1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * hfcmulti.c low level driver for hfc-4s/hfc-8s/hfc-e1 based cards 4 * 5 * Author Andreas Eversberg (jolly@eversberg.eu) 6 * ported to mqueue mechanism: 7 * Peter Sprenger (sprengermoving-bytes.de) 8 * 9 * inspired by existing hfc-pci driver: 10 * Copyright 1999 by Werner Cornelius (werner@isdn-development.de) 11 * Copyright 2008 by Karsten Keil (kkeil@suse.de) 12 * Copyright 2008 by Andreas Eversberg (jolly@eversberg.eu) 13 * 14 * Thanks to Cologne Chip AG for this great controller! 15 */ 16 17 /* 18 * module parameters: 19 * type: 20 * By default (0), the card is automatically detected. 21 * Or use the following combinations: 22 * Bit 0-7 = 0x00001 = HFC-E1 (1 port) 23 * or Bit 0-7 = 0x00004 = HFC-4S (4 ports) 24 * or Bit 0-7 = 0x00008 = HFC-8S (8 ports) 25 * Bit 8 = 0x00100 = uLaw (instead of aLaw) 26 * Bit 9 = 0x00200 = Disable DTMF detect on all B-channels via hardware 27 * Bit 10 = spare 28 * Bit 11 = 0x00800 = Force PCM bus into slave mode. (otherwhise auto) 29 * or Bit 12 = 0x01000 = Force PCM bus into master mode. (otherwhise auto) 30 * Bit 13 = spare 31 * Bit 14 = 0x04000 = Use external ram (128K) 32 * Bit 15 = 0x08000 = Use external ram (512K) 33 * Bit 16 = 0x10000 = Use 64 timeslots instead of 32 34 * or Bit 17 = 0x20000 = Use 128 timeslots instead of anything else 35 * Bit 18 = spare 36 * Bit 19 = 0x80000 = Send the Watchdog a Signal (Dual E1 with Watchdog) 37 * (all other bits are reserved and shall be 0) 38 * example: 0x20204 one HFC-4S with dtmf detection and 128 timeslots on PCM 39 * bus (PCM master) 40 * 41 * port: (optional or required for all ports on all installed cards) 42 * HFC-4S/HFC-8S only bits: 43 * Bit 0 = 0x001 = Use master clock for this S/T interface 44 * (ony once per chip). 45 * Bit 1 = 0x002 = transmitter line setup (non capacitive mode) 46 * Don't use this unless you know what you are doing! 47 * Bit 2 = 0x004 = Disable E-channel. (No E-channel processing) 48 * example: 0x0001,0x0000,0x0000,0x0000 one HFC-4S with master clock 49 * received from port 1 50 * 51 * HFC-E1 only bits: 52 * Bit 0 = 0x0001 = interface: 0=copper, 1=optical 53 * Bit 1 = 0x0002 = reserved (later for 32 B-channels transparent mode) 54 * Bit 2 = 0x0004 = Report LOS 55 * Bit 3 = 0x0008 = Report AIS 56 * Bit 4 = 0x0010 = Report SLIP 57 * Bit 5 = 0x0020 = Report RDI 58 * Bit 8 = 0x0100 = Turn off CRC-4 Multiframe Mode, use double frame 59 * mode instead. 60 * Bit 9 = 0x0200 = Force get clock from interface, even in NT mode. 61 * or Bit 10 = 0x0400 = Force put clock to interface, even in TE mode. 62 * Bit 11 = 0x0800 = Use direct RX clock for PCM sync rather than PLL. 63 * (E1 only) 64 * Bit 12-13 = 0xX000 = elastic jitter buffer (1-3), Set both bits to 0 65 * for default. 66 * (all other bits are reserved and shall be 0) 67 * 68 * debug: 69 * NOTE: only one debug value must be given for all cards 70 * enable debugging (see hfc_multi.h for debug options) 71 * 72 * poll: 73 * NOTE: only one poll value must be given for all cards 74 * Give the number of samples for each fifo process. 75 * By default 128 is used. Decrease to reduce delay, increase to 76 * reduce cpu load. If unsure, don't mess with it! 77 * Valid is 8, 16, 32, 64, 128, 256. 78 * 79 * pcm: 80 * NOTE: only one pcm value must be given for every card. 81 * The PCM bus id tells the mISDNdsp module about the connected PCM bus. 82 * By default (0), the PCM bus id is 100 for the card that is PCM master. 83 * If multiple cards are PCM master (because they are not interconnected), 84 * each card with PCM master will have increasing PCM id. 85 * All PCM busses with the same ID are expected to be connected and have 86 * common time slots slots. 87 * Only one chip of the PCM bus must be master, the others slave. 88 * -1 means no support of PCM bus not even. 89 * Omit this value, if all cards are interconnected or none is connected. 90 * If unsure, don't give this parameter. 91 * 92 * dmask and bmask: 93 * NOTE: One dmask value must be given for every HFC-E1 card. 94 * If omitted, the E1 card has D-channel on time slot 16, which is default. 95 * dmask is a 32 bit mask. The bit must be set for an alternate time slot. 96 * If multiple bits are set, multiple virtual card fragments are created. 