1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 4 bttv-cards.c 5 6 this file has configuration information - card-specific stuff 7 like the big tvcards array for the most part 8 9 Copyright (C) 1996,97,98 Ralph Metzler (rjkm@thp.uni-koeln.de) 10 & Marcus Metzler (mocm@thp.uni-koeln.de) 11 (c) 1999-2001 Gerd Knorr <kraxel@goldbach.in-berlin.de> 12 13 14 */ 15 16 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 17 18 #include <linux/delay.h> 19 #include <linux/module.h> 20 #include <linux/kmod.h> 21 #include <linux/init.h> 22 #include <linux/pci.h> 23 #include <linux/vmalloc.h> 24 #include <linux/firmware.h> 25 #include <net/checksum.h> 26 27 #include <asm/unaligned.h> 28 #include <asm/io.h> 29 30 #include "bttvp.h" 31 #include <media/v4l2-common.h> 32 #include <media/i2c/tvaudio.h> 33 #include "bttv-audio-hook.h" 34 35 /* fwd decl */ 36 static void boot_msp34xx(struct bttv *btv, int pin); 37 static void hauppauge_eeprom(struct bttv *btv); 38 static void avermedia_eeprom(struct bttv *btv); 39 static void osprey_eeprom(struct bttv *btv, const u8 ee[256]); 40 static void modtec_eeprom(struct bttv *btv); 41 static void init_PXC200(struct bttv *btv); 42 static void init_RTV24(struct bttv *btv); 43 static void init_PCI8604PW(struct bttv *btv); 44 45 static void rv605_muxsel(struct bttv *btv, unsigned int input); 46 static void eagle_muxsel(struct bttv *btv, unsigned int input); 47 static void xguard_muxsel(struct bttv *btv, unsigned int input); 48 static void ivc120_muxsel(struct bttv *btv, unsigned int input); 49 static void gvc1100_muxsel(struct bttv *btv, unsigned int input); 50 51 static void PXC200_muxsel(struct bttv *btv, unsigned int input); 52 53 static void picolo_tetra_muxsel(struct bttv *btv, unsigned int input); 54 static void picolo_tetra_init(struct bttv *btv); 55 56 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input); 57 static void tibetCS16_init(struct bttv *btv); 58 59 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input); 60 static void kodicom4400r_init(struct bttv *btv); 61 62 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input); 63 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input); 64 65 static void geovision_muxsel(struct bttv *btv, unsigned int input); 66 67 static void phytec_muxsel(struct bttv *btv, unsigned int input); 68 69 static void gv800s_muxsel(struct bttv *btv, unsigned int input); 70 static void gv800s_init(struct bttv *btv); 71 72 static void td3116_muxsel(struct bttv *btv, unsigned int input); 73 74 static int terratec_active_radio_upgrade(struct bttv *btv); 75 static int tea575x_init(struct bttv *btv); 76 static void identify_by_eeprom(struct bttv *btv, 77 unsigned char eeprom_data[256]); 78 static int pvr_boot(struct bttv *btv); 79 80 /* config variables */ 81 static unsigned int triton1; 82 static unsigned int vsfx; 83 static unsigned int latency = UNSET; 84 int no_overlay=-1; 85 86 static unsigned int card[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET }; 87 static unsigned int pll[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET }; 88 static unsigned int tuner[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET }; 89 static unsigned int svhs[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET }; 90 static unsigned int remote[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET }; 91 static unsigned int audiodev[BTTV_MAX]; 92 static unsigned int saa6588[BTTV_MAX]; 93 static struct bttv *master[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = NULL }; 94 static unsigned int autoload = UNSET; 95 static unsigned int gpiomask = UNSET; 96 static unsigned int audioall = UNSET; 97 static unsigned int audiomux[5] = { [ 0 ... 4 ] = UNSET }; 98 99 /* insmod options */ 100 module_param(triton1, int, 0444); 101 module_param(vsfx, int, 0444); 102 module_param(no_overlay, int, 0444); 103 module_param(latency, int, 0444); 104 module_param(gpiomask, int, 0444); 105 module_param(audioall, int, 0444); 106 module_param(autoload, int, 0444); 107 108 module_param_array(card, int, NULL, 0444); 109 module_param_array(pll, int, NULL, 0444); 110 module_param_array(tuner, int, NULL, 0444); 111 module_param_array(svhs, int, NULL, 0444); 112 module_param_array(remote, int, NULL, 0444); 113 module_param_array(audiodev, int, NULL, 0444); 114 module_param_array(audiomux, int, NULL, 0444); 115 116 MODULE_PARM_DESC(triton1, "set ETBF pci config bit [enable bug compatibility for triton1 + others]"); 117 MODULE_PARM_DESC(vsfx, "set VSFX pci config bit [yet another chipset flaw workaround]"); 118 MODULE_PARM_DESC(latency,"pci latency timer"); 119 MODULE_PARM_DESC(card,"specify TV/grabber card model, see CARDLIST file for a list"); 120 MODULE_PARM_DESC(pll, "specify installed crystal (0=none, 28=28 MHz, 35=35 MHz, 14=14 MHz)"); 121 MODULE_PARM_DESC(tuner,"specify installed tuner type"); 122 MODULE_PARM_DESC(autoload, "obsolete option, please do not use anymore"); 123 MODULE_PARM_DESC(audiodev, "specify audio device:\n" 124 "\t\t-1 = no audio\n" 125 "\t\t 0 = autodetect (default)\n" 126 "\t\t 1 = msp3400\n" 127 "\t\t 2 = tda7432\n" 128 "\t\t 3 = tvaudio"); 129 MODULE_PARM_DESC(saa6588, "if 1, then load the saa6588 RDS module, default (0) is to use the card definition."); 130 MODULE_PARM_DESC(no_overlay, "allow override overlay default (0 disables, 1 enables) [some VIA/SIS chipsets are known to have problem with overlay]"); 131 132 133 /* I2C addresses list */ 134 #define I2C_ADDR_TDA7432 0x8a 135 #define I2C_ADDR_MSP3400 0x80 136 #define I2C_ADDR_MSP3400_ALT 0x88 137 138 139 /* ----------------------------------------------------------------------- */ 140 /* list of card IDs for bt878+ cards */ 141 142 static struct CARD { 143 unsigned id; 144 int cardnr; 145 char *name; 146 } cards[] = { 147 { 0x13eb0070, BTTV_BOARD_HAUPPAUGE878, "Hauppauge WinTV" }, 148 { 0x39000070, BTTV_BOARD_HAUPPAUGE878, "Hauppauge WinTV-D" }, 149 { 0x45000070, BTTV_BOARD_HAUPPAUGEPVR, "Hauppauge WinTV/PVR" }, 150 { 0xff000070, BTTV_BOARD_OSPREY1x0, "Osprey-100" }, 151 { 0xff010070, BTTV_BOARD_OSPREY2x0_SVID,"Osprey-200" }, 152 { 0xff020070, BTTV_BOARD_OSPREY500, "Osprey-500" }, 153 { 0xff030070, BTTV_BOARD_OSPREY2000, "Osprey-2000" }, 154 { 0xff040070, BTTV_BOARD_OSPREY540, "Osprey-540" }, 155 { 0xff070070, BTTV_BOARD_OSPREY440, "Osprey-440" }, 156 157 { 0x00011002, BTTV_BOARD_ATI_TVWONDER, "ATI TV Wonder" }, 158 { 0x00031002, BTTV_BOARD_ATI_TVWONDERVE,"ATI TV Wonder/VE" }, 159 160 { 0x6606107d, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" }, 161 { 0x6607107d, BTTV_BOARD_WINFASTVC100, "Leadtek WinFast VC 100" }, 162 { 0x6609107d, BTTV_BOARD_WINFAST2000, "Leadtek TV 2000 XP" }, 163 { 0x263610b4, BTTV_BOARD_STB2, "STB TV PCI FM, Gateway P/N 6000704" }, 164 { 0x264510b4, BTTV_BOARD_STB2, "STB TV PCI FM, Gateway P/N 6000704" }, 165 { 0x402010fc, BTTV_BOARD_GVBCTV3PCI, "I-O Data Co. GV-BCTV3/PCI" }, 166 { 0x405010fc, BTTV_BOARD_GVBCTV4PCI, "I-O Data Co. GV-BCTV4/PCI" }, 167 { 0x407010fc, BTTV_BOARD_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" }, 168 { 0xd01810fc, BTTV_BOARD_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" }, 169 170 { 0x001211bd, BTTV_BOARD_PINNACLE, "Pinnacle PCTV" }, 171 /* some cards ship with byteswapped IDs ... */ 172 { 0x1200bd11, BTTV_BOARD_PINNACLE, "Pinnacle PCTV [bswap]" }, 173 { 0xff00bd11, BTTV_BOARD_PINNACLE, "Pinnacle PCTV [bswap]" }, 174 /* this seems to happen as well ... */ 175 { 0xff1211bd, BTTV_BOARD_PINNACLE, "Pinnacle PCTV" }, 176 177 { 0x3000121a, BTTV_BOARD_VOODOOTV_200, "3Dfx VoodooTV 200" }, 178 { 0x263710b4, BTTV_BOARD_VOODOOTV_FM, "3Dfx VoodooTV FM" }, 179 { 0x3060121a, BTTV_BOARD_STB2, "3Dfx VoodooTV 100/ STB OEM" }, 180 181 { 0x3000144f, BTTV_BOARD_MAGICTVIEW063, "(Askey Magic/others) TView99 CPH06x" }, 182 { 0xa005144f, BTTV_BOARD_MAGICTVIEW063, "CPH06X TView99-Card" }, 183 { 0x3002144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH05x" }, 184 { 0x3005144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH061/06L (T1/LC)" }, 185 { 0x5000144f, BTTV_BOARD_MAGICTVIEW061, "Askey CPH050" }, 186 { 0x300014ff, BTTV_BOARD_MAGICTVIEW061, "TView 99 (CPH061)" }, 187 { 0x300214ff, BTTV_BOARD_PHOEBE_TVMAS, "Phoebe TV Master (CPH060)" }, 188 189 { 0x00011461, BTTV_BOARD_AVPHONE98, "AVerMedia TVPhone98" }, 190 { 0x00021461, BTTV_BOARD_AVERMEDIA98, "AVermedia TVCapture 98" }, 191 { 0x00031461, BTTV_BOARD_AVPHONE98, "AVerMedia TVPhone98" }, 192 { 0x00041461, BTTV_BOARD_AVERMEDIA98, "AVerMedia TVCapture 98" }, 193 { 0x03001461, BTTV_BOARD_AVERMEDIA98, "VDOMATE TV TUNER CARD" }, 194 195 { 0x1117153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Philips PAL B/G)" }, 196 { 0x1118153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Temic PAL B/G)" }, 197 { 0x1119153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Philips PAL I)" }, 198 { 0x111a153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Temic PAL I)" }, 199 200 { 0x1123153b, BTTV_BOARD_TERRATVRADIO, "Terratec TV Radio+" }, 201 { 0x1127153b, BTTV_BOARD_TERRATV, "Terratec TV+ (V1.05)" }, 202 /* clashes with FlyVideo 203 *{ 0x18521852, BTTV_BOARD_TERRATV, "Terratec TV+ (V1.10)" }, */ 204 { 0x1134153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (LR102)" }, 205 { 0x1135153b, BTTV_BOARD_TERRATVALUER, "Terratec TValue Radio" }, /* LR102 */ 206 { 0x5018153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue" }, /* ?? */ 207 { 0xff3b153b, BTTV_BOARD_TERRATVALUER, "Terratec TValue Radio" }, /* ?? */ 208 209 { 0x400015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" }, 210 { 0x400a15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" }, 211 { 0x400d15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" }, 212 { 0x401015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" }, 213 { 0x401615b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" }, 214 215 { 0x1430aa00, BTTV_BOARD_PV143, "Provideo PV143A" }, 216 { 0x1431aa00, BTTV_BOARD_PV143, "Provideo PV143B" }, 217 { 0x1432aa00, BTTV_BOARD_PV143, "Provideo PV143C" }, 218 { 0x1433aa00, BTTV_BOARD_PV143, "Provideo PV143D" }, 219 { 0x1433aa03, BTTV_BOARD_PV143, "Security Eyes" }, 220 221 { 0x1460aa00, BTTV_BOARD_PV150, "Provideo PV150A-1" }, 222 { 0x1461aa01, BTTV_BOARD_PV150, "Provideo PV150A-2" }, 223 { 0x1462aa02, BTTV_BOARD_PV150, "Provideo PV150A-3" }, 224 { 0x1463aa03, BTTV_BOARD_PV150, "Provideo PV150A-4" }, 225 226 { 0x1464aa04, BTTV_BOARD_PV150, "Provideo PV150B-1" }, 227 { 0x1465aa05, BTTV_BOARD_PV150, "Provideo PV150B-2" }, 228 { 0x1466aa06, BTTV_BOARD_PV150, "Provideo PV150B-3" }, 229 { 0x1467aa07, BTTV_BOARD_PV150, "Provideo PV150B-4" }, 230 231 { 0xa132ff00, BTTV_BOARD_IVC100, "IVC-100" }, 232 { 0xa1550000, BTTV_BOARD_IVC200, "IVC-200" }, 233 { 0xa1550001, BTTV_BOARD_IVC200, "IVC-200" }, 234 { 0xa1550002, BTTV_BOARD_IVC200, "IVC-200" }, 235 { 0xa1550003, BTTV_BOARD_IVC200, "IVC-200" }, 236 { 0xa1550100, BTTV_BOARD_IVC200, "IVC-200G" }, 237 { 0xa1550101, BTTV_BOARD_IVC200, "IVC-200G" }, 238 { 0xa1550102, BTTV_BOARD_IVC200, "IVC-200G" }, 239 { 0xa1550103, BTTV_BOARD_IVC200, "IVC-200G" }, 240 { 0xa1550800, BTTV_BOARD_IVC200, "IVC-200" }, 241 { 0xa1550801, BTTV_BOARD_IVC200, "IVC-200" }, 242 { 0xa1550802, BTTV_BOARD_IVC200, "IVC-200" }, 243 { 0xa1550803, BTTV_BOARD_IVC200, "IVC-200" }, 244 { 0xa182ff00, BTTV_BOARD_IVC120, "IVC-120G" }, 245 { 0xa182ff01, BTTV_BOARD_IVC120, "IVC-120G" }, 246 { 0xa182ff02, BTTV_BOARD_IVC120, "IVC-120G" }, 247 { 0xa182ff03, BTTV_BOARD_IVC120, "IVC-120G" }, 248 { 0xa182ff04, BTTV_BOARD_IVC120, "IVC-120G" }, 249 { 0xa182ff05, BTTV_BOARD_IVC120, "IVC-120G" }, 250 { 0xa182ff06, BTTV_BOARD_IVC120, "IVC-120G" }, 251 { 0xa182ff07, BTTV_BOARD_IVC120, "IVC-120G" }, 252 { 0xa182ff08, BTTV_BOARD_IVC120, "IVC-120G" }, 253 { 0xa182ff09, BTTV_BOARD_IVC120, "IVC-120G" }, 254 { 0xa182ff0a, BTTV_BOARD_IVC120, "IVC-120G" }, 255 { 0xa182ff0b, BTTV_BOARD_IVC120, "IVC-120G" }, 256 { 0xa182ff0c, BTTV_BOARD_IVC120, "IVC-120G" }, 257 { 0xa182ff0d, BTTV_BOARD_IVC120, "IVC-120G" }, 258 { 0xa182ff0e, BTTV_BOARD_IVC120, "IVC-120G" }, 259 { 0xa182ff0f, BTTV_BOARD_IVC120, "IVC-120G" }, 260 { 0xf0500000, BTTV_BOARD_IVCE8784, "IVCE-8784" }, 261 { 0xf0500001, BTTV_BOARD_IVCE8784, "IVCE-8784" }, 262 { 0xf0500002, BTTV_BOARD_IVCE8784, "IVCE-8784" }, 263 { 0xf0500003, BTTV_BOARD_IVCE8784, "IVCE-8784" }, 264 265 { 0x41424344, BTTV_BOARD_GRANDTEC, "GrandTec Multi Capture" }, 266 { 0x01020304, BTTV_BOARD_XGUARD, "Grandtec Grand X-Guard" }, 267 268 { 0x18501851, BTTV_BOARD_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" }, 269 { 0xa0501851, BTTV_BOARD_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" }, 270 { 0x18511851, BTTV_BOARD_FLYVIDEO98EZ, "FlyVideo 98EZ (LR51)/ CyberMail AV" }, 271 { 0x18521852, BTTV_BOARD_TYPHOON_TVIEW, "FlyVideo 98FM (LR50)/ Typhoon TView TV/FM Tuner" }, 272 { 0x41a0a051, BTTV_BOARD_FLYVIDEO_98FM, "Lifeview FlyVideo 98 LR50 Rev Q" }, 273 { 0x18501f7f, BTTV_BOARD_FLYVIDEO_98, "Lifeview Flyvideo 98" }, 274 275 { 0x010115cb, BTTV_BOARD_GMV1, "AG GMV1" }, 276 { 0x010114c7, BTTV_BOARD_MODTEC_205, "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV" }, 277 278 { 0x10b42636, BTTV_BOARD_HAUPPAUGE878, "STB ???" }, 279 { 0x217d6606, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" }, 280 { 0xfff6f6ff, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" }, 281 { 0x03116000, BTTV_BOARD_SENSORAY311_611, "Sensoray 311" }, 282 { 0x06116000, BTTV_BOARD_SENSORAY311_611, "Sensoray 611" }, 283 { 0x00790e11, BTTV_BOARD_WINDVR, "Canopus WinDVR PCI" }, 284 { 0xa0fca1a0, BTTV_BOARD_ZOLTRIX, "Face to Face Tvmax" }, 285 { 0x82b2aa6a, BTTV_BOARD_SIMUS_GVC1100, "SIMUS GVC1100" }, 286 { 0x146caa0c, BTTV_BOARD_PV951, "ituner spectra8" }, 287 { 0x200a1295, BTTV_BOARD_PXC200, "ImageNation PXC200A" }, 288 289 { 0x40111554, BTTV_BOARD_PV_BT878P_9B, "Prolink Pixelview PV-BT" }, 290 { 0x17de0a01, BTTV_BOARD_KWORLD, "Mecer TV/FM/Video Tuner" }, 291 292 { 0x01051805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #1" }, 293 { 0x01061805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #2" }, 294 { 0x01071805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #3" }, 295 { 0x01081805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #4" }, 296 297 { 0x15409511, BTTV_BOARD_ACORP_Y878F, "Acorp Y878F" }, 298 299 { 0x53534149, BTTV_BOARD_SSAI_SECURITY, "SSAI Security Video Interface" }, 300 { 0x5353414a, BTTV_BOARD_SSAI_ULTRASOUND, "SSAI Ultrasound Video Interface" }, 301 302 /* likely broken, vendor id doesn't match the other magic views ... 303 * { 0xa0fca04f, BTTV_BOARD_MAGICTVIEW063, "Guillemot Maxi TV Video 3" }, */ 304 305 /* Duplicate PCI ID, reconfigure for this board during the eeprom read. 306 * { 0x13eb0070, BTTV_BOARD_HAUPPAUGE_IMPACTVCB, "Hauppauge ImpactVCB" }, */ 307 308 { 0x109e036e, BTTV_BOARD_CONCEPTRONIC_CTVFMI2, "Conceptronic CTVFMi v2"}, 309 310 /* DVB cards (using pci function .1 for mpeg data xfer) */ 311 { 0x001c11bd, BTTV_BOARD_PINNACLESAT, "Pinnacle PCTV Sat" }, 312 { 0x01010071, BTTV_BOARD_NEBULA_DIGITV, "Nebula Electronics DigiTV" }, 313 { 0x20007063, BTTV_BOARD_PC_HDTV, "pcHDTV HD-2000 TV"}, 314 { 0x002611bd, BTTV_BOARD_TWINHAN_DST, "Pinnacle PCTV SAT CI" }, 315 { 0x00011822, BTTV_BOARD_TWINHAN_DST, "Twinhan VisionPlus DVB" }, 316 { 0xfc00270f, BTTV_BOARD_TWINHAN_DST, "ChainTech digitop DST-1000 DVB-S" }, 317 { 0x07711461, BTTV_BOARD_AVDVBT_771, "AVermedia AverTV DVB-T 771" }, 318 { 0x07611461, BTTV_BOARD_AVDVBT_761, "AverMedia AverTV DVB-T 761" }, 319 { 0xdb1018ac, BTTV_BOARD_DVICO_DVBT_LITE, "DViCO FusionHDTV DVB-T Lite" }, 320 { 0xdb1118ac, BTTV_BOARD_DVICO_DVBT_LITE, "Ultraview DVB-T Lite" }, 321 { 0xd50018ac, BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE, "DViCO FusionHDTV 5 Lite" }, 322 { 0x00261822, BTTV_BOARD_TWINHAN_DST, "DNTV Live! Mini "}, 323 { 0xd200dbc0, BTTV_BOARD_DVICO_FUSIONHDTV_2, "DViCO FusionHDTV 2" }, 324 { 0x763c008a, BTTV_BOARD_GEOVISION_GV600, "GeoVision GV-600" }, 325 { 0x18011000, BTTV_BOARD_ENLTV_FM_2, "Encore ENL TV-FM-2" }, 326 { 0x763d800a, BTTV_BOARD_GEOVISION_GV800S, "GeoVision GV-800(S) (master)" }, 327 { 0x763d800b, BTTV_BOARD_GEOVISION_GV800S_SL, "GeoVision GV-800(S) (slave)" }, 328 { 0x763d800c, BTTV_BOARD_GEOVISION_GV800S_SL, "GeoVision GV-800(S) (slave)" }, 329 { 0x763d800d, BTTV_BOARD_GEOVISION_GV800S_SL, "GeoVision GV-800(S) (slave)" }, 330 331 { 0x15401830, BTTV_BOARD_PV183, "Provideo PV183-1" }, 332 { 0x15401831, BTTV_BOARD_PV183, "Provideo PV183-2" }, 333 { 0x15401832, BTTV_BOARD_PV183, "Provideo PV183-3" }, 334 { 0x15401833, BTTV_BOARD_PV183, "Provideo PV183-4" }, 335 { 0x15401834, BTTV_BOARD_PV183, "Provideo PV183-5" }, 336 { 0x15401835, BTTV_BOARD_PV183, "Provideo PV183-6" }, 337 { 0x15401836, BTTV_BOARD_PV183, "Provideo PV183-7" }, 338 { 0x15401837, BTTV_BOARD_PV183, "Provideo PV183-8" }, 339 { 0x3116f200, BTTV_BOARD_TVT_TD3116, "Tongwei Video Technology TD-3116" }, 340 { 0x02280279, BTTV_BOARD_APOSONIC_WDVR, "Aposonic W-DVR" }, 341 { 0, -1, NULL } 342 }; 343 344 /* ----------------------------------------------------------------------- */ 345 /* array with description for bt848 / bt878 tv/grabber cards */ 346 347 struct tvcard bttv_tvcards[] = { 348 /* ---- card 0x00 ---------------------------------- */ 349 [BTTV_BOARD_UNKNOWN] = { 350 .name = " *** UNKNOWN/GENERIC *** ", 351 .video_inputs = 4, 352 .svhs = 2, 353 .muxsel = MUXSEL(2, 3, 1, 0), 354 .tuner_type = UNSET, 355 .tuner_addr = ADDR_UNSET, 356 }, 357 [BTTV_BOARD_MIRO] = { 358 .name = "MIRO PCTV", 359 .video_inputs = 4, 360 /* .audio_inputs= 1, */ 361 .svhs = 2, 362 .gpiomask = 15, 363 .muxsel = MUXSEL(2, 3, 1, 1), 364 .gpiomux = { 2, 0, 0, 0 }, 365 .gpiomute = 10, 366 .tuner_type = UNSET, 367 .tuner_addr = ADDR_UNSET, 368 }, 369 [BTTV_BOARD_HAUPPAUGE] = { 370 .name = "Hauppauge (bt848)", 371 .video_inputs = 4, 372 /* .audio_inputs= 1, */ 373 .svhs = 2, 374 .gpiomask = 7, 375 .muxsel = MUXSEL(2, 3, 1, 1), 376 .gpiomux = { 0, 1, 2, 3 }, 377 .gpiomute = 4, 378 .tuner_type = UNSET, 379 .tuner_addr = ADDR_UNSET, 380 }, 381 [BTTV_BOARD_STB] = { 382 .name = "STB, Gateway P/N 6000699 (bt848)", 383 .video_inputs = 3, 384 /* .audio_inputs= 1, */ 385 .svhs = 2, 386 .gpiomask = 7, 387 .muxsel = MUXSEL(2, 3, 1, 1), 388 .gpiomux = { 4, 0, 2, 3 }, 389 .gpiomute = 1, 390 .no_msp34xx = 1, 391 .tuner_type = TUNER_PHILIPS_NTSC, 392 .tuner_addr = ADDR_UNSET, 393 .pll = PLL_28, 394 .has_radio = 1, 395 }, 396 397 /* ---- card 0x04 ---------------------------------- */ 398 [BTTV_BOARD_INTEL] = { 399 .name = "Intel Create and Share PCI/ Smart Video Recorder III", 400 .video_inputs = 4, 401 /* .audio_inputs= 0, */ 402 .svhs = 2, 403 .gpiomask = 0, 404 .muxsel = MUXSEL(2, 3, 1, 1), 405 .gpiomux = { 0 }, 406 .tuner_type = TUNER_ABSENT, 407 .tuner_addr = ADDR_UNSET, 408 }, 409 [BTTV_BOARD_DIAMOND] = { 410 .name = "Diamond DTV2000", 411 .video_inputs = 4, 412 /* .audio_inputs= 1, */ 413 .svhs = 2, 414 .gpiomask = 3, 415 .muxsel = MUXSEL(2, 3, 1, 0), 416 .gpiomux = { 0, 1, 0, 1 }, 417 .gpiomute = 3, 418 .tuner_type = UNSET, 419 .tuner_addr = ADDR_UNSET, 420 }, 421 [BTTV_BOARD_AVERMEDIA] = { 422 .name = "AVerMedia TVPhone", 423 .video_inputs = 3, 424 /* .audio_inputs= 1, */ 425 .svhs = 3, 426 .muxsel = MUXSEL(2, 3, 1, 1), 427 .gpiomask = 0x0f, 428 .gpiomux = { 0x0c, 0x04, 0x08, 0x04 }, 429 /* 0x04 for some cards ?? */ 430 .tuner_type = UNSET, 431 .tuner_addr = ADDR_UNSET, 432 .audio_mode_gpio= avermedia_tvphone_audio, 433 .has_remote = 1, 434 }, 435 [BTTV_BOARD_MATRIX_VISION] = { 436 .name = "MATRIX-Vision MV-Delta", 437 .video_inputs = 5, 438 /* .audio_inputs= 1, */ 439 .svhs = 3, 440 .gpiomask = 0, 441 .muxsel = MUXSEL(2, 3, 1, 0, 0), 442 .gpiomux = { 0 }, 443 .tuner_type = TUNER_ABSENT, 444 .tuner_addr = ADDR_UNSET, 445 }, 446 447 /* ---- card 0x08 ---------------------------------- */ 448 [BTTV_BOARD_FLYVIDEO] = { 449 .name = "Lifeview FlyVideo II (Bt848) LR26 / MAXI TV Video PCI2 LR26", 450 .video_inputs = 4, 451 /* .audio_inputs= 1, */ 452 .svhs = 2, 453 .gpiomask = 0xc00, 454 .muxsel = MUXSEL(2, 3, 1, 1), 455 .gpiomux = { 0, 0xc00, 0x800, 0x400 }, 456 .gpiomute = 0xc00, 457 .pll = PLL_28, 458 .tuner_type = UNSET, 459 .tuner_addr = ADDR_UNSET, 460 }, 461 [BTTV_BOARD_TURBOTV] = { 462 .name = "IMS/IXmicro TurboTV", 463 .video_inputs = 3, 464 /* .audio_inputs= 1, */ 465 .svhs = 2, 466 .gpiomask = 3, 467 .muxsel = MUXSEL(2, 3, 1, 1), 468 .gpiomux = { 1, 1, 2, 3 }, 469 .pll = PLL_28, 470 .tuner_type = TUNER_TEMIC_PAL, 471 .tuner_addr = ADDR_UNSET, 472 }, 473 [BTTV_BOARD_HAUPPAUGE878] = { 474 .name = "Hauppauge (bt878)", 475 .video_inputs = 4, 476 /* .audio_inputs= 1, */ 477 .svhs = 2, 478 .gpiomask = 0x0f, /* old: 7 */ 479 .muxsel = MUXSEL(2, 0, 1, 1), 480 .gpiomux = { 0, 1, 2, 3 }, 481 .gpiomute = 4, 482 .pll = PLL_28, 483 .tuner_type = UNSET, 484 .tuner_addr = ADDR_UNSET, 485 }, 486 [BTTV_BOARD_MIROPRO] = { 487 .name = "MIRO PCTV pro", 488 .video_inputs = 3, 489 /* .audio_inputs= 1, */ 490 .svhs = 2, 491 .gpiomask = 0x3014f, 492 .muxsel = MUXSEL(2, 3, 1, 1), 493 .gpiomux = { 0x20001,0x10001, 0, 0 }, 494 .gpiomute = 10, 495 .tuner_type = UNSET, 496 .tuner_addr = ADDR_UNSET, 497 }, 498 499 /* ---- card 0x0c ---------------------------------- */ 500 [BTTV_BOARD_ADSTECH_TV] = { 501 .name = "ADS Technologies Channel Surfer TV (bt848)", 502 .video_inputs = 3, 503 /* .audio_inputs= 1, */ 504 .svhs = 2, 505 .gpiomask = 15, 506 .muxsel = MUXSEL(2, 3, 1, 1), 507 .gpiomux = { 13, 14, 11, 7 }, 508 .tuner_type = UNSET, 509 .tuner_addr = ADDR_UNSET, 510 }, 511 [BTTV_BOARD_AVERMEDIA98] = { 512 .name = "AVerMedia TVCapture 98", 513 .video_inputs = 3, 514 /* .audio_inputs= 4, */ 515 .svhs = 2, 516 .gpiomask = 15, 517 .muxsel = MUXSEL(2, 3, 1, 1), 518 .gpiomux = { 13, 14, 11, 7 }, 519 .msp34xx_alt = 1, 520 .pll = PLL_28, 521 .tuner_type = TUNER_PHILIPS_PAL, 522 .tuner_addr = ADDR_UNSET, 523 .audio_mode_gpio= avermedia_tv_stereo_audio, 524 .no_gpioirq = 1, 525 }, 526 [BTTV_BOARD_VHX] = { 527 .name = "Aimslab Video Highway Xtreme (VHX)", 528 .video_inputs = 3, 529 /* .audio_inputs= 1, */ 530 .svhs = 2, 531 .gpiomask = 7, 532 .muxsel = MUXSEL(2, 3, 1, 1), 533 .gpiomux = { 0, 2, 1, 3 }, /* old: {0, 1, 2, 3, 4} */ 534 .gpiomute = 4, 535 .pll = PLL_28, 536 .tuner_type = UNSET, 537 .tuner_addr = ADDR_UNSET, 538 }, 539 [BTTV_BOARD_ZOLTRIX] = { 540 .name = "Zoltrix TV-Max", 541 .video_inputs = 3, 542 /* .audio_inputs= 1, */ 543 .svhs = 2, 544 .gpiomask = 15, 545 .muxsel = MUXSEL(2, 3, 1, 1), 546 .gpiomux = { 0, 0, 1, 0 }, 547 .gpiomute = 10, 548 .tuner_type = UNSET, 549 .tuner_addr = ADDR_UNSET, 550 }, 551 552 /* ---- card 0x10 ---------------------------------- */ 553 [BTTV_BOARD_PIXVIEWPLAYTV] = { 554 .name = "Prolink Pixelview PlayTV (bt878)", 555 .video_inputs = 3, 556 /* .audio_inputs= 1, */ 557 .svhs = 2, 558 .gpiomask = 0x01fe00, 559 .muxsel = MUXSEL(2, 3, 1, 1), 560 /* 2003-10-20 by "Anton A. Arapov" <arapov@mail.ru> */ 561 .gpiomux = { 0x001e00, 0, 0x018000, 0x014000 }, 562 .gpiomute = 0x002000, 563 .pll = PLL_28, 564 .tuner_type = UNSET, 565 .tuner_addr = ADDR_UNSET, 566 }, 567 [BTTV_BOARD_WINVIEW_601] = { 568 .name = "Leadtek WinView 601", 569 .video_inputs = 3, 570 /* .audio_inputs= 1, */ 571 .svhs = 2, 572 .gpiomask = 0x8300f8, 573 .muxsel = MUXSEL(2, 3, 1, 1, 0), 574 .gpiomux = { 0x4fa007,0xcfa007,0xcfa007,0xcfa007 }, 575 .gpiomute = 0xcfa007, 576 .tuner_type = UNSET, 577 .tuner_addr = ADDR_UNSET, 578 .volume_gpio = winview_volume, 579 .has_radio = 1, 580 }, 581 [BTTV_BOARD_AVEC_INTERCAP] = { 582 .name = "AVEC Intercapture", 583 .video_inputs = 3, 584 /* .audio_inputs= 2, */ 585 .svhs = 2, 586 .gpiomask = 0, 587 .muxsel = MUXSEL(2, 3, 1, 1), 588 .gpiomux = { 1, 0, 0, 0 }, 589 .tuner_type = UNSET, 590 .tuner_addr = ADDR_UNSET, 591 }, 592 [BTTV_BOARD_LIFE_FLYKIT] = { 593 .name = "Lifeview FlyVideo II EZ /FlyKit LR38 Bt848 (capture only)", 594 .video_inputs = 4, 595 /* .audio_inputs= 1, */ 596 .svhs = NO_SVHS, 597 .gpiomask = 0x8dff00, 598 .muxsel = MUXSEL(2, 3, 1, 1), 599 .gpiomux = { 0 }, 600 .no_msp34xx = 1, 601 .tuner_type = TUNER_ABSENT, 602 .tuner_addr = ADDR_UNSET, 603 }, 604 605 /* ---- card 0x14 ---------------------------------- */ 606 [BTTV_BOARD_CEI_RAFFLES] = { 607 .name = "CEI Raffles Card", 608 .video_inputs = 3, 609 /* .audio_inputs= 3, */ 610 .svhs = 2, 611 .muxsel = MUXSEL(2, 3, 1, 1), 612 .tuner_type = UNSET, 613 .tuner_addr = ADDR_UNSET, 614 }, 615 [BTTV_BOARD_CONFERENCETV] = { 616 .name = "Lifeview FlyVideo 98/ Lucky Star Image World ConferenceTV LR50", 617 .video_inputs = 4, 618 /* .audio_inputs= 2, tuner, line in */ 619 .svhs = 2, 620 .gpiomask = 0x1800, 621 .muxsel = MUXSEL(2, 3, 1, 1), 622 .gpiomux = { 0, 0x800, 0x1000, 0x1000 }, 623 .gpiomute = 0x1800, 624 .pll = PLL_28, 625 .tuner_type = TUNER_PHILIPS_PAL_I, 626 .tuner_addr = ADDR_UNSET, 627 }, 628 [BTTV_BOARD_PHOEBE_TVMAS] = { 629 .name = "Askey CPH050/ Phoebe Tv Master + FM", 630 .video_inputs = 3, 631 /* .audio_inputs= 1, */ 632 .svhs = 2, 633 .gpiomask = 0xc00, 634 .muxsel = MUXSEL(2, 3, 1, 1), 635 .gpiomux = { 0, 1, 0x800, 0x400 }, 636 .gpiomute = 0xc00, 637 .pll = PLL_28, 638 .tuner_type = UNSET, 639 .tuner_addr = ADDR_UNSET, 640 }, 641 [BTTV_BOARD_MODTEC_205] = { 642 .name = "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV, bt878", 643 .video_inputs = 3, 644 /* .audio_inputs= 1, */ 645 .svhs = NO_SVHS, 646 .has_dig_in = 1, 647 .gpiomask = 7, 648 .muxsel = MUXSEL(2, 3, 0), /* input 2 is digital */ 649 /* .digital_mode= DIGITAL_MODE_CAMERA, */ 650 .gpiomux = { 0, 0, 0, 0 }, 651 .no_msp34xx = 1, 652 .pll = PLL_28, 653 .tuner_type = TUNER_ALPS_TSBB5_PAL_I, 654 .tuner_addr = ADDR_UNSET, 655 }, 656 657 /* ---- card 0x18 ---------------------------------- */ 658 [BTTV_BOARD_MAGICTVIEW061] = { 659 .name = "Askey CPH05X/06X (bt878) [many vendors]", 660 .video_inputs = 3, 661 /* .audio_inputs= 1, */ 662 .svhs = 2, 663 .gpiomask = 0xe00, 664 .muxsel = MUXSEL(2, 3, 1, 1), 665 .gpiomux = {0x400, 0x400, 0x400, 0x400 }, 666 .gpiomute = 0xc00, 667 .pll = PLL_28, 668 .tuner_type = UNSET, 669 .tuner_addr = ADDR_UNSET, 670 .has_remote = 1, 671 .has_radio = 1, /* not every card has radio */ 672 }, 673 [BTTV_BOARD_VOBIS_BOOSTAR] = { 674 .name = "Terratec TerraTV+ Version 1.0 (Bt848)/ Terra TValue Version 1.0/ Vobis TV-Boostar", 675 .video_inputs = 3, 676 /* .audio_inputs= 1, */ 677 .svhs = 2, 678 .gpiomask = 0x1f0fff, 679 .muxsel = MUXSEL(2, 3, 1, 1), 680 .gpiomux = { 0x20000, 0x30000, 0x10000, 0 }, 681 .gpiomute = 0x40000, 682 .tuner_type = TUNER_PHILIPS_PAL, 683 .tuner_addr = ADDR_UNSET, 684 .audio_mode_gpio= terratv_audio, 685 }, 686 [BTTV_BOARD_HAUPPAUG_WCAM] = { 687 .name = "Hauppauge WinCam newer (bt878)", 688 .video_inputs = 4, 689 /* .audio_inputs= 1, */ 690 .svhs = 3, 691 .gpiomask = 7, 692 .muxsel = MUXSEL(2, 0, 1, 1), 693 .gpiomux = { 0, 1, 2, 3 }, 694 .gpiomute = 4, 695 .tuner_type = UNSET, 696 .tuner_addr = ADDR_UNSET, 697 }, 698 [BTTV_BOARD_MAXI] = { 699 .name = "Lifeview FlyVideo 98/ MAXI TV Video PCI2 LR50", 700 .video_inputs = 4, 701 /* .audio_inputs= 2, */ 702 .svhs = 2, 703 .gpiomask = 0x1800, 704 .muxsel = MUXSEL(2, 3, 1, 1), 705 .gpiomux = { 0, 0x800, 0x1000, 0x1000 }, 706 .gpiomute = 0x1800, 707 .pll = PLL_28, 708 .tuner_type = TUNER_PHILIPS_SECAM, 709 .tuner_addr = ADDR_UNSET, 710 }, 711 712 /* ---- card 0x1c ---------------------------------- */ 713 [BTTV_BOARD_TERRATV] = { 714 .name = "Terratec TerraTV+ Version 1.1 (bt878)", 715 .video_inputs = 3, 716 /* .audio_inputs= 1, */ 717 .svhs = 2, 718 .gpiomask = 0x1f0fff, 719 .muxsel = MUXSEL(2, 3, 1, 1), 720 .gpiomux = { 0x20000, 0x30000, 0x10000, 0x00000 }, 721 .gpiomute = 0x40000, 722 .tuner_type = TUNER_PHILIPS_PAL, 723 .tuner_addr = ADDR_UNSET, 724 .audio_mode_gpio= terratv_audio, 725 /* GPIO wiring: 726 External 20 pin connector (for Active Radio Upgrade board) 727 gpio00: i2c-sda 728 gpio01: i2c-scl 729 gpio02: om5610-data 730 gpio03: om5610-clk 731 gpio04: om5610-wre 732 gpio05: om5610-stereo 733 gpio06: rds6588-davn 734 gpio07: Pin 7 n.c. 735 gpio08: nIOW 736 gpio09+10: nIOR, nSEL ?? (bt878) 737 gpio09: nIOR (bt848) 738 gpio10: nSEL (bt848) 739 Sound Routing: 740 gpio16: u2-A0 (1st 4052bt) 741 gpio17: u2-A1 742 gpio18: u2-nEN 743 gpio19: u4-A0 (2nd 4052) 744 gpio20: u4-A1 745 u4-nEN - GND 746 Btspy: 747 00000 : Cdrom (internal audio input) 748 10000 : ext. Video audio input 749 20000 : TV Mono 750 a0000 : TV Mono/2 751 1a0000 : TV Stereo 752 30000 : Radio 753 40000 : Mute 754 */ 755 756 }, 757 [BTTV_BOARD_PXC200] = { 758 /* Jannik Fritsch <jannik@techfak.uni-bielefeld.de> */ 759 .name = "Imagenation PXC200", 760 .video_inputs = 5, 761 /* .audio_inputs= 1, */ 762 .svhs = 1, /* was: 4 */ 763 .gpiomask = 0, 764 .muxsel = MUXSEL(2, 3, 1, 0, 0), 765 .gpiomux = { 0 }, 766 .tuner_type = TUNER_ABSENT, 767 .tuner_addr = ADDR_UNSET, 768 .muxsel_hook = PXC200_muxsel, 769 770 }, 771 [BTTV_BOARD_FLYVIDEO_98] = { 772 .name = "Lifeview FlyVideo 98 LR50", 773 .video_inputs = 4, 774 /* .audio_inputs= 1, */ 775 .svhs = 2, 776 .gpiomask = 0x1800, /* 0x8dfe00 */ 777 .muxsel = MUXSEL(2, 3, 1, 1), 778 .gpiomux = { 0, 0x0800, 0x1000, 0x1000 }, 779 .gpiomute = 0x1800, 780 .pll = PLL_28, 781 .tuner_type = UNSET, 782 .tuner_addr = ADDR_UNSET, 783 }, 784 [BTTV_BOARD_IPROTV] = { 785 .name = "Formac iProTV, Formac ProTV I (bt848)", 786 .video_inputs = 4, 787 /* .audio_inputs= 1, */ 788 .svhs = 3, 789 .gpiomask = 1, 790 .muxsel = MUXSEL(2, 3, 1, 1), 791 .gpiomux = { 1, 0, 0, 0 }, 792 .pll = PLL_28, 793 .tuner_type = TUNER_PHILIPS_PAL, 794 .tuner_addr = ADDR_UNSET, 795 }, 796 797 /* ---- card 0x20 ---------------------------------- */ 798 [BTTV_BOARD_INTEL_C_S_PCI] = { 799 .name = "Intel Create and Share PCI/ Smart Video Recorder III", 800 .video_inputs = 4, 801 /* .audio_inputs= 0, */ 802 .svhs = 2, 803 .gpiomask = 0, 804 .muxsel = MUXSEL(2, 3, 1, 1), 805 .gpiomux = { 0 }, 806 .tuner_type = TUNER_ABSENT, 807 .tuner_addr = ADDR_UNSET, 808 }, 809 [BTTV_BOARD_TERRATVALUE] = { 810 .name = "Terratec TerraTValue Version Bt878", 811 .video_inputs = 3, 812 /* .audio_inputs= 1, */ 813 .svhs = 2, 814 .gpiomask = 0xffff00, 815 .muxsel = MUXSEL(2, 3, 1, 1), 816 .gpiomux = { 0x500, 0, 0x300, 0x900 }, 817 .gpiomute = 0x900, 818 .pll = PLL_28, 819 .tuner_type = TUNER_PHILIPS_PAL, 820 .tuner_addr = ADDR_UNSET, 821 }, 822 [BTTV_BOARD_WINFAST2000] = { 823 .name = "Leadtek WinFast 2000/ WinFast 2000 XP", 824 .video_inputs = 4, 825 /* .audio_inputs= 1, */ 826 .svhs = 2, 827 /* TV, CVid, SVid, CVid over SVid connector */ 828 .muxsel = MUXSEL(2, 3, 1, 1, 0), 829 /* Alexander Varakin <avarakin@hotmail.com> [stereo version] */ 830 .gpiomask = 0xb33000, 831 .gpiomux = { 0x122000,0x1000,0x0000,0x620000 }, 832 .gpiomute = 0x800000, 833 /* Audio Routing for "WinFast 2000 XP" (no tv stereo !) 834 gpio23 -- hef4052:nEnable (0x800000) 835 gpio12 -- hef4052:A1 836 gpio13 -- hef4052:A0 837 0x0000: external audio 838 0x1000: FM 839 0x2000: TV 840 0x3000: n.c. 841 Note: There exists another variant "Winfast 2000" with tv stereo !? 842 Note: eeprom only contains FF and pci subsystem id 107d:6606 843 */ 844 .pll = PLL_28, 845 .has_radio = 1, 846 .tuner_type = TUNER_PHILIPS_PAL, /* default for now, gpio reads BFFF06 for Pal bg+dk */ 847 .tuner_addr = ADDR_UNSET, 848 .audio_mode_gpio= winfast2000_audio, 849 .has_remote = 1, 850 }, 851 [BTTV_BOARD_CHRONOS_VS2] = { 852 .name = "Lifeview FlyVideo 98 LR50 / Chronos Video Shuttle II", 853 .video_inputs = 4, 854 /* .audio_inputs= 3, */ 855 .svhs = 2, 856 .gpiomask = 0x1800, 857 .muxsel = MUXSEL(2, 3, 1, 1), 858 .gpiomux = { 0, 0x800, 0x1000, 0x1000 }, 859 .gpiomute = 0x1800, 860 .pll = PLL_28, 861 .tuner_type = UNSET, 862 .tuner_addr = ADDR_UNSET, 863 }, 864 865 /* ---- card 0x24 ---------------------------------- */ 866 [BTTV_BOARD_TYPHOON_TVIEW] = { 867 .name = "Lifeview FlyVideo 98FM LR50 / Typhoon TView TV/FM Tuner", 868 .video_inputs = 4, 869 /* .audio_inputs= 3, */ 870 .svhs = 2, 871 .gpiomask = 0x1800, 872 .muxsel = MUXSEL(2, 3, 1, 1), 873 .gpiomux = { 0, 0x800, 0x1000, 0x1000 }, 874 .gpiomute = 0x1800, 875 .pll = PLL_28, 876 .tuner_type = UNSET, 877 .tuner_addr = ADDR_UNSET, 878 .has_radio = 1, 879 }, 880 [BTTV_BOARD_PXELVWPLTVPRO] = { 881 .name = "Prolink PixelView PlayTV pro", 882 .video_inputs = 3, 883 /* .audio_inputs= 1, */ 884 .svhs = 2, 885 .gpiomask = 0xff, 886 .muxsel = MUXSEL(2, 3, 1, 1), 887 .gpiomux = { 0x21, 0x20, 0x24, 0x2c }, 888 .gpiomute = 0x29, 889 .no_msp34xx = 1, 890 .pll = PLL_28, 891 .tuner_type = UNSET, 892 .tuner_addr = ADDR_UNSET, 893 }, 894 [BTTV_BOARD_MAGICTVIEW063] = { 895 .name = "Askey CPH06X TView99", 896 .video_inputs = 4, 897 /* .audio_inputs= 1, */ 898 .svhs = 2, 899 .gpiomask = 0x551e00, 900 .muxsel = MUXSEL(2, 3, 1, 0), 901 .gpiomux = { 0x551400, 0x551200, 0, 0 }, 902 .gpiomute = 0x551c00, 903 .pll = PLL_28, 904 .tuner_type = TUNER_PHILIPS_PAL_I, 905 .tuner_addr = ADDR_UNSET, 906 .has_remote = 1, 907 }, 908 [BTTV_BOARD_PINNACLE] = { 909 .name = "Pinnacle PCTV Studio/Rave", 910 .video_inputs = 3, 911 /* .audio_inputs= 1, */ 912 .svhs = 2, 913 .gpiomask = 0x03000F, 914 .muxsel = MUXSEL(2, 3, 1, 1), 915 .gpiomux = { 2, 0xd0001, 0, 0 }, 916 .gpiomute = 1, 917 .pll = PLL_28, 918 .tuner_type = UNSET, 919 .tuner_addr = ADDR_UNSET, 920 }, 921 922 /* ---- card 0x28 ---------------------------------- */ 923 [BTTV_BOARD_STB2] = { 924 .name = "STB TV PCI FM, Gateway P/N 6000704 (bt878), 3Dfx VoodooTV 100", 925 .video_inputs = 3, 926 /* .audio_inputs= 1, */ 927 .svhs = 2, 928 .gpiomask = 7, 929 .muxsel = MUXSEL(2, 3, 1, 1), 930 .gpiomux = { 4, 0, 2, 3 }, 931 .gpiomute = 1, 932 .no_msp34xx = 1, 933 .tuner_type = TUNER_PHILIPS_NTSC, 934 .tuner_addr = ADDR_UNSET, 935 .pll = PLL_28, 936 .has_radio = 1, 937 }, 938 [BTTV_BOARD_AVPHONE98] = { 939 .name = "AVerMedia TVPhone 98", 940 .video_inputs = 3, 941 /* .audio_inputs= 4, */ 942 .svhs = 2, 943 .gpiomask = 15, 944 .muxsel = MUXSEL(2, 3, 1, 1), 945 .gpiomux = { 13, 4, 11, 7 }, 946 .pll = PLL_28, 947 .tuner_type = UNSET, 948 .tuner_addr = ADDR_UNSET, 949 .has_radio = 1, 950 .audio_mode_gpio= avermedia_tvphone_audio, 951 }, 952 [BTTV_BOARD_PV951] = { 953 .name = "ProVideo PV951", /* pic16c54 */ 954 .video_inputs = 3, 955 /* .audio_inputs= 1, */ 956 .svhs = 2, 957 .gpiomask = 0, 958 .muxsel = MUXSEL(2, 3, 1, 1), 959 .gpiomux = { 0, 0, 0, 0}, 960 .no_msp34xx = 1, 961 .pll = PLL_28, 962 .tuner_type = TUNER_PHILIPS_PAL_I, 963 .tuner_addr = ADDR_UNSET, 964 }, 965 [BTTV_BOARD_ONAIR_TV] = { 966 .name = "Little OnAir TV", 967 .video_inputs = 3, 968 /* .audio_inputs= 1, */ 969 .svhs = 2, 970 .gpiomask = 0xe00b, 971 .muxsel = MUXSEL(2, 3, 1, 1), 972 .gpiomux = { 0xff9ff6, 0xff9ff6, 0xff1ff7, 0 }, 973 .gpiomute = 0xff3ffc, 974 .no_msp34xx = 1, 975 .tuner_type = UNSET, 976 .tuner_addr = ADDR_UNSET, 977 }, 978 979 /* ---- card 0x2c ---------------------------------- */ 980 [BTTV_BOARD_SIGMA_TVII_FM] = { 981 .name = "Sigma TVII-FM", 982 .video_inputs = 2, 983 /* .audio_inputs= 1, */ 984 .svhs = NO_SVHS, 985 .gpiomask = 3, 986 .muxsel = MUXSEL(2, 3, 1, 1), 987 .gpiomux = { 1, 1, 0, 2 }, 988 .gpiomute = 3, 989 .no_msp34xx = 1, 990 .pll = PLL_NONE, 991 .tuner_type = UNSET, 992 .tuner_addr = ADDR_UNSET, 993 }, 994 [BTTV_BOARD_MATRIX_VISION2] = { 995 .name = "MATRIX-Vision MV-Delta 2", 996 .video_inputs = 5, 997 /* .audio_inputs= 1, */ 998 .svhs = 3, 999 .gpiomask = 0, 1000 .muxsel = MUXSEL(2, 3, 1, 0, 0), 1001 .gpiomux = { 0 }, 1002 .no_msp34xx = 1, 1003 .pll = PLL_28, 1004 .tuner_type = TUNER_ABSENT, 1005 .tuner_addr = ADDR_UNSET, 1006 }, 1007 [BTTV_BOARD_ZOLTRIX_GENIE] = { 1008 .name = "Zoltrix Genie TV/FM", 1009 .video_inputs = 3, 1010 /* .audio_inputs= 1, */ 1011 .svhs = 2, 1012 .gpiomask = 0xbcf03f, 1013 .muxsel = MUXSEL(2, 3, 1, 1), 1014 .gpiomux = { 0xbc803f, 0xbc903f, 0xbcb03f, 0 }, 1015 .gpiomute = 0xbcb03f, 1016 .no_msp34xx = 1, 1017 .pll = PLL_28, 1018 .tuner_type = TUNER_TEMIC_4039FR5_NTSC, 1019 .tuner_addr = ADDR_UNSET, 1020 }, 1021 [BTTV_BOARD_TERRATVRADIO] = { 1022 .name = "Terratec TV/Radio+", 1023 .video_inputs = 3, 1024 /* .audio_inputs= 1, */ 1025 .svhs = 2, 1026 .gpiomask = 0x70000, 1027 .muxsel = MUXSEL(2, 3, 1, 1), 1028 .gpiomux = { 0x20000, 0x30000, 0x10000, 0 }, 1029 .gpiomute = 0x40000, 1030 .no_msp34xx = 1, 1031 .pll = PLL_35, 1032 .tuner_type = TUNER_PHILIPS_PAL_I, 1033 .tuner_addr = ADDR_UNSET, 1034 .has_radio = 1, 1035 }, 1036 1037 /* ---- card 0x30 ---------------------------------- */ 1038 [BTTV_BOARD_DYNALINK] = { 1039 .name = "Askey CPH03x/ Dynalink Magic TView", 1040 .video_inputs = 3, 1041 /* .audio_inputs= 1, */ 1042 .svhs = 2, 1043 .gpiomask = 15, 1044 .muxsel = MUXSEL(2, 3, 1, 1), 1045 .gpiomux = {2,0,0,0 }, 1046 .gpiomute = 1, 1047 .pll = PLL_28, 1048 .tuner_type = UNSET, 1049 .tuner_addr = ADDR_UNSET, 1050 }, 1051 [BTTV_BOARD_GVBCTV3PCI] = { 1052 .name = "IODATA GV-BCTV3/PCI", 1053 .video_inputs = 3, 1054 /* .audio_inputs= 1, */ 1055 .svhs = 2, 1056 .gpiomask = 0x010f00, 1057 .muxsel = MUXSEL(2, 3, 0, 0), 1058 .gpiomux = {0x10000, 0, 0x10000, 0 }, 1059 .no_msp34xx = 1, 1060 .pll = PLL_28, 1061 .tuner_type = TUNER_ALPS_TSHC6_NTSC, 1062 .tuner_addr = ADDR_UNSET, 1063 .audio_mode_gpio= gvbctv3pci_audio, 1064 }, 1065 [BTTV_BOARD_PXELVWPLTVPAK] = { 1066 .name = "Prolink PV-BT878P+4E / PixelView PlayTV PAK / Lenco MXTV-9578 CP", 1067 .video_inputs = 5, 1068 /* .audio_inputs= 1, */ 1069 .svhs = 3, 1070 .has_dig_in = 1, 1071 .gpiomask = 0xAA0000, 1072 .muxsel = MUXSEL(2, 3, 1, 1, 0), /* in 4 is digital */ 1073 /* .digital_mode= DIGITAL_MODE_CAMERA, */ 1074 .gpiomux = { 0x20000, 0, 0x80000, 0x80000 }, 1075 .gpiomute = 0xa8000, 1076 .no_msp34xx = 1, 1077 .pll = PLL_28, 1078 .tuner_type = TUNER_PHILIPS_PAL_I, 1079 .tuner_addr = ADDR_UNSET, 1080 .has_remote = 1, 1081 /* GPIO wiring: (different from Rev.4C !) 