1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /* 3 * Driver for ITE Tech Inc. IT8712F/IT8512F CIR 4 * 5 * Copyright (C) 2010 Juan Jesús García de Soria <skandalfo@gmail.com> 6 */ 7 8 /* platform driver name to register */ 9 #define ITE_DRIVER_NAME "ite-cir" 10 11 /* FIFO sizes */ 12 #define ITE_TX_FIFO_LEN 32 13 #define ITE_RX_FIFO_LEN 32 14 15 /* interrupt types */ 16 #define ITE_IRQ_TX_FIFO 1 17 #define ITE_IRQ_RX_FIFO 2 18 #define ITE_IRQ_RX_FIFO_OVERRUN 4 19 20 /* forward declaration */ 21 struct ite_dev; 22 23 /* struct for storing the parameters of different recognized devices */ 24 struct ite_dev_params { 25 /* model of the device */ 26 const char *model; 27 28 /* size of the I/O region */ 29 int io_region_size; 30 31 /* IR pnp I/O resource number */ 32 int io_rsrc_no; 33 34 /* hw-specific operation function pointers; most of these must be 35 * called while holding the spin lock, except for the TX FIFO length 36 * one */ 37 /* get pending interrupt causes */ 38 int (*get_irq_causes) (struct ite_dev *dev); 39 40 /* enable rx */ 41 void (*enable_rx) (struct ite_dev *dev); 42 43 /* make rx enter the idle state; keep listening for a pulse, but stop 44 * streaming space bytes */ 45 void (*idle_rx) (struct ite_dev *dev); 46 47 /* disable rx completely */ 48 void (*disable_rx) (struct ite_dev *dev); 49 50 /* read bytes from RX FIFO; return read count */ 51 int (*get_rx_bytes) (struct ite_dev *dev, u8 *buf, int buf_size); 52 53 /* enable tx FIFO space available interrupt */ 54 void (*enable_tx_interrupt) (struct ite_dev *dev); 55 56 /* disable tx FIFO space available interrupt */ 57 void (*disable_tx_interrupt) (struct ite_dev *dev); 58 59 /* get number of full TX FIFO slots */ 60 int (*get_tx_used_slots) (struct ite_dev *dev); 61 62 /* put a byte to the TX FIFO */ 63 void (*put_tx_byte) (struct ite_dev *dev, u8 value); 64 65 /* disable hardware completely */ 66 void (*disable) (struct ite_dev *dev); 67 68 /* initialize the hardware */ 69 void (*init_hardware) (struct ite_dev *dev); 70 71 /* set the carrier parameters */ 72 void (*set_carrier_params) (struct ite_dev *dev, bool high_freq, 73 bool use_demodulator, u8 carrier_freq_bits, 74 u8 allowance_bits, u8 pulse_width_bits); 75 }; 76 77 /* ITE CIR device structure */ 78 struct ite_dev { 79 struct pnp_dev *pdev; 80 struct rc_dev *rdev; 81 82 /* sync data */ 83 spinlock_t lock; 84 bool transmitting; 85 86 /* transmit support */ 87 wait_queue_head_t tx_queue, tx_ended; 88 89 /* rx low carrier frequency, in Hz, 0 means no demodulation */ 90 unsigned int rx_low_carrier_freq; 91 92 /* tx high carrier frequency, in Hz, 0 means no demodulation */ 93 unsigned int rx_high_carrier_freq; 94 95 /* tx carrier frequency, in Hz */ 96 unsigned int tx_carrier_freq; 97 98 /* duty cycle, 0-100 */ 99 int tx_duty_cycle; 100 101 /* hardware I/O settings */ 102 unsigned long cir_addr; 103 int cir_irq; 104 105 /* overridable copy of model parameters */ 106 const struct ite_dev_params *params; 107 }; 108 109 /* common values for all kinds of hardware */ 110 111 /* baud rate divisor default */ 112 #define ITE_BAUDRATE_DIVISOR 1 113 114 /* low-speed carrier frequency limits (Hz) */ 115 #define ITE_LCF_MIN_CARRIER_FREQ 27000 116 #define ITE_LCF_MAX_CARRIER_FREQ 58000 117 118 /* high-speed carrier frequency limits (Hz) */ 119 #define ITE_HCF_MIN_CARRIER_FREQ 400000 120 #define ITE_HCF_MAX_CARRIER_FREQ 500000 121 122 /* default carrier freq for when demodulator is off (Hz) */ 123 #define ITE_DEFAULT_CARRIER_FREQ 38000 124 125 /* convert bits to us */ 126 #define ITE_BITS_TO_US(bits, sample_period) \ 127 ((u32)((bits) * ITE_BAUDRATE_DIVISOR * (sample_period) / 1000)) 128 129 /* 130 * n in RDCR produces a tolerance of +/- n * 6.25% around the center 131 * carrier frequency... 