1 /* 2 * winbond-cir.c - Driver for the Consumer IR functionality of Winbond 3 * SuperI/O chips. 4 * 5 * Currently supports the Winbond WPCD376i chip (PNP id WEC1022), but 6 * could probably support others (Winbond WEC102X, NatSemi, etc) 7 * with minor modifications. 8 * 9 * Original Author: David Härdeman <david@hardeman.nu> 10 * Copyright (C) 2012 Sean Young <sean@mess.org> 11 * Copyright (C) 2009 - 2011 David Härdeman <david@hardeman.nu> 12 * 13 * Dedicated to my daughter Matilda, without whose loving attention this 14 * driver would have been finished in half the time and with a fraction 15 * of the bugs. 16 * 17 * Written using: 18 * o Winbond WPCD376I datasheet helpfully provided by Jesse Barnes at Intel 19 * o NatSemi PC87338/PC97338 datasheet (for the serial port stuff) 20 * o DSDT dumps 21 * 22 * Supported features: 23 * o IR Receive 24 * o IR Transmit 25 * o Wake-On-CIR functionality 26 * o Carrier detection 27 * 28 * This program is free software; you can redistribute it and/or modify 29 * it under the terms of the GNU General Public License as published by 30 * the Free Software Foundation; either version 2 of the License, or 31 * (at your option) any later version. 32 * 33 * This program is distributed in the hope that it will be useful, 34 * but WITHOUT ANY WARRANTY; without even the implied warranty of 35 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 36 * GNU General Public License for more details. 37 * 38 * You should have received a copy of the GNU General Public License 39 * along with this program; if not, write to the Free Software 40 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 41 */ 42 43 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 44 45 #include <linux/module.h> 46 #include <linux/pnp.h> 47 #include <linux/interrupt.h> 48 #include <linux/timer.h> 49 #include <linux/leds.h> 50 #include <linux/spinlock.h> 51 #include <linux/pci_ids.h> 52 #include <linux/io.h> 53 #include <linux/bitrev.h> 54 #include <linux/slab.h> 55 #include <linux/wait.h> 56 #include <linux/sched.h> 57 #include <media/rc-core.h> 58 59 #define DRVNAME "winbond-cir" 60 61 /* CEIR Wake-Up Registers, relative to data->wbase */ 62 #define WBCIR_REG_WCEIR_CTL 0x03 /* CEIR Receiver Control */ 63 #define WBCIR_REG_WCEIR_STS 0x04 /* CEIR Receiver Status */ 64 #define WBCIR_REG_WCEIR_EV_EN 0x05 /* CEIR Receiver Event Enable */ 65 #define WBCIR_REG_WCEIR_CNTL 0x06 /* CEIR Receiver Counter Low */ 66 #define WBCIR_REG_WCEIR_CNTH 0x07 /* CEIR Receiver Counter High */ 67 #define WBCIR_REG_WCEIR_INDEX 0x08 /* CEIR Receiver Index */ 68 #define WBCIR_REG_WCEIR_DATA 0x09 /* CEIR Receiver Data */ 69 #define WBCIR_REG_WCEIR_CSL 0x0A /* CEIR Re. Compare Strlen */ 70 #define WBCIR_REG_WCEIR_CFG1 0x0B /* CEIR Re. Configuration 1 */ 71 #define WBCIR_REG_WCEIR_CFG2 0x0C /* CEIR Re. Configuration 2 */ 72 73 /* CEIR Enhanced Functionality Registers, relative to data->ebase */ 74 #define WBCIR_REG_ECEIR_CTS 0x00 /* Enhanced IR Control Status */ 75 #define WBCIR_REG_ECEIR_CCTL 0x01 /* Infrared Counter Control */ 76 #define WBCIR_REG_ECEIR_CNT_LO 0x02 /* Infrared Counter LSB */ 77 #define WBCIR_REG_ECEIR_CNT_HI 0x03 /* Infrared Counter MSB */ 78 #define WBCIR_REG_ECEIR_IREM 0x04 /* Infrared Emitter Status */ 79 80 /* SP3 Banked Registers, relative to data->sbase */ 81 #define WBCIR_REG_SP3_BSR 0x03 /* Bank Select, all banks */ 82 /* Bank 0 */ 83 #define WBCIR_REG_SP3_RXDATA 0x00 /* FIFO RX data (r) */ 84 #define WBCIR_REG_SP3_TXDATA 0x00 /* FIFO TX data (w) */ 85 #define WBCIR_REG_SP3_IER 0x01 /* Interrupt Enable */ 86 #define WBCIR_REG_SP3_EIR 0x02 /* Event Identification (r) */ 87 #define WBCIR_REG_SP3_FCR 0x02 /* FIFO Control (w) */ 88 #define WBCIR_REG_SP3_MCR 0x04 /* Mode Control */ 89 #define WBCIR_REG_SP3_LSR 0x05 /* Link Status */ 90 #define WBCIR_REG_SP3_MSR 0x06 /* Modem Status */ 91 #define WBCIR_REG_SP3_ASCR 0x07 /* Aux Status and Control */ 92 /* Bank 2 */ 93 #define WBCIR_REG_SP3_BGDL 0x00 /* Baud Divisor LSB */ 94 #define WBCIR_REG_SP3_BGDH 0x01 /* Baud Divisor MSB */ 95 #define WBCIR_REG_SP3_EXCR1 0x02 /* Extended Control 1 */ 96 #define WBCIR_REG_SP3_EXCR2 0x04 /* Extended Control 2 */ 97 #define WBCIR_REG_SP3_TXFLV 0x06 /* TX FIFO Level */ 98 #define WBCIR_REG_SP3_RXFLV 0x07 /* RX FIFO Level */ 99 /* Bank 3 */ 100 #define WBCIR_REG_SP3_MRID 0x00 /* Module Identification */ 101 #define WBCIR_REG_SP3_SH_LCR 0x01 /* LCR Shadow */ 102 #define WBCIR_REG_SP3_SH_FCR 0x02 /* FCR Shadow */ 103 /* Bank 4 */ 104 #define WBCIR_REG_SP3_IRCR1 0x02 /* Infrared Control 1 */ 105 /* Bank 5 */ 106 #define WBCIR_REG_SP3_IRCR2 0x04 /* Infrared Control 2 */ 107 /* Bank 6 */ 108 #define WBCIR_REG_SP3_IRCR3 0x00 /* Infrared Control 3 */ 109 #define WBCIR_REG_SP3_SIR_PW 0x02 /* SIR Pulse Width */ 110 /* Bank 7 */ 111 #define WBCIR_REG_SP3_IRRXDC 0x00 /* IR RX Demod Control */ 112 #define WBCIR_REG_SP3_IRTXMC 0x01 /* IR TX Mod Control */ 113 #define WBCIR_REG_SP3_RCCFG 0x02 /* CEIR Config */ 114 #define WBCIR_REG_SP3_IRCFG1 0x04 /* Infrared Config 1 */ 115 #define WBCIR_REG_SP3_IRCFG4 0x07 /* Infrared Config 4 */ 116 117 /* 118 * Magic values follow 119 */ 120 121 /* No interrupts for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ 122 #define WBCIR_IRQ_NONE 0x00 123 /* RX data bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ 124 #define WBCIR_IRQ_RX 0x01 125 /* TX data low bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ 126 #define WBCIR_IRQ_TX_LOW 0x02 127 /* Over/Under-flow bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ 128 #define WBCIR_IRQ_ERR 0x04 129 /* TX data empty bit for WBCEIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ 130 #define WBCIR_IRQ_TX_EMPTY 0x20 131 /* Led enable/disable bit for WBCIR_REG_ECEIR_CTS */ 132 #define WBCIR_LED_ENABLE 0x80 133 /* RX data available bit for WBCIR_REG_SP3_LSR */ 134 #define WBCIR_RX_AVAIL 0x01 135 /* RX data overrun error bit for WBCIR_REG_SP3_LSR */ 136 #define WBCIR_RX_OVERRUN 0x02 137 /* TX End-Of-Transmission bit for WBCIR_REG_SP3_ASCR */ 138 #define WBCIR_TX_EOT 0x04 139 /* RX disable bit for WBCIR_REG_SP3_ASCR */ 140 #define WBCIR_RX_DISABLE 0x20 141 /* TX data underrun error bit for WBCIR_REG_SP3_ASCR */ 142 #define WBCIR_TX_UNDERRUN 0x40 143 /* Extended mode enable bit for WBCIR_REG_SP3_EXCR1 */ 144 #define WBCIR_EXT_ENABLE 0x01 145 /* Select compare register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */ 146 #define WBCIR_REGSEL_COMPARE 0x10 147 /* Select mask register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */ 148 #define WBCIR_REGSEL_MASK 0x20 149 /* Starting address of selected register in WBCIR_REG_WCEIR_INDEX */ 150 #define WBCIR_REG_ADDR0 0x00 151 /* Enable carrier counter */ 152 #define WBCIR_CNTR_EN 0x01 153 /* Reset carrier counter */ 154 #define WBCIR_CNTR_R 0x02 155 /* Invert TX */ 156 #define WBCIR_IRTX_INV 0x04 157 /* Receiver oversampling */ 158 #define WBCIR_RX_T_OV 0x40 159 160 /* Valid banks for the SP3 UART */ 161 enum wbcir_bank { 162 WBCIR_BANK_0 = 0x00, 163 WBCIR_BANK_1 = 0x80, 164 WBCIR_BANK_2 = 0xE0, 165 WBCIR_BANK_3 = 0xE4, 166 WBCIR_BANK_4 = 0xE8, 167 WBCIR_BANK_5 = 0xEC, 168 WBCIR_BANK_6 = 0xF0, 169 WBCIR_BANK_7 = 0xF4, 170 }; 171 172 /* Supported power-on IR Protocols */ 173 enum wbcir_protocol { 174 IR_PROTOCOL_RC5 = 0x0, 175 IR_PROTOCOL_NEC = 0x1, 176 IR_PROTOCOL_RC6 = 0x2, 177 }; 178 179 /* Possible states for IR reception */ 180 enum wbcir_rxstate { 181 WBCIR_RXSTATE_INACTIVE = 0, 182 WBCIR_RXSTATE_ACTIVE, 183 WBCIR_RXSTATE_ERROR 184 }; 185 186 /* Possible states for IR transmission */ 187 enum wbcir_txstate { 188 WBCIR_TXSTATE_INACTIVE = 0, 189 WBCIR_TXSTATE_ACTIVE, 190 WBCIR_TXSTATE_ERROR 191 }; 192 193 /* Misc */ 194 #define WBCIR_NAME "Winbond CIR" 195 #define WBCIR_ID_FAMILY 0xF1 /* Family ID for the WPCD376I */ 196 #define WBCIR_ID_CHIP 0x04 /* Chip ID for the WPCD376I */ 197 #define INVALID_SCANCODE 0x7FFFFFFF /* Invalid with all protos */ 198 #define WAKEUP_IOMEM_LEN 0x10 /* Wake-Up I/O Reg Len */ 199 #define EHFUNC_IOMEM_LEN 0x10 /* Enhanced Func I/O Reg Len */ 200 #define SP_IOMEM_LEN 0x08 /* Serial Port 3 (IR) Reg Len */ 201 202 /* Per-device data */ 203 struct wbcir_data { 204 spinlock_t spinlock; 205 struct rc_dev *dev; 206 struct led_classdev led; 207 208 unsigned long wbase; /* Wake-Up Baseaddr */ 209 unsigned long ebase; /* Enhanced Func. Baseaddr */ 210 unsigned long sbase; /* Serial Port Baseaddr */ 211 unsigned int irq; /* Serial Port IRQ */ 212 u8 irqmask; 213 214 /* RX state */ 215 enum wbcir_rxstate rxstate; 216 int carrier_report_enabled; 217 u32 pulse_duration; 218 219 /* TX state */ 220 enum wbcir_txstate txstate; 221 u32 txlen; 222 u32 txoff; 223 u32 *txbuf; 224 u8 txmask; 225 u32 txcarrier; 226 }; 227 228 static enum wbcir_protocol protocol = IR_PROTOCOL_RC6; 229 module_param(protocol, uint, 0444); 230 MODULE_PARM_DESC(protocol, "IR protocol to use for the power-on command " 231 "(0 = RC5, 1 = NEC, 2 = RC6A, default)"); 232 233 static bool invert; /* default = 0 */ 234 module_param(invert, bool, 0444); 235 MODULE_PARM_DESC(invert, "Invert the signal from the IR receiver"); 236 237 static bool txandrx; /* default = 0 */ 238 module_param(txandrx, bool, 0444); 239 MODULE_PARM_DESC(txandrx, "Allow