1 /* 2 * linux/drivers/mmc/host/mmci.c - ARM PrimeCell MMCI PL180/1 driver 3 * 4 * Copyright (C) 2003 Deep Blue Solutions, Ltd, All Rights Reserved. 5 * Copyright (C) 2010 ST-Ericsson SA 6 * 7 * This program is free software; you can redistribute it and/or modify 8 * it under the terms of the GNU General Public License version 2 as 9 * published by the Free Software Foundation. 10 */ 11 #include <linux/module.h> 12 #include <linux/moduleparam.h> 13 #include <linux/init.h> 14 #include <linux/ioport.h> 15 #include <linux/device.h> 16 #include <linux/io.h> 17 #include <linux/interrupt.h> 18 #include <linux/kernel.h> 19 #include <linux/slab.h> 20 #include <linux/delay.h> 21 #include <linux/err.h> 22 #include <linux/highmem.h> 23 #include <linux/log2.h> 24 #include <linux/mmc/pm.h> 25 #include <linux/mmc/host.h> 26 #include <linux/mmc/card.h> 27 #include <linux/mmc/slot-gpio.h> 28 #include <linux/amba/bus.h> 29 #include <linux/clk.h> 30 #include <linux/scatterlist.h> 31 #include <linux/gpio.h> 32 #include <linux/of_gpio.h> 33 #include <linux/regulator/consumer.h> 34 #include <linux/dmaengine.h> 35 #include <linux/dma-mapping.h> 36 #include <linux/amba/mmci.h> 37 #include <linux/pm_runtime.h> 38 #include <linux/types.h> 39 #include <linux/pinctrl/consumer.h> 40 41 #include <asm/div64.h> 42 #include <asm/io.h> 43 44 #include "mmci.h" 45 #include "mmci_qcom_dml.h" 46 47 #define DRIVER_NAME "mmci-pl18x" 48 49 static unsigned int fmax = 515633; 50 51 /** 52 * struct variant_data - MMCI variant-specific quirks 53 * @clkreg: default value for MCICLOCK register 54 * @clkreg_enable: enable value for MMCICLOCK register 55 * @clkreg_8bit_bus_enable: enable value for 8 bit bus 56 * @clkreg_neg_edge_enable: enable value for inverted data/cmd output 57 * @datalength_bits: number of bits in the MMCIDATALENGTH register 58 * @fifosize: number of bytes that can be written when MMCI_TXFIFOEMPTY 59 * is asserted (likewise for RX) 60 * @fifohalfsize: number of bytes that can be written when MCI_TXFIFOHALFEMPTY 61 * is asserted (likewise for RX) 62 * @data_cmd_enable: enable value for data commands. 63 * @st_sdio: enable ST specific SDIO logic 64 * @st_clkdiv: true if using a ST-specific clock divider algorithm 65 * @datactrl_mask_ddrmode: ddr mode mask in datactrl register. 66 * @blksz_datactrl16: true if Block size is at b16..b30 position in datactrl register 67 * @blksz_datactrl4: true if Block size is at b4..b16 position in datactrl 68 * register 69 * @datactrl_mask_sdio: SDIO enable mask in datactrl register 70 * @pwrreg_powerup: power up value for MMCIPOWER register 71 * @f_max: maximum clk frequency supported by the controller. 72 * @signal_direction: input/out direction of bus signals can be indicated 73 * @pwrreg_clkgate: MMCIPOWER register must be used to gate the clock 74 * @busy_detect: true if the variant supports busy detection on DAT0. 75 * @busy_dpsm_flag: bitmask enabling busy detection in the DPSM 76 * @busy_detect_flag: bitmask identifying the bit in the MMCISTATUS register 77 * indicating that the card is busy 78 * @busy_detect_mask: bitmask identifying the bit in the MMCIMASK0 to mask for 79 * getting busy end detection interrupts 80 * @pwrreg_nopower: bits in MMCIPOWER don't controls ext. power supply 81 * @explicit_mclk_control: enable explicit mclk control in driver. 82 * @qcom_fifo: enables qcom specific fifo pio read logic. 83 * @qcom_dml: enables qcom specific dma glue for dma transfers. 84 * @reversed_irq_handling: handle data irq before cmd irq. 85 * @mmcimask1: true if variant have a MMCIMASK1 register. 86 * @start_err: bitmask identifying the STARTBITERR bit inside MMCISTATUS 87 * register. 88 * @opendrain: bitmask identifying the OPENDRAIN bit inside MMCIPOWER register 89 */ 90 struct variant_data { 91 unsigned int clkreg; 92 unsigned int clkreg_enable; 93 unsigned int clkreg_8bit_bus_enable; 94 unsigned int clkreg_neg_edge_enable; 95 unsigned int datalength_bits; 96 unsigned int fifosize; 97 unsigned int fifohalfsize; 98 unsigned int data_cmd_enable; 99 unsigned int datactrl_mask_ddrmode; 100 unsigned int datactrl_mask_sdio; 101 bool st_sdio; 102 bool st_clkdiv; 103 bool blksz_datactrl16; 104 bool blksz_datactrl4; 105 u32 pwrreg_powerup; 106 u32 f_max; 107 bool signal_direction; 108 bool pwrreg_clkgate; 109 bool busy_detect; 110 u32 busy_dpsm_flag; 111 u32 busy_detect_flag; 112 u32 busy_detect_mask; 113 bool pwrreg_nopower; 114 bool explicit_mclk_control; 115 bool qcom_fifo; 116 bool qcom_dml; 117 bool reversed_irq_handling; 118 bool mmcimask1; 119 u32 start_err; 120 u32 opendrain; 121 }; 122 123 static struct variant_data variant_arm = { 124 .fifosize = 16 * 4, 125 .fifohalfsize = 8 * 4, 126 .datalength_bits = 16, 127 .pwrreg_powerup = MCI_PWR_UP, 128 .f_max = 100000000, 129 .reversed_irq_handling = true, 130 .mmcimask1 = true, 131 .start_err = MCI_STARTBITERR, 132 .opendrain = MCI_ROD, 133 }; 134 135 static struct variant_data variant_arm_extended_fifo = { 136 .fifosize = 128 * 4, 137 .fifohalfsize = 64 * 4, 138 .datalength_bits = 16, 139 .pwrreg_powerup = MCI_PWR_UP, 140 .f_max = 100000000, 141 .mmcimask1 = true, 142 .start_err = MCI_STARTBITERR, 143 .opendrain = MCI_ROD, 144 }; 145 146 static struct variant_data variant_arm_extended_fifo_hwfc = { 147 .fifosize = 128 * 4, 148 .fifohalfsize = 64 * 4, 149 .clkreg_enable = MCI_ARM_HWFCEN, 150 .datalength_bits = 16, 151 .pwrreg_powerup = MCI_PWR_UP, 152 .f_max = 100000000, 153 .mmcimask1 = true, 154 .start_err = MCI_STARTBITERR, 155 .opendrain = MCI_ROD, 156 }; 157 158 static struct variant_data variant_u300 = { 159 .fifosize = 16 * 4, 160 .fifohalfsize = 8 * 4, 161 .clkreg_enable = MCI_ST_U300_HWFCEN, 162 .clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS, 163 .datalength_bits = 16, 164 .datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN, 165 .st_sdio = true, 166 .pwrreg_powerup = MCI_PWR_ON, 167 .f_max = 100000000, 168 .signal_direction = true, 169 .pwrreg_clkgate = true, 170 .pwrreg_nopower = true, 171 .mmcimask1 = true, 172 .start_err = MCI_STARTBITERR, 173 .opendrain = MCI_OD, 174 }; 175 176 static struct variant_data variant_nomadik = { 177 .fifosize = 16 * 4, 178 .fifohalfsize = 8 * 4, 179 .clkreg = MCI_CLK_ENABLE, 180 .clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS, 181 .datalength_bits = 24, 182 .datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN, 183 .st_sdio = true, 184 .st_clkdiv = true, 185 .pwrreg_powerup = MCI_PWR_ON, 186 .f_max = 100000000, 187 .signal_direction = true, 188 .pwrreg_clkgate = true, 189 .pwrreg_nopower = true, 190 .mmcimask1 = true, 191 .start_err = MCI_STARTBITERR, 192 .opendrain = MCI_OD, 193 }; 194 195 static struct variant_data variant_ux500 = { 196 .fifosize = 30 * 4, 197 .fifohalfsize = 8 * 4, 198 .clkreg = MCI_CLK_ENABLE, 199 .clkreg_enable = MCI_ST_UX500_HWFCEN, 200 .clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS, 201 .clkreg_neg_edge_enable = MCI_ST_UX500_NEG_EDGE, 202 .datalength_bits = 24, 203 .datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN, 204 .st_sdio = true, 205 .st_clkdiv = true, 206 .pwrreg_powerup = MCI_PWR_ON, 207 .f_max = 100000000, 208 .signal_direction = true, 209 .pwrreg_clkgate = true, 210 .busy_detect = true, 211 .busy_dpsm_flag = MCI_DPSM_ST_BUSYMODE, 212 .busy_detect_flag = MCI_ST_CARDBUSY, 213 .busy_detect_mask = MCI_ST_BUSYENDMASK, 214 .pwrreg_nopower = true, 215 .mmcimask1 = true, 216 .start_err = MCI_STARTBITERR, 217 .opendrain = MCI_OD, 218 }; 