1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * DDR PHY Front End (DPFE) driver for Broadcom set top box SoCs 4 * 5 * Copyright (c) 2017 Broadcom 6 */ 7 8 /* 9 * This driver provides access to the DPFE interface of Broadcom STB SoCs. 10 * The firmware running on the DCPU inside the DDR PHY can provide current 11 * information about the system's RAM, for instance the DRAM refresh rate. 12 * This can be used as an indirect indicator for the DRAM's temperature. 13 * Slower refresh rate means cooler RAM, higher refresh rate means hotter 14 * RAM. 15 * 16 * Throughout the driver, we use readl_relaxed() and writel_relaxed(), which 17 * already contain the appropriate le32_to_cpu()/cpu_to_le32() calls. 18 * 19 * Note regarding the loading of the firmware image: we use be32_to_cpu() 20 * and le_32_to_cpu(), so we can support the following four cases: 21 * - LE kernel + LE firmware image (the most common case) 22 * - LE kernel + BE firmware image 23 * - BE kernel + LE firmware image 24 * - BE kernel + BE firmware image 25 * 26 * The DPCU always runs in big endian mode. The firmware image, however, can 27 * be in either format. Also, communication between host CPU and DCPU is 28 * always in little endian. 29 */ 30 31 #include <linux/delay.h> 32 #include <linux/firmware.h> 33 #include <linux/io.h> 34 #include <linux/module.h> 35 #include <linux/of_address.h> 36 #include <linux/of_device.h> 37 #include <linux/platform_device.h> 38 39 #define DRVNAME "brcmstb-dpfe" 40 41 /* DCPU register offsets */ 42 #define REG_DCPU_RESET 0x0 43 #define REG_TO_DCPU_MBOX 0x10 44 #define REG_TO_HOST_MBOX 0x14 45 46 /* Macros to process offsets returned by the DCPU */ 47 #define DRAM_MSG_ADDR_OFFSET 0x0 48 #define DRAM_MSG_TYPE_OFFSET 0x1c 49 #define DRAM_MSG_ADDR_MASK ((1UL << DRAM_MSG_TYPE_OFFSET) - 1) 50 #define DRAM_MSG_TYPE_MASK ((1UL << \ 51 (BITS_PER_LONG - DRAM_MSG_TYPE_OFFSET)) - 1) 52 53 /* Message RAM */ 54 #define DCPU_MSG_RAM_START 0x100 55 #define DCPU_MSG_RAM(x) (DCPU_MSG_RAM_START + (x) * sizeof(u32)) 56 57 /* DRAM Info Offsets & Masks */ 58 #define DRAM_INFO_INTERVAL 0x0 59 #define DRAM_INFO_MR4 0x4 60 #define DRAM_INFO_ERROR 0x8 61 #define DRAM_INFO_MR4_MASK 0xff 62 #define DRAM_INFO_MR4_SHIFT 24 /* We need to look at byte 3 */ 63 64 /* DRAM MR4 Offsets & Masks */ 65 #define DRAM_MR4_REFRESH 0x0 /* Refresh rate */ 66 #define DRAM_MR4_SR_ABORT 0x3 /* Self Refresh Abort */ 67 #define DRAM_MR4_PPRE 0x4 /* Post-package repair entry/exit */ 68 #define DRAM_MR4_TH_OFFS 0x5 /* Thermal Offset; vendor specific */ 69 #define DRAM_MR4_TUF 0x7 /* Temperature Update Flag */ 70 71 #define DRAM_MR4_REFRESH_MASK 0x7 72 #define DRAM_MR4_SR_ABORT_MASK 0x1 73 #define DRAM_MR4_PPRE_MASK 0x1 74 #define DRAM_MR4_TH_OFFS_MASK 0x3 75 #define DRAM_MR4_TUF_MASK 0x1 76 77 /* DRAM Vendor Offsets & Masks (API v2) */ 78 #define DRAM_VENDOR_MR5 0x0 79 #define DRAM_VENDOR_MR6 0x4 80 #define DRAM_VENDOR_MR7 0x8 81 #define DRAM_VENDOR_MR8 0xc 82 #define DRAM_VENDOR_ERROR 0x10 83 #define DRAM_VENDOR_MASK 0xff 84 #define DRAM_VENDOR_SHIFT 24 /* We need to look at byte 3 */ 85 86 /* DRAM Information Offsets & Masks (API v3) */ 87 #define DRAM_DDR_INFO_MR4 0x0 88 #define DRAM_DDR_INFO_MR5 0x4 89 #define DRAM_DDR_INFO_MR6 0x8 90 #define DRAM_DDR_INFO_MR7 0xc 91 #define DRAM_DDR_INFO_MR8 0x10 92 #define DRAM_DDR_INFO_ERROR 0x14 93 #define DRAM_DDR_INFO_MASK 0xff 94 95 /* Reset register bits & masks */ 96 #define DCPU_RESET_SHIFT 0x0 97 #define DCPU_RESET_MASK 0x1 98 #define DCPU_CLK_DISABLE_SHIFT 0x2 99 100 /* DCPU return codes */ 101 #define DCPU_RET_ERROR_BIT BIT(31) 102 #define DCPU_RET_SUCCESS 0x1 103 #define DCPU_RET_ERR_HEADER (DCPU_RET_ERROR_BIT | BIT(0)) 104 #define DCPU_RET_ERR_INVAL (DCPU_RET_ERROR_BIT | BIT(1)) 105 #define DCPU_RET_ERR_CHKSUM (DCPU_RET_ERROR_BIT | BIT(2)) 106 #define DCPU_RET_ERR_COMMAND (DCPU_RET_ERROR_BIT | BIT(3)) 107 /* This error code is not firmware defined and only used in the driver. */ 108 #define DCPU_RET_ERR_TIMEDOUT (DCPU_RET_ERROR_BIT | BIT(4)) 109 110 /* Firmware magic */ 111 #define DPFE_BE_MAGIC 0xfe1010fe 112 #define DPFE_LE_MAGIC 0xfe0101fe 113 114 /* Error codes */ 115 #define ERR_INVALID_MAGIC -1 116 #define ERR_INVALID_SIZE -2 117 #define ERR_INVALID_CHKSUM -3 118 119 /* Message types */ 120 #define DPFE_MSG_TYPE_COMMAND 1 121 #define DPFE_MSG_TYPE_RESPONSE 2 122 123 #define DELAY_LOOP_MAX 1000 124 125 enum dpfe_msg_fields { 126 MSG_HEADER, 127 MSG_COMMAND, 128 MSG_ARG_COUNT, 129 MSG_ARG0, 130 MSG_FIELD_MAX = 16 /* Max number of arguments */ 131 }; 132 133 enum dpfe_commands { 134 DPFE_CMD_GET_INFO, 135 DPFE_CMD_GET_REFRESH, 136 DPFE_CMD_GET_VENDOR, 137 DPFE_CMD_MAX /* Last entry */ 138 }; 139 140 /* 141 * Format of the binary firmware file: 142 * 143 * entry 144 * 0 header 145 * value: 0xfe0101fe <== little endian 146 * 0xfe1010fe <== big endian 147 * 1 sequence: 148 * [31:16] total segments on this build 149 * [15:0] this segment sequence. 150 * 2 FW version 151 * 3 IMEM byte size 152 * 4 DMEM byte size 153 * IMEM 154 * DMEM 155 * last checksum ==> sum of everything 156 */ 157 struct dpfe_firmware_header { 158 u32 magic; 159 u32 sequence; 160 u32 version; 161 u32 imem_size; 162 u32 dmem_size; 163 }; 164 165 /* Things we only need during initialization. */ 166 struct init_data { 167 unsigned int dmem_len; 168 unsigned int imem_len; 169 unsigned int chksum; 170 bool is_big_endian; 171 }; 172 173 /* API version and corresponding commands */ 174 struct dpfe_api { 175 int version; 176 const char *fw_name; 177 const struct attribute_group **sysfs_attrs; 178 u32 command[DPFE_CMD_MAX][MSG_FIELD_MAX]; 179 }; 180 181 /* Things we need for as long as we are active. */ 182 struct brcmstb_dpfe_priv { 183 void __iomem *regs; 184 void __iomem *dmem; 185 void __iomem *imem; 186 struct device *dev; 187 const struct dpfe_api *dpfe_api; 188 struct mutex lock; 189 }; 190 191 /* 192 * Forward declaration of our sysfs attribute functions, so we can declare the 193 * attribute data structures early. 194 */ 195 static ssize_t show_info(struct device *, struct device_attribute *, char *); 196 static ssize_t show_refresh(struct device *, struct device_attribute *, char *); 197 static ssize_t store_refresh(struct device *, struct device_attribute *, 198 const char *, size_t); 199 static ssize_t show_vendor(struct device *, struct device_attribute *, char *); 200 static ssize_t show_dram(struct device *, struct device_attribute *, char *); 201 202 /* 203 * Declare our attributes early, so they can be referenced in the API data 204 * structure. We need to do this, because the attributes depend on the API 205 * version. 