1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright (C) 2010 Marvell International Ltd. 4 * Zhangfei Gao <zhangfei.gao@marvell.com> 5 * Kevin Wang <dwang4@marvell.com> 6 * Mingwei Wang <mwwang@marvell.com> 7 * Philip Rakity <prakity@marvell.com> 8 * Mark Brown <markb@marvell.com> 9 */ 10 #include <linux/err.h> 11 #include <linux/init.h> 12 #include <linux/platform_device.h> 13 #include <linux/clk.h> 14 #include <linux/io.h> 15 #include <linux/mmc/card.h> 16 #include <linux/mmc/host.h> 17 #include <linux/platform_data/pxa_sdhci.h> 18 #include <linux/slab.h> 19 #include <linux/delay.h> 20 #include <linux/module.h> 21 #include <linux/of.h> 22 #include <linux/of_device.h> 23 #include <linux/pm.h> 24 #include <linux/pm_runtime.h> 25 #include <linux/mbus.h> 26 27 #include "sdhci.h" 28 #include "sdhci-pltfm.h" 29 30 #define PXAV3_RPM_DELAY_MS 50 31 32 #define SD_CLOCK_BURST_SIZE_SETUP 0x10A 33 #define SDCLK_SEL 0x100 34 #define SDCLK_DELAY_SHIFT 9 35 #define SDCLK_DELAY_MASK 0x1f 36 37 #define SD_CFG_FIFO_PARAM 0x100 38 #define SDCFG_GEN_PAD_CLK_ON (1<<6) 39 #define SDCFG_GEN_PAD_CLK_CNT_MASK 0xFF 40 #define SDCFG_GEN_PAD_CLK_CNT_SHIFT 24 41 42 #define SD_SPI_MODE 0x108 43 #define SD_CE_ATA_1 0x10C 44 45 #define SD_CE_ATA_2 0x10E 46 #define SDCE_MISC_INT (1<<2) 47 #define SDCE_MISC_INT_EN (1<<1) 48 49 struct sdhci_pxa { 50 struct clk *clk_core; 51 struct clk *clk_io; 52 u8 power_mode; 53 void __iomem *sdio3_conf_reg; 54 }; 55 56 /* 57 * These registers are relative to the second register region, for the 58 * MBus bridge. 59 */ 60 #define SDHCI_WINDOW_CTRL(i) (0x80 + ((i) << 3)) 61 #define SDHCI_WINDOW_BASE(i) (0x84 + ((i) << 3)) 62 #define SDHCI_MAX_WIN_NUM 8 63 64 /* 65 * Fields below belong to SDIO3 Configuration Register (third register 66 * region for the Armada 38x flavor) 67 */ 68 69 #define SDIO3_CONF_CLK_INV BIT(0) 70 #define SDIO3_CONF_SD_FB_CLK BIT(2) 71 72 static int mv_conf_mbus_windows(struct platform_device *pdev, 73 const struct mbus_dram_target_info *dram) 74 { 75 int i; 76 void __iomem *regs; 77 struct resource *res; 78 79 if (!dram) { 80 dev_err(&pdev->dev, "no mbus dram info\n"); 81 return -EINVAL; 82 } 83 84 res = platform_get_resource(pdev, IORESOURCE_MEM, 1); 85 if (!res) { 86 dev_err(&pdev->dev, "cannot get mbus registers\n"); 87 return -EINVAL; 88 } 89 90 regs = ioremap(res->start, resource_size(res)); 91 if (!regs) { 92 dev_err(&pdev->dev, "cannot map mbus registers\n"); 93 return -ENOMEM; 94 } 95 96 for (i = 0; i < SDHCI_MAX_WIN_NUM; i++) { 97 writel(0, regs + SDHCI_WINDOW_CTRL(i)); 98 writel(0, regs + SDHCI_WINDOW_BASE(i)); 99 } 100 101 for (i = 0; i < dram->num_cs; i++) { 102 const struct mbus_dram_window *cs = dram->cs + i; 103 104 /* Write size, attributes and target id to control register */ 105 writel(((cs->size - 1) & 0xffff0000) | 106 (cs->mbus_attr << 8) | 107 (dram->mbus_dram_target_id << 4) | 1, 108 regs + SDHCI_WINDOW_CTRL(i)); 109 /* Write base address to base register */ 110 writel(cs->base, regs + SDHCI_WINDOW_BASE(i)); 111 } 112 113 iounmap(regs); 114 115 return 0; 116 } 117 118 static int armada_38x_quirks(struct platform_device *pdev, 119 struct sdhci_host *host) 120 { 121 struct device_node *np = pdev->dev.of_node; 122 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 123 struct sdhci_pxa *pxa = sdhci_pltfm_priv(pltfm_host); 124 