1 /* 2 * drivers/mmc/host/sdhci-msm.c - Qualcomm SDHCI Platform driver 3 * 4 * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved. 5 * 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License version 2 and 8 * only version 2 as published by the Free Software Foundation. 9 * 10 * This program is distributed in the hope that it will be useful, 11 * but WITHOUT ANY WARRANTY; without even the implied warranty of 12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 13 * GNU General Public License for more details. 14 * 15 */ 16 17 #include <linux/module.h> 18 #include <linux/of_device.h> 19 #include <linux/delay.h> 20 #include <linux/mmc/mmc.h> 21 #include <linux/pm_runtime.h> 22 #include <linux/slab.h> 23 #include <linux/iopoll.h> 24 25 #include "sdhci-pltfm.h" 26 27 #define CORE_MCI_VERSION 0x50 28 #define CORE_VERSION_MAJOR_SHIFT 28 29 #define CORE_VERSION_MAJOR_MASK (0xf << CORE_VERSION_MAJOR_SHIFT) 30 #define CORE_VERSION_MINOR_MASK 0xff 31 32 #define CORE_HC_MODE 0x78 33 #define HC_MODE_EN 0x1 34 #define CORE_POWER 0x0 35 #define CORE_SW_RST BIT(7) 36 #define FF_CLK_SW_RST_DIS BIT(13) 37 38 #define CORE_PWRCTL_STATUS 0xdc 39 #define CORE_PWRCTL_MASK 0xe0 40 #define CORE_PWRCTL_CLEAR 0xe4 41 #define CORE_PWRCTL_CTL 0xe8 42 #define CORE_PWRCTL_BUS_OFF BIT(0) 43 #define CORE_PWRCTL_BUS_ON BIT(1) 44 #define CORE_PWRCTL_IO_LOW BIT(2) 45 #define CORE_PWRCTL_IO_HIGH BIT(3) 46 #define CORE_PWRCTL_BUS_SUCCESS BIT(0) 47 #define CORE_PWRCTL_IO_SUCCESS BIT(2) 48 #define REQ_BUS_OFF BIT(0) 49 #define REQ_BUS_ON BIT(1) 50 #define REQ_IO_LOW BIT(2) 51 #define REQ_IO_HIGH BIT(3) 52 #define INT_MASK 0xf 53 #define MAX_PHASES 16 54 #define CORE_DLL_LOCK BIT(7) 55 #define CORE_DDR_DLL_LOCK BIT(11) 56 #define CORE_DLL_EN BIT(16) 57 #define CORE_CDR_EN BIT(17) 58 #define CORE_CK_OUT_EN BIT(18) 59 #define CORE_CDR_EXT_EN BIT(19) 60 #define CORE_DLL_PDN BIT(29) 61 #define CORE_DLL_RST BIT(30) 62 #define CORE_DLL_CONFIG 0x100 63 #define CORE_CMD_DAT_TRACK_SEL BIT(0) 64 #define CORE_DLL_STATUS 0x108 65 66 #define CORE_DLL_CONFIG_2 0x1b4 67 #define CORE_DDR_CAL_EN BIT(0) 68 #define CORE_FLL_CYCLE_CNT BIT(18) 69 #define CORE_DLL_CLOCK_DISABLE BIT(21) 70 71 #define CORE_VENDOR_SPEC 0x10c 72 #define CORE_VENDOR_SPEC_POR_VAL 0xa1c 73 #define CORE_CLK_PWRSAVE BIT(1) 74 #define CORE_HC_MCLK_SEL_DFLT (2 << 8) 75 #define CORE_HC_MCLK_SEL_HS400 (3 << 8) 76 #define CORE_HC_MCLK_SEL_MASK (3 << 8) 77 #define CORE_HC_SELECT_IN_EN BIT(18) 78 #define CORE_HC_SELECT_IN_HS400 (6 << 19) 79 #define CORE_HC_SELECT_IN_MASK (7 << 19) 80 81 #define CORE_CSR_CDC_CTLR_CFG0 0x130 82 #define CORE_SW_TRIG_FULL_CALIB BIT(16) 83 #define CORE_HW_AUTOCAL_ENA BIT(17) 84 85 #define CORE_CSR_CDC_CTLR_CFG1 0x134 86 #define CORE_CSR_CDC_CAL_TIMER_CFG0 0x138 87 #define CORE_TIMER_ENA BIT(16) 88 89 #define CORE_CSR_CDC_CAL_TIMER_CFG1 0x13C 90 #define CORE_CSR_CDC_REFCOUNT_CFG 0x140 91 #define CORE_CSR_CDC_COARSE_CAL_CFG 0x144 92 #define CORE_CDC_OFFSET_CFG 0x14C 93 #define CORE_CSR_CDC_DELAY_CFG 0x150 94 #define CORE_CDC_SLAVE_DDA_CFG 0x160 95 #define CORE_CSR_CDC_STATUS0 0x164 96 #define CORE_CALIBRATION_DONE BIT(0) 97 98 #define CORE_CDC_ERROR_CODE_MASK 0x7000000 99 100 #define CORE_CSR_CDC_GEN_CFG 0x178 101 #define CORE_CDC_SWITCH_BYPASS_OFF BIT(0) 102 #define CORE_CDC_SWITCH_RC_EN BIT(1) 103 104 #define CORE_DDR_200_CFG 0x184 105 #define CORE_CDC_T4_DLY_SEL BIT(0) 106 #define CORE_CMDIN_RCLK_EN BIT(1) 107 #define CORE_START_CDC_TRAFFIC BIT(6) 108 #define CORE_VENDOR_SPEC3 0x1b0 109 #define CORE_PWRSAVE_DLL BIT(3) 110 111 #define CORE_DDR_CONFIG 0x1b8 112 #define DDR_CONFIG_POR_VAL 0x80040853 113 114 #define CORE_VENDOR_SPEC_CAPABILITIES0 0x11c 115 116 #define INVALID_TUNING_PHASE -1 117 #define SDHCI_MSM_MIN_CLOCK 400000 118 #define CORE_FREQ_100MHZ (100 * 1000 * 1000) 119 120 #define CDR_SELEXT_SHIFT 20 121 #define CDR_SELEXT_MASK (0xf << CDR_SELEXT_SHIFT) 122 #define CMUX_SHIFT_PHASE_SHIFT 24 123 #define CMUX_SHIFT_PHASE_MASK (7 << CMUX_SHIFT_PHASE_SHIFT) 124 125 #define MSM_MMC_AUTOSUSPEND_DELAY_MS 50 126 struct sdhci_msm_host { 127 struct platform_device *pdev; 128 void __iomem *core_mem; /* MSM SDCC mapped address */ 129 int pwr_irq; /* power irq */ 130 struct clk *clk; /* main SD/MMC bus clock */ 131 struct clk *pclk; /* SDHC peripheral bus clock */ 132 struct clk *bus_clk; /* SDHC bus voter clock */ 133 struct clk *xo_clk; /* TCXO clk needed for FLL feature of cm_dll*/ 134 unsigned long clk_rate; 135 struct mmc_host *mmc; 136 bool use_14lpp_dll_reset; 137 bool tuning_done; 138 bool calibration_done; 139 u8 saved_tuning_phase; 140 bool use_cdclp533; 141 }; 142 143 static unsigned int msm_get_clock_rate_for_bus_mode(struct sdhci_host *host, 144 unsigned int clock) 145 { 146 struct mmc_ios ios = host->mmc->ios; 147 /* 148 * The SDHC requires internal clock frequency to be double the 149 * actual clock that will be set for DDR mode. The controller 150 * uses the faster clock(100/400MHz) for some of its parts and 151 * send the actual required clock (50/200MHz) to the card. 152 */ 153 if (ios.timing == MMC_TIMING_UHS_DDR50 || 154 ios.timing == MMC_TIMING_MMC_DDR52 || 155 ios.timing == MMC_TIMING_MMC_HS400 || 156 host->flags & SDHCI_HS400_TUNING) 157 clock *= 2; 158 return clock; 159 } 160 161 static void msm_set_clock_rate_for_bus_mode(struct sdhci_host *host, 162 unsigned int clock) 163 { 164 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 165 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 166 struct mmc_ios curr_ios = host->mmc->ios; 167 int rc; 168 169 clock = msm_get_clock_rate_for_bus_mode(host, clock); 170 rc = clk_set_rate(msm_host->clk, clock); 171 if (rc) { 172 pr_err("%s: Failed to set clock at rate %u at timing %d\n", 173 mmc_hostname(host->mmc), clock, 174 curr_ios.timing); 175 return; 176 } 177 msm_host->clk_rate = clock; 178 pr_debug("%s: Setting clock at rate %lu at timing %d\n", 179 mmc_hostname(host->mmc), clk_get_rate(msm_host->clk), 180 curr_ios.timing); 181 } 182 183 /* Platform specific tuning */ 184 static inline int msm_dll_poll_ck_out_en(struct sdhci_host *host, u8 poll) 185 { 186 u32 wait_cnt = 50; 187 u8 ck_out_en; 188 struct mmc_host *mmc = host->mmc; 189 190 /* Poll for CK_OUT_EN bit. max. poll time = 50us */ 191 ck_out_en = !!