1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3  * budget-ci.c: driver for the SAA7146 based Budget DVB cards
4  *
5  * Compiled from various sources by Michael Hunold <michael@mihu.de>
6  *
7  *     msp430 IR support contributed by Jack Thomasson <jkt@Helius.COM>
8  *     partially based on the Siemens DVB driver by Ralph+Marcus Metzler
9  *
10  * CI interface support (c) 2004 Andrew de Quincey <adq_dvb@lidskialf.net>
11  *
12  * the project's page is at https://linuxtv.org
13  */
14 
15 #include <linux/module.h>
16 #include <linux/errno.h>
17 #include <linux/slab.h>
18 #include <linux/interrupt.h>
19 #include <linux/spinlock.h>
20 #include <media/rc-core.h>
21 
22 #include "budget.h"
23 
24 #include <media/dvb_ca_en50221.h>
25 #include "stv0299.h"
26 #include "stv0297.h"
27 #include "tda1004x.h"
28 #include "stb0899_drv.h"
29 #include "stb0899_reg.h"
30 #include "stb0899_cfg.h"
31 #include "stb6100.h"
32 #include "stb6100_cfg.h"
33 #include "lnbp21.h"
34 #include "bsbe1.h"
35 #include "bsru6.h"
36 #include "tda1002x.h"
37 #include "tda827x.h"
38 #include "bsbe1-d01a.h"
39 
40 #define MODULE_NAME "budget_ci"
41 
42 /*
43  * Regarding DEBIADDR_IR:
44  * Some CI modules hang if random addresses are read.
45  * Using address 0x4000 for the IR read means that we
46  * use the same address as for CI version, which should
47  * be a safe default.
48  */
49 #define DEBIADDR_IR		0x4000
50 #define DEBIADDR_CICONTROL	0x0000
51 #define DEBIADDR_CIVERSION	0x4000
52 #define DEBIADDR_IO		0x1000
53 #define DEBIADDR_ATTR		0x3000
54 
55 #define CICONTROL_RESET		0x01
56 #define CICONTROL_ENABLETS	0x02
57 #define CICONTROL_CAMDETECT	0x08
58 
59 #define DEBICICTL		0x00420000
60 #define DEBICICAM		0x02420000
61 
62 #define SLOTSTATUS_NONE		1
63 #define SLOTSTATUS_PRESENT	2
64 #define SLOTSTATUS_RESET	4
65 #define SLOTSTATUS_READY	8
66 #define SLOTSTATUS_OCCUPIED	(SLOTSTATUS_PRESENT|SLOTSTATUS_RESET|SLOTSTATUS_READY)
67 
68 /* RC5 device wildcard */
69 #define IR_DEVICE_ANY		255
70 
71 static int rc5_device = -1;
72 module_param(rc5_device, int, 0644);
73 MODULE_PARM_DESC(rc5_device, "only IR commands to given RC5 device (device = 0 - 31, any device = 255, default: autodetect)");
74 
75 static int ir_debug;
76 module_param(ir_debug, int, 0644);
77 MODULE_PARM_DESC(ir_debug, "enable debugging information for IR decoding");
78 
79 DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr);
80 
81 struct budget_ci_ir {
82 	struct rc_dev *dev;
83 	struct tasklet_struct msp430_irq_tasklet;
84 	char name[72]; /* 40 + 32 for (struct saa7146_dev).name */
85 	char phys[32];
86 	int rc5_device;
87 	u32 ir_key;
88 	bool have_command;
89 	bool full_rc5;		/* Outputs a full RC5 code */
90 };
91 
92 struct budget_ci {
93 	struct budget budget;
94 	struct tasklet_struct ciintf_irq_tasklet;
95 	int slot_status;
96 	int ci_irq;
97 	struct dvb_ca_en50221 ca;
98 	struct budget_ci_ir ir;
99 	u8 tuner_pll_address; /* used for philips_tdm1316l configs */
100 };
101 
102 static void msp430_ir_interrupt(struct tasklet_struct *t)
103 {
104 	struct budget_ci_ir *ir = from_tasklet(ir, t, msp430_irq_tasklet);
105 	struct budget_ci *budget_ci = container_of(ir, typeof(*budget_ci), ir);
106 	struct rc_dev *dev = budget_ci->ir.dev;
107 	u32 command = ttpci_budget_debiread(&budget_ci->budget, DEBINOSWAP, DEBIADDR_IR, 2, 1, 0) >> 8;
108 
109 	/*
110 	 * The msp430 chip can generate two different bytes, command and device
111 	 *
112 	 * type1: X1CCCCCC, C = command bits (0 - 63)
113 	 * type2: X0TDDDDD, D = device bits (0 - 31), T = RC5 toggle bit
114 	 *
115 	 * Each signal from the remote control can generate one or more command
116 	 * bytes and one or more device bytes. For the repeated bytes, the
117 	 * highest bit (X) is set. The first command byte is always generated
118 	 * before the first device byte. Other than that, no specific order
119 	 * seems to apply. To make life interesting, bytes can also be lost.
120 	 *
121 	 * Only when we have a command and device byte, a keypress is
122 	 * generated.
123 	 */
124 
125 	if (ir_debug)
126 		printk("budget_ci: received byte 0x%02x\n", command);
127 
128 	/* Remove repeat bit, we use every command */
129 	command = command & 0x7f;
130 
131 	/* Is this a RC5 command byte? */
132 	if (command & 0x40) {
133 		budget_ci->ir.have_command = true;
134 		budget_ci->ir.ir_key = command & 0x3f;
135 		return;
136 	}
137 
138 	/* It's a RC5 device byte */
139 	if (!budget_ci->ir.have_command)
140 		return;
141 	budget_ci->ir.have_command = false;
142 
143 	if (budget_ci->ir.rc5_device != IR_DEVICE_ANY &&
144 	    budget_ci->ir.rc5_device != (command & 0x1f))
145 		return;
146 
147 	if (budget_ci->ir.full_rc5) {
148 		rc_keydown(dev, RC_PROTO_RC5,
149 			   RC_SCANCODE_RC5(budget_ci->ir.rc5_device, budget_ci->ir.ir_key),
150 			   !!(command & 0x20));
151 		return;
152 	}
153 
154 	/* FIXME: We should generate complete scancodes for all devices */
155 	rc_keydown(dev, RC_PROTO_UNKNOWN, budget_ci->ir.ir_key,
156 		   !!(command & 0x20));
157 }
158 
159 static int msp430_ir_init(struct budget_ci *budget_ci)
160 {
161 	struct saa7146_dev *saa = budget_ci->budget.dev;
162 	struct rc_dev *dev;
163 	int error;
164 
165 	dev = rc_allocate_device(RC_DRIVER_SCANCODE);
166 	if (!dev) {
167 		printk(KERN_ERR "budget_ci: IR interface initialisation failed\n");
168 		return -ENOMEM;
169 	}
170 
171 	snprintf(budget_ci->ir.name, sizeof(budget_ci->ir.name),
172 		 "Budget-CI dvb ir receiver %s", saa->name);
173 	snprintf(budget_ci->ir.phys, sizeof(budget_ci->ir.phys),
174 		 "pci-%s/ir0", pci_name(saa->pci));
175 
176 	dev->driver_name = MODULE_NAME;
177 	dev->device_name = budget_ci->ir.name;
178 	dev->input_phys = budget_ci->ir.phys;
179 	dev->input_id.bustype = BUS_PCI;
180 	dev->input_id.version = 1;
181 	if (saa->pci->subsystem_vendor) {
182 		dev->input_id.vendor = saa->pci->subsystem_vendor;
183 		dev->input_id.product = saa->pci->subsystem_device;
184 	} else {
185 		dev->input_id.vendor = saa->pci->vendor;
186 		dev->input_id.product = saa->pci->device;
187 	}
188 	dev->dev.parent = &saa->pci->dev;
189 
190 	if (rc5_device < 0)
191 		budget_ci->ir.rc5_device = IR_DEVICE_ANY;
192 	else
193 		budget_ci->ir.rc5_device = rc5_device;
194 
195 	/* Select keymap and address */