simultaneous TX and RX"); 240 241 static unsigned int wake_sc = 0x800F040C; 242 module_param(wake_sc, uint, 0644); 243 MODULE_PARM_DESC(wake_sc, "Scancode of the power-on IR command"); 244 245 static unsigned int wake_rc6mode = 6; 246 module_param(wake_rc6mode, uint, 0644); 247 MODULE_PARM_DESC(wake_rc6mode, "RC6 mode for the power-on command " 248 "(0 = 0, 6 = 6A, default)"); 249 250 251 252 /***************************************************************************** 253 * 254 * UTILITY FUNCTIONS 255 * 256 *****************************************************************************/ 257 258 /* Caller needs to hold wbcir_lock */ 259 static void 260 wbcir_set_bits(unsigned long addr, u8 bits, u8 mask) 261 { 262 u8 val; 263 264 val = inb(addr); 265 val = ((val & ~mask) | (bits & mask)); 266 outb(val, addr); 267 } 268 269 /* Selects the register bank for the serial port */ 270 static inline void 271 wbcir_select_bank(struct wbcir_data *data, enum wbcir_bank bank) 272 { 273 outb(bank, data->sbase + WBCIR_REG_SP3_BSR); 274 } 275 276 static inline void 277 wbcir_set_irqmask(struct wbcir_data *data, u8 irqmask) 278 { 279 if (data->irqmask == irqmask) 280 return; 281 282 wbcir_select_bank(data, WBCIR_BANK_0); 283 outb(irqmask, data->sbase + WBCIR_REG_SP3_IER); 284 data->irqmask = irqmask; 285 } 286 287 static enum led_brightness 288 wbcir_led_brightness_get(struct led_classdev *led_cdev) 289 { 290 struct wbcir_data *data = container_of(led_cdev, 291 struct wbcir_data, 292 led); 293 294 if (inb(data->ebase + WBCIR_REG_ECEIR_CTS) & WBCIR_LED_ENABLE) 295 return LED_FULL; 296 else 297 return LED_OFF; 298 } 299 300 static void 301 wbcir_led_brightness_set(struct led_classdev *led_cdev, 302 enum led_brightness brightness) 303 { 304 struct wbcir_data *data = container_of(led_cdev, 305 struct wbcir_data, 306 led); 307 308 wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CTS, 309 brightness == LED_OFF ? 0x00 : WBCIR_LED_ENABLE, 310 WBCIR_LED_ENABLE); 311 } 312 313 /* Manchester encodes bits to RC6 message cells (see wbcir_shutdown) */ 314 static u8 315 wbcir_to_rc6cells(u8 val) 316 { 317 u8 coded = 0x00; 318 int i; 319 320 val &= 0x0F; 321 for (i = 0; i < 4; i++) { 322 if (val & 0x01) 323 coded |= 0x02 << (i * 2); 324 else 325 coded |= 0x01 << (i * 2); 326 val >>= 1; 327 } 328 329 return coded; 330 } 331 332 /***************************************************************************** 333 * 334 * INTERRUPT FUNCTIONS 335 * 336 *****************************************************************************/ 337 338 static void 339 wbcir_carrier_report(struct wbcir_data *data) 340 { 341 unsigned counter = inb(data->ebase + WBCIR_REG_ECEIR_CNT_LO) | 342 inb(data->ebase + WBCIR_REG_ECEIR_CNT_HI) << 8; 343 344 if (counter > 0 && counter < 0xffff) { 345 DEFINE_IR_RAW_EVENT(ev); 346 347 ev.carrier_report = 1; 348 ev.carrier = DIV_ROUND_CLOSEST(counter * 1000000u, 349 data->pulse_duration); 350 351 ir_raw_event_store(data->dev, &ev); 352 } 353 354 /* reset and restart the counter */ 355 data->pulse_duration = 0; 356 wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, WBCIR_CNTR_R, 357 WBCIR_CNTR_EN | WBCIR_CNTR_R); 358 wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, WBCIR_CNTR_EN, 359 WBCIR_CNTR_EN | WBCIR_CNTR_R); 360 } 361 362 static void 363 wbcir_idle_rx(struct rc_dev *dev, bool idle) 364 { 365 struct wbcir_data *data = dev->priv; 366 367 if (!idle && data->rxstate == WBCIR_RXSTATE_INACTIVE) 368 data->rxstate = WBCIR_RXSTATE_ACTIVE; 369 370 if (idle && data->rxstate != WBCIR_RXSTATE_INACTIVE) { 371 data->rxstate = WBCIR_RXSTATE_INACTIVE; 372 373 if (data->carrier_report_enabled) 374 wbcir_carrier_report(data); 375 376 /* Tell hardware to go idle by setting RXINACTIVE */ 377 outb(WBCIR_RX_DISABLE, data->sbase + WBCIR_REG_SP3_ASCR); 378 } 379 } 380 381 static void 382 wbcir_irq_rx(struct wbcir_data *data, struct pnp_dev *device) 383 { 384 u8 irdata; 385 DEFINE_IR_RAW_EVENT(rawir); 386 unsigned duration; 387 388 /* Since RXHDLEV is set, at least 8 bytes are in the FIFO */ 389 while (inb(data->sbase + WBCIR_REG_SP3_LSR) & WBCIR_RX_AVAIL) { 390 irdata = inb(data->sbase + WBCIR_REG_SP3_RXDATA); 391 if (data->rxstate == WBCIR_RXSTATE_ERROR) 392 continue; 393 394 duration = ((irdata & 0x7F) + 1) * 395 (data->carrier_report_enabled ? 