1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 cx24110 - Single Chip Satellite Channel Receiver driver module
4
5 Copyright (C) 2002 Peter Hettkamp <peter.hettkamp@htp-tel.de> based on
6 work
7 Copyright (C) 1999 Convergence Integrated Media GmbH <ralph@convergence.de>
8
9
10 */
11
12 #include <linux/slab.h>
13 #include <linux/kernel.h>
14 #include <linux/module.h>
15 #include <linux/init.h>
16
17 #include <media/dvb_frontend.h>
18 #include "cx24110.h"
19
20
21 struct cx24110_state {
22
23 struct i2c_adapter* i2c;
24
25 const struct cx24110_config* config;
26
27 struct dvb_frontend frontend;
28
29 u32 lastber;
30 u32 lastbler;
31 u32 lastesn0;
32 };
33
34 static int debug;
35 #define dprintk(args...) \
36 do { \
37 if (debug) printk(KERN_DEBUG "cx24110: " args); \
38 } while (0)
39
40 static struct {u8 reg; u8 data;} cx24110_regdata[]=
41 /* Comments beginning with @ denote this value should
42 be the default */
43 {{0x09,0x01}, /* SoftResetAll */
44 {0x09,0x00}, /* release reset */
45 {0x01,0xe8}, /* MSB of code rate 27.5MS/s */
46 {0x02,0x17}, /* middle byte " */
47 {0x03,0x29}, /* LSB " */
48 {0x05,0x03}, /* @ DVB mode, standard code rate 3/4 */
49 {0x06,0xa5}, /* @ PLL 60MHz */
50 {0x07,0x01}, /* @ Fclk, i.e. sampling clock, 60MHz */
51 {0x0a,0x00}, /* @ partial chip disables, do not set */
52 {0x0b,0x01}, /* set output clock in gapped mode, start signal low
53 active for first byte */
54 {0x0c,0x11}, /* no parity bytes, large hold time, serial data out */
55 {0x0d,0x6f}, /* @ RS Sync/Unsync thresholds */
56 {0x10,0x40}, /* chip doc is misleading here: write bit 6 as 1
57 to avoid starting the BER counter. Reset the
58 CRC test bit. Finite counting selected */
59 {0x15,0xff}, /* @ size of the limited time window for RS BER
60 estimation. It is <value>*256 RS blocks, this
61 gives approx. 2.6 sec at 27.5MS/s, rate 3/4 */
62 {0x16,0x00}, /* @ enable all RS output ports */
63 {0x17,0x04}, /* @ time window allowed for the RS to sync */
64 {0x18,0xae}, /* @ allow all standard DVB code rates to be scanned
65 for automatically */
66 /* leave the current code rate and normalization
67 registers as they are after reset... */
68 {0x21,0x10}, /* @ during AutoAcq, search each viterbi setting
69 only once */
70 {0x23,0x18}, /* @ size of the limited time window for Viterbi BER
71 estimation. It is <value>*65536 channel bits, i.e.
72 approx. 38ms at 27.5MS/s, rate 3/4 */
73 {0x24,0x24}, /* do not trigger Viterbi CRC test. Finite count window */
74 /* leave front-end AGC parameters at default values */
75 /* leave decimation AGC parameters at default values */
76 {0x35,0x40}, /* disable all interrupts. They are not connected anyway */
77 {0x36,0xff}, /* clear all interrupt pending flags */
78 {0x37,0x00}, /* @ fully enable AutoAcqq state machine */
79 {0x38,0x07}, /* @ enable fade recovery, but not autostart AutoAcq */
80 /* leave the equalizer parameters on their default values */
81 /* leave the final AGC parameters on their default values */
82 {0x41,0x00}, /* @ MSB of front-end derotator frequency */
83 {0x42,0x00}, /* @ middle bytes " */
84 {0x43,0x00}, /* @ LSB " */
85 /* leave the carrier tracking loop parameters on default */
86 /* leave the bit timing loop parameters at default */
