1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * twl4030-irq.c - TWL4030/TPS659x0 irq support 4 * 5 * Copyright (C) 2005-2006 Texas Instruments, Inc. 6 * 7 * Modifications to defer interrupt handling to a kernel thread: 8 * Copyright (C) 2006 MontaVista Software, Inc. 9 * 10 * Based on tlv320aic23.c: 11 * Copyright (c) by Kai Svahn <kai.svahn@nokia.com> 12 * 13 * Code cleanup and modifications to IRQ handler. 14 * by syed khasim <x0khasim@ti.com> 15 */ 16 17 #include <linux/export.h> 18 #include <linux/interrupt.h> 19 #include <linux/irq.h> 20 #include <linux/slab.h> 21 #include <linux/of.h> 22 #include <linux/irqdomain.h> 23 #include <linux/mfd/twl.h> 24 25 #include "twl-core.h" 26 27 /* 28 * TWL4030 IRQ handling has two stages in hardware, and thus in software. 29 * The Primary Interrupt Handler (PIH) stage exposes status bits saying 30 * which Secondary Interrupt Handler (SIH) stage is raising an interrupt. 31 * SIH modules are more traditional IRQ components, which support per-IRQ 32 * enable/disable and trigger controls; they do most of the work. 33 * 34 * These chips are designed to support IRQ handling from two different 35 * I2C masters. Each has a dedicated IRQ line, and dedicated IRQ status 36 * and mask registers in the PIH and SIH modules. 37 * 38 * We set up IRQs starting at a platform-specified base, always starting 39 * with PIH and the SIH for PWR_INT and then usually adding GPIO: 40 * base + 0 .. base + 7 PIH 41 * base + 8 .. base + 15 SIH for PWR_INT 42 * base + 16 .. base + 33 SIH for GPIO 43 */ 44 #define TWL4030_CORE_NR_IRQS 8 45 #define TWL4030_PWR_NR_IRQS 8 46 47 /* PIH register offsets */ 48 #define REG_PIH_ISR_P1 0x01 49 #define REG_PIH_ISR_P2 0x02 50 #define REG_PIH_SIR 0x03 /* for testing */ 51 52 /* Linux could (eventually) use either IRQ line */ 53 static int irq_line; 54 55 struct sih { 56 char name[8]; 57 u8 module; /* module id */ 58 u8 control_offset; /* for SIH_CTRL */ 59 bool set_cor; 60 61 u8 bits; /* valid in isr/imr */ 62 u8 bytes_ixr; /* bytelen of ISR/IMR/SIR */ 63 64 u8 edr_offset; 65 u8 bytes_edr; /* bytelen of EDR */ 66 67 u8 irq_lines; /* number of supported irq lines */ 68 69 /* SIR ignored -- set interrupt, for testing only */ 70 struct sih_irq_data { 71 u8 isr_offset; 72 u8 imr_offset; 73 } mask[2]; 74 /* + 2 bytes padding */ 75 }; 76 77 static const struct sih *sih_modules; 78 static int nr_sih_modules; 79 80 #define SIH_INITIALIZER(modname, nbits) \ 81 .module = TWL4030_MODULE_ ## modname, \ 82 .control_offset = TWL4030_ ## modname ## _SIH_CTRL, \ 83 .bits = nbits, \ 84 .bytes_ixr = DIV_ROUND_UP(nbits, 8), \ 85 .edr_offset = TWL4030_ ## modname ## _EDR, \ 86 .bytes_edr = DIV_ROUND_UP((2*(nbits)), 8), \ 87 .irq_lines = 2, \ 88 .mask = { { \ 89 .isr_offset = TWL4030_ ## modname ## _ISR1, \ 90 .imr_offset = TWL4030_ ## modname ## _IMR1, \ 91 }, \ 92 { \ 93 .isr_offset = TWL4030_ ## modname ## _ISR2, \ 94 .imr_offset = TWL4030_ ## modname ## _IMR2, \ 95 }, }, 96 97 /* register naming policies are inconsistent ... */ 98 #define TWL4030_INT_PWR_EDR TWL4030_INT_PWR_EDR1 99 #define TWL4030_MODULE_KEYPAD_KEYP TWL4030_MODULE_KEYPAD 100 #define TWL4030_MODULE_INT_PWR TWL4030_MODULE_INT 101 102 103 /* 104 * Order in this table matches order in PIH_ISR. That is, 105 * BIT(n) in PIH_ISR is sih_modules[n]. 