206 */ 207 static DEVICE_ATTR(dpfe_info, 0444, show_info, NULL); 208 static DEVICE_ATTR(dpfe_refresh, 0644, show_refresh, store_refresh); 209 static DEVICE_ATTR(dpfe_vendor, 0444, show_vendor, NULL); 210 static DEVICE_ATTR(dpfe_dram, 0444, show_dram, NULL); 211 212 /* API v2 sysfs attributes */ 213 static struct attribute *dpfe_v2_attrs[] = { 214 &dev_attr_dpfe_info.attr, 215 &dev_attr_dpfe_refresh.attr, 216 &dev_attr_dpfe_vendor.attr, 217 NULL 218 }; 219 ATTRIBUTE_GROUPS(dpfe_v2); 220 221 /* API v3 sysfs attributes */ 222 static struct attribute *dpfe_v3_attrs[] = { 223 &dev_attr_dpfe_info.attr, 224 &dev_attr_dpfe_dram.attr, 225 NULL 226 }; 227 ATTRIBUTE_GROUPS(dpfe_v3); 228 229 /* 230 * Old API v2 firmware commands, as defined in the rev 0.61 specification, we 231 * use a version set to 1 to denote that it is not compatible with the new API 232 * v2 and onwards. 233 */ 234 static const struct dpfe_api dpfe_api_old_v2 = { 235 .version = 1, 236 .fw_name = "dpfe.bin", 237 .sysfs_attrs = dpfe_v2_groups, 238 .command = { 239 [DPFE_CMD_GET_INFO] = { 240 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 241 [MSG_COMMAND] = 1, 242 [MSG_ARG_COUNT] = 1, 243 [MSG_ARG0] = 1, 244 }, 245 [DPFE_CMD_GET_REFRESH] = { 246 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 247 [MSG_COMMAND] = 2, 248 [MSG_ARG_COUNT] = 1, 249 [MSG_ARG0] = 1, 250 }, 251 [DPFE_CMD_GET_VENDOR] = { 252 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 253 [MSG_COMMAND] = 2, 254 [MSG_ARG_COUNT] = 1, 255 [MSG_ARG0] = 2, 256 }, 257 } 258 }; 259 260 /* 261 * API v2 firmware commands, as defined in the rev 0.8 specification, named new 262 * v2 here 263 */ 264 static const struct dpfe_api dpfe_api_new_v2 = { 265 .version = 2, 266 .fw_name = NULL, /* We expect the firmware to have been downloaded! */ 267 .sysfs_attrs = dpfe_v2_groups, 268 .command = { 269 [DPFE_CMD_GET_INFO] = { 270 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 271 [MSG_COMMAND] = 0x101, 272 }, 273 [DPFE_CMD_GET_REFRESH] = { 274 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 275 [MSG_COMMAND] = 0x201, 276 }, 277 [DPFE_CMD_GET_VENDOR] = { 278 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 279 [MSG_COMMAND] = 0x202, 280 }, 281 } 282 }; 283 284 /* API v3 firmware commands */ 285 static const struct dpfe_api dpfe_api_v3 = { 286 .version = 3, 287 .fw_name = NULL, /* We expect the firmware to have been downloaded! */ 288 .sysfs_attrs = dpfe_v3_groups, 289 .command = { 290 [DPFE_CMD_GET_INFO] = { 291 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 292 [MSG_COMMAND] = 0x0101, 293 [MSG_ARG_COUNT] = 1, 294 [MSG_ARG0] = 1, 295 }, 296 [DPFE_CMD_GET_REFRESH] = { 297 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 298 [MSG_COMMAND] = 0x0202, 299 [MSG_ARG_COUNT] = 0, 300 }, 301 /* There's no GET_VENDOR command in API v3. */ 302 }, 303 }; 304 305 static const char *get_error_text(unsigned int i) 306 { 307 static const char * const error_text[] = { 308 "Success", "Header code incorrect", 309 "Unknown command or argument", "Incorrect checksum", 310 "Malformed command", "Timed out", "Unknown error", 311 }; 312 313 if (unlikely(i >= ARRAY_SIZE(error_text))) 314 i = ARRAY_SIZE(error_text) - 1; 315 316 return error_text[i]; 317 } 318 319 static bool is_dcpu_enabled(struct brcmstb_dpfe_priv *priv) 320 { 321 u32 val; 322 323 mutex_lock(&priv->lock); 324 val = readl_relaxed(priv->regs + REG_DCPU_RESET); 325 mutex_unlock(&priv->lock); 326 327 return !