1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * serial_ir.c
4 *
5 * serial_ir - Device driver that records pulse- and pause-lengths
6 * (space-lengths) between DDCD event on a serial port.
7 *
8 * Copyright (C) 1996,97 Ralph Metzler <rjkm@thp.uni-koeln.de>
9 * Copyright (C) 1998 Trent Piepho <xyzzy@u.washington.edu>
10 * Copyright (C) 1998 Ben Pfaff <blp@gnu.org>
11 * Copyright (C) 1999 Christoph Bartelmus <lirc@bartelmus.de>
12 * Copyright (C) 2007 Andrei Tanas <andrei@tanas.ca> (suspend/resume support)
13 * Copyright (C) 2016 Sean Young <sean@mess.org> (port to rc-core)
14 */
15
16 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
17
18 #include <linux/module.h>
19 #include <linux/errno.h>
20 #include <linux/interrupt.h>
21 #include <linux/kernel.h>
22 #include <linux/serial_reg.h>
23 #include <linux/types.h>
24 #include <linux/delay.h>
25 #include <linux/platform_device.h>
26 #include <linux/spinlock.h>
27 #include <media/rc-core.h>
28
29 struct serial_ir_hw {
30 int signal_pin;
31 int signal_pin_change;
32 u8 on;
33 u8 off;
34 unsigned set_send_carrier:1;
35 unsigned set_duty_cycle:1;
36 void (*send_pulse)(unsigned int length, ktime_t edge);
37 void (*send_space)(void);
38 spinlock_t lock;
39 };
40
41 #define IR_HOMEBREW 0
42 #define IR_IRDEO 1
43 #define IR_IRDEO_REMOTE 2
44 #define IR_ANIMAX 3
45 #define IR_IGOR 4
46
47 /* module parameters */
48 static int type;
49 static int io;
50 static int irq;
51 static ulong iommap;
52 static int ioshift;
53 static bool softcarrier = true;
54 static bool share_irq;
55 static int sense = -1; /* -1 = auto, 0 = active high, 1 = active low */
56 static bool txsense; /* 0 = active high, 1 = active low */
57
58 /* forward declarations */
59 static void send_pulse_irdeo(unsigned int length, ktime_t edge);
60 static void send_space_irdeo(void);
61 #ifdef CONFIG_IR_SERIAL_TRANSMITTER
62 static void send_pulse_homebrew(unsigned int length, ktime_t edge);
63 static void send_space_homebrew(void);
64 #endif
65
66 static struct serial_ir_hw hardware[] = {
67 [IR_HOMEBREW] = {
68 .lock = __SPIN_LOCK_UNLOCKED(hardware[IR_HOMEBREW].lock),
69 .signal_pin = UART_MSR_DCD,
70 .signal_pin_change = UART_MSR_DDCD,
71 .on = (UART_MCR_RTS | UART_MCR_OUT2 | UART_MCR_DTR),
72 .off = (UART_MCR_RTS | UART_MCR_OUT2),
73 #ifdef CONFIG_IR_SERIAL_TRANSMITTER
74 .send_pulse = send_pulse_homebrew,
75 .send_space = send_space_homebrew,
76 .set_send_carrier = true,
77 .set_duty_cycle = true,
78 #endif
79 },
80
81 [IR_IRDEO] = {
82 .lock = __SPIN_LOCK_UNLOCKED(hardware[IR_IRDEO].lock),
83 .signal_pin = UART_MSR_DSR,
84 .signal_pin_change = UART_MSR_DDSR,
85 .on = UART_MCR_OUT2,
86 .off = (UART_MCR_RTS | UART_MCR_DTR | UART_MCR_OUT2),
87 .send_pulse = send_pulse_irdeo,
88 .send_space = send_space_irdeo,
89 .set_duty_cycle = true,
90 },
91
92 [IR_IRDEO_REMOTE] = {
93 .lock = __SPIN_LOCK_UNLOCKED(hardware[IR_IRDEO_REMOTE].lock),
94 .signal_pin = UART_MSR_DSR,
95 .signal_pin_change = UART_MSR_DDSR,
96 .on = (UART_MCR_RTS | UART_MCR_DTR | UART_MCR_OUT2),
97 .off = (UART_MCR_RTS | UART_MCR_DTR | UART_MCR_OUT2),
98 .send_pulse = send_pulse_irdeo,