106 */ 107 /* sih_modules_twl4030 is used both in twl4030 and twl5030 */ 108 static const struct sih sih_modules_twl4030[6] = { 109 [0] = { 110 .name = "gpio", 111 .module = TWL4030_MODULE_GPIO, 112 .control_offset = REG_GPIO_SIH_CTRL, 113 .set_cor = true, 114 .bits = TWL4030_GPIO_MAX, 115 .bytes_ixr = 3, 116 /* Note: *all* of these IRQs default to no-trigger */ 117 .edr_offset = REG_GPIO_EDR1, 118 .bytes_edr = 5, 119 .irq_lines = 2, 120 .mask = { { 121 .isr_offset = REG_GPIO_ISR1A, 122 .imr_offset = REG_GPIO_IMR1A, 123 }, { 124 .isr_offset = REG_GPIO_ISR1B, 125 .imr_offset = REG_GPIO_IMR1B, 126 }, }, 127 }, 128 [1] = { 129 .name = "keypad", 130 .set_cor = true, 131 SIH_INITIALIZER(KEYPAD_KEYP, 4) 132 }, 133 [2] = { 134 .name = "bci", 135 .module = TWL4030_MODULE_INTERRUPTS, 136 .control_offset = TWL4030_INTERRUPTS_BCISIHCTRL, 137 .set_cor = true, 138 .bits = 12, 139 .bytes_ixr = 2, 140 .edr_offset = TWL4030_INTERRUPTS_BCIEDR1, 141 /* Note: most of these IRQs default to no-trigger */ 142 .bytes_edr = 3, 143 .irq_lines = 2, 144 .mask = { { 145 .isr_offset = TWL4030_INTERRUPTS_BCIISR1A, 146 .imr_offset = TWL4030_INTERRUPTS_BCIIMR1A, 147 }, { 148 .isr_offset = TWL4030_INTERRUPTS_BCIISR1B, 149 .imr_offset = TWL4030_INTERRUPTS_BCIIMR1B, 150 }, }, 151 }, 152 [3] = { 153 .name = "madc", 154 SIH_INITIALIZER(MADC, 4) 155 }, 156 [4] = { 157 /* USB doesn't use the same SIH organization */ 158 .name = "usb", 159 }, 160 [5] = { 161 .name = "power", 162 .set_cor = true, 163 SIH_INITIALIZER(INT_PWR, 8) 164 }, 165 /* there are no SIH modules #6 or #7 ... */ 166 }; 167 168 static const struct sih sih_modules_twl5031[8] = { 169 [0] = { 170 .name = "gpio", 171 .module = TWL4030_MODULE_GPIO, 172 .control_offset = REG_GPIO_SIH_CTRL, 173 .set_cor = true, 174 .bits = TWL4030_GPIO_MAX, 175 .bytes_ixr = 3, 176 /* Note: *all* of these IRQs default to no-trigger */ 177 .edr_offset = REG_GPIO_EDR1, 178 .bytes_edr = 5, 179 .irq_lines = 2, 180 .mask = { { 181 .isr_offset = REG_GPIO_ISR1A, 182 .imr_offset = REG_GPIO_IMR1A, 183 }, { 184 .isr_offset = REG_GPIO_ISR1B, 185 .imr_offset = REG_GPIO_IMR1B, 186 }, }, 187 }, 188 [1] = { 189 .name = "keypad", 190 .set_cor = true, 191 SIH_INITIALIZER(KEYPAD_KEYP, 4) 192 }, 193 [2] = { 194 .name = "bci", 195 .module = TWL5031_MODULE_INTERRUPTS, 196 .control_offset = TWL5031_INTERRUPTS_BCISIHCTRL, 197 .bits = 7, 198 .bytes_ixr = 1, 199 .edr_offset = TWL5031_INTERRUPTS_BCIEDR1, 200 /* Note: most of these IRQs default to no-trigger */ 201 .bytes_edr = 2, 202 .irq_lines = 2, 203 .mask = { { 204 .isr_offset = TWL5031_INTERRUPTS_BCIISR1, 205 .imr_offset = TWL5031_INTERRUPTS_BCIIMR1, 206 }, { 207 .isr_offset = TWL5031_INTERRUPTS_BCIISR2, 208 .imr_offset = TWL5031_INTERRUPTS_BCIIMR2, 209 }, }, 210 }, 211 [3] = { 212 .name = "madc", 213 SIH_INITIALIZER(MADC, 4) 214 }, 215 [4] = { 216 /* USB doesn't use the same SIH organization */ 217 .name = "usb", 218 }, 219 [5] = { 220 .name = "power", 221 .set_cor = true, 222 SIH_INITIALIZER(INT_PWR, 8) 223 }, 224 [6] = { 225 /* 226 * ECI/DBI doesn't use the same SIH organization. 