1# SPDX-License-Identifier: GPL-2.0-only 2menuconfig LEDS_TRIGGERS 3 bool "LED Trigger support" 4 depends on LEDS_CLASS 5 help 6 This option enables trigger support for the leds class. 7 These triggers allow kernel events to drive the LEDs and can 8 be configured via sysfs. If unsure, say Y. 9 10if LEDS_TRIGGERS 11 12config LEDS_TRIGGER_TIMER 13 tristate "LED Timer Trigger" 14 help 15 This allows LEDs to be controlled by a programmable timer 16 via sysfs. Some LED hardware can be programmed to start 17 blinking the LED without any further software interaction. 18 For more details read Documentation/leds/leds-class.rst. 19 20 If unsure, say Y. 21 22config LEDS_TRIGGER_ONESHOT 23 tristate "LED One-shot Trigger" 24 help 25 This allows LEDs to blink in one-shot pulses with parameters 26 controlled via sysfs. It's useful to notify the user on 27 sporadic events, when there are no clear begin and end trap points, 28 or on dense events, where this blinks the LED at constant rate if 29 rearmed continuously. 30 31 It also shows how to use the led_blink_set_oneshot() function. 32 33 If unsure, say Y. 34 35config LEDS_TRIGGER_DISK 36 bool "LED Disk Trigger" 37 depends on IDE_GD_ATA || ATA 38 help 39 This allows LEDs to be controlled by disk activity. 40 If unsure, say Y. 41 42config LEDS_TRIGGER_MTD 43 bool "LED MTD (NAND/NOR) Trigger" 44 depends on MTD 45 help 46 This allows LEDs to be controlled by MTD activity. 47 If unsure, say N. 48 49config LEDS_TRIGGER_HEARTBEAT 50 tristate "LED Heartbeat Trigger" 51 help 52 This allows LEDs to be controlled by a CPU load average. 53 The flash frequency is a hyperbolic function of the 1-minute 54 load average. 55 If unsure, say Y. 56 57config LEDS_TRIGGER_BACKLIGHT 58 tristate "LED backlight Trigger" 59 help 60 This allows LEDs to be controlled as a backlight device: they 61 turn off and on when the display is blanked and unblanked. 62 63 If unsure, say N. 64 65config LEDS_TRIGGER_CPU 66 bool "LED CPU Trigger" 67 help 68 This allows LEDs to be controlled by active CPUs. This shows 69 the active CPUs across an array of LEDs so you can see which 70 CPUs are active on the system at any given moment. 71 72 If unsure, say N. 73 74config LEDS_TRIGGER_ACTIVITY 75 tristate "LED activity Trigger" 76 help 77 This allows LEDs to be controlled by an immediate CPU usage. 78 The flash frequency and duty cycle varies from faint flashes to 79 intense brightness depending on the instant CPU load. 80 If unsure, say N. 81 82config LEDS_TRIGGER_GPIO 83 tristate "LED GPIO Trigger" 84 depends on GPIOLIB || COMPILE_TEST 85 help 86 This allows LEDs to be controlled by gpio events. It's good 87 when using gpios as switches and triggering the needed LEDs 88 from there. One use case is n810's keypad LEDs that could 89 be triggered by this trigger when user slides up to show 90 keypad. 91 92 If unsure, say N. 93 94config LEDS_TRIGGER_DEFAULT_ON 95 tristate "LED Default ON Trigger" 96 help 97 This allows LEDs to be initialised in the ON state. 98 If unsure, say Y. 99 100comment "iptables trigger is under Netfilter config (LED target)" 101 depends on LEDS_TRIGGERS 102 103config LEDS_TRIGGER_TRANSIENT 104 tristate "LED Transient Trigger" 105 help 106 This allows one time activation of a transient state on 107 GPIO/PWM based hardware. 108 If unsure, say Y. 109 110config LEDS_TRIGGER_CAMERA 111 tristate "LED Camera Flash/Torch Trigger" 112 help 113 This allows LEDs to be controlled as a camera flash/torch device. 114 This enables direct flash/torch on/off by the driver, kernel space. 115 If unsure, say Y. 116 117config LEDS_TRIGGER_PANIC 118 bool "LED Panic Trigger" 119 help 120 This allows LEDs to be configured to blink on a kernel panic. 121 Enabling this option will allow to mark certain LEDs as panic indicators, 122 allowing to blink them on a kernel panic, even if they are set to 123 a different trigger. 124 If unsure, say Y. 125 126config LEDS_TRIGGER_NETDEV 127 tristate "LED Netdev Trigger" 128 depends on NET 129 help 130 This allows LEDs to be controlled by network device activity. 131 If unsure, say Y. 132 133config LEDS_TRIGGER_PATTERN 134 tristate "LED Pattern Trigger" 135 help 136 This allows LEDs to be controlled by a software or hardware pattern 137 which is a series of tuples, of brightness and duration (ms). 138 If unsure, say N 139 140config LEDS_TRIGGER_AUDIO 141 tristate "Audio Mute LED Trigger" 142 help 143 This allows LEDs to be controlled by audio drivers for following 144 the audio mute and mic-mute changes. 145 If unsure, say N 146 147config LEDS_TRIGGER_TTY 148 tristate "LED Trigger for TTY devices" 149 depends on TTY 150 help 151 This allows LEDs to be controlled by activity on ttys which includes 152 serial devices like /dev/ttyS0. 153 154 When build as a module this driver will be called ledtrig-tty. 155 156endif # LEDS_TRIGGERS 157