87 {0x56,0x4d}, /* set the filtune voltage to 2.7V, as recommended by */
88 /* the cx24108 data sheet for symbol rates above 15MS/s */
89 {0x57,0x00}, /* @ Filter sigma delta enabled, positive */
90 {0x61,0x95}, /* GPIO pins 1-4 have special function */
91 {0x62,0x05}, /* GPIO pin 5 has special function, pin 6 is GPIO */
92 {0x63,0x00}, /* All GPIO pins use CMOS output characteristics */
93 {0x64,0x20}, /* GPIO 6 is input, all others are outputs */
94 {0x6d,0x30}, /* tuner auto mode clock freq 62kHz */
95 {0x70,0x15}, /* use auto mode, tuner word is 21 bits long */
96 {0x73,0x00}, /* @ disable several demod bypasses */
97 {0x74,0x00}, /* @ " */
98 {0x75,0x00} /* @ " */
99 /* the remaining registers are for SEC */
100 };
101
102
cx24110_writereg(struct cx24110_state * state,int reg,int data)103 static int cx24110_writereg (struct cx24110_state* state, int reg, int data)
104 {
105 u8 buf [] = { reg, data };
106 struct i2c_msg msg = { .addr = state->config->demod_address, .flags = 0, .buf = buf, .len = 2 };
107 int err;
108
109 if ((err = i2c_transfer(state->i2c, &msg, 1)) != 1) {
110 dprintk("%s: writereg error (err == %i, reg == 0x%02x, data == 0x%02x)\n",
111 __func__, err, reg, data);
112 return -EREMOTEIO;
113 }
114
115 return 0;
116 }
117
cx24110_readreg(struct cx24110_state * state,u8 reg)118 static int cx24110_readreg (struct cx24110_state* state, u8 reg)
119 {
120 int ret;
121 u8 b0 [] = { reg };
122 u8 b1 [] = { 0 };
123 struct i2c_msg msg [] = { { .addr = state->config->demod_address, .flags = 0, .buf = b0, .len = 1 },
124 { .addr = state->config->demod_address, .flags = I2C_M_RD, .buf = b1, .len = 1 } };
125
126 ret = i2c_transfer(state->i2c, msg, 2);
127
128 if (ret != 2) return ret;
129
130 return b1[0];
131 }
132
cx24110_set_inversion(struct cx24110_state * state,enum fe_spectral_inversion inversion)133 static int cx24110_set_inversion(struct cx24110_state *state,
134 enum fe_spectral_inversion inversion)
135 {
136 /* fixme (low): error handling */
137
138 switch (inversion) {
139 case INVERSION_OFF:
140 cx24110_writereg(state,0x37,cx24110_readreg(state,0x37)|0x1);
141 /* AcqSpectrInvDis on. No idea why someone should want this */
142 cx24110_writereg(state,0x5,cx24110_readreg(state,0x5)&0xf7);
143 /* Initial value 0 at start of acq */
144 cx24110_writereg(state,0x22,cx24110_readreg(state,0x22)&0xef);
145 /* current value 0 */
146 /* The cx24110 manual tells us this reg is read-only.
147 But what the heck... set it ayways */
148 break;
149 case INVERSION_ON:
150 cx24110_writereg(state,0x37,cx24110_readreg(state,0x37)|0x1);
151 /* AcqSpectrInvDis on. No idea why someone should want this */
152 cx24110_writereg(state,0x5,cx24110_readreg(state,0x5)|0x08);
153 /* Initial value 1 at start of acq */
154 cx24110_writereg(state,0x22,cx24110_readreg(state,0x22)|0x10);
155 /* current value 1 */
156 break;
157 case INVERSION_AUTO:
158 cx24110_writereg(state,0x37,cx24110_readreg(state,0x37)&0xfe);
159 /* AcqSpectrInvDis off. Leave initial & current states as is */
160 break;
161 default:
162 return -EINVAL;
163 }
164
165 return 0;
166 }
167
cx24110_set_fec(struct cx24110_state * state,enum fe_code_rate fec)168 static int cx24110_set_fec(struct cx24110_state *state, enum fe_code_rate fec)
169 {
170 static const int rate[FEC_AUTO] = {-1, 1, 2, 3, 5, 7, -1};