227 * For example, it supports only one interrupt output line. 228 * That is, the interrupts are seen on both INT1 and INT2 lines. 229 */ 230 .name = "eci_dbi", 231 .module = TWL5031_MODULE_ACCESSORY, 232 .bits = 9, 233 .bytes_ixr = 2, 234 .irq_lines = 1, 235 .mask = { { 236 .isr_offset = TWL5031_ACIIDR_LSB, 237 .imr_offset = TWL5031_ACIIMR_LSB, 238 }, }, 239 240 }, 241 [7] = { 242 /* Audio accessory */ 243 .name = "audio", 244 .module = TWL5031_MODULE_ACCESSORY, 245 .control_offset = TWL5031_ACCSIHCTRL, 246 .bits = 2, 247 .bytes_ixr = 1, 248 .edr_offset = TWL5031_ACCEDR1, 249 /* Note: most of these IRQs default to no-trigger */ 250 .bytes_edr = 1, 251 .irq_lines = 2, 252 .mask = { { 253 .isr_offset = TWL5031_ACCISR1, 254 .imr_offset = TWL5031_ACCIMR1, 255 }, { 256 .isr_offset = TWL5031_ACCISR2, 257 .imr_offset = TWL5031_ACCIMR2, 258 }, }, 259 }, 260 }; 261 262 #undef TWL4030_MODULE_KEYPAD_KEYP 263 #undef TWL4030_MODULE_INT_PWR 264 #undef TWL4030_INT_PWR_EDR 265 266 /*----------------------------------------------------------------------*/ 267 268 static unsigned twl4030_irq_base; 269 270 /* 271 * handle_twl4030_pih() is the desc->handle method for the twl4030 interrupt. 272 * This is a chained interrupt, so there is no desc->action method for it. 273 * Now we need to query the interrupt controller in the twl4030 to determine 274 * which module is generating the interrupt request. However, we can't do i2c 275 * transactions in interrupt context, so we must defer that work to a kernel 276 * thread. All we do here is acknowledge and mask the interrupt and wakeup 277 * the kernel thread. 278 */ 279 static irqreturn_t handle_twl4030_pih(int irq, void *devid) 280 { 281 irqreturn_t ret; 282 u8 pih_isr; 283 284 ret = twl_i2c_read_u8(TWL_MODULE_PIH, &pih_isr, 285 REG_PIH_ISR_P1); 286 if (ret) { 287 pr_warn("twl4030: I2C error %d reading PIH ISR\n", ret); 288 return IRQ_NONE; 289 } 290 291 while (pih_isr) { 292 unsigned long pending = __ffs(pih_isr); 293 unsigned int irq; 294 295 pih_isr &= ~BIT(pending); 296 irq = pending + twl4030_irq_base; 297 handle_nested_irq(irq); 298 } 299 300 return IRQ_HANDLED; 301 } 302 303 /*----------------------------------------------------------------------*/ 304 305 /* 306 * twl4030_init_sih_modules() ... start from a known state where no 307 * IRQs will be coming in, and where we can quickly enable them then 308 * handle them as they arrive. Mask all IRQs: maybe init SIH_CTRL. 309 * 310 * NOTE: we don't touch EDR registers here; they stay with hardware 311 * defaults or whatever the last value was. Note that when both EDR 312 * bits for an IRQ are clear, that's as if its IMR bit is set... 313 */ 314 static int twl4030_init_sih_modules(unsigned line) 315 { 316 const struct sih *sih; 317 u8 buf[4]; 318 int i; 319 int status; 320 321 /* line 0 == int1_n signal; line 1 == int2_n signal */ 322 if (line > 1) 323 return -EINVAL; 324 325 irq_line = line; 326 327 /* disable all interrupts on our line */ 328 memset(buf, 0xff, sizeof(buf)); 329 sih = sih_modules; 330 for (i = 0; i < nr_sih_modules; i++, sih++) { 331 /* skip USB -- it's funky */ 332 if (!sih->bytes_ixr) 333 continue; 334 335 /* Not all the SIH modules support multiple interrupt lines */ 336 if (sih->irq_lines <= line) 337 continue; 338 339 status = twl_i2c_write(sih->module, buf, 340 sih->mask[line].imr_offset, sih->bytes_ixr); 341 if (status < 0) 342 pr_err("twl4030: err %d initializing %s %s\n", 343 status, sih->name, "IMR"); 344 345 /* 346 * Maybe disable "exclusive" mode; buffer second pending irq; 347 * set Clear-On-Read (COR) bit. 348 * 349 * NOTE that sometimes COR polarity is documented as being 350 * inverted: for MADC, COR=1 means "clear on write". 351 * And for PWR_INT it's not documented... 352 */ 353 if (sih->set_cor) { 354 status = twl_i2c_write_u8(sih->module, 355 TWL4030_SIH_CTRL_COR_MASK, 356 sih->control_offset); 357 if (status < 0) 358 pr_err("twl4030: err %d initializing %s %s\n", 359 status, sih->name, "SIH_CTRL"); 360 } 361 } 362 363 sih = sih_modules; 364 for (i = 0; i < nr_sih_modules; i++, sih++) { 365 u8 rxbuf[4]; 366 int j; 367 368 /* skip USB */ 369 if (!sih->bytes_ixr) 370 continue; 371 372 /* Not all the SIH modules support multiple interrupt lines */ 373 if (sih->irq_lines <= line) 374 continue; 375 376 /* 377 * Clear pending interrupt status. Either the read was 378 * enough, or we need to write those bits. Repeat, in 379 * case an IRQ is pending (PENDDIS=0) ... that's not 380 * uncommon with PWR_INT.PWRON. 381 */ 382 for (j = 0; j < 2; j++) { 383 status = twl_i2c_read(sih->module, rxbuf, 384 sih->mask[line].isr_offset, sih->bytes_ixr); 385 if (status < 0) 386 pr_warn("twl4030: err %d initializing %s %s\n", 387 status, sih->name, "ISR"); 388 389 if (!sih->set_cor) { 390 status = twl_i2c_write(sih->module, buf, 391 sih->mask[line].isr_offset, 392 sih->bytes_ixr); 393 if (status < 0) 394 pr_warn("twl4030: write failed: %d\n", 395 status); 396 } 397 /* 398 * else COR=1 means read sufficed. 399 * (for most SIH modules...) 400 */ 401 } 402 } 403 404 return 0; 405 } 406 407 static inline void activate_irq(int irq) 408 { 409 irq_clear_status_flags(irq, IRQ_NOREQUEST | IRQ_NOPROBE); 410 } 411 412 /*----------------------------------------------------------------------*/ 413 414 struct sih_agent { 415 int irq_base; 416 const struct sih *sih; 417 418 u32 imr; 419 bool imr_change_pending; 420 421 u32 edge_change; 422 423 struct mutex irq_lock; 424 char *irq_name; 425 }; 426 427 /*----------------------------------------------------------------------*/ 428 429 /* 430 * All irq_chip methods get issued from code holding irq_desc[irq].lock, 431 * which can't perform the underlying I2C operations (because they sleep). 432 * So we must hand them off to a thread (workqueue) and cope with asynch 433 * completion, potentially including some re-ordering, of these requests. 