1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * linux/drivers/mmc/core/core.c 4 * 5 * Copyright (C) 2003-2004 Russell King, All Rights Reserved. 6 * SD support Copyright (C) 2004 Ian Molton, All Rights Reserved. 7 * Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved. 8 * MMCv4 support Copyright (C) 2006 Philip Langdale, All Rights Reserved. 9 */ 10 #include <linux/module.h> 11 #include <linux/init.h> 12 #include <linux/interrupt.h> 13 #include <linux/completion.h> 14 #include <linux/device.h> 15 #include <linux/delay.h> 16 #include <linux/pagemap.h> 17 #include <linux/err.h> 18 #include <linux/leds.h> 19 #include <linux/scatterlist.h> 20 #include <linux/log2.h> 21 #include <linux/pm_runtime.h> 22 #include <linux/pm_wakeup.h> 23 #include <linux/suspend.h> 24 #include <linux/fault-inject.h> 25 #include <linux/random.h> 26 #include <linux/slab.h> 27 #include <linux/of.h> 28 29 #include <linux/mmc/card.h> 30 #include <linux/mmc/host.h> 31 #include <linux/mmc/mmc.h> 32 #include <linux/mmc/sd.h> 33 #include <linux/mmc/slot-gpio.h> 34 35 #define CREATE_TRACE_POINTS 36 #include <trace/events/mmc.h> 37 38 #include "core.h" 39 #include "card.h" 40 #include "crypto.h" 41 #include "bus.h" 42 #include "host.h" 43 #include "sdio_bus.h" 44 #include "pwrseq.h" 45 46 #include "mmc_ops.h" 47 #include "sd_ops.h" 48 #include "sdio_ops.h" 49 50 /* The max erase timeout, used when host->max_busy_timeout isn't specified */ 51 #define MMC_ERASE_TIMEOUT_MS (60 * 1000) /* 60 s */ 52 #define SD_DISCARD_TIMEOUT_MS (250) 53 54 static const unsigned freqs[] = { 400000, 300000, 200000, 100000 }; 55 56 /* 57 * Enabling software CRCs on the data blocks can be a significant (30%) 58 * performance cost, and for other reasons may not always be desired. 59 * So we allow it it to be disabled. 60 */ 61 bool use_spi_crc = 1; 62 module_param(use_spi_crc, bool, 0); 63 64 static int mmc_schedule_delayed_work(struct delayed_work *work, 65 unsigned long delay) 66 { 67 /* 68 * We use the system_freezable_wq, because of two reasons. 69 * First, it allows several works (not the same work item) to be 70 * executed simultaneously. Second, the queue becomes frozen when 71 * userspace becomes frozen during system PM. 72 */ 73 return queue_delayed_work(system_freezable_wq, work, delay); 74 } 75 76 #ifdef CONFIG_FAIL_MMC_REQUEST 77 78 /* 79 * Internal function. Inject random data errors. 80 * If mmc_data is NULL no errors are injected. 81 */ 82 static void mmc_should_fail_request(struct mmc_host *host, 83 struct mmc_request *mrq) 84 { 85 struct mmc_command *cmd = mrq->cmd; 86 struct mmc_data *data = mrq->data; 87 static const int data_errors[] = { 88 -ETIMEDOUT, 89 -EILSEQ, 90 -EIO, 91 }; 92 93 if (!data) 94 return; 95 96 if ((cmd && cmd->error) || data->error || 97 !should_fail(&host->fail_mmc_request, data->blksz * data->blocks)) 98 return; 99 100 data->error = data_errors[prandom_u32() % ARRAY_SIZE(data_errors)]; 101 data->bytes_xfered = (prandom_u32() % (data->bytes_xfered >> 9)) << 9; 102 } 103 104 #else /* CONFIG_FAIL_MMC_REQUEST */ 105 106 static inline void mmc_should_fail_request(struct mmc_host *host, 107 struct mmc_request *mrq) 108 { 109 } 110 111 #endif /* CONFIG_FAIL_MMC_REQUEST */ 112 113 static inline void mmc_complete_cmd(struct mmc_request *mrq) 114 { 115 if (mrq->cap_cmd_during_tfr && !completion_done(&mrq->cmd_completion)) 116 complete_all(&mrq->cmd_completion); 117 } 118 119 void mmc_command_done(struct mmc_host *host, struct mmc_request *mrq) 120 { 121 if (!mrq->cap_cmd_during_tfr) 122 return; 123 124 mmc_complete_cmd(mrq); 125 126 pr_debug("%s: cmd done, tfr ongoing (CMD%u)\n", 127 mmc_hostname(host), mrq->cmd->opcode); 128 } 129 EXPORT_SYMBOL(mmc_command_done); 130 131 /** 132 * mmc_request_done - finish processing an MMC request 133 * @host: MMC host which completed request 134 * @mrq: MMC request which request 135 * 136 * MMC drivers should call this function when they have completed 137 * their processing of a request. 138 */ 139 void mmc_request_done(struct mmc_host *host, struct mmc_request *mrq) 140 { 141 struct mmc_command *cmd = mrq->cmd; 142 int err = cmd->error; 143 144 /* Flag re-tuning needed on CRC errors */ 145 if (cmd->opcode != MMC_SEND_TUNING_BLOCK && 146 cmd->opcode != MMC_SEND_TUNING_BLOCK_HS200 && 147 !host->retune_crc_disable && 148 (err == -EILSEQ || (mrq->sbc && mrq->sbc->error == -EILSEQ) || 149 (mrq->data && mrq->data->error == -EILSEQ) || 150 (mrq->stop && mrq->stop->error == -EILSEQ))) 151 mmc_retune_needed(host); 152 153 if (err && cmd->retries && mmc_host_is_spi(host)) { 154 if (cmd->resp[0] & R1_SPI_ILLEGAL_COMMAND) 155 cmd->retries = 0; 156 } 157 158 if (host->ongoing_mrq == mrq) 159 host->ongoing_mrq = NULL; 160 161 mmc_complete_cmd(mrq); 162 163 trace_mmc_request_done(host, mrq); 164 165 /* 166 * We list various conditions for the command to be considered 167 * properly done: 168 * 169 * - There was no error, OK fine then 170 * - We are not doing some kind of retry 171 * - The card was removed (...so just complete everything no matter 172 * if there are errors or retries) 173 */ 174 if (!err || !cmd->retries || mmc_card_removed(host->card)) { 175 mmc_should_fail_request(host, mrq); 176 177 if (!host->ongoing_mrq) 178 led_trigger_event(host->led, LED_OFF); 179 180 if (mrq->sbc) { 181 pr_debug("%s: req done <CMD%u>: %d: %08x %08x %08x %08x\n", 182 mmc_hostname(host), mrq->sbc->opcode, 183 mrq->sbc->error, 184 mrq->sbc->resp[0], mrq->sbc->resp[1], 185 mrq->sbc->resp[2], mrq->sbc->resp[3]); 186 } 187 188 pr_debug("%s: req done (CMD%u): %d: %08x %08x %08x %08x\n", 189 mmc_hostname(host), cmd->opcode, err, 190 cmd->resp[0], cmd->resp[1], 191 cmd->resp[2], cmd->resp[3]); 192 193 if (mrq->data) { 194 pr_debug("%s: %d bytes transferred: %d\n", 195 mmc_hostname(host), 196 mrq->data->bytes_xfered, mrq->data->error); 197 } 198 199 if (mrq->stop) { 200 pr_debug("%s: (CMD%u): %d: %08x %08x %08x %08x\n", 201 mmc_hostname(host), mrq->stop->opcode, 202 mrq->stop->error, 203 mrq->stop->resp[0], mrq->stop->resp[1], 204 mrq->stop->resp[2], mrq->stop->resp[3]); 205 } 206 } 207 /* 208 * Request starter must handle retries - see 209 * mmc_wait_for_req_done(). 210 */ 211 if (mrq->done) 212 mrq->done(mrq); 213 } 214 215 EXPORT_SYMBOL(mmc_request_done); 216 217 static void __mmc_start_request(struct mmc_host *host, struct mmc_request *mrq) 218 { 219 int err; 220 221 /* Assumes host controller has been runtime resumed by mmc_claim_host */ 222 err = mmc_retune(host); 223 if (err) { 224 mrq->cmd->error = err; 225 mmc_request_done(host, mrq); 226 return; 227 } 228 229 /* 230 * For sdio rw commands we must wait for card busy otherwise some 231 * sdio devices won't work properly. 232 * And bypass I/O abort, reset and bus suspend operations. 233 */ 234 if (sdio_is_io_busy(mrq->cmd->opcode, mrq->cmd->arg) && 235 host->ops->card_busy) { 236 int tries = 500; /* Wait aprox 500ms at maximum */ 237 238 while (host->ops->card_busy(host) && --tries) 239 mmc_delay(1); 240 241 if (tries == 0) { 242 mrq->cmd->error = -EBUSY; 243 mmc_request_done(host, mrq); 244 return; 245 } 246 } 247 248 if (mrq->cap_cmd_during_tfr) { 249 host->ongoing_mrq = mrq; 250 /* 251 * Retry path could come through here without having waiting on 252 * cmd_completion, so ensure it is reinitialised. 