2 : 10); 396 rawir.pulse = irdata & 0x80 ? false : true; 397 rawir.duration = US_TO_NS(duration); 398 399 if (rawir.pulse) 400 data->pulse_duration += duration; 401 402 ir_raw_event_store_with_filter(data->dev, &rawir); 403 } 404 405 ir_raw_event_handle(data->dev); 406 } 407 408 static void 409 wbcir_irq_tx(struct wbcir_data *data) 410 { 411 unsigned int space; 412 unsigned int used; 413 u8 bytes[16]; 414 u8 byte; 415 416 if (!data->txbuf) 417 return; 418 419 switch (data->txstate) { 420 case WBCIR_TXSTATE_INACTIVE: 421 /* TX FIFO empty */ 422 space = 16; 423 break; 424 case WBCIR_TXSTATE_ACTIVE: 425 /* TX FIFO low (3 bytes or less) */ 426 space = 13; 427 break; 428 case WBCIR_TXSTATE_ERROR: 429 space = 0; 430 break; 431 default: 432 return; 433 } 434 435 /* 436 * TX data is run-length coded in bytes: YXXXXXXX 437 * Y = space (1) or pulse (0) 438 * X = duration, encoded as (X + 1) * 10us (i.e 10 to 1280 us) 439 */ 440 for (used = 0; used < space && data->txoff != data->txlen; used++) { 441 if (data->txbuf[data->txoff] == 0) { 442 data->txoff++; 443 continue; 444 } 445 byte = min((u32)0x80, data->txbuf[data->txoff]); 446 data->txbuf[data->txoff] -= byte; 447 byte--; 448 byte |= (data->txoff % 2 ? 0x80 : 0x00); /* pulse/space */ 449 bytes[used] = byte; 450 } 451 452 while (data->txbuf[data->txoff] == 0 && data->txoff != data->txlen) 453 data->txoff++; 454 455 if (used == 0) { 456 /* Finished */ 457 if (data->txstate == WBCIR_TXSTATE_ERROR) 458 /* Clear TX underrun bit */ 459 outb(WBCIR_TX_UNDERRUN, data->sbase + WBCIR_REG_SP3_ASCR); 460 wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR); 461 kfree(data->txbuf); 462 data->txbuf = NULL; 463 data->txstate = WBCIR_TXSTATE_INACTIVE; 464 } else if (data->txoff == data->txlen) { 465 /* At the end of transmission, tell the hw before last byte */ 466 outsb(data->sbase + WBCIR_REG_SP3_TXDATA, bytes, used - 1); 467 outb(WBCIR_TX_EOT, data->sbase + WBCIR_REG_SP3_ASCR); 468 outb(bytes[used - 1], data->sbase + WBCIR_REG_SP3_TXDATA); 469 wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR | 470 WBCIR_IRQ_TX_EMPTY); 471 } else { 472 /* More data to follow... */ 473 outsb(data->sbase + WBCIR_REG_SP3_RXDATA, bytes, used); 474 if (data->txstate == WBCIR_TXSTATE_INACTIVE) { 475 wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR | 476 WBCIR_IRQ_TX_LOW); 477 data->txstate = WBCIR_TXSTATE_ACTIVE; 478 } 479 } 480 } 481 482 static irqreturn_t 483 wbcir_irq_handler(int irqno, void *cookie) 484 { 485 struct pnp_dev *device = cookie; 486 struct wbcir_data *data = pnp_get_drvdata(device); 487 unsigned long flags; 488 u8 status; 489 490 spin_lock_irqsave(&data->spinlock, flags); 491 wbcir_select_bank(data, WBCIR_BANK_0); 492 status = inb(data->sbase + WBCIR_REG_SP3_EIR); 493 status &= data->irqmask; 494 495 if (!status) { 496 spin_unlock_irqrestore(&data->spinlock, flags); 497 return IRQ_NONE; 498 } 499 500 if (status & WBCIR_IRQ_ERR) { 501 /* RX overflow? (read clears bit) */ 502 if (inb(data->sbase + WBCIR_REG_SP3_LSR) & WBCIR_RX_OVERRUN) { 503 data->rxstate = WBCIR_RXSTATE_ERROR; 504 ir_raw_event_reset(data->dev); 505 } 506 507 /* TX underflow? */ 508 if (inb(data->sbase + WBCIR_REG_SP3_ASCR) & WBCIR_TX_UNDERRUN) 509 data->txstate = WBCIR_TXSTATE_ERROR; 510 } 511 512 if (status & WBCIR_IRQ_RX) 513 wbcir_irq_rx(data, device); 514 515 if (status & (WBCIR_IRQ_TX_LOW | WBCIR_IRQ_TX_EMPTY)) 516 wbcir_irq_tx(data); 517 518 spin_unlock_irqrestore(&data->spinlock, flags); 519 return IRQ_HANDLED; 520 } 521 522 /***************************************************************************** 523 * 524 * RC-CORE INTERFACE FUNCTIONS 525 * 526 *****************************************************************************/ 527 528 static int 529 wbcir_set_carrier_report(struct rc_dev *dev, int enable) 530 { 531 struct wbcir_data *data = dev->priv; 532 unsigned long flags; 533 534 spin_lock_irqsave(&data->spinlock, flags); 535 536 if (data->carrier_report_enabled == enable) { 537 spin_unlock_irqrestore(&data->spinlock, flags); 538 return 0; 539 } 540 541 data->pulse_duration = 0; 542 wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, WBCIR_CNTR_R, 543 WBCIR_CNTR_EN | WBCIR_CNTR_R); 544 545 if (enable && data->dev->idle) 546 wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, 547 WBCIR_CNTR_EN, WBCIR_CNTR_EN | WBCIR_CNTR_R); 548 549 /* Set a higher sampling resolution if carrier reports are enabled */ 550 wbcir_select_bank(data, WBCIR_BANK_2); 551 data->dev->rx_resolution = US_TO_NS(enable ? 2 : 10); 552 outb(enable ? 