434 */ 435 436 static void twl4030_sih_mask(struct irq_data *data) 437 { 438 struct sih_agent *agent = irq_data_get_irq_chip_data(data); 439 440 agent->imr |= BIT(data->irq - agent->irq_base); 441 agent->imr_change_pending = true; 442 } 443 444 static void twl4030_sih_unmask(struct irq_data *data) 445 { 446 struct sih_agent *agent = irq_data_get_irq_chip_data(data); 447 448 agent->imr &= ~BIT(data->irq - agent->irq_base); 449 agent->imr_change_pending = true; 450 } 451 452 static int twl4030_sih_set_type(struct irq_data *data, unsigned trigger) 453 { 454 struct sih_agent *agent = irq_data_get_irq_chip_data(data); 455 456 if (trigger & ~(IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING)) 457 return -EINVAL; 458 459 if (irqd_get_trigger_type(data) != trigger) 460 agent->edge_change |= BIT(data->irq - agent->irq_base); 461 462 return 0; 463 } 464 465 static void twl4030_sih_bus_lock(struct irq_data *data) 466 { 467 struct sih_agent *agent = irq_data_get_irq_chip_data(data); 468 469 mutex_lock(&agent->irq_lock); 470 } 471 472 static void twl4030_sih_bus_sync_unlock(struct irq_data *data) 473 { 474 struct sih_agent *agent = irq_data_get_irq_chip_data(data); 475 const struct sih *sih = agent->sih; 476 int status; 477 478 if (agent->imr_change_pending) { 479 union { 480 __le32 word; 481 u8 bytes[4]; 482 } imr; 483 484 /* byte[0] gets overwritten as we write ... */ 485 imr.word = cpu_to_le32(agent->imr); 486 agent->imr_change_pending = false; 487 488 /* write the whole mask ... simpler than subsetting it */ 489 status = twl_i2c_write(sih->module, imr.bytes, 490 sih->mask[irq_line].imr_offset, 491 sih->bytes_ixr); 492 if (status) 493 pr_err("twl4030: %s, %s --> %d\n", __func__, 494 "write", status); 495 } 496 497 if (agent->edge_change) { 498 u32 edge_change; 499 u8 bytes[6]; 500 501 edge_change = agent->edge_change; 502 agent->edge_change = 0; 503 504 /* 505 * Read, reserving first byte for write scratch. Yes, this 506 * could be cached for some speedup ... but be careful about 507 * any processor on the other IRQ line, EDR registers are 508 * shared. 509 */ 510 status = twl_i2c_read(sih->module, bytes, 511 sih->edr_offset, sih->bytes_edr); 512 if (status) { 513 pr_err("twl4030: %s, %s --> %d\n", __func__, 514 "read", status); 515 return; 516 } 517 518 /* Modify only the bits we know must change */ 519 while (edge_change) { 520 int i = fls(edge_change) - 1; 521 int byte = i >> 2; 522 int off = (i & 0x3) * 2; 523 unsigned int type; 524 525 bytes[byte] &= ~(0x03 << off); 526 527 type = irq_get_trigger_type(i + agent->irq_base); 528 if (type & IRQ_TYPE_EDGE_RISING) 529 bytes[byte] |= BIT(off + 1); 530 if (type & IRQ_TYPE_EDGE_FALLING) 531 bytes[byte] |= BIT(off + 0); 532 533 edge_change &= ~BIT(i); 534 } 535 536 /* Write */ 537 status = twl_i2c_write(sih->module, bytes, 538 sih->edr_offset, sih->bytes_edr); 539 if (status) 540 pr_err("twl4030: %s, %s --> %d\n", __func__, 541 "write", status); 542 } 543 544 mutex_unlock(&agent->irq_lock); 545 } 546 547 static struct irq_chip twl4030_sih_irq_chip = { 548 .name = "twl4030", 549 .irq_mask = twl4030_sih_mask, 550 .irq_unmask = twl4030_sih_unmask, 551 .irq_set_type = twl4030_sih_set_type, 552 .irq_bus_lock = twl4030_sih_bus_lock, 553 .irq_bus_sync_unlock = twl4030_sih_bus_sync_unlock, 554 .flags = IRQCHIP_SKIP_SET_WAKE, 555 }; 556 557 /*----------------------------------------------------------------------*/ 558 559 static inline int sih_read_isr(const struct sih *sih) 560 { 561 int status; 562 union { 563 u8 bytes[4]; 564 __le32 word; 565 } isr; 566 567 /* FIXME need retry-on-error ... */ 568 569 isr.word = 0; 570 status = twl_i2c_read(sih->module, isr.bytes, 571 sih->mask[irq_line].isr_offset, sih->bytes_ixr); 572 573 return (status < 0) ? status : le32_to_cpu(isr.word); 574 } 575 576 /* 577 * Generic handler for SIH interrupts ... we "know" this is called 578 * in task context, with IRQs enabled. 579 */ 580 static irqreturn_t handle_twl4030_sih(int irq, void *data) 581 { 582 struct sih_agent *agent = irq_get_handler_data(irq); 583 const struct sih *sih = agent->sih; 584 int isr; 585 586 /* reading ISR acks the IRQs, using clear-on-read mode */ 587 isr = sih_read_isr(sih); 588 589 if (isr < 0) { 590 pr_err("twl4030: %s SIH, read ISR error %d\n", 591 sih->name, isr); 592 /* REVISIT: recover; eventually mask it all, etc */ 593 return IRQ_HANDLED; 594 } 595 596 while (isr) { 597 irq = fls(isr); 598 irq--; 599 isr &= ~BIT(irq); 600 601 if (irq < sih->bits) 602 handle_nested_irq(agent->irq_base + irq); 603 else 604 pr_err("twl4030: %s SIH, invalid ISR bit %d\n", 605 sih->name, irq); 606 } 607 return IRQ_HANDLED; 608 } 609 610 /* returns the first IRQ used by this SIH bank, or negative errno */ 611 int twl4030_sih_setup(struct device *dev, int module, int irq_base) 612 { 613 int sih_mod; 614 const struct sih *sih = NULL; 615 struct sih_agent *agent; 616 int i, irq; 617 int status = -EINVAL; 618 619 /* only support modules with standard clear-on-read for now */ 620 for (sih_mod = 0, sih = sih_modules; sih_mod < nr_sih_modules; 621 sih_mod++, sih++) { 622 if (sih->module == module && sih->set_cor) { 623 status = 0; 624 break; 625 } 626 } 627 628 if (status < 0) { 629 dev_err(dev, "module to setup SIH for not found\n"); 630 return status; 631 } 632 633 agent = kzalloc(sizeof(*agent), GFP_KERNEL); 634 if (!agent) 635 return -ENOMEM; 636 637 agent->irq_base = irq_base; 638 agent->sih = sih; 639 agent->imr = ~0; 640 mutex_init(&agent->irq_lock); 641 642 for (i = 0; i < sih->bits; i++) { 643 irq = irq_base + i; 644 645 irq_set_chip_data(irq, agent); 646 irq_set_chip_and_handler(irq, &twl4030_sih_irq_chip, 647 handle_edge_irq); 648 irq_set_nested_thread(irq, 1); 649 activate_irq(irq); 650 } 651 652 /* replace generic PIH handler (handle_simple_irq) */ 653 irq = sih_mod + twl4030_irq_base; 654 irq_set_handler_data(irq, agent); 655 agent->irq_name = kasprintf(GFP_KERNEL, "twl4030_%s", sih->name); 656 status = request_threaded_irq(irq, NULL, handle_twl4030_sih, 657 IRQF_EARLY_RESUME | IRQF_ONESHOT, 658 agent->irq_name ?: sih->name, NULL); 659 660 dev_info(dev, "%s (irq %d) chaining IRQs %d..