1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * DDR PHY Front End (DPFE) driver for Broadcom set top box SoCs 4 * 5 * Copyright (c) 2017 Broadcom 6 */ 7 8 /* 9 * This driver provides access to the DPFE interface of Broadcom STB SoCs. 10 * The firmware running on the DCPU inside the DDR PHY can provide current 11 * information about the system's RAM, for instance the DRAM refresh rate. 12 * This can be used as an indirect indicator for the DRAM's temperature. 13 * Slower refresh rate means cooler RAM, higher refresh rate means hotter 14 * RAM. 15 * 16 * Throughout the driver, we use readl_relaxed() and writel_relaxed(), which 17 * already contain the appropriate le32_to_cpu()/cpu_to_le32() calls. 18 * 19 * Note regarding the loading of the firmware image: we use be32_to_cpu() 20 * and le_32_to_cpu(), so we can support the following four cases: 21 * - LE kernel + LE firmware image (the most common case) 22 * - LE kernel + BE firmware image 23 * - BE kernel + LE firmware image 24 * - BE kernel + BE firmware image 25 * 26 * The DPCU always runs in big endian mode. The firmware image, however, can 27 * be in either format. Also, communication between host CPU and DCPU is 28 * always in little endian. 29 */ 30 31 #include <linux/delay.h> 32 #include <linux/firmware.h> 33 #include <linux/io.h> 34 #include <linux/module.h> 35 #include <linux/of_address.h> 36 #include <linux/of_device.h> 37 #include <linux/platform_device.h> 38 39 #define DRVNAME "brcmstb-dpfe" 40 41 /* DCPU register offsets */ 42 #define REG_DCPU_RESET 0x0 43 #define REG_TO_DCPU_MBOX 0x10 44 #define REG_TO_HOST_MBOX 0x14 45 46 /* Macros to process offsets returned by the DCPU */ 47 #define DRAM_MSG_ADDR_OFFSET 0x0 48 #define DRAM_MSG_TYPE_OFFSET 0x1c 49 #define DRAM_MSG_ADDR_MASK ((1UL << DRAM_MSG_TYPE_OFFSET) - 1) 50 #define DRAM_MSG_TYPE_MASK ((1UL << \ 51 (BITS_PER_LONG - DRAM_MSG_TYPE_OFFSET)) - 1) 52 53 /* Message RAM */ 54 #define DCPU_MSG_RAM_START 0x100 55 #define DCPU_MSG_RAM(x) (DCPU_MSG_RAM_START + (x) * sizeof(u32)) 56 57 /* DRAM Info Offsets & Masks */ 58 #define DRAM_INFO_INTERVAL 0x0 59 #define DRAM_INFO_MR4 0x4 60 #define DRAM_INFO_ERROR 0x8 61 #define DRAM_INFO_MR4_MASK 0xff 62 #define DRAM_INFO_MR4_SHIFT 24 /* We need to look at byte 3 */ 63 64 /* DRAM MR4 Offsets & Masks */ 65 #define DRAM_MR4_REFRESH 0x0 /* Refresh rate */ 66 #define DRAM_MR4_SR_ABORT 0x3 /* Self Refresh Abort */ 67 #define DRAM_MR4_PPRE 0x4 /* Post-package repair entry/exit */ 68 #define DRAM_MR4_TH_OFFS 0x5 /* Thermal Offset; vendor specific */ 69 #define DRAM_MR4_TUF 0x7 /* Temperature Update Flag */ 70 71 #define DRAM_MR4_REFRESH_MASK 0x7 72 #define DRAM_MR4_SR_ABORT_MASK 0x1 73 #define DRAM_MR4_PPRE_MASK 0x1 74 #define DRAM_MR4_TH_OFFS_MASK 0x3 75 #define DRAM_MR4_TUF_MASK 0x1 76 77 /* DRAM Vendor Offsets & Masks (API v2) */ 78 #define DRAM_VENDOR_MR5 0x0 79 #define DRAM_VENDOR_MR6 0x4 80 #define DRAM_VENDOR_MR7 0x8 81 #define DRAM_VENDOR_MR8 0xc 82 #define DRAM_VENDOR_ERROR 0x10 83 #define DRAM_VENDOR_MASK 0xff 84 #define DRAM_VENDOR_SHIFT 24 /* We need to look at byte 3 */ 85 86 /* DRAM Information Offsets & Masks (API v3) */ 87 #define DRAM_DDR_INFO_MR4 0x0 88 #define DRAM_DDR_INFO_MR5 0x4 89 #define DRAM_DDR_INFO_MR6 0x8 90 #define DRAM_DDR_INFO_MR7 0xc 91 #define DRAM_DDR_INFO_MR8 0x10 92 #define DRAM_DDR_INFO_ERROR 0x14 93 #define DRAM_DDR_INFO_MASK 0xff 94 95 /* Reset register bits & masks */ 96 #define DCPU_RESET_SHIFT 0x0 97 #define DCPU_RESET_MASK 0x1 98 #define DCPU_CLK_DISABLE_SHIFT 