struct resource *res; 125 126 host->quirks &= ~SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN; 127 host->quirks |= SDHCI_QUIRK_MISSING_CAPS; 128 129 host->caps = sdhci_readl(host, SDHCI_CAPABILITIES); 130 host->caps1 = sdhci_readl(host, SDHCI_CAPABILITIES_1); 131 132 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, 133 "conf-sdio3"); 134 if (res) { 135 pxa->sdio3_conf_reg = devm_ioremap_resource(&pdev->dev, res); 136 if (IS_ERR(pxa->sdio3_conf_reg)) 137 return PTR_ERR(pxa->sdio3_conf_reg); 138 } else { 139 /* 140 * According to erratum 'FE-2946959' both SDR50 and DDR50 141 * modes require specific clock adjustments in SDIO3 142 * Configuration register, if the adjustment is not done, 143 * remove them from the capabilities. 144 */ 145 host->caps1 &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50); 146 147 dev_warn(&pdev->dev, "conf-sdio3 register not found: disabling SDR50 and DDR50 modes.\nConsider updating your dtb\n"); 148 } 149 150 /* 151 * According to erratum 'ERR-7878951' Armada 38x SDHCI 152 * controller has different capabilities than the ones shown 153 * in its registers 154 */ 155 if (of_property_read_bool(np, "no-1-8-v")) { 156 host->caps &= ~SDHCI_CAN_VDD_180; 157 host->mmc->caps &= ~MMC_CAP_1_8V_DDR; 158 } else { 159 host->caps &= ~SDHCI_CAN_VDD_330; 160 } 161 host->caps1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_USE_SDR50_TUNING); 162 163 return 0; 164 } 165 166 static void pxav3_reset(struct sdhci_host *host, u8 mask) 167 { 168 struct platform_device *pdev = to_platform_device(mmc_dev(host->mmc)); 169 struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; 170 171 sdhci_reset(host, mask); 172 173 if (mask == SDHCI_RESET_ALL) { 174 /* 175 * tune timing of read data/command when crc error happen 176 * no performance impact 177 */ 178 if (pdata && 0 != pdata->clk_delay_cycles) { 179 u16 tmp; 180 181 tmp = readw(host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP); 182 tmp |= (pdata->clk_delay_cycles & SDCLK_DELAY_MASK) 183 << SDCLK_DELAY_SHIFT; 184 tmp |= SDCLK_SEL; 185 writew(tmp, host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP); 186 } 187 } 188 } 189 190 #define MAX_WAIT_COUNT 5 191 static void pxav3_gen_init_74_clocks(struct sdhci_host *host, u8 power_mode) 192 { 193 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 194 struct sdhci_pxa *pxa = sdhci_pltfm_priv(pltfm_host); 195 u16 tmp; 196 int count; 197 198 if (pxa->power_mode == MMC_POWER_UP 199 && power_mode == MMC_POWER_ON) { 200 201 dev_dbg(mmc_dev(host->mmc), 202 "%s: slot->power_mode = %d," 203 "ios->power_mode = %d\n", 204 __func__, 205 pxa->power_mode, 206 power_mode); 207 208 /* set we want notice of when 74 clocks are sent */ 209 tmp = readw(host->ioaddr + SD_CE_ATA_2); 210 tmp |= SDCE_MISC_INT_EN; 211 writew(tmp, host->ioaddr + SD_CE_ATA_2); 212 213 /* start sending the 74 clocks */ 214 tmp = readw(host->ioaddr + SD_CFG_FIFO_PARAM); 215 tmp |= SDCFG_GEN_PAD_CLK_ON; 216 writew(tmp, host->ioaddr + SD_CFG_FIFO_PARAM); 217 218 /* slowest speed is about 100KHz or 10usec per clock */ 219 udelay(740); 220 count = 0; 221 222 while (count++ < MAX_WAIT_COUNT) { 223 if ((readw(host->ioaddr + SD_CE_ATA_2) 224 & SDCE_MISC_INT) == 0) 225 break; 226 udelay(10); 227 } 228 229 if (count == MAX_WAIT_COUNT) 230 dev_warn(mmc_dev(host->mmc), "74 clock interrupt not