219 220 static struct variant_data variant_ux500v2 = { 221 .fifosize = 30 * 4, 222 .fifohalfsize = 8 * 4, 223 .clkreg = MCI_CLK_ENABLE, 224 .clkreg_enable = MCI_ST_UX500_HWFCEN, 225 .clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS, 226 .clkreg_neg_edge_enable = MCI_ST_UX500_NEG_EDGE, 227 .datactrl_mask_ddrmode = MCI_DPSM_ST_DDRMODE, 228 .datalength_bits = 24, 229 .datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN, 230 .st_sdio = true, 231 .st_clkdiv = true, 232 .blksz_datactrl16 = true, 233 .pwrreg_powerup = MCI_PWR_ON, 234 .f_max = 100000000, 235 .signal_direction = true, 236 .pwrreg_clkgate = true, 237 .busy_detect = true, 238 .busy_dpsm_flag = MCI_DPSM_ST_BUSYMODE, 239 .busy_detect_flag = MCI_ST_CARDBUSY, 240 .busy_detect_mask = MCI_ST_BUSYENDMASK, 241 .pwrreg_nopower = true, 242 .mmcimask1 = true, 243 .start_err = MCI_STARTBITERR, 244 .opendrain = MCI_OD, 245 }; 246 247 static struct variant_data variant_stm32 = { 248 .fifosize = 32 * 4, 249 .fifohalfsize = 8 * 4, 250 .clkreg = MCI_CLK_ENABLE, 251 .clkreg_enable = MCI_ST_UX500_HWFCEN, 252 .clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS, 253 .clkreg_neg_edge_enable = MCI_ST_UX500_NEG_EDGE, 254 .datalength_bits = 24, 255 .datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN, 256 .st_sdio = true, 257 .st_clkdiv = true, 258 .pwrreg_powerup = MCI_PWR_ON, 259 .f_max = 48000000, 260 .pwrreg_clkgate = true, 261 .pwrreg_nopower = true, 262 }; 263 264 static struct variant_data variant_qcom = { 265 .fifosize = 16 * 4, 266 .fifohalfsize = 8 * 4, 267 .clkreg = MCI_CLK_ENABLE, 268 .clkreg_enable = MCI_QCOM_CLK_FLOWENA | 269 MCI_QCOM_CLK_SELECT_IN_FBCLK, 270 .clkreg_8bit_bus_enable = MCI_QCOM_CLK_WIDEBUS_8, 271 .datactrl_mask_ddrmode = MCI_QCOM_CLK_SELECT_IN_DDR_MODE, 272 .data_cmd_enable = MCI_CPSM_QCOM_DATCMD, 273 .blksz_datactrl4 = true, 274 .datalength_bits = 24, 275 .pwrreg_powerup = MCI_PWR_UP, 276 .f_max = 208000000, 277 .explicit_mclk_control = true, 278 .qcom_fifo = true, 279 .qcom_dml = true, 280 .mmcimask1 = true, 281 .start_err = MCI_STARTBITERR, 282 .opendrain = MCI_ROD, 283 }; 284 285 /* Busy detection for the ST Micro variant */ 286 static int mmci_card_busy(struct mmc_host *mmc) 287 { 288 struct mmci_host *host = mmc_priv(mmc); 289 unsigned long flags; 290 int busy = 0; 291 292 spin_lock_irqsave(&host->lock, flags); 293 if (readl(host->base + MMCISTATUS) & host->variant->busy_detect_flag) 294 busy = 1; 295 spin_unlock_irqrestore(&host->lock, flags); 296 297 return busy; 298 } 299 300 /* 301 * Validate mmc prerequisites 302 */ 303 static int mmci_validate_data(struct mmci_host *host, 304 struct mmc_data *data) 305 { 306 if (!data) 307 return 0; 308 309 if (!is_power_of_2(data->blksz)) { 310 dev_err(mmc_dev(host->mmc), 311 "unsupported block size (%d bytes)\n", data->blksz); 312 return -EINVAL; 313 } 314 315 return 0; 316 } 317 318 static void mmci_reg_delay(struct mmci_host *host) 319 { 320 /* 321 * According to the spec, at least three feedback clock cycles 322 * of max 52 MHz must pass between two writes to the MMCICLOCK reg. 323 * Three MCLK clock cycles must pass between two MMCIPOWER reg writes. 324 * Worst delay time during card init is at 100 kHz => 30 us. 325 * Worst delay time when up and running is at 25 MHz => 120 ns. 326 */ 327 if (host->cclk < 25000000) 328 udelay(30); 329 else 330 ndelay(120); 331 } 332 333 /* 334 * This must be called with host->lock held 335 */ 336 static void mmci_write_clkreg(struct mmci_host *host, u32 clk) 337 { 338 if (host->clk_reg != clk) { 339 host->clk_reg = clk; 340 writel(clk, host->base + MMCICLOCK); 341 } 342 } 343 344 /* 345 * This must be called with host->lock held 346 */ 347 static void mmci_write_pwrreg(struct mmci_host *host, u32 pwr) 348 { 349 if (host->pwr_reg != pwr) { 350 host->pwr_reg = pwr; 351 writel(pwr, host->base + MMCIPOWER); 352 } 353 } 354 355 /* 356 * This must be called with host->lock held 357 */ 358 static void mmci_write_datactrlreg(struct mmci_host *host, u32 datactrl) 359 { 360 /* Keep busy mode in DPSM if enabled */ 361 datactrl |= host->datactrl_reg & host->variant->busy_dpsm_flag; 362 363 if (host->datactrl_reg != datactrl) { 364 host->datactrl_reg = datactrl; 365 writel(datactrl, host->base + MMCIDATACTRL); 366 } 367 } 368 369 /* 370 * This must be called with host->lock held 371 */ 372 static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired) 373 { 374 struct variant_data *variant = host->variant; 375 u32 clk = variant->clkreg; 376 377 /* Make sure cclk reflects the current calculated clock */ 378 host->cclk = 0; 379 380 if (desired) { 381 if (variant->explicit_mclk_control) { 382 host->cclk = host->mclk; 383 } else if (desired >= host->mclk) { 384 clk = MCI_CLK_BYPASS; 385 if (variant->st_clkdiv) 386 clk |= MCI_ST_UX500_NEG_EDGE; 387 host->cclk = host->mclk; 388 } else if (variant->st_clkdiv) { 389 /* 390 * DB8500 TRM says f = mclk / (clkdiv + 2) 391 * => clkdiv = (mclk / f) - 2 392 * Round the divider up so we don't exceed the max 393 * frequency 394 */ 395 clk = DIV_ROUND_UP(host->mclk, desired) - 2; 396 if (clk >= 256) 397 clk = 255; 398 host->cclk = host->mclk / (clk + 2); 399 } else { 400 /* 401 * PL180 TRM says f = mclk / (2 * (clkdiv + 1)) 402 * => clkdiv = mclk / (2 * f) - 1 403 */ 404 clk = host->mclk / (2 * desired) - 1; 405 if (clk >= 256) 406 clk = 255; 407 host->cclk = host->mclk / (2 * (clk + 1)); 408 } 409 410 clk |= variant->clkreg_enable; 411 clk |= MCI_CLK_ENABLE; 412 /* This hasn't proven to be worthwhile */ 413 /* clk |= MCI_CLK_PWRSAVE; */ 414 } 415 416 /* Set actual clock for debug */ 417 host->mmc->actual_clock = host->cclk; 418 419 if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4) 420 clk |= MCI_4BIT_BUS; 421 if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8) 422 clk |= variant->clkreg_8bit_bus_enable; 423 424 if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50 || 425 host->mmc->ios.timing == MMC_TIMING_MMC_DDR52) 426 clk |= variant->clkreg_neg_edge_enable; 427 428 mmci_write_clkreg(host, clk); 429 } 430 431 static void 432 mmci_request_end(struct mmci_host *host, struct mmc_request *mrq) 433 { 434 writel(0, host->base + MMCICOMMAND); 435 436 BUG_ON(host->data); 437 438 host->mrq = NULL; 439 host->cmd = NULL; 440 441 mmc_request_done(host->mmc, mrq); 442 } 443 444 static void mmci_set_mask1(struct mmci_host *host, unsigned int mask) 445 { 446 void __iomem *base = host->base; 447 struct variant_data *variant = host->variant; 448 449 if (host->singleirq) { 450 unsigned int mask0 = readl(base + MMCIMASK0); 451 452 mask0 &= ~MCI_IRQ1MASK; 453 mask0 |= mask; 454 455 writel(mask0, base + MMCIMASK0); 456 } 457 458 if (variant->mmcimask1) 459 writel(mask, base + MMCIMASK1); 460 461 host->mask1_reg = mask; 462 } 463 464 static void mmci_stop_data(struct mmci_host *host) 465 { 466 mmci_write_datactrlreg(host, 0); 467 mmci_set_mask1(host, 0); 468 host->data = NULL; 469 } 470 471 static void mmci_init_sg(struct mmci_host *host, struct mmc_data *data) 472 { 473 unsigned int flags = SG_MITER_ATOMIC; 474 475 if (data->flags & MMC_DATA_READ) 476 flags |= SG_MITER_TO_SG; 477 else 478 flags |= SG_MITER_FROM_SG; 479 480 sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags); 481 } 482 483 /* 484 * All the DMA operation mode stuff goes inside this ifdef. 485 * This assumes that you have a generic DMA device interface, 486 * no custom DMA interfaces are supported. 