1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Maxim MAX9286 GMSL Deserializer Driver 4 * 5 * Copyright (C) 2017-2019 Jacopo Mondi 6 * Copyright (C) 2017-2019 Kieran Bingham 7 * Copyright (C) 2017-2019 Laurent Pinchart 8 * Copyright (C) 2017-2019 Niklas Söderlund 9 * Copyright (C) 2016 Renesas Electronics Corporation 10 * Copyright (C) 2015 Cogent Embedded, Inc. 11 */ 12 13 #include <linux/delay.h> 14 #include <linux/device.h> 15 #include <linux/fwnode.h> 16 #include <linux/gpio/consumer.h> 17 #include <linux/gpio/driver.h> 18 #include <linux/i2c.h> 19 #include <linux/i2c-mux.h> 20 #include <linux/module.h> 21 #include <linux/mutex.h> 22 #include <linux/of_graph.h> 23 #include <linux/regulator/consumer.h> 24 #include <linux/slab.h> 25 26 #include <media/v4l2-async.h> 27 #include <media/v4l2-ctrls.h> 28 #include <media/v4l2-device.h> 29 #include <media/v4l2-fwnode.h> 30 #include <media/v4l2-subdev.h> 31 32 /* Register 0x00 */ 33 #define MAX9286_MSTLINKSEL_AUTO (7 << 5) 34 #define MAX9286_MSTLINKSEL(n) ((n) << 5) 35 #define MAX9286_EN_VS_GEN BIT(4) 36 #define MAX9286_LINKEN(n) (1 << (n)) 37 /* Register 0x01 */ 38 #define MAX9286_FSYNCMODE_ECU (3 << 6) 39 #define MAX9286_FSYNCMODE_EXT (2 << 6) 40 #define MAX9286_FSYNCMODE_INT_OUT (1 << 6) 41 #define MAX9286_FSYNCMODE_INT_HIZ (0 << 6) 42 #define MAX9286_GPIEN BIT(5) 43 #define MAX9286_ENLMO_RSTFSYNC BIT(2) 44 #define MAX9286_FSYNCMETH_AUTO (2 << 0) 45 #define MAX9286_FSYNCMETH_SEMI_AUTO (1 << 0) 46 #define MAX9286_FSYNCMETH_MANUAL (0 << 0) 47 #define MAX9286_REG_FSYNC_PERIOD_L 0x06 48 #define MAX9286_REG_FSYNC_PERIOD_M 0x07 49 #define MAX9286_REG_FSYNC_PERIOD_H 0x08 50 /* Register 0x0a */ 51 #define MAX9286_FWDCCEN(n) (1 << ((n) + 4)) 52 #define MAX9286_REVCCEN(n) (1 << (n)) 53 /* Register 0x0c */ 54 #define MAX9286_HVEN BIT(7) 55 #define MAX9286_EDC_6BIT_HAMMING (2 << 5) 56 #define MAX9286_EDC_6BIT_CRC (1 << 5) 57 #define MAX9286_EDC_1BIT_PARITY (0 << 5) 58 #define MAX9286_DESEL BIT(4) 59 #define MAX9286_INVVS BIT(3) 60 #define MAX9286_INVHS BIT(2) 61 #define MAX9286_HVSRC_D0 (2 << 0) 62 #define MAX9286_HVSRC_D14 (1 << 0) 63 #define MAX9286_HVSRC_D18 (0 << 0) 64 /* Register 0x0f */ 65 #define MAX9286_0X0F_RESERVED BIT(3) 66 /* Register 0x12 */ 67 #define MAX9286_CSILANECNT(n) (((n) - 1) << 6) 68 #define MAX9286_CSIDBL BIT(5) 69 #define MAX9286_DBL BIT(4) 70 #define MAX9286_DATATYPE_USER_8BIT (11 << 0) 71 #define MAX9286_DATATYPE_USER_YUV_12BIT (10 << 0) 72 #define MAX9286_DATATYPE_USER_24BIT (9 << 0) 73 #define MAX9286_DATATYPE_RAW14 (8 << 0) 74 #define MAX9286_DATATYPE_RAW11 (7 << 0) 75 #define MAX9286_DATATYPE_RAW10 (6 << 0) 76 #define MAX9286_DATATYPE_RAW8 (5 << 0) 77 #define MAX9286_DATATYPE_YUV422_10BIT (4 << 0) 78 #define MAX9286_DATATYPE_YUV422_8BIT (3 << 0) 79 #define MAX9286_DATATYPE_RGB555 (2 << 0) 80 #define MAX9286_DATATYPE_RGB565 (1 << 0) 81 #define MAX9286_DATATYPE_RGB888 (0 << 0) 82 /* Register 0x15 */ 83 #define MAX9286_VC(n) ((n) << 5) 84 #define MAX9286_VCTYPE BIT(4) 85 #define MAX9286_CSIOUTEN BIT(3) 86 #define MAX9286_0X15_RESV (3 << 0) 87 /* Register 0x1b */ 88 #define MAX9286_SWITCHIN(n) (1 << ((n) + 4)) 89 #define MAX9286_ENEQ(n) (1 << (n)) 90 /* Register 0x27 */ 91 #define MAX9286_LOCKED BIT(7) 92 /* Register 0x31 */ 93 #define MAX9286_FSYNC_LOCKED BIT(6) 94 /* Register 0x34 */ 95 #define MAX9286_I2CLOCACK BIT(7) 96 #define MAX9286_I2CSLVSH_1046NS_469NS (3 << 5) 97 #define MAX9286_I2CSLVSH_938NS_352NS (2 << 5) 98 #define MAX9286_I2CSLVSH_469NS_234NS (1 << 5) 99 #define MAX9286_I2CSLVSH_352NS_117NS (0 << 5) 100 #define MAX9286_I2CMSTBT_837KBPS (7 << 2) 101 #define MAX9286_I2CMSTBT_533KBPS (6 << 2) 102 #define MAX9286_I2CMSTBT_339KBPS (5 << 2) 103 #define MAX9286_I2CMSTBT_173KBPS (4 << 2) 104 #define MAX9286_I2CMSTBT_105KBPS (3 << 2) 105 #define MAX9286_I2CMSTBT_84KBPS (2 << 2) 106 #define MAX9286_I2CMSTBT_28KBPS (1 << 2) 107 #define MAX9286_I2CMSTBT_8KBPS (0 << 2) 108 #define MAX9286_I2CSLVTO_NONE (3 << 0) 109 #define MAX9286_I2CSLVTO_1024US (2 << 0) 110 #define MAX9286_I2CSLVTO_256US (1 << 0) 111 #define MAX9286_I2CSLVTO_64US (0 << 0) 112 /* Register 0x3b */ 113 #define MAX9286_REV_TRF(n) ((n) << 4) 114 #define MAX9286_REV_AMP(n) ((((n) - 30) / 10) << 1) /* in mV */ 115 #define MAX9286_REV_AMP_X BIT(0) 116 #define MAX9286_REV_AMP_HIGH 170 117 /* Register 0x3f */ 118 #define MAX9286_EN_REV_CFG BIT(6) 119 #define MAX9286_REV_FLEN(n) ((n) - 20) 120 /* Register 0x49 */ 121 #define MAX9286_VIDEO_DETECT_MASK 0x0f 122 /* Register 0x69 */ 123 #define MAX9286_LFLTBMONMASKED BIT(7) 124 #define MAX9286_LOCKMONMASKED BIT(6) 125 #define MAX9286_AUTOCOMBACKEN BIT(5) 126 #define MAX9286_AUTOMASKEN BIT(4) 127 #define MAX9286_MASKLINK(n) ((n) << 0) 128 129 /* 130 * The sink and source pads are created to match the OF graph port numbers so 131 * that their indexes can be used interchangeably. 