0x2 99 100 /* DCPU return codes */ 101 #define DCPU_RET_ERROR_BIT BIT(31) 102 #define DCPU_RET_SUCCESS 0x1 103 #define DCPU_RET_ERR_HEADER (DCPU_RET_ERROR_BIT | BIT(0)) 104 #define DCPU_RET_ERR_INVAL (DCPU_RET_ERROR_BIT | BIT(1)) 105 #define DCPU_RET_ERR_CHKSUM (DCPU_RET_ERROR_BIT | BIT(2)) 106 #define DCPU_RET_ERR_COMMAND (DCPU_RET_ERROR_BIT | BIT(3)) 107 /* This error code is not firmware defined and only used in the driver. */ 108 #define DCPU_RET_ERR_TIMEDOUT (DCPU_RET_ERROR_BIT | BIT(4)) 109 110 /* Firmware magic */ 111 #define DPFE_BE_MAGIC 0xfe1010fe 112 #define DPFE_LE_MAGIC 0xfe0101fe 113 114 /* Error codes */ 115 #define ERR_INVALID_MAGIC -1 116 #define ERR_INVALID_SIZE -2 117 #define ERR_INVALID_CHKSUM -3 118 119 /* Message types */ 120 #define DPFE_MSG_TYPE_COMMAND 1 121 #define DPFE_MSG_TYPE_RESPONSE 2 122 123 #define DELAY_LOOP_MAX 1000 124 125 enum dpfe_msg_fields { 126 MSG_HEADER, 127 MSG_COMMAND, 128 MSG_ARG_COUNT, 129 MSG_ARG0, 130 MSG_FIELD_MAX = 16 /* Max number of arguments */ 131 }; 132 133 enum dpfe_commands { 134 DPFE_CMD_GET_INFO, 135 DPFE_CMD_GET_REFRESH, 136 DPFE_CMD_GET_VENDOR, 137 DPFE_CMD_MAX /* Last entry */ 138 }; 139 140 /* 141 * Format of the binary firmware file: 142 * 143 * entry 144 * 0 header 145 * value: 0xfe0101fe <== little endian 146 * 0xfe1010fe <== big endian 147 * 1 sequence: 148 * [31:16] total segments on this build 149 * [15:0] this segment sequence. 150 * 2 FW version 151 * 3 IMEM byte size 152 * 4 DMEM byte size 153 * IMEM 154 * DMEM 155 * last checksum ==> sum of everything 156 */ 157 struct dpfe_firmware_header { 158 u32 magic; 159 u32 sequence; 160 u32 version; 161 u32 imem_size; 162 u32 dmem_size; 163 }; 164 165 /* Things we only need during initialization. */ 166 struct init_data { 167 unsigned int dmem_len; 168 unsigned int imem_len; 169 unsigned int chksum; 170 bool is_big_endian; 171 }; 172 173 /* API version and corresponding commands */ 174 struct dpfe_api { 175 int version; 176 const char *fw_name; 177 const struct attribute_group **sysfs_attrs; 178 u32 command[DPFE_CMD_MAX][MSG_FIELD_MAX]; 179 }; 180 181 /* Things we need for as long as we are active. */ 182 struct brcmstb_dpfe_priv { 183 void __iomem *regs; 184 void __iomem *dmem; 185 void __iomem *imem; 186 struct device *dev; 187 const struct dpfe_api *dpfe_api; 188 struct mutex lock; 189 }; 190 191 /* 192 * Forward declaration of our sysfs attribute functions, so we can declare the 193 * attribute data structures early. 194 */ 195 static ssize_t show_info(struct device *, struct device_attribute *, char *); 196 static ssize_t show_refresh(struct device *, struct device_attribute *, char *); 197 static ssize_t store_refresh(struct device *, struct device_attribute *, 198 const char *, size_t); 199 static ssize_t show_vendor(struct device *, struct device_attribute *, char *); 200 static ssize_t show_dram(struct device *, struct device_attribute *, char *); 201 202 /* 203 * Declare our attributes early, so they can be referenced in the API data 204 * structure. We need to do this, because the attributes depend on the API 205 * version. 