1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 *
4 * Copyright (C) 2005 Mike Isely <isely@pobox.com>
5 * Copyright (C) 2004 Aurelien Alleaume <slts@free.fr>
6 */
7
8 #include <linux/device.h> // for linux/firmware.h
9 #include <linux/firmware.h>
10 #include "pvrusb2-util.h"
11 #include "pvrusb2-encoder.h"
12 #include "pvrusb2-hdw-internal.h"
13 #include "pvrusb2-debug.h"
14 #include "pvrusb2-fx2-cmd.h"
15
16
17
18 /* Firmware mailbox flags - definitions found from ivtv */
19 #define IVTV_MBOX_FIRMWARE_DONE 0x00000004
20 #define IVTV_MBOX_DRIVER_DONE 0x00000002
21 #define IVTV_MBOX_DRIVER_BUSY 0x00000001
22
23 #define MBOX_BASE 0x44
24
25
pvr2_encoder_write_words(struct pvr2_hdw * hdw,unsigned int offs,const u32 * data,unsigned int dlen)26 static int pvr2_encoder_write_words(struct pvr2_hdw *hdw,
27 unsigned int offs,
28 const u32 *data, unsigned int dlen)
29 {
30 unsigned int idx,addr;
31 unsigned int bAddr;
32 int ret;
33 unsigned int chunkCnt;
34
35 /*
36
37 Format: First byte must be 0x01. Remaining 32 bit words are
38 spread out into chunks of 7 bytes each, with the first 4 bytes
39 being the data word (little endian), and the next 3 bytes
40 being the address where that data word is to be written (big
41 endian). Repeat request for additional words, with offset
42 adjusted accordingly.
43
44 */
45 while (dlen) {
46 chunkCnt = 8;
47 if (chunkCnt > dlen) chunkCnt = dlen;
48 memset(hdw->cmd_buffer,0,sizeof(hdw->cmd_buffer));
49 bAddr = 0;
50 hdw->cmd_buffer[bAddr++] = FX2CMD_MEM_WRITE_DWORD;
51 for (idx = 0; idx < chunkCnt; idx++) {
52 addr = idx + offs;
53 hdw->cmd_buffer[bAddr+6] = (addr & 0xffu);
54 hdw->cmd_buffer[bAddr+5] = ((addr>>8) & 0xffu);
55 hdw->cmd_buffer[bAddr+4] = ((addr>>16) & 0xffu);
56 PVR2_DECOMPOSE_LE(hdw->cmd_buffer, bAddr,data[idx]);
57 bAddr += 7;
58 }
59 ret = pvr2_send_request(hdw,
60 hdw->cmd_buffer,1+(chunkCnt*7),
61 NULL,0);
62 if (ret) return ret;
63 data += chunkCnt;
64 dlen -= chunkCnt;
65 offs += chunkCnt;
66 }
67
68 return 0;
69 }
70
71
pvr2_encoder_read_words(struct pvr2_hdw * hdw,unsigned int offs,u32 * data,unsigned int dlen)72 static int pvr2_encoder_read_words(struct pvr2_hdw *hdw,
73 unsigned int offs,
74 u32 *data, unsigned int dlen)
75 {
76 unsigned int idx;
77 int ret;
78 unsigned int chunkCnt;
79
80 /*
81
82 Format: First byte must be 0x02 (status check) or 0x28 (read
83 back block of 32 bit words). Next 6 bytes must be zero,
84 followed by a single byte of MBOX_BASE+offset for portion to
85 be read. Returned data is packed set of 32 bits words that
86 were read.
87
88 */
89
90 while (dlen) {
91 chunkCnt = 16;
92 if (chunkCnt > dlen) chunkCnt = dlen;
93 if (chunkCnt < 16) chunkCnt = 1;
94 hdw->cmd_buffer[0] =
95 ((chunkCnt == 1) ?