171 static const int g1[FEC_AUTO] = {-1, 0x01, 0x02, 0x05, 0x15, 0x45, -1};
172 static const int g2[FEC_AUTO] = {-1, 0x01, 0x03, 0x06, 0x1a, 0x7a, -1};
173
174 /* Well, the AutoAcq engine of the cx24106 and 24110 automatically
175 searches all enabled viterbi rates, and can handle non-standard
176 rates as well. */
177
178 if (fec > FEC_AUTO)
179 fec = FEC_AUTO;
180
181 if (fec == FEC_AUTO) { /* (re-)establish AutoAcq behaviour */
182 cx24110_writereg(state, 0x37, cx24110_readreg(state, 0x37) & 0xdf);
183 /* clear AcqVitDis bit */
184 cx24110_writereg(state, 0x18, 0xae);
185 /* allow all DVB standard code rates */
186 cx24110_writereg(state, 0x05, (cx24110_readreg(state, 0x05) & 0xf0) | 0x3);
187 /* set nominal Viterbi rate 3/4 */
188 cx24110_writereg(state, 0x22, (cx24110_readreg(state, 0x22) & 0xf0) | 0x3);
189 /* set current Viterbi rate 3/4 */
190 cx24110_writereg(state, 0x1a, 0x05);
191 cx24110_writereg(state, 0x1b, 0x06);
192 /* set the puncture registers for code rate 3/4 */
193 return 0;
194 } else {
195 cx24110_writereg(state, 0x37, cx24110_readreg(state, 0x37) | 0x20);
196 /* set AcqVitDis bit */
197 if (rate[fec] < 0)
198 return -EINVAL;
199
200 cx24110_writereg(state, 0x05, (cx24110_readreg(state, 0x05) & 0xf0) | rate[fec]);
201 /* set nominal Viterbi rate */
202 cx24110_writereg(state, 0x22, (cx24110_readreg(state, 0x22) & 0xf0) | rate[fec]);
203 /* set current Viterbi rate */
204 cx24110_writereg(state, 0x1a, g1[fec]);
205 cx24110_writereg(state, 0x1b, g2[fec]);
206 /* not sure if this is the right way: I always used AutoAcq mode */
207 }
208 return 0;
209 }
210
cx24110_get_fec(struct cx24110_state * state)211 static enum fe_code_rate cx24110_get_fec(struct cx24110_state *state)
212 {
213 int i;
214
215 i=cx24110_readreg(state,0x22)&0x0f;
216 if(!(i&0x08)) {
217 return FEC_1_2 + i - 1;
218 } else {
219 /* fixme (low): a special code rate has been selected. In theory, we need to
220 return a denominator value, a numerator value, and a pair of puncture
221 maps to correctly describe this mode. But this should never happen in
222 practice, because it cannot be set by cx24110_get_fec. */
223 return FEC_NONE;
224 }
225 }
226
cx24110_set_symbolrate(struct cx24110_state * state,u32 srate)227 static int cx24110_set_symbolrate (struct cx24110_state* state, u32 srate)
228 {
229 /* fixme (low): add error handling */
230 u32 ratio;
231 u32 tmp, fclk, BDRI;
232
233 static const u32 bands[]={5000000UL,15000000UL,90999000UL/2};
234 int i;
235
236 dprintk("cx24110 debug: entering %s(%d)\n",__func__,srate);
237 if (srate>90999000UL/2)
238 srate=90999000UL/2;
239 if (srate<500000)
240 srate=500000;
241
242 for(i = 0; (i < ARRAY_SIZE(bands)) && (srate>bands[i]); i++)
243 ;
244 /* first, check which sample rate is appropriate: 45, 60 80 or 90 MHz,
245 and set the PLL accordingly (R07[1:0] Fclk, R06[7:4] PLLmult,
246 R06[3:0] PLLphaseDetGain */
247 tmp=cx24110_readreg(state,0x07)&0xfc;
248 if(srate<90999000UL/4) { /* sample rate 45MHz*/
249 cx24110_writereg(state,0x07,tmp);
250 cx24110_writereg(state,0x06,0x78);
251 fclk=90999000UL/2;
252 } else if(srate<60666000UL/2) { /* sample rate 60MHz */
253 cx24110_writereg(state,0x07,tmp|0x1);
254 cx24110_writereg(state,0x06,0xa5);
255 fclk=60666000UL;
