1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * LiteX LiteSDCard driver 4 * 5 * Copyright (C) 2019-2020 Antmicro <contact@antmicro.com> 6 * Copyright (C) 2019-2020 Kamil Rakoczy <krakoczy@antmicro.com> 7 * Copyright (C) 2019-2020 Maciej Dudek <mdudek@internships.antmicro.com> 8 * Copyright (C) 2020 Paul Mackerras <paulus@ozlabs.org> 9 * Copyright (C) 2020-2022 Gabriel Somlo <gsomlo@gmail.com> 10 */ 11 12 #include <linux/bits.h> 13 #include <linux/clk.h> 14 #include <linux/delay.h> 15 #include <linux/dma-mapping.h> 16 #include <linux/interrupt.h> 17 #include <linux/iopoll.h> 18 #include <linux/litex.h> 19 #include <linux/mod_devicetable.h> 20 #include <linux/module.h> 21 #include <linux/platform_device.h> 22 23 #include <linux/mmc/host.h> 24 #include <linux/mmc/mmc.h> 25 #include <linux/mmc/sd.h> 26 27 #define LITEX_PHY_CARDDETECT 0x00 28 #define LITEX_PHY_CLOCKERDIV 0x04 29 #define LITEX_PHY_INITIALIZE 0x08 30 #define LITEX_PHY_WRITESTATUS 0x0C 31 #define LITEX_CORE_CMDARG 0x00 32 #define LITEX_CORE_CMDCMD 0x04 33 #define LITEX_CORE_CMDSND 0x08 34 #define LITEX_CORE_CMDRSP 0x0C 35 #define LITEX_CORE_CMDEVT 0x1C 36 #define LITEX_CORE_DATEVT 0x20 37 #define LITEX_CORE_BLKLEN 0x24 38 #define LITEX_CORE_BLKCNT 0x28 39 #define LITEX_BLK2MEM_BASE 0x00 40 #define LITEX_BLK2MEM_LEN 0x08 41 #define LITEX_BLK2MEM_ENA 0x0C 42 #define LITEX_BLK2MEM_DONE 0x10 43 #define LITEX_BLK2MEM_LOOP 0x14 44 #define LITEX_MEM2BLK_BASE 0x00 45 #define LITEX_MEM2BLK_LEN 0x08 46 #define LITEX_MEM2BLK_ENA 0x0C 47 #define LITEX_MEM2BLK_DONE 0x10 48 #define LITEX_MEM2BLK_LOOP 0x14 49 #define LITEX_MEM2BLK 0x18 50 #define LITEX_IRQ_STATUS 0x00 51 #define LITEX_IRQ_PENDING 0x04 52 #define LITEX_IRQ_ENABLE 0x08 53 54 #define SD_CTL_DATA_XFER_NONE 0 55 #define SD_CTL_DATA_XFER_READ 1 56 #define SD_CTL_DATA_XFER_WRITE 2 57 58 #define SD_CTL_RESP_NONE 0 59 #define SD_CTL_RESP_SHORT 1 60 #define SD_CTL_RESP_LONG 2 61 #define SD_CTL_RESP_SHORT_BUSY 3 62 63 #define SD_BIT_DONE BIT(0) 64 #define SD_BIT_WR_ERR BIT(1) 65 #define SD_BIT_TIMEOUT BIT(2) 66 #define SD_BIT_CRC_ERR BIT(3) 67 68 #define SD_SLEEP_US 5 69 #define SD_TIMEOUT_US 20000 70 71 #define SDIRQ_CARD_DETECT 1 72 #define SDIRQ_SD_TO_MEM_DONE 2 73 #define SDIRQ_MEM_TO_SD_DONE 4 74 #define SDIRQ_CMD_DONE 8 75 76 struct litex_mmc_host { 77 struct mmc_host *mmc; 78 79 void __iomem *sdphy; 80 void __iomem *sdcore; 81 void __iomem *sdreader; 82 void __iomem *sdwriter; 83 void __iomem *sdirq; 84 85 void *buffer; 86 size_t buf_size; 87 dma_addr_t dma; 88 89 struct completion cmd_done; 90 int irq; 91 92 unsigned int ref_clk; 93 unsigned int sd_clk; 94 95 u32 resp[4]; 96 u16 rca; 97 98 bool is_bus_width_set; 99 bool app_cmd; 100 }; 101 102 static int litex_mmc_sdcard_wait_done(void __iomem *reg, struct device *dev) 103 { 104 