96 FX2CMD_MEM_READ_DWORD : FX2CMD_MEM_READ_64BYTES);
97 hdw->cmd_buffer[1] = 0;
98 hdw->cmd_buffer[2] = 0;
99 hdw->cmd_buffer[3] = 0;
100 hdw->cmd_buffer[4] = 0;
101 hdw->cmd_buffer[5] = ((offs>>16) & 0xffu);
102 hdw->cmd_buffer[6] = ((offs>>8) & 0xffu);
103 hdw->cmd_buffer[7] = (offs & 0xffu);
104 ret = pvr2_send_request(hdw,
105 hdw->cmd_buffer,8,
106 hdw->cmd_buffer,
107 (chunkCnt == 1 ? 4 : 16 * 4));
108 if (ret) return ret;
109
110 for (idx = 0; idx < chunkCnt; idx++) {
111 data[idx] = PVR2_COMPOSE_LE(hdw->cmd_buffer,idx*4);
112 }
113 data += chunkCnt;
114 dlen -= chunkCnt;
115 offs += chunkCnt;
116 }
117
118 return 0;
119 }
120
121
122 /* This prototype is set up to be compatible with the
123 cx2341x_mbox_func prototype in cx2341x.h, which should be in
124 kernels 2.6.18 or later. We do this so that we can enable
125 cx2341x.ko to write to our encoder (by handing it a pointer to this
126 function). For earlier kernels this doesn't really matter. */
pvr2_encoder_cmd(void * ctxt,u32 cmd,int arg_cnt_send,int arg_cnt_recv,u32 * argp)127 static int pvr2_encoder_cmd(void *ctxt,
128 u32 cmd,
129 int arg_cnt_send,
130 int arg_cnt_recv,
131 u32 *argp)
132 {
133 unsigned int poll_count;
134 unsigned int try_count = 0;
135 int retry_flag;
136 int ret = 0;
137 unsigned int idx;
138 /* These sizes look to be limited by the FX2 firmware implementation */
139 u32 wrData[16];
140 u32 rdData[16];
141 struct pvr2_hdw *hdw = (struct pvr2_hdw *)ctxt;
142
143
144 /*
145
146 The encoder seems to speak entirely using blocks 32 bit words.
147 In ivtv driver terms, this is a mailbox at MBOX_BASE which we
148 populate with data and watch what the hardware does with it.
149 The first word is a set of flags used to control the
150 transaction, the second word is the command to execute, the
151 third byte is zero (ivtv driver suggests that this is some
152 kind of return value), and the fourth byte is a specified
153 timeout (windows driver always uses 0x00060000 except for one
154 case when it is zero). All successive words are the argument
155 words for the command.
156
157 First, write out the entire set of words, with the first word
158 being zero.
159
160 Next, write out just the first word again, but set it to
161 IVTV_MBOX_DRIVER_DONE | IVTV_DRIVER_BUSY this time (which
162 probably means "go").
163
164 Next, read back the return count words. Check the first word,
165 which should have IVTV_MBOX_FIRMWARE_DONE set. If however
166 that bit is not set, then the command isn't done so repeat the
167 read until it is set.
168
169 Finally, write out just the first word again, but set it to
170 0x0 this time (which probably means "idle").
171
172 */
173
174 if (arg_cnt_send > (ARRAY_SIZE(wrData) - 4)) {
175 pvr2_trace(
176 PVR2_TRACE_ERROR_LEGS,
177 "Failed to write cx23416 command - too many input arguments (was given %u limit %lu)",
178 arg_cnt_send, (long unsigned) ARRAY_SIZE(wrData) - 4);
179 return -EINVAL;
180 }
181
