1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * cb710/mmc.c 4 * 5 * Copyright by Michał Mirosław, 2008-2009 6 */ 7 #include <linux/kernel.h> 8 #include <linux/module.h> 9 #include <linux/pci.h> 10 #include <linux/delay.h> 11 #include "cb710-mmc.h" 12 13 #define CB710_MMC_REQ_TIMEOUT_MS 2000 14 15 static const u8 cb710_clock_divider_log2[8] = { 16 /* 1, 2, 4, 8, 16, 32, 128, 512 */ 17 0, 1, 2, 3, 4, 5, 7, 9 18 }; 19 #define CB710_MAX_DIVIDER_IDX \ 20 (ARRAY_SIZE(cb710_clock_divider_log2) - 1) 21 22 static const u8 cb710_src_freq_mhz[16] = { 23 33, 10, 20, 25, 30, 35, 40, 45, 24 50, 55, 60, 65, 70, 75, 80, 85 25 }; 26 27 static void cb710_mmc_select_clock_divider(struct mmc_host *mmc, int hz) 28 { 29 struct cb710_slot *slot = cb710_mmc_to_slot(mmc); 30 struct pci_dev *pdev = cb710_slot_to_chip(slot)->pdev; 31 u32 src_freq_idx; 32 u32 divider_idx; 33 int src_hz; 34 35 /* on CB710 in HP nx9500: 36 * src_freq_idx == 0 37 * indexes 1-7 work as written in the table 38 * indexes 0,8-15 give no clock output 39 */ 40 pci_read_config_dword(pdev, 0x48, &src_freq_idx); 41 src_freq_idx = (src_freq_idx >> 16) & 0xF; 42 src_hz = cb710_src_freq_mhz[src_freq_idx] * 1000000; 43 44 for (divider_idx = 0; divider_idx < CB710_MAX_DIVIDER_IDX; ++divider_idx) { 45 if (hz >= src_hz >> cb710_clock_divider_log2[divider_idx]) 46 break; 47 } 48 49 if (src_freq_idx) 50 divider_idx |= 0x8; 51 else if (divider_idx == 0) 52 divider_idx = 1; 53 54 cb710_pci_update_config_reg(pdev, 0x40, ~0xF0000000, divider_idx << 28); 55 56 dev_dbg(cb710_slot_dev(slot), 57 "clock set to %d Hz, wanted %d Hz; src_freq_idx = %d, divider_idx = %d|%d\n", 58 src_hz >> cb710_clock_divider_log2[divider_idx & 7], 59 hz, src_freq_idx, divider_idx & 7, divider_idx & 8); 60 } 61 62 static void __cb710_mmc_enable_irq(struct cb710_slot *slot, 63 unsigned short enable, unsigned short mask) 64 { 65 /* clear global IE 66 * - it gets set later if any interrupt sources are enabled */ 67 mask |= CB710_MMC_IE_IRQ_ENABLE; 68 69 /* look like interrupt is fired whenever 70 * WORD[0x0C] & WORD[0x10] != 0; 71 * -> bit 15 port 0x0C seems to be global interrupt enable 72 */ 73 74 enable = (cb710_read_port_16(slot, CB710_MMC_IRQ_ENABLE_PORT) 75 & ~mask) | enable; 76 77 if (enable) 78 enable |= CB710_MMC_IE_IRQ_ENABLE; 79 80 cb710_write_port_16(slot, CB710_MMC_IRQ_ENABLE_PORT, enable); 81 } 82 83 static void cb710_mmc_enable_irq(struct cb710_slot *slot, 84 unsigned short enable, unsigned short mask) 85 { 86 struct cb710_mmc_reader *reader = mmc_priv(cb710_slot_to_mmc(slot)); 87 unsigned long flags; 88 89 spin_lock_irqsave(&reader->irq_lock, flags); 90 /* this is the only thing irq_lock protects */ 91 __cb710_mmc_enable_irq(slot, enable, mask); 92 spin_unlock_irqrestore(&reader->irq_lock, flags); 93 } 94 95 static void cb710_mmc_reset_events(struct cb710_slot *slot) 96 { 97 cb710_write_port_8(slot, CB710_MMC_STATUS0_PORT, 0xFF); 98 cb710_write_port_8(slot, CB710_MMC_STATUS1_PORT, 0xFF); 99 cb710_write_port_8(slot, CB710_MMC_STATUS2_PORT, 