487 */ 488 #ifdef CONFIG_DMA_ENGINE 489 static void mmci_dma_setup(struct mmci_host *host) 490 { 491 const char *rxname, *txname; 492 struct variant_data *variant = host->variant; 493 494 host->dma_rx_channel = dma_request_slave_channel(mmc_dev(host->mmc), "rx"); 495 host->dma_tx_channel = dma_request_slave_channel(mmc_dev(host->mmc), "tx"); 496 497 /* initialize pre request cookie */ 498 host->next_data.cookie = 1; 499 500 /* 501 * If only an RX channel is specified, the driver will 502 * attempt to use it bidirectionally, however if it is 503 * is specified but cannot be located, DMA will be disabled. 504 */ 505 if (host->dma_rx_channel && !host->dma_tx_channel) 506 host->dma_tx_channel = host->dma_rx_channel; 507 508 if (host->dma_rx_channel) 509 rxname = dma_chan_name(host->dma_rx_channel); 510 else 511 rxname = "none"; 512 513 if (host->dma_tx_channel) 514 txname = dma_chan_name(host->dma_tx_channel); 515 else 516 txname = "none"; 517 518 dev_info(mmc_dev(host->mmc), "DMA channels RX %s, TX %s\n", 519 rxname, txname); 520 521 /* 522 * Limit the maximum segment size in any SG entry according to 523 * the parameters of the DMA engine device. 524 */ 525 if (host->dma_tx_channel) { 526 struct device *dev = host->dma_tx_channel->device->dev; 527 unsigned int max_seg_size = dma_get_max_seg_size(dev); 528 529 if (max_seg_size < host->mmc->max_seg_size) 530 host->mmc->max_seg_size = max_seg_size; 531 } 532 if (host->dma_rx_channel) { 533 struct device *dev = host->dma_rx_channel->device->dev; 534 unsigned int max_seg_size = dma_get_max_seg_size(dev); 535 536 if (max_seg_size < host->mmc->max_seg_size) 537 host->mmc->max_seg_size = max_seg_size; 538 } 539 540 if (variant->qcom_dml && host->dma_rx_channel && host->dma_tx_channel) 541 if (dml_hw_init(host, host->mmc->parent->of_node)) 542 variant->qcom_dml = false; 543 } 544 545 /* 546 * This is used in or so inline it 547 * so it can be discarded. 548 */ 549 static inline void mmci_dma_release(struct mmci_host *host) 550 { 551 if (host->dma_rx_channel) 552 dma_release_channel(host->dma_rx_channel); 553 if (host->dma_tx_channel) 554 dma_release_channel(host->dma_tx_channel); 555 host->dma_rx_channel = host->dma_tx_channel = NULL; 556 } 557 558 static void mmci_dma_data_error(struct mmci_host *host) 559 { 560 dev_err(mmc_dev(host->mmc), "error during DMA transfer!\n"); 561 dmaengine_terminate_all(host->dma_current); 562 host->dma_in_progress = false; 563 host->dma_current = NULL; 564 host->dma_desc_current = NULL; 565 host->data->host_cookie = 0; 566 } 567 568 static void mmci_dma_unmap(struct mmci_host *host, struct mmc_data *data) 569 { 570 struct dma_chan *chan; 571 572 if (data->flags & MMC_DATA_READ) 573 chan = host->dma_rx_channel; 574 else 575 chan = host->dma_tx_channel; 576 577 dma_unmap_sg(chan->device->dev, data->sg, data->sg_len, 578 mmc_get_dma_dir(data)); 579 } 580 581 static void mmci_dma_finalize(struct mmci_host *host, struct mmc_data *data) 582 { 583 u32 status; 584 int i; 585 586 /* Wait up to 1ms for the DMA to complete */ 587 for (i = 0; ; i++) { 588 status = readl(host->base + MMCISTATUS); 589 if (!(status & MCI_RXDATAAVLBLMASK) || i >= 100) 590 break; 591 udelay(10); 592 } 593 594 /* 595 * Check to see whether we still have some data left in the FIFO - 596 * this catches DMA controllers which are unable to monitor the 597 * DMALBREQ and DMALSREQ signals while allowing us to DMA to non- 598 * contiguous buffers. On TX, we'll get a FIFO underrun error. 599 */ 600 if (status & MCI_RXDATAAVLBLMASK) { 601 mmci_dma_data_error(host); 602 if (!data->error) 603 data->error = -EIO; 604 } 605 606 if (!data->host_cookie) 607 mmci_dma_unmap(host, data); 608 609 /* 610 * Use of DMA with scatter-gather is impossible. 611 * Give up with DMA and switch back to PIO mode. 612 */ 613 if (status & MCI_RXDATAAVLBLMASK) { 614 dev_err(mmc_dev(host->mmc), "buggy DMA detected. Taking evasive action.\n"); 615 mmci_dma_release(host); 616 } 617 618 host->dma_in_progress = false; 619 host->dma_current = NULL; 620 host->dma_desc_current = NULL; 621 } 622 623 /* prepares DMA channel and DMA descriptor, returns non-zero on failure */ 624 static int __mmci_dma_prep_data(struct mmci_host *host, struct mmc_data *data, 625 struct dma_chan **dma_chan, 626 struct dma_async_tx_descriptor **dma_desc) 627 { 628 struct variant_data *variant = host->variant; 629 struct dma_slave_config conf = { 630 .src_addr = host->phybase + MMCIFIFO, 631 .dst_addr = host->phybase + MMCIFIFO, 632 .src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES, 633 .dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES, 634 .src_maxburst = variant->fifohalfsize >> 2, /* # of words */ 635 .dst_maxburst = variant->fifohalfsize >> 2, /* # of words */ 636 .device_fc = false, 637 }; 638 struct dma_chan *chan; 639 struct dma_device *device; 640 struct dma_async_tx_descriptor *desc; 641 int nr_sg; 642 unsigned long flags = DMA_CTRL_ACK; 643 644 if (data->flags & MMC_DATA_READ) { 645 conf.direction = DMA_DEV_TO_MEM; 646 chan = host->dma_rx_channel; 647 } else { 648 conf.direction = DMA_MEM_TO_DEV; 649 chan = host->dma_tx_channel; 650 } 651 652 /* If there's no DMA channel, fall back to PIO */ 653 if (!chan) 654 return -EINVAL; 655 656 /* If less than or equal to the fifo size, don't bother with DMA */ 657 if (data->blksz * data->blocks <= variant->fifosize) 658 return -EINVAL; 659 660 device = chan->device; 661 nr_sg = dma_map_sg(device->dev, data->sg, data->sg_len, 662 mmc_get_dma_dir(data)); 663 if (nr_sg == 0) 664 return -EINVAL; 665 666 if (host->variant->qcom_dml) 667 flags |= DMA_PREP_INTERRUPT; 668 669 dmaengine_slave_config(chan, &conf); 670 desc = dmaengine_prep_slave_sg(chan, data->sg, nr_sg, 671 conf.direction, flags); 672 if (!desc) 673 goto unmap_exit; 674 675 *dma_chan = chan; 676 *dma_desc = desc; 677 678 return 0; 679 680 unmap_exit: 681 dma_unmap_sg(device->dev, data->sg, data->sg_len, 682 mmc_get_dma_dir(data)); 683 return -ENOMEM; 684 } 685 686 static inline int mmci_dma_prep_data(struct mmci_host *host, 687 struct mmc_data *data) 688 { 689 /* Check if next job is already prepared. */ 690 if (host->dma_current && host->dma_desc_current) 691 return 0; 692 693 /* No job were prepared thus do it now. */ 694 return __mmci_dma_prep_data(host, data, &host->dma_current, 695 &host->dma_desc_current); 696 } 697 698 static inline int mmci_dma_prep_next(struct mmci_host *host, 699 struct mmc_data *data) 700 { 701 struct mmci_host_next *nd = &host->next_data; 702 return __mmci_dma_prep_data(host, data, &nd->dma_chan, &nd->dma_desc); 703 } 704 705 static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl) 706 { 707 int ret; 708 struct mmc_data *data = host->data; 709 710 ret = mmci_dma_prep_data(host, host->data); 711 if (ret) 712 return ret; 713 714 /* Okay, go for it. */ 715 dev_vdbg(mmc_dev(host->mmc), 716 "Submit MMCI DMA job, sglen %d blksz %04x blks %04x flags %08x\n", 717 data->sg_len, data->blksz, data->blocks, data->flags); 718 host->dma_in_progress = true; 719 dmaengine_submit(host->dma_desc_current); 720 dma_async_issue_pending(host->dma_current); 721 722 if (host->variant->qcom_dml) 723 dml_start_xfer(host, data); 724 725 datactrl |= MCI_DPSM_DMAENABLE; 726 727 /* Trigger the DMA transfer */ 728 mmci_write_datactrlreg(host, datactrl); 729 730 /* 731 * Let the MMCI say when the data is ended and it's time 732 * to fire next DMA request. When that happens, MMCI will 733 * call mmci_data_end() 734 */ 735 writel(readl(host->base + MMCIMASK0) | MCI_DATAENDMASK, 736 host->base + MMCIMASK0); 737 return 0; 738 } 739 740 static void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data) 741 { 742 struct mmci_host_next *next = &host->next_data; 743 744 WARN_ON(data->host_cookie && data->host_cookie != next->cookie); 745 WARN_ON(!data->host_cookie && (next->dma_desc || next->dma_chan)); 746 747 host->dma_desc_current = next->dma_desc; 748 host->dma_current = next->dma_chan; 749 next->dma_desc = NULL; 750 next->dma_chan = NULL; 751 } 752 753 static void mmci_pre_request(struct mmc_host *mmc, struct mmc_request *mrq) 754 { 755 struct mmci_host *host = mmc_priv(mmc); 756 struct mmc_data *data = mrq->data; 757 struct mmci_host_next *nd = &host->next_data; 758 759 if (!data) 760 return; 761 762 BUG_ON(data->host_cookie); 763 764 if (mmci_validate_data(host, data)) 765 return; 766 767 if (!mmci_dma_prep_next(host, data)) 768 data->host_cookie = ++nd->cookie < 0 ? 