1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * linux/drivers/mmc/host/au1xmmc.c - AU1XX0 MMC driver 4 * 5 * Copyright (c) 2005, Advanced Micro Devices, Inc. 6 * 7 * Developed with help from the 2.4.30 MMC AU1XXX controller including 8 * the following copyright notices: 9 * Copyright (c) 2003-2004 Embedded Edge, LLC. 10 * Portions Copyright (C) 2002 Embedix, Inc 11 * Copyright 2002 Hewlett-Packard Company 12 13 * 2.6 version of this driver inspired by: 14 * (drivers/mmc/wbsd.c) Copyright (C) 2004-2005 Pierre Ossman, 15 * All Rights Reserved. 16 * (drivers/mmc/pxa.c) Copyright (C) 2003 Russell King, 17 * All Rights Reserved. 18 * 19 20 */ 21 22 /* Why don't we use the SD controllers' carddetect feature? 23 * 24 * From the AU1100 MMC application guide: 25 * If the Au1100-based design is intended to support both MultiMediaCards 26 * and 1- or 4-data bit SecureDigital cards, then the solution is to 27 * connect a weak (560KOhm) pull-up resistor to connector pin 1. 28 * In doing so, a MMC card never enters SPI-mode communications, 29 * but now the SecureDigital card-detect feature of CD/DAT3 is ineffective 30 * (the low to high transition will not occur). 31 */ 32 33 #include <linux/clk.h> 34 #include <linux/module.h> 35 #include <linux/init.h> 36 #include <linux/platform_device.h> 37 #include <linux/mm.h> 38 #include <linux/interrupt.h> 39 #include <linux/dma-mapping.h> 40 #include <linux/scatterlist.h> 41 #include <linux/highmem.h> 42 #include <linux/leds.h> 43 #include <linux/mmc/host.h> 44 #include <linux/slab.h> 45 46 #include <asm/io.h> 47 #include <asm/mach-au1x00/au1000.h> 48 #include <asm/mach-au1x00/au1xxx_dbdma.h> 49 #include <asm/mach-au1x00/au1100_mmc.h> 50 51 #define DRIVER_NAME "au1xxx-mmc" 52 53 /* Set this to enable special debugging macros */ 54 /* #define DEBUG */ 55 56 #ifdef DEBUG 57 #define DBG(fmt, idx, args...) \ 58 pr_debug("au1xmmc(%d): DEBUG: " fmt, idx, ##args) 59 #else 60 #define DBG(fmt, idx, args...) do {} while (0) 61 #endif 62 63 /* Hardware definitions */ 64 #define AU1XMMC_DESCRIPTOR_COUNT 1 65 66 /* max DMA seg size: 64KB on Au1100, 4MB on Au1200 */ 67 #define AU1100_MMC_DESCRIPTOR_SIZE 0x0000ffff 68 #define AU1200_MMC_DESCRIPTOR_SIZE 0x003fffff 69 70 #define AU1XMMC_OCR (MMC_VDD_27_28 | MMC_VDD_28_29 | MMC_VDD_29_30 | \ 71 MMC_VDD_30_31 | MMC_VDD_31_32 | MMC_VDD_32_33 | \ 72 MMC_VDD_33_34 | MMC_VDD_34_35 | MMC_VDD_35_36) 73 74 /* This gives us a hard value for the stop command that we can write directly 75 * to the command register. 76 */ 77 #define STOP_CMD \ 78 (SD_CMD_RT_1B | SD_CMD_CT_7 | (0xC << SD_CMD_CI_SHIFT) | SD_CMD_GO) 79 80 /* This is the set of interrupts that we configure by default. */ 81 #define AU1XMMC_INTERRUPTS \ 82 (SD_CONFIG_SC | SD_CONFIG_DT | SD_CONFIG_RAT | \ 83 SD_CONFIG_CR | SD_CONFIG_I) 84 85 /* The poll event (looking for insert/remove events runs twice a second. */ 86 #define AU1XMMC_DETECT_TIMEOUT (HZ/2) 87 88 struct au1xmmc_host { 89 struct mmc_host *mmc; 90 struct mmc_request *mrq; 91 92 u32 flags; 93 void __iomem *iobase; 94 u32 clock; 95 u32 bus_width; 96 u32 power_mode; 97 98 int status; 99 100 struct { 101 int len; 102 int dir; 103 } dma; 104 105 struct { 106 int index; 107 int offset; 108 int len; 109 } pio; 110 111 u32 tx_chan; 112 u32 rx_chan; 113 114 int irq; 115 116 struct tasklet_struct finish_task; 117 struct tasklet_struct data_task; 118 struct au1xmmc_platform_data *platdata; 119 struct platform_device *pdev; 120 struct resource *ioarea; 121 struct clk *clk; 122 }; 123 124 /* Status flags used by the host structure */ 125 #define HOST_F_XMIT 0x0001 126 #define HOST_F_RECV 0x0002 127 #define HOST_F_DMA 0x0010 128 #define HOST_F_DBDMA 0x0020 129 #define HOST_F_ACTIVE 0x0100 130 #define HOST_F_STOP 0x1000 131 132 #define HOST_S_IDLE 0x0001 133 #define HOST_S_CMD 0x0002 134 #define HOST_S_DATA 0x0003 135 #define HOST_S_STOP 0x0004 136 137 /* Easy access macros */ 138 #define HOST_STATUS(h) ((h)->iobase + SD_STATUS) 139 #define HOST_CONFIG(h) ((h)->iobase + SD_CONFIG) 140 #define HOST_ENABLE(h) ((h)->iobase + SD_ENABLE) 141 #define HOST_TXPORT(h) ((h)->iobase + SD_TXPORT) 142 #define HOST_RXPORT(h) ((h)->iobase + SD_RXPORT) 143 #define HOST_CMDARG(h) ((h)->iobase + SD_CMDARG) 144 #define HOST_BLKSIZE(h) ((h)->iobase + SD_BLKSIZE) 145 #define HOST_CMD(h) ((h)->iobase + SD_CMD) 146 #define HOST_CONFIG2(h) ((h)->iobase + SD_CONFIG2) 147 #define HOST_TIMEOUT(h) ((h)->iobase + SD_TIMEOUT) 148 #define HOST_DEBUG(h) ((h)->iobase + SD_DEBUG) 149 150 #define DMA_CHANNEL(h) \ 151 (((h)->flags & HOST_F_XMIT) ? (h)->tx_chan : (h)->rx_chan) 152 153 static inline int has_dbdma(void) 154 { 155 switch (alchemy_get_cputype()) { 156 case ALCHEMY_CPU_AU1200: 157 case ALCHEMY_CPU_AU1300: 158 return 1; 159 default: 160 return 0; 161 } 162 } 163 164 static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask) 165 { 166 u32 val = __raw_readl(HOST_CONFIG(host)); 167 val |= mask; 168 __raw_writel(val, HOST_CONFIG(host)); 169 wmb(); /* drain writebuffer */ 170 } 171 172 static inline void FLUSH_FIFO(struct au1xmmc_host *host) 173 { 174 u32 val = __raw_readl(HOST_CONFIG2(host)); 175 176 __raw_writel(val | SD_CONFIG2_FF, HOST_CONFIG2(host)); 177 wmb(); /* drain writebuffer */ 178 mdelay(1); 179 180 /* SEND_STOP will turn off clock control - this re-enables it */ 181 val &= ~SD_CONFIG2_DF; 182 183 __raw_writel(val, HOST_CONFIG2(host)); 184 wmb(); /* drain writebuffer */ 185 } 186 187 static inline void IRQ_OFF(struct au1xmmc_host *host, u32 mask) 188 { 189 u32 val = __raw_readl(HOST_CONFIG(host)); 190 val &= ~mask; 191 __raw_writel(val, HOST_CONFIG(host)); 192 wmb(); /* drain writebuffer */ 193 } 194 195 static inline void SEND_STOP(struct au1xmmc_host *host) 196 { 197 u32 config2; 198 199 WARN_ON(host->status != HOST_S_DATA); 200 host->status = HOST_S_STOP; 201 202 config2 = __raw_readl(HOST_CONFIG2(host)); 203 __raw_writel(config2 | SD_CONFIG2_DF, HOST_CONFIG2(host)); 204 wmb(); /* drain writebuffer */ 205 206 /* Send the stop command */ 207 __raw_writel(STOP_CMD, HOST_CMD(host)); 208 wmb(); /* drain writebuffer */ 209 } 210 211 static void au1xmmc_set_power(struct au1xmmc_host *host, int state) 212 { 213 if (host->platdata && host->platdata->set_power) 214 host->platdata->set_power(host->mmc, state); 215 } 216 217 static int au1xmmc_card_inserted(struct mmc_host *mmc) 218 { 219 struct au1xmmc_host *host = mmc_priv(mmc); 220 221 if (host->platdata && host->platdata->card_inserted) 222 return !!host->platdata->card_inserted(host->mmc); 223 224 return -ENOSYS; 225 } 226 227 static int au1xmmc_card_readonly(struct mmc_host *mmc) 228 { 229 struct au1xmmc_host *host = mmc_priv(mmc); 230 231 if (host->platdata && host->platdata->card_readonly) 232 return !!host->platdata->card_readonly(mmc); 233 234 return -ENOSYS; 235 } 236 237 static void au1xmmc_finish_request(struct au1xmmc_host *host) 238 { 239 struct mmc_request *mrq = host->mrq; 240 241 host->mrq = NULL; 242 host->flags &= HOST_F_ACTIVE | HOST_F_DMA; 243 244 host->dma.len = 0; 245 host->dma.dir = 0; 246 247 host->pio.index = 0; 248 host->pio.offset = 0; 249 host->pio.len = 0; 250 251 host->status = HOST_S_IDLE; 252 253 mmc_request_done(host->mmc, mrq); 254 } 255 256 static void au1xmmc_tasklet_finish(unsigned long param) 257 { 258 struct au1xmmc_host *host = (struct au1xmmc_host *) param; 259 au1xmmc_finish_request(host); 260 } 261 262 static int au1xmmc_send_command(struct au1xmmc_host *host, int wait, 263 struct mmc_command *cmd, struct mmc_data *data) 264 { 265 u32 mmccmd = (cmd->opcode << SD_CMD_CI_SHIFT); 266 267 switch (mmc_resp_type(cmd)) { 268 case MMC_RSP_NONE: 269 break; 270 case MMC_RSP_R1: 271 mmccmd |= SD_CMD_RT_1; 272 break; 273 case MMC_RSP_R1B: 274 mmccmd |= SD_CMD_RT_1B; 275 break; 276 case MMC_RSP_R2: 277 mmccmd |= SD_CMD_RT_2; 278 break; 279 case MMC_RSP_R3: 280 mmccmd |= SD_CMD_RT_3; 281 break; 282 default: 283 pr_info("au1xmmc: unhandled response type %02x\n", 284 mmc_resp_type(cmd)); 285 return -EINVAL; 286 } 287 288 if (data) { 289 if (data->flags & MMC_DATA_READ) { 290 if (data->blocks > 1) 291 mmccmd |= SD_CMD_CT_4; 292 else 293 mmccmd |= SD_CMD_CT_2; 294 } else if (data->flags & MMC_DATA_WRITE) { 295 if (data->blocks > 1) 296 mmccmd |= SD_CMD_CT_3; 297 else 298 mmccmd |= SD_CMD_CT_1; 299 } 300 } 301 302 __raw_writel(cmd->arg, HOST_CMDARG(host)); 303 wmb(); /* drain writebuffer */ 304 305 if (wait) 306 IRQ_OFF(host, SD_CONFIG_CR); 307 308 __raw_writel((mmccmd | SD_CMD_GO), HOST_CMD(host)); 309 wmb(); /* drain writebuffer */ 310 311 /* Wait for the command to go on the line */ 312 while (__raw_readl(HOST_CMD(host)) & SD_CMD_GO) 313 /* nop */; 314 315 /* Wait for the command to come back */ 316 if (wait) { 317 u32 status = __raw_readl(HOST_STATUS(host)); 318 319 while (!