1 /* 2 * USB RedRat3 IR Transceiver rc-core driver 3 * 4 * Copyright (c) 2011 by Jarod Wilson <jarod@redhat.com> 5 * based heavily on the work of Stephen Cox, with additional 6 * help from RedRat Ltd. 7 * 8 * This driver began life based an an old version of the first-generation 9 * lirc_mceusb driver from the lirc 0.7.2 distribution. It was then 10 * significantly rewritten by Stephen Cox with the aid of RedRat Ltd's 11 * Chris Dodge. 12 * 13 * The driver was then ported to rc-core and significantly rewritten again, 14 * by Jarod, using the in-kernel mceusb driver as a guide, after an initial 15 * port effort was started by Stephen. 16 * 17 * TODO LIST: 18 * - fix lirc not showing repeats properly 19 * -- 20 * 21 * The RedRat3 is a USB transceiver with both send & receive, 22 * with 2 separate sensors available for receive to enable 23 * both good long range reception for general use, and good 24 * short range reception when required for learning a signal. 25 * 26 * http://www.redrat.co.uk/ 27 * 28 * It uses its own little protocol to communicate, the required 29 * parts of which are embedded within this driver. 30 * -- 31 * 32 * This program is free software; you can redistribute it and/or modify 33 * it under the terms of the GNU General Public License as published by 34 * the Free Software Foundation; either version 2 of the License, or 35 * (at your option) any later version. 36 * 37 * This program is distributed in the hope that it will be useful, 38 * but WITHOUT ANY WARRANTY; without even the implied warranty of 39 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 40 * GNU General Public License for more details. 41 * 42 */ 43 44 #include <asm/unaligned.h> 45 #include <linux/device.h> 46 #include <linux/leds.h> 47 #include <linux/module.h> 48 #include <linux/slab.h> 49 #include <linux/usb.h> 50 #include <linux/usb/input.h> 51 #include <media/rc-core.h> 52 53 /* Driver Information */ 54 #define DRIVER_AUTHOR "Jarod Wilson <jarod@redhat.com>" 55 #define DRIVER_AUTHOR2 "The Dweller, Stephen Cox" 56 #define DRIVER_DESC "RedRat3 USB IR Transceiver Driver" 57 #define DRIVER_NAME "redrat3" 58 59 /* bulk data transfer types */ 60 #define RR3_ERROR 0x01 61 #define RR3_MOD_SIGNAL_IN 0x20 62 #define RR3_MOD_SIGNAL_OUT 0x21 63 64 /* Get the RR firmware version */ 65 #define RR3_FW_VERSION 0xb1 66 #define RR3_FW_VERSION_LEN 64 67 /* Send encoded signal bulk-sent earlier*/ 68 #define RR3_TX_SEND_SIGNAL 0xb3 69 #define RR3_SET_IR_PARAM 0xb7 70 #define RR3_GET_IR_PARAM 0xb8 71 /* Blink the red LED on the device */ 72 #define RR3_BLINK_LED 0xb9 73 /* Read serial number of device */ 74 #define RR3_READ_SER_NO 0xba 75 #define RR3_SER_NO_LEN 4 76 /* Start capture with the RC receiver */ 77 #define RR3_RC_DET_ENABLE 0xbb 78 /* Stop capture with the RC receiver */ 79 #define RR3_RC_DET_DISABLE 0xbc 80 /* Start capture with the wideband receiver */ 81 #define RR3_MODSIG_CAPTURE 0xb2 82 /* Return the status of RC detector capture */ 83 #define RR3_RC_DET_STATUS 0xbd 84 /* Reset redrat */ 85 #define RR3_RESET 0xa0 86 87 /* Max number of lengths in the signal. */ 88 #define RR3_IR_IO_MAX_LENGTHS 0x01 89 /* Periods to measure mod. freq. */ 90 #define RR3_IR_IO_PERIODS_MF 0x02 91 /* Size of memory for main signal data */ 92 #define RR3_IR_IO_SIG_MEM_SIZE 0x03 93 /* Delta value when measuring lengths */ 94 #define RR3_IR_IO_LENGTH_FUZZ 0x04 95 /* Timeout for end of signal detection */ 96 #define RR3_IR_IO_SIG_TIMEOUT 0x05 97 /* Minimum value for pause recognition. */ 98 #define RR3_IR_IO_MIN_PAUSE 0x06 99 100 /* Clock freq. of EZ-USB chip */ 101 #define RR3_CLK 24000000 102 /* Clock periods per timer count */ 103 #define RR3_CLK_PER_COUNT 12 104 /* (RR3_CLK / RR3_CLK_PER_COUNT) */ 105 #define RR3_CLK_CONV_FACTOR 2000000 106 /* USB bulk-in wideband IR data endpoint address */ 107 #define RR3_WIDE_IN_EP_ADDR 0x81 108 /* USB bulk-in narrowband IR data endpoint address */ 109 #define RR3_NARROW_IN_EP_ADDR 0x82 110 111 /* Size of the fixed-length portion of the signal */ 112 #define RR3_DRIVER_MAXLENS 255 113 #define RR3_MAX_SIG_SIZE 512 114 #define RR3_TIME_UNIT 50 115 #define RR3_END_OF_SIGNAL 0x7f 116 #define RR3_TX_TRAILER_LEN 2 117 #define RR3_RX_MIN_TIMEOUT 5 118 #define RR3_RX_MAX_TIMEOUT 2000 119 120 /* The 8051's CPUCS Register address */ 121 #define RR3_CPUCS_REG_ADDR 0x7f92 122 123 #define USB_RR3USB_VENDOR_ID 0x112a 124 #define USB_RR3USB_PRODUCT_ID 0x0001 125 #define USB_RR3IIUSB_PRODUCT_ID 0x0005 126 127 128 /* 129 * The redrat3 encodes an IR signal as set of different lengths and a set 130 * of indices into those lengths. This sets how much two lengths must 131 * differ before they are considered distinct, the value is specified 132 * in microseconds. 