1 : nd->cookie; 769 } 770 771 static void mmci_post_request(struct mmc_host *mmc, struct mmc_request *mrq, 772 int err) 773 { 774 struct mmci_host *host = mmc_priv(mmc); 775 struct mmc_data *data = mrq->data; 776 777 if (!data || !data->host_cookie) 778 return; 779 780 mmci_dma_unmap(host, data); 781 782 if (err) { 783 struct mmci_host_next *next = &host->next_data; 784 struct dma_chan *chan; 785 if (data->flags & MMC_DATA_READ) 786 chan = host->dma_rx_channel; 787 else 788 chan = host->dma_tx_channel; 789 dmaengine_terminate_all(chan); 790 791 if (host->dma_desc_current == next->dma_desc) 792 host->dma_desc_current = NULL; 793 794 if (host->dma_current == next->dma_chan) { 795 host->dma_in_progress = false; 796 host->dma_current = NULL; 797 } 798 799 next->dma_desc = NULL; 800 next->dma_chan = NULL; 801 data->host_cookie = 0; 802 } 803 } 804 805 #else 806 /* Blank functions if the DMA engine is not available */ 807 static void mmci_get_next_data(struct mmci_host *host, struct mmc_data *data) 808 { 809 } 810 static inline void mmci_dma_setup(struct mmci_host *host) 811 { 812 } 813 814 static inline void mmci_dma_release(struct mmci_host *host) 815 { 816 } 817 818 static inline void mmci_dma_unmap(struct mmci_host *host, struct mmc_data *data) 819 { 820 } 821 822 static inline void mmci_dma_finalize(struct mmci_host *host, 823 struct mmc_data *data) 824 { 825 } 826 827 static inline void mmci_dma_data_error(struct mmci_host *host) 828 { 829 } 830 831 static inline int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl) 832 { 833 return -ENOSYS; 834 } 835 836 #define mmci_pre_request NULL 837 #define mmci_post_request NULL 838 839 #endif 840 841 static void mmci_start_data(struct mmci_host *host, struct mmc_data *data) 842 { 843 struct variant_data *variant = host->variant; 844 unsigned int datactrl, timeout, irqmask; 845 unsigned long long clks; 846 void __iomem *base; 847 int blksz_bits; 848 849 dev_dbg(mmc_dev(host->mmc), "blksz %04x blks %04x flags %08x\n", 850 data->blksz, data->blocks, data->flags); 851 852 host->data = data; 853 host->size = data->blksz * data->blocks; 854 data->bytes_xfered = 0; 855 856 clks = (unsigned long long)data->timeout_ns * host->cclk; 857 do_div(clks, NSEC_PER_SEC); 858 859 timeout = data->timeout_clks + (unsigned int)clks; 860 861 base = host->base; 862 writel(timeout, base + MMCIDATATIMER); 863 writel(host->size, base + MMCIDATALENGTH); 864 865 blksz_bits = ffs(data->blksz) - 1; 866 BUG_ON(1 << blksz_bits != data->blksz); 867 868 if (variant->blksz_datactrl16) 869 datactrl = MCI_DPSM_ENABLE | (data->blksz << 16); 870 else if (variant->blksz_datactrl4) 871 datactrl = MCI_DPSM_ENABLE | (data->blksz << 4); 872 else 873 datactrl = MCI_DPSM_ENABLE | blksz_bits << 4; 874 875 if (data->flags & MMC_DATA_READ) 876 datactrl |= MCI_DPSM_DIRECTION; 877 878 if (host->mmc->card && mmc_card_sdio(host->mmc->card)) { 879 u32 clk; 880 881 datactrl |= variant->datactrl_mask_sdio; 882 883 /* 884 * The ST Micro variant for SDIO small write transfers 885 * needs to have clock H/W flow control disabled, 886 * otherwise the transfer will not start. The threshold 887 * depends on the rate of MCLK. 888 */ 889 if (variant->st_sdio && data->flags & MMC_DATA_WRITE && 890 (host->size < 8 || 891 (host->size <= 8 && host->mclk > 50000000))) 892 clk = host->clk_reg & ~variant->clkreg_enable; 893 else 894 clk = host->clk_reg | variant->clkreg_enable; 895 896 mmci_write_clkreg(host, clk); 897 } 898 899 if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50 || 900 host->mmc->ios.timing == MMC_TIMING_MMC_DDR52) 901 datactrl |= variant->datactrl_mask_ddrmode; 902 903 /* 904 * Attempt to use DMA operation mode, if this 905 * should fail, fall back to PIO mode 906 */ 907 if (!mmci_dma_start_data(host, datactrl)) 908 return; 909 910 /* IRQ mode, map the SG list for CPU reading/writing */ 911 mmci_init_sg(host, data); 912 913 if (data->flags & MMC_DATA_READ) { 914 irqmask = MCI_RXFIFOHALFFULLMASK; 915 916 /* 917 * If we have less than the fifo 'half-full' threshold to 918 * transfer, trigger a PIO interrupt as soon as any data 919 * is available. 920 */ 921 if (host->size < variant->fifohalfsize) 922 irqmask |= MCI_RXDATAAVLBLMASK; 923 } else { 924 /* 925 * We don't actually need to include "FIFO empty" here 926 * since its implicit in "FIFO half empty". 927 */ 928 irqmask = MCI_TXFIFOHALFEMPTYMASK; 929 } 930 931 mmci_write_datactrlreg(host, datactrl); 932 writel(readl(base + MMCIMASK0) & ~MCI_DATAENDMASK, base + MMCIMASK0); 933 mmci_set_mask1(host, irqmask); 934 } 935 936 static void 937 mmci_start_command(struct mmci_host *host, struct mmc_command *cmd, u32 c) 938 { 939 void __iomem *base = host->base; 940 941 dev_dbg(mmc_dev(host->mmc), "op %02x arg %08x flags %08x\n", 942 cmd->opcode, cmd->arg, cmd->flags); 943 944 if (readl(base + MMCICOMMAND) & MCI_CPSM_ENABLE) { 945 writel(0, base + MMCICOMMAND); 946 mmci_reg_delay(host); 947 } 948 949 c |= cmd->opcode | MCI_CPSM_ENABLE; 950 if (cmd->flags & MMC_RSP_PRESENT) { 951 if (cmd->flags & MMC_RSP_136) 952 c |= MCI_CPSM_LONGRSP; 953 c |= MCI_CPSM_RESPONSE; 954 } 955 if (/*interrupt*/0) 956 c |= MCI_CPSM_INTERRUPT; 957 958 if (mmc_cmd_type(cmd) == MMC_CMD_ADTC) 959 c |= host->variant->data_cmd_enable; 960 961 host->cmd = cmd; 962 963 writel(cmd->arg, base + MMCIARGUMENT); 964 writel(c, base + MMCICOMMAND); 965 } 966 967 static void 968 mmci_data_irq(struct mmci_host *host, struct mmc_data *data, 969 unsigned int status) 970 { 971 /* Make sure we have data to handle */ 972 if (!data) 973 return; 974 975 /* First check for errors */ 976 if (status & (MCI_DATACRCFAIL | MCI_DATATIMEOUT | 977 host->variant->start_err | 978 MCI_TXUNDERRUN | MCI_RXOVERRUN)) { 979 u32 remain, success; 980 981 /* Terminate the DMA transfer */ 982 if (dma_inprogress(host)) { 983 mmci_dma_data_error(host); 984 mmci_dma_unmap(host, data); 985 } 986 987 /* 988 * Calculate how far we are into the transfer. Note that 989 * the data counter gives the number of bytes transferred 990 * on the MMC bus, not on the host side. On reads, this 991 * can be as much as a FIFO-worth of data ahead. This 992 * matters for FIFO overruns only. 993 */ 994 remain = readl(host->base + MMCIDATACNT); 995 success = data->blksz * data->blocks - remain; 996 997 dev_dbg(mmc_dev(host->mmc), "MCI ERROR IRQ, status 0x%08x at 0x%08x\n", 998 status, success); 999 if (status & MCI_DATACRCFAIL) { 1000 /* Last block was not successful */ 1001 success -= 1; 1002 data->error = -EILSEQ; 1003 } else if (status & MCI_DATATIMEOUT) { 