1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * Freescale eSDHC i.MX controller driver for the platform bus.
4  *
5  * derived from the OF-version.
6  *
7  * Copyright (c) 2010 Pengutronix e.K.
8  *   Author: Wolfram Sang <kernel@pengutronix.de>
9  */
10 
11 #include <linux/bitfield.h>
12 #include <linux/io.h>
13 #include <linux/iopoll.h>
14 #include <linux/delay.h>
15 #include <linux/err.h>
16 #include <linux/clk.h>
17 #include <linux/module.h>
18 #include <linux/slab.h>
19 #include <linux/pm_qos.h>
20 #include <linux/mmc/host.h>
21 #include <linux/mmc/mmc.h>
22 #include <linux/mmc/sdio.h>
23 #include <linux/mmc/slot-gpio.h>
24 #include <linux/of.h>
25 #include <linux/of_device.h>
26 #include <linux/pinctrl/consumer.h>
27 #include <linux/pm_runtime.h>
28 #include "sdhci-cqhci.h"
29 #include "sdhci-pltfm.h"
30 #include "sdhci-esdhc.h"
31 #include "cqhci.h"
32 
33 #define ESDHC_SYS_CTRL_DTOCV_MASK	0x0f
34 #define	ESDHC_CTRL_D3CD			0x08
35 #define ESDHC_BURST_LEN_EN_INCR		(1 << 27)
36 /* VENDOR SPEC register */
37 #define ESDHC_VENDOR_SPEC		0xc0
38 #define  ESDHC_VENDOR_SPEC_SDIO_QUIRK	(1 << 1)
39 #define  ESDHC_VENDOR_SPEC_VSELECT	(1 << 1)
40 #define  ESDHC_VENDOR_SPEC_FRC_SDCLK_ON	(1 << 8)
41 #define ESDHC_DEBUG_SEL_AND_STATUS_REG		0xc2
42 #define ESDHC_DEBUG_SEL_REG			0xc3
43 #define ESDHC_DEBUG_SEL_MASK			0xf
44 #define ESDHC_DEBUG_SEL_CMD_STATE		1
45 #define ESDHC_DEBUG_SEL_DATA_STATE		2
46 #define ESDHC_DEBUG_SEL_TRANS_STATE		3
47 #define ESDHC_DEBUG_SEL_DMA_STATE		4
48 #define ESDHC_DEBUG_SEL_ADMA_STATE		5
49 #define ESDHC_DEBUG_SEL_FIFO_STATE		6
50 #define ESDHC_DEBUG_SEL_ASYNC_FIFO_STATE	7
51 #define ESDHC_WTMK_LVL			0x44
52 #define  ESDHC_WTMK_DEFAULT_VAL		0x10401040
53 #define  ESDHC_WTMK_LVL_RD_WML_MASK	0x000000FF
54 #define  ESDHC_WTMK_LVL_RD_WML_SHIFT	0
55 #define  ESDHC_WTMK_LVL_WR_WML_MASK	0x00FF0000
56 #define  ESDHC_WTMK_LVL_WR_WML_SHIFT	16
57 #define  ESDHC_WTMK_LVL_WML_VAL_DEF	64
58 #define  ESDHC_WTMK_LVL_WML_VAL_MAX	128
59 #define ESDHC_MIX_CTRL			0x48
60 #define  ESDHC_MIX_CTRL_DDREN		(1 << 3)
61 #define  ESDHC_MIX_CTRL_AC23EN		(1 << 7)
62 #define  ESDHC_MIX_CTRL_EXE_TUNE	(1 << 22)
63 #define  ESDHC_MIX_CTRL_SMPCLK_SEL	(1 << 23)
64 #define  ESDHC_MIX_CTRL_AUTO_TUNE_EN	(1 << 24)
65 #define  ESDHC_MIX_CTRL_FBCLK_SEL	(1 << 25)
66 #define  ESDHC_MIX_CTRL_HS400_EN	(1 << 26)
67 #define  ESDHC_MIX_CTRL_HS400_ES_EN	(1 << 27)
68 /* Bits 3 and 6 are not SDHCI standard definitions */
69 #define  ESDHC_MIX_CTRL_SDHCI_MASK	0xb7
70 /* Tuning bits */
71 #define  ESDHC_MIX_CTRL_TUNING_MASK	0x03c00000
72 
73 /* dll control register */
74 #define ESDHC_DLL_CTRL			0x60
75 #define ESDHC_DLL_OVERRIDE_VAL_SHIFT	9
76 #define ESDHC_DLL_OVERRIDE_EN_SHIFT	8
77 
78 /* tune control register */
79 #define ESDHC_TUNE_CTRL_STATUS		0x68
80 #define  ESDHC_TUNE_CTRL_STEP		1
81 #define  ESDHC_TUNE_CTRL_MIN		0
82 #define  ESDHC_TUNE_CTRL_MAX		((1 << 7) - 1)
83 
84 /* strobe dll register */
85 #define ESDHC_STROBE_DLL_CTRL		0x70
86 #define ESDHC_STROBE_DLL_CTRL_ENABLE	(1 << 0)
87 #define ESDHC_STROBE_DLL_CTRL_RESET	(1 << 1)
88 #define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT	0x7
89 #define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT	3
90 #define ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT	(4 << 20)
91 
92 #define ESDHC_STROBE_DLL_STATUS		0x74
93 #define ESDHC_STROBE_DLL_STS_REF_LOCK	(1 << 1)
94 #define ESDHC_STROBE_DLL_STS_SLV_LOCK	0x1
95 
96 #define ESDHC_VEND_SPEC2		0xc8
97 #define ESDHC_VEND_SPEC2_EN_BUSY_IRQ	(1 << 8)
98 #define ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN	(1 << 4)
99 #define ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN	(0 << 4)
100 #define ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN	(2 << 4)
101 #define ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN	(1 << 6)
102 #define ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK	(7 << 4)
103 
104 #define ESDHC_TUNING_CTRL		0xcc
105 #define ESDHC_STD_TUNING_EN		(1 << 24)
106 /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
107 #define ESDHC_TUNING_START_TAP_DEFAULT	0x1
108 #define ESDHC_TUNING_START_TAP_MASK	0x7f
109 #define ESDHC_TUNING_CMD_CRC_CHECK_DISABLE	(1 << 7)
110 #define ESDHC_TUNING_STEP_DEFAULT	0x1
111 #define ESDHC_TUNING_STEP_MASK		0x00070000
112 #define ESDHC_TUNING_STEP_SHIFT		16
113 
114 /* pinctrl state */
115 #define ESDHC_PINCTRL_STATE_100MHZ	"state_100mhz"
116 #define ESDHC_PINCTRL_STATE_200MHZ	"state_200mhz"
117 
118 /*
119  * Our interpretation of the SDHCI_HOST_CONTROL register
120  */
121 #define ESDHC_CTRL_4BITBUS		(0x1 << 1)
122 #define ESDHC_CTRL_8BITBUS		(0x2 << 1)
123 #define ESDHC_CTRL_BUSWIDTH_MASK	(0x3 << 1)
124 #define USDHC_GET_BUSWIDTH(c) (c & ESDHC_CTRL_BUSWIDTH_MASK)
125 
126 /*
127  * There is an INT DMA ERR mismatch between eSDHC and STD SDHC SPEC:
128  * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
129  * but bit28 is used as the INT DMA ERR in fsl eSDHC design.
130  * Define this macro DMA error INT for fsl eSDHC
131  */
132 #define ESDHC_INT_VENDOR_SPEC_DMA_ERR	(1 << 28)
133 
134 /* the address offset of CQHCI */
135 #define ESDHC_CQHCI_ADDR_OFFSET		0x100
136 
137 /*
138  * The CMDTYPE of the CMD register (offset 0xE) should be set to
139  * "11" when the STOP CMD12 is issued on imx53 to abort one
140  * open ended multi-blk IO. Otherwise the TC INT wouldn't
141  * be generated.
142  * In exact block transfer, the controller doesn't complete the
143  * operations automatically as required at the end of the
144  * transfer and remains on hold if the abort command is not sent.
145  * As a result, the TC flag is not asserted and SW received timeout
146  * exception. Bit1 of Vendor Spec register is used to fix it.
147  */
148 #define ESDHC_FLAG_MULTIBLK_NO_INT	BIT(1)
149 /*
150  * The flag tells that the ESDHC controller is an USDHC block that is
151  * integrated on the i.MX6 series.
152  */
153 #define ESDHC_FLAG_USDHC		BIT(3)
154 /* The IP supports manual tuning process */
155 #define ESDHC_FLAG_MAN_TUNING		BIT(4)
156 /* The IP supports standard tuning process */
157 #define ESDHC_FLAG_STD_TUNING		BIT(5)
158 /* The IP has SDHCI_CAPABILITIES_1 register */
159 #define ESDHC_FLAG_HAVE_CAP1		BIT(6)
160 /*
161  * The IP has erratum ERR004536
162  * uSDHC: ADMA Length Mismatch Error occurs if the AHB read access is slow,
163  * when reading data from the card
164  * This flag is also set for i.MX25 and i.MX35 in order to get
165  * SDHCI_QUIRK_BROKEN_ADMA, but for different reasons (ADMA capability bits).
166  */
167 #define ESDHC_FLAG_ERR004536		BIT(7)
168 /* The IP supports HS200 mode */
169 #define ESDHC_FLAG_HS200		BIT(8)
170 /* The IP supports HS400 mode */
171 #define ESDHC_FLAG_HS400		BIT(9)
172 /*
173  * The IP has errata ERR010450
174  * uSDHC: Due to the I/O timing limit, for SDR mode, SD card clock can't
175  * exceed 150MHz, for DDR mode, SD card clock can't exceed 45MHz.
176  */
177 #define ESDHC_FLAG_ERR010450		BIT(10)
178 /* The IP supports HS400ES mode */
179 #define ESDHC_FLAG_HS400_ES		BIT(11)
180 /* The IP has Host Controller Interface for Command Queuing */
181 #define ESDHC_FLAG_CQHCI		BIT(12)
182 /* need request pmqos during low power */
183 #define ESDHC_FLAG_PMQOS		BIT(13)
184 /* The IP state got lost in low power mode */
185 #define ESDHC_FLAG_STATE_LOST_IN_LPMODE		BIT(14)
186 /* The IP lost clock rate in PM_RUNTIME */
187 #define ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME	BIT(15)
188 /*
189  * The IP do not support the ACMD23 feature completely when use ADMA mode.
