1 /* 2 * A V4L2 driver for OmniVision OV7670 cameras. 3 * 4 * Copyright 2006 One Laptop Per Child Association, Inc. Written 5 * by Jonathan Corbet with substantial inspiration from Mark 6 * McClelland's ovcamchip code. 7 * 8 * Copyright 2006-7 Jonathan Corbet <corbet@lwn.net> 9 * 10 * This file may be distributed under the terms of the GNU General 11 * Public License, version 2. 12 */ 13 #include <linux/clk.h> 14 #include <linux/init.h> 15 #include <linux/module.h> 16 #include <linux/slab.h> 17 #include <linux/i2c.h> 18 #include <linux/delay.h> 19 #include <linux/videodev2.h> 20 #include <linux/gpio.h> 21 #include <linux/gpio/consumer.h> 22 #include <media/v4l2-device.h> 23 #include <media/v4l2-ctrls.h> 24 #include <media/v4l2-mediabus.h> 25 #include <media/v4l2-image-sizes.h> 26 #include <media/i2c/ov7670.h> 27 28 MODULE_AUTHOR("Jonathan Corbet <corbet@lwn.net>"); 29 MODULE_DESCRIPTION("A low-level driver for OmniVision ov7670 sensors"); 30 MODULE_LICENSE("GPL"); 31 32 static bool debug; 33 module_param(debug, bool, 0644); 34 MODULE_PARM_DESC(debug, "Debug level (0-1)"); 35 36 /* 37 * The 7670 sits on i2c with ID 0x42 38 */ 39 #define OV7670_I2C_ADDR 0x42 40 41 #define PLL_FACTOR 4 42 43 /* Registers */ 44 #define REG_GAIN 0x00 /* Gain lower 8 bits (rest in vref) */ 45 #define REG_BLUE 0x01 /* blue gain */ 46 #define REG_RED 0x02 /* red gain */ 47 #define REG_VREF 0x03 /* Pieces of GAIN, VSTART, VSTOP */ 48 #define REG_COM1 0x04 /* Control 1 */ 49 #define COM1_CCIR656 0x40 /* CCIR656 enable */ 50 #define REG_BAVE 0x05 /* U/B Average level */ 51 #define REG_GbAVE 0x06 /* Y/Gb Average level */ 52 #define REG_AECHH 0x07 /* AEC MS 5 bits */ 53 #define REG_RAVE 0x08 /* V/R Average level */ 54 #define REG_COM2 0x09 /* Control 2 */ 55 #define COM2_SSLEEP 0x10 /* Soft sleep mode */ 56 #define REG_PID 0x0a /* Product ID MSB */ 57 #define REG_VER 0x0b /* Product ID LSB */ 58 #define REG_COM3 0x0c /* Control 3 */ 59 #define COM3_SWAP 0x40 /* Byte swap */ 60 #define COM3_SCALEEN 0x08 /* Enable scaling */ 61 #define COM3_DCWEN 0x04 /* Enable downsamp/crop/window */ 62 #define REG_COM4 0x0d /* Control 4 */ 63 #define REG_COM5 0x0e /* All "reserved" */ 64 #define REG_COM6 0x0f /* Control 6 */ 65 #define REG_AECH 0x10 /* More bits of AEC value */ 66 #define REG_CLKRC 0x11 /* Clocl control */ 67 #define CLK_EXT 0x40 /* Use external clock directly */ 68 #define CLK_SCALE 0x3f /* Mask for internal clock scale */ 69 #define REG_COM7 0x12 /* Control 7 */ 70 #define COM7_RESET 0x80 /* Register reset */ 71 #define COM7_FMT_MASK 0x38 72 #define COM7_FMT_VGA 0x00 73 #define COM7_FMT_CIF 0x20 /* CIF format */ 74 #define COM7_FMT_QVGA 0x10 /* QVGA format */ 75 #define COM7_FMT_QCIF 0x08 /* QCIF format */ 76 #define COM7_RGB 0x04 /* bits 0 and 2 - RGB format */ 77 #define COM7_YUV 0x00 /* YUV */ 78 #define COM7_BAYER 0x01 /* Bayer format */ 79 #define COM7_PBAYER 0x05 /* "Processed bayer" */ 80 #define REG_COM8 0x13 /* Control 8 */ 81 #define COM8_FASTAEC 0x80 /* Enable fast AGC/AEC */ 82 #define COM8_AECSTEP 0x40 /* Unlimited AEC step size */ 83 #define COM8_BFILT 0x20 /* Band filter enable */ 84 #define COM8_AGC 0x04 /* Auto gain enable */ 85 #define COM8_AWB 0x02 /* White balance enable */ 86 #define COM8_AEC 0x01 /* Auto exposure enable */ 87 #define REG_COM9 0x14 /* Control 9 - gain ceiling */ 88 #define REG_COM10 0x15 /* Control 10 */ 89 #define COM10_HSYNC 0x40 /* HSYNC instead of HREF */ 90 #define COM10_PCLK_HB 0x20 /* Suppress PCLK on horiz blank */ 91 #define COM10_HREF_REV 0x08 /* Reverse HREF */ 92 #define COM10_VS_LEAD 0x04 /* VSYNC on clock leading edge */ 93 #define COM10_VS_NEG 0x02 /* VSYNC negative */ 94 #define COM10_HS_NEG 0x01 /* HSYNC negative */ 95 #define REG_HSTART 0x17 /* Horiz start high bits */ 96 #define REG_HSTOP 0x18 /* Horiz stop high bits */ 97 #define REG_VSTART 0x19 /* Vert start high bits */ 98 #define REG_VSTOP 0x1a /* Vert stop high bits */ 99 #define REG_PSHFT 0x1b /* Pixel delay after HREF */ 100 #define REG_MIDH 0x1c /* Manuf. ID high */ 101 #define REG_MIDL 0x1d /* Manuf. ID low */ 102 #define REG_MVFP 0x1e /* Mirror / vflip */ 103 #define MVFP_MIRROR 0x20 /* Mirror image */ 104 #define MVFP_FLIP 0x10 /* Vertical flip */ 105 106 #define REG_AEW 0x24 /* AGC upper limit */ 107 #define REG_AEB 0x25 /* AGC lower limit */ 108 #define REG_VPT 0x26 /* AGC/AEC fast mode op region */ 109 #define REG_HSYST 0x30 /* HSYNC rising edge delay */ 110 #define REG_HSYEN 0x31 /* HSYNC falling edge delay */ 111 #define REG_HREF 0x32 /* HREF pieces */ 112 #define REG_TSLB 0x3a /* lots of stuff */ 113 #define TSLB_YLAST 0x04 /* UYVY or VYUY - see com13 */ 114 #define REG_COM11 0x3b /* Control 11 */ 115 #define COM11_NIGHT 0x80 /* NIght mode enable */ 116 #define COM11_NMFR 0x60 /* Two bit NM frame rate */ 117 #define COM11_HZAUTO 0x10 /* Auto detect 50/60 Hz */ 118 #define COM11_50HZ 0x08 /* Manual 50Hz select */ 119 #define COM11_EXP 0x02 120 #define REG_COM12 0x3c /* Control 12 */ 121 #define COM12_HREF 0x80 /* HREF always */ 122 #define REG_COM13 0x3d /* Control 13 */ 123 #define COM13_GAMMA 0x80 /* Gamma enable */ 124 #define COM13_UVSAT 0x40 /* UV saturation auto adjustment */ 125 #define COM13_UVSWAP 0x01 /* V before U - w/TSLB */ 126 #define REG_COM14 0x3e /* Control 14 */ 127 #define COM14_DCWEN 0x10 /* DCW/PCLK-scale enable */ 128 #define REG_EDGE 0x3f /* Edge enhancement factor */ 129 #define REG_COM15 0x40 /* Control 15 */ 130 #define COM15_R10F0 0x00 /* Data range 10 to F0 */ 131 #define COM15_R01FE 0x80 /* 01 to FE */ 132 #define COM15_R00FF 0xc0 /* 00 to FF */ 133 #define COM15_RGB565 0x10 /* RGB565 output */ 134 #define COM15_RGB555 0x30 /* RGB555 output */ 135 #define REG_COM16 0x41 /* Control 16 */ 136 #define COM16_AWBGAIN 0x08 /* AWB gain enable */ 137 #define REG_COM17 0x42 /* Control 17 */ 138 #define COM17_AECWIN 0xc0 /* AEC window - must match COM4 */ 139 #define COM17_CBAR 0x08 /* DSP Color bar */ 140 141 /* 142 * This matrix defines how the colors are generated, must be 143 * tweaked to adjust hue and saturation. 144 * 145 * Order: v-red, v-green, v-blue, u-red, u-green, u-blue 146 * 147 * They are nine-bit signed quantities, with the sign bit 148 * stored in 0x58. Sign for v-red is bit 0, and up from there. 