97 * For each bit set, a bmask value must be given. Each bit on the bmask 98 * value stands for a B-channel. The bmask may not overlap with dmask or 99 * with other bmask values for that card. 100 * Example: dmask=0x00020002 bmask=0x0000fffc,0xfffc0000 101 * This will create one fragment with D-channel on slot 1 with 102 * B-channels on slots 2..15, and a second fragment with D-channel 103 * on slot 17 with B-channels on slot 18..31. Slot 16 is unused. 104 * If bit 0 is set (dmask=0x00000001) the D-channel is on slot 0 and will 105 * not function. 106 * Example: dmask=0x00000001 bmask=0xfffffffe 107 * This will create a port with all 31 usable timeslots as 108 * B-channels. 109 * If no bits are set on bmask, no B-channel is created for that fragment. 110 * Example: dmask=0xfffffffe bmask=0,0,0,0.... (31 0-values for bmask) 111 * This will create 31 ports with one D-channel only. 112 * If you don't know how to use it, you don't need it! 113 * 114 * iomode: 115 * NOTE: only one mode value must be given for every card. 116 * -> See hfc_multi.h for HFC_IO_MODE_* values 117 * By default, the IO mode is pci memory IO (MEMIO). 118 * Some cards require specific IO mode, so it cannot be changed. 119 * It may be useful to set IO mode to register io (REGIO) to solve 120 * PCI bridge problems. 121 * If unsure, don't give this parameter. 122 * 123 * clockdelay_nt: 124 * NOTE: only one clockdelay_nt value must be given once for all cards. 125 * Give the value of the clock control register (A_ST_CLK_DLY) 126 * of the S/T interfaces in NT mode. 127 * This register is needed for the TBR3 certification, so don't change it. 128 * 129 * clockdelay_te: 130 * NOTE: only one clockdelay_te value must be given once 131 * Give the value of the clock control register (A_ST_CLK_DLY) 132 * of the S/T interfaces in TE mode. 133 * This register is needed for the TBR3 certification, so don't change it. 134 * 135 * clock: 136 * NOTE: only one clock value must be given once 137 * Selects interface with clock source for mISDN and applications. 138 * Set to card number starting with 1. Set to -1 to disable. 139 * By default, the first card is used as clock source. 140 * 141 * hwid: 142 * NOTE: only one hwid value must be given once 143 * Enable special embedded devices with XHFC controllers. 144 */ 145 146 /* 147 * debug register access (never use this, it will flood your system log) 148 * #define HFC_REGISTER_DEBUG 149 */ 150 151 #define HFC_MULTI_VERSION "2.03" 152 153 #include <linux/interrupt.h> 154 #include <linux/module.h> 155 #include <linux/slab.h> 156 #include <linux/pci.h> 157 #include <linux/delay.h> 158 #include <linux/mISDNhw.h> 159 #include <linux/mISDNdsp.h> 160 161 /* 162 #define IRQCOUNT_DEBUG 163 #define IRQ_DEBUG 164 */ 165 166 #include "hfc_multi.h" 167 #ifdef ECHOPREP 168 #include "gaintab.h" 169 #endif 170 171 #define MAX_CARDS 8 172 #define MAX_PORTS (8 * MAX_CARDS) 173 #define MAX_FRAGS (32 * MAX_CARDS) 174 175 static LIST_HEAD(HFClist); 176 static spinlock_t HFClock; /* global hfc list lock */ 177 178 static void ph_state_change(struct dchannel *); 179 180 static struct hfc_multi *syncmaster; 181 static int plxsd_master; /* if we have a master card (yet) */ 182 static spinlock_t plx_lock; /* may not acquire other lock inside */ 183 184 #define TYP_E1 1 185 #define TYP_4S 4 186 #define TYP_8S 8 187 188 static int poll_timer = 6; /* default = 128 samples = 16ms */ 189 /* number of POLL_TIMER interrupts for G2 timeout (ca 1s) */ 190 static int nt_t1_count[] = { 3840, 1920, 960, 480, 240, 120, 60, 30 }; 191 #define CLKDEL_TE 0x0f /* CLKDEL in TE mode */ 192 #define CLKDEL_NT 0x6c /* CLKDEL in NT mode 193 (0x60 MUST be included!) */ 194 195 #define DIP_4S 0x1 /* DIP Switches for Beronet 1S/2S/4S cards */ 196 #define DIP_8S 0x2 /* DIP Switches for Beronet 8S+ cards */ 197 #define DIP_E1 0x3 /* DIP Switches for Beronet E1 cards */ 198 199 /* 200 * module stuff 201 */ 202 203 static uint type[MAX_CARDS]; 204 static int pcm[MAX_CARDS]; 205 static uint dmask[MAX_CARDS]; 206 static uint bmask[MAX_FRAGS]; 207 static uint iomode[MAX_CARDS]; 208 static uint port[MAX_PORTS]; 209 static uint debug; 210 static uint poll; 211 static int clock; 212 static uint timer; 213 static uint clockdelay_te = CLKDEL_TE; 214 static uint clockdelay_nt = CLKDEL_NT; 215 #define HWID_NONE 0 216 #define HWID_MINIP4 1 217 #define HWID_MINIP8 2 218 #define HWID_MINIP16 3 219 static uint hwid = HWID_NONE; 220 221 static int HFC_cnt, E1_cnt, bmask_cnt, Port_cnt, PCM_cnt = 99; 222 223 MODULE_AUTHOR("Andreas Eversberg"); 224 MODULE_LICENSE("GPL"); 225 MODULE_VERSION(HFC_MULTI_VERSION); 226 module_param(debug, uint, S_IRUGO | S_IWUSR); 227 module_param(poll, uint, S_IRUGO | S_IWUSR); 228 module_param(clock, int, S_IRUGO | S_IWUSR); 229 module_param(timer, uint, S_IRUGO | S_IWUSR); 230 module_param(clockdelay_te, uint, S_IRUGO | S_IWUSR); 231 module_param(clockdelay_nt, uint, S_IRUGO | S_IWUSR); 232 module_param_array(type, uint, NULL, S_IRUGO | S_IWUSR); 233 module_param_array(pcm, int, NULL, S_IRUGO | S_IWUSR); 234 module_param_array(dmask, uint, NULL, S_IRUGO | S_IWUSR); 235 module_param_array(bmask, uint, NULL, S_IRUGO | S_IWUSR); 236 module_param_array(iomode, uint, NULL, S_IRUGO | S_IWUSR); 237 module_param_array(port, uint, NULL, S_IRUGO | S_IWUSR); 238 module_param(hwid, uint, S_IRUGO | S_IWUSR); /* The hardware ID */ 239 240 #ifdef HFC_REGISTER_DEBUG 241 #define HFC_outb(hc, reg, val) \ 242 (hc->HFC_outb(hc, reg, val, __func__, __LINE__)) 243 #define HFC_outb_nodebug(hc, reg, val) \ 244 (hc->HFC_outb_nodebug(hc, reg, val, __func__, __LINE__)) 245 #define HFC_inb(hc, reg) \ 246 (hc->HFC_inb(hc, reg, __func__, __LINE__)) 247 #define HFC_inb_nodebug(hc, reg) \ 248 (hc->HFC_inb_nodebug(hc, reg, __func__, __LINE__)) 249 #define HFC_inw(hc, reg) \ 250 (hc->HFC_inw(hc, reg, __func__, __LINE__)) 251 #define HFC_inw_nodebug(hc, reg) \ 252 (hc->HFC_inw_nodebug(hc, reg, __func__, __LINE__)) 253 #define HFC_wait(hc) \ 254 (hc->HFC_wait(hc, __func__, __LINE__)) 255 #define HFC_wait_nodebug(hc) \ 256 (hc->HFC_wait_nodebug(hc, __func__, __LINE__)) 257 #else 258 #define HFC_outb(hc, reg, val) (hc->HFC_outb(hc, reg, val)) 259 #define HFC_outb_nodebug(hc, reg, val) (hc->HFC_outb_nodebug(hc, reg, val)) 260 #define HFC_inb(hc, reg) (hc->HFC_inb(hc, reg)) 261 #define HFC_inb_nodebug(hc, reg) (hc->HFC_inb_nodebug(hc, reg)) 262 #define HFC_inw(hc, reg) (hc->HFC_inw(hc, reg)) 263 #define HFC_inw_nodebug(hc, reg) (hc->HFC_inw_nodebug(hc, reg)) 264 #define HFC_wait(hc) (hc->HFC_wait(hc)) 265 #define HFC_wait_nodebug(hc) (hc->HFC_wait_nodebug(hc)) 266 #endif 267 268 #ifdef CONFIG_MISDN_HFCMULTI_8xx 269 #include "hfc_multi_8xx.h" 270 #endif 271 272 /* HFC_IO_MODE_PCIMEM */ 273 static void 274 #ifdef HFC_REGISTER_DEBUG 275 HFC_outb_pcimem(struct hfc_multi *hc, u_char reg, u_char val, 276 const char *function, int line) 277 #else 278 HFC_outb_pcimem(struct hfc_multi *hc, u_char reg, u_char val) 279 #endif 280 { 281 writeb(val, hc->pci_membase + reg); 282 } 283 static u_char 284 #ifdef HFC_REGISTER_DEBUG 285 HFC_inb_pcimem(struct hfc_multi *hc, u_char reg, const char *function, int line) 286 #else 287 HFC_inb_pcimem(struct hfc_multi *hc, u_char reg) 288 #endif 289 { 290 return readb(hc->pci_membase + reg); 291 } 292 static u_short 293 #ifdef HFC_REGISTER_DEBUG 294 HFC_inw_pcimem(struct hfc_multi *hc, u_char reg, const char *function, int line) 295 #else 296 HFC_inw_pcimem(struct hfc_multi *hc, u_char reg) 297 #endif 298 { 299 return readw(hc->pci_membase + reg); 300 } 301 static void 302 #ifdef HFC_REGISTER_DEBUG 303 HFC_wait_pcimem(struct hfc_multi *hc, const char *function, int line) 304 #else 305 HFC_wait_pcimem(struct hfc_multi *hc) 306 #endif 307 { 308 while (readb(hc->pci_membase + R_STATUS) & V_BUSY) 309 cpu_relax(); 310 } 311 312 /* HFC_IO_MODE_REGIO */ 313 static void 314 #ifdef HFC_REGISTER_DEBUG 315 HFC_outb_regio(struct hfc_multi *hc, u_char reg, u_char val, 316 const char *function, int line) 317 #else 318 HFC_outb_regio(struct hfc_multi *hc, u_char reg, u_char val) 319 #endif 320 { 321 outb(reg, hc->pci_iobase + 4); 322 outb(val, hc->pci_iobase); 323 } 324 static u_char 325 #ifdef HFC_REGISTER_DEBUG 326 HFC_inb_regio(struct hfc_multi *hc, u_char reg, const char *function, int line) 327 #else 328 HFC_inb_regio(struct hfc_multi *hc, u_char reg) 329 #endif 330 { 331 outb(reg, hc->pci_iobase + 4); 332 return inb(hc->pci_iobase); 333 } 334 static u_short 335 #ifdef HFC_REGISTER_DEBUG 336 HFC_inw_regio(struct hfc_multi *hc, u_char reg, const char *function, int line) 337 #else 338 HFC_inw_regio(struct hfc_multi *hc, u_char reg) 339 #endif 340 { 341 outb(reg, hc->pci_iobase + 4); 342 return inw(hc->pci_iobase); 343 } 344 static void 345 #ifdef HFC_REGISTER_DEBUG 346 HFC_wait_regio(struct hfc_multi *hc, const char *function, int line) 347 #else 348 HFC_wait_regio(struct hfc_multi *hc) 349 #endif 350 { 351 outb(R_STATUS, hc->pci_iobase + 4); 352 while (inb(hc->pci_iobase) & V_BUSY) 353 cpu_relax(); 354 } 355 356 #ifdef HFC_REGISTER_DEBUG 357 static void 358 HFC_outb_debug(struct hfc_multi *hc, u_char reg, u_char val, 359 const char *function, int line) 360 { 361 char regname[256] = "", bits[9] = "xxxxxxxx"; 362 int i; 363 364 i = -1; 365 while (hfc_register_names[++i].name) { 366 if (hfc_register_names[i].reg == reg) 367 strcat(regname, hfc_register_names[i].name); 368 } 369 if (regname[0] == '\0') 370 strcpy(regname, "register"); 371 372 bits[7] = '0' + (!!(val & 1)); 373 bits[6] = '0' + (!!(val & 2)); 374 bits[5] = '0' + (!!(val & 4)); 375 bits[4] = '0' + (!!(val & 8)); 376 bits[3] = '0' + (!!(val & 16)); 377 bits[2] = '0' + (!!(val & 32)); 378 bits[1] = '0' + (!!(val & 64)); 379 bits[0] = '0' + (!!(val & 128)); 380 printk(KERN_DEBUG 381 "HFC_outb(chip %d, %02x=%s, 0x%02x=%s); in %s() line %d\n", 382 hc->id, reg, regname, val, bits, function, line); 383 HFC_outb_nodebug(hc, reg, val); 384 } 385 static u_char 386 HFC_inb_debug(struct hfc_multi *hc, u_char reg, const char *function, int line) 387 { 388 char regname[256] = "", bits[9] = "xxxxxxxx"; 389 u_char val = HFC_inb_nodebug(hc, reg); 390 int i; 391 392 i = 0; 393 while (hfc_register_names[i++].name) 394 ; 395 while (hfc_register_names[++i].name) { 396 if (hfc_register_names[i].reg == reg) 397 strcat(regname, hfc_register_names[i].name); 398 } 399 if (regname[0] == '\0') 400 strcpy(regname, "register"); 401 402 bits[7] = '0' + (!!(val & 1)); 403 bits[6] = '0' + (!!(val & 2)); 404 bits[5] = '0' + (!!(val & 4)); 405 bits[4] = '0' + (!!(val & 8)); 406 bits[3] = '0' + (!!(val & 16)); 407 bits[2] = '0' + (!!(val & 32)); 408 bits[1] = '0' + (!!(val & 64)); 409 bits[0] = '0' + (!!(val & 128)); 410 printk(KERN_DEBUG 411 "HFC_inb(chip %d, %02x=%s) = 0x%02x=%s; in %s() line %d\n", 412 hc->id, reg, regname, val, bits, function, line); 413 return val; 414 } 415 static u_short 416 HFC_inw_debug(struct hfc_multi *hc, u_char reg, const char *function, int line) 417 { 418 char regname[256] = ""; 419 u_short val = HFC_inw_nodebug(hc, reg); 420 int i; 421 422 i = 0; 423 while (hfc_register_names[i++].name) 424 ; 425 while (hfc_register_names[++i].name) { 426 if (hfc_register_names[i].reg == reg) 427 strcat(regname, hfc_register_names[i].name); 428 } 429 if (regname[0] == '\0') 430 strcpy(regname, "register"); 431 432 printk(KERN_DEBUG 433 "HFC_inw(chip %d, %02x=%s) = 0x%04x; in %s() line %d\n", 434 hc->id, reg, regname, val, function, line); 435 return val; 436 } 437 static void 438 HFC_wait_debug(struct hfc_multi *hc, const char *function, int line) 439 { 440 printk(KERN_DEBUG "HFC_wait(chip %d); in %s() line %d\n", 441 hc->id, function, line); 442 HFC_wait_nodebug(hc); 443 } 444 #endif 445 446 /* write fifo data (REGIO) */ 447 static void 448 write_fifo_regio(struct hfc_multi *hc, u_char *data, int len) 449 { 450 outb(A_FIFO_DATA0, (hc->pci_iobase) + 4); 451 while (len >> 2) { 452 outl(cpu_to_le32(*(u32 *)data), hc->pci_iobase); 453 data += 4; 454 len -= 4; 455 } 456 while (len >> 1) { 457 outw(cpu_to_le16(*(u16 *)data), hc->pci_iobase); 458 data += 2; 459 len -= 2; 460 } 461 while (len) { 462 outb(*data, hc->pci_iobase); 463 data++; 464 len--; 465 } 466 } 467 /* write fifo data (PCIMEM) */ 468 static void 469 write_fifo_pcimem(struct hfc_multi *hc, u_char *data, int len) 470 { 471 while (len >> 2) { 472 writel(cpu_to_le32(*(u32 *)data), 473 hc->pci_membase + A_FIFO_DATA0); 474 data += 4; 475 len -= 4; 476 } 477 while (len >> 1) { 478 writew(cpu_to_le16(*(u16 *)data), 479 hc->pci_membase + A_FIFO_DATA0); 480 data += 2; 481 len -= 2; 482 } 483 while (len) { 484 writeb(*data, hc->pci_membase + A_FIFO_DATA0); 485 data++; 486 len--; 487 } 488 } 489 490 /* read fifo data (REGIO) */ 491 static void 492 read_fifo_regio(struct hfc_multi *hc, u_char *data, int len) 493 { 494 outb(A_FIFO_DATA0, (hc->pci_iobase) + 4); 495 while (len >> 2) { 496 *(u32 *)data = le32_to_cpu(inl(hc->pci_iobase)); 497 data += 4; 498 len -= 4; 499 } 500 while (len >> 1) { 501 *(u16 *)data = le16_to_cpu(inw(hc->pci_iobase)); 502 data += 2; 503 len -= 2; 504 } 505 while (len) { 506 *data = inb(hc->pci_iobase); 507 data++; 508 len--; 509 } 510 } 511 512 /* read fifo data (PCIMEM) */ 513 static void 514 read_fifo_pcimem(struct hfc_multi *hc, u_char *data, int len) 515 { 516 while (len >> 2) { 517 *(u32 *)data = 518 le32_to_cpu(readl(hc->pci_membase + A_FIFO_DATA0)); 519 data += 4; 520 len -= 4; 521 } 522 while (len >> 1) { 523 *(u16 *)data = 524 le16_to_cpu(readw(hc->pci_membase + A_FIFO_DATA0)); 525 data += 2; 526 len -= 2; 527 } 528 while (len) { 529 *data = readb(hc->pci_membase + A_FIFO_DATA0); 530 data++; 531 len--; 532 } 533 } 534 535 static void 536 enable_hwirq(struct hfc_multi *hc) 537 { 538 hc->hw.r_irq_ctrl |= V_GLOB_IRQ_EN; 539 HFC_outb(hc, R_IRQ_CTRL, hc->hw.r_irq_ctrl); 540 } 541 542 static void 543 disable_hwirq(struct hfc_multi *hc) 544 { 545 hc->hw.r_irq_ctrl &= ~((u_char)V_GLOB_IRQ_EN); 546 HFC_outb(hc, R_IRQ_CTRL, hc->hw.r_irq_ctrl); 547 } 548 549 #define NUM_EC 2 550 #define MAX_TDM_CHAN 32 551 552 553 static inline void 554 enablepcibridge(struct hfc_multi *c) 555 { 556 HFC_outb(c, R_BRG_PCM_CFG, (0x0 << 6) | 0x3); /* was _io before */ 557 } 558 559 static inline void 560 disablepcibridge(struct hfc_multi *c) 561 { 562 HFC_outb(c, R_BRG_PCM_CFG, (0x0 << 6) | 0x2); /* was _io before */ 563 } 564 565 static inline unsigned char 566 readpcibridge(struct hfc_multi *hc, unsigned char address) 567 { 568 unsigned short cipv; 569 unsigned char data; 570 571 if (!hc->pci_iobase) 572 return 0; 573 574 /* slow down a PCI read access by 1 PCI clock cycle */ 575 HFC_outb(hc, R_CTRL, 0x4); /*was _io before*/ 576 577 if (address == 0) 578 cipv = 0x4000; 579 else 580 cipv = 0x5800; 581 582 /* select local bridge port address by writing to CIP port */ 583 /* data = HFC_inb(c, cipv); * was _io before */ 584 outw(cipv, hc->pci_iobase + 4); 585 data = inb(hc->pci_iobase); 586 587 /* restore R_CTRL for normal PCI read cycle speed */ 588 HFC_outb(hc, R_CTRL, 0x0); /* was _io before */ 589 590 return data; 591 } 592 593 static inline void 594 writepcibridge(struct hfc_multi *hc, unsigned char address, unsigned char data) 595 { 596 unsigned short cipv; 597 unsigned int datav; 598 599 if (!hc->pci_iobase) 600 return; 601 602 if (address == 0) 603 cipv = 0x4000; 604 else 605 cipv = 0x5800; 606 607 /* select local bridge port address by writing to CIP port */ 608 outw(cipv, hc->pci_iobase + 4); 609 /* define a 32 bit dword with 4 identical bytes for write sequence */ 610 datav = data | ((__u32) data << 8) | ((__u32) data << 16) | 611 ((__u32) data << 24); 612 613 /* 614 * write this 32 bit dword to the bridge data port 615 * this will initiate a write sequence of up to 4 writes to the same 616 * address on the local bus interface the number of write accesses 617 * is undefined but >=1 and depends on the next PCI transaction 618 * during write sequence on the local bus 619 */ 620 outl(datav, hc->pci_iobase); 621 } 622 623 static inline void 624 cpld_set_reg(struct hfc_multi *hc, unsigned char reg) 625 { 626 /* Do data pin read low byte */ 627 HFC_outb(hc, R_GPIO_OUT1, reg); 628 } 629 630 static inline void 631 cpld_write_reg(struct hfc_multi *hc, unsigned char reg, unsigned char val) 632 { 633 cpld_set_reg(hc, reg); 634 635 enablepcibridge(hc); 636 writepcibridge(hc, 1, val); 637 disablepcibridge(hc); 638 639 return; 640 } 641 642 static inline unsigned char 643 cpld_read_reg(struct hfc_multi *hc, unsigned char reg) 644 { 645 unsigned char bytein; 646 647 cpld_set_reg(hc, reg); 648 649 /* Do data pin read low byte */ 650 HFC_outb(hc, R_GPIO_OUT1, reg); 651 652 enablepcibridge(hc); 653 bytein = readpcibridge(hc, 1); 654 disablepcibridge(hc); 655 656 return bytein; 657 } 658 659 static inline void 660 vpm_write_address(struct hfc_multi *hc, unsigned short addr) 661 { 662 cpld_write_reg(hc, 0, 0xff & addr); 663 cpld_write_reg(hc, 1, 0x01 & (addr >> 8)); 664 } 665 666 static inline unsigned short 667 vpm_read_address(struct hfc_multi *c) 668 { 669 unsigned short addr; 670 unsigned short highbit; 671 672 addr = cpld_read_reg(c, 0); 673 highbit = cpld_read_reg(c, 1); 674 675 addr = addr | (highbit << 8); 676 677 return addr & 0x1ff; 678 } 679 680 static inline unsigned char 681 vpm_in(struct hfc_multi *c, int which, unsigned short addr) 682 { 683 