1082 GPIO17: U4.A0 (first hef4052bt) 1083 GPIO19: U4.A1 1084 GPIO20: U5.A1 (second hef4052bt) 1085 GPIO21: U4.nEN 1086 GPIO22: BT832 Reset Line 1087 GPIO23: A5,A0, U5,nEN 1088 Note: At i2c=0x8a is a Bt832 chip, which changes to 0x88 after being reset via GPIO22 1089 */ 1090 }, 1091 [BTTV_BOARD_EAGLE] = { 1092 .name = "Eagle Wireless Capricorn2 (bt878A)", 1093 .video_inputs = 4, 1094 /* .audio_inputs= 1, */ 1095 .svhs = 2, 1096 .gpiomask = 7, 1097 .muxsel = MUXSEL(2, 0, 1, 1), 1098 .gpiomux = { 0, 1, 2, 3 }, 1099 .gpiomute = 4, 1100 .pll = PLL_28, 1101 .tuner_type = UNSET /* TUNER_ALPS_TMDH2_NTSC */, 1102 .tuner_addr = ADDR_UNSET, 1103 }, 1104 1105 /* ---- card 0x34 ---------------------------------- */ 1106 [BTTV_BOARD_PINNACLEPRO] = { 1107 /* David Härdeman <david@2gen.com> */ 1108 .name = "Pinnacle PCTV Studio Pro", 1109 .video_inputs = 4, 1110 /* .audio_inputs= 1, */ 1111 .svhs = 3, 1112 .gpiomask = 0x03000F, 1113 .muxsel = MUXSEL(2, 3, 1, 1), 1114 .gpiomux = { 1, 0xd0001, 0, 0 }, 1115 .gpiomute = 10, 1116 /* sound path (5 sources): 1117 MUX1 (mask 0x03), Enable Pin 0x08 (0=enable, 1=disable) 1118 0= ext. Audio IN 1119 1= from MUX2 1120 2= Mono TV sound from Tuner 1121 3= not connected 1122 MUX2 (mask 0x30000): 1123 0,2,3= from MSP34xx 1124 1= FM stereo Radio from Tuner */ 1125 .pll = PLL_28, 1126 .tuner_type = UNSET, 1127 .tuner_addr = ADDR_UNSET, 1128 }, 1129 [BTTV_BOARD_TVIEW_RDS_FM] = { 1130 /* Claas Langbehn <claas@bigfoot.com>, 1131 Sven Grothklags <sven@upb.de> */ 1132 .name = "Typhoon TView RDS + FM Stereo / KNC1 TV Station RDS", 1133 .video_inputs = 4, 1134 /* .audio_inputs= 3, */ 1135 .svhs = 2, 1136 .gpiomask = 0x1c, 1137 .muxsel = MUXSEL(2, 3, 1, 1), 1138 .gpiomux = { 0, 0, 0x10, 8 }, 1139 .gpiomute = 4, 1140 .pll = PLL_28, 1141 .tuner_type = TUNER_PHILIPS_PAL, 1142 .tuner_addr = ADDR_UNSET, 1143 .has_radio = 1, 1144 }, 1145 [BTTV_BOARD_LIFETEC_9415] = { 1146 /* Tim Röstermundt <rosterm@uni-muenster.de> 1147 in de.comp.os.unix.linux.hardware: 1148 options bttv card=0 pll=1 radio=1 gpiomask=0x18e0 1149 gpiomux =0x44c71f,0x44d71f,0,0x44d71f,0x44dfff 1150 options tuner type=5 */ 1151 .name = "Lifeview FlyVideo 2000 /FlyVideo A2/ Lifetec LT 9415 TV [LR90]", 1152 .video_inputs = 4, 1153 /* .audio_inputs= 1, */ 1154 .svhs = 2, 1155 .gpiomask = 0x18e0, 1156 .muxsel = MUXSEL(2, 3, 1, 1), 1157 .gpiomux = { 0x0000,0x0800,0x1000,0x1000 }, 1158 .gpiomute = 0x18e0, 1159 /* For cards with tda9820/tda9821: 1160 0x0000: Tuner normal stereo 1161 0x0080: Tuner A2 SAP (second audio program = Zweikanalton) 1162 0x0880: Tuner A2 stereo */ 1163 .pll = PLL_28, 1164 .tuner_type = UNSET, 1165 .tuner_addr = ADDR_UNSET, 1166 }, 1167 [BTTV_BOARD_BESTBUY_EASYTV] = { 1168 /* Miguel Angel Alvarez <maacruz@navegalia.com> 1169 old Easy TV BT848 version (model CPH031) */ 1170 .name = "Askey CPH031/ BESTBUY Easy TV", 1171 .video_inputs = 4, 1172 /* .audio_inputs= 1, */ 1173 .svhs = 2, 1174 .gpiomask = 0xF, 1175 .muxsel = MUXSEL(2, 3, 1, 0), 1176 .gpiomux = { 2, 0, 0, 0 }, 1177 .gpiomute = 10, 1178 .pll = PLL_28, 1179 .tuner_type = TUNER_TEMIC_PAL, 1180 .tuner_addr = ADDR_UNSET, 1181 }, 1182 1183 /* ---- card 0x38 ---------------------------------- */ 1184 [BTTV_BOARD_FLYVIDEO_98FM] = { 1185 /* Gordon Heydon <gjheydon@bigfoot.com ('98) */ 1186 .name = "Lifeview FlyVideo 98FM LR50", 1187 .video_inputs = 4, 1188 /* .audio_inputs= 3, */ 1189 .svhs = 2, 1190 .gpiomask = 0x1800, 1191 .muxsel = MUXSEL(2, 3, 1, 1), 1192 .gpiomux = { 0, 0x800, 0x1000, 0x1000 }, 1193 .gpiomute = 0x1800, 1194 .pll = PLL_28, 1195 .tuner_type = TUNER_PHILIPS_PAL, 1196 .tuner_addr = ADDR_UNSET, 1197 }, 1198 /* This is the ultimate cheapo capture card 1199 * just a BT848A on a small PCB! 1200 * Steve Hosgood <steve@equiinet.com> */ 1201 [BTTV_BOARD_GRANDTEC] = { 1202 .name = "GrandTec 'Grand Video Capture' (Bt848)", 1203 .video_inputs = 2, 1204 /* .audio_inputs= 0, */ 1205 .svhs = 1, 1206 .gpiomask = 0, 1207 .muxsel = MUXSEL(3, 1), 1208 .gpiomux = { 0 }, 1209 .no_msp34xx = 1, 1210 .pll = PLL_35, 1211 .tuner_type = TUNER_ABSENT, 1212 .tuner_addr = ADDR_UNSET, 1213 }, 1214 [BTTV_BOARD_ASKEY_CPH060] = { 1215 /* Daniel Herrington <daniel.herrington@home.com> */ 1216 .name = "Askey CPH060/ Phoebe TV Master Only (No FM)", 1217 .video_inputs = 3, 1218 /* .audio_inputs= 1, */ 1219 .svhs = 2, 1220 .gpiomask = 0xe00, 1221 .muxsel = MUXSEL(2, 3, 1, 1), 1222 .gpiomux = { 0x400, 0x400, 0x400, 0x400 }, 1223 .gpiomute = 0x800, 1224 .pll = PLL_28, 1225 .tuner_type = TUNER_TEMIC_4036FY5_NTSC, 1226 .tuner_addr = ADDR_UNSET, 1227 }, 1228 [BTTV_BOARD_ASKEY_CPH03X] = { 1229 /* Matti Mottus <mottus@physic.ut.ee> */ 1230 .name = "Askey CPH03x TV Capturer", 1231 .video_inputs = 4, 1232 /* .audio_inputs= 1, */ 1233 .svhs = 2, 1234 .gpiomask = 0x03000F, 1235 .muxsel = MUXSEL(2, 3, 1, 0), 1236 .gpiomux = { 2, 0, 0, 0 }, 1237 .gpiomute = 1, 1238 .pll = PLL_28, 1239 .tuner_type = TUNER_TEMIC_PAL, 1240 .tuner_addr = ADDR_UNSET, 1241 .has_remote = 1, 1242 }, 1243 1244 /* ---- card 0x3c ---------------------------------- */ 1245 [BTTV_BOARD_MM100PCTV] = { 1246 /* Philip Blundell <philb@gnu.org> */ 1247 .name = "Modular Technology MM100PCTV", 1248 .video_inputs = 2, 1249 /* .audio_inputs= 2, */ 1250 .svhs = NO_SVHS, 1251 .gpiomask = 11, 1252 .muxsel = MUXSEL(2, 3, 1, 1), 1253 .gpiomux = { 2, 0, 0, 1 }, 1254 .gpiomute = 8, 1255 .pll = PLL_35, 1256 .tuner_type = TUNER_TEMIC_PAL, 1257 .tuner_addr = ADDR_UNSET, 1258 }, 1259 [BTTV_BOARD_GMV1] = { 1260 /* Adrian Cox <adrian@humboldt.co.uk */ 1261 .name = "AG Electronics GMV1", 1262 .video_inputs = 2, 1263 /* .audio_inputs= 0, */ 1264 .svhs = 1, 1265 .gpiomask = 0xF, 1266 .muxsel = MUXSEL(2, 2), 1267 .gpiomux = { }, 1268 .no_msp34xx = 1, 1269 .pll = PLL_28, 1270 .tuner_type = TUNER_ABSENT, 1271 .tuner_addr = ADDR_UNSET, 1272 }, 1273 [BTTV_BOARD_BESTBUY_EASYTV2] = { 1274 /* Miguel Angel Alvarez <maacruz@navegalia.com> 1275 new Easy TV BT878 version (model CPH061) 1276 special thanks to Informatica Mieres for providing the card */ 1277 .name = "Askey CPH061/ BESTBUY Easy TV (bt878)", 1278 .video_inputs = 3, 1279 /* .audio_inputs= 2, */ 1280 .svhs = 2, 1281 .gpiomask = 0xFF, 1282 .muxsel = MUXSEL(2, 3, 1, 0), 1283 .gpiomux = { 1, 0, 4, 4 }, 1284 .gpiomute = 9, 1285 .pll = PLL_28, 1286 .tuner_type = TUNER_PHILIPS_PAL, 1287 .tuner_addr = ADDR_UNSET, 1288 }, 1289 [BTTV_BOARD_ATI_TVWONDER] = { 1290 /* Lukas Gebauer <geby@volny.cz> */ 1291 .name = "ATI TV-Wonder", 1292 .video_inputs = 3, 1293 /* .audio_inputs= 1, */ 1294 .svhs = 2, 1295 .gpiomask = 0xf03f, 1296 .muxsel = MUXSEL(2, 3, 1, 0), 1297 .gpiomux = { 0xbffe, 0, 0xbfff, 0 }, 1298 .gpiomute = 0xbffe, 1299 .pll = PLL_28, 1300 .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL, 1301 .tuner_addr = ADDR_UNSET, 1302 }, 1303 1304 /* ---- card 0x40 ---------------------------------- */ 1305 [BTTV_BOARD_ATI_TVWONDERVE] = { 1306 /* Lukas Gebauer <geby@volny.cz> */ 1307 .name = "ATI TV-Wonder VE", 1308 .video_inputs = 2, 1309 /* .audio_inputs= 1, */ 1310 .svhs = NO_SVHS, 1311 .gpiomask = 1, 1312 .muxsel = MUXSEL(2, 3, 0, 1), 1313 .gpiomux = { 0, 0, 1, 0 }, 1314 .no_msp34xx = 1, 1315 .pll = PLL_28, 1316 .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL, 1317 .tuner_addr = ADDR_UNSET, 1318 }, 1319 [BTTV_BOARD_FLYVIDEO2000] = { 1320 /* DeeJay <deejay@westel900.net (2000S) */ 1321 .name = "Lifeview FlyVideo 2000S LR90", 1322 .video_inputs = 3, 1323 /* .audio_inputs= 3, */ 1324 .svhs = 2, 1325 .gpiomask = 0x18e0, 1326 .muxsel = MUXSEL(2, 3, 0, 1), 1327 /* Radio changed from 1e80 to 0x800 to make 1328 FlyVideo2000S in .hu happy (gm)*/ 1329 /* -dk-???: set mute=0x1800 for tda9874h daughterboard */ 1330 .gpiomux = { 0x0000,0x0800,0x1000,0x1000 }, 1331 .gpiomute = 0x1800, 1332 .audio_mode_gpio= fv2000s_audio, 1333 .no_msp34xx = 1, 1334 .pll = PLL_28, 1335 .tuner_type = TUNER_PHILIPS_PAL, 1336 .tuner_addr = ADDR_UNSET, 1337 }, 1338 [BTTV_BOARD_TERRATVALUER] = { 1339 .name = "Terratec TValueRadio", 1340 .video_inputs = 3, 1341 /* .audio_inputs= 1, */ 1342 .svhs = 2, 1343 .gpiomask = 0xffff00, 1344 .muxsel = MUXSEL(2, 3, 1, 1), 1345 .gpiomux = { 0x500, 0x500, 0x300, 0x900 }, 1346 .gpiomute = 0x900, 1347 .pll = PLL_28, 1348 .tuner_type = TUNER_PHILIPS_PAL, 1349 .tuner_addr = ADDR_UNSET, 1350 .has_radio = 1, 1351 }, 1352 [BTTV_BOARD_GVBCTV4PCI] = { 1353 /* TANAKA Kei <peg00625@nifty.com> */ 1354 .name = "IODATA GV-BCTV4/PCI", 1355 .video_inputs = 3, 1356 /* .audio_inputs= 1, */ 1357 .svhs = 2, 1358 .gpiomask = 0x010f00, 1359 .muxsel = MUXSEL(2, 3, 0, 0), 1360 .gpiomux = {0x10000, 0, 0x10000, 0 }, 1361 .no_msp34xx = 1, 1362 .pll = PLL_28, 1363 .tuner_type = TUNER_SHARP_2U5JF5540_NTSC, 1364 .tuner_addr = ADDR_UNSET, 1365 .audio_mode_gpio= gvbctv3pci_audio, 1366 }, 1367 1368 /* ---- card 0x44 ---------------------------------- */ 1369 [BTTV_BOARD_VOODOOTV_FM] = { 1370 .name = "3Dfx VoodooTV FM (Euro)", 1371 /* try "insmod msp3400 simple=0" if you have 1372 * sound problems with this card. */ 1373 .video_inputs = 4, 1374 /* .audio_inputs= 1, */ 1375 .svhs = NO_SVHS, 1376 .gpiomask = 0x4f8a00, 1377 /* 0x100000: 1=MSP enabled (0=disable again) 1378 * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */ 1379 .gpiomux = {0x947fff, 0x987fff,0x947fff,0x947fff }, 1380 .gpiomute = 0x947fff, 1381 /* tvtuner, radio, external,internal, mute, stereo 1382 * tuner, Composite, SVid, Composite-on-Svid-adapter */ 1383 .muxsel = MUXSEL(2, 3, 0, 1), 1384 .tuner_type = TUNER_MT2032, 1385 .tuner_addr = ADDR_UNSET, 1386 .pll = PLL_28, 1387 .has_radio = 1, 1388 }, 1389 [BTTV_BOARD_VOODOOTV_200] = { 1390 .name = "VoodooTV 200 (USA)", 1391 /* try "insmod msp3400 simple=0" if you have 1392 * sound problems with this card. */ 1393 .video_inputs = 4, 1394 /* .audio_inputs= 1, */ 1395 .svhs = NO_SVHS, 1396 .gpiomask = 0x4f8a00, 1397 /* 0x100000: 1=MSP enabled (0=disable again) 1398 * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */ 1399 .gpiomux = {0x947fff, 0x987fff,0x947fff,0x947fff }, 1400 .gpiomute = 0x947fff, 1401 /* tvtuner, radio, external,internal, mute, stereo 1402 * tuner, Composite, SVid, Composite-on-Svid-adapter */ 1403 .muxsel = MUXSEL(2, 3, 0, 1), 1404 .tuner_type = TUNER_MT2032, 1405 .tuner_addr = ADDR_UNSET, 1406 .pll = PLL_28, 1407 .has_radio = 1, 1408 }, 1409 [BTTV_BOARD_AIMMS] = { 1410 /* Philip Blundell <pb@nexus.co.uk> */ 1411 .name = "Active Imaging AIMMS", 1412 .video_inputs = 1, 1413 /* .audio_inputs= 0, */ 1414 .tuner_type = TUNER_ABSENT, 1415 .tuner_addr = ADDR_UNSET, 1416 .pll = PLL_28, 1417 .muxsel = MUXSEL(2), 1418 .gpiomask = 0 1419 }, 1420 [BTTV_BOARD_PV_BT878P_PLUS] = { 1421 /* Tomasz Pyra <hellfire@sedez.iq.pl> */ 1422 .name = "Prolink Pixelview PV-BT878P+ (Rev.4C,8E)", 1423 .video_inputs = 3, 1424 /* .audio_inputs= 4, */ 1425 .svhs = 2, 1426 .gpiomask = 15, 1427 .muxsel = MUXSEL(2, 3, 1, 1), 1428 .gpiomux = { 0, 0, 11, 7 }, /* TV and Radio with same GPIO ! */ 1429 .gpiomute = 13, 1430 .pll = PLL_28, 1431 .tuner_type = TUNER_LG_PAL_I_FM, 1432 .tuner_addr = ADDR_UNSET, 1433 .has_remote = 1, 1434 /* GPIO wiring: 1435 GPIO0: U4.A0 (hef4052bt) 1436 GPIO1: U4.A1 1437 GPIO2: U4.A1 (second hef4052bt) 1438 GPIO3: U4.nEN, U5.A0, A5.nEN 1439 GPIO8-15: vrd866b ? 1440 */ 1441 }, 1442 [BTTV_BOARD_FLYVIDEO98EZ] = { 1443 .name = "Lifeview FlyVideo 98EZ (capture only) LR51", 1444 .video_inputs = 4, 1445 /* .audio_inputs= 0, */ 1446 .svhs = 2, 1447 /* AV1, AV2, SVHS, CVid adapter on SVHS */ 1448 .muxsel = MUXSEL(2, 3, 1, 1), 1449 .pll = PLL_28, 1450 .no_msp34xx = 1, 1451 .tuner_type = TUNER_ABSENT, 1452 .tuner_addr = ADDR_UNSET, 1453 }, 1454 1455 /* ---- card 0x48 ---------------------------------- */ 1456 [BTTV_BOARD_PV_BT878P_9B] = { 1457 /* Dariusz Kowalewski <darekk@automex.pl> */ 1458 .name = "Prolink Pixelview PV-BT878P+9B (PlayTV Pro rev.9B FM+NICAM)", 1459 .video_inputs = 4, 1460 /* .audio_inputs= 1, */ 1461 .svhs = 2, 1462 .gpiomask = 0x3f, 1463 .muxsel = MUXSEL(2, 3, 1, 1), 1464 .gpiomux = { 0x01, 0x00, 0x03, 0x03 }, 1465 .gpiomute = 0x09, 1466 .no_msp34xx = 1, 1467 .pll = PLL_28, 1468 .tuner_type = TUNER_PHILIPS_PAL, 1469 .tuner_addr = ADDR_UNSET, 1470 .audio_mode_gpio= pvbt878p9b_audio, /* Note: not all cards have stereo */ 1471 .has_radio = 1, /* Note: not all cards have radio */ 1472 .has_remote = 1, 1473 /* GPIO wiring: 1474 GPIO0: A0 hef4052 1475 GPIO1: A1 hef4052 1476 GPIO3: nEN hef4052 1477 GPIO8-15: vrd866b 1478 GPIO20,22,23: R30,R29,R28 1479 */ 1480 }, 1481 [BTTV_BOARD_SENSORAY311_611] = { 1482 /* Clay Kunz <ckunz@mail.arc.nasa.gov> */ 1483 /* you must jumper JP5 for the 311 card (PC/104+) to work */ 1484 .name = "Sensoray 311/611", 1485 .video_inputs = 5, 1486 /* .audio_inputs= 0, */ 1487 .svhs = 4, 1488 .gpiomask = 0, 1489 .muxsel = MUXSEL(2, 3, 1, 0, 0), 1490 .gpiomux = { 0 }, 1491 .tuner_type = TUNER_ABSENT, 1492 .tuner_addr = ADDR_UNSET, 1493 }, 1494 [BTTV_BOARD_RV605] = { 1495 /* Miguel Freitas <miguel@cetuc.puc-rio.br> */ 1496 .name = "RemoteVision MX (RV605)", 1497 .video_inputs = 16, 1498 /* .audio_inputs= 0, */ 1499 .svhs = NO_SVHS, 1500 .gpiomask = 0x00, 1501 .gpiomask2 = 0x07ff, 1502 .muxsel = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3), 1503 .no_msp34xx = 1, 1504 .tuner_type = TUNER_ABSENT, 1505 .tuner_addr = ADDR_UNSET, 1506 .muxsel_hook = rv605_muxsel, 1507 }, 1508 [BTTV_BOARD_POWERCLR_MTV878] = { 1509 .name = "Powercolor MTV878/ MTV878R/ MTV878F", 1510 .video_inputs = 3, 1511 /* .audio_inputs= 2, */ 1512 .svhs = 2, 1513 .gpiomask = 0x1C800F, /* Bit0-2: Audio select, 8-12:remote control 14:remote valid 15:remote reset */ 1514 .muxsel = MUXSEL(2, 1, 1), 1515 .gpiomux = { 0, 1, 2, 2 }, 1516 .gpiomute = 4, 1517 .tuner_type = TUNER_PHILIPS_PAL, 1518 .tuner_addr = ADDR_UNSET, 1519 .pll = PLL_28, 1520 .has_radio = 1, 1521 }, 1522 1523 /* ---- card 0x4c ---------------------------------- */ 1524 [BTTV_BOARD_WINDVR] = { 1525 /* Masaki Suzuki <masaki@btree.org> */ 1526 .name = "Canopus WinDVR PCI (COMPAQ Presario 3524JP, 5112JP)", 1527 .video_inputs = 3, 1528 /* .audio_inputs= 1, */ 1529 .svhs = 2, 1530 .gpiomask = 0x140007, 1531 .muxsel = MUXSEL(2, 3, 1, 1), 1532 .gpiomux = { 0, 1, 2, 3 }, 1533 .gpiomute = 4, 1534 .tuner_type = TUNER_PHILIPS_NTSC, 1535 .tuner_addr = ADDR_UNSET, 1536 .audio_mode_gpio= windvr_audio, 1537 }, 1538 [BTTV_BOARD_GRANDTEC_MULTI] = { 1539 .name = "GrandTec Multi Capture Card (Bt878)", 1540 .video_inputs = 4, 1541 /* .audio_inputs= 0, */ 1542 .svhs = NO_SVHS, 1543 .gpiomask = 0, 1544 .muxsel = MUXSEL(2, 3, 1, 0), 1545 .gpiomux = { 0 }, 1546 .no_msp34xx = 1, 1547 .pll = PLL_28, 1548 .tuner_type = TUNER_ABSENT, 1549 .tuner_addr = ADDR_UNSET, 1550 }, 1551 [BTTV_BOARD_KWORLD] = { 1552 .name = "Jetway TV/Capture JW-TV878-FBK, Kworld KW-TV878RF", 1553 .video_inputs = 4, 1554 /* .audio_inputs= 3, */ 1555 .svhs = 2, 1556 .gpiomask = 7, 1557 /* Tuner, SVid, SVHS, SVid to SVHS connector */ 1558 .muxsel = MUXSEL(2, 3, 1, 1), 1559 .gpiomux = { 0, 0, 4, 4 },/* Yes, this tuner uses the same audio output for TV and FM radio! 1560 * This card lacks external Audio In, so we mute it on Ext. & Int. 1561 * The PCB can take a sbx1637/sbx1673, wiring unknown. 1562 * This card lacks PCI subsystem ID, sigh. 1563 * gpiomux =1: lower volume, 2+3: mute 1564 * btwincap uses 0x80000/0x80003 1565 */ 1566 .gpiomute = 4, 1567 .no_msp34xx = 1, 1568 .pll = PLL_28, 1569 .tuner_type = TUNER_PHILIPS_PAL, 1570 .tuner_addr = ADDR_UNSET, 1571 /* Samsung TCPA9095PC27A (BG+DK), philips compatible, w/FM, stereo and 1572 radio signal strength indicators work fine. */ 1573 .has_radio = 1, 1574 /* GPIO Info: 1575 GPIO0,1: HEF4052 A0,A1 1576 GPIO2: HEF4052 nENABLE 1577 GPIO3-7: n.c. 1578 GPIO8-13: IRDC357 data0-5 (data6 n.c. ?) [chip not present on my card] 1579 GPIO14,15: ?? 1580 GPIO16-21: n.c. 1581 GPIO22,23: ?? 1582 ?? : mtu8b56ep microcontroller for IR (GPIO wiring unknown)*/ 1583 }, 1584 [BTTV_BOARD_DSP_TCVIDEO] = { 1585 /* Arthur Tetzlaff-Deas, DSP Design Ltd <software@dspdesign.com> */ 1586 .name = "DSP Design TCVIDEO", 1587 .video_inputs = 4, 1588 .svhs = NO_SVHS, 1589 .muxsel = MUXSEL(2, 3, 1, 0), 1590 .pll = PLL_28, 1591 .tuner_type = UNSET, 1592 .tuner_addr = ADDR_UNSET, 1593 }, 1594 1595 /* ---- card 0x50 ---------------------------------- */ 1596 [BTTV_BOARD_HAUPPAUGEPVR] = { 1597 .name = "Hauppauge WinTV PVR", 1598 .video_inputs = 4, 1599 /* .audio_inputs= 1, */ 1600 .svhs = 2, 1601 .muxsel = MUXSEL(2, 0, 1, 1), 1602 .pll = PLL_28, 1603 .tuner_type = UNSET, 1604 .tuner_addr = ADDR_UNSET, 1605 1606 .gpiomask = 7, 1607 .gpiomux = {7}, 1608 }, 1609 [BTTV_BOARD_GVBCTV5PCI] = { 1610 .name = "IODATA GV-BCTV5/PCI", 1611 .video_inputs = 3, 1612 /* .audio_inputs= 1, */ 1613 .svhs = 2, 1614 .gpiomask = 0x0f0f80, 1615 .muxsel = MUXSEL(2, 3, 1, 0), 1616 .gpiomux = {0x030000, 0x010000, 0, 0 }, 1617 .gpiomute = 0x020000, 1618 .no_msp34xx = 1, 1619 .pll = PLL_28, 1620 .tuner_type = TUNER_PHILIPS_NTSC_M, 1621 .tuner_addr = ADDR_UNSET, 1622 .audio_mode_gpio= gvbctv5pci_audio, 1623 .has_radio = 1, 1624 }, 1625 [BTTV_BOARD_OSPREY1x0] = { 1626 .name = "Osprey 100/150 (878)", /* 0x1(2|3)-45C6-C1 */ 1627 .video_inputs = 4, /* id-inputs-clock */ 1628 /* .audio_inputs= 0, */ 1629 .svhs = 3, 1630 .muxsel = MUXSEL(3, 2, 0, 1), 1631 .pll = PLL_28, 1632 .tuner_type = TUNER_ABSENT, 1633 .tuner_addr = ADDR_UNSET, 1634 .no_msp34xx = 1, 1635 .no_tda7432 = 1, 1636 }, 1637 [BTTV_BOARD_OSPREY1x0_848] = { 1638 .name = "Osprey 100/150 (848)", /* 0x04-54C0-C1 & older boards */ 1639 .video_inputs = 3, 1640 /* .audio_inputs= 0, */ 1641 .svhs = 2, 1642 .muxsel = MUXSEL(2, 3, 1), 1643 .pll = PLL_28, 1644 .tuner_type = TUNER_ABSENT, 1645 .tuner_addr = ADDR_UNSET, 1646 .no_msp34xx = 1, 1647 .no_tda7432 = 1, 1648 }, 1649 1650 /* ---- card 0x54 ---------------------------------- */ 1651 [BTTV_BOARD_OSPREY101_848] = { 1652 .name = "Osprey 101 (848)", /* 0x05-40C0-C1 */ 1653 .video_inputs = 2, 1654 /* .audio_inputs= 0, */ 1655 .svhs = 1, 1656 .muxsel = MUXSEL(3, 1), 1657 .pll = PLL_28, 1658 .tuner_type = TUNER_ABSENT, 1659 .tuner_addr = ADDR_UNSET, 1660 .no_msp34xx = 1, 1661 .no_tda7432 = 1, 1662 }, 1663 [BTTV_BOARD_OSPREY1x1] = { 1664 .name = "Osprey 101/151", /* 0x1(4|5)-0004-C4 */ 1665 .video_inputs = 1, 1666 /* .audio_inputs= 0, */ 1667 .svhs = NO_SVHS, 1668 .muxsel = MUXSEL(0), 1669 .pll = PLL_28, 1670 .tuner_type = TUNER_ABSENT, 1671 .tuner_addr = ADDR_UNSET, 1672 .no_msp34xx = 1, 1673 .no_tda7432 = 1, 1674 }, 1675 [BTTV_BOARD_OSPREY1x1_SVID] = { 1676 .name = "Osprey 101/151 w/ svid", /* 0x(16|17|20)-00C4-C1 */ 1677 .video_inputs = 2, 1678 /* .audio_inputs= 0, */ 1679 .svhs = 1, 1680 .muxsel = MUXSEL(0, 1), 1681 .pll = PLL_28, 1682 .tuner_type = TUNER_ABSENT, 1683 .tuner_addr = ADDR_UNSET, 1684 .no_msp34xx = 1, 1685 .no_tda7432 = 1, 1686 }, 1687 [BTTV_BOARD_OSPREY2xx] = { 1688 .name = "Osprey 200/201/250/251", /* 0x1(8|9|E|F)-0004-C4 */ 1689 .video_inputs = 1, 1690 /* .audio_inputs= 1, */ 1691 .svhs = NO_SVHS, 1692 .muxsel = MUXSEL(0), 1693 .pll = PLL_28, 1694 .tuner_type = TUNER_ABSENT, 1695 .tuner_addr = ADDR_UNSET, 1696 .no_msp34xx = 1, 1697 .no_tda7432 = 1, 1698 }, 1699 1700 /* ---- card 0x58 ---------------------------------- */ 1701 [BTTV_BOARD_OSPREY2x0_SVID] = { 1702 .name = "Osprey 200/250", /* 0x1(A|B)-00C4-C1 */ 1703 .video_inputs = 2, 1704 /* .audio_inputs= 1, */ 1705 .svhs = 1, 1706 .muxsel = MUXSEL(0, 1), 1707 .pll = PLL_28, 1708 .tuner_type = TUNER_ABSENT, 1709 .tuner_addr = ADDR_UNSET, 1710 .no_msp34xx = 1, 1711 .no_tda7432 = 1, 1712 }, 1713 [BTTV_BOARD_OSPREY2x0] = { 1714 .name = "Osprey 210/220/230", /* 0x1(A|B)-04C0-C1 */ 1715 .video_inputs = 2, 1716 /* .audio_inputs= 1, */ 1717 .svhs = 1, 1718 .muxsel = MUXSEL(2, 3), 1719 .pll = PLL_28, 1720 .tuner_type = TUNER_ABSENT, 1721 .tuner_addr = ADDR_UNSET, 1722 .no_msp34xx = 1, 1723 .no_tda7432 = 1, 1724 }, 1725 [BTTV_BOARD_OSPREY500] = { 1726 .name = "Osprey 500", /* 500 */ 1727 .video_inputs = 2, 1728 /* .audio_inputs= 1, */ 1729 .svhs = 1, 1730 .muxsel = MUXSEL(2, 3), 1731 .pll = PLL_28, 1732 .tuner_type = TUNER_ABSENT, 1733 .tuner_addr = ADDR_UNSET, 1734 .no_msp34xx = 1, 1735 .no_tda7432 = 1, 1736 }, 1737 [BTTV_BOARD_OSPREY540] = { 1738 .name = "Osprey 540", /* 540 */ 1739 .video_inputs = 4, 1740 /* .audio_inputs= 1, */ 1741 .pll = PLL_28, 1742 .tuner_type = TUNER_ABSENT, 1743 .tuner_addr = ADDR_UNSET, 1744 .no_msp34xx = 1, 1745 .no_tda7432 = 1, 1746 }, 1747 1748 /* ---- card 0x5C ---------------------------------- */ 1749 [BTTV_BOARD_OSPREY2000] = { 1750 .name = "Osprey 2000", /* 2000 */ 1751 .video_inputs = 2, 1752 /* .audio_inputs= 1, */ 1753 .svhs = 1, 1754 .muxsel = MUXSEL(2, 3), 1755 .pll = PLL_28, 1756 .tuner_type = TUNER_ABSENT, 1757 .tuner_addr = ADDR_UNSET, 1758 .no_msp34xx = 1, 1759 .no_tda7432 = 1, /* must avoid, conflicts with the bt860 */ 1760 }, 1761 [BTTV_BOARD_IDS_EAGLE] = { 1762 /* M G Berberich <berberic@forwiss.uni-passau.de> */ 1763 .name = "IDS Eagle", 1764 .video_inputs = 4, 1765 /* .audio_inputs= 0, */ 1766 .tuner_type = TUNER_ABSENT, 1767 .tuner_addr = ADDR_UNSET, 1768 .svhs = NO_SVHS, 1769 .gpiomask = 0, 1770 .muxsel = MUXSEL(2, 2, 2, 2), 1771 .muxsel_hook = eagle_muxsel, 1772 .no_msp34xx = 1, 1773 .pll = PLL_28, 1774 }, 1775 [BTTV_BOARD_PINNACLESAT] = { 1776 .name = "Pinnacle PCTV Sat", 1777 .video_inputs = 2, 1778 /* .audio_inputs= 0, */ 1779 .svhs = 1, 1780 .tuner_type = TUNER_ABSENT, 1781 .tuner_addr = ADDR_UNSET, 1782 .no_msp34xx = 1, 1783 .no_tda7432 = 1, 1784 .muxsel = MUXSEL(3, 1), 1785 .pll = PLL_28, 1786 .no_gpioirq = 1, 1787 .has_dvb = 1, 1788 }, 1789 [BTTV_BOARD_FORMAC_PROTV] = { 1790 .name = "Formac ProTV II (bt878)", 1791 .video_inputs = 4, 1792 /* .audio_inputs= 1, */ 1793 .svhs = 3, 1794 .gpiomask = 2, 1795 /* TV, Comp1, Composite over SVID con, SVID */ 1796 .muxsel = MUXSEL(2, 3, 1, 1), 1797 .gpiomux = { 2, 2, 0, 0 }, 1798 .pll = PLL_28, 1799 .has_radio = 1, 1800 .tuner_type = TUNER_PHILIPS_PAL, 1801 .tuner_addr = ADDR_UNSET, 1802 /* sound routing: 1803 GPIO=0x00,0x01,0x03: mute (?) 1804 0x02: both TV and radio (tuner: FM1216/I) 1805 The card has onboard audio connectors labeled "cdrom" and "board", 1806 not soldered here, though unknown wiring. 