206 */ 207 static DEVICE_ATTR(dpfe_info, 0444, show_info, NULL); 208 static DEVICE_ATTR(dpfe_refresh, 0644, show_refresh, store_refresh); 209 static DEVICE_ATTR(dpfe_vendor, 0444, show_vendor, NULL); 210 static DEVICE_ATTR(dpfe_dram, 0444, show_dram, NULL); 211 212 /* API v2 sysfs attributes */ 213 static struct attribute *dpfe_v2_attrs[] = { 214 &dev_attr_dpfe_info.attr, 215 &dev_attr_dpfe_refresh.attr, 216 &dev_attr_dpfe_vendor.attr, 217 NULL 218 }; 219 ATTRIBUTE_GROUPS(dpfe_v2); 220 221 /* API v3 sysfs attributes */ 222 static struct attribute *dpfe_v3_attrs[] = { 223 &dev_attr_dpfe_info.attr, 224 &dev_attr_dpfe_dram.attr, 225 NULL 226 }; 227 ATTRIBUTE_GROUPS(dpfe_v3); 228 229 /* 230 * Old API v2 firmware commands, as defined in the rev 0.61 specification, we 231 * use a version set to 1 to denote that it is not compatible with the new API 232 * v2 and onwards. 233 */ 234 static const struct dpfe_api dpfe_api_old_v2 = { 235 .version = 1, 236 .fw_name = "dpfe.bin", 237 .sysfs_attrs = dpfe_v2_groups, 238 .command = { 239 [DPFE_CMD_GET_INFO] = { 240 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 241 [MSG_COMMAND] = 1, 242 [MSG_ARG_COUNT] = 1, 243 [MSG_ARG0] = 1, 244 }, 245 [DPFE_CMD_GET_REFRESH] = { 246 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 247 [MSG_COMMAND] = 2, 248 [MSG_ARG_COUNT] = 1, 249 [MSG_ARG0] = 1, 250 }, 251 [DPFE_CMD_GET_VENDOR] = { 252 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 253 [MSG_COMMAND] = 2, 254 [MSG_ARG_COUNT] = 1, 255 [MSG_ARG0] = 2, 256 }, 257 } 258 }; 259 260 /* 261 * API v2 firmware commands, as defined in the rev 0.8 specification, named new 262 * v2 here 263 */ 264 static const struct dpfe_api dpfe_api_new_v2 = { 265 .version = 2, 266 .fw_name = NULL, /* We expect the firmware to have been downloaded! */ 267 .sysfs_attrs = dpfe_v2_groups, 268 .command = { 269 [DPFE_CMD_GET_INFO] = { 270 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 271 [MSG_COMMAND] = 0x101, 272 }, 273 [DPFE_CMD_GET_REFRESH] = { 274 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 275 [MSG_COMMAND] = 0x201, 276 }, 277 [DPFE_CMD_GET_VENDOR] = { 278 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 279 [MSG_COMMAND] = 0x202, 280 }, 281 } 282 }; 283 284 /* API v3 firmware commands */ 285 static const struct dpfe_api dpfe_api_v3 = { 286 .version = 3, 287 .fw_name = NULL, /* We expect the firmware to have been downloaded! */ 288 .sysfs_attrs = dpfe_v3_groups, 289 .command = { 290 [DPFE_CMD_GET_INFO] = { 291 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 292 [MSG_COMMAND] = 0x0101, 293 [MSG_ARG_COUNT] = 1, 294 [MSG_ARG0] = 1, 295 }, 296 [DPFE_CMD_GET_REFRESH] = { 297 [MSG_HEADER] = DPFE_MSG_TYPE_COMMAND, 298 [MSG_COMMAND] = 0x0202, 299 [MSG_ARG_COUNT] = 0, 300 }, 301 /* There's no GET_VENDOR command in API v3. */ 302 }, 303 }; 304 305 static const char *get_error_text(unsigned int i) 306 { 307 static const char * const error_text[] = { 308 "Success", "Header code incorrect", 309 "Unknown command or argument", "Incorrect checksum", 310 "Malformed command", "Timed out", "Unknown error", 311 }; 312 313 if (unlikely(i >= ARRAY_SIZE(error_text))) 314 i = ARRAY_SIZE(error_text) - 1; 315 316 return error_text[i]; 317 } 318 319 static bool is_dcpu_enabled(struct brcmstb_dpfe_priv *priv) 320 { 321 u32 val; 322 323 mutex_lock(&priv->lock); 324 val = readl_relaxed(priv->regs + REG_DCPU_RESET); 325 mutex_unlock(&priv->lock); 326 327 return !