132 * 133 * From two limit frequencies, L (low) and H (high), we can get both the 134 * center frequency F = (L + H) / 2 and the variation from the center 135 * frequency A = (H - L) / (H + L). We can use this in order to honor the 136 * s_rx_carrier_range() call in ir-core. We'll suppose that any request 137 * setting L=0 means we must shut down the demodulator. 138 */ 139 #define ITE_RXDCR_PER_10000_STEP 625 140 141 /* high speed carrier freq values */ 142 #define ITE_CFQ_400 0x03 143 #define ITE_CFQ_450 0x08 144 #define ITE_CFQ_480 0x0b 145 #define ITE_CFQ_500 0x0d 146 147 /* values for pulse widths */ 148 #define ITE_TXMPW_A 0x02 149 #define ITE_TXMPW_B 0x03 150 #define ITE_TXMPW_C 0x04 151 #define ITE_TXMPW_D 0x05 152 #define ITE_TXMPW_E 0x06 153 154 /* values for demodulator carrier range allowance */ 155 #define ITE_RXDCR_DEFAULT 0x01 /* default carrier range */ 156 #define ITE_RXDCR_MAX 0x07 /* default carrier range */ 157 158 /* DR TX bits */ 159 #define ITE_TX_PULSE 0x00 160 #define ITE_TX_SPACE 0x80 161 #define ITE_TX_MAX_RLE 0x80 162 #define ITE_TX_RLE_MASK 0x7f 163 164 /* 165 * IT8712F 166 * 167 * hardware data obtained from: 168 * 169 * IT8712F 170 * Environment Control - Low Pin Count Input / Output 171 * (EC - LPC I/O) 172 * Preliminary Specification V0. 81 173 */ 174 175 /* register offsets */ 176 #define IT87_DR 0x00 /* data register */ 177 #define IT87_IER 0x01 /* interrupt enable register */ 178 #define IT87_RCR 0x02 /* receiver control register */ 179 #define IT87_TCR1 0x03 /* transmitter control register 1 */ 180 #define IT87_TCR2 0x04 /* transmitter control register 2 */ 181 #define IT87_TSR 0x05 /* transmitter status register */ 182 #define IT87_RSR 0x06 /* receiver status register */ 183 #define IT87_BDLR 0x05 /* baud rate divisor low byte register */ 184 #define IT87_BDHR 0x06 /* baud rate divisor high byte register */ 185 #define IT87_IIR 0x07 /* interrupt identification register */ 186 187 #define IT87_IOREG_LENGTH 0x08 /* length of register file */ 188 189 /* IER bits */ 190 #define IT87_TLDLIE 0x01 /* transmitter low data interrupt enable */ 191 #define IT87_RDAIE 0x02 /* receiver data available interrupt enable */ 192 #define IT87_RFOIE 0x04 /* receiver FIFO overrun interrupt enable */ 193 #define IT87_IEC 0x08 /* interrupt enable control */ 194 #define IT87_BR 0x10 /* baud rate register enable */ 195 #define IT87_RESET 0x20 /* reset */ 196 197 /* RCR bits */ 198 #define IT87_RXDCR 0x07 /* receiver demodulation carrier range mask */ 199 #define IT87_RXACT 0x08 /* receiver active */ 200 #define IT87_RXEND 0x10 /* receiver demodulation enable */ 201 #define IT87_RXEN 0x20 /* receiver enable */ 202 #define IT87_HCFS 0x40 /* high-speed carrier frequency select */ 203 #define IT87_RDWOS 0x80 /* receiver data without sync */ 204 205 /* TCR1 bits */ 206 #define IT87_TXMPM 0x03 /* transmitter modulation pulse mode mask */ 207 #define IT87_TXMPM_DEFAULT 0x00 /* modulation pulse mode default */ 208 #define IT87_TXENDF 0x04 /* transmitter deferral */ 209 #define IT87_TXRLE 0x08 /* transmitter run length enable */ 210 #define IT87_FIFOTL 0x30 /* FIFO level threshold mask */ 211 #define IT87_FIFOTL_DEFAULT 0x20 /* FIFO level threshold default 212 * 0x00 -> 1, 0x10 -> 7, 0x20 -> 17, 213 * 0x30 -> 25 */ 214 #define IT87_ILE 0x40 /* internal loopback enable */ 215 #define IT87_FIFOCLR 0x80 /* FIFO clear bit */ 216 217 /* TCR2 bits */ 218 #define IT87_TXMPW 0x07 /* transmitter modulation pulse width mask */ 219 #define IT87_TXMPW_DEFAULT 0x04 /* default modulation pulse width */ 220 #define IT87_CFQ 0xf8 /* carrier frequency mask */ 221 #define IT87_CFQ_SHIFT 3 /* carrier frequency bit shift */ 222 223 /* TSR bits */ 224 #define IT87_TXFBC 0x3f /* transmitter FIFO byte count mask */ 225 226 /* RSR bits */ 227 #define IT87_RXFBC 0x3f /* receiver FIFO byte count mask */ 228 #define IT87_RXFTO 0x80 /* receiver FIFO time-out */ 229 230 /* IIR bits */ 231 #define IT87_IP 0x01 /* interrupt pending */ 232 #define IT87_II 0x06 /* interrupt identification mask */ 233 #define IT87_II_NOINT 0x00 /* no interrupt */ 234 #define IT87_II_TXLDL 0x02 /* transmitter low data level */ 235 #define IT87_II_RXDS 0x04 /* receiver data stored */ 236 #define IT87_II_RXFO 0x06 /* receiver FIFO overrun */ 237 238 /* 239 * IT8512E/F 240 * 241 * Hardware data obtained from: 242 * 243 * IT8512E/F 244 * Embedded Controller 245 * Preliminary Specification V0.4.1 246 * 247 * Note that the CIR registers are not directly available to the host, because 248 * they only are accessible to the integrated microcontroller. Thus, in order 249 * use it, some kind of bridging is required. As the bridging may depend on 250 * the controller firmware in use, we are going to use the PNP ID in order to 251 * determine the strategy and ports available. See after these generic 252 * IT8512E/F register definitions for register definitions for those 253 * strategies. 254 */ 255 256 /* register offsets */ 257 #define IT85_C0DR 0x00 /* data register */ 258 #define IT85_C0MSTCR 0x01 /* master control register */ 259 #define IT85_C0IER 0x02 /* interrupt enable register */ 260 #define IT85_C0IIR 0x03 /* interrupt identification register */ 261 #define IT85_C0CFR 0x04 /* carrier frequency register */ 262 #define IT85_C0RCR 0x05 /* receiver control register */ 263 #define IT85_C0TCR 0x06 /* transmitter control register */ 264 #define IT85_C0SCK 0x07 /* slow clock control register */ 265 #define IT85_C0BDLR 0x08 /* baud rate divisor low byte register */ 266 #define IT85_C0BDHR 0x09 /* baud rate divisor high byte register */ 267 #define IT85_C0TFSR 0x0a /* transmitter FIFO status register */ 268 #define IT85_C0RFSR 0x0b /* receiver FIFO status register */ 269 #define IT85_C0WCL 0x0d /* wakeup code length register */ 270 #define IT85_C0WCR 0x0e /* wakeup code read/write register */ 271 #define IT85_C0WPS 0x0f /* wakeup power control/status register */ 272 273 #define IT85_IOREG_LENGTH 0x10 /* length of register file */ 274 275 /* C0MSTCR bits */ 276 #define IT85_RESET 0x01 /* reset */ 277 #define IT85_FIFOCLR 0x02 /* FIFO clear bit */ 278 #define IT85_FIFOTL 0x0c /* FIFO level threshold mask */ 279 #define IT85_FIFOTL_DEFAULT 0x08 /* FIFO level threshold default 280 * 0x00 -> 1, 0x04 -> 7, 0x08 -> 17, 281 * 0x0c -> 25 */ 282 #define IT85_ILE 0x10 /* internal loopback enable */ 283 #define IT85_ILSEL 0x20 /* internal loopback select */ 284 285 /* C0IER bits */ 286 #define IT85_TLDLIE 0x01 /* TX low data level interrupt enable */ 287 #define IT85_RDAIE 0x02 /* RX data available interrupt enable */ 288 #define IT85_RFOIE 0x04 /* RX