1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Driver for the MMC / SD / SDIO IP found in: 4 * 5 * TC6393XB, TC6391XB, TC6387XB, T7L66XB, ASIC3, SH-Mobile SoCs 6 * 7 * Copyright (C) 2015-19 Renesas Electronics Corporation 8 * Copyright (C) 2016-19 Sang Engineering, Wolfram Sang 9 * Copyright (C) 2017 Horms Solutions, Simon Horman 10 * Copyright (C) 2011 Guennadi Liakhovetski 11 * Copyright (C) 2007 Ian Molton 12 * Copyright (C) 2004 Ian Molton 13 * 14 * This driver draws mainly on scattered spec sheets, Reverse engineering 15 * of the toshiba e800 SD driver and some parts of the 2.4 ASIC3 driver (4 bit 16 * support). (Further 4 bit support from a later datasheet). 17 * 18 * TODO: 19 * Investigate using a workqueue for PIO transfers 20 * Eliminate FIXMEs 21 * Better Power management 22 * Handle MMC errors better 23 * double buffer support 24 * 25 */ 26 27 #include <linux/delay.h> 28 #include <linux/device.h> 29 #include <linux/dma-mapping.h> 30 #include <linux/highmem.h> 31 #include <linux/interrupt.h> 32 #include <linux/io.h> 33 #include <linux/irq.h> 34 #include <linux/mfd/tmio.h> 35 #include <linux/mmc/card.h> 36 #include <linux/mmc/host.h> 37 #include <linux/mmc/mmc.h> 38 #include <linux/mmc/slot-gpio.h> 39 #include <linux/module.h> 40 #include <linux/pagemap.h> 41 #include <linux/platform_device.h> 42 #include <linux/pm_qos.h> 43 #include <linux/pm_runtime.h> 44 #include <linux/regulator/consumer.h> 45 #include <linux/mmc/sdio.h> 46 #include <linux/scatterlist.h> 47 #include <linux/sizes.h> 48 #include <linux/spinlock.h> 49 #include <linux/workqueue.h> 50 51 #include "tmio_mmc.h" 52 53 static inline void tmio_mmc_start_dma(struct tmio_mmc_host *host, 54 struct mmc_data *data) 55 { 56 if (host->dma_ops) 57 host->dma_ops->start(host, data); 58 } 59 60 static inline void tmio_mmc_enable_dma(struct tmio_mmc_host *host, bool enable) 61 { 62 if (host->dma_ops) 63 host->dma_ops->enable(host, enable); 64 } 65 66 static inline void tmio_mmc_request_dma(struct tmio_mmc_host *host, 67 struct tmio_mmc_data *pdata) 68 { 69 if (host->dma_ops) { 70 host->dma_ops->request(host, pdata); 71 } else { 72 host->chan_tx = NULL; 73 host->chan_rx = NULL; 74 } 75 } 76 77 static inline void tmio_mmc_release_dma(struct tmio_mmc_host *host) 78 { 79 if (host->dma_ops) 80 host->dma_ops->release(host); 81 } 82 83 static inline void tmio_mmc_abort_dma(struct tmio_mmc_host *host) 84 { 85 if (host->dma_ops) 86 host->dma_ops->abort(host); 87 } 88 89 static inline void tmio_mmc_dataend_dma(struct tmio_mmc_host *host) 90 { 91 if (host->dma_ops) 92 host->dma_ops->dataend(host); 93 } 94 95 void tmio_mmc_enable_mmc_irqs(struct tmio_mmc_host *host, u32 i) 96 { 97 host->sdcard_irq_mask &= ~(i & TMIO_MASK_IRQ); 98 sd_ctrl_write32_as_16_and_16(host, CTL_IRQ_MASK, host->sdcard_irq_mask); 99 } 100 EXPORT_SYMBOL_GPL(tmio_mmc_enable_mmc_irqs); 101 102 void tmio_mmc_disable_mmc_irqs(struct tmio_mmc_host *host, u32 i) 103 { 104 host->sdcard_irq_mask |= (i & TMIO_MASK_IRQ); 105 sd_ctrl_write32_as_16_and_16(host, CTL_IRQ_MASK, host->sdcard_irq_mask); 106 } 107 EXPORT_SYMBOL_GPL(tmio_mmc_disable_mmc_irqs); 108 109 static void tmio_mmc_ack_mmc_irqs(struct tmio_mmc_host *host, u32 i) 110 { 111 sd_ctrl_write32_as_16_and_16(host, CTL_STATUS, ~i); 112 } 113 114 static void tmio_mmc_init_sg(struct tmio_mmc_host *host, struct mmc_data *data) 115 { 116 host->sg_len = data->sg_len; 117 host->sg_ptr = data->sg; 118 host->sg_orig = data->sg; 119 host->sg_off = 0; 120 } 121 122 static int tmio_mmc_next_sg(struct tmio_mmc_host *host) 123 { 124 host->sg_ptr = sg_next(host->sg_ptr); 125 host->sg_off = 0; 126 return --host->sg_len; 127 } 128 129 #define CMDREQ_TIMEOUT 5000 130 131 static void tmio_mmc_enable_sdio_irq(struct mmc_host *mmc, int enable) 132 { 133 struct tmio_mmc_host *host = mmc_priv(mmc); 134 135 if (enable && !host->sdio_irq_enabled) { 136 u16 sdio_status; 137 138 /* Keep device active while SDIO irq is enabled */ 139 pm_runtime_get_sync(mmc_dev(mmc)); 140 141 host->sdio_irq_enabled = true; 142 host->sdio_irq_mask = TMIO_SDIO_MASK_ALL & ~TMIO_SDIO_STAT_IOIRQ; 143 144 /* Clear obsolete interrupts before enabling */ 145 sdio_status = sd_ctrl_read16(host, CTL_SDIO_STATUS) & ~TMIO_SDIO_MASK_ALL; 146 if (host->pdata->flags & TMIO_MMC_SDIO_STATUS_SETBITS) 147 sdio_status |= TMIO_SDIO_SETBITS_MASK; 148 sd_ctrl_write16(host, CTL_SDIO_STATUS, sdio_status); 149 150 sd_ctrl_write16(host, CTL_SDIO_IRQ_MASK, host->sdio_irq_mask); 151 } else if (!enable && host->sdio_irq_enabled) { 152 host->sdio_irq_mask = TMIO_SDIO_MASK_ALL; 153 sd_ctrl_write16(host, CTL_SDIO_IRQ_MASK, host->sdio_irq_mask); 154 155 host->sdio_irq_enabled = false; 156 pm_runtime_mark_last_busy(mmc_dev(mmc)); 157 pm_runtime_put_autosuspend(mmc_dev(mmc)); 158 } 159 } 160 161 static void tmio_mmc_reset(struct