(readl_relaxed(host->ioaddr + CORE_DLL_CONFIG) & 192 CORE_CK_OUT_EN); 193 194 while (ck_out_en != poll) { 195 if (--wait_cnt == 0) { 196 dev_err(mmc_dev(mmc), "%s: CK_OUT_EN bit is not %d\n", 197 mmc_hostname(mmc), poll); 198 return -ETIMEDOUT; 199 } 200 udelay(1); 201 202 ck_out_en = !!(readl_relaxed(host->ioaddr + CORE_DLL_CONFIG) & 203 CORE_CK_OUT_EN); 204 } 205 206 return 0; 207 } 208 209 static int msm_config_cm_dll_phase(struct sdhci_host *host, u8 phase) 210 { 211 int rc; 212 static const u8 grey_coded_phase_table[] = { 213 0x0, 0x1, 0x3, 0x2, 0x6, 0x7, 0x5, 0x4, 214 0xc, 0xd, 0xf, 0xe, 0xa, 0xb, 0x9, 0x8 215 }; 216 unsigned long flags; 217 u32 config; 218 struct mmc_host *mmc = host->mmc; 219 220 if (phase > 0xf) 221 return -EINVAL; 222 223 spin_lock_irqsave(&host->lock, flags); 224 225 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 226 config &= ~(CORE_CDR_EN | CORE_CK_OUT_EN); 227 config |= (CORE_CDR_EXT_EN | CORE_DLL_EN); 228 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 229 230 /* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '0' */ 231 rc = msm_dll_poll_ck_out_en(host, 0); 232 if (rc) 233 goto err_out; 234 235 /* 236 * Write the selected DLL clock output phase (0 ... 15) 237 * to CDR_SELEXT bit field of DLL_CONFIG register. 238 */ 239 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 240 config &= ~CDR_SELEXT_MASK; 241 config |= grey_coded_phase_table[phase] << CDR_SELEXT_SHIFT; 242 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 243 244 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 245 config |= CORE_CK_OUT_EN; 246 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 247 248 /* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '1' */ 249 rc = msm_dll_poll_ck_out_en(host, 1); 250 if (rc) 251 goto err_out; 252 253 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 254 config |= CORE_CDR_EN; 255 config &= ~CORE_CDR_EXT_EN; 256 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 257 goto out; 258 259 err_out: 260 dev_err(mmc_dev(mmc), "%s: Failed to set DLL phase: %d\n", 261 mmc_hostname(mmc), phase); 262 out: 263 spin_unlock_irqrestore(&host->lock, flags); 264 return rc; 265 } 266 267 /* 268 * Find out the greatest range of consecuitive selected 269 * DLL clock output phases that can be used as sampling 270 * setting for SD3.0 UHS-I card read operation (in SDR104 271 * timing mode) or for eMMC4.5 card read operation (in 272 * HS400/HS200 timing mode). 273 * Select the 3/4 of the range and configure the DLL with the 274 * selected DLL clock output phase. 275 */ 276 277 static int msm_find_most_appropriate_phase(struct sdhci_host *host, 278 u8 *phase_table, u8 total_phases) 279 { 280 int ret; 281 u8 ranges[MAX_PHASES][MAX_PHASES] = { {0}, {0} }; 282 u8 phases_per_row[MAX_PHASES] = { 0 }; 283 int row_index = 0, col_index = 0, selected_row_index = 0, curr_max = 0; 284 int i, cnt, phase_0_raw_index = 0, phase_15_raw_index = 0; 285 bool phase_0_found = false, phase_15_found = false; 286 struct mmc_host *mmc = host->mmc; 287 288 if (!total_phases || (total_phases > MAX_PHASES)) { 289 dev_err(mmc_dev(mmc), "%s: Invalid argument: total_phases=%d\n", 290 mmc_hostname(mmc), total_phases); 291 return -EINVAL; 292 } 293 294 for (cnt = 0; cnt < total_phases; cnt++) { 295 ranges[row_index][col_index] = phase_table[cnt]; 296 phases_per_row[row_index] += 1; 297 col_index++; 298 299 if ((cnt + 1) == total_phases) { 300 continue; 301 /* check if next phase in phase_table is consecutive or not */ 302 } else if ((phase_table[cnt] + 1) != phase_table[cnt + 1]) { 303 row_index++; 304 col_index = 0; 305 } 306 } 307 308 if (row_index >= MAX_PHASES) 309 return -EINVAL; 310 311 /* Check if phase-0 is present in first valid window? */ 312 if (!ranges[0][0]) { 313 phase_0_found = true; 314 phase_0_raw_index = 0; 315 /* Check if cycle exist between 2 valid windows */ 316 for (cnt = 1; cnt <= row_index; cnt++) { 317 if (phases_per_row[cnt]) { 318 for (i = 0; i < phases_per_row[cnt]; i++) { 319 if (ranges[cnt][i] == 15) { 320 phase_15_found = true; 321 phase_15_raw_index = cnt; 322 break; 323 } 324 } 325 } 326 } 327 } 328 329 /* If 2 valid windows form cycle then merge them as single window */ 330 if (phase_0_found && phase_15_found) { 331 /* number of phases in raw where phase 0 is present */ 332 u8 phases_0 = phases_per_row[phase_0_raw_index]; 333 /* number of phases in raw where phase 15 is present */ 334 u8 phases_15 = phases_per_row[phase_15_raw_index]; 335 336 if (phases_0 + phases_15 >= MAX_PHASES) 337 /* 338 * If there are more than 1 phase windows then total 339 * number of phases in both the windows should not be 340 * more than or equal to MAX_PHASES. 