1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * A driver for the CMOS camera controller in the Marvell 88ALP01 "cafe" 4 * multifunction chip. Currently works with the Omnivision OV7670 5 * sensor. 6 * 7 * The data sheet for this device can be found at: 8 * http://wiki.laptop.org/images/5/5c/88ALP01_Datasheet_July_2007.pdf 9 * 10 * Copyright 2006-11 One Laptop Per Child Association, Inc. 11 * Copyright 2006-11 Jonathan Corbet <corbet@lwn.net> 12 * Copyright 2018 Lubomir Rintel <lkundrak@v3.sk> 13 * 14 * Written by Jonathan Corbet, corbet@lwn.net. 15 * 16 * v4l2_device/v4l2_subdev conversion by: 17 * Copyright (C) 2009 Hans Verkuil <hverkuil@xs4all.nl> 18 */ 19 #include <linux/kernel.h> 20 #include <linux/module.h> 21 #include <linux/init.h> 22 #include <linux/pci.h> 23 #include <linux/i2c.h> 24 #include <linux/interrupt.h> 25 #include <linux/spinlock.h> 26 #include <linux/slab.h> 27 #include <linux/videodev2.h> 28 #include <media/v4l2-device.h> 29 #include <media/i2c/ov7670.h> 30 #include <linux/device.h> 31 #include <linux/wait.h> 32 #include <linux/delay.h> 33 #include <linux/io.h> 34 #include <linux/clkdev.h> 35 36 #include "mcam-core.h" 37 38 #define CAFE_VERSION 0x000002 39 40 41 /* 42 * Parameters. 43 */ 44 MODULE_AUTHOR("Jonathan Corbet <corbet@lwn.net>"); 45 MODULE_DESCRIPTION("Marvell 88ALP01 CMOS Camera Controller driver"); 46 MODULE_LICENSE("GPL"); 47 48 struct cafe_camera { 49 int registered; /* Fully initialized? */ 50 struct mcam_camera mcam; 51 struct pci_dev *pdev; 52 struct i2c_adapter *i2c_adapter; 53 wait_queue_head_t smbus_wait; /* Waiting on i2c events */ 54 }; 55 56 /* 57 * Most of the camera controller registers are defined in mcam-core.h, 58 * but the Cafe platform has some additional registers of its own; 59 * they are described here. 60 */ 61 62 /* 63 * "General purpose register" has a couple of GPIOs used for sensor 64 * power and reset on OLPC XO 1.0 systems. 65 */ 66 #define REG_GPR 0xb4 67 #define GPR_C1EN 0x00000020 /* Pad 1 (power down) enable */ 68 #define GPR_C0EN 0x00000010 /* Pad 0 (reset) enable */ 69 #define GPR_C1 0x00000002 /* Control 1 value */ 70 /* 71 * Control 0 is wired to reset on OLPC machines. For ov7x sensors, 72 * it is active low. 73 */ 74 #define GPR_C0 0x00000001 /* Control 0 value */ 75 76 /* 77 * These registers control the SMBUS module for communicating 78 * with the sensor. 79 */ 80 #define REG_TWSIC0 0xb8 /* TWSI (smbus) control 0 */ 81 #define TWSIC0_EN 0x00000001 /* TWSI enable */ 82 #define TWSIC0_MODE 0x00000002 /* 1 = 16-bit, 0 = 8-bit */ 83 #define TWSIC0_SID 0x000003fc /* Slave ID */ 84 /* 85 * Subtle trickery: the slave ID field starts with bit 2. But the 86 * Linux i2c stack wants to treat the bottommost bit as a separate 87 * read/write bit, which is why slave ID's are usually presented 88 * >>1. For consistency with that behavior, we