u8 evt; 105 int ret; 106 107 ret = readx_poll_timeout(litex_read8, reg, evt, evt & SD_BIT_DONE, 108 SD_SLEEP_US, SD_TIMEOUT_US); 109 if (ret) 110 return ret; 111 if (evt == SD_BIT_DONE) 112 return 0; 113 if (evt & SD_BIT_WR_ERR) 114 return -EIO; 115 if (evt & SD_BIT_TIMEOUT) 116 return -ETIMEDOUT; 117 if (evt & SD_BIT_CRC_ERR) 118 return -EILSEQ; 119 dev_err(dev, "%s: unknown error (evt=%x)\n", __func__, evt); 120 return -EINVAL; 121 } 122 123 static int litex_mmc_send_cmd(struct litex_mmc_host *host, 124 u8 cmd, u32 arg, u8 response_len, u8 transfer) 125 { 126 struct device *dev = mmc_dev(host->mmc); 127 void __iomem *reg; 128 int ret; 129 u8 evt; 130 131 litex_write32(host->sdcore + LITEX_CORE_CMDARG, arg); 132 litex_write32(host->sdcore + LITEX_CORE_CMDCMD, 133 cmd << 8 | transfer << 5 | response_len); 134 litex_write8(host->sdcore + LITEX_CORE_CMDSND, 1); 135 136 /* 137 * Wait for an interrupt if we have an interrupt and either there is 138 * data to be transferred, or if the card can report busy via DAT0. 139 */ 140 if (host->irq > 0 && 141 (transfer != SD_CTL_DATA_XFER_NONE || 142 response_len == SD_CTL_RESP_SHORT_BUSY)) { 143 reinit_completion(&host->cmd_done); 144 litex_write32(host->sdirq + LITEX_IRQ_ENABLE, 145 SDIRQ_CMD_DONE | SDIRQ_CARD_DETECT); 146 wait_for_completion(&host->cmd_done); 147 } 148 149 ret = litex_mmc_sdcard_wait_done(host->sdcore + LITEX_CORE_CMDEVT, dev); 150 if (ret) { 151 dev_err(dev, "Command (cmd %d) error, status %d\n", cmd, ret); 152 return ret; 153 } 154 155 if (response_len != SD_CTL_RESP_NONE) { 156 /* 157 * NOTE: this matches the semantics of litex_read32() 158 * regardless of underlying arch endianness! 159 */ 160 memcpy_fromio(host->resp, 161 host->sdcore + LITEX_CORE_CMDRSP, 0x10); 162 } 163 164 if (!host->app_cmd && cmd == SD_SEND_RELATIVE_ADDR) 165 host->rca = (host->resp[3] >> 16); 166 167 host->app_cmd = (cmd == MMC_APP_CMD); 168 169 if (transfer == SD_CTL_DATA_XFER_NONE) 170 return ret; /* OK from prior litex_mmc_sdcard_wait_done() */ 171 172 ret = litex_mmc_sdcard_wait_done(host->sdcore + LITEX_CORE_DATEVT, dev); 173 if (ret) { 174 dev_err(dev, "Data xfer (cmd %d) error, status %d\n", cmd, ret); 175 return ret; 176 } 177 178 /* Wait for completion of (read or write) DMA transfer */ 179 reg = (transfer == SD_CTL_DATA_XFER_READ) ? 180 host->sdreader + LITEX_BLK2MEM_DONE : 181 host->sdwriter + LITEX_MEM2BLK_DONE; 182 ret = readx_poll_timeout(litex_read8, reg, evt, evt & SD_BIT_DONE, 183 SD_SLEEP_US, SD_TIMEOUT_US); 184 if (ret) 185 dev_err(dev, "DMA timeout (cmd %d)\n", cmd); 186 187 return ret; 188 } 189 190 static int litex_mmc_send_app_cmd(struct litex_mmc_host *host) 191 { 192 return litex_mmc_send_cmd(host, MMC_APP_CMD, host->rca << 16, 193 SD_CTL_RESP_SHORT, SD_CTL_DATA_XFER_NONE); 194 } 195 