%d\n", sih->name, 661 irq, irq_base, irq_base + i - 1); 662 663 return status < 0 ? status : irq_base; 664 } 665 666 /* FIXME need a call to reverse twl4030_sih_setup() ... */ 667 668 /*----------------------------------------------------------------------*/ 669 670 /* FIXME pass in which interrupt line we'll use ... */ 671 #define twl_irq_line 0 672 673 int twl4030_init_irq(struct device *dev, int irq_num) 674 { 675 static struct irq_chip twl4030_irq_chip; 676 int status, i; 677 int irq_base, irq_end, nr_irqs; 678 struct device_node *node = dev->of_node; 679 680 /* 681 * TWL core and pwr interrupts must be contiguous because 682 * the hwirqs numbers are defined contiguously from 1 to 15. 683 * Create only one domain for both. 684 */ 685 nr_irqs = TWL4030_PWR_NR_IRQS + TWL4030_CORE_NR_IRQS; 686 687 irq_base = irq_alloc_descs(-1, 0, nr_irqs, 0); 688 if (irq_base < 0) { 689 dev_err(dev, "Fail to allocate IRQ descs\n"); 690 return irq_base; 691 } 692 693 irq_domain_add_legacy(node, nr_irqs, irq_base, 0, 694 &irq_domain_simple_ops, NULL); 695 696 irq_end = irq_base + TWL4030_CORE_NR_IRQS; 697 698 /* 699 * Mask and clear all TWL4030 interrupts since initially we do 700 * not have any TWL4030 module interrupt handlers present 701 */ 702 status = twl4030_init_sih_modules(twl_irq_line); 703 if (status < 0) 704 return status; 705 706 twl4030_irq_base = irq_base; 707 708 /* 709 * Install an irq handler for each of the SIH modules; 710 * clone dummy irq_chip since PIH can't *do* anything 711 */ 712 twl4030_irq_chip = dummy_irq_chip; 713 twl4030_irq_chip.name = "twl4030"; 714 715 twl4030_sih_irq_chip.irq_ack = dummy_irq_chip.irq_ack; 716 717 for (i = irq_base; i < irq_end; i++) { 718 irq_set_chip_and_handler(i, &twl4030_irq_chip, 719 handle_simple_irq); 720 irq_set_nested_thread(i, 1); 721 activate_irq(i); 722 } 723 724 dev_info(dev, "%s (irq %d) chaining IRQs %d..%d\n", "PIH", 725 irq_num, irq_base, irq_end); 726 727 /* ... and the PWR_INT module ... */ 728 status = twl4030_sih_setup(dev, TWL4030_MODULE_INT, irq_end); 729 if (status < 0) { 730 dev_err(dev, "sih_setup PWR INT --> %d\n", status); 731 goto fail; 732 } 733 734 /* install an irq handler to demultiplex the TWL4030 interrupt */ 735 status = request_threaded_irq(irq_num, NULL, handle_twl4030_pih, 736 IRQF_ONESHOT, 737 "TWL4030-PIH", NULL); 738 if (status < 0) { 739 dev_err(dev, "could not claim irq%d: %d\n", irq_num, status); 740 goto fail_rqirq; 741 } 742 enable_irq_wake(irq_num); 743 744 return irq_base; 745 fail_rqirq: 746 /* clean up twl4030_sih_setup */ 747 fail: 748 for (i = irq_base; i < irq_end; i++) { 749 irq_set_nested_thread(i, 0); 750 irq_set_chip_and_handler(i, NULL, NULL); 751 } 752 753 return status; 754 } 755 756 int twl4030_exit_irq(void) 757 { 758 /* FIXME undo twl_init_irq() */ 759 if (twl4030_irq_base) { 760 pr_err("twl4030: can't yet clean up IRQs?\n"); 761 return -ENOSYS; 762 } 763 return 0; 764 } 765 766 int twl4030_init_chip_irq(const char *chip) 767 { 768 if (!strcmp(chip, "twl5031")) { 769 sih_modules = sih_modules_twl5031; 770 nr_sih_modules = ARRAY_SIZE(sih_modules_twl5031); 771 } else { 772 sih_modules = sih_modules_twl4030; 773 nr_sih_modules = ARRAY_SIZE(sih_modules_twl4030); 774 } 775 776 return 0; 777 } 778