149 */ 150 #define REG_CMATRIX_BASE 0x4f 151 #define CMATRIX_LEN 6 152 #define REG_CMATRIX_SIGN 0x58 153 154 155 #define REG_BRIGHT 0x55 /* Brightness */ 156 #define REG_CONTRAS 0x56 /* Contrast control */ 157 158 #define REG_GFIX 0x69 /* Fix gain control */ 159 160 #define REG_DBLV 0x6b /* PLL control an debugging */ 161 #define DBLV_BYPASS 0x00 /* Bypass PLL */ 162 #define DBLV_X4 0x01 /* clock x4 */ 163 #define DBLV_X6 0x10 /* clock x6 */ 164 #define DBLV_X8 0x11 /* clock x8 */ 165 166 #define REG_REG76 0x76 /* OV's name */ 167 #define R76_BLKPCOR 0x80 /* Black pixel correction enable */ 168 #define R76_WHTPCOR 0x40 /* White pixel correction enable */ 169 170 #define REG_RGB444 0x8c /* RGB 444 control */ 171 #define R444_ENABLE 0x02 /* Turn on RGB444, overrides 5x5 */ 172 #define R444_RGBX 0x01 /* Empty nibble at end */ 173 174 #define REG_HAECC1 0x9f /* Hist AEC/AGC control 1 */ 175 #define REG_HAECC2 0xa0 /* Hist AEC/AGC control 2 */ 176 177 #define REG_BD50MAX 0xa5 /* 50hz banding step limit */ 178 #define REG_HAECC3 0xa6 /* Hist AEC/AGC control 3 */ 179 #define REG_HAECC4 0xa7 /* Hist AEC/AGC control 4 */ 180 #define REG_HAECC5 0xa8 /* Hist AEC/AGC control 5 */ 181 #define REG_HAECC6 0xa9 /* Hist AEC/AGC control 6 */ 182 #define REG_HAECC7 0xaa /* Hist AEC/AGC control 7 */ 183 #define REG_BD60MAX 0xab /* 60hz banding step limit */ 184 185 enum ov7670_model { 186 MODEL_OV7670 = 0, 187 MODEL_OV7675, 188 }; 189 190 struct ov7670_win_size { 191 int width; 192 int height; 193 unsigned char com7_bit; 194 int hstart; /* Start/stop values for the camera. Note */ 195 int hstop; /* that they do not always make complete */ 196 int vstart; /* sense to humans, but evidently the sensor */ 197 int vstop; /* will do the right thing... */ 198 struct regval_list *regs; /* Regs to tweak */ 199 }; 200 201 struct ov7670_devtype { 202 /* formats supported for each model */ 203 struct ov7670_win_size *win_sizes; 204 unsigned int n_win_sizes; 205 /* callbacks for frame rate control */ 206 int (*set_framerate)(struct v4l2_subdev *, struct v4l2_fract *); 207 void (*get_framerate)(struct v4l2_subdev *, struct v4l2_fract *); 208 }; 209 210 /* 211 * Information we maintain about a known sensor. 212 */ 213 struct ov7670_format_struct; /* coming later */ 214 struct ov7670_info { 215 struct v4l2_subdev sd; 216 struct v4l2_ctrl_handler hdl; 217 struct { 218 /* gain cluster */ 219 struct v4l2_ctrl *auto_gain; 220 struct v4l2_ctrl *gain; 221 }; 222 struct { 223 /* exposure cluster */ 224 struct v4l2_ctrl *auto_exposure; 225 struct v4l2_ctrl *exposure; 226 }; 227 struct { 228 /* saturation/hue cluster */ 229 struct v4l2_ctrl *saturation; 230 struct v4l2_ctrl *hue; 231 }; 232 struct ov7670_format_struct *fmt; /* Current format */ 233 struct clk *clk; 234 struct gpio_desc *resetb_gpio; 235 struct gpio_desc *pwdn_gpio; 236 int min_width; /* Filter out smaller sizes */ 237 int min_height; /* Filter out smaller sizes */ 238 int clock_speed; /* External clock speed (MHz) */ 239 u8 clkrc; /* Clock divider value */ 240 bool use_smbus; /* Use smbus I/O instead of I2C */ 241 bool pll_bypass; 242 bool pclk_hb_disable; 243 const struct ov7670_devtype *devtype; /* Device specifics */ 244 }; 245 246 static inline struct ov7670_info *to_state(struct v4l2_subdev *sd) 247 { 248 return container_of(sd, struct ov7670_info, sd); 249 } 250 251 static inline struct v4l2_subdev *to_sd(struct v4l2_ctrl *ctrl) 252 { 253 return &container_of(ctrl->handler, struct ov7670_info, hdl)->sd; 254 } 255 256 257 258 /* 259 * The default register settings, as obtained from OmniVision. There 260 * is really no making sense of most of these - lots of "reserved" values 261 * and such. 262 * 263 * These settings give VGA YUYV. 264 */ 265 266 struct regval_list { 267 unsigned char reg_num; 268 unsigned char value; 269 }; 270 271 static struct regval_list ov7670_default_regs[] = { 272 { REG_COM7, COM7_RESET }, 273 /* 274 * Clock scale: 3 = 15fps 275 * 2 = 20fps 276 * 1 = 30fps 277 */ 278 { REG_CLKRC, 0x1 }, /* OV: clock scale (30 fps) */ 279 { REG_TSLB, 0x04 }, /* OV */ 280 { REG_COM7, 0 }, /* VGA */ 281 /* 282 * Set the hardware window. These values from OV don't entirely 283 * make sense - hstop is less than hstart. But they work... 284 */ 285 { REG_HSTART, 0x13 }, { REG_HSTOP, 0x01 }, 286 { REG_HREF, 0xb6 }, { REG_VSTART, 0x02 }, 287 { REG_VSTOP, 0x7a }, { REG_VREF, 0x0a }, 288 289 { REG_COM3, 0 }, { REG_COM14, 0 }, 290 /* Mystery scaling numbers */ 291 { 0x70, 0x3a }, { 0x71, 0x35 }, 292 { 0x72, 0x11 }, { 0x73, 0xf0 }, 293 { 0xa2, 0x02 }, { REG_COM10, 0x0 }, 294 295 /* Gamma curve values */ 296 { 0x7a, 0x20 }, { 0x7b, 0x10 }, 297 { 0x7c, 0x1e }, { 0x7d, 0x35 }, 298 { 0x7e, 0x5a }, { 0x7f, 0x69 }, 299 { 0x80, 0x76 }, { 0x81, 0x80 }, 300 { 0x82, 0x88 }, { 0x83, 0x8f }, 301 { 0x84, 0x96 }, { 0x85, 0xa3 }, 302 { 0x86, 0xaf }, { 0x87, 0xc4 }, 303 { 0x88, 0xd7 }, { 0x89, 0xe8 }, 304 305 /* AGC and AEC parameters. Note we start by disabling those features, 306 then turn them only after tweaking the values. */ 307 { REG_COM8, COM8_FASTAEC | COM8_AECSTEP | COM8_BFILT }, 308 { REG_GAIN, 0 }, { REG_AECH, 0 }, 309 { REG_COM4, 0x40 }, /* magic reserved bit */ 310 { REG_COM9, 0x18 }, /* 4x gain + magic rsvd bit */ 311 { REG_BD50MAX, 0x05 }, { REG_BD60MAX, 0x07 }, 312 { REG_AEW, 0x95 }, { REG_AEB, 0x33 }, 313 { REG_VPT, 0xe3 }, { REG_HAECC1, 0x78 }, 314 { REG_HAECC2, 0x68 }, { 0xa1, 0x03 }, /* magic */ 315 { REG_HAECC3, 0xd8 }, { REG_HAECC4, 0xd8 }, 316 { REG_HAECC5, 0xf0 }, { REG_HAECC6, 0x90 }, 317 { REG_HAECC7, 0x94 }, 318 { REG_COM8, COM8_FASTAEC|COM8_AECSTEP|COM8_BFILT|COM8_AGC|COM8_AEC }, 319 320 /* Almost all of these are magic "reserved" values. */ 321 { REG_COM5, 0x61 }, { REG_COM6, 0x4b }, 322 { 0x16, 0x02 }, { REG_MVFP, 0x07 }, 323 { 0x21, 0x02 }, { 0x22, 0x91 }, 324 { 0x29, 0x07 }, { 0x33, 0x0b }, 325 { 0x35, 0x0b }, { 0x37, 0x1d }, 326 { 0x38, 0x71 }, { 0x39, 0x2a }, 327 { REG_COM12, 0x78 }, { 0x4d, 0x40 }, 328 { 0x4e, 0x20 }, { REG_GFIX, 0 }, 329 { 0x6b, 0x4a }, { 0x74, 0x10 }, 330 { 0x8d, 0x4f }, { 0x8e, 0 }, 331 { 0x8f, 0 }, { 0x90, 0 }, 332 { 0x91, 0 }, { 0x96, 0 }, 333 { 0x9a, 0 }, { 0xb0, 0x84 }, 334 { 0xb1, 0x0c }, { 0xb2, 0x0e }, 335 { 0xb3, 0x82 }, { 0xb8, 0x0a }, 336 337 /* More reserved magic, some of which tweaks white balance */ 338 { 0x43, 0x0a }, { 0x44, 0xf0 }, 339 { 0x45, 0x34 }, { 0x46, 0x58 }, 340 { 0x47, 0x28 }, { 0x48, 0x3a }, 341 { 0x59, 0x88 }, { 0x5a, 0x88 }, 342 { 0x5b, 0x44 }, { 0x5c, 0x67 }, 343 { 0x5d, 0x49 }, { 0x5e, 0x0e }, 344 { 0x6c, 0x0a }, { 0x6d, 0x55 }, 345 { 0x6e, 0x11 }, { 0x6f, 0x9f }, /* "9e for advance AWB" */ 346 { 0x6a, 0x40 }, { REG_BLUE, 0x40 }, 347 { REG_RED, 0x60 }, 348 { REG_COM8, COM8_FASTAEC|COM8_AECSTEP|COM8_BFILT|COM8_AGC|COM8_AEC|COM8_AWB }, 349 350 /* Matrix coefficients */ 351 { 0x4f, 0x80 }, { 0x50, 0x80 }, 352 { 0x51, 0 }, { 0x52, 0x22 }, 353 { 0x53, 0x5e }, { 0x54, 0x80 }, 354 { 0x58, 0x9e }, 355 356 { REG_COM16, COM16_AWBGAIN }, { REG_EDGE, 0 }, 357 { 0x75, 0x05 }, { 0x76, 0xe1 }, 358 { 0x4c, 0 }, { 0x77, 0x01 }, 359 { REG_COM13, 0xc3 }, { 0x4b, 0x09 }, 360 { 0xc9, 0x60 }, { REG_COM16, 0x38 }, 361 { 0x56, 0x40 }, 362 363 { 0x34, 0x11 }, { REG_COM11, COM11_EXP|COM11_HZAUTO }, 364 { 0xa4, 0x88 }, { 0x96, 0 }, 365 { 0x97, 0x30 }, { 0x98, 0x20 }, 366 { 0x99, 0x30 }, { 0x9a, 0x84 }, 367 { 0x9b, 0x29 }, { 0x9c, 0x03 }, 368 { 0x9d, 0x4c }, { 0x9e, 0x3f }, 369 { 0x78, 0x04 }, 370 371 /* Extra-weird stuff. Some sort of multiplexor register */ 372 { 0x79, 0x01 }, { 0xc8, 0xf0 }, 373 { 0x79, 0x0f }, { 0xc8, 0x00 }, 374 { 0x79, 0x10 }, { 0xc8, 0x7e }, 375 { 0x79, 0x0a }, { 0xc8, 0x80 }, 376 { 0x79, 0x0b }, { 0xc8, 0x01 }, 377 { 0x79, 0x0c }, { 0xc8, 0x0f }, 378 { 0x79, 0x0d }, { 0xc8, 0x20 }, 379 { 0x79, 0x09 }, { 0xc8, 0x80 }, 380 { 0x79, 0x02 }, { 0xc8, 0xc0 }, 381 { 0x79, 0x03 }, { 0xc8, 0x40 }, 382 { 0x79, 0x05 }, { 0xc8, 0x30 }, 383 { 0x79, 0x26 }, 384 385 { 0xff, 0xff }, /* END MARKER */ 386 }; 387 388 389 /* 390 * Here we'll try to encapsulate the changes for just the output 391 * video format. 392 * 393 * RGB656 and YUV422 come from OV; RGB444 is homebrewed. 394 * 395 * IMPORTANT RULE: the first entry must be for COM7, see ov7670_s_fmt for why. 396 */ 397 398 399 static struct regval_list ov7670_fmt_yuv422[] = { 400 { REG_COM7, 0x0 }, /* Selects YUV mode */ 401 { REG_RGB444, 0 }, /* No RGB444 please */ 402 { REG_COM1, 0 }, /* CCIR601 */ 403 { REG_COM15, COM15_R00FF }, 404 { REG_COM9, 0x48 }, /* 32x gain ceiling; 0x8 is reserved bit */ 405 { 0x4f, 0x80 }, /* "matrix coefficient 1" */ 406 { 0x50, 0x80 }, /* "matrix coefficient 2" */ 407 { 0x51, 0 }, /* vb */ 408 { 0x52, 0x22 }, /* "matrix coefficient 4" */ 409 { 0x53, 0x5e }, /* "matrix coefficient 5" */ 410 { 0x54, 0x80 }, /* "matrix coefficient 6" */ 411 { REG_COM13, COM13_GAMMA|COM13_UVSAT }, 412 { 0xff, 0xff }, 413 }; 414 415 static struct regval_list ov7670_fmt_rgb565[] = { 416 { REG_COM7, COM7_RGB }, /* Selects RGB mode */ 417 { REG_RGB444, 0 }, /* No RGB444 please */ 418 { REG_COM1, 0x0 }, /* CCIR601 */ 419 { REG_COM15, COM15_RGB565 }, 420 { REG_COM9, 0x38 }, /* 16x gain ceiling; 0x8 is reserved bit */ 421 { 0x4f, 0xb3 }, /* "matrix coefficient 1" */ 422 { 0x50, 0xb3 }, /* "matrix coefficient 2" */ 423 { 0x51, 0 }, /* vb */ 424 { 0x52, 0x3d }, /* "matrix coefficient 4" */ 425 { 0x53, 0xa7 }, /* "matrix coefficient 5" */ 426 { 0x54, 0xe4 }, /* "matrix coefficient 6" */ 427 { REG_COM13, COM13_GAMMA|COM13_UVSAT }, 428 { 0xff, 0xff }, 429 }; 430 431 static struct regval_list ov7670_fmt_rgb444[] = { 432 { REG_COM7, COM7_RGB }, /* Selects RGB mode */ 433 { REG_RGB444, R444_ENABLE }, /* Enable xxxxrrrr ggggbbbb */ 434 { REG_COM1, 0x0 }, /* CCIR601 */ 435 { REG_COM15, COM15_R01FE|COM15_RGB565 }, /* Data range needed? */ 436 { REG_COM9, 0x38 }, /* 16x gain ceiling; 0x8 is reserved bit */ 437 { 0x4f, 0xb3 }, /* "matrix coefficient 1" */ 438 { 0x50, 0xb3 }, /* "matrix coefficient 2" */ 439 { 0x51, 0 }, /* vb */ 440 { 0x52, 0x3d }, /* "matrix coefficient 4" */ 441 { 0x53, 0xa7 }, /* "matrix coefficient 5" */ 442 { 0x54, 0xe4 }, /* "matrix coefficient 6" */ 443 { REG_COM13, COM13_GAMMA|COM13_UVSAT|0x2 }, /* Magic rsvd bit */ 444 { 0xff, 0xff }, 445 }; 446 447 static struct regval_list ov7670_fmt_raw[] = { 448 { REG_COM7, COM7_BAYER }, 449 { REG_COM13, 0x08 }, /* No gamma, magic rsvd bit */ 450 { REG_COM16, 0x3d }, /* Edge enhancement, denoise */ 451 { REG_REG76, 0xe1 }, /* Pix correction, magic rsvd */ 452 { 0xff, 0xff }, 453 }; 454 455 456 457 /* 458 * Low-level register I/O. 459 * 460 * Note that there are two versions of these. On the XO 1, the 461 * i2c controller only does SMBUS, so that's what we use. The 462 * ov7670 is not really an SMBUS device, though, so the communication 463 * is not always entirely reliable. 464 */ 465 static int ov7670_read_smbus(struct v4l2_subdev *sd, unsigned char reg, 466 unsigned char *value) 467 { 468 struct i2c_client *client = v4l2_get_subdevdata(sd); 469 int ret; 470 471 ret = i2c_smbus_read_byte_data(client, reg); 472 if (ret >= 0) { 473 *value = (unsigned char)ret; 474 ret = 0; 475 } 476 return ret; 477 } 478 479 480 static int ov7670_write_smbus(struct v4l2_subdev *sd, unsigned char reg, 481 unsigned char value) 482 { 483 struct i2c_client *client = v4l2_get_subdevdata(sd); 484 int ret = i2c_smbus_write_byte_data(client, reg, value); 485 486 if (reg == REG_COM7 && (value & COM7_RESET)) 487 msleep(5); /* Wait for reset to run */ 488 return ret; 489 } 490 491 /* 492 * On most platforms, we'd rather do straight i2c I/O. 493 */ 494 static int ov7670_read_i2c(struct v4l2_subdev *sd, unsigned char reg, 495 unsigned char *value) 496 { 497 struct i2c_client *client = v4l2_get_subdevdata(sd); 498 u8 data = reg; 499 struct i2c_msg msg; 500 int ret; 501 502 /* 503 * Send out the register address... 504 */ 505 msg.addr = client->addr; 506 msg.flags = 0; 507 msg.len = 1; 508 msg.buf = &data; 509 ret = i2c_transfer(client->adapter, &msg, 1); 510 if (ret < 0) { 511 printk(KERN_ERR "Error %d on register write\n", ret); 512 return ret; 513 } 514 /* 515 * ...then read back the result. 516 */ 517 msg.flags = I2C_M_RD; 518 ret = i2c_transfer(client->adapter, &msg, 1); 519 if (ret >= 0) { 520 *value = data; 521 ret = 0; 522 } 523 return ret; 524 } 525 526 527 static int ov7670_write_i2c(struct v4l2_subdev *sd, unsigned char reg, 528 unsigned char value) 529 { 530 struct i2c_client *client = v4l2_get_subdevdata(sd); 531 struct i2c_msg msg; 532 unsigned char data[2] = { reg, value }; 533 int ret; 534 535 msg.addr = client->addr; 536 msg.flags = 0; 537 msg.len = 2; 538 msg.buf = data; 539 ret = i2c_transfer(client->adapter, &msg, 1); 540 if (ret > 0) 541 ret = 0; 542 if (reg == REG_COM7 && (value & COM7_RESET)) 543 msleep(5); /* Wait for reset to run */ 544 return ret; 545 } 546 547 static int ov7670_read(struct v4l2_subdev *sd, unsigned char reg, 548 unsigned char *value) 549 { 550 struct ov7670_info *info = to_state(sd); 551 if (info->use_smbus) 552 return ov7670_read_smbus(sd, reg, value); 553 else 554 return ov7670_read_i2c(sd, reg, value); 555 } 556 557 static int ov7670_write(struct v4l2_subdev *sd, unsigned char reg, 558 unsigned char value) 559 { 560 struct ov7670_info *info = to_state(sd); 561 if (info->use_smbus) 562 return ov7670_write_smbus(sd, reg, value); 563 else 564 return ov7670_write_i2c(sd, reg, value); 565 } 566 567 /* 568 * Write a list of register settings; ff/ff stops the process. 