1 /* SPDX-License-Identifier: GPL-2.0 */ 2 #ifndef _RAID1_H 3 #define _RAID1_H 4 5 /* 6 * each barrier unit size is 64MB fow now 7 * note: it must be larger than RESYNC_DEPTH 8 */ 9 #define BARRIER_UNIT_SECTOR_BITS 17 10 #define BARRIER_UNIT_SECTOR_SIZE (1<<17) 11 /* 12 * In struct r1conf, the following members are related to I/O barrier 13 * buckets, 14 * atomic_t *nr_pending; 15 * atomic_t *nr_waiting; 16 * atomic_t *nr_queued; 17 * atomic_t *barrier; 18 * Each of them points to array of atomic_t variables, each array is 19 * designed to have BARRIER_BUCKETS_NR elements and occupy a single 20 * memory page. The data width of atomic_t variables is 4 bytes, equal 21 * to 1<<(ilog2(sizeof(atomic_t))), BARRIER_BUCKETS_NR_BITS is defined 22 * as (PAGE_SHIFT - ilog2(sizeof(int))) to make sure an array of 23 * atomic_t variables with BARRIER_BUCKETS_NR elements just exactly 24 * occupies a single memory page. 25 */ 26 #define BARRIER_BUCKETS_NR_BITS (PAGE_SHIFT - ilog2(sizeof(atomic_t))) 27 #define BARRIER_BUCKETS_NR (1<<BARRIER_BUCKETS_NR_BITS) 28 29 /* Note: raid1_info.rdev can be set to NULL asynchronously by raid1_remove_disk. 30 * There are three safe ways to access raid1_info.rdev. 31 * 1/ when holding mddev->reconfig_mutex 32 * 2/ when resync/recovery is known to be happening - i.e. in code that is 33 * called as part of performing resync/recovery. 34 * 3/ while holding rcu_read_lock(), use rcu_dereference to get the pointer 35 * and if it is non-NULL, increment rdev->nr_pending before dropping the 36 * RCU lock. 37 * When .rdev is set to NULL, the nr_pending count checked again and if it has 38 * been incremented, the pointer is put back in .rdev. 39 */ 40 41 struct raid1_info { 42 struct md_rdev *rdev; 43 sector_t head_position; 44 45 /* When choose the best device for a read (read_balance()) 46 * we try to keep sequential reads one the same device 47 */ 48 sector_t next_seq_sect; 49 sector_t seq_start; 50 }; 51 52 /* 53 * memory pools need a pointer to the mddev, so they can force an unplug 54 * when memory is tight, and a count of the number of drives that the 55 * pool was allocated for, so they know how much to allocate and free. 56 * mddev->raid_disks cannot be used, as it can change while a pool is active 57 * These two datums are stored in a kmalloced struct. 58 * The 'raid_disks' here is twice the raid_disks in r1conf. 59 * This allows space for each 'real' device can have a replacement in the 60 * second half of the array. 61 */ 62 63 struct pool_info { 64 struct mddev *mddev; 65 int raid_disks; 66 }; 67 68 struct r1conf { 69 struct mddev *mddev; 70 struct raid1_info *mirrors; /* twice 'raid_disks' to 71 * allow for replacements. 72 */ 73 int raid_disks; 74 75 spinlock_t device_lock; 76 77 /* list of 'struct r1bio' that need to be processed by raid1d, 78 * whether to retry a read, writeout a resync or recovery 79 * block, or anything else. 80 */ 81 struct list_head retry_list; 82 /* A separate list of r1bio which just need raid_end_bio_io called. 83 * This mustn't happen for writes which had any errors if the superblock 84 * needs to be written. 85 */ 86 struct list_head bio_end_io_list; 87 88 /* queue pending writes to be submitted on unplug */ 89 struct bio_list pending_bio_list; 90 91 /* for use when syncing mirrors: 92 * We don't allow both normal IO and resync/recovery IO at 93 * the same time - resync/recovery can only happen when there 94 * is no other IO. So when either is active, the other has to wait. 95 * See more details description in raid1.c near raise_barrier(). 