196 	switch (budget_ci->budget.dev->pci->subsystem_device) {
197 	case 0x100c:
198 	case 0x100f:
199 	case 0x1011:
200 	case 0x1012:
201 		/* The hauppauge keymap is a superset of these remotes */
202 		dev->map_name = RC_MAP_HAUPPAUGE;
203 		budget_ci->ir.full_rc5 = true;
204 
205 		if (rc5_device < 0)
206 			budget_ci->ir.rc5_device = 0x1f;
207 		break;
208 	case 0x1010:
209 	case 0x1017:
210 	case 0x1019:
211 	case 0x101a:
212 	case 0x101b:
213 		/* for the Technotrend 1500 bundled remote */
214 		dev->map_name = RC_MAP_TT_1500;
215 		break;
216 	default:
217 		/* unknown remote */
218 		dev->map_name = RC_MAP_BUDGET_CI_OLD;
219 		break;
220 	}
221 	if (!budget_ci->ir.full_rc5)
222 		dev->scancode_mask = 0xff;
223 
224 	error = rc_register_device(dev);
225 	if (error) {
226 		printk(KERN_ERR "budget_ci: could not init driver for IR device (code %d)\n", error);
227 		rc_free_device(dev);
228 		return error;
229 	}
230 
231 	budget_ci->ir.dev = dev;
232 
233 	tasklet_setup(&budget_ci->ir.msp430_irq_tasklet, msp430_ir_interrupt);
234 
235 	SAA7146_IER_ENABLE(saa, MASK_06);
236 	saa7146_setgpio(saa, 3, SAA7146_GPIO_IRQHI);
237 
238 	return 0;
239 }
240 
241 static void msp430_ir_deinit(struct budget_ci *budget_ci)
242 {
243 	struct saa7146_dev *saa = budget_ci->budget.dev;
244 
245 	SAA7146_IER_DISABLE(saa, MASK_06);
246 	saa7146_setgpio(saa, 3, SAA7146_GPIO_INPUT);
247 	tasklet_kill(&budget_ci->ir.msp430_irq_tasklet);
248 
249 	rc_unregister_device(budget_ci->ir.dev);
250 }
251 
252 static int ciintf_read_attribute_mem(struct dvb_ca_en50221 *ca, int slot, int address)
253 {
254 	struct budget_ci *budget_ci = (struct budget_ci *) ca->data;
255 
256 	if (slot != 0)
257 		return -EINVAL;
258 
259 	return ttpci_budget_debiread(&budget_ci->budget, DEBICICAM,
260 				     DEBIADDR_ATTR | (address & 0xfff), 1, 1, 0);
261 }
262 
263 static int ciintf_write_attribute_mem(struct dvb_ca_en50221 *ca, int slot, int address, u8 value)
264 {
265 	struct budget_ci *budget_ci = (struct budget_ci *) ca->data;
266 
267 	if (slot != 0)
268 		return -EINVAL;
269 
270 	return ttpci_budget_debiwrite(&budget_ci->budget, DEBICICAM,
271 				      DEBIADDR_ATTR | (address & 0xfff), 1, value, 1, 0);
272 }
273 
274 static int ciintf_read_cam_control(struct dvb_ca_en50221 *ca, int slot, u8 address)
275 {
276 	struct budget_ci *budget_ci = (struct budget_ci *) ca->data;
277 
278 	if (slot != 0)
279 		return -EINVAL;
280 
281 	return ttpci_budget_debiread(&budget_ci->budget, DEBICICAM,
282 				     DEBIADDR_IO | (address & 3), 1, 1, 0);
283 }
284 
285 static int ciintf_write_cam_control(struct dvb_ca_en50221 *ca, int slot, u8 address, u8 value)
286 {
287 	struct budget_ci *budget_ci = (struct budget_ci *) ca->data;
288 
289 	if (slot != 0)
290 		return -EINVAL;
291 
292 	return ttpci_budget_debiwrite(&budget_ci->budget, DEBICICAM,
293 				      DEBIADDR_IO | (address & 3), 1, value, 1, 0);
294 }
295 
296 static int ciintf_slot_reset(struct dvb_ca_en50221 *ca, int slot)
297 {
298 	struct budget_ci *budget_ci = (struct budget_ci *) ca->data;
299 	struct saa7146_dev *saa = budget_ci->budget.dev;
300 
301 	if (slot != 0)
302 		return -EINVAL;
303 
304 	if (budget_ci->ci_irq) {
305 		// trigger on RISING edge during reset so we know when READY is re-asserted
306 		saa7146_setgpio(saa, 0, SAA7146_GPIO_IRQHI);
307 	}
308 	budget_ci->slot_status = SLOTSTATUS_RESET;
309 	ttpci_budget_debiwrite(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, 0, 1, 0);
310 	msleep(1);
311 	ttpci_budget_debiwrite(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1,
312 			       CICONTROL_RESET, 1, 0);
313 
314 	saa7146_setgpio(saa, 1, SAA7146_GPIO_OUTHI);
315 	ttpci_budget_set_video_port(saa, BUDGET_VIDEO_PORTB);
316 	return 0;
317 }
318 
319 static int ciintf_slot_shutdown(struct dvb_ca_en50221 *ca, int slot)
320 {
321 	struct budget_ci *budget_ci = (struct budget_ci *) ca->data;
322 	struct saa7146_dev *saa = budget_ci->budget.dev;
323 
324 	if (slot != 0)
325 		return -EINVAL;
326 
327 	saa7146_setgpio(saa, 1, SAA7146_GPIO_OUTHI);
328 	ttpci_budget_set_video_port(saa, BUDGET_VIDEO_PORTB);
329 	return 0;
330 }
331 
332 static int ciintf_slot_ts_enable(struct dvb_ca_en50221 *ca, int slot)
333 {
334 	struct budget_ci *budget_ci = (struct budget_ci *) ca->data;
335 	struct saa7146_dev *saa = budget_ci->budget.dev;
336 	int tmp;
337 
338 	if (slot != 0)
339 		return -EINVAL;
340 
341 	saa7146_setgpio(saa, 1, SAA7146_GPIO_OUTLO);
342 
343 	tmp = ttpci_budget_debiread(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, 1, 0);
344 	ttpci_budget_debiwrite(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1,
345 			       tmp | CICONTROL_ENABLETS, 1, 0);
346 
347 	ttpci_budget_set_video_port(saa, BUDGET_VIDEO_PORTA);
348 	return 0;
349 }
350 
351 static void ciintf_interrupt(struct tasklet_struct *t)
352 {
353 	struct budget_ci *budget_ci = from_tasklet(budget_ci, t,
354 						   ciintf_irq_tasklet);
355 	struct saa7146_dev *saa = budget_ci->budget.dev;
356 	unsigned int flags;
357 
358 	// ensure we don't get spurious IRQs during initialisation
359 	if (!budget_ci->budget.ci_present)
360 		return;
361 
362 	// read the CAM status
363 	flags = ttpci_budget_debiread(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, 1, 0);
364 	if (flags & CICONTROL_CAMDETECT) {
365 
366 		// GPIO should be set to trigger on falling edge if a CAM is present
367 		saa7146_setgpio(saa, 0, SAA7146_GPIO_IRQLO);
368 
369 		if (budget_ci->slot_status & SLOTSTATUS_NONE) {
370 			// CAM insertion IRQ
371 			budget_ci->slot_status = SLOTSTATUS_PRESENT;
372 			dvb_ca_en50221_camchange_irq(&budget_ci->ca, 0,
373 						     DVB_CA_EN50221_CAMCHANGE_INSERTED);
374 
375 		} else if (budget_ci->slot_status & SLOTSTATUS_RESET) {
376 			// CAM ready (reset completed)
377 			budget_ci->slot_status = SLOTSTATUS_READY;
378 			dvb_ca_en50221_camready_irq(&budget_ci->ca, 0);
379 
380 		} else if (budget_ci->slot_status & SLOTSTATUS_READY) {
381 			// FR/DA IRQ
382 			dvb_ca_en50221_frda_irq(&budget_ci->ca, 0);
383 		}
384 	} else {
385 
386 		// trigger on rising edge if a CAM is not present - when a CAM is inserted, we
387 		// only want to get the IRQ when it sets READY. If we trigger on the falling edge,
388 		// the CAM might not actually be ready yet.