133 * Default 5, value 0 to 127. 134 */ 135 static int length_fuzz = 5; 136 module_param(length_fuzz, uint, 0644); 137 MODULE_PARM_DESC(length_fuzz, "Length Fuzz (0-127)"); 138 139 /* 140 * When receiving a continuous ir stream (for example when a user is 141 * holding a button down on a remote), this specifies the minimum size 142 * of a space when the redrat3 sends a irdata packet to the host. Specified 143 * in miliseconds. Default value 18ms. 144 * The value can be between 2 and 30 inclusive. 145 */ 146 static int minimum_pause = 18; 147 module_param(minimum_pause, uint, 0644); 148 MODULE_PARM_DESC(minimum_pause, "Minimum Pause in ms (2-30)"); 149 150 /* 151 * The carrier frequency is measured during the first pulse of the IR 152 * signal. The larger the number of periods used To measure, the more 153 * accurate the result is likely to be, however some signals have short 154 * initial pulses, so in some case it may be necessary to reduce this value. 155 * Default 8, value 1 to 255. 156 */ 157 static int periods_measure_carrier = 8; 158 module_param(periods_measure_carrier, uint, 0644); 159 MODULE_PARM_DESC(periods_measure_carrier, "Number of Periods to Measure Carrier (1-255)"); 160 161 162 struct redrat3_header { 163 __be16 length; 164 __be16 transfer_type; 165 } __packed; 166 167 /* sending and receiving irdata */ 168 struct redrat3_irdata { 169 struct redrat3_header header; 170 __be32 pause; 171 __be16 mod_freq_count; 172 __be16 num_periods; 173 __u8 max_lengths; 174 __u8 no_lengths; 175 __be16 max_sig_size; 176 __be16 sig_size; 177 __u8 no_repeats; 178 __be16 lens[RR3_DRIVER_MAXLENS]; /* not aligned */ 179 __u8 sigdata[RR3_MAX_SIG_SIZE]; 180 } __packed; 181 182 /* firmware errors */ 183 struct redrat3_error { 184 struct redrat3_header header; 185 __be16 fw_error; 186 } __packed; 187 188 /* table of devices that work with this driver */ 189 static struct usb_device_id redrat3_dev_table[] = { 190 /* Original version of the RedRat3 */ 191 {USB_DEVICE(USB_RR3USB_VENDOR_ID, USB_RR3USB_PRODUCT_ID)}, 192 /* Second Version/release of the RedRat3 - RetRat3-II */ 193 {USB_DEVICE(USB_RR3USB_VENDOR_ID, USB_RR3IIUSB_PRODUCT_ID)}, 194 {} /* Terminating entry */ 195 }; 196 197 /* Structure to hold all of our device specific stuff */ 198 struct redrat3_dev { 199 /* core device bits */ 200 struct rc_dev *rc; 201 struct device *dev; 202 203 /* led control */ 204 struct led_classdev led; 205 atomic_t flash; 206 struct usb_ctrlrequest flash_control; 207 struct urb *flash_urb; 208 u8 flash_in_buf; 209 210 /* learning */ 211 bool wideband; 212 struct usb_ctrlrequest learn_control; 213 struct urb *learn_urb; 214 u8 learn_buf; 215 216 /* save off the usb device pointer */ 217 struct usb_device *udev; 218 219 /* the receive endpoint */ 220 struct usb_endpoint_descriptor *ep_narrow; 221 /* the buffer to receive data */ 222 void *bulk_in_buf; 223 /* urb used to read ir data */ 224 struct urb *narrow_urb; 225 struct urb *wide_urb; 226 227 /* the send endpoint */ 228 struct usb_endpoint_descriptor *ep_out; 229 230 /* usb dma */ 231 dma_addr_t dma_in; 232 233 /* Is the device currently transmitting?*/ 234 bool transmitting; 235 236 /* store for current packet */ 237 struct redrat3_irdata irdata; 238 u16 bytes_read; 239 240 u32 carrier; 241 242 char name[64]; 243 char phys[64]; 244 }; 245 246 static void redrat3_dump_fw_error(struct redrat3_dev *rr3, int code) 247 { 248 if (!rr3->transmitting && (code != 0x40)) 249 dev_info(rr3->dev, "fw error code 0x%02x: ", code); 250 251 switch (code) { 252 case 0x00: 253 pr_cont("No Error\n"); 254 break; 255 256 /* Codes 0x20 through 0x2f are IR Firmware Errors */ 257 case 0x20: 258 pr_cont("Initial signal pulse not long enough to measure carrier frequency\n"); 259 break; 260 case 0x21: 261 pr_cont("Not enough length values allocated for signal\n"); 262 break; 263 case 0x22: 264 pr_cont("Not enough memory allocated for signal data\n"); 265 break; 266 case 0x23: 267 pr_cont("Too many signal repeats\n"); 268 break; 269 case 0x28: 270 pr_cont("Insufficient memory available for IR signal data memory allocation\n"); 271 break; 272 case 0x29: 273 pr_cont("Insufficient