0x03 : 0x0f, data->sbase + WBCIR_REG_SP3_BGDL); 553 outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH); 554 555 /* Enable oversampling if carrier reports are enabled */ 556 wbcir_select_bank(data, WBCIR_BANK_7); 557 wbcir_set_bits(data->sbase + WBCIR_REG_SP3_RCCFG, 558 enable ? WBCIR_RX_T_OV : 0, WBCIR_RX_T_OV); 559 560 data->carrier_report_enabled = enable; 561 spin_unlock_irqrestore(&data->spinlock, flags); 562 563 return 0; 564 } 565 566 static int 567 wbcir_txcarrier(struct rc_dev *dev, u32 carrier) 568 { 569 struct wbcir_data *data = dev->priv; 570 unsigned long flags; 571 u8 val; 572 u32 freq; 573 574 freq = DIV_ROUND_CLOSEST(carrier, 1000); 575 if (freq < 30 || freq > 60) 576 return -EINVAL; 577 578 switch (freq) { 579 case 58: 580 case 59: 581 case 60: 582 val = freq - 58; 583 freq *= 1000; 584 break; 585 case 57: 586 val = freq - 27; 587 freq = 56900; 588 break; 589 default: 590 val = freq - 27; 591 freq *= 1000; 592 break; 593 } 594 595 spin_lock_irqsave(&data->spinlock, flags); 596 if (data->txstate != WBCIR_TXSTATE_INACTIVE) { 597 spin_unlock_irqrestore(&data->spinlock, flags); 598 return -EBUSY; 599 } 600 601 if (data->txcarrier != freq) { 602 wbcir_select_bank(data, WBCIR_BANK_7); 603 wbcir_set_bits(data->sbase + WBCIR_REG_SP3_IRTXMC, val, 0x1F); 604 data->txcarrier = freq; 605 } 606 607 spin_unlock_irqrestore(&data->spinlock, flags); 608 return 0; 609 } 610 611 static int 612 wbcir_txmask(struct rc_dev *dev, u32 mask) 613 { 614 struct wbcir_data *data = dev->priv; 615 unsigned long flags; 616 u8 val; 617 618 /* Four outputs, only one output can be enabled at a time */ 619 switch (mask) { 620 case 0x1: 621 val = 0x0; 622 break; 623 case 0x2: 624 val = 0x1; 625 break; 626 case 0x4: 627 val = 0x2; 628 break; 629 case 0x8: 630 val = 0x3; 631 break; 632 default: 633 return -EINVAL; 634 } 635 636 spin_lock_irqsave(&data->spinlock, flags); 637 if (data->txstate != WBCIR_TXSTATE_INACTIVE) { 638 spin_unlock_irqrestore(&data->spinlock, flags); 639 return -EBUSY; 640 } 641 642 if (data->txmask != mask) { 643 wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CTS, val, 0x0c); 644 data->txmask = mask; 645 } 646 647 spin_unlock_irqrestore(&data->spinlock, flags); 648 return 0; 649 } 650 651 static int 652 wbcir_tx(struct rc_dev *dev, unsigned *b, unsigned count) 653 { 654 struct wbcir_data *data = dev->priv; 655 unsigned *buf; 656 unsigned i; 657 unsigned long flags; 658 659 buf = kmalloc(count * sizeof(*b), GFP_KERNEL); 660 if (!buf) 661 return -ENOMEM; 662 663 /* Convert values to multiples of 10us */ 664 for (i = 0; i < count; i++) 665 buf[i] = DIV_ROUND_CLOSEST(b[i], 10); 666 667 /* Not sure if this is possible, but better safe than sorry */ 668 spin_lock_irqsave(&data->spinlock, flags); 669 if (data->txstate != WBCIR_TXSTATE_INACTIVE) { 670 spin_unlock_irqrestore(&data->spinlock, flags); 671 kfree(buf); 672 return -EBUSY; 673 } 674 675 /* Fill the TX fifo once, the irq handler will do the rest */ 676 data->txbuf = buf; 677 data->txlen = count; 678 data->txoff = 0; 679 wbcir_irq_tx(data); 680 681 /* We're done */ 682 spin_unlock_irqrestore(&data->spinlock, flags); 683 return count; 684 } 685 686 /***************************************************************************** 687 * 688 * SETUP/INIT/SUSPEND/RESUME FUNCTIONS 689 * 690 *****************************************************************************/ 691 692 static void 693 wbcir_shutdown(struct pnp_dev *device) 694 { 695 struct device *dev = &device->dev; 696 struct wbcir_data *data = pnp_get_drvdata(device); 697 bool do_wake = true; 698 u8 match[11]; 699 u8 mask[11]; 700 u8 rc6_csl = 0; 701 int i; 702 703 memset(match, 0, sizeof(match)); 704 memset(mask, 0, sizeof(mask)); 705 706 if (wake_sc == INVALID_SCANCODE || !device_may_wakeup(dev)) { 707 do_wake = false; 708 goto finish; 709 } 710 711 switch (protocol) { 712 case IR_PROTOCOL_RC5: 713 if (wake_sc > 0xFFF) { 714 do_wake = false; 715 dev_err(dev, "RC5 - Invalid wake scancode\n"); 716 break; 717 } 718 719 /* Mask = 13 bits, ex toggle */ 720 mask[0] = 0xFF; 721 mask[1] = 0x17; 722 723 match[0] = (wake_sc & 0x003F); /* 6 command bits */ 724 match[0] |= (wake_sc & 0x0180) >> 1; /* 2 address bits */ 725 match[1] = (wake_sc & 0x0E00) >> 9; /* 3 address bits */ 726 if (!