1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Freescale eSDHC i.MX controller driver for the platform bus. 4 * 5 * derived from the OF-version. 6 * 7 * Copyright (c) 2010 Pengutronix e.K. 8 * Author: Wolfram Sang <kernel@pengutronix.de> 9 */ 10 11 #include <linux/bitfield.h> 12 #include <linux/io.h> 13 #include <linux/iopoll.h> 14 #include <linux/delay.h> 15 #include <linux/err.h> 16 #include <linux/clk.h> 17 #include <linux/module.h> 18 #include <linux/slab.h> 19 #include <linux/pm_qos.h> 20 #include <linux/mmc/host.h> 21 #include <linux/mmc/mmc.h> 22 #include <linux/mmc/sdio.h> 23 #include <linux/mmc/slot-gpio.h> 24 #include <linux/of.h> 25 #include <linux/of_device.h> 26 #include <linux/pinctrl/consumer.h> 27 #include <linux/pm_runtime.h> 28 #include "sdhci-cqhci.h" 29 #include "sdhci-pltfm.h" 30 #include "sdhci-esdhc.h" 31 #include "cqhci.h" 32 33 #define ESDHC_SYS_CTRL_DTOCV_MASK 0x0f 34 #define ESDHC_CTRL_D3CD 0x08 35 #define ESDHC_BURST_LEN_EN_INCR (1 << 27) 36 /* VENDOR SPEC register */ 37 #define ESDHC_VENDOR_SPEC 0xc0 38 #define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1) 39 #define ESDHC_VENDOR_SPEC_VSELECT (1 << 1) 40 #define ESDHC_VENDOR_SPEC_FRC_SDCLK_ON (1 << 8) 41 #define ESDHC_DEBUG_SEL_AND_STATUS_REG 0xc2 42 #define ESDHC_DEBUG_SEL_REG 0xc3 43 #define ESDHC_DEBUG_SEL_MASK 0xf 44 #define ESDHC_DEBUG_SEL_CMD_STATE 1 45 #define ESDHC_DEBUG_SEL_DATA_STATE 2 46 #define ESDHC_DEBUG_SEL_TRANS_STATE 3 47 #define ESDHC_DEBUG_SEL_DMA_STATE 4 48 #define ESDHC_DEBUG_SEL_ADMA_STATE 5 49 #define ESDHC_DEBUG_SEL_FIFO_STATE 6 50 #define ESDHC_DEBUG_SEL_ASYNC_FIFO_STATE 7 51 #define ESDHC_WTMK_LVL 0x44 52 #define ESDHC_WTMK_DEFAULT_VAL 0x10401040 53 #define ESDHC_WTMK_LVL_RD_WML_MASK 0x000000FF 54 #define ESDHC_WTMK_LVL_RD_WML_SHIFT 0 55 #define ESDHC_WTMK_LVL_WR_WML_MASK 0x00FF0000 56 #define ESDHC_WTMK_LVL_WR_WML_SHIFT 16 57 #define ESDHC_WTMK_LVL_WML_VAL_DEF 64 58 #define ESDHC_WTMK_LVL_WML_VAL_MAX 128 59 #define ESDHC_MIX_CTRL 0x48 60 #define ESDHC_MIX_CTRL_DDREN (1 << 3) 61 #define ESDHC_MIX_CTRL_AC23EN (1 << 7) 62 #define ESDHC_MIX_CTRL_EXE_TUNE (1 << 22) 63 #define ESDHC_MIX_CTRL_SMPCLK_SEL (1 << 23) 64 #define ESDHC_MIX_CTRL_AUTO_TUNE_EN (1 << 24) 65 #define ESDHC_MIX_CTRL_FBCLK_SEL (1 << 25) 66 #define ESDHC_MIX_CTRL_HS400_EN (1 << 26) 67 #define ESDHC_MIX_CTRL_HS400_ES_EN (1 << 27) 68 /* Bits 3 and 6 are not SDHCI standard definitions */ 69 #define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7 70 /* Tuning bits */ 71 #define ESDHC_MIX_CTRL_TUNING_MASK 0x03c00000 72 73 /* dll control register */ 74 #define ESDHC_DLL_CTRL 0x60 75 #define ESDHC_DLL_OVERRIDE_VAL_SHIFT 9 76 #define ESDHC_DLL_OVERRIDE_EN_SHIFT 8 77 78 /* tune control register */ 79 #define ESDHC_TUNE_CTRL_STATUS 0x68 80 #define ESDHC_TUNE_CTRL_STEP 1 81 #define ESDHC_TUNE_CTRL_MIN 0 82 #define ESDHC_TUNE_CTRL_MAX ((1 << 7) - 1) 83 84 /* strobe dll register */ 85 #define ESDHC_STROBE_DLL_CTRL 0x70 86 #define ESDHC_STROBE_DLL_CTRL_ENABLE (1 << 0) 87 #define ESDHC_STROBE_DLL_CTRL_RESET (1 << 1) 88 #define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT 0x7 89 #define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT 3 90 #define ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT (4 << 20) 91 92 #define ESDHC_STROBE_DLL_STATUS 0x74 93 #define ESDHC_STROBE_DLL_STS_REF_LOCK (1 << 1) 94 #define ESDHC_STROBE_DLL_STS_SLV_LOCK 0x1 95 96 #define ESDHC_VEND_SPEC2 0xc8 97 #define ESDHC_VEND_SPEC2_EN_BUSY_IRQ (1 << 8) 98 #define ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN (1 << 4) 99 #define ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN (0 << 4) 100 #define ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN (2 << 4) 101 #define ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN (1 << 6) 102 #define ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK (7 << 4) 103 104 #define ESDHC_TUNING_CTRL 0xcc 105 #define ESDHC_STD_TUNING_EN (1 << 24) 106 /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */ 107 #define ESDHC_TUNING_START_TAP_DEFAULT 0x1 108 #define ESDHC_TUNING_START_TAP_MASK 0x7f 109 #define ESDHC_TUNING_CMD_CRC_CHECK_DISABLE (1 << 7) 110 #define ESDHC_TUNING_STEP_DEFAULT 0x1 111 #define ESDHC_TUNING_STEP_MASK 0x00070000 112 #define ESDHC_TUNING_STEP_SHIFT 16 113 114 /* pinctrl state */ 115 #define ESDHC_PINCTRL_STATE_100MHZ "state_100mhz" 116 #define ESDHC_PINCTRL_STATE_200MHZ "state_200mhz" 117 118 /* 119 * Our interpretation of the SDHCI_HOST_CONTROL register 120 */ 121 #define ESDHC_CTRL_4BITBUS (0x1 << 1) 122 #define ESDHC_CTRL_8BITBUS (0x2 << 1) 123 #define ESDHC_CTRL_BUSWIDTH_MASK (0x3 << 1) 124 #define USDHC_GET_BUSWIDTH(c) (c & ESDHC_CTRL_BUSWIDTH_MASK) 125 126 /* 127 * There is an INT DMA ERR mismatch between eSDHC and STD SDHC SPEC: 128 * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design, 129 * but bit28 is used as the INT DMA ERR in fsl eSDHC design. 130 * Define this macro DMA error INT for fsl eSDHC 131 */ 132 #define ESDHC_INT_VENDOR_SPEC_DMA_ERR (1 << 28) 133 134 /* the address offset of CQHCI */ 135 #define ESDHC_CQHCI_ADDR_OFFSET 0x100 136 137 /* 138 * The CMDTYPE of the CMD register (offset 0xE) should be set to 139 * "11" when the STOP CMD12 is issued on imx53 to abort one 140 * open ended multi-blk IO. Otherwise the TC INT wouldn't 141 * be generated. 142 * In exact block transfer, the controller doesn't complete the 143 * operations automatically as required at the end of the 144 * transfer and remains on hold if the abort command is not sent. 145 * As a result, the TC flag is not asserted and SW received timeout 146 * exception. Bit1 of Vendor Spec register is used to fix it. 147 */ 148 #define ESDHC_FLAG_MULTIBLK_NO_INT BIT(1) 149 /* 150 * The flag tells that the ESDHC controller is an USDHC block that is 151 * integrated on the i.MX6 series. 152 */ 153 #define ESDHC_FLAG_USDHC BIT(3) 154 /* The IP supports manual tuning process */ 155 #define ESDHC_FLAG_MAN_TUNING BIT(4) 156 /* The IP supports standard tuning process */ 157 #define ESDHC_FLAG_STD_TUNING BIT(5) 158 /* The IP has SDHCI_CAPABILITIES_1 register */ 159 #define ESDHC_FLAG_HAVE_CAP1 BIT(6) 160 /* 161 * The IP has erratum ERR004536 162 * uSDHC: ADMA Length Mismatch Error occurs if the AHB read access is slow, 163 * when reading data from the card 164 * This flag is also set for i.MX25 and i.MX35 in order to get 165 * SDHCI_QUIRK_BROKEN_ADMA, but for different reasons (ADMA capability bits). 166 */ 167 #define ESDHC_FLAG_ERR004536 BIT(7) 168 /* The IP supports HS200 mode */ 169 #define ESDHC_FLAG_HS200 BIT(8) 170 /* The IP supports HS400 mode */ 171 #define ESDHC_FLAG_HS400 BIT(9) 172 /* 173 * The IP has errata ERR010450 174 * uSDHC: Due to the I/O timing limit, for SDR mode, SD card clock can't 175 * exceed 150MHz, for DDR mode, SD card clock can't exceed 45MHz. 176 */ 177 #define ESDHC_FLAG_ERR010450 BIT(10) 178 /* The IP supports HS400ES mode */ 179 #define ESDHC_FLAG_HS400_ES BIT(11) 180 /* The IP has Host Controller Interface for Command Queuing */ 181 #define ESDHC_FLAG_CQHCI BIT(12) 182 /* need request pmqos during low power */ 183 #define ESDHC_FLAG_PMQOS BIT(13) 184 /* The IP state got lost in low power mode */ 185 #define ESDHC_FLAG_STATE_LOST_IN_LPMODE BIT(14) 186 /* The IP lost clock rate in PM_RUNTIME */ 187 #define ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME BIT(15) 188 /* 189 * The IP do not support the ACMD23 feature completely when use ADMA mode. 190 * In ADMA mode, it only use the 16 bit block count of the register 0x4 191 * (BLOCK_ATT) as the CMD23's argument for ACMD23 mode, which means it will 192 * ignore the upper 16 bit of the CMD23's argument. This will block the reliable 193 * write operation in RPMB, because RPMB reliable write need to set the bit31 194 * of the CMD23's argument. 195 * imx6qpdl/imx6sx/imx6sl/imx7d has this limitation only for ADMA mode, SDMA 196 * do not has this limitation. so when these SoC use ADMA mode, it need to 197 * disable the ACMD23 feature. 198 */ 199 #define ESDHC_FLAG_BROKEN_AUTO_CMD23 BIT(16) 200 201 /* ERR004536 is not applicable for the IP */ 202 #define ESDHC_FLAG_SKIP_ERR004536 BIT(17) 203 204 enum wp_types { 205 ESDHC_WP_NONE, /* no WP, neither controller nor gpio */ 206 ESDHC_WP_CONTROLLER, /* mmc controller internal WP */ 207 ESDHC_WP_GPIO, /* external gpio pin for WP */ 208 }; 209 210 enum cd_types { 211 ESDHC_CD_NONE, /* no CD, neither controller nor gpio */ 212 ESDHC_CD_CONTROLLER, /* mmc controller internal CD */ 213 ESDHC_CD_GPIO, /* external gpio pin for CD */ 214 ESDHC_CD_PERMANENT, /* no CD, card permanently wired to host */ 215 }; 216 217 /* 218 * struct esdhc_platform_data - platform data for esdhc on i.MX 219 * 220 * ESDHC_WP(CD)_CONTROLLER type is not available on i.MX25/35. 