99 .send_space = send_space_irdeo,
100 .set_duty_cycle = true,
101 },
102
103 [IR_ANIMAX] = {
104 .lock = __SPIN_LOCK_UNLOCKED(hardware[IR_ANIMAX].lock),
105 .signal_pin = UART_MSR_DCD,
106 .signal_pin_change = UART_MSR_DDCD,
107 .on = 0,
108 .off = (UART_MCR_RTS | UART_MCR_DTR | UART_MCR_OUT2),
109 },
110
111 [IR_IGOR] = {
112 .lock = __SPIN_LOCK_UNLOCKED(hardware[IR_IGOR].lock),
113 .signal_pin = UART_MSR_DSR,
114 .signal_pin_change = UART_MSR_DDSR,
115 .on = (UART_MCR_RTS | UART_MCR_OUT2 | UART_MCR_DTR),
116 .off = (UART_MCR_RTS | UART_MCR_OUT2),
117 #ifdef CONFIG_IR_SERIAL_TRANSMITTER
118 .send_pulse = send_pulse_homebrew,
119 .send_space = send_space_homebrew,
120 .set_send_carrier = true,
121 .set_duty_cycle = true,
122 #endif
123 },
124 };
125
126 #define RS_ISR_PASS_LIMIT 256
127
128 struct serial_ir {
129 ktime_t lastkt;
130 struct rc_dev *rcdev;
131 struct platform_device *pdev;
132 struct timer_list timeout_timer;
133
134 unsigned int carrier;
135 unsigned int duty_cycle;
136 };
137
138 static struct serial_ir serial_ir;
139
140 /* fetch serial input packet (1 byte) from register offset */
sinp(int offset)141 static u8 sinp(int offset)
142 {
143 if (iommap)
144 /* the register is memory-mapped */
145 offset <<= ioshift;
146
147 return inb(io + offset);
148 }
149
150 /* write serial output packet (1 byte) of value to register offset */
soutp(int offset,u8 value)151 static void soutp(int offset, u8 value)
152 {
153 if (iommap)
154 /* the register is memory-mapped */
155 offset <<= ioshift;
156
157 outb(value, io + offset);
158 }
159
on(void)160 static void on(void)
161 {
162 if (txsense)
163 soutp(UART_MCR, hardware[type].off);
164 else
165 soutp(UART_MCR, hardware[type].on);
166 }
167
off(void)168 static void off(void)
169 {
170 if (txsense)
171 soutp(UART_MCR, hardware[type].on);
172 else
173 soutp(UART_MCR, hardware[type].off);
174 }
175
send_pulse_irdeo(unsigned int length,ktime_t target)176 static void send_pulse_irdeo(unsigned int length, ktime_t target)
177 {
178 long rawbits;
179 int i;
180 unsigned char output;
181 unsigned char chunk, shifted;
182
183 /* how many bits have to be sent ? */
184 rawbits = length * 1152 / 10000;
185 if (serial_ir.duty_cycle > 50)
186 chunk = 3;
187 else
188 chunk = 1;
189 for (i = 0, output = 0x7f; rawbits > 0; rawbits -= 3) {
190 shifted = chunk << (i * 3);
191 shifted >>= 1;
192 output &= (~shifted);
193 i++;
194 if (i == 3) {
195 soutp(UART_TX, output);
196 while (!(sinp(UART_LSR) & UART_LSR_THRE))
197 ;
198 output = 0x7f;
199 i = 0;
200 }
201 }
202 if (i != 0) {
203 soutp(UART_TX, output);
204 while (!(sinp(UART_LSR) & UART_LSR_TEMT))
205 ;
206 }
207 }
208
send_space_irdeo(void)209 static void send_space_irdeo(void)
210 {
211 }
212
213 #ifdef CONFIG_IR_SERIAL_TRANSMITTER
send_pulse_homebrew_softcarrier(unsigned int length,ktime_t edge)214 static void send_pulse_homebrew_softcarrier(unsigned int length, ktime_t edge)
215 {
216 ktime_t now, target = ktime_add_us(edge, length);
217 /*
218 * delta should never exceed 4 seconds and on m68k
219 * ndelay(s64) does not compile; so use s32 rather than s64.