182 if (arg_cnt_recv > (ARRAY_SIZE(rdData) - 4)) {
183 pvr2_trace(
184 PVR2_TRACE_ERROR_LEGS,
185 "Failed to write cx23416 command - too many return arguments (was given %u limit %lu)",
186 arg_cnt_recv, (long unsigned) ARRAY_SIZE(rdData) - 4);
187 return -EINVAL;
188 }
189
190
191 LOCK_TAKE(hdw->ctl_lock);
192 while (1) {
193 if (!hdw->state_encoder_ok) {
194 ret = -EIO;
195 break;
196 }
197
198 retry_flag = 0;
199 try_count++;
200 ret = 0;
201 wrData[0] = 0;
202 wrData[1] = cmd;
203 wrData[2] = 0;
204 wrData[3] = 0x00060000;
205 for (idx = 0; idx < arg_cnt_send; idx++) {
206 wrData[idx+4] = argp[idx];
207 }
208 for (; idx < ARRAY_SIZE(wrData) - 4; idx++) {
209 wrData[idx+4] = 0;
210 }
211
212 ret = pvr2_encoder_write_words(hdw,MBOX_BASE,wrData,idx);
213 if (ret) break;
214 wrData[0] = IVTV_MBOX_DRIVER_DONE|IVTV_MBOX_DRIVER_BUSY;
215 ret = pvr2_encoder_write_words(hdw,MBOX_BASE,wrData,1);
216 if (ret) break;
217 poll_count = 0;
218 while (1) {
219 poll_count++;
220 ret = pvr2_encoder_read_words(hdw,MBOX_BASE,rdData,
221 arg_cnt_recv+4);
222 if (ret) {
223 break;
224 }
225 if (rdData[0] & IVTV_MBOX_FIRMWARE_DONE) {
226 break;
227 }
228 if (rdData[0] && (poll_count < 1000)) continue;
229 if (!rdData[0]) {
230 retry_flag = !0;
231 pvr2_trace(
232 PVR2_TRACE_ERROR_LEGS,
233 "Encoder timed out waiting for us; arranging to retry");
234 } else {
235 pvr2_trace(
236 PVR2_TRACE_ERROR_LEGS,
237 "***WARNING*** device's encoder appears to be stuck (status=0x%08x)",
238 rdData[0]);
239 }
240 pvr2_trace(
241 PVR2_TRACE_ERROR_LEGS,
242 "Encoder command: 0x%02x",cmd);
243 for (idx = 4; idx < arg_cnt_send; idx++) {
244 pvr2_trace(
245 PVR2_TRACE_ERROR_LEGS,
246 "Encoder arg%d: 0x%08x",
247 idx-3,wrData[idx]);
248 }
249 ret = -EBUSY;
250 break;
251 }
252 if (retry_flag) {
253 if (try_count < 20) continue;
254 pvr2_trace(
255 PVR2_TRACE_ERROR_LEGS,
256 "Too many retries...");
257 ret = -EBUSY;
258 }
259 if (ret) {
260 del_timer_sync(&hdw->encoder_run_timer);
261 hdw->state_encoder_ok = 0;
262 pvr2_trace(PVR2_TRACE_STBITS,
263 "State bit %s <-- %s",
264 "state_encoder_ok",
265 (hdw->state_encoder_ok ? "true" : "false"));
266 if (hdw->state_encoder_runok) {
267 hdw->state_encoder_runok = 0;
268 pvr2_trace(PVR2_TRACE_STBITS,
269 "State bit %s <-- %s",
270 "state_encoder_runok",
271 (hdw->state_encoder_runok ?
272 "true" : "false"));
273 }
274 pvr2_trace(
275 PVR2_TRACE_ERROR_LEGS,
276 "Giving up on command. This is normally recovered via a firmware reload and re-initialization; concern is only warranted if this happens repeatedly and rapidly.");
277 break;
278 }
279 wrData[0] = 0x7;
280 for (idx = 0; idx < arg_cnt_recv; idx++) {
281 argp[idx] = rdData[idx+4];
282 }
283
284 wrData[0] = 0x0;
285 ret = pvr2_encoder_write_words(hdw,MBOX_BASE,wrData,1);
286 break;
287 }
288 LOCK_GIVE(hdw->ctl_lock);
289
290 return ret;
291 }
292
293
pvr2_encoder_vcmd(struct pvr2_hdw * hdw,int cmd,int args,...)294 static int pvr2_encoder_vcmd(struct pvr2_hdw *hdw, int cmd,
295 int args, ...)