341 */ 342 return -EINVAL; 343 344 /* Merge 2 cyclic windows */ 345 i = phases_15; 346 for (cnt = 0; cnt < phases_0; cnt++) { 347 ranges[phase_15_raw_index][i] = 348 ranges[phase_0_raw_index][cnt]; 349 if (++i >= MAX_PHASES) 350 break; 351 } 352 353 phases_per_row[phase_0_raw_index] = 0; 354 phases_per_row[phase_15_raw_index] = phases_15 + phases_0; 355 } 356 357 for (cnt = 0; cnt <= row_index; cnt++) { 358 if (phases_per_row[cnt] > curr_max) { 359 curr_max = phases_per_row[cnt]; 360 selected_row_index = cnt; 361 } 362 } 363 364 i = (curr_max * 3) / 4; 365 if (i) 366 i--; 367 368 ret = ranges[selected_row_index][i]; 369 370 if (ret >= MAX_PHASES) { 371 ret = -EINVAL; 372 dev_err(mmc_dev(mmc), "%s: Invalid phase selected=%d\n", 373 mmc_hostname(mmc), ret); 374 } 375 376 return ret; 377 } 378 379 static inline void msm_cm_dll_set_freq(struct sdhci_host *host) 380 { 381 u32 mclk_freq = 0, config; 382 383 /* Program the MCLK value to MCLK_FREQ bit field */ 384 if (host->clock <= 112000000) 385 mclk_freq = 0; 386 else if (host->clock <= 125000000) 387 mclk_freq = 1; 388 else if (host->clock <= 137000000) 389 mclk_freq = 2; 390 else if (host->clock <= 150000000) 391 mclk_freq = 3; 392 else if (host->clock <= 162000000) 393 mclk_freq = 4; 394 else if (host->clock <= 175000000) 395 mclk_freq = 5; 396 else if (host->clock <= 187000000) 397 mclk_freq = 6; 398 else if (host->clock <= 200000000) 399 mclk_freq = 7; 400 401 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 402 config &= ~CMUX_SHIFT_PHASE_MASK; 403 config |= mclk_freq << CMUX_SHIFT_PHASE_SHIFT; 404 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 405 } 406 407 /* Initialize the DLL (Programmable Delay Line) */ 408 static int msm_init_cm_dll(struct sdhci_host *host) 409 { 410 struct mmc_host *mmc = host->mmc; 411 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 412 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 413 int wait_cnt = 50; 414 unsigned long flags; 415 u32 config; 416 417 spin_lock_irqsave(&host->lock, flags); 418 419 /* 420 * Make sure that clock is always enabled when DLL 421 * tuning is in progress. Keeping PWRSAVE ON may 422 * turn off the clock. 423 */ 424 config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC); 425 config &= ~CORE_CLK_PWRSAVE; 426 writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC); 427 428 if (msm_host->use_14lpp_dll_reset) { 429 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 430 config &= ~CORE_CK_OUT_EN; 431 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 432 433 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG_2); 434 config |= CORE_DLL_CLOCK_DISABLE; 435 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG_2); 436 } 437 438 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 439 config |= CORE_DLL_RST; 440 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 441 442 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 443 config |= CORE_DLL_PDN; 444 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 445 msm_cm_dll_set_freq(host); 446 447 if (msm_host->use_14lpp_dll_reset && 448 !IS_ERR_OR_NULL(msm_host->xo_clk)) { 449 u32 mclk_freq = 0; 450 451 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG_2); 452 config &= CORE_FLL_CYCLE_CNT; 453 if (config) 454 mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 8), 455 clk_get_rate(msm_host->xo_clk)); 456 else 457 mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 4), 458 clk_get_rate(msm_host->xo_clk)); 459 460 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG_2); 461 config &= ~(0xFF << 10); 462 config |= mclk_freq << 10; 463 464 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG_2); 465 /* wait for 5us before enabling DLL clock */ 466 udelay(5); 467 } 468 469 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 470 config &= ~CORE_DLL_RST; 471 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 472 473 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 474 config &= ~CORE_DLL_PDN; 475 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 476 477 if (msm_host->use_14lpp_dll_reset) { 478 msm_cm_dll_set_freq(host); 479 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG_2); 480 config &= ~CORE_DLL_CLOCK_DISABLE; 481 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG_2); 482 } 483 484 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 485 config |= CORE_DLL_EN; 486 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 487 488 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 489 config |= CORE_CK_OUT_EN; 490 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 491 492 /* Wait until DLL_LOCK bit of DLL_STATUS register becomes '1' */ 493 while (!(readl_relaxed(host->ioaddr + CORE_DLL_STATUS) & 494 CORE_DLL_LOCK)) { 495 /* max. wait for 50us sec for LOCK bit to be set */ 496 if (--wait_cnt == 0) { 497 dev_err(mmc_dev(mmc), "%s: DLL failed to LOCK\n", 498 mmc_hostname(mmc)); 499 spin_unlock_irqrestore(&host->lock, flags); 500 return -ETIMEDOUT; 501 } 502 udelay(1); 503 } 504 505 spin_unlock_irqrestore(&host->lock, flags); 506 return 0; 507 } 508 509 static void msm_hc_select_default(struct sdhci_host *host) 510 { 511 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 512 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 513 u32 config; 514 515 if (!msm_host->use_cdclp533) { 516 config = readl_relaxed(host->ioaddr + 517 CORE_VENDOR_SPEC3); 518 config &= ~CORE_PWRSAVE_DLL; 519 writel_relaxed(config, host->ioaddr + 520 CORE_VENDOR_SPEC3); 521 } 522 523 config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC); 524 config &= ~CORE_HC_MCLK_SEL_MASK; 525 config |= CORE_HC_MCLK_SEL_DFLT; 526 writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC); 527 528 /* 529 * Disable HC_SELECT_IN to be able to use the UHS mode select 530 * configuration from Host Control2 register for all other 531 * modes. 