253 */ 254 reinit_completion(&mrq->cmd_completion); 255 } 256 257 trace_mmc_request_start(host, mrq); 258 259 if (host->cqe_on) 260 host->cqe_ops->cqe_off(host); 261 262 host->ops->request(host, mrq); 263 } 264 265 static void mmc_mrq_pr_debug(struct mmc_host *host, struct mmc_request *mrq, 266 bool cqe) 267 { 268 if (mrq->sbc) { 269 pr_debug("<%s: starting CMD%u arg %08x flags %08x>\n", 270 mmc_hostname(host), mrq->sbc->opcode, 271 mrq->sbc->arg, mrq->sbc->flags); 272 } 273 274 if (mrq->cmd) { 275 pr_debug("%s: starting %sCMD%u arg %08x flags %08x\n", 276 mmc_hostname(host), cqe ? "CQE direct " : "", 277 mrq->cmd->opcode, mrq->cmd->arg, mrq->cmd->flags); 278 } else if (cqe) { 279 pr_debug("%s: starting CQE transfer for tag %d blkaddr %u\n", 280 mmc_hostname(host), mrq->tag, mrq->data->blk_addr); 281 } 282 283 if (mrq->data) { 284 pr_debug("%s: blksz %d blocks %d flags %08x " 285 "tsac %d ms nsac %d\n", 286 mmc_hostname(host), mrq->data->blksz, 287 mrq->data->blocks, mrq->data->flags, 288 mrq->data->timeout_ns / 1000000, 289 mrq->data->timeout_clks); 290 } 291 292 if (mrq->stop) { 293 pr_debug("%s: CMD%u arg %08x flags %08x\n", 294 mmc_hostname(host), mrq->stop->opcode, 295 mrq->stop->arg, mrq->stop->flags); 296 } 297 } 298 299 static int mmc_mrq_prep(struct mmc_host *host, struct mmc_request *mrq) 300 { 301 unsigned int i, sz = 0; 302 struct scatterlist *sg; 303 304 if (mrq->cmd) { 305 mrq->cmd->error = 0; 306 mrq->cmd->mrq = mrq; 307 mrq->cmd->data = mrq->data; 308 } 309 if (mrq->sbc) { 310 mrq->sbc->error = 0; 311 mrq->sbc->mrq = mrq; 312 } 313 if (mrq->data) { 314 if (mrq->data->blksz > host->max_blk_size || 315 mrq->data->blocks > host->max_blk_count || 316 mrq->data->blocks * mrq->data->blksz > host->max_req_size) 317 return -EINVAL; 318 319 for_each_sg(mrq->data->sg, sg, mrq->data->sg_len, i) 320 sz += sg->length; 321 if (sz != mrq->data->blocks * mrq->data->blksz) 322 return -EINVAL; 323 324 mrq->data->error = 0; 325 mrq->data->mrq = mrq; 326 if (mrq->stop) { 327 mrq->data->stop = mrq->stop; 328 mrq->stop->error = 0; 329 mrq->stop->mrq = mrq; 330 } 331 } 332 333 return 0; 334 } 335 336 int mmc_start_request(struct mmc_host *host, struct mmc_request *mrq) 337 { 338 int err; 339 340 init_completion(&mrq->cmd_completion); 341 342 mmc_retune_hold(host); 343 344 if (mmc_card_removed(host->card)) 345 return -ENOMEDIUM; 346 347 mmc_mrq_pr_debug(host, mrq, false); 348 349 WARN_ON(!host->claimed); 350 351 err = mmc_mrq_prep(host, mrq); 352 if (err) 353 return err; 354 355 led_trigger_event(host->led, LED_FULL); 356 __mmc_start_request(host, mrq); 357 358 return 0; 359 } 360 EXPORT_SYMBOL(mmc_start_request); 361 362 static void mmc_wait_done(struct mmc_request *mrq) 363 { 364 complete(&mrq->completion); 365 } 366 367 static inline void mmc_wait_ongoing_tfr_cmd(struct mmc_host *host) 368 { 369 struct mmc_request *ongoing_mrq = READ_ONCE(host->ongoing_mrq); 370 371 /* 372 * If there is an ongoing transfer, wait for the command line to become 373 * available. 374 */ 375 if (ongoing_mrq && !completion_done(&ongoing_mrq->cmd_completion)) 376 wait_for_completion(&ongoing_mrq->cmd_completion); 377 } 378 379 static int __mmc_start_req(struct mmc_host *host, struct mmc_request *mrq) 380 { 381 int err; 382 383 mmc_wait_ongoing_tfr_cmd(host); 384 385 init_completion(&mrq->completion); 386 mrq->done = mmc_wait_done; 387 388 err = mmc_start_request(host, mrq); 389 if (err) { 390 mrq->cmd->error = err; 391 mmc_complete_cmd(mrq); 392 complete(&mrq->completion); 393 } 394 395 return err; 396 } 397 398 void mmc_wait_for_req_done(struct mmc_host *host, struct mmc_request *mrq) 399 { 400 struct mmc_command *cmd; 401 402 while (1) { 403 wait_for_completion(&mrq->completion); 404 405 cmd = mrq->cmd; 406 407 if (!cmd->error || !cmd->retries || 408 mmc_card_removed(host->card)) 409 break; 410 411 mmc_retune_recheck(host); 412 413 pr_debug("%s: req failed (CMD%u): %d, retrying...\n", 414 mmc_hostname(host), cmd->opcode, cmd->error); 415 cmd->retries--; 416 cmd->error = 0; 417 __mmc_start_request(host, mrq); 418 } 419 420 mmc_retune_release(host); 421 } 422 EXPORT_SYMBOL(mmc_wait_for_req_done); 423 424 /* 425 * mmc_cqe_start_req - Start a CQE request. 426 * @host: MMC host to start the request 427 * @mrq: request to start 428 * 429 * Start the request, re-tuning if needed and it is possible. Returns an error 430 * code if the request fails to start or -EBUSY if CQE is busy. 431 */ 432 int mmc_cqe_start_req(struct mmc_host *host, struct mmc_request *mrq) 433 { 434 int err; 435 436 /* 437 * CQE cannot process re-tuning commands. Caller must hold retuning 438 * while CQE is in use. Re-tuning can happen here only when CQE has no 439 * active requests i.e. this is the first. Note, re-tuning will call 440 * ->cqe_off(). 441 */ 442 err = mmc_retune(host); 443 if (err) 444 goto out_err; 445 446 mrq->host = host; 447 448 mmc_mrq_pr_debug(host, mrq, true); 449 450 err = mmc_mrq_prep(host, mrq); 451 if (err) 452 goto out_err; 453 454 err = host->cqe_ops->cqe_request(host, mrq); 455 if (err) 456 goto out_err; 457 458 trace_mmc_request_start(host, mrq); 459 460 return 0; 461 462 out_err: 463 if (mrq->cmd) { 464 pr_debug("%s: failed to start CQE direct CMD%u, error %d\n", 465 mmc_hostname(host), mrq->cmd->opcode, err); 466 } else { 467 pr_debug("%s: failed to start CQE transfer for tag %d, error %d\n", 468 mmc_hostname(host), mrq->tag, err); 469 } 470 return err; 471 } 472 EXPORT_SYMBOL(mmc_cqe_start_req); 473 474 /** 475 * mmc_cqe_request_done - CQE has finished processing an MMC request 476 * @host: MMC host which completed request 477 * @mrq: MMC request which completed 478 * 479 * CQE drivers should call this function when they have completed 480 * their processing of a request. 481 */ 482 void mmc_cqe_request_done(struct mmc_host *host, struct mmc_request *mrq) 483 { 484 mmc_should_fail_request(host, mrq); 485 486 /* Flag re-tuning needed on CRC errors */ 487 if ((mrq->cmd && mrq->cmd->error == -EILSEQ) || 488 (mrq->data && mrq->data->error == -EILSEQ)) 489 mmc_retune_needed(host); 490 491 trace_mmc_request_done(host, mrq); 492 493 if (mrq->cmd) { 494 pr_debug("%s: CQE req done (direct CMD%u): %d\n", 495 mmc_hostname(host), mrq->cmd->opcode, mrq->cmd->error); 496 } else { 497 pr_debug("%s: CQE transfer done tag %d\n", 498 mmc_hostname(host), mrq->tag); 499 } 500 501 if (mrq->data) { 502 pr_debug("%s: %d bytes transferred: %d\n", 503 mmc_hostname(host), 504 mrq->data->bytes_xfered, mrq->data->error); 505 } 506 507 mrq->done(mrq); 508 } 509 EXPORT_SYMBOL(mmc_cqe_request_done); 510 511 /** 512 * mmc_cqe_post_req - CQE post process of a completed MMC request 513 * @host: MMC host 514 * @mrq: MMC request to be processed 515 */ 516 void mmc_cqe_post_req(struct mmc_host *host, struct mmc_request *mrq) 517 { 518 if (host->cqe_ops->cqe_post_req) 519 host->cqe_ops->cqe_post_req(host, mrq); 520 } 521 EXPORT_SYMBOL(mmc_cqe_post_req); 522 523 /* Arbitrary 1 second timeout */ 524 #define MMC_CQE_RECOVERY_TIMEOUT 1000 525 526 /* 527 * mmc_cqe_recovery - Recover from CQE errors. 528 * @host: MMC host to recover 529 * 530 * Recovery consists of stopping CQE, stopping eMMC, discarding the queue in 531 * in eMMC, and discarding the queue in CQE. CQE must call 532 * mmc_cqe_request_done() on all requests. An error is returned if the eMMC 533 * fails to discard its queue. 534 */ 535 int mmc_cqe_recovery(struct mmc_host *host) 536 { 537 struct mmc_command cmd; 538 int err; 539 540 mmc_retune_hold_now(host); 541 542 /* 543 * Recovery is expected seldom, if at all, but it reduces performance, 544 * so make sure it is not completely silent. 545 */ 546 pr_warn("%s: running CQE recovery\n", mmc_hostname(host)); 547 548 host->cqe_ops->cqe_recovery_start(host); 549 550 memset(&cmd, 0, sizeof(cmd)); 551 cmd.opcode = MMC_STOP_TRANSMISSION; 552 cmd.flags = MMC_RSP_R1B | MMC_CMD_AC; 553 cmd.flags &= ~MMC_RSP_CRC; /* Ignore CRC */ 554 cmd.busy_timeout = MMC_CQE_RECOVERY_TIMEOUT; 555 mmc_wait_for_cmd(host, &cmd, 0); 556 557 memset(&cmd, 0, sizeof(cmd)); 558 cmd.opcode = MMC_CMDQ_TASK_MGMT; 559 cmd.arg = 1; /* Discard entire queue */ 560 cmd.flags = MMC_RSP_R1B | MMC_CMD_AC; 561 cmd.flags &= ~MMC_RSP_CRC; /* Ignore CRC */ 562 cmd.busy_timeout = MMC_CQE_RECOVERY_TIMEOUT; 563 err = mmc_wait_for_cmd(host, &cmd, 0); 564 565 host->cqe_ops->cqe_recovery_finish(host); 566 567 mmc_retune_release(host); 568 569 return err; 570 } 571 EXPORT_SYMBOL(mmc_cqe_recovery); 572 573 /** 574 * mmc_is_req_done - Determine if a 'cap_cmd_during_tfr' request is done 575 * @host: MMC host 576 * @mrq: MMC request 577 * 578 * mmc_is_req_done() is used with requests that have 579 * mrq->cap_cmd_during_tfr = true. mmc_is_req_done() must be called after 580 * starting a request and before waiting for it to complete. That is, 581 * either in between calls to mmc_start_req(), or after mmc_wait_for_req() 582 * and before mmc_wait_for_req_done(). If it is called at other times the 583 * result is not meaningful. 