221 * 222 * @wp_type: type of write_protect method (see wp_types enum above) 223 * @cd_type: type of card_detect method (see cd_types enum above) 224 */ 225 226 struct esdhc_platform_data { 227 enum wp_types wp_type; 228 enum cd_types cd_type; 229 int max_bus_width; 230 unsigned int delay_line; 231 unsigned int tuning_step; /* The delay cell steps in tuning procedure */ 232 unsigned int tuning_start_tap; /* The start delay cell point in tuning procedure */ 233 unsigned int strobe_dll_delay_target; /* The delay cell for strobe pad (read clock) */ 234 }; 235 236 struct esdhc_soc_data { 237 u32 flags; 238 }; 239 240 static const struct esdhc_soc_data esdhc_imx25_data = { 241 .flags = ESDHC_FLAG_ERR004536, 242 }; 243 244 static const struct esdhc_soc_data esdhc_imx35_data = { 245 .flags = ESDHC_FLAG_ERR004536, 246 }; 247 248 static const struct esdhc_soc_data esdhc_imx51_data = { 249 .flags = 0, 250 }; 251 252 static const struct esdhc_soc_data esdhc_imx53_data = { 253 .flags = ESDHC_FLAG_MULTIBLK_NO_INT, 254 }; 255 256 static const struct esdhc_soc_data usdhc_imx6q_data = { 257 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING 258 | ESDHC_FLAG_BROKEN_AUTO_CMD23, 259 }; 260 261 static const struct esdhc_soc_data usdhc_imx6sl_data = { 262 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 263 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_ERR004536 264 | ESDHC_FLAG_HS200 265 | ESDHC_FLAG_BROKEN_AUTO_CMD23, 266 }; 267 268 static const struct esdhc_soc_data usdhc_imx6sll_data = { 269 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 270 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 271 | ESDHC_FLAG_HS400 272 | ESDHC_FLAG_STATE_LOST_IN_LPMODE, 273 }; 274 275 static const struct esdhc_soc_data usdhc_imx6sx_data = { 276 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 277 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 278 | ESDHC_FLAG_STATE_LOST_IN_LPMODE 279 | ESDHC_FLAG_BROKEN_AUTO_CMD23, 280 }; 281 282 static const struct esdhc_soc_data usdhc_imx6ull_data = { 283 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 284 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 285 | ESDHC_FLAG_ERR010450 286 | ESDHC_FLAG_STATE_LOST_IN_LPMODE, 287 }; 288 289 static const struct esdhc_soc_data usdhc_imx7d_data = { 290 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 291 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 292 | ESDHC_FLAG_HS400 293 | ESDHC_FLAG_STATE_LOST_IN_LPMODE 294 | ESDHC_FLAG_BROKEN_AUTO_CMD23, 295 }; 296 297 static struct esdhc_soc_data usdhc_s32g2_data = { 298 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING 299 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 300 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES 301 | ESDHC_FLAG_SKIP_ERR004536, 302 }; 303 304 static struct esdhc_soc_data usdhc_imx7ulp_data = { 305 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 306 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 307 | ESDHC_FLAG_PMQOS | ESDHC_FLAG_HS400 308 | ESDHC_FLAG_STATE_LOST_IN_LPMODE, 309 }; 310 static struct esdhc_soc_data usdhc_imxrt1050_data = { 311 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 312 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200, 313 }; 314 315 static struct esdhc_soc_data usdhc_imx8qxp_data = { 316 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 317 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 318 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES 319 | ESDHC_FLAG_STATE_LOST_IN_LPMODE 320 | ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME, 321 }; 322 323 static struct esdhc_soc_data usdhc_imx8mm_data = { 324 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 325 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 326 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES 327 | ESDHC_FLAG_STATE_LOST_IN_LPMODE, 328 }; 329 330 struct pltfm_imx_data { 331 u32 scratchpad; 332 struct pinctrl *pinctrl; 333 struct pinctrl_state *pins_100mhz; 334 struct pinctrl_state *pins_200mhz; 335 const struct esdhc_soc_data *socdata; 336 struct esdhc_platform_data boarddata; 337 struct clk *clk_ipg; 338 struct clk *clk_ahb; 339 struct clk *clk_per; 340 unsigned int actual_clock; 341 342 /* 343 * USDHC has one limition, require the SDIO device a different 344 * register setting. Driver has to recognize card type during 345 * the card init, but at this stage, mmc_host->card is not 346 * available. So involve this field to save the card type 347 * during card init through usdhc_init_card(). 348 */ 349 unsigned int init_card_type; 350 351 enum { 352 NO_CMD_PENDING, /* no multiblock command pending */ 353 MULTIBLK_IN_PROCESS, /* exact multiblock cmd in process */ 354 WAIT_FOR_INT, /* sent CMD12, waiting for response INT */ 355 } multiblock_status; 356 u32 is_ddr; 357 struct pm_qos_request pm_qos_req; 358 }; 359 360 static const struct of_device_id imx_esdhc_dt_ids[] = { 361 { .compatible = "fsl,imx25-esdhc", .data = &esdhc_imx25_data, }, 362 { .compatible = "fsl,imx35-esdhc", .data = &esdhc_imx35_data, }, 363 { .compatible = "fsl,imx51-esdhc", .data = &esdhc_imx51_data, }, 364 { .compatible = "fsl,imx53-esdhc", .data = &esdhc_imx53_data, }, 365 { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, }, 366 { .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, }, 367 { .compatible = "fsl,imx6sll-usdhc", .data = &usdhc_imx6sll_data, }, 368 { .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, }, 369 { .compatible = "fsl,imx6ull-usdhc", .data = &usdhc_imx6ull_data, }, 370 { .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, }, 371 { .compatible = "fsl,imx7ulp-usdhc", .data = &usdhc_imx7ulp_data, }, 372 { .compatible = "fsl,imx8qxp-usdhc", .data = &usdhc_imx8qxp_data, }, 373 { .compatible = "fsl,imx8mm-usdhc", .data = &usdhc_imx8mm_data, }, 374 { .compatible = "fsl,imxrt1050-usdhc", .data = &usdhc_imxrt1050_data, }, 375 { .compatible = "nxp,s32g2-usdhc", .data = &usdhc_s32g2_data, }, 376 { /* sentinel */ } 377 }; 378 MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids); 379 380 static inline int is_imx25_esdhc(struct pltfm_imx_data *data) 381 { 382 return data->socdata == &esdhc_imx25_data; 383 } 384 385 static inline int is_imx53_esdhc(struct pltfm_imx_data *data) 386 { 387 return data->socdata == &esdhc_imx53_data; 388 } 389 390 static inline int esdhc_is_usdhc(struct pltfm_imx_data *data) 391 { 392 return !!(data->socdata->flags & ESDHC_FLAG_USDHC); 393 } 394 395 static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, int reg) 396 { 397 void __iomem *base = host->ioaddr + (reg & ~0x3); 398 u32 shift = (reg & 0x3) * 8; 399 400 writel(((readl(base) & ~(mask << shift)) | (val << shift)), base); 401 } 402 403 #define DRIVER_NAME "sdhci-esdhc-imx" 404 #define ESDHC_IMX_DUMP(f, x...) \ 405 pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x) 406 static void esdhc_dump_debug_regs(struct sdhci_host *host) 407 { 408 int i; 409 char *debug_status[7] = { 410 "cmd debug status", 411 "data debug status", 412 "trans debug status", 413 "dma debug status", 414 "adma debug status", 415 "fifo debug status", 416 "async fifo debug status" 417 }; 418 419 ESDHC_IMX_DUMP("========= ESDHC IMX DEBUG STATUS DUMP =========\n"); 420 for (i = 0; i < 7; i++) { 421 esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK, 422 ESDHC_DEBUG_SEL_CMD_STATE + i, ESDHC_DEBUG_SEL_REG); 423 ESDHC_IMX_DUMP("%s: 0x%04x\n", debug_status[i], 424 readw(host->ioaddr + ESDHC_DEBUG_SEL_AND_STATUS_REG)); 425 } 426 427 esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK, 0, ESDHC_DEBUG_SEL_REG); 428 429 } 430 431 static inline void esdhc_wait_for_card_clock_gate_off(struct sdhci_host *host) 432 { 433 u32 present_state; 434 int ret; 435 436 ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, present_state, 437 (present_state & ESDHC_CLOCK_GATE_OFF), 2, 100); 438 if (ret == -ETIMEDOUT) 439 dev_warn(mmc_dev(host->mmc), "%s: card clock still not gate off in 100us!.