0xFF); 100 } 101 102 static void cb710_mmc_enable_4bit_data(struct cb710_slot *slot, int enable) 103 { 104 if (enable) 105 cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT, 106 CB710_MMC_C1_4BIT_DATA_BUS, 0); 107 else 108 cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT, 109 0, CB710_MMC_C1_4BIT_DATA_BUS); 110 } 111 112 static int cb710_check_event(struct cb710_slot *slot, u8 what) 113 { 114 u16 status; 115 116 status = cb710_read_port_16(slot, CB710_MMC_STATUS_PORT); 117 118 if (status & CB710_MMC_S0_FIFO_UNDERFLOW) { 119 /* it is just a guess, so log it */ 120 dev_dbg(cb710_slot_dev(slot), 121 "CHECK : ignoring bit 6 in status %04X\n", status); 122 cb710_write_port_8(slot, CB710_MMC_STATUS0_PORT, 123 CB710_MMC_S0_FIFO_UNDERFLOW); 124 status &= ~CB710_MMC_S0_FIFO_UNDERFLOW; 125 } 126 127 if (status & CB710_MMC_STATUS_ERROR_EVENTS) { 128 dev_dbg(cb710_slot_dev(slot), 129 "CHECK : returning EIO on status %04X\n", status); 130 cb710_write_port_8(slot, CB710_MMC_STATUS0_PORT, status & 0xFF); 131 cb710_write_port_8(slot, CB710_MMC_STATUS1_PORT, 132 CB710_MMC_S1_RESET); 133 return -EIO; 134 } 135 136 /* 'what' is a bit in MMC_STATUS1 */ 137 if ((status >> 8) & what) { 138 cb710_write_port_8(slot, CB710_MMC_STATUS1_PORT, what); 139 return 1; 140 } 141 142 return 0; 143 } 144 145 static int cb710_wait_for_event(struct cb710_slot *slot, u8 what) 146 { 147 int err = 0; 148 unsigned limit = 2000000; /* FIXME: real timeout */ 149 150 #ifdef CONFIG_CB710_DEBUG 151 u32 e, x; 152 e = cb710_read_port_32(slot, CB710_MMC_STATUS_PORT); 153 #endif 154 155 while (!(err = cb710_check_event(slot, what))) { 156 if (!--limit) { 157 cb710_dump_regs(cb710_slot_to_chip(slot), 158 CB710_DUMP_REGS_MMC); 159 err = -ETIMEDOUT; 160 break; 161 } 162 udelay(1); 163 } 164 165 #ifdef CONFIG_CB710_DEBUG 166 x = cb710_read_port_32(slot, CB710_MMC_STATUS_PORT); 167 168 limit = 2000000 - limit; 169 if (limit > 100) 170 dev_dbg(cb710_slot_dev(slot), 171 "WAIT10: waited %d loops, what %d, entry val %08X, exit val %08X\n", 172 limit, what, e, x); 173 #endif 174 return err < 0 ? err : 0; 175 } 176 177 178 static int cb710_wait_while_busy(struct cb710_slot *slot, uint8_t mask) 179 { 180 unsigned limit = 500000; /* FIXME: real timeout */ 181 int err = 0; 182 183 #ifdef CONFIG_CB710_DEBUG 184 u32 e, x; 185 e = cb710_read_port_32(slot, CB710_MMC_STATUS_PORT); 186 #endif 187 188 while (cb710_read_port_8(slot, CB710_MMC_STATUS2_PORT) & mask) { 189 if (!--limit) { 190 cb710_dump_regs(cb710_slot_to_chip(slot), 191 CB710_DUMP_REGS_MMC); 192 err = -ETIMEDOUT; 193 break; 194 } 195 udelay(1); 196 } 197 198 #ifdef CONFIG_CB710_DEBUG 199 x = cb710_read_port_32(slot, CB710_MMC_STATUS_PORT); 200 201 limit = 500000 - limit; 202 if (limit > 100) 203 dev_dbg(cb710_slot_dev(slot), 204 "WAIT12: waited %d loops, mask %02X, entry val %08X, exit val %08X\n", 205 limit, mask, e, x); 206 #endif 207 return err; 208 } 209 210 static void cb710_mmc_set_transfer_size(struct cb710_slot *slot, 211 size_t count, size_t