shift over three 89 * bits instead of two. 90 */ 91 #define TWSIC0_SID_SHIFT 3 92 #define TWSIC0_CLKDIV 0x0007fc00 /* Clock divider */ 93 #define TWSIC0_MASKACK 0x00400000 /* Mask ack from sensor */ 94 #define TWSIC0_OVMAGIC 0x00800000 /* Make it work on OV sensors */ 95 96 #define REG_TWSIC1 0xbc /* TWSI control 1 */ 97 #define TWSIC1_DATA 0x0000ffff /* Data to/from camchip */ 98 #define TWSIC1_ADDR 0x00ff0000 /* Address (register) */ 99 #define TWSIC1_ADDR_SHIFT 16 100 #define TWSIC1_READ 0x01000000 /* Set for read op */ 101 #define TWSIC1_WSTAT 0x02000000 /* Write status */ 102 #define TWSIC1_RVALID 0x04000000 /* Read data valid */ 103 #define TWSIC1_ERROR 0x08000000 /* Something screwed up */ 104 105 /* 106 * Here's the weird global control registers 107 */ 108 #define REG_GL_CSR 0x3004 /* Control/status register */ 109 #define GCSR_SRS 0x00000001 /* SW Reset set */ 110 #define GCSR_SRC 0x00000002 /* SW Reset clear */ 111 #define GCSR_MRS 0x00000004 /* Master reset set */ 112 #define GCSR_MRC 0x00000008 /* HW Reset clear */ 113 #define GCSR_CCIC_EN 0x00004000 /* CCIC Clock enable */ 114 #define REG_GL_IMASK 0x300c /* Interrupt mask register */ 115 #define GIMSK_CCIC_EN 0x00000004 /* CCIC Interrupt enable */ 116 117 #define REG_GL_FCR 0x3038 /* GPIO functional control register */ 118 #define GFCR_GPIO_ON 0x08 /* Camera GPIO enabled */ 119 #define REG_GL_GPIOR 0x315c /* GPIO register */ 120 #define GGPIO_OUT 0x80000 /* GPIO output */ 121 #define GGPIO_VAL 0x00008 /* Output pin value */ 122 123 #define REG_LEN (REG_GL_IMASK + 4) 124 125 126 /* 127 * Debugging and related. 128 */ 129 #define cam_err(cam, fmt, arg...) \ 130 dev_err(&(cam)->pdev->dev, fmt, ##arg); 131 #define cam_warn(cam, fmt, arg...) \ 132 dev_warn(&(cam)->pdev->dev, fmt, ##arg); 133 134 /* -------------------------------------------------------------------- */ 135 /* 136 * The I2C/SMBUS interface to the camera itself starts here. The 137 * controller handles SMBUS itself, presenting a relatively simple register 138 * interface; all we have to do is to tell it where to route the data. 139 */ 140 #define CAFE_SMBUS_TIMEOUT (HZ) /* generous */ 141 142 static int cafe_smbus_write_done(struct mcam_camera *mcam) 143 { 144 unsigned long flags; 145 int c1; 146 147 /* 148 * We must delay after the interrupt, or the controller gets confused 149 * and never does give us good status. Fortunately, we don't do this 150 * often. 151 */ 152 udelay(20); 153 spin_lock_irqsave(&mcam->dev_lock, flags); 154 c1 = mcam_reg_read(mcam, REG_TWSIC1); 155 spin_unlock_irqrestore(&mcam->dev_lock, flags); 156 return (c1 & (TWSIC1_WSTAT|TWSIC1_ERROR)) != TWSIC1_WSTAT; 157 } 158 159 static int cafe_smbus_write_data(struct cafe_camera *cam, 160 u16 addr, u8 command, u8 value) 161 { 162 unsigned int rval; 163 unsigned long flags; 164 struct mcam_camera *mcam = &cam->mcam; 165 166 