569 */ 570 static int ov7670_write_array(struct v4l2_subdev *sd, struct regval_list *vals) 571 { 572 while (vals->reg_num != 0xff || vals->value != 0xff) { 573 int ret = ov7670_write(sd, vals->reg_num, vals->value); 574 if (ret < 0) 575 return ret; 576 vals++; 577 } 578 return 0; 579 } 580 581 582 /* 583 * Stuff that knows about the sensor. 584 */ 585 static int ov7670_reset(struct v4l2_subdev *sd, u32 val) 586 { 587 ov7670_write(sd, REG_COM7, COM7_RESET); 588 msleep(1); 589 return 0; 590 } 591 592 593 static int ov7670_init(struct v4l2_subdev *sd, u32 val) 594 { 595 return ov7670_write_array(sd, ov7670_default_regs); 596 } 597 598 static int ov7670_detect(struct v4l2_subdev *sd) 599 { 600 unsigned char v; 601 int ret; 602 603 ret = ov7670_init(sd, 0); 604 if (ret < 0) 605 return ret; 606 ret = ov7670_read(sd, REG_MIDH, &v); 607 if (ret < 0) 608 return ret; 609 if (v != 0x7f) /* OV manuf. id. */ 610 return -ENODEV; 611 ret = ov7670_read(sd, REG_MIDL, &v); 612 if (ret < 0) 613 return ret; 614 if (v != 0xa2) 615 return -ENODEV; 616 /* 617 * OK, we know we have an OmniVision chip...but which one? 618 */ 619 ret = ov7670_read(sd, REG_PID, &v); 620 if (ret < 0) 621 return ret; 622 if (v != 0x76) /* PID + VER = 0x76 / 0x73 */ 623 return -ENODEV; 624 ret = ov7670_read(sd, REG_VER, &v); 625 if (ret < 0) 626 return ret; 627 if (v != 0x73) /* PID + VER = 0x76 / 0x73 */ 628 return -ENODEV; 629 return 0; 630 } 631 632 633 /* 634 * Store information about the video data format. The color matrix 635 * is deeply tied into the format, so keep the relevant values here. 636 * The magic matrix numbers come from OmniVision. 637 */ 638 static struct ov7670_format_struct { 639 u32 mbus_code; 640 enum v4l2_colorspace colorspace; 641 struct regval_list *regs; 642 int cmatrix[CMATRIX_LEN]; 643 } ov7670_formats[] = { 644 { 645 .mbus_code = MEDIA_BUS_FMT_YUYV8_2X8, 646 .colorspace = V4L2_COLORSPACE_SRGB, 647 .regs = ov7670_fmt_yuv422, 648 .cmatrix = { 128, -128, 0, -34, -94, 128 }, 649 }, 650 { 651 .mbus_code = MEDIA_BUS_FMT_RGB444_2X8_PADHI_LE, 652 .colorspace = V4L2_COLORSPACE_SRGB, 653 .regs = ov7670_fmt_rgb444, 654 .cmatrix = { 179, -179, 0, -61, -176, 228 }, 655 }, 656 { 657 .mbus_code = MEDIA_BUS_FMT_RGB565_2X8_LE, 658 .colorspace = V4L2_COLORSPACE_SRGB, 659 .regs = ov7670_fmt_rgb565, 660 .cmatrix = { 179, -179, 0, -61, -176, 228 }, 661 }, 662 { 663 .mbus_code = MEDIA_BUS_FMT_SBGGR8_1X8, 664 .colorspace = V4L2_COLORSPACE_SRGB, 665 .regs = ov7670_fmt_raw, 666 .cmatrix = { 0, 0, 0, 0, 0, 0 }, 667 }, 668 }; 669 #define N_OV7670_FMTS ARRAY_SIZE(ov7670_formats) 670 671 672 /* 673 * Then there is the issue of window sizes. Try to capture the info here. 674 */ 675 676 /* 677 * QCIF mode is done (by OV) in a very strange way - it actually looks like 678 * VGA with weird scaling options - they do *not* use the canned QCIF mode 679 * which is allegedly provided by the sensor. So here's the weird register 680 * settings. 681 */ 682 static struct regval_list ov7670_qcif_regs[] = { 683 { REG_COM3, COM3_SCALEEN|COM3_DCWEN }, 684 { REG_COM3, COM3_DCWEN }, 685 { REG_COM14, COM14_DCWEN | 0x01}, 686 { 0x73, 0xf1 }, 687 { 0xa2, 0x52 }, 688 { 0x7b, 0x1c }, 689 { 0x7c, 0x28 }, 690 { 0x7d, 0x3c }, 691 { 0x7f, 0x69 }, 692 { REG_COM9, 0x38 }, 693 { 0xa1, 0x0b }, 694 { 0x74, 0x19 }, 695 { 0x9a, 0x80 }, 696 { 0x43, 0x14 }, 697 { REG_COM13, 0xc0 }, 698 { 0xff, 0xff }, 699 }; 700 701 static struct ov7670_win_size ov7670_win_sizes[] = { 702 /* VGA */ 703 { 704 .width = VGA_WIDTH, 705 .height = VGA_HEIGHT, 706 .com7_bit = COM7_FMT_VGA, 707 .hstart = 158, /* These values from */ 708 .hstop = 14, /* Omnivision */ 709 .vstart = 10, 710 .vstop = 490, 711 .regs = NULL, 712 }, 713 /* CIF */ 714 { 715 .width = CIF_WIDTH, 716 .height = CIF_HEIGHT, 717 .com7_bit = COM7_FMT_CIF, 718 .hstart = 170, /* Empirically determined */ 719 .hstop = 90, 720 .vstart = 14, 721 .vstop = 494, 722 .regs = NULL, 723 }, 724 /* QVGA */ 725 { 726 .width = QVGA_WIDTH, 727 .height = QVGA_HEIGHT, 728 .com7_bit = COM7_FMT_QVGA, 729 .hstart = 168, /* Empirically determined */ 730 .hstop = 24, 731 .vstart = 12, 732 .vstop = 492, 733 .regs = NULL, 734 }, 735 /* QCIF */ 736 { 737 .width = QCIF_WIDTH, 738 .height = QCIF_HEIGHT, 739 .com7_bit = COM7_FMT_VGA, /* see comment above */ 740 .hstart = 456, /* Empirically determined */ 741 .hstop = 24, 742 .vstart = 14, 743 .vstop = 494, 744 .regs = ov7670_qcif_regs, 745 } 746 }; 747 748 static struct ov7670_win_size ov7675_win_sizes[] = { 749 /* 750 * Currently, only VGA is supported. Theoretically it could be possible 751 * to support CIF, QVGA and QCIF too. Taking values for ov7670 as a 752 * base and tweak them empirically could be required. 753 */ 754 { 755 .width = VGA_WIDTH, 756 .height = VGA_HEIGHT, 757 .com7_bit = COM7_FMT_VGA, 758 .hstart = 158, /* These values from */ 759 .hstop = 14, /* Omnivision */ 760 .vstart = 14, /* Empirically determined */ 761 .vstop = 494, 762 .regs = NULL, 763 } 764 }; 765 766 static void ov7675_get_framerate(struct v4l2_subdev *sd, 767 struct v4l2_fract *tpf) 768 { 769 struct ov7670_info *info = to_state(sd); 770 u32 clkrc = info->clkrc; 771 int pll_factor; 772 773 if (info->pll_bypass) 774 pll_factor = 1; 775 else 776 pll_factor = PLL_FACTOR; 777 778 clkrc++; 779 if (info->fmt->mbus_code == MEDIA_BUS_FMT_SBGGR8_1X8) 780 clkrc = (clkrc >> 1); 781 782 tpf->numerator = 1; 783 tpf->denominator = (5 * pll_factor * info->clock_speed) / 784 (4 * clkrc); 785 } 786 787 static int ov7675_set_framerate(struct v4l2_subdev *sd, 788 struct v4l2_fract *tpf) 789 { 790 struct ov7670_info *info = to_state(sd); 791 u32 clkrc; 792 int pll_factor; 793 int ret; 794 795 /* 796 * The formula is fps = 5/4*pixclk for YUV/RGB and 797 * fps = 5/2*pixclk for RAW. 798 * 799 * pixclk = clock_speed / (clkrc + 1) * PLLfactor 800 * 801 */ 802 if (info->pll_bypass) { 803 pll_factor = 1; 804 ret = ov7670_write(sd, REG_DBLV, DBLV_BYPASS); 805 } else { 806 pll_factor = PLL_FACTOR; 807 ret = ov7670_write(sd, REG_DBLV, DBLV_X4); 808 } 809 if (ret < 0) 810 return ret; 811 812 if (tpf->numerator == 0 || tpf->denominator == 0) { 813 clkrc = 0; 814 } else { 815 clkrc = (5 * pll_factor * info->clock_speed * tpf->numerator) / 816 (4 * tpf->denominator); 817 if (info->fmt->mbus_code == MEDIA_BUS_FMT_SBGGR8_1X8) 818 clkrc = (clkrc << 1); 819 clkrc--; 820 } 821 822 /* 823 * The datasheet claims that clkrc = 0 will divide the input clock by 1 824 * but we've checked with an oscilloscope that it divides by 2 instead. 825 * So, if clkrc = 0 just bypass the divider. 