96 */ 97 wait_queue_head_t wait_barrier; 98 spinlock_t resync_lock; 99 atomic_t nr_sync_pending; 100 atomic_t *nr_pending; 101 atomic_t *nr_waiting; 102 atomic_t *nr_queued; 103 atomic_t *barrier; 104 int array_frozen; 105 106 /* Set to 1 if a full sync is needed, (fresh device added). 107 * Cleared when a sync completes. 108 */ 109 int fullsync; 110 111 /* When the same as mddev->recovery_disabled we don't allow 112 * recovery to be attempted as we expect a read error. 113 */ 114 int recovery_disabled; 115 116 /* poolinfo contains information about the content of the 117 * mempools - it changes when the array grows or shrinks 118 */ 119 struct pool_info *poolinfo; 120 mempool_t r1bio_pool; 121 mempool_t r1buf_pool; 122 123 struct bio_set bio_split; 124 125 /* temporary buffer to synchronous IO when attempting to repair 126 * a read error. 127 */ 128 struct page *tmppage; 129 130 /* When taking over an array from a different personality, we store 131 * the new thread here until we fully activate the array. 132 */ 133 struct md_thread __rcu *thread; 134 135 /* Keep track of cluster resync window to send to other 136 * nodes. 137 */ 138 sector_t cluster_sync_low; 139 sector_t cluster_sync_high; 140 141 }; 142 143 /* 144 * this is our 'private' RAID1 bio. 145 * 146 * it contains information about what kind of IO operations were started 147 * for this RAID1 operation, and about their status: 148 */ 149 150 struct r1bio { 151 atomic_t remaining; /* 'have we finished' count, 152 * used from IRQ handlers 153 */ 154 atomic_t behind_remaining; /* number of write-behind ios remaining 155 * in this BehindIO request 156 */ 157 sector_t sector; 158 int sectors; 159 unsigned long state; 160 struct mddev *mddev; 161 /* 162 * original bio going to /dev/mdx 163 */ 164 struct bio *master_bio; 165 /* 166 * if the IO is in READ direction, then this is where we read 167 */ 168 int read_disk; 169 170 struct list_head retry_list; 171 172 /* 173 * When R1BIO_BehindIO is set, we store pages for write behind 174 * in behind_master_bio. 175 */ 176 struct bio *behind_master_bio; 177 178 /* 179 * if the IO is in WRITE direction, then multiple bios are used. 180 * We choose the number when they are allocated. 181 */ 182 struct bio *bios[]; 183 /* DO NOT PUT ANY NEW FIELDS HERE - bios array is contiguously alloced*/ 184 }; 185 186 /* bits for r1bio.state */ 187 enum r1bio_state { 188 R1BIO_Uptodate, 189 R1BIO_IsSync, 190 R1BIO_Degraded, 191 R1BIO_BehindIO, 192 /* Set ReadError on bios that experience a readerror so that 193 * raid1d knows what to do with them. 194 */ 195 R1BIO_ReadError, 196 /* For write-behind requests, we call bi_end_io when 197 * the last non-write-behind device completes, providing 198 * any write was successful. Otherwise we call when 199 * any write-behind write succeeds, otherwise we call 200 * with failure when last write completes (and all failed). 201 * Record that bi_end_io was called with this flag... 202 */ 203 R1BIO_Returned, 204 /* If a write for this request means we can clear some 205 * known-bad-block records, we set this flag 206 */ 207 R1BIO_MadeGood, 208 R1BIO_WriteError, 209 R1BIO_FailFast, 210 }; 211 212 static inline int sector_to_idx(sector_t sector) 213 { 214 return hash_long(sector >> BARRIER_UNIT_SECTOR_BITS, 215 BARRIER_BUCKETS_NR_BITS); 216 } 217 #endif 218