spin_lock_irqsave(&mcam->dev_lock, flags); 167 rval = TWSIC0_EN | ((addr << TWSIC0_SID_SHIFT) & TWSIC0_SID); 168 rval |= TWSIC0_OVMAGIC; /* Make OV sensors work */ 169 /* 170 * Marvell sez set clkdiv to all 1's for now. 171 */ 172 rval |= TWSIC0_CLKDIV; 173 mcam_reg_write(mcam, REG_TWSIC0, rval); 174 (void) mcam_reg_read(mcam, REG_TWSIC1); /* force write */ 175 rval = value | ((command << TWSIC1_ADDR_SHIFT) & TWSIC1_ADDR); 176 mcam_reg_write(mcam, REG_TWSIC1, rval); 177 spin_unlock_irqrestore(&mcam->dev_lock, flags); 178 179 /* Unfortunately, reading TWSIC1 too soon after sending a command 180 * causes the device to die. 181 * Use a busy-wait because we often send a large quantity of small 182 * commands at-once; using msleep() would cause a lot of context 183 * switches which take longer than 2ms, resulting in a noticeable 184 * boot-time and capture-start delays. 185 */ 186 mdelay(2); 187 188 /* 189 * Another sad fact is that sometimes, commands silently complete but 190 * cafe_smbus_write_done() never becomes aware of this. 191 * This happens at random and appears to possible occur with any 192 * command. 193 * We don't understand why this is. We work around this issue 194 * with the timeout in the wait below, assuming that all commands 195 * complete within the timeout. 196 */ 197 wait_event_timeout(cam->smbus_wait, cafe_smbus_write_done(mcam), 198 CAFE_SMBUS_TIMEOUT); 199 200 spin_lock_irqsave(&mcam->dev_lock, flags); 201 rval = mcam_reg_read(mcam, REG_TWSIC1); 202 spin_unlock_irqrestore(&mcam->dev_lock, flags); 203 204 if (rval & TWSIC1_WSTAT) { 205 cam_err(cam, "SMBUS write (%02x/%02x/%02x) timed out\n", addr, 206 command, value); 207 return -EIO; 208 } 209 if (rval & TWSIC1_ERROR) { 210 cam_err(cam, "SMBUS write (%02x/%02x/%02x) error\n", addr, 211 command, value); 212 return -EIO; 213 } 214 return 0; 215 } 216 217 218 219 static int cafe_smbus_read_done(struct mcam_camera *mcam) 220 { 221 unsigned long flags; 222 int c1; 223 224 /* 225 * We must delay after the interrupt, or the controller gets confused 226 * and never does give us good status. Fortunately, we don't do this 227 * often. 228 */ 229 udelay(20); 230 spin_lock_irqsave(&mcam->dev_lock, flags); 231 c1 = mcam_reg_read(mcam, REG_TWSIC1); 232 spin_unlock_irqrestore(&mcam->dev_lock, flags); 233 return c1 & (TWSIC1_RVALID|TWSIC1_ERROR); 234 } 235 236 237 238 static int cafe_smbus_read_data(struct cafe_camera *cam, 239 u16 addr, u8 command, u8 *value) 240 { 241 unsigned int rval; 242 unsigned long flags; 243 struct mcam_camera *mcam = &cam->mcam; 244 245 spin_lock_irqsave(&mcam->dev_lock, flags); 246 rval = TWSIC0_EN | ((addr << TWSIC0_SID_SHIFT) & TWSIC0_SID); 247 rval |= TWSIC0_OVMAGIC; /* Make OV sensors work */ 248 /* 249 * Marvel sez set clkdiv to all 1's for now. 250 */ 251 rval |= TWSIC0_CLKDIV; 252 mcam_reg_write(mcam, REG_TWSIC0, rval); 253 (void) mcam_reg_read(mcam, REG_TWSIC1); /* force write */ 254 rval = TWSIC1_READ | ((command << TWSIC1_ADDR_SHIFT) & TWSIC1_ADDR); 255 mcam_reg_write(mcam, REG_TWSIC1, rval); 256 spin_unlock_irqrestore(&mcam->dev_lock, flags); 257 258 wait_event_timeout(cam->smbus_wait, 259 cafe_smbus_read_done(mcam), CAFE_SMBUS_TIMEOUT); 260 spin_lock_irqsave(&mcam->dev_lock, flags); 261 rval = mcam_reg_read(mcam, REG_TWSIC1); 262 spin_unlock_irqrestore(&mcam->dev_lock, flags); 263 264 if (rval & TWSIC1_ERROR) { 265 cam_err(cam, "SMBUS read (%02x/%02x) error\n", addr, command); 266 return -EIO; 267 } 268 if (!(rval & TWSIC1_RVALID)) { 269 cam_err(cam, "SMBUS read (%02x/%02x) timed out\n", addr, 270 command); 271 return -EIO; 272 } 273 *value = rval & 0xff; 274 return 0; 275 } 276 277 /* 278 * Perform a transfer over SMBUS. This thing is called under 279 * the i2c bus lock, so we shouldn't race with ourselves... 280 */ 281 static int cafe_smbus_xfer(struct i2c_adapter *adapter, u16 addr, 282 unsigned short flags, char rw, u8 command, 283 int size, union i2c_smbus_data *data) 284 { 285 struct cafe_camera *cam = i2c_get_adapdata(adapter); 286 int ret = -EINVAL; 287 288 /* 289 * This interface would appear to only do byte data ops. OK 290 * it can do word too, but the cam chip has no use for that. 291 */ 292 if (size != I2C_SMBUS_BYTE_DATA) { 293 cam_err(cam, "funky xfer size %d\n", size); 294 return -EINVAL; 295 } 296 297 if (rw == I2C_SMBUS_WRITE) 298 ret = cafe_smbus_write_data(cam, addr, command, data->byte); 299 else if (rw == I2C_SMBUS_READ) 300 ret = cafe_smbus_read_data(cam, addr, command, &data->byte); 301 return ret; 302 } 303 304 305 static void cafe_smbus_enable_irq(struct cafe_camera *cam) 306 { 307 unsigned long flags; 308 309 spin_lock_irqsave(&cam->mcam.dev_lock, flags); 310 mcam_reg_set_bit(&cam->mcam, REG_IRQMASK, TWSIIRQS); 311 spin_unlock_irqrestore(&cam->mcam.dev_lock, flags); 312 } 313 314 static u32 cafe_smbus_func(struct i2c_adapter *adapter) 315 { 316 return I2C_FUNC_SMBUS_READ_BYTE_DATA | 317 I2C_FUNC_SMBUS_WRITE_BYTE_DATA; 318 } 319 320 static const struct i2c_algorithm cafe_smbus_algo = { 321 .smbus_xfer = cafe_smbus_xfer, 322 .functionality = cafe_smbus_func 323 }; 324 325 static int cafe_smbus_setup(struct cafe_camera *cam) 326 { 327 struct i2c_adapter *adap; 328 int ret; 329 330 adap = kzalloc(sizeof(*adap), GFP_KERNEL); 331 if (adap == NULL) 332 return -ENOMEM; 333 adap->owner = THIS_MODULE; 334 adap->algo = &cafe_smbus_algo; 335 strscpy(adap->name, "cafe_ccic", sizeof(adap->name)); 336 adap->dev.parent = &cam->pdev->dev; 337 i2c_set_adapdata(adap, cam); 338 ret = i2c_add_adapter(adap); 339 if (ret) { 340 printk(KERN_ERR "Unable to register cafe i2c adapter\n"); 341 kfree(adap); 342 return ret; 343 } 344 345 cam->i2c_adapter = adap; 346 cafe_smbus_enable_irq(cam); 347 return 0; 348 } 349 350 static