xref: /openbmc/linux/drivers/leds/Kconfig (revision ee7da21a) 
1# SPDX-License-Identifier: GPL-2.0-only
2config LEDS_GPIO_REGISTER
3	bool
4	help
5	  This option provides the function gpio_led_register_device.
6	  As this function is used by arch code it must not be compiled as a
7	  module.
8
9menuconfig NEW_LEDS
10	bool "LED Support"
11	help
12	  Say Y to enable Linux LED support.  This allows control of supported
13	  LEDs from both userspace and optionally, by kernel events (triggers).
14
15if NEW_LEDS
16
17config LEDS_CLASS
18	tristate "LED Class Support"
19	help
20	  This option enables the LED sysfs class in /sys/class/leds.  You'll
21	  need this to do anything useful with LEDs.  If unsure, say Y.
22
23config LEDS_CLASS_FLASH
24	tristate "LED Flash Class Support"
25	depends on LEDS_CLASS
26	help
27	  This option enables the flash LED sysfs class in /sys/class/leds.
28	  It wraps LED Class and adds flash LEDs specific sysfs attributes
29	  and kernel internal API to it. You'll need this to provide support
30	  for the flash related features of a LED device. It can be built
31	  as a module.
32
33config LEDS_CLASS_MULTICOLOR
34	tristate "LED Multicolor Class Support"
35	depends on LEDS_CLASS
36	help
37	  This option enables the multicolor LED sysfs class in /sys/class/leds.
38	  It wraps LED class and adds multicolor LED specific sysfs attributes
39	  and kernel internal API to it. You'll need this to provide support
40	  for multicolor LEDs that are grouped together. This class is not
41	  intended for single color LEDs. It can be built as a module.
42
43config LEDS_BRIGHTNESS_HW_CHANGED
44	bool "LED Class brightness_hw_changed attribute support"
45	depends on LEDS_CLASS
46	help
47	  This option enables support for the brightness_hw_changed attribute
48	  for LED sysfs class devices under /sys/class/leds.
49
50	  See Documentation/ABI/testing/sysfs-class-led for details.
51
52comment "LED drivers"
53
54config LEDS_88PM860X
55	tristate "LED Support for Marvell 88PM860x PMIC"
56	depends on LEDS_CLASS
57	depends on MFD_88PM860X
58	help
59	  This option enables support for on-chip LED drivers found on Marvell
60	  Semiconductor 88PM8606 PMIC.
61
62config LEDS_AAT1290
63	tristate "LED support for the AAT1290"
64	depends on LEDS_CLASS_FLASH
65	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
66	depends on GPIOLIB || COMPILE_TEST
67	depends on OF
68	depends on PINCTRL
69	help
70	  This option enables support for the LEDs on the AAT1290.
71
72config LEDS_AN30259A
73	tristate "LED support for Panasonic AN30259A"
74	depends on LEDS_CLASS && I2C && OF
75	help
76	  This option enables support for the AN30259A 3-channel
77	  LED driver.
78
79	  To compile this driver as a module, choose M here: the module
80	  will be called leds-an30259a.
81
82config LEDS_APU
83	tristate "Front panel LED support for PC Engines APU/APU2/APU3 boards"
84	depends on LEDS_CLASS
85	depends on X86 && DMI
86	help
87	  This driver makes the PC Engines APU1 front panel LEDs
88	  accessible from userspace programs through the LED subsystem.
89
90	  If you're looking for APU2/3, use the pcengines-apu2 driver.
91	  (symbol CONFIG_PCENGINES_APU2)
92
93	  To compile this driver as a module, choose M here: the
94	  module will be called leds-apu.
95
96config LEDS_ARIEL
97	tristate "Dell Wyse 3020 status LED support"
98	depends on LEDS_CLASS
99	depends on (MACH_MMP3_DT && MFD_ENE_KB3930) || COMPILE_TEST
100	help
101	  This driver adds support for controlling the front panel status
102	  LEDs on Dell Wyse 3020 (Ariel) board via the KB3930 Embedded
103	  Controller.
104
105	  Say Y to if your machine is a Dell Wyse 3020 thin client.
106
107config LEDS_AS3645A
108	tristate "AS3645A and LM3555 LED flash controllers support"
109	depends on I2C && LEDS_CLASS_FLASH
110	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
111	help
112	  Enable LED flash class support for AS3645A LED flash
113	  controller. V4L2 flash API is provided as well if
114	  CONFIG_V4L2_FLASH_API is enabled.
115
116config LEDS_AW2013
117	tristate "LED support for Awinic AW2013"
118	depends on LEDS_CLASS && I2C && OF
119	help
120	  This option enables support for the AW2013 3-channel
121	  LED driver.
122
123	  To compile this driver as a module, choose M here: the module
124	  will be called leds-aw2013.