196 static int litex_mmc_send_set_bus_w_cmd(struct litex_mmc_host *host, u32 width) 197 { 198 return litex_mmc_send_cmd(host, SD_APP_SET_BUS_WIDTH, width, 199 SD_CTL_RESP_SHORT, SD_CTL_DATA_XFER_NONE); 200 } 201 202 static int litex_mmc_set_bus_width(struct litex_mmc_host *host) 203 { 204 bool app_cmd_sent; 205 int ret; 206 207 if (host->is_bus_width_set) 208 return 0; 209 210 /* Ensure 'app_cmd' precedes 'app_set_bus_width_cmd' */ 211 app_cmd_sent = host->app_cmd; /* was preceding command app_cmd? */ 212 if (!app_cmd_sent) { 213 ret = litex_mmc_send_app_cmd(host); 214 if (ret) 215 return ret; 216 } 217 218 /* LiteSDCard only supports 4-bit bus width */ 219 ret = litex_mmc_send_set_bus_w_cmd(host, MMC_BUS_WIDTH_4); 220 if (ret) 221 return ret; 222 223 /* Re-send 'app_cmd' if necessary */ 224 if (app_cmd_sent) { 225 ret = litex_mmc_send_app_cmd(host); 226 if (ret) 227 return ret; 228 } 229 230 host->is_bus_width_set = true; 231 232 return 0; 233 } 234 235 static int litex_mmc_get_cd(struct mmc_host *mmc) 236 { 237 struct litex_mmc_host *host = mmc_priv(mmc); 238 int ret; 239 240 if (!mmc_card_is_removable(mmc)) 241 return 1; 242 243 ret = !litex_read8(host->sdphy + LITEX_PHY_CARDDETECT); 244 if (ret) 245 return ret; 246 247 /* Ensure bus width will be set (again) upon card (re)insertion */ 248 host->is_bus_width_set = false; 249 250 return 0; 251 } 252 253 static irqreturn_t litex_mmc_interrupt(int irq, void *arg) 254 { 255 struct mmc_host *mmc = arg; 256 struct litex_mmc_host *host = mmc_priv(mmc); 257 u32 pending = litex_read32(host->sdirq + LITEX_IRQ_PENDING); 258 irqreturn_t ret = IRQ_NONE; 259 260 /* Check for card change interrupt */ 261 if (pending & SDIRQ_CARD_DETECT) { 262 litex_write32(host->sdirq + LITEX_IRQ_PENDING, 263 SDIRQ_CARD_DETECT); 264 mmc_detect_change(mmc, msecs_to_jiffies(10)); 265 ret = IRQ_HANDLED; 266 } 267 268 /* Check for command completed */ 269 if (pending & SDIRQ_CMD_DONE) { 270 /* Disable it so it doesn't keep interrupting */ 271 litex_write32(host->sdirq + LITEX_IRQ_ENABLE, 272 SDIRQ_CARD_DETECT); 273 complete(&host->cmd_done); 274 ret = IRQ_HANDLED; 275 } 276 277 return ret; 278 } 279 280 static u32 litex_mmc_response_len(struct mmc_command *cmd) 281 { 282 if (cmd->flags & MMC_RSP_136) 283 return SD_CTL_RESP_LONG; 284 if (!(cmd->flags & MMC_RSP_PRESENT)) 285 return SD_CTL_RESP_NONE; 286 if (cmd->flags & MMC_RSP_BUSY) 287 return SD_CTL_RESP_SHORT_BUSY; 288 return SD_CTL_RESP_SHORT; 289 } 290 291 static void litex_mmc_do_dma(struct litex_mmc_host *host, struct mmc_data *data, 292 unsigned int *len, bool *direct, u8 *transfer) 293 { 294 struct device *dev = mmc_dev(host->mmc); 295 dma_addr_t dma; 296 int sg_count; 297 298 /* 299 * Try to DMA directly to/from the data buffer. 