826 */ 827 if (clkrc <= 0) 828 clkrc = CLK_EXT; 829 else if (clkrc > CLK_SCALE) 830 clkrc = CLK_SCALE; 831 info->clkrc = clkrc; 832 833 /* Recalculate frame rate */ 834 ov7675_get_framerate(sd, tpf); 835 836 ret = ov7670_write(sd, REG_CLKRC, info->clkrc); 837 if (ret < 0) 838 return ret; 839 840 return ov7670_write(sd, REG_DBLV, DBLV_X4); 841 } 842 843 static void ov7670_get_framerate_legacy(struct v4l2_subdev *sd, 844 struct v4l2_fract *tpf) 845 { 846 struct ov7670_info *info = to_state(sd); 847 848 tpf->numerator = 1; 849 tpf->denominator = info->clock_speed; 850 if ((info->clkrc & CLK_EXT) == 0 && (info->clkrc & CLK_SCALE) > 1) 851 tpf->denominator /= (info->clkrc & CLK_SCALE); 852 } 853 854 static int ov7670_set_framerate_legacy(struct v4l2_subdev *sd, 855 struct v4l2_fract *tpf) 856 { 857 struct ov7670_info *info = to_state(sd); 858 int div; 859 860 if (tpf->numerator == 0 || tpf->denominator == 0) 861 div = 1; /* Reset to full rate */ 862 else 863 div = (tpf->numerator * info->clock_speed) / tpf->denominator; 864 if (div == 0) 865 div = 1; 866 else if (div > CLK_SCALE) 867 div = CLK_SCALE; 868 info->clkrc = (info->clkrc & 0x80) | div; 869 tpf->numerator = 1; 870 tpf->denominator = info->clock_speed / div; 871 return ov7670_write(sd, REG_CLKRC, info->clkrc); 872 } 873 874 /* 875 * Store a set of start/stop values into the camera. 876 */ 877 static int ov7670_set_hw(struct v4l2_subdev *sd, int hstart, int hstop, 878 int vstart, int vstop) 879 { 880 int ret; 881 unsigned char v; 882 /* 883 * Horizontal: 11 bits, top 8 live in hstart and hstop. Bottom 3 of 884 * hstart are in href[2:0], bottom 3 of hstop in href[5:3]. There is 885 * a mystery "edge offset" value in the top two bits of href. 886 */ 887 ret = ov7670_write(sd, REG_HSTART, (hstart >> 3) & 0xff); 888 ret += ov7670_write(sd, REG_HSTOP, (hstop >> 3) & 0xff); 889 ret += ov7670_read(sd, REG_HREF, &v); 890 v = (v & 0xc0) | ((hstop & 0x7) << 3) | (hstart & 0x7); 891 msleep(10); 892 ret += ov7670_write(sd, REG_HREF, v); 893 /* 894 * Vertical: similar arrangement, but only 10 bits. 895 */ 896 ret += ov7670_write(sd, REG_VSTART, (vstart >> 2) & 0xff); 897 ret += ov7670_write(sd, REG_VSTOP, (vstop >> 2) & 0xff); 898 ret += ov7670_read(sd, REG_VREF, &v); 899 v = (v & 0xf0) | ((vstop & 0x3) << 2) | (vstart & 0x3); 900 msleep(10); 901 ret += ov7670_write(sd, REG_VREF, v); 902 return ret; 903 } 904 905 906 static int ov7670_enum_mbus_code(struct v4l2_subdev *sd, 907 struct v4l2_subdev_pad_config *cfg, 908 struct v4l2_subdev_mbus_code_enum *code) 909 { 910 if (code->pad || code->index >= N_OV7670_FMTS) 911 return -EINVAL; 912 913 code->code = ov7670_formats[code->index].mbus_code; 914 return 0; 915 } 916 917 static int ov7670_try_fmt_internal(struct v4l2_subdev *sd, 918 struct v4l2_mbus_framefmt *fmt, 919 struct ov7670_format_struct **ret_fmt, 920 struct ov7670_win_size **ret_wsize) 921 { 922 int index, i; 923 struct ov7670_win_size *wsize; 924 struct ov7670_info *info = to_state(sd); 925 unsigned int n_win_sizes = info->devtype->n_win_sizes; 926 unsigned int win_sizes_limit = n_win_sizes; 927 928 for (index = 0; index < N_OV7670_FMTS; index++) 929 if (ov7670_formats[index].mbus_code == fmt->code) 930 break; 931 if (index >= N_OV7670_FMTS) { 932 /* default to first format */ 933 index = 0; 934 fmt->code = ov7670_formats[0].mbus_code; 935 } 936 if (ret_fmt != NULL) 937 *ret_fmt = ov7670_formats + index; 938 /* 939 * Fields: the OV devices claim to be progressive. 940 */ 941 fmt->field = V4L2_FIELD_NONE; 942 943 /* 944 * Don't consider values that don't match min_height and min_width 945 * constraints. 946 */ 947 if (info->min_width || info->min_height) 948 for (i = 0; i < n_win_sizes; i++) { 949 wsize = info->devtype->win_sizes + i; 950 951 if (wsize->width < info->min_width || 952 wsize->height < info->min_height) { 953 win_sizes_limit = i; 954 break; 955 } 956 } 957 /* 958 * Round requested image size down to the nearest 959 * we support, but not below the smallest. 960 */ 961 for (wsize = info->devtype->win_sizes; 962 wsize < info->devtype->win_sizes + win_sizes_limit; wsize++) 963 if (fmt->width >= wsize->width && fmt->height >= wsize->height) 964 break; 965 if (wsize >= info->devtype->win_sizes + win_sizes_limit) 966 wsize--; /* Take the smallest one */ 967 if (ret_wsize != NULL) 968 *ret_wsize = wsize; 969 /* 970 * Note the size we'll actually handle. 971 */ 972 fmt->width = wsize->width; 973 fmt->height = wsize->height; 974 fmt->colorspace = ov7670_formats[index].colorspace; 975 return 0; 976 } 977 978 /* 979 * Set a format. 980 */ 981 static int ov7670_set_fmt(struct v4l2_subdev *sd, 982 struct v4l2_subdev_pad_config *cfg, 983 struct v4l2_subdev_format *format) 984 { 985 struct ov7670_format_struct *ovfmt; 986 struct ov7670_win_size *wsize; 987 struct ov7670_info *info = to_state(sd); 988 unsigned char com7; 989 int ret; 990 991 if (format->pad) 992 return -EINVAL; 993 994 if (format->which == V4L2_SUBDEV_FORMAT_TRY) { 995 ret = ov7670_try_fmt_internal(sd, &format->format, NULL, NULL); 996 if (ret) 997 return ret; 998 cfg->try_fmt = format->format; 999 return 0; 1000 } 1001 1002 ret = ov7670_try_fmt_internal(sd, &format->format, &ovfmt, &wsize); 1003 1004 if (ret) 1005 return ret; 1006 /* 1007 * COM7 is a pain in the ass, it doesn't like to be read then 1008 * quickly written afterward. But we have everything we need 1009 * to set it absolutely here, as long as the format-specific 1010 * register sets list it first. 1011 */ 1012 com7 = ovfmt->regs[0].value; 1013 com7 |= wsize->com7_bit; 1014 ov7670_write(sd, REG_COM7, com7); 1015 /* 1016 * Now write the rest of the array. Also store start/stops 1017 */ 1018 ov7670_write_array(sd, ovfmt->regs + 1); 1019 ov7670_set_hw(sd, wsize->hstart, wsize->hstop, wsize->vstart, 1020 wsize->vstop); 1021 ret = 0; 1022 if (wsize->regs) 1023 ret = ov7670_write_array(sd, wsize->regs); 1024 info->fmt = ovfmt; 1025 1026 /* 1027 * If we're running RGB565, we must rewrite clkrc after setting 1028 * the other parameters or the image looks poor. If we're *not* 1029 * doing RGB565, we must not rewrite clkrc or the image looks 1030 * *really* poor. 1031 * 1032 * (Update) Now that we retain clkrc state, we should be able 1033 * to write it unconditionally, and that will make the frame 1034 * rate persistent too. 1035 */ 1036 if (ret == 0) 1037 ret = ov7670_write(sd, REG_CLKRC, info->clkrc); 1038 return 0; 1039 } 1040 1041 /* 1042 * Implement G/S_PARM. There is a "high quality" mode we could try 1043 * to do someday; for now, we just do the frame rate tweak. 