132 */ 133 #define MAX9286_NUM_GMSL 4 134 #define MAX9286_N_SINKS 4 135 #define MAX9286_N_PADS 5 136 #define MAX9286_SRC_PAD 4 137 138 struct max9286_source { 139 struct v4l2_subdev *sd; 140 struct fwnode_handle *fwnode; 141 }; 142 143 struct max9286_asd { 144 struct v4l2_async_subdev base; 145 struct max9286_source *source; 146 }; 147 148 static inline struct max9286_asd *to_max9286_asd(struct v4l2_async_subdev *asd) 149 { 150 return container_of(asd, struct max9286_asd, base); 151 } 152 153 struct max9286_priv { 154 struct i2c_client *client; 155 struct gpio_desc *gpiod_pwdn; 156 struct v4l2_subdev sd; 157 struct media_pad pads[MAX9286_N_PADS]; 158 struct regulator *regulator; 159 160 struct gpio_chip gpio; 161 u8 gpio_state; 162 163 struct i2c_mux_core *mux; 164 unsigned int mux_channel; 165 bool mux_open; 166 167 /* The initial reverse control channel amplitude. */ 168 u32 init_rev_chan_mv; 169 u32 rev_chan_mv; 170 171 struct v4l2_ctrl_handler ctrls; 172 struct v4l2_ctrl *pixelrate; 173 174 struct v4l2_mbus_framefmt fmt[MAX9286_N_SINKS]; 175 176 /* Protects controls and fmt structures */ 177 struct mutex mutex; 178 179 unsigned int nsources; 180 unsigned int source_mask; 181 unsigned int route_mask; 182 unsigned int bound_sources; 183 unsigned int csi2_data_lanes; 184 struct max9286_source sources[MAX9286_NUM_GMSL]; 185 struct v4l2_async_notifier notifier; 186 }; 187 188 static struct max9286_source *next_source(struct max9286_priv *priv, 189 struct max9286_source *source) 190 { 191 if (!source) 192 source = &priv->sources[0]; 193 else 194 source++; 195 196 for (; source < &priv->sources[MAX9286_NUM_GMSL]; source++) { 197 if (source->fwnode) 198 return source; 199 } 200 201 return NULL; 202 } 203 204 #define for_each_source(priv, source) \ 205 for ((source) = NULL; ((source) = next_source((priv), (source))); ) 206 207 #define to_index(priv, source) ((source) - &(priv)->sources[0]) 208 209 static inline struct max9286_priv *sd_to_max9286(struct v4l2_subdev *sd) 210 { 211 return container_of(sd, struct max9286_priv, sd); 212 } 213 214 /* ----------------------------------------------------------------------------- 215 * I2C IO 216 */ 217 218 static int max9286_read(struct max9286_priv *priv, u8 reg) 219 { 220 int ret; 221 222 ret = i2c_smbus_read_byte_data(priv->client, reg); 223 if (ret < 0) 224 dev_err(&priv->client->dev, 225 "%s: register 0x%02x read failed (%d)\n", 226 __func__, reg, ret); 227 228 return ret; 229 } 230 231 static int max9286_write(struct max9286_priv *priv, u8 reg, u8 val) 232 { 233 int ret; 234 235 ret = i2c_smbus_write_byte_data(priv->client, reg, val); 236 if (ret < 0) 237 dev_err(&priv->client->dev, 238 "%s: register 0x%02x write failed (%d)\n", 239 __func__, reg, ret); 240 241 return ret; 242 } 243 244 /* ----------------------------------------------------------------------------- 245 * I2C Multiplexer 246 */ 247 248 static void max9286_i2c_mux_configure(struct max9286_priv *priv, u8 conf) 249 { 250 max9286_write(priv, 0x0a, conf); 251 252 /* 253 * We must sleep after any change to the forward or reverse channel 254 * configuration. 255 */ 256 usleep_range(3000, 5000); 257 } 258 259 static void max9286_i2c_mux_open(struct max9286_priv *priv) 260 { 261 /* Open all channels on the MAX9286 */ 262 max9286_i2c_mux_configure(priv, 0xff); 263 264 priv->mux_open = true; 265 } 266 267 static void max9286_i2c_mux_close(struct max9286_priv *priv) 268 { 269 /* 270 * Ensure that both the forward and reverse channel are disabled on the 271 * mux, and that the channel ID is invalidated to ensure we reconfigure 272 * on the next max9286_i2c_mux_select() call. 273 */ 274 max9286_i2c_mux_configure(priv, 0x00); 275 276 priv->mux_open = false; 277 priv->mux_channel = -1; 278 } 279 280 static int max9286_i2c_mux_select(struct i2c_mux_core *muxc, u32 chan) 281 { 282 struct max9286_priv *priv = i2c_mux_priv(muxc); 283 284 /* Channel select is disabled when configured in the opened state. */ 285 if (priv->mux_open) 286 return 0; 287 288 if (priv->mux_channel == chan) 289 return 0; 290 291 priv->mux_channel = chan; 292 293 max9286_i2c_mux_configure(priv, MAX9286_FWDCCEN(chan) | 294 MAX9286_REVCCEN(chan)); 295 296 return 0; 297 } 298 299 static int max9286_i2c_mux_init(struct max9286_priv *priv) 300 { 301 struct max9286_source *source; 302 int ret; 303 304 if (!i2c_check_functionality(priv->client->adapter, 305 I2C_FUNC_SMBUS_WRITE_BYTE_DATA)) 306 return -ENODEV; 307 308 priv->mux = i2c_mux_alloc(priv->client->adapter, &priv->client->dev, 309 priv->nsources, 0, I2C_MUX_LOCKED, 310 max9286_i2c_mux_select, NULL); 311 if (!priv->mux) 312 return -ENOMEM; 313 314 priv->mux->priv = priv; 315 316 for_each_source(priv, source) { 317 unsigned int index = to_index(priv, source); 318 319 ret = i2c_mux_add_adapter(priv->mux, 0, index, 0); 320 if (ret < 0) 321 