(val & DCPU_RESET_MASK); 328 } 329 330 static void __disable_dcpu(struct brcmstb_dpfe_priv *priv) 331 { 332 u32 val; 333 334 if (!is_dcpu_enabled(priv)) 335 return; 336 337 mutex_lock(&priv->lock); 338 339 /* Put DCPU in reset if it's running. */ 340 val = readl_relaxed(priv->regs + REG_DCPU_RESET); 341 val |= (1 << DCPU_RESET_SHIFT); 342 writel_relaxed(val, priv->regs + REG_DCPU_RESET); 343 344 mutex_unlock(&priv->lock); 345 } 346 347 static void __enable_dcpu(struct brcmstb_dpfe_priv *priv) 348 { 349 void __iomem *regs = priv->regs; 350 u32 val; 351 352 mutex_lock(&priv->lock); 353 354 /* Clear mailbox registers. */ 355 writel_relaxed(0, regs + REG_TO_DCPU_MBOX); 356 writel_relaxed(0, regs + REG_TO_HOST_MBOX); 357 358 /* Disable DCPU clock gating */ 359 val = readl_relaxed(regs + REG_DCPU_RESET); 360 val &= ~(1 << DCPU_CLK_DISABLE_SHIFT); 361 writel_relaxed(val, regs + REG_DCPU_RESET); 362 363 /* Take DCPU out of reset */ 364 val = readl_relaxed(regs + REG_DCPU_RESET); 365 val &= ~(1 << DCPU_RESET_SHIFT); 366 writel_relaxed(val, regs + REG_DCPU_RESET); 367 368 mutex_unlock(&priv->lock); 369 } 370 371 static unsigned int get_msg_chksum(const u32 msg[], unsigned int max) 372 { 373 unsigned int sum = 0; 374 unsigned int i; 375 376 /* Don't include the last field in the checksum. */ 377 for (i = 0; i < max; i++) 378 sum += msg[i]; 379 380 return sum; 381 } 382 383 static void __iomem *get_msg_ptr(struct brcmstb_dpfe_priv *priv, u32 response, 384 char *buf, ssize_t *size) 385 { 386 unsigned int msg_type; 387 unsigned int offset; 388 void __iomem *ptr = NULL; 389 390 /* There is no need to use this function for API v3 or later. */ 391 if (unlikely(priv->dpfe_api->version >= 3)) 392 return NULL; 393 394 msg_type = (response >> DRAM_MSG_TYPE_OFFSET) & DRAM_MSG_TYPE_MASK; 395 offset = (response >> DRAM_MSG_ADDR_OFFSET) & DRAM_MSG_ADDR_MASK; 396 397 /* 398 * msg_type == 1: the offset is relative to the message RAM 399 * msg_type == 0: the offset is relative to the data RAM (this is the 400 * previous way of passing data) 401 * msg_type is anything else: there's critical hardware problem 402 */ 403 switch (msg_type) { 404 case 1: 405 ptr = priv->regs + DCPU_MSG_RAM_START + offset; 406 break; 407 case 0: 408 ptr = priv->dmem + offset; 409 break; 410 default: 411 dev_emerg(priv->dev, "invalid message reply from DCPU: %#x\n", 412 response); 413 if (buf && size) 414 *size = sprintf(buf, 415 "FATAL: communication error with DCPU\n"); 416 } 417 418 return ptr; 419 } 420 421 static void __finalize_command(struct brcmstb_dpfe_priv *priv) 422 { 423 unsigned int release_mbox; 424 425 /* 426 * It depends on the API version which MBOX register we have to write to 427 * to signal we are done. 428 */ 429 release_mbox = (priv->dpfe_api->version < 2) 430 ? REG_TO_HOST_MBOX : REG_TO_DCPU_MBOX; 431 writel_relaxed(0, priv->regs + release_mbox); 432 } 433 434 static int __send_command(struct brcmstb_dpfe_priv *priv, unsigned int cmd, 435 u32 result[]) 436 { 437 const u32 *msg = priv->dpfe_api->command[cmd]; 438 void __iomem *regs = priv->regs; 439 unsigned int i, chksum, chksum_idx; 440 int ret = 0; 441 u32 resp; 442 443 if (cmd >= DPFE_CMD_MAX) 444 return -1; 445 446 mutex_lock(&priv->lock); 447 448 /* Wait for DCPU to become ready */ 449 for (i = 0; i < DELAY_LOOP_MAX; i++) { 450 resp = readl_relaxed(regs + REG_TO_HOST_MBOX); 451 if (resp == 0) 452 break; 453 msleep(1); 454 } 455 if (resp != 0) { 456 mutex_unlock(&priv->lock); 457 return -ffs(DCPU_RET_ERR_TIMEDOUT); 458 } 459 460 /* Compute checksum over the message */ 461 chksum_idx = msg[MSG_ARG_COUNT] + MSG_ARG_COUNT + 1; 462 chksum = get_msg_chksum(msg, chksum_idx); 463 464 /* Write command and arguments to message area */ 465 for (i = 0; i < MSG_FIELD_MAX; i++) { 466 if (i == chksum_idx) 467 writel_relaxed(chksum, regs + DCPU_MSG_RAM(i)); 468 else 469 writel_relaxed(msg[i], regs + DCPU_MSG_RAM(i)); 470 } 471 472 /* Tell DCPU there is a command waiting */ 473 