389 		saa7146_setgpio(saa, 0, SAA7146_GPIO_IRQHI);
390 
391 		// generate a CAM removal IRQ if we haven't already
392 		if (budget_ci->slot_status & SLOTSTATUS_OCCUPIED) {
393 			// CAM removal IRQ
394 			budget_ci->slot_status = SLOTSTATUS_NONE;
395 			dvb_ca_en50221_camchange_irq(&budget_ci->ca, 0,
396 						     DVB_CA_EN50221_CAMCHANGE_REMOVED);
397 		}
398 	}
399 }
400 
401 static int ciintf_poll_slot_status(struct dvb_ca_en50221 *ca, int slot, int open)
402 {
403 	struct budget_ci *budget_ci = (struct budget_ci *) ca->data;
404 	unsigned int flags;
405 
406 	// ensure we don't get spurious IRQs during initialisation
407 	if (!budget_ci->budget.ci_present)
408 		return -EINVAL;
409 
410 	// read the CAM status
411 	flags = ttpci_budget_debiread(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, 1, 0);
412 	if (flags & CICONTROL_CAMDETECT) {
413 		// mark it as present if it wasn't before
414 		if (budget_ci->slot_status & SLOTSTATUS_NONE) {
415 			budget_ci->slot_status = SLOTSTATUS_PRESENT;
416 		}
417 
418 		// during a RESET, we check if we can read from IO memory to see when CAM is ready
419 		if (budget_ci->slot_status & SLOTSTATUS_RESET) {
420 			if (ciintf_read_attribute_mem(ca, slot, 0) == 0x1d) {
421 				budget_ci->slot_status = SLOTSTATUS_READY;
422 			}
423 		}
424 	} else {
425 		budget_ci->slot_status = SLOTSTATUS_NONE;
426 	}
427 
428 	if (budget_ci->slot_status != SLOTSTATUS_NONE) {
429 		if (budget_ci->slot_status & SLOTSTATUS_READY) {
430 			return DVB_CA_EN50221_POLL_CAM_PRESENT | DVB_CA_EN50221_POLL_CAM_READY;
431 		}
432 		return DVB_CA_EN50221_POLL_CAM_PRESENT;
433 	}
434 
435 	return 0;
436 }
437 
438 static int ciintf_init(struct budget_ci *budget_ci)
439 {
440 	struct saa7146_dev *saa = budget_ci->budget.dev;
441 	int flags;
442 	int result;
443 	int ci_version;
444 	int ca_flags;
445 
446 	memset(&budget_ci->ca, 0, sizeof(struct dvb_ca_en50221));
447 
448 	// enable DEBI pins
449 	saa7146_write(saa, MC1, MASK_27 | MASK_11);
450 
451 	// test if it is there
452 	ci_version = ttpci_budget_debiread(&budget_ci->budget, DEBICICTL, DEBIADDR_CIVERSION, 1, 1, 0);
453 	if ((ci_version & 0xa0) != 0xa0) {
454 		result = -ENODEV;
455 		goto error;
456 	}
457 
458 	// determine whether a CAM is present or not
459 	flags = ttpci_budget_debiread(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, 1, 0);
460 	budget_ci->slot_status = SLOTSTATUS_NONE;
461 	if (flags & CICONTROL_CAMDETECT)
462 		budget_ci->slot_status = SLOTSTATUS_PRESENT;
463 
464 	// version 0xa2 of the CI firmware doesn't generate interrupts
465 	if (ci_version == 0xa2) {
466 		ca_flags = 0;
467 		budget_ci->ci_irq = 0;
468 	} else {
469 		ca_flags = DVB_CA_EN50221_FLAG_IRQ_CAMCHANGE |
470 				DVB_CA_EN50221_FLAG_IRQ_FR |
471 				DVB_CA_EN50221_FLAG_IRQ_DA;
472 		budget_ci->ci_irq = 1;
473 	}
474 
475 	// register CI interface
476 	budget_ci->ca.owner = THIS_MODULE;
477 	budget_ci->ca.read_attribute_mem = ciintf_read_attribute_mem;
478 	budget_ci->ca.write_attribute_mem = ciintf_write_attribute_mem;
479 	budget_ci->ca.read_cam_control = ciintf_read_cam_control;
480 	budget_ci->ca.write_cam_control = ciintf_write_cam_control;
481 	budget_ci->ca.slot_reset = ciintf_slot_reset;
482 	budget_ci->ca.slot_shutdown = ciintf_slot_shutdown;
483 	budget_ci->ca.slot_ts_enable = ciintf_slot_ts_enable;
484 	budget_ci->ca.poll_slot_status = ciintf_poll_slot_status;
485 	budget_ci->ca.data = budget_ci;
486 	if ((result = dvb_ca_en50221_init(&budget_ci->budget.dvb_adapter,
487 					  &budget_ci->ca,
488 					  ca_flags, 1)) != 0) {
489 		printk("budget_ci: CI interface detected, but initialisation failed.\n");
490 		goto error;
491 	}
492 
493 	// Setup CI slot IRQ
494 	if (budget_ci->ci_irq) {
495 		tasklet_setup(&budget_ci->ciintf_irq_tasklet, ciintf_interrupt);
496 		if (budget_ci->slot_status != SLOTSTATUS_NONE) {
497 			saa7146_setgpio(saa, 0, SAA7146_GPIO_IRQLO);
498 		} else {
499 			saa7146_setgpio(saa, 0, SAA7146_GPIO_IRQHI);
500 		}
501 		SAA7146_IER_ENABLE(saa, MASK_03);
502 	}
503 
504 	// enable interface
505 	ttpci_budget_debiwrite(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1,
506 			       CICONTROL_RESET, 1, 0);
507 
508 	// success!
509 	printk("budget_ci: CI interface initialised\n");
510 	budget_ci->budget.ci_present = 1;
511 
512 	// forge a fake CI IRQ so the CAM state is setup correctly
513 	if (budget_ci->ci_irq) {
514 		flags = DVB_CA_EN50221_CAMCHANGE_REMOVED;
515 		if (budget_ci->slot_status != SLOTSTATUS_NONE)
516 			flags = DVB_CA_EN50221_CAMCHANGE_INSERTED;
517 		dvb_ca_en50221_camchange_irq(&budget_ci->ca, 0, flags);
518 	}
519 
520 	return 0;
521 
522 error:
523 	saa7146_write(saa, MC1, MASK_27);
524 	return result;
525 }
526 
527 static void ciintf_deinit(struct budget_ci *budget_ci)
528 {
529 	struct saa7146_dev *saa = budget_ci->budget.dev;
530 
531 	// disable CI interrupts
532 	if (budget_ci->ci_irq) {
533 		SAA7146_IER_DISABLE(saa, MASK_03);
534 		saa7146_setgpio(saa, 0, SAA7146_GPIO_INPUT);
535 		tasklet_kill(&budget_ci->ciintf_irq_tasklet);
536 	}
537 
538 	// reset interface
539 	ttpci_budget_debiwrite(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, 0, 1, 0);
540 	msleep(1);
541 	ttpci_budget_debiwrite(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1,
542 			       CICONTROL_RESET, 1, 0);
543 
544 	// disable TS data stream to CI interface
545 	saa7146_setgpio(saa, 1, SAA7146_GPIO_INPUT);
546 
547 	// release the CA device
548 	dvb_ca_en50221_release(&budget_ci->ca);
549 
550 	// disable DEBI pins
551 	saa7146_write(saa, MC1, MASK_27);
552 }
553 
554 static void budget_ci_irq(struct saa7146_dev *dev, u32 * isr)
555 {
556 	struct budget_ci *budget_ci = (struct budget_ci *) dev->ext_priv;
557 
558 	dprintk(8, "dev: %p, budget_ci: %p\n", dev, budget_ci);
559 
560 	if (*isr & MASK_06)
561 		tasklet_schedule(&budget_ci->ir.msp430_irq_tasklet);
562 
563 	if (*isr & MASK_10)
564 		ttpci_budget_irq10_handler(dev, isr);
565 
566 	if ((*isr & MASK_03) && (budget_ci->budget.ci_present) && (budget_ci->ci_irq))
567 		tasklet_schedule(&budget_ci->ciintf_irq_tasklet);
568 }
569 
570 static u8 philips_su1278_tt_inittab[] = {
571 	0x01, 0x0f,
572 	0x02, 0x30,
573 	0x03, 0x00,
574 	0x04, 0x5b,
575 	0x05, 0x85,
576 	0x06, 0x02,
577 	0x07, 0x00,
578 	0x08, 0x02,
579 	0x09, 0x00,
580 	0x0C, 0x01,
581 	0x0D, 0x81,
582 	0x0E, 0x44,
583 	0x0f, 0x14,
584 	0x10, 0x3c,
585 	0x11, 0x84,
586 	0x12, 0xda,
587 	0x13, 0x97,
588 	0x14, 0x95,
589 	0x15, 0xc9,
590 	0x16, 0x19,
591 	0x17, 0x8c,
592 	0x18, 0x59,
593 	0x19, 0xf8,
594 	0x1a, 0xfe,
595 	0x1c, 0x7f,
596 	0x1d, 0x00,
597 	0x1e, 0x00,
598 	0x1f, 0x50,
599 	0x20, 0x00,
600 	0x21, 0x00,
601 	0x22, 0x00,
602 	0x23, 0x00,
603 	0x28, 0x00,
604 	0x29, 0x28,
605 	0x2a, 0x14,
606 	0x2b, 0x0f,
607 	0x2c, 0x09,
608 	0x2d, 0x09,
609 	0x31, 0x1f,
610 	0x32, 0x19,
611 	0x33, 0xfc,
612 	0x34, 0x93,
613 	0xff, 0xff
614 };
615 
616 static int philips_su1278_tt_set_symbol_rate(struct dvb_frontend *fe, u32 srate, u32 ratio)
617 {
618 	stv0299_writereg(fe, 0x0e, 0x44);
619 	if (srate >= 10000000) {
620 		stv0299_writereg(fe, 0x13, 0x97);
621 		stv0299_writereg(fe, 0x14, 0x95);
622 		stv0299_writereg(fe, 0x15, 0xc9);
623 		stv0299_writereg(fe, 0x17, 0x8c);
624 		stv0299_writereg(fe, 0x1a, 0xfe);
625 		stv0299_writereg(fe, 0x1c, 0x7f);
626 		stv0299_writereg(fe, 0x2d, 0x09);
627 	} else {
628 		stv0299_writereg(fe, 0x13, 0x99);
629 		stv0299_writereg(fe, 0x14, 0x8d);
630 		stv0299_writereg(fe, 0x15, 0xce);
631 		stv0299_writereg(fe, 0x17, 0x43);
632 		stv0299_writereg(fe, 0x1a, 0x1d);
633 		stv0299_writereg(fe, 0x1c, 0x12);
634 		stv0299_writereg(fe, 0x2d, 0x05);
635 	}
