1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd 4 */ 5 6 #include <linux/module.h> 7 #include <linux/platform_device.h> 8 #include <linux/clk.h> 9 #include <linux/mmc/host.h> 10 #include <linux/of_address.h> 11 #include <linux/mmc/slot-gpio.h> 12 #include <linux/pm_runtime.h> 13 #include <linux/slab.h> 14 15 #include "dw_mmc.h" 16 #include "dw_mmc-pltfm.h" 17 18 #define RK3288_CLKGEN_DIV 2 19 20 struct dw_mci_rockchip_priv_data { 21 struct clk *drv_clk; 22 struct clk *sample_clk; 23 int default_sample_phase; 24 int num_phases; 25 }; 26 27 static void dw_mci_rk3288_set_ios(struct dw_mci *host, struct mmc_ios *ios) 28 { 29 struct dw_mci_rockchip_priv_data *priv = host->priv; 30 int ret; 31 unsigned int cclkin; 32 u32 bus_hz; 33 34 if (ios->clock == 0) 35 return; 36 37 /* 38 * cclkin: source clock of mmc controller 39 * bus_hz: card interface clock generated by CLKGEN 40 * bus_hz = cclkin / RK3288_CLKGEN_DIV 41 * ios->clock = (div == 0) ? bus_hz : (bus_hz / (2 * div)) 42 * 43 * Note: div can only be 0 or 1, but div must be set to 1 for eMMC 44 * DDR52 8-bit mode. 45 */ 46 if (ios->bus_width == MMC_BUS_WIDTH_8 && 47 ios->timing == MMC_TIMING_MMC_DDR52) 48 cclkin = 2 * ios->clock * RK3288_CLKGEN_DIV; 49 else 50 cclkin = ios->clock * RK3288_CLKGEN_DIV; 51 52 ret = clk_set_rate(host->ciu_clk, cclkin); 53 if (ret) 54 dev_warn(host->dev, "failed to set rate %uHz\n", ios->clock); 55 56 bus_hz = clk_get_rate(host->ciu_clk) / RK3288_CLKGEN_DIV; 57 if (bus_hz != host->bus_hz) { 58 host->bus_hz = bus_hz; 59 /* force dw_mci_setup_bus() */ 60 host->current_speed = 0; 61 } 62 63 /* Make sure we use phases which we can enumerate with */ 64 if (!IS_ERR(priv->sample_clk) && ios->timing <= MMC_TIMING_SD_HS) 65 clk_set_phase(priv->sample_clk, priv->default_sample_phase); 66 67 /* 68 * Set the drive phase offset based on speed mode to achieve hold times. 69 * 70 * NOTE: this is _not_ a value that is dynamically tuned and is also 71 * _not_ a value that will vary from board to board. It is a value 72 * that could vary between different SoC models if they had massively 73 * different output clock delays inside their dw_mmc IP block (delay_o), 74 * but since it's OK to overshoot a little we don't need to do complex 75 * calculations and can pick values that will just work for everyone. 76 * 77 * When picking values we'll stick with picking 0/90/180/270 since 78 * those can be made very accurately on all known Rockchip SoCs. 79 * 80 * Note that these values match values from the DesignWare Databook 81 * tables for the most part except for SDR12 and "ID mode". For those 82 * two modes the databook calculations assume a clock in of 50MHz. As 83 * seen above, we always use a clock in rate that is exactly the 84 * card's input clock (times RK3288_CLKGEN_DIV, but that gets divided 85 * back out before the controller sees it). 86 * 87 * From measurement of a single device, it appears that delay_o is 88 * about .5 ns. Since we try to leave a bit of margin, it's expected 89 * that numbers here will be fine even with much larger delay_o 90 * (the 1.4 ns assumed by the DesignWare Databook would result in the 91 * same results, for instance). 92 */ 93 if (!IS_ERR(priv->drv_clk)) { 94 int phase; 95 96 /* 97 * In almost all cases a 90 degree phase offset will provide 98 * sufficient hold times across all valid input clock rates 99 * assuming delay_o is not absurd for a given SoC. We'll use 100 * that as a default. 101 */ 102 phase = 90; 103 104 switch (ios->timing) { 105 case MMC_TIMING_MMC_DDR52: 106 /* 107 * Since clock in rate with MMC_DDR52 is doubled when 108 * bus width is 8 we need to double the phase offset 109 * to get the same timings. 