Note, however, that you don't need this option for the DiskOnChip 47 devices. Partitioning on NFTL 'devices' is a different - that's the 48 'normal' form of partitioning used on a block device. 49 50config MTD_REDBOOT_PARTS 51 tristate "RedBoot partition table parsing" 52 depends on MTD_PARTITIONS 53 ---help--- 54 RedBoot is a ROM monitor and bootloader which deals with multiple 55 'images' in flash devices by putting a table one of the erase 56 blocks on the device, similar to a partition table, which gives 57 the offsets, lengths and names of all the images stored in the 58 flash. 59 60 If you need code which can detect and parse this table, and register 61 MTD 'partitions' corresponding to each image in the table, enable 62 this option. 63 64 You will still need the parsing functions to be called by the driver 65 for your particular device. It won't happen automatically. The 66 SA1100 map driver (CONFIG_MTD_SA1100) has an option for this, for 67 example. 68 69config MTD_REDBOOT_DIRECTORY_BLOCK 70 int "Location of RedBoot partition table" 71 depends on MTD_REDBOOT_PARTS 72 default "-1" 73 ---help--- 74 This option is the Linux counterpart to the 75 CYGNUM_REDBOOT_FIS_DIRECTORY_BLOCK RedBoot compile time 76 option. 77 78 The option specifies which Flash sectors holds the RedBoot 79 partition table. A zero or positive value gives an absolute 80 erase block number. A negative value specifies a number of 81 sectors before the end of the device. 82 83 For example "2" means block number 2, "-1" means the last 84 block and "-2" means the penultimate block. 85 86config MTD_REDBOOT_PARTS_UNALLOCATED 87 bool "Include unallocated flash regions" 88 depends on MTD_REDBOOT_PARTS 89 help 90 If you need to register each unallocated flash region as a MTD 91 'partition', enable this option. 92 93config MTD_REDBOOT_PARTS_READONLY 94 bool "Force read-only for RedBoot system images" 95 depends on MTD_REDBOOT_PARTS 96 help 97 If you need to force read-only for 'RedBoot', 'RedBoot Config' and 98 'FIS directory' images, enable this option. 99 100config MTD_CMDLINE_PARTS 101 bool "Command line partition table parsing" 102 depends on MTD_PARTITIONS = "y" && MTD = "y" 103 ---help--- 104 Allow generic configuration of the MTD partition tables via the kernel 105 command line. Multiple flash resources are supported for hardware where 106 different kinds of flash memory are available. 107 108 You will still need the parsing functions to be called by the driver 109 for your particular device. It won't happen automatically. The 110 SA1100 map driver (CONFIG_MTD_SA1100) has an option for this, for 111 example. 112 113 The format for the command line is as follows: 114 115 mtdparts=<mtddef>[;<mtddef] 116 <mtddef> := <mtd-id>:<partdef>[,<partdef>] 117 <partdef> := <size>[@offset][<name>][ro] 118 <mtd-id> := unique id used in mapping driver/device 119 <size> := standard linux memsize OR "-" to denote all 120 remaining space 121 <name> := (NAME) 122 123 Due to the way Linux handles the command line, no spaces are 124 allowed in the partition definition, including mtd id's and partition 125 names. 126 127 Examples: 128 129 1 flash resource (mtd-id "sa1100"), with 1 single writable partition: 130 mtdparts=sa1100:- 131 132 Same flash, but 2 named partitions, the first one being read-only: 133 mtdparts=sa1100:256k(ARMboot)ro,-(root) 134 135 If unsure, say 'N'. 136 137config MTD_AFS_PARTS 138 tristate "ARM Firmware Suite partition parsing" 139 depends on ARM && MTD_PARTITIONS 140 ---help--- 141 The ARM Firmware Suite allows the user to divide flash devices into 142 multiple 'images'. Each such image has a header containing its name 143 and offset/size etc. 144 145 If you need code which can detect and parse these tables, and 146 register MTD 'partitions' corresponding to each image detected, 147 enable this option. 148 149 You will still need the parsing functions to be called by the driver 150 for your particular device. It won't happen automatically. The 151 'armflash' map driver (CONFIG_MTD_ARMFLASH) does this, for example. 152 153comment "User Modules And Translation Layers" 154 155config MTD_CHAR 156 tristate "Direct char device access to MTD devices" 157 help 158 This provides a character device for each MTD device present in 159 the system, allowing the user to read and write directly to the 160 memory chips, and also use ioctl() to obtain information about 161 the device, or to erase parts of it. 162 163config MTD_BLKDEVS 164 tristate "Common interface to block layer for MTD 'translation layers'" 165 depends on BLOCK 166 default n 167 168config MTD_BLOCK 169 tristate "Caching block device access to MTD devices" 170 depends on BLOCK 171 select MTD_BLKDEVS 172 ---help--- 173 Although most flash chips have an erase size too large to be useful 174 as block devices, it is possible to use MTD devices which are based 175 on RAM chips in this manner. This block device is a user of MTD 176 devices performing that function. 