296 {
297 va_list vl;
298 unsigned int idx;
299 u32 data[12];
300
301 if (args > ARRAY_SIZE(data)) {
302 pvr2_trace(
303 PVR2_TRACE_ERROR_LEGS,
304 "Failed to write cx23416 command - too many arguments (was given %u limit %lu)",
305 args, (long unsigned) ARRAY_SIZE(data));
306 return -EINVAL;
307 }
308
309 va_start(vl, args);
310 for (idx = 0; idx < args; idx++) {
311 data[idx] = va_arg(vl, u32);
312 }
313 va_end(vl);
314
315 return pvr2_encoder_cmd(hdw,cmd,args,0,data);
316 }
317
318
319 /* This implements some extra setup for the encoder that seems to be
320 specific to the PVR USB2 hardware. */
pvr2_encoder_prep_config(struct pvr2_hdw * hdw)321 static int pvr2_encoder_prep_config(struct pvr2_hdw *hdw)
322 {
323 int ret = 0;
324 int encMisc3Arg = 0;
325
326 #if 0
327 /* This inexplicable bit happens in the Hauppauge windows
328 driver (for both 24xxx and 29xxx devices). However I
329 currently see no difference in behavior with or without
330 this stuff. Leave this here as a note of its existence,
331 but don't use it. */
332 LOCK_TAKE(hdw->ctl_lock); do {
333 u32 dat[1];
334 dat[0] = 0x80000640;
335 pvr2_encoder_write_words(hdw,0x01fe,dat,1);
336 pvr2_encoder_write_words(hdw,0x023e,dat,1);
337 } while(0); LOCK_GIVE(hdw->ctl_lock);
338 #endif
339
340 /* Mike Isely <isely@pobox.com> 26-Jan-2006 The windows driver
341 sends the following list of ENC_MISC commands (for both
342 24xxx and 29xxx devices). Meanings are not entirely clear,
343 however without the ENC_MISC(3,1) command then we risk
344 random perpetual video corruption whenever the video input
345 breaks up for a moment (like when switching channels). */
346
347
348 #if 0
349 /* This ENC_MISC(5,0) command seems to hurt 29xxx sync
350 performance on channel changes, but is not a problem on
351 24xxx devices. */
352 ret |= pvr2_encoder_vcmd(hdw, CX2341X_ENC_MISC,4, 5,0,0,0);
353 #endif
354
355 /* This ENC_MISC(3,encMisc3Arg) command is critical - without
356 it there will eventually be video corruption. Also, the
357 saa7115 case is strange - the Windows driver is passing 1
358 regardless of device type but if we have 1 for saa7115
359 devices the video turns sluggish. */
360 if (hdw->hdw_desc->flag_has_cx25840) {
361 encMisc3Arg = 1;
362 } else {
363 encMisc3Arg = 0;
364 }
365 ret |= pvr2_encoder_vcmd(hdw, CX2341X_ENC_MISC,4, 3,
366 encMisc3Arg,0,0);
367
368 ret |= pvr2_encoder_vcmd(hdw, CX2341X_ENC_MISC,4, 8,0,0,0);
369
370 #if 0
371 /* This ENC_MISC(4,1) command is poisonous, so it is commented
372 out. But I'm leaving it here anyway to document its
373 existence in the Windows driver. The effect of this
374 command is that apps displaying the stream become sluggish
375 with stuttering video. */
376 ret |= pvr2_encoder_vcmd(hdw, CX2341X_ENC_MISC,4, 4,1,0,0);
377 #endif
378
379 ret |= pvr2_encoder_vcmd(hdw, CX2341X_ENC_MISC,4, 0,3,0,0);
380 ret |= pvr2_encoder_vcmd(hdw, CX2341X_ENC_MISC,4,15,0,0,0);
381
382 /* prevent the PTSs from slowly drifting away in the generated
383 MPEG stream */
384 ret |= pvr2_encoder_vcmd(hdw, CX2341X_ENC_MISC, 2, 4, 1);
385
386 return ret;
387 }
388
pvr2_encoder_adjust(struct pvr2_hdw * hdw)389 int pvr2_encoder_adjust(struct pvr2_hdw *hdw)
390 {
391 int ret;
392 ret = cx2341x_update(hdw,pvr2_encoder_cmd,
393 (hdw->enc_cur_valid ? &hdw->enc_cur_state : NULL),
394 &hdw->enc_ctl_state);
395 if (ret) {
396 pvr2_trace(PVR2_TRACE_ERROR_LEGS,
397 "Error from cx2341x module code=%d",ret);
398 } else {
399 hdw->enc_cur_state = hdw->enc_ctl_state;
400 hdw->enc_cur_valid = !0;
401 }
402 return ret;
403 }
404
405
pvr2_encoder_configure(struct pvr2_hdw * hdw)406 int pvr2_encoder_configure(struct pvr2_hdw *hdw)
407 {
408 int ret;
409 int val;
410 pvr2_trace(PVR2_TRACE_ENCODER, "pvr2_encoder_configure (cx2341x module)");
411 hdw->enc_ctl_state.port = CX2341X_PORT_STREAMING;
412 hdw->enc_ctl_state.width = hdw->res_hor_val;
413 hdw->enc_ctl_state.height = hdw->res_ver_val;
414 hdw->enc_ctl_state.is_50hz = ((hdw->std_mask_cur & V4L2_STD_525_60) ?