1807 Card lacks: external audio in, pci subsystem id. 1808 */ 1809 }, 1810 1811 /* ---- card 0x60 ---------------------------------- */ 1812 [BTTV_BOARD_MACHTV] = { 1813 .name = "MachTV", 1814 .video_inputs = 3, 1815 /* .audio_inputs= 1, */ 1816 .svhs = NO_SVHS, 1817 .gpiomask = 7, 1818 .muxsel = MUXSEL(2, 3, 1, 1), 1819 .gpiomux = { 0, 1, 2, 3}, 1820 .gpiomute = 4, 1821 .tuner_type = TUNER_PHILIPS_PAL, 1822 .tuner_addr = ADDR_UNSET, 1823 .pll = PLL_28, 1824 }, 1825 [BTTV_BOARD_EURESYS_PICOLO] = { 1826 .name = "Euresys Picolo", 1827 .video_inputs = 3, 1828 /* .audio_inputs= 0, */ 1829 .svhs = 2, 1830 .gpiomask = 0, 1831 .no_msp34xx = 1, 1832 .no_tda7432 = 1, 1833 .muxsel = MUXSEL(2, 0, 1), 1834 .pll = PLL_28, 1835 .tuner_type = TUNER_ABSENT, 1836 .tuner_addr = ADDR_UNSET, 1837 }, 1838 [BTTV_BOARD_PV150] = { 1839 /* Luc Van Hoeylandt <luc@e-magic.be> */ 1840 .name = "ProVideo PV150", /* 0x4f */ 1841 .video_inputs = 2, 1842 /* .audio_inputs= 0, */ 1843 .svhs = NO_SVHS, 1844 .gpiomask = 0, 1845 .muxsel = MUXSEL(2, 3), 1846 .gpiomux = { 0 }, 1847 .no_msp34xx = 1, 1848 .pll = PLL_28, 1849 .tuner_type = TUNER_ABSENT, 1850 .tuner_addr = ADDR_UNSET, 1851 }, 1852 [BTTV_BOARD_AD_TVK503] = { 1853 /* Hiroshi Takekawa <sian@big.or.jp> */ 1854 /* This card lacks subsystem ID */ 1855 .name = "AD-TVK503", /* 0x63 */ 1856 .video_inputs = 4, 1857 /* .audio_inputs= 1, */ 1858 .svhs = 2, 1859 .gpiomask = 0x001e8007, 1860 .muxsel = MUXSEL(2, 3, 1, 0), 1861 /* Tuner, Radio, external, internal, off, on */ 1862 .gpiomux = { 0x08, 0x0f, 0x0a, 0x08 }, 1863 .gpiomute = 0x0f, 1864 .no_msp34xx = 1, 1865 .pll = PLL_28, 1866 .tuner_type = TUNER_PHILIPS_NTSC, 1867 .tuner_addr = ADDR_UNSET, 1868 .audio_mode_gpio= adtvk503_audio, 1869 }, 1870 1871 /* ---- card 0x64 ---------------------------------- */ 1872 [BTTV_BOARD_HERCULES_SM_TV] = { 1873 .name = "Hercules Smart TV Stereo", 1874 .video_inputs = 4, 1875 /* .audio_inputs= 1, */ 1876 .svhs = 2, 1877 .gpiomask = 0x00, 1878 .muxsel = MUXSEL(2, 3, 1, 1), 1879 .no_msp34xx = 1, 1880 .pll = PLL_28, 1881 .tuner_type = TUNER_PHILIPS_PAL, 1882 .tuner_addr = ADDR_UNSET, 1883 /* Notes: 1884 - card lacks subsystem ID 1885 - stereo variant w/ daughter board with tda9874a @0xb0 1886 - Audio Routing: 1887 always from tda9874 independent of GPIO (?) 1888 external line in: unknown 1889 - Other chips: em78p156elp @ 0x96 (probably IR remote control) 1890 hef4053 (instead 4052) for unknown function 1891 */ 1892 }, 1893 [BTTV_BOARD_PACETV] = { 1894 .name = "Pace TV & Radio Card", 1895 .video_inputs = 4, 1896 /* .audio_inputs= 1, */ 1897 .svhs = 2, 1898 /* Tuner, CVid, SVid, CVid over SVid connector */ 1899 .muxsel = MUXSEL(2, 3, 1, 1), 1900 .gpiomask = 0, 1901 .no_tda7432 = 1, 1902 .tuner_type = TUNER_PHILIPS_PAL_I, 1903 .tuner_addr = ADDR_UNSET, 1904 .has_radio = 1, 1905 .pll = PLL_28, 1906 /* Bt878, Bt832, FI1246 tuner; no pci subsystem id 1907 only internal line out: (4pin header) RGGL 1908 Radio must be decoded by msp3410d (not routed through)*/ 1909 /* 1910 .digital_mode = DIGITAL_MODE_CAMERA, todo! 1911 */ 1912 }, 1913 [BTTV_BOARD_IVC200] = { 1914 /* Chris Willing <chris@vislab.usyd.edu.au> */ 1915 .name = "IVC-200", 1916 .video_inputs = 1, 1917 /* .audio_inputs= 0, */ 1918 .tuner_type = TUNER_ABSENT, 1919 .tuner_addr = ADDR_UNSET, 1920 .svhs = NO_SVHS, 1921 .gpiomask = 0xdf, 1922 .muxsel = MUXSEL(2), 1923 .pll = PLL_28, 1924 }, 1925 [BTTV_BOARD_IVCE8784] = { 1926 .name = "IVCE-8784", 1927 .video_inputs = 1, 1928 /* .audio_inputs= 0, */ 1929 .tuner_type = TUNER_ABSENT, 1930 .tuner_addr = ADDR_UNSET, 1931 .svhs = NO_SVHS, 1932 .gpiomask = 0xdf, 1933 .muxsel = MUXSEL(2), 1934 .pll = PLL_28, 1935 }, 1936 [BTTV_BOARD_XGUARD] = { 1937 .name = "Grand X-Guard / Trust 814PCI", 1938 .video_inputs = 16, 1939 /* .audio_inputs= 0, */ 1940 .svhs = NO_SVHS, 1941 .tuner_type = TUNER_ABSENT, 1942 .tuner_addr = ADDR_UNSET, 1943 .gpiomask2 = 0xff, 1944 .muxsel = MUXSEL(2,2,2,2, 3,3,3,3, 1,1,1,1, 0,0,0,0), 1945 .muxsel_hook = xguard_muxsel, 1946 .no_msp34xx = 1, 1947 .no_tda7432 = 1, 1948 .pll = PLL_28, 1949 }, 1950 1951 /* ---- card 0x68 ---------------------------------- */ 1952 [BTTV_BOARD_NEBULA_DIGITV] = { 1953 .name = "Nebula Electronics DigiTV", 1954 .video_inputs = 1, 1955 .svhs = NO_SVHS, 1956 .muxsel = MUXSEL(2, 3, 1, 0), 1957 .no_msp34xx = 1, 1958 .no_tda7432 = 1, 1959 .pll = PLL_28, 1960 .tuner_type = TUNER_ABSENT, 1961 .tuner_addr = ADDR_UNSET, 1962 .has_dvb = 1, 1963 .has_remote = 1, 1964 .gpiomask = 0x1b, 1965 .no_gpioirq = 1, 1966 }, 1967 [BTTV_BOARD_PV143] = { 1968 /* Jorge Boncompte - DTI2 <jorge@dti2.net> */ 1969 .name = "ProVideo PV143", 1970 .video_inputs = 4, 1971 /* .audio_inputs= 0, */ 1972 .svhs = NO_SVHS, 1973 .gpiomask = 0, 1974 .muxsel = MUXSEL(2, 3, 1, 0), 1975 .gpiomux = { 0 }, 1976 .no_msp34xx = 1, 1977 .pll = PLL_28, 1978 .tuner_type = TUNER_ABSENT, 1979 .tuner_addr = ADDR_UNSET, 1980 }, 1981 [BTTV_BOARD_VD009X1_VD011_MINIDIN] = { 1982 /* M.Klahr@phytec.de */ 1983 .name = "PHYTEC VD-009-X1 VD-011 MiniDIN (bt878)", 1984 .video_inputs = 4, 1985 /* .audio_inputs= 0, */ 1986 .svhs = 3, 1987 .gpiomask = 0x00, 1988 .muxsel = MUXSEL(2, 3, 1, 0), 1989 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 1990 .pll = PLL_28, 1991 .tuner_type = TUNER_ABSENT, 1992 .tuner_addr = ADDR_UNSET, 1993 }, 1994 [BTTV_BOARD_VD009X1_VD011_COMBI] = { 1995 .name = "PHYTEC VD-009-X1 VD-011 Combi (bt878)", 1996 .video_inputs = 4, 1997 /* .audio_inputs= 0, */ 1998 .svhs = 3, 1999 .gpiomask = 0x00, 2000 .muxsel = MUXSEL(2, 3, 1, 1), 2001 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2002 .pll = PLL_28, 2003 .tuner_type = TUNER_ABSENT, 2004 .tuner_addr = ADDR_UNSET, 2005 }, 2006 2007 /* ---- card 0x6c ---------------------------------- */ 2008 [BTTV_BOARD_VD009_MINIDIN] = { 2009 .name = "PHYTEC VD-009 MiniDIN (bt878)", 2010 .video_inputs = 10, 2011 /* .audio_inputs= 0, */ 2012 .svhs = 9, 2013 .gpiomask = 0x00, 2014 .gpiomask2 = 0x03, /* used for external vodeo mux */ 2015 .muxsel = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 0), 2016 .muxsel_hook = phytec_muxsel, 2017 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2018 .pll = PLL_28, 2019 .tuner_type = TUNER_ABSENT, 2020 .tuner_addr = ADDR_UNSET, 2021 }, 2022 [BTTV_BOARD_VD009_COMBI] = { 2023 .name = "PHYTEC VD-009 Combi (bt878)", 2024 .video_inputs = 10, 2025 /* .audio_inputs= 0, */ 2026 .svhs = 9, 2027 .gpiomask = 0x00, 2028 .gpiomask2 = 0x03, /* used for external vodeo mux */ 2029 .muxsel = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 1), 2030 .muxsel_hook = phytec_muxsel, 2031 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2032 .pll = PLL_28, 2033 .tuner_type = TUNER_ABSENT, 2034 .tuner_addr = ADDR_UNSET, 2035 }, 2036 [BTTV_BOARD_IVC100] = { 2037 .name = "IVC-100", 2038 .video_inputs = 4, 2039 /* .audio_inputs= 0, */ 2040 .tuner_type = TUNER_ABSENT, 2041 .tuner_addr = ADDR_UNSET, 2042 .svhs = NO_SVHS, 2043 .gpiomask = 0xdf, 2044 .muxsel = MUXSEL(2, 3, 1, 0), 2045 .pll = PLL_28, 2046 }, 2047 [BTTV_BOARD_IVC120] = { 2048 /* IVC-120G - Alan Garfield <alan@fromorbit.com> */ 2049 .name = "IVC-120G", 2050 .video_inputs = 16, 2051 /* .audio_inputs= 0, */ 2052 .tuner_type = TUNER_ABSENT, 2053 .tuner_addr = ADDR_UNSET, 2054 .svhs = NO_SVHS, /* card has no svhs */ 2055 .no_msp34xx = 1, 2056 .no_tda7432 = 1, 2057 .gpiomask = 0x00, 2058 .muxsel = MUXSEL(0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0), 2059 .muxsel_hook = ivc120_muxsel, 2060 .pll = PLL_28, 2061 }, 2062 2063 /* ---- card 0x70 ---------------------------------- */ 2064 [BTTV_BOARD_PC_HDTV] = { 2065 .name = "pcHDTV HD-2000 TV", 2066 .video_inputs = 4, 2067 /* .audio_inputs= 1, */ 2068 .svhs = 2, 2069 .muxsel = MUXSEL(2, 3, 1, 0), 2070 .tuner_type = TUNER_PHILIPS_FCV1236D, 2071 .tuner_addr = ADDR_UNSET, 2072 .has_dvb = 1, 2073 }, 2074 [BTTV_BOARD_TWINHAN_DST] = { 2075 .name = "Twinhan DST + clones", 2076 .no_msp34xx = 1, 2077 .no_tda7432 = 1, 2078 .tuner_type = TUNER_ABSENT, 2079 .tuner_addr = ADDR_UNSET, 2080 .no_video = 1, 2081 .has_dvb = 1, 2082 }, 2083 [BTTV_BOARD_WINFASTVC100] = { 2084 .name = "Winfast VC100", 2085 .video_inputs = 3, 2086 /* .audio_inputs= 0, */ 2087 .svhs = 1, 2088 /* Vid In, SVid In, Vid over SVid in connector */ 2089 .muxsel = MUXSEL(3, 1, 1, 3), 2090 .no_msp34xx = 1, 2091 .no_tda7432 = 1, 2092 .tuner_type = TUNER_ABSENT, 2093 .tuner_addr = ADDR_UNSET, 2094 .pll = PLL_28, 2095 }, 2096 [BTTV_BOARD_TEV560] = { 2097 .name = "Teppro TEV-560/InterVision IV-560", 2098 .video_inputs = 3, 2099 /* .audio_inputs= 1, */ 2100 .svhs = 2, 2101 .gpiomask = 3, 2102 .muxsel = MUXSEL(2, 3, 1, 1), 2103 .gpiomux = { 1, 1, 1, 1 }, 2104 .tuner_type = TUNER_PHILIPS_PAL, 2105 .tuner_addr = ADDR_UNSET, 2106 .pll = PLL_35, 2107 }, 2108 2109 /* ---- card 0x74 ---------------------------------- */ 2110 [BTTV_BOARD_SIMUS_GVC1100] = { 2111 .name = "SIMUS GVC1100", 2112 .video_inputs = 4, 2113 /* .audio_inputs= 0, */ 2114 .svhs = NO_SVHS, 2115 .tuner_type = TUNER_ABSENT, 2116 .tuner_addr = ADDR_UNSET, 2117 .pll = PLL_28, 2118 .muxsel = MUXSEL(2, 2, 2, 2), 2119 .gpiomask = 0x3F, 2120 .muxsel_hook = gvc1100_muxsel, 2121 }, 2122 [BTTV_BOARD_NGSTV_PLUS] = { 2123 /* Carlos Silva r3pek@r3pek.homelinux.org || card 0x75 */ 2124 .name = "NGS NGSTV+", 2125 .video_inputs = 3, 2126 .svhs = 2, 2127 .gpiomask = 0x008007, 2128 .muxsel = MUXSEL(2, 3, 0, 0), 2129 .gpiomux = { 0, 0, 0, 0 }, 2130 .gpiomute = 0x000003, 2131 .pll = PLL_28, 2132 .tuner_type = TUNER_PHILIPS_PAL, 2133 .tuner_addr = ADDR_UNSET, 2134 .has_remote = 1, 2135 }, 2136 [BTTV_BOARD_LMLBT4] = { 2137 /* http://linuxmedialabs.com */ 2138 .name = "LMLBT4", 2139 .video_inputs = 4, /* IN1,IN2,IN3,IN4 */ 2140 /* .audio_inputs= 0, */ 2141 .svhs = NO_SVHS, 2142 .muxsel = MUXSEL(2, 3, 1, 0), 2143 .no_msp34xx = 1, 2144 .no_tda7432 = 1, 2145 .tuner_type = TUNER_ABSENT, 2146 .tuner_addr = ADDR_UNSET, 2147 }, 2148 [BTTV_BOARD_TEKRAM_M205] = { 2149 /* Helmroos Harri <harri.helmroos@pp.inet.fi> */ 2150 .name = "Tekram M205 PRO", 2151 .video_inputs = 3, 2152 /* .audio_inputs= 1, */ 2153 .tuner_type = TUNER_PHILIPS_PAL, 2154 .tuner_addr = ADDR_UNSET, 2155 .svhs = 2, 2156 .gpiomask = 0x68, 2157 .muxsel = MUXSEL(2, 3, 1), 2158 .gpiomux = { 0x68, 0x68, 0x61, 0x61 }, 2159 .pll = PLL_28, 2160 }, 2161 2162 /* ---- card 0x78 ---------------------------------- */ 2163 [BTTV_BOARD_CONTVFMI] = { 2164 /* Javier Cendan Ares <jcendan@lycos.es> */ 2165 /* bt878 TV + FM without subsystem ID */ 2166 .name = "Conceptronic CONTVFMi", 2167 .video_inputs = 3, 2168 /* .audio_inputs= 1, */ 2169 .svhs = 2, 2170 .gpiomask = 0x008007, 2171 .muxsel = MUXSEL(2, 3, 1, 1), 2172 .gpiomux = { 0, 1, 2, 2 }, 2173 .gpiomute = 3, 2174 .pll = PLL_28, 2175 .tuner_type = TUNER_PHILIPS_PAL, 2176 .tuner_addr = ADDR_UNSET, 2177 .has_remote = 1, 2178 .has_radio = 1, 2179 }, 2180 [BTTV_BOARD_PICOLO_TETRA_CHIP] = { 2181 /*Eric DEBIEF <debief@telemsa.com>*/ 2182 /*EURESYS Picolo Tetra : 4 Conexant Fusion 878A, no audio, video input set with analog multiplexers GPIO controlled*/ 2183 /* adds picolo_tetra_muxsel(), picolo_tetra_init(), the following declaration strucure, and #define BTTV_BOARD_PICOLO_TETRA_CHIP*/ 2184 /*0x79 in bttv.h*/ 2185 .name = "Euresys Picolo Tetra", 2186 .video_inputs = 4, 2187 /* .audio_inputs= 0, */ 2188 .svhs = NO_SVHS, 2189 .gpiomask = 0, 2190 .gpiomask2 = 0x3C<<16,/*Set the GPIO[18]->GPIO[21] as output pin.==> drive the video inputs through analog multiplexers*/ 2191 .no_msp34xx = 1, 2192 .no_tda7432 = 1, 2193 /*878A input is always MUX0, see above.*/ 2194 .muxsel = MUXSEL(2, 2, 2, 2), 2195 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2196 .pll = PLL_28, 2197 .muxsel_hook = picolo_tetra_muxsel,/*Required as it doesn't follow the classic input selection policy*/ 2198 .tuner_type = TUNER_ABSENT, 2199 .tuner_addr = ADDR_UNSET, 2200 }, 2201 [BTTV_BOARD_SPIRIT_TV] = { 2202 /* Spirit TV Tuner from http://spiritmodems.com.au */ 2203 /* Stafford Goodsell <surge@goliath.homeunix.org> */ 2204 .name = "Spirit TV Tuner", 2205 .video_inputs = 3, 2206 /* .audio_inputs= 1, */ 2207 .svhs = 2, 2208 .gpiomask = 0x0000000f, 2209 .muxsel = MUXSEL(2, 1, 1), 2210 .gpiomux = { 0x02, 0x00, 0x00, 0x00 }, 2211 .tuner_type = TUNER_TEMIC_PAL, 2212 .tuner_addr = ADDR_UNSET, 2213 .no_msp34xx = 1, 2214 }, 2215 [BTTV_BOARD_AVDVBT_771] = { 2216 /* Wolfram Joost <wojo@frokaschwei.de> */ 2217 .name = "AVerMedia AVerTV DVB-T 771", 2218 .video_inputs = 2, 2219 .svhs = 1, 2220 .tuner_type = TUNER_ABSENT, 2221 .tuner_addr = ADDR_UNSET, 2222 .muxsel = MUXSEL(3, 3), 2223 .no_msp34xx = 1, 2224 .no_tda7432 = 1, 2225 .pll = PLL_28, 2226 .has_dvb = 1, 2227 .no_gpioirq = 1, 2228 .has_remote = 1, 2229 }, 2230 /* ---- card 0x7c ---------------------------------- */ 2231 [BTTV_BOARD_AVDVBT_761] = { 2232 /* Matt Jesson <dvb@jesson.eclipse.co.uk> */ 2233 /* Based on the Nebula card data - added remote and new card number - BTTV_BOARD_AVDVBT_761, see also ir-kbd-gpio.c */ 2234 .name = "AverMedia AverTV DVB-T 761", 2235 .video_inputs = 2, 2236 .svhs = 1, 2237 .muxsel = MUXSEL(3, 1, 2, 0), /* Comp0, S-Video, ?, ? */ 2238 .no_msp34xx = 1, 2239 .no_tda7432 = 1, 2240 .pll = PLL_28, 2241 .tuner_type = TUNER_ABSENT, 2242 .tuner_addr = ADDR_UNSET, 2243 .has_dvb = 1, 2244 .no_gpioirq = 1, 2245 .has_remote = 1, 2246 }, 2247 [BTTV_BOARD_MATRIX_VISIONSQ] = { 2248 /* andre.schwarz@matrix-vision.de */ 2249 .name = "MATRIX Vision Sigma-SQ", 2250 .video_inputs = 16, 2251 /* .audio_inputs= 0, */ 2252 .svhs = NO_SVHS, 2253 .gpiomask = 0x0, 2254 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3), 2255 .muxsel_hook = sigmaSQ_muxsel, 2256 .gpiomux = { 0 }, 2257 .no_msp34xx = 1, 2258 .pll = PLL_28, 2259 .tuner_type = TUNER_ABSENT, 2260 .tuner_addr = ADDR_UNSET, 2261 }, 2262 [BTTV_BOARD_MATRIX_VISIONSLC] = { 2263 /* andre.schwarz@matrix-vision.de */ 2264 .name = "MATRIX Vision Sigma-SLC", 2265 .video_inputs = 4, 2266 /* .audio_inputs= 0, */ 2267 .svhs = NO_SVHS, 2268 .gpiomask = 0x0, 2269 .muxsel = MUXSEL(2, 2, 2, 2), 2270 .muxsel_hook = sigmaSLC_muxsel, 2271 .gpiomux = { 0 }, 2272 .no_msp34xx = 1, 2273 .pll = PLL_28, 2274 .tuner_type = TUNER_ABSENT, 2275 .tuner_addr = ADDR_UNSET, 2276 }, 2277 /* BTTV_BOARD_APAC_VIEWCOMP */ 2278 [BTTV_BOARD_APAC_VIEWCOMP] = { 2279 /* Attila Kondoros <attila.kondoros@chello.hu> */ 2280 /* bt878 TV + FM 0x00000000 subsystem ID */ 2281 .name = "APAC Viewcomp 878(AMAX)", 2282 .video_inputs = 2, 2283 /* .audio_inputs= 1, */ 2284 .svhs = NO_SVHS, 2285 .gpiomask = 0xFF, 2286 .muxsel = MUXSEL(2, 3, 1, 1), 2287 .gpiomux = { 2, 0, 0, 0 }, 2288 .gpiomute = 10, 2289 .pll = PLL_28, 2290 .tuner_type = TUNER_PHILIPS_PAL, 2291 .tuner_addr = ADDR_UNSET, 2292 .has_remote = 1, /* miniremote works, see ir-kbd-gpio.c */ 2293 .has_radio = 1, /* not every card has radio */ 2294 }, 2295 2296 /* ---- card 0x80 ---------------------------------- */ 2297 [BTTV_BOARD_DVICO_DVBT_LITE] = { 2298 /* Chris Pascoe <c.pascoe@itee.uq.edu.au> */ 2299 .name = "DViCO FusionHDTV DVB-T Lite", 2300 .no_msp34xx = 1, 2301 .no_tda7432 = 1, 2302 .pll = PLL_28, 2303 .no_video = 1, 2304 .has_dvb = 1, 2305 .tuner_type = TUNER_ABSENT, 2306 .tuner_addr = ADDR_UNSET, 2307 }, 2308 [BTTV_BOARD_VGEAR_MYVCD] = { 2309 /* Steven <photon38@pchome.com.tw> */ 2310 .name = "V-Gear MyVCD", 2311 .video_inputs = 3, 2312 /* .audio_inputs= 1, */ 2313 .svhs = 2, 2314 .gpiomask = 0x3f, 2315 .muxsel = MUXSEL(2, 3, 1, 0), 2316 .gpiomux = {0x31, 0x31, 0x31, 0x31 }, 2317 .gpiomute = 0x31, 2318 .no_msp34xx = 1, 2319 .pll = PLL_28, 2320 .tuner_type = TUNER_PHILIPS_NTSC_M, 2321 .tuner_addr = ADDR_UNSET, 2322 .has_radio = 0, 2323 }, 2324 [BTTV_BOARD_SUPER_TV] = { 2325 /* Rick C <cryptdragoon@gmail.com> */ 2326 .name = "Super TV Tuner", 2327 .video_inputs = 4, 2328 /* .audio_inputs= 1, */ 2329 .svhs = 2, 2330 .muxsel = MUXSEL(2, 3, 1, 0), 2331 .tuner_type = TUNER_PHILIPS_NTSC, 2332 .tuner_addr = ADDR_UNSET, 2333 .gpiomask = 0x008007, 2334 .gpiomux = { 0, 0x000001,0,0 }, 2335 .has_radio = 1, 2336 }, 2337 [BTTV_BOARD_TIBET_CS16] = { 2338 /* Chris Fanning <video4linux@haydon.net> */ 2339 .name = "Tibet Systems 'Progress DVR' CS16", 2340 .video_inputs = 16, 2341 /* .audio_inputs= 0, */ 2342 .svhs = NO_SVHS, 2343 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2), 2344 .pll = PLL_28, 2345 .no_msp34xx = 1, 2346 .no_tda7432 = 1, 2347 .tuner_type = TUNER_ABSENT, 2348 .tuner_addr = ADDR_UNSET, 2349 .muxsel_hook = tibetCS16_muxsel, 2350 }, 2351 [BTTV_BOARD_KODICOM_4400R] = { 2352 /* Bill Brack <wbrack@mmm.com.hk> */ 2353 /* 2354 * Note that, because of the card's wiring, the "master" 2355 * BT878A chip (i.e. the one which controls the analog switch 2356 * and must use this card type) is the 2nd one detected. The 2357 * other 3 chips should use card type 0x85, whose description 2358 * follows this one. There is a EEPROM on the card (which is 2359 * connected to the I2C of one of those other chips), but is 2360 * not currently handled. There is also a facility for a 2361 * "monitor", which is also not currently implemented. 2362 */ 2363 .name = "Kodicom 4400R (master)", 2364 .video_inputs = 16, 2365 /* .audio_inputs= 0, */ 2366 .tuner_type = TUNER_ABSENT, 2367 .tuner_addr = ADDR_UNSET, 2368 .svhs = NO_SVHS, 2369 /* GPIO bits 0-9 used for analog switch: 2370 * 00 - 03: camera selector 2371 * 04 - 06: channel (controller) selector 2372 * 07: data (1->on, 0->off) 2373 * 08: strobe 2374 * 09: reset 2375 * bit 16 is input from sync separator for the channel 2376 */ 2377 .gpiomask = 0x0003ff, 2378 .no_gpioirq = 1, 2379 .muxsel = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3), 2380 .pll = PLL_28, 2381 .no_msp34xx = 1, 2382 .no_tda7432 = 1, 2383 .muxsel_hook = kodicom4400r_muxsel, 2384 }, 2385 [BTTV_BOARD_KODICOM_4400R_SL] = { 2386 /* Bill Brack <wbrack@mmm.com.hk> */ 2387 /* Note that, for reasons unknown, the "master" BT878A chip (i.e. the 2388 * one which controls the analog switch, and must use the card type) 2389 * is the 2nd one detected. The other 3 chips should use this card 2390 * type 2391 */ 2392 .name = "Kodicom 4400R (slave)", 2393 .video_inputs = 16, 2394 /* .audio_inputs= 0, */ 2395 .tuner_type = TUNER_ABSENT, 2396 .tuner_addr = ADDR_UNSET, 2397 .svhs = NO_SVHS, 2398 .gpiomask = 0x010000, 2399 .no_gpioirq = 1, 2400 .muxsel = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3), 2401 .pll = PLL_28, 2402 .no_msp34xx = 1, 2403 .no_tda7432 = 1, 2404 .muxsel_hook = kodicom4400r_muxsel, 2405 }, 2406 /* ---- card 0x86---------------------------------- */ 2407 [BTTV_BOARD_ADLINK_RTV24] = { 2408 /* Michael Henson <mhenson@clarityvi.com> */ 2409 /* Adlink RTV24 with special unlock codes */ 2410 .name = "Adlink RTV24", 2411 .video_inputs = 4, 2412 /* .audio_inputs= 1, */ 2413 .svhs = 2, 2414 .muxsel = MUXSEL(2, 3, 1, 0), 2415 .tuner_type = UNSET, 2416 .tuner_addr = ADDR_UNSET, 2417 .pll = PLL_28, 2418 }, 2419 /* ---- card 0x87---------------------------------- */ 2420 [BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE] = { 2421 /* Michael Krufky <mkrufky@linuxtv.org> */ 2422 .name = "DViCO FusionHDTV 5 Lite", 2423 .tuner_type = TUNER_LG_TDVS_H06XF, /* TDVS-H064F */ 2424 .tuner_addr = ADDR_UNSET, 2425 .video_inputs = 3, 2426 /* .audio_inputs= 1, */ 2427 .svhs = 2, 2428 .muxsel = MUXSEL(2, 3, 1), 2429 .gpiomask = 0x00e00007, 2430 .gpiomux = { 0x00400005, 0, 0x00000001, 0 }, 2431 .gpiomute = 0x00c00007, 2432 .no_msp34xx = 1, 2433 .no_tda7432 = 1, 2434 .has_dvb = 1, 2435 }, 2436 /* ---- card 0x88---------------------------------- */ 2437 [BTTV_BOARD_ACORP_Y878F] = { 2438 /* Mauro Carvalho Chehab <mchehab@kernel.org> */ 2439 .name = "Acorp Y878F", 2440 .video_inputs = 3, 2441 /* .audio_inputs= 1, */ 2442 .svhs = 2, 2443 .gpiomask = 0x01fe00, 2444 .muxsel = MUXSEL(2, 3, 1, 1), 2445 .gpiomux = { 0x001e00, 0, 0x018000, 0x014000 }, 2446 .gpiomute = 0x002000, 2447 .pll = PLL_28, 2448 .tuner_type = TUNER_YMEC_TVF66T5_B_DFF, 2449 .tuner_addr = 0xc1 >>1, 2450 .has_radio = 1, 2451 }, 2452 /* ---- card 0x89 ---------------------------------- */ 2453 [BTTV_BOARD_CONCEPTRONIC_CTVFMI2] = { 2454 .name = "Conceptronic CTVFMi v2", 2455 .video_inputs = 3, 2456 /* .audio_inputs= 1, */ 2457 .svhs = 2, 2458 .gpiomask = 0x001c0007, 2459 .muxsel = MUXSEL(2, 3, 1, 1), 2460 .gpiomux = { 0, 1, 2, 2 }, 2461 .gpiomute = 3, 2462 .pll = PLL_28, 2463 .tuner_type = TUNER_TENA_9533_DI, 2464 .tuner_addr = ADDR_UNSET, 2465 .has_remote = 1, 2466 .has_radio = 1, 2467 }, 2468 /* ---- card 0x8a ---------------------------------- */ 2469 [BTTV_BOARD_PV_BT878P_2E] = { 2470 .name = "Prolink Pixelview PV-BT878P+ (Rev.2E)", 2471 .video_inputs = 5, 2472 /* .audio_inputs= 1, */ 2473 .svhs = 3, 2474 .has_dig_in = 1, 2475 .gpiomask = 0x01fe00, 2476 .muxsel = MUXSEL(2, 3, 1, 1, 0), /* in 4 is digital */ 2477 /* .digital_mode= DIGITAL_MODE_CAMERA, */ 2478 .gpiomux = { 0x00400, 0x10400, 0x04400, 0x80000 }, 2479 .gpiomute = 0x12400, 2480 .no_msp34xx = 1, 2481 .pll = PLL_28, 2482 .tuner_type = TUNER_LG_PAL_FM, 2483 .tuner_addr = ADDR_UNSET, 2484 .has_remote = 1, 2485 }, 2486 /* ---- card 0x8b ---------------------------------- */ 2487 [BTTV_BOARD_PV_M4900] = { 2488 /* Sérgio Fortier <sergiofortier@yahoo.com.br> */ 2489 .name = "Prolink PixelView PlayTV MPEG2 PV-M4900", 2490 .video_inputs = 3, 2491 /* .audio_inputs= 1, */ 2492 .svhs = 2, 2493 .gpiomask = 0x3f, 2494 .muxsel = MUXSEL(2, 3, 1, 1), 2495 .gpiomux = { 0x21, 0x20, 0x24, 0x2c }, 2496 .gpiomute = 0x29, 2497 .no_msp34xx = 1, 2498 .pll = PLL_28, 2499 .tuner_type = TUNER_YMEC_TVF_5533MF, 2500 .tuner_addr = ADDR_UNSET, 2501 .has_radio = 1, 2502 .has_remote = 1, 2503 }, 2504 /* ---- card 0x8c ---------------------------------- */ 2505 /* Has four Bt878 chips behind a PCI bridge, each chip has: 2506 one external BNC composite input (mux 2) 2507 three internal composite inputs (unknown muxes) 2508 an 18-bit stereo A/D (CS5331A), which has: 2509 one external stereo unblanced (RCA) audio connection 2510 one (or 3?) internal stereo balanced (XLR) audio connection 2511 input is selected via gpio to a 14052B mux 2512 (mask=0x300, unbal=0x000, bal=0x100, ??