125
126config LEDS_BCM6328
127	tristate "LED Support for Broadcom BCM6328"
128	depends on LEDS_CLASS
129	depends on HAS_IOMEM
130	depends on OF
131	help
132	  This option enables support for LEDs connected to the BCM6328
133	  LED HW controller accessed via MMIO registers.
134
135config LEDS_BCM6358
136	tristate "LED Support for Broadcom BCM6358"
137	depends on LEDS_CLASS
138	depends on HAS_IOMEM
139	depends on OF
140	help
141	  This option enables support for LEDs connected to the BCM6358
142	  LED HW controller accessed via MMIO registers.
143
144config LEDS_CPCAP
145	tristate "LED Support for Motorola CPCAP"
146	depends on LEDS_CLASS
147	depends on MFD_CPCAP
148	depends on OF
149	help
150	  This option enables support for LEDs offered by Motorola's
151	  CPCAP PMIC.
152
153config LEDS_CR0014114
154	tristate "LED Support for Crane CR0014114"
155	depends on LEDS_CLASS
156	depends on SPI
157	depends on OF
158	help
159	  This option enables support for CR0014114 LED Board which
160	  is widely used in vending machines produced by
161	  Crane Merchandising Systems.
162
163	  To compile this driver as a module, choose M here: the module
164	  will be called leds-cr0014114.
165
166config LEDS_EL15203000
167	tristate "LED Support for Crane EL15203000"
168	depends on LEDS_CLASS
169	depends on SPI
170	depends on OF
171	help
172	  This option enables support for EL15203000 LED Board
173	  (aka RED LED board) which is widely used in coffee vending
174	  machines produced by Crane Merchandising Systems.
175
176	  To compile this driver as a module, choose M here: the module
177	  will be called leds-el15203000.
178
179config LEDS_TURRIS_OMNIA
180	tristate "LED support for CZ.NIC's Turris Omnia"
181	depends on LEDS_CLASS_MULTICOLOR
182	depends on I2C
183	depends on MACH_ARMADA_38X || COMPILE_TEST
184	depends on OF
185	help
186	  This option enables basic support for the LEDs found on the front
187	  side of CZ.NIC's Turris Omnia router. There are 12 RGB LEDs on the
188	  front panel.
189
190config LEDS_LM3530
191	tristate "LCD Backlight driver for LM3530"
192	depends on LEDS_CLASS
193	depends on I2C
194	help
195	  This option enables support for the LCD backlight using
196	  LM3530 ambient light sensor chip. This ALS chip can be
197	  controlled manually or using PWM input or using ambient
198	  light automatically.
199
200config LEDS_LM3532
201	tristate "LCD Backlight driver for LM3532"
202	select REGMAP_I2C
203	depends on LEDS_CLASS
204	depends on I2C
205	help
206	  This option enables support for the LCD backlight using
207	  LM3532 ambient light sensor chip. This ALS chip can be
208	  controlled manually or using PWM input or using ambient
209	  light automatically.
210
211config LEDS_LM3533
212	tristate "LED support for LM3533"
213	depends on LEDS_CLASS
214	depends on MFD_LM3533
215	help
216	  This option enables support for the LEDs on National Semiconductor /
217	  TI LM3533 Lighting Power chips.
218
219	  The LEDs can be controlled directly, through PWM input, or by the
220	  ambient-light-sensor interface. The chip supports
221	  hardware-accelerated blinking with maximum on and off periods of 9.8
222	  and 77 seconds respectively.
223
224config LEDS_LM3642
225	tristate "LED support for LM3642 Chip"
226	depends on LEDS_CLASS && I2C
227	select REGMAP_I2C
228	help
229	  This option enables support for LEDs connected to LM3642.
230	  The LM3642 is a 4MHz fixed-frequency synchronous boost
231	  converter plus 1.5A constant current driver for a high-current
232	  white LED.