220 */
221 s32 delta;
222 unsigned int pulse, space;
223
224 /* Ensure the dividend fits into 32 bit */
225 pulse = DIV_ROUND_CLOSEST(serial_ir.duty_cycle * (NSEC_PER_SEC / 100),
226 serial_ir.carrier);
227 space = DIV_ROUND_CLOSEST((100 - serial_ir.duty_cycle) *
228 (NSEC_PER_SEC / 100), serial_ir.carrier);
229
230 for (;;) {
231 now = ktime_get();
232 if (ktime_compare(now, target) >= 0)
233 break;
234 on();
235 edge = ktime_add_ns(edge, pulse);
236 delta = ktime_to_ns(ktime_sub(edge, now));
237 if (delta > 0)
238 ndelay(delta);
239 now = ktime_get();
240 off();
241 if (ktime_compare(now, target) >= 0)
242 break;
243 edge = ktime_add_ns(edge, space);
244 delta = ktime_to_ns(ktime_sub(edge, now));
245 if (delta > 0)
246 ndelay(delta);
247 }
248 }
249
send_pulse_homebrew(unsigned int length,ktime_t edge)250 static void send_pulse_homebrew(unsigned int length, ktime_t edge)
251 {
252 if (softcarrier)
253 send_pulse_homebrew_softcarrier(length, edge);
254 else
255 on();
256 }
257
send_space_homebrew(void)258 static void send_space_homebrew(void)
259 {
260 off();
261 }
262 #endif
263
frbwrite(unsigned int l,bool is_pulse)264 static void frbwrite(unsigned int l, bool is_pulse)
265 {
266 /* simple noise filter */
267 static unsigned int ptr, pulse, space;
268 struct ir_raw_event ev = {};
269
270 if (ptr > 0 && is_pulse) {
271 pulse += l;
272 if (pulse > 250) {
273 ev.duration = space;
274 ev.pulse = false;
275 ir_raw_event_store_with_filter(serial_ir.rcdev, &ev);
276 ev.duration = pulse;
277 ev.pulse = true;
278 ir_raw_event_store_with_filter(serial_ir.rcdev, &ev);
279 ptr = 0;
280 pulse = 0;
281 }
282 return;
283 }
284 if (!is_pulse) {
285 if (ptr == 0) {
286 if (l > 20000) {
287 space = l;
288 ptr++;
289 return;
290 }
291 } else {
292 if (l > 20000) {
293 space += pulse;
294 if (space > IR_MAX_DURATION)
295 space = IR_MAX_DURATION;
296 space += l;
297 if (space > IR_MAX_DURATION)
298 space = IR_MAX_DURATION;
299 pulse = 0;
300 return;
301 }
302
303 ev.duration = space;
304 ev.pulse = false;
305 ir_raw_event_store_with_filter(serial_ir.rcdev, &ev);
306 ev.duration = pulse;
307 ev.pulse = true;
308 ir_raw_event_store_with_filter(serial_ir.rcdev, &ev);
309 ptr = 0;
310 pulse = 0;
311 }
312 }
313
314 ev.duration = l;
315 ev.pulse = is_pulse;
316 ir_raw_event_store_with_filter(serial_ir.rcdev, &ev);
317 }
318
serial_ir_irq_handler(int i,void * blah)319 static irqreturn_t serial_ir_irq_handler(int i, void *blah)
320 {
321 ktime_t kt;
322 int counter, dcd;
323 u8 status;
324 ktime_t delkt;
325 unsigned int data;
326 static int last_dcd = -1;
327
328 if ((sinp(UART_IIR) & UART_IIR_NO_INT)) {
329 /* not our interrupt */
330 return IRQ_NONE;
331 }
332
333 counter = 0;
334 do {
335 counter++;
336 status = sinp(UART_MSR);
337 if (counter > RS_ISR_PASS_LIMIT) {
338 dev_err(&serial_ir.pdev->dev, "Trapped in interrupt");
339 break;
340 }
341 if ((status & hardware[type].signal_pin_change) &&
342 sense != -1) {
343 /* get current time */
344 kt = ktime_get();
345
346 /*
347 * The driver needs to know if your receiver is
348 * active high or active low, or the space/pulse
349 * sense could be inverted.