writel_relaxed(1, regs + REG_TO_DCPU_MBOX); 474 475 /* Wait for DCPU to process the command */ 476 for (i = 0; i < DELAY_LOOP_MAX; i++) { 477 /* Read response code */ 478 resp = readl_relaxed(regs + REG_TO_HOST_MBOX); 479 if (resp > 0) 480 break; 481 msleep(1); 482 } 483 484 if (i == DELAY_LOOP_MAX) { 485 resp = (DCPU_RET_ERR_TIMEDOUT & ~DCPU_RET_ERROR_BIT); 486 ret = -ffs(resp); 487 } else { 488 /* Read response data */ 489 for (i = 0; i < MSG_FIELD_MAX; i++) 490 result[i] = readl_relaxed(regs + DCPU_MSG_RAM(i)); 491 chksum_idx = result[MSG_ARG_COUNT] + MSG_ARG_COUNT + 1; 492 } 493 494 /* Tell DCPU we are done */ 495 __finalize_command(priv); 496 497 mutex_unlock(&priv->lock); 498 499 if (ret) 500 return ret; 501 502 /* Verify response */ 503 chksum = get_msg_chksum(result, chksum_idx); 504 if (chksum != result[chksum_idx]) 505 resp = DCPU_RET_ERR_CHKSUM; 506 507 if (resp != DCPU_RET_SUCCESS) { 508 resp &= ~DCPU_RET_ERROR_BIT; 509 ret = -ffs(resp); 510 } 511 512 return ret; 513 } 514 515 /* Ensure that the firmware file loaded meets all the requirements. */ 516 static int __verify_firmware(struct init_data *init, 517 const struct firmware *fw) 518 { 519 const struct dpfe_firmware_header *header = (void *)fw->data; 520 unsigned int dmem_size, imem_size, total_size; 521 bool is_big_endian = false; 522 const u32 *chksum_ptr; 523 524 if (header->magic == DPFE_BE_MAGIC) 525 is_big_endian = true; 526 else if (header->magic != DPFE_LE_MAGIC) 527 return ERR_INVALID_MAGIC; 528 529 if (is_big_endian) { 530 dmem_size = be32_to_cpu(header->dmem_size); 531 imem_size = be32_to_cpu(header->imem_size); 532 } else { 533 dmem_size = le32_to_cpu(header->dmem_size); 534 imem_size = le32_to_cpu(header->imem_size); 535 } 536 537 /* Data and instruction sections are 32 bit words. */ 538 if ((dmem_size % sizeof(u32)) != 0 || (imem_size % sizeof(u32)) != 0) 539 return ERR_INVALID_SIZE; 540 541 /* 542 * The header + the data section + the instruction section + the 543 * checksum must be equal to the total firmware size. 544 */ 545 total_size = dmem_size + imem_size + sizeof(*header) + 546 sizeof(*chksum_ptr); 547 if (total_size != fw->size) 548 return ERR_INVALID_SIZE; 549 550 /* The checksum comes at the very end. */ 551 chksum_ptr = (void *)fw->data + sizeof(*header) + dmem_size + imem_size; 552 553 init->is_big_endian = is_big_endian; 554 init->dmem_len = dmem_size; 555 init->imem_len = imem_size; 556 init->chksum = (is_big_endian) 557 ? be32_to_cpu(*chksum_ptr) : le32_to_cpu(*chksum_ptr); 558 559 return 0; 560 } 561 562 /* Verify checksum by reading back the firmware from co-processor RAM. */ 563 static int __verify_fw_checksum(struct init_data *init, 564 struct brcmstb_dpfe_priv *priv, 565 const struct dpfe_firmware_header *header, 566 u32 checksum) 567 { 568 u32 magic, sequence, version, sum; 569 u32 __iomem *dmem = priv->dmem; 570 u32 __iomem *imem = priv->imem; 571 unsigned int i; 572 573 if (init->is_big_endian) { 574 magic = be32_to_cpu(header->magic); 575 sequence = be32_to_cpu(header->sequence); 576 version = be32_to_cpu(header->version); 577 } else { 578 magic = le32_to_cpu(header->magic); 579 sequence = le32_to_cpu(header->sequence); 580 version = le32_to_cpu(header->version); 581 } 582 583 sum = magic + sequence + version + init->dmem_len + init->imem_len; 584 585 for (i = 0; i < init->dmem_len / sizeof(u32); i++) 586 sum += readl_relaxed(dmem + i); 587 588 for (i = 0; i < init->imem_len / sizeof(u32); i++) 589 sum += readl_relaxed(imem + i); 590 591 return (sum == checksum) ? 