233
234config LEDS_LM3692X
235	tristate "LED support for LM3692x Chips"
236	depends on LEDS_CLASS && I2C && OF
237	select REGMAP_I2C
238	help
239	  This option enables support for the TI LM3692x family
240	  of white LED string drivers used for backlighting.
241
242config LEDS_LM3601X
243	tristate "LED support for LM3601x Chips"
244	depends on LEDS_CLASS && I2C
245	depends on LEDS_CLASS_FLASH
246	select REGMAP_I2C
247	help
248	  This option enables support for the TI LM3601x family
249	  of flash, torch and indicator classes.
250
251config LEDS_LOCOMO
252	tristate "LED Support for Locomo device"
253	depends on LEDS_CLASS
254	depends on SHARP_LOCOMO
255	help
256	  This option enables support for the LEDs on Sharp Locomo.
257	  Zaurus models SL-5500 and SL-5600.
258
259config LEDS_MIKROTIK_RB532
260	tristate "LED Support for Mikrotik Routerboard 532"
261	depends on LEDS_CLASS
262	depends on MIKROTIK_RB532
263	help
264	  This option enables support for the so called "User LED" of
265	  Mikrotik's Routerboard 532.
266
267config LEDS_MT6323
268	tristate "LED Support for Mediatek MT6323 PMIC"
269	depends on LEDS_CLASS
270	depends on MFD_MT6397
271	help
272	  This option enables support for on-chip LED drivers found on
273	  Mediatek MT6323 PMIC.
274
275config LEDS_S3C24XX
276	tristate "LED Support for Samsung S3C24XX GPIO LEDs"
277	depends on LEDS_CLASS
278	depends on ARCH_S3C24XX || COMPILE_TEST
279	help
280	  This option enables support for LEDs connected to GPIO lines
281	  on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.
282
283config LEDS_NET48XX
284	tristate "LED Support for Soekris net48xx series Error LED"
285	depends on LEDS_CLASS
286	depends on SCx200_GPIO
287	help
288	  This option enables support for the Soekris net4801 and net4826 error
289	  LED.
290
291config LEDS_FSG
292	tristate "LED Support for the Freecom FSG-3"
293	depends on LEDS_CLASS
294	depends on MACH_FSG
295	help
296	  This option enables support for the LEDs on the Freecom FSG-3.
297
298config LEDS_WRAP
299	tristate "LED Support for the WRAP series LEDs"
300	depends on LEDS_CLASS
301	depends on SCx200_GPIO
302	help
303	  This option enables support for the PCEngines WRAP programmable LEDs.
304
305config LEDS_COBALT_QUBE
306	tristate "LED Support for the Cobalt Qube series front LED"
307	depends on LEDS_CLASS
308	depends on MIPS_COBALT || COMPILE_TEST
309	help
310	  This option enables support for the front LED on Cobalt Qube series
311
312config LEDS_COBALT_RAQ
313	bool "LED Support for the Cobalt Raq series"
314	depends on LEDS_CLASS=y && (MIPS_COBALT || COMPILE_TEST)
315	select LEDS_TRIGGERS
316	help
317	  This option enables support for the Cobalt Raq series LEDs.
318
319config LEDS_SUNFIRE
320	tristate "LED support for SunFire servers."
321	depends on LEDS_CLASS
322	depends on SPARC64
323	select LEDS_TRIGGERS
324	help
325	  This option enables support for the Left, Middle, and Right
326	  LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.
327
328config LEDS_IPAQ_MICRO
329	tristate "LED Support for the Compaq iPAQ h3xxx"
330	depends on LEDS_CLASS
331	depends on MFD_IPAQ_MICRO
332	help
333	  Choose this option if you want to use the notification LED on
334	  Compaq/HP iPAQ h3100 and h3600.
335
336config LEDS_HP6XX
337	tristate "LED Support for the HP Jornada 6xx"
338	depends on LEDS_CLASS
339	depends on SH_HP6XX
340	help
341	  This option enables LED support for the handheld
342	  HP Jornada 620/660/680/690.
343
344config LEDS_PCA9532
345	tristate "LED driver for PCA9532 dimmer"
346	depends on LEDS_CLASS
347	depends on I2C && INPUT
348	help
349	  This option enables support for NXP pca9532
350	  LED controller. It is generally only useful
351	  as a platform driver
352
353config LEDS_PCA9532_GPIO
354	bool "Enable GPIO support for PCA9532"
355	depends on LEDS_PCA9532
356	depends on GPIOLIB
357	help
358	  Allow unused pins on PCA9532 to be used as gpio.
359
360	  To use a pin as gpio pca9532_type in pca9532_platform data needs to
361	  set to PCA9532_TYPE_GPIO.