636 	stv0299_writereg(fe, 0x0e, 0x23);
637 	stv0299_writereg(fe, 0x0f, 0x94);
638 	stv0299_writereg(fe, 0x10, 0x39);
639 	stv0299_writereg(fe, 0x15, 0xc9);
640 
641 	stv0299_writereg(fe, 0x1f, (ratio >> 16) & 0xff);
642 	stv0299_writereg(fe, 0x20, (ratio >> 8) & 0xff);
643 	stv0299_writereg(fe, 0x21, (ratio) & 0xf0);
644 
645 	return 0;
646 }
647 
648 static int philips_su1278_tt_tuner_set_params(struct dvb_frontend *fe)
649 {
650 	struct dtv_frontend_properties *p = &fe->dtv_property_cache;
651 	struct budget_ci *budget_ci = (struct budget_ci *) fe->dvb->priv;
652 	u32 div;
653 	u8 buf[4];
654 	struct i2c_msg msg = {.addr = 0x60,.flags = 0,.buf = buf,.len = sizeof(buf) };
655 
656 	if ((p->frequency < 950000) || (p->frequency > 2150000))
657 		return -EINVAL;
658 
659 	div = (p->frequency + (500 - 1)) / 500;	/* round correctly */
660 	buf[0] = (div >> 8) & 0x7f;
661 	buf[1] = div & 0xff;
662 	buf[2] = 0x80 | ((div & 0x18000) >> 10) | 2;
663 	buf[3] = 0x20;
664 
665 	if (p->symbol_rate < 4000000)
666 		buf[3] |= 1;
667 
668 	if (p->frequency < 1250000)
669 		buf[3] |= 0;
670 	else if (p->frequency < 1550000)
671 		buf[3] |= 0x40;
672 	else if (p->frequency < 2050000)
673 		buf[3] |= 0x80;
674 	else if (p->frequency < 2150000)
675 		buf[3] |= 0xC0;
676 
677 	if (fe->ops.i2c_gate_ctrl)
678 		fe->ops.i2c_gate_ctrl(fe, 1);
679 	if (i2c_transfer(&budget_ci->budget.i2c_adap, &msg, 1) != 1)
680 		return -EIO;
681 	return 0;
682 }
683 
684 static const struct stv0299_config philips_su1278_tt_config = {
685 
686 	.demod_address = 0x68,
687 	.inittab = philips_su1278_tt_inittab,
688 	.mclk = 64000000UL,
689 	.invert = 0,
690 	.skip_reinit = 1,
691 	.lock_output = STV0299_LOCKOUTPUT_1,
692 	.volt13_op0_op1 = STV0299_VOLT13_OP1,
693 	.min_delay_ms = 50,
694 	.set_symbol_rate = philips_su1278_tt_set_symbol_rate,
695 };
696 
697 
698 
699 static int philips_tdm1316l_tuner_init(struct dvb_frontend *fe)
700 {
701 	struct budget_ci *budget_ci = (struct budget_ci *) fe->dvb->priv;
702 	static u8 td1316_init[] = { 0x0b, 0xf5, 0x85, 0xab };
703 	static u8 disable_mc44BC374c[] = { 0x1d, 0x74, 0xa0, 0x68 };
704 	struct i2c_msg tuner_msg = {.addr = budget_ci->tuner_pll_address,.flags = 0,.buf = td1316_init,.len =
705 			sizeof(td1316_init) };
706 
707 	// setup PLL configuration
708 	if (fe->ops.i2c_gate_ctrl)
709 		fe->ops.i2c_gate_ctrl(fe, 1);
710 	if (i2c_transfer(&budget_ci->budget.i2c_adap, &tuner_msg, 1) != 1)
711 		return -EIO;
712 	msleep(1);
713 
714 	// disable the mc44BC374c (do not check for errors)
715 	tuner_msg.addr = 0x65;
716 	tuner_msg.buf = disable_mc44BC374c;
717 	tuner_msg.len = sizeof(disable_mc44BC374c);
718 	if (fe->ops.i2c_gate_ctrl)
719 		fe->ops.i2c_gate_ctrl(fe, 1);
720 	if (i2c_transfer(&budget_ci->budget.i2c_adap, &tuner_msg, 1) != 1) {
721 		if (fe->ops.i2c_gate_ctrl)
722 			fe->ops.i2c_gate_ctrl(fe, 1);
723 		i2c_transfer(&budget_ci->budget.i2c_adap, &tuner_msg, 1);
724 	}
725 
726 	return 0;
727 }
728 
729 static int philips_tdm1316l_tuner_set_params(struct dvb_frontend *fe)
730 {
731 	struct dtv_frontend_properties *p = &fe->dtv_property_cache;
732 	struct budget_ci *budget_ci = (struct budget_ci *) fe->dvb->priv;
733 	u8 tuner_buf[4];
734 	struct i2c_msg tuner_msg = {.addr = budget_ci->tuner_pll_address,.flags = 0,.buf = tuner_buf,.len = sizeof(tuner_buf) };
735 	int tuner_frequency = 0;
736 	u8 band, cp, filter;
737 
738 	// determine charge pump
739 	tuner_frequency = p->frequency + 36130000;
740 	if (tuner_frequency < 87000000)
741 		return -EINVAL;
742 	else if (tuner_frequency < 130000000)
743 		cp = 3;
744 	else if (tuner_frequency < 160000000)
745 		cp = 5;
746 	else if (tuner_frequency < 200000000)
747 		cp = 6;
748 	else if (tuner_frequency < 290000000)
749 		cp = 3;
750 	else if (tuner_frequency < 420000000)
751 		cp = 5;
752 	else if (tuner_frequency < 480000000)
753 		cp = 6;
754 	else if (tuner_frequency < 620000000)
755 		cp = 3;
756 	else if (tuner_frequency < 830000000)
757 		cp = 5;
758 	else if (tuner_frequency < 895000000)
759 		cp = 7;
760 	else
761 		return -EINVAL;
762 
763 	// determine band
764 	if (p->frequency < 49000000)
765 		return -EINVAL;
766 	else if (p->frequency < 159000000)
767 		band = 1;
768 	else if (p->frequency < 444000000)
769 		band = 2;
770 	else if (p->frequency < 861000000)
771 		band = 4;
772 	else
773 		return -EINVAL;
774 
775 	// setup PLL filter and TDA9889
776 	switch (p->bandwidth_hz) {
777 	case 6000000:
778 		tda1004x_writereg(fe, 0x0C, 0x14);
779 		filter = 0;
780 		break;
781 
782 	case 7000000:
783 		tda1004x_writereg(fe, 0x0C, 0x80);
784 		filter = 0;
785 		break;
786 
787 	case 8000000:
788 		tda1004x_writereg(fe, 0x0C, 0x14);
789 		filter = 1;
790 		break;
791 
792 	default:
793 		return -EINVAL;
794 	}
795 
796 	// calculate divisor
797 	// ((36130000+((1000000/6)/2)) + Finput)/(1000000/6)
798 	tuner_frequency = (((p->frequency / 1000) * 6) + 217280) / 1000;
799 
800 	// setup tuner buffer
801 	tuner_buf[0] = tuner_frequency >> 8;
802 	tuner_buf[1] = tuner_frequency & 0xff;
803 	tuner_buf[2] = 0xca;
804 	tuner_buf[3] = (cp << 5) | (filter << 3) | band;
805 
806 	if (fe->ops.i2c_gate_ctrl)
807 		fe->ops.i2c_gate_ctrl(fe, 1);
808 	if (i2c_transfer(&budget_ci->budget.i2c_adap, &tuner_msg, 1) != 1)
809 		return -EIO;
810 
811 	msleep(1);
812 	return 0;
813 }
814 
815 static int philips_tdm1316l_request_firmware(struct dvb_frontend *fe,
816 					     const struct firmware **fw, char *name)
817 {
818 	struct budget_ci *budget_ci = (struct budget_ci *) fe->dvb->priv;
819 
820 	return request_firmware(fw, name, &budget_ci->budget.dev->pci->dev);
821 }
822 
823 static struct tda1004x_config philips_tdm1316l_config = {
824 
825 	.demod_address = 0x8,
826 	.invert = 0,
827 	.invert_oclk = 0,
828 	.xtal_freq = TDA10046_XTAL_4M,
829 	.agc_config = TDA10046_AGC_DEFAULT,
830 	.if_freq = TDA10046_FREQ_3617,
831 	.request_firmware = philips_tdm1316l_request_firmware,
832 };
833 
834 static struct tda1004x_config philips_tdm1316l_config_invert = {
835 
836 	.demod_address = 0x8,
837 	.invert = 1,
838 	.invert_oclk = 0,
839 	.xtal_freq = TDA10046_XTAL_4M,
840 	.agc_config = TDA10046_AGC_DEFAULT,
841 	.if_freq = TDA10046_FREQ_3617,
842 	.request_firmware = philips_tdm1316l_request_firmware,
843 };
844 
845 static int dvbc_philips_tdm1316l_tuner_set_params(struct dvb_frontend *fe)
846 {
847 	struct dtv_frontend_properties *p = &fe->dtv_property_cache;
848 	struct budget_ci *budget_ci = (struct budget_ci *) fe->dvb->priv;
849 	u8 tuner_buf[5];
850 	struct i2c_msg tuner_msg = {.addr = budget_ci->tuner_pll_address,
851 				    .flags = 0,
852 				    .buf = tuner_buf,
853 				    .len = sizeof(tuner_buf) };
854 	int tuner_frequency = 0;
855 	u8 band, cp, filter;
856 
857 	// determine charge pump
858 	tuner_frequency = p->frequency + 36125000;
859 	if (tuner_frequency < 87000000)
860 		return -EINVAL;
861 	else if (tuner_frequency < 130000000) {
862 		cp = 3;
863 		band = 1;
864 	} else if (tuner_frequency < 160000000) {
865 		cp = 5;
866 		band = 1;
867 	} else if (tuner_frequency < 200000000) {
868 		cp = 6;
869 		band = 1;
870 	} else if (tuner_frequency < 290000000) {
871 		cp = 3;
872 		band = 2;
873 	} else if (tuner_frequency < 420000000) {
874 		cp = 5;
875 		band = 2;
876 	} else if (tuner_frequency < 480000000) {
877 		cp = 6;
878 		band = 2;
879 	} else if (tuner_frequency < 620000000) {
880 		cp = 3;
881 		band = 4;
882 	} else if (tuner_frequency < 830000000) {
883 		cp = 5;
884 		band = 4;
885 	} else if (tuner_frequency < 895000000) {
886 		cp = 7;
887 		band = 4;
888 	} else
889 		return -EINVAL;
890 
891 	// assume PLL filter should always be 8MHz for the moment.