110 */ 111 if (ios->bus_width == MMC_BUS_WIDTH_8) 112 phase = 180; 113 break; 114 case MMC_TIMING_UHS_SDR104: 115 case MMC_TIMING_MMC_HS200: 116 /* 117 * In the case of 150 MHz clock (typical max for 118 * Rockchip SoCs), 90 degree offset will add a delay 119 * of 1.67 ns. That will meet min hold time of .8 ns 120 * as long as clock output delay is < .87 ns. On 121 * SoCs measured this seems to be OK, but it doesn't 122 * hurt to give margin here, so we use 180. 123 */ 124 phase = 180; 125 break; 126 } 127 128 clk_set_phase(priv->drv_clk, phase); 129 } 130 } 131 132 #define TUNING_ITERATION_TO_PHASE(i, num_phases) \ 133 (DIV_ROUND_UP((i) * 360, num_phases)) 134 135 static int dw_mci_rk3288_execute_tuning(struct dw_mci_slot *slot, u32 opcode) 136 { 137 struct dw_mci *host = slot->host; 138 struct dw_mci_rockchip_priv_data *priv = host->priv; 139 struct mmc_host *mmc = slot->mmc; 140 int ret = 0; 141 int i; 142 bool v, prev_v = 0, first_v; 143 struct range_t { 144 int start; 145 int end; /* inclusive */ 146 }; 147 struct range_t *ranges; 148 unsigned int range_count = 0; 149 int longest_range_len = -1; 150 int longest_range = -1; 151 int middle_phase; 152 153 if (IS_ERR(priv->sample_clk)) { 154 dev_err(host->dev, "Tuning clock (sample_clk) not defined.\n"); 155 return -EIO; 156 } 157 158 ranges = kmalloc_array(priv->num_phases / 2 + 1, 159 sizeof(*ranges), GFP_KERNEL); 160 if (!ranges) 161 return -ENOMEM; 162 163 /* Try each phase and extract good ranges */ 164 for (i = 0; i < priv->num_phases; ) { 165 clk_set_phase(priv->sample_clk, 166 TUNING_ITERATION_TO_PHASE(i, priv->num_phases)); 167 168 v = !mmc_send_tuning(mmc, opcode, NULL); 169 170 if (i == 0) 171 first_v = v; 172 173 if ((!prev_v) && v) { 174 range_count++; 175 ranges[range_count-1].start = i; 176 } 177 if (v) { 178 ranges[range_count-1].end = i; 179 i++; 180 } else if (i == priv->num_phases - 1) { 181 /* No extra skipping rules if we're at the end */ 182 i++; 183 } else { 184 /* 185 * No need to check too close to an invalid 186 * one since testing bad phases is slow. Skip 187 * 20 degrees. 188 */ 189 i += DIV_ROUND_UP(20 * priv->num_phases, 360); 190 191 /* Always test the last one */ 192 if (i >= priv->num_phases) 193 i = priv->num_phases - 1; 194 } 195 196 prev_v = v; 197 } 198 199 if (range_count == 0) { 200 dev_warn(host->dev, "All phases bad!"); 201 ret = -EIO; 202 goto free; 203 } 204 205 /* wrap around case, merge the end points */ 206 if ((range_count > 1) && first_v && v) { 207 ranges[0].start = ranges[range_count-1].start; 208 range_count--; 209 } 210 211 if (ranges[0].start == 0 && ranges[0].end == priv->num_phases - 1) { 212 clk_set_phase(priv->sample_clk, priv->default_sample_phase); 213 dev_info(host->dev, "All phases work, using default phase %d.", 214 priv->default_sample_phase); 215 goto free; 216 } 217 218 /* Find the longest range */ 219 for (i = 0; i < range_count; i++) { 220 int len = (ranges[i].end - ranges[i].start + 1); 221 222 if (len < 0) 223 len += priv->num_phases; 224 225 if (longest_range_len < len) { 226 longest_range_len = len; 227 longest_range = i; 228 } 229 230 dev_dbg(host->dev, "Good phase range %d-%d (%d len)\n", 231 TUNING_ITERATION_TO_PHASE(ranges[i].start, 232 priv->num_phases), 233 TUNING_ITERATION_TO_PHASE(ranges[i].end, 234 priv->num_phases), 235 len 236 ); 237 } 238 239 dev_dbg(host->dev, "Best phase range %d-%d (%d len)\n", 240 TUNING_ITERATION_TO_PHASE(ranges[longest_range].start, 241 priv->num_phases), 242 TUNING_ITERATION_TO_PHASE(ranges[longest_range].end, 243 priv->num_phases), 244 longest_range_len 245 ); 246 247 middle_phase = ranges[longest_range].start + longest_range_len / 2; 248 middle_phase %= priv->num_phases; 249 dev_info(host->dev, "Successfully tuned phase to %d\n", 250 TUNING_ITERATION_TO_PHASE(middle_phase, priv->num_phases)); 251 252 clk_set_phase(priv->sample_clk, 253 TUNING_ITERATION_TO_PHASE(middle_phase, 254 priv->num_phases)); 255 256 free: 257 kfree(ranges); 258 return ret; 259 } 260 261 static int dw_mci_rk3288_parse_dt(struct dw_mci *host) 262 { 263 struct device_node *np = host->dev->of_node; 264 struct dw_mci_rockchip_priv_data *priv; 265 266 priv = devm_kzalloc(host->dev, sizeof(*priv), GFP_KERNEL); 267 if (!priv) 268 return -ENOMEM; 269 270 if (of_property_read_u32(np, "rockchip,desired-num-phases", 271 &priv->num_phases)) 272 priv->num_phases = 360; 273 274 if (of_property_read_u32(np, "rockchip,default-sample-phase", 275 &priv->default_sample_phase)) 276 priv->default_sample_phase = 0; 277 278 priv->drv_clk = devm_clk_get(host->dev, "ciu-drive"); 279 if (IS_ERR(priv->drv_clk)) 280 dev_dbg(host->dev, "ciu-drive not available\n"); 281 282 priv->sample_clk = devm_clk_get(host->dev, "ciu-sample"); 283 if (IS_ERR(priv->sample_clk)) 284 dev_dbg(host->dev, "ciu-sample not available\n"); 285 286 host->priv = priv; 287 288 return 0; 289 } 290 291 static int dw_mci_rockchip_init(struct dw_mci *host) 292 { 293 /* It is slot 8 on Rockchip SoCs */ 294 host->sdio_id0 = 8; 295 296 if (of_device_is_compatible(host->dev->of_node, 297 "rockchip,rk3288-dw-mshc")) 298 host->bus_hz /= RK3288_CLKGEN_DIV; 299 300 return 0; 301 } 302 303 /* Common capabilities of RK3288 SoC */ 304 static unsigned long dw_mci_rk3288_dwmmc_caps[4] = { 305 MMC_CAP_CMD23, 306 MMC_CAP_CMD23, 307 MMC_CAP_CMD23, 308 MMC_CAP_CMD23, 309 }; 310 311 static const struct dw_mci_drv_data rk2928_drv_data = { 312 .init = dw_mci_rockchip_init, 313 }; 314 315 static const struct dw_mci_drv_data rk3288_drv_data = { 316 .caps = dw_mci_rk3288_dwmmc_caps, 317 .num_caps = ARRAY_SIZE(dw_mci_rk3288_dwmmc_caps), 318 .set_ios = dw_mci_rk3288_set_ios, 319 .execute_tuning = dw_mci_rk3288_execute_tuning, 320 .parse_dt = dw_mci_rk3288_parse_dt, 321 .init = dw_mci_rockchip_init, 322 }; 323 324 static const struct of_device_id dw_mci_rockchip_match[] = { 325 { .compatible = "rockchip,rk2928-dw-mshc", 326 .data = &rk2928_drv_data }, 327 { .compatible = "rockchip,rk3288-dw-mshc", 328 .data = &rk3288_drv_data }, 329 {}, 330 }; 331 MODULE_DEVICE_TABLE(of, dw_mci_rockchip_match); 332 333 static int dw_mci_rockchip_probe(struct platform_device *pdev) 334 { 335 const struct dw_mci_drv_data *drv_data; 336 const struct of_device_id *match; 337 int ret; 338 339 if (!pdev->dev.of_node) 340 return -ENODEV; 341 342 match = of_match_node(dw_mci_rockchip_match, pdev->dev.of_node); 343 drv_data = match->data; 344 345 pm_runtime_get_noresume(&pdev->dev); 346 pm_runtime_set_active(&pdev->dev); 347 pm_runtime_enable(&pdev->dev); 348 pm_runtime_set_autosuspend_delay(&pdev->dev, 50); 349 pm_runtime_use_autosuspend(&pdev->dev); 350 351 ret = dw_mci_pltfm_register(pdev, drv_data); 352 if (ret) { 353 pm_runtime_disable(&pdev->dev); 354 pm_runtime_set_suspended(&pdev->dev); 355 pm_runtime_put_noidle(&pdev->dev); 356 return ret; 357 } 358 359 pm_runtime_put_autosuspend(&pdev->dev); 360 361 return 0; 362 } 363 364 static int dw_mci_rockchip_remove(struct platform_device *pdev) 365 { 366 pm_runtime_get_sync(&pdev->dev); 367 pm_runtime_disable(&pdev->dev); 368 pm_runtime_put_noidle(&pdev->dev); 369 370 return dw_mci_pltfm_remove(pdev); 371 } 372 373 static const struct dev_pm_ops dw_mci_rockchip_dev_pm_ops = { 374 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, 375 pm_runtime_force_resume) 376 SET_RUNTIME_PM_OPS(dw_mci_runtime_suspend, 377 dw_mci_runtime_resume, 378 NULL) 379 }; 380 381 static struct platform_driver dw_mci_rockchip_pltfm_driver = { 382 .probe = dw_mci_rockchip_probe, 383 .remove = dw_mci_rockchip_remove, 384 .driver = { 385 .name = "dwmmc_rockchip", 386 .probe_type = PROBE_PREFER_ASYNCHRONOUS, 387 .of_match_table = dw_mci_rockchip_match, 388 .pm = &dw_mci_rockchip_dev_pm_ops, 389 }, 390 }; 391 392 module_platform_driver(dw_mci_rockchip_pltfm_driver); 393 394 MODULE_AUTHOR("Addy Ke <addy.ke@rock-chips.com>"); 395 MODULE_DESCRIPTION("Rockchip Specific DW-MSHC Driver Extension"); 396 MODULE_ALIAS("platform:dwmmc_rockchip"); 397 MODULE_LICENSE("GPL v2"); 398