532 * Write 0 to HC_SELECT_IN and HC_SELECT_IN_EN field 533 * in VENDOR_SPEC_FUNC 534 */ 535 config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC); 536 config &= ~CORE_HC_SELECT_IN_EN; 537 config &= ~CORE_HC_SELECT_IN_MASK; 538 writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC); 539 540 /* 541 * Make sure above writes impacting free running MCLK are completed 542 * before changing the clk_rate at GCC. 543 */ 544 wmb(); 545 } 546 547 static void msm_hc_select_hs400(struct sdhci_host *host) 548 { 549 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 550 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 551 struct mmc_ios ios = host->mmc->ios; 552 u32 config, dll_lock; 553 int rc; 554 555 /* Select the divided clock (free running MCLK/2) */ 556 config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC); 557 config &= ~CORE_HC_MCLK_SEL_MASK; 558 config |= CORE_HC_MCLK_SEL_HS400; 559 560 writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC); 561 /* 562 * Select HS400 mode using the HC_SELECT_IN from VENDOR SPEC 563 * register 564 */ 565 if ((msm_host->tuning_done || ios.enhanced_strobe) && 566 !msm_host->calibration_done) { 567 config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC); 568 config |= CORE_HC_SELECT_IN_HS400; 569 config |= CORE_HC_SELECT_IN_EN; 570 writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC); 571 } 572 if (!msm_host->clk_rate && !msm_host->use_cdclp533) { 573 /* 574 * Poll on DLL_LOCK or DDR_DLL_LOCK bits in 575 * CORE_DLL_STATUS to be set. This should get set 576 * within 15 us at 200 MHz. 577 */ 578 rc = readl_relaxed_poll_timeout(host->ioaddr + 579 CORE_DLL_STATUS, 580 dll_lock, 581 (dll_lock & 582 (CORE_DLL_LOCK | 583 CORE_DDR_DLL_LOCK)), 10, 584 1000); 585 if (rc == -ETIMEDOUT) 586 pr_err("%s: Unable to get DLL_LOCK/DDR_DLL_LOCK, dll_status: 0x%08x\n", 587 mmc_hostname(host->mmc), dll_lock); 588 } 589 /* 590 * Make sure above writes impacting free running MCLK are completed 591 * before changing the clk_rate at GCC. 592 */ 593 wmb(); 594 } 595 596 /* 597 * sdhci_msm_hc_select_mode :- In general all timing modes are 598 * controlled via UHS mode select in Host Control2 register. 599 * eMMC specific HS200/HS400 doesn't have their respective modes 600 * defined here, hence we use these values. 601 * 602 * HS200 - SDR104 (Since they both are equivalent in functionality) 603 * HS400 - This involves multiple configurations 604 * Initially SDR104 - when tuning is required as HS200 605 * Then when switching to DDR @ 400MHz (HS400) we use 606 * the vendor specific HC_SELECT_IN to control the mode. 607 * 608 * In addition to controlling the modes we also need to select the 609 * correct input clock for DLL depending on the mode. 610 * 611 * HS400 - divided clock (free running MCLK/2) 612 * All other modes - default (free running MCLK) 613 */ 614 static void sdhci_msm_hc_select_mode(struct sdhci_host *host) 615 { 616 struct mmc_ios ios = host->mmc->ios; 617 618 if (ios.timing == MMC_TIMING_MMC_HS400 || 619 host->flags & SDHCI_HS400_TUNING) 620 msm_hc_select_hs400(host); 621 else 622 msm_hc_select_default(host); 623 } 624 625 static int sdhci_msm_cdclp533_calibration(struct sdhci_host *host) 626 { 627 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 628 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 629 u32 config, calib_done; 630 int ret; 631 632 pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__); 633 634 /* 635 * Retuning in HS400 (DDR mode) will fail, just reset the 636 * tuning block and restore the saved tuning phase. 637 */ 638 ret = msm_init_cm_dll(host); 639 if (ret) 640 goto out; 641 642 /* Set the selected phase in delay line hw block */ 643 ret = msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase); 644 if (ret) 645 goto out; 646 647 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 648 config |= CORE_CMD_DAT_TRACK_SEL; 649 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 650 651 config = readl_relaxed(host->ioaddr + CORE_DDR_200_CFG); 652 config &= ~CORE_CDC_T4_DLY_SEL; 653 writel_relaxed(config, host->ioaddr + CORE_DDR_200_CFG); 654 655 config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG); 656 config &= ~CORE_CDC_SWITCH_BYPASS_OFF; 657 writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG); 658 659 config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG); 660 config |= CORE_CDC_SWITCH_RC_EN; 661 writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG); 662 663 config = readl_relaxed(host->ioaddr + CORE_DDR_200_CFG); 664 config &= ~CORE_START_CDC_TRAFFIC; 665 writel_relaxed(config, host->ioaddr + CORE_DDR_200_CFG); 666 667 /* Perform CDC Register Initialization Sequence */ 668 669 writel_relaxed(0x11800EC, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); 670 writel_relaxed(0x3011111, host->ioaddr + CORE_CSR_CDC_CTLR_CFG1); 671 writel_relaxed(0x1201000, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0); 672 writel_relaxed(0x4, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG1); 673 writel_relaxed(0xCB732020, host->ioaddr + CORE_CSR_CDC_REFCOUNT_CFG); 674 writel_relaxed(0xB19, host->ioaddr + CORE_CSR_CDC_COARSE_CAL_CFG); 675 writel_relaxed(0x4E2, host->ioaddr + CORE_CSR_CDC_DELAY_CFG); 676 writel_relaxed(0x0, host->ioaddr + CORE_CDC_OFFSET_CFG); 677 writel_relaxed(0x16334, host->ioaddr + CORE_CDC_SLAVE_DDA_CFG); 678 679 /* CDC HW Calibration */ 680 681 config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); 682 config |= CORE_SW_TRIG_FULL_CALIB; 683 writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); 