190  * In ADMA mode, it only use the 16 bit block count of the register 0x4
191  * (BLOCK_ATT) as the CMD23's argument for ACMD23 mode, which means it will
192  * ignore the upper 16 bit of the CMD23's argument. This will block the reliable
193  * write operation in RPMB, because RPMB reliable write need to set the bit31
194  * of the CMD23's argument.
195  * imx6qpdl/imx6sx/imx6sl/imx7d has this limitation only for ADMA mode, SDMA
196  * do not has this limitation. so when these SoC use ADMA mode, it need to
197  * disable the ACMD23 feature.
198  */
199 #define ESDHC_FLAG_BROKEN_AUTO_CMD23	BIT(16)
200 
201 /* ERR004536 is not applicable for the IP  */
202 #define ESDHC_FLAG_SKIP_ERR004536	BIT(17)
203 
204 enum wp_types {
205 	ESDHC_WP_NONE,		/* no WP, neither controller nor gpio */
206 	ESDHC_WP_CONTROLLER,	/* mmc controller internal WP */
207 	ESDHC_WP_GPIO,		/* external gpio pin for WP */
208 };
209 
210 enum cd_types {
211 	ESDHC_CD_NONE,		/* no CD, neither controller nor gpio */
212 	ESDHC_CD_CONTROLLER,	/* mmc controller internal CD */
213 	ESDHC_CD_GPIO,		/* external gpio pin for CD */
214 	ESDHC_CD_PERMANENT,	/* no CD, card permanently wired to host */
215 };
216 
217 /*
218  * struct esdhc_platform_data - platform data for esdhc on i.MX
219  *
220  * ESDHC_WP(CD)_CONTROLLER type is not available on i.MX25/35.
221  *
222  * @wp_type:	type of write_protect method (see wp_types enum above)
223  * @cd_type:	type of card_detect method (see cd_types enum above)
224  */
225 
226 struct esdhc_platform_data {
227 	enum wp_types wp_type;
228 	enum cd_types cd_type;
229 	int max_bus_width;
230 	unsigned int delay_line;
231 	unsigned int tuning_step;       /* The delay cell steps in tuning procedure */
232 	unsigned int tuning_start_tap;	/* The start delay cell point in tuning procedure */
233 	unsigned int strobe_dll_delay_target;	/* The delay cell for strobe pad (read clock) */
234 };
235 
236 struct esdhc_soc_data {
237 	u32 flags;
238 };
239 
240 static const struct esdhc_soc_data esdhc_imx25_data = {
241 	.flags = ESDHC_FLAG_ERR004536,
242 };
243 
244 static const struct esdhc_soc_data esdhc_imx35_data = {
245 	.flags = ESDHC_FLAG_ERR004536,
246 };
247 
248 static const struct esdhc_soc_data esdhc_imx51_data = {
249 	.flags = 0,
250 };
251 
252 static const struct esdhc_soc_data esdhc_imx53_data = {
253 	.flags = ESDHC_FLAG_MULTIBLK_NO_INT,
254 };
255 
256 static const struct esdhc_soc_data usdhc_imx6q_data = {
257 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING
258 			| ESDHC_FLAG_BROKEN_AUTO_CMD23,
259 };
260 
261 static const struct esdhc_soc_data usdhc_imx6sl_data = {
262 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
263 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_ERR004536
264 			| ESDHC_FLAG_HS200
265 			| ESDHC_FLAG_BROKEN_AUTO_CMD23,
266 };
267 
268 static const struct esdhc_soc_data usdhc_imx6sll_data = {
269 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
270 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
271 			| ESDHC_FLAG_HS400
272 			| ESDHC_FLAG_STATE_LOST_IN_LPMODE,
273 };
274 
275 static const struct esdhc_soc_data usdhc_imx6sx_data = {
276 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
277 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
278 			| ESDHC_FLAG_STATE_LOST_IN_LPMODE
279 			| ESDHC_FLAG_BROKEN_AUTO_CMD23,
280 };
281 
282 static const struct esdhc_soc_data usdhc_imx6ull_data = {
283 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
284 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
285 			| ESDHC_FLAG_ERR010450
286 			| ESDHC_FLAG_STATE_LOST_IN_LPMODE,
287 };
288 
289 static const struct esdhc_soc_data usdhc_imx7d_data = {
290 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
291 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
292 			| ESDHC_FLAG_HS400
293 			| ESDHC_FLAG_STATE_LOST_IN_LPMODE
294 			| ESDHC_FLAG_BROKEN_AUTO_CMD23,
295 };
296 
297 static struct esdhc_soc_data usdhc_s32g2_data = {
298 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING
299 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
300 			| ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
301 			| ESDHC_FLAG_SKIP_ERR004536,
302 };
303 
304 static struct esdhc_soc_data usdhc_imx7ulp_data = {
305 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
306 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
307 			| ESDHC_FLAG_PMQOS | ESDHC_FLAG_HS400
308 			| ESDHC_FLAG_STATE_LOST_IN_LPMODE,
309 };
310 static struct esdhc_soc_data usdhc_imxrt1050_data = {
311 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
312 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200,
313 };
314 
315 static struct esdhc_soc_data usdhc_imx8qxp_data = {
316 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
317 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
318 			| ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
319 			| ESDHC_FLAG_STATE_LOST_IN_LPMODE
320 			| ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME,
321 };
322 
323 static struct esdhc_soc_data usdhc_imx8mm_data = {
324 	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
325 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
326 			| ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
327 			| ESDHC_FLAG_STATE_LOST_IN_LPMODE,
328 };
329 
330 struct pltfm_imx_data {
331 	u32 scratchpad;
332 	struct pinctrl *pinctrl;
333 	struct pinctrl_state *pins_100mhz;
334 	struct pinctrl_state *pins_200mhz;
335 	const struct esdhc_soc_data *socdata;
336 	struct esdhc_platform_data boarddata;
337 	struct clk *clk_ipg;
338 	struct clk *clk_ahb;
339 	struct clk *clk_per;
340 	unsigned int actual_clock;
341 
342 	/*
343 	 * USDHC has one limition, require the SDIO device a different
344 	 * register setting. Driver has to recognize card type during
345 	 * the card init, but at this stage, mmc_host->card is not
346 	 * available. So involve this field to save the card type
347 	 * during card init through usdhc_init_card().
348 	 */
349 	unsigned int init_card_type;
350 
351 	enum {
352 		NO_CMD_PENDING,      /* no multiblock command pending */
353 		MULTIBLK_IN_PROCESS, /* exact multiblock cmd in process */
354 		WAIT_FOR_INT,        /* sent CMD12, waiting for response INT */
355 	} multiblock_status;
356 	u32 is_ddr;
357 	struct pm_qos_request pm_qos_req;
358 };
359 
360 static const struct of_device_id imx_esdhc_dt_ids[] = {
361 	{ .compatible = "fsl,imx25-esdhc", .data = &esdhc_imx25_data, },
362 	{ .compatible = "fsl,imx35-esdhc", .data = &esdhc_imx35_data, },
363 	{ .compatible = "fsl,imx51-esdhc", .data = &esdhc_imx51_data, },
364 	{ .compatible = "fsl,imx53-esdhc", .data = &esdhc_imx53_data, },
365 	{ .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
366 	{ .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
367 	{ .compatible = "fsl,imx6sll-usdhc", .data = &usdhc_imx6sll_data, },
368 	{ .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
369 	{ .compatible = "fsl,imx6ull-usdhc", .data = &usdhc_imx6ull_data, },
370 	{ .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
371 	{ .compatible = "fsl,imx7ulp-usdhc", .data = &usdhc_imx7ulp_data, },
372 	{ .compatible = "fsl,imx8qxp-usdhc", .data = &usdhc_imx8qxp_data, },
373 	{ .compatible = "fsl,imx8mm-usdhc", .data = &usdhc_imx8mm_data, },
374 	{ .compatible = "fsl,imxrt1050-usdhc", .data = &usdhc_imxrt1050_data, },
375 	{ .compatible = "nxp,s32g2-usdhc", .data = &usdhc_s32g2_data, },
376 	{ /* sentinel */ }
377 };
378 MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
379 
380 static inline int is_imx25_esdhc(struct pltfm_imx_data *data)
381 {
382 	return data->socdata == &esdhc_imx25_data;
383 }
384 
385 static inline int is_imx53_esdhc(struct pltfm_imx_data *data)
386 {
387 	return data->socdata == &esdhc_imx53_data;
388 }
389 
390 static inline int esdhc_is_usdhc(struct pltfm_imx_data *data)
391 {
392 	return !!(data->socdata->flags & ESDHC_FLAG_USDHC);
393 }
394 
395 static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, int reg)
396 {
397 	void __iomem *base = host->ioaddr + (reg & ~0x3);
398 	u32 shift = (reg & 0x3) * 8;
399 
400 	writel(((readl(base) & ~(mask << shift)) | (val << shift)), base);
401 }
402 
403 #define DRIVER_NAME "sdhci-esdhc-imx"
404 #define ESDHC_IMX_DUMP(f, x...) \
405 	pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
406 static void esdhc_dump_debug_regs(struct sdhci_host *host)
407 {
408 	int i;
409 	char *debug_status[7] = {
410 				 "cmd debug status",
411 				 "data debug status",
412 				 "trans debug status",
413 				 "dma debug status",
414 				 "adma debug status",
415 				 "fifo debug status",
416 				 "async fifo debug status"
417 	};
418 
419 	ESDHC_IMX_DUMP("========= ESDHC IMX DEBUG STATUS DUMP =========\n");
420 	for (i = 0; i < 7; i++) {
421 		esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK,
422 			ESDHC_DEBUG_SEL_CMD_STATE + i, ESDHC_DEBUG_SEL_REG);
423 		ESDHC_IMX_DUMP("%s:  0x%04x\n", debug_status[i],
424 			readw(host->ioaddr + ESDHC_DEBUG_SEL_AND_STATUS_REG));
425 	}
426 
427 	esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK, 0, ESDHC_DEBUG_SEL_REG);
428 
429 }
430 
431 static inline void esdhc_wait_for_card_clock_gate_off(struct sdhci_host *host)
432 {
433 	u32 present_state;
434 	int ret;
435 
436 	ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, present_state,
437 				(present_state & ESDHC_CLOCK_GATE_OFF), 2, 100);
438 	if (ret == -ETIMEDOUT)
439 		dev_warn(mmc_dev(host->mmc), "%s: card clock still not gate off in 100us!.\n", __func__);
440 }
441 
442 /* Enable the auto tuning circuit to check the CMD line and BUS line */
443 static inline void usdhc_auto_tuning_mode_sel_and_en(struct sdhci_host *host)
444 {
445 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
446 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
447 	u32 buswidth, auto_tune_buswidth;
448 	u32 reg;
449 
450 	buswidth = USDHC_GET_BUSWIDTH(readl(host->ioaddr + SDHCI_HOST_CONTROL));
451 
452 	switch (buswidth) {
453 	case ESDHC_CTRL_8BITBUS:
454 		auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN;
455 		break;
456 	case ESDHC_CTRL_4BITBUS:
457 		auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN;
458 		break;
459 	default:	/* 1BITBUS */
460 		auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN;
461 		break;
462 	}
463 
464 	/*
465 	 * For USDHC, auto tuning circuit can not handle the async sdio
466 	 * device interrupt correctly. When sdio device use 4 data lines,
467 	 * async sdio interrupt will use the shared DAT[1], if enable auto
468 	 * tuning circuit check these 4 data lines, include the DAT[1],
469 	 * this circuit will detect this interrupt, take this as a data on
470 	 * DAT[1], and adjust the delay cell wrongly.