(wake_sc & 0x0040)) /* 2nd start bit */ 727 match[1] |= 0x10; 728 729 break; 730 731 case IR_PROTOCOL_NEC: 732 if (wake_sc > 0xFFFFFF) { 733 do_wake = false; 734 dev_err(dev, "NEC - Invalid wake scancode\n"); 735 break; 736 } 737 738 mask[0] = mask[1] = mask[2] = mask[3] = 0xFF; 739 740 match[1] = bitrev8((wake_sc & 0xFF)); 741 match[0] = ~match[1]; 742 743 match[3] = bitrev8((wake_sc & 0xFF00) >> 8); 744 if (wake_sc > 0xFFFF) 745 match[2] = bitrev8((wake_sc & 0xFF0000) >> 16); 746 else 747 match[2] = ~match[3]; 748 749 break; 750 751 case IR_PROTOCOL_RC6: 752 753 if (wake_rc6mode == 0) { 754 if (wake_sc > 0xFFFF) { 755 do_wake = false; 756 dev_err(dev, "RC6 - Invalid wake scancode\n"); 757 break; 758 } 759 760 /* Command */ 761 match[0] = wbcir_to_rc6cells(wake_sc >> 0); 762 mask[0] = 0xFF; 763 match[1] = wbcir_to_rc6cells(wake_sc >> 4); 764 mask[1] = 0xFF; 765 766 /* Address */ 767 match[2] = wbcir_to_rc6cells(wake_sc >> 8); 768 mask[2] = 0xFF; 769 match[3] = wbcir_to_rc6cells(wake_sc >> 12); 770 mask[3] = 0xFF; 771 772 /* Header */ 773 match[4] = 0x50; /* mode1 = mode0 = 0, ignore toggle */ 774 mask[4] = 0xF0; 775 match[5] = 0x09; /* start bit = 1, mode2 = 0 */ 776 mask[5] = 0x0F; 777 778 rc6_csl = 44; 779 780 } else if (wake_rc6mode == 6) { 781 i = 0; 782 783 /* Command */ 784 match[i] = wbcir_to_rc6cells(wake_sc >> 0); 785 mask[i++] = 0xFF; 786 match[i] = wbcir_to_rc6cells(wake_sc >> 4); 787 mask[i++] = 0xFF; 788 789 /* Address + Toggle */ 790 match[i] = wbcir_to_rc6cells(wake_sc >> 8); 791 mask[i++] = 0xFF; 792 match[i] = wbcir_to_rc6cells(wake_sc >> 12); 793 mask[i++] = 0x3F; 794 795 /* Customer bits 7 - 0 */ 796 match[i] = wbcir_to_rc6cells(wake_sc >> 16); 797 mask[i++] = 0xFF; 798 match[i] = wbcir_to_rc6cells(wake_sc >> 20); 799 mask[i++] = 0xFF; 800 801 if (wake_sc & 0x80000000) { 802 /* Customer range bit and bits 15 - 8 */ 803 match[i] = wbcir_to_rc6cells(wake_sc >> 24); 804 mask[i++] = 0xFF; 805 match[i] = wbcir_to_rc6cells(wake_sc >> 28); 806 mask[i++] = 0xFF; 807 rc6_csl = 76; 808 } else if (wake_sc <= 0x007FFFFF) { 809 rc6_csl = 60; 810 } else { 811 do_wake = false; 812 dev_err(dev, "RC6 - Invalid wake scancode\n"); 813 break; 814 } 815 816 /* Header */ 817 match[i] = 0x93; /* mode1 = mode0 = 1, submode = 0 */ 818 mask[i++] = 0xFF; 819 match[i] = 0x0A; /* start bit = 1, mode2 = 1 */ 820 mask[i++] = 0x0F; 821 822 } else { 823 do_wake = false; 824 dev_err(dev, "RC6 - Invalid wake mode\n"); 825 } 826 827 break; 828 829 default: 830 do_wake = false; 831 break; 832 } 833 834 finish: 835 if (do_wake) { 836 /* Set compare and compare mask */ 837 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX, 838 WBCIR_REGSEL_COMPARE | WBCIR_REG_ADDR0, 839 0x3F); 840 outsb(data->wbase + WBCIR_REG_WCEIR_DATA, match, 11); 841 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX, 842 WBCIR_REGSEL_MASK | WBCIR_REG_ADDR0, 843 0x3F); 844 outsb(data->wbase + WBCIR_REG_WCEIR_DATA, mask, 11); 845 846 /* RC6 Compare String Len */ 847 outb(rc6_csl, data->wbase + WBCIR_REG_WCEIR_CSL); 848 849 /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */ 850 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17); 851 852 /* Clear BUFF_EN, Clear END_EN, Set MATCH_EN */ 853 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x01, 0x07); 854 855 /* Set CEIR_EN */ 856 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x01, 0x01); 857 858 } else { 859 /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */ 860 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); 861 862 /* Clear CEIR_EN */ 863 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01); 864 } 865 866 /* 867 * ACPI will set the HW disable bit for SP3 which means that the 868 * output signals are left in an undefined state which may cause 869 * spurious interrupts which we need to ignore until the hardware 870 * is reinitialized. 871 */ 872 wbcir_set_irqmask(data, WBCIR_IRQ_NONE); 873 disable_irq(data->irq); 874 } 875 876 static int 877 wbcir_suspend(struct pnp_dev *device, pm_message_t state) 878 { 879 struct wbcir_data *data = pnp_get_drvdata(device); 880 led_classdev_suspend(&data->led); 881 wbcir_shutdown(device); 882 return 0; 883 } 884 885 static void 886 wbcir_init_hw(struct wbcir_data *data) 887 { 888 u8 tmp; 889 890 /* Disable interrupts */ 891 wbcir_set_irqmask(data, WBCIR_IRQ_NONE); 892 893 /* Set PROT_SEL, RX_INV, Clear CEIR_EN (needed for the led) */ 894 tmp = protocol << 4; 895 if (invert) 896 tmp |= 0x08; 897 outb(tmp, data->wbase + WBCIR_REG_WCEIR_CTL); 898 899 /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */ 900 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17); 901 902 /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */ 903 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); 904 905 /* Set RC5 cell time to correspond to 36 kHz */ 906 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CFG1, 0x4A, 0x7F); 907 908 /* Set IRTX_INV */ 909 if (invert) 910 outb(WBCIR_IRTX_INV, data->ebase + WBCIR_REG_ECEIR_CCTL); 911 else 912 outb(0x00, data->ebase + WBCIR_REG_ECEIR_CCTL); 913 914 /* 915 * Clear IR LED, set SP3 clock to 24Mhz, set TX mask to IRTX1, 916 * set SP3_IRRX_SW to binary 01, helpfully not documented 917 */ 918 outb(0x10, data->ebase + WBCIR_REG_ECEIR_CTS); 919 data->txmask = 0x1; 920 921 /* Enable extended mode */ 922 wbcir_select_bank(data, WBCIR_BANK_2); 923 outb(WBCIR_EXT_ENABLE, data->sbase + WBCIR_REG_SP3_EXCR1); 924 925 /* 926 * Configure baud generator, IR data will be sampled at 927 * a bitrate of: (24Mhz * prescaler) / (divisor * 16). 