1# 2# Misc strange devices 3# 4 5menu "Misc devices" 6 7config SENSORS_LIS3LV02D 8 tristate 9 depends on INPUT 10 select INPUT_POLLDEV 11 default n 12 13config AD525X_DPOT 14 tristate "Analog Devices Digital Potentiometers" 15 depends on (I2C || SPI) && SYSFS 16 help 17 If you say yes here, you get support for the Analog Devices 18 AD5258, AD5259, AD5251, AD5252, AD5253, AD5254, AD5255 19 AD5160, AD5161, AD5162, AD5165, AD5200, AD5201, AD5203, 20 AD5204, AD5206, AD5207, AD5231, AD5232, AD5233, AD5235, 21 AD5260, AD5262, AD5263, AD5290, AD5291, AD5292, AD5293, 22 AD7376, AD8400, AD8402, AD8403, ADN2850, AD5241, AD5242, 23 AD5243, AD5245, AD5246, AD5247, AD5248, AD5280, AD5282, 24 ADN2860, AD5273, AD5171, AD5170, AD5172, AD5173, AD5270, 25 AD5271, AD5272, AD5274 26 digital potentiometer chips. 27 28 See Documentation/misc-devices/ad525x_dpot.txt for the 29 userspace interface. 30 31 This driver can also be built as a module. If so, the module 32 will be called ad525x_dpot. 33 34config AD525X_DPOT_I2C 35 tristate "support I2C bus connection" 36 depends on AD525X_DPOT && I2C 37 help 38 Say Y here if you have a digital potentiometers hooked to an I2C bus. 39 40 To compile this driver as a module, choose M here: the 41 module will be called ad525x_dpot-i2c. 42 43config AD525X_DPOT_SPI 44 tristate "support SPI bus connection" 45 depends on AD525X_DPOT && SPI_MASTER 46 help 47 Say Y here if you have a digital potentiometers hooked to an SPI bus. 48 49 If unsure, say N (but it's safe to say "Y"). 50 51 To compile this driver as a module, choose M here: the 52 module will be called ad525x_dpot-spi. 53 54config ATMEL_TCLIB 55 bool "Atmel AT32/AT91 Timer/Counter Library" 56 depends on ARCH_AT91 57 help 58 Select this if you want a library to allocate the Timer/Counter 59 blocks found on many Atmel processors. This facilitates using 60 these blocks by different drivers despite processor differences. 61 62config ATMEL_TCB_CLKSRC 63 bool "TC Block Clocksource" 64 depends on ATMEL_TCLIB 65 default y 66 help 67 Select this to get a high precision clocksource based on a 68 TC block with a 5+ MHz base clock rate. Two timer channels 69 are combined to make a single 32-bit timer. 70 71 When GENERIC_CLOCKEVENTS is defined, the third timer channel 72 may be used as a clock event device supporting oneshot mode 73 (delays of up to two seconds) based on the 32 KiHz clock. 74 75config ATMEL_TCB_CLKSRC_BLOCK 76 int 77 depends on ATMEL_TCB_CLKSRC 78 default 0 79 range 0 1 80 help 81 Some chips provide more than one TC block, so you have the 82 choice of which one to use for the clock framework. The other 83 TC can be used for other purposes, such as PWM generation and 84 interval timing. 85 86config DUMMY_IRQ 87 tristate "Dummy IRQ handler" 88 default n 89 ---help--- 90 This module accepts a single 'irq' parameter, which it should register for. 91 The sole purpose of this module is to help with debugging of systems on 92 which spurious IRQs would happen on disabled IRQ vector. 93 94config IBM_ASM 95 tristate "Device driver for IBM RSA service processor" 96 depends on X86 && PCI && INPUT 97 depends on SERIAL_8250 || SERIAL_8250=n 98 ---help--- 99 This option enables device driver support for in-band access to the 100 IBM RSA (Condor) service processor in eServer xSeries systems. 101 The ibmasm device driver allows user space application to access 102 ASM (Advanced Systems Management) functions on the service 103 processor. The driver is meant to be used in conjunction with 104 a user space API. 105 The ibmasm driver also enables the OS to use the UART on the 106 service processor board as a regular serial port. To make use of 107 this feature serial driver support (CONFIG_SERIAL_8250) must be 108 enabled. 109 110 WARNING: This software may not be supported or function 111 correctly on your IBM server. Please consult the IBM ServerProven 112 website <http://www-03.ibm.com/systems/info/x86servers/serverproven/compat/us/> 113 for information on the specific driver level and support statement 114 for your IBM server. 