300 * We can do that if the buffer can be mapped for DMA 301 * in one contiguous chunk. 302 */ 303 dma = host->dma; 304 *len = data->blksz * data->blocks; 305 sg_count = dma_map_sg(dev, data->sg, data->sg_len, 306 mmc_get_dma_dir(data)); 307 if (sg_count == 1) { 308 dma = sg_dma_address(data->sg); 309 *len = sg_dma_len(data->sg); 310 *direct = true; 311 } else if (*len > host->buf_size) 312 *len = host->buf_size; 313 314 if (data->flags & MMC_DATA_READ) { 315 litex_write8(host->sdreader + LITEX_BLK2MEM_ENA, 0); 316 litex_write64(host->sdreader + LITEX_BLK2MEM_BASE, dma); 317 litex_write32(host->sdreader + LITEX_BLK2MEM_LEN, *len); 318 litex_write8(host->sdreader + LITEX_BLK2MEM_ENA, 1); 319 *transfer = SD_CTL_DATA_XFER_READ; 320 } else if (data->flags & MMC_DATA_WRITE) { 321 if (!*direct) 322 sg_copy_to_buffer(data->sg, data->sg_len, 323 host->buffer, *len); 324 litex_write8(host->sdwriter + LITEX_MEM2BLK_ENA, 0); 325 litex_write64(host->sdwriter + LITEX_MEM2BLK_BASE, dma); 326 litex_write32(host->sdwriter + LITEX_MEM2BLK_LEN, *len); 327 litex_write8(host->sdwriter + LITEX_MEM2BLK_ENA, 1); 328 *transfer = SD_CTL_DATA_XFER_WRITE; 329 } else { 330 dev_warn(dev, "Data present w/o read or write flag.\n"); 331 /* Continue: set cmd status, mark req done */ 332 } 333 334 litex_write16(host->sdcore + LITEX_CORE_BLKLEN, data->blksz); 335 litex_write32(host->sdcore + LITEX_CORE_BLKCNT, data->blocks); 336 } 337 338 static void litex_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq) 339 { 340 struct litex_mmc_host *host = mmc_priv(mmc); 341 struct device *dev = mmc_dev(mmc); 342 struct mmc_command *cmd = mrq->cmd; 343 struct mmc_command *sbc = mrq->sbc; 344 struct mmc_data *data = mrq->data; 345 struct mmc_command *stop = mrq->stop; 346 unsigned int retries = cmd->retries; 347 unsigned int len = 0; 348 bool direct = false; 349 u32 response_len = litex_mmc_response_len(cmd); 350 u8 transfer = SD_CTL_DATA_XFER_NONE; 351 352 /* First check that the card is still there */ 353 if (!litex_mmc_get_cd(mmc)) { 354 cmd->error = -ENOMEDIUM; 355 mmc_request_done(mmc, mrq); 356 return; 357 } 358 359 /* Send set-block-count command if needed */ 360 if (sbc) { 361 sbc->error = litex_mmc_send_cmd(host, sbc->opcode, sbc->arg, 362 litex_mmc_response_len(sbc), 363 SD_CTL_DATA_XFER_NONE); 364 if (sbc->error) { 365 host->is_bus_width_set = false; 366 mmc_request_done(mmc, mrq); 367 return; 368 } 369 } 370 371 if (data) { 372 /* 373 * LiteSDCard only supports 4-bit bus width; therefore, we MUST 374 * inject a SET_BUS_WIDTH (acmd6) before the very first data 375 * transfer, earlier than when the mmc subsystem would normally 376 * get around to it! 377 */ 378 cmd->error = litex_mmc_set_bus_width(host); 379 if (cmd->error) { 380 dev_err(dev, "Can't set bus width!