blocksize) 212 { 213 cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20); 214 cb710_write_port_32(slot, CB710_MMC_TRANSFER_SIZE_PORT, 215 ((count - 1) << 16)|(blocksize - 1)); 216 217 dev_vdbg(cb710_slot_dev(slot), "set up for %zu block%s of %zu bytes\n", 218 count, count == 1 ? "" : "s", blocksize); 219 } 220 221 static void cb710_mmc_fifo_hack(struct cb710_slot *slot) 222 { 223 /* without this, received data is prepended with 8-bytes of zeroes */ 224 u32 r1, r2; 225 int ok = 0; 226 227 r1 = cb710_read_port_32(slot, CB710_MMC_DATA_PORT); 228 r2 = cb710_read_port_32(slot, CB710_MMC_DATA_PORT); 229 if (cb710_read_port_8(slot, CB710_MMC_STATUS0_PORT) 230 & CB710_MMC_S0_FIFO_UNDERFLOW) { 231 cb710_write_port_8(slot, CB710_MMC_STATUS0_PORT, 232 CB710_MMC_S0_FIFO_UNDERFLOW); 233 ok = 1; 234 } 235 236 dev_dbg(cb710_slot_dev(slot), 237 "FIFO-read-hack: expected STATUS0 bit was %s\n", 238 ok ? "set." : "NOT SET!"); 239 dev_dbg(cb710_slot_dev(slot), 240 "FIFO-read-hack: dwords ignored: %08X %08X - %s\n", 241 r1, r2, (r1|r2) ? "BAD (NOT ZERO)!" : "ok"); 242 } 243 244 static int cb710_mmc_receive_pio(struct cb710_slot *slot, 245 struct sg_mapping_iter *miter, size_t dw_count) 246 { 247 if (!(cb710_read_port_8(slot, CB710_MMC_STATUS2_PORT) & CB710_MMC_S2_FIFO_READY)) { 248 int err = cb710_wait_for_event(slot, 249 CB710_MMC_S1_PIO_TRANSFER_DONE); 250 if (err) 251 return err; 252 } 253 254 cb710_sg_dwiter_write_from_io(miter, 255 slot->iobase + CB710_MMC_DATA_PORT, dw_count); 256 257 return 0; 258 } 259 260 static bool cb710_is_transfer_size_supported(struct mmc_data *data) 261 { 262 return !(data->blksz & 15 && (data->blocks != 1 || data->blksz != 8)); 263 } 264 265 static int cb710_mmc_receive(struct cb710_slot *slot, struct mmc_data *data) 266 { 267 struct sg_mapping_iter miter; 268 size_t len, blocks = data->blocks; 269 int err = 0; 270 271 /* TODO: I don't know how/if the hardware handles non-16B-boundary blocks 272 * except single 8B block */ 273 if (unlikely(data->blksz & 15 && (data->blocks != 1 || data->blksz != 8))) 274 return -EINVAL; 275 276 sg_miter_start(&miter, data->sg, data->sg_len, SG_MITER_TO_SG); 277 278 cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT, 279 15, CB710_MMC_C2_READ_PIO_SIZE_MASK); 280 281 cb710_mmc_fifo_hack(slot); 282 283 while (blocks-- > 0) { 284 len = data->blksz; 285 286 while (len >= 16) { 287 err = cb710_mmc_receive_pio(slot, &miter, 4); 288 if (err) 289 goto out; 290 len -= 16; 291 } 292 293 if (!len) 294 continue; 295 296 cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT, 297 len - 1, CB710_MMC_C2_READ_PIO_SIZE_MASK); 298 299 len = (len >= 8) ? 