FIFO overrun interrupt enable */ 289 #define IT85_IEC 0x80 /* interrupt enable function control */ 290 291 /* C0IIR bits */ 292 #define IT85_TLDLI 0x01 /* transmitter low data level interrupt */ 293 #define IT85_RDAI 0x02 /* receiver data available interrupt */ 294 #define IT85_RFOI 0x04 /* receiver FIFO overrun interrupt */ 295 #define IT85_NIP 0x80 /* no interrupt pending */ 296 297 /* C0CFR bits */ 298 #define IT85_CFQ 0x1f /* carrier frequency mask */ 299 #define IT85_HCFS 0x20 /* high speed carrier frequency select */ 300 301 /* C0RCR bits */ 302 #define IT85_RXDCR 0x07 /* receiver demodulation carrier range mask */ 303 #define IT85_RXACT 0x08 /* receiver active */ 304 #define IT85_RXEND 0x10 /* receiver demodulation enable */ 305 #define IT85_RDWOS 0x20 /* receiver data without sync */ 306 #define IT85_RXEN 0x80 /* receiver enable */ 307 308 /* C0TCR bits */ 309 #define IT85_TXMPW 0x07 /* transmitter modulation pulse width mask */ 310 #define IT85_TXMPW_DEFAULT 0x04 /* default modulation pulse width */ 311 #define IT85_TXMPM 0x18 /* transmitter modulation pulse mode mask */ 312 #define IT85_TXMPM_DEFAULT 0x00 /* modulation pulse mode default */ 313 #define IT85_TXENDF 0x20 /* transmitter deferral */ 314 #define IT85_TXRLE 0x40 /* transmitter run length enable */ 315 316 /* C0SCK bits */ 317 #define IT85_SCKS 0x01 /* slow clock select */ 318 #define IT85_TXDCKG 0x02 /* TXD clock gating */ 319 #define IT85_DLL1P8E 0x04 /* DLL 1.8432M enable */ 320 #define IT85_DLLTE 0x08 /* DLL test enable */ 321 #define IT85_BRCM 0x70 /* baud rate count mode */ 322 #define IT85_DLLOCK 0x80 /* DLL lock */ 323 324 /* C0TFSR bits */ 325 #define IT85_TXFBC 0x3f /* transmitter FIFO count mask */ 326 327 /* C0RFSR bits */ 328 #define IT85_RXFBC 0x3f /* receiver FIFO count mask */ 329 #define IT85_RXFTO 0x80 /* receiver FIFO time-out */ 330 331 /* C0WCL bits */ 332 #define IT85_WCL 0x3f /* wakeup code length mask */ 333 334 /* C0WPS bits */ 335 #define IT85_CIRPOSIE 0x01 /* power on/off status interrupt enable */ 336 #define IT85_CIRPOIS 0x02 /* power on/off interrupt status */ 337 #define IT85_CIRPOII 0x04 /* power on/off interrupt identification */ 338 #define IT85_RCRST 0x10 /* wakeup code reading counter reset bit */ 339 #define IT85_WCRST 0x20 /* wakeup code writing counter reset bit */ 340 341 /* 342 * ITE8708 343 * 344 * Hardware data obtained from hacked driver for IT8512 in this forum post: 345 * 346 * http://ubuntuforums.org/showthread.php?t=1028640 347 * 348 * Although there's no official documentation for that driver, analysis would 349 * suggest that it maps the 16 registers of IT8512 onto two 8-register banks, 350 * selectable by a single bank-select bit that's mapped onto both banks. The 351 * IT8512 registers are mapped in a different order, so that the first bank 352 * maps the ones that are used more often, and two registers that share a 353 * reserved high-order bit are placed at the same offset in both banks in 354 * order to reuse the reserved bit as the bank select bit. 355 */ 356 357 /* register offsets */ 358 359 /* mapped onto both banks */ 360 #define IT8708_BANKSEL 0x07 /* bank select register */ 361 #define IT8708_HRAE 0x80 /* high registers access enable */ 362 363 /* mapped onto the low bank */ 364 #define IT8708_C0DR 0x00 /* data register */ 365 #define IT8708_C0MSTCR 0x01 /* master control register */ 366 #define IT8708_C0IER 0x02 /* interrupt enable register */ 367 #define IT8708_C0IIR 