0 : -1; 592 } 593 594 static int __write_firmware(u32 __iomem *mem, const u32 *fw, 595 unsigned int size, bool is_big_endian) 596 { 597 unsigned int i; 598 599 /* Convert size to 32-bit words. */ 600 size /= sizeof(u32); 601 602 /* It is recommended to clear the firmware area first. */ 603 for (i = 0; i < size; i++) 604 writel_relaxed(0, mem + i); 605 606 /* Now copy it. */ 607 if (is_big_endian) { 608 for (i = 0; i < size; i++) 609 writel_relaxed(be32_to_cpu(fw[i]), mem + i); 610 } else { 611 for (i = 0; i < size; i++) 612 writel_relaxed(le32_to_cpu(fw[i]), mem + i); 613 } 614 615 return 0; 616 } 617 618 static int brcmstb_dpfe_download_firmware(struct brcmstb_dpfe_priv *priv) 619 { 620 const struct dpfe_firmware_header *header; 621 unsigned int dmem_size, imem_size; 622 struct device *dev = priv->dev; 623 bool is_big_endian = false; 624 const struct firmware *fw; 625 const u32 *dmem, *imem; 626 struct init_data init; 627 const void *fw_blob; 628 int ret; 629 630 /* 631 * Skip downloading the firmware if the DCPU is already running and 632 * responding to commands. 633 */ 634 if (is_dcpu_enabled(priv)) { 635 u32 response[MSG_FIELD_MAX]; 636 637 ret = __send_command(priv, DPFE_CMD_GET_INFO, response); 638 if (!ret) 639 return 0; 640 } 641 642 /* 643 * If the firmware filename is NULL it means the boot firmware has to 644 * download the DCPU firmware for us. If that didn't work, we have to 645 * bail, since downloading it ourselves wouldn't work either. 646 */ 647 if (!priv->dpfe_api->fw_name) 648 return -ENODEV; 649 650 ret = firmware_request_nowarn(&fw, priv->dpfe_api->fw_name, dev); 651 /* 652 * Defer the firmware download if the firmware file couldn't be found. 653 * The root file system may not be available yet. 654 */ 655 if (ret) 656 return (ret == -ENOENT) ? -EPROBE_DEFER : ret; 657 658 ret = __verify_firmware(&init, fw); 659 if (ret) { 660 ret = -EFAULT; 661 goto release_fw; 662 } 663 664 __disable_dcpu(priv); 665 666 is_big_endian = init.is_big_endian; 667 dmem_size = init.dmem_len; 668 imem_size = init.imem_len; 669 670 /* At the beginning of the firmware blob is a header. */ 671 header = (struct dpfe_firmware_header *)fw->data; 672 /* Void pointer to the beginning of the actual firmware. */ 673 fw_blob = fw->data + sizeof(*header); 674 /* IMEM comes right after the header. */ 675 imem = fw_blob; 676 /* DMEM follows after IMEM. */ 677 dmem = fw_blob + imem_size; 678 679 ret = __write_firmware(priv->dmem, dmem, dmem_size, is_big_endian); 680 if (ret) 681 goto release_fw; 682 ret = __write_firmware(priv->imem, imem, imem_size, is_big_endian); 683 if (ret) 684 goto release_fw; 685 686 ret = __verify_fw_checksum(&init, priv, header, init.chksum); 687 if (ret) 688 goto release_fw; 689 690 __enable_dcpu(priv); 691 692 release_fw: 693 release_firmware(fw); 694 return ret; 695 } 696 697 static ssize_t generic_show(unsigned int command, u32 response[], 698 struct brcmstb_dpfe_priv *priv, char *buf) 699 { 700 int ret; 701 702 if (!priv) 703 return sprintf(buf, "ERROR: driver private data not set\n"); 704 705 ret = __send_command(priv, command, response); 706 if (ret < 0) 707 return sprintf(buf, "ERROR: %s\n", get_error_text(-ret)); 708 709 return 0; 710 } 711 712 static ssize_t show_info(struct device *dev, struct device_attribute *devattr, 713 char *buf) 714 { 715 u32 response[MSG_FIELD_MAX]; 716 struct brcmstb_dpfe_priv *priv; 717 unsigned int info; 718 ssize_t ret; 719 720 priv = dev_get_drvdata(dev); 721 ret = generic_show(DPFE_CMD_GET_INFO, response, priv, buf); 722 if (ret) 723 return ret; 724 725 info = response[MSG_ARG0]; 726 727 return sprintf(buf, "%u.