1menu "EEPROM support" 2 3config EEPROM_AT24 4 tristate "I2C EEPROMs from most vendors" 5 depends on I2C && SYSFS 6 help 7 Enable this driver to get read/write support to most I2C EEPROMs, 8 after you configure the driver to know about each EEPROM on 9 your target board. Use these generic chip names, instead of 10 vendor-specific ones like at24c64 or 24lc02: 11 12 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08, 13 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024 14 15 Unless you like data loss puzzles, always be sure that any chip 16 you configure as a 24c32 (32 kbit) or larger is NOT really a 17 24c16 (16 kbit) or smaller, and vice versa. Marking the chip 18 as read-only won't help recover from this. Also, if your chip 19 has any software write-protect mechanism you may want to review the 20 code to make sure this driver won't turn it on by accident. 21 22 If you use this with an SMBus adapter instead of an I2C adapter, 23 full functionality is not available. Only smaller devices are 24 supported (24c16 and below, max 4 kByte). 25 26 This driver can also be built as a module. If so, the module 27 will be called at24. 28 29config EEPROM_AT25 30 tristate "SPI EEPROMs from most vendors" 31 depends on SPI && SYSFS 32 help 33 Enable this driver to get read/write support to most SPI EEPROMs, 34 after you configure the board init code to know about each eeprom 35 on your target board. 36 37 This driver can also be built as a module. If so, the module 38 will be called at25. 39 40config EEPROM_LEGACY 41 tristate "Old I2C EEPROM reader" 42 depends on I2C && SYSFS 43 help 44 If you say yes here you get read-only access to the EEPROM data 45 available on modern memory DIMMs and Sony Vaio laptops via I2C. Such 46 EEPROMs could theoretically be available on other devices as well. 47 48 This driver can also be built as a module. If so, the module 49 will be called eeprom. 50 51config EEPROM_MAX6875 52 tristate "Maxim MAX6874/5 power supply supervisor" 53 depends on I2C && EXPERIMENTAL 54 help 55 If you say yes here you get read-only support for the user EEPROM of 56 the Maxim MAX6874/5 EEPROM-programmable, quad power-supply 57 sequencer/supervisor. 58 59 All other features of this chip should be accessed via i2c-dev. 60 61 This driver can also be built as a module. If so, the module 62 will be called max6875. 63 64 65config EEPROM_93CX6 66 tristate "EEPROM 93CX6 support" 67 help 68 This is a driver for the EEPROM chipsets 93c46 and 93c66. 69 The driver supports both read as well as write commands. 70 71 If unsure, say N. 72 73config EEPROM_93XX46 74 tristate "Microwire EEPROM 93XX46 support" 75 depends on SPI && SYSFS 76 help 77 Driver for the microwire EEPROM chipsets 93xx46x. The driver 78 supports both read and write commands and also the command to 79 erase the whole EEPROM. 80 81 This driver can also be built as a module. If so, the module 82 will be called eeprom_93xx46. 83 84 If unsure, say N. 85 86config EEPROM_DIGSY_MTC_CFG 87 bool "DigsyMTC display configuration EEPROMs device" 88 depends on GPIO_MPC5200 && SPI_GPIO 89 help 90 This option enables access to display configuration EEPROMs 91 on digsy_mtc board. You have to additionally select Microwire 92 EEPROM 93XX46 driver. sysfs entries will be created for that 93 EEPROM allowing to read/write the configuration data or to 94 erase the whole EEPROM. 95 96 If unsure, say N. 97 98endmenu 99