1044 */ 1045 static int ov7670_g_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *parms) 1046 { 1047 struct v4l2_captureparm *cp = &parms->parm.capture; 1048 struct ov7670_info *info = to_state(sd); 1049 1050 if (parms->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) 1051 return -EINVAL; 1052 1053 cp->capability = V4L2_CAP_TIMEPERFRAME; 1054 info->devtype->get_framerate(sd, &cp->timeperframe); 1055 1056 return 0; 1057 } 1058 1059 static int ov7670_s_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *parms) 1060 { 1061 struct v4l2_captureparm *cp = &parms->parm.capture; 1062 struct v4l2_fract *tpf = &cp->timeperframe; 1063 struct ov7670_info *info = to_state(sd); 1064 1065 if (parms->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) 1066 return -EINVAL; 1067 1068 cp->capability = V4L2_CAP_TIMEPERFRAME; 1069 return info->devtype->set_framerate(sd, tpf); 1070 } 1071 1072 1073 /* 1074 * Frame intervals. Since frame rates are controlled with the clock 1075 * divider, we can only do 30/n for integer n values. So no continuous 1076 * or stepwise options. Here we just pick a handful of logical values. 1077 */ 1078 1079 static int ov7670_frame_rates[] = { 30, 15, 10, 5, 1 }; 1080 1081 static int ov7670_enum_frame_interval(struct v4l2_subdev *sd, 1082 struct v4l2_subdev_pad_config *cfg, 1083 struct v4l2_subdev_frame_interval_enum *fie) 1084 { 1085 struct ov7670_info *info = to_state(sd); 1086 unsigned int n_win_sizes = info->devtype->n_win_sizes; 1087 int i; 1088 1089 if (fie->pad) 1090 return -EINVAL; 1091 if (fie->index >= ARRAY_SIZE(ov7670_frame_rates)) 1092 return -EINVAL; 1093 1094 /* 1095 * Check if the width/height is valid. 1096 * 1097 * If a minimum width/height was requested, filter out the capture 1098 * windows that fall outside that. 1099 */ 1100 for (i = 0; i < n_win_sizes; i++) { 1101 struct ov7670_win_size *win = &info->devtype->win_sizes[i]; 1102 1103 if (info->min_width && win->width < info->min_width) 1104 continue; 1105 if (info->min_height && win->height < info->min_height) 1106 continue; 1107 if (fie->width == win->width && fie->height == win->height) 1108 break; 1109 } 1110 if (i == n_win_sizes) 1111 return -EINVAL; 1112 fie->interval.numerator = 1; 1113 fie->interval.denominator = ov7670_frame_rates[fie->index]; 1114 return 0; 1115 } 1116 1117 /* 1118 * Frame size enumeration 1119 */ 1120 static int ov7670_enum_frame_size(struct v4l2_subdev *sd, 1121 struct v4l2_subdev_pad_config *cfg, 1122 struct v4l2_subdev_frame_size_enum *fse) 1123 { 1124 struct ov7670_info *info = to_state(sd); 1125 int i; 1126 int num_valid = -1; 1127 __u32 index = fse->index; 1128 unsigned int n_win_sizes = info->devtype->n_win_sizes; 1129 1130 if (fse->pad) 1131 return -EINVAL; 1132 1133 /* 1134 * If a minimum width/height was requested, filter out the capture 1135 * windows that fall outside that. 1136 */ 1137 for (i = 0; i < n_win_sizes; i++) { 1138 struct ov7670_win_size *win = &info->devtype->win_sizes[i]; 1139 if (info->min_width && win->width < info->min_width) 1140 continue; 1141 if (info->min_height && win->height < info->min_height) 1142 continue; 1143 if (index == ++num_valid) { 1144 fse->min_width = fse->max_width = win->width; 1145 fse->min_height = fse->max_height = win->height; 1146 return 0; 1147 } 1148 } 1149 1150 return -EINVAL; 1151 } 1152 1153 /* 1154 * Code for dealing with controls. 1155 */ 1156 1157 static int ov7670_store_cmatrix(struct v4l2_subdev *sd, 1158 int matrix[CMATRIX_LEN]) 1159 { 1160 int i, ret; 1161 unsigned char signbits = 0; 1162 1163 /* 1164 * Weird crap seems to exist in the upper part of 1165 * the sign bits register, so let's preserve it. 1166 */ 1167 ret = ov7670_read(sd, REG_CMATRIX_SIGN, &signbits); 1168 signbits &= 0xc0; 1169 1170 for (i = 0; i < CMATRIX_LEN; i++) { 1171 unsigned char raw; 1172 1173 if (matrix[i] < 0) { 1174 signbits |= (1 << i); 1175 if (matrix[i] < -255) 1176 raw = 0xff; 1177 else 1178 raw = (-1 * matrix[i]) & 0xff; 1179 } 1180 else { 1181 if (matrix[i] > 255) 1182 raw = 0xff; 1183 else 1184 raw = matrix[i] & 0xff; 1185 } 1186 ret += ov7670_write(sd, REG_CMATRIX_BASE + i, raw); 1187 } 1188 ret += ov7670_write(sd, REG_CMATRIX_SIGN, signbits); 1189 return ret; 1190 } 1191 1192 1193 /* 1194 * Hue also requires messing with the color matrix. It also requires 1195 * trig functions, which tend not to be well supported in the kernel. 1196 * So here is a simple table of sine values, 0-90 degrees, in steps 1197 * of five degrees. Values are multiplied by 1000. 1198 * 1199 * The following naive approximate trig functions require an argument 1200 * carefully limited to -180 <= theta <= 180. 1201 */ 1202 #define SIN_STEP 5 1203 static const int ov7670_sin_table[] = { 1204 0, 87, 173, 258, 342, 422, 1205 499, 573, 642, 707, 766, 819, 1206 866, 906, 939, 965, 984, 996, 1207 1000 1208 }; 1209 1210 static int ov7670_sine(int theta) 1211 { 1212 int chs = 1; 1213 int sine; 1214 1215 if (theta < 0) { 1216 theta = -theta; 1217 chs = -1; 1218 } 1219 if (theta <= 90) 1220 sine = ov7670_sin_table[theta/SIN_STEP]; 1221 else { 1222 theta -= 90; 1223 sine = 1000 - ov7670_sin_table[theta/SIN_STEP]; 1224 } 1225 return sine*chs; 1226 } 1227 1228 static int ov7670_cosine(int theta) 1229 { 1230 theta = 90 - theta; 1231 if (theta > 180) 1232 theta -= 360; 1233 else if (theta < -180) 1234 theta += 360; 1235 return ov7670_sine(theta); 1236 } 1237 1238 1239 1240 1241 static void ov7670_calc_cmatrix(struct ov7670_info *info, 1242 int matrix[CMATRIX_LEN], int sat, int hue) 1243 { 1244 int i; 1245 /* 1246 * Apply the current saturation setting first. 1247 */ 1248 for (i = 0; i < CMATRIX_LEN; i++) 1249 matrix[i] = (info->fmt->cmatrix[i] * sat) >> 7; 1250 /* 1251 * Then, if need be, rotate the hue value. 1252 */ 1253 if (hue != 0) { 1254 int sinth, costh, tmpmatrix[CMATRIX_LEN]; 1255 1256 memcpy(tmpmatrix, matrix, CMATRIX_LEN*sizeof(int)); 1257 sinth = ov7670_sine(hue); 1258 costh = ov7670_cosine(hue); 1259 1260 matrix[0] = (matrix[3]*sinth + matrix[0]*costh)/1000; 1261 matrix[1] = (matrix[4]*sinth + matrix[1]*costh)/1000; 1262 matrix[2] = (matrix[5]*sinth + matrix[2]*costh)/1000; 1263 matrix[3] = (matrix[3]*costh - matrix[0]*sinth)/1000; 1264 matrix[4] = (matrix[4]*costh - matrix[1]*sinth)/1000; 1265 matrix[5] = (matrix[5]*costh - matrix[2]*sinth)/1000; 1266 } 1267 } 1268 1269 1270 1271 static int ov7670_s_sat_hue(struct v4l2_subdev *sd, int sat, int hue) 1272 { 1273 struct ov7670_info *info = to_state(sd); 1274 int matrix[CMATRIX_LEN]; 1275 int ret; 1276 1277 ov7670_calc_cmatrix(info, matrix, sat, hue); 1278 ret = ov7670_store_cmatrix(sd, matrix); 1279 return ret; 1280 } 1281 1282 1283 /* 1284 * Some weird registers seem to store values in a sign/magnitude format! 