goto error; 322 } 323 324 return 0; 325 326 error: 327 i2c_mux_del_adapters(priv->mux); 328 return ret; 329 } 330 331 static void max9286_configure_i2c(struct max9286_priv *priv, bool localack) 332 { 333 u8 config = MAX9286_I2CSLVSH_469NS_234NS | MAX9286_I2CSLVTO_1024US | 334 MAX9286_I2CMSTBT_105KBPS; 335 336 if (localack) 337 config |= MAX9286_I2CLOCACK; 338 339 max9286_write(priv, 0x34, config); 340 usleep_range(3000, 5000); 341 } 342 343 static void max9286_reverse_channel_setup(struct max9286_priv *priv, 344 unsigned int chan_amplitude) 345 { 346 u8 chan_config; 347 348 if (priv->rev_chan_mv == chan_amplitude) 349 return; 350 351 priv->rev_chan_mv = chan_amplitude; 352 353 /* Reverse channel transmission time: default to 1. */ 354 chan_config = MAX9286_REV_TRF(1); 355 356 /* 357 * Reverse channel setup. 358 * 359 * - Enable custom reverse channel configuration (through register 0x3f) 360 * and set the first pulse length to 35 clock cycles. 361 * - Adjust reverse channel amplitude: values > 130 are programmed 362 * using the additional +100mV REV_AMP_X boost flag 363 */ 364 max9286_write(priv, 0x3f, MAX9286_EN_REV_CFG | MAX9286_REV_FLEN(35)); 365 366 if (chan_amplitude > 100) { 367 /* It is not possible to express values (100 < x < 130) */ 368 chan_amplitude = max(30U, chan_amplitude - 100); 369 chan_config |= MAX9286_REV_AMP_X; 370 } 371 max9286_write(priv, 0x3b, chan_config | MAX9286_REV_AMP(chan_amplitude)); 372 usleep_range(2000, 2500); 373 } 374 375 /* 376 * max9286_check_video_links() - Make sure video links are detected and locked 377 * 378 * Performs safety checks on video link status. Make sure they are detected 379 * and all enabled links are locked. 380 * 381 * Returns 0 for success, -EIO for errors. 382 */ 383 static int max9286_check_video_links(struct max9286_priv *priv) 384 { 385 unsigned int i; 386 int ret; 387 388 /* 389 * Make sure valid video links are detected. 390 * The delay is not characterized in de-serializer manual, wait up 391 * to 5 ms. 392 */ 393 for (i = 0; i < 10; i++) { 394 ret = max9286_read(priv, 0x49); 395 if (ret < 0) 396 return -EIO; 397 398 if ((ret & MAX9286_VIDEO_DETECT_MASK) == priv->source_mask) 399 break; 400 401 usleep_range(350, 500); 402 } 403 404 if (i == 10) { 405 dev_err(&priv->client->dev, 406 "Unable to detect video links: 0x%02x\n", ret); 407 return -EIO; 408 } 409 410 /* Make sure all enabled links are locked (4ms max). */ 411 for (i = 0; i < 10; i++) { 412 ret = max9286_read(priv, 0x27); 413 if (ret < 0) 414 return -EIO; 415 416 if (ret & MAX9286_LOCKED) 417 break; 418 419 usleep_range(350, 450); 420 } 421 422 if (i == 10) { 423 dev_err(&priv->client->dev, "Not all enabled links locked\n"); 424 return -EIO; 425 } 426 427 return 0; 428 } 429 430 /* 431 * max9286_check_config_link() - Detect and wait for configuration links 432 * 433 * Determine if the configuration channel is up and settled for a link. 434 * 435 * Returns 0 for success, -EIO for errors. 436 */ 437 static int max9286_check_config_link(struct max9286_priv *priv, 438 unsigned int source_mask) 439 { 440 unsigned int conflink_mask = (source_mask & 0x0f) << 4; 441 unsigned int i; 442 int ret; 443 444 /* 445 * Make sure requested configuration links are detected. 446 * The delay is not characterized in the chip manual: wait up 447 * to 5 milliseconds. 448 */ 449 for (i = 0; i < 10; i++) { 450 ret = max9286_read(priv, 0x49); 451 if (ret < 0) 452 return -EIO; 453 454 ret &= 0xf0; 455 if (ret == conflink_mask) 456 break; 457 458 usleep_range(350, 500); 459 } 460 461 if (ret != conflink_mask) { 462 dev_err(&priv->client->dev, 463 "Unable to detect configuration links: 0x%02x expected 0x%02x\n", 464 ret, conflink_mask); 465 return -EIO; 466 } 467 468 dev_info(&priv->client->dev, 469 "Successfully detected configuration links after %u loops: 0x%02x\n", 470 i, conflink_mask); 471 472 return 0; 473 } 474 475 /* ----------------------------------------------------------------------------- 476 * V4L2 Subdev 477 */ 478 479 static int max9286_set_pixelrate(struct max9286_priv *priv) 480 { 481 struct max9286_source *source = NULL; 482 u64 pixelrate = 0; 483 484 for_each_source(priv, source) { 485 struct v4l2_ctrl *ctrl; 486 u64 source_rate = 0; 487 488 /* Pixel rate is mandatory to be reported by sources. */ 489 ctrl = v4l2_ctrl_find(source->sd->ctrl_handler, 490 V4L2_CID_PIXEL_RATE); 491 if (!ctrl) { 492 pixelrate = 0; 493 break; 494 } 495 496 /* All source must report the same pixel rate. */ 497 source_rate = v4l2_ctrl_g_ctrl_int64(ctrl); 498 if (!pixelrate) { 499 pixelrate = source_rate; 500 } else if (pixelrate != source_rate) { 501 dev_err(&priv->client->dev, 502 "Unable to calculate pixel rate\n"); 503 return -EINVAL; 504 } 505 } 506 507 if (!pixelrate) { 508 dev_err(&priv->client->dev, 509 "No pixel rate control available in sources\n"); 510 return -EINVAL; 511 } 512 513 /* 514 * The CSI-2 transmitter pixel rate is the single source rate multiplied 515 * by the number of available sources. 