%u.%u.%u\n", 728 (info >> 24) & 0xff, 729 (info >> 16) & 0xff, 730 (info >> 8) & 0xff, 731 info & 0xff); 732 } 733 734 static ssize_t show_refresh(struct device *dev, 735 struct device_attribute *devattr, char *buf) 736 { 737 u32 response[MSG_FIELD_MAX]; 738 void __iomem *info; 739 struct brcmstb_dpfe_priv *priv; 740 u8 refresh, sr_abort, ppre, thermal_offs, tuf; 741 u32 mr4; 742 ssize_t ret; 743 744 priv = dev_get_drvdata(dev); 745 ret = generic_show(DPFE_CMD_GET_REFRESH, response, priv, buf); 746 if (ret) 747 return ret; 748 749 info = get_msg_ptr(priv, response[MSG_ARG0], buf, &ret); 750 if (!info) 751 return ret; 752 753 mr4 = (readl_relaxed(info + DRAM_INFO_MR4) >> DRAM_INFO_MR4_SHIFT) & 754 DRAM_INFO_MR4_MASK; 755 756 refresh = (mr4 >> DRAM_MR4_REFRESH) & DRAM_MR4_REFRESH_MASK; 757 sr_abort = (mr4 >> DRAM_MR4_SR_ABORT) & DRAM_MR4_SR_ABORT_MASK; 758 ppre = (mr4 >> DRAM_MR4_PPRE) & DRAM_MR4_PPRE_MASK; 759 thermal_offs = (mr4 >> DRAM_MR4_TH_OFFS) & DRAM_MR4_TH_OFFS_MASK; 760 tuf = (mr4 >> DRAM_MR4_TUF) & DRAM_MR4_TUF_MASK; 761 762 return sprintf(buf, "%#x %#x %#x %#x %#x %#x %#x\n", 763 readl_relaxed(info + DRAM_INFO_INTERVAL), 764 refresh, sr_abort, ppre, thermal_offs, tuf, 765 readl_relaxed(info + DRAM_INFO_ERROR)); 766 } 767 768 static ssize_t store_refresh(struct device *dev, struct device_attribute *attr, 769 const char *buf, size_t count) 770 { 771 u32 response[MSG_FIELD_MAX]; 772 struct brcmstb_dpfe_priv *priv; 773 void __iomem *info; 774 unsigned long val; 775 int ret; 776 777 if (kstrtoul(buf, 0, &val) < 0) 778 return -EINVAL; 779 780 priv = dev_get_drvdata(dev); 781 ret = __send_command(priv, DPFE_CMD_GET_REFRESH, response); 782 if (ret) 783 return ret; 784 785 info = get_msg_ptr(priv, response[MSG_ARG0], NULL, NULL); 786 if (!info) 787 return -EIO; 788 789 writel_relaxed(val, info + DRAM_INFO_INTERVAL); 790 791 return count; 792 } 793 794 static ssize_t show_vendor(struct device *dev, struct device_attribute *devattr, 795 char *buf) 796 { 797 u32 response[MSG_FIELD_MAX]; 798 struct brcmstb_dpfe_priv *priv; 799 void __iomem *info; 800 ssize_t ret; 801 u32 mr5, mr6, mr7, mr8, err; 802 803 priv = dev_get_drvdata(dev); 804 ret = generic_show(DPFE_CMD_GET_VENDOR, response, priv, buf); 805 if (ret) 806 return ret; 807 808 info = get_msg_ptr(priv, response[MSG_ARG0], buf, &ret); 809 if (!info) 810 return ret; 811 812 mr5 = (readl_relaxed(info + DRAM_VENDOR_MR5) >> DRAM_VENDOR_SHIFT) & 813 DRAM_VENDOR_MASK; 814 mr6 = (readl_relaxed(info + DRAM_VENDOR_MR6) >> DRAM_VENDOR_SHIFT) & 815 DRAM_VENDOR_MASK; 816 mr7 = (readl_relaxed(info + DRAM_VENDOR_MR7) >> DRAM_VENDOR_SHIFT) & 817 DRAM_VENDOR_MASK; 818 mr8 = (readl_relaxed(info + DRAM_VENDOR_MR8) >> DRAM_VENDOR_SHIFT) & 819 DRAM_VENDOR_MASK; 820 err = readl_relaxed(info + DRAM_VENDOR_ERROR) & DRAM_VENDOR_MASK; 821 822 return sprintf(buf, "%#x %#x %#x %#x %#x\n", mr5, mr6, mr7, mr8, err); 823 } 824 825 static ssize_t show_dram(struct device *dev, struct device_attribute *devattr, 826 char *buf) 827 { 828 u32 response[MSG_FIELD_MAX]; 829 struct brcmstb_dpfe_priv *priv; 830 ssize_t ret; 831 u32 mr4, mr5, mr6, mr7, mr8, err; 832 833 priv = dev_get_drvdata(dev); 834 ret = generic_show(DPFE_CMD_GET_REFRESH, response, priv, buf); 835 if (ret) 836 return ret; 837 838 mr4 = response[MSG_ARG0 + 0] & DRAM_INFO_MR4_MASK; 839 mr5 = response[MSG_ARG0 + 