1285 */ 1286 1287 static unsigned char ov7670_abs_to_sm(unsigned char v) 1288 { 1289 if (v > 127) 1290 return v & 0x7f; 1291 return (128 - v) | 0x80; 1292 } 1293 1294 static int ov7670_s_brightness(struct v4l2_subdev *sd, int value) 1295 { 1296 unsigned char com8 = 0, v; 1297 int ret; 1298 1299 ov7670_read(sd, REG_COM8, &com8); 1300 com8 &= ~COM8_AEC; 1301 ov7670_write(sd, REG_COM8, com8); 1302 v = ov7670_abs_to_sm(value); 1303 ret = ov7670_write(sd, REG_BRIGHT, v); 1304 return ret; 1305 } 1306 1307 static int ov7670_s_contrast(struct v4l2_subdev *sd, int value) 1308 { 1309 return ov7670_write(sd, REG_CONTRAS, (unsigned char) value); 1310 } 1311 1312 static int ov7670_s_hflip(struct v4l2_subdev *sd, int value) 1313 { 1314 unsigned char v = 0; 1315 int ret; 1316 1317 ret = ov7670_read(sd, REG_MVFP, &v); 1318 if (value) 1319 v |= MVFP_MIRROR; 1320 else 1321 v &= ~MVFP_MIRROR; 1322 msleep(10); /* FIXME */ 1323 ret += ov7670_write(sd, REG_MVFP, v); 1324 return ret; 1325 } 1326 1327 static int ov7670_s_vflip(struct v4l2_subdev *sd, int value) 1328 { 1329 unsigned char v = 0; 1330 int ret; 1331 1332 ret = ov7670_read(sd, REG_MVFP, &v); 1333 if (value) 1334 v |= MVFP_FLIP; 1335 else 1336 v &= ~MVFP_FLIP; 1337 msleep(10); /* FIXME */ 1338 ret += ov7670_write(sd, REG_MVFP, v); 1339 return ret; 1340 } 1341 1342 /* 1343 * GAIN is split between REG_GAIN and REG_VREF[7:6]. If one believes 1344 * the data sheet, the VREF parts should be the most significant, but 1345 * experience shows otherwise. There seems to be little value in 1346 * messing with the VREF bits, so we leave them alone. 1347 */ 1348 static int ov7670_g_gain(struct v4l2_subdev *sd, __s32 *value) 1349 { 1350 int ret; 1351 unsigned char gain; 1352 1353 ret = ov7670_read(sd, REG_GAIN, &gain); 1354 *value = gain; 1355 return ret; 1356 } 1357 1358 static int ov7670_s_gain(struct v4l2_subdev *sd, int value) 1359 { 1360 int ret; 1361 unsigned char com8; 1362 1363 ret = ov7670_write(sd, REG_GAIN, value & 0xff); 1364 /* Have to turn off AGC as well */ 1365 if (ret == 0) { 1366 ret = ov7670_read(sd, REG_COM8, &com8); 1367 ret = ov7670_write(sd, REG_COM8, com8 & ~COM8_AGC); 1368 } 1369 return ret; 1370 } 1371 1372 /* 1373 * Tweak autogain. 1374 */ 1375 static int ov7670_s_autogain(struct v4l2_subdev *sd, int value) 1376 { 1377 int ret; 1378 unsigned char com8; 1379 1380 ret = ov7670_read(sd, REG_COM8, &com8); 1381 if (ret == 0) { 1382 if (value) 1383 com8 |= COM8_AGC; 1384 else 1385 com8 &= ~COM8_AGC; 1386 ret = ov7670_write(sd, REG_COM8, com8); 1387 } 1388 return ret; 1389 } 1390 1391 static int ov7670_s_exp(struct v4l2_subdev *sd, int value) 1392 { 1393 int ret; 1394 unsigned char com1, com8, aech, aechh; 1395 1396 ret = ov7670_read(sd, REG_COM1, &com1) + 1397 ov7670_read(sd, REG_COM8, &com8) + 1398 ov7670_read(sd, REG_AECHH, &aechh); 1399 if (ret) 1400 return ret; 1401 1402 com1 = (com1 & 0xfc) | (value & 0x03); 1403 aech = (value >> 2) & 0xff; 1404 aechh = (aechh & 0xc0) | ((value >> 10) & 0x3f); 1405 ret = ov7670_write(sd, REG_COM1, com1) + 1406 ov7670_write(sd, REG_AECH, aech) + 1407 ov7670_write(sd, REG_AECHH, aechh); 1408 /* Have to turn off AEC as well */ 1409 if (ret == 0) 1410 ret = ov7670_write(sd, REG_COM8, com8 & ~COM8_AEC); 1411 return ret; 1412 } 1413 1414 /* 1415 * Tweak autoexposure. 1416 */ 1417 static int ov7670_s_autoexp(struct v4l2_subdev *sd, 1418 enum v4l2_exposure_auto_type value) 1419 { 1420 int ret; 1421 unsigned char com8; 1422 1423 ret = ov7670_read(sd, REG_COM8, &com8); 1424 if (ret == 0) { 1425 if (value == V4L2_EXPOSURE_AUTO) 1426 com8 |= COM8_AEC; 1427 else 1428 com8 &= ~COM8_AEC; 1429 ret = ov7670_write(sd, REG_COM8, com8); 1430 } 1431 return ret; 1432 } 1433 1434 1435 static int ov7670_g_volatile_ctrl(struct v4l2_ctrl *ctrl) 1436 { 1437 struct v4l2_subdev *sd = to_sd(ctrl); 1438 struct ov7670_info *info = to_state(sd); 1439 1440 switch (ctrl->id) { 1441 case V4L2_CID_AUTOGAIN: 1442 return ov7670_g_gain(sd, &info->gain->val); 1443 } 1444 return -EINVAL; 1445 } 1446 1447 static int ov7670_s_ctrl(struct v4l2_ctrl *ctrl) 1448 { 1449 struct v4l2_subdev *sd = to_sd(ctrl); 1450 struct ov7670_info *info = to_state(sd); 1451 1452 switch (ctrl->id) { 1453 case V4L2_CID_BRIGHTNESS: 1454 return ov7670_s_brightness(sd, ctrl->val); 1455 case V4L2_CID_CONTRAST: 1456 return ov7670_s_contrast(sd, ctrl->val); 1457 case V4L2_CID_SATURATION: 1458 return ov7670_s_sat_hue(sd, 1459 info->saturation->val, info->hue->val); 1460 case V4L2_CID_VFLIP: 1461 return ov7670_s_vflip(sd, ctrl->val); 1462 case V4L2_CID_HFLIP: 1463 return ov7670_s_hflip(sd, ctrl->val); 1464 case V4L2_CID_AUTOGAIN: 1465 /* Only set manual gain if auto gain is not explicitly 1466 turned on. */ 1467 if (!ctrl->val) { 1468 /* ov7670_s_gain turns off auto gain */ 1469 return ov7670_s_gain(sd, info->gain->val); 1470 } 1471 return ov7670_s_autogain(sd, ctrl->val); 1472 case V4L2_CID_EXPOSURE_AUTO: 1473 /* Only set manual exposure if auto exposure is not explicitly 1474 turned on. */ 1475 if (ctrl->val == V4L2_EXPOSURE_MANUAL) { 1476 /* ov7670_s_exp turns off auto exposure */ 1477 return ov7670_s_exp(sd, info->exposure->val); 1478 } 1479 return ov7670_s_autoexp(sd, ctrl->val); 1480 } 1481 return -EINVAL; 1482 } 1483 1484 static const struct v4l2_ctrl_ops ov7670_ctrl_ops = { 1485 .s_ctrl = ov7670_s_ctrl, 1486 .g_volatile_ctrl = ov7670_g_volatile_ctrl, 1487 }; 1488 1489 #ifdef CONFIG_VIDEO_ADV_DEBUG 1490 static int ov7670_g_register(struct v4l2_subdev *sd, struct v4l2_dbg_register *reg) 1491 { 1492 unsigned char val = 0; 1493 int ret; 1494 1495 ret = ov7670_read(sd, reg->reg & 0xff, &val); 1496 reg->val = val; 1497 reg->size = 1; 1498 return ret; 1499 } 1500 1501 static int ov7670_s_register(struct v4l2_subdev *sd, const struct v4l2_dbg_register *reg) 1502 { 1503 ov7670_write(sd, reg->reg & 0xff, reg->val & 0xff); 1504 return 0; 1505 } 1506 #endif 1507 1508 /* ----------------------------------------------------------------------- */ 1509 1510 static const struct v4l2_subdev_core_ops ov7670_core_ops = { 1511 .reset = ov7670_reset, 1512 .init = ov7670_init, 1513 #ifdef CONFIG_VIDEO_ADV_DEBUG 1514 .g_register = ov7670_g_register, 1515 .s_register = ov7670_s_register, 1516 #endif 1517 }; 1518 1519 static const struct v4l2_subdev_video_ops ov7670_video_ops = { 1520 .s_parm = ov7670_s_parm, 1521 .g_parm = ov7670_g_parm, 1522 }; 1523 1524 static const struct v4l2_subdev_pad_ops ov7670_pad_ops = { 1525 .enum_frame_interval = ov7670_enum_frame_interval, 1526 .enum_frame_size = ov7670_enum_frame_size, 1527 .enum_mbus_code = ov7670_enum_mbus_code, 1528 .set_fmt = ov7670_set_fmt, 1529 }; 1530 1531 static const