256 } else if(srate<80888000UL/2) { /* sample rate 80MHz */
257 cx24110_writereg(state,0x07,tmp|0x2);
258 cx24110_writereg(state,0x06,0x87);
259 fclk=80888000UL;
260 } else { /* sample rate 90MHz */
261 cx24110_writereg(state,0x07,tmp|0x3);
262 cx24110_writereg(state,0x06,0x78);
263 fclk=90999000UL;
264 }
265 dprintk("cx24110 debug: fclk %d Hz\n",fclk);
266 /* we need to divide two integers with approx. 27 bits in 32 bit
267 arithmetic giving a 25 bit result */
268 /* the maximum dividend is 90999000/2, 0x02b6446c, this number is
269 also the most complex divisor. Hence, the dividend has,
270 assuming 32bit unsigned arithmetic, 6 clear bits on top, the
271 divisor 2 unused bits at the bottom. Also, the quotient is
272 always less than 1/2. Borrowed from VES1893.c, of course */
273
274 tmp=srate<<6;
275 BDRI=fclk>>2;
276 ratio=(tmp/BDRI);
277
278 tmp=(tmp%BDRI)<<8;
279 ratio=(ratio<<8)+(tmp/BDRI);
280
281 tmp=(tmp%BDRI)<<8;
282 ratio=(ratio<<8)+(tmp/BDRI);
283
284 tmp=(tmp%BDRI)<<1;
285 ratio=(ratio<<1)+(tmp/BDRI);
286
287 dprintk("srate= %d (range %d, up to %d)\n", srate,i,bands[i]);
288 dprintk("fclk = %d\n", fclk);
289 dprintk("ratio= %08x\n", ratio);
290
291 cx24110_writereg(state, 0x1, (ratio>>16)&0xff);
292 cx24110_writereg(state, 0x2, (ratio>>8)&0xff);
293 cx24110_writereg(state, 0x3, (ratio)&0xff);
294
295 return 0;
296
297 }
298
_cx24110_pll_write(struct dvb_frontend * fe,const u8 buf[],int len)299 static int _cx24110_pll_write (struct dvb_frontend* fe, const u8 buf[], int len)
300 {
301 struct cx24110_state *state = fe->demodulator_priv;
302
303 if (len != 3)
304 return -EINVAL;
305
306 /* tuner data is 21 bits long, must be left-aligned in data */
307 /* tuner cx24108 is written through a dedicated 3wire interface on the demod chip */
308 /* FIXME (low): add error handling, avoid infinite loops if HW fails... */
309
310 cx24110_writereg(state,0x6d,0x30); /* auto mode at 62kHz */
311 cx24110_writereg(state,0x70,0x15); /* auto mode 21 bits */
312
313 /* if the auto tuner writer is still busy, clear it out */
314 while (cx24110_readreg(state,0x6d)&0x80)
315 cx24110_writereg(state,0x72,0);
316
317 /* write the topmost 8 bits */
318 cx24110_writereg(state,0x72,buf[0]);
319
320 /* wait for the send to be completed */
321 while ((cx24110_readreg(state,0x6d)&0xc0)==0x80)
322 ;
323
324 /* send another 8 bytes */
325 cx24110_writereg(state,0x72,buf[1]);
326 while ((cx24110_readreg(state,0x6d)&0xc0)==0x80)
327 ;
328
329 /* and the topmost 5 bits of this byte */
330 cx24110_writereg(state,0x72,buf[2]);
331 while ((cx24110_readreg(state,0x6d)&0xc0)==0x80)
332 ;
333
334 /* now strobe the enable line once */
335 cx24110_writereg(state,0x6d,0x32);
336 cx24110_writereg(state,0x6d,0x30);
337
338 return 0;
339 }
340
cx24110_initfe(struct dvb_frontend * fe)341 static int cx24110_initfe(struct dvb_frontend* fe)
342 {
343 struct cx24110_state *state = fe->demodulator_priv;
344 /* fixme (low): error handling */
345 int i;
346
347 dprintk("%s: init chip\n", __func__);
348
349 for(i = 0; i < ARRAY_SIZE(cx24110_regdata); i++) {
350 cx24110_writereg(state, cx24110_regdata[i].reg, cx24110_regdata[i].data);
351 }
352
353 return 0;
354 }
355
cx24110_set_voltage(struct dvb_frontend * fe,enum fe_sec_voltage voltage)356 static int cx24110_set_voltage(struct dvb_frontend *fe,