4 : 2; 300 err = cb710_mmc_receive_pio(slot, &miter, len); 301 if (err) 302 goto out; 303 } 304 out: 305 sg_miter_stop(&miter); 306 return err; 307 } 308 309 static int cb710_mmc_send(struct cb710_slot *slot, struct mmc_data *data) 310 { 311 struct sg_mapping_iter miter; 312 size_t len, blocks = data->blocks; 313 int err = 0; 314 315 /* TODO: I don't know how/if the hardware handles multiple 316 * non-16B-boundary blocks */ 317 if (unlikely(data->blocks > 1 && data->blksz & 15)) 318 return -EINVAL; 319 320 sg_miter_start(&miter, data->sg, data->sg_len, SG_MITER_FROM_SG); 321 322 cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT, 323 0, CB710_MMC_C2_READ_PIO_SIZE_MASK); 324 325 while (blocks-- > 0) { 326 len = (data->blksz + 15) >> 4; 327 do { 328 if (!(cb710_read_port_8(slot, CB710_MMC_STATUS2_PORT) 329 & CB710_MMC_S2_FIFO_EMPTY)) { 330 err = cb710_wait_for_event(slot, 331 CB710_MMC_S1_PIO_TRANSFER_DONE); 332 if (err) 333 goto out; 334 } 335 cb710_sg_dwiter_read_to_io(&miter, 336 slot->iobase + CB710_MMC_DATA_PORT, 4); 337 } while (--len); 338 } 339 out: 340 sg_miter_stop(&miter); 341 return err; 342 } 343 344 static u16 cb710_encode_cmd_flags(struct cb710_mmc_reader *reader, 345 struct mmc_command *cmd) 346 { 347 unsigned int flags = cmd->flags; 348 u16 cb_flags = 0; 349 350 /* Windows driver returned 0 for commands for which no response 351 * is expected. It happened that there were only two such commands 352 * used: MMC_GO_IDLE_STATE and MMC_GO_INACTIVE_STATE so it might 353 * as well be a bug in that driver. 354 * 355 * Original driver set bit 14 for MMC/SD application 356 * commands. There's no difference 'on the wire' and 357 * it apparently works without it anyway. 358 */ 359 360 switch (flags & MMC_CMD_MASK) { 361 case MMC_CMD_AC: cb_flags = CB710_MMC_CMD_AC; break; 362 case MMC_CMD_ADTC: cb_flags = CB710_MMC_CMD_ADTC; break; 363 case MMC_CMD_BC: cb_flags = CB710_MMC_CMD_BC; break; 364 case MMC_CMD_BCR: cb_flags = CB710_MMC_CMD_BCR; break; 365 } 366 367 if (flags & MMC_RSP_BUSY) 368 cb_flags |= CB710_MMC_RSP_BUSY; 369 370 cb_flags |= cmd->opcode << CB710_MMC_CMD_CODE_SHIFT; 371 372 if (cmd->data && (cmd->data->flags & MMC_DATA_READ)) 373 cb_flags |= CB710_MMC_DATA_READ; 374 375 if (flags & MMC_RSP_PRESENT) { 376 /* Windows driver set 01 at bits 4,3 except for 377 * MMC_SET_BLOCKLEN where it set 10. Maybe the 378 * hardware can do something special about this 379 * command? The original driver looks buggy/incomplete 380 * anyway so we ignore this for now. 381 * 382 * I assume that 00 here means no response is expected. 383 */ 384 cb_flags |= CB710_MMC_RSP_PRESENT; 385 386 if (flags & MMC_RSP_136) 387 cb_flags |= CB710_MMC_RSP_136; 388 if (!(flags & MMC_RSP_CRC)) 389 cb_flags |= CB710_MMC_RSP_NO_CRC; 390 } 391 392 return cb_flags; 393 } 394 395 static void cb710_receive_response(struct cb710_slot *slot, 396 struct mmc_command *cmd) 397 { 398 unsigned rsp_opcode, wanted_opcode; 399 400 /* Looks like final byte with CRC is always stripped (same as SDHCI) */ 401 if (cmd->flags & MMC_RSP_136) { 402 u32 resp[4]; 403 404 resp[0] = cb710_read_port_32(slot, CB710_MMC_RESPONSE3_PORT); 405 resp[1] = cb710_read_port_32(slot, CB710_MMC_RESPONSE2_PORT); 406 resp[2] = cb710_read_port_32(slot, CB710_MMC_RESPONSE1_PORT); 407 resp[3] = cb710_read_port_32(slot, CB710_MMC_RESPONSE0_PORT); 408 rsp_opcode = resp[0] >> 24; 409 410 cmd->resp[0] = (resp[0] << 