(status & SD_STATUS_CR)) 320 status = __raw_readl(HOST_STATUS(host)); 321 322 /* Clear the CR status */ 323 __raw_writel(SD_STATUS_CR, HOST_STATUS(host)); 324 325 IRQ_ON(host, SD_CONFIG_CR); 326 } 327 328 return 0; 329 } 330 331 static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) 332 { 333 struct mmc_request *mrq = host->mrq; 334 struct mmc_data *data; 335 u32 crc; 336 337 WARN_ON((host->status != HOST_S_DATA) && (host->status != HOST_S_STOP)); 338 339 if (host->mrq == NULL) 340 return; 341 342 data = mrq->cmd->data; 343 344 if (status == 0) 345 status = __raw_readl(HOST_STATUS(host)); 346 347 /* The transaction is really over when the SD_STATUS_DB bit is clear */ 348 while ((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB)) 349 status = __raw_readl(HOST_STATUS(host)); 350 351 data->error = 0; 352 dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir); 353 354 /* Process any errors */ 355 crc = (status & (SD_STATUS_WC | SD_STATUS_RC)); 356 if (host->flags & HOST_F_XMIT) 357 crc |= ((status & 0x07) == 0x02) ? 0 : 1; 358 359 if (crc) 360 data->error = -EILSEQ; 361 362 /* Clear the CRC bits */ 363 __raw_writel(SD_STATUS_WC | SD_STATUS_RC, HOST_STATUS(host)); 364 365 data->bytes_xfered = 0; 366 367 if (!data->error) { 368 if (host->flags & (HOST_F_DMA | HOST_F_DBDMA)) { 369 u32 chan = DMA_CHANNEL(host); 370 371 chan_tab_t *c = *((chan_tab_t **)chan); 372 au1x_dma_chan_t *cp = c->chan_ptr; 373 data->bytes_xfered = cp->ddma_bytecnt; 374 } else 375 data->bytes_xfered = 376 (data->blocks * data->blksz) - host->pio.len; 377 } 378 379 au1xmmc_finish_request(host); 380 } 381 382 static void au1xmmc_tasklet_data(unsigned long param) 383 { 384 struct au1xmmc_host *host = (struct au1xmmc_host *)param; 385 386 u32 status = __raw_readl(HOST_STATUS(host)); 387 au1xmmc_data_complete(host, status); 388 } 389 390 #define AU1XMMC_MAX_TRANSFER 8 391 392 static void au1xmmc_send_pio(struct au1xmmc_host *host) 393 { 394 struct mmc_data *data; 395 int sg_len, max, count; 396 unsigned char *sg_ptr, val; 397 u32 status; 398 struct scatterlist *sg; 399 400 data = host->mrq->data; 401 402 if (!(host->flags & HOST_F_XMIT)) 403 return; 404 405 /* This is the pointer to the data buffer */ 406 sg = &data->sg[host->pio.index]; 407 sg_ptr = kmap_atomic(sg_page(sg)) + sg->offset + host->pio.offset; 408 409 /* This is the space left inside the buffer */ 410 sg_len = data->sg[host->pio.index].length - host->pio.offset; 411 412 /* Check if we need less than the size of the sg_buffer */ 413 max = (sg_len > host->pio.len) ? host->pio.len : sg_len; 414 if (max > AU1XMMC_MAX_TRANSFER) 415 max = AU1XMMC_MAX_TRANSFER; 416 417 for (count = 0; count < max; count++) { 418 status = __raw_readl(HOST_STATUS(host)); 419 420 if (!(status & SD_STATUS_TH)) 421 break; 422 423 val = sg_ptr[count]; 424 425 __raw_writel((unsigned long)val, HOST_TXPORT(host)); 426 wmb(); /* drain writebuffer */ 427 } 428 kunmap_atomic(sg_ptr); 429 430 host->pio.len -= count; 431 host->pio.offset += count; 432 433 if (count == sg_len) { 434 host->pio.index++; 435 host->pio.offset = 0; 436 } 437 438 if (host->pio.len == 0) { 439 IRQ_OFF(host, SD_CONFIG_TH); 440 441 if (host->flags & HOST_F_STOP) 442 SEND_STOP(host); 443 444 tasklet_schedule(&host->data_task); 445 } 446 } 447 448 static void au1xmmc_receive_pio(struct au1xmmc_host *host) 449 { 450 struct mmc_data *data; 451 int max, count, sg_len = 0; 452 unsigned char *sg_ptr = NULL; 453 u32 status, val; 454 struct scatterlist *sg; 455 456 data = host->mrq->data; 457 458 if (!