516 */ 517 return v4l2_ctrl_s_ctrl_int64(priv->pixelrate, 518 pixelrate * priv->nsources); 519 } 520 521 static int max9286_notify_bound(struct v4l2_async_notifier *notifier, 522 struct v4l2_subdev *subdev, 523 struct v4l2_async_subdev *asd) 524 { 525 struct max9286_priv *priv = sd_to_max9286(notifier->sd); 526 struct max9286_source *source = to_max9286_asd(asd)->source; 527 unsigned int index = to_index(priv, source); 528 unsigned int src_pad; 529 int ret; 530 531 ret = media_entity_get_fwnode_pad(&subdev->entity, 532 source->fwnode, 533 MEDIA_PAD_FL_SOURCE); 534 if (ret < 0) { 535 dev_err(&priv->client->dev, 536 "Failed to find pad for %s\n", subdev->name); 537 return ret; 538 } 539 540 priv->bound_sources |= BIT(index); 541 source->sd = subdev; 542 src_pad = ret; 543 544 ret = media_create_pad_link(&source->sd->entity, src_pad, 545 &priv->sd.entity, index, 546 MEDIA_LNK_FL_ENABLED | 547 MEDIA_LNK_FL_IMMUTABLE); 548 if (ret) { 549 dev_err(&priv->client->dev, 550 "Unable to link %s:%u -> %s:%u\n", 551 source->sd->name, src_pad, priv->sd.name, index); 552 return ret; 553 } 554 555 dev_dbg(&priv->client->dev, "Bound %s pad: %u on index %u\n", 556 subdev->name, src_pad, index); 557 558 /* 559 * As we register a subdev notifiers we won't get a .complete() callback 560 * here, so we have to use bound_sources to identify when all remote 561 * serializers have probed. 562 */ 563 if (priv->bound_sources != priv->source_mask) 564 return 0; 565 566 /* 567 * All enabled sources have probed and enabled their reverse control 568 * channels: 569 * 570 * - Increase the reverse channel amplitude to compensate for the 571 * remote ends high threshold 572 * - Verify all configuration links are properly detected 573 * - Disable auto-ack as communication on the control channel are now 574 * stable. 575 */ 576 max9286_reverse_channel_setup(priv, MAX9286_REV_AMP_HIGH); 577 max9286_check_config_link(priv, priv->source_mask); 578 max9286_configure_i2c(priv, false); 579 580 return max9286_set_pixelrate(priv); 581 } 582 583 static void max9286_notify_unbind(struct v4l2_async_notifier *notifier, 584 struct v4l2_subdev *subdev, 585 struct v4l2_async_subdev *asd) 586 { 587 struct max9286_priv *priv = sd_to_max9286(notifier->sd); 588 struct max9286_source *source = to_max9286_asd(asd)->source; 589 unsigned int index = to_index(priv, source); 590 591 source->sd = NULL; 592 priv->bound_sources &= ~BIT(index); 593 } 594 595 static const struct v4l2_async_notifier_operations max9286_notify_ops = { 596 .bound = max9286_notify_bound, 597 .unbind = max9286_notify_unbind, 598 }; 599 600 static int max9286_v4l2_notifier_register(struct max9286_priv *priv) 601 { 602 struct device *dev = &priv->client->dev; 603 struct max9286_source *source = NULL; 604 int ret; 605 606 if (!priv->nsources) 607 return 0; 608 609 v4l2_async_nf_init(&priv->notifier); 610 611 for_each_source(priv, source) { 612 unsigned int i = to_index(priv, source); 613 struct max9286_asd *mas; 614 615 mas = v4l2_async_nf_add_fwnode(&priv->notifier, source->fwnode, 616 struct max9286_asd); 617 if (IS_ERR(mas)) { 618 dev_err(dev, "Failed to add subdev for source %u: %ld", 619 i, PTR_ERR(mas)); 620 v4l2_async_nf_cleanup(&priv->notifier); 621 return PTR_ERR(mas); 622 } 623 624 mas->source = source; 625 } 626 627 priv->notifier.ops = &max9286_notify_ops; 628 629 ret = v4l2_async_subdev_nf_register(&priv->sd, &priv->notifier); 630 if (ret) { 631 dev_err(dev, "Failed to register subdev_notifier"); 632 v4l2_async_nf_cleanup(&priv->notifier); 633 return ret; 634 } 635 636 return 0; 637 } 638 639 static void max9286_v4l2_notifier_unregister(struct max9286_priv *priv) 640 { 641 if (!priv->nsources) 642 return; 643 644 v4l2_async_nf_unregister(&priv->notifier); 645 v4l2_async_nf_cleanup(&priv->notifier); 646 } 647 648 static int max9286_s_stream(struct v4l2_subdev *sd, int enable) 649 { 650 struct max9286_priv *priv = sd_to_max9286(sd); 651 struct max9286_source *source; 652 unsigned int i; 653 bool sync = false; 654 int ret; 655 656 if (enable) { 657 /* 658 * The frame sync between cameras is transmitted across the 659 * reverse channel as GPIO. We must open all channels while 660 * streaming to allow this synchronisation signal to be shared. 661 */ 662 max9286_i2c_mux_open(priv); 663 664 /* Start all cameras. */ 665 for_each_source(priv, source) { 666 ret = v4l2_subdev_call(source->sd, video, s_stream, 1); 667 if (ret) 668 return ret; 669 } 670 671 ret = max9286_check_video_links(priv); 672 if (ret) 673 return ret; 674 675 /* 676 * Wait until frame synchronization is locked. 