tmio_mmc_host *host) 162 { 163 /* FIXME - should we set stop clock reg here */ 164 sd_ctrl_write16(host, CTL_RESET_SD, 0x0000); 165 usleep_range(10000, 11000); 166 sd_ctrl_write16(host, CTL_RESET_SD, 0x0001); 167 usleep_range(10000, 11000); 168 169 if (host->pdata->flags & TMIO_MMC_SDIO_IRQ) { 170 sd_ctrl_write16(host, CTL_SDIO_IRQ_MASK, host->sdio_irq_mask); 171 sd_ctrl_write16(host, CTL_TRANSACTION_CTL, 0x0001); 172 } 173 } 174 175 static void tmio_mmc_hw_reset(struct mmc_host *mmc) 176 { 177 struct tmio_mmc_host *host = mmc_priv(mmc); 178 179 host->reset(host); 180 181 tmio_mmc_abort_dma(host); 182 183 if (host->hw_reset) 184 host->hw_reset(host); 185 } 186 187 static void tmio_mmc_reset_work(struct work_struct *work) 188 { 189 struct tmio_mmc_host *host = container_of(work, struct tmio_mmc_host, 190 delayed_reset_work.work); 191 struct mmc_request *mrq; 192 unsigned long flags; 193 194 spin_lock_irqsave(&host->lock, flags); 195 mrq = host->mrq; 196 197 /* 198 * is request already finished? Since we use a non-blocking 199 * cancel_delayed_work(), it can happen, that a .set_ios() call preempts 200 * us, so, have to check for IS_ERR(host->mrq) 201 */ 202 if (IS_ERR_OR_NULL(mrq) || 203 time_is_after_jiffies(host->last_req_ts + 204 msecs_to_jiffies(CMDREQ_TIMEOUT))) { 205 spin_unlock_irqrestore(&host->lock, flags); 206 return; 207 } 208 209 dev_warn(&host->pdev->dev, 210 "timeout waiting for hardware interrupt (CMD%u)\n", 211 mrq->cmd->opcode); 212 213 if (host->data) 214 host->data->error = -ETIMEDOUT; 215 else if (host->cmd) 216 host->cmd->error = -ETIMEDOUT; 217 else 218 mrq->cmd->error = -ETIMEDOUT; 219 220 host->cmd = NULL; 221 host->data = NULL; 222 223 spin_unlock_irqrestore(&host->lock, flags); 224 225 tmio_mmc_hw_reset(host->mmc); 226 227 /* Ready for new calls */ 228 host->mrq = NULL; 229 230 mmc_request_done(host->mmc, mrq); 231 } 232 233 /* These are the bitmasks the tmio chip requires to implement the MMC response 234 * types. Note that R1 and R6 are the same in this scheme. */ 235 #define APP_CMD 0x0040 236 #define RESP_NONE 0x0300 237 #define RESP_R1 0x0400 238 #define RESP_R1B 0x0500 239 #define RESP_R2 0x0600 240 #define RESP_R3 0x0700 241 #define DATA_PRESENT 0x0800 242 #define TRANSFER_READ 0x1000 243 #define TRANSFER_MULTI 0x2000 244 #define SECURITY_CMD 0x4000 245 #define NO_CMD12_ISSUE 0x4000 /* TMIO_MMC_HAVE_CMD12_CTRL */ 246 247 static int tmio_mmc_start_command(struct tmio_mmc_host *host, 248 struct mmc_command *cmd) 249 { 250 struct mmc_data *data = host->data; 251 int c = cmd->opcode; 252 253 switch (mmc_resp_type(cmd)) { 254 case MMC_RSP_NONE: c |= RESP_NONE; break; 255 case MMC_RSP_R1: 256 case MMC_RSP_R1_NO_CRC: 257 c |= RESP_R1; break; 258 case MMC_RSP_R1B: c |= RESP_R1B; break; 259 case MMC_RSP_R2: c |= RESP_R2; break; 260 case MMC_RSP_R3: c |= RESP_R3; break; 261 default: 262 pr_debug("Unknown response type %d\n", mmc_resp_type(cmd)); 263 return -EINVAL; 264 } 265 266 host->cmd = cmd; 267 268 /* FIXME - this seems to be ok commented out but the spec suggest this bit 269 * should be set when issuing app commands. 270 * if(cmd->flags & MMC_FLAG_ACMD) 271 * c |= APP_CMD; 272 */ 273 if (data) { 274 c |= DATA_PRESENT; 275 if (data->blocks > 1) { 276 sd_ctrl_write16(host, CTL_STOP_INTERNAL_ACTION, TMIO_STOP_SEC); 277 c |= TRANSFER_MULTI; 278 279 /* 280 * Disable auto CMD12 at IO_RW_EXTENDED and 281 * SET_BLOCK_COUNT when doing multiple block transfer 282 */ 283 if ((host->pdata->flags & TMIO_MMC_HAVE_CMD12_CTRL) && 284 (cmd->opcode == SD_IO_RW_EXTENDED || host->mrq->sbc)) 285 c |= NO_CMD12_ISSUE; 286 } 287 if (data->flags & MMC_DATA_READ) 288 c |= TRANSFER_READ; 289 } 290 291 tmio_mmc_enable_mmc_irqs(host, TMIO_MASK_CMD); 292 293 /* Fire off the command */ 294 sd_ctrl_write32_as_16_and_16(host, CTL_ARG_REG, cmd->arg); 295 sd_ctrl_write16(host, CTL_SD_CMD, c); 296 297 return 0; 298 } 299 300 static void tmio_mmc_transfer_data(struct tmio_mmc_host *host, 301 unsigned short *buf, 302 unsigned int count) 303 { 304 int is_read = host->data->flags & MMC_DATA_READ; 305 u8 *buf8; 306 307 /* 308 * Transfer the data 309 */ 310 if (host->pdata->flags & TMIO_MMC_32BIT_DATA_PORT) { 311 u32 data = 0; 312 u32 *buf32 = (u32 *)buf; 313 314 if (is_read) 315 sd_ctrl_read32_rep(host, CTL_SD_DATA_PORT, buf32, 316 count >> 2); 317 else 318 sd_ctrl_write32_rep(host, CTL_SD_DATA_PORT, buf32, 319 count >> 2); 320 321 /* if count was multiple of 4 */ 322 if (!(count & 0x3)) 323 return; 324 325 buf32 += count >> 2; 326 count %= 4; 327 328 if (is_read) { 329 sd_ctrl_read32_rep(host, CTL_SD_DATA_PORT, &data, 1); 330 memcpy(buf32, &data, count); 331 } else { 332 memcpy(&data, buf32, count); 333 sd_ctrl_write32_rep(host, CTL_SD_DATA_PORT, &data, 1); 334 } 335 336 return; 337 } 338 339 if (is_read) 340 sd_ctrl_read16_rep(host, CTL_SD_DATA_PORT, buf, count >> 1); 341 else 342 sd_ctrl_write16_rep(host, CTL_SD_DATA_PORT, buf, count >> 1); 343 344 /* if count was even number */ 345 if (!