115 116config IBMVMC 117 tristate "IBM Virtual Management Channel support" 118 depends on PPC_PSERIES 119 help 120 This is the IBM POWER Virtual Management Channel 121 122 This driver is to be used for the POWER Virtual 123 Management Channel virtual adapter on the PowerVM 124 platform. It provides both request/response and 125 async message support through the /dev/ibmvmc node. 126 127 To compile this driver as a module, choose M here: the 128 module will be called ibmvmc. 129 130config PHANTOM 131 tristate "Sensable PHANToM (PCI)" 132 depends on PCI 133 help 134 Say Y here if you want to build a driver for Sensable PHANToM device. 135 136 This driver is only for PCI PHANToMs. 137 138 If you choose to build module, its name will be phantom. If unsure, 139 say N here. 140 141config INTEL_MID_PTI 142 tristate "Parallel Trace Interface for MIPI P1149.7 cJTAG standard" 143 depends on PCI && TTY && (X86_INTEL_MID || COMPILE_TEST) 144 default n 145 help 146 The PTI (Parallel Trace Interface) driver directs 147 trace data routed from various parts in the system out 148 through an Intel Penwell PTI port and out of the mobile 149 device for analysis with a debugging tool (Lauterbach or Fido). 150 151 You should select this driver if the target kernel is meant for 152 an Intel Atom (non-netbook) mobile device containing a MIPI 153 P1149.7 standard implementation. 154 155config SGI_IOC4 156 tristate "SGI IOC4 Base IO support" 157 depends on PCI 158 ---help--- 159 This option enables basic support for the IOC4 chip on certain 160 SGI IO controller cards (IO9, IO10, and PCI-RT). This option 161 does not enable any specific functions on such a card, but provides 162 necessary infrastructure for other drivers to utilize. 163 164 If you have an SGI Altix with an IOC4-based card say Y. 165 Otherwise say N. 166 167config TIFM_CORE 168 tristate "TI Flash Media interface support" 169 depends on PCI 170 help 171 If you want support for Texas Instruments(R) Flash Media adapters 172 you should select this option and then also choose an appropriate 173 host adapter, such as 'TI Flash Media PCI74xx/PCI76xx host adapter 174 support', if you have a TI PCI74xx compatible card reader, for 175 example. 176 You will also have to select some flash card format drivers. MMC/SD 177 cards are supported via 'MMC/SD Card support: TI Flash Media MMC/SD 178 Interface support (MMC_TIFM_SD)'. 179 180 To compile this driver as a module, choose M here: the module will 181 be called tifm_core. 182 183config TIFM_7XX1 184 tristate "TI Flash Media PCI74xx/PCI76xx host adapter support" 185 depends on PCI && TIFM_CORE 186 default TIFM_CORE 187 help 188 This option enables support for Texas Instruments(R) PCI74xx and 189 PCI76xx families of Flash Media adapters, found in many laptops. 190 To make actual use of the device, you will have to select some 191 flash card format drivers, as outlined in the TIFM_CORE Help. 192 193 To compile this driver as a module, choose M here: the module will 194 be called tifm_7xx1. 195 196config ICS932S401 197 tristate "Integrated Circuits ICS932S401" 198 depends on I2C 199 help 200 If you say yes here you get support for the Integrated Circuits 201 ICS932S401 clock control chips. 202 203 This driver can also be built as a module. If so, the module 204 will be called ics932s401. 205 206config ATMEL_SSC 207 tristate "Device driver for Atmel SSC peripheral" 208 depends on HAS_IOMEM && (ARCH_AT91 || COMPILE_TEST) 209 ---help--- 210 This option enables device driver support for Atmel Synchronized 211 Serial Communication peripheral (SSC). 212 213 The SSC peripheral supports a wide variety of serial frame based 214 communications, i.e. I2S, SPI, etc. 215 216 If unsure, say N. 217 218config ENCLOSURE_SERVICES 219 tristate "Enclosure Services" 220 default n 221 help 222 Provides support for intelligent enclosures (bays which 223 contain storage devices). You also need either a host 224 driver (SCSI/ATA) which supports enclosures 225 or a SCSI enclosure device (SES) to use these services. 