677 * 678 * Manual says frame sync locking should take ~6 VTS. 679 * From practical experience at least 8 are required. Give 680 * 12 complete frames time (~400ms at 30 fps) to achieve frame 681 * locking before returning error. 682 */ 683 for (i = 0; i < 40; i++) { 684 if (max9286_read(priv, 0x31) & MAX9286_FSYNC_LOCKED) { 685 sync = true; 686 break; 687 } 688 usleep_range(9000, 11000); 689 } 690 691 if (!sync) { 692 dev_err(&priv->client->dev, 693 "Failed to get frame synchronization\n"); 694 return -EXDEV; /* Invalid cross-device link */ 695 } 696 697 /* 698 * Enable CSI output, VC set according to link number. 699 * Bit 7 must be set (chip manual says it's 0 and reserved). 700 */ 701 max9286_write(priv, 0x15, 0x80 | MAX9286_VCTYPE | 702 MAX9286_CSIOUTEN | MAX9286_0X15_RESV); 703 } else { 704 max9286_write(priv, 0x15, MAX9286_VCTYPE | MAX9286_0X15_RESV); 705 706 /* Stop all cameras. */ 707 for_each_source(priv, source) 708 v4l2_subdev_call(source->sd, video, s_stream, 0); 709 710 max9286_i2c_mux_close(priv); 711 } 712 713 return 0; 714 } 715 716 static int max9286_enum_mbus_code(struct v4l2_subdev *sd, 717 struct v4l2_subdev_state *sd_state, 718 struct v4l2_subdev_mbus_code_enum *code) 719 { 720 if (code->pad || code->index > 0) 721 return -EINVAL; 722 723 code->code = MEDIA_BUS_FMT_UYVY8_1X16; 724 725 return 0; 726 } 727 728 static struct v4l2_mbus_framefmt * 729 max9286_get_pad_format(struct max9286_priv *priv, 730 struct v4l2_subdev_state *sd_state, 731 unsigned int pad, u32 which) 732 { 733 switch (which) { 734 case V4L2_SUBDEV_FORMAT_TRY: 735 return v4l2_subdev_get_try_format(&priv->sd, sd_state, pad); 736 case V4L2_SUBDEV_FORMAT_ACTIVE: 737 return &priv->fmt[pad]; 738 default: 739 return NULL; 740 } 741 } 742 743 static int max9286_set_fmt(struct v4l2_subdev *sd, 744 struct v4l2_subdev_state *sd_state, 745 struct v4l2_subdev_format *format) 746 { 747 struct max9286_priv *priv = sd_to_max9286(sd); 748 struct v4l2_mbus_framefmt *cfg_fmt; 749 750 if (format->pad == MAX9286_SRC_PAD) 751 return -EINVAL; 752 753 /* Refuse non YUV422 formats as we hardcode DT to 8 bit YUV422 */ 754 switch (format->format.code) { 755 case MEDIA_BUS_FMT_UYVY8_1X16: 756 case MEDIA_BUS_FMT_VYUY8_1X16: 757 case MEDIA_BUS_FMT_YUYV8_1X16: 758 case MEDIA_BUS_FMT_YVYU8_1X16: 759 break; 760 default: 761 format->format.code = MEDIA_BUS_FMT_UYVY8_1X16; 762 break; 763 } 764 765 cfg_fmt = max9286_get_pad_format(priv, sd_state, format->pad, 766 format->which); 767 if (!cfg_fmt) 768 return -EINVAL; 769 770 mutex_lock(&priv->mutex); 771 *cfg_fmt = format->format; 772 mutex_unlock(&priv->mutex); 773 774 return 0; 775 } 776 777 static int max9286_get_fmt(struct v4l2_subdev *sd, 778 struct v4l2_subdev_state *sd_state, 779 struct v4l2_subdev_format *format) 780 { 781 struct max9286_priv *priv = sd_to_max9286(sd); 782 struct v4l2_mbus_framefmt *cfg_fmt; 783 unsigned int pad = format->pad; 784 785 /* 786 * Multiplexed Stream Support: Support link validation by returning the 787 * format of the first bound link. All links must have the same format, 788 * as we do not support mixing and matching of cameras connected to the 789 * max9286. 790 */ 791 if (pad == MAX9286_SRC_PAD) 792 pad = __ffs(priv->bound_sources); 793 794 cfg_fmt = max9286_get_pad_format(priv, sd_state, pad, format->which); 795 if (!cfg_fmt) 796 return -EINVAL; 797 798 mutex_lock(&priv->mutex); 799 format->format = *cfg_fmt; 800 mutex_unlock(&priv->mutex); 801 802 return 0; 803 } 804 805 static const struct v4l2_subdev_video_ops max9286_video_ops = { 806 .s_stream = max9286_s_stream, 807 }; 808 809 static const struct v4l2_subdev_pad_ops max9286_pad_ops = { 810 .enum_mbus_code = max9286_enum_mbus_code, 811 .get_fmt = max9286_get_fmt, 812 .set_fmt = max9286_set_fmt, 813 }; 814 815 static const struct v4l2_subdev_ops max9286_subdev_ops = { 816 .video = &max9286_video_ops, 817 .pad = &max9286_pad_ops, 818 }; 819 820 static void max9286_init_format(struct v4l2_mbus_framefmt *fmt) 821 { 822 fmt->width = 1280; 823 fmt->height = 800; 824 fmt->code = MEDIA_BUS_FMT_UYVY8_1X16; 825 fmt->colorspace = V4L2_COLORSPACE_SRGB; 826 fmt->field = V4L2_FIELD_NONE; 827 fmt->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT; 828 fmt->quantization = V4L2_QUANTIZATION_DEFAULT; 829 fmt->xfer_func = V4L2_XFER_FUNC_DEFAULT; 830 } 831 832 static int max9286_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh) 833 { 834 struct v4l2_mbus_framefmt *format; 835 unsigned int i; 836 837 for (i = 0; i < MAX9286_N_SINKS; i++) { 838 format = v4l2_subdev_get_try_format(subdev, fh->state, i); 839 max9286_init_format(format); 840 } 841 842 return 0; 843 } 844 845 static const struct v4l2_subdev_internal_ops max9286_subdev_internal_ops = { 846 .open = max9286_open, 847 }; 848 849 static int max9286_s_ctrl(struct v4l2_ctrl *ctrl) 850 { 851 switch (ctrl->id) { 852 case V4L2_CID_PIXEL_RATE: 853 return 0; 854 default: 855 return -EINVAL; 856 } 857 } 858 859 static const