(val & DCPU_RESET_MASK); 328 } 329 330 static void __disable_dcpu(struct brcmstb_dpfe_priv *priv) 331 { 332 u32 val; 333 334 if (!is_dcpu_enabled(priv)) 335 return; 336 337 mutex_lock(&priv->lock); 338 339 /* Put DCPU in reset if it's running. */ 340 val = readl_relaxed(priv->regs + REG_DCPU_RESET); 341 val |= (1 << DCPU_RESET_SHIFT); 342 writel_relaxed(val, priv->regs + REG_DCPU_RESET); 343 344 mutex_unlock(&priv->lock); 345 } 346 347 static void __enable_dcpu(struct brcmstb_dpfe_priv *priv) 348 { 349 void __iomem *regs = priv->regs; 350 u32 val; 351 352 mutex_lock(&priv->lock); 353 354 /* Clear mailbox registers. */ 355 writel_relaxed(0, regs + REG_TO_DCPU_MBOX); 356 writel_relaxed(0, regs + REG_TO_HOST_MBOX); 357 358 /* Disable DCPU clock gating */ 359 val = readl_relaxed(regs + REG_DCPU_RESET); 360 val &= ~(1 << DCPU_CLK_DISABLE_SHIFT); 361 writel_relaxed(val, regs + REG_DCPU_RESET); 362 363 /* Take DCPU out of reset */ 364 val = readl_relaxed(regs + REG_DCPU_RESET); 365 val &= ~(1 << DCPU_RESET_SHIFT); 366 writel_relaxed(val, regs + REG_DCPU_RESET); 367 368 mutex_unlock(&priv->lock); 369 } 370 371 static unsigned int get_msg_chksum(const u32 msg[], unsigned int max) 372 { 373 unsigned int sum = 0; 374 unsigned int i; 375 376 /* Don't include the last field in the checksum. */ 377 for (i = 0; i < max; i++) 378 sum += msg[i]; 379 380 return sum; 381 } 382 383 static void __iomem *get_msg_ptr(struct brcmstb_dpfe_priv *priv, u32 response, 384 char *buf, ssize_t *size) 385 { 386 unsigned int msg_type; 387 unsigned int offset; 388 void __iomem *ptr = NULL; 389 390 /* There is no need to use this function for API v3 or later. */ 391 if (unlikely(priv->dpfe_api->version >= 3)) 392 return NULL; 393 394 msg_type = (response >> DRAM_MSG_TYPE_OFFSET) & DRAM_MSG_TYPE_MASK; 395 offset = (response >> DRAM_MSG_ADDR_OFFSET) & DRAM_MSG_ADDR_MASK; 396 397 /* 398 * msg_type == 1: the offset is relative to the message RAM 399 * msg_type == 0: the offset is relative to the data RAM (this is the 400 * previous way of passing data) 401 * msg_type is anything else: there's critical hardware problem 402 */ 403 switch (msg_type) { 404 case 1: 405 ptr = priv->regs + DCPU_MSG_RAM_START + offset; 406 break; 407 case 0: 408 ptr = priv->dmem + offset; 409 break; 410 default: 411 dev_emerg(priv->dev, "invalid message reply from DCPU: %#x\n", 412 response); 413 if (buf && size) 414 *size = sprintf(buf, 415 "FATAL: communication error with DCPU\n"); 416 } 417 418 return ptr; 419 } 420 421 static void __finalize_command(struct brcmstb_dpfe_priv *priv) 422 { 423 unsigned int release_mbox; 424 425 /* 426 * It depends on the API version which MBOX register we have to write to 427 * signal we are done. 428 */ 429 release_mbox = (priv->dpfe_api->version < 2) 430 ? REG_TO_HOST_MBOX : REG_TO_DCPU_MBOX; 431 writel_relaxed(0, priv->regs + release_mbox); 432 } 433 434 static int __send_command(struct brcmstb_dpfe_priv *priv, unsigned int cmd, 435 u32 result[]) 436 { 437 void __iomem *regs = priv->regs; 438 unsigned int i, chksum, chksum_idx; 439 const u32 *msg; 440 int ret = 0; 441 u32 resp; 442 443 if (cmd >= DPFE_CMD_MAX) 444 return -1; 445 446 msg = priv->dpfe_api->command[cmd]; 447 448 mutex_lock(&priv->lock); 449 450 /* Wait for DCPU to become ready */ 451 for (i = 0; i < DELAY_LOOP_MAX; i++) { 452 resp = readl_relaxed(regs + REG_TO_HOST_MBOX); 453 if (resp == 0) 454 break; 455 msleep(1); 456 } 457 if (resp != 0) { 458 mutex_unlock(&priv->lock); 459 return -ffs(DCPU_RET_ERR_TIMEDOUT); 460 } 461 462 /* Compute checksum over the message */ 463 chksum_idx = msg[MSG_ARG_COUNT] + MSG_ARG_COUNT + 1; 464 chksum = get_msg_chksum(msg, chksum_idx); 465 466 /* Write command and arguments to message area */ 467 for (i = 0; i < MSG_FIELD_MAX; i++) { 468 if (i == chksum_idx) 469 writel_relaxed(chksum, regs + DCPU_MSG_RAM(i)); 470 else 471 writel_relaxed(msg[i], regs + DCPU_MSG_RAM(i)); 472 } 473 474 /* Tell DCPU there is a command waiting */ 475 writel_relaxed(1, regs + REG_TO_DCPU_MBOX); 476 477 /* Wait for DCPU to process the command */ 478 for (i = 0; i < DELAY_LOOP_MAX; i++) { 479 /* Read response code */ 480 resp = readl_relaxed(regs + REG_TO_HOST_MBOX); 481 if (resp > 0) 482 break; 483 msleep(1); 484 } 485 486 if (i == DELAY_LOOP_MAX) { 487 resp = (DCPU_RET_ERR_TIMEDOUT & ~DCPU_RET_ERROR_BIT); 488 ret = -ffs(resp); 489 } else { 490 /* Read response data */ 491 for (i = 0; i < MSG_FIELD_MAX; i++) 492 result[i] = readl_relaxed(regs + DCPU_MSG_RAM(i)); 493 chksum_idx = result[MSG_ARG_COUNT] + MSG_ARG_COUNT + 1; 494 } 495 496 /* Tell DCPU we are done */ 497 __finalize_command(priv); 498 499 mutex_unlock(&priv->lock); 500 501 if (ret) 502 return ret; 503 504 /* Verify response */ 505 chksum = get_msg_chksum(result, chksum_idx); 506 if (chksum != result[chksum_idx]) 507 resp = DCPU_RET_ERR_CHKSUM; 508 509 if (resp != DCPU_RET_SUCCESS) { 510 resp &= ~DCPU_RET_ERROR_BIT; 511 ret = -ffs(resp); 512 } 513 514 return ret; 515 } 516 517 /* Ensure that the firmware file loaded meets all the requirements. */ 518 static int __verify_firmware(struct init_data *init, 519 const struct firmware *fw) 520 { 521 const struct dpfe_firmware_header *header = (void *)fw->data; 522 unsigned int dmem_size, imem_size, total_size; 523 bool is_big_endian = false; 524 const u32 *chksum_ptr; 525 526 if (header->magic == DPFE_BE_MAGIC) 527 is_big_endian = true; 528 else if (header->magic != DPFE_LE_MAGIC) 529 return ERR_INVALID_MAGIC; 530 531 if (is_big_endian) { 532 dmem_size = be32_to_cpu(header->dmem_size); 533 imem_size = be32_to_cpu(header->imem_size); 534 } else { 535 dmem_size = le32_to_cpu(header->dmem_size); 536 imem_size = le32_to_cpu(header->imem_size); 537 } 538 539 /* Data and instruction sections are 32 bit words. */ 540 if ((dmem_size % sizeof(u32)) != 0 || (imem_size % sizeof(u32)) != 0) 541 return ERR_INVALID_SIZE; 542 543 /* 544 * The header + the data section + the instruction section + the 545 * checksum must be equal to the total firmware size. 546 */ 547 total_size = dmem_size + imem_size + sizeof(*header) + 548 sizeof(*chksum_ptr); 549 if (total_size != fw->size) 550 return ERR_INVALID_SIZE; 551 552 /* The checksum comes at the very end. */ 553 chksum_ptr = (void *)fw->data + sizeof(*header) + dmem_size + imem_size; 554 555 init->is_big_endian = is_big_endian; 556 init->dmem_len = dmem_size; 557 init->imem_len = imem_size; 558 init->chksum = (is_big_endian) 559 ? be32_to_cpu(*chksum_ptr) : le32_to_cpu(*chksum_ptr); 560 561 return 0; 562 } 563 564 /* Verify checksum by reading back the firmware from co-processor RAM. */ 565 static int __verify_fw_checksum(struct init_data *init, 566 struct brcmstb_dpfe_priv *priv, 567 const struct dpfe_firmware_header *header, 568 u32 checksum) 569 { 570 u32 magic, sequence, version, sum; 571 u32 __iomem *dmem = priv->dmem; 572 u32 __iomem *imem = priv->imem; 573 unsigned int i; 574 575 if (init->is_big_endian) { 576 magic = be32_to_cpu(header->magic); 577 sequence = be32_to_cpu(header->sequence); 578 version = be32_to_cpu(header->version); 579 } else { 580 magic = le32_to_cpu(header->magic); 581 sequence = le32_to_cpu(header->sequence); 582 version = le32_to_cpu(header->version); 583 } 584 585 sum = magic + sequence + version + init->dmem_len + init->imem_len; 586 587 for (i = 0; i < init->dmem_len / sizeof(u32); i++) 588 sum += readl_relaxed(dmem + i); 589 590 for (i = 0; i < init->imem_len / sizeof(u32); i++) 591 sum += readl_relaxed(imem + i); 592 593 return (sum == checksum) ? 