1004 data->error = -ETIMEDOUT; 1005 } else if (status & MCI_STARTBITERR) { 1006 data->error = -ECOMM; 1007 } else if (status & MCI_TXUNDERRUN) { 1008 data->error = -EIO; 1009 } else if (status & MCI_RXOVERRUN) { 1010 if (success > host->variant->fifosize) 1011 success -= host->variant->fifosize; 1012 else 1013 success = 0; 1014 data->error = -EIO; 1015 } 1016 data->bytes_xfered = round_down(success, data->blksz); 1017 } 1018 1019 if (status & MCI_DATABLOCKEND) 1020 dev_err(mmc_dev(host->mmc), "stray MCI_DATABLOCKEND interrupt\n"); 1021 1022 if (status & MCI_DATAEND || data->error) { 1023 if (dma_inprogress(host)) 1024 mmci_dma_finalize(host, data); 1025 mmci_stop_data(host); 1026 1027 if (!data->error) 1028 /* The error clause is handled above, success! */ 1029 data->bytes_xfered = data->blksz * data->blocks; 1030 1031 if (!data->stop || host->mrq->sbc) { 1032 mmci_request_end(host, data->mrq); 1033 } else { 1034 mmci_start_command(host, data->stop, 0); 1035 } 1036 } 1037 } 1038 1039 static void 1040 mmci_cmd_irq(struct mmci_host *host, struct mmc_command *cmd, 1041 unsigned int status) 1042 { 1043 void __iomem *base = host->base; 1044 bool sbc; 1045 1046 if (!cmd) 1047 return; 1048 1049 sbc = (cmd == host->mrq->sbc); 1050 1051 /* 1052 * We need to be one of these interrupts to be considered worth 1053 * handling. Note that we tag on any latent IRQs postponed 1054 * due to waiting for busy status. 1055 */ 1056 if (!((status|host->busy_status) & 1057 (MCI_CMDCRCFAIL|MCI_CMDTIMEOUT|MCI_CMDSENT|MCI_CMDRESPEND))) 1058 return; 1059 1060 /* 1061 * ST Micro variant: handle busy detection. 1062 */ 1063 if (host->variant->busy_detect) { 1064 bool busy_resp = !!(cmd->flags & MMC_RSP_BUSY); 1065 1066 /* We are busy with a command, return */ 1067 if (host->busy_status && 1068 (status & host->variant->busy_detect_flag)) 1069 return; 1070 1071 /* 1072 * We were not busy, but we now got a busy response on 1073 * something that was not an error, and we double-check 1074 * that the special busy status bit is still set before 1075 * proceeding. 1076 */ 1077 if (!host->busy_status && busy_resp && 1078 !(status & (MCI_CMDCRCFAIL|MCI_CMDTIMEOUT)) && 1079 (readl(base + MMCISTATUS) & host->variant->busy_detect_flag)) { 1080 1081 /* Clear the busy start IRQ */ 1082 writel(host->variant->busy_detect_mask, 1083 host->base + MMCICLEAR); 1084 1085 /* Unmask the busy end IRQ */ 1086 writel(readl(base + MMCIMASK0) | 1087 host->variant->busy_detect_mask, 1088 base + MMCIMASK0); 1089 /* 1090 * Now cache the last response status code (until 1091 * the busy bit goes low), and return. 1092 */ 1093 host->busy_status = 1094 status & (MCI_CMDSENT|MCI_CMDRESPEND); 1095 return; 1096 } 1097 1098 /* 1099 * At this point we are not busy with a command, we have 1100 * not received a new busy request, clear and mask the busy 1101 * end IRQ and fall through to process the IRQ. 1102 */ 1103 if (host->busy_status) { 1104 1105 writel(host->variant->busy_detect_mask, 1106 host->base + MMCICLEAR); 1107 1108 writel(readl(base + MMCIMASK0) & 1109 ~host->variant->busy_detect_mask, 1110 base + MMCIMASK0); 1111 host->busy_status = 0; 1112 } 1113 } 1114 1115 host->cmd = NULL; 1116 1117 if (status & MCI_CMDTIMEOUT) { 1118 cmd->error = -ETIMEDOUT; 1119 } else if (status & MCI_CMDCRCFAIL && cmd->flags & MMC_RSP_CRC) { 1120 cmd->error = -EILSEQ; 1121 } else { 1122 cmd->resp[0] = readl(base + MMCIRESPONSE0); 1123 cmd->resp[1] = readl(base + MMCIRESPONSE1); 1124 cmd->resp[2] = readl(base + MMCIRESPONSE2); 1125 cmd->resp[3] = readl(base + MMCIRESPONSE3); 1126 } 1127 1128 if ((!sbc && !cmd->data) || cmd->error) { 1129 if (host->data) { 1130 /* Terminate the DMA transfer */ 1131 if (dma_inprogress(host)) { 1132 mmci_dma_data_error(host); 1133 mmci_dma_unmap(host, host->data); 1134 } 1135 mmci_stop_data(host); 1136 } 1137 mmci_request_end(host, host->mrq); 1138 } else if (sbc) { 1139 mmci_start_command(host, host->mrq->cmd, 0); 1140 } else if (!(cmd->data->flags & MMC_DATA_READ)) { 1141 mmci_start_data(host, cmd->data); 1142 } 1143 } 1144 1145 static int mmci_get_rx_fifocnt(struct mmci_host *host, u32 status, int remain) 1146 { 1147 return remain - (readl(host->base + MMCIFIFOCNT) << 2); 1148 } 1149 1150 static int mmci_qcom_get_rx_fifocnt(struct mmci_host *host, u32 status, int r) 1151 { 1152 /* 1153 * on qcom SDCC4 only 8 words are used in each burst so only 8 addresses 1154 * from the fifo range should be used 1155 */ 1156 if (status & MCI_RXFIFOHALFFULL) 1157 return host->variant->fifohalfsize; 1158 else if (status & MCI_RXDATAAVLBL) 1159 return 4; 1160 1161 return 0; 1162 } 1163 1164 static int mmci_pio_read(struct mmci_host *host, char *buffer, unsigned int remain) 1165 { 1166 void __iomem *base = host->base; 1167 char *ptr = buffer; 1168 u32 status = readl(host->base + MMCISTATUS); 1169 int host_remain = host->size; 1170 1171 do { 1172 int count = host->get_rx_fifocnt(host, status, host_remain); 1173 1174 if (count > remain) 1175 count = remain; 1176 1177 if (count <= 0) 1178 break; 1179 1180 /* 1181 * SDIO especially may want to send something that is 1182 * not divisible by 4 (as opposed to card sectors 1183 * etc). Therefore make sure to always read the last bytes 1184 * while only doing full 32-bit reads towards the FIFO. 1185 */ 1186 if (unlikely(count & 0x3)) { 1187 if (count < 4) { 1188 unsigned char buf[4]; 1189 ioread32_rep(base + MMCIFIFO, buf, 1); 1190 memcpy(ptr, buf, count); 1191 } else { 1192 ioread32_rep(base + MMCIFIFO, ptr, count >> 2); 1193 count &= ~0x3; 1194 } 1195 } else { 1196 ioread32_rep(base + MMCIFIFO, ptr, count >> 2); 1197 } 1198 1199 ptr += count; 1200 remain -= count; 1201 host_remain -= count; 1202 1203 if (remain == 0) 1204 break; 1205 1206 status = readl(base + MMCISTATUS); 1207 } while (status & MCI_RXDATAAVLBL); 1208 1209 return ptr - buffer; 1210 } 1211 1212 static int mmci_pio_write(struct mmci_host *host, char *buffer, unsigned int remain, u32 status) 1213 { 1214 struct variant_data *variant = host->variant; 1215 void __iomem *base = host->base; 1216 char *ptr = buffer; 1217 1218 do { 1219 unsigned int count, maxcnt; 1220 1221 maxcnt = status & MCI_TXFIFOEMPTY ? 1222 variant->fifosize : variant->fifohalfsize; 1223 count = min(remain, maxcnt); 1224 1225 /* 1226 * SDIO especially may want to send something that is 1227 * not divisible by 4 (as opposed to card sectors 1228 * etc), and the FIFO only accept full 32-bit writes. 1229 * So compensate by adding +3 on the count, a single 1230 * byte become a 32bit write, 7 bytes will be two 1231 * 32bit writes etc. 1232 */ 1233 iowrite32_rep(base + MMCIFIFO, ptr, (count + 3) >> 2); 1234 1235 ptr += count; 1236 remain -= count; 1237 1238 if (remain == 0) 1239 break; 1240 1241 status = readl(base + MMCISTATUS); 1242 } while (status & MCI_TXFIFOHALFEMPTY); 1243 1244 return ptr - buffer; 1245 } 1246 1247 /* 1248 * PIO data transfer IRQ handler. 1249 */ 1250 static irqreturn_t mmci_pio_irq(int irq, void *dev_id) 1251 { 1252 struct mmci_host *host = dev_id; 1253 struct sg_mapping_iter *sg_miter = &host->sg_miter; 1254 struct variant_data *variant = host->variant; 1255 void __iomem *base = host->base; 1256 unsigned long flags; 1257 u32 status; 1258 1259 status = readl(base + MMCISTATUS); 1260 1261 dev_dbg(mmc_dev(host->mmc), "irq1 (pio) %08x\n", status); 1262 1263 local_irq_save(flags); 1264 1265 do { 1266 unsigned int remain, len; 1267 char *buffer; 1268 1269 /* 1270 * For write, we only need to test the half-empty flag 1271 * here - if the FIFO is completely empty, then by 1272 * definition it is more than half empty. 