684 685 config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); 686 config &= ~CORE_SW_TRIG_FULL_CALIB; 687 writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); 688 689 config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); 690 config |= CORE_HW_AUTOCAL_ENA; 691 writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); 692 693 config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0); 694 config |= CORE_TIMER_ENA; 695 writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0); 696 697 ret = readl_relaxed_poll_timeout(host->ioaddr + CORE_CSR_CDC_STATUS0, 698 calib_done, 699 (calib_done & CORE_CALIBRATION_DONE), 700 1, 50); 701 702 if (ret == -ETIMEDOUT) { 703 pr_err("%s: %s: CDC calibration was not completed\n", 704 mmc_hostname(host->mmc), __func__); 705 goto out; 706 } 707 708 ret = readl_relaxed(host->ioaddr + CORE_CSR_CDC_STATUS0) 709 & CORE_CDC_ERROR_CODE_MASK; 710 if (ret) { 711 pr_err("%s: %s: CDC error code %d\n", 712 mmc_hostname(host->mmc), __func__, ret); 713 ret = -EINVAL; 714 goto out; 715 } 716 717 config = readl_relaxed(host->ioaddr + CORE_DDR_200_CFG); 718 config |= CORE_START_CDC_TRAFFIC; 719 writel_relaxed(config, host->ioaddr + CORE_DDR_200_CFG); 720 out: 721 pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc), 722 __func__, ret); 723 return ret; 724 } 725 726 static int sdhci_msm_cm_dll_sdc4_calibration(struct sdhci_host *host) 727 { 728 struct mmc_host *mmc = host->mmc; 729 u32 dll_status, config; 730 int ret; 731 732 pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__); 733 734 /* 735 * Currently the CORE_DDR_CONFIG register defaults to desired 736 * configuration on reset. Currently reprogramming the power on 737 * reset (POR) value in case it might have been modified by 738 * bootloaders. In the future, if this changes, then the desired 739 * values will need to be programmed appropriately. 740 */ 741 writel_relaxed(DDR_CONFIG_POR_VAL, host->ioaddr + CORE_DDR_CONFIG); 742 743 if (mmc->ios.enhanced_strobe) { 744 config = readl_relaxed(host->ioaddr + CORE_DDR_200_CFG); 745 config |= CORE_CMDIN_RCLK_EN; 746 writel_relaxed(config, host->ioaddr + CORE_DDR_200_CFG); 747 } 748 749 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG_2); 750 config |= CORE_DDR_CAL_EN; 751 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG_2); 752 753 ret = readl_relaxed_poll_timeout(host->ioaddr + CORE_DLL_STATUS, 754 dll_status, 755 (dll_status & CORE_DDR_DLL_LOCK), 756 10, 1000); 757 758 if (ret == -ETIMEDOUT) { 759 pr_err("%s: %s: CM_DLL_SDC4 calibration was not completed\n", 760 mmc_hostname(host->mmc), __func__); 761 goto out; 762 } 763 764 config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC3); 765 config |= CORE_PWRSAVE_DLL; 766 writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC3); 767 768 /* 769 * Drain writebuffer to ensure above DLL calibration 770 * and PWRSAVE DLL is enabled. 771 */ 772 wmb(); 773 out: 774 pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc), 775 __func__, ret); 776 return ret; 777 } 778 779 static int sdhci_msm_hs400_dll_calibration(struct sdhci_host *host) 780 { 781 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 782 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 783 struct mmc_host *mmc = host->mmc; 784 int ret; 785 u32 config; 786 787 pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__); 788 789 /* 790 * Retuning in HS400 (DDR mode) will fail, just reset the 791 * tuning block and restore the saved tuning phase. 792 */ 793 ret = msm_init_cm_dll(host); 794 if (ret) 795 goto out; 796 797 if (!mmc->ios.enhanced_strobe) { 798 /* Set the selected phase in delay line hw block */ 799 ret = msm_config_cm_dll_phase(host, 800 msm_host->saved_tuning_phase); 801 if (ret) 802 goto out; 803 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 804 config |= CORE_CMD_DAT_TRACK_SEL; 805 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 806 } 807 808 if (msm_host->use_cdclp533) 809 ret = sdhci_msm_cdclp533_calibration(host); 810 else 811 ret = sdhci_msm_cm_dll_sdc4_calibration(host); 812 out: 813 pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc), 814 __func__, ret); 815 return ret; 816 } 817 818 static int sdhci_msm_execute_tuning(struct mmc_host *mmc, u32 opcode) 819 { 820 struct sdhci_host *host = mmc_priv(mmc); 821 int tuning_seq_cnt = 3; 822 u8 phase, tuned_phases[16], tuned_phase_cnt = 0; 823 int rc; 824 struct mmc_ios ios = host->mmc->ios; 825 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 826 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 827 828 /* 829 * Tuning is required for SDR104, HS200 and HS400 cards and 830 * if clock frequency is greater than 100MHz in these modes. 831 */ 832 if (host->clock <= CORE_FREQ_100MHZ || 833 !(ios.timing == MMC_TIMING_MMC_HS400 || 834 ios.timing == MMC_TIMING_MMC_HS200 || 835 ios.timing == MMC_TIMING_UHS_SDR104)) 836 return 0; 837 838 /* 839 * For HS400 tuning in HS200 timing requires: 840 * - select MCLK/2 in VENDOR_SPEC 841 * - program MCLK to 400MHz (or nearest supported) in GCC 842 */ 843 if (host->flags & SDHCI_HS400_TUNING) { 844 sdhci_msm_hc_select_mode(host); 845 msm_set_clock_rate_for_bus_mode(host, ios.clock); 846 host->flags &= ~SDHCI_HS400_TUNING; 847 } 848 849 retry: 850 /* First of all reset the tuning block */ 851 rc = msm_init_cm_dll(host); 852 if (rc) 853 return rc; 854 855 phase = 0; 856 do { 857 /* Set the phase in delay line hw block */ 858 rc = msm_config_cm_dll_phase(host, phase); 859 if (rc) 860 return rc; 861 862 msm_host->saved_tuning_phase = phase; 863 rc = mmc_send_tuning(mmc, opcode, NULL); 864 if (!rc) { 865 /* Tuning is successful at this tuning point */ 866 tuned_phases[tuned_phase_cnt++] = phase; 867 dev_dbg(mmc_dev(mmc), "%s: Found good phase = %d\n", 868 mmc_hostname(mmc), phase); 869 } 870 } while (++phase < ARRAY_SIZE(tuned_phases)); 871 872 if (tuned_phase_cnt) { 873 rc = msm_find_most_appropriate_phase(host, tuned_phases, 874 tuned_phase_cnt); 875 if (rc < 0) 876 return rc; 877 else 878 phase = rc; 879 880 /* 881 * Finally set the selected phase in delay 882 * line hw block. 