(count & 0x1)) 346 return; 347 348 /* if count was odd number */ 349 buf8 = (u8 *)(buf + (count >> 1)); 350 351 /* 352 * FIXME 353 * 354 * driver and this function are assuming that 355 * it is used as little endian 356 */ 357 if (is_read) 358 *buf8 = sd_ctrl_read16(host, CTL_SD_DATA_PORT) & 0xff; 359 else 360 sd_ctrl_write16(host, CTL_SD_DATA_PORT, *buf8); 361 } 362 363 /* 364 * This chip always returns (at least?) as much data as you ask for. 365 * I'm unsure what happens if you ask for less than a block. This should be 366 * looked into to ensure that a funny length read doesn't hose the controller. 367 */ 368 static void tmio_mmc_pio_irq(struct tmio_mmc_host *host) 369 { 370 struct mmc_data *data = host->data; 371 void *sg_virt; 372 unsigned short *buf; 373 unsigned int count; 374 unsigned long flags; 375 376 if (host->dma_on) { 377 pr_err("PIO IRQ in DMA mode!\n"); 378 return; 379 } else if (!data) { 380 pr_debug("Spurious PIO IRQ\n"); 381 return; 382 } 383 384 sg_virt = tmio_mmc_kmap_atomic(host->sg_ptr, &flags); 385 buf = (unsigned short *)(sg_virt + host->sg_off); 386 387 count = host->sg_ptr->length - host->sg_off; 388 if (count > data->blksz) 389 count = data->blksz; 390 391 pr_debug("count: %08x offset: %08x flags %08x\n", 392 count, host->sg_off, data->flags); 393 394 /* Transfer the data */ 395 tmio_mmc_transfer_data(host, buf, count); 396 397 host->sg_off += count; 398 399 tmio_mmc_kunmap_atomic(host->sg_ptr, &flags, sg_virt); 400 401 if (host->sg_off == host->sg_ptr->length) 402 tmio_mmc_next_sg(host); 403 } 404 405 static void tmio_mmc_check_bounce_buffer(struct tmio_mmc_host *host) 406 { 407 if (host->sg_ptr == &host->bounce_sg) { 408 unsigned long flags; 409 void *sg_vaddr = tmio_mmc_kmap_atomic(host->sg_orig, &flags); 410 411 memcpy(sg_vaddr, host->bounce_buf, host->bounce_sg.length); 412 tmio_mmc_kunmap_atomic(host->sg_orig, &flags, sg_vaddr); 413 } 414 } 415 416 /* needs to be called with host->lock held */ 417 void tmio_mmc_do_data_irq(struct tmio_mmc_host *host) 418 { 419 struct mmc_data *data = host->data; 420 struct mmc_command *stop; 421 422 host->data = NULL; 423 424 if (!data) { 425 dev_warn(&host->pdev->dev, "Spurious data end IRQ\n"); 426 return; 427 } 428 stop = data->stop; 429 430 /* FIXME - return correct transfer count on errors */ 431 if (!data->error) 432 data->bytes_xfered = data->blocks * data->blksz; 433 else 434 data->bytes_xfered = 0; 435 436 pr_debug("Completed data request\n"); 437 438 /* 439 * FIXME: other drivers allow an optional stop command of any given type 440 * which we dont do, as the chip can auto generate them. 441 * Perhaps we can be smarter about when to use auto CMD12 and 442 * only issue the auto request when we know this is the desired 443 * stop command, allowing fallback to the stop command the 444 * upper layers expect. For now, we do what works. 445 */ 446 447 if (data->flags & MMC_DATA_READ) { 448 if (host->dma_on) 449 tmio_mmc_check_bounce_buffer(host); 450 dev_dbg(&host->pdev->dev, "Complete Rx request %p\n", 451 host->mrq); 452 } else { 453 dev_dbg(&host->pdev->dev, "Complete Tx request %p\n", 454 host->mrq); 455 } 456 457 if (stop && !host->mrq->sbc) { 458 if (stop->opcode != MMC_STOP_TRANSMISSION || stop->arg) 459 dev_err(&host->pdev->dev, "unsupported stop: CMD%u,0x%x. We did CMD12,0\n", 460 stop->opcode, stop->arg); 461 462 /* fill in response from auto CMD12 */ 463 stop->resp[0] = sd_ctrl_read16_and_16_as_32(host, CTL_RESPONSE); 464 465 sd_ctrl_write16(host, CTL_STOP_INTERNAL_ACTION, 0); 466 } 467 468 schedule_work(&host->done); 469 } 470 EXPORT_SYMBOL_GPL(tmio_mmc_do_data_irq); 471 472 static void tmio_mmc_data_irq(struct tmio_mmc_host *host, unsigned int stat) 473 { 474 struct mmc_data *data; 475 476 spin_lock(&host->lock); 477 data = host->data; 478 479 if (!data) 480 goto out; 481 482 if (stat & TMIO_STAT_CRCFAIL || stat & TMIO_STAT_STOPBIT_ERR || 483 stat & TMIO_STAT_TXUNDERRUN) 484 data->error = -EILSEQ; 485 if (host->dma_on && (data->flags & MMC_DATA_WRITE)) { 486 u32 status = sd_ctrl_read16_and_16_as_32(host, CTL_STATUS); 487 bool done = false; 488 489 /* 490 * Has all data been written out yet? Testing on SuperH showed, 491 * that in most cases the first interrupt comes already with the 492 * BUSY status bit clear, but on some operations, like mount or 493 * in the beginning of a write / sync / umount, there is one 494 * DATAEND interrupt with the BUSY bit set, in this cases 495 * waiting for one more interrupt fixes the problem. 496 */ 497 if (host->pdata->flags & TMIO_MMC_HAS_IDLE_WAIT) { 498 if (status & TMIO_STAT_SCLKDIVEN) 499 done = true; 500 } else { 501 if (!