unsigned char res; 684 685 vpm_write_address(c, addr); 686 687 if (!which) 688 cpld_set_reg(c, 2); 689 else 690 cpld_set_reg(c, 3); 691 692 enablepcibridge(c); 693 res = readpcibridge(c, 1); 694 disablepcibridge(c); 695 696 cpld_set_reg(c, 0); 697 698 return res; 699 } 700 701 static inline void 702 vpm_out(struct hfc_multi *c, int which, unsigned short addr, 703 unsigned char data) 704 { 705 vpm_write_address(c, addr); 706 707 enablepcibridge(c); 708 709 if (!which) 710 cpld_set_reg(c, 2); 711 else 712 cpld_set_reg(c, 3); 713 714 writepcibridge(c, 1, data); 715 716 cpld_set_reg(c, 0); 717 718 disablepcibridge(c); 719 720 { 721 unsigned char regin; 722 regin = vpm_in(c, which, addr); 723 if (regin != data) 724 printk(KERN_DEBUG "Wrote 0x%x to register 0x%x but got back " 725 "0x%x\n", data, addr, regin); 726 } 727 728 } 729 730 731 static void 732 vpm_init(struct hfc_multi *wc) 733 { 734 unsigned char reg; 735 unsigned int mask; 736 unsigned int i, x, y; 737 unsigned int ver; 738 739 for (x = 0; x < NUM_EC; x++) { 740 /* Setup GPIO's */ 741 if (!x) { 742 ver = vpm_in(wc, x, 0x1a0); 743 printk(KERN_DEBUG "VPM: Chip %d: ver %02x\n", x, ver); 744 } 745 746 for (y = 0; y < 4; y++) { 747 vpm_out(wc, x, 0x1a8 + y, 0x00); /* GPIO out */ 748 vpm_out(wc, x, 0x1ac + y, 0x00); /* GPIO dir */ 749 vpm_out(wc, x, 0x1b0 + y, 0x00); /* GPIO sel */ 750 } 751 752 /* Setup TDM path - sets fsync and tdm_clk as inputs */ 753 reg = vpm_in(wc, x, 0x1a3); /* misc_con */ 754 vpm_out(wc, x, 0x1a3, reg & ~2); 755 756 /* Setup Echo length (256 taps) */ 757 vpm_out(wc, x, 0x022, 1); 758 vpm_out(wc, x, 0x023, 0xff); 759 760 /* Setup timeslots */ 761 vpm_out(wc, x, 0x02f, 0x00); 762 mask = 0x02020202 << (x * 4); 763 764 /* Setup the tdm channel masks for all chips */ 765 for (i = 0; i < 4; i++) 766 vpm_out(wc, x, 0x33 - i, (mask >> (i << 3)) & 0xff); 767 768 /* Setup convergence rate */ 769 printk(KERN_DEBUG "VPM: A-law mode\n"); 770 reg = 0x00 | 0x10 | 0x01; 771 vpm_out(wc, x, 0x20, reg); 772 printk(KERN_DEBUG "VPM reg 0x20 is %x\n", reg); 773 /*vpm_out(wc, x, 0x20, (0x00 | 0x08 | 0x20 | 0x10)); */ 774 775 vpm_out(wc, x, 0x24, 0x02); 776 reg = vpm_in(wc, x, 0x24); 777 printk(KERN_DEBUG "NLP Thresh is set to %d (0x%x)\n", reg, reg); 778 779 /* Initialize echo cans */ 780 for (i = 0; i < MAX_TDM_CHAN; i++) { 781 if (mask & (0x00000001 << i)) 782 vpm_out(wc, x, i, 0x00); 783 } 784 785 /* 786 * ARM arch at least disallows a udelay of 787 * more than 2ms... it gives a fake "__bad_udelay" 788 * reference at link-time. 789 * long delays in kernel code are pretty sucky anyway 790 * for now work around it using 5 x 2ms instead of 1 x 10ms 791 */ 792 793 udelay(2000); 794 udelay(2000); 795 udelay(2000); 796 udelay(2000); 797 udelay(2000); 798 799 /* Put in bypass mode */ 800 for (i = 0; i < MAX_TDM_CHAN; i++) { 801 if (mask & (0x00000001 << i)) 802 vpm_out(wc, x, i, 0x01); 803 } 804 805 /* Enable bypass */ 806 for (i = 0; i < MAX_TDM_CHAN; i++) { 807 if (mask & (0x00000001 << i)) 808 vpm_out(wc, x, 0x78 + i, 0x01); 809 } 810 811 } 812 } 813 814 #ifdef UNUSED 815 static void 816 vpm_check(struct hfc_multi *hctmp) 817 { 818 unsigned char gpi2; 819 820 gpi2 = HFC_inb(hctmp, R_GPI_IN2); 821 822 if ((gpi2 & 0x3) != 0x3) 823 printk(KERN_DEBUG "Got interrupt 0x%x from VPM!\n", gpi2); 824 } 825 #endif /* UNUSED */ 826 827 828 /* 829 * Interface to enable/disable the HW Echocan 830 * 831 * these functions are called within a spin_lock_irqsave on 832 * the channel instance lock, so we are not disturbed by irqs 833 * 834 * we can later easily change the interface to make other 835 * things configurable, for now we configure the taps 836 * 837 */ 838 839 static void 840 vpm_echocan_on(struct hfc_multi *hc, int ch, int taps) 841 { 842 unsigned int timeslot; 843 unsigned int unit; 844 struct bchannel *bch = hc->chan[ch].bch; 845 #ifdef TXADJ 846 int txadj = -4; 847 struct sk_buff *skb; 848 #endif 849 if (hc->chan[ch].protocol != ISDN_P_B_RAW) 850 return; 851 852 if (!bch) 853 return; 854 855 #ifdef TXADJ 856 skb = _alloc_mISDN_skb(PH_CONTROL_IND, HFC_VOL_CHANGE_TX, 857 sizeof(int), &txadj, GFP_ATOMIC); 858 if (skb) 859 recv_Bchannel_skb(bch, skb); 860 #endif 861 862 timeslot = ((ch / 4) * 8) + ((ch % 4) * 4) + 1; 863 unit = ch % 4; 864 865 printk(KERN_NOTICE "vpm_echocan_on called taps [%d] on timeslot %d\n", 866 taps, timeslot); 867 868 vpm_out(hc, unit, timeslot, 0x7e); 869 } 870 871 static void 872 vpm_echocan_off(struct hfc_multi *hc, int ch) 873 { 874 unsigned int timeslot; 875 unsigned int unit; 876 struct bchannel *bch = hc->chan[ch].bch; 877 #ifdef TXADJ 878 int txadj = 0; 879 struct sk_buff *skb; 880 #endif 881 882 if (hc->chan[ch].protocol != ISDN_P_B_RAW) 883 return; 884 885 if (!bch) 886 return; 887 888 #ifdef TXADJ 889 skb = _alloc_mISDN_skb(PH_CONTROL_IND, HFC_VOL_CHANGE_TX, 890 sizeof(int), &txadj, GFP_ATOMIC); 891 if (skb) 892 recv_Bchannel_skb(bch, skb); 893 #endif 894 895 timeslot = ((ch / 4) * 8) + ((ch % 4) * 4) + 1; 896 unit = ch % 4; 897 898 printk(KERN_NOTICE "vpm_echocan_off called on timeslot %d\n", 899 timeslot); 900 /* FILLME */ 901 vpm_out(hc, unit, timeslot, 0x01); 902 } 903 904 905 /* 906 * Speech Design resync feature 907 * NOTE: This is called sometimes outside interrupt handler. 908 * We must lock irqsave, so no other interrupt (other card) will occur! 909 * Also multiple interrupts may nest, so must lock each access (lists, card)! 910 */ 911 static inline void 912 hfcmulti_resync(struct hfc_multi *locked, struct hfc_multi *newmaster, int rm) 913 { 914 struct hfc_multi *hc, *next, *pcmmaster = NULL; 915 void __iomem *plx_acc_32; 916 u_int pv; 917 u_long flags; 918 919 spin_lock_irqsave(&HFClock, flags); 920 spin_lock(&plx_lock); /* must be locked inside other locks */ 921 922 if (debug & DEBUG_HFCMULTI_PLXSD) 923 printk(KERN_DEBUG "%s: RESYNC(syncmaster=0x%p)\n", 924 __func__, syncmaster); 925 926 /* select new master */ 927 if (newmaster) { 928 if (debug & DEBUG_HFCMULTI_PLXSD) 929 printk(KERN_DEBUG "using provided controller\n"); 930 } else { 931 list_for_each_entry_safe(hc, next, &HFClist, list) { 932 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 933 if (hc->syncronized) { 934 newmaster = hc; 935 break; 936 } 937 } 938 } 939 } 940 941 /* Disable sync of all cards */ 942 list_for_each_entry_safe(hc, next, &HFClist, list) { 943 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 944 plx_acc_32 = hc->plx_membase + PLX_GPIOC; 945 pv = readl(plx_acc_32); 946 pv &= ~PLX_SYNC_O_EN; 947 writel(pv, plx_acc_32); 948 if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip)) { 949 pcmmaster = hc; 950 if (hc->ctype == HFC_TYPE_E1) { 951 if (debug & DEBUG_HFCMULTI_PLXSD) 952 printk(KERN_DEBUG 953 "Schedule SYNC_I\n"); 954 hc->e1_resync |= 1; /* get SYNC_I */ 955 } 956 } 957 } 958 } 959 960 if (newmaster) { 961 hc = newmaster; 962 if (debug & DEBUG_HFCMULTI_PLXSD) 963 printk(KERN_DEBUG "id=%d (0x%p) = syncronized with " 964 "interface.\n", hc->id, hc); 965 /* Enable new sync master */ 966 plx_acc_32 = hc->plx_membase + PLX_GPIOC; 967 pv = readl(plx_acc_32); 968 pv |= PLX_SYNC_O_EN; 969 writel(pv, plx_acc_32); 970 /* switch to jatt PLL, if not disabled by RX_SYNC */ 971 if (hc->ctype == HFC_TYPE_E1 972 && !test_bit(HFC_CHIP_RX_SYNC, &hc->chip)) { 973 if (debug & DEBUG_HFCMULTI_PLXSD) 974 printk(KERN_DEBUG "Schedule jatt PLL\n"); 975 hc->e1_resync |= 2; /* switch to jatt */ 976 } 977 } else { 978 if (pcmmaster) { 979 hc = pcmmaster; 980 if (debug & DEBUG_HFCMULTI_PLXSD) 981 printk(KERN_DEBUG 982 "id=%d (0x%p) = PCM master syncronized " 983 "with QUARTZ\n", hc->id, hc); 984 if (hc->ctype == HFC_TYPE_E1) { 985 /* Use the crystal clock for the PCM 986 master card */ 987 if (debug & DEBUG_HFCMULTI_PLXSD) 988 printk(KERN_DEBUG 989 "Schedule QUARTZ for HFC-E1\n"); 990 hc->e1_resync |= 4; /* switch quartz */ 991 } else { 992 if (debug & DEBUG_HFCMULTI_PLXSD) 993 printk(KERN_DEBUG 994 "QUARTZ is automatically " 995 "enabled by HFC-%dS\n", hc->ctype); 996 } 997 plx_acc_32 = hc->plx_membase + PLX_GPIOC; 998 pv = readl(plx_acc_32); 999 pv |= PLX_SYNC_O_EN; 1000 writel(pv, plx_acc_32); 1001 } else 1002 if (!rm) 1003 printk(KERN_ERR "%s no pcm master, this MUST " 1004 "not happen!