584 */ 585 bool mmc_is_req_done(struct mmc_host *host, struct mmc_request *mrq) 586 { 587 return completion_done(&mrq->completion); 588 } 589 EXPORT_SYMBOL(mmc_is_req_done); 590 591 /** 592 * mmc_wait_for_req - start a request and wait for completion 593 * @host: MMC host to start command 594 * @mrq: MMC request to start 595 * 596 * Start a new MMC custom command request for a host, and wait 597 * for the command to complete. In the case of 'cap_cmd_during_tfr' 598 * requests, the transfer is ongoing and the caller can issue further 599 * commands that do not use the data lines, and then wait by calling 600 * mmc_wait_for_req_done(). 601 * Does not attempt to parse the response. 602 */ 603 void mmc_wait_for_req(struct mmc_host *host, struct mmc_request *mrq) 604 { 605 __mmc_start_req(host, mrq); 606 607 if (!mrq->cap_cmd_during_tfr) 608 mmc_wait_for_req_done(host, mrq); 609 } 610 EXPORT_SYMBOL(mmc_wait_for_req); 611 612 /** 613 * mmc_wait_for_cmd - start a command and wait for completion 614 * @host: MMC host to start command 615 * @cmd: MMC command to start 616 * @retries: maximum number of retries 617 * 618 * Start a new MMC command for a host, and wait for the command 619 * to complete. Return any error that occurred while the command 620 * was executing. Do not attempt to parse the response. 621 */ 622 int mmc_wait_for_cmd(struct mmc_host *host, struct mmc_command *cmd, int retries) 623 { 624 struct mmc_request mrq = {}; 625 626 WARN_ON(!host->claimed); 627 628 memset(cmd->resp, 0, sizeof(cmd->resp)); 629 cmd->retries = retries; 630 631 mrq.cmd = cmd; 632 cmd->data = NULL; 633 634 mmc_wait_for_req(host, &mrq); 635 636 return cmd->error; 637 } 638 639 EXPORT_SYMBOL(mmc_wait_for_cmd); 640 641 /** 642 * mmc_set_data_timeout - set the timeout for a data command 643 * @data: data phase for command 644 * @card: the MMC card associated with the data transfer 645 * 646 * Computes the data timeout parameters according to the 647 * correct algorithm given the card type. 648 */ 649 void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card) 650 { 651 unsigned int mult; 652 653 /* 654 * SDIO cards only define an upper 1 s limit on access. 655 */ 656 if (mmc_card_sdio(card)) { 657 data->timeout_ns = 1000000000; 658 data->timeout_clks = 0; 659 return; 660 } 661 662 /* 663 * SD cards use a 100 multiplier rather than 10 664 */ 665 mult = mmc_card_sd(card) ? 100 : 10; 666 667 /* 668 * Scale up the multiplier (and therefore the timeout) by 669 * the r2w factor for writes. 670 */ 671 if (data->flags & MMC_DATA_WRITE) 672 mult <<= card->csd.r2w_factor; 673 674 data->timeout_ns = card->csd.taac_ns * mult; 675 data->timeout_clks = card->csd.taac_clks * mult; 676 677 /* 678 * SD cards also have an upper limit on the timeout. 679 */ 680 if (mmc_card_sd(card)) { 681 unsigned int timeout_us, limit_us; 682 683 timeout_us = data->timeout_ns / 1000; 684 if (card->host->ios.clock) 685 timeout_us += data->timeout_clks * 1000 / 686 (card->host->ios.clock / 1000); 687 688 if (data->flags & MMC_DATA_WRITE) 689 /* 690 * The MMC spec "It is strongly recommended 691 * for hosts to implement more than 500ms 692 * timeout value even if the card indicates 693 * the 250ms maximum busy length." Even the 694 * previous value of 300ms is known to be 695 * insufficient for some cards. 696 */ 697 limit_us = 3000000; 698 else 699 limit_us = 100000; 700 701 /* 702 * SDHC cards always use these fixed values. 703 */ 704 if (timeout_us > limit_us) { 705 data->timeout_ns = limit_us * 1000; 706 data->timeout_clks = 0; 707 } 708 709 /* assign limit value if invalid */ 710 if (timeout_us == 0) 711 data->timeout_ns = limit_us * 1000; 712 } 713 714 /* 715 * Some cards require longer data read timeout than indicated in CSD. 716 * Address this by setting the read timeout to a "reasonably high" 717 * value. For the cards tested, 600ms has proven enough. If necessary, 718 * this value can be increased if other problematic cards require this. 719 */ 720 if (mmc_card_long_read_time(card) && data->flags & MMC_DATA_READ) { 721 data->timeout_ns = 600000000; 722 data->timeout_clks = 0; 723 } 724 725 /* 726 * Some cards need very high timeouts if driven in SPI mode. 727 * The worst observed timeout was 900ms after writing a 728 * continuous stream of data until the internal logic 729 * overflowed. 730 */ 731 if (mmc_host_is_spi(card->host)) { 732 if (data->flags & MMC_DATA_WRITE) { 733 if (data->timeout_ns < 1000000000) 734 data->timeout_ns = 1000000000; /* 1s */ 735 } else { 736 if (data->timeout_ns < 100000000) 737 data->timeout_ns = 100000000; /* 100ms */ 738 } 739 } 740 } 741 EXPORT_SYMBOL(mmc_set_data_timeout); 742 743 /* 744 * Allow claiming an already claimed host if the context is the same or there is 745 * no context but the task is the same. 746 */ 747 static inline bool mmc_ctx_matches(struct mmc_host *host, struct mmc_ctx *ctx, 748 struct task_struct *task) 749 { 750 return host->claimer == ctx || 751 (!ctx && task && host->claimer->task == task); 752 } 753 754 static inline void mmc_ctx_set_claimer(struct mmc_host *host, 755 struct mmc_ctx *ctx, 756 struct task_struct *task) 757 { 758 if (!host->claimer) { 759 if (ctx) 760 host->claimer = ctx; 761 else 762 host->claimer = &host->default_ctx; 763 } 764 if (task) 765 host->claimer->task = task; 766 } 767 768 /** 769 * __mmc_claim_host - exclusively claim a host 770 * @host: mmc host to claim 771 * @ctx: context that claims the host or NULL in which case the default 772 * context will be used 773 * @abort: whether or not the operation should be aborted 774 * 775 * Claim a host for a set of operations. If @abort is non null and 776 * dereference a non-zero value then this will return prematurely with 777 * that non-zero value without acquiring the lock. Returns zero 778 * with the lock held otherwise. 779 */ 780 int __mmc_claim_host(struct mmc_host *host, struct mmc_ctx *ctx, 781 atomic_t *abort) 782 { 783 struct task_struct *task = ctx ? NULL : current; 784 DECLARE_WAITQUEUE(wait, current); 785 unsigned long flags; 786 int stop; 787 bool pm = false; 788 789 might_sleep(); 790 791 add_wait_queue(&host->wq, &wait); 792 spin_lock_irqsave(&host->lock, flags); 793 while (1) { 794 set_current_state(TASK_UNINTERRUPTIBLE); 795 stop = abort ? atomic_read(abort) : 0; 796 if (stop || !host->claimed || mmc_ctx_matches(host, ctx, task)) 797 break; 798 spin_unlock_irqrestore(&host->lock, flags); 799 schedule(); 800 spin_lock_irqsave(&host->lock, flags); 801 } 802 set_current_state(TASK_RUNNING); 803 if (!stop) { 804 host->claimed = 1; 805 mmc_ctx_set_claimer(host, ctx, task); 806 host->claim_cnt += 1; 807 if (host->claim_cnt == 1) 808 pm = true; 809 } else 810 wake_up(&host->wq); 811 spin_unlock_irqrestore(&host->lock, flags); 812 remove_wait_queue(&host->wq, &wait); 813 814 if (pm) 815 pm_runtime_get_sync(mmc_dev(host)); 816 817 return stop; 818 } 819 EXPORT_SYMBOL(__mmc_claim_host); 820 821 /** 822 * mmc_release_host - release a host 823 * @host: mmc host to release 824 * 825 * Release a MMC host, allowing others to claim the host 826 * for their operations. 827 */ 828 void mmc_release_host(struct mmc_host *host) 829 { 830 unsigned long flags; 831 832 WARN_ON(!host->claimed); 833 834 spin_lock_irqsave(&host->lock, flags); 835 if (--host->claim_cnt) { 836 /* Release for nested claim */ 837 spin_unlock_irqrestore(&host->lock, flags); 838 } else { 839 host->claimed = 0; 840 host->claimer->task = NULL; 841 host->claimer = NULL; 842 spin_unlock_irqrestore(&host->lock, flags); 843 wake_up(&host->wq); 844 pm_runtime_mark_last_busy(mmc_dev(host)); 845 if (host->caps & MMC_CAP_SYNC_RUNTIME_PM) 846 pm_runtime_put_sync_suspend(mmc_dev(host)); 847 else 848 pm_runtime_put_autosuspend(mmc_dev(host)); 849 } 850 } 851 EXPORT_SYMBOL(mmc_release_host); 852 853 /* 854 * This is a helper function, which fetches a runtime pm reference for the 855 * card device and also claims the host. 856 */ 857 void mmc_get_card(struct mmc_card *card, struct mmc_ctx *ctx) 858 { 859 pm_runtime_get_sync(&card->dev); 860 __mmc_claim_host(card->host, ctx, NULL); 861 } 862 EXPORT_SYMBOL(mmc_get_card); 863 864 /* 865 * This is a helper function, which releases the host and drops the runtime 866 * pm reference for the card device. 867 */ 868 void mmc_put_card(struct mmc_card *card, struct mmc_ctx *ctx) 869 { 870 struct mmc_host *host = card->host; 871 872 WARN_ON(ctx && host->claimer != ctx); 873 874 mmc_release_host(host); 875 pm_runtime_mark_last_busy(&card->dev); 876 pm_runtime_put_autosuspend(&card->dev); 877 } 878 EXPORT_SYMBOL(mmc_put_card); 879 880 /* 881 * Internal function that does the actual ios call to the host driver, 882 * optionally printing some debug output. 