8)|(resp[1] >> 24); 411 cmd->resp[1] = (resp[1] << 8)|(resp[2] >> 24); 412 cmd->resp[2] = (resp[2] << 8)|(resp[3] >> 24); 413 cmd->resp[3] = (resp[3] << 8); 414 } else { 415 rsp_opcode = cb710_read_port_32(slot, CB710_MMC_RESPONSE1_PORT) & 0x3F; 416 cmd->resp[0] = cb710_read_port_32(slot, CB710_MMC_RESPONSE0_PORT); 417 } 418 419 wanted_opcode = (cmd->flags & MMC_RSP_OPCODE) ? cmd->opcode : 0x3F; 420 if (rsp_opcode != wanted_opcode) 421 cmd->error = -EILSEQ; 422 } 423 424 static int cb710_mmc_transfer_data(struct cb710_slot *slot, 425 struct mmc_data *data) 426 { 427 int error, to; 428 429 if (data->flags & MMC_DATA_READ) 430 error = cb710_mmc_receive(slot, data); 431 else 432 error = cb710_mmc_send(slot, data); 433 434 to = cb710_wait_for_event(slot, CB710_MMC_S1_DATA_TRANSFER_DONE); 435 if (!error) 436 error = to; 437 438 if (!error) 439 data->bytes_xfered = data->blksz * data->blocks; 440 return error; 441 } 442 443 static int cb710_mmc_command(struct mmc_host *mmc, struct mmc_command *cmd) 444 { 445 struct cb710_slot *slot = cb710_mmc_to_slot(mmc); 446 struct cb710_mmc_reader *reader = mmc_priv(mmc); 447 struct mmc_data *data = cmd->data; 448 449 u16 cb_cmd = cb710_encode_cmd_flags(reader, cmd); 450 dev_dbg(cb710_slot_dev(slot), "cmd request: 0x%04X\n", cb_cmd); 451 452 if (data) { 453 if (!cb710_is_transfer_size_supported(data)) { 454 data->error = -EINVAL; 455 return -1; 456 } 457 cb710_mmc_set_transfer_size(slot, data->blocks, data->blksz); 458 } 459 460 cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20|CB710_MMC_S2_BUSY_10); 461 cb710_write_port_16(slot, CB710_MMC_CMD_TYPE_PORT, cb_cmd); 462 cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20); 463 cb710_write_port_32(slot, CB710_MMC_CMD_PARAM_PORT, cmd->arg); 464 cb710_mmc_reset_events(slot); 465 cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20); 466 cb710_modify_port_8(slot, CB710_MMC_CONFIG0_PORT, 0x01, 0); 467 468 cmd->error = cb710_wait_for_event(slot, CB710_MMC_S1_COMMAND_SENT); 469 if (cmd->error) 470 return -1; 471 472 if (cmd->flags & MMC_RSP_PRESENT) { 473 cb710_receive_response(slot, cmd); 474 if (cmd->error) 475 return -1; 476 } 477 478 if (data) 479 data->error = cb710_mmc_transfer_data(slot, data); 480 return 0; 481 } 482 483 static void cb710_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq) 484 { 485 struct cb710_slot *slot = cb710_mmc_to_slot(mmc); 486 struct cb710_mmc_reader *reader = mmc_priv(mmc); 487 488 WARN_ON(reader->mrq != NULL); 489 490 reader->mrq = mrq; 491 cb710_mmc_enable_irq(slot, CB710_MMC_IE_TEST_MASK, 0); 492 493 if (!cb710_mmc_command(mmc, mrq->cmd) && mrq->stop) 494 cb710_mmc_command(mmc, mrq->stop); 495 496 tasklet_schedule(&reader->finish_req_tasklet); 497 } 498 499 static int cb710_mmc_powerup(struct cb710_slot *slot) 500 { 501 #ifdef CONFIG_CB710_DEBUG 502 struct cb710_chip *chip = cb710_slot_to_chip(slot); 503 #endif 504 int err; 505 506 /* a lot of magic for now */ 507 dev_dbg(cb710_slot_dev(slot), "bus powerup\n"); 508 