928 * 929 * The ECIR registers include a flag to change the 930 * 24Mhz clock freq to 48Mhz. 931 * 932 * It's not documented in the specs, but fifo levels 933 * other than 16 seems to be unsupported. 934 */ 935 936 /* prescaler 1.0, tx/rx fifo lvl 16 */ 937 outb(0x30, data->sbase + WBCIR_REG_SP3_EXCR2); 938 939 /* Set baud divisor to sample every 10 us */ 940 outb(0x0f, data->sbase + WBCIR_REG_SP3_BGDL); 941 outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH); 942 943 /* Set CEIR mode */ 944 wbcir_select_bank(data, WBCIR_BANK_0); 945 outb(0xC0, data->sbase + WBCIR_REG_SP3_MCR); 946 inb(data->sbase + WBCIR_REG_SP3_LSR); /* Clear LSR */ 947 inb(data->sbase + WBCIR_REG_SP3_MSR); /* Clear MSR */ 948 949 /* Disable RX demod, enable run-length enc/dec, set freq span */ 950 wbcir_select_bank(data, WBCIR_BANK_7); 951 outb(0x90, data->sbase + WBCIR_REG_SP3_RCCFG); 952 953 /* Disable timer */ 954 wbcir_select_bank(data, WBCIR_BANK_4); 955 outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR1); 956 957 /* Disable MSR interrupt, clear AUX_IRX, mask RX during TX? */ 958 wbcir_select_bank(data, WBCIR_BANK_5); 959 outb(txandrx ? 0x03 : 0x02, data->sbase + WBCIR_REG_SP3_IRCR2); 960 961 /* Disable CRC */ 962 wbcir_select_bank(data, WBCIR_BANK_6); 963 outb(0x20, data->sbase + WBCIR_REG_SP3_IRCR3); 964 965 /* Set RX demodulation freq, not really used */ 966 wbcir_select_bank(data, WBCIR_BANK_7); 967 outb(0xF2, data->sbase + WBCIR_REG_SP3_IRRXDC); 968 969 /* Set TX modulation, 36kHz, 7us pulse width */ 970 outb(0x69, data->sbase + WBCIR_REG_SP3_IRTXMC); 971 data->txcarrier = 36000; 972 973 /* Set invert and pin direction */ 974 if (invert) 975 outb(0x10, data->sbase + WBCIR_REG_SP3_IRCFG4); 976 else 977 outb(0x00, data->sbase + WBCIR_REG_SP3_IRCFG4); 978 979 /* Set FIFO thresholds (RX = 8, TX = 3), reset RX/TX */ 980 wbcir_select_bank(data, WBCIR_BANK_0); 981 outb(0x97, data->sbase + WBCIR_REG_SP3_FCR); 982 983 /* Clear AUX status bits */ 984 outb(0xE0, data->sbase + WBCIR_REG_SP3_ASCR); 985 986 /* Clear RX state */ 987 data->rxstate = WBCIR_RXSTATE_INACTIVE; 988 ir_raw_event_reset(data->dev); 989 ir_raw_event_set_idle(data->dev, true); 990 991 /* Clear TX state */ 992 if (data->txstate == WBCIR_TXSTATE_ACTIVE) { 993 kfree(data->txbuf); 994 data->txbuf = NULL; 995 data->txstate = WBCIR_TXSTATE_INACTIVE; 996 } 997 998 /* Enable interrupts */ 999 wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR); 1000 } 1001 1002 static int 1003 wbcir_resume(struct pnp_dev *device) 1004 { 1005 struct wbcir_data *data = pnp_get_drvdata(device); 1006 1007 wbcir_init_hw(data); 1008 enable_irq(data->irq); 1009 led_classdev_resume(&data->led); 1010 1011 return 0; 1012 } 1013 1014 static int 1015 wbcir_probe(struct pnp_dev *device, const struct pnp_device_id *dev_id) 1016 { 1017 struct device *dev = &device->dev; 1018 struct wbcir_data *data; 1019 int err; 1020 1021 if (!(pnp_port_len(device, 0) == EHFUNC_IOMEM_LEN && 1022 pnp_port_len(device, 1) == WAKEUP_IOMEM_LEN && 1023 pnp_port_len(device, 2) == SP_IOMEM_LEN)) { 1024 dev_err(dev, "Invalid resources\n"); 1025 return -ENODEV; 1026 } 1027 1028 data = kzalloc(sizeof(*data), GFP_KERNEL); 1029 if (!data) { 1030 err = -ENOMEM; 1031 goto exit; 1032 } 1033 1034 pnp_set_drvdata(device, data); 1035 1036 spin_lock_init(&data->spinlock); 1037 data->ebase = pnp_port_start(device, 0); 1038 data->wbase = pnp_port_start(device, 1); 1039 data->sbase = pnp_port_start(device, 2); 1040 data->irq = pnp_irq(device, 0); 1041 1042 if (data->wbase == 0 || data->ebase == 0 || 1043 data->sbase == 0 || data->irq == 0) { 1044 err = -ENODEV; 1045 dev_err(dev, "Invalid resources\n"); 1046 goto exit_free_data; 1047 } 1048 1049 dev_dbg(&device->dev, "Found device " 1050 "(w: 0x%lX, e: 0x%lX, s: 0x%lX, i: %u)\n", 1051 data->wbase, data->ebase, data->sbase, data->irq); 1052 1053 data->led.name = "cir::activity"; 1054 data->led.default_trigger = "rc-feedback"; 1055 data->led.brightness_set = wbcir_led_brightness_set; 1056 data->led.brightness_get = wbcir_led_brightness_get; 1057 err = led_classdev_register(&device->dev, &data->led); 1058 if (err) 1059 goto exit_free_data; 1060 1061 data->dev = rc_allocate_device(); 1062 if (!data->dev) { 1063 err = -ENOMEM; 1064 goto exit_unregister_led; 1065 } 1066 1067 data->dev->driver_type = RC_DRIVER_IR_RAW; 1068 