471 	 * This is the hardware design limitation, to avoid this, for sdio
472 	 * device, config the auto tuning circuit only check DAT[0] and CMD
473 	 * line.
474 	 */
475 	if (imx_data->init_card_type == MMC_TYPE_SDIO)
476 		auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN;
477 
478 	esdhc_clrset_le(host, ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK,
479 			auto_tune_buswidth | ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN,
480 			ESDHC_VEND_SPEC2);
481 
482 	reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
483 	reg |= ESDHC_MIX_CTRL_AUTO_TUNE_EN;
484 	writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
485 }
486 
487 static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
488 {
489 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
490 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
491 	u32 val = readl(host->ioaddr + reg);
492 
493 	if (unlikely(reg == SDHCI_PRESENT_STATE)) {
494 		u32 fsl_prss = val;
495 		/* save the least 20 bits */
496 		val = fsl_prss & 0x000FFFFF;
497 		/* move dat[0-3] bits */
498 		val |= (fsl_prss & 0x0F000000) >> 4;
499 		/* move cmd line bit */
500 		val |= (fsl_prss & 0x00800000) << 1;
501 	}
502 
503 	if (unlikely(reg == SDHCI_CAPABILITIES)) {
504 		/* ignore bit[0-15] as it stores cap_1 register val for mx6sl */
505 		if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
506 			val &= 0xffff0000;
507 
508 		/* In FSL esdhc IC module, only bit20 is used to indicate the
509 		 * ADMA2 capability of esdhc, but this bit is messed up on
510 		 * some SOCs (e.g. on MX25, MX35 this bit is set, but they
511 		 * don't actually support ADMA2). So set the BROKEN_ADMA
512 		 * quirk on MX25/35 platforms.
513 		 */
514 
515 		if (val & SDHCI_CAN_DO_ADMA1) {
516 			val &= ~SDHCI_CAN_DO_ADMA1;
517 			val |= SDHCI_CAN_DO_ADMA2;
518 		}
519 	}
520 
521 	if (unlikely(reg == SDHCI_CAPABILITIES_1)) {
522 		if (esdhc_is_usdhc(imx_data)) {
523 			if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
524 				val = readl(host->ioaddr + SDHCI_CAPABILITIES) & 0xFFFF;
525 			else
526 				/* imx6q/dl does not have cap_1 register, fake one */
527 				val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
528 					| SDHCI_SUPPORT_SDR50
529 					| SDHCI_USE_SDR50_TUNING
530 					| FIELD_PREP(SDHCI_RETUNING_MODE_MASK,
531 						     SDHCI_TUNING_MODE_3);
532 
533 			/*
534 			 * Do not advertise faster UHS modes if there are no
535 			 * pinctrl states for 100MHz/200MHz.
536 			 */
537 			if (IS_ERR_OR_NULL(imx_data->pins_100mhz))
538 				val &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50);
539 			if (IS_ERR_OR_NULL(imx_data->pins_200mhz))
540 				val &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_HS400);
541 		}
542 	}
543 
544 	if (unlikely(reg == SDHCI_MAX_CURRENT) && esdhc_is_usdhc(imx_data)) {
545 		val = 0;
546 		val |= FIELD_PREP(SDHCI_MAX_CURRENT_330_MASK, 0xFF);
547 		val |= FIELD_PREP(SDHCI_MAX_CURRENT_300_MASK, 0xFF);
548 		val |= FIELD_PREP(SDHCI_MAX_CURRENT_180_MASK, 0xFF);
549 	}
550 
551 	if (unlikely(reg == SDHCI_INT_STATUS)) {
552 		if (val & ESDHC_INT_VENDOR_SPEC_DMA_ERR) {
553 			val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR;
554 			val |= SDHCI_INT_ADMA_ERROR;
555 		}
556 
557 		/*
558 		 * mask off the interrupt we get in response to the manually
559 		 * sent CMD12
560 		 */
561 		if ((imx_data->multiblock_status == WAIT_FOR_INT) &&
562 		    ((val & SDHCI_INT_RESPONSE) == SDHCI_INT_RESPONSE)) {
563 			val &= ~SDHCI_INT_RESPONSE;
564 			writel(SDHCI_INT_RESPONSE, host->ioaddr +
565 						   SDHCI_INT_STATUS);
566 			imx_data->multiblock_status = NO_CMD_PENDING;
567 		}
568 	}
569 
570 	return val;
571 }
572 
573 static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
574 {
575 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
576 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
577 	u32 data;
578 
579 	if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE ||
580 			reg == SDHCI_INT_STATUS)) {
581 		if ((val & SDHCI_INT_CARD_INT) && !esdhc_is_usdhc(imx_data)) {
582 			/*
583 			 * Clear and then set D3CD bit to avoid missing the
584 			 * card interrupt. This is an eSDHC controller problem
585 			 * so we need to apply the following workaround: clear
586 			 * and set D3CD bit will make eSDHC re-sample the card
587 			 * interrupt. In case a card interrupt was lost,
588 			 * re-sample it by the following steps.
589 			 */
590 			data = readl(host->ioaddr + SDHCI_HOST_CONTROL);
591 			data &= ~ESDHC_CTRL_D3CD;
592 			writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
593 			data |= ESDHC_CTRL_D3CD;
594 			writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
595 		}
596 
597 		if (val & SDHCI_INT_ADMA_ERROR) {
598 			val &= ~SDHCI_INT_ADMA_ERROR;
599 			val |= ESDHC_INT_VENDOR_SPEC_DMA_ERR;
600 		}
601 	}
602 
603 	if (unlikely((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
604 				&& (reg == SDHCI_INT_STATUS)
605 				&& (val & SDHCI_INT_DATA_END))) {
606 			u32 v;
607 			v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
608 			v &= ~ESDHC_VENDOR_SPEC_SDIO_QUIRK;
609 			writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
610 
611 			if (imx_data->multiblock_status == MULTIBLK_IN_PROCESS)
612 			{
613 				/* send a manual CMD12 with RESPTYP=none */
614 				data = MMC_STOP_TRANSMISSION << 24 |
615 				       SDHCI_CMD_ABORTCMD << 16;
616 				writel(data, host->ioaddr + SDHCI_TRANSFER_MODE);
617 				imx_data->multiblock_status = WAIT_FOR_INT;
618 			}
619 	}
620 
621 	writel(val, host->ioaddr + reg);
622 }
623 
624 static u16 esdhc_readw_le(struct sdhci_host *host, int reg)
625 {
626 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
627 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
628 	u16 ret = 0;
629 	u32 val;
630 
631 	if (unlikely(reg == SDHCI_HOST_VERSION)) {
632 		reg ^= 2;
633 		if (esdhc_is_usdhc(imx_data)) {
634 			/*
635 			 * The usdhc register returns a wrong host version.
636 			 * Correct it here.
637 			 */
638 			return SDHCI_SPEC_300;
639 		}
640 	}
641 
642 	if (unlikely(reg == SDHCI_HOST_CONTROL2)) {
643 		val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
644 		if (val & ESDHC_VENDOR_SPEC_VSELECT)
645 			ret |= SDHCI_CTRL_VDD_180;
646 
647 		if (esdhc_is_usdhc(imx_data)) {
648 			if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
649 				val = readl(host->ioaddr + ESDHC_MIX_CTRL);
650 			else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING)
651 				/* the std tuning bits is in ACMD12_ERR for imx6sl */
652 				val = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
653 		}
654 
655 		if (val & ESDHC_MIX_CTRL_EXE_TUNE)
656 			ret |= SDHCI_CTRL_EXEC_TUNING;
657 		if (val & ESDHC_MIX_CTRL_SMPCLK_SEL)
658 			ret |= SDHCI_CTRL_TUNED_CLK;
659 
660 		ret &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
661 
662 		return ret;
663 	}
664 
665 	if (unlikely(reg == SDHCI_TRANSFER_MODE)) {
666 		if (esdhc_is_usdhc(imx_data)) {
667 			u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
668 			ret = m & ESDHC_MIX_CTRL_SDHCI_MASK;
669 			/* Swap AC23 bit */
670 			if (m & ESDHC_MIX_CTRL_AC23EN) {
671 				ret &= ~ESDHC_MIX_CTRL_AC23EN;
672 				ret |= SDHCI_TRNS_AUTO_CMD23;
673 			}
674 		} else {
675 			ret = readw(host->ioaddr + SDHCI_TRANSFER_MODE);
676 		}
677 
678 		return ret;
679 	}
680 
681 	return readw(host->ioaddr + reg);
682 }
683 
684 static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
685 {
686 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
687 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
688 	u32 new_val = 0;
689 
690 	switch (reg) {
691 	case SDHCI_CLOCK_CONTROL:
692 		new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
693 		if (val & SDHCI_CLOCK_CARD_EN)
694 			new_val |= ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
695 		else
696 			new_val &= ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
697 		writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
698 		if (!(new_val & ESDHC_VENDOR_SPEC_FRC_SDCLK_ON))
699 			esdhc_wait_for_card_clock_gate_off(host);
700 		return;
701 	case SDHCI_HOST_CONTROL2:
702 		new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
703 		if (val & SDHCI_CTRL_VDD_180)
704 			new_val |= ESDHC_VENDOR_SPEC_VSELECT;
705 		else
706 			new_val &= ~ESDHC_VENDOR_SPEC_VSELECT;
707 		writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
708 		if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
709 			u32 v = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
710 			u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
711 			if (val & SDHCI_CTRL_TUNED_CLK) {
712 				v |= ESDHC_MIX_CTRL_SMPCLK_SEL;
713 			} else {
714 				v &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
715 				m &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
716 			}
717 
718 			if (val & SDHCI_CTRL_EXEC_TUNING) {
719 				v |= ESDHC_MIX_CTRL_EXE_TUNE;
720 				m |= ESDHC_MIX_CTRL_FBCLK_SEL;
721 			} else {
722 				v &= ~ESDHC_MIX_CTRL_EXE_TUNE;
723 			}
724 
725 			writel(v, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
726 			writel(m, host->ioaddr + ESDHC_MIX_CTRL);
727 		}
728 		return;
729 	case SDHCI_TRANSFER_MODE:
730 		if ((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
731 				&& (host->cmd->opcode == SD_IO_RW_EXTENDED)
732 				&& (host->cmd->data->blocks > 1)
733 				&& (host->cmd->data->flags & MMC_DATA_READ)) {
734 			u32 v;
735 			v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
736 			v |= ESDHC_VENDOR_SPEC_SDIO_QUIRK;
737 			writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
738 		}
739 
740 		if (esdhc_is_usdhc(imx_data)) {
741 			u32 wml;
742 			u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
743 			/* Swap AC23 bit */
744 			if (val & SDHCI_TRNS_AUTO_CMD23) {
745 				val &= ~SDHCI_TRNS_AUTO_CMD23;
746 				val |= ESDHC_MIX_CTRL_AC23EN;
747 			}
748 			m = val | (m & ~ESDHC_MIX_CTRL_SDHCI_MASK);
749 			writel(m, host->ioaddr + ESDHC_MIX_CTRL);
750 
751 			/* Set watermark levels for PIO access to maximum value
752 			 * (128 words) to accommodate full 512 bytes buffer.