(host->flags & HOST_F_RECV)) 459 return; 460 461 max = host->pio.len; 462 463 if (host->pio.index < host->dma.len) { 464 sg = &data->sg[host->pio.index]; 465 sg_ptr = kmap_atomic(sg_page(sg)) + sg->offset + host->pio.offset; 466 467 /* This is the space left inside the buffer */ 468 sg_len = sg_dma_len(&data->sg[host->pio.index]) - host->pio.offset; 469 470 /* Check if we need less than the size of the sg_buffer */ 471 if (sg_len < max) 472 max = sg_len; 473 } 474 475 if (max > AU1XMMC_MAX_TRANSFER) 476 max = AU1XMMC_MAX_TRANSFER; 477 478 for (count = 0; count < max; count++) { 479 status = __raw_readl(HOST_STATUS(host)); 480 481 if (!(status & SD_STATUS_NE)) 482 break; 483 484 if (status & SD_STATUS_RC) { 485 DBG("RX CRC Error [%d + %d].\n", host->pdev->id, 486 host->pio.len, count); 487 break; 488 } 489 490 if (status & SD_STATUS_RO) { 491 DBG("RX Overrun [%d + %d]\n", host->pdev->id, 492 host->pio.len, count); 493 break; 494 } 495 else if (status & SD_STATUS_RU) { 496 DBG("RX Underrun [%d + %d]\n", host->pdev->id, 497 host->pio.len, count); 498 break; 499 } 500 501 val = __raw_readl(HOST_RXPORT(host)); 502 503 if (sg_ptr) 504 sg_ptr[count] = (unsigned char)(val & 0xFF); 505 } 506 if (sg_ptr) 507 kunmap_atomic(sg_ptr); 508 509 host->pio.len -= count; 510 host->pio.offset += count; 511 512 if (sg_len && count == sg_len) { 513 host->pio.index++; 514 host->pio.offset = 0; 515 } 516 517 if (host->pio.len == 0) { 518 /* IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF); */ 519 IRQ_OFF(host, SD_CONFIG_NE); 520 521 if (host->flags & HOST_F_STOP) 522 SEND_STOP(host); 523 524 tasklet_schedule(&host->data_task); 525 } 526 } 527 528 /* This is called when a command has been completed - grab the response 529 * and check for errors. Then start the data transfer if it is indicated. 530 */ 531 static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) 532 { 533 struct mmc_request *mrq = host->mrq; 534 struct mmc_command *cmd; 535 u32 r[4]; 536 int i, trans; 537 538 if (!host->mrq) 539 return; 540 541 cmd = mrq->cmd; 542 cmd->error = 0; 543 544 if (cmd->flags & MMC_RSP_PRESENT) { 545 if (cmd->flags & MMC_RSP_136) { 546 r[0] = __raw_readl(host->iobase + SD_RESP3); 547 r[1] = __raw_readl(host->iobase + SD_RESP2); 548 r[2] = __raw_readl(host->iobase + SD_RESP1); 549 r[3] = __raw_readl(host->iobase + SD_RESP0); 550 551 /* The CRC is omitted from the response, so really 552 * we only got 120 bytes, but the engine expects 553 * 128 bits, so we have to shift things up. 554 */ 555 for (i = 0; i < 4; i++) { 556 cmd->resp[i] = (r[i] & 0x00FFFFFF) << 8; 557 if (i != 3) 558 cmd->resp[i] |= (r[i + 1] & 0xFF000000) >> 24; 559 } 560 } else { 561 /* Techincally, we should be getting all 48 bits of 562 * the response (SD_RESP1 + SD_RESP2), but because 563 * our response omits the CRC, our data ends up 564 * being shifted 8 bits to the right. In this case, 565 * that means that the OSR data starts at bit 31, 566 * so we can just read RESP0 and return that. 567 */ 568 cmd->resp[0] = __raw_readl(host->iobase + SD_RESP0); 569 } 570 } 571 572 /* Figure out errors */ 573 if (status & (SD_STATUS_SC | SD_STATUS_WC | SD_STATUS_RC)) 574 cmd->error = -EILSEQ; 575 576 trans = host->flags & (HOST_F_XMIT | HOST_F_RECV); 577 578 if (!trans || cmd->error) { 579 IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA | SD_CONFIG_RF); 580 tasklet_schedule(&host->finish_task); 581 return; 582 } 583 584 host->status = HOST_S_DATA; 585 586 if ((host->flags & (HOST_F_DMA | HOST_F_DBDMA))) { 587 u32 channel = DMA_CHANNEL(host); 588 589 /* Start the DBDMA as soon as the buffer gets something in it */ 590 591 if (host->flags & HOST_F_RECV) { 592 u32 mask = SD_STATUS_DB | SD_STATUS_NE; 593 594 while((status & mask) != mask) 595 status = __raw_readl(HOST_STATUS(host)); 596 } 597 598 au1xxx_dbdma_start(channel); 599 } 600 } 601 602 static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate) 603 { 604 unsigned int pbus = clk_get_rate(host->clk); 605 unsigned int divisor = ((pbus / rate) / 2) - 1; 606 u32 config; 607 608 config = __raw_readl(HOST_CONFIG(host)); 609 610 config &= ~(SD_CONFIG_DIV); 611 config |= (divisor & SD_CONFIG_DIV) | SD_CONFIG_DE; 612 613 __raw_writel(config, HOST_CONFIG(host)); 614 wmb(); /* drain writebuffer */ 615 } 616 617 static int au1xmmc_prepare_data(struct au1xmmc_host *host, 618 struct mmc_data *data) 619 { 620 int datalen = data->blocks * data->blksz; 621 622 if (data->flags & MMC_DATA_READ) 623 host->flags |= HOST_F_RECV; 624 else 625 host->flags |= HOST_F_XMIT; 626 627 if (host->mrq->stop) 628 host->flags |= HOST_F_STOP; 629 630 host->dma.dir = DMA_BIDIRECTIONAL; 631 632 host->dma.len = dma_map_sg(mmc_dev(host->mmc), data->sg, 633 data->sg_len, host->dma.dir); 634 635 if (host->dma.len == 0) 636 return -ETIMEDOUT; 637 638 __raw_writel(data->blksz - 1, HOST_BLKSIZE(host)); 639 640 if (host->flags & (HOST_F_DMA | HOST_F_DBDMA)) { 641 int i; 642 u32 channel = DMA_CHANNEL(host); 643 644 au1xxx_dbdma_stop(channel); 645 646 for (i = 0; i < host->dma.len; i++) { 647 u32 ret = 0, flags = DDMA_FLAGS_NOIE; 648 struct scatterlist *sg = &data->sg[i]; 649 int sg_len = sg->length; 650 651 int len = (datalen > sg_len) ? sg_len : datalen; 652 653 if (i == host->dma.len - 1) 654 flags = DDMA_FLAGS_IE; 655 656 if (host->flags & HOST_F_XMIT) { 657 ret = au1xxx_dbdma_put_source(channel, 658 sg_phys(sg), len, flags); 659 } else { 660 ret = au1xxx_dbdma_put_dest(channel, 661 sg_phys(sg), len, flags); 662 } 663 664 if (!ret) 665 goto dataerr; 666 667 datalen -= len; 668 } 669 } else { 670 host->pio.index = 0; 671 host->pio.offset = 0; 672 host->pio.len = datalen; 673 674 if (host->flags & HOST_F_XMIT) 675 IRQ_ON(host, SD_CONFIG_TH); 676 else 677 IRQ_ON(host, SD_CONFIG_NE); 678 /* IRQ_ON(host, SD_CONFIG_RA | SD_CONFIG_RF); */ 679 } 680 681 return 0; 682 683 dataerr: 684 dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, 685 host->dma.dir); 686 return -ETIMEDOUT; 687 } 688 689 /* This actually starts a command or data transaction */ 690 static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) 691 { 692 struct au1xmmc_host *host = mmc_priv(mmc); 693 int ret = 0; 694 695 WARN_ON(irqs_disabled()); 696 WARN_ON(host->status != HOST_S_IDLE); 697 698 host->mrq = mrq; 699 host->status = HOST_S_CMD; 700 701 /* fail request immediately if no card is present */ 702 if (0 == au1xmmc_card_inserted(mmc)) { 703 mrq->cmd->error = -ENOMEDIUM; 704 au1xmmc_finish_request(host); 705 return; 706 } 707 708 if (mrq->data) { 709 FLUSH_FIFO(host); 710 ret = au1xmmc_prepare_data(host, mrq->data); 711 } 712 713 if (!ret) 714 ret = au1xmmc_send_command(host, 0, mrq->cmd, mrq->data); 715 716 if (ret) { 717 mrq->cmd->error = ret; 718 au1xmmc_finish_request(host); 719 } 720 } 721 722 static void au1xmmc_reset_controller(struct au1xmmc_host *host) 723 { 724 /* Apply the clock */ 725 __raw_writel(SD_ENABLE_CE, HOST_ENABLE(host)); 726 wmb(); /* drain writebuffer */ 727 mdelay(1); 728 729 __raw_writel(SD_ENABLE_R | SD_ENABLE_CE, HOST_ENABLE(host)); 730 wmb(); /* drain writebuffer */ 731 mdelay(5); 732 733 __raw_writel(~0, HOST_STATUS(host)); 734 wmb(); /* drain writebuffer */ 735 736 __raw_writel(0, HOST_BLKSIZE(host)); 737 __raw_writel(0x001fffff, HOST_TIMEOUT(host)); 738 wmb(); /* drain writebuffer */ 739 740 __raw_writel(SD_CONFIG2_EN, HOST_CONFIG2(host)); 741 wmb(); /* drain writebuffer */ 742 743 __raw_writel(SD_CONFIG2_EN | SD_CONFIG2_FF, HOST_CONFIG2(host)); 744 wmb(); /* drain writebuffer */ 745 mdelay(1); 746 747 __raw_writel(SD_CONFIG2_EN, HOST_CONFIG2(host)); 748 wmb(); /* drain writebuffer */ 749 750 /* Configure interrupts */ 751 __raw_writel(AU1XMMC_INTERRUPTS, HOST_CONFIG(host)); 752 wmb(); /* drain writebuffer */ 753 } 754 755 756 static void au1xmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) 757 { 758 struct au1xmmc_host *host = mmc_priv(mmc); 759 u32 config2; 760 761 if (ios->power_mode == MMC_POWER_OFF) 762 au1xmmc_set_power(host, 0); 763 else if (ios->power_mode == MMC_POWER_ON) { 764 au1xmmc_set_power(host, 1); 765 } 766 767 if (ios->clock && ios->clock != host->clock) { 768 au1xmmc_set_clock(host, ios->clock); 769 host->clock = ios->clock; 770 } 771 772 config2 = __raw_readl(HOST_CONFIG2(host)); 773 switch (ios->bus_width) { 774 case MMC_BUS_WIDTH_8: 775 config2 |= SD_CONFIG2_BB; 776 break; 777 case MMC_BUS_WIDTH_4: 778 config2 &= ~SD_CONFIG2_BB; 779 config2 |= SD_CONFIG2_WB; 780 break; 781 case MMC_BUS_WIDTH_1: 782 config2 &= ~(SD_CONFIG2_WB | SD_CONFIG2_BB); 783 break; 784 } 785 __raw_writel(config2, HOST_CONFIG2(host)); 786 wmb(); /* drain writebuffer */ 787 } 788 789 #define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT) 790 #define STATUS_DATA_IN (SD_STATUS_NE) 791 #define STATUS_DATA_OUT (SD_STATUS_TH) 792 793 static irqreturn_t au1xmmc_irq(int irq, void *dev_id) 794 { 795 struct au1xmmc_host *host = dev_id; 796 u32 status; 797 798 status = __raw_readl(HOST_STATUS(host)); 799 800 if (!