(status & TMIO_STAT_CMD_BUSY)) 502 done = true; 503 } 504 505 if (done) { 506 tmio_mmc_disable_mmc_irqs(host, TMIO_STAT_DATAEND); 507 tmio_mmc_dataend_dma(host); 508 } 509 } else if (host->dma_on && (data->flags & MMC_DATA_READ)) { 510 tmio_mmc_disable_mmc_irqs(host, TMIO_STAT_DATAEND); 511 tmio_mmc_dataend_dma(host); 512 } else { 513 tmio_mmc_do_data_irq(host); 514 tmio_mmc_disable_mmc_irqs(host, TMIO_MASK_READOP | TMIO_MASK_WRITEOP); 515 } 516 out: 517 spin_unlock(&host->lock); 518 } 519 520 static void tmio_mmc_cmd_irq(struct tmio_mmc_host *host, unsigned int stat) 521 { 522 struct mmc_command *cmd = host->cmd; 523 int i, addr; 524 525 spin_lock(&host->lock); 526 527 if (!host->cmd) { 528 pr_debug("Spurious CMD irq\n"); 529 goto out; 530 } 531 532 /* This controller is sicker than the PXA one. Not only do we need to 533 * drop the top 8 bits of the first response word, we also need to 534 * modify the order of the response for short response command types. 535 */ 536 537 for (i = 3, addr = CTL_RESPONSE ; i >= 0 ; i--, addr += 4) 538 cmd->resp[i] = sd_ctrl_read16_and_16_as_32(host, addr); 539 540 if (cmd->flags & MMC_RSP_136) { 541 cmd->resp[0] = (cmd->resp[0] << 8) | (cmd->resp[1] >> 24); 542 cmd->resp[1] = (cmd->resp[1] << 8) | (cmd->resp[2] >> 24); 543 cmd->resp[2] = (cmd->resp[2] << 8) | (cmd->resp[3] >> 24); 544 cmd->resp[3] <<= 8; 545 } else if (cmd->flags & MMC_RSP_R3) { 546 cmd->resp[0] = cmd->resp[3]; 547 } 548 549 if (stat & TMIO_STAT_CMDTIMEOUT) 550 cmd->error = -ETIMEDOUT; 551 else if ((stat & TMIO_STAT_CRCFAIL && cmd->flags & MMC_RSP_CRC) || 552 stat & TMIO_STAT_STOPBIT_ERR || 553 stat & TMIO_STAT_CMD_IDX_ERR) 554 cmd->error = -EILSEQ; 555 556 /* If there is data to handle we enable data IRQs here, and 557 * we will ultimatley finish the request in the data_end handler. 558 * If theres no data or we encountered an error, finish now. 559 */ 560 if (host->data && (!cmd->error || cmd->error == -EILSEQ)) { 561 if (host->data->flags & MMC_DATA_READ) { 562 if (!host->dma_on) { 563 tmio_mmc_enable_mmc_irqs(host, TMIO_MASK_READOP); 564 } else { 565 tmio_mmc_disable_mmc_irqs(host, 566 TMIO_MASK_READOP); 567 tasklet_schedule(&host->dma_issue); 568 } 569 } else { 570 if (!host->dma_on) { 571 tmio_mmc_enable_mmc_irqs(host, TMIO_MASK_WRITEOP); 572 } else { 573 tmio_mmc_disable_mmc_irqs(host, 574 TMIO_MASK_WRITEOP); 575 tasklet_schedule(&host->dma_issue); 576 } 577 } 578 } else { 579 schedule_work(&host->done); 580 } 581 582 out: 583 spin_unlock(&host->lock); 584 } 585 586 static bool __tmio_mmc_card_detect_irq(struct tmio_mmc_host *host, 587 int ireg, int status) 588 { 589 struct mmc_host *mmc = host->mmc; 590 591 /* Card insert / remove attempts */ 592 if (ireg & (TMIO_STAT_CARD_INSERT | TMIO_STAT_CARD_REMOVE)) { 593 tmio_mmc_ack_mmc_irqs(host, TMIO_STAT_CARD_INSERT | 594 TMIO_STAT_CARD_REMOVE); 595 if ((((ireg & TMIO_STAT_CARD_REMOVE) && mmc->card) || 596 ((ireg & TMIO_STAT_CARD_INSERT) && !mmc->card)) && 597 !work_pending(&mmc->detect.work)) 598 mmc_detect_change(host->mmc, msecs_to_jiffies(100)); 599 return true; 600 } 601 602 return false; 603 } 604 605 static bool __tmio_mmc_sdcard_irq(struct tmio_mmc_host *host, int ireg, 606 int status) 607 { 608 /* Command completion */ 609 if (ireg & (TMIO_STAT_CMDRESPEND | TMIO_STAT_CMDTIMEOUT)) { 610 tmio_mmc_ack_mmc_irqs(host, TMIO_STAT_CMDRESPEND | 611 TMIO_STAT_CMDTIMEOUT); 612 tmio_mmc_cmd_irq(host, status); 613 return true; 614 } 615 616 /* Data transfer */ 617 if (ireg & (TMIO_STAT_RXRDY | TMIO_STAT_TXRQ)) { 618 tmio_mmc_ack_mmc_irqs(host, TMIO_STAT_RXRDY | TMIO_STAT_TXRQ); 619 tmio_mmc_pio_irq(host); 620 return true; 621 } 622 623 /* Data transfer completion */ 624 if (ireg & TMIO_STAT_DATAEND) { 625 tmio_mmc_ack_mmc_irqs(host, TMIO_STAT_DATAEND); 626 tmio_mmc_data_irq(host, status); 627 return true; 628 } 629 630 return false; 631 } 632 633 static bool __tmio_mmc_sdio_irq(struct tmio_mmc_host *host) 634 { 635 struct mmc_host *mmc = host->mmc; 636 struct tmio_mmc_data *pdata = host->pdata; 637 unsigned int ireg, status; 638 unsigned int sdio_status; 639 640 if (!(pdata->flags & TMIO_MMC_SDIO_IRQ)) 641 return false; 642 643 status = sd_ctrl_read16(host, CTL_SDIO_STATUS); 644 ireg = status & TMIO_SDIO_MASK_ALL & ~host->sdio_irq_mask; 645 646 sdio_status = status & ~TMIO_SDIO_MASK_ALL; 647 if (pdata->flags & TMIO_MMC_SDIO_STATUS_SETBITS) 648 sdio_status |= TMIO_SDIO_SETBITS_MASK; 649 650 sd_ctrl_write16(host, CTL_SDIO_STATUS, sdio_status); 651 652 if (mmc->caps & MMC_CAP_SDIO_IRQ && ireg & TMIO_SDIO_STAT_IOIRQ) 653 mmc_signal_sdio_irq(mmc); 654 655 return ireg; 656 } 657 658 irqreturn_t tmio_mmc_irq(int irq, void *devid) 659 { 660 struct tmio_mmc_host *host = devid; 661 unsigned int ireg, status; 662 663 status = sd_ctrl_read16_and_16_as_32(host, CTL_STATUS); 664 ireg = status & TMIO_MASK_IRQ & ~host->sdcard_irq_mask; 665 666 /* Clear the status except the interrupt status */ 667 sd_ctrl_write32_as_16_and_16(host, CTL_STATUS, TMIO_MASK_IRQ); 668 669 if (__tmio_mmc_card_detect_irq(host, ireg, status)) 670 return IRQ_HANDLED; 671 if (__tmio_mmc_sdcard_irq(host, ireg, status)) 672 return IRQ_HANDLED; 673 674 if (__tmio_mmc_sdio_irq(host)) 675 return IRQ_HANDLED; 676 677 return IRQ_NONE; 678 } 679 EXPORT_SYMBOL_GPL(tmio_mmc_irq); 680 681 static int tmio_mmc_start_data(struct tmio_mmc_host *host, 682 struct mmc_data *data) 683 { 684 struct tmio_mmc_data *pdata = host->pdata; 685 686 pr_debug("setup data transfer: blocksize %08x nr_blocks %d\n", 687 data->blksz, data->blocks); 688 689 /* Some hardware cannot perform 2 byte requests in 4/8 bit mode */ 690 if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4 || 691 host->mmc->ios.bus_width == MMC_BUS_WIDTH_8) { 692 int blksz_2bytes = pdata->flags & TMIO_MMC_BLKSZ_2BYTES; 693 694 if (data->blksz < 2 || (data->blksz < 4 && !blksz_2bytes)) { 695 pr_err("%s: %d byte block unsupported in 4/8 bit mode\n", 696 mmc_hostname(host->mmc), data->blksz); 697 return -EINVAL; 698 } 699 } 700 701 tmio_mmc_init_sg(host, data); 702 host->data = data; 703 host->dma_on = false; 704 705 /* Set transfer length / blocksize */ 706 sd_ctrl_write16(host, CTL_SD_XFER_LEN, data->blksz); 707 if (host->mmc->max_blk_count >= SZ_64K) 708 sd_ctrl_write32(host, CTL_XFER_BLK_COUNT, data->blocks); 709 else 710 sd_ctrl_write16(host, CTL_XFER_BLK_COUNT, data->blocks); 711 712 tmio_mmc_start_dma(host, data); 713 714 return 0; 715 } 716 717 static int tmio_mmc_execute_tuning(struct mmc_host *mmc, u32 opcode) 718 { 719 struct tmio_mmc_host *host = mmc_priv(mmc); 720 int i, ret = 0; 721 722 if (!host->init_tuning || !host->select_tuning) 723 /* Tuning is not supported */ 724 goto out; 725 726 host->tap_num = host->init_tuning(host); 727 if (!host->tap_num) 728 /* Tuning is not supported */ 729 goto out; 730 731 if (host->tap_num * 2 >= sizeof(host->taps) * BITS_PER_BYTE) { 732 dev_warn_once(&host->pdev->dev, 733 "Too many taps, skipping tuning. Please consider updating size of taps field of tmio_mmc_host\n"); 734 goto out; 735 } 736 737 bitmap_zero(host->taps, host->tap_num * 2); 738 739 /* Issue CMD19 twice for each tap */ 740 for (i = 0; i < 2 * host->tap_num; i++) { 741 if (host->prepare_tuning) 742 host->prepare_tuning(host, i % host->tap_num); 743 744 ret = mmc_send_tuning(mmc, opcode, NULL); 745 if (ret == 0) 746 set_bit(i, host->taps); 747 } 748 749 ret = host->select_tuning(host); 750 751 out: 752 if (ret < 0) { 753 dev_warn(&host->pdev->dev, "Tuning procedure failed\n"); 754 tmio_mmc_hw_reset(mmc); 755 } 756 757 return ret; 758 } 759 760 static void tmio_process_mrq(struct tmio_mmc_host *host, 761 struct mmc_request *mrq) 762 { 763 struct mmc_command *cmd; 764 int ret; 765 766 if (mrq->sbc && host->cmd != mrq->sbc) { 767 cmd = mrq->sbc; 768 } else { 769 cmd = mrq->cmd; 770 if (mrq->data) { 771 ret = tmio_mmc_start_data(host, mrq->data); 772 if (ret) 773 goto fail; 774 } 775 } 776 777 ret = tmio_mmc_start_command(host, cmd); 778 if (ret) 779 goto fail; 780 781 schedule_delayed_work(&host->delayed_reset_work, 782 msecs_to_jiffies(CMDREQ_TIMEOUT)); 783 return; 784 785 fail: 786 host->mrq = NULL; 787 mrq->cmd->error = ret; 788 mmc_request_done(host->mmc, mrq); 789 } 790 791 /* Process requests from the MMC layer */ 792 static void tmio_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq) 793 { 794 struct tmio_mmc_host *host = mmc_priv(mmc); 795 unsigned long flags; 796 797 spin_lock_irqsave(&host->lock, flags); 798 799 if (host->mrq) { 800 pr_debug("request not null\n"); 801 if (IS_ERR(host->mrq)) { 802 spin_unlock_irqrestore(&host->lock, flags); 803 mrq->cmd->error = -EAGAIN; 804 mmc_request_done(mmc, mrq); 805 return; 806 } 807 } 808 809 host->last_req_ts = jiffies; 810 wmb(); 811 host->mrq = mrq; 812 813 spin_unlock_irqrestore(&host->lock, flags); 814 815 tmio_process_mrq(host, mrq); 816 } 817 818 static void tmio_mmc_finish_request(struct tmio_mmc_host *host) 819 { 820 struct mmc_request *mrq; 821 unsigned long flags; 822 823 spin_lock_irqsave(&host->lock, flags); 824 825 mrq = host->mrq; 826 if (IS_ERR_OR_NULL(mrq)) { 827 spin_unlock_irqrestore(&host->lock, flags); 828 return; 829 } 830 831 /* If not SET_BLOCK_COUNT, clear old data */ 832 if (host->cmd != mrq->sbc) { 833 host->cmd = NULL; 834 host->data = NULL; 835 host->mrq = NULL; 836 } 837 838 cancel_delayed_work(&host->delayed_reset_work); 839 840 spin_unlock_irqrestore(&host->lock, flags); 841 842 if (mrq->cmd->error || (mrq->data && mrq->data->error)) 843 tmio_mmc_abort_dma(host); 844 845 /* SCC error means retune, but executed command was still successful */ 846 if (host->check_scc_error && host->check_scc_error(host)) 847 