350 */
351
352 /* calc time since last interrupt in nanoseconds */
353 dcd = (status & hardware[type].signal_pin) ? 1 : 0;
354
355 if (dcd == last_dcd) {
356 dev_dbg(&serial_ir.pdev->dev,
357 "ignoring spike: %d %d %lldns %lldns\n",
358 dcd, sense, ktime_to_ns(kt),
359 ktime_to_ns(serial_ir.lastkt));
360 continue;
361 }
362
363 delkt = ktime_sub(kt, serial_ir.lastkt);
364 if (ktime_compare(delkt, ktime_set(15, 0)) > 0) {
365 data = IR_MAX_DURATION; /* really long time */
366 if (!(dcd ^ sense)) {
367 /* sanity check */
368 dev_err(&serial_ir.pdev->dev,
369 "dcd unexpected: %d %d %lldns %lldns\n",
370 dcd, sense, ktime_to_ns(kt),
371 ktime_to_ns(serial_ir.lastkt));
372 /*
373 * detecting pulse while this
374 * MUST be a space!
375 */
376 sense = sense ? 0 : 1;
377 }
378 } else {
379 data = ktime_to_us(delkt);
380 }
381 frbwrite(data, !(dcd ^ sense));
382 serial_ir.lastkt = kt;
383 last_dcd = dcd;
384 }
385 } while (!(sinp(UART_IIR) & UART_IIR_NO_INT)); /* still pending ? */
386
387 mod_timer(&serial_ir.timeout_timer,
388 jiffies + usecs_to_jiffies(serial_ir.rcdev->timeout));
389
390 ir_raw_event_handle(serial_ir.rcdev);
391
392 return IRQ_HANDLED;
393 }
394
hardware_init_port(void)395 static int hardware_init_port(void)
396 {
397 u8 scratch, scratch2, scratch3;
398
399 /*
400 * This is a simple port existence test, borrowed from the autoconfig
401 * function in drivers/tty/serial/8250/8250_port.c
402 */
403 scratch = sinp(UART_IER);
404 soutp(UART_IER, 0);
405 #ifdef __i386__
406 outb(0xff, 0x080);
407 #endif
408 scratch2 = sinp(UART_IER) & 0x0f;
409 soutp(UART_IER, 0x0f);
410 #ifdef __i386__
411 outb(0x00, 0x080);
412 #endif
413 scratch3 = sinp(UART_IER) & 0x0f;
414 soutp(UART_IER, scratch);
415 if (scratch2 != 0 || scratch3 != 0x0f) {
416 /* we fail, there's nothing here */
417 pr_err("port existence test failed, cannot continue\n");
418 return -ENODEV;
419 }
420
421 /* Set DLAB 0. */
422 soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB));
423
424 /* First of all, disable all interrupts */
425 soutp(UART_IER, sinp(UART_IER) &
426 (~(UART_IER_MSI | UART_IER_RLSI | UART_IER_THRI | UART_IER_RDI)));
427
428 /* Clear registers. */
429 sinp(UART_LSR);
430 sinp(UART_RX);
431 sinp(UART_IIR);
432 sinp(UART_MSR);
433
434 /* Set line for power source */
435 off();
436
437 /* Clear registers again to be sure. */
438 sinp(UART_LSR);
439 sinp(UART_RX);
440 sinp(UART_IIR);
441 sinp(UART_MSR);
442
443 switch (type) {
444 case IR_IRDEO:
445 case IR_IRDEO_REMOTE:
446 /* setup port to 7N1 @ 115200 Baud */
447 /* 7N1+start = 9 bits at 115200 ~ 3 bits at 38kHz */
448
449 /* Set DLAB 1. */
450 soutp(UART_LCR, sinp(UART_LCR) | UART_LCR_DLAB);
451 /* Set divisor to 1 => 115200 Baud */
452 soutp(UART_DLM, 0);
453 soutp(UART_DLL, 1);
454 /* Set DLAB 0 + 7N1 */
455 soutp(UART_LCR, UART_LCR_WLEN7);
456 /* THR interrupt already disabled at this point */