362
363config LEDS_GPIO
364	tristate "LED Support for GPIO connected LEDs"
365	depends on LEDS_CLASS
366	depends on GPIOLIB || COMPILE_TEST
367	help
368	  This option enables support for the LEDs connected to GPIO
369	  outputs. To be useful the particular board must have LEDs
370	  and they must be connected to the GPIO lines.  The LEDs must be
371	  defined as platform devices and/or OpenFirmware platform devices.
372	  The code to use these bindings can be selected below.
373
374config LEDS_LP3944
375	tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
376	depends on LEDS_CLASS
377	depends on I2C
378	help
379	  This option enables support for LEDs connected to the National
380	  Semiconductor LP3944 Lighting Management Unit (LMU) also known as
381	  Fun Light Chip.
382
383	  To compile this driver as a module, choose M here: the
384	  module will be called leds-lp3944.
385
386config LEDS_LP3952
387	tristate "LED Support for TI LP3952 2 channel LED driver"
388	depends on LEDS_CLASS
389	depends on I2C
390	depends on GPIOLIB
391	select REGMAP_I2C
392	help
393	  This option enables support for LEDs connected to the Texas
394	  Instruments LP3952 LED driver.
395
396	  To compile this driver as a module, choose M here: the
397	  module will be called leds-lp3952.
398
399config LEDS_LP50XX
400	tristate "LED Support for TI LP5036/30/24/18/12/9 LED driver chip"
401	depends on LEDS_CLASS && REGMAP_I2C
402	depends on LEDS_CLASS_MULTICOLOR || !LEDS_CLASS_MULTICOLOR
403	help
404	  If you say yes here you get support for the Texas Instruments
405	  LP5036, LP5030, LP5024, LP5018, LP5012 and LP5009 LED driver.
406
407	  To compile this driver as a module, choose M here: the
408	  module will be called leds-lp50xx.
409
410config LEDS_LP55XX_COMMON
411	tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
412	depends on LEDS_CLASS
413	depends on LEDS_CLASS_MULTICOLOR || !LEDS_CLASS_MULTICOLOR
414	depends on OF
415	depends on I2C
416	select FW_LOADER
417	select FW_LOADER_USER_HELPER
418	help
419	  This option supports common operations for LP5521/5523/55231/5562/8501
420	  devices.
421
422config LEDS_LP5521
423	tristate "LED Support for N.S. LP5521 LED driver chip"
424	depends on LEDS_CLASS && I2C
425	depends on LEDS_LP55XX_COMMON
426	help
427	  If you say yes here you get support for the National Semiconductor
428	  LP5521 LED driver. It is 3 channel chip with programmable engines.
429	  Driver provides direct control via LED class and interface for
430	  programming the engines.
431
432config LEDS_LP5523
433	tristate "LED Support for TI/National LP5523/55231 LED driver chip"
434	depends on LEDS_CLASS && I2C
435	depends on LEDS_LP55XX_COMMON
436	help
437	  If you say yes here you get support for TI/National Semiconductor
438	  LP5523/55231 LED driver.
439	  It is 9 channel chip with programmable engines.
440	  Driver provides direct control via LED class and interface for
441	  programming the engines.
442
443config LEDS_LP5562
444	tristate "LED Support for TI LP5562 LED driver chip"
445	depends on LEDS_CLASS && I2C
446	depends on LEDS_LP55XX_COMMON
447	help
448	  If you say yes here you get support for TI LP5562 LED driver.
449	  It is 4 channels chip with programmable engines.
450	  Driver provides direct control via LED class and interface for
451	  programming the engines.
452
453config LEDS_LP8501
454	tristate "LED Support for TI LP8501 LED driver chip"
455	depends on LEDS_CLASS && I2C
456	depends on LEDS_LP55XX_COMMON
457	help
458	  If you say yes here you get support for TI LP8501 LED driver.
459	  It is 9 channel chip with programmable engines.
460	  Driver provides direct control via LED class and interface for
461	  programming the engines.