cb710_dump_regs(chip, CB710_DUMP_REGS_MMC); 509 err = cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20); 510 if (unlikely(err)) 511 return err; 512 cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT, 0x80, 0); 513 cb710_modify_port_8(slot, CB710_MMC_CONFIG3_PORT, 0x80, 0); 514 cb710_dump_regs(chip, CB710_DUMP_REGS_MMC); 515 mdelay(1); 516 dev_dbg(cb710_slot_dev(slot), "after delay 1\n"); 517 cb710_dump_regs(chip, CB710_DUMP_REGS_MMC); 518 err = cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20); 519 if (unlikely(err)) 520 return err; 521 cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT, 0x09, 0); 522 cb710_dump_regs(chip, CB710_DUMP_REGS_MMC); 523 mdelay(1); 524 dev_dbg(cb710_slot_dev(slot), "after delay 2\n"); 525 cb710_dump_regs(chip, CB710_DUMP_REGS_MMC); 526 err = cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20); 527 if (unlikely(err)) 528 return err; 529 cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT, 0, 0x08); 530 cb710_dump_regs(chip, CB710_DUMP_REGS_MMC); 531 mdelay(2); 532 dev_dbg(cb710_slot_dev(slot), "after delay 3\n"); 533 cb710_dump_regs(chip, CB710_DUMP_REGS_MMC); 534 cb710_modify_port_8(slot, CB710_MMC_CONFIG0_PORT, 0x06, 0); 535 cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT, 0x70, 0); 536 cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT, 0x80, 0); 537 cb710_modify_port_8(slot, CB710_MMC_CONFIG3_PORT, 0x03, 0); 538 cb710_dump_regs(chip, CB710_DUMP_REGS_MMC); 539 err = cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20); 540 if (unlikely(err)) 541 return err; 542 /* This port behaves weird: quick byte reads of 0x08,0x09 return 543 * 0xFF,0x00 after writing 0xFFFF to 0x08; it works correctly when 544 * read/written from userspace... What am I missing here? 545 * (it doesn't depend on write-to-read delay) */ 546 cb710_write_port_16(slot, CB710_MMC_CONFIGB_PORT, 0xFFFF); 547 cb710_modify_port_8(slot, CB710_MMC_CONFIG0_PORT, 0x06, 0); 548 cb710_dump_regs(chip, CB710_DUMP_REGS_MMC); 549 dev_dbg(cb710_slot_dev(slot), "bus powerup finished\n"); 550 551 return cb710_check_event(slot, 0); 552 } 553 554 static void cb710_mmc_powerdown(struct cb710_slot *slot) 555 { 556 cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT, 0, 0x81); 557 cb710_modify_port_8(slot, CB710_MMC_CONFIG3_PORT, 0, 0x80); 558 } 559 560 static void cb710_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) 561 { 562 struct cb710_slot *slot = cb710_mmc_to_slot(mmc); 563 struct cb710_mmc_reader *reader = mmc_priv(mmc); 564 int err; 565 566 cb710_mmc_select_clock_divider(mmc, ios->clock); 567 568 if (ios->power_mode != reader->last_power_mode) { 569 switch (ios->power_mode) { 570 case MMC_POWER_ON: 571 err = cb710_mmc_powerup(slot); 572 if (err) { 573 dev_warn(cb710_slot_dev(slot), 574 "powerup failed (%d)- retrying\n", err); 575 cb710_mmc_powerdown(slot); 576 udelay(1); 577 err = cb710_mmc_powerup(slot); 578 if (err) 579 dev_warn(cb710_slot_dev(slot), 580 "powerup retry failed (%d) - expect errors\n", 581 err); 582 } 583 