struct v4l2_subdev_ops ov7670_ops = { 1532 .core = &ov7670_core_ops, 1533 .video = &ov7670_video_ops, 1534 .pad = &ov7670_pad_ops, 1535 }; 1536 1537 /* ----------------------------------------------------------------------- */ 1538 1539 static const struct ov7670_devtype ov7670_devdata[] = { 1540 [MODEL_OV7670] = { 1541 .win_sizes = ov7670_win_sizes, 1542 .n_win_sizes = ARRAY_SIZE(ov7670_win_sizes), 1543 .set_framerate = ov7670_set_framerate_legacy, 1544 .get_framerate = ov7670_get_framerate_legacy, 1545 }, 1546 [MODEL_OV7675] = { 1547 .win_sizes = ov7675_win_sizes, 1548 .n_win_sizes = ARRAY_SIZE(ov7675_win_sizes), 1549 .set_framerate = ov7675_set_framerate, 1550 .get_framerate = ov7675_get_framerate, 1551 }, 1552 }; 1553 1554 static int ov7670_init_gpio(struct i2c_client *client, struct ov7670_info *info) 1555 { 1556 info->pwdn_gpio = devm_gpiod_get_optional(&client->dev, "powerdown", 1557 GPIOD_OUT_LOW); 1558 if (IS_ERR(info->pwdn_gpio)) { 1559 dev_info(&client->dev, "can't get %s GPIO\n", "powerdown"); 1560 return PTR_ERR(info->pwdn_gpio); 1561 } 1562 1563 info->resetb_gpio = devm_gpiod_get_optional(&client->dev, "reset", 1564 GPIOD_OUT_LOW); 1565 if (IS_ERR(info->resetb_gpio)) { 1566 dev_info(&client->dev, "can't get %s GPIO\n", "reset"); 1567 return PTR_ERR(info->resetb_gpio); 1568 } 1569 1570 usleep_range(3000, 5000); 1571 1572 return 0; 1573 } 1574 1575 static int ov7670_probe(struct i2c_client *client, 1576 const struct i2c_device_id *id) 1577 { 1578 struct v4l2_fract tpf; 1579 struct v4l2_subdev *sd; 1580 struct ov7670_info *info; 1581 int ret; 1582 1583 info = devm_kzalloc(&client->dev, sizeof(*info), GFP_KERNEL); 1584 if (info == NULL) 1585 return -ENOMEM; 1586 sd = &info->sd; 1587 v4l2_i2c_subdev_init(sd, client, &ov7670_ops); 1588 1589 info->clock_speed = 30; /* default: a guess */ 1590 if (client->dev.platform_data) { 1591 struct ov7670_config *config = client->dev.platform_data; 1592 1593 /* 1594 * Must apply configuration before initializing device, because it 1595 * selects I/O method. 1596 */ 1597 info->min_width = config->min_width; 1598 info->min_height = config->min_height; 1599 info->use_smbus = config->use_smbus; 1600 1601 if (config->clock_speed) 1602 info->clock_speed = config->clock_speed; 1603 1604 /* 1605 * It should be allowed for ov7670 too when it is migrated to 1606 * the new frame rate formula. 1607 */ 1608 if (config->pll_bypass && id->driver_data != MODEL_OV7670) 1609 info->pll_bypass = true; 1610 1611 if (config->pclk_hb_disable) 1612 info->pclk_hb_disable = true; 1613 } 1614 1615 info->clk = devm_clk_get(&client->dev, "xclk"); 1616 if (IS_ERR(info->clk)) 1617 return -EPROBE_DEFER; 1618 clk_prepare_enable(info->clk); 1619 1620 ret = ov7670_init_gpio(client, info); 1621 if (ret) 1622 goto clk_disable; 1623 1624 info->clock_speed = clk_get_rate(info->clk) / 1000000; 1625 if (info->clock_speed < 10 || info->clock_speed > 48) { 1626 ret = -EINVAL; 1627 goto clk_disable; 1628 } 1629 1630 /* Make sure it's an ov7670 */ 1631 ret = ov7670_detect(sd); 1632 if (ret) { 1633 v4l_dbg(1, debug, client, 1634 "chip found @ 0x%x (%s) is not an ov7670 chip.\n", 1635 client->addr << 1, client->adapter->name); 1636 goto clk_disable; 1637 } 1638 v4l_info(client, "chip found @ 0x%02x (%s)\n", 1639 client->addr << 1, client->adapter->name); 1640 1641 info->devtype = &ov7670_devdata[id->driver_data]; 1642 info->fmt = &ov7670_formats[0]; 1643 info->clkrc = 0; 1644 1645 /* Set default frame rate to 30 fps */ 1646 tpf.numerator = 1; 1647 tpf.denominator = 30; 1648 info->devtype->set_framerate(sd, &tpf); 1649 1650 if (info->pclk_hb_disable) 1651 ov7670_write(sd, REG_COM10, COM10_PCLK_HB); 1652 1653 v4l2_ctrl_handler_init(&info->hdl, 10); 1654 v4l2_ctrl_new_std(&info->hdl, &ov7670_ctrl_ops, 1655 V4L2_CID_BRIGHTNESS, 0, 255, 1, 128); 1656 v4l2_ctrl_new_std(&info->hdl, &ov7670_ctrl_ops, 1657 V4L2_CID_CONTRAST, 0, 127, 1, 64); 1658 v4l2_ctrl_new_std(&info->hdl, &ov7670_ctrl_ops, 1659 V4L2_CID_VFLIP, 0, 1, 1, 0); 1660 v4l2_ctrl_new_std(&info->hdl, &ov7670_ctrl_ops, 1661 V4L2_CID_HFLIP, 0, 1, 1, 0); 1662 info->saturation = v4l2_ctrl_new_std(&info->hdl, &ov7670_ctrl_ops, 1663 V4L2_CID_SATURATION, 0, 256, 1, 128); 1664 info->hue = v4l2_ctrl_new_std(&info->hdl, &ov7670_ctrl_ops, 1665 V4L2_CID_HUE, -180, 180, 5, 0); 1666 info->gain = v4l2_ctrl_new_std(&info->hdl, &ov7670_ctrl_ops, 1667 V4L2_CID_GAIN, 0, 255, 1, 128); 1668 info->auto_gain = v4l2_ctrl_new_std(&info->hdl, &ov7670_ctrl_ops, 1669 V4L2_CID_AUTOGAIN, 0, 1, 1, 1); 1670 info->exposure = v4l2_ctrl_new_std(&info->hdl, &ov7670_ctrl_ops, 1671 V4L2_CID_EXPOSURE, 0, 65535, 1, 500); 1672 info->auto_exposure = v4l2_ctrl_new_std_menu(&info->hdl, &ov7670_ctrl_ops, 1673 V4L2_CID_EXPOSURE_AUTO, V4L2_EXPOSURE_MANUAL, 0, 1674 V4L2_EXPOSURE_AUTO); 1675 sd->ctrl_handler = &info->hdl; 1676 if (info->hdl.error) { 1677 ret = info->hdl.error; 1678 1679 goto hdl_free; 1680 } 1681 /* 1682 * We have checked empirically that hw allows to read back the gain 1683 * value chosen by auto gain but that's not the case for auto exposure. 1684 */ 1685 v4l2_ctrl_auto_cluster(2, &info->auto_gain, 0, true); 1686 v4l2_ctrl_auto_cluster(2, &info->auto_exposure, 1687 V4L2_EXPOSURE_MANUAL, false); 1688 v4l2_ctrl_cluster(2, &info->saturation); 1689 v4l2_ctrl_handler_setup(&info->hdl); 1690 1691 ret = v4l2_async_register_subdev(&info->sd); 1692 if (ret < 0) 1693 goto hdl_free; 1694 1695 return 0; 1696 1697 hdl_free: 1698 v4l2_ctrl_handler_free(&info->hdl); 1699 clk_disable: 1700 clk_disable_unprepare(info->clk); 1701 return ret; 1702 } 1703 1704 1705 static int ov7670_remove(struct i2c_client *client) 1706 { 1707 struct v4l2_subdev *sd = i2c_get_clientdata(client); 1708 struct ov7670_info *info = to_state(sd); 1709 1710 v4l2_device_unregister_subdev(sd); 1711 v4l2_ctrl_handler_free(&info->hdl); 1712 clk_disable_unprepare(info->clk); 1713 return 0; 1714 } 1715 1716 static const struct i2c_device_id ov7670_id[] = { 1717 { "ov7670", MODEL_OV7670 }, 1718 { "ov7675", MODEL_OV7675 }, 1719 { } 1720 }; 1721 MODULE_DEVICE_TABLE(i2c, ov7670_id); 1722 1723 #if IS_ENABLED(CONFIG_OF) 1724 static const struct of_device_id ov7670_of_match[] = { 1725 { .compatible = "ovti,ov7670", }, 1726 { /* sentinel */ }, 1727 }; 1728 MODULE_DEVICE_TABLE(of, ov7670_of_match); 1729 #endif 1730 1731 static struct i2c_driver ov7670_driver = { 1732 .driver = { 1733 .name = "ov7670", 1734 .of_match_table = of_match_ptr(ov7670_of_match), 1735 }, 1736 .probe = ov7670_probe, 1737 .remove = ov7670_remove, 1738 .id_table = ov7670_id, 1739 }; 1740 1741 module_i2c_driver(ov7670_driver); 1742