\n", __func__); 440 } 441 442 /* Enable the auto tuning circuit to check the CMD line and BUS line */ 443 static inline void usdhc_auto_tuning_mode_sel_and_en(struct sdhci_host *host) 444 { 445 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 446 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 447 u32 buswidth, auto_tune_buswidth; 448 u32 reg; 449 450 buswidth = USDHC_GET_BUSWIDTH(readl(host->ioaddr + SDHCI_HOST_CONTROL)); 451 452 switch (buswidth) { 453 case ESDHC_CTRL_8BITBUS: 454 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN; 455 break; 456 case ESDHC_CTRL_4BITBUS: 457 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN; 458 break; 459 default: /* 1BITBUS */ 460 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN; 461 break; 462 } 463 464 /* 465 * For USDHC, auto tuning circuit can not handle the async sdio 466 * device interrupt correctly. When sdio device use 4 data lines, 467 * async sdio interrupt will use the shared DAT[1], if enable auto 468 * tuning circuit check these 4 data lines, include the DAT[1], 469 * this circuit will detect this interrupt, take this as a data on 470 * DAT[1], and adjust the delay cell wrongly. 471 * This is the hardware design limitation, to avoid this, for sdio 472 * device, config the auto tuning circuit only check DAT[0] and CMD 473 * line. 474 */ 475 if (imx_data->init_card_type == MMC_TYPE_SDIO) 476 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN; 477 478 esdhc_clrset_le(host, ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK, 479 auto_tune_buswidth | ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN, 480 ESDHC_VEND_SPEC2); 481 482 reg = readl(host->ioaddr + ESDHC_MIX_CTRL); 483 reg |= ESDHC_MIX_CTRL_AUTO_TUNE_EN; 484 writel(reg, host->ioaddr + ESDHC_MIX_CTRL); 485 } 486 487 static u32 esdhc_readl_le(struct sdhci_host *host, int reg) 488 { 489 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 490 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 491 u32 val = readl(host->ioaddr + reg); 492 493 if (unlikely(reg == SDHCI_PRESENT_STATE)) { 494 u32 fsl_prss = val; 495 /* save the least 20 bits */ 496 val = fsl_prss & 0x000FFFFF; 497 /* move dat[0-3] bits */ 498 val |= (fsl_prss & 0x0F000000) >> 4; 499 /* move cmd line bit */ 500 val |= (fsl_prss & 0x00800000) << 1; 501 } 502 503 if (unlikely(reg == SDHCI_CAPABILITIES)) { 504 /* ignore bit[0-15] as it stores cap_1 register val for mx6sl */ 505 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1) 506 val &= 0xffff0000; 507 508 /* In FSL esdhc IC module, only bit20 is used to indicate the 509 * ADMA2 capability of esdhc, but this bit is messed up on 510 * some SOCs (e.g. on MX25, MX35 this bit is set, but they 511 * don't actually support ADMA2). So set the BROKEN_ADMA 512 * quirk on MX25/35 platforms. 513 */ 514 515 if (val & SDHCI_CAN_DO_ADMA1) { 516 val &= ~SDHCI_CAN_DO_ADMA1; 517 val |= SDHCI_CAN_DO_ADMA2; 518 } 519 } 520 521 if (unlikely(reg == SDHCI_CAPABILITIES_1)) { 522 if (esdhc_is_usdhc(imx_data)) { 523 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1) 524 val = readl(host->ioaddr + SDHCI_CAPABILITIES) & 0xFFFF; 525 else 526 /* imx6q/dl does not have cap_1 register, fake one */ 527 val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104 528 | SDHCI_SUPPORT_SDR50 529 | SDHCI_USE_SDR50_TUNING 530 | FIELD_PREP(SDHCI_RETUNING_MODE_MASK, 531 SDHCI_TUNING_MODE_3); 532 533 /* 534 * Do not advertise faster UHS modes if there are no 535 * pinctrl states for 100MHz/200MHz. 536 */ 537 if (IS_ERR_OR_NULL(imx_data->pins_100mhz)) 538 val &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50); 539 if (IS_ERR_OR_NULL(imx_data->pins_200mhz)) 540 val &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_HS400); 541 } 542 } 543 544 if (unlikely(reg == SDHCI_MAX_CURRENT) && esdhc_is_usdhc(imx_data)) { 545 val = 0; 546 val |= FIELD_PREP(SDHCI_MAX_CURRENT_330_MASK, 0xFF); 547 val |= FIELD_PREP(SDHCI_MAX_CURRENT_300_MASK, 0xFF); 548 val |= FIELD_PREP(SDHCI_MAX_CURRENT_180_MASK, 0xFF); 549 } 550 551 if (unlikely(reg == SDHCI_INT_STATUS)) { 552 if (val & ESDHC_INT_VENDOR_SPEC_DMA_ERR) { 553 val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR; 554 val |= SDHCI_INT_ADMA_ERROR; 555 } 556 557 /* 558 * mask off the interrupt we get in response to the manually 559 * sent CMD12 560 */ 561 if ((imx_data->multiblock_status == WAIT_FOR_INT) && 562 ((val & SDHCI_INT_RESPONSE) == SDHCI_INT_RESPONSE)) { 563 val &= ~SDHCI_INT_RESPONSE; 564 writel(SDHCI_INT_RESPONSE, host->ioaddr + 565 SDHCI_INT_STATUS); 566 imx_data->multiblock_status = NO_CMD_PENDING; 567 } 568 } 569 570 return val; 571 } 572 573 static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg) 574 { 575 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 576 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 577 u32 data; 578 579 if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE || 580 reg == SDHCI_INT_STATUS)) { 581 if ((val & SDHCI_INT_CARD_INT) && !esdhc_is_usdhc(imx_data)) { 582 /* 583 * Clear and then set D3CD bit to avoid missing the 584 * card interrupt. This is an eSDHC controller problem 585 * so we need to apply the following workaround: clear 586 * and set D3CD bit will make eSDHC re-sample the card 587 * interrupt. In case a card interrupt was lost, 588 * re-sample it by the following steps. 589 */ 590 data = readl(host->ioaddr + SDHCI_HOST_CONTROL); 591 data &= ~ESDHC_CTRL_D3CD; 592 writel(data, host->ioaddr + SDHCI_HOST_CONTROL); 593 data |= ESDHC_CTRL_D3CD; 594 writel(data, host->ioaddr + SDHCI_HOST_CONTROL); 595 } 596 597 if (val & SDHCI_INT_ADMA_ERROR) { 598 val &= ~SDHCI_INT_ADMA_ERROR; 599 val |= ESDHC_INT_VENDOR_SPEC_DMA_ERR; 600 } 601 } 602 603 if (unlikely((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT) 604 && (reg == SDHCI_INT_STATUS) 605 && (val & SDHCI_INT_DATA_END))) { 606 u32 v; 607 v = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 608 v &= ~ESDHC_VENDOR_SPEC_SDIO_QUIRK; 609 writel(v, host->ioaddr + ESDHC_VENDOR_SPEC); 610 611 if (imx_data->multiblock_status == MULTIBLK_IN_PROCESS) 612 { 613 /* send a manual CMD12 with RESPTYP=none */ 614 data = MMC_STOP_TRANSMISSION << 24 | 615 SDHCI_CMD_ABORTCMD << 16; 616 writel(data, host->ioaddr + SDHCI_TRANSFER_MODE); 617 imx_data->multiblock_status = WAIT_FOR_INT; 618 } 619 } 620 621 writel(val, host->ioaddr + reg); 622 } 623 624 static u16 esdhc_readw_le(struct sdhci_host *host, int reg) 625 { 626 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 627 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 628 u16 ret = 0; 629 u32 val; 630 631 if (unlikely(reg == SDHCI_HOST_VERSION)) { 632 reg ^= 2; 633 if (esdhc_is_usdhc(imx_data)) { 634 /* 635 * The usdhc register returns a wrong host version. 636 * Correct it here. 637 */ 638 return SDHCI_SPEC_300; 639 } 640 } 641 642 if (unlikely(reg == SDHCI_HOST_CONTROL2)) { 643 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 644 if (val & ESDHC_VENDOR_SPEC_VSELECT) 645 ret |= SDHCI_CTRL_VDD_180; 646 647 if (esdhc_is_usdhc(imx_data)) { 648 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) 649 val = readl(host->ioaddr + ESDHC_MIX_CTRL); 650 else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) 651 /* the std tuning bits is in ACMD12_ERR for imx6sl */ 652 val = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS); 653 } 654 655 if (val & ESDHC_MIX_CTRL_EXE_TUNE) 656 ret |= SDHCI_CTRL_EXEC_TUNING; 657 if (val & ESDHC_MIX_CTRL_SMPCLK_SEL) 658 ret |= SDHCI_CTRL_TUNED_CLK; 659 660 ret &= ~SDHCI_CTRL_PRESET_VAL_ENABLE; 661 662 return ret; 663 } 664 665 if (unlikely(reg == SDHCI_TRANSFER_MODE)) { 666 if (esdhc_is_usdhc(imx_data)) { 667 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL); 668 ret = m & ESDHC_MIX_CTRL_SDHCI_MASK; 669 /* Swap AC23 bit */ 670 if (m & ESDHC_MIX_CTRL_AC23EN) { 671 ret &= ~ESDHC_MIX_CTRL_AC23EN; 672 ret |= SDHCI_TRNS_AUTO_CMD23; 673 } 674 } else { 675 ret = readw(host->ioaddr + SDHCI_TRANSFER_MODE); 676 } 677 678 return ret; 679 } 680 681 return readw(host->ioaddr + reg); 682 } 683 684 static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg) 685 { 686 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 687 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 688 u32 new_val = 0; 689 690 switch (reg) { 691 case SDHCI_CLOCK_CONTROL: 692 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 693 if (val & SDHCI_CLOCK_CARD_EN) 694 new_val |= ESDHC_VENDOR_SPEC_FRC_SDCLK_ON; 695 else 696 new_val &= ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON; 697 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC); 698 if (!