753 			 * For DMA access restore the levels to default value.
754 			 */
755 			m = readl(host->ioaddr + ESDHC_WTMK_LVL);
756 			if (val & SDHCI_TRNS_DMA) {
757 				wml = ESDHC_WTMK_LVL_WML_VAL_DEF;
758 			} else {
759 				u8 ctrl;
760 				wml = ESDHC_WTMK_LVL_WML_VAL_MAX;
761 
762 				/*
763 				 * Since already disable DMA mode, so also need
764 				 * to clear the DMASEL. Otherwise, for standard
765 				 * tuning, when send tuning command, usdhc will
766 				 * still prefetch the ADMA script from wrong
767 				 * DMA address, then we will see IOMMU report
768 				 * some error which show lack of TLB mapping.
769 				 */
770 				ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
771 				ctrl &= ~SDHCI_CTRL_DMA_MASK;
772 				sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
773 			}
774 			m &= ~(ESDHC_WTMK_LVL_RD_WML_MASK |
775 			       ESDHC_WTMK_LVL_WR_WML_MASK);
776 			m |= (wml << ESDHC_WTMK_LVL_RD_WML_SHIFT) |
777 			     (wml << ESDHC_WTMK_LVL_WR_WML_SHIFT);
778 			writel(m, host->ioaddr + ESDHC_WTMK_LVL);
779 		} else {
780 			/*
781 			 * Postpone this write, we must do it together with a
782 			 * command write that is down below.
783 			 */
784 			imx_data->scratchpad = val;
785 		}
786 		return;
787 	case SDHCI_COMMAND:
788 		if (host->cmd->opcode == MMC_STOP_TRANSMISSION)
789 			val |= SDHCI_CMD_ABORTCMD;
790 
791 		if ((host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
792 		    (imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
793 			imx_data->multiblock_status = MULTIBLK_IN_PROCESS;
794 
795 		if (esdhc_is_usdhc(imx_data))
796 			writel(val << 16,
797 			       host->ioaddr + SDHCI_TRANSFER_MODE);
798 		else
799 			writel(val << 16 | imx_data->scratchpad,
800 			       host->ioaddr + SDHCI_TRANSFER_MODE);
801 		return;
802 	case SDHCI_BLOCK_SIZE:
803 		val &= ~SDHCI_MAKE_BLKSZ(0x7, 0);
804 		break;
805 	}
806 	esdhc_clrset_le(host, 0xffff, val, reg);
807 }
808 
809 static u8 esdhc_readb_le(struct sdhci_host *host, int reg)
810 {
811 	u8 ret;
812 	u32 val;
813 
814 	switch (reg) {
815 	case SDHCI_HOST_CONTROL:
816 		val = readl(host->ioaddr + reg);
817 
818 		ret = val & SDHCI_CTRL_LED;
819 		ret |= (val >> 5) & SDHCI_CTRL_DMA_MASK;
820 		ret |= (val & ESDHC_CTRL_4BITBUS);
821 		ret |= (val & ESDHC_CTRL_8BITBUS) << 3;
822 		return ret;
823 	}
824 
825 	return readb(host->ioaddr + reg);
826 }
827 
828 static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg)
829 {
830 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
831 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
832 	u32 new_val = 0;
833 	u32 mask;
834 
835 	switch (reg) {
836 	case SDHCI_POWER_CONTROL:
837 		/*
838 		 * FSL put some DMA bits here
839 		 * If your board has a regulator, code should be here
840 		 */
841 		return;
842 	case SDHCI_HOST_CONTROL:
843 		/* FSL messed up here, so we need to manually compose it. */
844 		new_val = val & SDHCI_CTRL_LED;
845 		/* ensure the endianness */
846 		new_val |= ESDHC_HOST_CONTROL_LE;
847 		/* bits 8&9 are reserved on mx25 */
848 		if (!is_imx25_esdhc(imx_data)) {
849 			/* DMA mode bits are shifted */
850 			new_val |= (val & SDHCI_CTRL_DMA_MASK) << 5;
851 		}
852 
853 		/*
854 		 * Do not touch buswidth bits here. This is done in
855 		 * esdhc_pltfm_bus_width.
856 		 * Do not touch the D3CD bit either which is used for the
857 		 * SDIO interrupt erratum workaround.
858 		 */
859 		mask = 0xffff & ~(ESDHC_CTRL_BUSWIDTH_MASK | ESDHC_CTRL_D3CD);
860 
861 		esdhc_clrset_le(host, mask, new_val, reg);
862 		return;
863 	case SDHCI_SOFTWARE_RESET:
864 		if (val & SDHCI_RESET_DATA)
865 			new_val = readl(host->ioaddr + SDHCI_HOST_CONTROL);
866 		break;
867 	}
868 	esdhc_clrset_le(host, 0xff, val, reg);
869 
870 	if (reg == SDHCI_SOFTWARE_RESET) {
871 		if (val & SDHCI_RESET_ALL) {
872 			/*
873 			 * The esdhc has a design violation to SDHC spec which
874 			 * tells that software reset should not affect card
875 			 * detection circuit. But esdhc clears its SYSCTL
876 			 * register bits [0..2] during the software reset. This
877 			 * will stop those clocks that card detection circuit
878 			 * relies on. To work around it, we turn the clocks on
879 			 * back to keep card detection circuit functional.
880 			 */
881 			esdhc_clrset_le(host, 0x7, 0x7, ESDHC_SYSTEM_CONTROL);
882 			/*
883 			 * The reset on usdhc fails to clear MIX_CTRL register.
884 			 * Do it manually here.
885 			 */
886 			if (esdhc_is_usdhc(imx_data)) {
887 				/*
888 				 * the tuning bits should be kept during reset
889 				 */
890 				new_val = readl(host->ioaddr + ESDHC_MIX_CTRL);
891 				writel(new_val & ESDHC_MIX_CTRL_TUNING_MASK,
892 						host->ioaddr + ESDHC_MIX_CTRL);
893 				imx_data->is_ddr = 0;
894 			}
895 		} else if (val & SDHCI_RESET_DATA) {
896 			/*
897 			 * The eSDHC DAT line software reset clears at least the
898 			 * data transfer width on i.MX25, so make sure that the
899 			 * Host Control register is unaffected.
900 			 */
901 			esdhc_clrset_le(host, 0xff, new_val,
902 					SDHCI_HOST_CONTROL);
903 		}
904 	}
905 }
906 
907 static unsigned int esdhc_pltfm_get_max_clock(struct sdhci_host *host)
908 {
909 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
910 
911 	return pltfm_host->clock;
912 }
913 
914 static unsigned int esdhc_pltfm_get_min_clock(struct sdhci_host *host)
915 {
916 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
917 
918 	return pltfm_host->clock / 256 / 16;
919 }
920 
921 static inline void esdhc_pltfm_set_clock(struct sdhci_host *host,
922 					 unsigned int clock)
923 {
924 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
925 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
926 	unsigned int host_clock = pltfm_host->clock;
927 	int ddr_pre_div = imx_data->is_ddr ? 2 : 1;
928 	int pre_div = 1;
929 	int div = 1;
930 	int ret;
931 	u32 temp, val;
932 
933 	if (esdhc_is_usdhc(imx_data)) {
934 		val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
935 		writel(val & ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
936 			host->ioaddr + ESDHC_VENDOR_SPEC);
937 		esdhc_wait_for_card_clock_gate_off(host);
938 	}
939 
940 	if (clock == 0) {
941 		host->mmc->actual_clock = 0;
942 		return;
943 	}
944 
945 	/* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */
946 	if (is_imx53_esdhc(imx_data)) {
947 		/*
948 		 * According to the i.MX53 reference manual, if DLLCTRL[10] can
949 		 * be set, then the controller is eSDHCv3, else it is eSDHCv2.