1273 * 1274 * For read, check for data available. 1275 */ 1276 if (!(status & (MCI_TXFIFOHALFEMPTY|MCI_RXDATAAVLBL))) 1277 break; 1278 1279 if (!sg_miter_next(sg_miter)) 1280 break; 1281 1282 buffer = sg_miter->addr; 1283 remain = sg_miter->length; 1284 1285 len = 0; 1286 if (status & MCI_RXACTIVE) 1287 len = mmci_pio_read(host, buffer, remain); 1288 if (status & MCI_TXACTIVE) 1289 len = mmci_pio_write(host, buffer, remain, status); 1290 1291 sg_miter->consumed = len; 1292 1293 host->size -= len; 1294 remain -= len; 1295 1296 if (remain) 1297 break; 1298 1299 status = readl(base + MMCISTATUS); 1300 } while (1); 1301 1302 sg_miter_stop(sg_miter); 1303 1304 local_irq_restore(flags); 1305 1306 /* 1307 * If we have less than the fifo 'half-full' threshold to transfer, 1308 * trigger a PIO interrupt as soon as any data is available. 1309 */ 1310 if (status & MCI_RXACTIVE && host->size < variant->fifohalfsize) 1311 mmci_set_mask1(host, MCI_RXDATAAVLBLMASK); 1312 1313 /* 1314 * If we run out of data, disable the data IRQs; this 1315 * prevents a race where the FIFO becomes empty before 1316 * the chip itself has disabled the data path, and 1317 * stops us racing with our data end IRQ. 1318 */ 1319 if (host->size == 0) { 1320 mmci_set_mask1(host, 0); 1321 writel(readl(base + MMCIMASK0) | MCI_DATAENDMASK, base + MMCIMASK0); 1322 } 1323 1324 return IRQ_HANDLED; 1325 } 1326 1327 /* 1328 * Handle completion of command and data transfers. 1329 */ 1330 static irqreturn_t mmci_irq(int irq, void *dev_id) 1331 { 1332 struct mmci_host *host = dev_id; 1333 u32 status; 1334 int ret = 0; 1335 1336 spin_lock(&host->lock); 1337 1338 do { 1339 status = readl(host->base + MMCISTATUS); 1340 1341 if (host->singleirq) { 1342 if (status & host->mask1_reg) 1343 mmci_pio_irq(irq, dev_id); 1344 1345 status &= ~MCI_IRQ1MASK; 1346 } 1347 1348 /* 1349 * We intentionally clear the MCI_ST_CARDBUSY IRQ (if it's 1350 * enabled) in mmci_cmd_irq() function where ST Micro busy 1351 * detection variant is handled. Considering the HW seems to be 1352 * triggering the IRQ on both edges while monitoring DAT0 for 1353 * busy completion and that same status bit is used to monitor 1354 * start and end of busy detection, special care must be taken 1355 * to make sure that both start and end interrupts are always 1356 * cleared one after the other. 1357 */ 1358 status &= readl(host->base + MMCIMASK0); 1359 if (host->variant->busy_detect) 1360 writel(status & ~host->variant->busy_detect_mask, 1361 host->base + MMCICLEAR); 1362 else 1363 writel(status, host->base + MMCICLEAR); 1364 1365 dev_dbg(mmc_dev(host->mmc), "irq0 (data+cmd) %08x\n", status); 1366 1367 if (host->variant->reversed_irq_handling) { 1368 mmci_data_irq(host, host->data, status); 1369 mmci_cmd_irq(host, host->cmd, status); 1370 } else { 1371 mmci_cmd_irq(host, host->cmd, status); 1372 mmci_data_irq(host, host->data, status); 1373 } 1374 1375 /* 1376 * Don't poll for busy completion in irq context. 1377 */ 1378 if (host->variant->busy_detect && host->busy_status) 1379 status &= ~host->variant->busy_detect_flag; 1380 1381 ret = 1; 1382 } while (status); 1383 1384 spin_unlock(&host->lock); 1385 1386 return IRQ_RETVAL(ret); 1387 } 1388 1389 static void mmci_request(struct mmc_host *mmc, struct mmc_request *mrq) 1390 { 1391 struct mmci_host *host = mmc_priv(mmc); 1392 unsigned long flags; 1393 1394 WARN_ON(host->mrq != NULL); 1395 1396 mrq->cmd->error = mmci_validate_data(host, mrq->data); 1397 if (mrq->cmd->error) { 1398 mmc_request_done(mmc, mrq); 1399 return; 1400 } 1401 1402 spin_lock_irqsave(&host->lock, flags); 1403 1404 host->mrq = mrq; 1405 1406 if (mrq->data) 1407 mmci_get_next_data(host, mrq->data); 1408 1409 if (mrq->data && mrq->data->flags & MMC_DATA_READ) 1410 mmci_start_data(host, mrq->data); 1411 1412 if (mrq->sbc) 1413 mmci_start_command(host, mrq->sbc, 0); 1414 else 1415 mmci_start_command(host, mrq->cmd, 0); 1416 1417 spin_unlock_irqrestore(&host->lock, flags); 1418 } 1419 1420 static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) 1421 { 1422 struct mmci_host *host = mmc_priv(mmc); 1423 struct variant_data *variant = host->variant; 1424 u32 pwr = 0; 1425 unsigned long flags; 1426 int ret; 1427 1428 if (host->plat->ios_handler && 1429 host->plat->ios_handler(mmc_dev(mmc), ios)) 1430 dev_err(mmc_dev(mmc), "platform ios_handler failed\n"); 1431 1432 switch (ios->power_mode) { 1433 case MMC_POWER_OFF: 1434 if (!IS_ERR(mmc->supply.vmmc)) 1435 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0); 1436 1437 if (!IS_ERR(mmc->supply.vqmmc) && host->vqmmc_enabled) { 1438 regulator_disable(mmc->supply.vqmmc); 1439 host->vqmmc_enabled = false; 1440 } 1441 1442 break; 1443 case MMC_POWER_UP: 1444 if (!IS_ERR(mmc->supply.vmmc)) 1445 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd); 1446 1447 /* 1448 * The ST Micro variant doesn't have the PL180s MCI_PWR_UP 1449 * and instead uses MCI_PWR_ON so apply whatever value is 1450 * configured in the variant data. 1451 */ 1452 pwr |= variant->pwrreg_powerup; 1453 1454 break; 1455 case MMC_POWER_ON: 1456 if (!IS_ERR(mmc->supply.vqmmc) && !host->vqmmc_enabled) { 1457 ret = regulator_enable(mmc->supply.vqmmc); 1458 if (ret < 0) 1459 dev_err(mmc_dev(mmc), 1460 "failed to enable vqmmc regulator\n"); 1461 else 1462 host->vqmmc_enabled = true; 1463 } 1464 1465 pwr |= MCI_PWR_ON; 1466 break; 1467 } 1468 1469 if (variant->signal_direction && ios->power_mode != MMC_POWER_OFF) { 1470 /* 1471 * The ST Micro variant has some additional bits 1472 * indicating signal direction for the signals in 1473 * the SD/MMC bus and feedback-clock usage. 1474 */ 1475 pwr |= host->pwr_reg_add; 1476 1477 if (ios->bus_width == MMC_BUS_WIDTH_4) 1478 pwr &= ~MCI_ST_DATA74DIREN; 1479 else if (ios->bus_width == MMC_BUS_WIDTH_1) 1480 pwr &= (~MCI_ST_DATA74DIREN & 1481 ~MCI_ST_DATA31DIREN & 1482 ~MCI_ST_DATA2DIREN); 1483 } 1484 1485 if (variant->opendrain) { 1486 if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) 1487 pwr |= variant->opendrain; 1488 } else { 1489 /* 1490 * If the variant cannot configure the pads by its own, then we 1491 * expect the pinctrl to be able to do that for us 1492 */ 1493 if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) 1494 pinctrl_select_state(host->pinctrl, host->pins_opendrain); 1495 else 1496 pinctrl_select_state(host->pinctrl, host->pins_default); 1497 } 1498 1499 /* 1500 * If clock = 0 and the variant requires the MMCIPOWER to be used for 1501 * gating the clock, the MCI_PWR_ON bit is cleared. 