357 enum fe_sec_voltage voltage)
358 {
359 struct cx24110_state *state = fe->demodulator_priv;
360
361 switch (voltage) {
362 case SEC_VOLTAGE_13:
363 return cx24110_writereg(state,0x76,(cx24110_readreg(state,0x76)&0x3b)|0xc0);
364 case SEC_VOLTAGE_18:
365 return cx24110_writereg(state,0x76,(cx24110_readreg(state,0x76)&0x3b)|0x40);
366 default:
367 return -EINVAL;
368 }
369 }
370
cx24110_diseqc_send_burst(struct dvb_frontend * fe,enum fe_sec_mini_cmd burst)371 static int cx24110_diseqc_send_burst(struct dvb_frontend *fe,
372 enum fe_sec_mini_cmd burst)
373 {
374 int rv, bit;
375 struct cx24110_state *state = fe->demodulator_priv;
376 unsigned long timeout;
377
378 if (burst == SEC_MINI_A)
379 bit = 0x00;
380 else if (burst == SEC_MINI_B)
381 bit = 0x08;
382 else
383 return -EINVAL;
384
385 rv = cx24110_readreg(state, 0x77);
386 if (!(rv & 0x04))
387 cx24110_writereg(state, 0x77, rv | 0x04);
388
389 rv = cx24110_readreg(state, 0x76);
390 cx24110_writereg(state, 0x76, ((rv & 0x90) | 0x40 | bit));
391 timeout = jiffies + msecs_to_jiffies(100);
392 while (!time_after(jiffies, timeout) && !(cx24110_readreg(state, 0x76) & 0x40))
393 ; /* wait for LNB ready */
394
395 return 0;
396 }
397
cx24110_send_diseqc_msg(struct dvb_frontend * fe,struct dvb_diseqc_master_cmd * cmd)398 static int cx24110_send_diseqc_msg(struct dvb_frontend* fe,
399 struct dvb_diseqc_master_cmd *cmd)
400 {
401 int i, rv;
402 struct cx24110_state *state = fe->demodulator_priv;
403 unsigned long timeout;
404
405 if (cmd->msg_len < 3 || cmd->msg_len > 6)
406 return -EINVAL; /* not implemented */
407
408 for (i = 0; i < cmd->msg_len; i++)
409 cx24110_writereg(state, 0x79 + i, cmd->msg[i]);
410
411 rv = cx24110_readreg(state, 0x77);
412 if (rv & 0x04) {
413 cx24110_writereg(state, 0x77, rv & ~0x04);
414 msleep(30); /* reportedly fixes switching problems */
415 }
416
417 rv = cx24110_readreg(state, 0x76);
418
419 cx24110_writereg(state, 0x76, ((rv & 0x90) | 0x40) | ((cmd->msg_len-3) & 3));
420 timeout = jiffies + msecs_to_jiffies(100);
421 while (!time_after(jiffies, timeout) && !(cx24110_readreg(state, 0x76) & 0x40))
422 ; /* wait for LNB ready */
423
424 return 0;
425 }
426
cx24110_read_status(struct dvb_frontend * fe,enum fe_status * status)427 static int cx24110_read_status(struct dvb_frontend *fe,
428 enum fe_status *status)
429 {
430 struct cx24110_state *state = fe->demodulator_priv;
431
432 int sync = cx24110_readreg (state, 0x55);
433
434 *status = 0;
435
436 if (sync & 0x10)
437 *status |= FE_HAS_SIGNAL;
438
439 if (sync & 0x08)
440 *status |= FE_HAS_CARRIER;
441
442 sync = cx24110_readreg (state, 0x08);
443
444 if (sync & 0x40)
445 *status |= FE_HAS_VITERBI;
446
447 if (sync & 0x20)
448 *status |= FE_HAS_SYNC;
449
450 if ((sync & 0x60) == 0x60)
451 *status |= FE_HAS_LOCK;
452
453 return 0;
454 }
455
cx24110_read_ber(struct dvb_frontend * fe,u32 * ber)456 static int cx24110_read_ber(struct dvb_frontend* fe, u32* ber)
457 {
458 struct cx24110_state *state = fe->demodulator_priv;
459
460 /* fixme (maybe): value range is 16 bit. Scale? */
461 if(cx24110_readreg(state,0x24)&0x10) {
462 /* the Viterbi error counter has finished one counting window */
463 cx24110_writereg(state,0x24,0x04); /* select the ber reg */