462	  It is similar as LP5523, but output power selection is available.
463	  And register layout and engine program schemes are different.
464
465config LEDS_LP8788
466	tristate "LED support for the TI LP8788 PMIC"
467	depends on LEDS_CLASS
468	depends on MFD_LP8788
469	help
470	  This option enables support for the Keyboard LEDs on the LP8788 PMIC.
471
472config LEDS_LP8860
473	tristate "LED support for the TI LP8860 4 channel LED driver"
474	depends on LEDS_CLASS && I2C && OF
475	select REGMAP_I2C
476	help
477	  If you say yes here you get support for the TI LP8860 4 channel
478	  LED driver.
479	  This option enables support for the display cluster LEDs
480	  on the LP8860 4 channel LED driver using the I2C communication
481	  bus.
482
483config LEDS_CLEVO_MAIL
484	tristate "Mail LED on Clevo notebook"
485	depends on LEDS_CLASS
486	depends on X86 && SERIO_I8042 && DMI
487	help
488	  This driver makes the mail LED accessible from userspace
489	  programs through the leds subsystem. This LED have three
490	  known mode: off, blink at 0.5Hz and blink at 1Hz.
491
492	  The driver supports two kinds of interface: using ledtrig-timer
493	  or through /sys/class/leds/clevo::mail/brightness. As this LED
494	  cannot change it's brightness it blinks instead. The brightness
495	  value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
496	  blink at 1Hz.
497
498	  This module can drive the mail LED for the following notebooks:
499
500	        Clevo D400P
501	        Clevo D410J
502	        Clevo D410V
503	        Clevo D400V/D470V (not tested, but might work)
504	        Clevo M540N
505	        Clevo M5x0N (not tested, but might work)
506	        Positivo Mobile (Clevo M5x0V)
507
508	  If your model is not listed here you can try the "nodetect"
509	  module parameter.
510
511	  To compile this driver as a module, choose M here: the
512	  module will be called leds-clevo-mail.
513
514config LEDS_PCA955X
515	tristate "LED Support for PCA955x I2C chips"
516	depends on LEDS_CLASS
517	depends on I2C
518	help
519	  This option enables support for LEDs connected to PCA955x
520	  LED driver chips accessed via the I2C bus.  Supported
521	  devices include PCA9550, PCA9551, PCA9552, and PCA9553.
522
523config LEDS_PCA955X_GPIO
524	bool "Enable GPIO support for PCA955X"
525	depends on LEDS_PCA955X
526	depends on GPIOLIB
527	help
528	  Allow unused pins on PCA955X to be used as gpio.
529
530	  To use a pin as gpio the pin type should be set to
531	  PCA955X_TYPE_GPIO in the device tree.
532
533
534config LEDS_PCA963X
535	tristate "LED support for PCA963x I2C chip"
536	depends on LEDS_CLASS
537	depends on I2C
538	help
539	  This option enables support for LEDs connected to the PCA963x
540	  LED driver chip accessed via the I2C bus. Supported
541	  devices include PCA9633 and PCA9634
542
543config LEDS_WM831X_STATUS
544	tristate "LED support for status LEDs on WM831x PMICs"
545	depends on LEDS_CLASS
546	depends on MFD_WM831X
547	help
548	  This option enables support for the status LEDs of the WM831x
549	  series of PMICs.
550
551config LEDS_WM8350
552	tristate "LED Support for WM8350 AudioPlus PMIC"
553	depends on LEDS_CLASS
554	depends on MFD_WM8350
555	help
556	  This option enables support for LEDs driven by the Wolfson
557	  Microelectronics WM8350 AudioPlus PMIC.
558
559config LEDS_DA903X
560	tristate "LED Support for DA9030/DA9034 PMIC"
561	depends on LEDS_CLASS
562	depends on PMIC_DA903X
563	help
564	  This option enables support for on-chip LED drivers found
565	  on Dialog Semiconductor DA9030/DA9034 PMICs.
566
567config LEDS_DA9052
568	tristate "Dialog DA9052/DA9053 LEDS"
569	depends on LEDS_CLASS
570	depends on PMIC_DA9052
571	help
572	  This option enables support for on-chip LED drivers found
573	  on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
574
575config LEDS_DAC124S085
576	tristate "LED Support for DAC124S085 SPI DAC"
577	depends on LEDS_CLASS
578	depends on SPI
579	help
580	  This option enables support for DAC124S085 SPI DAC from NatSemi,
581	  which can be used to control up to four LEDs.