struct v4l2_ctrl_ops max9286_ctrl_ops = { 860 .s_ctrl = max9286_s_ctrl, 861 }; 862 863 static int max9286_v4l2_register(struct max9286_priv *priv) 864 { 865 struct device *dev = &priv->client->dev; 866 struct fwnode_handle *ep; 867 int ret; 868 int i; 869 870 /* Register v4l2 async notifiers for connected Camera subdevices */ 871 ret = max9286_v4l2_notifier_register(priv); 872 if (ret) { 873 dev_err(dev, "Unable to register V4L2 async notifiers\n"); 874 return ret; 875 } 876 877 /* Configure V4L2 for the MAX9286 itself */ 878 879 for (i = 0; i < MAX9286_N_SINKS; i++) 880 max9286_init_format(&priv->fmt[i]); 881 882 v4l2_i2c_subdev_init(&priv->sd, priv->client, &max9286_subdev_ops); 883 priv->sd.internal_ops = &max9286_subdev_internal_ops; 884 priv->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; 885 886 v4l2_ctrl_handler_init(&priv->ctrls, 1); 887 priv->pixelrate = v4l2_ctrl_new_std(&priv->ctrls, 888 &max9286_ctrl_ops, 889 V4L2_CID_PIXEL_RATE, 890 1, INT_MAX, 1, 50000000); 891 892 priv->sd.ctrl_handler = &priv->ctrls; 893 ret = priv->ctrls.error; 894 if (ret) 895 goto err_async; 896 897 priv->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE; 898 899 priv->pads[MAX9286_SRC_PAD].flags = MEDIA_PAD_FL_SOURCE; 900 for (i = 0; i < MAX9286_SRC_PAD; i++) 901 priv->pads[i].flags = MEDIA_PAD_FL_SINK; 902 ret = media_entity_pads_init(&priv->sd.entity, MAX9286_N_PADS, 903 priv->pads); 904 if (ret) 905 goto err_async; 906 907 ep = fwnode_graph_get_endpoint_by_id(dev_fwnode(dev), MAX9286_SRC_PAD, 908 0, 0); 909 if (!ep) { 910 dev_err(dev, "Unable to retrieve endpoint on \"port@4\"\n"); 911 ret = -ENOENT; 912 goto err_async; 913 } 914 priv->sd.fwnode = ep; 915 916 ret = v4l2_async_register_subdev(&priv->sd); 917 if (ret < 0) { 918 dev_err(dev, "Unable to register subdevice\n"); 919 goto err_put_node; 920 } 921 922 return 0; 923 924 err_put_node: 925 fwnode_handle_put(ep); 926 err_async: 927 max9286_v4l2_notifier_unregister(priv); 928 929 return ret; 930 } 931 932 static void max9286_v4l2_unregister(struct max9286_priv *priv) 933 { 934 fwnode_handle_put(priv->sd.fwnode); 935 v4l2_async_unregister_subdev(&priv->sd); 936 max9286_v4l2_notifier_unregister(priv); 937 } 938 939 /* ----------------------------------------------------------------------------- 940 * Probe/Remove 941 */ 942 943 static int max9286_setup(struct max9286_priv *priv) 944 { 945 /* 946 * Link ordering values for all enabled links combinations. Orders must 947 * be assigned sequentially from 0 to the number of enabled links 948 * without leaving any hole for disabled links. We thus assign orders to 949 * enabled links first, and use the remaining order values for disabled 950 * links are all links must have a different order value; 951 */ 952 static const u8 link_order[] = { 953 (3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* xxxx */ 954 (3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* xxx0 */ 955 (3 << 6) | (2 << 4) | (0 << 2) | (1 << 0), /* xx0x */ 956 (3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* xx10 */ 957 (3 << 6) | (0 << 4) | (2 << 2) | (1 << 0), /* x0xx */ 958 (3 << 6) | (1 << 4) | (2 << 2) | (0 << 0), /* x1x0 */ 959 (3 << 6) | (1 << 4) | (0 << 2) | (2 << 0), /* x10x */ 960 (3 << 6) | (1 << 4) | (1 << 2) | (0 << 0), /* x210 */ 961 (0 << 6) | (3 << 4) | (2 << 2) | (1 << 0), /* 0xxx */ 962 (1 << 6) | (3 << 4) | (2 << 2) | (0 << 0), /* 1xx0 */ 963 (1 << 6) | (3 << 4) | (0 << 2) | (2 << 0), /* 1x0x */ 964 (2 << 6) | (3 << 4) | (1 << 2) | (0 << 0), /* 2x10 */ 965 (1 << 6) | (0 << 4) | (3 << 2) | (2 << 0), /* 10xx */ 966 (2 << 6) | (1 << 4) | (3 << 2) | (0 << 0), /* 21x0 */ 967 (2 << 6) | (1 << 4) | (0 << 2) | (3 << 0), /* 210x */ 968 (3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* 3210 */ 969 }; 970 971 /* 972 * Set the I2C bus speed. 973 * 974 * Enable I2C Local Acknowledge during the probe sequences of the camera 975 * only. This should be disabled after the mux is initialised. 976 */ 977 max9286_configure_i2c(priv, true); 978 max9286_reverse_channel_setup(priv, priv->init_rev_chan_mv); 979 980 /* 981 * Enable GMSL links, mask unused ones and autodetect link 982 * used as CSI clock source. 983 */ 984 max9286_write(priv, 0x00, MAX9286_MSTLINKSEL_AUTO | priv->route_mask); 985 max9286_write(priv, 0x0b, link_order[priv->route_mask]); 986 max9286_write(priv, 0x69, (0xf & ~priv->route_mask)); 987 988 /* 989 * Video format setup: 990 * Disable CSI output, VC is set according to Link number. 