177 178 At the moment, it is also required for the Journalling Flash File 179 System(s) to obtain a handle on the MTD device when it's mounted 180 (although JFFS and JFFS2 don't actually use any of the functionality 181 of the mtdblock device). 182 183 Later, it may be extended to perform read/erase/modify/write cycles 184 on flash chips to emulate a smaller block size. Needless to say, 185 this is very unsafe, but could be useful for file systems which are 186 almost never written to. 187 188 You do not need this option for use with the DiskOnChip devices. For 189 those, enable NFTL support (CONFIG_NFTL) instead. 190 191config MTD_BLOCK_RO 192 tristate "Readonly block device access to MTD devices" 193 depends on MTD_BLOCK!=y && BLOCK 194 select MTD_BLKDEVS 195 help 196 This allows you to mount read-only file systems (such as cramfs) 197 from an MTD device, without the overhead (and danger) of the caching 198 driver. 199 200 You do not need this option for use with the DiskOnChip devices. For 201 those, enable NFTL support (CONFIG_NFTL) instead. 202 203config FTL 204 tristate "FTL (Flash Translation Layer) support" 205 depends on BLOCK 206 select MTD_BLKDEVS 207 ---help--- 208 This provides support for the original Flash Translation Layer which 209 is part of the PCMCIA specification. It uses a kind of pseudo- 210 file system on a flash device to emulate a block device with 211 512-byte sectors, on top of which you put a 'normal' file system. 212 213 You may find that the algorithms used in this code are patented 214 unless you live in the Free World where software patents aren't 215 legal - in the USA you are only permitted to use this on PCMCIA 216 hardware, although under the terms of the GPL you're obviously 217 permitted to copy, modify and distribute the code as you wish. Just 218 not use it. 219 220config NFTL 221 tristate "NFTL (NAND Flash Translation Layer) support" 222 depends on BLOCK 223 select MTD_BLKDEVS 224 ---help--- 225 This provides support for the NAND Flash Translation Layer which is 226 used on M-Systems' DiskOnChip devices. It uses a kind of pseudo- 227 file system on a flash device to emulate a block device with 228 512-byte sectors, on top of which you put a 'normal' file system. 229 230 You may find that the algorithms used in this code are patented 231 unless you live in the Free World where software patents aren't 232 legal - in the USA you are only permitted to use this on DiskOnChip 233 hardware, although under the terms of the GPL you're obviously 234 permitted to copy, modify and distribute the code as you wish. Just 235 not use it. 236 237config NFTL_RW 238 bool "Write support for NFTL" 239 depends on NFTL 240 help 241 Support for writing to the NAND Flash Translation Layer, as used 242 on the DiskOnChip. 243 244config INFTL 245 tristate "INFTL (Inverse NAND Flash Translation Layer) support" 246 depends on BLOCK 247 select MTD_BLKDEVS 248 ---help--- 249 This provides support for the Inverse NAND Flash Translation 250 Layer which is used on M-Systems' newer DiskOnChip devices. It 251 uses a kind of pseudo-file system on a flash device to emulate 252 a block device with 512-byte sectors, on top of which you put 253 a 'normal' file system. 254 255 You may find that the algorithms used in this code are patented 256 unless you live in the Free World where software patents aren't 257 legal - in the USA you are only permitted to use this on DiskOnChip 258 hardware, although under the terms of the GPL you're obviously 259 permitted to copy, modify and distribute the code as you wish. Just 260 not use it. 261 262config RFD_FTL 263 tristate "Resident Flash Disk (Flash Translation Layer) support" 264 depends on BLOCK 265 select MTD_BLKDEVS 266 ---help--- 267 This provides support for the flash translation layer known 268 as the Resident Flash Disk (RFD), as used by the Embedded BIOS 269 of General Software. There is a blurb at: 270 271 http://www.gensw.com/pages/prod/bios/rfd.htm 272 273config SSFDC 274 tristate "NAND SSFDC (SmartMedia) read only translation layer" 275 depends on BLOCK 276 select MTD_BLKDEVS 277 help 278 This enables read only access to SmartMedia formatted NAND 279 flash. You can mount it with FAT file system. 280 281config MTD_OOPS 282 tristate "Log panic/oops to an MTD buffer" 283 depends on MTD 284 help 285 This enables panic and oops messages to be logged to a circular 286 buffer in a flash partition where it can be read back at some 287 later point. 288 289source "drivers/mtd/chips/Kconfig" 290 291source "drivers/mtd/maps/Kconfig" 292 293source "drivers/mtd/devices/Kconfig" 294 295source "drivers/mtd/nand/Kconfig" 296 297source "drivers/mtd/onenand/Kconfig" 298 299source "drivers/mtd/ubi/Kconfig" 300 301endif # MTD 302