582
583config LEDS_PWM
584	tristate "PWM driven LED Support"
585	depends on LEDS_CLASS
586	depends on PWM
587	help
588	  This option enables support for pwm driven LEDs
589
590config LEDS_REGULATOR
591	tristate "REGULATOR driven LED support"
592	depends on LEDS_CLASS
593	depends on REGULATOR
594	help
595	  This option enables support for regulator driven LEDs.
596
597config LEDS_BD2802
598	tristate "LED driver for BD2802 RGB LED"
599	depends on LEDS_CLASS
600	depends on I2C
601	help
602	  This option enables support for BD2802GU RGB LED driver chips
603	  accessed via the I2C bus.
604
605config LEDS_INTEL_SS4200
606	tristate "LED driver for Intel NAS SS4200 series"
607	depends on LEDS_CLASS
608	depends on PCI && DMI
609	depends on X86
610	help
611	  This option enables support for the Intel SS4200 series of
612	  Network Attached Storage servers. You may control the hard
613	  drive or power LEDs on the front panel. Using this driver
614	  can stop the front LED from blinking after startup.
615
616config LEDS_LT3593
617	tristate "LED driver for LT3593 controllers"
618	depends on LEDS_CLASS
619	depends on GPIOLIB || COMPILE_TEST
620	help
621	  This option enables support for LEDs driven by a Linear Technology
622	  LT3593 controller. This controller uses a special one-wire pulse
623	  coding protocol to set the brightness.
624
625config LEDS_ADP5520
626	tristate "LED Support for ADP5520/ADP5501 PMIC"
627	depends on LEDS_CLASS
628	depends on PMIC_ADP5520
629	help
630	  This option enables support for on-chip LED drivers found
631	  on Analog Devices ADP5520/ADP5501 PMICs.
632
633	  To compile this driver as a module, choose M here: the module will
634	  be called leds-adp5520.
635
636config LEDS_MC13783
637	tristate "LED Support for MC13XXX PMIC"
638	depends on LEDS_CLASS
639	depends on MFD_MC13XXX
640	help
641	  This option enables support for on-chip LED drivers found
642	  on Freescale Semiconductor MC13783/MC13892/MC34708 PMIC.
643
644config LEDS_NS2
645	tristate "LED support for Network Space v2 GPIO LEDs"
646	depends on LEDS_CLASS
647	depends on MACH_KIRKWOOD || MACH_ARMADA_370 || COMPILE_TEST
648	default y
649	help
650	  This option enables support for the dual-GPIO LEDs found on the
651	  following LaCie/Seagate boards:
652
653		Network Space v2 (and parents: Max, Mini)
654		Internet Space v2
655		d2 Network v2
656		n090401 (Seagate NAS 4-Bay)
657
658config LEDS_NETXBIG
659	tristate "LED support for Big Network series LEDs"
660	depends on LEDS_CLASS
661	depends on MACH_KIRKWOOD || COMPILE_TEST
662	depends on OF_GPIO
663	default y
664	help
665	  This option enables support for LEDs found on the LaCie 2Big
666	  and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
667	  controlled through a GPIO extension bus.
668
669config LEDS_ASIC3
670	bool "LED support for the HTC ASIC3"
671	depends on LEDS_CLASS=y
672	depends on MFD_ASIC3
673	default y
674	help
675	  This option enables support for the LEDs on the HTC ASIC3. The HTC
676	  ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
677	  cannot be used. This driver supports hardware blinking with an on+off
678	  period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.
679
680config LEDS_TCA6507
681	tristate "LED Support for TCA6507 I2C chip"
682	depends on LEDS_CLASS && I2C
683	help
684	  This option enables support for LEDs connected to TC6507
685	  LED driver chips accessed via the I2C bus.
686	  Driver support brightness control and hardware-assisted blinking.
687
688config LEDS_TLC591XX
689	tristate "LED driver for TLC59108 and TLC59116 controllers"
690	depends on LEDS_CLASS && I2C
691	select REGMAP_I2C
692	help
693	  This option enables support for Texas Instruments TLC59108
694	  and TLC59116 LED controllers.
695
696config LEDS_MAX77650
697	tristate "LED support for Maxim MAX77650 PMIC"
698	depends on LEDS_CLASS && MFD_MAX77650
699	help
700	  LEDs driver for MAX77650 family of PMICs from Maxim Integrated.
701
702config LEDS_MAX77693
703	tristate "LED support for MAX77693 Flash"
704	depends on LEDS_CLASS_FLASH
705	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
706	depends on MFD_MAX77693
707	depends on OF
708	help
709	  This option enables support for the flash part of the MAX77693
710	  multifunction device. It has build in control for two leds in flash
711	  and torch mode.