457 break;
458 default:
459 break;
460 }
461
462 return 0;
463 }
464
serial_ir_timeout(struct timer_list * unused)465 static void serial_ir_timeout(struct timer_list *unused)
466 {
467 struct ir_raw_event ev = {
468 .timeout = true,
469 .duration = serial_ir.rcdev->timeout
470 };
471 ir_raw_event_store_with_filter(serial_ir.rcdev, &ev);
472 ir_raw_event_handle(serial_ir.rcdev);
473 }
474
475 /* Needed by serial_ir_probe() */
476 static int serial_ir_tx(struct rc_dev *dev, unsigned int *txbuf,
477 unsigned int count);
478 static int serial_ir_tx_duty_cycle(struct rc_dev *dev, u32 cycle);
479 static int serial_ir_tx_carrier(struct rc_dev *dev, u32 carrier);
480 static int serial_ir_open(struct rc_dev *rcdev);
481 static void serial_ir_close(struct rc_dev *rcdev);
482
serial_ir_probe(struct platform_device * dev)483 static int serial_ir_probe(struct platform_device *dev)
484 {
485 struct rc_dev *rcdev;
486 int i, nlow, nhigh, result;
487
488 rcdev = devm_rc_allocate_device(&dev->dev, RC_DRIVER_IR_RAW);
489 if (!rcdev)
490 return -ENOMEM;
491
492 if (hardware[type].send_pulse && hardware[type].send_space)
493 rcdev->tx_ir = serial_ir_tx;
494 if (hardware[type].set_send_carrier)
495 rcdev->s_tx_carrier = serial_ir_tx_carrier;
496 if (hardware[type].set_duty_cycle)
497 rcdev->s_tx_duty_cycle = serial_ir_tx_duty_cycle;
498
499 switch (type) {
500 case IR_HOMEBREW:
501 rcdev->device_name = "Serial IR type home-brew";
502 break;
503 case IR_IRDEO:
504 rcdev->device_name = "Serial IR type IRdeo";
505 break;
506 case IR_IRDEO_REMOTE:
507 rcdev->device_name = "Serial IR type IRdeo remote";
508 break;
509 case IR_ANIMAX:
510 rcdev->device_name = "Serial IR type AnimaX";
511 break;
512 case IR_IGOR:
513 rcdev->device_name = "Serial IR type IgorPlug";
514 break;
515 }
516
517 rcdev->input_phys = KBUILD_MODNAME "/input0";
518 rcdev->input_id.bustype = BUS_HOST;
519 rcdev->input_id.vendor = 0x0001;
520 rcdev->input_id.product = 0x0001;
521 rcdev->input_id.version = 0x0100;
522 rcdev->open = serial_ir_open;
523 rcdev->close = serial_ir_close;
524 rcdev->dev.parent = &serial_ir.pdev->dev;
525 rcdev->allowed_protocols = RC_PROTO_BIT_ALL_IR_DECODER;
526 rcdev->driver_name = KBUILD_MODNAME;
527 rcdev->map_name = RC_MAP_RC6_MCE;
528 rcdev->min_timeout = 1;
529 rcdev->timeout = IR_DEFAULT_TIMEOUT;
530 rcdev->max_timeout = 10 * IR_DEFAULT_TIMEOUT;
531 rcdev->rx_resolution = 250;
532
533 serial_ir.rcdev = rcdev;
534
535 timer_setup(&serial_ir.timeout_timer, serial_ir_timeout, 0);
536
537 result = devm_request_irq(&dev->dev, irq, serial_ir_irq_handler,
538 share_irq ? IRQF_SHARED : 0,
539 KBUILD_MODNAME, &hardware);
540 if (result < 0) {
541 if (result == -EBUSY)
542 dev_err(&dev->dev, "IRQ %d busy\n", irq);
543 else if (result == -EINVAL)
544 dev_err(&dev->dev, "Bad irq number or handler\n");
545 return result;