0 : -1; 594 } 595 596 static int __write_firmware(u32 __iomem *mem, const u32 *fw, 597 unsigned int size, bool is_big_endian) 598 { 599 unsigned int i; 600 601 /* Convert size to 32-bit words. */ 602 size /= sizeof(u32); 603 604 /* It is recommended to clear the firmware area first. */ 605 for (i = 0; i < size; i++) 606 writel_relaxed(0, mem + i); 607 608 /* Now copy it. */ 609 if (is_big_endian) { 610 for (i = 0; i < size; i++) 611 writel_relaxed(be32_to_cpu(fw[i]), mem + i); 612 } else { 613 for (i = 0; i < size; i++) 614 writel_relaxed(le32_to_cpu(fw[i]), mem + i); 615 } 616 617 return 0; 618 } 619 620 static int brcmstb_dpfe_download_firmware(struct brcmstb_dpfe_priv *priv) 621 { 622 const struct dpfe_firmware_header *header; 623 unsigned int dmem_size, imem_size; 624 struct device *dev = priv->dev; 625 bool is_big_endian = false; 626 const struct firmware *fw; 627 const u32 *dmem, *imem; 628 struct init_data init; 629 const void *fw_blob; 630 int ret; 631 632 /* 633 * Skip downloading the firmware if the DCPU is already running and 634 * responding to commands. 635 */ 636 if (is_dcpu_enabled(priv)) { 637 u32 response[MSG_FIELD_MAX]; 638 639 ret = __send_command(priv, DPFE_CMD_GET_INFO, response); 640 if (!ret) 641 return 0; 642 } 643 644 /* 645 * If the firmware filename is NULL it means the boot firmware has to 646 * download the DCPU firmware for us. If that didn't work, we have to 647 * bail, since downloading it ourselves wouldn't work either. 648 */ 649 if (!priv->dpfe_api->fw_name) 650 return -ENODEV; 651 652 ret = firmware_request_nowarn(&fw, priv->dpfe_api->fw_name, dev); 653 /* 654 * Defer the firmware download if the firmware file couldn't be found. 655 * The root file system may not be available yet. 656 */ 657 if (ret) 658 return (ret == -ENOENT) ? -EPROBE_DEFER : ret; 659 660 ret = __verify_firmware(&init, fw); 661 if (ret) { 662 ret = -EFAULT; 663 goto release_fw; 664 } 665 666 __disable_dcpu(priv); 667 668 is_big_endian = init.is_big_endian; 669 dmem_size = init.dmem_len; 670 imem_size = init.imem_len; 671 672 /* At the beginning of the firmware blob is a header. */ 673 header = (struct dpfe_firmware_header *)fw->data; 674 /* Void pointer to the beginning of the actual firmware. */ 675 fw_blob = fw->data + sizeof(*header); 676 /* IMEM comes right after the header. */ 677 imem = fw_blob; 678 /* DMEM follows after IMEM. */ 679 dmem = fw_blob + imem_size; 680 681 ret = __write_firmware(priv->dmem, dmem, dmem_size, is_big_endian); 682 if (ret) 683 goto release_fw; 684 ret = __write_firmware(priv->imem, imem, imem_size, is_big_endian); 685 if (ret) 686 goto release_fw; 687 688 ret = __verify_fw_checksum(&init, priv, header, init.chksum); 689 if (ret) 690 goto release_fw; 691 692 __enable_dcpu(priv); 693 694 release_fw: 695 release_firmware(fw); 696 return ret; 697 } 698 699 static ssize_t generic_show(unsigned int command, u32 response[], 700 struct brcmstb_dpfe_priv *priv, char *buf) 701 { 702 int ret; 703 704 if (!priv) 705 return sprintf(buf, "ERROR: driver private data not set\n"); 706 707 ret = __send_command(priv, command, response); 708 if (ret < 0) 709 return sprintf(buf, "ERROR: %s\n", get_error_text(-ret)); 710 711 return 0; 712 } 713 714 static ssize_t show_info(struct device *dev, struct device_attribute *devattr, 715 char *buf) 716 { 717 u32 response[MSG_FIELD_MAX]; 718 struct brcmstb_dpfe_priv *priv; 719 unsigned int info; 720 ssize_t ret; 721 722 priv = dev_get_drvdata(dev); 723 ret = generic_show(DPFE_CMD_GET_INFO, response, priv, buf); 724 if (ret) 725 return ret; 726 727 info = response[MSG_ARG0]; 728 729 return sprintf(buf, "%u.