(status & SD_STATUS_I)) 801 return IRQ_NONE; /* not ours */ 802 803 if (status & SD_STATUS_SI) /* SDIO */ 804 mmc_signal_sdio_irq(host->mmc); 805 806 if (host->mrq && (status & STATUS_TIMEOUT)) { 807 if (status & SD_STATUS_RAT) 808 host->mrq->cmd->error = -ETIMEDOUT; 809 else if (status & SD_STATUS_DT) 810 host->mrq->data->error = -ETIMEDOUT; 811 812 /* In PIO mode, interrupts might still be enabled */ 813 IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH); 814 815 /* IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA | SD_CONFIG_RF); */ 816 tasklet_schedule(&host->finish_task); 817 } 818 #if 0 819 else if (status & SD_STATUS_DD) { 820 /* Sometimes we get a DD before a NE in PIO mode */ 821 if (!(host->flags & HOST_F_DMA) && (status & SD_STATUS_NE)) 822 au1xmmc_receive_pio(host); 823 else { 824 au1xmmc_data_complete(host, status); 825 /* tasklet_schedule(&host->data_task); */ 826 } 827 } 828 #endif 829 else if (status & SD_STATUS_CR) { 830 if (host->status == HOST_S_CMD) 831 au1xmmc_cmd_complete(host, status); 832 833 } else if (!(host->flags & HOST_F_DMA)) { 834 if ((host->flags & HOST_F_XMIT) && (status & STATUS_DATA_OUT)) 835 au1xmmc_send_pio(host); 836 else if ((host->flags & HOST_F_RECV) && (status & STATUS_DATA_IN)) 837 au1xmmc_receive_pio(host); 838 839 } else if (status & 0x203F3C70) { 840 DBG("Unhandled status %8.8x\n", host->pdev->id, 841 status); 842 } 843 844 __raw_writel(status, HOST_STATUS(host)); 845 wmb(); /* drain writebuffer */ 846 847 return IRQ_HANDLED; 848 } 849 850 /* 8bit memory DMA device */ 851 static dbdev_tab_t au1xmmc_mem_dbdev = { 852 .dev_id = DSCR_CMD0_ALWAYS, 853 .dev_flags = DEV_FLAGS_ANYUSE, 854 .dev_tsize = 0, 855 .dev_devwidth = 8, 856 .dev_physaddr = 0x00000000, 857 .dev_intlevel = 0, 858 .dev_intpolarity = 0, 859 }; 860 static int memid; 861 862 static void au1xmmc_dbdma_callback(int irq, void *dev_id) 863 { 864 struct au1xmmc_host *host = (struct au1xmmc_host *)dev_id; 865 866 /* Avoid spurious interrupts */ 867 if (!host->mrq) 868 return; 869 870 if (host->flags & HOST_F_STOP) 871 SEND_STOP(host); 872 873 tasklet_schedule(&host->data_task); 874 } 875 876 static int au1xmmc_dbdma_init(struct au1xmmc_host *host) 877 { 878 struct resource *res; 879 int txid, rxid; 880 881 res = platform_get_resource(host->pdev, IORESOURCE_DMA, 0); 882 if (!res) 883 return -ENODEV; 884 txid = res->start; 885 886 res = platform_get_resource(host->pdev, IORESOURCE_DMA, 1); 887 if (!res) 888 return -ENODEV; 889 rxid = res->start; 890 891 if (!memid) 892 return -ENODEV; 893 894 host->tx_chan = au1xxx_dbdma_chan_alloc(memid, txid, 895 au1xmmc_dbdma_callback, (void *)host); 896 if (!host->tx_chan) { 897 dev_err(&host->pdev->dev, "cannot allocate TX DMA\n"); 898 return -ENODEV; 899 } 900 901 host->rx_chan = au1xxx_dbdma_chan_alloc(rxid, memid, 902 au1xmmc_dbdma_callback, (void *)host); 903 if (!host->rx_chan) { 904 dev_err(&host->pdev->dev, "cannot allocate RX DMA\n"); 905 au1xxx_dbdma_chan_free(host->tx_chan); 906 return -ENODEV; 907 } 908 909 au1xxx_dbdma_set_devwidth(host->tx_chan, 8); 910 au1xxx_dbdma_set_devwidth(host->rx_chan, 8); 911 912 au1xxx_dbdma_ring_alloc(host->tx_chan, AU1XMMC_DESCRIPTOR_COUNT); 913 au1xxx_dbdma_ring_alloc(host->rx_chan, AU1XMMC_DESCRIPTOR_COUNT); 914 915 /* DBDMA is good to go */ 916 host->flags |= HOST_F_DMA | HOST_F_DBDMA; 917 918 return 0; 919 } 920 921 static void au1xmmc_dbdma_shutdown(struct au1xmmc_host *host) 922 { 923 if (host->flags & HOST_F_DMA) { 924 host->flags &= ~HOST_F_DMA; 925 au1xxx_dbdma_chan_free(host->tx_chan); 926 au1xxx_dbdma_chan_free(host->rx_chan); 927 } 928 } 929 930 static void au1xmmc_enable_sdio_irq(struct mmc_host *mmc, int en) 931 { 932 struct