=0x200,0x300) 2513 gain is controlled via an X9221A chip on the I2C bus @0x28 2514 sample rate is controlled via gpio to an MK1413S 2515 (mask=0x3, 32kHz=0x0, 44.1kHz=0x1, 48kHz=0x2, ??=0x3) 2516 There is neither a tuner nor an svideo input. */ 2517 [BTTV_BOARD_OSPREY440] = { 2518 .name = "Osprey 440", 2519 .video_inputs = 4, 2520 /* .audio_inputs= 2, */ 2521 .svhs = NO_SVHS, 2522 .muxsel = MUXSEL(2, 3, 0, 1), /* 3,0,1 are guesses */ 2523 .gpiomask = 0x303, 2524 .gpiomute = 0x000, /* int + 32kHz */ 2525 .gpiomux = { 0, 0, 0x000, 0x100}, 2526 .pll = PLL_28, 2527 .tuner_type = TUNER_ABSENT, 2528 .tuner_addr = ADDR_UNSET, 2529 .no_msp34xx = 1, 2530 .no_tda7432 = 1, 2531 }, 2532 /* ---- card 0x8d ---------------------------------- */ 2533 [BTTV_BOARD_ASOUND_SKYEYE] = { 2534 .name = "Asound Skyeye PCTV", 2535 .video_inputs = 3, 2536 /* .audio_inputs= 1, */ 2537 .svhs = 2, 2538 .gpiomask = 15, 2539 .muxsel = MUXSEL(2, 3, 1, 1), 2540 .gpiomux = { 2, 0, 0, 0 }, 2541 .gpiomute = 1, 2542 .pll = PLL_28, 2543 .tuner_type = TUNER_PHILIPS_NTSC, 2544 .tuner_addr = ADDR_UNSET, 2545 }, 2546 /* ---- card 0x8e ---------------------------------- */ 2547 [BTTV_BOARD_SABRENT_TVFM] = { 2548 .name = "Sabrent TV-FM (bttv version)", 2549 .video_inputs = 3, 2550 /* .audio_inputs= 1, */ 2551 .svhs = 2, 2552 .gpiomask = 0x108007, 2553 .muxsel = MUXSEL(2, 3, 1, 1), 2554 .gpiomux = { 100000, 100002, 100002, 100000 }, 2555 .no_msp34xx = 1, 2556 .no_tda7432 = 1, 2557 .pll = PLL_28, 2558 .tuner_type = TUNER_TNF_5335MF, 2559 .tuner_addr = ADDR_UNSET, 2560 .has_radio = 1, 2561 }, 2562 /* ---- card 0x8f ---------------------------------- */ 2563 [BTTV_BOARD_HAUPPAUGE_IMPACTVCB] = { 2564 .name = "Hauppauge ImpactVCB (bt878)", 2565 .video_inputs = 4, 2566 /* .audio_inputs= 0, */ 2567 .svhs = NO_SVHS, 2568 .gpiomask = 0x0f, /* old: 7 */ 2569 .muxsel = MUXSEL(0, 1, 3, 2), /* Composite 0-3 */ 2570 .no_msp34xx = 1, 2571 .no_tda7432 = 1, 2572 .tuner_type = TUNER_ABSENT, 2573 .tuner_addr = ADDR_UNSET, 2574 }, 2575 [BTTV_BOARD_MACHTV_MAGICTV] = { 2576 /* Julian Calaby <julian.calaby@gmail.com> 2577 * Slightly different from original MachTV definition (0x60) 2578 2579 * FIXME: RegSpy says gpiomask should be "0x001c800f", but it 2580 * stuffs up remote chip. Bug is a pin on the jaecs is not set 2581 * properly (methinks) causing no keyup bits being set */ 2582 2583 .name = "MagicTV", /* rebranded MachTV */ 2584 .video_inputs = 3, 2585 /* .audio_inputs= 1, */ 2586 .svhs = 2, 2587 .gpiomask = 7, 2588 .muxsel = MUXSEL(2, 3, 1, 1), 2589 .gpiomux = { 0, 1, 2, 3 }, 2590 .gpiomute = 4, 2591 .tuner_type = TUNER_TEMIC_4009FR5_PAL, 2592 .tuner_addr = ADDR_UNSET, 2593 .pll = PLL_28, 2594 .has_radio = 1, 2595 .has_remote = 1, 2596 }, 2597 [BTTV_BOARD_SSAI_SECURITY] = { 2598 .name = "SSAI Security Video Interface", 2599 .video_inputs = 4, 2600 /* .audio_inputs= 0, */ 2601 .svhs = NO_SVHS, 2602 .muxsel = MUXSEL(0, 1, 2, 3), 2603 .tuner_type = TUNER_ABSENT, 2604 .tuner_addr = ADDR_UNSET, 2605 }, 2606 [BTTV_BOARD_SSAI_ULTRASOUND] = { 2607 .name = "SSAI Ultrasound Video Interface", 2608 .video_inputs = 2, 2609 /* .audio_inputs= 0, */ 2610 .svhs = 1, 2611 .muxsel = MUXSEL(2, 0, 1, 3), 2612 .tuner_type = TUNER_ABSENT, 2613 .tuner_addr = ADDR_UNSET, 2614 }, 2615 /* ---- card 0x94---------------------------------- */ 2616 [BTTV_BOARD_DVICO_FUSIONHDTV_2] = { 2617 .name = "DViCO FusionHDTV 2", 2618 .tuner_type = TUNER_PHILIPS_FCV1236D, 2619 .tuner_addr = ADDR_UNSET, 2620 .video_inputs = 3, 2621 /* .audio_inputs= 1, */ 2622 .svhs = 2, 2623 .muxsel = MUXSEL(2, 3, 1), 2624 .gpiomask = 0x00e00007, 2625 .gpiomux = { 0x00400005, 0, 0x00000001, 0 }, 2626 .gpiomute = 0x00c00007, 2627 .no_msp34xx = 1, 2628 .no_tda7432 = 1, 2629 }, 2630 /* ---- card 0x95---------------------------------- */ 2631 [BTTV_BOARD_TYPHOON_TVTUNERPCI] = { 2632 .name = "Typhoon TV-Tuner PCI (50684)", 2633 .video_inputs = 3, 2634 /* .audio_inputs= 1, */ 2635 .svhs = 2, 2636 .gpiomask = 0x3014f, 2637 .muxsel = MUXSEL(2, 3, 1, 1), 2638 .gpiomux = { 0x20001,0x10001, 0, 0 }, 2639 .gpiomute = 10, 2640 .pll = PLL_28, 2641 .tuner_type = TUNER_PHILIPS_PAL_I, 2642 .tuner_addr = ADDR_UNSET, 2643 }, 2644 [BTTV_BOARD_GEOVISION_GV600] = { 2645 /* emhn@usb.ve */ 2646 .name = "Geovision GV-600", 2647 .video_inputs = 16, 2648 /* .audio_inputs= 0, */ 2649 .svhs = NO_SVHS, 2650 .gpiomask = 0x0, 2651 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2), 2652 .muxsel_hook = geovision_muxsel, 2653 .gpiomux = { 0 }, 2654 .no_msp34xx = 1, 2655 .pll = PLL_28, 2656 .tuner_type = TUNER_ABSENT, 2657 .tuner_addr = ADDR_UNSET, 2658 }, 2659 [BTTV_BOARD_KOZUMI_KTV_01C] = { 2660 /* Mauro Lacy <mauro@lacy.com.ar> 2661 * Based on MagicTV and Conceptronic CONTVFMi */ 2662 2663 .name = "Kozumi KTV-01C", 2664 .video_inputs = 3, 2665 /* .audio_inputs= 1, */ 2666 .svhs = 2, 2667 .gpiomask = 0x008007, 2668 .muxsel = MUXSEL(2, 3, 1, 1), 2669 .gpiomux = { 0, 1, 2, 2 }, /* CONTVFMi */ 2670 .gpiomute = 3, /* CONTVFMi */ 2671 .tuner_type = TUNER_PHILIPS_FM1216ME_MK3, /* TCL MK3 */ 2672 .tuner_addr = ADDR_UNSET, 2673 .pll = PLL_28, 2674 .has_radio = 1, 2675 .has_remote = 1, 2676 }, 2677 [BTTV_BOARD_ENLTV_FM_2] = { 2678 /* Encore TV Tuner Pro ENL TV-FM-2 2679 Mauro Carvalho Chehab <mchehab@kernel.org> */ 2680 .name = "Encore ENL TV-FM-2", 2681 .video_inputs = 3, 2682 /* .audio_inputs= 1, */ 2683 .svhs = 2, 2684 /* bit 6 -> IR disabled 2685 bit 18/17 = 00 -> mute 2686 01 -> enable external audio input 2687 10 -> internal audio input (mono?) 2688 11 -> internal audio input 2689 */ 2690 .gpiomask = 0x060040, 2691 .muxsel = MUXSEL(2, 3, 3), 2692 .gpiomux = { 0x60000, 0x60000, 0x20000, 0x20000 }, 2693 .gpiomute = 0, 2694 .tuner_type = TUNER_TCL_MF02GIP_5N, 2695 .tuner_addr = ADDR_UNSET, 2696 .pll = PLL_28, 2697 .has_radio = 1, 2698 .has_remote = 1, 2699 }, 2700 [BTTV_BOARD_VD012] = { 2701 /* D.Heer@Phytec.de */ 2702 .name = "PHYTEC VD-012 (bt878)", 2703 .video_inputs = 4, 2704 /* .audio_inputs= 0, */ 2705 .svhs = NO_SVHS, 2706 .gpiomask = 0x00, 2707 .muxsel = MUXSEL(0, 2, 3, 1), 2708 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2709 .pll = PLL_28, 2710 .tuner_type = TUNER_ABSENT, 2711 .tuner_addr = ADDR_UNSET, 2712 }, 2713 [BTTV_BOARD_VD012_X1] = { 2714 /* D.Heer@Phytec.de */ 2715 .name = "PHYTEC VD-012-X1 (bt878)", 2716 .video_inputs = 4, 2717 /* .audio_inputs= 0, */ 2718 .svhs = 3, 2719 .gpiomask = 0x00, 2720 .muxsel = MUXSEL(2, 3, 1), 2721 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2722 .pll = PLL_28, 2723 .tuner_type = TUNER_ABSENT, 2724 .tuner_addr = ADDR_UNSET, 2725 }, 2726 [BTTV_BOARD_VD012_X2] = { 2727 /* D.Heer@Phytec.de */ 2728 .name = "PHYTEC VD-012-X2 (bt878)", 2729 .video_inputs = 4, 2730 /* .audio_inputs= 0, */ 2731 .svhs = 3, 2732 .gpiomask = 0x00, 2733 .muxsel = MUXSEL(3, 2, 1), 2734 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */ 2735 .pll = PLL_28, 2736 .tuner_type = TUNER_ABSENT, 2737 .tuner_addr = ADDR_UNSET, 2738 }, 2739 [BTTV_BOARD_GEOVISION_GV800S] = { 2740 /* Bruno Christo <bchristo@inf.ufsm.br> 2741 * 2742 * GeoVision GV-800(S) has 4 Conexant Fusion 878A: 2743 * 1 audio input per BT878A = 4 audio inputs 2744 * 4 video inputs per BT878A = 16 video inputs 2745 * This is the first BT878A chip of the GV-800(S). It's the 2746 * "master" chip and it controls the video inputs through an 2747 * analog multiplexer (a CD22M3494) via some GPIO pins. The 2748 * slaves should use card type 0x9e (following this one). 2749 * There is a EEPROM on the card which is currently not handled. 2750 * The audio input is not working yet. 2751 */ 2752 .name = "Geovision GV-800(S) (master)", 2753 .video_inputs = 4, 2754 /* .audio_inputs= 1, */ 2755 .tuner_type = TUNER_ABSENT, 2756 .tuner_addr = ADDR_UNSET, 2757 .svhs = NO_SVHS, 2758 .gpiomask = 0xf107f, 2759 .no_gpioirq = 1, 2760 .muxsel = MUXSEL(2, 2, 2, 2), 2761 .pll = PLL_28, 2762 .no_msp34xx = 1, 2763 .no_tda7432 = 1, 2764 .muxsel_hook = gv800s_muxsel, 2765 }, 2766 [BTTV_BOARD_GEOVISION_GV800S_SL] = { 2767 /* Bruno Christo <bchristo@inf.ufsm.br> 2768 * 2769 * GeoVision GV-800(S) has 4 Conexant Fusion 878A: 2770 * 1 audio input per BT878A = 4 audio inputs 2771 * 4 video inputs per BT878A = 16 video inputs 2772 * The 3 other BT878A chips are "slave" chips of the GV-800(S) 2773 * and should use this card type. 2774 * The audio input is not working yet. 2775 */ 2776 .name = "Geovision GV-800(S) (slave)", 2777 .video_inputs = 4, 2778 /* .audio_inputs= 1, */ 2779 .tuner_type = TUNER_ABSENT, 2780 .tuner_addr = ADDR_UNSET, 2781 .svhs = NO_SVHS, 2782 .gpiomask = 0x00, 2783 .no_gpioirq = 1, 2784 .muxsel = MUXSEL(2, 2, 2, 2), 2785 .pll = PLL_28, 2786 .no_msp34xx = 1, 2787 .no_tda7432 = 1, 2788 .muxsel_hook = gv800s_muxsel, 2789 }, 2790 [BTTV_BOARD_PV183] = { 2791 .name = "ProVideo PV183", /* 0x9f */ 2792 .video_inputs = 2, 2793 /* .audio_inputs= 0, */ 2794 .svhs = NO_SVHS, 2795 .gpiomask = 0, 2796 .muxsel = MUXSEL(2, 3), 2797 .gpiomux = { 0 }, 2798 .no_msp34xx = 1, 2799 .pll = PLL_28, 2800 .tuner_type = TUNER_ABSENT, 2801 .tuner_addr = ADDR_UNSET, 2802 }, 2803 /* ---- card 0xa0---------------------------------- */ 2804 [BTTV_BOARD_TVT_TD3116] = { 2805 .name = "Tongwei Video Technology TD-3116", 2806 .video_inputs = 16, 2807 .gpiomask = 0xc00ff, 2808 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2), 2809 .muxsel_hook = td3116_muxsel, 2810 .svhs = NO_SVHS, 2811 .pll = PLL_28, 2812 .tuner_type = TUNER_ABSENT, 2813 }, 2814 [BTTV_BOARD_APOSONIC_WDVR] = { 2815 .name = "Aposonic W-DVR", 2816 .video_inputs = 4, 2817 .svhs = NO_SVHS, 2818 .muxsel = MUXSEL(2, 3, 1, 0), 2819 .tuner_type = TUNER_ABSENT, 2820 }, 2821 [BTTV_BOARD_ADLINK_MPG24] = { 2822 /* Adlink MPG24 */ 2823 .name = "Adlink MPG24", 2824 .video_inputs = 1, 2825 /* .audio_inputs= 1, */ 2826 .svhs = NO_SVHS, 2827 .muxsel = MUXSEL(2, 2, 2, 2), 2828 .tuner_type = UNSET, 2829 .tuner_addr = ADDR_UNSET, 2830 .pll = PLL_28, 2831 }, 2832 [BTTV_BOARD_BT848_CAP_14] = { 2833 .name = "Bt848 Capture 14MHz", 2834 .video_inputs = 4, 2835 .svhs = 2, 2836 .muxsel = MUXSEL(2, 3, 1, 0), 2837 .pll = PLL_14, 2838 .tuner_type = TUNER_ABSENT, 2839 }, 2840 [BTTV_BOARD_CYBERVISION_CV06] = { 2841 .name = "CyberVision CV06 (SV)", 2842 .video_inputs = 4, 2843 /* .audio_inputs= 0, */ 2844 .svhs = NO_SVHS, 2845 .muxsel = MUXSEL(2, 3, 1, 0), 2846 .pll = PLL_28, 2847 .tuner_type = TUNER_ABSENT, 2848 .tuner_addr = ADDR_UNSET, 2849 }, 2850 [BTTV_BOARD_KWORLD_VSTREAM_XPERT] = { 2851 /* Pojar George <geoubuntu@gmail.com> */ 2852 .name = "Kworld V-Stream Xpert TV PVR878", 2853 .video_inputs = 3, 2854 /* .audio_inputs= 1, */ 2855 .svhs = 2, 2856 .gpiomask = 0x001c0007, 2857 .muxsel = MUXSEL(2, 3, 1, 1), 2858 .gpiomux = { 0, 1, 2, 2 }, 2859 .gpiomute = 3, 2860 .pll = PLL_28, 2861 .tuner_type = TUNER_TENA_9533_DI, 2862 .tuner_addr = ADDR_UNSET, 2863 .has_remote = 1, 2864 .has_radio = 1, 2865 }, 2866 /* ---- card 0xa6---------------------------------- */ 2867 [BTTV_BOARD_PCI_8604PW] = { 2868 /* PCI-8604PW with special unlock sequence */ 2869 .name = "PCI-8604PW", 2870 .video_inputs = 2, 2871 /* .audio_inputs= 0, */ 2872 .svhs = NO_SVHS, 2873 /* The second input is available on CN4, if populated. 2874 * The other 5x2 header (CN2?) connects to the same inputs 2875 * as the on-board BNCs */ 2876 .muxsel = MUXSEL(2, 3), 2877 .tuner_type = TUNER_ABSENT, 2878 .no_msp34xx = 1, 2879 .no_tda7432 = 1, 2880 .pll = PLL_35, 2881 }, 2882 }; 2883 2884 static const unsigned int bttv_num_tvcards = ARRAY_SIZE(bttv_tvcards); 2885 2886 /* ----------------------------------------------------------------------- */ 2887 2888 static unsigned char eeprom_data[256]; 2889 2890 /* 2891 * identify card 2892 */ 2893 void bttv_idcard(struct bttv *btv) 2894 { 2895 unsigned int gpiobits; 2896 int i,type; 2897 2898 /* read PCI subsystem ID */ 2899 btv->cardid = btv->c.pci->subsystem_device << 16; 2900 btv->cardid |= btv->c.pci->subsystem_vendor; 2901 2902 if (0 != btv->cardid && 0xffffffff != btv->cardid) { 2903 /* look for the card */ 2904 for (type = -1, i = 0; cards[i].id != 0; i++) 2905 if (cards[i].id == btv->cardid) 2906 type = i; 2907 2908 if (type != -1) { 2909 /* found it */ 2910 pr_info("%d: detected: %s [card=%d], PCI subsystem ID is %04x:%04x\n", 2911 btv->c.nr, cards[type].name, cards[type].cardnr, 2912 btv->cardid & 0xffff, 2913 (btv->cardid >> 16) & 0xffff); 2914 btv->c.type = cards[type].cardnr; 2915 } else { 2916 /* 404 */ 2917 pr_info("%d: subsystem: %04x:%04x (UNKNOWN)\n", 2918 btv->c.nr, btv->cardid & 0xffff, 2919 (btv->cardid >> 16) & 0xffff); 2920 pr_debug("please mail id, board name and the correct card= insmod option to linux-media@vger.kernel.org\n"); 2921 } 2922 } 2923 2924 /* let the user override the autodetected type */ 2925 if (card[btv->c.nr] < bttv_num_tvcards) 2926 btv->c.type=card[btv->c.nr]; 2927 2928 /* print which card config we are using */ 2929 pr_info("%d: using: %s [card=%d,%s]\n", 2930 btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type, 2931 card[btv->c.nr] < bttv_num_tvcards 2932 ? "insmod option" : "autodetected"); 2933 2934 /* overwrite gpio stuff ?? */ 2935 if (UNSET == audioall && UNSET == audiomux[0]) 2936 return; 2937 2938 if (UNSET != audiomux[0]) { 2939 gpiobits = 0; 2940 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) { 2941 bttv_tvcards[btv->c.type].gpiomux[i] = audiomux[i]; 2942 gpiobits |= audiomux[i]; 2943 } 2944 } else { 2945 gpiobits = audioall; 2946 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) { 2947 bttv_tvcards[btv->c.type].gpiomux[i] = audioall; 2948 } 2949 } 2950 bttv_tvcards[btv->c.type].gpiomask = (UNSET != gpiomask) ? gpiomask : gpiobits; 2951 pr_info("%d: gpio config override: mask=0x%x, mux=", 2952 btv->c.nr, bttv_tvcards[btv->c.type].gpiomask); 2953 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) { 2954 pr_cont("%s0x%x", 2955 i ? "," : "", bttv_tvcards[btv->c.type].gpiomux[i]); 2956 } 2957 pr_cont("\n"); 2958 } 2959 2960 /* 2961 * (most) board specific initialisations goes here 2962 */ 2963 2964 /* Some Modular Technology cards have an eeprom, but no subsystem ID */ 2965 static void identify_by_eeprom(struct bttv *btv, unsigned char eeprom_data[256]) 2966 { 2967 int type = -1; 2968 2969 if (0 == strncmp(eeprom_data,"GET MM20xPCTV",13)) 2970 type = BTTV_BOARD_MODTEC_205; 2971 else if (0 == strncmp(eeprom_data+20,"Picolo",7)) 2972 type = BTTV_BOARD_EURESYS_PICOLO; 2973 else if (eeprom_data[0] == 0x84 && eeprom_data[2]== 0) 2974 type = BTTV_BOARD_HAUPPAUGE; /* old bt848 */ 2975 2976 if (-1 != type) { 2977 btv->c.type = type; 2978 pr_info("%d: detected by eeprom: %s [card=%d]\n", 2979 btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type); 2980 } 2981 } 2982 2983 static void flyvideo_gpio(struct bttv *btv) 2984 { 2985 int gpio, has_remote, has_radio, is_capture_only; 2986 int is_lr90, has_tda9820_tda9821; 2987 int tuner_type = UNSET, ttype; 2988 2989 gpio_inout(0xffffff, 0); 2990 udelay(8); /* without this we would see the 0x1800 mask */ 2991 gpio = gpio_read(); 2992 /* FIXME: must restore OUR_EN ??? */ 2993 2994 /* all cards provide GPIO info, some have an additional eeprom 2995 * LR50: GPIO coding can be found lower right CP1 .. CP9 2996 * CP9=GPIO23 .. CP1=GPIO15; when OPEN, the corresponding GPIO reads 1. 2997 * GPIO14-12: n.c. 2998 * LR90: GP9=GPIO23 .. GP1=GPIO15 (right above the bt878) 2999 3000 * lowest 3 bytes are remote control codes (no handshake needed) 3001 * xxxFFF: No remote control chip soldered 3002 * xxxF00(LR26/LR50), xxxFE0(LR90): Remote control chip (LVA001 or CF45) soldered 3003 * Note: Some bits are Audio_Mask ! 3004 */ 3005 ttype = (gpio & 0x0f0000) >> 16; 3006 switch (ttype) { 3007 case 0x0: 3008 tuner_type = 2; /* NTSC, e.g. TPI8NSR11P */ 3009 break; 3010 case 0x2: 3011 tuner_type = 39; /* LG NTSC (newer TAPC series) TAPC-H701P */ 3012 break; 3013 case 0x4: 3014 tuner_type = 5; /* Philips PAL TPI8PSB02P, TPI8PSB12P, TPI8PSB12D or FI1216, FM1216 */ 3015 break; 3016 case 0x6: 3017 tuner_type = 37; /* LG PAL (newer TAPC series) TAPC-G702P */ 3018 break; 3019 case 0xC: 3020 tuner_type = 3; /* Philips SECAM(+PAL) FQ1216ME or FI1216MF */ 3021 break; 3022 default: 3023 pr_info("%d: FlyVideo_gpio: unknown tuner type\n", btv->c.nr); 3024 break; 3025 } 3026 3027 has_remote = gpio & 0x800000; 3028 has_radio = gpio & 0x400000; 3029 /* unknown 0x200000; 3030 * unknown2 0x100000; */ 3031 is_capture_only = !(gpio & 0x008000); /* GPIO15 */ 3032 has_tda9820_tda9821 = !(gpio & 0x004000); 3033 is_lr90 = !