mmc_retune_needed(host->mmc); 848 849 /* If SET_BLOCK_COUNT, continue with main command */ 850 if (host->mrq && !mrq->cmd->error) { 851 tmio_process_mrq(host, mrq); 852 return; 853 } 854 855 mmc_request_done(host->mmc, mrq); 856 } 857 858 static void tmio_mmc_done_work(struct work_struct *work) 859 { 860 struct tmio_mmc_host *host = container_of(work, struct tmio_mmc_host, 861 done); 862 tmio_mmc_finish_request(host); 863 } 864 865 static void tmio_mmc_power_on(struct tmio_mmc_host *host, unsigned short vdd) 866 { 867 struct mmc_host *mmc = host->mmc; 868 int ret = 0; 869 870 /* .set_ios() is returning void, so, no chance to report an error */ 871 872 if (host->set_pwr) 873 host->set_pwr(host->pdev, 1); 874 875 if (!IS_ERR(mmc->supply.vmmc)) { 876 ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd); 877 /* 878 * Attention: empiric value. With a b43 WiFi SDIO card this 879 * delay proved necessary for reliable card-insertion probing. 880 * 100us were not enough. Is this the same 140us delay, as in 881 * tmio_mmc_set_ios()? 882 */ 883 usleep_range(200, 300); 884 } 885 /* 886 * It seems, VccQ should be switched on after Vcc, this is also what the 887 * omap_hsmmc.c driver does. 888 */ 889 if (!IS_ERR(mmc->supply.vqmmc) && !ret) { 890 ret = regulator_enable(mmc->supply.vqmmc); 891 usleep_range(200, 300); 892 } 893 894 if (ret < 0) 895 dev_dbg(&host->pdev->dev, "Regulators failed to power up: %d\n", 896 ret); 897 } 898 899 static void tmio_mmc_power_off(struct tmio_mmc_host *host) 900 { 901 struct mmc_host *mmc = host->mmc; 902 903 if (!IS_ERR(mmc->supply.vqmmc)) 904 regulator_disable(mmc->supply.vqmmc); 905 906 if (!IS_ERR(mmc->supply.vmmc)) 907 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0); 908 909 if (host->set_pwr) 910 host->set_pwr(host->pdev, 0); 911 } 912 913 static void tmio_mmc_set_bus_width(struct tmio_mmc_host *host, 914 unsigned char bus_width) 915 { 916 u16 reg = sd_ctrl_read16(host, CTL_SD_MEM_CARD_OPT) 917 & ~(CARD_OPT_WIDTH | CARD_OPT_WIDTH8); 918 919 /* reg now applies to MMC_BUS_WIDTH_4 */ 920 if (bus_width == MMC_BUS_WIDTH_1) 921 reg |= CARD_OPT_WIDTH; 922 else if (bus_width == MMC_BUS_WIDTH_8) 923 reg |= CARD_OPT_WIDTH8; 924 925 sd_ctrl_write16(host, CTL_SD_MEM_CARD_OPT, reg); 926 } 927 928 /* Set MMC clock / power. 929 * Note: This controller uses a simple divider scheme therefore it cannot 930 * run a MMC card at full speed (20MHz). The max clock is 24MHz on SD, but as 931 * MMC wont run that fast, it has to be clocked at 12MHz which is the next 932 * slowest setting. 933 */ 934 static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) 935 { 936 struct tmio_mmc_host *host = mmc_priv(mmc); 937 struct device *dev = &host->pdev->dev; 938 unsigned long flags; 939 940 mutex_lock(&host->ios_lock); 941 942 spin_lock_irqsave(&host->lock, flags); 943 if (host->mrq) { 944 if (IS_ERR(host->mrq)) { 945 dev_dbg(dev, 946 "%s.%d: concurrent .set_ios(), clk %u, mode %u\n", 947 current->comm, task_pid_nr(current), 948 ios->clock, ios->power_mode); 949 host->mrq = ERR_PTR(-EINTR); 950 } else { 951 dev_dbg(dev, 952 "%s.%d: CMD%u active since %lu, now %lu!\n", 953 current->comm, task_pid_nr(current), 954 host->mrq->cmd->opcode, host->last_req_ts, 955 jiffies); 956 } 957 spin_unlock_irqrestore(&host->lock, flags); 958 959 mutex_unlock(&host->ios_lock); 960 return; 961 } 962 963 host->mrq = ERR_PTR(-EBUSY); 964 965 spin_unlock_irqrestore(&host->lock, flags); 966 967 switch (ios->power_mode) { 968 case MMC_POWER_OFF: 969 tmio_mmc_power_off(host); 970 host->set_clock(host, 0); 971 break; 972 case MMC_POWER_UP: 973 tmio_mmc_power_on(host, ios->vdd); 974 host->set_clock(host, ios->clock); 975 tmio_mmc_set_bus_width(host, ios->bus_width); 976 break; 977 case MMC_POWER_ON: 978 host->set_clock(host, ios->clock); 979 tmio_mmc_set_bus_width(host, ios->bus_width); 980 break; 981 } 982 983 /* Let things settle. delay taken from winCE driver */ 984 usleep_range(140, 200); 985 if (PTR_ERR(host->mrq) == -EINTR) 986 dev_dbg(&host->pdev->dev, 987 "%s.%d: IOS interrupted: clk %u, mode %u", 988 current->comm, task_pid_nr(current), 989 ios->clock, ios->power_mode); 990 host->mrq = NULL; 991 992 host->clk_cache = ios->clock; 993 994 mutex_unlock(&host->ios_lock); 995 } 996 997 static int tmio_mmc_get_ro(struct mmc_host *mmc) 998 { 999 struct tmio_mmc_host *host = mmc_priv(mmc); 1000 1001 return !(sd_ctrl_read16_and_16_as_32(host, CTL_STATUS) & 1002 TMIO_STAT_WRPROTECT); 1003 } 1004 1005 static int tmio_mmc_get_cd(struct mmc_host *mmc) 1006 { 1007 struct tmio_mmc_host *host = mmc_priv(mmc); 1008 1009 return !!