883 */ 884 rc = msm_config_cm_dll_phase(host, phase); 885 if (rc) 886 return rc; 887 dev_dbg(mmc_dev(mmc), "%s: Setting the tuning phase to %d\n", 888 mmc_hostname(mmc), phase); 889 } else { 890 if (--tuning_seq_cnt) 891 goto retry; 892 /* Tuning failed */ 893 dev_dbg(mmc_dev(mmc), "%s: No tuning point found\n", 894 mmc_hostname(mmc)); 895 rc = -EIO; 896 } 897 898 if (!rc) 899 msm_host->tuning_done = true; 900 return rc; 901 } 902 903 /* 904 * sdhci_msm_hs400 - Calibrate the DLL for HS400 bus speed mode operation. 905 * This needs to be done for both tuning and enhanced_strobe mode. 906 * DLL operation is only needed for clock > 100MHz. For clock <= 100MHz 907 * fixed feedback clock is used. 908 */ 909 static void sdhci_msm_hs400(struct sdhci_host *host, struct mmc_ios *ios) 910 { 911 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 912 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 913 int ret; 914 915 if (host->clock > CORE_FREQ_100MHZ && 916 (msm_host->tuning_done || ios->enhanced_strobe) && 917 !msm_host->calibration_done) { 918 ret = sdhci_msm_hs400_dll_calibration(host); 919 if (!ret) 920 msm_host->calibration_done = true; 921 else 922 pr_err("%s: Failed to calibrate DLL for hs400 mode (%d)\n", 923 mmc_hostname(host->mmc), ret); 924 } 925 } 926 927 static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host, 928 unsigned int uhs) 929 { 930 struct mmc_host *mmc = host->mmc; 931 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 932 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 933 u16 ctrl_2; 934 u32 config; 935 936 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); 937 /* Select Bus Speed Mode for host */ 938 ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; 939 switch (uhs) { 940 case MMC_TIMING_UHS_SDR12: 941 ctrl_2 |= SDHCI_CTRL_UHS_SDR12; 942 break; 943 case MMC_TIMING_UHS_SDR25: 944 ctrl_2 |= SDHCI_CTRL_UHS_SDR25; 945 break; 946 case MMC_TIMING_UHS_SDR50: 947 ctrl_2 |= SDHCI_CTRL_UHS_SDR50; 948 break; 949 case MMC_TIMING_MMC_HS400: 950 case MMC_TIMING_MMC_HS200: 951 case MMC_TIMING_UHS_SDR104: 952 ctrl_2 |= SDHCI_CTRL_UHS_SDR104; 953 break; 954 case MMC_TIMING_UHS_DDR50: 955 case MMC_TIMING_MMC_DDR52: 956 ctrl_2 |= SDHCI_CTRL_UHS_DDR50; 957 break; 958 } 959 960 /* 961 * When clock frequency is less than 100MHz, the feedback clock must be 962 * provided and DLL must not be used so that tuning can be skipped. To 963 * provide feedback clock, the mode selection can be any value less 964 * than 3'b011 in bits [2:0] of HOST CONTROL2 register. 965 */ 966 if (host->clock <= CORE_FREQ_100MHZ) { 967 if (uhs == MMC_TIMING_MMC_HS400 || 968 uhs == MMC_TIMING_MMC_HS200 || 969 uhs == MMC_TIMING_UHS_SDR104) 970 ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; 971 /* 972 * DLL is not required for clock <= 100MHz 973 * Thus, make sure DLL it is disabled when not required 974 */ 975 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 976 config |= CORE_DLL_RST; 977 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 978 979 config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); 980 config |= CORE_DLL_PDN; 981 writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); 982 983 /* 984 * The DLL needs to be restored and CDCLP533 recalibrated 985 * when the clock frequency is set back to 400MHz. 986 */ 987 msm_host->calibration_done = false; 988 } 989 990 dev_dbg(mmc_dev(mmc), "%s: clock=%u uhs=%u ctrl_2=0x%x\n", 991 mmc_hostname(host->mmc), host->clock, uhs, ctrl_2); 992 sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); 993 994 if (mmc->ios.timing == MMC_TIMING_MMC_HS400) 995 sdhci_msm_hs400(host, &mmc->ios); 996 } 997 998 static void sdhci_msm_voltage_switch(struct sdhci_host *host) 999 { 1000 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1001 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 1002 u32 irq_status, irq_ack = 0; 1003 1004 irq_status = readl_relaxed(msm_host->core_mem + CORE_PWRCTL_STATUS); 1005 irq_status &= INT_MASK; 1006 1007 writel_relaxed(irq_status, msm_host->core_mem + CORE_PWRCTL_CLEAR); 1008 1009 if (irq_status & (CORE_PWRCTL_BUS_ON | CORE_PWRCTL_BUS_OFF)) 1010 irq_ack |= CORE_PWRCTL_BUS_SUCCESS; 1011 if (irq_status & (CORE_PWRCTL_IO_LOW | CORE_PWRCTL_IO_HIGH)) 1012 irq_ack |= CORE_PWRCTL_IO_SUCCESS; 1013 1014 /* 1015 * The driver has to acknowledge the interrupt, switch voltages and 1016 * report back if it succeded or not to this register. The voltage 1017 * switches are handled by the sdhci core, so just report success. 1018 */ 1019 writel_relaxed(irq_ack, msm_host->core_mem + CORE_PWRCTL_CTL); 1020 } 1021 1022 static irqreturn_t sdhci_msm_pwr_irq(int irq, void *data) 1023 { 1024 struct sdhci_host *host = (struct sdhci_host *)data; 1025 1026 sdhci_msm_voltage_switch(host); 1027 1028 return IRQ_HANDLED; 1029 } 1030 1031 static unsigned int sdhci_msm_get_max_clock(struct sdhci_host *host) 1032 { 1033 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1034 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 1035 1036 return clk_round_rate(msm_host->clk, ULONG_MAX); 1037 } 1038 1039 static unsigned int sdhci_msm_get_min_clock(struct sdhci_host *host) 1040 { 1041 return SDHCI_MSM_MIN_CLOCK; 1042 } 1043 1044 /** 1045 * __sdhci_msm_set_clock - sdhci_msm clock control. 