au1xmmc_host *host = mmc_priv(mmc); 933 934 if (en) 935 IRQ_ON(host, SD_CONFIG_SI); 936 else 937 IRQ_OFF(host, SD_CONFIG_SI); 938 } 939 940 static const struct mmc_host_ops au1xmmc_ops = { 941 .request = au1xmmc_request, 942 .set_ios = au1xmmc_set_ios, 943 .get_ro = au1xmmc_card_readonly, 944 .get_cd = au1xmmc_card_inserted, 945 .enable_sdio_irq = au1xmmc_enable_sdio_irq, 946 }; 947 948 static int au1xmmc_probe(struct platform_device *pdev) 949 { 950 struct mmc_host *mmc; 951 struct au1xmmc_host *host; 952 struct resource *r; 953 int ret, iflag; 954 955 mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev); 956 if (!mmc) { 957 dev_err(&pdev->dev, "no memory for mmc_host\n"); 958 ret = -ENOMEM; 959 goto out0; 960 } 961 962 host = mmc_priv(mmc); 963 host->mmc = mmc; 964 host->platdata = pdev->dev.platform_data; 965 host->pdev = pdev; 966 967 ret = -ENODEV; 968 r = platform_get_resource(pdev, IORESOURCE_MEM, 0); 969 if (!r) { 970 dev_err(&pdev->dev, "no mmio defined\n"); 971 goto out1; 972 } 973 974 host->ioarea = request_mem_region(r->start, resource_size(r), 975 pdev->name); 976 if (!host->ioarea) { 977 dev_err(&pdev->dev, "mmio already in use\n"); 978 goto out1; 979 } 980 981 host->iobase = ioremap(r->start, 0x3c); 982 if (!host->iobase) { 983 dev_err(&pdev->dev, "cannot remap mmio\n"); 984 goto out2; 985 } 986 987 host->irq = platform_get_irq(pdev, 0); 988 if (host->irq < 0) 989 goto out3; 990 991 mmc->ops = &au1xmmc_ops; 992 993 mmc->f_min = 450000; 994 mmc->f_max = 24000000; 995 996 mmc->max_blk_size = 2048; 997 mmc->max_blk_count = 512; 998 999 mmc->ocr_avail = AU1XMMC_OCR; 1000 mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ; 1001 mmc->max_segs = AU1XMMC_DESCRIPTOR_COUNT; 1002 1003 iflag = IRQF_SHARED; /* Au1100/Au1200: one int for both ctrls */ 1004 1005 switch (alchemy_get_cputype()) { 1006 case ALCHEMY_CPU_AU1100: 1007 mmc->max_seg_size = AU1100_MMC_DESCRIPTOR_SIZE; 1008 break; 1009 case ALCHEMY_CPU_AU1200: 1010 mmc->max_seg_size = AU1200_MMC_DESCRIPTOR_SIZE; 1011 break; 1012 case ALCHEMY_CPU_AU1300: 1013 iflag = 0; /* nothing is shared */ 1014 mmc->max_seg_size = AU1200_MMC_DESCRIPTOR_SIZE; 1015 mmc->f_max = 52000000; 1016 if (host->ioarea->start == AU1100_SD0_PHYS_ADDR) 1017 mmc->caps |= MMC_CAP_8_BIT_DATA; 1018 break; 1019 } 1020 1021 ret = request_irq(host->irq, au1xmmc_irq, iflag, DRIVER_NAME, host); 1022 if (ret) { 1023 dev_err(&pdev->dev, "cannot grab IRQ\n"); 1024 goto out3; 1025 } 1026 1027 host->clk = clk_get(&pdev->dev, ALCHEMY_PERIPH_CLK); 1028 if (IS_ERR(host->clk)) { 1029 dev_err(&pdev->dev, "cannot find clock\n"); 1030 ret = PTR_ERR(host->clk); 1031 goto out_irq; 1032 } 1033 1034 ret = clk_prepare_enable(host->clk); 1035 if (ret) { 1036 dev_err(&pdev->dev, "cannot enable clock\n"); 1037 goto out_clk; 1038 } 1039 1040 host->status = HOST_S_IDLE; 1041 1042 /* board-specific carddetect setup, if any */ 1043 if (host->platdata && host->platdata->cd_setup) { 1044 ret = host->platdata->cd_setup(mmc, 1); 1045 if (ret) { 1046 dev_warn(&pdev->dev, "board CD setup failed\n"); 1047 mmc->caps |= MMC_CAP_NEEDS_POLL; 1048 } 1049 } else 1050 mmc->caps |= MMC_CAP_NEEDS_POLL; 1051 1052 /* platform may not be able to use all advertised caps */ 1053 if (host->platdata) 1054 mmc->caps &= ~(host->platdata->mask_host_caps); 1055 1056 tasklet_init(&host->data_task, au1xmmc_tasklet_data, 1057 (unsigned long)host); 1058 1059 tasklet_init(&host->finish_task, au1xmmc_tasklet_finish, 1060 (unsigned long)host); 1061 1062 if (has_dbdma()) { 1063 ret = au1xmmc_dbdma_init(host); 1064 if (ret) 1065 pr_info(DRIVER_NAME ": DBDMA init failed; using PIO\n"); 1066 } 1067 1068 #ifdef CONFIG_LEDS_CLASS 1069 if (host->platdata && host->platdata->led) { 1070 struct led_classdev *led = host->platdata->led; 1071 led->name = mmc_hostname(mmc); 1072 led->brightness = LED_OFF; 1073 led->default_trigger = mmc_hostname(mmc); 1074 ret = led_classdev_register(mmc_dev(mmc), led); 1075 if (ret) 1076 goto out5; 1077 } 1078 #endif 1079 1080 au1xmmc_reset_controller(host); 1081 1082 ret = mmc_add_host(mmc); 1083 if (ret) { 1084 dev_err(&pdev->dev, "cannot add mmc host\n"); 1085 goto out6; 1086 } 1087 1088 