546 }
547
548 /* Reserve io region. */
549 if ((iommap &&
550 (devm_request_mem_region(&dev->dev, iommap, 8UL << ioshift,
551 KBUILD_MODNAME) == NULL)) ||
552 (!iommap && (devm_request_region(&dev->dev, io, 8,
553 KBUILD_MODNAME) == NULL))) {
554 dev_err(&dev->dev, "port %04x already in use\n", io);
555 dev_warn(&dev->dev, "use 'setserial /dev/ttySX uart none'\n");
556 dev_warn(&dev->dev,
557 "or compile the serial port driver as module and\n");
558 dev_warn(&dev->dev, "make sure this module is loaded first\n");
559 return -EBUSY;
560 }
561
562 result = hardware_init_port();
563 if (result < 0)
564 return result;
565
566 /* Initialize pulse/space widths */
567 serial_ir.duty_cycle = 50;
568 serial_ir.carrier = 38000;
569
570 /* If pin is high, then this must be an active low receiver. */
571 if (sense == -1) {
572 /* wait 1/2 sec for the power supply */
573 msleep(500);
574
575 /*
576 * probe 9 times every 0.04s, collect "votes" for
577 * active high/low
578 */
579 nlow = 0;
580 nhigh = 0;
581 for (i = 0; i < 9; i++) {
582 if (sinp(UART_MSR) & hardware[type].signal_pin)
583 nlow++;
584 else
585 nhigh++;
586 msleep(40);
587 }
588 sense = nlow >= nhigh ? 1 : 0;
589 dev_info(&dev->dev, "auto-detected active %s receiver\n",
590 sense ? "low" : "high");
591 } else
592 dev_info(&dev->dev, "Manually using active %s receiver\n",
593 sense ? "low" : "high");
594
595 dev_dbg(&dev->dev, "Interrupt %d, port %04x obtained\n", irq, io);
596
597 return devm_rc_register_device(&dev->dev, rcdev);
598 }
599
serial_ir_open(struct rc_dev * rcdev)600 static int serial_ir_open(struct rc_dev *rcdev)
601 {
602 unsigned long flags;
603
604 /* initialize timestamp */
605 serial_ir.lastkt = ktime_get();
606
607 spin_lock_irqsave(&hardware[type].lock, flags);
608
609 /* Set DLAB 0. */
610 soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB));
611
612 soutp(UART_IER, sinp(UART_IER) | UART_IER_MSI);
613
614 spin_unlock_irqrestore(&hardware[type].lock, flags);
615
616 return 0;
617 }
618
serial_ir_close(struct rc_dev * rcdev)619 static void serial_ir_close(struct rc_dev *rcdev)
620 {
621 unsigned long flags;
622
623 spin_lock_irqsave(&hardware[type].lock, flags);
624
625 /* Set DLAB 0. */
626 soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB));
627
628 /* First of all, disable all interrupts */
629 soutp(UART_IER, sinp(UART_IER) &
630 (~(UART_IER_MSI | UART_IER_RLSI | UART_IER_THRI | UART_IER_RDI)));
631 spin_unlock_irqrestore(&hardware[type].lock, flags);
632 }
633
serial_ir_tx(struct rc_dev * dev,unsigned int * txbuf,unsigned int count)634 static int serial_ir_tx(struct rc_dev *dev, unsigned int *txbuf,
635 unsigned int count)
636 {
637 unsigned long flags;
638 ktime_t edge;
639 s64 delta;
640 int i;
641
642 spin_lock_irqsave(&hardware[type].lock, flags);
643 if (type == IR_IRDEO) {
644 /* DTR, RTS down */
645 on();