1] & DRAM_DDR_INFO_MASK; 840 mr6 = response[MSG_ARG0 + 2] & DRAM_DDR_INFO_MASK; 841 mr7 = response[MSG_ARG0 + 3] & DRAM_DDR_INFO_MASK; 842 mr8 = response[MSG_ARG0 + 4] & DRAM_DDR_INFO_MASK; 843 err = response[MSG_ARG0 + 5] & DRAM_DDR_INFO_MASK; 844 845 return sprintf(buf, "%#x %#x %#x %#x %#x %#x\n", mr4, mr5, mr6, mr7, 846 mr8, err); 847 } 848 849 static int brcmstb_dpfe_resume(struct platform_device *pdev) 850 { 851 struct brcmstb_dpfe_priv *priv = platform_get_drvdata(pdev); 852 853 return brcmstb_dpfe_download_firmware(priv); 854 } 855 856 static int brcmstb_dpfe_probe(struct platform_device *pdev) 857 { 858 struct device *dev = &pdev->dev; 859 struct brcmstb_dpfe_priv *priv; 860 struct resource *res; 861 int ret; 862 863 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 864 if (!priv) 865 return -ENOMEM; 866 867 priv->dev = dev; 868 869 mutex_init(&priv->lock); 870 platform_set_drvdata(pdev, priv); 871 872 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dpfe-cpu"); 873 priv->regs = devm_ioremap_resource(dev, res); 874 if (IS_ERR(priv->regs)) { 875 dev_err(dev, "couldn't map DCPU registers\n"); 876 return -ENODEV; 877 } 878 879 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dpfe-dmem"); 880 priv->dmem = devm_ioremap_resource(dev, res); 881 if (IS_ERR(priv->dmem)) { 882 dev_err(dev, "Couldn't map DCPU data memory\n"); 883 return -ENOENT; 884 } 885 886 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dpfe-imem"); 887 priv->imem = devm_ioremap_resource(dev, res); 888 if (IS_ERR(priv->imem)) { 889 dev_err(dev, "Couldn't map DCPU instruction memory\n"); 890 return -ENOENT; 891 } 892 893 priv->dpfe_api = of_device_get_match_data(dev); 894 if (unlikely(!priv->dpfe_api)) { 895 /* 896 * It should be impossible to end up here, but to be safe we 897 * check anyway. 898 */ 899 dev_err(dev, "Couldn't determine API\n"); 900 return -ENOENT; 901 } 902 903 ret = brcmstb_dpfe_download_firmware(priv); 904 if (ret) 905 return dev_err_probe(dev, ret, "Couldn't download firmware\n"); 906 907 ret = sysfs_create_groups(&pdev->dev.kobj, priv->dpfe_api->sysfs_attrs); 908 if (!ret) 909 dev_info(dev, "registered with API v%d.\n", 910 priv->dpfe_api->version); 911 912 return ret; 913 } 914 915 static int brcmstb_dpfe_remove(struct platform_device *pdev) 916 { 917 struct brcmstb_dpfe_priv *priv = dev_get_drvdata(&pdev->dev); 918 919 sysfs_remove_groups(&pdev->dev.kobj, priv->dpfe_api->sysfs_attrs); 920 921 return 0; 922 } 923 924 static const struct of_device_id brcmstb_dpfe_of_match[] = { 925 /* Use legacy API v2 for a select number of chips */ 926 { .compatible = "brcm,bcm7268-dpfe-cpu", .data = &dpfe_api_old_v2 }, 927 { .compatible = "brcm,bcm7271-dpfe-cpu", .data = &dpfe_api_old_v2 }, 928 { .compatible = "brcm,bcm7278-dpfe-cpu", .data = &dpfe_api_old_v2 }, 929 { .compatible = "brcm,bcm7211-dpfe-cpu", .data = &dpfe_api_new_v2 }, 930 /* API v3 is the default going forward */ 931 { .compatible = "brcm,dpfe-cpu", .data = &dpfe_api_v3 }, 932 {} 933 }; 934 MODULE_DEVICE_TABLE(of, brcmstb_dpfe_of_match); 935 936 static struct platform_driver brcmstb_dpfe_driver = { 937 .driver = { 938 .name = DRVNAME, 939 .of_match_table = brcmstb_dpfe_of_match, 940 }, 941 .probe = brcmstb_dpfe_probe, 942 .remove = brcmstb_dpfe_remove, 943 .resume = brcmstb_dpfe_resume, 944 }; 945 946 module_platform_driver(brcmstb_dpfe_driver); 947 948 MODULE_AUTHOR("Markus Mayer <mmayer@broadcom.com>"); 949 MODULE_DESCRIPTION("BRCMSTB DDR PHY Front End Driver"); 950 MODULE_LICENSE("GPL"); 951