950 		 */
951 		val = readl(host->ioaddr + ESDHC_DLL_CTRL);
952 		writel(val | BIT(10), host->ioaddr + ESDHC_DLL_CTRL);
953 		temp = readl(host->ioaddr + ESDHC_DLL_CTRL);
954 		writel(val, host->ioaddr + ESDHC_DLL_CTRL);
955 		if (temp & BIT(10))
956 			pre_div = 2;
957 	}
958 
959 	temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
960 	temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
961 		| ESDHC_CLOCK_MASK);
962 	sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
963 
964 	if (imx_data->socdata->flags & ESDHC_FLAG_ERR010450) {
965 		unsigned int max_clock;
966 
967 		max_clock = imx_data->is_ddr ? 45000000 : 150000000;
968 
969 		clock = min(clock, max_clock);
970 	}
971 
972 	while (host_clock / (16 * pre_div * ddr_pre_div) > clock &&
973 			pre_div < 256)
974 		pre_div *= 2;
975 
976 	while (host_clock / (div * pre_div * ddr_pre_div) > clock && div < 16)
977 		div++;
978 
979 	host->mmc->actual_clock = host_clock / (div * pre_div * ddr_pre_div);
980 	dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n",
981 		clock, host->mmc->actual_clock);
982 
983 	pre_div >>= 1;
984 	div--;
985 
986 	temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
987 	temp |= (ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
988 		| (div << ESDHC_DIVIDER_SHIFT)
989 		| (pre_div << ESDHC_PREDIV_SHIFT));
990 	sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
991 
992 	/* need to wait the bit 3 of the PRSSTAT to be set, make sure card clock is stable */
993 	ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, temp,
994 				(temp & ESDHC_CLOCK_STABLE), 2, 100);
995 	if (ret == -ETIMEDOUT)
996 		dev_warn(mmc_dev(host->mmc), "card clock still not stable in 100us!.\n");
997 
998 	if (esdhc_is_usdhc(imx_data)) {
999 		val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
1000 		writel(val | ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
1001 			host->ioaddr + ESDHC_VENDOR_SPEC);
1002 	}
1003 
1004 }
1005 
1006 static unsigned int esdhc_pltfm_get_ro(struct sdhci_host *host)
1007 {
1008 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1009 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1010 	struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1011 
1012 	switch (boarddata->wp_type) {
1013 	case ESDHC_WP_GPIO:
1014 		return mmc_gpio_get_ro(host->mmc);
1015 	case ESDHC_WP_CONTROLLER:
1016 		return !(readl(host->ioaddr + SDHCI_PRESENT_STATE) &
1017 			       SDHCI_WRITE_PROTECT);
1018 	case ESDHC_WP_NONE:
1019 		break;
1020 	}
1021 
1022 	return -ENOSYS;
1023 }
1024 
1025 static void esdhc_pltfm_set_bus_width(struct sdhci_host *host, int width)
1026 {
1027 	u32 ctrl;
1028 
1029 	switch (width) {
1030 	case MMC_BUS_WIDTH_8:
1031 		ctrl = ESDHC_CTRL_8BITBUS;
1032 		break;
1033 	case MMC_BUS_WIDTH_4:
1034 		ctrl = ESDHC_CTRL_4BITBUS;
1035 		break;
1036 	default:
1037 		ctrl = 0;
1038 		break;
1039 	}
1040 
1041 	esdhc_clrset_le(host, ESDHC_CTRL_BUSWIDTH_MASK, ctrl,
1042 			SDHCI_HOST_CONTROL);
1043 }
1044 
1045 static void esdhc_reset_tuning(struct sdhci_host *host)
1046 {
1047 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1048 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1049 	u32 ctrl;
1050 	int ret;
1051 
1052 	/* Reset the tuning circuit */
1053 	if (esdhc_is_usdhc(imx_data)) {
1054 		ctrl = readl(host->ioaddr + ESDHC_MIX_CTRL);
1055 		ctrl &= ~ESDHC_MIX_CTRL_AUTO_TUNE_EN;
1056 		if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
1057 			ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
1058 			ctrl &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
1059 			writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL);
1060 			writel(0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1061 		} else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
1062 			writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL);
1063 			ctrl = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1064 			ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
1065 			ctrl &= ~ESDHC_MIX_CTRL_EXE_TUNE;
1066 			writel(ctrl, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1067 			/* Make sure ESDHC_MIX_CTRL_EXE_TUNE cleared */
1068 			ret = readl_poll_timeout(host->ioaddr + SDHCI_AUTO_CMD_STATUS,
1069 				ctrl, !(ctrl & ESDHC_MIX_CTRL_EXE_TUNE), 1, 50);
1070 			if (ret == -ETIMEDOUT)
1071 				dev_warn(mmc_dev(host->mmc),
1072 				 "Warning! clear execute tuning bit failed\n");
1073 			/*
1074 			 * SDHCI_INT_DATA_AVAIL is W1C bit, set this bit will clear the
1075 			 * usdhc IP internal logic flag execute_tuning_with_clr_buf, which
1076 			 * will finally make sure the normal data transfer logic correct.
1077 			 */
1078 			ctrl = readl(host->ioaddr + SDHCI_INT_STATUS);
1079 			ctrl |= SDHCI_INT_DATA_AVAIL;
1080 			writel(ctrl, host->ioaddr + SDHCI_INT_STATUS);
1081 		}
1082 	}
1083 }
1084 
1085 static void usdhc_init_card(struct mmc_host *mmc, struct mmc_card *card)
1086 {
1087 	struct sdhci_host *host = mmc_priv(mmc);
1088 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1089 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1090 
1091 	imx_data->init_card_type = card->type;
1092 }
1093 
1094 static int usdhc_execute_tuning(struct mmc_host *mmc, u32 opcode)
1095 {
1096 	struct sdhci_host *host = mmc_priv(mmc);
1097 	int err;
1098 
1099 	/*
1100 	 * i.MX uSDHC internally already uses a fixed optimized timing for
1101 	 * DDR50, normally does not require tuning for DDR50 mode.
1102 	 */
1103 	if (host->timing == MMC_TIMING_UHS_DDR50)
1104 		return 0;
1105 
1106 	/*
1107 	 * Reset tuning circuit logic. If not, the previous tuning result
1108 	 * will impact current tuning, make current tuning can't set the
1109 	 * correct delay cell.
1110 	 */
1111 	esdhc_reset_tuning(host);
1112 	err = sdhci_execute_tuning(mmc, opcode);
1113 	/* If tuning done, enable auto tuning */
1114 	if (!err && !host->tuning_err)
1115 		usdhc_auto_tuning_mode_sel_and_en(host);
1116 
1117 	return err;
1118 }
1119 
1120 static void esdhc_prepare_tuning(struct sdhci_host *host, u32 val)
1121 {
1122 	u32 reg;
1123 	u8 sw_rst;
1124 	int ret;
1125 
1126 	/* FIXME: delay a bit for card to be ready for next tuning due to errors */
1127 	mdelay(1);
1128 
1129 	/* IC suggest to reset USDHC before every tuning command */
1130 	esdhc_clrset_le(host, 0xff, SDHCI_RESET_ALL, SDHCI_SOFTWARE_RESET);
1131 	ret = readb_poll_timeout(host->ioaddr + SDHCI_SOFTWARE_RESET, sw_rst,
1132 				!(sw_rst & SDHCI_RESET_ALL), 10, 100);
1133 	if (ret == -ETIMEDOUT)
1134 		dev_warn(mmc_dev(host->mmc),
1135 		"warning! RESET_ALL never complete before sending tuning command\n");
1136 
1137 	reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
1138 	reg |= ESDHC_MIX_CTRL_EXE_TUNE | ESDHC_MIX_CTRL_SMPCLK_SEL |
1139 			ESDHC_MIX_CTRL_FBCLK_SEL;
1140 	writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
1141 	writel(val << 8, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1142 	dev_dbg(mmc_dev(host->mmc),
1143 		"tuning with delay 0x%x ESDHC_TUNE_CTRL_STATUS 0x%x\n",
1144 			val, readl(host->ioaddr + ESDHC_TUNE_CTRL_STATUS));
1145 }
1146 
1147 static void esdhc_post_tuning(struct sdhci_host *host)
1148 {
1149 	u32 reg;
1150 
1151 	reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
1152 	reg &= ~ESDHC_MIX_CTRL_EXE_TUNE;
1153 	writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
1154 }
1155 
1156 static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode)
1157 {
1158 	int min, max, avg, ret;
1159 
1160 	/* find the mininum delay first which can pass tuning */
1161 	min = ESDHC_TUNE_CTRL_MIN;
1162 	while (min < ESDHC_TUNE_CTRL_MAX) {
1163 		esdhc_prepare_tuning(host, min);
1164 		if (!mmc_send_tuning(host->mmc, opcode, NULL))
1165 			break;
1166 		min += ESDHC_TUNE_CTRL_STEP;
1167 	}
1168 
1169 	/* find the maxinum delay which can not pass tuning */
1170 	max = min + ESDHC_TUNE_CTRL_STEP;
1171 	while (max < ESDHC_TUNE_CTRL_MAX) {
1172 		esdhc_prepare_tuning(host, max);
1173 		if (mmc_send_tuning(host->mmc, opcode, NULL)) {
1174 			max -= ESDHC_TUNE_CTRL_STEP;
1175 			break;
1176 		}
1177 		max += ESDHC_TUNE_CTRL_STEP;
1178 	}
1179 
1180 	/* use average delay to get the best timing */
1181 	avg = (min + max) / 2;
1182 	esdhc_prepare_tuning(host, avg);
1183 	ret = mmc_send_tuning(host->mmc, opcode, NULL);
1184 	esdhc_post_tuning(host);
1185 
1186 	dev_dbg(mmc_dev(host->mmc), "tuning %s at 0x%x ret %d\n",
1187 		ret ? "failed" : "passed", avg, ret);
1188 
1189 	return ret;
1190 }
1191 
1192 static void esdhc_hs400_enhanced_strobe(struct mmc_host *mmc, struct mmc_ios *ios)
1193 {
1194 	struct sdhci_host *host = mmc_priv(mmc);
1195 	u32 m;
1196 
1197 	m = readl(host->ioaddr + ESDHC_MIX_CTRL);
1198 	if (ios->enhanced_strobe)
1199 		m |= ESDHC_MIX_CTRL_HS400_ES_EN;
1200 	else
1201 		m &= ~ESDHC_MIX_CTRL_HS400_ES_EN;
1202 	writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1203 }
1204 
1205 static int esdhc_change_pinstate(struct sdhci_host *host,
1206 						unsigned int uhs)
1207 {
1208 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1209 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1210 	struct pinctrl_state *pinctrl;
1211 
1212 	dev_dbg(mmc_dev(host->mmc), "change pinctrl state for uhs %d\n", uhs);
1213 
1214 	if (IS_ERR(imx_data->pinctrl) ||
1215 		IS_ERR(imx_data->pins_100mhz) ||
1216 		IS_ERR(imx_data->pins_200mhz))
1217 		return -EINVAL;
1218 
1219 	switch (uhs) {
1220 	case MMC_TIMING_UHS_SDR50:
1221 	case MMC_TIMING_UHS_DDR50:
1222 		pinctrl = imx_data->pins_100mhz;
1223 		break;
1224 	case MMC_TIMING_UHS_SDR104:
1225 	case MMC_TIMING_MMC_HS200:
1226 	case MMC_TIMING_MMC_HS400:
1227 		pinctrl = imx_data->pins_200mhz;
1228 		break;
1229 	default:
1230 		/* back to default state for other legacy timing */
1231 		return pinctrl_select_default_state(mmc_dev(host->mmc));
1232 	}
1233 
1234 	return pinctrl_select_state(imx_data->pinctrl, pinctrl);
1235 }
1236 
1237 /*
1238  * For HS400 eMMC, there is a data_strobe line. This signal is generated
1239  * by the device and used for data output and CRC status response output
1240  * in HS400 mode. The frequency of this signal follows the frequency of
1241  * CLK generated by host. The host receives the data which is aligned to the
1242  * edge of data_strobe line. Due to the time delay between CLK line and
1243  * data_strobe line, if the delay time is larger than one clock cycle,
1244  * then CLK and data_strobe line will be misaligned, read error shows up.