646 }
647
648 edge = ktime_get();
649 for (i = 0; i < count; i++) {
650 if (i % 2)
651 hardware[type].send_space();
652 else
653 hardware[type].send_pulse(txbuf[i], edge);
654
655 edge = ktime_add_us(edge, txbuf[i]);
656 delta = ktime_us_delta(edge, ktime_get());
657 if (delta > 25) {
658 spin_unlock_irqrestore(&hardware[type].lock, flags);
659 usleep_range(delta - 25, delta + 25);
660 spin_lock_irqsave(&hardware[type].lock, flags);
661 } else if (delta > 0) {
662 udelay(delta);
663 }
664 }
665 off();
666 spin_unlock_irqrestore(&hardware[type].lock, flags);
667 return count;
668 }
669
serial_ir_tx_duty_cycle(struct rc_dev * dev,u32 cycle)670 static int serial_ir_tx_duty_cycle(struct rc_dev *dev, u32 cycle)
671 {
672 serial_ir.duty_cycle = cycle;
673 return 0;
674 }
675
serial_ir_tx_carrier(struct rc_dev * dev,u32 carrier)676 static int serial_ir_tx_carrier(struct rc_dev *dev, u32 carrier)
677 {
678 if (carrier > 500000 || carrier < 20000)
679 return -EINVAL;
680
681 serial_ir.carrier = carrier;
682 return 0;
683 }
684
serial_ir_suspend(struct platform_device * dev,pm_message_t state)685 static int serial_ir_suspend(struct platform_device *dev,
686 pm_message_t state)
687 {
688 /* Set DLAB 0. */
689 soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB));
690
691 /* Disable all interrupts */
692 soutp(UART_IER, sinp(UART_IER) &
693 (~(UART_IER_MSI | UART_IER_RLSI | UART_IER_THRI | UART_IER_RDI)));
694
695 /* Clear registers. */
696 sinp(UART_LSR);
697 sinp(UART_RX);
698 sinp(UART_IIR);
699 sinp(UART_MSR);
700
701 return 0;
702 }
703
serial_ir_resume(struct platform_device * dev)704 static int serial_ir_resume(struct platform_device *dev)
705 {
706 unsigned long flags;
707 int result;
708
709 result = hardware_init_port();
710 if (result < 0)
711 return result;
712
713 spin_lock_irqsave(&hardware[type].lock, flags);
714 /* Enable Interrupt */
715 serial_ir.lastkt = ktime_get();
716 soutp(UART_IER, sinp(UART_IER) | UART_IER_MSI);
717 off();
718
719 spin_unlock_irqrestore(&hardware[type].lock, flags);
720
721 return 0;
722 }
723
724 static struct platform_driver serial_ir_driver = {
725 .probe = serial_ir_probe,
726 .suspend = serial_ir_suspend,
727 .resume = serial_ir_resume,
728 .driver = {
729 .name = "serial_ir",
730 },
731 };
732
serial_ir_init(void)733 static int __init serial_ir_init(void)
734 {
735 int result;
736
737 result = platform_driver_register(&serial_ir_driver);
738 if (result)
739 return result;
740
741 serial_ir.pdev = platform_device_alloc("serial_ir", 0);
742 if (!serial_ir.pdev) {
743 result = -ENOMEM;
744 goto exit_driver_unregister;
745 }
746
747 result = platform_device_add(serial_ir.pdev);
748 if (result)
749 goto exit_device_put;
750
751 return 0;
752
753 exit_device_put:
754 platform_device_put(serial_ir.pdev);
755 exit_driver_unregister:
756 platform_driver_unregister(&serial_ir_driver);