712
713config LEDS_MAX8997
714	tristate "LED support for MAX8997 PMIC"
715	depends on LEDS_CLASS && MFD_MAX8997
716	help
717	  This option enables support for on-chip LED drivers on
718	  MAXIM MAX8997 PMIC.
719
720config LEDS_LM355x
721	tristate "LED support for LM3554 and LM3556 chips"
722	depends on LEDS_CLASS && I2C
723	select REGMAP_I2C
724	help
725	  This option enables support for LEDs connected to LM3554
726	  and LM3556. It includes Torch, Flash and Indicator functions.
727
728config LEDS_OT200
729	tristate "LED support for the Bachmann OT200"
730	depends on LEDS_CLASS && HAS_IOMEM && (X86_32 || COMPILE_TEST)
731	help
732	  This option enables support for the LEDs on the Bachmann OT200.
733	  Say Y to enable LEDs on the Bachmann OT200.
734
735config LEDS_MENF21BMC
736	tristate "LED support for the MEN 14F021P00 BMC"
737	depends on LEDS_CLASS && MFD_MENF21BMC
738	help
739	  Say Y here to include support for the MEN 14F021P00 BMC LEDs.
740
741	  This driver can also be built as a module. If so the module
742	  will be called leds-menf21bmc.
743
744config LEDS_KTD2692
745	tristate "LED support for KTD2692 flash LED controller"
746	depends on LEDS_CLASS_FLASH && OF
747	depends on GPIOLIB || COMPILE_TEST
748	help
749	  This option enables support for KTD2692 LED flash connected
750	  through ExpressWire interface.
751
752	  Say Y to enable this driver.
753
754config LEDS_IS31FL319X
755	tristate "LED Support for ISSI IS31FL319x I2C LED controller family"
756	depends on LEDS_CLASS && I2C && OF
757	select REGMAP_I2C
758	help
759	  This option enables support for LEDs connected to ISSI IS31FL319x
760	  fancy LED driver chips accessed via the I2C bus.
761	  Driver supports individual PWM brightness control for each channel.
762
763	  This driver can also be built as a module. If so the module will be
764	  called leds-is31fl319x.
765
766config LEDS_IS31FL32XX
767	tristate "LED support for ISSI IS31FL32XX I2C LED controller family"
768	depends on LEDS_CLASS && I2C && OF
769	help
770	  Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
771	  LED controllers. They are I2C devices with multiple constant-current
772	  channels, each with independent 256-level PWM control.
773
774config LEDS_SC27XX_BLTC
775	tristate "LED support for the SC27xx breathing light controller"
776	depends on LEDS_CLASS && MFD_SC27XX_PMIC
777	depends on OF
778	help
779	  Say Y here to include support for the SC27xx breathing light controller
780	  LEDs.
781
782	  This driver can also be built as a module. If so the module will be
783	  called leds-sc27xx-bltc.
784
785comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)"
786
787config LEDS_BLINKM
788	tristate "LED support for the BlinkM I2C RGB LED"
789	depends on LEDS_CLASS
790	depends on I2C
791	help
792	  This option enables support for the BlinkM RGB LED connected
793	  through I2C. Say Y to enable support for the BlinkM LED.
794
795config LEDS_POWERNV
796	tristate "LED support for PowerNV Platform"
797	depends on LEDS_CLASS
798	depends on PPC_POWERNV
799	depends on OF
800	help
801	  This option enables support for the system LEDs present on
802	  PowerNV platforms. Say 'y' to enable this support in kernel.
803	  To compile this driver as a module, choose 'm' here: the module
804	  will be called leds-powernv.
805
806config LEDS_SYSCON
807	bool "LED support for LEDs on system controllers"
808	depends on LEDS_CLASS=y
809	depends on MFD_SYSCON
810	depends on OF
811	help
812	  This option enables support for the LEDs on syscon type
813	  devices. This will only work with device tree enabled
814	  devices.
815
816config LEDS_PM8058
817	tristate "LED Support for the Qualcomm PM8058 PMIC"
818	depends on MFD_PM8XXX
819	depends on LEDS_CLASS
820	help
821	  Choose this option if you want to use the LED drivers in
822	  the Qualcomm PM8058 PMIC.