void cafe_smbus_shutdown(struct cafe_camera *cam) 351 { 352 i2c_del_adapter(cam->i2c_adapter); 353 kfree(cam->i2c_adapter); 354 } 355 356 357 /* 358 * Controller-level stuff 359 */ 360 361 static void cafe_ctlr_init(struct mcam_camera *mcam) 362 { 363 unsigned long flags; 364 365 spin_lock_irqsave(&mcam->dev_lock, flags); 366 /* 367 * Added magic to bring up the hardware on the B-Test board 368 */ 369 mcam_reg_write(mcam, 0x3038, 0x8); 370 mcam_reg_write(mcam, 0x315c, 0x80008); 371 /* 372 * Go through the dance needed to wake the device up. 373 * Note that these registers are global and shared 374 * with the NAND and SD devices. Interaction between the 375 * three still needs to be examined. 376 */ 377 mcam_reg_write(mcam, REG_GL_CSR, GCSR_SRS|GCSR_MRS); /* Needed? */ 378 mcam_reg_write(mcam, REG_GL_CSR, GCSR_SRC|GCSR_MRC); 379 mcam_reg_write(mcam, REG_GL_CSR, GCSR_SRC|GCSR_MRS); 380 /* 381 * Here we must wait a bit for the controller to come around. 382 */ 383 spin_unlock_irqrestore(&mcam->dev_lock, flags); 384 msleep(5); 385 spin_lock_irqsave(&mcam->dev_lock, flags); 386 387 mcam_reg_write(mcam, REG_GL_CSR, GCSR_CCIC_EN|GCSR_SRC|GCSR_MRC); 388 mcam_reg_set_bit(mcam, REG_GL_IMASK, GIMSK_CCIC_EN); 389 /* 390 * Mask all interrupts. 391 */ 392 mcam_reg_write(mcam, REG_IRQMASK, 0); 393 spin_unlock_irqrestore(&mcam->dev_lock, flags); 394 } 395 396 397 static int cafe_ctlr_power_up(struct mcam_camera *mcam) 398 { 399 /* 400 * Part one of the sensor dance: turn the global 401 * GPIO signal on. 402 */ 403 mcam_reg_write(mcam, REG_GL_FCR, GFCR_GPIO_ON); 404 mcam_reg_write(mcam, REG_GL_GPIOR, GGPIO_OUT|GGPIO_VAL); 405 /* 406 * Put the sensor into operational mode (assumes OLPC-style 407 * wiring). Control 0 is reset - set to 1 to operate. 408 * Control 1 is power down, set to 0 to operate. 409 */ 410 mcam_reg_write(mcam, REG_GPR, GPR_C1EN|GPR_C0EN); /* pwr up, reset */ 411 mcam_reg_write(mcam, REG_GPR, GPR_C1EN|GPR_C0EN|GPR_C0); 412 413 return 0; 414 } 415 416 static void cafe_ctlr_power_down(struct mcam_camera *mcam) 417 { 418 mcam_reg_write(mcam, REG_GPR, GPR_C1EN|GPR_C0EN|GPR_C1); 419 mcam_reg_write(mcam, REG_GL_FCR, GFCR_GPIO_ON); 420 mcam_reg_write(mcam, REG_GL_GPIOR, GGPIO_OUT); 421 } 422 423 424 425 /* 426 * The platform interrupt handler. 427 */ 428 static irqreturn_t cafe_irq(int irq, void *data) 429 { 430 struct cafe_camera *cam = data; 431 struct mcam_camera *mcam = &cam->mcam; 432 unsigned int irqs, handled; 433 434 spin_lock(&mcam->dev_lock); 435 irqs = mcam_reg_read(mcam, REG_IRQSTAT); 436 handled = cam->registered && mccic_irq(mcam, irqs); 437 if (irqs & TWSIIRQS) { 438 mcam_reg_write(mcam, REG_IRQSTAT, TWSIIRQS); 439 wake_up(&cam->smbus_wait); 440 handled = 1; 441 } 442 spin_unlock(&mcam->dev_lock); 443 return IRQ_RETVAL(handled); 444 } 445 446 /* -------------------------------------------------------------------------- */ 