1245  */
1246 static void esdhc_set_strobe_dll(struct sdhci_host *host)
1247 {
1248 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1249 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1250 	u32 strobe_delay;
1251 	u32 v;
1252 	int ret;
1253 
1254 	/* disable clock before enabling strobe dll */
1255 	writel(readl(host->ioaddr + ESDHC_VENDOR_SPEC) &
1256 		~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
1257 		host->ioaddr + ESDHC_VENDOR_SPEC);
1258 	esdhc_wait_for_card_clock_gate_off(host);
1259 
1260 	/* force a reset on strobe dll */
1261 	writel(ESDHC_STROBE_DLL_CTRL_RESET,
1262 		host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1263 	/* clear the reset bit on strobe dll before any setting */
1264 	writel(0, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1265 
1266 	/*
1267 	 * enable strobe dll ctrl and adjust the delay target
1268 	 * for the uSDHC loopback read clock
1269 	 */
1270 	if (imx_data->boarddata.strobe_dll_delay_target)
1271 		strobe_delay = imx_data->boarddata.strobe_dll_delay_target;
1272 	else
1273 		strobe_delay = ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT;
1274 	v = ESDHC_STROBE_DLL_CTRL_ENABLE |
1275 		ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT |
1276 		(strobe_delay << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
1277 	writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1278 
1279 	/* wait max 50us to get the REF/SLV lock */
1280 	ret = readl_poll_timeout(host->ioaddr + ESDHC_STROBE_DLL_STATUS, v,
1281 		((v & ESDHC_STROBE_DLL_STS_REF_LOCK) && (v & ESDHC_STROBE_DLL_STS_SLV_LOCK)), 1, 50);
1282 	if (ret == -ETIMEDOUT)
1283 		dev_warn(mmc_dev(host->mmc),
1284 		"warning! HS400 strobe DLL status REF/SLV not lock in 50us, STROBE DLL status is %x!\n", v);
1285 }
1286 
1287 static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
1288 {
1289 	u32 m;
1290 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1291 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1292 	struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1293 
1294 	/* disable ddr mode and disable HS400 mode */
1295 	m = readl(host->ioaddr + ESDHC_MIX_CTRL);
1296 	m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN);
1297 	imx_data->is_ddr = 0;
1298 
1299 	switch (timing) {
1300 	case MMC_TIMING_UHS_SDR12:
1301 	case MMC_TIMING_UHS_SDR25:
1302 	case MMC_TIMING_UHS_SDR50:
1303 	case MMC_TIMING_UHS_SDR104:
1304 	case MMC_TIMING_MMC_HS:
1305 	case MMC_TIMING_MMC_HS200:
1306 		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1307 		break;
1308 	case MMC_TIMING_UHS_DDR50:
1309 	case MMC_TIMING_MMC_DDR52:
1310 		m |= ESDHC_MIX_CTRL_DDREN;
1311 		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1312 		imx_data->is_ddr = 1;
1313 		if (boarddata->delay_line) {
1314 			u32 v;
1315 			v = boarddata->delay_line <<
1316 				ESDHC_DLL_OVERRIDE_VAL_SHIFT |
1317 				(1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
1318 			if (is_imx53_esdhc(imx_data))
1319 				v <<= 1;
1320 			writel(v, host->ioaddr + ESDHC_DLL_CTRL);
1321 		}
1322 		break;
1323 	case MMC_TIMING_MMC_HS400:
1324 		m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
1325 		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1326 		imx_data->is_ddr = 1;
1327 		/* update clock after enable DDR for strobe DLL lock */
1328 		host->ops->set_clock(host, host->clock);
1329 		esdhc_set_strobe_dll(host);
1330 		break;
1331 	case MMC_TIMING_LEGACY:
1332 	default:
1333 		esdhc_reset_tuning(host);
1334 		break;
1335 	}
1336 
1337 	esdhc_change_pinstate(host, timing);
1338 }
1339 
1340 static void esdhc_reset(struct sdhci_host *host, u8 mask)
1341 {
1342 	sdhci_and_cqhci_reset(host, mask);
1343 
1344 	sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
1345 	sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
1346 }
1347 
1348 static unsigned int esdhc_get_max_timeout_count(struct sdhci_host *host)
1349 {
1350 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1351 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1352 
1353 	/* Doc Erratum: the uSDHC actual maximum timeout count is 1 << 29 */
1354 	return esdhc_is_usdhc(imx_data) ? 1 << 29 : 1 << 27;
1355 }
1356 
1357 static void esdhc_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
1358 {
1359 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1360 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1361 
1362 	/* use maximum timeout counter */
1363 	esdhc_clrset_le(host, ESDHC_SYS_CTRL_DTOCV_MASK,
1364 			esdhc_is_usdhc(imx_data) ? 0xF : 0xE,
1365 			SDHCI_TIMEOUT_CONTROL);
1366 }
1367 
1368 static u32 esdhc_cqhci_irq(struct sdhci_host *host, u32 intmask)
1369 {
1370 	int cmd_error = 0;
1371 	int data_error = 0;
1372 
1373 	if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
1374 		return intmask;
1375 
1376 	cqhci_irq(host->mmc, intmask, cmd_error, data_error);
1377 
1378 	return 0;
1379 }
1380 
1381 static struct sdhci_ops sdhci_esdhc_ops = {
1382 	.read_l = esdhc_readl_le,
1383 	.read_w = esdhc_readw_le,
1384 	.read_b = esdhc_readb_le,
1385 	.write_l = esdhc_writel_le,
1386 	.write_w = esdhc_writew_le,
1387 	.write_b = esdhc_writeb_le,
1388 	.set_clock = esdhc_pltfm_set_clock,
1389 	.get_max_clock = esdhc_pltfm_get_max_clock,
1390 	.get_min_clock = esdhc_pltfm_get_min_clock,
1391 	.get_max_timeout_count = esdhc_get_max_timeout_count,
1392 	.get_ro = esdhc_pltfm_get_ro,
1393 	.set_timeout = esdhc_set_timeout,
1394 	.set_bus_width = esdhc_pltfm_set_bus_width,
1395 	.set_uhs_signaling = esdhc_set_uhs_signaling,
1396 	.reset = esdhc_reset,
1397 	.irq = esdhc_cqhci_irq,
1398 	.dump_vendor_regs = esdhc_dump_debug_regs,
1399 };
1400 
1401 static const struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = {
1402 	.quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT
1403 			| SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
1404 			| SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC
1405 			| SDHCI_QUIRK_BROKEN_CARD_DETECTION,
1406 	.ops = &sdhci_esdhc_ops,
1407 };
1408 
1409 static void sdhci_esdhc_imx_hwinit(struct sdhci_host *host)
1410 {
1411 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1412 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1413 	struct cqhci_host *cq_host = host->mmc->cqe_private;
1414 	u32 tmp;
1415 
1416 	if (esdhc_is_usdhc(imx_data)) {
1417 		/*
1418 		 * The imx6q ROM code will change the default watermark
1419 		 * level setting to something insane.  Change it back here.
1420 		 */
1421 		writel(ESDHC_WTMK_DEFAULT_VAL, host->ioaddr + ESDHC_WTMK_LVL);
1422 
1423 		/*
1424 		 * ROM code will change the bit burst_length_enable setting
1425 		 * to zero if this usdhc is chosen to boot system. Change
1426 		 * it back here, otherwise it will impact the performance a
1427 		 * lot. This bit is used to enable/disable the burst length
1428 		 * for the external AHB2AXI bridge. It's useful especially
1429 		 * for INCR transfer because without burst length indicator,
1430 		 * the AHB2AXI bridge does not know the burst length in
1431 		 * advance. And without burst length indicator, AHB INCR
1432 		 * transfer can only be converted to singles on the AXI side.
1433 		 */
1434 		writel(readl(host->ioaddr + SDHCI_HOST_CONTROL)
1435 			| ESDHC_BURST_LEN_EN_INCR,
1436 			host->ioaddr + SDHCI_HOST_CONTROL);
1437 
1438 		/*
1439 		 * erratum ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL
1440 		 * TO1.1, it's harmless for MX6SL
1441 		 */
1442 		if (!(imx_data->socdata->flags & ESDHC_FLAG_SKIP_ERR004536)) {
1443 			writel(readl(host->ioaddr + 0x6c) & ~BIT(7),
1444 				host->ioaddr + 0x6c);
1445 		}
1446 
1447 		/* disable DLL_CTRL delay line settings */
1448 		writel(0x0, host->ioaddr + ESDHC_DLL_CTRL);
1449 
1450 		/*
1451 		 * For the case of command with busy, if set the bit
1452 		 * ESDHC_VEND_SPEC2_EN_BUSY_IRQ, USDHC will generate a
1453 		 * transfer complete interrupt when busy is deasserted.
1454 		 * When CQHCI use DCMD to send a CMD need R1b respons,
1455 		 * CQHCI require to set ESDHC_VEND_SPEC2_EN_BUSY_IRQ,
1456 		 * otherwise DCMD will always meet timeout waiting for
1457 		 * hardware interrupt issue.
1458 		 */
1459 		if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) {
1460 			tmp = readl(host->ioaddr + ESDHC_VEND_SPEC2);
1461 			tmp |= ESDHC_VEND_SPEC2_EN_BUSY_IRQ;
1462 			writel(tmp, host->ioaddr + ESDHC_VEND_SPEC2);
1463 
1464 			host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
1465 		}
1466 
1467 		if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
1468 			tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
1469 			tmp |= ESDHC_STD_TUNING_EN;
1470 
1471 			/*
1472 			 * ROM code or bootloader may config the start tap
1473 			 * and step, unmask them first.