memory available for IrDa signal data memory allocation\n"); 274 break; 275 276 /* Codes 0x30 through 0x3f are USB Firmware Errors */ 277 case 0x30: 278 pr_cont("Insufficient memory available for bulk transfer structure\n"); 279 break; 280 281 /* 282 * Other error codes... These are primarily errors that can occur in 283 * the control messages sent to the redrat 284 */ 285 case 0x40: 286 if (!rr3->transmitting) 287 pr_cont("Signal capture has been terminated\n"); 288 break; 289 case 0x41: 290 pr_cont("Attempt to set/get and unknown signal I/O algorithm parameter\n"); 291 break; 292 case 0x42: 293 pr_cont("Signal capture already started\n"); 294 break; 295 296 default: 297 pr_cont("Unknown Error\n"); 298 break; 299 } 300 } 301 302 static u32 redrat3_val_to_mod_freq(struct redrat3_irdata *irdata) 303 { 304 u32 mod_freq = 0; 305 u16 mod_freq_count = be16_to_cpu(irdata->mod_freq_count); 306 307 if (mod_freq_count != 0) 308 mod_freq = (RR3_CLK * be16_to_cpu(irdata->num_periods)) / 309 (mod_freq_count * RR3_CLK_PER_COUNT); 310 311 return mod_freq; 312 } 313 314 /* this function scales down the figures for the same result... */ 315 static u32 redrat3_len_to_us(u32 length) 316 { 317 u32 biglen = length * 1000; 318 u32 divisor = (RR3_CLK_CONV_FACTOR) / 1000; 319 u32 result = (u32) (biglen / divisor); 320 321 /* don't allow zero lengths to go back, breaks lirc */ 322 return result ? result : 1; 323 } 324 325 /* 326 * convert us back into redrat3 lengths 327 * 328 * length * 1000 length * 1000000 329 * ------------- = ---------------- = micro 330 * rr3clk / 1000 rr3clk 331 332 * 6 * 2 4 * 3 micro * rr3clk micro * rr3clk / 1000 333 * ----- = 4 ----- = 6 -------------- = len --------------------- 334 * 3 2 1000000 1000 335 */ 336 static u32 redrat3_us_to_len(u32 microsec) 337 { 338 u32 result; 339 u32 divisor; 340 341 microsec = (microsec > IR_MAX_DURATION) ? IR_MAX_DURATION : microsec; 342 divisor = (RR3_CLK_CONV_FACTOR / 1000); 343 result = (u32)(microsec * divisor) / 1000; 344 345 /* don't allow zero lengths to go back, breaks lirc */ 346 return result ? result : 1; 347 } 348 349 static void redrat3_process_ir_data(struct redrat3_dev *rr3) 350 { 351 DEFINE_IR_RAW_EVENT(rawir); 352 struct device *dev; 353 unsigned int i, sig_size, single_len, offset, val; 354 u32 mod_freq; 355 356 dev = rr3->dev; 357 358 mod_freq = redrat3_val_to_mod_freq(&rr3->irdata); 359 dev_dbg(dev, "Got mod_freq of %u\n", mod_freq); 360 if (mod_freq && rr3->wideband) { 361 DEFINE_IR_RAW_EVENT(ev); 362 363 ev.carrier_report = 1; 364 ev.carrier = mod_freq; 365 366 ir_raw_event_store(rr3->rc, &ev); 367 } 368 369 /* process each rr3 encoded byte into an int */ 370 sig_size = be16_to_cpu(rr3->irdata.sig_size); 371 for (i = 0; i < sig_size; i++) { 372 offset = rr3->irdata.sigdata[i]; 373 val = get_unaligned_be16(&rr3->irdata.lens[offset]); 374 single_len = redrat3_len_to_us(val); 375 376 /* we should always get pulse/space/pulse/space samples */ 377 if (i % 2) 378 rawir.pulse = false; 379 else 380 rawir.pulse = true; 381 382 rawir.duration = US_TO_NS(single_len); 383 /* cap the value to IR_MAX_DURATION */ 384 rawir.duration = (rawir.duration > IR_MAX_DURATION) ? 385 IR_MAX_DURATION : rawir.duration; 386 387 dev_dbg(dev, "storing %s with duration %d (i: %d)\n", 388 rawir.pulse ? "pulse" : "space", rawir.duration, i); 389 ir_raw_event_store_with_filter(rr3->rc, &rawir); 390 } 391 392 /* add a trailing space */ 393 rawir.pulse = false; 394 rawir.timeout = true; 395 rawir.duration = rr3->rc->timeout; 396 dev_dbg(dev, "storing trailing timeout with duration %d\n", 397 rawir.duration); 398 ir_raw_event_store_with_filter(rr3->rc, &rawir); 399 400 dev_dbg(dev, "calling ir_raw_event_handle\n"); 401 ir_raw_event_handle(rr3->rc); 402 } 403 404 /* Util fn to send rr3 cmds */ 405 static int redrat3_send_cmd(int cmd, struct redrat3_dev *rr3) 406 { 407 struct usb_device *udev; 408 u8 *data; 409 int res; 410 411 data = kzalloc(sizeof(u8), GFP_KERNEL); 412 if (!data) 413 return -ENOMEM; 414 415 udev = rr3->udev; 416 res = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), cmd, 417 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN, 418 0x0000, 0x0000, data, sizeof(u8), HZ * 10); 419 420 if (res < 0) { 421 dev_err(rr3->dev, "%s: Error sending rr3 cmd res %d, data %d", 422 __func__, res, *data); 423 res = -EIO; 424 } else 425 res = data[0]; 426 427 kfree(data); 428 429 return res; 430 } 431 432 /* Enables the