883 */ 884 static inline void mmc_set_ios(struct mmc_host *host) 885 { 886 struct mmc_ios *ios = &host->ios; 887 888 pr_debug("%s: clock %uHz busmode %u powermode %u cs %u Vdd %u " 889 "width %u timing %u\n", 890 mmc_hostname(host), ios->clock, ios->bus_mode, 891 ios->power_mode, ios->chip_select, ios->vdd, 892 1 << ios->bus_width, ios->timing); 893 894 host->ops->set_ios(host, ios); 895 } 896 897 /* 898 * Control chip select pin on a host. 899 */ 900 void mmc_set_chip_select(struct mmc_host *host, int mode) 901 { 902 host->ios.chip_select = mode; 903 mmc_set_ios(host); 904 } 905 906 /* 907 * Sets the host clock to the highest possible frequency that 908 * is below "hz". 909 */ 910 void mmc_set_clock(struct mmc_host *host, unsigned int hz) 911 { 912 WARN_ON(hz && hz < host->f_min); 913 914 if (hz > host->f_max) 915 hz = host->f_max; 916 917 host->ios.clock = hz; 918 mmc_set_ios(host); 919 } 920 921 int mmc_execute_tuning(struct mmc_card *card) 922 { 923 struct mmc_host *host = card->host; 924 u32 opcode; 925 int err; 926 927 if (!host->ops->execute_tuning) 928 return 0; 929 930 if (host->cqe_on) 931 host->cqe_ops->cqe_off(host); 932 933 if (mmc_card_mmc(card)) 934 opcode = MMC_SEND_TUNING_BLOCK_HS200; 935 else 936 opcode = MMC_SEND_TUNING_BLOCK; 937 938 err = host->ops->execute_tuning(host, opcode); 939 940 if (err) 941 pr_err("%s: tuning execution failed: %d\n", 942 mmc_hostname(host), err); 943 else 944 mmc_retune_enable(host); 945 946 return err; 947 } 948 949 /* 950 * Change the bus mode (open drain/push-pull) of a host. 951 */ 952 void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode) 953 { 954 host->ios.bus_mode = mode; 955 mmc_set_ios(host); 956 } 957 958 /* 959 * Change data bus width of a host. 960 */ 961 void mmc_set_bus_width(struct mmc_host *host, unsigned int width) 962 { 963 host->ios.bus_width = width; 964 mmc_set_ios(host); 965 } 966 967 /* 968 * Set initial state after a power cycle or a hw_reset. 969 */ 970 void mmc_set_initial_state(struct mmc_host *host) 971 { 972 if (host->cqe_on) 973 host->cqe_ops->cqe_off(host); 974 975 mmc_retune_disable(host); 976 977 if (mmc_host_is_spi(host)) 978 host->ios.chip_select = MMC_CS_HIGH; 979 else 980 host->ios.chip_select = MMC_CS_DONTCARE; 981 host->ios.bus_mode = MMC_BUSMODE_PUSHPULL; 982 host->ios.bus_width = MMC_BUS_WIDTH_1; 983 host->ios.timing = MMC_TIMING_LEGACY; 984 host->ios.drv_type = 0; 985 host->ios.enhanced_strobe = false; 986 987 /* 988 * Make sure we are in non-enhanced strobe mode before we 989 * actually enable it in ext_csd. 990 */ 991 if ((host->caps2 & MMC_CAP2_HS400_ES) && 992 host->ops->hs400_enhanced_strobe) 993 host->ops->hs400_enhanced_strobe(host, &host->ios); 994 995 mmc_set_ios(host); 996 997 mmc_crypto_set_initial_state(host); 998 } 999 1000 /** 1001 * mmc_vdd_to_ocrbitnum - Convert a voltage to the OCR bit number 1002 * @vdd: voltage (mV) 1003 * @low_bits: prefer low bits in boundary cases 1004 * 1005 * This function returns the OCR bit number according to the provided @vdd 1006 * value. If conversion is not possible a negative errno value returned. 1007 * 1008 * Depending on the @low_bits flag the function prefers low or high OCR bits 1009 * on boundary voltages. For example, 1010 * with @low_bits = true, 3300 mV translates to ilog2(MMC_VDD_32_33); 1011 * with @low_bits = false, 3300 mV translates to ilog2(MMC_VDD_33_34); 1012 * 1013 * Any value in the [1951:1999] range translates to the ilog2(MMC_VDD_20_21). 1014 */ 1015 static int mmc_vdd_to_ocrbitnum(int vdd, bool low_bits) 1016 { 1017 const int max_bit = ilog2(MMC_VDD_35_36); 1018 int bit; 1019 1020 if (vdd < 1650 || vdd > 3600) 1021 return -EINVAL; 1022 1023 if (vdd >= 1650 && vdd <= 1950) 1024 return ilog2(MMC_VDD_165_195); 1025 1026 if (low_bits) 1027 vdd -= 1; 1028 1029 /* Base 2000 mV, step 100 mV, bit's base 8. */ 1030 bit = (vdd - 2000) / 100 + 8; 1031 if (bit > max_bit) 1032 return max_bit; 1033 return bit; 1034 } 1035 1036 /** 1037 * mmc_vddrange_to_ocrmask - Convert a voltage range to the OCR mask 1038 * @vdd_min: minimum voltage value (mV) 1039 * @vdd_max: maximum voltage value (mV) 1040 * 1041 * This function returns the OCR mask bits according to the provided @vdd_min 1042 * and @vdd_max values. If conversion is not possible the function returns 0. 1043 * 1044 * Notes wrt boundary cases: 1045 * This function sets the OCR bits for all boundary voltages, for example 1046 * [3300:3400] range is translated to MMC_VDD_32_33 | MMC_VDD_33_34 | 1047 * MMC_VDD_34_35 mask. 1048 */ 1049 u32 mmc_vddrange_to_ocrmask(int vdd_min, int vdd_max) 1050 { 1051 u32 mask = 0; 1052 1053 if (vdd_max < vdd_min) 1054 return 0; 1055 1056 /* Prefer high bits for the boundary vdd_max values. */ 1057 vdd_max = mmc_vdd_to_ocrbitnum(vdd_max, false); 1058 if (vdd_max < 0) 1059 return 0; 1060 1061 /* Prefer low bits for the boundary vdd_min values. */ 1062 vdd_min = mmc_vdd_to_ocrbitnum(vdd_min, true); 1063 if (vdd_min < 0) 1064 return 0; 1065 1066 /* Fill the mask, from max bit to min bit. */ 1067 while (vdd_max >= vdd_min) 1068 mask |= 1 << vdd_max--; 1069 1070 return mask; 1071 } 1072 1073 static int mmc_of_get_func_num(struct device_node *node) 1074 { 1075 u32 reg; 1076 int ret; 1077 1078 ret = of_property_read_u32(node, "reg", ®); 1079 if (ret < 0) 1080 return ret; 1081 1082 return reg; 1083 } 1084 1085 struct device_node *mmc_of_find_child_device(struct mmc_host *host, 1086 unsigned func_num) 1087 { 1088 struct device_node *node; 1089 1090 if (!host->parent || !host->parent->of_node) 1091 return NULL; 1092 1093 for_each_child_of_node(host->parent->of_node, node) { 1094 if (mmc_of_get_func_num(node) == func_num) 1095 return node; 1096 } 1097 1098 return NULL; 1099 } 1100 1101 /* 1102 * Mask off any voltages we don't support and select 1103 * the lowest voltage 1104 */ 1105 u32 mmc_select_voltage(struct mmc_host *host, u32 ocr) 1106 { 1107 int bit; 1108 1109 /* 1110 * Sanity check the voltages that the card claims to 1111 * support. 1112 */ 1113 if (ocr & 0x7F) { 1114 dev_warn(mmc_dev(host), 1115 "card claims to support voltages below defined range\n"); 1116 ocr &= ~0x7F; 1117 } 1118 1119 ocr &= host->ocr_avail; 1120 if (!ocr) { 1121 dev_warn(mmc_dev(host), "no support for card's volts\n"); 1122 return 0; 1123 } 1124 1125 if (host->caps2 & MMC_CAP2_FULL_PWR_CYCLE) { 1126 bit = ffs(ocr) - 1; 1127 ocr &= 3 << bit; 1128 mmc_power_cycle(host, ocr); 1129 } else { 1130 bit = fls(ocr) - 1; 1131 ocr &= 3 << bit; 1132 if (bit != host->ios.vdd) 1133 dev_warn(mmc_dev(host), "exceeding card's volts\n"); 1134 } 1135 1136 return ocr; 1137 } 1138 1139 int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage) 1140 { 1141 int err = 0; 1142 int old_signal_voltage = host->ios.signal_voltage; 1143 1144 host->ios.signal_voltage = signal_voltage; 1145 if (host->ops->start_signal_voltage_switch) 1146 err = host->ops->start_signal_voltage_switch(host, &host->ios); 1147 1148 if (err) 1149 host->ios.signal_voltage = old_signal_voltage; 1150 1151 return err; 1152 1153 } 1154 1155 void mmc_set_initial_signal_voltage(struct mmc_host *host) 1156 { 1157 /* Try to set signal voltage to 3.3V but fall back to 1.8v or 1.2v */ 1158 if (!mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330)) 1159 dev_dbg(mmc_dev(host), "Initial signal voltage of 3.3v\n"); 1160 else if (!mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180)) 1161 dev_dbg(mmc_dev(host), "Initial signal voltage of 1.8v\n"); 1162 else if (!mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120)) 1163 dev_dbg(mmc_dev(host), "Initial signal voltage of 1.2v\n"); 1164 } 1165 1166 int mmc_host_set_uhs_voltage(struct mmc_host *host) 1167 { 1168 u32 clock; 1169 1170 /* 1171 * During a signal voltage level switch, the clock must be gated 1172 * for 5 ms according to the SD spec 1173 */ 1174 clock = host->ios.clock; 1175 host->ios.clock = 0; 1176 mmc_set_ios(host); 1177 1178 if (mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180)) 1179 return -EAGAIN; 1180 1181 /* Keep clock gated for at least 10 