892 	filter = 1;
893 
894 	// calculate divisor
895 	tuner_frequency = (p->frequency + 36125000 + (62500/2)) / 62500;
896 
897 	// setup tuner buffer
898 	tuner_buf[0] = tuner_frequency >> 8;
899 	tuner_buf[1] = tuner_frequency & 0xff;
900 	tuner_buf[2] = 0xc8;
901 	tuner_buf[3] = (cp << 5) | (filter << 3) | band;
902 	tuner_buf[4] = 0x80;
903 
904 	if (fe->ops.i2c_gate_ctrl)
905 		fe->ops.i2c_gate_ctrl(fe, 1);
906 	if (i2c_transfer(&budget_ci->budget.i2c_adap, &tuner_msg, 1) != 1)
907 		return -EIO;
908 
909 	msleep(50);
910 
911 	if (fe->ops.i2c_gate_ctrl)
912 		fe->ops.i2c_gate_ctrl(fe, 1);
913 	if (i2c_transfer(&budget_ci->budget.i2c_adap, &tuner_msg, 1) != 1)
914 		return -EIO;
915 
916 	msleep(1);
917 
918 	return 0;
919 }
920 
921 static u8 dvbc_philips_tdm1316l_inittab[] = {
922 	0x80, 0x01,
923 	0x80, 0x00,
924 	0x81, 0x01,
925 	0x81, 0x00,
926 	0x00, 0x09,
927 	0x01, 0x69,
928 	0x03, 0x00,
929 	0x04, 0x00,
930 	0x07, 0x00,
931 	0x08, 0x00,
932 	0x20, 0x00,
933 	0x21, 0x40,
934 	0x22, 0x00,
935 	0x23, 0x00,
936 	0x24, 0x40,
937 	0x25, 0x88,
938 	0x30, 0xff,
939 	0x31, 0x00,
940 	0x32, 0xff,
941 	0x33, 0x00,
942 	0x34, 0x50,
943 	0x35, 0x7f,
944 	0x36, 0x00,
945 	0x37, 0x20,
946 	0x38, 0x00,
947 	0x40, 0x1c,
948 	0x41, 0xff,
949 	0x42, 0x29,
950 	0x43, 0x20,
951 	0x44, 0xff,
952 	0x45, 0x00,
953 	0x46, 0x00,
954 	0x49, 0x04,
955 	0x4a, 0x00,
956 	0x4b, 0x7b,
957 	0x52, 0x30,
958 	0x55, 0xae,
959 	0x56, 0x47,
960 	0x57, 0xe1,
961 	0x58, 0x3a,
962 	0x5a, 0x1e,
963 	0x5b, 0x34,
964 	0x60, 0x00,
965 	0x63, 0x00,
966 	0x64, 0x00,
967 	0x65, 0x00,
968 	0x66, 0x00,
969 	0x67, 0x00,
970 	0x68, 0x00,
971 	0x69, 0x00,
972 	0x6a, 0x02,
973 	0x6b, 0x00,
974 	0x70, 0xff,
975 	0x71, 0x00,
976 	0x72, 0x00,
977 	0x73, 0x00,
978 	0x74, 0x0c,
979 	0x80, 0x00,
980 	0x81, 0x00,
981 	0x82, 0x00,
982 	0x83, 0x00,
983 	0x84, 0x04,
984 	0x85, 0x80,
985 	0x86, 0x24,
986 	0x87, 0x78,
987 	0x88, 0x10,
988 	0x89, 0x00,
989 	0x90, 0x01,
990 	0x91, 0x01,
991 	0xa0, 0x04,
992 	0xa1, 0x00,
993 	0xa2, 0x00,
994 	0xb0, 0x91,
995 	0xb1, 0x0b,
996 	0xc0, 0x53,
997 	0xc1, 0x70,
998 	0xc2, 0x12,
999 	0xd0, 0x00,
1000 	0xd1, 0x00,
1001 	0xd2, 0x00,
1002 	0xd3, 0x00,
1003 	0xd4, 0x00,
1004 	0xd5, 0x00,
1005 	0xde, 0x00,
1006 	0xdf, 0x00,
1007 	0x61, 0x38,
1008 	0x62, 0x0a,
1009 	0x53, 0x13,
1010 	0x59, 0x08,
1011 	0xff, 0xff,
1012 };
1013 
1014 static struct stv0297_config dvbc_philips_tdm1316l_config = {
1015 	.demod_address = 0x1c,
1016 	.inittab = dvbc_philips_tdm1316l_inittab,
1017 	.invert = 0,
1018 	.stop_during_read = 1,
1019 };
1020 
1021 static struct tda10023_config tda10023_config = {
1022 	.demod_address = 0xc,
1023 	.invert = 0,
1024 	.xtal = 16000000,
1025 	.pll_m = 11,
1026 	.pll_p = 3,
1027 	.pll_n = 1,
1028 	.deltaf = 0xa511,
1029 };
1030 
1031 static struct tda827x_config tda827x_config = {
1032 	.config = 0,
1033 };
1034 
1035 /* TT S2-3200 DVB-S (STB0899) Inittab */
1036 static const struct stb0899_s1_reg tt3200_stb0899_s1_init_1[] = {
1037 
1038 	{ STB0899_DEV_ID		, 0x81 },
1039 	{ STB0899_DISCNTRL1		, 0x32 },
1040 	{ STB0899_DISCNTRL2		, 0x80 },
1041 	{ STB0899_DISRX_ST0		, 0x04 },
1042 	{ STB0899_DISRX_ST1		, 0x00 },
1043 	{ STB0899_DISPARITY		, 0x00 },
1044 	{ STB0899_DISSTATUS		, 0x20 },
1045 	{ STB0899_DISF22		, 0x8c },
1046 	{ STB0899_DISF22RX		, 0x9a },
1047 	{ STB0899_SYSREG		, 0x0b },
1048 	{ STB0899_ACRPRESC		, 0x11 },
1049 	{ STB0899_ACRDIV1		, 0x0a },
1050 	{ STB0899_ACRDIV2		, 0x05 },
1051 	{ STB0899_DACR1			, 0x00 },
1052 	{ STB0899_DACR2			, 0x00 },
1053 	{ STB0899_OUTCFG		, 0x00 },
1054 	{ STB0899_MODECFG		, 0x00 },
1055 	{ STB0899_IRQSTATUS_3		, 0x30 },
1056 	{ STB0899_IRQSTATUS_2		, 0x00 },
1057 	{ STB0899_IRQSTATUS_1		, 0x00 },
1058 	{ STB0899_IRQSTATUS_0		, 0x00 },
1059 	{ STB0899_IRQMSK_3		, 0xf3 },
1060 	{ STB0899_IRQMSK_2		, 0xfc },
1061 	{ STB0899_IRQMSK_1		, 0xff },
1062 	{ STB0899_IRQMSK_0		, 0xff },
1063 	{ STB0899_IRQCFG		, 0x00 },
1064 	{ STB0899_I2CCFG		, 0x88 },
1065 	{ STB0899_I2CRPT		, 0x48 }, /* 12k Pullup, Repeater=16, Stop=disabled */
1066 	{ STB0899_IOPVALUE5		, 0x00 },
1067 	{ STB0899_IOPVALUE4		, 0x20 },
1068 	{ STB0899_IOPVALUE3		, 0xc9 },
1069 	{ STB0899_IOPVALUE2		, 0x90 },
1070 	{ STB0899_IOPVALUE1		, 0x40 },
1071 	{ STB0899_IOPVALUE0		, 0x00 },
1072 	{ STB0899_GPIO00CFG		, 0x82 },
1073 	{ STB0899_GPIO01CFG		, 0x82 },
1074 	{ STB0899_GPIO02CFG		, 0x82 },
1075 	{ STB0899_GPIO03CFG		, 0x82 },
1076 	{ STB0899_GPIO04CFG		, 0x82 },
1077 	{ STB0899_GPIO05CFG		, 0x82 },
1078 	{ STB0899_GPIO06CFG		, 0x82 },
1079 	{ STB0899_GPIO07CFG		, 0x82 },
1080 	{ STB0899_GPIO08CFG		, 0x82 },
1081 	{ STB0899_GPIO09CFG		, 0x82 },
1082 	{ STB0899_GPIO10CFG		, 0x82 },
1083 	{ STB0899_GPIO11CFG		, 0x82 },
1084 	{ STB0899_GPIO12CFG		, 0x82 },
1085 	{ STB0899_GPIO13CFG		, 0x82 },
1086 	{ STB0899_GPIO14CFG		, 0x82 },
1087 	{ STB0899_GPIO15CFG		, 0x82 },
1088 	{ STB0899_GPIO16CFG		, 0x82 },
1089 	{ STB0899_GPIO17CFG		, 0x82 },
1090 	{ STB0899_GPIO18CFG		, 0x82 },
1091 	{ STB0899_GPIO19CFG		, 0x82 },
1092 	{ STB0899_GPIO20CFG		, 0x82 },
1093 	{ STB0899_SDATCFG		, 0xb8 },
1094 	{ STB0899_SCLTCFG		, 0xba },
1095 	{ STB0899_AGCRFCFG		, 0x1c }, /* 0x11 */
1096 	{ STB0899_GPIO22		, 0x82 }, /* AGCBB2CFG */
1097 	{ STB0899_GPIO21		, 0x91 }, /* AGCBB1CFG */
1098 	{ STB0899_DIRCLKCFG		, 0x82 },
1099 	{ STB0899_CLKOUT27CFG		, 0x7e },
1100 	{ STB0899_STDBYCFG		, 0x82 },
1101 	{ STB0899_CS0CFG		, 0x82 },
1102 	{ STB0899_CS1CFG		, 0x82 },
1103 	{ STB0899_DISEQCOCFG		, 0x20 },
1104 	{ STB0899_GPIO32CFG		, 0x82 },
1105 	{ STB0899_GPIO33CFG		, 0x82 },
1106 	{ STB0899_GPIO34CFG		, 0x82 },
1107 	{ STB0899_GPIO35CFG		, 0x82 },
1108 	{ STB0899_GPIO36CFG		, 0x82 },
1109 	{ STB0899_GPIO37CFG		, 0x82 },
1110 	{ STB0899_GPIO38CFG		, 0x82 },
1111 	{ STB0899_GPIO39CFG		, 0x82 },
1112 	{ STB0899_NCOARSE		, 0x15 }, /* 0x15 = 27 Mhz Clock, F/3 = 198MHz, F/6 = 99MHz */