(new_val & ESDHC_VENDOR_SPEC_FRC_SDCLK_ON)) 699 esdhc_wait_for_card_clock_gate_off(host); 700 return; 701 case SDHCI_HOST_CONTROL2: 702 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 703 if (val & SDHCI_CTRL_VDD_180) 704 new_val |= ESDHC_VENDOR_SPEC_VSELECT; 705 else 706 new_val &= ~ESDHC_VENDOR_SPEC_VSELECT; 707 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC); 708 if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) { 709 u32 v = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS); 710 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL); 711 if (val & SDHCI_CTRL_TUNED_CLK) { 712 v |= ESDHC_MIX_CTRL_SMPCLK_SEL; 713 } else { 714 v &= ~ESDHC_MIX_CTRL_SMPCLK_SEL; 715 m &= ~ESDHC_MIX_CTRL_FBCLK_SEL; 716 } 717 718 if (val & SDHCI_CTRL_EXEC_TUNING) { 719 v |= ESDHC_MIX_CTRL_EXE_TUNE; 720 m |= ESDHC_MIX_CTRL_FBCLK_SEL; 721 } else { 722 v &= ~ESDHC_MIX_CTRL_EXE_TUNE; 723 } 724 725 writel(v, host->ioaddr + SDHCI_AUTO_CMD_STATUS); 726 writel(m, host->ioaddr + ESDHC_MIX_CTRL); 727 } 728 return; 729 case SDHCI_TRANSFER_MODE: 730 if ((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT) 731 && (host->cmd->opcode == SD_IO_RW_EXTENDED) 732 && (host->cmd->data->blocks > 1) 733 && (host->cmd->data->flags & MMC_DATA_READ)) { 734 u32 v; 735 v = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 736 v |= ESDHC_VENDOR_SPEC_SDIO_QUIRK; 737 writel(v, host->ioaddr + ESDHC_VENDOR_SPEC); 738 } 739 740 if (esdhc_is_usdhc(imx_data)) { 741 u32 wml; 742 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL); 743 /* Swap AC23 bit */ 744 if (val & SDHCI_TRNS_AUTO_CMD23) { 745 val &= ~SDHCI_TRNS_AUTO_CMD23; 746 val |= ESDHC_MIX_CTRL_AC23EN; 747 } 748 m = val | (m & ~ESDHC_MIX_CTRL_SDHCI_MASK); 749 writel(m, host->ioaddr + ESDHC_MIX_CTRL); 750 751 /* Set watermark levels for PIO access to maximum value 752 * (128 words) to accommodate full 512 bytes buffer. 753 * For DMA access restore the levels to default value. 754 */ 755 m = readl(host->ioaddr + ESDHC_WTMK_LVL); 756 if (val & SDHCI_TRNS_DMA) { 757 wml = ESDHC_WTMK_LVL_WML_VAL_DEF; 758 } else { 759 u8 ctrl; 760 wml = ESDHC_WTMK_LVL_WML_VAL_MAX; 761 762 /* 763 * Since already disable DMA mode, so also need 764 * to clear the DMASEL. Otherwise, for standard 765 * tuning, when send tuning command, usdhc will 766 * still prefetch the ADMA script from wrong 767 * DMA address, then we will see IOMMU report 768 * some error which show lack of TLB mapping. 769 */ 770 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL); 771 ctrl &= ~SDHCI_CTRL_DMA_MASK; 772 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL); 773 } 774 m &= ~(ESDHC_WTMK_LVL_RD_WML_MASK | 775 ESDHC_WTMK_LVL_WR_WML_MASK); 776 m |= (wml << ESDHC_WTMK_LVL_RD_WML_SHIFT) | 777 (wml << ESDHC_WTMK_LVL_WR_WML_SHIFT); 778 writel(m, host->ioaddr + ESDHC_WTMK_LVL); 779 } else { 780 /* 781 * Postpone this write, we must do it together with a 782 * command write that is down below. 783 */ 784 imx_data->scratchpad = val; 785 } 786 return; 787 case SDHCI_COMMAND: 788 if (host->cmd->opcode == MMC_STOP_TRANSMISSION) 789 val |= SDHCI_CMD_ABORTCMD; 790 791 if ((host->cmd->opcode == MMC_SET_BLOCK_COUNT) && 792 (imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)) 793 imx_data->multiblock_status = MULTIBLK_IN_PROCESS; 794 795 if (esdhc_is_usdhc(imx_data)) 796 writel(val << 16, 797 host->ioaddr + SDHCI_TRANSFER_MODE); 798 else 799 writel(val << 16 | imx_data->scratchpad, 800 host->ioaddr + SDHCI_TRANSFER_MODE); 801 return; 802 case SDHCI_BLOCK_SIZE: 803 val &= ~SDHCI_MAKE_BLKSZ(0x7, 0); 804 break; 805 } 806 esdhc_clrset_le(host, 0xffff, val, reg); 807 } 808 809 static u8 esdhc_readb_le(struct sdhci_host *host, int reg) 810 { 811 u8 ret; 812 u32 val; 813 814 switch (reg) { 815 case SDHCI_HOST_CONTROL: 816 val = readl(host->ioaddr + reg); 817 818 ret = val & SDHCI_CTRL_LED; 819 ret |= (val >> 5) & SDHCI_CTRL_DMA_MASK; 820 ret |= (val & ESDHC_CTRL_4BITBUS); 821 ret |= (val & ESDHC_CTRL_8BITBUS) << 3; 822 return ret; 823 } 824 825 return readb(host->ioaddr + reg); 826 } 827 828 static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg) 829 { 830 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 831 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 832 u32 new_val = 0; 833 u32 mask; 834 835 switch (reg) { 836 case SDHCI_POWER_CONTROL: 837 /* 838 * FSL put some DMA bits here 839 * If your board has a regulator, code should be here 840 */ 841 return; 842 case SDHCI_HOST_CONTROL: 843 /* FSL messed up here, so we need to manually compose it. */ 844 new_val = val & SDHCI_CTRL_LED; 845 /* ensure the endianness */ 846 new_val |= ESDHC_HOST_CONTROL_LE; 847 /* bits 8&9 are reserved on mx25 */ 848 if (!is_imx25_esdhc(imx_data)) { 849 /* DMA mode bits are shifted */ 850 new_val |= (val & SDHCI_CTRL_DMA_MASK) << 5; 851 } 852 853 /* 854 * Do not touch buswidth bits here. This is done in 855 * esdhc_pltfm_bus_width. 856 * Do not touch the D3CD bit either which is used for the 857 * SDIO interrupt erratum workaround. 858 */ 859 mask = 0xffff & ~(ESDHC_CTRL_BUSWIDTH_MASK | ESDHC_CTRL_D3CD); 860 861 esdhc_clrset_le(host, mask, new_val, reg); 862 return; 863 case SDHCI_SOFTWARE_RESET: 864 if (val & SDHCI_RESET_DATA) 865 new_val = readl(host->ioaddr + SDHCI_HOST_CONTROL); 866 break; 867 } 868 esdhc_clrset_le(host, 0xff, val, reg); 869 870 if (reg == SDHCI_SOFTWARE_RESET) { 871 if (val & SDHCI_RESET_ALL) { 872 /* 873 * The esdhc has a design violation to SDHC spec which 874 * tells that software reset should not affect card 875 * detection circuit. But esdhc clears its SYSCTL 876 * register bits [0..2] during the software reset. This 877 * will stop those clocks that card detection circuit 878 * relies on. To work around it, we turn the clocks on 879 * back to keep card detection circuit functional. 880 */ 881 esdhc_clrset_le(host, 0x7, 0x7, ESDHC_SYSTEM_CONTROL); 882 /* 883 * The reset on usdhc fails to clear MIX_CTRL register. 884 * Do it manually here. 885 */ 886 if (esdhc_is_usdhc(imx_data)) { 887 /* 888 * the tuning bits should be kept during reset 889 */ 890 new_val = readl(host->ioaddr + ESDHC_MIX_CTRL); 891 writel(new_val & ESDHC_MIX_CTRL_TUNING_MASK, 892 host->ioaddr + ESDHC_MIX_CTRL); 893 imx_data->is_ddr = 0; 894 } 895 } else if (val & SDHCI_RESET_DATA) { 896 /* 897 * The eSDHC DAT line software reset clears at least the 898 * data transfer width on i.MX25, so make sure that the 899 * Host Control register is unaffected. 900 */ 901 esdhc_clrset_le(host, 0xff, new_val, 902 SDHCI_HOST_CONTROL); 903 } 904 } 905 } 906 907 static unsigned int esdhc_pltfm_get_max_clock(struct sdhci_host *host) 908 { 909 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 910 911 return pltfm_host->clock; 912 } 913 914 static unsigned int esdhc_pltfm_get_min_clock(struct sdhci_host *host) 915 { 916 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 917 918 return pltfm_host->clock / 256 / 16; 919 } 920 921 static inline void esdhc_pltfm_set_clock(struct sdhci_host *host, 922 unsigned int clock) 923 { 924 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 925 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 926 unsigned int host_clock = pltfm_host->clock; 927 int ddr_pre_div = imx_data->is_ddr ? 2 : 1; 928 int pre_div = 1; 929 int div = 1; 930 int ret; 931 u32 temp, val; 932 933 if (esdhc_is_usdhc(imx_data)) { 934 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 935 writel(val & ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, 936 host->ioaddr + ESDHC_VENDOR_SPEC); 937 esdhc_wait_for_card_clock_gate_off(host); 938 } 939 940 if (clock == 0) { 941 host->mmc->actual_clock = 0; 942 return; 943 } 944 945 /* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */ 946 if (is_imx53_esdhc(imx_data)) { 947 /* 948 * According to the i.MX53 reference manual, if DLLCTRL[10] can 949 * be set, then the controller is eSDHCv3, else it is eSDHCv2. 950 */ 951 val = readl(host->ioaddr + ESDHC_DLL_CTRL); 952 writel(val | BIT(10), host->ioaddr + ESDHC_DLL_CTRL); 953 temp = readl(host->ioaddr + ESDHC_DLL_CTRL); 954 writel(val, host->ioaddr + ESDHC_DLL_CTRL); 955 if (temp & BIT(10)) 956 pre_div = 2; 957 } 958 959 temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL); 960 temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN 961 | ESDHC_CLOCK_MASK); 962 sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL); 963 964 if (imx_data->socdata->flags & ESDHC_FLAG_ERR010450) { 965 unsigned int max_clock; 966 967 max_clock = imx_data->is_ddr ? 