platform_set_drvdata(pdev, host); 1089 1090 pr_info(DRIVER_NAME ": MMC Controller %d set up at %p" 1091 " (mode=%s)\n", pdev->id, host->iobase, 1092 host->flags & HOST_F_DMA ? "dma" : "pio"); 1093 1094 return 0; /* all ok */ 1095 1096 out6: 1097 #ifdef CONFIG_LEDS_CLASS 1098 if (host->platdata && host->platdata->led) 1099 led_classdev_unregister(host->platdata->led); 1100 out5: 1101 #endif 1102 __raw_writel(0, HOST_ENABLE(host)); 1103 __raw_writel(0, HOST_CONFIG(host)); 1104 __raw_writel(0, HOST_CONFIG2(host)); 1105 wmb(); /* drain writebuffer */ 1106 1107 if (host->flags & HOST_F_DBDMA) 1108 au1xmmc_dbdma_shutdown(host); 1109 1110 tasklet_kill(&host->data_task); 1111 tasklet_kill(&host->finish_task); 1112 1113 if (host->platdata && host->platdata->cd_setup && 1114 !(mmc->caps & MMC_CAP_NEEDS_POLL)) 1115 host->platdata->cd_setup(mmc, 0); 1116 out_clk: 1117 clk_disable_unprepare(host->clk); 1118 clk_put(host->clk); 1119 out_irq: 1120 free_irq(host->irq, host); 1121 out3: 1122 iounmap((void *)host->iobase); 1123 out2: 1124 release_resource(host->ioarea); 1125 kfree(host->ioarea); 1126 out1: 1127 mmc_free_host(mmc); 1128 out0: 1129 return ret; 1130 } 1131 1132 static int au1xmmc_remove(struct platform_device *pdev) 1133 { 1134 struct au1xmmc_host *host = platform_get_drvdata(pdev); 1135 1136 if (host) { 1137 mmc_remove_host(host->mmc); 1138 1139 #ifdef CONFIG_LEDS_CLASS 1140 if (host->platdata && host->platdata->led) 1141 led_classdev_unregister(host->platdata->led); 1142 #endif 1143 1144 if (host->platdata && host->platdata->cd_setup && 1145 !(host->mmc->caps & MMC_CAP_NEEDS_POLL)) 1146 host->platdata->cd_setup(host->mmc, 0); 1147 1148 __raw_writel(0, HOST_ENABLE(host)); 1149 __raw_writel(0, HOST_CONFIG(host)); 1150 __raw_writel(0, HOST_CONFIG2(host)); 1151 wmb(); /* drain writebuffer */ 1152 1153 tasklet_kill(&host->data_task); 1154 tasklet_kill(&host->finish_task); 1155 1156 if (host->flags & HOST_F_DBDMA) 1157 au1xmmc_dbdma_shutdown(host); 1158 1159 au1xmmc_set_power(host, 0); 1160 1161 clk_disable_unprepare(host->clk); 1162 clk_put(host->clk); 1163 1164 free_irq(host->irq, host); 1165 iounmap((void *)host->iobase); 1166 release_resource(host->ioarea); 1167 kfree(host->ioarea); 1168 1169 mmc_free_host(host->mmc); 1170 } 1171 return 0; 1172 } 1173 1174 #ifdef CONFIG_PM 1175 static int au1xmmc_suspend(struct platform_device *pdev, pm_message_t state) 1176 { 1177 struct au1xmmc_host *host = platform_get_drvdata(pdev); 1178 1179 __raw_writel(0, HOST_CONFIG2(host)); 1180 __raw_writel(0, HOST_CONFIG(host)); 1181 __raw_writel(0xffffffff, HOST_STATUS(host)); 1182 __raw_writel(0, HOST_ENABLE(host)); 1183 wmb(); /* drain writebuffer */ 1184 1185 return 0; 1186 } 1187 1188 static int au1xmmc_resume(struct platform_device *pdev) 1189 { 1190 struct au1xmmc_host *host = platform_get_drvdata(pdev); 1191 1192 au1xmmc_reset_controller(host); 1193 1194 return 0; 1195 } 1196 #else 1197 #define au1xmmc_suspend NULL 1198 #define au1xmmc_resume NULL 1199 #endif 1200 1201 static struct platform_driver au1xmmc_driver = { 1202 .probe = au1xmmc_probe, 1203 .remove = au1xmmc_remove, 1204 .suspend = au1xmmc_suspend, 1205 .resume = au1xmmc_resume, 1206 .driver = { 1207 .name = DRIVER_NAME, 1208 }, 1209 }; 1210 1211 static int __init au1xmmc_init(void) 1212 { 1213 if (has_dbdma()) { 1214 /* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride 1215 * of 8 bits. And since devices are shared, we need to create 1216 * our own to avoid freaking out other devices. 1217 */ 1218 memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev); 1219 if (!memid) 1220 pr_err("au1xmmc: cannot add memory dbdma\n"); 1221 } 1222 return platform_driver_register(&au1xmmc_driver); 1223 } 1224 1225 static void __exit au1xmmc_exit(void) 1226 { 1227 if (has_dbdma() && memid) 1228 au1xxx_ddma_del_device(memid); 1229 1230 platform_driver_unregister(&au1xmmc_driver); 1231 } 1232 1233 module_init(au1xmmc_init); 1234 module_exit(au1xmmc_exit); 1235 1236 MODULE_AUTHOR("Advanced Micro Devices, Inc"); 1237 MODULE_DESCRIPTION("MMC/SD driver for the Alchemy Au1XXX"); 1238 MODULE_LICENSE("GPL"); 1239 MODULE_ALIAS("platform:au1xxx-mmc"); 1240