1502 */ 1503 if (!ios->clock && variant->pwrreg_clkgate) 1504 pwr &= ~MCI_PWR_ON; 1505 1506 if (host->variant->explicit_mclk_control && 1507 ios->clock != host->clock_cache) { 1508 ret = clk_set_rate(host->clk, ios->clock); 1509 if (ret < 0) 1510 dev_err(mmc_dev(host->mmc), 1511 "Error setting clock rate (%d)\n", ret); 1512 else 1513 host->mclk = clk_get_rate(host->clk); 1514 } 1515 host->clock_cache = ios->clock; 1516 1517 spin_lock_irqsave(&host->lock, flags); 1518 1519 mmci_set_clkreg(host, ios->clock); 1520 mmci_write_pwrreg(host, pwr); 1521 mmci_reg_delay(host); 1522 1523 spin_unlock_irqrestore(&host->lock, flags); 1524 } 1525 1526 static int mmci_get_cd(struct mmc_host *mmc) 1527 { 1528 struct mmci_host *host = mmc_priv(mmc); 1529 struct mmci_platform_data *plat = host->plat; 1530 unsigned int status = mmc_gpio_get_cd(mmc); 1531 1532 if (status == -ENOSYS) { 1533 if (!plat->status) 1534 return 1; /* Assume always present */ 1535 1536 status = plat->status(mmc_dev(host->mmc)); 1537 } 1538 return status; 1539 } 1540 1541 static int mmci_sig_volt_switch(struct mmc_host *mmc, struct mmc_ios *ios) 1542 { 1543 int ret = 0; 1544 1545 if (!IS_ERR(mmc->supply.vqmmc)) { 1546 1547 switch (ios->signal_voltage) { 1548 case MMC_SIGNAL_VOLTAGE_330: 1549 ret = regulator_set_voltage(mmc->supply.vqmmc, 1550 2700000, 3600000); 1551 break; 1552 case MMC_SIGNAL_VOLTAGE_180: 1553 ret = regulator_set_voltage(mmc->supply.vqmmc, 1554 1700000, 1950000); 1555 break; 1556 case MMC_SIGNAL_VOLTAGE_120: 1557 ret = regulator_set_voltage(mmc->supply.vqmmc, 1558 1100000, 1300000); 1559 break; 1560 } 1561 1562 if (ret) 1563 dev_warn(mmc_dev(mmc), "Voltage switch failed\n"); 1564 } 1565 1566 return ret; 1567 } 1568 1569 static struct mmc_host_ops mmci_ops = { 1570 .request = mmci_request, 1571 .pre_req = mmci_pre_request, 1572 .post_req = mmci_post_request, 1573 .set_ios = mmci_set_ios, 1574 .get_ro = mmc_gpio_get_ro, 1575 .get_cd = mmci_get_cd, 1576 .start_signal_voltage_switch = mmci_sig_volt_switch, 1577 }; 1578 1579 static int mmci_of_parse(struct device_node *np, struct mmc_host *mmc) 1580 { 1581 struct mmci_host *host = mmc_priv(mmc); 1582 int ret = mmc_of_parse(mmc); 1583 1584 if (ret) 1585 return ret; 1586 1587 if (of_get_property(np, "st,sig-dir-dat0", NULL)) 1588 host->pwr_reg_add |= MCI_ST_DATA0DIREN; 1589 if (of_get_property(np, "st,sig-dir-dat2", NULL)) 1590 host->pwr_reg_add |= MCI_ST_DATA2DIREN; 1591 if (of_get_property(np, "st,sig-dir-dat31", NULL)) 1592 host->pwr_reg_add |= MCI_ST_DATA31DIREN; 1593 if (of_get_property(np, "st,sig-dir-dat74", NULL)) 1594 host->pwr_reg_add |= MCI_ST_DATA74DIREN; 1595 if (of_get_property(np, "st,sig-dir-cmd", NULL)) 1596 host->pwr_reg_add |= MCI_ST_CMDDIREN; 1597 if (of_get_property(np, "st,sig-pin-fbclk", NULL)) 1598 host->pwr_reg_add |= MCI_ST_FBCLKEN; 1599 1600 if (of_get_property(np, "mmc-cap-mmc-highspeed", NULL)) 1601 mmc->caps |= MMC_CAP_MMC_HIGHSPEED; 1602 if (of_get_property(np, "mmc-cap-sd-highspeed", NULL)) 1603 mmc->caps |= MMC_CAP_SD_HIGHSPEED; 1604 1605 return 0; 1606 } 1607 1608 static int mmci_probe(struct amba_device *dev, 1609 const struct amba_id *id) 1610 { 1611 struct mmci_platform_data *plat = dev->dev.platform_data; 1612 struct device_node *np = dev->dev.of_node; 1613 struct variant_data *variant = id->data; 1614 struct mmci_host *host; 1615 struct mmc_host *mmc; 1616 int ret; 1617 1618 /* Must have platform data or Device Tree. */ 1619 if (!plat && !np) { 1620 dev_err(&dev->dev, "No plat data or DT found\n"); 1621 return -EINVAL; 1622 } 1623 1624 if (!plat) { 1625 plat = devm_kzalloc(&dev->dev, sizeof(*plat), GFP_KERNEL); 1626 if (!plat) 1627 return -ENOMEM; 1628 } 1629 1630 mmc = mmc_alloc_host(sizeof(struct mmci_host), &dev->dev); 1631 if (!mmc) 1632 return -ENOMEM; 1633 1634 ret = mmci_of_parse(np, mmc); 1635 if (ret) 1636 goto host_free; 1637 1638 host = mmc_priv(mmc); 1639 host->mmc = mmc; 1640 1641 /* 1642 * Some variant (STM32) doesn't have opendrain bit, nevertheless 1643 * pins can be set accordingly using pinctrl 1644 */ 1645 if (!variant->opendrain) { 1646 host->pinctrl = devm_pinctrl_get(&dev->dev); 1647 if (IS_ERR(host->pinctrl)) { 1648 dev_err(&dev->dev, "failed to get pinctrl"); 1649 ret = PTR_ERR(host->pinctrl); 1650 goto host_free; 1651 } 1652 1653 host->pins_default = pinctrl_lookup_state(host->pinctrl, 1654 PINCTRL_STATE_DEFAULT); 1655 if (IS_ERR(host->pins_default)) { 1656 dev_err(mmc_dev(mmc), "Can't select default pins\n"); 1657 ret = PTR_ERR(host->pins_default); 1658 goto host_free; 1659 } 1660 1661 host->pins_opendrain = pinctrl_lookup_state(host->pinctrl, 1662 MMCI_PINCTRL_STATE_OPENDRAIN); 1663 if (IS_ERR(host->pins_opendrain)) { 1664 dev_err(mmc_dev(mmc), "Can't select opendrain pins\n"); 1665 ret = PTR_ERR(host->pins_opendrain); 1666 goto host_free; 1667 } 1668 } 1669 1670 host->hw_designer = amba_manf(dev); 1671 host->hw_revision = amba_rev(dev); 1672 dev_dbg(mmc_dev(mmc), "designer ID = 0x%02x\n", host->hw_designer); 1673 dev_dbg(mmc_dev(mmc), "revision = 0x%01x\n", host->hw_revision); 1674 1675 host->clk = devm_clk_get(&dev->dev, NULL); 1676 if (IS_ERR(host->clk)) { 1677 ret = PTR_ERR(host->clk); 1678 goto host_free; 1679 } 1680 1681 ret = clk_prepare_enable(host->clk); 1682 if (ret) 1683 goto host_free; 1684 1685 if (variant->qcom_fifo) 1686 host->get_rx_fifocnt = mmci_qcom_get_rx_fifocnt; 1687 else 1688 host->get_rx_fifocnt = mmci_get_rx_fifocnt; 1689 1690 host->plat = plat; 1691 host->variant = variant; 1692 host->mclk = clk_get_rate(host->clk); 1693 /* 1694 * According to the spec, mclk is max 100 MHz, 1695 * so we try to adjust the clock down to this, 1696 * (if possible). 1697 */ 1698 if (host->mclk > variant->f_max) { 1699 ret = clk_set_rate(host->clk, variant->f_max); 1700 if (ret < 0) 1701 goto clk_disable; 1702 host->mclk = clk_get_rate(host->clk); 1703 dev_dbg(mmc_dev(mmc), "eventual mclk rate: %u Hz\n", 1704 host->mclk); 1705 } 1706 1707 host->phybase = dev->res.start; 1708 host->base = devm_ioremap_resource(&dev->dev, &dev->res); 1709 if (IS_ERR(host->base)) { 1710 ret = PTR_ERR(host->base); 1711 goto clk_disable; 1712 } 1713 1714 /* 1715 * The ARM and ST versions of the block have slightly different 1716 * clock divider equations which means that the minimum divider 1717 * differs too. 1718 * on Qualcomm like controllers get the nearest minimum clock to 100Khz 1719 */ 1720 if (variant->st_clkdiv) 1721 mmc->f_min = DIV_ROUND_UP(host->mclk, 257); 1722 else if (variant->explicit_mclk_control) 1723 mmc->f_min = clk_round_rate(host->clk, 100000); 1724 else 1725 mmc->f_min = DIV_ROUND_UP(host->mclk, 512); 1726 /* 1727 * If no maximum operating frequency is supplied, fall back to use 1728 * the module parameter, which has a (low) default value in case it 1729 * is not specified. Either value must not exceed the clock rate into 1730 * the block, of course. 1731 */ 1732 if (mmc->f_max) 1733 mmc->f_max = variant->explicit_mclk_control ? 1734 min(variant->f_max, mmc->f_max) : 1735 min(host->mclk, mmc->f_max); 1736 else 1737 mmc->f_max = variant->explicit_mclk_control ? 1738 fmax : min(host->mclk, fmax); 1739 1740 1741 dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max); 1742 1743 /* Get regulators and the supported OCR mask */ 1744 ret = mmc_regulator_get_supply(mmc); 1745 if (ret) 1746 goto clk_disable; 1747 1748 if (!mmc->ocr_avail) 1749 mmc->ocr_avail = plat->ocr_mask; 1750 else if (plat->ocr_mask) 1751 dev_warn(mmc_dev(mmc), "Platform OCR mask is ignored\n"); 1752 1753 /* DT takes precedence over platform data. */ 1754 if (!np) { 1755 if (!plat->cd_invert) 1756 mmc->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH; 1757 mmc->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH; 1758 } 1759 1760 /* We support these capabilities. */ 1761 mmc->caps |= MMC_CAP_CMD23; 1762 1763 /* 1764 * Enable busy detection. 1765 */ 1766 if (variant->busy_detect) { 1767 mmci_ops.card_busy = mmci_card_busy; 1768 /* 1769 * Not all variants have a flag to enable busy detection 1770 * in the DPSM, but if they do, set it here. 1771 */ 1772 if (variant->busy_dpsm_flag) 1773 mmci_write_datactrlreg(host, 1774 host->variant->busy_dpsm_flag); 1775 mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY; 1776 mmc->max_busy_timeout = 0; 1777 } 1778 1779 mmc->ops = &mmci_ops; 1780 1781 /* We support these PM capabilities. */ 1782 mmc->pm_caps |= MMC_PM_KEEP_POWER; 1783 1784 /* 1785 * We can do SGIO 1786 */ 1787 mmc->max_segs = NR_SG; 1788 1789 /* 1790 * Since only a certain number of bits are valid in the data length 1791 * register, we must ensure that we don't exceed 2^num-1 bytes in a 1792 * single request. 