long range detector and starts async receive */ 433 static int redrat3_enable_detector(struct redrat3_dev *rr3) 434 { 435 struct device *dev = rr3->dev; 436 u8 ret; 437 438 ret = redrat3_send_cmd(RR3_RC_DET_ENABLE, rr3); 439 if (ret != 0) 440 dev_dbg(dev, "%s: unexpected ret of %d\n", 441 __func__, ret); 442 443 ret = redrat3_send_cmd(RR3_RC_DET_STATUS, rr3); 444 if (ret != 1) { 445 dev_err(dev, "%s: detector status: %d, should be 1\n", 446 __func__, ret); 447 return -EIO; 448 } 449 450 ret = usb_submit_urb(rr3->narrow_urb, GFP_KERNEL); 451 if (ret) { 452 dev_err(rr3->dev, "narrow band urb failed: %d", ret); 453 return ret; 454 } 455 456 ret = usb_submit_urb(rr3->wide_urb, GFP_KERNEL); 457 if (ret) 458 dev_err(rr3->dev, "wide band urb failed: %d", ret); 459 460 return ret; 461 } 462 463 static inline void redrat3_delete(struct redrat3_dev *rr3, 464 struct usb_device *udev) 465 { 466 usb_kill_urb(rr3->narrow_urb); 467 usb_kill_urb(rr3->wide_urb); 468 usb_kill_urb(rr3->flash_urb); 469 usb_kill_urb(rr3->learn_urb); 470 usb_free_urb(rr3->narrow_urb); 471 usb_free_urb(rr3->wide_urb); 472 usb_free_urb(rr3->flash_urb); 473 usb_free_urb(rr3->learn_urb); 474 usb_free_coherent(udev, le16_to_cpu(rr3->ep_narrow->wMaxPacketSize), 475 rr3->bulk_in_buf, rr3->dma_in); 476 477 kfree(rr3); 478 } 479 480 static u32 redrat3_get_timeout(struct redrat3_dev *rr3) 481 { 482 __be32 *tmp; 483 u32 timeout = MS_TO_US(150); /* a sane default, if things go haywire */ 484 int len, ret, pipe; 485 486 len = sizeof(*tmp); 487 tmp = kzalloc(len, GFP_KERNEL); 488 if (!tmp) 489 return timeout; 490 491 pipe = usb_rcvctrlpipe(rr3->udev, 0); 492 ret = usb_control_msg(rr3->udev, pipe, RR3_GET_IR_PARAM, 493 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN, 494 RR3_IR_IO_SIG_TIMEOUT, 0, tmp, len, HZ * 5); 495 if (ret != len) 496 dev_warn(rr3->dev, "Failed to read timeout from hardware\n"); 497 else { 498 timeout = redrat3_len_to_us(be32_to_cpup(tmp)); 499 500 dev_dbg(rr3->dev, "Got timeout of %d ms\n", timeout / 1000); 501 } 502 503 kfree(tmp); 504 505 return timeout; 506 } 507 508 static int redrat3_set_timeout(struct rc_dev *rc_dev, unsigned int timeoutns) 509 { 510 struct redrat3_dev *rr3 = rc_dev->priv; 511 struct usb_device *udev = rr3->udev; 512 struct device *dev = rr3->dev; 513 __be32 *timeout; 514 int ret; 515 516 timeout = kmalloc(sizeof(*timeout), GFP_KERNEL); 517 if (!timeout) 518 return -ENOMEM; 519 520 *timeout = cpu_to_be32(redrat3_us_to_len(timeoutns / 1000)); 521 ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), RR3_SET_IR_PARAM, 522 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT, 523 RR3_IR_IO_SIG_TIMEOUT, 0, timeout, sizeof(*timeout), 524 HZ * 25); 525 dev_dbg(dev, "set ir parm timeout %d ret 0x%02x\n", 526 be32_to_cpu(*timeout), ret); 527 528 if (ret == sizeof(*timeout)) 529 ret = 0; 530 else if (ret >= 0) 531 ret = -EIO; 532 533 kfree(timeout); 534 535 return ret; 536 } 537 538 static void redrat3_reset(struct redrat3_dev *rr3) 539 { 540 struct usb_device *udev = rr3->udev; 541 struct device *dev = rr3->dev; 542 int rc, rxpipe, txpipe; 543 u8 *val; 544 size_t const len = sizeof(*val); 545 546 rxpipe = usb_rcvctrlpipe(udev, 0); 547 txpipe = usb_sndctrlpipe(udev, 0); 548 549 val = kmalloc(len, GFP_KERNEL); 550 if (!val) 551 return; 552 553 *val = 0x01; 554 rc = usb_control_msg(udev, rxpipe, RR3_RESET, 555 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN, 556 RR3_CPUCS_REG_ADDR, 0, val, len, HZ * 25); 557 dev_dbg(dev, "reset returned 0x%02x\n", rc); 558 559 *val = length_fuzz; 560 rc = usb_control_msg(udev, txpipe, RR3_SET_IR_PARAM, 561 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT, 562 RR3_IR_IO_LENGTH_FUZZ, 0, val, len, HZ * 25); 563 dev_dbg(dev, "set ir parm len fuzz %d rc 0x%02x\n", *val, rc); 564 565 *val = (65536 - (minimum_pause * 2000)) / 256; 566 rc = usb_control_msg(udev, txpipe, RR3_SET_IR_PARAM, 567 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT, 568 RR3_IR_IO_MIN_PAUSE, 0, val, len, HZ * 25); 569 dev_dbg(dev, "set ir parm min pause %d rc 0x%02x\n", *val, rc); 570 571 *val = periods_measure_carrier; 572 rc = usb_control_msg(udev, txpipe, RR3_SET_IR_PARAM, 573 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT, 574 RR3_IR_IO_PERIODS_MF, 0, val, len, HZ * 25); 575 dev_dbg(dev, "set ir parm periods measure carrier %d rc 0x%02x", *val, 576 rc); 577 578 *val = RR3_DRIVER_MAXLENS; 579 rc = usb_control_msg(udev, txpipe, RR3_SET_IR_PARAM, 