1113 	{ STB0899_SYNTCTRL		, 0x02 }, /* 0x00 = CLK from CLKI, 0x02 = CLK from XTALI */
1114 	{ STB0899_FILTCTRL		, 0x00 },
1115 	{ STB0899_SYSCTRL		, 0x00 },
1116 	{ STB0899_STOPCLK1		, 0x20 },
1117 	{ STB0899_STOPCLK2		, 0x00 },
1118 	{ STB0899_INTBUFSTATUS		, 0x00 },
1119 	{ STB0899_INTBUFCTRL		, 0x0a },
1120 	{ 0xffff			, 0xff },
1121 };
1122 
1123 static const struct stb0899_s1_reg tt3200_stb0899_s1_init_3[] = {
1124 	{ STB0899_DEMOD			, 0x00 },
1125 	{ STB0899_RCOMPC		, 0xc9 },
1126 	{ STB0899_AGC1CN		, 0x41 },
1127 	{ STB0899_AGC1REF		, 0x10 },
1128 	{ STB0899_RTC			, 0x7a },
1129 	{ STB0899_TMGCFG		, 0x4e },
1130 	{ STB0899_AGC2REF		, 0x34 },
1131 	{ STB0899_TLSR			, 0x84 },
1132 	{ STB0899_CFD			, 0xc7 },
1133 	{ STB0899_ACLC			, 0x87 },
1134 	{ STB0899_BCLC			, 0x94 },
1135 	{ STB0899_EQON			, 0x41 },
1136 	{ STB0899_LDT			, 0xdd },
1137 	{ STB0899_LDT2			, 0xc9 },
1138 	{ STB0899_EQUALREF		, 0xb4 },
1139 	{ STB0899_TMGRAMP		, 0x10 },
1140 	{ STB0899_TMGTHD		, 0x30 },
1141 	{ STB0899_IDCCOMP		, 0xfb },
1142 	{ STB0899_QDCCOMP		, 0x03 },
1143 	{ STB0899_POWERI		, 0x3b },
1144 	{ STB0899_POWERQ		, 0x3d },
1145 	{ STB0899_RCOMP			, 0x81 },
1146 	{ STB0899_AGCIQIN		, 0x80 },
1147 	{ STB0899_AGC2I1		, 0x04 },
1148 	{ STB0899_AGC2I2		, 0xf5 },
1149 	{ STB0899_TLIR			, 0x25 },
1150 	{ STB0899_RTF			, 0x80 },
1151 	{ STB0899_DSTATUS		, 0x00 },
1152 	{ STB0899_LDI			, 0xca },
1153 	{ STB0899_CFRM			, 0xf1 },
1154 	{ STB0899_CFRL			, 0xf3 },
1155 	{ STB0899_NIRM			, 0x2a },
1156 	{ STB0899_NIRL			, 0x05 },
1157 	{ STB0899_ISYMB			, 0x17 },
1158 	{ STB0899_QSYMB			, 0xfa },
1159 	{ STB0899_SFRH			, 0x2f },
1160 	{ STB0899_SFRM			, 0x68 },
1161 	{ STB0899_SFRL			, 0x40 },
1162 	{ STB0899_SFRUPH		, 0x2f },
1163 	{ STB0899_SFRUPM		, 0x68 },
1164 	{ STB0899_SFRUPL		, 0x40 },
1165 	{ STB0899_EQUAI1		, 0xfd },
1166 	{ STB0899_EQUAQ1		, 0x04 },
1167 	{ STB0899_EQUAI2		, 0x0f },
1168 	{ STB0899_EQUAQ2		, 0xff },
1169 	{ STB0899_EQUAI3		, 0xdf },
1170 	{ STB0899_EQUAQ3		, 0xfa },
1171 	{ STB0899_EQUAI4		, 0x37 },
1172 	{ STB0899_EQUAQ4		, 0x0d },
1173 	{ STB0899_EQUAI5		, 0xbd },
1174 	{ STB0899_EQUAQ5		, 0xf7 },
1175 	{ STB0899_DSTATUS2		, 0x00 },
1176 	{ STB0899_VSTATUS		, 0x00 },
1177 	{ STB0899_VERROR		, 0xff },
1178 	{ STB0899_IQSWAP		, 0x2a },
1179 	{ STB0899_ECNT1M		, 0x00 },
1180 	{ STB0899_ECNT1L		, 0x00 },
1181 	{ STB0899_ECNT2M		, 0x00 },
1182 	{ STB0899_ECNT2L		, 0x00 },
1183 	{ STB0899_ECNT3M		, 0x00 },
1184 	{ STB0899_ECNT3L		, 0x00 },
1185 	{ STB0899_FECAUTO1		, 0x06 },
1186 	{ STB0899_FECM			, 0x01 },
1187 	{ STB0899_VTH12			, 0xf0 },
1188 	{ STB0899_VTH23			, 0xa0 },
1189 	{ STB0899_VTH34			, 0x78 },
1190 	{ STB0899_VTH56			, 0x4e },
1191 	{ STB0899_VTH67			, 0x48 },
1192 	{ STB0899_VTH78			, 0x38 },
1193 	{ STB0899_PRVIT			, 0xff },
1194 	{ STB0899_VITSYNC		, 0x19 },
1195 	{ STB0899_RSULC			, 0xb1 }, /* DVB = 0xb1, DSS = 0xa1 */
1196 	{ STB0899_TSULC			, 0x42 },
1197 	{ STB0899_RSLLC			, 0x40 },
1198 	{ STB0899_TSLPL			, 0x12 },
1199 	{ STB0899_TSCFGH		, 0x0c },
1200 	{ STB0899_TSCFGM		, 0x00 },
1201 	{ STB0899_TSCFGL		, 0x0c },
1202 	{ STB0899_TSOUT			, 0x4d }, /* 0x0d for CAM */
1203 	{ STB0899_RSSYNCDEL		, 0x00 },
1204 	{ STB0899_TSINHDELH		, 0x02 },
1205 	{ STB0899_TSINHDELM		, 0x00 },
1206 	{ STB0899_TSINHDELL		, 0x00 },
1207 	{ STB0899_TSLLSTKM		, 0x00 },
1208 	{ STB0899_TSLLSTKL		, 0x00 },
1209 	{ STB0899_TSULSTKM		, 0x00 },
1210 	{ STB0899_TSULSTKL		, 0xab },
1211 	{ STB0899_PCKLENUL		, 0x00 },
1212 	{ STB0899_PCKLENLL		, 0xcc },
1213 	{ STB0899_RSPCKLEN		, 0xcc },
1214 	{ STB0899_TSSTATUS		, 0x80 },
1215 	{ STB0899_ERRCTRL1		, 0xb6 },
1216 	{ STB0899_ERRCTRL2		, 0x96 },
1217 	{ STB0899_ERRCTRL3		, 0x89 },
1218 	{ STB0899_DMONMSK1		, 0x27 },
1219 	{ STB0899_DMONMSK0		, 0x03 },
1220 	{ STB0899_DEMAPVIT		, 0x5c },
1221 	{ STB0899_PLPARM		, 0x1f },
1222 	{ STB0899_PDELCTRL		, 0x48 },
1223 	{ STB0899_PDELCTRL2		, 0x00 },
1224 	{ STB0899_BBHCTRL1		, 0x00 },
1225 	{ STB0899_BBHCTRL2		, 0x00 },
1226 	{ STB0899_HYSTTHRESH		, 0x77 },
1227 	{ STB0899_MATCSTM		, 0x00 },
1228 	{ STB0899_MATCSTL		, 0x00 },
1229 	{ STB0899_UPLCSTM		, 0x00 },
1230 	{ STB0899_UPLCSTL		, 0x00 },
1231 	{ STB0899_DFLCSTM		, 0x00 },
1232 	{ STB0899_DFLCSTL		, 0x00 },
1233 	{ STB0899_SYNCCST		, 0x00 },
1234 	{ STB0899_SYNCDCSTM		, 0x00 },
1235 	{ STB0899_SYNCDCSTL		, 0x00 },
1236 	{ STB0899_ISI_ENTRY		, 0x00 },
1237 	{ STB0899_ISI_BIT_EN		, 0x00 },
1238 	{ STB0899_MATSTRM		, 0x00 },
1239 	{ STB0899_MATSTRL		, 0x00 },
1240 	{ STB0899_UPLSTRM		, 0x00 },
1241 	{ STB0899_UPLSTRL		, 0x00 },
1242 	{ STB0899_DFLSTRM		, 0x00 },
1243 	{ STB0899_DFLSTRL		, 0x00 },
1244 	{ STB0899_SYNCSTR		, 0x00 },
1245 	{ STB0899_SYNCDSTRM		, 0x00 },
1246 	{ STB0899_SYNCDSTRL		, 0x00 },
1247 	{ STB0899_CFGPDELSTATUS1	, 0x10 },
1248 	{ STB0899_CFGPDELSTATUS2	, 0x00 },
1249 	{ STB0899_BBFERRORM		, 0x00 },
1250 	{ STB0899_BBFERRORL		, 0x00 },
1251 	{ STB0899_UPKTERRORM		, 0x00 },
1252 	{ STB0899_UPKTERRORL		, 0x00 },
1253 	{ 0xffff			, 0xff },
1254 };
1255 
1256 static struct stb0899_config tt3200_config = {
1257 	.init_dev		= tt3200_stb0899_s1_init_1,
1258 	.init_s2_demod		= stb0899_s2_init_2,
1259 	.init_s1_demod		= tt3200_stb0899_s1_init_3,
1260 	.init_s2_fec		= stb0899_s2_init_4,
1261 	.init_tst		= stb0899_s1_init_5,
1262 
1263 	.postproc		= NULL,
1264 
1265 	.demod_address		= 0x68,
1266 
1267 	.xtal_freq		= 27000000,
1268 	.inversion		= IQ_SWAP_ON,
1269 
1270 	.lo_clk			= 76500000,
1271 	.hi_clk			= 99000000,
1272 
1273 	.esno_ave		= STB0899_DVBS2_ESNO_AVE,
1274 	.esno_quant		= STB0899_DVBS2_ESNO_QUANT,
1275 	.avframes_coarse	= STB0899_DVBS2_AVFRAMES_COARSE,
1276 	.avframes_fine		= STB0899_DVBS2_AVFRAMES_FINE,
1277 	.miss_threshold		= STB0899_DVBS2_MISS_THRESHOLD,
1278 	.uwp_threshold_acq	= STB0899_DVBS2_UWP_THRESHOLD_ACQ,
1279 	.uwp_threshold_track	= STB0899_DVBS2_UWP_THRESHOLD_TRACK,
1280 	.uwp_threshold_sof	= STB0899_DVBS2_UWP_THRESHOLD_SOF,