(sd_ctrl_read16_and_16_as_32(host, CTL_STATUS) & 1010 TMIO_STAT_SIGSTATE); 1011 } 1012 1013 static int tmio_multi_io_quirk(struct mmc_card *card, 1014 unsigned int direction, int blk_size) 1015 { 1016 struct tmio_mmc_host *host = mmc_priv(card->host); 1017 1018 if (host->multi_io_quirk) 1019 return host->multi_io_quirk(card, direction, blk_size); 1020 1021 return blk_size; 1022 } 1023 1024 static int tmio_mmc_prepare_hs400_tuning(struct mmc_host *mmc, 1025 struct mmc_ios *ios) 1026 { 1027 struct tmio_mmc_host *host = mmc_priv(mmc); 1028 1029 if (host->prepare_hs400_tuning) 1030 host->prepare_hs400_tuning(host); 1031 1032 return 0; 1033 } 1034 1035 static void tmio_mmc_hs400_downgrade(struct mmc_host *mmc) 1036 { 1037 struct tmio_mmc_host *host = mmc_priv(mmc); 1038 1039 if (host->hs400_downgrade) 1040 host->hs400_downgrade(host); 1041 } 1042 1043 static void tmio_mmc_hs400_complete(struct mmc_host *mmc) 1044 { 1045 struct tmio_mmc_host *host = mmc_priv(mmc); 1046 1047 if (host->hs400_complete) 1048 host->hs400_complete(host); 1049 } 1050 1051 static const struct mmc_host_ops tmio_mmc_ops = { 1052 .request = tmio_mmc_request, 1053 .set_ios = tmio_mmc_set_ios, 1054 .get_ro = tmio_mmc_get_ro, 1055 .get_cd = tmio_mmc_get_cd, 1056 .enable_sdio_irq = tmio_mmc_enable_sdio_irq, 1057 .multi_io_quirk = tmio_multi_io_quirk, 1058 .hw_reset = tmio_mmc_hw_reset, 1059 .execute_tuning = tmio_mmc_execute_tuning, 1060 .prepare_hs400_tuning = tmio_mmc_prepare_hs400_tuning, 1061 .hs400_downgrade = tmio_mmc_hs400_downgrade, 1062 .hs400_complete = tmio_mmc_hs400_complete, 1063 }; 1064 1065 static int tmio_mmc_init_ocr(struct tmio_mmc_host *host) 1066 { 1067 struct tmio_mmc_data *pdata = host->pdata; 1068 struct mmc_host *mmc = host->mmc; 1069 int err; 1070 1071 err = mmc_regulator_get_supply(mmc); 1072 if (err) 1073 return err; 1074 1075 /* use ocr_mask if no regulator */ 1076 if (!mmc->ocr_avail) 1077 mmc->ocr_avail = pdata->ocr_mask; 1078 1079 /* 1080 * try again. 1081 * There is possibility that regulator has not been probed 1082 */ 1083 if (!mmc->ocr_avail) 1084 return -EPROBE_DEFER; 1085 1086 return 0; 1087 } 1088 1089 static void tmio_mmc_of_parse(struct platform_device *pdev, 1090 struct mmc_host *mmc) 1091 { 1092 const struct device_node *np = pdev->dev.of_node; 1093 1094 if (!np) 1095 return; 1096 1097 /* 1098 * DEPRECATED: 1099 * For new platforms, please use "disable-wp" instead of 1100 * "toshiba,mmc-wrprotect-disable" 1101 */ 1102 if (of_get_property(np, "toshiba,mmc-wrprotect-disable", NULL)) 1103 mmc->caps2 |= MMC_CAP2_NO_WRITE_PROTECT; 1104 } 1105 1106 struct tmio_mmc_host *tmio_mmc_host_alloc(struct platform_device *pdev, 1107 struct tmio_mmc_data *pdata) 1108 { 1109 struct tmio_mmc_host *host; 1110 struct mmc_host *mmc; 1111 struct resource *res; 1112 void __iomem *ctl; 1113 int ret; 1114 1115 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1116 ctl = devm_ioremap_resource(&pdev->dev, res); 1117 if (IS_ERR(ctl)) 1118 return ERR_CAST(ctl); 1119 1120 mmc = mmc_alloc_host(sizeof(struct tmio_mmc_host), &pdev->dev); 1121 if (!mmc) 1122 return ERR_PTR(-ENOMEM); 1123 1124 host = mmc_priv(mmc); 1125 host->ctl = ctl; 1126 host->mmc = mmc; 1127 host->pdev = pdev; 1128 host->pdata = pdata; 1129 host->ops = tmio_mmc_ops; 1130 mmc->ops = &host->ops; 1131 1132 ret = mmc_of_parse(host->mmc); 1133 if (ret) { 1134 host = ERR_PTR(ret); 1135 goto free; 1136 } 1137 1138 tmio_mmc_of_parse(pdev, mmc); 1139 1140 platform_set_drvdata(pdev, host); 1141 1142 return host; 1143 free: 1144 mmc_free_host(mmc); 1145 1146 return host; 1147 } 1148 EXPORT_SYMBOL_GPL(tmio_mmc_host_alloc); 1149 1150 void tmio_mmc_host_free(struct tmio_mmc_host *host) 1151 { 1152 mmc_free_host(host->mmc); 1153 } 1154 EXPORT_SYMBOL_GPL(tmio_mmc_host_free); 1155 1156 int tmio_mmc_host_probe(struct tmio_mmc_host *_host) 1157 { 1158 struct platform_device *pdev = _host->pdev; 1159 struct tmio_mmc_data *pdata = _host->pdata; 1160 struct mmc_host *mmc = _host->mmc; 1161 int ret; 1162 1163 /* 1164 * Check the sanity of mmc->f_min to prevent host->set_clock() from 1165 * looping forever... 1166 */ 1167 if (mmc->f_min == 0) 1168 return -EINVAL; 1169 1170 if (!(pdata->flags & TMIO_MMC_HAS_IDLE_WAIT)) 1171 _host->write16_hook = NULL; 1172 1173 _host->set_pwr = pdata->set_pwr; 1174 1175 ret = tmio_mmc_init_ocr(_host); 1176 if (ret < 0) 1177 return ret; 1178 1179 /* 1180 * Look for a card detect GPIO, if it fails with anything 1181 * else than a probe deferral, just live without it. 1182 */ 1183 ret = mmc_gpiod_request_cd(mmc, "cd", 0, false, 0, NULL); 1184 if (ret == -EPROBE_DEFER) 1185 return ret; 1186 1187 mmc->caps |= MMC_CAP_4_BIT_DATA | pdata->capabilities; 1188 mmc->caps2 |= pdata->capabilities2; 1189 mmc->max_segs = pdata->max_segs ? : 32; 1190 mmc->max_blk_size = TMIO_MAX_BLK_SIZE; 1191 mmc->max_blk_count = pdata->max_blk_count ? : 1192 (PAGE_SIZE / mmc->max_blk_size) * mmc->max_segs; 1193 mmc->max_req_size = min_t(size_t, 1194 mmc->max_blk_size * mmc->max_blk_count, 1195 dma_max_mapping_size(&pdev->dev)); 1196 mmc->max_seg_size = mmc->max_req_size; 1197 1198 if (mmc_can_gpio_ro(mmc)) 1199 _host->ops.get_ro = mmc_gpio_get_ro; 1200 1201 if (mmc_can_gpio_cd(mmc)) 1202 _host->ops.get_cd = mmc_gpio_get_cd; 1203 1204 _host->native_hotplug = !