580 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT, 581 RR3_IR_IO_MAX_LENGTHS, 0, val, len, HZ * 25); 582 dev_dbg(dev, "set ir parm max lens %d rc 0x%02x\n", *val, rc); 583 584 kfree(val); 585 } 586 587 static void redrat3_get_firmware_rev(struct redrat3_dev *rr3) 588 { 589 int rc; 590 char *buffer; 591 592 buffer = kcalloc(RR3_FW_VERSION_LEN + 1, sizeof(*buffer), GFP_KERNEL); 593 if (!buffer) 594 return; 595 596 rc = usb_control_msg(rr3->udev, usb_rcvctrlpipe(rr3->udev, 0), 597 RR3_FW_VERSION, 598 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN, 599 0, 0, buffer, RR3_FW_VERSION_LEN, HZ * 5); 600 601 if (rc >= 0) 602 dev_info(rr3->dev, "Firmware rev: %s", buffer); 603 else 604 dev_err(rr3->dev, "Problem fetching firmware ID\n"); 605 606 kfree(buffer); 607 } 608 609 static void redrat3_read_packet_start(struct redrat3_dev *rr3, unsigned len) 610 { 611 struct redrat3_header *header = rr3->bulk_in_buf; 612 unsigned pktlen, pkttype; 613 614 /* grab the Length and type of transfer */ 615 pktlen = be16_to_cpu(header->length); 616 pkttype = be16_to_cpu(header->transfer_type); 617 618 if (pktlen > sizeof(rr3->irdata)) { 619 dev_warn(rr3->dev, "packet length %u too large\n", pktlen); 620 return; 621 } 622 623 switch (pkttype) { 624 case RR3_ERROR: 625 if (len >= sizeof(struct redrat3_error)) { 626 struct redrat3_error *error = rr3->bulk_in_buf; 627 unsigned fw_error = be16_to_cpu(error->fw_error); 628 redrat3_dump_fw_error(rr3, fw_error); 629 } 630 break; 631 632 case RR3_MOD_SIGNAL_IN: 633 memcpy(&rr3->irdata, rr3->bulk_in_buf, len); 634 rr3->bytes_read = len; 635 dev_dbg(rr3->dev, "bytes_read %d, pktlen %d\n", 636 rr3->bytes_read, pktlen); 637 break; 638 639 default: 640 dev_dbg(rr3->dev, "ignoring packet with type 0x%02x, len of %d, 0x%02x\n", 641 pkttype, len, pktlen); 642 break; 643 } 644 } 645 646 static void redrat3_read_packet_continue(struct redrat3_dev *rr3, unsigned len) 647 { 648 void *irdata = &rr3->irdata; 649 650 if (len + rr3->bytes_read > sizeof(rr3->irdata)) { 651 dev_warn(rr3->dev, "too much data for packet\n"); 652 rr3->bytes_read = 0; 653 return; 654 } 655 656 memcpy(irdata + rr3->bytes_read, rr3->bulk_in_buf, len); 657 658 rr3->bytes_read += len; 659 dev_dbg(rr3->dev, "bytes_read %d, pktlen %d\n", rr3->bytes_read, 660 be16_to_cpu(rr3->irdata.header.length)); 661 } 662 663 /* gather IR data from incoming urb, process it when we have enough */ 664 static int redrat3_get_ir_data(struct redrat3_dev *rr3, unsigned len) 665 { 666 struct device *dev = rr3->dev; 667 unsigned pkttype; 668 int ret = 0; 669 670 if (rr3->bytes_read == 0 && len >= sizeof(struct redrat3_header)) { 671 redrat3_read_packet_start(rr3, len); 672 } else if (rr3->bytes_read != 0) { 673 redrat3_read_packet_continue(rr3, len); 674 } else if (rr3->bytes_read == 0) { 675 dev_err(dev, "error: no packet data read\n"); 676 ret = -ENODATA; 677 goto out; 678 } 679 680 if (rr3->bytes_read < be16_to_cpu(rr3->irdata.header.length) + 681 sizeof(struct redrat3_header)) 682 /* we're still accumulating data */ 683 return 0; 684 685 /* if we get here, we've got IR data to decode */ 686 pkttype = be16_to_cpu(rr3->irdata.header.transfer_type); 687 if (pkttype == RR3_MOD_SIGNAL_IN) 688 redrat3_process_ir_data(rr3); 689 else 690 dev_dbg(dev, "discarding non-signal data packet (type 0x%02x)\n", 691 pkttype); 692 693 out: 694 rr3->bytes_read = 0; 695 return ret; 696 } 697 698 /* callback function from USB when async USB request has completed */ 699 static void redrat3_handle_async(struct urb *urb) 700 { 701 struct redrat3_dev *rr3 = urb->context; 702 int ret; 703 704 switch (urb->status) { 705 case 0: 706 ret = redrat3_get_ir_data(rr3, urb->actual_length); 707 if (!ret && rr3->wideband && !rr3->learn_urb->hcpriv) { 708 ret = usb_submit_urb(rr3->learn_urb, GFP_ATOMIC); 709 if (ret) 710 dev_err(rr3->dev, "Failed to submit learning urb: %d", 711 ret); 712 } 713 714 if (!ret) { 715 /* no error, prepare to read more */ 716 ret = usb_submit_urb(urb, GFP_ATOMIC); 717 if (ret) 718 dev_err(rr3->dev, "Failed to resubmit urb: %d", 719 ret); 720 } 721 break; 722 723 case -ECONNRESET: 724 case -ENOENT: 725 case -ESHUTDOWN: 726 usb_unlink_urb(urb); 727 return; 728 729 case -EPIPE: 730 default: 731 dev_warn(rr3->dev, "Error: urb status = %d\n", urb->status); 732 rr3->bytes_read = 0; 733 break; 734 } 735 } 736 737 static u16 mod_freq_to_val(unsigned int mod_freq) 738 { 739 int mult = 6000000; 740 741 /* Clk used in mod. freq. generation is CLK24/4. */ 742 return 65536 - (mult / mod_freq); 743 } 744 745 static int redrat3_set_tx_carrier(struct rc_dev *rcdev, u32 carrier) 746 { 747 struct redrat3_dev *rr3 = rcdev->priv; 748 struct device *dev = rr3->dev; 749 750 dev_dbg(dev, "Setting modulation frequency to %u", carrier); 751 if (carrier == 0) 752 return -EINVAL; 753 754 rr3->carrier = carrier; 755 756 return 0; 757 } 758 759 static int redrat3_transmit_ir(struct rc_dev *rcdev, unsigned *txbuf, 760 unsigned count) 761 { 762 struct redrat3_dev *rr3 = rcdev->priv; 763 struct device *dev = rr3->dev; 764 struct redrat3_irdata *irdata = NULL; 765 int ret, ret_len; 766 int lencheck, cur_sample_len, pipe; 767 int *sample_lens = NULL; 768 u8 curlencheck = 0; 769 unsigned i, sendbuf_len; 770 771 if (rr3->transmitting) { 772 dev_warn(dev, "%s: transmitter already in use\n", __func__); 773 return -EAGAIN; 774 } 775 776 if (count > RR3_MAX_SIG_SIZE - RR3_TX_TRAILER_LEN) 777 return -EINVAL; 778 779 /* rr3 will disable rc detector on transmit */ 780 rr3->transmitting = true; 781 782 sample_lens = kcalloc(RR3_DRIVER_MAXLENS, 783 sizeof(*sample_lens), 784 GFP_KERNEL); 785 if (!sample_lens) 786 return -ENOMEM; 787 788 irdata = kzalloc(sizeof(*irdata), GFP_KERNEL); 789 if (!irdata) { 790 ret = -ENOMEM; 791 goto out; 792 } 793 794 for (i = 0; i < count; i++) { 795 cur_sample_len = redrat3_us_to_len(txbuf[i]); 796 if (cur_sample_len > 0xffff) { 797 dev_warn(dev, "transmit period of %uus truncated to %uus\n", 798 txbuf[i], redrat3_len_to_us(0xffff)); 799 cur_sample_len = 0xffff; 800 } 801 for (lencheck = 0; lencheck < curlencheck; lencheck++) { 802 if (sample_lens[lencheck] == cur_sample_len) 803 break; 804 } 805 if (lencheck == curlencheck) { 806 dev_dbg(dev, "txbuf[%d]=%u, pos %d, enc %u\n", 807 i, txbuf[i], curlencheck, cur_sample_len); 808 if (curlencheck < RR3_DRIVER_MAXLENS) { 809 /* now convert the value to a proper 810 * rr3 value.. */ 811 sample_lens[curlencheck] = cur_sample_len; 812 put_unaligned_be16(cur_sample_len, 813 &irdata->lens[curlencheck]); 814 curlencheck++; 815 } else { 816 ret = -EINVAL; 817 goto out; 818 } 819 } 820 irdata->sigdata[i] = lencheck; 821 } 822 823 irdata->sigdata[count] = RR3_END_OF_SIGNAL; 824 irdata->sigdata[count + 1] = RR3_END_OF_SIGNAL; 825 826 sendbuf_len = offsetof(struct redrat3_irdata, 827 sigdata[count + RR3_TX_TRAILER_LEN]); 828 /* fill in our packet header */ 829 irdata->header.length = cpu_to_be16(sendbuf_len - 830 sizeof(struct redrat3_header)); 831 irdata->header.transfer_type = cpu_to_be16(RR3_MOD_SIGNAL_OUT); 832 irdata->pause = cpu_to_be32(redrat3_len_to_us(100)); 833 irdata->mod_freq_count = cpu_to_be16(mod_freq_to_val(rr3->carrier)); 834 irdata->no_lengths = curlencheck; 835 irdata->sig_size = cpu_to_be16(count + RR3_TX_TRAILER_LEN); 836 837 pipe = usb_sndbulkpipe(rr3->udev, rr3->ep_out->bEndpointAddress); 838 ret = usb_bulk_msg(rr3->udev, pipe, irdata, 839 sendbuf_len, &ret_len, 10 * HZ); 840 dev_dbg(dev, "sent %d bytes, (ret %d)\n", ret_len, ret); 841 842 /* now tell the hardware to transmit what we sent it */ 843 pipe = usb_rcvctrlpipe(rr3->udev, 0); 844 ret = usb_control_msg(rr3->udev, pipe, RR3_TX_SEND_SIGNAL, 845 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN, 846 0, 0, irdata, 2, HZ * 10); 847 848 if (ret < 0) 849 dev_err(dev, "Error: control msg send failed, rc %d\n", ret); 850 else 851 ret = count; 852 853 out: 854 kfree(irdata); 855 kfree(sample_lens); 856 857 rr3->transmitting = false; 858 /* rr3 re-enables rc detector because it was enabled before */ 859 860 return ret; 861 } 862 863 static void redrat3_brightness_set(struct led_classdev *led_dev, enum 864 led_brightness brightness) 865 { 866 struct redrat3_dev *rr3 = container_of(led_dev, struct redrat3_dev, 867 led); 868 869 if (brightness != LED_OFF && atomic_cmpxchg(&rr3->flash, 0, 1) == 0) { 870 int ret = usb_submit_urb(rr3->flash_urb, GFP_ATOMIC); 871 if (ret != 0) { 872 dev_dbg(rr3->dev, "%s: unexpected ret of %d\n", 873 __func__, ret); 874 atomic_set(&rr3->flash, 0); 875 } 876 } 877 } 878 879 static int redrat3_wideband_receiver(struct rc_dev *rcdev, int enable) 880 { 881 struct redrat3_dev *rr3 = rcdev->priv; 882 int ret = 0; 883 884 rr3->wideband = enable != 0; 885 886 if (enable) { 887 ret = usb_submit_urb(rr3->learn_urb, GFP_KERNEL); 888 if (ret) 889 dev_err(rr3->dev, "Failed to submit learning urb: %d", 890 ret); 891 } 892 893 return ret; 