823
824config LEDS_MLXCPLD
825	tristate "LED support for the Mellanox boards"
826	depends on X86 && DMI
827	depends on LEDS_CLASS
828	help
829	  This option enables support for the LEDs on the Mellanox
830	  boards. Say Y to enable these.
831
832config LEDS_MLXREG
833	tristate "LED support for the Mellanox switches management control"
834	depends on LEDS_CLASS
835	help
836	  This option enables support for the LEDs on the Mellanox Ethernet and
837	  InfiniBand switches. The driver can be activated by the platform device
838	  device add call. Say Y to enable these. To compile this driver as a
839	  module, choose 'M' here: the module will be called leds-mlxreg.
840
841config LEDS_USER
842	tristate "Userspace LED support"
843	depends on LEDS_CLASS
844	help
845	  This option enables support for userspace LEDs. Say 'y' to enable this
846	  support in kernel. To compile this driver as a module, choose 'm' here:
847	  the module will be called uleds.
848
849config LEDS_NIC78BX
850	tristate "LED support for NI PXI NIC78bx devices"
851	depends on LEDS_CLASS
852	depends on X86 && ACPI
853	help
854	  This option enables support for the User1 and User2 LEDs on NI
855	  PXI NIC78bx devices.
856
857	  To compile this driver as a module, choose M here: the module
858	  will be called leds-nic78bx.
859
860config LEDS_SPI_BYTE
861	tristate "LED support for SPI LED controller with a single byte"
862	depends on LEDS_CLASS
863	depends on SPI
864	depends on OF
865	help
866	  This option enables support for LED controller which use a single byte
867	  for controlling the brightness. Currently the following controller is
868	  supported: Ubiquiti airCube ISP microcontroller based LED controller.
869
870config LEDS_TI_LMU_COMMON
871	tristate "LED driver for TI LMU"
872	depends on LEDS_CLASS
873	depends on REGMAP
874	help
875	  Say Y to enable the LED driver for TI LMU devices.
876	  This supports common features between the TI LM3532, LM3631, LM3632,
877	  LM3633, LM3695 and LM3697.
878
879config LEDS_LM3697
880	tristate "LED driver for LM3697"
881	depends on LEDS_TI_LMU_COMMON
882	depends on I2C && OF
883	help
884	  Say Y to enable the LM3697 LED driver for TI LMU devices.
885	  This supports the LED device LM3697.
886
887config LEDS_LM36274
888	tristate "LED driver for LM36274"
889	depends on LEDS_TI_LMU_COMMON
890	depends on MFD_TI_LMU
891	help
892	  Say Y to enable the LM36274 LED driver for TI LMU devices.
893	  This supports the LED device LM36274.
894
895config LEDS_TPS6105X
896	tristate "LED support for TI TPS6105X"
897	depends on LEDS_CLASS
898	depends on TPS6105X
899	default y if TPS6105X
900	help
901	  This driver supports TPS61050/TPS61052 LED chips.
902	  It is a single boost converter primarily for white LEDs and
903	  audio amplifiers.
904
905config LEDS_IP30
906	tristate "LED support for SGI Octane machines"
907	depends on LEDS_CLASS
908	depends on SGI_MFD_IOC3 || COMPILE_TEST
909	help
910	  This option enables support for the Red and White LEDs of
911	  SGI Octane machines.
912
913	  To compile this driver as a module, choose M here: the module
914	  will be called leds-ip30.
915
916config LEDS_SGM3140
917	tristate "LED support for the SGM3140"
918	depends on LEDS_CLASS_FLASH
919	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
920	help
921	  This option enables support for the SGM3140 500mA Buck/Boost Charge
922	  Pump LED Driver.
923
924config LEDS_ACER_A500
925	tristate "Power button LED support for Acer Iconia Tab A500"
926	depends on LEDS_CLASS && MFD_ACER_A500_EC
927	help
928	  This option enables support for the Power Button LED of
929	  Acer Iconia Tab A500.
930
931source "drivers/leds/blink/Kconfig"
932
933comment "Flash and Torch LED drivers"
934source "drivers/leds/flash/Kconfig"
935
936comment "LED Triggers"
937source "drivers/leds/trigger/Kconfig"
938
939endif # NEW_LEDS
940