415 0 : 1);
416
417 ret = 0;
418
419 ret |= pvr2_encoder_prep_config(hdw);
420
421 /* saa7115: 0xf0 */
422 val = 0xf0;
423 if (hdw->hdw_desc->flag_has_cx25840) {
424 /* ivtv cx25840: 0x140 */
425 val = 0x140;
426 }
427
428 if (!ret) ret = pvr2_encoder_vcmd(
429 hdw,CX2341X_ENC_SET_NUM_VSYNC_LINES, 2,
430 val, val);
431
432 /* setup firmware to notify us about some events (don't know why...) */
433 if (!ret) ret = pvr2_encoder_vcmd(
434 hdw,CX2341X_ENC_SET_EVENT_NOTIFICATION, 4,
435 0, 0, 0x10000000, 0xffffffff);
436
437 if (!ret) ret = pvr2_encoder_vcmd(
438 hdw,CX2341X_ENC_SET_VBI_LINE, 5,
439 0xffffffff,0,0,0,0);
440
441 if (ret) {
442 pvr2_trace(PVR2_TRACE_ERROR_LEGS,
443 "Failed to configure cx23416");
444 return ret;
445 }
446
447 ret = pvr2_encoder_adjust(hdw);
448 if (ret) return ret;
449
450 ret = pvr2_encoder_vcmd(
451 hdw, CX2341X_ENC_INITIALIZE_INPUT, 0);
452
453 if (ret) {
454 pvr2_trace(PVR2_TRACE_ERROR_LEGS,
455 "Failed to initialize cx23416 video input");
456 return ret;
457 }
458
459 return 0;
460 }
461
462
pvr2_encoder_start(struct pvr2_hdw * hdw)463 int pvr2_encoder_start(struct pvr2_hdw *hdw)
464 {
465 int status;
466
467 /* unmask some interrupts */
468 pvr2_write_register(hdw, 0x0048, 0xbfffffff);
469
470 pvr2_encoder_vcmd(hdw,CX2341X_ENC_MUTE_VIDEO,1,
471 hdw->input_val == PVR2_CVAL_INPUT_RADIO ? 1 : 0);
472
473 switch (hdw->active_stream_type) {
474 case pvr2_config_vbi:
475 status = pvr2_encoder_vcmd(hdw,CX2341X_ENC_START_CAPTURE,2,
476 0x01,0x14);
477 break;
478 case pvr2_config_mpeg:
479 status = pvr2_encoder_vcmd(hdw,CX2341X_ENC_START_CAPTURE,2,
480 0,0x13);
481 break;
482 default: /* Unhandled cases for now */
483 status = pvr2_encoder_vcmd(hdw,CX2341X_ENC_START_CAPTURE,2,
484 0,0x13);
485 break;
486 }
487 return status;
488 }
489
pvr2_encoder_stop(struct pvr2_hdw * hdw)490 int pvr2_encoder_stop(struct pvr2_hdw *hdw)
491 {
492 int status;
493
494 /* mask all interrupts */
495 pvr2_write_register(hdw, 0x0048, 0xffffffff);
496
497 switch (hdw->active_stream_type) {
498 case pvr2_config_vbi:
499 status = pvr2_encoder_vcmd(hdw,CX2341X_ENC_STOP_CAPTURE,3,
500 0x01,0x01,0x14);
501 break;
502 case pvr2_config_mpeg:
503 status = pvr2_encoder_vcmd(hdw,CX2341X_ENC_STOP_CAPTURE,3,
504 0x01,0,0x13);
505 break;
506 default: /* Unhandled cases for now */
507 status = pvr2_encoder_vcmd(hdw,CX2341X_ENC_STOP_CAPTURE,3,
508 0x01,0,0x13);
509 break;
510 }
511
512 return status;
513 }
514