226 227config SGI_XP 228 tristate "Support communication between SGI SSIs" 229 depends on NET 230 depends on (IA64_GENERIC || IA64_SGI_SN2 || IA64_SGI_UV || X86_UV) && SMP 231 select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2 232 select GENERIC_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2 233 select SGI_GRU if X86_64 && SMP 234 ---help--- 235 An SGI machine can be divided into multiple Single System 236 Images which act independently of each other and have 237 hardware based memory protection from the others. Enabling 238 this feature will allow for direct communication between SSIs 239 based on a network adapter and DMA messaging. 240 241config CS5535_MFGPT 242 tristate "CS5535/CS5536 Geode Multi-Function General Purpose Timer (MFGPT) support" 243 depends on MFD_CS5535 244 default n 245 help 246 This driver provides access to MFGPT functionality for other 247 drivers that need timers. MFGPTs are available in the CS5535 and 248 CS5536 companion chips that are found in AMD Geode and several 249 other platforms. They have a better resolution and max interval 250 than the generic PIT, and are suitable for use as high-res timers. 251 You probably don't want to enable this manually; other drivers that 252 make use of it should enable it. 253 254config CS5535_MFGPT_DEFAULT_IRQ 255 int 256 depends on CS5535_MFGPT 257 default 7 258 help 259 MFGPTs on the CS5535 require an interrupt. The selected IRQ 260 can be overridden as a module option as well as by driver that 261 use the cs5535_mfgpt_ API; however, different architectures might 262 want to use a different IRQ by default. This is here for 263 architectures to set as necessary. 264 265config CS5535_CLOCK_EVENT_SRC 266 tristate "CS5535/CS5536 high-res timer (MFGPT) events" 267 depends on GENERIC_CLOCKEVENTS && CS5535_MFGPT 268 help 269 This driver provides a clock event source based on the MFGPT 270 timer(s) in the CS5535 and CS5536 companion chips. 271 MFGPTs have a better resolution and max interval than the 272 generic PIT, and are suitable for use as high-res timers. 273 274config HP_ILO 275 tristate "Channel interface driver for the HP iLO processor" 276 depends on PCI 277 default n 278 help 279 The channel interface driver allows applications to communicate 280 with iLO management processors present on HP ProLiant servers. 281 Upon loading, the driver creates /dev/hpilo/dXccbN files, which 282 can be used to gather data from the management processor, via 283 read and write system calls. 284 285 To compile this driver as a module, choose M here: the 286 module will be called hpilo. 287 288config QCOM_COINCELL 289 tristate "Qualcomm coincell charger support" 290 depends on MFD_SPMI_PMIC || COMPILE_TEST 291 help 292 This driver supports the coincell block found inside of 293 Qualcomm PMICs. The coincell charger provides a means to 294 charge a coincell battery or backup capacitor which is used 295 to maintain PMIC register and RTC state in the absence of 296 external power. 297 298config QCOM_FASTRPC 299 tristate "Qualcomm FastRPC" 300 depends on ARCH_QCOM || COMPILE_TEST 301 depends on RPMSG 302 select DMA_SHARED_BUFFER 303 help 304 Provides a communication mechanism that allows for clients to 305 make remote method invocations across processor boundary to 306 applications DSP processor. Say M if you want to enable this 307 module. 308 309config SGI_GRU 310 tristate "SGI GRU driver" 311 depends on X86_UV && SMP 312 default n 313 select MMU_NOTIFIER 314 ---help--- 315 The GRU is a hardware resource located in the system chipset. The GRU 316 contains memory that can be mmapped into the user address space. This memory is 317 used to communicate with the GRU to perform functions such as load/store, 318 scatter/gather, bcopy, AMOs, etc. The GRU is directly accessed by user 319 instructions using user virtual addresses. GRU instructions (ex., bcopy) use 320 user virtual addresses for operands. 