ms, though spec only says 5 ms */ 1182 mmc_delay(10); 1183 host->ios.clock = clock; 1184 mmc_set_ios(host); 1185 1186 return 0; 1187 } 1188 1189 int mmc_set_uhs_voltage(struct mmc_host *host, u32 ocr) 1190 { 1191 struct mmc_command cmd = {}; 1192 int err = 0; 1193 1194 /* 1195 * If we cannot switch voltages, return failure so the caller 1196 * can continue without UHS mode 1197 */ 1198 if (!host->ops->start_signal_voltage_switch) 1199 return -EPERM; 1200 if (!host->ops->card_busy) 1201 pr_warn("%s: cannot verify signal voltage switch\n", 1202 mmc_hostname(host)); 1203 1204 cmd.opcode = SD_SWITCH_VOLTAGE; 1205 cmd.arg = 0; 1206 cmd.flags = MMC_RSP_R1 | MMC_CMD_AC; 1207 1208 err = mmc_wait_for_cmd(host, &cmd, 0); 1209 if (err) 1210 goto power_cycle; 1211 1212 if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) 1213 return -EIO; 1214 1215 /* 1216 * The card should drive cmd and dat[0:3] low immediately 1217 * after the response of cmd11, but wait 1 ms to be sure 1218 */ 1219 mmc_delay(1); 1220 if (host->ops->card_busy && !host->ops->card_busy(host)) { 1221 err = -EAGAIN; 1222 goto power_cycle; 1223 } 1224 1225 if (mmc_host_set_uhs_voltage(host)) { 1226 /* 1227 * Voltages may not have been switched, but we've already 1228 * sent CMD11, so a power cycle is required anyway 1229 */ 1230 err = -EAGAIN; 1231 goto power_cycle; 1232 } 1233 1234 /* Wait for at least 1 ms according to spec */ 1235 mmc_delay(1); 1236 1237 /* 1238 * Failure to switch is indicated by the card holding 1239 * dat[0:3] low 1240 */ 1241 if (host->ops->card_busy && host->ops->card_busy(host)) 1242 err = -EAGAIN; 1243 1244 power_cycle: 1245 if (err) { 1246 pr_debug("%s: Signal voltage switch failed, " 1247 "power cycling card\n", mmc_hostname(host)); 1248 mmc_power_cycle(host, ocr); 1249 } 1250 1251 return err; 1252 } 1253 1254 /* 1255 * Select timing parameters for host. 1256 */ 1257 void mmc_set_timing(struct mmc_host *host, unsigned int timing) 1258 { 1259 host->ios.timing = timing; 1260 mmc_set_ios(host); 1261 } 1262 1263 /* 1264 * Select appropriate driver type for host. 1265 */ 1266 void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type) 1267 { 1268 host->ios.drv_type = drv_type; 1269 mmc_set_ios(host); 1270 } 1271 1272 int mmc_select_drive_strength(struct mmc_card *card, unsigned int max_dtr, 1273 int card_drv_type, int *drv_type) 1274 { 1275 struct mmc_host *host = card->host; 1276 int host_drv_type = SD_DRIVER_TYPE_B; 1277 1278 *drv_type = 0; 1279 1280 if (!host->ops->select_drive_strength) 1281 return 0; 1282 1283 /* Use SD definition of driver strength for hosts */ 1284 if (host->caps & MMC_CAP_DRIVER_TYPE_A) 1285 host_drv_type |= SD_DRIVER_TYPE_A; 1286 1287 if (host->caps & MMC_CAP_DRIVER_TYPE_C) 1288 host_drv_type |= SD_DRIVER_TYPE_C; 1289 1290 if (host->caps & MMC_CAP_DRIVER_TYPE_D) 1291 host_drv_type |= SD_DRIVER_TYPE_D; 1292 1293 /* 1294 * The drive strength that the hardware can support 1295 * depends on the board design. Pass the appropriate 1296 * information and let the hardware specific code 1297 * return what is possible given the options 1298 */ 1299 return host->ops->select_drive_strength(card, max_dtr, 1300 host_drv_type, 1301 card_drv_type, 1302 drv_type); 1303 } 1304 1305 /* 1306 * Apply power to the MMC stack. This is a two-stage process. 1307 * First, we enable power to the card without the clock running. 1308 * We then wait a bit for the power to stabilise. Finally, 1309 * enable the bus drivers and clock to the card. 1310 * 1311 * We must _NOT_ enable the clock prior to power stablising. 1312 * 1313 * If a host does all the power sequencing itself, ignore the 1314 * initial MMC_POWER_UP stage. 1315 */ 1316 void mmc_power_up(struct mmc_host *host, u32 ocr) 1317 { 1318 if (host->ios.power_mode == MMC_POWER_ON) 1319 return; 1320 1321 mmc_pwrseq_pre_power_on(host); 1322 1323 host->ios.vdd = fls(ocr) - 1; 1324 host->ios.power_mode = MMC_POWER_UP; 1325 /* Set initial state and call mmc_set_ios */ 1326 mmc_set_initial_state(host); 1327 1328 mmc_set_initial_signal_voltage(host); 1329 1330 /* 1331 * This delay should be sufficient to allow the power supply 1332 * to reach the minimum voltage. 1333 */ 1334 mmc_delay(host->ios.power_delay_ms); 1335 1336 mmc_pwrseq_post_power_on(host); 1337 1338 host->ios.clock = host->f_init; 1339 1340 host->ios.power_mode = MMC_POWER_ON; 1341 mmc_set_ios(host); 1342 1343 /* 1344 * This delay must be at least 74 clock sizes, or 1 ms, or the 1345 * time required to reach a stable voltage. 1346 */ 1347 mmc_delay(host->ios.power_delay_ms); 1348 } 1349 1350 void mmc_power_off(struct mmc_host *host) 1351 { 1352 if (host->ios.power_mode == MMC_POWER_OFF) 1353 return; 1354 1355 mmc_pwrseq_power_off(host); 1356 1357 host->ios.clock = 0; 1358 host->ios.vdd = 0; 1359 1360 host->ios.power_mode = MMC_POWER_OFF; 1361 /* Set initial state and call mmc_set_ios */ 1362 mmc_set_initial_state(host); 1363 1364 /* 1365 * Some configurations, such as the 802.11 SDIO card in the OLPC 1366 * XO-1.5, require a short delay after poweroff before the card 1367 * can be successfully turned on again. 1368 */ 1369 mmc_delay(1); 1370 } 1371 1372 void mmc_power_cycle(struct mmc_host *host, u32 ocr) 1373 { 1374 mmc_power_off(host); 1375 /* Wait at least 1 ms according to SD spec */ 1376 mmc_delay(1); 1377 mmc_power_up(host, ocr); 1378 } 1379 1380 /* 1381 * Assign a mmc bus handler to a host. Only one bus handler may control a 1382 * host at any given time. 1383 */ 1384 void mmc_attach_bus(struct mmc_host *host, const struct mmc_bus_ops *ops) 1385 { 1386 host->bus_ops = ops; 1387 } 1388 1389 /* 1390 * Remove the current bus handler from a host. 1391 */ 1392 void mmc_detach_bus(struct mmc_host *host) 1393 { 1394 host->bus_ops = NULL; 1395 } 1396 1397 void _mmc_detect_change(struct mmc_host *host, unsigned long delay, bool cd_irq) 1398 { 1399 /* 1400 * Prevent system sleep for 5s to allow user space to consume the 1401 * corresponding uevent. This is especially useful, when CD irq is used 1402 * as a system wakeup, but doesn't hurt in other cases. 1403 */ 1404 if (cd_irq && !(host->caps & MMC_CAP_NEEDS_POLL)) 1405 __pm_wakeup_event(host->ws, 5000); 1406 1407 host->detect_change = 1; 1408 mmc_schedule_delayed_work(&host->detect, delay); 1409 } 1410 1411 /** 1412 * mmc_detect_change - process change of state on a MMC socket 1413 * @host: host which changed state. 1414 * @delay: optional delay to wait before detection (jiffies) 1415 * 1416 * MMC drivers should call this when they detect a card has been 1417 * inserted or removed. The MMC layer will confirm that any 1418 * present card is still functional, and initialize any newly 1419 * inserted. 1420 */ 1421 void mmc_detect_change(struct mmc_host *host, unsigned long delay) 1422 { 1423 _mmc_detect_change(host, delay, true); 1424 } 1425 EXPORT_SYMBOL(mmc_detect_change); 1426 1427 void mmc_init_erase(struct mmc_card *card) 1428 { 1429 unsigned int sz; 1430 1431 if (is_power_of_2(card->erase_size)) 1432 card->erase_shift = ffs(card->erase_size) - 1; 1433 else 1434 card->erase_shift = 0; 1435 1436 /* 1437 * It is possible to erase an arbitrarily large area of an SD or MMC 1438 * card. That is not desirable because it can take a long time 1439 * (minutes) potentially delaying more important I/O, and also the 1440 * timeout calculations become increasingly hugely over-estimated. 1441 * Consequently, 'pref_erase' is defined as a guide to limit erases 1442 * to that size and alignment. 1443 * 1444 * For SD cards that define Allocation Unit size, limit erases to one 1445 * Allocation Unit at a time. 1446 * For MMC, have a stab at ai good value and for modern cards it will 1447 * end up being 4MiB. Note that if the value is too small, it can end 1448 * up taking longer to erase. Also note, erase_size is already set to 1449 * High Capacity Erase Size if available when this function is called. 