(gpio & 0x002000); /* else LR26/LR50 (LR38/LR51 f. capture only) */ 3034 /* 3035 * gpio & 0x001000 output bit for audio routing */ 3036 3037 if (is_capture_only) 3038 tuner_type = TUNER_ABSENT; /* No tuner present */ 3039 3040 pr_info("%d: FlyVideo Radio=%s RemoteControl=%s Tuner=%d gpio=0x%06x\n", 3041 btv->c.nr, has_radio ? "yes" : "no", 3042 has_remote ? "yes" : "no", tuner_type, gpio); 3043 pr_info("%d: FlyVideo LR90=%s tda9821/tda9820=%s capture_only=%s\n", 3044 btv->c.nr, is_lr90 ? "yes" : "no", 3045 has_tda9820_tda9821 ? "yes" : "no", 3046 is_capture_only ? "yes" : "no"); 3047 3048 if (tuner_type != UNSET) /* only set if known tuner autodetected, else let insmod option through */ 3049 btv->tuner_type = tuner_type; 3050 btv->has_radio = has_radio; 3051 3052 /* LR90 Audio Routing is done by 2 hef4052, so Audio_Mask has 4 bits: 0x001c80 3053 * LR26/LR50 only has 1 hef4052, Audio_Mask 0x000c00 3054 * Audio options: from tuner, from tda9821/tda9821(mono,stereo,sap), from tda9874, ext., mute */ 3055 if (has_tda9820_tda9821) 3056 btv->audio_mode_gpio = lt9415_audio; 3057 /* todo: if(has_tda9874) btv->audio_mode_gpio = fv2000s_audio; */ 3058 } 3059 3060 static int miro_tunermap[] = { 0,6,2,3, 4,5,6,0, 3,0,4,5, 5,2,16,1, 3061 14,2,17,1, 4,1,4,3, 1,2,16,1, 4,4,4,4 }; 3062 static int miro_fmtuner[] = { 0,0,0,0, 0,0,0,0, 0,0,0,0, 0,0,0,1, 3063 1,1,1,1, 1,1,1,0, 0,0,0,0, 0,1,0,0 }; 3064 3065 static void miro_pinnacle_gpio(struct bttv *btv) 3066 { 3067 int id,msp,gpio; 3068 char *info; 3069 3070 gpio_inout(0xffffff, 0); 3071 gpio = gpio_read(); 3072 id = ((gpio>>10) & 63) -1; 3073 msp = bttv_I2CRead(btv, I2C_ADDR_MSP3400, "MSP34xx"); 3074 if (id < 32) { 3075 btv->tuner_type = miro_tunermap[id]; 3076 if (0 == (gpio & 0x20)) { 3077 btv->has_radio = 1; 3078 if (!miro_fmtuner[id]) { 3079 btv->has_tea575x = 1; 3080 btv->tea_gpio.wren = 6; 3081 btv->tea_gpio.most = 7; 3082 btv->tea_gpio.clk = 8; 3083 btv->tea_gpio.data = 9; 3084 tea575x_init(btv); 3085 } 3086 } else { 3087 btv->has_radio = 0; 3088 } 3089 if (-1 != msp) { 3090 if (btv->c.type == BTTV_BOARD_MIRO) 3091 btv->c.type = BTTV_BOARD_MIROPRO; 3092 if (btv->c.type == BTTV_BOARD_PINNACLE) 3093 btv->c.type = BTTV_BOARD_PINNACLEPRO; 3094 } 3095 pr_info("%d: miro: id=%d tuner=%d radio=%s stereo=%s\n", 3096 btv->c.nr, id+1, btv->tuner_type, 3097 !btv->has_radio ? "no" : 3098 (btv->has_tea575x ? "tea575x" : "fmtuner"), 3099 (-1 == msp) ? "no" : "yes"); 3100 } else { 3101 /* new cards with microtune tuner */ 3102 id = 63 - id; 3103 btv->has_radio = 0; 3104 switch (id) { 3105 case 1: 3106 info = "PAL / mono"; 3107 btv->tda9887_conf = TDA9887_INTERCARRIER; 3108 break; 3109 case 2: 3110 info = "PAL+SECAM / stereo"; 3111 btv->has_radio = 1; 3112 btv->tda9887_conf = TDA9887_QSS; 3113 break; 3114 case 3: 3115 info = "NTSC / stereo"; 3116 btv->has_radio = 1; 3117 btv->tda9887_conf = TDA9887_QSS; 3118 break; 3119 case 4: 3120 info = "PAL+SECAM / mono"; 3121 btv->tda9887_conf = TDA9887_QSS; 3122 break; 3123 case 5: 3124 info = "NTSC / mono"; 3125 btv->tda9887_conf = TDA9887_INTERCARRIER; 3126 break; 3127 case 6: 3128 info = "NTSC / stereo"; 3129 btv->tda9887_conf = TDA9887_INTERCARRIER; 3130 break; 3131 case 7: 3132 info = "PAL / stereo"; 3133 btv->tda9887_conf = TDA9887_INTERCARRIER; 3134 break; 3135 default: 3136 info = "oops: unknown card"; 3137 break; 3138 } 3139 if (-1 != msp) 3140 btv->c.type = BTTV_BOARD_PINNACLEPRO; 3141 pr_info("%d: pinnacle/mt: id=%d info=\"%s\" radio=%s\n", 3142 btv->c.nr, id, info, btv->has_radio ? "yes" : "no"); 3143 btv->tuner_type = TUNER_MT2032; 3144 } 3145 } 3146 3147 /* GPIO21 L: Buffer aktiv, H: Buffer inaktiv */ 3148 #define LM1882_SYNC_DRIVE 0x200000L 3149 3150 static void init_ids_eagle(struct bttv *btv) 3151 { 3152 gpio_inout(0xffffff,0xFFFF37); 3153 gpio_write(0x200020); 3154 3155 /* flash strobe inverter ?! */ 3156 gpio_write(0x200024); 3157 3158 /* switch sync drive off */ 3159 gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE); 3160 3161 /* set BT848 muxel to 2 */ 3162 btaor((2)<<5, ~(2<<5), BT848_IFORM); 3163 } 3164 3165 /* Muxsel helper for the IDS Eagle. 3166 * the eagles does not use the standard muxsel-bits but 3167 * has its own multiplexer */ 3168 static void eagle_muxsel(struct bttv *btv, unsigned int input) 3169 { 3170 gpio_bits(3, input & 3); 3171 3172 /* composite */ 3173 /* set chroma ADC to sleep */ 3174 btor(BT848_ADC_C_SLEEP, BT848_ADC); 3175 /* set to composite video */ 3176 btand(~BT848_CONTROL_COMP, BT848_E_CONTROL); 3177 btand(~BT848_CONTROL_COMP, BT848_O_CONTROL); 3178 3179 /* switch sync drive off */ 3180 gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE); 3181 } 3182 3183 static void gvc1100_muxsel(struct bttv *btv, unsigned int input) 3184 { 3185 static const int masks[] = {0x30, 0x01, 0x12, 0x23}; 3186 gpio_write(masks[input%4]); 3187 } 3188 3189 /* LMLBT4x initialization - to allow access to GPIO bits for sensors input and 3190 alarms output 3191 3192 GPIObit | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | 3193 assignment | TI | O3|INx| O2| O1|IN4|IN3|IN2|IN1| | | 3194 3195 IN - sensor inputs, INx - sensor inputs and TI XORed together 3196 O1,O2,O3 - alarm outputs (relays) 3197 3198 OUT ENABLE 1 1 0 . 1 1 0 0 . 0 0 0 0 = 0x6C0 3199 3200 */ 3201 3202 static void init_lmlbt4x(struct bttv *btv) 3203 { 3204 pr_debug("LMLBT4x init\n"); 3205 btwrite(0x000000, BT848_GPIO_REG_INP); 3206 gpio_inout(0xffffff, 0x0006C0); 3207 gpio_write(0x000000); 3208 } 3209 3210 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input) 3211 { 3212 unsigned int inmux = input % 8; 3213 gpio_inout( 0xf, 0xf ); 3214 gpio_bits( 0xf, inmux ); 3215 } 3216 3217 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input) 3218 { 3219 unsigned int inmux = input % 4; 3220 gpio_inout( 3<<9, 3<<9 ); 3221 gpio_bits( 3<<9, inmux<<9 ); 3222 } 3223 3224 static void geovision_muxsel(struct bttv *btv, unsigned int input) 3225 { 3226 unsigned int inmux = input % 16; 3227 gpio_inout(0xf, 0xf); 3228 gpio_bits(0xf, inmux); 3229 } 3230 3231 /* 3232 * The TD3116 has 2 74HC4051 muxes wired to the MUX0 input of a bt878. 3233 * The first 74HC4051 has the lower 8 inputs, the second one the higher 8. 3234 * The muxes are controlled via a 74HC373 latch which is connected to 3235 * GPIOs 0-7. GPIO 18 is connected to the LE signal of the latch. 3236 * Q0 of the latch is connected to the Enable (~E) input of the first 3237 * 74HC4051. Q1 - Q3 are connected to S0 - S2 of the same 74HC4051. 3238 * Q4 - Q7 are connected to the second 74HC4051 in the same way. 3239 */ 3240 3241 static void td3116_latch_value(struct bttv *btv, u32 value) 3242 { 3243 gpio_bits((1<<18) | 0xff, value); 3244 gpio_bits((1<<18) | 0xff, (1<<18) | value); 3245 udelay(1); 3246 gpio_bits((1<<18) | 0xff, value); 3247 } 3248 3249 static void td3116_muxsel(struct bttv *btv, unsigned int input) 3250 { 3251 u32 value; 3252 u32 highbit; 3253 3254 highbit = (input & 0x8) >> 3 ; 3255 3256 /* Disable outputs and set value in the mux */ 3257 value = 0x11; /* Disable outputs */ 3258 value |= ((input & 0x7) << 1) << (4 * highbit); 3259 td3116_latch_value(btv, value); 3260 3261 /* Enable the correct output */ 3262 value &= ~0x11; 3263 value |= ((highbit ^ 0x1) << 4) | highbit; 3264 td3116_latch_value(btv, value); 3265 } 3266 3267 /* ----------------------------------------------------------------------- */ 3268 3269 static void bttv_reset_audio(struct bttv *btv) 3270 { 3271 /* 3272 * BT878A has a audio-reset register. 3273 * 1. This register is an audio reset function but it is in 3274 * function-0 (video capture) address space. 3275 * 2. It is enough to do this once per power-up of the card. 3276 * 3. There is a typo in the Conexant doc -- it is not at 3277 * 0x5B, but at 0x058. (B is an odd-number, obviously a typo!). 3278 * --//Shrikumar 030609 3279 */ 3280 if (btv->id != 878) 3281 return; 3282 3283 if (bttv_debug) 3284 pr_debug("%d: BT878A ARESET\n", btv->c.nr); 3285 btwrite((1<<7), 0x058); 3286 udelay(10); 3287 btwrite( 0, 0x058); 3288 } 3289 3290 /* initialization part one -- before registering i2c bus */ 3291 void bttv_init_card1(struct bttv *btv) 3292 { 3293 switch (btv->c.type) { 3294 case BTTV_BOARD_HAUPPAUGE: 3295 case BTTV_BOARD_HAUPPAUGE878: 3296 boot_msp34xx(btv,5); 3297 break; 3298 case BTTV_BOARD_VOODOOTV_200: 3299 case BTTV_BOARD_VOODOOTV_FM: 3300 boot_msp34xx(btv,20); 3301 break; 3302 case BTTV_BOARD_AVERMEDIA98: 3303 boot_msp34xx(btv,11); 3304 break; 3305 case BTTV_BOARD_HAUPPAUGEPVR: 3306 pvr_boot(btv); 3307 break; 3308 case BTTV_BOARD_TWINHAN_DST: 3309 case BTTV_BOARD_AVDVBT_771: 3310 case BTTV_BOARD_PINNACLESAT: 3311 btv->use_i2c_hw = 1; 3312 break; 3313 case BTTV_BOARD_ADLINK_RTV24: 3314 init_RTV24( btv ); 3315 break; 3316 case BTTV_BOARD_PCI_8604PW: 3317 init_PCI8604PW(btv); 3318 break; 3319 3320 } 3321 if (!bttv_tvcards[btv->c.type].has_dvb) 3322 bttv_reset_audio(btv); 3323 } 3324 3325 /* initialization part two -- after registering i2c bus */ 3326 void bttv_init_card2(struct bttv *btv) 3327 { 3328 btv->tuner_type = UNSET; 3329 3330 if (BTTV_BOARD_UNKNOWN == btv->c.type) { 3331 bttv_readee(btv,eeprom_data,0xa0); 3332 identify_by_eeprom(btv,eeprom_data); 3333 } 3334 3335 switch (btv->c.type) { 3336 case BTTV_BOARD_MIRO: 3337 case BTTV_BOARD_MIROPRO: 3338 case BTTV_BOARD_PINNACLE: 3339 case BTTV_BOARD_PINNACLEPRO: 3340 /* miro/pinnacle */ 3341 miro_pinnacle_gpio(btv); 3342 break; 3343 case BTTV_BOARD_FLYVIDEO_98: 3344 case BTTV_BOARD_MAXI: 3345 case BTTV_BOARD_LIFE_FLYKIT: 3346 case BTTV_BOARD_FLYVIDEO: 3347 case BTTV_BOARD_TYPHOON_TVIEW: 3348 case BTTV_BOARD_CHRONOS_VS2: 3349 case BTTV_BOARD_FLYVIDEO_98FM: 3350 case BTTV_BOARD_FLYVIDEO2000: 3351 case BTTV_BOARD_FLYVIDEO98EZ: 3352 case BTTV_BOARD_CONFERENCETV: 3353 case BTTV_BOARD_LIFETEC_9415: 3354 flyvideo_gpio(btv); 3355 break; 3356 case BTTV_BOARD_HAUPPAUGE: 3357 case BTTV_BOARD_HAUPPAUGE878: 3358 case BTTV_BOARD_HAUPPAUGEPVR: 3359 /* pick up some config infos from the eeprom */ 3360 bttv_readee(btv,eeprom_data,0xa0); 3361 hauppauge_eeprom(btv); 3362 break; 3363 case BTTV_BOARD_AVERMEDIA98: 3364 case BTTV_BOARD_AVPHONE98: 3365 bttv_readee(btv,eeprom_data,0xa0); 3366 avermedia_eeprom(btv); 3367 break; 3368 case BTTV_BOARD_PXC200: 3369 init_PXC200(btv); 3370 break; 3371 case BTTV_BOARD_PICOLO_TETRA_CHIP: 3372 picolo_tetra_init(btv); 3373 break; 3374 case BTTV_BOARD_VHX: 3375 btv->has_radio = 1; 3376 btv->has_tea575x = 1; 3377 btv->tea_gpio.wren = 5; 3378 btv->tea_gpio.most = 6; 3379 btv->tea_gpio.clk = 3; 3380 btv->tea_gpio.data = 4; 3381 tea575x_init(btv); 3382 break; 3383 case BTTV_BOARD_VOBIS_BOOSTAR: 3384 case BTTV_BOARD_TERRATV: 3385 terratec_active_radio_upgrade(btv); 3386 break; 3387 case BTTV_BOARD_MAGICTVIEW061: 3388 if (btv->cardid == 0x3002144f) { 3389 btv->has_radio=1; 3390 pr_info("%d: radio detected by subsystem id (CPH05x)\n", 3391 btv->c.nr); 3392 } 3393 break; 3394 case BTTV_BOARD_STB2: 3395 if (btv->cardid == 0x3060121a) { 3396 /* Fix up entry for 3DFX VoodooTV 100, 3397 which is an OEM STB card variant. */ 3398 btv->has_radio=0; 3399 btv->tuner_type=TUNER_TEMIC_NTSC; 3400 } 3401 break; 3402 case BTTV_BOARD_OSPREY1x0: 3403 case BTTV_BOARD_OSPREY1x0_848: 3404 case BTTV_BOARD_OSPREY101_848: 3405 case BTTV_BOARD_OSPREY1x1: 3406 case BTTV_BOARD_OSPREY1x1_SVID: 3407 case BTTV_BOARD_OSPREY2xx: 3408 case BTTV_BOARD_OSPREY2x0_SVID: 3409 case BTTV_BOARD_OSPREY2x0: 3410 case BTTV_BOARD_OSPREY440: 3411 case BTTV_BOARD_OSPREY500: 3412 case BTTV_BOARD_OSPREY540: 3413 case BTTV_BOARD_OSPREY2000: 3414 bttv_readee(btv,eeprom_data,0xa0); 3415 osprey_eeprom(btv, eeprom_data); 3416 break; 3417 case BTTV_BOARD_IDS_EAGLE: 3418 init_ids_eagle(btv); 3419 break; 3420 case BTTV_BOARD_MODTEC_205: 3421 bttv_readee(btv,eeprom_data,0xa0); 3422 modtec_eeprom(btv); 3423 break; 3424 case BTTV_BOARD_LMLBT4: 3425 init_lmlbt4x(btv); 3426 break; 3427 case BTTV_BOARD_TIBET_CS16: 3428 tibetCS16_init(btv); 3429 break; 3430 case BTTV_BOARD_KODICOM_4400R: 3431 kodicom4400r_init(btv); 3432 break; 3433 case BTTV_BOARD_GEOVISION_GV800S: 3434 gv800s_init(btv); 3435 break; 3436 } 3437 3438 /* pll configuration */ 3439 if (!(btv->id==848 && btv->revision==0x11)) { 3440 /* defaults from card list */ 3441 if (PLL_28 == bttv_tvcards[btv->c.type].pll) { 3442 btv->pll.pll_ifreq=28636363; 3443 btv->pll.pll_crystal=BT848_IFORM_XT0; 3444 } 3445 if (PLL_35 == bttv_tvcards[btv->c.type].pll) { 3446 btv->pll.pll_ifreq=35468950; 3447 btv->pll.pll_crystal=BT848_IFORM_XT1; 3448 } 3449 if (PLL_14 == bttv_tvcards[btv->c.type].pll) { 3450 btv->pll.pll_ifreq = 14318181; 3451 btv->pll.pll_crystal = BT848_IFORM_XT0; 3452 } 3453 /* insmod options can override */ 3454 switch (pll[btv->c.nr]) { 3455 case 0: /* none */ 3456 btv->pll.pll_crystal = 0; 3457 btv->pll.pll_ifreq = 0; 3458 btv->pll.pll_ofreq = 0; 3459 break; 3460 case 1: /* 28 MHz */ 3461 case 28: 3462 btv->pll.pll_ifreq = 28636363; 3463 btv->pll.pll_ofreq = 0; 3464 btv->pll.pll_crystal = BT848_IFORM_XT0; 3465 break; 3466 case 2: /* 35 MHz */ 3467 case 35: 3468 btv->pll.pll_ifreq = 35468950; 3469 btv->pll.pll_ofreq = 0; 3470 btv->pll.pll_crystal = BT848_IFORM_XT1; 3471 break; 3472 case 3: /* 14 MHz */ 3473 case 14: 3474 btv->pll.pll_ifreq = 14318181; 3475 btv->pll.pll_ofreq = 0; 3476 btv->pll.pll_crystal = BT848_IFORM_XT0; 3477 break; 3478 } 3479 } 3480 btv->pll.pll_current = -1; 3481 3482 /* tuner configuration (from card list / autodetect / insmod option) */ 3483 if (UNSET != bttv_tvcards[btv->c.type].tuner_type) 3484 if (UNSET == btv->tuner_type) 3485 btv->tuner_type = bttv_tvcards[btv->c.type].tuner_type; 3486 if (UNSET != tuner[btv->c.nr]) 3487 btv->tuner_type = tuner[btv->c.nr]; 3488 3489 if (btv->tuner_type == TUNER_ABSENT) 3490 pr_info("%d: tuner absent\n", btv->c.nr); 3491 else if (btv->tuner_type == UNSET) 3492 pr_warn("%d: tuner type unset\n", btv->c.nr); 3493 else 3494 pr_info("%d: tuner type=%d\n", btv->c.nr, btv->tuner_type); 3495 3496 if (autoload != UNSET) { 3497 pr_warn("%d: the autoload option is obsolete\n", btv->c.nr); 3498 pr_warn("%d: use option msp3400, tda7432 or tvaudio to override which audio module should be used\n", 3499 btv->c.nr); 3500 } 3501 3502 if (UNSET == btv->tuner_type) 3503 btv->tuner_type = TUNER_ABSENT; 3504 3505 btv->dig = bttv_tvcards[btv->c.type].has_dig_in ? 3506 bttv_tvcards[btv->c.type].video_inputs - 1 : UNSET; 3507 btv->svhs = bttv_tvcards[btv->c.type].svhs == NO_SVHS ? 3508 UNSET : bttv_tvcards[btv->c.type].svhs; 3509 if (svhs[btv->c.nr] != UNSET) 3510 btv->svhs = svhs[btv->c.nr]; 3511 if (remote[btv->c.nr] != UNSET) 3512 btv->has_remote = remote[btv->c.nr]; 3513 3514 if (bttv_tvcards[btv->c.type].has_radio) 3515 btv->has_radio = 1; 3516 if (bttv_tvcards[btv->c.type].has_remote) 3517 btv->has_remote = 1; 3518 if (!bttv_tvcards[btv->c.type].no_gpioirq) 3519 btv->gpioirq = 1; 3520 if (bttv_tvcards[btv->c.type].volume_gpio) 3521 btv->volume_gpio = bttv_tvcards[btv->c.type].volume_gpio; 3522 if (bttv_tvcards[btv->c.type].audio_mode_gpio) 3523 btv->audio_mode_gpio = bttv_tvcards[btv->c.type].audio_mode_gpio; 3524 3525 if (btv->tuner_type == TUNER_ABSENT) 3526 return; /* no tuner or related drivers to load */ 3527 3528 if (btv->has_saa6588 || saa6588[btv->c.nr]) { 3529 /* Probe for RDS receiver chip */ 3530 static const unsigned short addrs[] = { 3531 0x20 >> 1, 3532 0x22 >> 1, 3533 I2C_CLIENT_END 3534 }; 3535 struct v4l2_subdev *sd; 3536 3537 sd = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3538 &btv->c.i2c_adap, "saa6588", 0, addrs); 3539 btv->has_saa6588 = (sd != NULL); 3540 } 3541 3542 /* try to detect audio/fader chips */ 3543 3544 /* First check if the user specified the audio chip via a module 3545 option. */ 3546 3547 switch (audiodev[btv->c.nr]) { 3548 case -1: 3549 return; /* do not load any audio module */ 3550 3551 case 0: /* autodetect */ 3552 break; 3553 3554 case 1: { 3555 /* The user specified that we should probe for msp3400 */ 3556 static const unsigned short addrs[] = { 3557 I2C_ADDR_MSP3400 >> 1, 3558 I2C_ADDR_MSP3400_ALT >> 1, 3559 I2C_CLIENT_END 3560 }; 3561 3562 btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3563 &btv->c.i2c_adap, "msp3400", 0, addrs); 3564 if (btv->sd_msp34xx) 3565 return; 3566 goto no_audio; 3567 } 3568 3569 case 2: { 3570 /* The user specified that we should probe for tda7432 */ 3571 static const unsigned short addrs[] = { 3572 I2C_ADDR_TDA7432 >> 1, 3573 I2C_CLIENT_END 3574 }; 3575 3576 if (v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3577 &btv->c.i2c_adap, "tda7432", 0, addrs)) 3578 return; 3579 goto no_audio; 3580 } 3581 3582 case 3: { 3583 /* The user specified that we should probe for tvaudio */ 3584 btv->sd_tvaudio = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3585 &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs()); 3586 if (btv->sd_tvaudio) 3587 return; 3588 goto no_audio; 3589 } 3590 3591 default: 3592 pr_warn("%d: unknown audiodev value!\n", btv->c.nr); 3593 return; 3594 } 3595 3596 /* There were no overrides, so now we try to discover this through the 3597 card definition */ 3598 3599 /* probe for msp3400 first: this driver can detect whether or not 3600 it really is a msp3400, so it will return NULL when the device 3601 found is really something else (e.g. a tea6300). */ 3602 if (!bttv_tvcards[btv->c.type].no_msp34xx) { 3603 btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3604 &btv->c.i2c_adap, "msp3400", 3605 0, I2C_ADDRS(I2C_ADDR_MSP3400 >> 1)); 3606 } else if (bttv_tvcards[btv->c.type].msp34xx_alt) { 3607 btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3608 &btv->c.i2c_adap, "msp3400", 3609 0, I2C_ADDRS(I2C_ADDR_MSP3400_ALT >> 1)); 3610 } 3611 3612 /* If we found a msp34xx, then we're done. */ 3613 if (btv->sd_msp34xx) 3614 return; 3615 3616 /* Now see if we can find one of the tvaudio devices. */ 3617 btv->sd_tvaudio = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3618 &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs()); 3619 if (btv->sd_tvaudio) { 3620 /* There may be two tvaudio chips on the card, so try to 3621 find another. */ 3622 v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3623 &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs()); 3624 } 3625 3626 /* it might also be a tda7432. */ 3627 if (!bttv_tvcards[btv->c.type].no_tda7432) { 3628 static const unsigned short addrs[] = { 3629 I2C_ADDR_TDA7432 >> 1, 3630 I2C_CLIENT_END 3631 }; 3632 3633 btv->sd_tda7432 = v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3634 &btv->c.i2c_adap, "tda7432", 0, addrs); 3635 if (btv->sd_tda7432) 3636 return; 3637 } 3638 if (btv->sd_tvaudio) 3639 return; 3640 3641 no_audio: 3642 pr_warn("%d: audio absent, no audio device found!\n", btv->c.nr); 3643 } 3644 3645 3646 /* initialize the tuner */ 3647 void bttv_init_tuner(struct bttv *btv) 3648 { 3649 int addr = ADDR_UNSET; 3650 3651 if (ADDR_UNSET != bttv_tvcards[btv->c.type].tuner_addr) 3652 addr = bttv_tvcards[btv->c.type].tuner_addr; 3653 3654 if (btv->tuner_type != TUNER_ABSENT) { 3655 struct tuner_setup tun_setup; 3656 3657 /* Load tuner module before issuing tuner config call! */ 3658 if (btv->has_radio) 3659 v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3660 &btv->c.i2c_adap, "tuner", 3661 0, v4l2_i2c_tuner_addrs(ADDRS_RADIO)); 3662 v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3663 &btv->c.i2c_adap, "tuner", 3664 0, v4l2_i2c_tuner_addrs(ADDRS_DEMOD)); 3665 v4l2_i2c_new_subdev(&btv->c.v4l2_dev, 3666 &btv->c.i2c_adap, "tuner", 3667 0, v4l2_i2c_tuner_addrs(ADDRS_TV_WITH_DEMOD)); 3668 3669 tun_setup.mode_mask = T_ANALOG_TV; 3670 tun_setup.type = btv->tuner_type; 3671 tun_setup.addr = addr; 3672 3673 if (btv->has_radio) 3674 tun_setup.mode_mask |= T_RADIO; 3675 3676 bttv_call_all(btv, tuner, s_type_addr, &tun_setup); 3677 } 3678 3679 if (btv->tda9887_conf) { 3680 struct v4l2_priv_tun_config tda9887_cfg; 3681 3682 tda9887_cfg.tuner = TUNER_TDA9887; 3683 tda9887_cfg.priv = &btv->tda9887_conf; 3684 3685 bttv_call_all(btv, tuner, s_config, &tda9887_cfg); 3686 } 3687 } 3688 3689 /* ----------------------------------------------------------------------- */ 3690 3691 static void modtec_eeprom(struct bttv *btv) 3692 { 3693 if( strncmp(&(eeprom_data[0x1e]),"Temic 4066 FY5",14) ==0) { 3694 btv->tuner_type=TUNER_TEMIC_4066FY5_PAL_I; 3695 pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n", 3696 btv->c.nr, &eeprom_data[0x1e]); 3697 } else if (strncmp(&(eeprom_data[0x1e]),"Alps TSBB5",10) ==0) { 3698 btv->tuner_type=TUNER_ALPS_TSBB5_PAL_I; 3699 pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n", 3700 btv->c.nr, &eeprom_data[0x1e]); 3701 } else if (strncmp(&(eeprom_data[0x1e]),"Philips FM1246",14) ==0) { 3702 btv->tuner_type=TUNER_PHILIPS_NTSC; 3703 pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n", 3704 btv->c.nr, &eeprom_data[0x1e]); 3705 } else { 3706 pr_info("%d: Modtec: Unknown TunerString: %s\n", 3707 btv->c.nr, &eeprom_data[0x1e]); 3708 } 3709 } 3710 3711 static void hauppauge_eeprom(struct bttv *btv) 3712 { 3713 struct tveeprom tv; 3714 3715 tveeprom_hauppauge_analog(&tv, eeprom_data); 3716 btv->tuner_type = tv.tuner_type; 3717 btv->has_radio = tv.has_radio; 3718 3719 pr_info("%d: Hauppauge eeprom indicates model#%d\n", 3720 btv->c.nr, tv.model); 3721 3722 /* 3723 * Some of the 878 boards have duplicate PCI IDs. Switch the board 3724 * type based on model #. 