data->dev->driver_name = DRVNAME; 1069 data->dev->input_name = WBCIR_NAME; 1070 data->dev->input_phys = "wbcir/cir0"; 1071 data->dev->input_id.bustype = BUS_HOST; 1072 data->dev->input_id.vendor = PCI_VENDOR_ID_WINBOND; 1073 data->dev->input_id.product = WBCIR_ID_FAMILY; 1074 data->dev->input_id.version = WBCIR_ID_CHIP; 1075 data->dev->map_name = RC_MAP_RC6_MCE; 1076 data->dev->s_idle = wbcir_idle_rx; 1077 data->dev->s_carrier_report = wbcir_set_carrier_report; 1078 data->dev->s_tx_mask = wbcir_txmask; 1079 data->dev->s_tx_carrier = wbcir_txcarrier; 1080 data->dev->tx_ir = wbcir_tx; 1081 data->dev->priv = data; 1082 data->dev->dev.parent = &device->dev; 1083 data->dev->timeout = MS_TO_NS(100); 1084 data->dev->rx_resolution = US_TO_NS(2); 1085 data->dev->allowed_protos = RC_BIT_ALL; 1086 1087 err = rc_register_device(data->dev); 1088 if (err) 1089 goto exit_free_rc; 1090 1091 if (!request_region(data->wbase, WAKEUP_IOMEM_LEN, DRVNAME)) { 1092 dev_err(dev, "Region 0x%lx-0x%lx already in use!\n", 1093 data->wbase, data->wbase + WAKEUP_IOMEM_LEN - 1); 1094 err = -EBUSY; 1095 goto exit_unregister_device; 1096 } 1097 1098 if (!request_region(data->ebase, EHFUNC_IOMEM_LEN, DRVNAME)) { 1099 dev_err(dev, "Region 0x%lx-0x%lx already in use!\n", 1100 data->ebase, data->ebase + EHFUNC_IOMEM_LEN - 1); 1101 err = -EBUSY; 1102 goto exit_release_wbase; 1103 } 1104 1105 if (!request_region(data->sbase, SP_IOMEM_LEN, DRVNAME)) { 1106 dev_err(dev, "Region 0x%lx-0x%lx already in use!\n", 1107 data->sbase, data->sbase + SP_IOMEM_LEN - 1); 1108 err = -EBUSY; 1109 goto exit_release_ebase; 1110 } 1111 1112 err = request_irq(data->irq, wbcir_irq_handler, 1113 0, DRVNAME, device); 1114 if (err) { 1115 dev_err(dev, "Failed to claim IRQ %u\n", data->irq); 1116 err = -EBUSY; 1117 goto exit_release_sbase; 1118 } 1119 1120 device_init_wakeup(&device->dev, 1); 1121 1122 wbcir_init_hw(data); 1123 1124 return 0; 1125 1126 exit_release_sbase: 1127 release_region(data->sbase, SP_IOMEM_LEN); 1128 exit_release_ebase: 1129 release_region(data->ebase, EHFUNC_IOMEM_LEN); 1130 exit_release_wbase: 1131 release_region(data->wbase, WAKEUP_IOMEM_LEN); 1132 exit_unregister_device: 1133 rc_unregister_device(data->dev); 1134 data->dev = NULL; 1135 exit_free_rc: 1136 rc_free_device(data->dev); 1137 exit_unregister_led: 1138 led_classdev_unregister(&data->led); 1139 exit_free_data: 1140 kfree(data); 1141 pnp_set_drvdata(device, NULL); 1142 exit: 1143 return err; 1144 } 1145 1146 static void 1147 wbcir_remove(struct pnp_dev *device) 1148 { 1149 struct wbcir_data *data = pnp_get_drvdata(device); 1150 1151 /* Disable interrupts */ 1152 wbcir_set_irqmask(data, WBCIR_IRQ_NONE); 1153 free_irq(data->irq, device); 1154 1155 /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */ 1156 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17); 1157 1158 /* Clear CEIR_EN */ 1159 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01); 1160 1161 /* Clear BUFF_EN, END_EN, MATCH_EN */ 1162 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); 1163 1164 rc_unregister_device(data->dev); 1165 1166 led_classdev_unregister(&data->led); 1167 1168 /* This is ok since &data->led isn't actually used */ 1169 wbcir_led_brightness_set(&data->led, LED_OFF); 1170 1171 release_region(data->wbase, WAKEUP_IOMEM_LEN); 1172 release_region(data->ebase, EHFUNC_IOMEM_LEN); 1173 release_region(data->sbase, SP_IOMEM_LEN); 1174 1175 kfree(data); 1176 1177 pnp_set_drvdata(device, NULL); 1178 } 1179 1180 static const struct pnp_device_id wbcir_ids[] = { 1181 { "WEC1022", 0 }, 1182 { "", 0 } 1183 }; 1184 MODULE_DEVICE_TABLE(pnp, wbcir_ids); 1185 1186 static struct pnp_driver wbcir_driver = { 1187 .name = WBCIR_NAME, 1188 .id_table = wbcir_ids, 1189 .probe = wbcir_probe, 1190 .remove = wbcir_remove, 1191 .suspend = wbcir_suspend, 1192 .resume = wbcir_resume, 1193 .shutdown = wbcir_shutdown 1194 }; 1195 1196 static int __init 1197 wbcir_init(void) 1198 { 1199 int ret; 1200 1201 switch (protocol) { 1202 case IR_PROTOCOL_RC5: 1203 case IR_PROTOCOL_NEC: 1204 case IR_PROTOCOL_RC6: 1205 break; 1206 default: 1207 pr_err("Invalid power-on protocol\n"); 1208 } 1209 1210 ret = pnp_register_driver(&wbcir_driver); 1211 if (ret) 1212 pr_err("Unable to register driver\n"); 1213 1214 return ret; 1215 } 1216 1217 static void __exit 1218 wbcir_exit(void) 1219 { 1220 pnp_unregister_driver(&wbcir_driver); 1221 } 1222 1223 module_init(wbcir_init); 1224 module_exit(wbcir_exit); 1225 1226 MODULE_AUTHOR("David Härdeman <david@hardeman.nu>"); 1227 MODULE_DESCRIPTION("Winbond SuperI/O Consumer IR Driver"); 1228 MODULE_LICENSE("GPL"); 1229