cleared\n"); 231 232 /* clear the interrupt bit if posted */ 233 tmp = readw(host->ioaddr + SD_CE_ATA_2); 234 tmp |= SDCE_MISC_INT; 235 writew(tmp, host->ioaddr + SD_CE_ATA_2); 236 } 237 pxa->power_mode = power_mode; 238 } 239 240 static void pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs) 241 { 242 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 243 struct sdhci_pxa *pxa = sdhci_pltfm_priv(pltfm_host); 244 u16 ctrl_2; 245 246 /* 247 * Set V18_EN -- UHS modes do not work without this. 248 * does not change signaling voltage 249 */ 250 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); 251 252 /* Select Bus Speed Mode for host */ 253 ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; 254 switch (uhs) { 255 case MMC_TIMING_UHS_SDR12: 256 ctrl_2 |= SDHCI_CTRL_UHS_SDR12; 257 break; 258 case MMC_TIMING_UHS_SDR25: 259 ctrl_2 |= SDHCI_CTRL_UHS_SDR25; 260 break; 261 case MMC_TIMING_UHS_SDR50: 262 ctrl_2 |= SDHCI_CTRL_UHS_SDR50 | SDHCI_CTRL_VDD_180; 263 break; 264 case MMC_TIMING_UHS_SDR104: 265 ctrl_2 |= SDHCI_CTRL_UHS_SDR104 | SDHCI_CTRL_VDD_180; 266 break; 267 case MMC_TIMING_MMC_DDR52: 268 case MMC_TIMING_UHS_DDR50: 269 ctrl_2 |= SDHCI_CTRL_UHS_DDR50 | SDHCI_CTRL_VDD_180; 270 break; 271 } 272 273 /* 274 * Update SDIO3 Configuration register according to erratum 275 * FE-2946959 276 */ 277 if (pxa->sdio3_conf_reg) { 278 u8 reg_val = readb(pxa->sdio3_conf_reg); 279 280 if (uhs == MMC_TIMING_UHS_SDR50 || 281 uhs == MMC_TIMING_UHS_DDR50) { 282 reg_val &= ~SDIO3_CONF_CLK_INV; 283 reg_val |= SDIO3_CONF_SD_FB_CLK; 284 } else if (uhs == MMC_TIMING_MMC_HS) { 285 reg_val &= ~SDIO3_CONF_CLK_INV; 286 reg_val &= ~SDIO3_CONF_SD_FB_CLK; 287 } else { 288 reg_val |= SDIO3_CONF_CLK_INV; 289 reg_val &= ~SDIO3_CONF_SD_FB_CLK; 290 } 291 writeb(reg_val, pxa->sdio3_conf_reg); 292 } 293 294 sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); 295 dev_dbg(mmc_dev(host->mmc), 296 "%s uhs = %d, ctrl_2 = %04X\n", 297 __func__, uhs, ctrl_2); 298 } 299 300 static void pxav3_set_power(struct sdhci_host *host, unsigned char mode, 301 unsigned short vdd) 302 { 303 struct mmc_host *mmc = host->mmc; 304 u8 pwr = host->pwr; 305 306 sdhci_set_power_noreg(host, mode, vdd); 307 308 if (host->pwr == pwr) 309 return; 310 311 if (host->pwr == 0) 312 vdd = 0; 313 314 if (!IS_ERR(mmc->supply.vmmc)) 315 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd); 316 } 317 318 static const struct sdhci_ops pxav3_sdhci_ops = { 319 .set_clock = sdhci_set_clock, 320 .set_power = pxav3_set_power, 321 .platform_send_init_74_clocks = pxav3_gen_init_74_clocks, 322 .get_max_clock = sdhci_pltfm_clk_get_max_clock, 323 .set_bus_width = sdhci_set_bus_width, 324 .reset = pxav3_reset, 325 .set_uhs_signaling = pxav3_set_uhs_signaling, 326 }; 327 328 static const struct sdhci_pltfm_data sdhci_pxav3_pdata = { 329 .quirks = SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK 330 | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC 331 | SDHCI_QUIRK_32BIT_ADMA_SIZE 332 | SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN, 333 .ops = &pxav3_sdhci_ops, 334 }; 335 336 #ifdef CONFIG_OF 337 static const struct of_device_id sdhci_pxav3_of_match[] = { 338 { 339 .compatible = "mrvl,pxav3-mmc", 340 }, 341 { 342 .compatible = "marvell,armada-380-sdhci", 343 }, 344 {}, 345 }; 346 MODULE_DEVICE_TABLE(of, sdhci_pxav3_of_match); 