3725 */ 3726 if(tv.model == 64900) { 3727 pr_info("%d: Switching board type from %s to %s\n", 3728 btv->c.nr, 3729 bttv_tvcards[btv->c.type].name, 3730 bttv_tvcards[BTTV_BOARD_HAUPPAUGE_IMPACTVCB].name); 3731 btv->c.type = BTTV_BOARD_HAUPPAUGE_IMPACTVCB; 3732 } 3733 3734 /* The 61334 needs the msp3410 to do the radio demod to get sound */ 3735 if (tv.model == 61334) 3736 btv->radio_uses_msp_demodulator = 1; 3737 } 3738 3739 /* ----------------------------------------------------------------------- */ 3740 3741 static void bttv_tea575x_set_pins(struct snd_tea575x *tea, u8 pins) 3742 { 3743 struct bttv *btv = tea->private_data; 3744 struct bttv_tea575x_gpio gpio = btv->tea_gpio; 3745 u16 val = 0; 3746 3747 val |= (pins & TEA575X_DATA) ? (1 << gpio.data) : 0; 3748 val |= (pins & TEA575X_CLK) ? (1 << gpio.clk) : 0; 3749 val |= (pins & TEA575X_WREN) ? (1 << gpio.wren) : 0; 3750 3751 gpio_bits((1 << gpio.data) | (1 << gpio.clk) | (1 << gpio.wren), val); 3752 if (btv->mbox_ior) { 3753 /* IOW and CSEL active */ 3754 gpio_bits(btv->mbox_iow | btv->mbox_csel, 0); 3755 udelay(5); 3756 /* all inactive */ 3757 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel, 3758 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel); 3759 } 3760 } 3761 3762 static u8 bttv_tea575x_get_pins(struct snd_tea575x *tea) 3763 { 3764 struct bttv *btv = tea->private_data; 3765 struct bttv_tea575x_gpio gpio = btv->tea_gpio; 3766 u8 ret = 0; 3767 u16 val; 3768 3769 if (btv->mbox_ior) { 3770 /* IOR and CSEL active */ 3771 gpio_bits(btv->mbox_ior | btv->mbox_csel, 0); 3772 udelay(5); 3773 } 3774 val = gpio_read(); 3775 if (btv->mbox_ior) { 3776 /* all inactive */ 3777 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel, 3778 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel); 3779 } 3780 3781 if (val & (1 << gpio.data)) 3782 ret |= TEA575X_DATA; 3783 if (val & (1 << gpio.most)) 3784 ret |= TEA575X_MOST; 3785 3786 return ret; 3787 } 3788 3789 static void bttv_tea575x_set_direction(struct snd_tea575x *tea, bool output) 3790 { 3791 struct bttv *btv = tea->private_data; 3792 struct bttv_tea575x_gpio gpio = btv->tea_gpio; 3793 u32 mask = (1 << gpio.clk) | (1 << gpio.wren) | (1 << gpio.data) | 3794 (1 << gpio.most); 3795 3796 if (output) 3797 gpio_inout(mask, (1 << gpio.data) | (1 << gpio.clk) | 3798 (1 << gpio.wren)); 3799 else 3800 gpio_inout(mask, (1 << gpio.clk) | (1 << gpio.wren)); 3801 } 3802 3803 static const struct snd_tea575x_ops bttv_tea_ops = { 3804 .set_pins = bttv_tea575x_set_pins, 3805 .get_pins = bttv_tea575x_get_pins, 3806 .set_direction = bttv_tea575x_set_direction, 3807 }; 3808 3809 static int tea575x_init(struct bttv *btv) 3810 { 3811 btv->tea.private_data = btv; 3812 btv->tea.ops = &bttv_tea_ops; 3813 if (!snd_tea575x_hw_init(&btv->tea)) { 3814 pr_info("%d: detected TEA575x radio\n", btv->c.nr); 3815 btv->tea.mute = false; 3816 return 0; 3817 } 3818 3819 btv->has_tea575x = 0; 3820 btv->has_radio = 0; 3821 3822 return -ENODEV; 3823 } 3824 3825 /* ----------------------------------------------------------------------- */ 3826 3827 static int terratec_active_radio_upgrade(struct bttv *btv) 3828 { 3829 btv->has_radio = 1; 3830 btv->has_tea575x = 1; 3831 btv->tea_gpio.wren = 4; 3832 btv->tea_gpio.most = 5; 3833 btv->tea_gpio.clk = 3; 3834 btv->tea_gpio.data = 2; 3835 3836 btv->mbox_iow = 1 << 8; 3837 btv->mbox_ior = 1 << 9; 3838 btv->mbox_csel = 1 << 10; 3839 3840 if (!tea575x_init(btv)) { 3841 pr_info("%d: Terratec Active Radio Upgrade found\n", btv->c.nr); 3842 btv->has_saa6588 = 1; 3843 } 3844 3845 return 0; 3846 } 3847 3848 3849 /* ----------------------------------------------------------------------- */ 3850 3851 /* 3852 * minimal bootstrap for the WinTV/PVR -- upload altera firmware. 3853 * 3854 * The hcwamc.rbf firmware file is on the Hauppauge driver CD. Have 3855 * a look at Pvr/pvr45xxx.EXE (self-extracting zip archive, can be 3856 * unpacked with unzip). 3857 */ 3858 #define PVR_GPIO_DELAY 10 3859 3860 #define BTTV_ALT_DATA 0x000001 3861 #define BTTV_ALT_DCLK 0x100000 3862 #define BTTV_ALT_NCONFIG 0x800000 3863 3864 static int pvr_altera_load(struct bttv *btv, const u8 *micro, u32 microlen) 3865 { 3866 u32 n; 3867 u8 bits; 3868 int i; 3869 3870 gpio_inout(0xffffff,BTTV_ALT_DATA|BTTV_ALT_DCLK|BTTV_ALT_NCONFIG); 3871 gpio_write(0); 3872 udelay(PVR_GPIO_DELAY); 3873 3874 gpio_write(BTTV_ALT_NCONFIG); 3875 udelay(PVR_GPIO_DELAY); 3876 3877 for (n = 0; n < microlen; n++) { 3878 bits = micro[n]; 3879 for (i = 0 ; i < 8 ; i++) { 3880 gpio_bits(BTTV_ALT_DCLK,0); 3881 if (bits & 0x01) 3882 gpio_bits(BTTV_ALT_DATA,BTTV_ALT_DATA); 3883 else 3884 gpio_bits(BTTV_ALT_DATA,0); 3885 gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK); 3886 bits >>= 1; 3887 } 3888 } 3889 gpio_bits(BTTV_ALT_DCLK,0); 3890 udelay(PVR_GPIO_DELAY); 3891 3892 /* begin Altera init loop (Not necessary,but doesn't hurt) */ 3893 for (i = 0 ; i < 30 ; i++) { 3894 gpio_bits(BTTV_ALT_DCLK,0); 3895 gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK); 3896 } 3897 gpio_bits(BTTV_ALT_DCLK,0); 3898 return 0; 3899 } 3900 3901 static int pvr_boot(struct bttv *btv) 3902 { 3903 const struct firmware *fw_entry; 3904 int rc; 3905 3906 rc = request_firmware(&fw_entry, "hcwamc.rbf", &btv->c.pci->dev); 3907 if (rc != 0) { 3908 pr_warn("%d: no altera firmware [via hotplug]\n", btv->c.nr); 3909 return rc; 3910 } 3911 rc = pvr_altera_load(btv, fw_entry->data, fw_entry->size); 3912 pr_info("%d: altera firmware upload %s\n", 3913 btv->c.nr, (rc < 0) ? "failed" : "ok"); 3914 release_firmware(fw_entry); 3915 return rc; 3916 } 3917 3918 /* ----------------------------------------------------------------------- */ 3919 /* some osprey specific stuff */ 3920 3921 static void osprey_eeprom(struct bttv *btv, const u8 ee[256]) 3922 { 3923 int i; 3924 u32 serial = 0; 3925 int cardid = -1; 3926 3927 /* This code will nevery actually get called in this case.... */ 3928 if (btv->c.type == BTTV_BOARD_UNKNOWN) { 3929 /* this might be an antique... check for MMAC label in eeprom */ 3930 if (!strncmp(ee, "MMAC", 4)) { 3931 u8 checksum = 0; 3932 for (i = 0; i < 21; i++) 3933 checksum += ee[i]; 3934 if (checksum != ee[21]) 3935 return; 3936 cardid = BTTV_BOARD_OSPREY1x0_848; 3937 for (i = 12; i < 21; i++) 3938 serial *= 10, serial += ee[i] - '0'; 3939 } 3940 } else { 3941 unsigned short type; 3942 3943 for (i = 4 * 16; i < 8 * 16; i += 16) { 3944 u16 checksum = (__force u16)ip_compute_csum(ee + i, 16); 3945 3946 if ((checksum & 0xff) + (checksum >> 8) == 0xff) 3947 break; 3948 } 3949 if (i >= 8*16) 3950 return; 3951 ee += i; 3952 3953 /* found a valid descriptor */ 3954 type = get_unaligned_be16((__be16 *)(ee+4)); 3955 3956 switch(type) { 3957 /* 848 based */ 3958 case 0x0004: 3959 cardid = BTTV_BOARD_OSPREY1x0_848; 3960 break; 3961 case 0x0005: 3962 cardid = BTTV_BOARD_OSPREY101_848; 3963 break; 3964 3965 /* 878 based */ 3966 case 0x0012: 3967 case 0x0013: 3968 cardid = BTTV_BOARD_OSPREY1x0; 3969 break; 3970 case 0x0014: 3971 case 0x0015: 3972 cardid = BTTV_BOARD_OSPREY1x1; 3973 break; 3974 case 0x0016: 3975 case 0x0017: 3976 case 0x0020: 3977 cardid = BTTV_BOARD_OSPREY1x1_SVID; 3978 break; 3979 case 0x0018: 3980 case 0x0019: 3981 case 0x001E: 3982 case 0x001F: 3983 cardid = BTTV_BOARD_OSPREY2xx; 3984 break; 3985 case 0x001A: 3986 case 0x001B: 3987 cardid = BTTV_BOARD_OSPREY2x0_SVID; 3988 break; 3989 case 0x0040: 3990 cardid = BTTV_BOARD_OSPREY500; 3991 break; 3992 case 0x0050: 3993 case 0x0056: 3994 cardid = BTTV_BOARD_OSPREY540; 3995 /* bttv_osprey_540_init(btv); */ 3996 break; 3997 case 0x0060: 3998 case 0x0070: 3999 case 0x00A0: 4000 cardid = BTTV_BOARD_OSPREY2x0; 4001 /* enable output on select control lines */ 4002 gpio_inout(0xffffff,0x000303); 4003 break; 4004 case 0x00D8: 4005 cardid = BTTV_BOARD_OSPREY440; 4006 break; 4007 default: 4008 /* unknown...leave generic, but get serial # */ 4009 pr_info("%d: osprey eeprom: unknown card type 0x%04x\n", 4010 btv->c.nr, type); 4011 break; 4012 } 4013 serial = get_unaligned_be32((__be32 *)(ee+6)); 4014 } 4015 4016 pr_info("%d: osprey eeprom: card=%d '%s' serial=%u\n", 4017 btv->c.nr, cardid, 4018 cardid > 0 ? bttv_tvcards[cardid].name : "Unknown", serial); 4019 4020 if (cardid<0 || btv->c.type == cardid) 4021 return; 4022 4023 /* card type isn't set correctly */ 4024 if (card[btv->c.nr] < bttv_num_tvcards) { 4025 pr_warn("%d: osprey eeprom: Not overriding user specified card type\n", 4026 btv->c.nr); 4027 } else { 4028 pr_info("%d: osprey eeprom: Changing card type from %d to %d\n", 4029 btv->c.nr, btv->c.type, cardid); 4030 btv->c.type = cardid; 4031 } 4032 } 4033 4034 /* ----------------------------------------------------------------------- */ 4035 /* AVermedia specific stuff, from bktr_card.c */ 4036 4037 static int tuner_0_table[] = { 4038 TUNER_PHILIPS_NTSC, TUNER_PHILIPS_PAL /* PAL-BG*/, 4039 TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL /* PAL-I*/, 4040 TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL, 4041 TUNER_PHILIPS_SECAM, TUNER_PHILIPS_SECAM, 4042 TUNER_PHILIPS_SECAM, TUNER_PHILIPS_PAL, 4043 TUNER_PHILIPS_FM1216ME_MK3 }; 4044 4045 static int tuner_1_table[] = { 4046 TUNER_TEMIC_NTSC, TUNER_TEMIC_PAL, 4047 TUNER_TEMIC_PAL, TUNER_TEMIC_PAL, 4048 TUNER_TEMIC_PAL, TUNER_TEMIC_PAL, 4049 TUNER_TEMIC_4012FY5, TUNER_TEMIC_4012FY5, /* TUNER_TEMIC_SECAM */ 4050 TUNER_TEMIC_4012FY5, TUNER_TEMIC_PAL}; 4051 4052 static void avermedia_eeprom(struct bttv *btv) 4053 { 4054 int tuner_make, tuner_tv_fm, tuner_format, tuner_type = 0; 4055 4056 tuner_make = (eeprom_data[0x41] & 0x7); 4057 tuner_tv_fm = (eeprom_data[0x41] & 0x18) >> 3; 4058 tuner_format = (eeprom_data[0x42] & 0xf0) >> 4; 4059 btv->has_remote = (eeprom_data[0x42] & 0x01); 4060 4061 if (tuner_make == 0 || tuner_make == 2) 4062 if (tuner_format <= 0x0a) 4063 tuner_type = tuner_0_table[tuner_format]; 4064 if (tuner_make == 1) 4065 if (tuner_format <= 9) 4066 tuner_type = tuner_1_table[tuner_format]; 4067 4068 if (tuner_make == 4) 4069 if (tuner_format == 0x09) 4070 tuner_type = TUNER_LG_NTSC_NEW_TAPC; /* TAPC-G702P */ 4071 4072 pr_info("%d: Avermedia eeprom[0x%02x%02x]: tuner=", 4073 btv->c.nr, eeprom_data[0x41], eeprom_data[0x42]); 4074 if (tuner_type) { 4075 btv->tuner_type = tuner_type; 4076 pr_cont("%d", tuner_type); 4077 } else 4078 pr_cont("Unknown type"); 4079 pr_cont(" radio:%s remote control:%s\n", 4080 tuner_tv_fm ? "yes" : "no", 4081 btv->has_remote ? "yes" : "no"); 4082 } 4083 4084 /* 4085 * For Voodoo TV/FM and Voodoo 200. These cards' tuners use a TDA9880 4086 * analog demod, which is not I2C controlled like the newer and more common 4087 * TDA9887 series. Instead is has two tri-state input pins, S0 and S1, 4088 * that control the IF for the video and audio. Apparently, bttv GPIO 4089 * 0x10000 is connected to S0. S0 low selects a 38.9 MHz VIF for B/G/D/K/I 4090 * (i.e., PAL) while high selects 45.75 MHz for M/N (i.e., NTSC). 4091 */ 4092 u32 bttv_tda9880_setnorm(struct bttv *btv, u32 gpiobits) 4093 { 4094 4095 if (btv->audio_input == TVAUDIO_INPUT_TUNER) { 4096 if (bttv_tvnorms[btv->tvnorm].v4l2_id & V4L2_STD_MN) 4097 gpiobits |= 0x10000; 4098 else 4099 gpiobits &= ~0x10000; 4100 } 4101 4102 gpio_bits(bttv_tvcards[btv->c.type].gpiomask, gpiobits); 4103 return gpiobits; 4104 } 4105 4106 4107 /* 4108 * reset/enable the MSP on some Hauppauge cards 4109 * Thanks to Kyösti Mälkki (kmalkki@cc.hut.fi)! 4110 * 4111 * Hauppauge: pin 5 4112 * Voodoo: pin 20 4113 */ 4114 static void boot_msp34xx(struct bttv *btv, int pin) 4115 { 4116 int mask = (1 << pin); 4117 4118 gpio_inout(mask,mask); 4119 gpio_bits(mask,0); 4120 mdelay(2); 4121 udelay(500); 4122 gpio_bits(mask,mask); 4123 4124 if (bttv_gpio) 4125 bttv_gpio_tracking(btv,"msp34xx"); 4126 if (bttv_verbose) 4127 pr_info("%d: Hauppauge/Voodoo msp34xx: reset line init [%d]\n", 4128 btv->c.nr, pin); 4129 } 4130 4131 /* ----------------------------------------------------------------------- */ 4132 /* Imagenation L-Model PXC200 Framegrabber */ 4133 /* This is basically the same procedure as 4134 * used by Alessandro Rubini in his pxc200 4135 * driver, but using BTTV functions */ 4136 4137 static void init_PXC200(struct bttv *btv) 4138 { 4139 static int vals[] = { 0x08, 0x09, 0x0a, 0x0b, 0x0d, 0x0d, 0x01, 0x02, 4140 0x03, 0x04, 0x05, 0x06, 0x00 }; 4141 unsigned int i; 4142 int tmp; 4143 u32 val; 4144 4145 /* Initialise GPIO-connevted stuff */ 4146 gpio_inout(0xffffff, (1<<13)); 4147 gpio_write(0); 4148 udelay(3); 4149 gpio_write(1<<13); 4150 /* GPIO inputs are pulled up, so no need to drive 4151 * reset pin any longer */ 4152 gpio_bits(0xffffff, 0); 4153 if (bttv_gpio) 4154 bttv_gpio_tracking(btv,"pxc200"); 4155 4156 /* we could/should try and reset/control the AD pots? but 4157 right now we simply turned off the crushing. Without 4158 this the AGC drifts drifts 4159 remember the EN is reverse logic --> 4160 setting BT848_ADC_AGC_EN disable the AGC 4161 tboult@eecs.lehigh.edu 4162 */ 4163 4164 btwrite(BT848_ADC_RESERVED|BT848_ADC_AGC_EN, BT848_ADC); 4165 4166 /* Initialise MAX517 DAC */ 4167 pr_info("Setting DAC reference voltage level ...\n"); 4168 bttv_I2CWrite(btv,0x5E,0,0x80,1); 4169 4170 /* Initialise 12C508 PIC */ 4171 /* The I2CWrite and I2CRead commands are actually to the 4172 * same chips - but the R/W bit is included in the address 4173 * argument so the numbers are different */ 4174 4175 4176 pr_info("Initialising 12C508 PIC chip ...\n"); 4177 4178 /* First of all, enable the clock line. This is used in the PXC200-F */ 4179 val = btread(BT848_GPIO_DMA_CTL); 4180 val |= BT848_GPIO_DMA_CTL_GPCLKMODE; 4181 btwrite(val, BT848_GPIO_DMA_CTL); 4182 4183 /* Then, push to 0 the reset pin long enough to reset the * 4184 * device same as above for the reset line, but not the same 4185 * value sent to the GPIO-connected stuff 4186 * which one is the good one? */ 4187 gpio_inout(0xffffff,(1<<2)); 4188 gpio_write(0); 4189 udelay(10); 4190 gpio_write(1<<2); 4191 4192 for (i = 0; i < ARRAY_SIZE(vals); i++) { 4193 tmp=bttv_I2CWrite(btv,0x1E,0,vals[i],1); 4194 if (tmp != -1) { 4195 pr_info("I2C Write(%2.2x) = %i\nI2C Read () = %2.2x\n\n", 4196 vals[i],tmp,bttv_I2CRead(btv,0x1F,NULL)); 4197 } 4198 } 4199 4200 pr_info("PXC200 Initialised\n"); 4201 } 4202 4203 4204 4205 /* ----------------------------------------------------------------------- */ 4206 /* 4207 * The Adlink RTV-24 (aka Angelo) has some special initialisation to unlock 4208 * it. This apparently involves the following procedure for each 878 chip: 4209 * 4210 * 1) write 0x00C3FEFF to the GPIO_OUT_EN register 4211 * 4212 * 2) write to GPIO_DATA 4213 * - 0x0E 4214 * - sleep 1ms 4215 * - 0x10 + 0x0E 4216 * - sleep 10ms 4217 * - 0x0E 4218 * read from GPIO_DATA into buf (uint_32) 4219 * - if ( data>>18 & 0x01 != 0) || ( buf>>19 & 0x01 != 1 ) 4220 * error. ERROR_CPLD_Check_Failed stop. 4221 * 4222 * 3) write to GPIO_DATA 4223 * - write 0x4400 + 0x0E 4224 * - sleep 10ms 4225 * - write 0x4410 + 0x0E 4226 * - sleep 1ms 4227 * - write 0x0E 4228 * read from GPIO_DATA into buf (uint_32) 4229 * - if ( buf>>18 & 0x01 ) || ( buf>>19 & 0x01 != 0 ) 4230 * error. ERROR_CPLD_Check_Failed. 4231 */ 4232 /* ----------------------------------------------------------------------- */ 4233 static void 4234 init_RTV24 (struct bttv *btv) 4235 { 4236 uint32_t dataRead = 0; 4237 long watchdog_value = 0x0E; 4238 4239 pr_info("%d: Adlink RTV-24 initialisation in progress ...\n", 4240 btv->c.nr); 4241 4242 btwrite (0x00c3feff, BT848_GPIO_OUT_EN); 4243 4244 btwrite (0 + watchdog_value, BT848_GPIO_DATA); 4245 msleep (1); 4246 btwrite (0x10 + watchdog_value, BT848_GPIO_DATA); 4247 msleep (10); 4248 btwrite (0 + watchdog_value, BT848_GPIO_DATA); 4249 4250 dataRead = btread (BT848_GPIO_DATA); 4251 4252 if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 1)) { 4253 pr_info("%d: Adlink RTV-24 initialisation(1) ERROR_CPLD_Check_Failed (read %d)\n", 4254 btv->c.nr, dataRead); 4255 } 4256 4257 btwrite (0x4400 + watchdog_value, BT848_GPIO_DATA); 4258 msleep (10); 4259 btwrite (0x4410 + watchdog_value, BT848_GPIO_DATA); 4260 msleep (1); 4261 btwrite (watchdog_value, BT848_GPIO_DATA); 4262 msleep (1); 4263 dataRead = btread (BT848_GPIO_DATA); 4264 4265 if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 0)) { 4266 pr_info("%d: Adlink RTV-24 initialisation(2) ERROR_CPLD_Check_Failed (read %d)\n", 4267 btv->c.nr, dataRead); 4268 4269 return; 4270 } 4271 4272 pr_info("%d: Adlink RTV-24 initialisation complete\n", btv->c.nr); 4273 } 4274 4275 4276 4277 /* ----------------------------------------------------------------------- */ 4278 /* 4279 * The PCI-8604PW contains a CPLD, probably an ispMACH 4A, that filters 4280 * the PCI REQ signals coming from the four BT878 chips. After power 4281 * up, the CPLD does not forward requests to the bus, which prevents 4282 * the BT878 from fetching RISC instructions from memory. While the 4283 * CPLD is connected to most of the GPIOs of PCI device 0xD, only 4284 * five appear to play a role in unlocking the REQ signal. The following 4285 * sequence has been determined by trial and error without access to the 4286 * original driver. 4287 * 4288 * Eight GPIOs of device 0xC are provided on connector CN4 (4 in, 4 out). 4289 * Devices 0xE and 0xF do not appear to have anything connected to their 4290 * GPIOs. 4291 * 4292 * The correct GPIO_OUT_EN value might have some more bits set. It should 4293 * be possible to derive it from a boundary scan of the CPLD. Its JTAG 4294 * pins are routed to test points. 4295 * 4296 */ 4297 /* ----------------------------------------------------------------------- */ 4298 static void 4299 init_PCI8604PW(struct bttv *btv) 4300 { 4301 int state; 4302 4303 if ((PCI_SLOT(btv->c.pci->devfn) & ~3) != 0xC) { 4304 pr_warn("This is not a PCI-8604PW\n"); 4305 return; 4306 } 4307 4308 if (PCI_SLOT(btv->c.pci->devfn) != 0xD) 4309 return; 4310 4311 btwrite(0x080002, BT848_GPIO_OUT_EN); 4312 4313 state = (btread(BT848_GPIO_DATA) >> 21) & 7; 4314 4315 for (;;) { 4316 switch (state) { 4317 case 1: 4318 case 5: 4319 case 6: 4320 case 4: 4321 pr_debug("PCI-8604PW in state %i, toggling pin\n", 4322 state); 4323 btwrite(0x080000, BT848_GPIO_DATA); 4324 msleep(1); 4325 btwrite(0x000000, BT848_GPIO_DATA); 4326 msleep(1); 4327 break; 4328 case 7: 4329 pr_info("PCI-8604PW unlocked\n"); 4330 return; 4331 case 0: 4332 /* FIXME: If we are in state 7 and toggle GPIO[19] one 4333 more time, the CPLD goes into state 0, where PCI bus 4334 mastering is inhibited again. We have not managed to 4335 get out of that state. */ 4336 4337 pr_err("PCI-8604PW locked until reset\n"); 4338 return; 4339 default: 4340 pr_err("PCI-8604PW in unknown state %i\n", state); 4341 return; 4342 } 4343 4344 state = (state << 4) | ((btread(BT848_GPIO_DATA) >> 21) & 7); 4345 4346 switch (state) { 4347 case 0x15: 4348 case 0x56: 4349 case 0x64: 4350 case 0x47: 4351 /* The transition from state 7 to state 0 is, as explained 4352 above, valid but undesired and with this code impossible 4353 as we exit as soon as we are in state 7. 4354 case 0x70: */ 4355 break; 4356 default: 4357 pr_err("PCI-8604PW invalid transition %i -> %i\n", 4358 state >> 4, state & 7); 4359 return; 4360 } 4361 state &= 7; 4362 } 4363 } 4364 4365 /* RemoteVision MX (rv605) muxsel helper [Miguel Freitas] 4366 * 4367 * This is needed because rv605 don't use a normal multiplex, but a crosspoint 4368 * switch instead (CD22M3494E). This IC can have multiple active connections 4369 * between Xn (input) and Yn (output) pins. We need to clear any existing 4370 * connection prior to establish a new one, pulsing the STROBE pin. 4371 * 4372 * The board hardwire Y0 (xpoint) to MUX1 and MUXOUT to Yin. 4373 * GPIO pins are wired as: 4374 * GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroller) 4375 * GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroller) 4376 * GPIO[7] - DATA (xpoint) - P1[7] (microcontroller) 4377 * GPIO[8] - - P3[5] (microcontroller) 4378 * GPIO[9] - RESET (xpoint) - P3[6] (microcontroller) 4379 * GPIO[10] - STROBE (xpoint) - P3[7] (microcontroller) 4380 * GPINTR - - P3[4] (microcontroller) 4381 * 4382 * The microcontroller is a 80C32 like. It should be possible to change xpoint 4383 * configuration either directly (as we are doing) or using the microcontroller 4384 * which is also wired to I2C interface. I have no further info on the 4385 * microcontroller features, one would need to disassembly the firmware. 