757 return result;
758 }
759
serial_ir_exit(void)760 static void serial_ir_exit(void)
761 {
762 platform_device_unregister(serial_ir.pdev);
763 platform_driver_unregister(&serial_ir_driver);
764 }
765
serial_ir_init_module(void)766 static int __init serial_ir_init_module(void)
767 {
768 switch (type) {
769 case IR_HOMEBREW:
770 case IR_IRDEO:
771 case IR_IRDEO_REMOTE:
772 case IR_ANIMAX:
773 case IR_IGOR:
774 /* if nothing specified, use ttyS0/com1 and irq 4 */
775 io = io ? io : 0x3f8;
776 irq = irq ? irq : 4;
777 break;
778 default:
779 return -EINVAL;
780 }
781 if (!softcarrier) {
782 switch (type) {
783 case IR_HOMEBREW:
784 case IR_IGOR:
785 hardware[type].set_send_carrier = false;
786 hardware[type].set_duty_cycle = false;
787 break;
788 }
789 }
790
791 /* make sure sense is either -1, 0, or 1 */
792 if (sense != -1)
793 sense = !!sense;
794
795 return serial_ir_init();
796 }
797
serial_ir_exit_module(void)798 static void __exit serial_ir_exit_module(void)
799 {
800 del_timer_sync(&serial_ir.timeout_timer);
801 serial_ir_exit();
802 }
803
804 module_init(serial_ir_init_module);
805 module_exit(serial_ir_exit_module);
806
807 MODULE_DESCRIPTION("Infra-red receiver driver for serial ports.");
808 MODULE_AUTHOR("Ralph Metzler, Trent Piepho, Ben Pfaff, Christoph Bartelmus, Andrei Tanas");
809 MODULE_LICENSE("GPL");
810
811 module_param(type, int, 0444);
812 MODULE_PARM_DESC(type, "Hardware type (0 = home-brew, 1 = IRdeo, 2 = IRdeo Remote, 3 = AnimaX, 4 = IgorPlug");
813
814 module_param_hw(io, int, ioport, 0444);
815 MODULE_PARM_DESC(io, "I/O address base (0x3f8 or 0x2f8)");
816
817 /* some architectures (e.g. intel xscale) have memory mapped registers */
818 module_param_hw(iommap, ulong, other, 0444);
819 MODULE_PARM_DESC(iommap, "physical base for memory mapped I/O (0 = no memory mapped io)");
820
821 /*
822 * some architectures (e.g. intel xscale) align the 8bit serial registers
823 * on 32bit word boundaries.
824 * See linux-kernel/drivers/tty/serial/8250/8250.c serial_in()/out()
825 */
826 module_param_hw(ioshift, int, other, 0444);
827 MODULE_PARM_DESC(ioshift, "shift I/O register offset (0 = no shift)");
828
829 module_param_hw(irq, int, irq, 0444);
830 MODULE_PARM_DESC(irq, "Interrupt (4 or 3)");
831
832 module_param_hw(share_irq, bool, other, 0444);
833 MODULE_PARM_DESC(share_irq, "Share interrupts (0 = off, 1 = on)");
834
835 module_param(sense, int, 0444);
836 MODULE_PARM_DESC(sense, "Override autodetection of IR receiver circuit (0 = active high, 1 = active low )");
837
838 #ifdef CONFIG_IR_SERIAL_TRANSMITTER
839 module_param(txsense, bool, 0444);
840 MODULE_PARM_DESC(txsense, "Sense of transmitter circuit (0 = active high, 1 = active low )");
841 #endif
842
843 module_param(softcarrier, bool, 0444);
844 MODULE_PARM_DESC(softcarrier, "Software carrier (0 = off, 1 = on, default on)");
845