464 state->lastber=cx24110_readreg(state,0x25)|
465 (cx24110_readreg(state,0x26)<<8);
466 cx24110_writereg(state,0x24,0x04); /* start new count window */
467 cx24110_writereg(state,0x24,0x14);
468 }
469 *ber = state->lastber;
470
471 return 0;
472 }
473
cx24110_read_signal_strength(struct dvb_frontend * fe,u16 * signal_strength)474 static int cx24110_read_signal_strength(struct dvb_frontend* fe, u16* signal_strength)
475 {
476 struct cx24110_state *state = fe->demodulator_priv;
477
478 /* no provision in hardware. Read the frontend AGC accumulator. No idea how to scale this, but I know it is 2s complement */
479 u8 signal = cx24110_readreg (state, 0x27)+128;
480 *signal_strength = (signal << 8) | signal;
481
482 return 0;
483 }
484
cx24110_read_snr(struct dvb_frontend * fe,u16 * snr)485 static int cx24110_read_snr(struct dvb_frontend* fe, u16* snr)
486 {
487 struct cx24110_state *state = fe->demodulator_priv;
488
489 /* no provision in hardware. Can be computed from the Es/N0 estimator, but I don't know how. */
490 if(cx24110_readreg(state,0x6a)&0x80) {
491 /* the Es/N0 error counter has finished one counting window */
492 state->lastesn0=cx24110_readreg(state,0x69)|
493 (cx24110_readreg(state,0x68)<<8);
494 cx24110_writereg(state,0x6a,0x84); /* start new count window */
495 }
496 *snr = state->lastesn0;
497
498 return 0;
499 }
500
cx24110_read_ucblocks(struct dvb_frontend * fe,u32 * ucblocks)501 static int cx24110_read_ucblocks(struct dvb_frontend* fe, u32* ucblocks)
502 {
503 struct cx24110_state *state = fe->demodulator_priv;
504
505 if(cx24110_readreg(state,0x10)&0x40) {
506 /* the RS error counter has finished one counting window */
507 cx24110_writereg(state,0x10,0x60); /* select the byer reg */
508 (void)(cx24110_readreg(state, 0x12) |
509 (cx24110_readreg(state, 0x13) << 8) |
510 (cx24110_readreg(state, 0x14) << 16));
511 cx24110_writereg(state,0x10,0x70); /* select the bler reg */
512 state->lastbler=cx24110_readreg(state,0x12)|
513 (cx24110_readreg(state,0x13)<<8)|
514 (cx24110_readreg(state,0x14)<<16);
515 cx24110_writereg(state,0x10,0x20); /* start new count window */
516 }
517 *ucblocks = state->lastbler;
518
519 return 0;
520 }
521
cx24110_set_frontend(struct dvb_frontend * fe)522 static int cx24110_set_frontend(struct dvb_frontend *fe)
523 {
524 struct cx24110_state *state = fe->demodulator_priv;
525 struct dtv_frontend_properties *p = &fe->dtv_property_cache;
526
527 if (fe->ops.tuner_ops.set_params) {
528 fe->ops.tuner_ops.set_params(fe);
529 if (fe->ops.i2c_gate_ctrl) fe->ops.i2c_gate_ctrl(fe, 0);
530 }
531
532 cx24110_set_inversion(state, p->inversion);
533 cx24110_set_fec(state, p->fec_inner);
534 cx24110_set_symbolrate(state, p->symbol_rate);
535 cx24110_writereg(state,0x04,0x05); /* start acquisition */
536
537 return 0;
538 }
539
cx24110_get_frontend(struct dvb_frontend * fe,struct dtv_frontend_properties * p)540 static int cx24110_get_frontend(struct dvb_frontend *fe,
541 struct dtv_frontend_properties *p)
542 {
543 struct cx24110_state *state = fe->demodulator_priv;
544 s32 afc; unsigned sclk;
545
546 /* cannot read back tuner settings (freq). Need to have some private storage */
547
548 sclk = cx24110_readreg (state, 0x07) & 0x03;
549 /* ok, real AFC (FEDR) freq. is afc/2^24*fsamp, fsamp=45/60/80/90MHz.