45000000 : 150000000; 968 969 clock = min(clock, max_clock); 970 } 971 972 while (host_clock / (16 * pre_div * ddr_pre_div) > clock && 973 pre_div < 256) 974 pre_div *= 2; 975 976 while (host_clock / (div * pre_div * ddr_pre_div) > clock && div < 16) 977 div++; 978 979 host->mmc->actual_clock = host_clock / (div * pre_div * ddr_pre_div); 980 dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n", 981 clock, host->mmc->actual_clock); 982 983 pre_div >>= 1; 984 div--; 985 986 temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL); 987 temp |= (ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN 988 | (div << ESDHC_DIVIDER_SHIFT) 989 | (pre_div << ESDHC_PREDIV_SHIFT)); 990 sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL); 991 992 /* need to wait the bit 3 of the PRSSTAT to be set, make sure card clock is stable */ 993 ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, temp, 994 (temp & ESDHC_CLOCK_STABLE), 2, 100); 995 if (ret == -ETIMEDOUT) 996 dev_warn(mmc_dev(host->mmc), "card clock still not stable in 100us!.\n"); 997 998 if (esdhc_is_usdhc(imx_data)) { 999 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 1000 writel(val | ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, 1001 host->ioaddr + ESDHC_VENDOR_SPEC); 1002 } 1003 1004 } 1005 1006 static unsigned int esdhc_pltfm_get_ro(struct sdhci_host *host) 1007 { 1008 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1009 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1010 struct esdhc_platform_data *boarddata = &imx_data->boarddata; 1011 1012 switch (boarddata->wp_type) { 1013 case ESDHC_WP_GPIO: 1014 return mmc_gpio_get_ro(host->mmc); 1015 case ESDHC_WP_CONTROLLER: 1016 return !(readl(host->ioaddr + SDHCI_PRESENT_STATE) & 1017 SDHCI_WRITE_PROTECT); 1018 case ESDHC_WP_NONE: 1019 break; 1020 } 1021 1022 return -ENOSYS; 1023 } 1024 1025 static void esdhc_pltfm_set_bus_width(struct sdhci_host *host, int width) 1026 { 1027 u32 ctrl; 1028 1029 switch (width) { 1030 case MMC_BUS_WIDTH_8: 1031 ctrl = ESDHC_CTRL_8BITBUS; 1032 break; 1033 case MMC_BUS_WIDTH_4: 1034 ctrl = ESDHC_CTRL_4BITBUS; 1035 break; 1036 default: 1037 ctrl = 0; 1038 break; 1039 } 1040 1041 esdhc_clrset_le(host, ESDHC_CTRL_BUSWIDTH_MASK, ctrl, 1042 SDHCI_HOST_CONTROL); 1043 } 1044 1045 static void esdhc_reset_tuning(struct sdhci_host *host) 1046 { 1047 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1048 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1049 u32 ctrl; 1050 int ret; 1051 1052 /* Reset the tuning circuit */ 1053 if (esdhc_is_usdhc(imx_data)) { 1054 ctrl = readl(host->ioaddr + ESDHC_MIX_CTRL); 1055 ctrl &= ~ESDHC_MIX_CTRL_AUTO_TUNE_EN; 1056 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) { 1057 ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL; 1058 ctrl &= ~ESDHC_MIX_CTRL_FBCLK_SEL; 1059 writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL); 1060 writel(0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS); 1061 } else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) { 1062 writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL); 1063 ctrl = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS); 1064 ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL; 1065 ctrl &= ~ESDHC_MIX_CTRL_EXE_TUNE; 1066 writel(ctrl, host->ioaddr + SDHCI_AUTO_CMD_STATUS); 1067 /* Make sure ESDHC_MIX_CTRL_EXE_TUNE cleared */ 1068 ret = readl_poll_timeout(host->ioaddr + SDHCI_AUTO_CMD_STATUS, 1069 ctrl, !(ctrl & ESDHC_MIX_CTRL_EXE_TUNE), 1, 50); 1070 if (ret == -ETIMEDOUT) 1071 dev_warn(mmc_dev(host->mmc), 1072 "Warning! clear execute tuning bit failed\n"); 1073 /* 1074 * SDHCI_INT_DATA_AVAIL is W1C bit, set this bit will clear the 1075 * usdhc IP internal logic flag execute_tuning_with_clr_buf, which 1076 * will finally make sure the normal data transfer logic correct. 1077 */ 1078 ctrl = readl(host->ioaddr + SDHCI_INT_STATUS); 1079 ctrl |= SDHCI_INT_DATA_AVAIL; 1080 writel(ctrl, host->ioaddr + SDHCI_INT_STATUS); 1081 } 1082 } 1083 } 1084 1085 static void usdhc_init_card(struct mmc_host *mmc, struct mmc_card *card) 1086 { 1087 struct sdhci_host *host = mmc_priv(mmc); 1088 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1089 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1090 1091 imx_data->init_card_type = card->type; 1092 } 1093 1094 static int usdhc_execute_tuning(struct mmc_host *mmc, u32 opcode) 1095 { 1096 struct sdhci_host *host = mmc_priv(mmc); 1097 int err; 1098 1099 /* 1100 * i.MX uSDHC internally already uses a fixed optimized timing for 1101 * DDR50, normally does not require tuning for DDR50 mode. 1102 */ 1103 if (host->timing == MMC_TIMING_UHS_DDR50) 1104 return 0; 1105 1106 /* 1107 * Reset tuning circuit logic. If not, the previous tuning result 1108 * will impact current tuning, make current tuning can't set the 1109 * correct delay cell. 1110 */ 1111 esdhc_reset_tuning(host); 1112 err = sdhci_execute_tuning(mmc, opcode); 1113 /* If tuning done, enable auto tuning */ 1114 if (!err && !host->tuning_err) 1115 usdhc_auto_tuning_mode_sel_and_en(host); 1116 1117 return err; 1118 } 1119 1120 static void esdhc_prepare_tuning(struct sdhci_host *host, u32 val) 1121 { 1122 u32 reg; 1123 u8 sw_rst; 1124 int ret; 1125 1126 /* FIXME: delay a bit for card to be ready for next tuning due to errors */ 1127 mdelay(1); 1128 1129 /* IC suggest to reset USDHC before every tuning command */ 1130 esdhc_clrset_le(host, 0xff, SDHCI_RESET_ALL, SDHCI_SOFTWARE_RESET); 1131 ret = readb_poll_timeout(host->ioaddr + SDHCI_SOFTWARE_RESET, sw_rst, 1132 !(sw_rst & SDHCI_RESET_ALL), 10, 100); 1133 if (ret == -ETIMEDOUT) 1134 dev_warn(mmc_dev(host->mmc), 1135 "warning! RESET_ALL never complete before sending tuning command\n"); 1136 1137 reg = readl(host->ioaddr + ESDHC_MIX_CTRL); 1138 reg |= ESDHC_MIX_CTRL_EXE_TUNE | ESDHC_MIX_CTRL_SMPCLK_SEL | 1139 ESDHC_MIX_CTRL_FBCLK_SEL; 1140 writel(reg, host->ioaddr + ESDHC_MIX_CTRL); 1141 writel(val << 8, host->ioaddr + ESDHC_TUNE_CTRL_STATUS); 1142 dev_dbg(mmc_dev(host->mmc), 1143 "tuning with delay 0x%x ESDHC_TUNE_CTRL_STATUS 0x%x\n", 1144 val, readl(host->ioaddr + ESDHC_TUNE_CTRL_STATUS)); 1145 } 1146 1147 static void esdhc_post_tuning(struct sdhci_host *host) 1148 { 1149 u32 reg; 1150 1151 reg = readl(host->ioaddr + ESDHC_MIX_CTRL); 1152 reg &= ~ESDHC_MIX_CTRL_EXE_TUNE; 1153 writel(reg, host->ioaddr + ESDHC_MIX_CTRL); 1154 } 1155 1156 static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode) 1157 { 1158 int min, max, avg, ret; 1159 1160 /* find the mininum delay first which can pass tuning */ 1161 min = ESDHC_TUNE_CTRL_MIN; 1162 while (min < ESDHC_TUNE_CTRL_MAX) { 1163 esdhc_prepare_tuning(host, min); 1164 if (!mmc_send_tuning(host->mmc, opcode, NULL)) 1165 break; 1166 min += ESDHC_TUNE_CTRL_STEP; 1167 } 1168 1169 /* find the maxinum delay which can not pass tuning */ 1170 max = min + ESDHC_TUNE_CTRL_STEP; 1171 while (max < ESDHC_TUNE_CTRL_MAX) { 1172 esdhc_prepare_tuning(host, max); 1173 if (mmc_send_tuning(host->mmc, opcode, NULL)) { 1174 max -= ESDHC_TUNE_CTRL_STEP; 1175 break; 1176 } 1177 max += ESDHC_TUNE_CTRL_STEP; 1178 } 1179 1180 /* use average delay to get the best timing */ 1181 avg = (min + max) / 2; 1182 esdhc_prepare_tuning(host, avg); 1183 ret = mmc_send_tuning(host->mmc, opcode, NULL); 1184 esdhc_post_tuning(host); 1185 1186 dev_dbg(mmc_dev(host->mmc), "tuning %s at 0x%x ret %d\n", 1187 ret ? "failed" : "passed", avg, ret); 1188 1189 return ret; 1190 } 1191 1192 static void esdhc_hs400_enhanced_strobe(struct mmc_host *mmc, struct mmc_ios *ios) 1193 { 1194 struct sdhci_host *host = mmc_priv(mmc); 1195 u32 m; 1196 1197 m = readl(host->ioaddr + ESDHC_MIX_CTRL); 1198 if (ios->enhanced_strobe) 1199 m |= ESDHC_MIX_CTRL_HS400_ES_EN; 1200 else 1201 m &= ~ESDHC_MIX_CTRL_HS400_ES_EN; 1202 writel(m, host->ioaddr + ESDHC_MIX_CTRL); 1203 } 1204 1205 static int esdhc_change_pinstate(struct sdhci_host *host, 1206 unsigned int uhs) 1207 { 1208 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1209 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1210 struct pinctrl_state *pinctrl; 1211 1212 dev_dbg(mmc_dev(host->mmc), "change pinctrl state for uhs %d\n", uhs); 1213 1214 if (IS_ERR(imx_data->pinctrl) || 1215 IS_ERR(imx_data->pins_100mhz) || 1216 IS_ERR(imx_data->pins_200mhz)) 1217 return -EINVAL; 1218 1219 switch (uhs) { 1220 case MMC_TIMING_UHS_SDR50: 1221 case MMC_TIMING_UHS_DDR50: 1222 pinctrl = imx_data->pins_100mhz; 1223 break; 1224 case MMC_TIMING_UHS_SDR104: 1225 case MMC_TIMING_MMC_HS200: 1226 case MMC_TIMING_MMC_HS400: 1227 pinctrl = imx_data->pins_200mhz; 1228 break; 1229 default: 1230 /* back to default state for other legacy timing */ 1231 return pinctrl_select_default_state(mmc_dev(host->mmc)); 1232 } 1233 1234 return pinctrl_select_state(imx_data->pinctrl, pinctrl); 1235 } 1236 1237 /* 1238 * For HS400 eMMC, there is a data_strobe line. This signal