0x03 /* interrupt identification register */ 368 #define IT8708_C0RFSR 0x04 /* receiver FIFO status register */ 369 #define IT8708_C0RCR 0x05 /* receiver control register */ 370 #define IT8708_C0TFSR 0x06 /* transmitter FIFO status register */ 371 #define IT8708_C0TCR 0x07 /* transmitter control register */ 372 373 /* mapped onto the high bank */ 374 #define IT8708_C0BDLR 0x01 /* baud rate divisor low byte register */ 375 #define IT8708_C0BDHR 0x02 /* baud rate divisor high byte register */ 376 #define IT8708_C0CFR 0x04 /* carrier frequency register */ 377 378 /* registers whose bank mapping we don't know, since they weren't being used 379 * in the hacked driver... most probably they belong to the high bank too, 380 * since they fit in the holes the other registers leave */ 381 #define IT8708_C0SCK 0x03 /* slow clock control register */ 382 #define IT8708_C0WCL 0x05 /* wakeup code length register */ 383 #define IT8708_C0WCR 0x06 /* wakeup code read/write register */ 384 #define IT8708_C0WPS 0x07 /* wakeup power control/status register */ 385 386 #define IT8708_IOREG_LENGTH 0x08 /* length of register file */ 387 388 /* two more registers that are defined in the hacked driver, but can't be 389 * found in the data sheets; no idea what they are or how they are accessed, 390 * since the hacked driver doesn't seem to use them */ 391 #define IT8708_CSCRR 0x00 392 #define IT8708_CGPINTR 0x01 393 394 /* CSCRR bits */ 395 #define IT8708_CSCRR_SCRB 0x3f 396 #define IT8708_CSCRR_PM 0x80 397 398 /* CGPINTR bits */ 399 #define IT8708_CGPINT 0x01 400 401 /* 402 * ITE8709 403 * 404 * Hardware interfacing data obtained from the original lirc_ite8709 driver. 405 * Verbatim from its sources: 406 * 407 * The ITE8709 device seems to be the combination of IT8512 superIO chip and 408 * a specific firmware running on the IT8512's embedded micro-controller. 409 * In addition of the embedded micro-controller, the IT8512 chip contains a 410 * CIR module and several other modules. A few modules are directly accessible 411 * by the host CPU, but most of them are only accessible by the 412 * micro-controller. The CIR module is only accessible by the 413 * micro-controller. 414 * 415 * The battery-backed SRAM module is accessible by the host CPU and the 416 * micro-controller. So one of the MC's firmware role is to act as a bridge 417 * between the host CPU and the CIR module. The firmware implements a kind of 418 * communication protocol using the SRAM module as a shared memory. The IT8512 419 * specification is publicly available on ITE's web site, but the 420 * communication protocol is not, so it was reverse-engineered. 421 */ 422 423 /* register offsets */ 424 #define IT8709_RAM_IDX 0x00 /* index into the SRAM module bytes */ 425 #define IT8709_RAM_VAL 0x01 /* read/write data to the indexed byte */ 426 427 #define IT8709_IOREG_LENGTH 0x02 /* length of register file */ 428 429 /* register offsets inside the SRAM module */ 430 #define IT8709_MODE 0x1a /* request/ack byte */ 431 #define IT8709_REG_IDX 0x1b /* index of the CIR register to access */ 432 #define IT8709_REG_VAL 0x1c /* value read/to be written */ 433 #define IT8709_IIR 0x1e /* interrupt identification register */ 434 #define IT8709_RFSR 0x1f /* receiver FIFO status register */ 435 #define IT8709_FIFO 0x20 /* start of in RAM RX FIFO copy */ 436 437 /* MODE values */ 438 #define IT8709_IDLE 0x00 439 #define IT8709_WRITE 0x01 440 #define IT8709_READ 0x02 441