991 */ 992 max9286_write(priv, 0x15, MAX9286_VCTYPE | MAX9286_0X15_RESV); 993 994 /* Enable CSI-2 Lane D0-D3 only, DBL mode, YUV422 8-bit. */ 995 max9286_write(priv, 0x12, MAX9286_CSIDBL | MAX9286_DBL | 996 MAX9286_CSILANECNT(priv->csi2_data_lanes) | 997 MAX9286_DATATYPE_YUV422_8BIT); 998 999 /* Automatic: FRAMESYNC taken from the slowest Link. */ 1000 max9286_write(priv, 0x01, MAX9286_FSYNCMODE_INT_HIZ | 1001 MAX9286_FSYNCMETH_AUTO); 1002 1003 /* Enable HS/VS encoding, use D14/15 for HS/VS, invert VS. */ 1004 max9286_write(priv, 0x0c, MAX9286_HVEN | MAX9286_INVVS | 1005 MAX9286_HVSRC_D14); 1006 1007 /* 1008 * The overlap window seems to provide additional validation by tracking 1009 * the delay between vsync and frame sync, generating an error if the 1010 * delay is bigger than the programmed window, though it's not yet clear 1011 * what value should be set. 1012 * 1013 * As it's an optional value and can be disabled, we do so by setting 1014 * a 0 overlap value. 1015 */ 1016 max9286_write(priv, 0x63, 0); 1017 max9286_write(priv, 0x64, 0); 1018 1019 /* 1020 * Wait for 2ms to allow the link to resynchronize after the 1021 * configuration change. 1022 */ 1023 usleep_range(2000, 5000); 1024 1025 return 0; 1026 } 1027 1028 static void max9286_gpio_set(struct gpio_chip *chip, 1029 unsigned int offset, int value) 1030 { 1031 struct max9286_priv *priv = gpiochip_get_data(chip); 1032 1033 if (value) 1034 priv->gpio_state |= BIT(offset); 1035 else 1036 priv->gpio_state &= ~BIT(offset); 1037 1038 max9286_write(priv, 0x0f, MAX9286_0X0F_RESERVED | priv->gpio_state); 1039 } 1040 1041 static int max9286_gpio_get(struct gpio_chip *chip, unsigned int offset) 1042 { 1043 struct max9286_priv *priv = gpiochip_get_data(chip); 1044 1045 return priv->gpio_state & BIT(offset); 1046 } 1047 1048 static int max9286_register_gpio(struct max9286_priv *priv) 1049 { 1050 struct device *dev = &priv->client->dev; 1051 struct gpio_chip *gpio = &priv->gpio; 1052 int ret; 1053 1054 /* Configure the GPIO */ 1055 gpio->label = dev_name(dev); 1056 gpio->parent = dev; 1057 gpio->owner = THIS_MODULE; 1058 gpio->ngpio = 2; 1059 gpio->base = -1; 1060 gpio->set = max9286_gpio_set; 1061 gpio->get = max9286_gpio_get; 1062 gpio->can_sleep = true; 1063 1064 /* GPIO values default to high */ 1065 priv->gpio_state = BIT(0) | BIT(1); 1066 1067 ret = devm_gpiochip_add_data(dev, gpio, priv); 1068 if (ret) 1069 dev_err(dev, "Unable to create gpio_chip\n"); 1070 1071 return ret; 1072 } 1073 1074 static int max9286_init(struct device *dev) 1075 { 1076 struct max9286_priv *priv; 1077 struct i2c_client *client; 1078 int ret; 1079 1080 client = to_i2c_client(dev); 1081 priv = i2c_get_clientdata(client); 1082 1083 /* Enable the bus power. */ 1084 ret = regulator_enable(priv->regulator); 1085 if (ret < 0) { 1086 dev_err(&client->dev, "Unable to turn PoC on\n"); 1087 return ret; 1088 } 1089 1090 ret = max9286_setup(priv); 1091 if (ret) { 1092 dev_err(dev, "Unable to setup max9286\n"); 1093 goto err_regulator; 1094 } 1095 1096 /* 1097 * Register all V4L2 interactions for the MAX9286 and notifiers for 1098 * any subdevices connected. 1099 */ 1100 ret = max9286_v4l2_register(priv); 1101 if (ret) { 1102 dev_err(dev, "Failed to register with V4L2\n"); 1103 goto err_regulator; 1104 } 1105 1106 ret = max9286_i2c_mux_init(priv); 1107 if (ret) { 1108 dev_err(dev, "Unable to initialize I2C multiplexer\n"); 1109 goto err_v4l2_register; 1110 } 1111 1112 /* Leave the mux channels disabled until they are selected. */ 1113 max9286_i2c_mux_close(priv); 1114 1115 return 0; 1116 1117 err_v4l2_register: 1118 max9286_v4l2_unregister(priv); 1119 err_regulator: 1120 regulator_disable(priv->regulator); 1121 1122 return ret; 1123 } 1124 1125 static void max9286_cleanup_dt(struct max9286_priv *priv) 1126 { 1127 struct max9286_source *source; 1128 1129 for_each_source(priv, source) { 1130 fwnode_handle_put(source->fwnode); 1131 source->fwnode = NULL; 1132 } 1133 } 1134 1135 static int max9286_parse_dt(struct max9286_priv *priv) 1136 { 1137 struct device *dev = &priv->client->dev; 1138 struct device_node *i2c_mux; 1139 struct device_node *node = NULL; 1140 unsigned int i2c_mux_mask = 0; 1141 u32 reverse_channel_microvolt; 1142 1143 /* Balance the of_node_put() performed by of_find_node_by_name(). */ 1144 of_node_get(dev->of_node); 1145 i2c_mux = of_find_node_by_name(dev->of_node, "i2c-mux"); 1146 if (!i2c_mux) { 1147 dev_err(dev, "Failed to find i2c-mux node\n"); 1148 return -EINVAL; 1149 } 1150 1151 /* Identify which i2c-mux channels are enabled */ 1152 for_each_child_of_node(i2c_mux, node) { 1153 u32 id = 0; 1154 1155 of_property_read_u32(node, "reg", &id); 1156 if (id >= MAX9286_NUM_GMSL) 1157 continue; 1158 1159 if (!of_device_is_available(node)) { 1160 dev_dbg(dev, "Skipping disabled I2C bus port %u\n", id); 1161 continue; 1162 } 1163 1164 i2c_mux_mask |= BIT(id); 1165 } 1166 of_node_put(node); 1167 of_node_put(i2c_mux); 1168 1169 /* Parse the endpoints */ 1170 for_each_endpoint_of_node(dev->of_node, node) { 1171 struct max9286_source *source; 1172 struct of_endpoint ep; 1173 1174 of_graph_parse_endpoint(node, &ep); 1175 dev_dbg(dev, "Endpoint %pOF on port %d", 1176 ep.local_node, ep.port); 1177 1178 if (ep.port > MAX9286_NUM_GMSL) { 1179 dev_err(dev, "Invalid endpoint %s on port %d", 1180 of_node_full_name(ep.local_node), ep.port); 1181 continue; 1182 } 1183 1184 /* For the source endpoint just parse the bus configuration. */ 1185 if (ep.port == MAX9286_SRC_PAD) { 1186 struct v4l2_fwnode_endpoint vep = { 1187 .bus_type = V4L2_MBUS_CSI2_DPHY 1188 }; 1189 int ret; 1190 1191 ret = v4l2_fwnode_endpoint_parse( 1192 of_fwnode_handle(node), &vep); 1193 if (ret) { 1194 of_node_put(node); 1195 return ret; 1196 } 1197 1198 priv->csi2_data_lanes = 1199 vep.bus.mipi_csi2.num_data_lanes; 1200 1201 continue; 1202 } 1203 1204 /* Skip if the corresponding GMSL link is unavailable. */ 1205 if (!