is generated 1239 * by the device and used for data output and CRC status response output 1240 * in HS400 mode. The frequency of this signal follows the frequency of 1241 * CLK generated by host. The host receives the data which is aligned to the 1242 * edge of data_strobe line. Due to the time delay between CLK line and 1243 * data_strobe line, if the delay time is larger than one clock cycle, 1244 * then CLK and data_strobe line will be misaligned, read error shows up. 1245 */ 1246 static void esdhc_set_strobe_dll(struct sdhci_host *host) 1247 { 1248 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1249 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1250 u32 strobe_delay; 1251 u32 v; 1252 int ret; 1253 1254 /* disable clock before enabling strobe dll */ 1255 writel(readl(host->ioaddr + ESDHC_VENDOR_SPEC) & 1256 ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, 1257 host->ioaddr + ESDHC_VENDOR_SPEC); 1258 esdhc_wait_for_card_clock_gate_off(host); 1259 1260 /* force a reset on strobe dll */ 1261 writel(ESDHC_STROBE_DLL_CTRL_RESET, 1262 host->ioaddr + ESDHC_STROBE_DLL_CTRL); 1263 /* clear the reset bit on strobe dll before any setting */ 1264 writel(0, host->ioaddr + ESDHC_STROBE_DLL_CTRL); 1265 1266 /* 1267 * enable strobe dll ctrl and adjust the delay target 1268 * for the uSDHC loopback read clock 1269 */ 1270 if (imx_data->boarddata.strobe_dll_delay_target) 1271 strobe_delay = imx_data->boarddata.strobe_dll_delay_target; 1272 else 1273 strobe_delay = ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT; 1274 v = ESDHC_STROBE_DLL_CTRL_ENABLE | 1275 ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT | 1276 (strobe_delay << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT); 1277 writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL); 1278 1279 /* wait max 50us to get the REF/SLV lock */ 1280 ret = readl_poll_timeout(host->ioaddr + ESDHC_STROBE_DLL_STATUS, v, 1281 ((v & ESDHC_STROBE_DLL_STS_REF_LOCK) && (v & ESDHC_STROBE_DLL_STS_SLV_LOCK)), 1, 50); 1282 if (ret == -ETIMEDOUT) 1283 dev_warn(mmc_dev(host->mmc), 1284 "warning! HS400 strobe DLL status REF/SLV not lock in 50us, STROBE DLL status is %x!\n", v); 1285 } 1286 1287 static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing) 1288 { 1289 u32 m; 1290 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1291 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1292 struct esdhc_platform_data *boarddata = &imx_data->boarddata; 1293 1294 /* disable ddr mode and disable HS400 mode */ 1295 m = readl(host->ioaddr + ESDHC_MIX_CTRL); 1296 m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN); 1297 imx_data->is_ddr = 0; 1298 1299 switch (timing) { 1300 case MMC_TIMING_UHS_SDR12: 1301 case MMC_TIMING_UHS_SDR25: 1302 case MMC_TIMING_UHS_SDR50: 1303 case MMC_TIMING_UHS_SDR104: 1304 case MMC_TIMING_MMC_HS: 1305 case MMC_TIMING_MMC_HS200: 1306 writel(m, host->ioaddr + ESDHC_MIX_CTRL); 1307 break; 1308 case MMC_TIMING_UHS_DDR50: 1309 case MMC_TIMING_MMC_DDR52: 1310 m |= ESDHC_MIX_CTRL_DDREN; 1311 writel(m, host->ioaddr + ESDHC_MIX_CTRL); 1312 imx_data->is_ddr = 1; 1313 if (boarddata->delay_line) { 1314 u32 v; 1315 v = boarddata->delay_line << 1316 ESDHC_DLL_OVERRIDE_VAL_SHIFT | 1317 (1 << ESDHC_DLL_OVERRIDE_EN_SHIFT); 1318 if (is_imx53_esdhc(imx_data)) 1319 v <<= 1; 1320 writel(v, host->ioaddr + ESDHC_DLL_CTRL); 1321 } 1322 break; 1323 case MMC_TIMING_MMC_HS400: 1324 m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN; 1325 writel(m, host->ioaddr + ESDHC_MIX_CTRL); 1326 imx_data->is_ddr = 1; 1327 /* update clock after enable DDR for strobe DLL lock */ 1328 host->ops->set_clock(host, host->clock); 1329 esdhc_set_strobe_dll(host); 1330 break; 1331 case MMC_TIMING_LEGACY: 1332 default: 1333 esdhc_reset_tuning(host); 1334 break; 1335 } 1336 1337 esdhc_change_pinstate(host, timing); 1338 } 1339 1340 static void esdhc_reset(struct sdhci_host *host, u8 mask) 1341 { 1342 sdhci_and_cqhci_reset(host, mask); 1343 1344 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE); 1345 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE); 1346 } 1347 1348 static unsigned int esdhc_get_max_timeout_count(struct sdhci_host *host) 1349 { 1350 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1351 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1352 1353 /* Doc Erratum: the uSDHC actual maximum timeout count is 1 << 29 */ 1354 return esdhc_is_usdhc(imx_data) ? 1 << 29 : 1 << 27; 1355 } 1356 1357 static void esdhc_set_timeout(struct sdhci_host *host, struct mmc_command *cmd) 1358 { 1359 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1360 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1361 1362 /* use maximum timeout counter */ 1363 esdhc_clrset_le(host, ESDHC_SYS_CTRL_DTOCV_MASK, 1364 esdhc_is_usdhc(imx_data) ? 0xF : 0xE, 1365 SDHCI_TIMEOUT_CONTROL); 1366 } 1367 1368 static u32 esdhc_cqhci_irq(struct sdhci_host *host, u32 intmask) 1369 { 1370 int cmd_error = 0; 1371 int data_error = 0; 1372 1373 if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error)) 1374 return intmask; 1375 1376 cqhci_irq(host->mmc, intmask, cmd_error, data_error); 1377 1378 return 0; 1379 } 1380 1381 static struct sdhci_ops sdhci_esdhc_ops = { 1382 .read_l = esdhc_readl_le, 1383 .read_w = esdhc_readw_le, 1384 .read_b = esdhc_readb_le, 1385 .write_l = esdhc_writel_le, 1386 .write_w = esdhc_writew_le, 1387 .write_b = esdhc_writeb_le, 1388 .set_clock = esdhc_pltfm_set_clock, 1389 .get_max_clock = esdhc_pltfm_get_max_clock, 1390 .get_min_clock = esdhc_pltfm_get_min_clock, 1391 .get_max_timeout_count = esdhc_get_max_timeout_count, 1392 .get_ro = esdhc_pltfm_get_ro, 1393 .set_timeout = esdhc_set_timeout, 1394 .set_bus_width = esdhc_pltfm_set_bus_width, 1395 .set_uhs_signaling = esdhc_set_uhs_signaling, 1396 .reset = esdhc_reset, 1397 .irq = esdhc_cqhci_irq, 1398 .dump_vendor_regs = esdhc_dump_debug_regs, 1399 }; 1400 1401 static const struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = { 1402 .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT 1403 | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC 1404 | SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC 1405 | SDHCI_QUIRK_BROKEN_CARD_DETECTION, 1406 .ops = &sdhci_esdhc_ops, 1407 }; 1408 1409 static void sdhci_esdhc_imx_hwinit(struct sdhci_host *host) 1410 { 1411 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1412 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1413 struct cqhci_host *cq_host = host->mmc->cqe_private; 1414 u32 tmp; 1415 1416 if (esdhc_is_usdhc(imx_data)) { 1417 /* 1418 * The imx6q ROM code will change the default watermark 1419 * level setting to something insane. Change it back here. 1420 */ 1421 writel(ESDHC_WTMK_DEFAULT_VAL, host->ioaddr + ESDHC_WTMK_LVL); 1422 1423 /* 1424 * ROM code will change the bit burst_length_enable setting 1425 * to zero if this usdhc is chosen to boot system. Change 1426 * it back here, otherwise it will impact the performance a 1427 * lot. This bit is used to enable/disable the burst length 1428 * for the external AHB2AXI bridge. It's useful especially 1429 * for INCR transfer because without burst length indicator, 1430 * the AHB2AXI bridge does not know the burst length in 1431 * advance. And without burst length indicator, AHB INCR 1432 * transfer can only be converted to singles on the AXI side. 1433 */ 1434 writel(readl(host->ioaddr + SDHCI_HOST_CONTROL) 1435 | ESDHC_BURST_LEN_EN_INCR, 1436 host->ioaddr + SDHCI_HOST_CONTROL); 1437 1438 /* 1439 * erratum ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL 1440 * TO1.1, it's harmless for MX6SL 1441 */ 1442 if (!(imx_data->socdata->flags & ESDHC_FLAG_SKIP_ERR004536)) { 1443 writel(readl(host->ioaddr + 0x6c) & ~BIT(7), 1444 host->ioaddr + 0x6c); 1445 } 1446 1447 /* disable DLL_CTRL delay line settings */ 1448 writel(0x0, host->ioaddr + ESDHC_DLL_CTRL); 1449 1450 /* 1451 * For the case of command with busy, if set the bit 1452 * ESDHC_VEND_SPEC2_EN_BUSY_IRQ, USDHC will generate a 1453 * transfer complete interrupt when busy is deasserted. 1454 * When CQHCI use DCMD to send a CMD need R1b respons, 1455 * CQHCI require to set ESDHC_VEND_SPEC2_EN_BUSY_IRQ, 1456 * otherwise DCMD will always meet timeout waiting for 1457 * hardware interrupt issue. 1458 */ 1459 if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) { 1460 tmp = readl(host->ioaddr + ESDHC_VEND_SPEC2); 1461 tmp |= ESDHC_VEND_SPEC2_EN_BUSY_IRQ; 1462 writel(tmp, host->ioaddr + ESDHC_VEND_SPEC2); 1463 1464 host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ; 1465 } 1466 1467 if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) { 1468 tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL); 1469 tmp |= ESDHC_STD_TUNING_EN; 1470 1471 /* 1472 * ROM code or bootloader may config the start tap 1473 * and step, unmask them first. 