1793 */ 1794 mmc->max_req_size = (1 << variant->datalength_bits) - 1; 1795 1796 /* 1797 * Set the maximum segment size. Since we aren't doing DMA 1798 * (yet) we are only limited by the data length register. 1799 */ 1800 mmc->max_seg_size = mmc->max_req_size; 1801 1802 /* 1803 * Block size can be up to 2048 bytes, but must be a power of two. 1804 */ 1805 mmc->max_blk_size = 1 << 11; 1806 1807 /* 1808 * Limit the number of blocks transferred so that we don't overflow 1809 * the maximum request size. 1810 */ 1811 mmc->max_blk_count = mmc->max_req_size >> 11; 1812 1813 spin_lock_init(&host->lock); 1814 1815 writel(0, host->base + MMCIMASK0); 1816 1817 if (variant->mmcimask1) 1818 writel(0, host->base + MMCIMASK1); 1819 1820 writel(0xfff, host->base + MMCICLEAR); 1821 1822 /* 1823 * If: 1824 * - not using DT but using a descriptor table, or 1825 * - using a table of descriptors ALONGSIDE DT, or 1826 * look up these descriptors named "cd" and "wp" right here, fail 1827 * silently of these do not exist and proceed to try platform data 1828 */ 1829 if (!np) { 1830 ret = mmc_gpiod_request_cd(mmc, "cd", 0, false, 0, NULL); 1831 if (ret < 0) { 1832 if (ret == -EPROBE_DEFER) 1833 goto clk_disable; 1834 else if (gpio_is_valid(plat->gpio_cd)) { 1835 ret = mmc_gpio_request_cd(mmc, plat->gpio_cd, 0); 1836 if (ret) 1837 goto clk_disable; 1838 } 1839 } 1840 1841 ret = mmc_gpiod_request_ro(mmc, "wp", 0, false, 0, NULL); 1842 if (ret < 0) { 1843 if (ret == -EPROBE_DEFER) 1844 goto clk_disable; 1845 else if (gpio_is_valid(plat->gpio_wp)) { 1846 ret = mmc_gpio_request_ro(mmc, plat->gpio_wp); 1847 if (ret) 1848 goto clk_disable; 1849 } 1850 } 1851 } 1852 1853 ret = devm_request_irq(&dev->dev, dev->irq[0], mmci_irq, IRQF_SHARED, 1854 DRIVER_NAME " (cmd)", host); 1855 if (ret) 1856 goto clk_disable; 1857 1858 if (!dev->irq[1]) 1859 host->singleirq = true; 1860 else { 1861 ret = devm_request_irq(&dev->dev, dev->irq[1], mmci_pio_irq, 1862 IRQF_SHARED, DRIVER_NAME " (pio)", host); 1863 if (ret) 1864 goto clk_disable; 1865 } 1866 1867 writel(MCI_IRQENABLE, host->base + MMCIMASK0); 1868 1869 amba_set_drvdata(dev, mmc); 1870 1871 dev_info(&dev->dev, "%s: PL%03x manf %x rev%u at 0x%08llx irq %d,%d (pio)\n", 1872 mmc_hostname(mmc), amba_part(dev), amba_manf(dev), 1873 amba_rev(dev), (unsigned long long)dev->res.start, 1874 dev->irq[0], dev->irq[1]); 1875 1876 mmci_dma_setup(host); 1877 1878 pm_runtime_set_autosuspend_delay(&dev->dev, 50); 1879 pm_runtime_use_autosuspend(&dev->dev); 1880 1881 mmc_add_host(mmc); 1882 1883 pm_runtime_put(&dev->dev); 1884 return 0; 1885 1886 clk_disable: 1887 clk_disable_unprepare(host->clk); 1888 host_free: 1889 mmc_free_host(mmc); 1890 return ret; 1891 } 1892 1893 static int mmci_remove(struct amba_device *dev) 1894 { 1895 struct mmc_host *mmc = amba_get_drvdata(dev); 1896 1897 if (mmc) { 1898 struct mmci_host *host = mmc_priv(mmc); 1899 struct variant_data *variant = host->variant; 1900 1901 /* 1902 * Undo pm_runtime_put() in probe. We use the _sync 1903 * version here so that we can access the primecell. 1904 */ 1905 pm_runtime_get_sync(&dev->dev); 1906 1907 mmc_remove_host(mmc); 1908 1909 writel(0, host->base + MMCIMASK0); 1910 1911 if (variant->mmcimask1) 1912 writel(0, host->base + MMCIMASK1); 1913 1914 writel(0, host->base + MMCICOMMAND); 1915 writel(0, host->base + MMCIDATACTRL); 1916 1917 mmci_dma_release(host); 1918 clk_disable_unprepare(host->clk); 1919 mmc_free_host(mmc); 1920 } 1921 1922 return 0; 1923 } 1924 1925 #ifdef CONFIG_PM 1926 static void mmci_save(struct mmci_host *host) 1927 { 1928 unsigned long flags; 1929 1930 spin_lock_irqsave(&host->lock, flags); 1931 1932 writel(0, host->base + MMCIMASK0); 1933 if (host->variant->pwrreg_nopower) { 1934 writel(0, host->base + MMCIDATACTRL); 1935 writel(0, host->base + MMCIPOWER); 1936 writel(0, host->base + MMCICLOCK); 1937 } 1938 mmci_reg_delay(host); 1939 1940 spin_unlock_irqrestore(&host->lock, flags); 1941 } 1942 1943 static void mmci_restore(struct mmci_host *host) 1944 { 1945 unsigned long flags; 1946 1947 spin_lock_irqsave(&host->lock, flags); 1948 1949 if (host->variant->pwrreg_nopower) { 1950 writel(host->clk_reg, host->base + MMCICLOCK); 1951 writel(host->datactrl_reg, host->base + MMCIDATACTRL); 1952 writel(host->pwr_reg, host->base + MMCIPOWER); 1953 } 1954 writel(MCI_IRQENABLE, host->base + MMCIMASK0); 1955 mmci_reg_delay(host); 1956 1957 spin_unlock_irqrestore(&host->lock, flags); 1958 } 1959 1960 static int mmci_runtime_suspend(struct device *dev) 1961 { 1962 struct amba_device *adev = to_amba_device(dev); 1963 struct mmc_host *mmc = amba_get_drvdata(adev); 1964 1965 if (mmc) { 1966 struct mmci_host *host = mmc_priv(mmc); 1967 pinctrl_pm_select_sleep_state(dev); 1968 mmci_save(host); 1969 clk_disable_unprepare(host->clk); 1970 } 1971 1972 return 0; 1973 } 1974 1975 static int mmci_runtime_resume(struct device *dev) 1976 { 1977 struct amba_device *adev = to_amba_device(dev); 1978 struct mmc_host *mmc = amba_get_drvdata(adev); 1979 1980 if (mmc) { 1981 struct mmci_host *host = mmc_priv(mmc); 1982 clk_prepare_enable(host->clk); 1983 mmci_restore(host); 1984 pinctrl_pm_select_default_state(dev); 1985 } 1986 1987 return 0; 1988 } 1989 #endif 1990 1991 static const struct dev_pm_ops mmci_dev_pm_ops = { 1992 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, 1993 pm_runtime_force_resume) 1994 SET_RUNTIME_PM_OPS(mmci_runtime_suspend, mmci_runtime_resume, NULL) 1995 }; 1996 1997 static const struct amba_id mmci_ids[] = { 1998 { 1999 .id = 0x00041180, 2000 .mask = 0xff0fffff, 2001 .data = &variant_arm, 2002 }, 2003 { 2004 .id = 0x01041180, 2005 .mask = 0xff0fffff, 2006 .data = &variant_arm_extended_fifo, 2007 }, 2008 { 2009 .id = 0x02041180, 2010 .mask = 0xff0fffff, 2011 .data = &variant_arm_extended_fifo_hwfc, 2012 }, 2013 { 2014 .id = 0x00041181, 2015 .mask = 0x000fffff, 2016 .data = &variant_arm, 2017 }, 2018 /* ST Micro variants */ 2019 { 2020 .id = 0x00180180, 2021 .mask = 0x00ffffff, 2022 .data = &variant_u300, 2023 }, 2024 { 2025 .id = 0x10180180, 2026 .mask = 0xf0ffffff, 2027 .data = &variant_nomadik, 2028 }, 2029 { 2030 .id = 0x00280180, 2031 .mask = 0x00ffffff, 2032 .data = &variant_nomadik, 2033 }, 2034 { 2035 .id = 0x00480180, 2036 .mask = 0xf0ffffff, 2037 .data = &variant_ux500, 2038 }, 2039 { 2040 .id = 0x10480180, 2041 .mask = 0xf0ffffff, 2042 .data = &variant_ux500v2, 2043 }, 2044 { 2045 .id = 0x00880180, 2046 .mask = 0x00ffffff, 2047 .data = &variant_stm32, 2048 }, 2049 /* Qualcomm variants */ 2050 { 2051 .id = 0x00051180, 2052 .mask = 0x000fffff, 2053 .data = &variant_qcom, 2054 }, 2055 { 0, 0 }, 2056 }; 2057 2058 MODULE_DEVICE_TABLE(amba, mmci_ids); 2059 2060 static struct amba_driver mmci_driver = { 2061 .drv = { 2062 .name = DRIVER_NAME, 2063 .pm = &mmci_dev_pm_ops, 2064 }, 2065 .probe = mmci_probe, 2066 .remove = mmci_remove, 2067 .id_table = mmci_ids, 2068 }; 2069 2070 module_amba_driver(mmci_driver); 2071 2072 module_param(fmax, uint, 0444); 2073 2074 MODULE_DESCRIPTION("ARM PrimeCell PL180/181 Multimedia Card Interface driver"); 2075 MODULE_LICENSE("GPL"); 2076