1474 			 */
1475 			tmp &= ~(ESDHC_TUNING_START_TAP_MASK | ESDHC_TUNING_STEP_MASK);
1476 			if (imx_data->boarddata.tuning_start_tap)
1477 				tmp |= imx_data->boarddata.tuning_start_tap;
1478 			else
1479 				tmp |= ESDHC_TUNING_START_TAP_DEFAULT;
1480 
1481 			if (imx_data->boarddata.tuning_step) {
1482 				tmp |= imx_data->boarddata.tuning_step
1483 					<< ESDHC_TUNING_STEP_SHIFT;
1484 			} else {
1485 				tmp |= ESDHC_TUNING_STEP_DEFAULT
1486 					<< ESDHC_TUNING_STEP_SHIFT;
1487 			}
1488 
1489 			/* Disable the CMD CRC check for tuning, if not, need to
1490 			 * add some delay after every tuning command, because
1491 			 * hardware standard tuning logic will directly go to next
1492 			 * step once it detect the CMD CRC error, will not wait for
1493 			 * the card side to finally send out the tuning data, trigger
1494 			 * the buffer read ready interrupt immediately. If usdhc send
1495 			 * the next tuning command some eMMC card will stuck, can't
1496 			 * response, block the tuning procedure or the first command
1497 			 * after the whole tuning procedure always can't get any response.
1498 			 */
1499 			tmp |= ESDHC_TUNING_CMD_CRC_CHECK_DISABLE;
1500 			writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL);
1501 		} else if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
1502 			/*
1503 			 * ESDHC_STD_TUNING_EN may be configed in bootloader
1504 			 * or ROM code, so clear this bit here to make sure
1505 			 * the manual tuning can work.
1506 			 */
1507 			tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
1508 			tmp &= ~ESDHC_STD_TUNING_EN;
1509 			writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL);
1510 		}
1511 
1512 		/*
1513 		 * On i.MX8MM, we are running Dual Linux OS, with 1st Linux using SD Card
1514 		 * as rootfs storage, 2nd Linux using eMMC as rootfs storage. We let
1515 		 * the 1st linux configure power/clock for the 2nd Linux.
1516 		 *
1517 		 * When the 2nd Linux is booting into rootfs stage, we let the 1st Linux
1518 		 * to destroy the 2nd linux, then restart the 2nd linux, we met SDHCI dump.
1519 		 * After we clear the pending interrupt and halt CQCTL, issue gone.
1520 		 */
1521 		if (cq_host) {
1522 			tmp = cqhci_readl(cq_host, CQHCI_IS);
1523 			cqhci_writel(cq_host, tmp, CQHCI_IS);
1524 			cqhci_writel(cq_host, CQHCI_HALT, CQHCI_CTL);
1525 		}
1526 	}
1527 }
1528 
1529 static void esdhc_cqe_enable(struct mmc_host *mmc)
1530 {
1531 	struct sdhci_host *host = mmc_priv(mmc);
1532 	struct cqhci_host *cq_host = mmc->cqe_private;
1533 	u32 reg;
1534 	u16 mode;
1535 	int count = 10;
1536 
1537 	/*
1538 	 * CQE gets stuck if it sees Buffer Read Enable bit set, which can be
1539 	 * the case after tuning, so ensure the buffer is drained.
1540 	 */
1541 	reg = sdhci_readl(host, SDHCI_PRESENT_STATE);
1542 	while (reg & SDHCI_DATA_AVAILABLE) {
1543 		sdhci_readl(host, SDHCI_BUFFER);
1544 		reg = sdhci_readl(host, SDHCI_PRESENT_STATE);
1545 		if (count-- == 0) {
1546 			dev_warn(mmc_dev(host->mmc),
1547 				"CQE may get stuck because the Buffer Read Enable bit is set\n");
1548 			break;
1549 		}
1550 		mdelay(1);
1551 	}
1552 
1553 	/*
1554 	 * Runtime resume will reset the entire host controller, which
1555 	 * will also clear the DMAEN/BCEN of register ESDHC_MIX_CTRL.
1556 	 * Here set DMAEN and BCEN when enable CMDQ.
1557 	 */
1558 	mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
1559 	if (host->flags & SDHCI_REQ_USE_DMA)
1560 		mode |= SDHCI_TRNS_DMA;
1561 	if (!(host->quirks2 & SDHCI_QUIRK2_SUPPORT_SINGLE))
1562 		mode |= SDHCI_TRNS_BLK_CNT_EN;
1563 	sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
1564 
1565 	/*
1566 	 * Though Runtime resume reset the entire host controller,
1567 	 * but do not impact the CQHCI side, need to clear the
1568 	 * HALT bit, avoid CQHCI stuck in the first request when
1569 	 * system resume back.
1570 	 */
1571 	cqhci_writel(cq_host, 0, CQHCI_CTL);
1572 	if (cqhci_readl(cq_host, CQHCI_CTL) & CQHCI_HALT)
1573 		dev_err(mmc_dev(host->mmc),
1574 			"failed to exit halt state when enable CQE\n");
1575 
1576 
1577 	sdhci_cqe_enable(mmc);
1578 }
1579 
1580 static void esdhc_sdhci_dumpregs(struct mmc_host *mmc)
1581 {
1582 	sdhci_dumpregs(mmc_priv(mmc));
1583 }
1584 
1585 static const struct cqhci_host_ops esdhc_cqhci_ops = {
1586 	.enable		= esdhc_cqe_enable,
1587 	.disable	= sdhci_cqe_disable,
1588 	.dumpregs	= esdhc_sdhci_dumpregs,
1589 };
1590 
1591 static int
1592 sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
1593 			 struct sdhci_host *host,
1594 			 struct pltfm_imx_data *imx_data)
1595 {
1596 	struct device_node *np = pdev->dev.of_node;
1597 	struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1598 	int ret;
1599 
1600 	if (of_property_read_bool(np, "fsl,wp-controller"))
1601 		boarddata->wp_type = ESDHC_WP_CONTROLLER;
1602 
1603 	/*
1604 	 * If we have this property, then activate WP check.
1605 	 * Retrieveing and requesting the actual WP GPIO will happen
1606 	 * in the call to mmc_of_parse().
1607 	 */
1608 	if (of_property_read_bool(np, "wp-gpios"))
1609 		boarddata->wp_type = ESDHC_WP_GPIO;
1610 
1611 	of_property_read_u32(np, "fsl,tuning-step", &boarddata->tuning_step);
1612 	of_property_read_u32(np, "fsl,tuning-start-tap",
1613 			     &boarddata->tuning_start_tap);
1614 
1615 	of_property_read_u32(np, "fsl,strobe-dll-delay-target",
1616 				&boarddata->strobe_dll_delay_target);
1617 	if (of_property_read_bool(np, "no-1-8-v"))
1618 		host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
1619 
1620 	if (of_property_read_u32(np, "fsl,delay-line", &boarddata->delay_line))
1621 		boarddata->delay_line = 0;
1622 
1623 	mmc_of_parse_voltage(host->mmc, &host->ocr_mask);
1624 
1625 	if (esdhc_is_usdhc(imx_data) && !IS_ERR(imx_data->pinctrl)) {
1626 		imx_data->pins_100mhz = pinctrl_lookup_state(imx_data->pinctrl,
1627 						ESDHC_PINCTRL_STATE_100MHZ);
1628 		imx_data->pins_200mhz = pinctrl_lookup_state(imx_data->pinctrl,
1629 						ESDHC_PINCTRL_STATE_200MHZ);
1630 	}
1631 
1632 	/* call to generic mmc_of_parse to support additional capabilities */
1633 	ret = mmc_of_parse(host->mmc);
1634 	if (ret)
1635 		return ret;
1636 
1637 	if (mmc_gpio_get_cd(host->mmc) >= 0)
1638 		host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
1639 
1640 	return 0;
1641 }
1642 
1643 static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
1644 {
1645 	struct sdhci_pltfm_host *pltfm_host;
1646 	struct sdhci_host *host;
1647 	struct cqhci_host *cq_host;
1648 	int err;
1649 	struct pltfm_imx_data *imx_data;
1650 
1651 	host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata,
1652 				sizeof(*imx_data));
1653 	if (IS_ERR(host))
1654 		return PTR_ERR(host);
1655 
1656 	pltfm_host = sdhci_priv(host);
1657 
1658 	imx_data = sdhci_pltfm_priv(pltfm_host);
1659 
1660 	imx_data->socdata = device_get_match_data(&pdev->dev);
1661 
1662 	if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1663 		cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0);
1664 
1665 	imx_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
1666 	if (IS_ERR(imx_data->clk_ipg)) {
1667 		err = PTR_ERR(imx_data->clk_ipg);
1668 		goto free_sdhci;
1669 	}
1670 
1671 	imx_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb");
1672 	if (IS_ERR(imx_data->clk_ahb)) {
1673 		err = PTR_ERR(imx_data->clk_ahb);
1674 		goto free_sdhci;
1675 	}
1676 
1677 	imx_data->clk_per = devm_clk_get(&pdev->dev, "per");
1678 	if (IS_ERR(imx_data->clk_per)) {
1679 		err = PTR_ERR(imx_data->clk_per);
1680 		goto free_sdhci;
1681 	}
1682 
1683 	pltfm_host->clk = imx_data->clk_per;
1684 	pltfm_host->clock = clk_get_rate(pltfm_host->clk);
1685 	err = clk_prepare_enable(imx_data->clk_per);
1686 	if (err)
1687 		goto free_sdhci;
1688 	err = clk_prepare_enable(imx_data->clk_ipg);
1689 	if (err)
1690 		goto disable_per_clk;
1691 	err = clk_prepare_enable(imx_data->clk_ahb);
1692 	if (err)
1693 		goto disable_ipg_clk;
1694 
1695 	imx_data->pinctrl = devm_pinctrl_get(&pdev->dev);
1696 	if (IS_ERR(imx_data->pinctrl))
1697 		dev_warn(mmc_dev(host->mmc), "could not get pinctrl\n");
1698 
1699 	if (esdhc_is_usdhc(imx_data)) {
1700 		host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
1701 		host->mmc->caps |= MMC_CAP_1_8V_DDR | MMC_CAP_3_3V_DDR;
1702 
1703 		/* GPIO CD can be set as a wakeup source */
1704 		host->mmc->caps |= MMC_CAP_CD_WAKE;
1705 
1706 		if (!(imx_data->socdata->flags & ESDHC_FLAG_HS200))
1707 			host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200;
1708 
1709 		/* clear tuning bits in case ROM has set it already */
1710 		writel(0x0, host->ioaddr + ESDHC_MIX_CTRL);
1711 		writel(0x0, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1712 		writel(0x0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1713 
1714 		/*
1715 		 * Link usdhc specific mmc_host_ops execute_tuning function,
1716 		 * to replace the standard one in sdhci_ops.