1281 	.sof_search_timeout	= STB0899_DVBS2_SOF_SEARCH_TIMEOUT,
1282 
1283 	.btr_nco_bits		= STB0899_DVBS2_BTR_NCO_BITS,
1284 	.btr_gain_shift_offset	= STB0899_DVBS2_BTR_GAIN_SHIFT_OFFSET,
1285 	.crl_nco_bits		= STB0899_DVBS2_CRL_NCO_BITS,
1286 	.ldpc_max_iter		= STB0899_DVBS2_LDPC_MAX_ITER,
1287 
1288 	.tuner_get_frequency	= stb6100_get_frequency,
1289 	.tuner_set_frequency	= stb6100_set_frequency,
1290 	.tuner_set_bandwidth	= stb6100_set_bandwidth,
1291 	.tuner_get_bandwidth	= stb6100_get_bandwidth,
1292 	.tuner_set_rfsiggain	= NULL
1293 };
1294 
1295 static struct stb6100_config tt3200_stb6100_config = {
1296 	.tuner_address	= 0x60,
1297 	.refclock	= 27000000,
1298 };
1299 
1300 static void frontend_init(struct budget_ci *budget_ci)
1301 {
1302 	switch (budget_ci->budget.dev->pci->subsystem_device) {
1303 	case 0x100c:		// Hauppauge/TT Nova-CI budget (stv0299/ALPS BSRU6(tsa5059))
1304 		budget_ci->budget.dvb_frontend =
1305 			dvb_attach(stv0299_attach, &alps_bsru6_config, &budget_ci->budget.i2c_adap);
1306 		if (budget_ci->budget.dvb_frontend) {
1307 			budget_ci->budget.dvb_frontend->ops.tuner_ops.set_params = alps_bsru6_tuner_set_params;
1308 			budget_ci->budget.dvb_frontend->tuner_priv = &budget_ci->budget.i2c_adap;
1309 			break;
1310 		}
1311 		break;
1312 
1313 	case 0x100f:		// Hauppauge/TT Nova-CI budget (stv0299b/Philips su1278(tsa5059))
1314 		budget_ci->budget.dvb_frontend =
1315 			dvb_attach(stv0299_attach, &philips_su1278_tt_config, &budget_ci->budget.i2c_adap);
1316 		if (budget_ci->budget.dvb_frontend) {
1317 			budget_ci->budget.dvb_frontend->ops.tuner_ops.set_params = philips_su1278_tt_tuner_set_params;
1318 			break;
1319 		}
1320 		break;
1321 
1322 	case 0x1010:		// TT DVB-C CI budget (stv0297/Philips tdm1316l(tda6651tt))
1323 		budget_ci->tuner_pll_address = 0x61;
1324 		budget_ci->budget.dvb_frontend =
1325 			dvb_attach(stv0297_attach, &dvbc_philips_tdm1316l_config, &budget_ci->budget.i2c_adap);
1326 		if (budget_ci->budget.dvb_frontend) {
1327 			budget_ci->budget.dvb_frontend->ops.tuner_ops.set_params = dvbc_philips_tdm1316l_tuner_set_params;
1328 			break;
1329 		}
1330 		break;
1331 
1332 	case 0x1011:		// Hauppauge/TT Nova-T budget (tda10045/Philips tdm1316l(tda6651tt) + TDA9889)
1333 		budget_ci->tuner_pll_address = 0x63;
1334 		budget_ci->budget.dvb_frontend =
1335 			dvb_attach(tda10045_attach, &philips_tdm1316l_config, &budget_ci->budget.i2c_adap);
1336 		if (budget_ci->budget.dvb_frontend) {
1337 			budget_ci->budget.dvb_frontend->ops.tuner_ops.init = philips_tdm1316l_tuner_init;
1338 			budget_ci->budget.dvb_frontend->ops.tuner_ops.set_params = philips_tdm1316l_tuner_set_params;
1339 			break;
1340 		}
1341 		break;
1342 
1343 	case 0x1012:		// TT DVB-T CI budget (tda10046/Philips tdm1316l(tda6651tt))
1344 		budget_ci->tuner_pll_address = 0x60;
1345 		budget_ci->budget.dvb_frontend =
1346 			dvb_attach(tda10046_attach, &philips_tdm1316l_config_invert, &budget_ci->budget.i2c_adap);
1347 		if (budget_ci->budget.dvb_frontend) {
1348 			budget_ci->budget.dvb_frontend->ops.tuner_ops.init = philips_tdm1316l_tuner_init;
1349 			budget_ci->budget.dvb_frontend->ops.tuner_ops.set_params = philips_tdm1316l_tuner_set_params;
1350 			break;
1351 		}
1352 		break;
1353 
1354 	case 0x1017:		// TT S-1500 PCI
1355 		budget_ci->budget.dvb_frontend = dvb_attach(stv0299_attach, &alps_bsbe1_config, &budget_ci->budget.i2c_adap);
1356 		if (budget_ci->budget.dvb_frontend) {
1357 			budget_ci->budget.dvb_frontend->ops.tuner_ops.set_params = alps_bsbe1_tuner_set_params;
1358 			budget_ci->budget.dvb_frontend->tuner_priv = &budget_ci->budget.i2c_adap;
1359 
1360 			budget_ci->budget.dvb_frontend->ops.dishnetwork_send_legacy_command = NULL;
1361 			if (dvb_attach(lnbp21_attach, budget_ci->budget.dvb_frontend, &budget_ci->budget.i2c_adap, LNBP21_LLC, 0) == NULL) {
1362 				printk("%s: No LNBP21 found!\n", __func__);
1363 				dvb_frontend_detach(budget_ci->budget.dvb_frontend);
1364 				budget_ci->budget.dvb_frontend = NULL;
1365 			}
1366 		}
1367 		break;
1368 
1369 	case 0x101a: /* TT Budget-C-1501 (philips tda10023/philips tda8274A) */
1370 		budget_ci->budget.dvb_frontend = dvb_attach(tda10023_attach, &tda10023_config, &budget_ci->budget.i2c_adap, 0x48);
1371 		if (budget_ci->budget.dvb_frontend) {
1372 			if (dvb_attach(tda827x_attach, budget_ci->budget.dvb_frontend, 0x61, &budget_ci->budget.i2c_adap, &tda827x_config) == NULL) {
1373 				printk(KERN_ERR "%s: No tda827x found!\n", __func__);
1374 				dvb_frontend_detach(budget_ci->budget.dvb_frontend);
1375 				budget_ci->budget.dvb_frontend = NULL;
1376 			}
1377 		}
1378 		break;
1379 
1380 	case 0x101b: /* TT S-1500B (BSBE1-D01A - STV0288/STB6000/LNBP21) */
1381 		budget_ci->budget.dvb_frontend = dvb_attach(stv0288_attach, &stv0288_bsbe1_d01a_config, &budget_ci->budget.i2c_adap);
1382 		if (budget_ci->budget.dvb_frontend) {
1383 			if (dvb_attach(stb6000_attach, budget_ci->budget.dvb_frontend, 0x63, &budget_ci->budget.i2c_adap)) {
1384 				if (!dvb_attach(lnbp21_attach, budget_ci->budget.dvb_frontend, &budget_ci->budget.i2c_adap, 0, 0)) {
1385 					printk(KERN_ERR "%s: No LNBP21 found!\n", __func__);
1386 					dvb_frontend_detach(budget_ci->budget.dvb_frontend);
1387 					budget_ci->budget.dvb_frontend = NULL;
1388 				}
1389 			} else {
1390 				printk(KERN_ERR "%s: No STB6000 found!\n", __func__);
1391 				dvb_frontend_detach(budget_ci->budget.dvb_frontend);
1392 				budget_ci->budget.dvb_frontend = NULL;
1393 			}
1394 		}
1395 		break;
1396 
1397 	case 0x1019:		// TT S2-3200 PCI
1398 		/*
1399 		 * NOTE! on some STB0899 versions, the internal PLL takes a longer time
1400 		 * to settle, aka LOCK. On the older revisions of the chip, we don't see
1401 		 * this, as a result on the newer chips the entire clock tree, will not
1402 		 * be stable after a freshly POWER 'ed up situation.