\n"); 381 mmc_request_done(mmc, mrq); 382 return; 383 } 384 385 litex_mmc_do_dma(host, data, &len, &direct, &transfer); 386 } 387 388 do { 389 cmd->error = litex_mmc_send_cmd(host, cmd->opcode, cmd->arg, 390 response_len, transfer); 391 } while (cmd->error && retries-- > 0); 392 393 if (cmd->error) { 394 /* Card may be gone; don't assume bus width is still set */ 395 host->is_bus_width_set = false; 396 } 397 398 if (response_len == SD_CTL_RESP_SHORT) { 399 /* Pull short response fields from appropriate host registers */ 400 cmd->resp[0] = host->resp[3]; 401 cmd->resp[1] = host->resp[2] & 0xFF; 402 } else if (response_len == SD_CTL_RESP_LONG) { 403 cmd->resp[0] = host->resp[0]; 404 cmd->resp[1] = host->resp[1]; 405 cmd->resp[2] = host->resp[2]; 406 cmd->resp[3] = host->resp[3]; 407 } 408 409 /* Send stop-transmission command if required */ 410 if (stop && (cmd->error || !sbc)) { 411 stop->error = litex_mmc_send_cmd(host, stop->opcode, stop->arg, 412 litex_mmc_response_len(stop), 413 SD_CTL_DATA_XFER_NONE); 414 if (stop->error) 415 host->is_bus_width_set = false; 416 } 417 418 if (data) { 419 dma_unmap_sg(dev, data->sg, data->sg_len, 420 mmc_get_dma_dir(data)); 421 } 422 423 if (!cmd->error && transfer != SD_CTL_DATA_XFER_NONE) { 424 data->bytes_xfered = min(len, mmc->max_req_size); 425 if (transfer == SD_CTL_DATA_XFER_READ && !direct) { 426 sg_copy_from_buffer(data->sg, sg_nents(data->sg), 427 host->buffer, data->bytes_xfered); 428 } 429 } 430 431 mmc_request_done(mmc, mrq); 432 } 433 434 static void litex_mmc_setclk(struct litex_mmc_host *host, unsigned int freq) 435 { 436 struct device *dev = mmc_dev(host->mmc); 437 u32 div; 438 439 div = freq ? host->ref_clk / freq : 256U; 440 div = roundup_pow_of_two(div); 441 div = clamp(div, 2U, 256U); 442 dev_dbg(dev, "sd_clk_freq=%d: set to %d via div=%d\n", 443 freq, host->ref_clk / div, div); 444 litex_write16(host->sdphy + LITEX_PHY_CLOCKERDIV, div); 445 host->sd_clk = freq; 446 } 447 448 static void litex_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) 449 { 450 struct litex_mmc_host *host = mmc_priv(mmc); 451 452 /* 453 * NOTE: Ignore any ios->bus_width updates; they occur right after 454 * the mmc core sends its own acmd6 bus-width change notification, 455 * which is redundant since we snoop on the command flow and inject 456 * an early acmd6 before the first data transfer command is sent! 457 */ 458 459 /* Update sd_clk */ 460 if (ios->clock != host->sd_clk) 461 litex_mmc_setclk(host, ios->clock); 462 } 463 464 static const struct mmc_host_ops litex_mmc_ops = { 465 .get_cd = litex_mmc_get_cd, 466 .request = litex_mmc_request, 467 .set_ios = litex_mmc_set_ios, 468 }; 469 470 static int litex_mmc_irq_init(struct platform_device *pdev, 471 struct litex_mmc_host *host) 472 { 473 struct device *dev = mmc_dev(host->mmc); 474 int ret; 475 476 ret = platform_get_irq_optional(pdev, 0); 477 if (ret < 0 && ret != -ENXIO) 478 return ret; 479 if (ret > 0) 480 host->irq = ret; 481 else { 482 dev_warn(dev, "Failed to get IRQ, using polling\n"); 483 goto use_polling; 484 } 485 486 host->sdirq = devm_platform_ioremap_resource_byname(pdev, "irq"); 487 if (IS_ERR(host->sdirq)) 488 return PTR_ERR(host->sdirq); 489 490 ret = devm_request_irq(dev, host->irq, litex_mmc_interrupt, 0, 491 "litex-mmc", host->mmc); 492 if (ret < 0) { 493 dev_warn(dev, "IRQ request error %d, using polling\n", ret); 494 goto use_polling; 495 } 496 497 /* Clear & enable card-change interrupts */ 498 litex_write32(host->sdirq + LITEX_IRQ_PENDING, SDIRQ_CARD_DETECT); 499 litex_write32(host->sdirq + LITEX_IRQ_ENABLE, SDIRQ_CARD_DETECT); 500 501 return 0; 502 503 use_polling: 504 host->mmc->caps |= MMC_CAP_NEEDS_POLL; 505 host->irq = 0; 506 return 0; 507 } 508 509 static void litex_mmc_free_host_wrapper(void *mmc) 510 { 511 mmc_free_host(mmc); 512 } 513 514 static int litex_mmc_probe(struct platform_device *pdev) 515 { 516 struct device *dev = &pdev->dev; 517 struct litex_mmc_host *host; 518 struct mmc_host *mmc; 519 struct clk *clk; 520 int ret; 521 522 /* 523 * NOTE: defaults to max_[req,seg]_size=PAGE_SIZE, max_blk_size=512, 524 * and max_blk_count accordingly set to 8; 525 * If for some reason we need to modify max_blk_count, we must also 526 * re-calculate `max_[req,seg]_size = max_blk_size * max_blk_count;` 527 */ 528 mmc = mmc_alloc_host(sizeof(struct litex_mmc_host), dev); 529 if (!mmc) 530 return -ENOMEM; 531 532 ret = devm_add_action_or_reset(dev, litex_mmc_free_host_wrapper, mmc); 533 if (ret) 534 return dev_err_probe(dev, ret, 535 "Can't register mmc_free_host action\n"); 536 537 host = mmc_priv(mmc); 538 host->mmc = mmc; 539 540 /* Initialize clock source */ 541 clk = devm_clk_get(dev, NULL); 542 if (IS_ERR(clk)) 543 return dev_err_probe(dev, PTR_ERR(clk), "can't get clock\n"); 544 host->ref_clk = clk_get_rate(clk); 545 host->sd_clk = 0; 546 547 /* 548 * LiteSDCard only supports 4-bit bus width; therefore, we MUST inject 549 * a SET_BUS_WIDTH (acmd6) before the very first data transfer, earlier 550 * than when the mmc subsystem would normally get around to it! 551 */ 552 host->is_bus_width_set = false; 553 host->app_cmd = false; 554 555 /* LiteSDCard can support 64-bit DMA addressing */ 556 ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(64)); 557 if (ret) 558 return ret; 559 560 host->buf_size = mmc->max_req_size * 2; 561 host->buffer = dmam_alloc_coherent(dev, host->buf_size, 562 &host->dma, GFP_KERNEL); 563 if (host->buffer == NULL) 564 return -ENOMEM; 565 566 host->sdphy = devm_platform_ioremap_resource_byname(pdev, "phy"); 567 if (IS_ERR(host->sdphy)) 568 return PTR_ERR(host->sdphy); 569 570 host->sdcore = devm_platform_ioremap_resource_byname(pdev, "core"); 571 if (IS_ERR(host->sdcore)) 572 return PTR_ERR(host->sdcore); 573 574 host->sdreader = devm_platform_ioremap_resource_byname(pdev, "reader"); 575 if (IS_ERR(host->sdreader)) 576 return PTR_ERR(host->sdreader); 577 578 host->sdwriter = devm_platform_ioremap_resource_byname(pdev, "writer"); 579 if (IS_ERR(host->sdwriter)) 580 return PTR_ERR(host->sdwriter); 581 582 /* Ensure DMA bus masters are disabled */ 583 litex_write8(host->sdreader + LITEX_BLK2MEM_ENA, 0); 584 litex_write8(host->sdwriter + LITEX_MEM2BLK_ENA, 0); 585 586 init_completion(&host->cmd_done); 587 ret = litex_mmc_irq_init(pdev, host); 588 if (ret) 589 return ret; 590 591 mmc->ops = &litex_mmc_ops; 592 593 ret = mmc_regulator_get_supply(mmc); 594 if (ret || mmc->ocr_avail == 0) { 595 dev_warn(dev, "can't get voltage, defaulting to 3.3V\n"); 596 mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; 597 } 598 599 /* 600 * Set default sd_clk frequency range based on empirical observations 601 * of LiteSDCard gateware behavior on typical SDCard media 602 */ 603 mmc->f_min = 12.5e6; 604 mmc->f_max = 50e6; 605 606 ret = mmc_of_parse(mmc); 607 if (ret) 608 return ret; 609 610 /* Force 4-bit bus_width (only width supported by hardware) */ 611 mmc->caps &= ~MMC_CAP_8_BIT_DATA; 612 mmc->caps |= MMC_CAP_4_BIT_DATA; 613 614 /* Set default capabilities */ 615 mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY | 616 MMC_CAP_DRIVER_TYPE_D | 617 MMC_CAP_CMD23; 618 mmc->caps2 |= MMC_CAP2_NO_WRITE_PROTECT | 619 MMC_CAP2_NO_SDIO | 620 MMC_CAP2_NO_MMC; 621 622 platform_set_drvdata(pdev, host); 623 624 ret = mmc_add_host(mmc); 625 if (ret) 626 return ret; 627 628 dev_info(dev, "LiteX MMC controller initialized.\n"); 629 return 0; 630 } 631 632 static int litex_mmc_remove(struct platform_device *pdev) 633 { 634 struct litex_mmc_host *host = platform_get_drvdata(pdev); 635 636 mmc_remove_host(host->mmc); 637 return 0; 638 } 639 640 static const struct of_device_id litex_match[] = { 641 { .compatible = "litex,mmc" }, 642 { } 643 }; 644 MODULE_DEVICE_TABLE(of, litex_match); 645 646 static struct platform_driver litex_mmc_driver = { 647 .probe = litex_mmc_probe, 648 .remove = litex_mmc_remove, 649 .driver = { 650 .name = "litex-mmc", 651 .of_match_table = litex_match, 652 .probe_type = PROBE_PREFER_ASYNCHRONOUS, 653 }, 654 }; 655 module_platform_driver(litex_mmc_driver); 656 657 MODULE_DESCRIPTION("LiteX SDCard driver"); 658 MODULE_AUTHOR("Antmicro <contact@antmicro.com>"); 659 MODULE_AUTHOR("Kamil Rakoczy <krakoczy@antmicro.com>"); 660 MODULE_AUTHOR("Maciej Dudek <mdudek@internships.antmicro.com>"); 661 MODULE_AUTHOR("Paul Mackerras <paulus@ozlabs.org>"); 662 MODULE_AUTHOR("Gabriel Somlo <gsomlo@gmail.com>"); 663 MODULE_LICENSE("GPL v2"); 664