1046 * 1047 * Description: 1048 * MSM controller does not use internal divider and 1049 * instead directly control the GCC clock as per 1050 * HW recommendation. 1051 **/ 1052 static void __sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock) 1053 { 1054 u16 clk; 1055 /* 1056 * Keep actual_clock as zero - 1057 * - since there is no divider used so no need of having actual_clock. 1058 * - MSM controller uses SDCLK for data timeout calculation. If 1059 * actual_clock is zero, host->clock is taken for calculation. 1060 */ 1061 host->mmc->actual_clock = 0; 1062 1063 sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL); 1064 1065 if (clock == 0) 1066 return; 1067 1068 /* 1069 * MSM controller do not use clock divider. 1070 * Thus read SDHCI_CLOCK_CONTROL and only enable 1071 * clock with no divider value programmed. 1072 */ 1073 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL); 1074 sdhci_enable_clk(host, clk); 1075 } 1076 1077 /* sdhci_msm_set_clock - Called with (host->lock) spinlock held. */ 1078 static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock) 1079 { 1080 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1081 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 1082 1083 if (!clock) { 1084 msm_host->clk_rate = clock; 1085 goto out; 1086 } 1087 1088 sdhci_msm_hc_select_mode(host); 1089 1090 msm_set_clock_rate_for_bus_mode(host, clock); 1091 out: 1092 __sdhci_msm_set_clock(host, clock); 1093 } 1094 1095 static const struct of_device_id sdhci_msm_dt_match[] = { 1096 { .compatible = "qcom,sdhci-msm-v4" }, 1097 {}, 1098 }; 1099 1100 MODULE_DEVICE_TABLE(of, sdhci_msm_dt_match); 1101 1102 static const struct sdhci_ops sdhci_msm_ops = { 1103 .reset = sdhci_reset, 1104 .set_clock = sdhci_msm_set_clock, 1105 .get_min_clock = sdhci_msm_get_min_clock, 1106 .get_max_clock = sdhci_msm_get_max_clock, 1107 .set_bus_width = sdhci_set_bus_width, 1108 .set_uhs_signaling = sdhci_msm_set_uhs_signaling, 1109 .voltage_switch = sdhci_msm_voltage_switch, 1110 }; 1111 1112 static const struct sdhci_pltfm_data sdhci_msm_pdata = { 1113 .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION | 1114 SDHCI_QUIRK_NO_CARD_NO_RESET | 1115 SDHCI_QUIRK_SINGLE_POWER_WRITE | 1116 SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN, 1117 .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN, 1118 .ops = &sdhci_msm_ops, 1119 }; 1120 1121 static int sdhci_msm_probe(struct platform_device *pdev) 1122 { 1123 struct sdhci_host *host; 1124 struct sdhci_pltfm_host *pltfm_host; 1125 struct sdhci_msm_host *msm_host; 1126 struct resource *core_memres; 1127 int ret; 1128 u16 host_version, core_minor; 1129 u32 core_version, config; 1130 u8 core_major; 1131 1132 host = sdhci_pltfm_init(pdev, &sdhci_msm_pdata, sizeof(*msm_host)); 1133 if (IS_ERR(host)) 1134 return PTR_ERR(host); 1135 1136 host->sdma_boundary = 0; 1137 pltfm_host = sdhci_priv(host); 1138 msm_host = sdhci_pltfm_priv(pltfm_host); 1139 msm_host->mmc = host->mmc; 1140 msm_host->pdev = pdev; 1141 1142 ret = mmc_of_parse(host->mmc); 1143 if (ret) 1144 goto pltfm_free; 1145 1146 sdhci_get_of_property(pdev); 1147 1148 msm_host->saved_tuning_phase = INVALID_TUNING_PHASE; 1149 1150 /* Setup SDCC bus voter clock. */ 1151 msm_host->bus_clk = devm_clk_get(&pdev->dev, "bus"); 1152 if (!IS_ERR(msm_host->bus_clk)) { 1153 /* Vote for max. clk rate for max. performance */ 1154 ret = clk_set_rate(msm_host->bus_clk, INT_MAX); 1155 if (ret) 1156 goto pltfm_free; 1157 ret = clk_prepare_enable(msm_host->bus_clk); 1158 if (ret) 1159 goto pltfm_free; 1160 } 1161 1162 /* Setup main peripheral bus clock */ 1163 msm_host->pclk = devm_clk_get(&pdev->dev, "iface"); 1164 if (IS_ERR(msm_host->pclk)) { 1165 ret = PTR_ERR(msm_host->pclk); 1166 dev_err(&pdev->dev, "Peripheral clk setup failed (%d)\n", ret); 1167 goto bus_clk_disable; 1168 } 1169 1170 ret = clk_prepare_enable(msm_host->pclk); 1171 if (ret) 1172 goto bus_clk_disable; 1173 1174 /* Setup SDC MMC clock */ 1175 msm_host->clk = devm_clk_get(&pdev->dev, "core"); 1176 if (IS_ERR(msm_host->clk)) { 1177 ret = PTR_ERR(msm_host->clk); 1178 dev_err(&pdev->dev, "SDC MMC clk setup failed (%d)\n", ret); 1179 goto pclk_disable; 1180 } 1181 1182 /* 1183 * xo clock is needed for FLL feature of cm_dll. 1184 * In case if xo clock is not mentioned in DT, warn and proceed. 1185 */ 1186 msm_host->xo_clk = devm_clk_get(&pdev->dev, "xo"); 1187 if (IS_ERR(msm_host->xo_clk)) { 1188 ret = PTR_ERR(msm_host->xo_clk); 1189 dev_warn(&pdev->dev, "TCXO clk not present (%d)\n", ret); 1190 } 1191 1192 /* Vote for maximum clock rate for maximum performance */ 1193 ret = clk_set_rate(msm_host->clk, INT_MAX); 1194 if (ret) 1195 dev_warn(&pdev->dev, "core clock boost failed\n"); 1196 1197 ret = clk_prepare_enable(msm_host->clk); 1198 if (ret) 1199 goto pclk_disable; 1200 1201 core_memres = platform_get_resource(pdev, IORESOURCE_MEM, 1); 1202 msm_host->core_mem = devm_ioremap_resource(&pdev->dev, core_memres); 1203 1204 if (IS_ERR(msm_host->core_mem)) { 1205 dev_err(&pdev->dev, "Failed to remap registers\n"); 1206 ret = PTR_ERR(msm_host->core_mem); 1207 goto clk_disable; 1208 } 1209 1210 /* Reset the vendor spec register to power on reset state */ 1211 writel_relaxed(CORE_VENDOR_SPEC_POR_VAL, 1212 host->ioaddr + CORE_VENDOR_SPEC); 1213 1214 /* Set HC_MODE_EN bit in HC_MODE register */ 1215 