1474 */ 1475 tmp &= ~(ESDHC_TUNING_START_TAP_MASK | ESDHC_TUNING_STEP_MASK); 1476 if (imx_data->boarddata.tuning_start_tap) 1477 tmp |= imx_data->boarddata.tuning_start_tap; 1478 else 1479 tmp |= ESDHC_TUNING_START_TAP_DEFAULT; 1480 1481 if (imx_data->boarddata.tuning_step) { 1482 tmp |= imx_data->boarddata.tuning_step 1483 << ESDHC_TUNING_STEP_SHIFT; 1484 } else { 1485 tmp |= ESDHC_TUNING_STEP_DEFAULT 1486 << ESDHC_TUNING_STEP_SHIFT; 1487 } 1488 1489 /* Disable the CMD CRC check for tuning, if not, need to 1490 * add some delay after every tuning command, because 1491 * hardware standard tuning logic will directly go to next 1492 * step once it detect the CMD CRC error, will not wait for 1493 * the card side to finally send out the tuning data, trigger 1494 * the buffer read ready interrupt immediately. If usdhc send 1495 * the next tuning command some eMMC card will stuck, can't 1496 * response, block the tuning procedure or the first command 1497 * after the whole tuning procedure always can't get any response. 1498 */ 1499 tmp |= ESDHC_TUNING_CMD_CRC_CHECK_DISABLE; 1500 writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL); 1501 } else if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) { 1502 /* 1503 * ESDHC_STD_TUNING_EN may be configed in bootloader 1504 * or ROM code, so clear this bit here to make sure 1505 * the manual tuning can work. 1506 */ 1507 tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL); 1508 tmp &= ~ESDHC_STD_TUNING_EN; 1509 writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL); 1510 } 1511 1512 /* 1513 * On i.MX8MM, we are running Dual Linux OS, with 1st Linux using SD Card 1514 * as rootfs storage, 2nd Linux using eMMC as rootfs storage. We let 1515 * the 1st linux configure power/clock for the 2nd Linux. 1516 * 1517 * When the 2nd Linux is booting into rootfs stage, we let the 1st Linux 1518 * to destroy the 2nd linux, then restart the 2nd linux, we met SDHCI dump. 1519 * After we clear the pending interrupt and halt CQCTL, issue gone. 1520 */ 1521 if (cq_host) { 1522 tmp = cqhci_readl(cq_host, CQHCI_IS); 1523 cqhci_writel(cq_host, tmp, CQHCI_IS); 1524 cqhci_writel(cq_host, CQHCI_HALT, CQHCI_CTL); 1525 } 1526 } 1527 } 1528 1529 static void esdhc_cqe_enable(struct mmc_host *mmc) 1530 { 1531 struct sdhci_host *host = mmc_priv(mmc); 1532 struct cqhci_host *cq_host = mmc->cqe_private; 1533 u32 reg; 1534 u16 mode; 1535 int count = 10; 1536 1537 /* 1538 * CQE gets stuck if it sees Buffer Read Enable bit set, which can be 1539 * the case after tuning, so ensure the buffer is drained. 1540 */ 1541 reg = sdhci_readl(host, SDHCI_PRESENT_STATE); 1542 while (reg & SDHCI_DATA_AVAILABLE) { 1543 sdhci_readl(host, SDHCI_BUFFER); 1544 reg = sdhci_readl(host, SDHCI_PRESENT_STATE); 1545 if (count-- == 0) { 1546 dev_warn(mmc_dev(host->mmc), 1547 "CQE may get stuck because the Buffer Read Enable bit is set\n"); 1548 break; 1549 } 1550 mdelay(1); 1551 } 1552 1553 /* 1554 * Runtime resume will reset the entire host controller, which 1555 * will also clear the DMAEN/BCEN of register ESDHC_MIX_CTRL. 1556 * Here set DMAEN and BCEN when enable CMDQ. 1557 */ 1558 mode = sdhci_readw(host, SDHCI_TRANSFER_MODE); 1559 if (host->flags & SDHCI_REQ_USE_DMA) 1560 mode |= SDHCI_TRNS_DMA; 1561 if (!(host->quirks2 & SDHCI_QUIRK2_SUPPORT_SINGLE)) 1562 mode |= SDHCI_TRNS_BLK_CNT_EN; 1563 sdhci_writew(host, mode, SDHCI_TRANSFER_MODE); 1564 1565 /* 1566 * Though Runtime resume reset the entire host controller, 1567 * but do not impact the CQHCI side, need to clear the 1568 * HALT bit, avoid CQHCI stuck in the first request when 1569 * system resume back. 1570 */ 1571 cqhci_writel(cq_host, 0, CQHCI_CTL); 1572 if (cqhci_readl(cq_host, CQHCI_CTL) & CQHCI_HALT) 1573 dev_err(mmc_dev(host->mmc), 1574 "failed to exit halt state when enable CQE\n"); 1575 1576 1577 sdhci_cqe_enable(mmc); 1578 } 1579 1580 static void esdhc_sdhci_dumpregs(struct mmc_host *mmc) 1581 { 1582 sdhci_dumpregs(mmc_priv(mmc)); 1583 } 1584 1585 static const struct cqhci_host_ops esdhc_cqhci_ops = { 1586 .enable = esdhc_cqe_enable, 1587 .disable = sdhci_cqe_disable, 1588 .dumpregs = esdhc_sdhci_dumpregs, 1589 }; 1590 1591 static int 1592 sdhci_esdhc_imx_probe_dt(struct platform_device *pdev, 1593 struct sdhci_host *host, 1594 struct pltfm_imx_data *imx_data) 1595 { 1596 struct device_node *np = pdev->dev.of_node; 1597 struct esdhc_platform_data *boarddata = &imx_data->boarddata; 1598 int ret; 1599 1600 if (of_get_property(np, "fsl,wp-controller", NULL)) 1601 boarddata->wp_type = ESDHC_WP_CONTROLLER; 1602 1603 /* 1604 * If we have this property, then activate WP check. 1605 * Retrieveing and requesting the actual WP GPIO will happen 1606 * in the call to mmc_of_parse(). 1607 */ 1608 if (of_property_read_bool(np, "wp-gpios")) 1609 boarddata->wp_type = ESDHC_WP_GPIO; 1610 1611 of_property_read_u32(np, "fsl,tuning-step", &boarddata->tuning_step); 1612 of_property_read_u32(np, "fsl,tuning-start-tap", 1613 &boarddata->tuning_start_tap); 1614 1615 of_property_read_u32(np, "fsl,strobe-dll-delay-target", 1616 &boarddata->strobe_dll_delay_target); 1617 if (of_find_property(np, "no-1-8-v", NULL)) 1618 host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V; 1619 1620 if (of_property_read_u32(np, "fsl,delay-line", &boarddata->delay_line)) 1621 boarddata->delay_line = 0; 1622 1623 mmc_of_parse_voltage(host->mmc, &host->ocr_mask); 1624 1625 if (esdhc_is_usdhc(imx_data) && !IS_ERR(imx_data->pinctrl)) { 1626 imx_data->pins_100mhz = pinctrl_lookup_state(imx_data->pinctrl, 1627 ESDHC_PINCTRL_STATE_100MHZ); 1628 imx_data->pins_200mhz = pinctrl_lookup_state(imx_data->pinctrl, 1629 ESDHC_PINCTRL_STATE_200MHZ); 1630 } 1631 1632 /* call to generic mmc_of_parse to support additional capabilities */ 1633 ret = mmc_of_parse(host->mmc); 1634 if (ret) 1635 return ret; 1636 1637 if (mmc_gpio_get_cd(host->mmc) >= 0) 1638 host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION; 1639 1640 return 0; 1641 } 1642 1643 static int sdhci_esdhc_imx_probe(struct platform_device *pdev) 1644 { 1645 struct sdhci_pltfm_host *pltfm_host; 1646 struct sdhci_host *host; 1647 struct cqhci_host *cq_host; 1648 int err; 1649 struct pltfm_imx_data *imx_data; 1650 1651 host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata, 1652 sizeof(*imx_data)); 1653 if (IS_ERR(host)) 1654 return PTR_ERR(host); 1655 1656 pltfm_host = sdhci_priv(host); 1657 1658 imx_data = sdhci_pltfm_priv(pltfm_host); 1659 1660 imx_data->socdata = device_get_match_data(&pdev->dev); 1661 1662 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS) 1663 cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0); 1664 1665 imx_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg"); 1666 if (IS_ERR(imx_data->clk_ipg)) { 1667 err = PTR_ERR(imx_data->clk_ipg); 1668 goto free_sdhci; 1669 } 1670 1671 imx_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb"); 1672 if (IS_ERR(imx_data->clk_ahb)) { 1673 err = PTR_ERR(imx_data->clk_ahb); 1674 goto free_sdhci; 1675 } 1676 1677 imx_data->clk_per = devm_clk_get(&pdev->dev, "per"); 1678 if (IS_ERR(imx_data->clk_per)) { 1679 err = PTR_ERR(imx_data->clk_per); 1680 goto free_sdhci; 1681 } 1682 1683 pltfm_host->clk = imx_data->clk_per; 1684 pltfm_host->clock = clk_get_rate(pltfm_host->clk); 1685 err = clk_prepare_enable(imx_data->clk_per); 1686 if (err) 1687 goto free_sdhci; 1688 err = clk_prepare_enable(imx_data->clk_ipg); 1689 if (err) 1690 goto disable_per_clk; 1691 err = clk_prepare_enable(imx_data->clk_ahb); 1692 if (err) 1693 goto disable_ipg_clk; 1694 1695 imx_data->pinctrl = devm_pinctrl_get(&pdev->dev); 1696 if (IS_ERR(imx_data->pinctrl)) 1697 dev_warn(mmc_dev(host->mmc), "could not get pinctrl\n"); 1698 1699 if (esdhc_is_usdhc(imx_data)) { 1700 host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN; 1701 host->mmc->caps |= MMC_CAP_1_8V_DDR | MMC_CAP_3_3V_DDR; 1702 1703 /* GPIO CD can be set as a wakeup source */ 1704 host->mmc->caps |= MMC_CAP_CD_WAKE; 1705 1706 if (!