447 448 static struct ov7670_config sensor_cfg = { 449 /* 450 * Exclude QCIF mode, because it only captures a tiny portion 451 * of the sensor FOV 452 */ 453 .min_width = 320, 454 .min_height = 240, 455 456 /* 457 * Set the clock speed for the XO 1; I don't believe this 458 * driver has ever run anywhere else. 459 */ 460 .clock_speed = 45, 461 .use_smbus = 1, 462 }; 463 464 static struct i2c_board_info ov7670_info = { 465 .type = "ov7670", 466 .addr = 0x42 >> 1, 467 .platform_data = &sensor_cfg, 468 }; 469 470 /* -------------------------------------------------------------------------- */ 471 /* 472 * PCI interface stuff. 473 */ 474 475 static int cafe_pci_probe(struct pci_dev *pdev, 476 const struct pci_device_id *id) 477 { 478 int ret; 479 struct cafe_camera *cam; 480 struct mcam_camera *mcam; 481 struct v4l2_async_connection *asd; 482 struct i2c_client *i2c_dev; 483 484 /* 485 * Start putting together one of our big camera structures. 486 */ 487 ret = -ENOMEM; 488 cam = kzalloc(sizeof(struct cafe_camera), GFP_KERNEL); 489 if (cam == NULL) 490 goto out; 491 pci_set_drvdata(pdev, cam); 492 cam->pdev = pdev; 493 mcam = &cam->mcam; 494 mcam->chip_id = MCAM_CAFE; 495 spin_lock_init(&mcam->dev_lock); 496 init_waitqueue_head(&cam->smbus_wait); 497 mcam->plat_power_up = cafe_ctlr_power_up; 498 mcam->plat_power_down = cafe_ctlr_power_down; 499 mcam->dev = &pdev->dev; 500 /* 501 * Vmalloc mode for buffers is traditional with this driver. 502 * We *might* be able to run DMA_contig, especially on a system 503 * with CMA in it. 504 */ 505 mcam->buffer_mode = B_vmalloc; 506 /* 507 * Get set up on the PCI bus. 508 */ 509 ret = pci_enable_device(pdev); 510 if (ret) 511 goto out_free; 512 pci_set_master(pdev); 513 514 ret = -EIO; 515 mcam->regs = pci_iomap(pdev, 0, 0); 516 if (!mcam->regs) { 517 printk(KERN_ERR "Unable to ioremap cafe-ccic regs\n"); 518 goto out_disable; 519 } 520 mcam->regs_size = pci_resource_len(pdev, 0); 521 ret = request_irq(pdev->irq, cafe_irq, IRQF_SHARED, "cafe-ccic", cam); 522 if (ret) 523 goto out_iounmap; 524 525 /* 526 * Initialize the controller. 527 */ 528 cafe_ctlr_init(mcam); 529 530 /* 531 * Set up I2C/SMBUS communications. We have to drop the mutex here 532 * because the sensor could attach in this call chain, leading to 533 * unsightly deadlocks. 534 */ 535 ret = cafe_smbus_setup(cam); 536 if (ret) 537 goto out_pdown; 538 539 ret = v4l2_device_register(mcam->dev, &mcam->v4l2_dev); 540 if (ret) 541 goto out_smbus_shutdown; 542 543 v4l2_async_nf_init(&mcam->notifier, &mcam->v4l2_dev); 544 545 asd = v4l2_async_nf_add_i2c(&mcam->notifier, 546 i2c_adapter_id(cam->i2c_adapter), 547 ov7670_info.addr, 548 struct v4l2_async_connection); 549 if (IS_ERR(asd)) { 550 ret = PTR_ERR(asd); 551 goto out_v4l2_device_unregister; 552 } 553 554 ret = mccic_register(mcam); 555 if (ret) 556 