1450 */ 1451 if (mmc_card_sd(card) && card->ssr.au) { 1452 card->pref_erase = card->ssr.au; 1453 card->erase_shift = ffs(card->ssr.au) - 1; 1454 } else if (card->erase_size) { 1455 sz = (card->csd.capacity << (card->csd.read_blkbits - 9)) >> 11; 1456 if (sz < 128) 1457 card->pref_erase = 512 * 1024 / 512; 1458 else if (sz < 512) 1459 card->pref_erase = 1024 * 1024 / 512; 1460 else if (sz < 1024) 1461 card->pref_erase = 2 * 1024 * 1024 / 512; 1462 else 1463 card->pref_erase = 4 * 1024 * 1024 / 512; 1464 if (card->pref_erase < card->erase_size) 1465 card->pref_erase = card->erase_size; 1466 else { 1467 sz = card->pref_erase % card->erase_size; 1468 if (sz) 1469 card->pref_erase += card->erase_size - sz; 1470 } 1471 } else 1472 card->pref_erase = 0; 1473 } 1474 1475 static unsigned int mmc_mmc_erase_timeout(struct mmc_card *card, 1476 unsigned int arg, unsigned int qty) 1477 { 1478 unsigned int erase_timeout; 1479 1480 if (arg == MMC_DISCARD_ARG || 1481 (arg == MMC_TRIM_ARG && card->ext_csd.rev >= 6)) { 1482 erase_timeout = card->ext_csd.trim_timeout; 1483 } else if (card->ext_csd.erase_group_def & 1) { 1484 /* High Capacity Erase Group Size uses HC timeouts */ 1485 if (arg == MMC_TRIM_ARG) 1486 erase_timeout = card->ext_csd.trim_timeout; 1487 else 1488 erase_timeout = card->ext_csd.hc_erase_timeout; 1489 } else { 1490 /* CSD Erase Group Size uses write timeout */ 1491 unsigned int mult = (10 << card->csd.r2w_factor); 1492 unsigned int timeout_clks = card->csd.taac_clks * mult; 1493 unsigned int timeout_us; 1494 1495 /* Avoid overflow: e.g. taac_ns=80000000 mult=1280 */ 1496 if (card->csd.taac_ns < 1000000) 1497 timeout_us = (card->csd.taac_ns * mult) / 1000; 1498 else 1499 timeout_us = (card->csd.taac_ns / 1000) * mult; 1500 1501 /* 1502 * ios.clock is only a target. The real clock rate might be 1503 * less but not that much less, so fudge it by multiplying by 2. 1504 */ 1505 timeout_clks <<= 1; 1506 timeout_us += (timeout_clks * 1000) / 1507 (card->host->ios.clock / 1000); 1508 1509 erase_timeout = timeout_us / 1000; 1510 1511 /* 1512 * Theoretically, the calculation could underflow so round up 1513 * to 1ms in that case. 1514 */ 1515 if (!erase_timeout) 1516 erase_timeout = 1; 1517 } 1518 1519 /* Multiplier for secure operations */ 1520 if (arg & MMC_SECURE_ARGS) { 1521 if (arg == MMC_SECURE_ERASE_ARG) 1522 erase_timeout *= card->ext_csd.sec_erase_mult; 1523 else 1524 erase_timeout *= card->ext_csd.sec_trim_mult; 1525 } 1526 1527 erase_timeout *= qty; 1528 1529 /* 1530 * Ensure at least a 1 second timeout for SPI as per 1531 * 'mmc_set_data_timeout()' 1532 */ 1533 if (mmc_host_is_spi(card->host) && erase_timeout < 1000) 1534 erase_timeout = 1000; 1535 1536 return erase_timeout; 1537 } 1538 1539 static unsigned int mmc_sd_erase_timeout(struct mmc_card *card, 1540 unsigned int arg, 1541 unsigned int qty) 1542 { 1543 unsigned int erase_timeout; 1544 1545 /* for DISCARD none of the below calculation applies. 1546 * the busy timeout is 250msec per discard command. 1547 */ 1548 if (arg == SD_DISCARD_ARG) 1549 return SD_DISCARD_TIMEOUT_MS; 1550 1551 if (card->ssr.erase_timeout) { 1552 /* Erase timeout specified in SD Status Register (SSR) */ 1553 erase_timeout = card->ssr.erase_timeout * qty + 1554 card->ssr.erase_offset; 1555 } else { 1556 /* 1557 * Erase timeout not specified in SD Status Register (SSR) so 1558 * use 250ms per write block. 1559 */ 1560 erase_timeout = 250 * qty; 1561 } 1562 1563 /* Must not be less than 1 second */ 1564 if (erase_timeout < 1000) 1565 erase_timeout = 1000; 1566 1567 return erase_timeout; 1568 } 1569 1570 static unsigned int mmc_erase_timeout(struct mmc_card *card, 1571 unsigned int arg, 1572 unsigned int qty) 1573 { 1574 if (mmc_card_sd(card)) 1575 return mmc_sd_erase_timeout(card, arg, qty); 1576 else 1577 return mmc_mmc_erase_timeout(card, arg, qty); 1578 } 1579 1580 static int mmc_do_erase(struct mmc_card *card, unsigned int from, 1581 unsigned int to, unsigned int arg) 1582 { 1583 struct mmc_command cmd = {}; 1584 unsigned int qty = 0, busy_timeout = 0; 1585 bool use_r1b_resp = false; 1586 int err; 1587 1588 mmc_retune_hold(card->host); 1589 1590 /* 1591 * qty is used to calculate the erase timeout which depends on how many 1592 * erase groups (or allocation units in SD terminology) are affected. 1593 * We count erasing part of an erase group as one erase group. 1594 * For SD, the allocation units are always a power of 2. For MMC, the 1595 * erase group size is almost certainly also power of 2, but it does not 1596 * seem to insist on that in the JEDEC standard, so we fall back to 1597 * division in that case. SD may not specify an allocation unit size, 1598 * in which case the timeout is based on the number of write blocks. 1599 * 1600 * Note that the timeout for secure trim 2 will only be correct if the 1601 * number of erase groups specified is the same as the total of all 1602 * preceding secure trim 1 commands. Since the power may have been 1603 * lost since the secure trim 1 commands occurred, it is generally 1604 * impossible to calculate the secure trim 2 timeout correctly. 1605 */ 1606 if (card->erase_shift) 1607 qty += ((to >> card->erase_shift) - 1608 (from >> card->erase_shift)) + 1; 1609 else if (mmc_card_sd(card)) 1610 qty += to - from + 1; 1611 else 1612 qty += ((to / card->erase_size) - 1613 (from / card->erase_size)) + 1; 1614 1615 if (!mmc_card_blockaddr(card)) { 1616 from <<= 9; 1617 to <<= 9; 1618 } 1619 1620 if (mmc_card_sd(card)) 1621 cmd.opcode = SD_ERASE_WR_BLK_START; 1622 else 1623 cmd.opcode = MMC_ERASE_GROUP_START; 1624 cmd.arg = from; 1625 cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; 1626 err = mmc_wait_for_cmd(card->host, &cmd, 0); 1627 if (err) { 1628 pr_err("mmc_erase: group start error %d, " 1629 "status %#x\n", err, cmd.resp[0]); 1630 err = -EIO; 1631 goto out; 1632 } 1633 1634 memset(&cmd, 0, sizeof(struct mmc_command)); 1635 if (mmc_card_sd(card)) 1636 cmd.opcode = SD_ERASE_WR_BLK_END; 1637 else 1638 cmd.opcode = MMC_ERASE_GROUP_END; 1639 cmd.arg = to; 1640 cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; 1641 err = mmc_wait_for_cmd(card->host, &cmd, 0); 1642 if (err) { 1643 pr_err("mmc_erase: group end error %d, status %#x\n", 1644 err, cmd.resp[0]); 1645 err = -EIO; 1646 goto out; 1647 } 1648 1649 memset(&cmd, 0, sizeof(struct mmc_command)); 1650 cmd.opcode = MMC_ERASE; 1651 cmd.arg = arg; 1652 busy_timeout = mmc_erase_timeout(card, arg, qty); 1653 /* 1654 * If the host controller supports busy signalling and the timeout for 1655 * the erase operation does not exceed the max_busy_timeout, we should 1656 * use R1B response. Or we need to prevent the host from doing hw busy 1657 * detection, which is done by converting to a R1 response instead. 1658 * Note, some hosts requires R1B, which also means they are on their own 1659 * when it comes to deal with the busy timeout. 1660 */ 1661 if (!(card->host->caps & MMC_CAP_NEED_RSP_BUSY) && 1662 card->host->max_busy_timeout && 1663 busy_timeout > card->host->max_busy_timeout) { 1664 cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; 1665 } else { 1666 cmd.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC; 1667 cmd.busy_timeout = busy_timeout; 1668 use_r1b_resp = true; 1669 } 1670 1671 err = mmc_wait_for_cmd(card->host, &cmd, 0); 1672 if (err) { 1673 pr_err("mmc_erase: erase error %d, status %#x\n", 1674 err, cmd.resp[0]); 1675 err = -EIO; 1676 goto out; 1677 } 1678 1679 if (mmc_host_is_spi(card->host)) 1680 goto out; 1681 1682 /* 1683 * In case of when R1B + MMC_CAP_WAIT_WHILE_BUSY is used, the polling 1684 * shall be avoided. 1685 */ 1686 if ((card->host->caps & MMC_CAP_WAIT_WHILE_BUSY) && use_r1b_resp) 1687 goto out; 1688 1689 /* Let's poll to find out when the erase operation completes. */ 1690 err = mmc_poll_for_busy(card, busy_timeout, MMC_BUSY_ERASE); 1691 1692 out: 1693 mmc_retune_release(card->host); 1694 return err; 1695 } 1696 1697 static unsigned int mmc_align_erase_size(struct mmc_card *card, 1698 unsigned int *from, 1699 unsigned int *to, 1700 unsigned int nr) 1701 { 1702 unsigned int from_new = *from, nr_new = nr, rem; 1703 1704 /* 1705 * When the 'card->erase_size' is power of 2, we can use round_up/down() 1706 * to align the erase size efficiently. 