1403 		 * In this case, we should RESET the STB0899 (Active LOW) and wait for
1404 		 * PLL stabilization.
1405 		 *
1406 		 * On the TT S2 3200 and clones, the STB0899 demodulator's RESETB is
1407 		 * connected to the SAA7146 GPIO, GPIO2, Pin 142
1408 		 */
1409 		/* Reset Demodulator */
1410 		saa7146_setgpio(budget_ci->budget.dev, 2, SAA7146_GPIO_OUTLO);
1411 		/* Wait for everything to die */
1412 		msleep(50);
1413 		/* Pull it up out of Reset state */
1414 		saa7146_setgpio(budget_ci->budget.dev, 2, SAA7146_GPIO_OUTHI);
1415 		/* Wait for PLL to stabilize */
1416 		msleep(250);
1417 		/*
1418 		 * PLL state should be stable now. Ideally, we should check
1419 		 * for PLL LOCK status. But well, never mind!
1420 		 */
1421 		budget_ci->budget.dvb_frontend = dvb_attach(stb0899_attach, &tt3200_config, &budget_ci->budget.i2c_adap);
1422 		if (budget_ci->budget.dvb_frontend) {
1423 			if (dvb_attach(stb6100_attach, budget_ci->budget.dvb_frontend, &tt3200_stb6100_config, &budget_ci->budget.i2c_adap)) {
1424 				if (!dvb_attach(lnbp21_attach, budget_ci->budget.dvb_frontend, &budget_ci->budget.i2c_adap, 0, 0)) {
1425 					printk("%s: No LNBP21 found!\n", __func__);
1426 					dvb_frontend_detach(budget_ci->budget.dvb_frontend);
1427 					budget_ci->budget.dvb_frontend = NULL;
1428 				}
1429 			} else {
1430 					dvb_frontend_detach(budget_ci->budget.dvb_frontend);
1431 					budget_ci->budget.dvb_frontend = NULL;
1432 			}
1433 		}
1434 		break;
1435 
1436 	}
1437 
1438 	if (budget_ci->budget.dvb_frontend == NULL) {
1439 		printk("budget-ci: A frontend driver was not found for device [%04x:%04x] subsystem [%04x:%04x]\n",
1440 		       budget_ci->budget.dev->pci->vendor,
1441 		       budget_ci->budget.dev->pci->device,
1442 		       budget_ci->budget.dev->pci->subsystem_vendor,
1443 		       budget_ci->budget.dev->pci->subsystem_device);
1444 	} else {
1445 		if (dvb_register_frontend
1446 		    (&budget_ci->budget.dvb_adapter, budget_ci->budget.dvb_frontend)) {
1447 			printk("budget-ci: Frontend registration failed!\n");
1448 			dvb_frontend_detach(budget_ci->budget.dvb_frontend);
1449 			budget_ci->budget.dvb_frontend = NULL;
1450 		}
1451 	}
1452 }
1453 
1454 static int budget_ci_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info)
1455 {
1456 	struct budget_ci *budget_ci;
1457 	int err;
1458 
1459 	budget_ci = kzalloc(sizeof(struct budget_ci), GFP_KERNEL);
1460 	if (!budget_ci) {
1461 		err = -ENOMEM;
1462 		goto out1;
1463 	}
1464 
1465 	dprintk(2, "budget_ci: %p\n", budget_ci);
1466 
1467 	dev->ext_priv = budget_ci;
1468 
1469 	err = ttpci_budget_init(&budget_ci->budget, dev, info, THIS_MODULE,
1470 				adapter_nr);
1471 	if (err)
1472 		goto out2;
1473 
1474 	err = msp430_ir_init(budget_ci);
1475 	if (err)
1476 		goto out3;
1477 
1478 	ciintf_init(budget_ci);
1479 
1480 	budget_ci->budget.dvb_adapter.priv = budget_ci;
1481 	frontend_init(budget_ci);
1482 
1483 	ttpci_budget_init_hooks(&budget_ci->budget);
1484 
1485 	return 0;
1486 
1487 out3:
1488 	ttpci_budget_deinit(&budget_ci->budget);
1489 out2:
1490 	kfree(budget_ci);
1491 out1:
1492 	return err;
1493 }
1494 
1495 static int budget_ci_detach(struct saa7146_dev *dev)
1496 {
1497 	struct budget_ci *budget_ci = (struct budget_ci *) dev->ext_priv;
1498 	struct saa7146_dev *saa = budget_ci->budget.dev;
1499 	int err;
1500 
1501 	if (budget_ci->budget.ci_present)
1502 		ciintf_deinit(budget_ci);
1503 	msp430_ir_deinit(budget_ci);
1504 	if (budget_ci->budget.dvb_frontend) {
1505 		dvb_unregister_frontend(budget_ci->budget.dvb_frontend);
1506 		dvb_frontend_detach(budget_ci->budget.dvb_frontend);
1507 	}
1508 	err = ttpci_budget_deinit(&budget_ci->budget);
1509 
1510 	// disable frontend and CI interface
1511 	saa7146_setgpio(saa, 2, SAA7146_GPIO_INPUT);
1512 
1513 	kfree(budget_ci);
1514 
1515 	return err;
1516 }
1517 
1518 static struct saa7146_extension budget_extension;
1519 
1520 MAKE_BUDGET_INFO(ttbs2, "TT-Budget/S-1500 PCI", BUDGET_TT);
1521 MAKE_BUDGET_INFO(ttbci, "TT-Budget/WinTV-NOVA-CI PCI", BUDGET_TT_HW_DISEQC);
1522 MAKE_BUDGET_INFO(ttbt2, "TT-Budget/WinTV-NOVA-T	 PCI", BUDGET_TT);
1523 MAKE_BUDGET_INFO(ttbtci, "TT-Budget-T-CI PCI", BUDGET_TT);
1524 MAKE_BUDGET_INFO(ttbcci, "TT-Budget-C-CI PCI", BUDGET_TT);
1525 MAKE_BUDGET_INFO(ttc1501, "TT-Budget C-1501 PCI", BUDGET_TT);
1526 MAKE_BUDGET_INFO(tt3200, "TT-Budget S2-3200 PCI", BUDGET_TT);
1527 MAKE_BUDGET_INFO(ttbs1500b, "TT-Budget S-1500B PCI", BUDGET_TT);
1528 
1529 static const struct pci_device_id pci_tbl[] = {
1530 	MAKE_EXTENSION_PCI(ttbci, 0x13c2, 0x100c),
1531 	MAKE_EXTENSION_PCI(ttbci, 0x13c2, 0x100f),
1532 	MAKE_EXTENSION_PCI(ttbcci, 0x13c2, 0x1010),
1533 	MAKE_EXTENSION_PCI(ttbt2, 0x13c2, 0x1011),
1534 	MAKE_EXTENSION_PCI(ttbtci, 0x13c2, 0x1012),
1535 	MAKE_EXTENSION_PCI(ttbs2, 0x13c2, 0x1017),
1536 	MAKE_EXTENSION_PCI(ttc1501, 0x13c2, 0x101a),
1537 	MAKE_EXTENSION_PCI(tt3200, 0x13c2, 0x1019),
1538 	MAKE_EXTENSION_PCI(ttbs1500b, 0x13c2, 0x101b),
1539 	{
1540 	 .vendor = 0,
1541 	 }
1542 };
1543 
1544 MODULE_DEVICE_TABLE(pci, pci_tbl);
1545 
1546 static struct saa7146_extension budget_extension = {
1547 	.name = "budget_ci dvb",
1548 	.flags = SAA7146_USE_I2C_IRQ,
1549 
1550 	.module = THIS_MODULE,
1551 	.pci_tbl = &pci_tbl[0],
1552 	.attach = budget_ci_attach,
1553 	.detach = budget_ci_detach,
1554 
1555 	.irq_mask = MASK_03 | MASK_06 | MASK_10,
1556 	.irq_func = budget_ci_irq,
1557 };
1558 
1559 static int __init budget_ci_init(void)
1560 {
1561 	return saa7146_register_extension(&budget_extension);
1562 }
1563 
1564 static void __exit budget_ci_exit(void)
1565 {
1566 	saa7146_unregister_extension(&budget_extension);
1567 }
1568 
1569 module_init(budget_ci_init);
1570 module_exit(budget_ci_exit);
1571 
1572 MODULE_LICENSE("GPL");
1573 MODULE_AUTHOR("Michael Hunold, Jack Thomasson, Andrew de Quincey, others");
1574 MODULE_DESCRIPTION("driver for the SAA7146 based so-called budget PCI DVB cards w/ CI-module produced by Siemens, Technotrend, Hauppauge");
1575