(imx_data->socdata->flags & ESDHC_FLAG_HS200)) 1707 host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200; 1708 1709 /* clear tuning bits in case ROM has set it already */ 1710 writel(0x0, host->ioaddr + ESDHC_MIX_CTRL); 1711 writel(0x0, host->ioaddr + SDHCI_AUTO_CMD_STATUS); 1712 writel(0x0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS); 1713 1714 /* 1715 * Link usdhc specific mmc_host_ops execute_tuning function, 1716 * to replace the standard one in sdhci_ops. 1717 */ 1718 host->mmc_host_ops.execute_tuning = usdhc_execute_tuning; 1719 1720 /* 1721 * Link usdhc specific mmc_host_ops init card function, 1722 * to distinguish the card type. 1723 */ 1724 host->mmc_host_ops.init_card = usdhc_init_card; 1725 } 1726 1727 err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data); 1728 if (err) 1729 goto disable_ahb_clk; 1730 1731 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) 1732 sdhci_esdhc_ops.platform_execute_tuning = 1733 esdhc_executing_tuning; 1734 1735 if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536) 1736 host->quirks |= SDHCI_QUIRK_BROKEN_ADMA; 1737 1738 if (host->mmc->caps & MMC_CAP_8_BIT_DATA && 1739 imx_data->socdata->flags & ESDHC_FLAG_HS400) 1740 host->mmc->caps2 |= MMC_CAP2_HS400; 1741 1742 if (imx_data->socdata->flags & ESDHC_FLAG_BROKEN_AUTO_CMD23) 1743 host->quirks2 |= SDHCI_QUIRK2_ACMD23_BROKEN; 1744 1745 if (host->mmc->caps & MMC_CAP_8_BIT_DATA && 1746 imx_data->socdata->flags & ESDHC_FLAG_HS400_ES) { 1747 host->mmc->caps2 |= MMC_CAP2_HS400_ES; 1748 host->mmc_host_ops.hs400_enhanced_strobe = 1749 esdhc_hs400_enhanced_strobe; 1750 } 1751 1752 if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) { 1753 host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD; 1754 cq_host = devm_kzalloc(&pdev->dev, sizeof(*cq_host), GFP_KERNEL); 1755 if (!cq_host) { 1756 err = -ENOMEM; 1757 goto disable_ahb_clk; 1758 } 1759 1760 cq_host->mmio = host->ioaddr + ESDHC_CQHCI_ADDR_OFFSET; 1761 cq_host->ops = &esdhc_cqhci_ops; 1762 1763 err = cqhci_init(cq_host, host->mmc, false); 1764 if (err) 1765 goto disable_ahb_clk; 1766 } 1767 1768 sdhci_esdhc_imx_hwinit(host); 1769 1770 err = sdhci_add_host(host); 1771 if (err) 1772 goto disable_ahb_clk; 1773 1774 /* 1775 * Setup the wakeup capability here, let user to decide 1776 * whether need to enable this wakeup through sysfs interface. 1777 */ 1778 if ((host->mmc->pm_caps & MMC_PM_KEEP_POWER) && 1779 (host->mmc->pm_caps & MMC_PM_WAKE_SDIO_IRQ)) 1780 device_set_wakeup_capable(&pdev->dev, true); 1781 1782 pm_runtime_set_active(&pdev->dev); 1783 pm_runtime_set_autosuspend_delay(&pdev->dev, 50); 1784 pm_runtime_use_autosuspend(&pdev->dev); 1785 pm_suspend_ignore_children(&pdev->dev, 1); 1786 pm_runtime_enable(&pdev->dev); 1787 1788 return 0; 1789 1790 disable_ahb_clk: 1791 clk_disable_unprepare(imx_data->clk_ahb); 1792 disable_ipg_clk: 1793 clk_disable_unprepare(imx_data->clk_ipg); 1794 disable_per_clk: 1795 clk_disable_unprepare(imx_data->clk_per); 1796 free_sdhci: 1797 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS) 1798 cpu_latency_qos_remove_request(&imx_data->pm_qos_req); 1799 sdhci_pltfm_free(pdev); 1800 return err; 1801 } 1802 1803 static int sdhci_esdhc_imx_remove(struct platform_device *pdev) 1804 { 1805 struct sdhci_host *host = platform_get_drvdata(pdev); 1806 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1807 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1808 int dead; 1809 1810 pm_runtime_get_sync(&pdev->dev); 1811 dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff); 1812 pm_runtime_disable(&pdev->dev); 1813 pm_runtime_put_noidle(&pdev->dev); 1814 1815 sdhci_remove_host(host, dead); 1816 1817 clk_disable_unprepare(imx_data->clk_per); 1818 clk_disable_unprepare(imx_data->clk_ipg); 1819 clk_disable_unprepare(imx_data->clk_ahb); 1820 1821 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS) 1822 cpu_latency_qos_remove_request(&imx_data->pm_qos_req); 1823 1824 sdhci_pltfm_free(pdev); 1825 1826 return 0; 1827 } 1828 1829 #ifdef CONFIG_PM_SLEEP 1830 static int sdhci_esdhc_suspend(struct device *dev) 1831 { 1832 struct sdhci_host *host = dev_get_drvdata(dev); 1833 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1834 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1835 int ret; 1836 1837 if (host->mmc->caps2 & MMC_CAP2_CQE) { 1838 ret = cqhci_suspend(host->mmc); 1839 if (ret) 1840 return ret; 1841 } 1842 1843 if ((imx_data->socdata->flags & ESDHC_FLAG_STATE_LOST_IN_LPMODE) && 1844 (host->tuning_mode != SDHCI_TUNING_MODE_1)) { 1845 mmc_retune_timer_stop(host->mmc); 1846 mmc_retune_needed(host->mmc); 1847 } 1848 1849 if (host->tuning_mode != SDHCI_TUNING_MODE_3) 1850 mmc_retune_needed(host->mmc); 1851 1852 ret = sdhci_suspend_host(host); 1853 if (ret) 1854 return ret; 1855 1856 ret = pinctrl_pm_select_sleep_state(dev); 1857 if (ret) 1858 return ret; 1859 1860 ret = mmc_gpio_set_cd_wake(host->mmc, true); 1861 1862 return ret; 1863 } 1864 1865 static int sdhci_esdhc_resume(struct device *dev) 1866 { 1867 struct sdhci_host *host = dev_get_drvdata(dev); 1868 int ret; 1869 1870 ret = pinctrl_pm_select_default_state(dev); 1871 if (ret) 1872 return ret; 1873 1874 /* re-initialize hw state in case it's lost in low power mode */ 1875 sdhci_esdhc_imx_hwinit(host); 1876 1877 ret = sdhci_resume_host(host); 1878 if (ret) 1879 return ret; 1880 1881 if (host->mmc->caps2 & MMC_CAP2_CQE) 1882 ret = cqhci_resume(host->mmc); 1883 1884 if (!ret) 1885 ret = mmc_gpio_set_cd_wake(host->mmc, false); 1886 1887 return ret; 1888 } 1889 #endif 1890 1891 #ifdef CONFIG_PM 1892 static int sdhci_esdhc_runtime_suspend(struct device *dev) 1893 { 1894 struct sdhci_host *host = dev_get_drvdata(dev); 1895 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1896 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1897 int ret; 1898 1899 if (host->mmc->caps2 & MMC_CAP2_CQE) { 1900 ret = cqhci_suspend(host->mmc); 1901 if (ret) 1902 return ret; 1903 } 1904 1905 ret = sdhci_runtime_suspend_host(host); 1906 if (ret) 1907 return ret; 1908 1909 if (host->tuning_mode != SDHCI_TUNING_MODE_3) 1910 mmc_retune_needed(host->mmc); 1911 1912 imx_data->actual_clock = host->mmc->actual_clock; 1913 esdhc_pltfm_set_clock(host, 0); 1914 clk_disable_unprepare(imx_data->clk_per); 1915 clk_disable_unprepare(imx_data->clk_ipg); 1916 clk_disable_unprepare(imx_data->clk_ahb); 1917 1918 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS) 1919 cpu_latency_qos_remove_request(&imx_data->pm_qos_req); 1920 1921 return ret; 1922 } 1923 1924 static int sdhci_esdhc_runtime_resume(struct device *dev) 1925 { 1926 struct sdhci_host *host = dev_get_drvdata(dev); 1927 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1928 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1929 int err; 1930 1931 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS) 1932 cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0); 1933 1934 if (imx_data->socdata->flags & ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME) 1935 clk_set_rate(imx_data->clk_per, pltfm_host->clock); 1936 1937 err = clk_prepare_enable(imx_data->clk_ahb); 1938 if (err) 1939 goto remove_pm_qos_request; 1940 1941 err = clk_prepare_enable(imx_data->clk_per); 1942 if (err) 1943 goto disable_ahb_clk; 1944 1945 err = clk_prepare_enable(imx_data->clk_ipg); 1946 if (err) 1947 goto disable_per_clk; 1948 1949 esdhc_pltfm_set_clock(host, imx_data->actual_clock); 1950 1951 err = sdhci_runtime_resume_host(host, 0); 1952 if (err) 1953 goto disable_ipg_clk; 1954 1955 if (host->mmc->caps2 & MMC_CAP2_CQE) 1956 err = cqhci_resume(host->mmc); 1957 1958 return err; 1959 1960 disable_ipg_clk: 1961 clk_disable_unprepare(imx_data->clk_ipg); 1962 disable_per_clk: 1963 clk_disable_unprepare(imx_data->clk_per); 1964 disable_ahb_clk: 1965 clk_disable_unprepare(imx_data->clk_ahb); 1966 remove_pm_qos_request: 1967 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS) 1968 cpu_latency_qos_remove_request(&imx_data->pm_qos_req); 1969 return err; 1970 } 1971 #endif 1972 1973 static const struct dev_pm_ops sdhci_esdhc_pmops = { 1974 SET_SYSTEM_SLEEP_PM_OPS(sdhci_esdhc_suspend, sdhci_esdhc_resume) 1975 SET_RUNTIME_PM_OPS(sdhci_esdhc_runtime_suspend, 1976 sdhci_esdhc_runtime_resume, NULL) 1977 }; 1978 1979 static struct platform_driver sdhci_esdhc_imx_driver = { 1980 .driver = { 1981 .name = "sdhci-esdhc-imx", 1982 .probe_type = PROBE_PREFER_ASYNCHRONOUS, 1983 .of_match_table = imx_esdhc_dt_ids, 1984 .pm = &sdhci_esdhc_pmops, 1985 }, 1986 .probe = sdhci_esdhc_imx_probe, 1987 .remove = sdhci_esdhc_imx_remove, 1988 }; 1989 1990 module_platform_driver(sdhci_esdhc_imx_driver); 1991 1992 MODULE_DESCRIPTION("SDHCI driver for Freescale i.MX eSDHC"); 1993 MODULE_AUTHOR("Wolfram Sang <kernel@pengutronix.de>"); 1994 MODULE_LICENSE("GPL v2"); 1995