1707 */ 1708 if (is_power_of_2(card->erase_size)) { 1709 unsigned int temp = from_new; 1710 1711 from_new = round_up(temp, card->erase_size); 1712 rem = from_new - temp; 1713 1714 if (nr_new > rem) 1715 nr_new -= rem; 1716 else 1717 return 0; 1718 1719 nr_new = round_down(nr_new, card->erase_size); 1720 } else { 1721 rem = from_new % card->erase_size; 1722 if (rem) { 1723 rem = card->erase_size - rem; 1724 from_new += rem; 1725 if (nr_new > rem) 1726 nr_new -= rem; 1727 else 1728 return 0; 1729 } 1730 1731 rem = nr_new % card->erase_size; 1732 if (rem) 1733 nr_new -= rem; 1734 } 1735 1736 if (nr_new == 0) 1737 return 0; 1738 1739 *to = from_new + nr_new; 1740 *from = from_new; 1741 1742 return nr_new; 1743 } 1744 1745 /** 1746 * mmc_erase - erase sectors. 1747 * @card: card to erase 1748 * @from: first sector to erase 1749 * @nr: number of sectors to erase 1750 * @arg: erase command argument 1751 * 1752 * Caller must claim host before calling this function. 1753 */ 1754 int mmc_erase(struct mmc_card *card, unsigned int from, unsigned int nr, 1755 unsigned int arg) 1756 { 1757 unsigned int rem, to = from + nr; 1758 int err; 1759 1760 if (!(card->csd.cmdclass & CCC_ERASE)) 1761 return -EOPNOTSUPP; 1762 1763 if (!card->erase_size) 1764 return -EOPNOTSUPP; 1765 1766 if (mmc_card_sd(card) && arg != SD_ERASE_ARG && arg != SD_DISCARD_ARG) 1767 return -EOPNOTSUPP; 1768 1769 if (mmc_card_mmc(card) && (arg & MMC_SECURE_ARGS) && 1770 !(card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN)) 1771 return -EOPNOTSUPP; 1772 1773 if (mmc_card_mmc(card) && (arg & MMC_TRIM_ARGS) && 1774 !(card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN)) 1775 return -EOPNOTSUPP; 1776 1777 if (arg == MMC_SECURE_ERASE_ARG) { 1778 if (from % card->erase_size || nr % card->erase_size) 1779 return -EINVAL; 1780 } 1781 1782 if (arg == MMC_ERASE_ARG) 1783 nr = mmc_align_erase_size(card, &from, &to, nr); 1784 1785 if (nr == 0) 1786 return 0; 1787 1788 if (to <= from) 1789 return -EINVAL; 1790 1791 /* 'from' and 'to' are inclusive */ 1792 to -= 1; 1793 1794 /* 1795 * Special case where only one erase-group fits in the timeout budget: 1796 * If the region crosses an erase-group boundary on this particular 1797 * case, we will be trimming more than one erase-group which, does not 1798 * fit in the timeout budget of the controller, so we need to split it 1799 * and call mmc_do_erase() twice if necessary. This special case is 1800 * identified by the card->eg_boundary flag. 1801 */ 1802 rem = card->erase_size - (from % card->erase_size); 1803 if ((arg & MMC_TRIM_ARGS) && (card->eg_boundary) && (nr > rem)) { 1804 err = mmc_do_erase(card, from, from + rem - 1, arg); 1805 from += rem; 1806 if ((err) || (to <= from)) 1807 return err; 1808 } 1809 1810 return mmc_do_erase(card, from, to, arg); 1811 } 1812 EXPORT_SYMBOL(mmc_erase); 1813 1814 int mmc_can_erase(struct mmc_card *card) 1815 { 1816 if (card->csd.cmdclass & CCC_ERASE && card->erase_size) 1817 return 1; 1818 return 0; 1819 } 1820 EXPORT_SYMBOL(mmc_can_erase); 1821 1822 int mmc_can_trim(struct mmc_card *card) 1823 { 1824 if ((card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN) && 1825 (!(card->quirks & MMC_QUIRK_TRIM_BROKEN))) 1826 return 1; 1827 return 0; 1828 } 1829 EXPORT_SYMBOL(mmc_can_trim); 1830 1831 int mmc_can_discard(struct mmc_card *card) 1832 { 1833 /* 1834 * As there's no way to detect the discard support bit at v4.5 1835 * use the s/w feature support filed. 1836 */ 1837 if (card->ext_csd.feature_support & MMC_DISCARD_FEATURE) 1838 return 1; 1839 return 0; 1840 } 1841 EXPORT_SYMBOL(mmc_can_discard); 1842 1843 int mmc_can_sanitize(struct mmc_card *card) 1844 { 1845 if (!mmc_can_trim(card) && !mmc_can_erase(card)) 1846 return 0; 1847 if (card->ext_csd.sec_feature_support & EXT_CSD_SEC_SANITIZE) 1848 return 1; 1849 return 0; 1850 } 1851 1852 int mmc_can_secure_erase_trim(struct mmc_card *card) 1853 { 1854 if ((card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN) && 1855 !(card->quirks & MMC_QUIRK_SEC_ERASE_TRIM_BROKEN)) 1856 return 1; 1857 return 0; 1858 } 1859 EXPORT_SYMBOL(mmc_can_secure_erase_trim); 1860 1861 int mmc_erase_group_aligned(struct mmc_card *card, unsigned int from, 1862 unsigned int nr) 1863 { 1864 if (!card->erase_size) 1865 return 0; 1866 if (from % card->erase_size || nr % card->erase_size) 1867 return 0; 1868 return 1; 1869 } 1870 EXPORT_SYMBOL(mmc_erase_group_aligned); 1871 1872 static unsigned int mmc_do_calc_max_discard(struct mmc_card *card, 1873 unsigned int arg) 1874 { 1875 struct mmc_host *host = card->host; 1876 unsigned int max_discard, x, y, qty = 0, max_qty, min_qty, timeout; 1877 unsigned int last_timeout = 0; 1878 unsigned int max_busy_timeout = host->max_busy_timeout ? 1879 host->max_busy_timeout : MMC_ERASE_TIMEOUT_MS; 1880 1881 if (card->erase_shift) { 1882 max_qty = UINT_MAX >> card->erase_shift; 1883 min_qty = card->pref_erase >> card->erase_shift; 1884 } else if (mmc_card_sd(card)) { 1885 max_qty = UINT_MAX; 1886 min_qty = card->pref_erase; 1887 } else { 1888 max_qty = UINT_MAX / card->erase_size; 1889 min_qty = card->pref_erase / card->erase_size; 1890 } 1891 1892 /* 1893 * We should not only use 'host->max_busy_timeout' as the limitation 1894 * when deciding the max discard sectors. We should set a balance value 1895 * to improve the erase speed, and it can not get too long timeout at 1896 * the same time. 1897 * 1898 * Here we set 'card->pref_erase' as the minimal discard sectors no 1899 * matter what size of 'host->max_busy_timeout', but if the 1900 * 'host->max_busy_timeout' is large enough for more discard sectors, 1901 * then we can continue to increase the max discard sectors until we 1902 * get a balance value. In cases when the 'host->max_busy_timeout' 1903 * isn't specified, use the default max erase timeout. 1904 */ 1905 do { 1906 y = 0; 1907 for (x = 1; x && x <= max_qty && max_qty - x >= qty; x <<= 1) { 1908 timeout = mmc_erase_timeout(card, arg, qty + x); 1909 1910 if (qty + x > min_qty && timeout > max_busy_timeout) 1911 break; 1912 1913 if (timeout < last_timeout) 1914 break; 1915 last_timeout = timeout; 1916 y = x; 1917 } 1918 qty += y; 1919 } while (y); 1920 1921 if (!qty) 1922 return 0; 1923 1924 /* 1925 * When specifying a sector range to trim, chances are we might cross 1926 * an erase-group boundary even if the amount of sectors is less than 1927 * one erase-group. 1928 * If we can only fit one erase-group in the controller timeout budget, 1929 * we have to care that erase-group boundaries are not crossed by a 1930 * single trim operation. We flag that special case with "eg_boundary". 1931 * In all other cases we can just decrement qty and pretend that we 1932 * always touch (qty + 1) erase-groups as a simple optimization. 1933 */ 1934 if (qty == 1) 1935 card->eg_boundary = 1; 1936 else 1937 qty--; 1938 1939 /* Convert qty to sectors */ 1940 if (card->erase_shift) 1941 max_discard = qty << card->erase_shift; 1942 else if (mmc_card_sd(card)) 1943 max_discard = qty + 1; 1944 else 1945 max_discard = qty * card->erase_size; 1946 1947 return max_discard; 1948 } 1949 1950 unsigned int mmc_calc_max_discard(struct mmc_card *card) 1951 { 1952 struct mmc_host *host = card->host; 1953 unsigned int max_discard, max_trim; 1954 1955 /* 1956 * Without erase_group_def set, MMC erase timeout depends on clock 1957 * frequence which can change. In that case, the best choice is 1958 * just the preferred erase size. 1959 */ 1960 if (mmc_card_mmc(card) && !(card->ext_csd.erase_group_def & 1)) 1961 return card->pref_erase; 1962 1963 max_discard = mmc_do_calc_max_discard(card, MMC_ERASE_ARG); 1964 if (mmc_can_trim(card)) { 1965 max_trim = mmc_do_calc_max_discard(card, MMC_TRIM_ARG); 1966 if (max_trim < max_discard || max_discard == 0) 1967 max_discard = max_trim; 1968 } else if (max_discard < card->erase_size) { 1969 max_discard = 0; 1970 } 1971 pr_debug("%s: calculated max. discard sectors %u for timeout %u ms\n", 1972 mmc_hostname(host), max_discard, host->max_busy_timeout ? 1973 host->max_busy_timeout : MMC_ERASE_TIMEOUT_MS); 1974 return max_discard; 1975 } 1976 EXPORT_SYMBOL(mmc_calc_max_discard); 1977 1978 bool mmc_card_is_blockaddr(struct mmc_card *card) 1979 { 1980 return card ? mmc_card_blockaddr(card) : false; 1981 } 1982 EXPORT_SYMBOL(mmc_card_is_blockaddr); 1983 1984 int mmc_set_blocklen(struct mmc_card *card, unsigned int blocklen) 1985 { 1986 struct mmc_command cmd = {}; 1987 1988 if (mmc_card_blockaddr(card) || mmc_card_ddr52(card) || 1989 mmc_card_hs400(card) || mmc_card_hs400es(card)) 1990 return 0; 1991 1992 cmd.opcode = MMC_SET_BLOCKLEN; 1993 cmd.arg = blocklen; 1994 cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; 1995 return mmc_wait_for_cmd(card->host, &cmd, 5); 1996 } 1997 EXPORT_SYMBOL(mmc_set_blocklen); 1998 1999 static void mmc_hw_reset_for_init(struct mmc_host *host) 2000 { 2001 mmc_pwrseq_reset(host); 2002 2003 if (!