1717 		 */
1718 		host->mmc_host_ops.execute_tuning = usdhc_execute_tuning;
1719 
1720 		/*
1721 		 * Link usdhc specific mmc_host_ops init card function,
1722 		 * to distinguish the card type.
1723 		 */
1724 		host->mmc_host_ops.init_card = usdhc_init_card;
1725 	}
1726 
1727 	err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
1728 	if (err)
1729 		goto disable_ahb_clk;
1730 
1731 	if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
1732 		sdhci_esdhc_ops.platform_execute_tuning =
1733 					esdhc_executing_tuning;
1734 
1735 	if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
1736 		host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
1737 
1738 	if (host->mmc->caps & MMC_CAP_8_BIT_DATA &&
1739 	    imx_data->socdata->flags & ESDHC_FLAG_HS400)
1740 		host->mmc->caps2 |= MMC_CAP2_HS400;
1741 
1742 	if (imx_data->socdata->flags & ESDHC_FLAG_BROKEN_AUTO_CMD23)
1743 		host->quirks2 |= SDHCI_QUIRK2_ACMD23_BROKEN;
1744 
1745 	if (host->mmc->caps & MMC_CAP_8_BIT_DATA &&
1746 	    imx_data->socdata->flags & ESDHC_FLAG_HS400_ES) {
1747 		host->mmc->caps2 |= MMC_CAP2_HS400_ES;
1748 		host->mmc_host_ops.hs400_enhanced_strobe =
1749 					esdhc_hs400_enhanced_strobe;
1750 	}
1751 
1752 	if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) {
1753 		host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
1754 		cq_host = devm_kzalloc(&pdev->dev, sizeof(*cq_host), GFP_KERNEL);
1755 		if (!cq_host) {
1756 			err = -ENOMEM;
1757 			goto disable_ahb_clk;
1758 		}
1759 
1760 		cq_host->mmio = host->ioaddr + ESDHC_CQHCI_ADDR_OFFSET;
1761 		cq_host->ops = &esdhc_cqhci_ops;
1762 
1763 		err = cqhci_init(cq_host, host->mmc, false);
1764 		if (err)
1765 			goto disable_ahb_clk;
1766 	}
1767 
1768 	sdhci_esdhc_imx_hwinit(host);
1769 
1770 	err = sdhci_add_host(host);
1771 	if (err)
1772 		goto disable_ahb_clk;
1773 
1774 	/*
1775 	 * Setup the wakeup capability here, let user to decide
1776 	 * whether need to enable this wakeup through sysfs interface.
1777 	 */
1778 	if ((host->mmc->pm_caps & MMC_PM_KEEP_POWER) &&
1779 			(host->mmc->pm_caps & MMC_PM_WAKE_SDIO_IRQ))
1780 		device_set_wakeup_capable(&pdev->dev, true);
1781 
1782 	pm_runtime_set_active(&pdev->dev);
1783 	pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
1784 	pm_runtime_use_autosuspend(&pdev->dev);
1785 	pm_suspend_ignore_children(&pdev->dev, 1);
1786 	pm_runtime_enable(&pdev->dev);
1787 
1788 	return 0;
1789 
1790 disable_ahb_clk:
1791 	clk_disable_unprepare(imx_data->clk_ahb);
1792 disable_ipg_clk:
1793 	clk_disable_unprepare(imx_data->clk_ipg);
1794 disable_per_clk:
1795 	clk_disable_unprepare(imx_data->clk_per);
1796 free_sdhci:
1797 	if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1798 		cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1799 	sdhci_pltfm_free(pdev);
1800 	return err;
1801 }
1802 
1803 static int sdhci_esdhc_imx_remove(struct platform_device *pdev)
1804 {
1805 	struct sdhci_host *host = platform_get_drvdata(pdev);
1806 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1807 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1808 	int dead;
1809 
1810 	pm_runtime_get_sync(&pdev->dev);
1811 	dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
1812 	pm_runtime_disable(&pdev->dev);
1813 	pm_runtime_put_noidle(&pdev->dev);
1814 
1815 	sdhci_remove_host(host, dead);
1816 
1817 	clk_disable_unprepare(imx_data->clk_per);
1818 	clk_disable_unprepare(imx_data->clk_ipg);
1819 	clk_disable_unprepare(imx_data->clk_ahb);
1820 
1821 	if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1822 		cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1823 
1824 	sdhci_pltfm_free(pdev);
1825 
1826 	return 0;
1827 }
1828 
1829 #ifdef CONFIG_PM_SLEEP
1830 static int sdhci_esdhc_suspend(struct device *dev)
1831 {
1832 	struct sdhci_host *host = dev_get_drvdata(dev);
1833 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1834 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1835 	int ret;
1836 
1837 	if (host->mmc->caps2 & MMC_CAP2_CQE) {
1838 		ret = cqhci_suspend(host->mmc);
1839 		if (ret)
1840 			return ret;
1841 	}
1842 
1843 	if ((imx_data->socdata->flags & ESDHC_FLAG_STATE_LOST_IN_LPMODE) &&
1844 		(host->tuning_mode != SDHCI_TUNING_MODE_1)) {
1845 		mmc_retune_timer_stop(host->mmc);
1846 		mmc_retune_needed(host->mmc);
1847 	}
1848 
1849 	if (host->tuning_mode != SDHCI_TUNING_MODE_3)
1850 		mmc_retune_needed(host->mmc);
1851 
1852 	ret = sdhci_suspend_host(host);
1853 	if (ret)
1854 		return ret;
1855 
1856 	ret = pinctrl_pm_select_sleep_state(dev);
1857 	if (ret)
1858 		return ret;
1859 
1860 	ret = mmc_gpio_set_cd_wake(host->mmc, true);
1861 
1862 	return ret;
1863 }
1864 
1865 static int sdhci_esdhc_resume(struct device *dev)
1866 {
1867 	struct sdhci_host *host = dev_get_drvdata(dev);
1868 	int ret;
1869 
1870 	ret = pinctrl_pm_select_default_state(dev);
1871 	if (ret)
1872 		return ret;
1873 
1874 	/* re-initialize hw state in case it's lost in low power mode */
1875 	sdhci_esdhc_imx_hwinit(host);
1876 
1877 	ret = sdhci_resume_host(host);
1878 	if (ret)
1879 		return ret;
1880 
1881 	if (host->mmc->caps2 & MMC_CAP2_CQE)
1882 		ret = cqhci_resume(host->mmc);
1883 
1884 	if (!ret)
1885 		ret = mmc_gpio_set_cd_wake(host->mmc, false);
1886 
1887 	return ret;
1888 }
1889 #endif
1890 
1891 #ifdef CONFIG_PM
1892 static int sdhci_esdhc_runtime_suspend(struct device *dev)
1893 {
1894 	struct sdhci_host *host = dev_get_drvdata(dev);
1895 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1896 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1897 	int ret;
1898 
1899 	if (host->mmc->caps2 & MMC_CAP2_CQE) {
1900 		ret = cqhci_suspend(host->mmc);
1901 		if (ret)
1902 			return ret;
1903 	}
1904 
1905 	ret = sdhci_runtime_suspend_host(host);
1906 	if (ret)
1907 		return ret;
1908 
1909 	if (host->tuning_mode != SDHCI_TUNING_MODE_3)
1910 		mmc_retune_needed(host->mmc);
1911 
1912 	imx_data->actual_clock = host->mmc->actual_clock;
1913 	esdhc_pltfm_set_clock(host, 0);
1914 	clk_disable_unprepare(imx_data->clk_per);
1915 	clk_disable_unprepare(imx_data->clk_ipg);
1916 	clk_disable_unprepare(imx_data->clk_ahb);
1917 
1918 	if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1919 		cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1920 
1921 	return ret;
1922 }
1923 
1924 static int sdhci_esdhc_runtime_resume(struct device *dev)
1925 {
1926 	struct sdhci_host *host = dev_get_drvdata(dev);
1927 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1928 	struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1929 	int err;
1930 
1931 	if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1932 		cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0);
1933 
1934 	if (imx_data->socdata->flags & ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME)
1935 		clk_set_rate(imx_data->clk_per, pltfm_host->clock);
1936 
1937 	err = clk_prepare_enable(imx_data->clk_ahb);
1938 	if (err)
1939 		goto remove_pm_qos_request;
1940 
1941 	err = clk_prepare_enable(imx_data->clk_per);
1942 	if (err)
1943 		goto disable_ahb_clk;
1944 
1945 	err = clk_prepare_enable(imx_data->clk_ipg);
1946 	if (err)
1947 		goto disable_per_clk;
1948 
1949 	esdhc_pltfm_set_clock(host, imx_data->actual_clock);
1950 
1951 	err = sdhci_runtime_resume_host(host, 0);
1952 	if (err)
1953 		goto disable_ipg_clk;
1954 
1955 	if (host->mmc->caps2 & MMC_CAP2_CQE)
1956 		err = cqhci_resume(host->mmc);
1957 
1958 	return err;
1959 
1960 disable_ipg_clk:
1961 	clk_disable_unprepare(imx_data->clk_ipg);
1962 disable_per_clk:
1963 	clk_disable_unprepare(imx_data->clk_per);
1964 disable_ahb_clk:
1965 	clk_disable_unprepare(imx_data->clk_ahb);
1966 remove_pm_qos_request:
1967 	if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1968 		cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1969 	return err;
1970 }
1971 #endif
1972 
1973 static const struct dev_pm_ops sdhci_esdhc_pmops = {
1974 	SET_SYSTEM_SLEEP_PM_OPS(sdhci_esdhc_suspend, sdhci_esdhc_resume)
1975 	SET_RUNTIME_PM_OPS(sdhci_esdhc_runtime_suspend,
1976 				sdhci_esdhc_runtime_resume, NULL)
1977 };
1978 
1979 static struct platform_driver sdhci_esdhc_imx_driver = {
1980 	.driver		= {
1981 		.name	= "sdhci-esdhc-imx",
1982 		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
1983 		.of_match_table = imx_esdhc_dt_ids,
1984 		.pm	= &sdhci_esdhc_pmops,
1985 	},
1986 	.probe		= sdhci_esdhc_imx_probe,
1987 	.remove		= sdhci_esdhc_imx_remove,
1988 };
1989 
1990 module_platform_driver(sdhci_esdhc_imx_driver);
1991 
1992 MODULE_DESCRIPTION("SDHCI driver for Freescale i.MX eSDHC");
1993 MODULE_AUTHOR("Wolfram Sang <kernel@pengutronix.de>");
1994 MODULE_LICENSE("GPL v2");
1995