reader->last_power_mode = MMC_POWER_ON; 584 break; 585 case MMC_POWER_OFF: 586 cb710_mmc_powerdown(slot); 587 reader->last_power_mode = MMC_POWER_OFF; 588 break; 589 case MMC_POWER_UP: 590 default: 591 /* ignore */ 592 break; 593 } 594 } 595 596 cb710_mmc_enable_4bit_data(slot, ios->bus_width != MMC_BUS_WIDTH_1); 597 598 cb710_mmc_enable_irq(slot, CB710_MMC_IE_TEST_MASK, 0); 599 } 600 601 static int cb710_mmc_get_ro(struct mmc_host *mmc) 602 { 603 struct cb710_slot *slot = cb710_mmc_to_slot(mmc); 604 605 return cb710_read_port_8(slot, CB710_MMC_STATUS3_PORT) 606 & CB710_MMC_S3_WRITE_PROTECTED; 607 } 608 609 static int cb710_mmc_get_cd(struct mmc_host *mmc) 610 { 611 struct cb710_slot *slot = cb710_mmc_to_slot(mmc); 612 613 return cb710_read_port_8(slot, CB710_MMC_STATUS3_PORT) 614 & CB710_MMC_S3_CARD_DETECTED; 615 } 616 617 static int cb710_mmc_irq_handler(struct cb710_slot *slot) 618 { 619 struct mmc_host *mmc = cb710_slot_to_mmc(slot); 620 struct cb710_mmc_reader *reader = mmc_priv(mmc); 621 u32 status, config1, config2, irqen; 622 623 status = cb710_read_port_32(slot, CB710_MMC_STATUS_PORT); 624 irqen = cb710_read_port_32(slot, CB710_MMC_IRQ_ENABLE_PORT); 625 config2 = cb710_read_port_32(slot, CB710_MMC_CONFIGB_PORT); 626 config1 = cb710_read_port_32(slot, CB710_MMC_CONFIG_PORT); 627 628 dev_dbg(cb710_slot_dev(slot), "interrupt; status: %08X, " 629 "ie: %08X, c2: %08X, c1: %08X\n", 630 status, irqen, config2, config1); 631 632 if (status & (CB710_MMC_S1_CARD_CHANGED << 8)) { 633 /* ack the event */ 634 cb710_write_port_8(slot, CB710_MMC_STATUS1_PORT, 635 CB710_MMC_S1_CARD_CHANGED); 636 if ((irqen & CB710_MMC_IE_CISTATUS_MASK) 637 == CB710_MMC_IE_CISTATUS_MASK) 638 mmc_detect_change(mmc, HZ/5); 639 } else { 640 dev_dbg(cb710_slot_dev(slot), "unknown interrupt (test)\n"); 641 spin_lock(&reader->irq_lock); 642 __cb710_mmc_enable_irq(slot, 0, CB710_MMC_IE_TEST_MASK); 643 spin_unlock(&reader->irq_lock); 644 } 645 646 return 1; 647 } 648 649 static void cb710_mmc_finish_request_tasklet(struct tasklet_struct *t) 650 { 651 struct cb710_mmc_reader *reader = from_tasklet(reader, t, 652 finish_req_tasklet); 653 struct mmc_request *mrq = reader->mrq; 654 655 reader->mrq = NULL; 656 mmc_request_done(mmc_from_priv(reader), mrq); 657 } 658 659 static const struct mmc_host_ops cb710_mmc_host = { 660 .request = cb710_mmc_request, 661 .set_ios = cb710_mmc_set_ios, 662 .get_ro = cb710_mmc_get_ro, 663 .get_cd = cb710_mmc_get_cd, 664 }; 665 666 #ifdef CONFIG_PM 667 668 static int cb710_mmc_suspend(struct platform_device *pdev, pm_message_t state) 669 { 670 struct cb710_slot *slot = cb710_pdev_to_slot(pdev); 671 672 cb710_mmc_enable_irq(slot, 0, ~0); 673 return 0; 674 } 675 676 static int cb710_mmc_resume(struct platform_device *pdev) 677 { 678 struct cb710_slot *slot = cb710_pdev_to_slot(pdev); 679 680 cb710_mmc_enable_irq(slot, 0, ~0); 681 return 0; 682 } 683 684 #endif /* CONFIG_PM */ 685 686 static int cb710_mmc_init(struct platform_device *pdev) 687 { 688 struct cb710_slot *slot = cb710_pdev_to_slot(pdev); 689 struct cb710_chip *chip = cb710_slot_to_chip(slot); 690 struct mmc_host *mmc; 691 struct cb710_mmc_reader *reader; 692 int err; 693 u32 val; 694 695 mmc = mmc_alloc_host(sizeof(*reader), cb710_slot_dev(slot)); 696 if (!mmc) 697 return -ENOMEM; 698 699 platform_set_drvdata(pdev, mmc); 700 701 /* harmless (maybe) magic */ 702 pci_read_config_dword(chip->pdev, 0x48, &val); 703 val = cb710_src_freq_mhz[(val >> 16) & 0xF]; 704 dev_dbg(cb710_slot_dev(slot), "source frequency: %dMHz\n", val); 705 val *= 1000000; 706 707 mmc->ops = &cb710_mmc_host; 708 mmc->f_max = val; 709 mmc->f_min = val >> cb710_clock_divider_log2[CB710_MAX_DIVIDER_IDX]; 710 mmc->ocr_avail = MMC_VDD_32_33|MMC_VDD_33_34; 711 mmc->caps = MMC_CAP_4_BIT_DATA; 712 /* 713 * In cb710_wait_for_event() we use a fixed timeout of ~2s, hence let's 714 * inform the core about it. A future improvement should instead make 715 * use of the cmd->busy_timeout. 716 */ 717 mmc->max_busy_timeout = CB710_MMC_REQ_TIMEOUT_MS; 718 719 reader = mmc_priv(mmc); 720 721 tasklet_setup(&reader->finish_req_tasklet, 722 cb710_mmc_finish_request_tasklet); 723 spin_lock_init(&reader->irq_lock); 724 cb710_dump_regs(chip, CB710_DUMP_REGS_MMC); 725 726 cb710_mmc_enable_irq(slot, 0, ~0); 727 cb710_set_irq_handler(slot, cb710_mmc_irq_handler); 728 729 err = mmc_add_host(mmc); 730 if (unlikely(err)) 731 goto err_free_mmc; 732 733 dev_dbg(cb710_slot_dev(slot), "mmc_hostname is %s\n", 734 mmc_hostname(mmc)); 735 736 cb710_mmc_enable_irq(slot, CB710_MMC_IE_CARD_INSERTION_STATUS, 0); 737 738 return 0; 739 740 err_free_mmc: 741 dev_dbg(cb710_slot_dev(slot), "mmc_add_host() failed: %d\n", err); 742 743 cb710_set_irq_handler(slot, NULL); 744 mmc_free_host(mmc); 745 return err; 746 } 747 748 static void cb710_mmc_exit(struct platform_device *pdev) 749 { 750 struct cb710_slot *slot = cb710_pdev_to_slot(pdev); 751 struct mmc_host *mmc = cb710_slot_to_mmc(slot); 752 struct cb710_mmc_reader *reader = mmc_priv(mmc); 753 754 cb710_mmc_enable_irq(slot, 0, CB710_MMC_IE_CARD_INSERTION_STATUS); 755 756 mmc_remove_host(mmc); 757 758 /* IRQs should be disabled now, but let's stay on the safe side */ 759 cb710_mmc_enable_irq(slot, 0, ~0); 760 cb710_set_irq_handler(slot, NULL); 761 762 /* clear config ports - just in case */ 763 cb710_write_port_32(slot, CB710_MMC_CONFIG_PORT, 0); 764 cb710_write_port_16(slot, CB710_MMC_CONFIGB_PORT, 0); 765 766 tasklet_kill(&reader->finish_req_tasklet); 767 768 mmc_free_host(mmc); 769 } 770 771 static struct platform_driver cb710_mmc_driver = { 772 .driver.name = "cb710-mmc", 773 .probe = cb710_mmc_init, 774 .remove_new = cb710_mmc_exit, 775 #ifdef CONFIG_PM 776 .suspend = cb710_mmc_suspend, 777 .resume = cb710_mmc_resume, 778 #endif 779 }; 780 781 module_platform_driver(cb710_mmc_driver); 782 783 MODULE_AUTHOR("Michał Mirosław <mirq-linux@rere.qmqm.pl>"); 784 MODULE_DESCRIPTION("ENE CB710 memory card reader driver - MMC/SD part"); 785 MODULE_LICENSE("GPL"); 786 MODULE_ALIAS("platform:cb710-mmc"); 787