321 322 If you are not running on a SGI UV system, say N. 323 324config SGI_GRU_DEBUG 325 bool "SGI GRU driver debug" 326 depends on SGI_GRU 327 default n 328 ---help--- 329 This option enables additional debugging code for the SGI GRU driver. 330 If you are unsure, say N. 331 332config APDS9802ALS 333 tristate "Medfield Avago APDS9802 ALS Sensor module" 334 depends on I2C 335 help 336 If you say yes here you get support for the ALS APDS9802 ambient 337 light sensor. 338 339 This driver can also be built as a module. If so, the module 340 will be called apds9802als. 341 342config ISL29003 343 tristate "Intersil ISL29003 ambient light sensor" 344 depends on I2C && SYSFS 345 help 346 If you say yes here you get support for the Intersil ISL29003 347 ambient light sensor. 348 349 This driver can also be built as a module. If so, the module 350 will be called isl29003. 351 352config ISL29020 353 tristate "Intersil ISL29020 ambient light sensor" 354 depends on I2C 355 help 356 If you say yes here you get support for the Intersil ISL29020 357 ambient light sensor. 358 359 This driver can also be built as a module. If so, the module 360 will be called isl29020. 361 362config SENSORS_TSL2550 363 tristate "Taos TSL2550 ambient light sensor" 364 depends on I2C && SYSFS 365 help 366 If you say yes here you get support for the Taos TSL2550 367 ambient light sensor. 368 369 This driver can also be built as a module. If so, the module 370 will be called tsl2550. 371 372config SENSORS_BH1770 373 tristate "BH1770GLC / SFH7770 combined ALS - Proximity sensor" 374 depends on I2C 375 ---help--- 376 Say Y here if you want to build a driver for BH1770GLC (ROHM) or 377 SFH7770 (Osram) combined ambient light and proximity sensor chip. 378 379 To compile this driver as a module, choose M here: the 380 module will be called bh1770glc. If unsure, say N here. 381 382config SENSORS_APDS990X 383 tristate "APDS990X combined als and proximity sensors" 384 depends on I2C 385 default n 386 ---help--- 387 Say Y here if you want to build a driver for Avago APDS990x 388 combined ambient light and proximity sensor chip. 389 390 To compile this driver as a module, choose M here: the 391 module will be called apds990x. If unsure, say N here. 392 393config HMC6352 394 tristate "Honeywell HMC6352 compass" 395 depends on I2C 396 help 397 This driver provides support for the Honeywell HMC6352 compass, 398 providing configuration and heading data via sysfs. 399 400config DS1682 401 tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm" 402 depends on I2C 403 help 404 If you say yes here you get support for Dallas Semiconductor 405 DS1682 Total Elapsed Time Recorder. 406 407 This driver can also be built as a module. If so, the module 408 will be called ds1682. 409 410config SPEAR13XX_PCIE_GADGET 411 bool "PCIe gadget support for SPEAr13XX platform" 412 depends on ARCH_SPEAR13XX && BROKEN 413 default n 414 help 415 This option enables gadget support for PCIe controller. If 416 board file defines any controller as PCIe endpoint then a sysfs 417 entry will be created for that controller. User can use these 418 sysfs node to configure PCIe EP as per his requirements. 419 420config VMWARE_BALLOON 421 tristate "VMware Balloon Driver" 422 depends on VMWARE_VMCI && X86 && HYPERVISOR_GUEST 423 help 424 This is VMware physical memory management driver which acts 425 like a "balloon" that can be inflated to reclaim physical pages 426 by reserving them in the guest and invalidating them in the 427 monitor, freeing up the underlying machine pages so they can 428 be allocated to other guests. The balloon can also be deflated 429 to allow the guest to use more physical memory. 430 431 If unsure, say N. 432 433 To compile this driver as a module, choose M here: the 434 module will be called vmw_balloon. 