(host->caps & MMC_CAP_HW_RESET) || !host->ops->hw_reset) 2004 return; 2005 host->ops->hw_reset(host); 2006 } 2007 2008 /** 2009 * mmc_hw_reset - reset the card in hardware 2010 * @host: MMC host to which the card is attached 2011 * 2012 * Hard reset the card. This function is only for upper layers, like the 2013 * block layer or card drivers. You cannot use it in host drivers (struct 2014 * mmc_card might be gone then). 2015 * 2016 * Return: 0 on success, -errno on failure 2017 */ 2018 int mmc_hw_reset(struct mmc_host *host) 2019 { 2020 int ret; 2021 2022 ret = host->bus_ops->hw_reset(host); 2023 if (ret < 0) 2024 pr_warn("%s: tried to HW reset card, got error %d\n", 2025 mmc_hostname(host), ret); 2026 2027 return ret; 2028 } 2029 EXPORT_SYMBOL(mmc_hw_reset); 2030 2031 int mmc_sw_reset(struct mmc_host *host) 2032 { 2033 int ret; 2034 2035 if (!host->bus_ops->sw_reset) 2036 return -EOPNOTSUPP; 2037 2038 ret = host->bus_ops->sw_reset(host); 2039 if (ret) 2040 pr_warn("%s: tried to SW reset card, got error %d\n", 2041 mmc_hostname(host), ret); 2042 2043 return ret; 2044 } 2045 EXPORT_SYMBOL(mmc_sw_reset); 2046 2047 static int mmc_rescan_try_freq(struct mmc_host *host, unsigned freq) 2048 { 2049 host->f_init = freq; 2050 2051 pr_debug("%s: %s: trying to init card at %u Hz\n", 2052 mmc_hostname(host), __func__, host->f_init); 2053 2054 mmc_power_up(host, host->ocr_avail); 2055 2056 /* 2057 * Some eMMCs (with VCCQ always on) may not be reset after power up, so 2058 * do a hardware reset if possible. 2059 */ 2060 mmc_hw_reset_for_init(host); 2061 2062 /* 2063 * sdio_reset sends CMD52 to reset card. Since we do not know 2064 * if the card is being re-initialized, just send it. CMD52 2065 * should be ignored by SD/eMMC cards. 2066 * Skip it if we already know that we do not support SDIO commands 2067 */ 2068 if (!(host->caps2 & MMC_CAP2_NO_SDIO)) 2069 sdio_reset(host); 2070 2071 mmc_go_idle(host); 2072 2073 if (!(host->caps2 & MMC_CAP2_NO_SD)) { 2074 if (mmc_send_if_cond_pcie(host, host->ocr_avail)) 2075 goto out; 2076 if (mmc_card_sd_express(host)) 2077 return 0; 2078 } 2079 2080 /* Order's important: probe SDIO, then SD, then MMC */ 2081 if (!(host->caps2 & MMC_CAP2_NO_SDIO)) 2082 if (!mmc_attach_sdio(host)) 2083 return 0; 2084 2085 if (!(host->caps2 & MMC_CAP2_NO_SD)) 2086 if (!mmc_attach_sd(host)) 2087 return 0; 2088 2089 if (!(host->caps2 & MMC_CAP2_NO_MMC)) 2090 if (!mmc_attach_mmc(host)) 2091 return 0; 2092 2093 out: 2094 mmc_power_off(host); 2095 return -EIO; 2096 } 2097 2098 int _mmc_detect_card_removed(struct mmc_host *host) 2099 { 2100 int ret; 2101 2102 if (!host->card || mmc_card_removed(host->card)) 2103 return 1; 2104 2105 ret = host->bus_ops->alive(host); 2106 2107 /* 2108 * Card detect status and alive check may be out of sync if card is 2109 * removed slowly, when card detect switch changes while card/slot 2110 * pads are still contacted in hardware (refer to "SD Card Mechanical 2111 * Addendum, Appendix C: Card Detection Switch"). So reschedule a 2112 * detect work 200ms later for this case. 2113 */ 2114 if (!ret && host->ops->get_cd && !host->ops->get_cd(host)) { 2115 mmc_detect_change(host, msecs_to_jiffies(200)); 2116 pr_debug("%s: card removed too slowly\n", mmc_hostname(host)); 2117 } 2118 2119 if (ret) { 2120 mmc_card_set_removed(host->card); 2121 pr_debug("%s: card remove detected\n", mmc_hostname(host)); 2122 } 2123 2124 return ret; 2125 } 2126 2127 int mmc_detect_card_removed(struct mmc_host *host) 2128 { 2129 struct mmc_card *card = host->card; 2130 int ret; 2131 2132 WARN_ON(!host->claimed); 2133 2134 if (!card) 2135 return 1; 2136 2137 if (!mmc_card_is_removable(host)) 2138 return 0; 2139 2140 ret = mmc_card_removed(card); 2141 /* 2142 * The card will be considered unchanged unless we have been asked to 2143 * detect a change or host requires polling to provide card detection. 2144 */ 2145 if (!host->detect_change && !(host->caps & MMC_CAP_NEEDS_POLL)) 2146 return ret; 2147 2148 host->detect_change = 0; 2149 if (!ret) { 2150 ret = _mmc_detect_card_removed(host); 2151 if (ret && (host->caps & MMC_CAP_NEEDS_POLL)) { 2152 /* 2153 * Schedule a detect work as soon as possible to let a 2154 * rescan handle the card removal. 2155 */ 2156 cancel_delayed_work(&host->detect); 2157 _mmc_detect_change(host, 0, false); 2158 } 2159 } 2160 2161 return ret; 2162 } 2163 EXPORT_SYMBOL(mmc_detect_card_removed); 2164 2165 void mmc_rescan(struct work_struct *work) 2166 { 2167 struct mmc_host *host = 2168 container_of(work, struct mmc_host, detect.work); 2169 int i; 2170 2171 if (host->rescan_disable) 2172 return; 2173 2174 /* If there is a non-removable card registered, only scan once */ 2175 if (!mmc_card_is_removable(host) && host->rescan_entered) 2176 return; 2177 host->rescan_entered = 1; 2178 2179 if (host->trigger_card_event && host->ops->card_event) { 2180 mmc_claim_host(host); 2181 host->ops->card_event(host); 2182 mmc_release_host(host); 2183 host->trigger_card_event = false; 2184 } 2185 2186 /* Verify a registered card to be functional, else remove it. */ 2187 if (host->bus_ops) 2188 host->bus_ops->detect(host); 2189 2190 host->detect_change = 0; 2191 2192 /* if there still is a card present, stop here */ 2193 if (host->bus_ops != NULL) 2194 goto out; 2195 2196 mmc_claim_host(host); 2197 if (mmc_card_is_removable(host) && host->ops->get_cd && 2198 host->ops->get_cd(host) == 0) { 2199 mmc_power_off(host); 2200 mmc_release_host(host); 2201 goto out; 2202 } 2203 2204 /* If an SD express card is present, then leave it as is. */ 2205 if (mmc_card_sd_express(host)) { 2206 mmc_release_host(host); 2207 goto out; 2208 } 2209 2210 for (i = 0; i < ARRAY_SIZE(freqs); i++) { 2211 unsigned int freq = freqs[i]; 2212 if (freq > host->f_max) { 2213 if (i + 1 < ARRAY_SIZE(freqs)) 2214 continue; 2215 freq = host->f_max; 2216 } 2217 if (!mmc_rescan_try_freq(host, max(freq, host->f_min))) 2218 break; 2219 if (freqs[i] <= host->f_min) 2220 break; 2221 } 2222 mmc_release_host(host); 2223 2224 out: 2225 if (host->caps & MMC_CAP_NEEDS_POLL) 2226 mmc_schedule_delayed_work(&host->detect, HZ); 2227 } 2228 2229 void mmc_start_host(struct mmc_host *host) 2230 { 2231 host->f_init = max(min(freqs[0], host->f_max), host->f_min); 2232 host->rescan_disable = 0; 2233 2234 if (!(host->caps2 & MMC_CAP2_NO_PRESCAN_POWERUP)) { 2235 mmc_claim_host(host); 2236 mmc_power_up(host, host->ocr_avail); 2237 mmc_release_host(host); 2238 } 2239 2240 mmc_gpiod_request_cd_irq(host); 2241 _mmc_detect_change(host, 0, false); 2242 } 2243 2244 void mmc_stop_host(struct mmc_host *host) 2245 { 2246 if (host->slot.cd_irq >= 0) { 2247 mmc_gpio_set_cd_wake(host, false); 2248 disable_irq(host->slot.cd_irq); 2249 } 2250 2251 host->rescan_disable = 1; 2252 cancel_delayed_work_sync(&host->detect); 2253 2254 /* clear pm flags now and let card drivers set them as needed */ 2255 host->pm_flags = 0; 2256 2257 if (host->bus_ops) { 2258 /* Calling bus_ops->remove() with a claimed host can deadlock */ 2259 host->bus_ops->remove(host); 2260 mmc_claim_host(host); 2261 mmc_detach_bus(host); 2262 mmc_power_off(host); 2263 mmc_release_host(host); 2264 return; 2265 } 2266 2267 mmc_claim_host(host); 2268 mmc_power_off(host); 2269 mmc_release_host(host); 2270 } 2271 2272 static int __init mmc_init(void) 2273 { 2274 int ret; 2275 2276 ret = mmc_register_bus(); 2277 if (ret) 2278 return ret; 2279 2280 ret = mmc_register_host_class(); 2281 if (ret) 2282 goto unregister_bus; 2283 2284 ret = sdio_register_bus(); 2285 if (ret) 2286 goto unregister_host_class; 2287 2288 return 0; 2289 2290 unregister_host_class: 2291 mmc_unregister_host_class(); 2292 unregister_bus: 2293 mmc_unregister_bus(); 2294 return ret; 2295 } 2296 2297 static void __exit mmc_exit(void) 2298 { 2299 sdio_unregister_bus(); 2300 mmc_unregister_host_class(); 2301 mmc_unregister_bus(); 2302 } 2303 2304 subsys_initcall(mmc_init); 2305 module_exit(mmc_exit); 2306 2307 MODULE_LICENSE("GPL"); 2308