%u.%u.%u\n", 730 (info >> 24) & 0xff, 731 (info >> 16) & 0xff, 732 (info >> 8) & 0xff, 733 info & 0xff); 734 } 735 736 static ssize_t show_refresh(struct device *dev, 737 struct device_attribute *devattr, char *buf) 738 { 739 u32 response[MSG_FIELD_MAX]; 740 void __iomem *info; 741 struct brcmstb_dpfe_priv *priv; 742 u8 refresh, sr_abort, ppre, thermal_offs, tuf; 743 u32 mr4; 744 ssize_t ret; 745 746 priv = dev_get_drvdata(dev); 747 ret = generic_show(DPFE_CMD_GET_REFRESH, response, priv, buf); 748 if (ret) 749 return ret; 750 751 info = get_msg_ptr(priv, response[MSG_ARG0], buf, &ret); 752 if (!info) 753 return ret; 754 755 mr4 = (readl_relaxed(info + DRAM_INFO_MR4) >> DRAM_INFO_MR4_SHIFT) & 756 DRAM_INFO_MR4_MASK; 757 758 refresh = (mr4 >> DRAM_MR4_REFRESH) & DRAM_MR4_REFRESH_MASK; 759 sr_abort = (mr4 >> DRAM_MR4_SR_ABORT) & DRAM_MR4_SR_ABORT_MASK; 760 ppre = (mr4 >> DRAM_MR4_PPRE) & DRAM_MR4_PPRE_MASK; 761 thermal_offs = (mr4 >> DRAM_MR4_TH_OFFS) & DRAM_MR4_TH_OFFS_MASK; 762 tuf = (mr4 >> DRAM_MR4_TUF) & DRAM_MR4_TUF_MASK; 763 764 return sprintf(buf, "%#x %#x %#x %#x %#x %#x %#x\n", 765 readl_relaxed(info + DRAM_INFO_INTERVAL), 766 refresh, sr_abort, ppre, thermal_offs, tuf, 767 readl_relaxed(info + DRAM_INFO_ERROR)); 768 } 769 770 static ssize_t store_refresh(struct device *dev, struct device_attribute *attr, 771 const char *buf, size_t count) 772 { 773 u32 response[MSG_FIELD_MAX]; 774 struct brcmstb_dpfe_priv *priv; 775 void __iomem *info; 776 unsigned long val; 777 int ret; 778 779 if (kstrtoul(buf, 0, &val) < 0) 780 return -EINVAL; 781 782 priv = dev_get_drvdata(dev); 783 ret = __send_command(priv, DPFE_CMD_GET_REFRESH, response); 784 if (ret) 785 return ret; 786 787 info = get_msg_ptr(priv, response[MSG_ARG0], NULL, NULL); 788 if (!info) 789 return -EIO; 790 791 writel_relaxed(val, info + DRAM_INFO_INTERVAL); 792 793 return count; 794 } 795 796 static ssize_t show_vendor(struct device *dev, struct device_attribute *devattr, 797 char *buf) 798 { 799 u32 response[MSG_FIELD_MAX]; 800 struct brcmstb_dpfe_priv *priv; 801 void __iomem *info; 802 ssize_t ret; 803 u32 mr5, mr6, mr7, mr8, err; 804 805 priv = dev_get_drvdata(dev); 806 ret = generic_show(DPFE_CMD_GET_VENDOR, response, priv, buf); 807 if (ret) 808 return ret; 809 810 info = get_msg_ptr(priv, response[MSG_ARG0], buf, &ret); 811 if (!info) 812 return ret; 813 814 mr5 = (readl_relaxed(info + DRAM_VENDOR_MR5) >> DRAM_VENDOR_SHIFT) & 815 DRAM_VENDOR_MASK; 816 mr6 = (readl_relaxed(info + DRAM_VENDOR_MR6) >> DRAM_VENDOR_SHIFT) & 817 DRAM_VENDOR_MASK; 818 mr7 = (readl_relaxed(info + DRAM_VENDOR_MR7) >> DRAM_VENDOR_SHIFT) & 819 DRAM_VENDOR_MASK; 820 mr8 = (readl_relaxed(info + DRAM_VENDOR_MR8) >> DRAM_VENDOR_SHIFT) & 821 DRAM_VENDOR_MASK; 822 err = readl_relaxed(info + DRAM_VENDOR_ERROR) & DRAM_VENDOR_MASK; 823 824 return sprintf(buf, "%#x %#x %#x %#x %#x\n", mr5, mr6, mr7, mr8, err); 825 } 826 827 static ssize_t show_dram(struct device *dev, struct device_attribute *devattr, 828 char *buf) 829 { 830 u32 response[MSG_FIELD_MAX]; 831 struct brcmstb_dpfe_priv *priv; 832 ssize_t ret; 833 u32 mr4, mr5, mr6, mr7, mr8, err; 834 835 priv = dev_get_drvdata(dev); 836 ret = generic_show(DPFE_CMD_GET_REFRESH, response, priv, buf); 