goto out_v4l2_device_unregister; 557 558 clkdev_create(mcam->mclk, "xclk", "%d-%04x", 559 i2c_adapter_id(cam->i2c_adapter), ov7670_info.addr); 560 561 i2c_dev = i2c_new_client_device(cam->i2c_adapter, &ov7670_info); 562 if (IS_ERR(i2c_dev)) { 563 ret = PTR_ERR(i2c_dev); 564 goto out_mccic_shutdown; 565 } 566 567 cam->registered = 1; 568 return 0; 569 570 out_mccic_shutdown: 571 mccic_shutdown(mcam); 572 out_v4l2_device_unregister: 573 v4l2_device_unregister(&mcam->v4l2_dev); 574 out_smbus_shutdown: 575 cafe_smbus_shutdown(cam); 576 out_pdown: 577 cafe_ctlr_power_down(mcam); 578 free_irq(pdev->irq, cam); 579 out_iounmap: 580 pci_iounmap(pdev, mcam->regs); 581 out_disable: 582 pci_disable_device(pdev); 583 out_free: 584 kfree(cam); 585 out: 586 return ret; 587 } 588 589 590 /* 591 * Shut down an initialized device 592 */ 593 static void cafe_shutdown(struct cafe_camera *cam) 594 { 595 mccic_shutdown(&cam->mcam); 596 v4l2_device_unregister(&cam->mcam.v4l2_dev); 597 cafe_smbus_shutdown(cam); 598 free_irq(cam->pdev->irq, cam); 599 pci_iounmap(cam->pdev, cam->mcam.regs); 600 } 601 602 603 static void cafe_pci_remove(struct pci_dev *pdev) 604 { 605 struct cafe_camera *cam = pci_get_drvdata(pdev); 606 607 if (cam == NULL) { 608 printk(KERN_WARNING "pci_remove on unknown pdev %p\n", pdev); 609 return; 610 } 611 cafe_shutdown(cam); 612 kfree(cam); 613 } 614 615 616 /* 617 * Basic power management. 618 */ 619 static int __maybe_unused cafe_pci_suspend(struct device *dev) 620 { 621 struct cafe_camera *cam = dev_get_drvdata(dev); 622 623 mccic_suspend(&cam->mcam); 624 return 0; 625 } 626 627 628 static int __maybe_unused cafe_pci_resume(struct device *dev) 629 { 630 struct cafe_camera *cam = dev_get_drvdata(dev); 631 632 cafe_ctlr_init(&cam->mcam); 633 return mccic_resume(&cam->mcam); 634 } 635 636 static const struct pci_device_id cafe_ids[] = { 637 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 638 PCI_DEVICE_ID_MARVELL_88ALP01_CCIC) }, 639 { 0, } 640 }; 641 642 MODULE_DEVICE_TABLE(pci, cafe_ids); 643 644 static SIMPLE_DEV_PM_OPS(cafe_pci_pm_ops, cafe_pci_suspend, cafe_pci_resume); 645 646 static struct pci_driver cafe_pci_driver = { 647 .name = "cafe1000-ccic", 648 .id_table = cafe_ids, 649 .probe = cafe_pci_probe, 650 .remove = cafe_pci_remove, 651 .driver.pm = &cafe_pci_pm_ops, 652 }; 653 654 655 656 657 static int __init cafe_init(void) 658 { 659 int ret; 660 661 printk(KERN_NOTICE "Marvell M88ALP01 'CAFE' Camera Controller version %d\n", 662 CAFE_VERSION); 663 ret = pci_register_driver(&cafe_pci_driver); 664 if (ret) { 665 printk(KERN_ERR "Unable to register cafe_ccic driver\n"); 666 goto out; 667 } 668 ret = 0; 669 670 out: 671 return ret; 672 } 673 674 675 static void __exit cafe_exit(void) 676 { 677 pci_unregister_driver(&cafe_pci_driver); 678 } 679 680 module_init(cafe_init); 681 module_exit(cafe_exit); 682