435 436config PCH_PHUB 437 tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) PHUB" 438 select GENERIC_NET_UTILS 439 depends on PCI && (X86_32 || MIPS || COMPILE_TEST) 440 help 441 This driver is for PCH(Platform controller Hub) PHUB(Packet Hub) of 442 Intel Topcliff which is an IOH(Input/Output Hub) for x86 embedded 443 processor. The Topcliff has MAC address and Option ROM data in SROM. 444 This driver can access MAC address and Option ROM data in SROM. 445 446 This driver also can be used for LAPIS Semiconductor's IOH, 447 ML7213/ML7223/ML7831. 448 ML7213 which is for IVI(In-Vehicle Infotainment) use. 449 ML7223 IOH is for MP(Media Phone) use. 450 ML7831 IOH is for general purpose use. 451 ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series. 452 ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH. 453 454 To compile this driver as a module, choose M here: the module will 455 be called pch_phub. 456 457config USB_SWITCH_FSA9480 458 tristate "FSA9480 USB Switch" 459 depends on I2C 460 help 461 The FSA9480 is a USB port accessory detector and switch. 462 The FSA9480 is fully controlled using I2C and enables USB data, 463 stereo and mono audio, video, microphone and UART data to use 464 a common connector port. 465 466config LATTICE_ECP3_CONFIG 467 tristate "Lattice ECP3 FPGA bitstream configuration via SPI" 468 depends on SPI && SYSFS 469 select FW_LOADER 470 default n 471 help 472 This option enables support for bitstream configuration (programming 473 or loading) of the Lattice ECP3 FPGA family via SPI. 474 475 If unsure, say N. 476 477config SRAM 478 bool "Generic on-chip SRAM driver" 479 depends on HAS_IOMEM 480 select GENERIC_ALLOCATOR 481 select SRAM_EXEC if ARM 482 help 483 This driver allows you to declare a memory region to be managed by 484 the genalloc API. It is supposed to be used for small on-chip SRAM 485 areas found on many SoCs. 486 487config SRAM_EXEC 488 bool 489 490config VEXPRESS_SYSCFG 491 bool "Versatile Express System Configuration driver" 492 depends on VEXPRESS_CONFIG 493 default y 494 help 495 ARM Ltd. Versatile Express uses specialised platform configuration 496 bus. System Configuration interface is one of the possible means 497 of generating transactions on this bus. 498 499config ASPEED_LPC_CTRL 500 depends on (ARCH_ASPEED || COMPILE_TEST) && REGMAP && MFD_SYSCON 501 tristate "Aspeed ast2400/2500 HOST LPC to BMC bridge control" 502 ---help--- 503 Control Aspeed ast2400/2500 HOST LPC to BMC mappings through 504 ioctl()s, the driver also provides a read/write interface to a BMC ram 505 region where the host LPC read/write region can be buffered. 506 507config ASPEED_LPC_SNOOP 508 tristate "Aspeed ast2500 HOST LPC snoop support" 509 depends on (ARCH_ASPEED || COMPILE_TEST) && REGMAP && MFD_SYSCON 510 help 511 Provides a driver to control the LPC snoop interface which 512 allows the BMC to listen on and save the data written by 513 the host to an arbitrary LPC I/O port. 514 515config PCI_ENDPOINT_TEST 516 depends on PCI 517 select CRC32 518 tristate "PCI Endpoint Test driver" 519 ---help--- 520 Enable this configuration option to enable the host side test driver 521 for PCI Endpoint. 522 523config MISC_RTSX 524 tristate 525 default MISC_RTSX_PCI || MISC_RTSX_USB 526 527config PVPANIC 528 tristate "pvpanic device support" 529 depends on HAS_IOMEM && (ACPI || OF) 530 help 531 This driver provides support for the pvpanic device. pvpanic is 532 a paravirtualized device provided by QEMU; it lets a virtual machine 533 (guest) communicate panic events to the host. 534 535source "drivers/misc/c2port/Kconfig" 536source "drivers/misc/eeprom/Kconfig" 537source "drivers/misc/cb710/Kconfig" 538source "drivers/misc/ti-st/Kconfig" 539source "drivers/misc/lis3lv02d/Kconfig" 540source "drivers/misc/altera-stapl/Kconfig" 541source "drivers/misc/mei/Kconfig" 542source "drivers/misc/vmw_vmci/Kconfig" 543source "drivers/misc/mic/Kconfig" 544source "drivers/misc/genwqe/Kconfig" 545source "drivers/misc/echo/Kconfig" 546source "drivers/misc/cxl/Kconfig" 547source "drivers/misc/ocxl/Kconfig" 548source "drivers/misc/cardreader/Kconfig" 549source "drivers/misc/habanalabs/Kconfig" 550endmenu 551