writel_relaxed(HC_MODE_EN, (msm_host->core_mem + CORE_HC_MODE)); 1216 1217 config = readl_relaxed(msm_host->core_mem + CORE_HC_MODE); 1218 config |= FF_CLK_SW_RST_DIS; 1219 writel_relaxed(config, msm_host->core_mem + CORE_HC_MODE); 1220 1221 host_version = readw_relaxed((host->ioaddr + SDHCI_HOST_VERSION)); 1222 dev_dbg(&pdev->dev, "Host Version: 0x%x Vendor Version 0x%x\n", 1223 host_version, ((host_version & SDHCI_VENDOR_VER_MASK) >> 1224 SDHCI_VENDOR_VER_SHIFT)); 1225 1226 core_version = readl_relaxed(msm_host->core_mem + CORE_MCI_VERSION); 1227 core_major = (core_version & CORE_VERSION_MAJOR_MASK) >> 1228 CORE_VERSION_MAJOR_SHIFT; 1229 core_minor = core_version & CORE_VERSION_MINOR_MASK; 1230 dev_dbg(&pdev->dev, "MCI Version: 0x%08x, major: 0x%04x, minor: 0x%02x\n", 1231 core_version, core_major, core_minor); 1232 1233 if (core_major == 1 && core_minor >= 0x42) 1234 msm_host->use_14lpp_dll_reset = true; 1235 1236 /* 1237 * SDCC 5 controller with major version 1, minor version 0x34 and later 1238 * with HS 400 mode support will use CM DLL instead of CDC LP 533 DLL. 1239 */ 1240 if (core_major == 1 && core_minor < 0x34) 1241 msm_host->use_cdclp533 = true; 1242 1243 /* 1244 * Support for some capabilities is not advertised by newer 1245 * controller versions and must be explicitly enabled. 1246 */ 1247 if (core_major >= 1 && core_minor != 0x11 && core_minor != 0x12) { 1248 config = readl_relaxed(host->ioaddr + SDHCI_CAPABILITIES); 1249 config |= SDHCI_CAN_VDD_300 | SDHCI_CAN_DO_8BIT; 1250 writel_relaxed(config, host->ioaddr + 1251 CORE_VENDOR_SPEC_CAPABILITIES0); 1252 } 1253 1254 /* Setup IRQ for handling power/voltage tasks with PMIC */ 1255 msm_host->pwr_irq = platform_get_irq_byname(pdev, "pwr_irq"); 1256 if (msm_host->pwr_irq < 0) { 1257 dev_err(&pdev->dev, "Get pwr_irq failed (%d)\n", 1258 msm_host->pwr_irq); 1259 ret = msm_host->pwr_irq; 1260 goto clk_disable; 1261 } 1262 1263 ret = devm_request_threaded_irq(&pdev->dev, msm_host->pwr_irq, NULL, 1264 sdhci_msm_pwr_irq, IRQF_ONESHOT, 1265 dev_name(&pdev->dev), host); 1266 if (ret) { 1267 dev_err(&pdev->dev, "Request IRQ failed (%d)\n", ret); 1268 goto clk_disable; 1269 } 1270 1271 pm_runtime_get_noresume(&pdev->dev); 1272 pm_runtime_set_active(&pdev->dev); 1273 pm_runtime_enable(&pdev->dev); 1274 pm_runtime_set_autosuspend_delay(&pdev->dev, 1275 MSM_MMC_AUTOSUSPEND_DELAY_MS); 1276 pm_runtime_use_autosuspend(&pdev->dev); 1277 1278 host->mmc_host_ops.execute_tuning = sdhci_msm_execute_tuning; 1279 ret = sdhci_add_host(host); 1280 if (ret) 1281 goto pm_runtime_disable; 1282 1283 pm_runtime_mark_last_busy(&pdev->dev); 1284 pm_runtime_put_autosuspend(&pdev->dev); 1285 1286 return 0; 1287 1288 pm_runtime_disable: 1289 pm_runtime_disable(&pdev->dev); 1290 pm_runtime_set_suspended(&pdev->dev); 1291 pm_runtime_put_noidle(&pdev->dev); 1292 clk_disable: 1293 clk_disable_unprepare(msm_host->clk); 1294 pclk_disable: 1295 clk_disable_unprepare(msm_host->pclk); 1296 bus_clk_disable: 1297 if (!IS_ERR(msm_host->bus_clk)) 1298 clk_disable_unprepare(msm_host->bus_clk); 1299 pltfm_free: 1300 sdhci_pltfm_free(pdev); 1301 return ret; 1302 } 1303 1304 static int sdhci_msm_remove(struct platform_device *pdev) 1305 { 1306 struct sdhci_host *host = platform_get_drvdata(pdev); 1307 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1308 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 1309 int dead = (readl_relaxed(host->ioaddr + SDHCI_INT_STATUS) == 1310 0xffffffff); 1311 1312 sdhci_remove_host(host, dead); 1313 1314 pm_runtime_get_sync(&pdev->dev); 1315 pm_runtime_disable(&pdev->dev); 1316 pm_runtime_put_noidle(&pdev->dev); 1317 1318 clk_disable_unprepare(msm_host->clk); 1319 clk_disable_unprepare(msm_host->pclk); 1320 if (!IS_ERR(msm_host->bus_clk)) 1321 clk_disable_unprepare(msm_host->bus_clk); 1322 sdhci_pltfm_free(pdev); 1323 return 0; 1324 } 1325 1326 #ifdef CONFIG_PM 1327 static int sdhci_msm_runtime_suspend(struct device *dev) 1328 { 1329 struct sdhci_host *host = dev_get_drvdata(dev); 1330 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1331 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 1332 1333 clk_disable_unprepare(msm_host->clk); 1334 clk_disable_unprepare(msm_host->pclk); 1335 1336 return 0; 1337 } 1338 1339 static int sdhci_msm_runtime_resume(struct device *dev) 1340 { 1341 struct sdhci_host *host = dev_get_drvdata(dev); 1342 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1343 struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); 1344 int ret; 1345 1346 ret = clk_prepare_enable(msm_host->clk); 1347 if (ret) { 1348 dev_err(dev, "clk_enable failed for core_clk: %d\n", ret); 1349 return ret; 1350 } 1351 ret = clk_prepare_enable(msm_host->pclk); 1352 if (ret) { 1353 dev_err(dev, "clk_enable failed for iface_clk: %d\n", ret); 1354 clk_disable_unprepare(msm_host->clk); 1355 return ret; 1356 } 1357 1358 return 0; 1359 } 1360 #endif 1361 1362 static const struct dev_pm_ops sdhci_msm_pm_ops = { 1363 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, 1364 pm_runtime_force_resume) 1365 SET_RUNTIME_PM_OPS(sdhci_msm_runtime_suspend, 1366 sdhci_msm_runtime_resume, 1367 NULL) 1368 }; 1369 1370 static struct platform_driver sdhci_msm_driver = { 1371 .probe = sdhci_msm_probe, 1372 .remove = sdhci_msm_remove, 1373 .driver = { 1374 .name = "sdhci_msm", 1375 .of_match_table = sdhci_msm_dt_match, 1376 .pm = &sdhci_msm_pm_ops, 1377 }, 1378 }; 1379 1380 module_platform_driver(sdhci_msm_driver); 1381 1382 MODULE_DESCRIPTION("Qualcomm Secure Digital Host Controller Interface driver"); 1383 MODULE_LICENSE("GPL v2"); 1384