(mmc_can_gpio_cd(mmc) || 1205 mmc->caps & MMC_CAP_NEEDS_POLL || 1206 !mmc_card_is_removable(mmc)); 1207 1208 if (!_host->reset) 1209 _host->reset = tmio_mmc_reset; 1210 1211 /* 1212 * On Gen2+, eMMC with NONREMOVABLE currently fails because native 1213 * hotplug gets disabled. It seems RuntimePM related yet we need further 1214 * research. Since we are planning a PM overhaul anyway, let's enforce 1215 * for now the device being active by enabling native hotplug always. 1216 */ 1217 if (pdata->flags & TMIO_MMC_MIN_RCAR2) 1218 _host->native_hotplug = true; 1219 1220 /* 1221 * While using internal tmio hardware logic for card detection, we need 1222 * to ensure it stays powered for it to work. 1223 */ 1224 if (_host->native_hotplug) 1225 pm_runtime_get_noresume(&pdev->dev); 1226 1227 _host->sdio_irq_enabled = false; 1228 if (pdata->flags & TMIO_MMC_SDIO_IRQ) 1229 _host->sdio_irq_mask = TMIO_SDIO_MASK_ALL; 1230 1231 _host->set_clock(_host, 0); 1232 tmio_mmc_hw_reset(mmc); 1233 1234 _host->sdcard_irq_mask = sd_ctrl_read16_and_16_as_32(_host, CTL_IRQ_MASK); 1235 tmio_mmc_disable_mmc_irqs(_host, TMIO_MASK_ALL); 1236 1237 if (_host->native_hotplug) 1238 tmio_mmc_enable_mmc_irqs(_host, 1239 TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT); 1240 1241 spin_lock_init(&_host->lock); 1242 mutex_init(&_host->ios_lock); 1243 1244 /* Init delayed work for request timeouts */ 1245 INIT_DELAYED_WORK(&_host->delayed_reset_work, tmio_mmc_reset_work); 1246 INIT_WORK(&_host->done, tmio_mmc_done_work); 1247 1248 /* See if we also get DMA */ 1249 tmio_mmc_request_dma(_host, pdata); 1250 1251 pm_runtime_set_autosuspend_delay(&pdev->dev, 50); 1252 pm_runtime_use_autosuspend(&pdev->dev); 1253 pm_runtime_enable(&pdev->dev); 1254 pm_runtime_get_sync(&pdev->dev); 1255 1256 ret = mmc_add_host(mmc); 1257 if (ret) 1258 goto remove_host; 1259 1260 dev_pm_qos_expose_latency_limit(&pdev->dev, 100); 1261 pm_runtime_put(&pdev->dev); 1262 1263 return 0; 1264 1265 remove_host: 1266 pm_runtime_put_noidle(&pdev->dev); 1267 tmio_mmc_host_remove(_host); 1268 return ret; 1269 } 1270 EXPORT_SYMBOL_GPL(tmio_mmc_host_probe); 1271 1272 void tmio_mmc_host_remove(struct tmio_mmc_host *host) 1273 { 1274 struct platform_device *pdev = host->pdev; 1275 struct mmc_host *mmc = host->mmc; 1276 1277 pm_runtime_get_sync(&pdev->dev); 1278 1279 if (host->pdata->flags & TMIO_MMC_SDIO_IRQ) 1280 sd_ctrl_write16(host, CTL_TRANSACTION_CTL, 0x0000); 1281 1282 dev_pm_qos_hide_latency_limit(&pdev->dev); 1283 1284 mmc_remove_host(mmc); 1285 cancel_work_sync(&host->done); 1286 cancel_delayed_work_sync(&host->delayed_reset_work); 1287 tmio_mmc_release_dma(host); 1288 1289 pm_runtime_dont_use_autosuspend(&pdev->dev); 1290 if (host->native_hotplug) 1291 pm_runtime_put_noidle(&pdev->dev); 1292 pm_runtime_put_sync(&pdev->dev); 1293 pm_runtime_disable(&pdev->dev); 1294 } 1295 EXPORT_SYMBOL_GPL(tmio_mmc_host_remove); 1296 1297 #ifdef CONFIG_PM 1298 static int tmio_mmc_clk_enable(struct tmio_mmc_host *host) 1299 { 1300 if (!host->clk_enable) 1301 return -ENOTSUPP; 1302 1303 return host->clk_enable(host); 1304 } 1305 1306 static void tmio_mmc_clk_disable(struct tmio_mmc_host *host) 1307 { 1308 if (host->clk_disable) 1309 host->clk_disable(host); 1310 } 1311 1312 int tmio_mmc_host_runtime_suspend(struct device *dev) 1313 { 1314 struct tmio_mmc_host *host = dev_get_drvdata(dev); 1315 1316 tmio_mmc_disable_mmc_irqs(host, TMIO_MASK_ALL); 1317 1318 if (host->clk_cache) 1319 host->set_clock(host, 0); 1320 1321 tmio_mmc_clk_disable(host); 1322 1323 return 0; 1324 } 1325 EXPORT_SYMBOL_GPL(tmio_mmc_host_runtime_suspend); 1326 1327 static bool tmio_mmc_can_retune(struct tmio_mmc_host *host) 1328 { 1329 return host->tap_num && mmc_can_retune(host->mmc); 1330 } 1331 1332 int tmio_mmc_host_runtime_resume(struct device *dev) 1333 { 1334 struct tmio_mmc_host *host = dev_get_drvdata(dev); 1335 1336 if (!host->runtime_synced) { 1337 host->runtime_synced = true; 1338 return 0; 1339 } 1340 1341 tmio_mmc_clk_enable(host); 1342 tmio_mmc_hw_reset(host->mmc); 1343 1344 if (host->clk_cache) 1345 host->set_clock(host, host->clk_cache); 1346 1347 if (host->native_hotplug) 1348 tmio_mmc_enable_mmc_irqs(host, 1349 TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT); 1350 1351 tmio_mmc_enable_dma(host, true); 1352 1353 if (tmio_mmc_can_retune(host) && host->select_tuning(host)) 1354 dev_warn(&host->pdev->dev, "Tuning selection failed\n"); 1355 1356 return 0; 1357 } 1358 EXPORT_SYMBOL_GPL(tmio_mmc_host_runtime_resume); 1359 #endif 1360 1361 MODULE_LICENSE("GPL v2"); 1362