550 * Need 64 bit arithmetic. Is thiss possible in the kernel? */
551 if (sclk==0) sclk=90999000L/2L;
552 else if (sclk==1) sclk=60666000L;
553 else if (sclk==2) sclk=80888000L;
554 else sclk=90999000L;
555 sclk>>=8;
556 afc = sclk*(cx24110_readreg (state, 0x44)&0x1f)+
557 ((sclk*cx24110_readreg (state, 0x45))>>8)+
558 ((sclk*cx24110_readreg (state, 0x46))>>16);
559
560 p->frequency += afc;
561 p->inversion = (cx24110_readreg (state, 0x22) & 0x10) ?
562 INVERSION_ON : INVERSION_OFF;
563 p->fec_inner = cx24110_get_fec(state);
564
565 return 0;
566 }
567
cx24110_set_tone(struct dvb_frontend * fe,enum fe_sec_tone_mode tone)568 static int cx24110_set_tone(struct dvb_frontend *fe,
569 enum fe_sec_tone_mode tone)
570 {
571 struct cx24110_state *state = fe->demodulator_priv;
572
573 return cx24110_writereg(state,0x76,(cx24110_readreg(state,0x76)&~0x10)|(((tone==SEC_TONE_ON))?0x10:0));
574 }
575
cx24110_release(struct dvb_frontend * fe)576 static void cx24110_release(struct dvb_frontend* fe)
577 {
578 struct cx24110_state* state = fe->demodulator_priv;
579 kfree(state);
580 }
581
582 static const struct dvb_frontend_ops cx24110_ops;
583
cx24110_attach(const struct cx24110_config * config,struct i2c_adapter * i2c)584 struct dvb_frontend* cx24110_attach(const struct cx24110_config* config,
585 struct i2c_adapter* i2c)
586 {
587 struct cx24110_state* state = NULL;
588 int ret;
589
590 /* allocate memory for the internal state */
591 state = kzalloc(sizeof(struct cx24110_state), GFP_KERNEL);
592 if (state == NULL) goto error;
593
594 /* setup the state */
595 state->config = config;
596 state->i2c = i2c;
597 state->lastber = 0;
598 state->lastbler = 0;
599 state->lastesn0 = 0;
600
601 /* check if the demod is there */
602 ret = cx24110_readreg(state, 0x00);
603 if ((ret != 0x5a) && (ret != 0x69)) goto error;
604
605 /* create dvb_frontend */
606 memcpy(&state->frontend.ops, &cx24110_ops, sizeof(struct dvb_frontend_ops));
607 state->frontend.demodulator_priv = state;
608 return &state->frontend;
609
610 error:
611 kfree(state);
612 return NULL;
613 }
614
615 static const struct dvb_frontend_ops cx24110_ops = {
616 .delsys = { SYS_DVBS },
617 .info = {
618 .name = "Conexant CX24110 DVB-S",
619 .frequency_min_hz = 950 * MHz,
620 .frequency_max_hz = 2150 * MHz,
621 .frequency_stepsize_hz = 1011 * kHz,
622 .frequency_tolerance_hz = 29500 * kHz,
623 .symbol_rate_min = 1000000,
624 .symbol_rate_max = 45000000,
625 .caps = FE_CAN_INVERSION_AUTO |
626 FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 | FE_CAN_FEC_3_4 |
627 FE_CAN_FEC_5_6 | FE_CAN_FEC_7_8 | FE_CAN_FEC_AUTO |
628 FE_CAN_QPSK | FE_CAN_RECOVER
629 },
630
631 .release = cx24110_release,
632
633 .init = cx24110_initfe,
634 .write = _cx24110_pll_write,
635 .set_frontend = cx24110_set_frontend,
636 .get_frontend = cx24110_get_frontend,
637 .read_status = cx24110_read_status,
638 .read_ber = cx24110_read_ber,
639 .read_signal_strength = cx24110_read_signal_strength,
640 .read_snr = cx24110_read_snr,
641 .read_ucblocks = cx24110_read_ucblocks,
642
643 .diseqc_send_master_cmd = cx24110_send_diseqc_msg,
644 .set_tone = cx24110_set_tone,
645 .set_voltage = cx24110_set_voltage,
646 .diseqc_send_burst = cx24110_diseqc_send_burst,
647 };
648
649 module_param(debug, int, 0644);
650 MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off).");
651
652 MODULE_DESCRIPTION("Conexant CX24110 DVB-S Demodulator driver");
653 MODULE_AUTHOR("Peter Hettkamp");
654 MODULE_LICENSE("GPL");
655
656 EXPORT_SYMBOL_GPL(cx24110_attach);
657