347 348 static struct sdhci_pxa_platdata *pxav3_get_mmc_pdata(struct device *dev) 349 { 350 struct sdhci_pxa_platdata *pdata; 351 struct device_node *np = dev->of_node; 352 u32 clk_delay_cycles; 353 354 pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); 355 if (!pdata) 356 return NULL; 357 358 if (!of_property_read_u32(np, "mrvl,clk-delay-cycles", 359 &clk_delay_cycles)) 360 pdata->clk_delay_cycles = clk_delay_cycles; 361 362 return pdata; 363 } 364 #else 365 static inline struct sdhci_pxa_platdata *pxav3_get_mmc_pdata(struct device *dev) 366 { 367 return NULL; 368 } 369 #endif 370 371 static int sdhci_pxav3_probe(struct platform_device *pdev) 372 { 373 struct sdhci_pltfm_host *pltfm_host; 374 struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; 375 struct device *dev = &pdev->dev; 376 struct device_node *np = pdev->dev.of_node; 377 struct sdhci_host *host = NULL; 378 struct sdhci_pxa *pxa = NULL; 379 const struct of_device_id *match; 380 int ret; 381 382 host = sdhci_pltfm_init(pdev, &sdhci_pxav3_pdata, sizeof(*pxa)); 383 if (IS_ERR(host)) 384 return PTR_ERR(host); 385 386 pltfm_host = sdhci_priv(host); 387 pxa = sdhci_pltfm_priv(pltfm_host); 388 389 pxa->clk_io = devm_clk_get(dev, "io"); 390 if (IS_ERR(pxa->clk_io)) 391 pxa->clk_io = devm_clk_get(dev, NULL); 392 if (IS_ERR(pxa->clk_io)) { 393 dev_err(dev, "failed to get io clock\n"); 394 ret = PTR_ERR(pxa->clk_io); 395 goto err_clk_get; 396 } 397 pltfm_host->clk = pxa->clk_io; 398 clk_prepare_enable(pxa->clk_io); 399 400 pxa->clk_core = devm_clk_get(dev, "core"); 401 if (!IS_ERR(pxa->clk_core)) 402 clk_prepare_enable(pxa->clk_core); 403 404 /* enable 1/8V DDR capable */ 405 host->mmc->caps |= MMC_CAP_1_8V_DDR; 406 407 if (of_device_is_compatible(np, "marvell,armada-380-sdhci")) { 408 ret = armada_38x_quirks(pdev, host); 409 if (ret < 0) 410 goto err_mbus_win; 411 ret = mv_conf_mbus_windows(pdev, mv_mbus_dram_info()); 412 if (ret < 0) 413 goto err_mbus_win; 414 } 415 416 match = of_match_device(of_match_ptr(sdhci_pxav3_of_match), &pdev->dev); 417 if (match) { 418 ret = mmc_of_parse(host->mmc); 419 if (ret) 420 goto err_of_parse; 421 sdhci_get_of_property(pdev); 422 pdata = pxav3_get_mmc_pdata(dev); 423 pdev->dev.platform_data = pdata; 424 } else if (pdata) { 425 /* on-chip device */ 426 if (pdata->flags & PXA_FLAG_CARD_PERMANENT) 427 host->mmc->caps |= MMC_CAP_NONREMOVABLE; 428 429 /* If slot design supports 8 bit data, indicate this to MMC. */ 430 if (pdata->flags & PXA_FLAG_SD_8_BIT_CAPABLE_SLOT) 431 host->mmc->caps |= MMC_CAP_8_BIT_DATA; 432 433 if (pdata->quirks) 434 host->quirks |= pdata->quirks; 435 if (pdata->quirks2) 436 host->quirks2 |= pdata->quirks2; 437 if (pdata->host_caps) 438 host->mmc->caps |= pdata->host_caps; 439 if (pdata->host_caps2) 440 host->mmc->caps2 |= pdata->host_caps2; 441 if (pdata->pm_caps) 442 host->mmc->pm_caps |= pdata->pm_caps; 443 } 444 445 pm_runtime_get_noresume(&pdev->dev); 446 pm_runtime_set_active(&pdev->dev); 447 pm_runtime_set_autosuspend_delay(&pdev->dev, PXAV3_RPM_DELAY_MS); 448 pm_runtime_use_autosuspend(&pdev->dev); 449 pm_runtime_enable(&pdev->dev); 450 pm_suspend_ignore_children(&pdev->dev, 1); 451 452 ret = sdhci_add_host(host); 453 if (ret) 454 goto err_add_host; 455 456 if (host->mmc->pm_caps & MMC_PM_WAKE_SDIO_IRQ) 457 device_init_wakeup(&pdev->dev, 1); 458 459 