894 } 895 896 static void redrat3_learn_complete(struct urb *urb) 897 { 898 struct redrat3_dev *rr3 = urb->context; 899 900 switch (urb->status) { 901 case 0: 902 break; 903 case -ECONNRESET: 904 case -ENOENT: 905 case -ESHUTDOWN: 906 usb_unlink_urb(urb); 907 return; 908 case -EPIPE: 909 default: 910 dev_err(rr3->dev, "Error: learn urb status = %d", urb->status); 911 break; 912 } 913 } 914 915 static void redrat3_led_complete(struct urb *urb) 916 { 917 struct redrat3_dev *rr3 = urb->context; 918 919 switch (urb->status) { 920 case 0: 921 break; 922 case -ECONNRESET: 923 case -ENOENT: 924 case -ESHUTDOWN: 925 usb_unlink_urb(urb); 926 return; 927 case -EPIPE: 928 default: 929 dev_dbg(rr3->dev, "Error: urb status = %d\n", urb->status); 930 break; 931 } 932 933 rr3->led.brightness = LED_OFF; 934 atomic_dec(&rr3->flash); 935 } 936 937 static struct rc_dev *redrat3_init_rc_dev(struct redrat3_dev *rr3) 938 { 939 struct device *dev = rr3->dev; 940 struct rc_dev *rc; 941 int ret; 942 u16 prod = le16_to_cpu(rr3->udev->descriptor.idProduct); 943 944 rc = rc_allocate_device(RC_DRIVER_IR_RAW); 945 if (!rc) 946 return NULL; 947 948 snprintf(rr3->name, sizeof(rr3->name), 949 "RedRat3%s Infrared Remote Transceiver", 950 prod == USB_RR3IIUSB_PRODUCT_ID ? "-II" : ""); 951 952 usb_make_path(rr3->udev, rr3->phys, sizeof(rr3->phys)); 953 954 rc->device_name = rr3->name; 955 rc->input_phys = rr3->phys; 956 usb_to_input_id(rr3->udev, &rc->input_id); 957 rc->dev.parent = dev; 958 rc->priv = rr3; 959 rc->allowed_protocols = RC_PROTO_BIT_ALL_IR_DECODER; 960 rc->min_timeout = MS_TO_NS(RR3_RX_MIN_TIMEOUT); 961 rc->max_timeout = MS_TO_NS(RR3_RX_MAX_TIMEOUT); 962 rc->timeout = US_TO_NS(redrat3_get_timeout(rr3)); 963 rc->s_timeout = redrat3_set_timeout; 964 rc->tx_ir = redrat3_transmit_ir; 965 rc->s_tx_carrier = redrat3_set_tx_carrier; 966 rc->s_carrier_report = redrat3_wideband_receiver; 967 rc->driver_name = DRIVER_NAME; 968 rc->rx_resolution = US_TO_NS(2); 969 rc->map_name = RC_MAP_HAUPPAUGE; 970 971 ret = rc_register_device(rc); 972 if (ret < 0) { 973 dev_err(dev, "remote dev registration failed\n"); 974 goto out; 975 } 976 977 return rc; 978 979 out: 980 rc_free_device(rc); 981 return NULL; 982 } 983 984 static int redrat3_dev_probe(struct usb_interface *intf, 985 const struct usb_device_id *id) 986 { 987 struct usb_device *udev = interface_to_usbdev(intf); 988 struct device *dev = &intf->dev; 989 struct usb_host_interface *uhi; 990 struct redrat3_dev *rr3; 991 struct usb_endpoint_descriptor *ep; 992 struct usb_endpoint_descriptor *ep_narrow = NULL; 993 struct usb_endpoint_descriptor *ep_wide = NULL; 994 struct usb_endpoint_descriptor *ep_out = NULL; 995 u8 addr, attrs; 996 int pipe, i; 997 int retval = -ENOMEM; 998 999 uhi = intf->cur_altsetting; 1000 1001 /* find our bulk-in and bulk-out endpoints */ 1002 for (i = 0; i < uhi->desc.bNumEndpoints; ++i) { 1003 ep = &uhi->endpoint[i].desc; 1004 addr = ep->bEndpointAddress; 1005 attrs = ep->bmAttributes; 1006 1007 if (((addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) && 1008 ((attrs & USB_ENDPOINT_XFERTYPE_MASK) == 1009 USB_ENDPOINT_XFER_BULK)) { 1010 dev_dbg(dev, "found bulk-in endpoint at 0x%02x\n", 1011 ep->bEndpointAddress); 1012 /* data comes in on 0x82, 0x81 is for learning */ 1013 if (ep->bEndpointAddress == RR3_NARROW_IN_EP_ADDR) 1014 ep_narrow = ep; 1015 if (ep->bEndpointAddress == RR3_WIDE_IN_EP_ADDR) 1016 ep_wide = ep; 1017 } 1018 1019 if ((ep_out == NULL) && 1020 ((addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT) && 1021 ((attrs & USB_ENDPOINT_XFERTYPE_MASK) == 1022 USB_ENDPOINT_XFER_BULK)) { 1023 dev_dbg(dev, "found bulk-out endpoint at 0x%02x\n", 1024 ep->bEndpointAddress); 1025 ep_out = ep; 1026 } 1027 } 1028 1029 if (!ep_narrow || !ep_out || !ep_wide) { 1030 dev_err(dev, "Couldn't find all endpoints\n"); 1031 retval = -ENODEV; 1032 goto no_endpoints; 1033 } 1034 1035 /* allocate memory for our device state and initialize it */ 1036 rr3 = kzalloc(sizeof(*rr3), GFP_KERNEL); 1037 if (!rr3) 1038 goto no_endpoints; 1039 1040 rr3->dev = &intf->dev; 1041 rr3->ep_narrow = ep_narrow; 1042 rr3->ep_out = ep_out; 1043 rr3->udev = udev; 1044 1045 /* set up bulk-in endpoint */ 1046 rr3->narrow_urb = usb_alloc_urb(0, GFP_KERNEL); 1047 if (!rr3->narrow_urb) 1048 goto redrat_free; 1049 1050 rr3->wide_urb = usb_alloc_urb(0, GFP_KERNEL); 1051 if (!rr3->wide_urb) 1052 goto redrat_free; 1053 1054 rr3->bulk_in_buf = usb_alloc_coherent(udev, 1055 le16_to_cpu(ep_narrow->wMaxPacketSize), 1056 GFP_KERNEL, &rr3->dma_in); 1057 if (!rr3->bulk_in_buf) 1058 goto redrat_free; 1059 1060 pipe = usb_rcvbulkpipe(udev, ep_narrow->bEndpointAddress); 1061 usb_fill_bulk_urb(rr3->narrow_urb, udev, pipe, rr3->bulk_in_buf, 1062 le16_to_cpu(ep_narrow->wMaxPacketSize), 1063 redrat3_handle_async, rr3); 1064 rr3->narrow_urb->transfer_dma = rr3->dma_in; 1065 rr3->narrow_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; 1066 1067 pipe = usb_rcvbulkpipe(udev, ep_wide->bEndpointAddress); 1068 usb_fill_bulk_urb(rr3->wide_urb, udev, pipe, rr3->bulk_in_buf, 1069 le16_to_cpu(ep_narrow->wMaxPacketSize), 1070 redrat3_handle_async, rr3); 1071 rr3->wide_urb->transfer_dma = rr3->dma_in; 1072 rr3->wide_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; 1073 1074 redrat3_reset(rr3); 1075 redrat3_get_firmware_rev(rr3); 1076 1077 /* default.. will get overridden by any sends with a freq defined */ 1078 rr3->carrier = 38000; 1079 1080 atomic_set(&rr3->flash, 0); 1081 rr3->flash_urb = usb_alloc_urb(0, GFP_KERNEL); 1082 if (!rr3->flash_urb) 1083 goto redrat_free; 1084 1085 /* learn urb */ 1086 rr3->learn_urb = usb_alloc_urb(0, GFP_KERNEL); 1087 if (!rr3->learn_urb) 1088 goto redrat_free; 1089 1090 /* setup packet is 'c0 b2 0000 0000 0001' */ 1091 rr3->learn_control.bRequestType = 0xc0; 1092 rr3->learn_control.bRequest = RR3_MODSIG_CAPTURE; 1093 rr3->learn_control.wLength = cpu_to_le16(1); 1094 1095 usb_fill_control_urb(rr3->learn_urb, udev, usb_rcvctrlpipe(udev, 0), 1096 (unsigned char *)&rr3->learn_control, 1097 &rr3->learn_buf, sizeof(rr3->learn_buf), 1098 redrat3_learn_complete, rr3); 1099 1100 /* setup packet is 'c0 b9 0000 0000 0001' */ 1101 rr3->flash_control.bRequestType = 0xc0; 1102 rr3->flash_control.bRequest = RR3_BLINK_LED; 1103 rr3->flash_control.wLength = cpu_to_le16(1); 1104 1105 usb_fill_control_urb(rr3->flash_urb, udev, usb_rcvctrlpipe(udev, 0), 1106 (unsigned char *)&rr3->flash_control, 1107 &rr3->flash_in_buf, sizeof(rr3->flash_in_buf), 1108 redrat3_led_complete, rr3); 1109 1110 /* led control */ 1111 rr3->led.name = "redrat3:red:feedback"; 1112 rr3->led.default_trigger = "rc-feedback"; 1113 rr3->led.brightness_set = redrat3_brightness_set; 1114 retval = led_classdev_register(&intf->dev, &rr3->led); 1115 if (retval) 1116 goto redrat_free; 1117 1118 rr3->rc = redrat3_init_rc_dev(rr3); 1119 if (!rr3->rc) { 1120 retval = -ENOMEM; 1121 goto led_free; 1122 } 1123 1124 /* might be all we need to do? */ 1125 retval = redrat3_enable_detector(rr3); 1126 if (retval < 0) 1127 goto led_free; 1128 1129 /* we can register the device now, as it is ready */ 1130 usb_set_intfdata(intf, rr3); 1131 1132 return 0; 1133 1134 led_free: 1135 led_classdev_unregister(&rr3->led); 1136 redrat_free: 1137 redrat3_delete(rr3, rr3->udev); 1138 1139 no_endpoints: 1140 return retval; 1141 } 1142 1143 static void redrat3_dev_disconnect(struct usb_interface *intf) 1144 { 1145 struct usb_device *udev = interface_to_usbdev(intf); 1146 struct redrat3_dev *rr3 = usb_get_intfdata(intf); 1147 1148 usb_set_intfdata(intf, NULL); 1149 rc_unregister_device(rr3->rc); 1150 led_classdev_unregister(&rr3->led); 1151 redrat3_delete(rr3, udev); 1152 } 1153 1154 static int redrat3_dev_suspend(struct usb_interface *intf, pm_message_t message) 1155 { 1156 struct redrat3_dev *rr3 = usb_get_intfdata(intf); 1157 1158 led_classdev_suspend(&rr3->led); 1159 usb_kill_urb(rr3->narrow_urb); 1160 usb_kill_urb(rr3->wide_urb); 1161 usb_kill_urb(rr3->flash_urb); 1162 return 0; 1163 } 1164 1165 static int redrat3_dev_resume(struct usb_interface *intf) 1166 { 1167 struct redrat3_dev *rr3 = usb_get_intfdata(intf); 1168 1169 if (usb_submit_urb(rr3->narrow_urb, GFP_ATOMIC)) 1170 return -EIO; 1171 if (usb_submit_urb(rr3->wide_urb, GFP_ATOMIC)) 1172 return -EIO; 1173 led_classdev_resume(&rr3->led); 1174 return 0; 1175 } 1176 1177 static struct usb_driver redrat3_dev_driver = { 1178 .name = DRIVER_NAME, 1179 .probe = redrat3_dev_probe, 1180 .disconnect = redrat3_dev_disconnect, 1181 .suspend = redrat3_dev_suspend, 1182 .resume = redrat3_dev_resume, 1183 .reset_resume = redrat3_dev_resume, 1184 .id_table = redrat3_dev_table 1185 }; 1186 1187 module_usb_driver(redrat3_dev_driver); 1188 1189 MODULE_DESCRIPTION(DRIVER_DESC); 1190 MODULE_AUTHOR(DRIVER_AUTHOR); 1191 MODULE_AUTHOR(DRIVER_AUTHOR2); 1192 MODULE_LICENSE("GPL"); 1193 MODULE_DEVICE_TABLE(usb, redrat3_dev_table); 1194