(i2c_mux_mask & BIT(ep.port))) 1206 continue; 1207 1208 if (priv->sources[ep.port].fwnode) { 1209 dev_err(dev, 1210 "Multiple port endpoints are not supported: %d", 1211 ep.port); 1212 1213 continue; 1214 } 1215 1216 source = &priv->sources[ep.port]; 1217 source->fwnode = fwnode_graph_get_remote_endpoint( 1218 of_fwnode_handle(node)); 1219 if (!source->fwnode) { 1220 dev_err(dev, 1221 "Endpoint %pOF has no remote endpoint connection\n", 1222 ep.local_node); 1223 1224 continue; 1225 } 1226 1227 priv->source_mask |= BIT(ep.port); 1228 priv->nsources++; 1229 } 1230 of_node_put(node); 1231 1232 /* 1233 * Parse the initial value of the reverse channel amplitude from 1234 * the firmware interface and convert it to millivolts. 1235 * 1236 * Default it to 170mV for backward compatibility with DTBs that do not 1237 * provide the property. 1238 */ 1239 if (of_property_read_u32(dev->of_node, 1240 "maxim,reverse-channel-microvolt", 1241 &reverse_channel_microvolt)) 1242 priv->init_rev_chan_mv = 170; 1243 else 1244 priv->init_rev_chan_mv = reverse_channel_microvolt / 1000U; 1245 1246 priv->route_mask = priv->source_mask; 1247 1248 return 0; 1249 } 1250 1251 static int max9286_probe(struct i2c_client *client) 1252 { 1253 struct max9286_priv *priv; 1254 int ret; 1255 1256 priv = devm_kzalloc(&client->dev, sizeof(*priv), GFP_KERNEL); 1257 if (!priv) 1258 return -ENOMEM; 1259 1260 mutex_init(&priv->mutex); 1261 1262 priv->client = client; 1263 i2c_set_clientdata(client, priv); 1264 1265 priv->gpiod_pwdn = devm_gpiod_get_optional(&client->dev, "enable", 1266 GPIOD_OUT_HIGH); 1267 if (IS_ERR(priv->gpiod_pwdn)) 1268 return PTR_ERR(priv->gpiod_pwdn); 1269 1270 gpiod_set_consumer_name(priv->gpiod_pwdn, "max9286-pwdn"); 1271 gpiod_set_value_cansleep(priv->gpiod_pwdn, 1); 1272 1273 /* Wait at least 4ms before the I2C lines latch to the address */ 1274 if (priv->gpiod_pwdn) 1275 usleep_range(4000, 5000); 1276 1277 /* 1278 * The MAX9286 starts by default with all ports enabled, we disable all 1279 * ports early to ensure that all channels are disabled if we error out 1280 * and keep the bus consistent. 1281 */ 1282 max9286_i2c_mux_close(priv); 1283 1284 /* 1285 * The MAX9286 initialises with auto-acknowledge enabled by default. 1286 * This can be invasive to other transactions on the same bus, so 1287 * disable it early. It will be enabled only as and when needed. 1288 */ 1289 max9286_configure_i2c(priv, false); 1290 1291 ret = max9286_register_gpio(priv); 1292 if (ret) 1293 goto err_powerdown; 1294 1295 priv->regulator = devm_regulator_get(&client->dev, "poc"); 1296 if (IS_ERR(priv->regulator)) { 1297 ret = PTR_ERR(priv->regulator); 1298 dev_err_probe(&client->dev, ret, 1299 "Unable to get PoC regulator\n"); 1300 goto err_powerdown; 1301 } 1302 1303 ret = max9286_parse_dt(priv); 1304 if (ret) 1305 goto err_powerdown; 1306 1307 ret = max9286_init(&client->dev); 1308 if (ret < 0) 1309 goto err_cleanup_dt; 1310 1311 return 0; 1312 1313 err_cleanup_dt: 1314 max9286_cleanup_dt(priv); 1315 err_powerdown: 1316 gpiod_set_value_cansleep(priv->gpiod_pwdn, 0); 1317 1318 return ret; 1319 } 1320 1321 static int max9286_remove(struct i2c_client *client) 1322 { 1323 struct max9286_priv *priv = i2c_get_clientdata(client); 1324 1325 i2c_mux_del_adapters(priv->mux); 1326 1327 max9286_v4l2_unregister(priv); 1328 1329 regulator_disable(priv->regulator); 1330 1331 gpiod_set_value_cansleep(priv->gpiod_pwdn, 0); 1332 1333 max9286_cleanup_dt(priv); 1334 1335 return 0; 1336 } 1337 1338 static const struct of_device_id max9286_dt_ids[] = { 1339 { .compatible = "maxim,max9286" }, 1340 {}, 1341 }; 1342 MODULE_DEVICE_TABLE(of, max9286_dt_ids); 1343 1344 static struct i2c_driver max9286_i2c_driver = { 1345 .driver = { 1346 .name = "max9286", 1347 .of_match_table = of_match_ptr(max9286_dt_ids), 1348 }, 1349 .probe_new = max9286_probe, 1350 .remove = max9286_remove, 1351 }; 1352 1353 module_i2c_driver(max9286_i2c_driver); 1354 1355 MODULE_DESCRIPTION("Maxim MAX9286 GMSL Deserializer Driver"); 1356 MODULE_AUTHOR("Jacopo Mondi, Kieran Bingham, Laurent Pinchart, Niklas Söderlund, Vladimir Barinov"); 1357 MODULE_LICENSE("GPL"); 1358