pm_runtime_put_autosuspend(&pdev->dev); 460 461 return 0; 462 463 err_add_host: 464 pm_runtime_disable(&pdev->dev); 465 pm_runtime_put_noidle(&pdev->dev); 466 err_of_parse: 467 err_mbus_win: 468 clk_disable_unprepare(pxa->clk_io); 469 clk_disable_unprepare(pxa->clk_core); 470 err_clk_get: 471 sdhci_pltfm_free(pdev); 472 return ret; 473 } 474 475 static int sdhci_pxav3_remove(struct platform_device *pdev) 476 { 477 struct sdhci_host *host = platform_get_drvdata(pdev); 478 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 479 struct sdhci_pxa *pxa = sdhci_pltfm_priv(pltfm_host); 480 481 pm_runtime_get_sync(&pdev->dev); 482 pm_runtime_disable(&pdev->dev); 483 pm_runtime_put_noidle(&pdev->dev); 484 485 sdhci_remove_host(host, 1); 486 487 clk_disable_unprepare(pxa->clk_io); 488 clk_disable_unprepare(pxa->clk_core); 489 490 sdhci_pltfm_free(pdev); 491 492 return 0; 493 } 494 495 #ifdef CONFIG_PM_SLEEP 496 static int sdhci_pxav3_suspend(struct device *dev) 497 { 498 int ret; 499 struct sdhci_host *host = dev_get_drvdata(dev); 500 501 pm_runtime_get_sync(dev); 502 if (host->tuning_mode != SDHCI_TUNING_MODE_3) 503 mmc_retune_needed(host->mmc); 504 ret = sdhci_suspend_host(host); 505 pm_runtime_mark_last_busy(dev); 506 pm_runtime_put_autosuspend(dev); 507 508 return ret; 509 } 510 511 static int sdhci_pxav3_resume(struct device *dev) 512 { 513 int ret; 514 struct sdhci_host *host = dev_get_drvdata(dev); 515 516 pm_runtime_get_sync(dev); 517 ret = sdhci_resume_host(host); 518 pm_runtime_mark_last_busy(dev); 519 pm_runtime_put_autosuspend(dev); 520 521 return ret; 522 } 523 #endif 524 525 #ifdef CONFIG_PM 526 static int sdhci_pxav3_runtime_suspend(struct device *dev) 527 { 528 struct sdhci_host *host = dev_get_drvdata(dev); 529 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 530 struct sdhci_pxa *pxa = sdhci_pltfm_priv(pltfm_host); 531 int ret; 532 533 ret = sdhci_runtime_suspend_host(host); 534 if (ret) 535 return ret; 536 537 if (host->tuning_mode != SDHCI_TUNING_MODE_3) 538 mmc_retune_needed(host->mmc); 539 540 clk_disable_unprepare(pxa->clk_io); 541 if (!IS_ERR(pxa->clk_core)) 542 clk_disable_unprepare(pxa->clk_core); 543 544 return 0; 545 } 546 547 static int sdhci_pxav3_runtime_resume(struct device *dev) 548 { 549 struct sdhci_host *host = dev_get_drvdata(dev); 550 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 551 struct sdhci_pxa *pxa = sdhci_pltfm_priv(pltfm_host); 552 553 clk_prepare_enable(pxa->clk_io); 554 if (!IS_ERR(pxa->clk_core)) 555 clk_prepare_enable(pxa->clk_core); 556 557 return sdhci_runtime_resume_host(host, 0); 558 } 559 #endif 560 561 static const struct dev_pm_ops sdhci_pxav3_pmops = { 562 SET_SYSTEM_SLEEP_PM_OPS(sdhci_pxav3_suspend, sdhci_pxav3_resume) 563 SET_RUNTIME_PM_OPS(sdhci_pxav3_runtime_suspend, 564 sdhci_pxav3_runtime_resume, NULL) 565 }; 566 567 static struct platform_driver sdhci_pxav3_driver = { 568 .driver = { 569 .name = "sdhci-pxav3", 570 .probe_type = PROBE_PREFER_ASYNCHRONOUS, 571 .of_match_table = of_match_ptr(sdhci_pxav3_of_match), 572 .pm = &sdhci_pxav3_pmops, 573 }, 574 .probe = sdhci_pxav3_probe, 575 .remove = sdhci_pxav3_remove, 576 }; 577 578 module_platform_driver(sdhci_pxav3_driver); 579 580 MODULE_DESCRIPTION("SDHCI driver for pxav3"); 581 MODULE_AUTHOR("Marvell International Ltd."); 582 MODULE_LICENSE("GPL v2"); 583 584