837 if (ret) 838 return ret; 839 840 mr4 = response[MSG_ARG0 + 0] & DRAM_INFO_MR4_MASK; 841 mr5 = response[MSG_ARG0 + 1] & DRAM_DDR_INFO_MASK; 842 mr6 = response[MSG_ARG0 + 2] & DRAM_DDR_INFO_MASK; 843 mr7 = response[MSG_ARG0 + 3] & DRAM_DDR_INFO_MASK; 844 mr8 = response[MSG_ARG0 + 4] & DRAM_DDR_INFO_MASK; 845 err = response[MSG_ARG0 + 5] & DRAM_DDR_INFO_MASK; 846 847 return sprintf(buf, "%#x %#x %#x %#x %#x %#x\n", mr4, mr5, mr6, mr7, 848 mr8, err); 849 } 850 851 static int brcmstb_dpfe_resume(struct platform_device *pdev) 852 { 853 struct brcmstb_dpfe_priv *priv = platform_get_drvdata(pdev); 854 855 return brcmstb_dpfe_download_firmware(priv); 856 } 857 858 static int brcmstb_dpfe_probe(struct platform_device *pdev) 859 { 860 struct device *dev = &pdev->dev; 861 struct brcmstb_dpfe_priv *priv; 862 int ret; 863 864 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 865 if (!priv) 866 return -ENOMEM; 867 868 priv->dev = dev; 869 870 mutex_init(&priv->lock); 871 platform_set_drvdata(pdev, priv); 872 873 priv->regs = devm_platform_ioremap_resource_byname(pdev, "dpfe-cpu"); 874 if (IS_ERR(priv->regs)) { 875 dev_err(dev, "couldn't map DCPU registers\n"); 876 return -ENODEV; 877 } 878 879 priv->dmem = devm_platform_ioremap_resource_byname(pdev, "dpfe-dmem"); 880 if (IS_ERR(priv->dmem)) { 881 dev_err(dev, "Couldn't map DCPU data memory\n"); 882 return -ENOENT; 883 } 884 885 priv->imem = devm_platform_ioremap_resource_byname(pdev, "dpfe-imem"); 886 if (IS_ERR(priv->imem)) { 887 dev_err(dev, "Couldn't map DCPU instruction memory\n"); 888 return -ENOENT; 889 } 890 891 priv->dpfe_api = of_device_get_match_data(dev); 892 if (unlikely(!priv->dpfe_api)) { 893 /* 894 * It should be impossible to end up here, but to be safe we 895 * check anyway. 896 */ 897 dev_err(dev, "Couldn't determine API\n"); 898 return -ENOENT; 899 } 900 901 ret = brcmstb_dpfe_download_firmware(priv); 902 if (ret) 903 return dev_err_probe(dev, ret, "Couldn't download firmware\n"); 904 905 ret = sysfs_create_groups(&pdev->dev.kobj, priv->dpfe_api->sysfs_attrs); 906 if (!ret) 907 dev_info(dev, "registered with API v%d.\n", 908 priv->dpfe_api->version); 909 910 return ret; 911 } 912 913 static int brcmstb_dpfe_remove(struct platform_device *pdev) 914 { 915 struct brcmstb_dpfe_priv *priv = dev_get_drvdata(&pdev->dev); 916 917 sysfs_remove_groups(&pdev->dev.kobj, priv->dpfe_api->sysfs_attrs); 918 919 return 0; 920 } 921 922 static const struct of_device_id brcmstb_dpfe_of_match[] = { 923 /* Use legacy API v2 for a select number of chips */ 924 { .compatible = "brcm,bcm7268-dpfe-cpu", .data = &dpfe_api_old_v2 }, 925 { .compatible = "brcm,bcm7271-dpfe-cpu", .data = &dpfe_api_old_v2 }, 926 { .compatible = "brcm,bcm7278-dpfe-cpu", .data = &dpfe_api_old_v2 }, 927 { .compatible = "brcm,bcm7211-dpfe-cpu", .data = &dpfe_api_new_v2 }, 928 /* API v3 is the default going forward */ 929 { .compatible = "brcm,dpfe-cpu", .data = &dpfe_api_v3 }, 930 {} 931 }; 932 MODULE_DEVICE_TABLE(of, brcmstb_dpfe_of_match); 933 934 static struct platform_driver brcmstb_dpfe_driver = { 935 .driver = { 936 .name = DRVNAME, 937 .of_match_table = brcmstb_dpfe_of_match, 938 }, 939 .probe = brcmstb_dpfe_probe, 940 .remove = brcmstb_dpfe_remove, 941 .resume = brcmstb_dpfe_resume, 942 }; 943 944 module_platform_driver(brcmstb_dpfe_driver); 945 946 MODULE_AUTHOR("Markus Mayer <mmayer@broadcom.com>"); 947 MODULE_DESCRIPTION("BRCMSTB DDR PHY Front End Driver"); 948 MODULE_LICENSE("GPL"); 949