4386 * note: the vendor refused to give any information on this product, all 4387 * that stuff was found using a multimeter! :) 4388 */ 4389 static void rv605_muxsel(struct bttv *btv, unsigned int input) 4390 { 4391 static const u8 muxgpio[] = { 0x3, 0x1, 0x2, 0x4, 0xf, 0x7, 0xe, 0x0, 4392 0xd, 0xb, 0xc, 0x6, 0x9, 0x5, 0x8, 0xa }; 4393 4394 gpio_bits(0x07f, muxgpio[input]); 4395 4396 /* reset all connections */ 4397 gpio_bits(0x200,0x200); 4398 mdelay(1); 4399 gpio_bits(0x200,0x000); 4400 mdelay(1); 4401 4402 /* create a new connection */ 4403 gpio_bits(0x480,0x480); 4404 mdelay(1); 4405 gpio_bits(0x480,0x080); 4406 mdelay(1); 4407 } 4408 4409 /* Tibet Systems 'Progress DVR' CS16 muxsel helper [Chris Fanning] 4410 * 4411 * The CS16 (available on eBay cheap) is a PCI board with four Fusion 4412 * 878A chips, a PCI bridge, an Atmel microcontroller, four sync separator 4413 * chips, ten eight input analog multiplexors, a not chip and a few 4414 * other components. 4415 * 4416 * 16 inputs on a secondary bracket are provided and can be selected 4417 * from each of the four capture chips. Two of the eight input 4418 * multiplexors are used to select from any of the 16 input signals. 4419 * 4420 * Unsupported hardware capabilities: 4421 * . A video output monitor on the secondary bracket can be selected from 4422 * one of the 878A chips. 4423 * . Another passthrough but I haven't spent any time investigating it. 4424 * . Digital I/O (logic level connected to GPIO) is available from an 4425 * onboard header. 4426 * 4427 * The on chip input mux should always be set to 2. 4428 * GPIO[16:19] - Video input selection 4429 * GPIO[0:3] - Video output monitor select (only available from one 878A) 4430 * GPIO[?:?] - Digital I/O. 4431 * 4432 * There is an ATMEL microcontroller with an 8031 core on board. I have not 4433 * determined what function (if any) it provides. With the microcontroller 4434 * and sync separator chips a guess is that it might have to do with video 4435 * switching and maybe some digital I/O. 4436 */ 4437 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input) 4438 { 4439 /* video mux */ 4440 gpio_bits(0x0f0000, input << 16); 4441 } 4442 4443 static void tibetCS16_init(struct bttv *btv) 4444 { 4445 /* enable gpio bits, mask obtained via btSpy */ 4446 gpio_inout(0xffffff, 0x0f7fff); 4447 gpio_write(0x0f7fff); 4448 } 4449 4450 /* 4451 * The following routines for the Kodicom-4400r get a little mind-twisting. 4452 * There is a "master" controller and three "slave" controllers, together 4453 * an analog switch which connects any of 16 cameras to any of the BT87A's. 4454 * The analog switch is controlled by the "master", but the detection order 4455 * of the four BT878A chips is in an order which I just don't understand. 4456 * The "master" is actually the second controller to be detected. The 4457 * logic on the board uses logical numbers for the 4 controllers, but 4458 * those numbers are different from the detection sequence. When working 4459 * with the analog switch, we need to "map" from the detection sequence 4460 * over to the board's logical controller number. This mapping sequence 4461 * is {3, 0, 2, 1}, i.e. the first controller to be detected is logical 4462 * unit 3, the second (which is the master) is logical unit 0, etc. 4463 * We need to maintain the status of the analog switch (which of the 16 4464 * cameras is connected to which of the 4 controllers) in sw_status array. 4465 */ 4466 4467 /* 4468 * First a routine to set the analog switch, which controls which camera 4469 * is routed to which controller. The switch comprises an X-address 4470 * (gpio bits 0-3, representing the camera, ranging from 0-15), and a 4471 * Y-address (gpio bits 4-6, representing the controller, ranging from 0-3). 4472 * A data value (gpio bit 7) of '1' enables the switch, and '0' disables 4473 * the switch. A STROBE bit (gpio bit 8) latches the data value into the 4474 * specified address. The idea is to set the address and data, then bring 4475 * STROBE high, and finally bring STROBE back to low. 4476 */ 4477 static void kodicom4400r_write(struct bttv *btv, 4478 unsigned char xaddr, 4479 unsigned char yaddr, 4480 unsigned char data) { 4481 unsigned int udata; 4482 4483 udata = (data << 7) | ((yaddr&3) << 4) | (xaddr&0xf); 4484 gpio_bits(0x1ff, udata); /* write ADDR and DAT */ 4485 gpio_bits(0x1ff, udata | (1 << 8)); /* strobe high */ 4486 gpio_bits(0x1ff, udata); /* strobe low */ 4487 } 4488 4489 /* 4490 * Next the mux select. Both the "master" and "slave" 'cards' (controllers) 4491 * use this routine. The routine finds the "master" for the card, maps 4492 * the controller number from the detected position over to the logical 4493 * number, writes the appropriate data to the analog switch, and housekeeps 4494 * the local copy of the switch information. The parameter 'input' is the 4495 * requested camera number (0 - 15). 4496 */ 4497 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input) 4498 { 4499 int xaddr, yaddr; 4500 struct bttv *mctlr; 4501 static unsigned char map[4] = {3, 0, 2, 1}; 4502 4503 mctlr = master[btv->c.nr]; 4504 if (mctlr == NULL) { /* ignore if master not yet detected */ 4505 return; 4506 } 4507 yaddr = (btv->c.nr - mctlr->c.nr + 1) & 3; /* the '&' is for safety */ 4508 yaddr = map[yaddr]; 4509 xaddr = input & 0xf; 4510 /* Check if the controller/camera pair has changed, else ignore */ 4511 if (mctlr->sw_status[yaddr] != xaddr) 4512 { 4513 /* "open" the old switch, "close" the new one, save the new */ 4514 kodicom4400r_write(mctlr, mctlr->sw_status[yaddr], yaddr, 0); 4515 mctlr->sw_status[yaddr] = xaddr; 4516 kodicom4400r_write(mctlr, xaddr, yaddr, 1); 4517 } 4518 } 4519 4520 /* 4521 * During initialisation, we need to reset the analog switch. We 4522 * also preset the switch to map the 4 connectors on the card to the 4523 * *user's* (see above description of kodicom4400r_muxsel) channels 4524 * 0 through 3 4525 */ 4526 static void kodicom4400r_init(struct bttv *btv) 4527 { 4528 int ix; 4529 4530 gpio_inout(0x0003ff, 0x0003ff); 4531 gpio_write(1 << 9); /* reset MUX */ 4532 gpio_write(0); 4533 /* Preset camera 0 to the 4 controllers */ 4534 for (ix = 0; ix < 4; ix++) { 4535 btv->sw_status[ix] = ix; 4536 kodicom4400r_write(btv, ix, ix, 1); 4537 } 4538 /* 4539 * Since this is the "master", we need to set up the 4540 * other three controller chips' pointers to this structure 4541 * for later use in the muxsel routine. 4542 */ 4543 if ((btv->c.nr<1) || (btv->c.nr>BTTV_MAX-3)) 4544 return; 4545 master[btv->c.nr-1] = btv; 4546 master[btv->c.nr] = btv; 4547 master[btv->c.nr+1] = btv; 4548 master[btv->c.nr+2] = btv; 4549 } 4550 4551 /* The Grandtec X-Guard framegrabber card uses two Dual 4-channel 4552 * video multiplexers to provide up to 16 video inputs. These 4553 * multiplexers are controlled by the lower 8 GPIO pins of the 4554 * bt878. The multiplexers probably Pericom PI5V331Q or similar. 4555 4556 * xxx0 is pin xxx of multiplexer U5, 4557 * yyy1 is pin yyy of multiplexer U2 4558 */ 4559 #define ENA0 0x01 4560 #define ENB0 0x02 4561 #define ENA1 0x04 4562 #define ENB1 0x08 4563 4564 #define IN10 0x10 4565 #define IN00 0x20 4566 #define IN11 0x40 4567 #define IN01 0x80 4568 4569 static void xguard_muxsel(struct bttv *btv, unsigned int input) 4570 { 4571 static const int masks[] = { 4572 ENB0, ENB0|IN00, ENB0|IN10, ENB0|IN00|IN10, 4573 ENA0, ENA0|IN00, ENA0|IN10, ENA0|IN00|IN10, 4574 ENB1, ENB1|IN01, ENB1|IN11, ENB1|IN01|IN11, 4575 ENA1, ENA1|IN01, ENA1|IN11, ENA1|IN01|IN11, 4576 }; 4577 gpio_write(masks[input%16]); 4578 } 4579 static void picolo_tetra_init(struct bttv *btv) 4580 { 4581 /*This is the video input redirection fonctionality : I DID NOT USED IT. */ 4582 btwrite (0x08<<16,BT848_GPIO_DATA);/*GPIO[19] [==> 4053 B+C] set to 1 */ 4583 btwrite (0x04<<16,BT848_GPIO_DATA);/*GPIO[18] [==> 4053 A] set to 1*/ 4584 } 4585 static void picolo_tetra_muxsel (struct bttv* btv, unsigned int input) 4586 { 4587 4588 dprintk("%d : picolo_tetra_muxsel => input = %d\n", btv->c.nr, input); 4589 /*Just set the right path in the analog multiplexers : channel 1 -> 4 ==> Analog Mux ==> MUX0*/ 4590 /*GPIO[20]&GPIO[21] used to choose the right input*/ 4591 btwrite (input<<20,BT848_GPIO_DATA); 4592 4593 } 4594 4595 /* 4596 * ivc120_muxsel [Added by Alan Garfield <alan@fromorbit.com>] 4597 * 4598 * The IVC120G security card has 4 i2c controlled TDA8540 matrix 4599 * swichers to provide 16 channels to MUX0. The TDA8540's have 4600 * 4 independent outputs and as such the IVC120G also has the 4601 * optional "Monitor Out" bus. This allows the card to be looking 4602 * at one input while the monitor is looking at another. 4603 * 4604 * Since I've couldn't be bothered figuring out how to add an 4605 * independent muxsel for the monitor bus, I've just set it to 4606 * whatever the card is looking at. 4607 * 4608 * OUT0 of the TDA8540's is connected to MUX0 (0x03) 4609 * OUT1 of the TDA8540's is connected to "Monitor Out" (0x0C) 4610 * 4611 * TDA8540_ALT3 IN0-3 = Channel 13 - 16 (0x03) 4612 * TDA8540_ALT4 IN0-3 = Channel 1 - 4 (0x03) 4613 * TDA8540_ALT5 IN0-3 = Channel 5 - 8 (0x03) 4614 * TDA8540_ALT6 IN0-3 = Channel 9 - 12 (0x03) 4615 * 4616 */ 4617 4618 /* All 7 possible sub-ids for the TDA8540 Matrix Switcher */ 4619 #define I2C_TDA8540 0x90 4620 #define I2C_TDA8540_ALT1 0x92 4621 #define I2C_TDA8540_ALT2 0x94 4622 #define I2C_TDA8540_ALT3 0x96 4623 #define I2C_TDA8540_ALT4 0x98 4624 #define I2C_TDA8540_ALT5 0x9a 4625 #define I2C_TDA8540_ALT6 0x9c 4626 4627 static void ivc120_muxsel(struct bttv *btv, unsigned int input) 4628 { 4629 /* Simple maths */ 4630 int key = input % 4; 4631 int matrix = input / 4; 4632 4633 dprintk("%d: ivc120_muxsel: Input - %02d | TDA - %02d | In - %02d\n", 4634 btv->c.nr, input, matrix, key); 4635 4636 /* Handles the input selection on the TDA8540's */ 4637 bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x00, 4638 ((matrix == 3) ? (key | key << 2) : 0x00), 1); 4639 bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x00, 4640 ((matrix == 0) ? (key | key << 2) : 0x00), 1); 4641 bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x00, 4642 ((matrix == 1) ? (key | key << 2) : 0x00), 1); 4643 bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x00, 4644 ((matrix == 2) ? (key | key << 2) : 0x00), 1); 4645 4646 /* Handles the output enables on the TDA8540's */ 4647 bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x02, 4648 ((matrix == 3) ? 0x03 : 0x00), 1); /* 13 - 16 */ 4649 bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x02, 4650 ((matrix == 0) ? 0x03 : 0x00), 1); /* 1-4 */ 4651 bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x02, 4652 ((matrix == 1) ? 0x03 : 0x00), 1); /* 5-8 */ 4653 bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x02, 4654 ((matrix == 2) ? 0x03 : 0x00), 1); /* 9-12 */ 4655 4656 /* 878's MUX0 is already selected for input via muxsel values */ 4657 } 4658 4659 4660 /* PXC200 muxsel helper 4661 * luke@syseng.anu.edu.au 4662 * another transplant 4663 * from Alessandro Rubini (rubini@linux.it) 4664 * 4665 * There are 4 kinds of cards: 4666 * PXC200L which is bt848 4667 * PXC200F which is bt848 with PIC controlling mux 4668 * PXC200AL which is bt878 4669 * PXC200AF which is bt878 with PIC controlling mux 4670 */ 4671 #define PX_CFG_PXC200F 0x01 4672 #define PX_FLAG_PXC200A 0x00001000 /* a pxc200A is bt-878 based */ 4673 #define PX_I2C_PIC 0x0f 4674 #define PX_PXC200A_CARDID 0x200a1295 4675 #define PX_I2C_CMD_CFG 0x00 4676 4677 static void PXC200_muxsel(struct bttv *btv, unsigned int input) 4678 { 4679 int rc; 4680 long mux; 4681 int bitmask; 4682 unsigned char buf[2]; 4683 4684 /* Read PIC config to determine if this is a PXC200F */ 4685 /* PX_I2C_CMD_CFG*/ 4686 buf[0]=0; 4687 buf[1]=0; 4688 rc=bttv_I2CWrite(btv,(PX_I2C_PIC<<1),buf[0],buf[1],1); 4689 if (rc) { 4690 pr_debug("%d: PXC200_muxsel: pic cfg write failed:%d\n", 4691 btv->c.nr, rc); 4692 /* not PXC ? do nothing */ 4693 return; 4694 } 4695 4696 rc=bttv_I2CRead(btv,(PX_I2C_PIC<<1),NULL); 4697 if (!(rc & PX_CFG_PXC200F)) { 4698 pr_debug("%d: PXC200_muxsel: not PXC200F rc:%d\n", 4699 btv->c.nr, rc); 4700 return; 4701 } 4702 4703 4704 /* The multiplexer in the 200F is handled by the GPIO port */ 4705 /* get correct mapping between inputs */ 4706 /* mux = bttv_tvcards[btv->type].muxsel[input] & 3; */ 4707 /* ** not needed!? */ 4708 mux = input; 4709 4710 /* make sure output pins are enabled */ 4711 /* bitmask=0x30f; */ 4712 bitmask=0x302; 4713 /* check whether we have a PXC200A */ 4714 if (btv->cardid == PX_PXC200A_CARDID) { 4715 bitmask ^= 0x180; /* use 7 and 9, not 8 and 9 */ 4716 bitmask |= 7<<4; /* the DAC */ 4717 } 4718 btwrite(bitmask, BT848_GPIO_OUT_EN); 4719 4720 bitmask = btread(BT848_GPIO_DATA); 4721 if (btv->cardid == PX_PXC200A_CARDID) 4722 bitmask = (bitmask & ~0x280) | ((mux & 2) << 8) | ((mux & 1) << 7); 4723 else /* older device */ 4724 bitmask = (bitmask & ~0x300) | ((mux & 3) << 8); 4725 btwrite(bitmask,BT848_GPIO_DATA); 4726 4727 /* 4728 * Was "to be safe, set the bt848 to input 0" 4729 * Actually, since it's ok at load time, better not messing 4730 * with these bits (on PXC200AF you need to set mux 2 here) 4731 * 4732 * needed because bttv-driver sets mux before calling this function 4733 */ 4734 if (btv->cardid == PX_PXC200A_CARDID) 4735 btaor(2<<5, ~BT848_IFORM_MUXSEL, BT848_IFORM); 4736 else /* older device */ 4737 btand(~BT848_IFORM_MUXSEL,BT848_IFORM); 4738 4739 pr_debug("%d: setting input channel to:%d\n", btv->c.nr, (int)mux); 4740 } 4741 4742 static void phytec_muxsel(struct bttv *btv, unsigned int input) 4743 { 4744 unsigned int mux = input % 4; 4745 4746 if (input == btv->svhs) 4747 mux = 0; 4748 4749 gpio_bits(0x3, mux); 4750 } 4751 4752 /* 4753 * GeoVision GV-800(S) functions 4754 * Bruno Christo <bchristo@inf.ufsm.br> 4755 */ 4756 4757 /* This is a function to control the analog switch, which determines which 4758 * camera is routed to which controller. The switch comprises an X-address 4759 * (gpio bits 0-3, representing the camera, ranging from 0-15), and a 4760 * Y-address (gpio bits 4-6, representing the controller, ranging from 0-3). 4761 * A data value (gpio bit 18) of '1' enables the switch, and '0' disables 4762 * the switch. A STROBE bit (gpio bit 17) latches the data value into the 4763 * specified address. There is also a chip select (gpio bit 16). 4764 * The idea is to set the address and chip select together, bring 4765 * STROBE high, write the data, and finally bring STROBE back to low. 4766 */ 4767 static void gv800s_write(struct bttv *btv, 4768 unsigned char xaddr, 4769 unsigned char yaddr, 4770 unsigned char data) { 4771 /* On the "master" 878A: 4772 * GPIO bits 0-9 are used for the analog switch: 4773 * 00 - 03: camera selector 4774 * 04 - 06: 878A (controller) selector 4775 * 16: cselect 4776 * 17: strobe 4777 * 18: data (1->on, 0->off) 4778 * 19: reset 4779 */ 4780 const u32 ADDRESS = ((xaddr&0xf) | (yaddr&3)<<4); 4781 const u32 CSELECT = 1<<16; 4782 const u32 STROBE = 1<<17; 4783 const u32 DATA = data<<18; 4784 4785 gpio_bits(0x1007f, ADDRESS | CSELECT); /* write ADDRESS and CSELECT */ 4786 gpio_bits(0x20000, STROBE); /* STROBE high */ 4787 gpio_bits(0x40000, DATA); /* write DATA */ 4788 gpio_bits(0x20000, ~STROBE); /* STROBE low */ 4789 } 4790 4791 /* 4792 * GeoVision GV-800(S) muxsel 4793 * 4794 * Each of the 4 cards (controllers) use this function. 4795 * The controller using this function selects the input through the GPIO pins 4796 * of the "master" card. A pointer to this card is stored in master[btv->c.nr]. 4797 * 4798 * The parameter 'input' is the requested camera number (0-4) on the controller. 4799 * The map array has the address of each input. Note that the addresses in the 4800 * array are in the sequence the original GeoVision driver uses, that is, set 4801 * every controller to input 0, then to input 1, 2, 3, repeat. This means that 4802 * the physical "camera 1" connector corresponds to controller 0 input 0, 4803 * "camera 2" corresponds to controller 1 input 0, and so on. 4804 * 4805 * After getting the input address, the function then writes the appropriate 4806 * data to the analog switch, and housekeeps the local copy of the switch 4807 * information. 4808 */ 4809 static void gv800s_muxsel(struct bttv *btv, unsigned int input) 4810 { 4811 struct bttv *mctlr; 4812 int xaddr, yaddr; 4813 static unsigned int map[4][4] = { { 0x0, 0x4, 0xa, 0x6 }, 4814 { 0x1, 0x5, 0xb, 0x7 }, 4815 { 0x2, 0x8, 0xc, 0xe }, 4816 { 0x3, 0x9, 0xd, 0xf } }; 4817 input = input%4; 4818 mctlr = master[btv->c.nr]; 4819 if (mctlr == NULL) { 4820 /* do nothing until the "master" is detected */ 4821 return; 4822 } 4823 yaddr = (btv->c.nr - mctlr->c.nr) & 3; 4824 xaddr = map[yaddr][input] & 0xf; 4825 4826 /* Check if the controller/camera pair has changed, ignore otherwise */ 4827 if (mctlr->sw_status[yaddr] != xaddr) { 4828 /* disable the old switch, enable the new one and save status */ 4829 gv800s_write(mctlr, mctlr->sw_status[yaddr], yaddr, 0); 4830 mctlr->sw_status[yaddr] = xaddr; 4831 gv800s_write(mctlr, xaddr, yaddr, 1); 4832 } 4833 } 4834 4835 /* GeoVision GV-800(S) "master" chip init */ 4836 static void gv800s_init(struct bttv *btv) 4837 { 4838 int ix; 4839 4840 gpio_inout(0xf107f, 0xf107f); 4841 gpio_write(1<<19); /* reset the analog MUX */ 4842 gpio_write(0); 4843 4844 /* Preset camera 0 to the 4 controllers */ 4845 for (ix = 0; ix < 4; ix++) { 4846 btv->sw_status[ix] = ix; 4847 gv800s_write(btv, ix, ix, 1); 4848 } 4849 4850 /* Inputs on the "master" controller need this brightness fix */ 4851 bttv_I2CWrite(btv, 0x18, 0x5, 0x90, 1); 4852 4853 if (btv->c.nr > BTTV_MAX-4) 4854 return; 4855 /* 4856 * Store the "master" controller pointer in the master 4857 * array for later use in the muxsel function. 4858 */ 4859 master[btv->c.nr] = btv; 4860 master[btv->c.nr+1] = btv; 4861 master[btv->c.nr+2] = btv; 4862 master[btv->c.nr+3] = btv; 4863 } 4864 4865 /* ----------------------------------------------------------------------- */ 4866 /* motherboard chipset specific stuff */ 4867 4868 void __init bttv_check_chipset(void) 4869 { 4870 int pcipci_fail = 0; 4871 struct pci_dev *dev = NULL; 4872 4873 if (pci_pci_problems & (PCIPCI_FAIL|PCIAGP_FAIL)) /* should check if target is AGP */ 4874 pcipci_fail = 1; 4875 if (pci_pci_problems & (PCIPCI_TRITON|PCIPCI_NATOMA|PCIPCI_VIAETBF)) 4876 triton1 = 1; 4877 if (pci_pci_problems & PCIPCI_VSFX) 4878 vsfx = 1; 4879 #ifdef PCIPCI_ALIMAGIK 4880 if (pci_pci_problems & PCIPCI_ALIMAGIK) 4881 latency = 0x0A; 4882 #endif 4883 4884 4885 /* print warnings about any quirks found */ 4886 if (triton1) 4887 pr_info("Host bridge needs ETBF enabled\n"); 4888 if (vsfx) 4889 pr_info("Host bridge needs VSFX enabled\n"); 4890 if (pcipci_fail) { 4891 pr_info("bttv and your chipset may not work together\n"); 4892 if (!no_overlay) { 4893 pr_info("overlay will be disabled\n"); 4894 no_overlay = 1; 4895 } else { 4896 pr_info("overlay forced. Use this option at your own risk.\n"); 4897 } 4898 } 4899 if (UNSET != latency) 4900 pr_info("pci latency fixup [%d]\n", latency); 4901 while ((dev = pci_get_device(PCI_VENDOR_ID_INTEL, 4902 PCI_DEVICE_ID_INTEL_82441, dev))) { 4903 unsigned char b; 4904 pci_read_config_byte(dev, 0x53, &b); 4905 if (bttv_debug) 4906 pr_info("Host bridge: 82441FX Natoma, bufcon=0x%02x\n", 4907 b); 4908 } 4909 } 4910 4911 int bttv_handle_chipset(struct bttv *btv) 4912 { 4913 unsigned char command; 4914 4915 if (!triton1 && !vsfx && UNSET == latency) 4916 return 0; 4917 4918 if (bttv_verbose) { 4919 if (triton1) 4920 pr_info("%d: enabling ETBF (430FX/VP3 compatibility)\n", 4921 btv->c.nr); 4922 if (vsfx && btv->id >= 878) 4923 pr_info("%d: enabling VSFX\n", btv->c.nr); 4924 if (UNSET != latency) 4925 pr_info("%d: setting pci timer to %d\n", 4926 btv->c.nr, latency); 4927 } 4928 4929 if (btv->id < 878) { 4930 /* bt848 (mis)uses a bit in the irq mask for etbf */ 4931 if (triton1) 4932 btv->triton1 = BT848_INT_ETBF; 4933 } else { 4934 /* bt878 has a bit in the pci config space for it */ 4935 pci_read_config_byte(btv->c.pci, BT878_DEVCTRL, &command); 4936 if (triton1) 4937 command |= BT878_EN_TBFX; 4938 if (vsfx) 4939 command |= BT878_EN_VSFX; 4940 pci_write_config_byte(btv->c.pci, BT878_DEVCTRL, command); 4941 } 4942 if (UNSET != latency) 4943 pci_write_config_byte(btv->c.pci, PCI_LATENCY_TIMER, latency); 4944 return 0; 4945 } 4946