\n", __func__); 1005 } 1006 syncmaster = newmaster; 1007 1008 spin_unlock(&plx_lock); 1009 spin_unlock_irqrestore(&HFClock, flags); 1010 } 1011 1012 /* This must be called AND hc must be locked irqsave!!! */ 1013 static inline void 1014 plxsd_checksync(struct hfc_multi *hc, int rm) 1015 { 1016 if (hc->syncronized) { 1017 if (syncmaster == NULL) { 1018 if (debug & DEBUG_HFCMULTI_PLXSD) 1019 printk(KERN_DEBUG "%s: GOT sync on card %d" 1020 " (id=%d)\n", __func__, hc->id + 1, 1021 hc->id); 1022 hfcmulti_resync(hc, hc, rm); 1023 } 1024 } else { 1025 if (syncmaster == hc) { 1026 if (debug & DEBUG_HFCMULTI_PLXSD) 1027 printk(KERN_DEBUG "%s: LOST sync on card %d" 1028 " (id=%d)\n", __func__, hc->id + 1, 1029 hc->id); 1030 hfcmulti_resync(hc, NULL, rm); 1031 } 1032 } 1033 } 1034 1035 1036 /* 1037 * free hardware resources used by driver 1038 */ 1039 static void 1040 release_io_hfcmulti(struct hfc_multi *hc) 1041 { 1042 void __iomem *plx_acc_32; 1043 u_int pv; 1044 u_long plx_flags; 1045 1046 if (debug & DEBUG_HFCMULTI_INIT) 1047 printk(KERN_DEBUG "%s: entered\n", __func__); 1048 1049 /* soft reset also masks all interrupts */ 1050 hc->hw.r_cirm |= V_SRES; 1051 HFC_outb(hc, R_CIRM, hc->hw.r_cirm); 1052 udelay(1000); 1053 hc->hw.r_cirm &= ~V_SRES; 1054 HFC_outb(hc, R_CIRM, hc->hw.r_cirm); 1055 udelay(1000); /* instead of 'wait' that may cause locking */ 1056 1057 /* release Speech Design card, if PLX was initialized */ 1058 if (test_bit(HFC_CHIP_PLXSD, &hc->chip) && hc->plx_membase) { 1059 if (debug & DEBUG_HFCMULTI_PLXSD) 1060 printk(KERN_DEBUG "%s: release PLXSD card %d\n", 1061 __func__, hc->id + 1); 1062 spin_lock_irqsave(&plx_lock, plx_flags); 1063 plx_acc_32 = hc->plx_membase + PLX_GPIOC; 1064 writel(PLX_GPIOC_INIT, plx_acc_32); 1065 pv = readl(plx_acc_32); 1066 /* Termination off */ 1067 pv &= ~PLX_TERM_ON; 1068 /* Disconnect the PCM */ 1069 pv |= PLX_SLAVE_EN_N; 1070 pv &= ~PLX_MASTER_EN; 1071 pv &= ~PLX_SYNC_O_EN; 1072 /* Put the DSP in Reset */ 1073 pv &= ~PLX_DSP_RES_N; 1074 writel(pv, plx_acc_32); 1075 if (debug & DEBUG_HFCMULTI_INIT) 1076 printk(KERN_DEBUG "%s: PCM off: PLX_GPIO=%x\n", 1077 __func__, pv); 1078 spin_unlock_irqrestore(&plx_lock, plx_flags); 1079 } 1080 1081 /* disable memory mapped ports / io ports */ 1082 test_and_clear_bit(HFC_CHIP_PLXSD, &hc->chip); /* prevent resync */ 1083 if (hc->pci_dev) 1084 pci_write_config_word(hc->pci_dev, PCI_COMMAND, 0); 1085 if (hc->pci_membase) 1086 iounmap(hc->pci_membase); 1087 if (hc->plx_membase) 1088 iounmap(hc->plx_membase); 1089 if (hc->pci_iobase) 1090 release_region(hc->pci_iobase, 8); 1091 if (hc->xhfc_membase) 1092 iounmap((void *)hc->xhfc_membase); 1093 1094 if (hc->pci_dev) { 1095 pci_disable_device(hc->pci_dev); 1096 pci_set_drvdata(hc->pci_dev, NULL); 1097 } 1098 if (debug & DEBUG_HFCMULTI_INIT) 1099 printk(KERN_DEBUG "%s: done\n", __func__); 1100 } 1101 1102 /* 1103 * function called to reset the HFC chip. A complete software reset of chip 1104 * and fifos is done. All configuration of the chip is done. 1105 */ 1106 1107 static int 1108 init_chip(struct hfc_multi *hc) 1109 { 1110 u_long flags, val, val2 = 0, rev; 1111 int i, err = 0; 1112 u_char r_conf_en, rval; 1113 void __iomem *plx_acc_32; 1114 u_int pv; 1115 u_long plx_flags, hfc_flags; 1116 int plx_count; 1117 struct hfc_multi *pos, *next, *plx_last_hc; 1118 1119 spin_lock_irqsave(&hc->lock, flags); 1120 /* reset all registers */ 1121 memset(&hc->hw, 0, sizeof(struct hfcm_hw)); 1122 1123 /* revision check */ 1124 if (debug & DEBUG_HFCMULTI_INIT) 1125 printk(KERN_DEBUG "%s: entered\n", __func__); 1126 val = HFC_inb(hc, R_CHIP_ID); 1127 if ((val >> 4) != 0x8 && (val >> 4) != 0xc && (val >> 4) != 0xe && 1128 (val >> 1) != 0x31) { 1129 printk(KERN_INFO "HFC_multi: unknown CHIP_ID:%x\n", (u_int)val); 1130 err = -EIO; 1131 goto out; 1132 } 1133 rev = HFC_inb(hc, R_CHIP_RV); 1134 printk(KERN_INFO 1135 "HFC_multi: detected HFC with chip ID=0x%lx revision=%ld%s\n", 1136 val, rev, (rev == 0 && (hc->ctype != HFC_TYPE_XHFC)) ? 1137 " (old FIFO handling)" : ""); 1138 if (hc->ctype != HFC_TYPE_XHFC && rev == 0) { 1139 test_and_set_bit(HFC_CHIP_REVISION0, &hc->chip); 1140 printk(KERN_WARNING 1141 "HFC_multi: NOTE: Your chip is revision 0, " 1142 "ask Cologne Chip for update. Newer chips " 1143 "have a better FIFO handling. Old chips " 1144 "still work but may have slightly lower " 1145 "HDLC transmit performance.\n"); 1146 } 1147 if (rev > 1) { 1148 printk(KERN_WARNING "HFC_multi: WARNING: This driver doesn't " 1149 "consider chip revision = %ld. The chip / " 1150 "bridge may not work.\n", rev); 1151 } 1152 1153 /* set s-ram size */ 1154 hc->Flen = 0x10; 1155 hc->Zmin = 0x80; 1156 hc->Zlen = 384; 1157 hc->DTMFbase = 0x1000; 1158 if (test_bit(HFC_CHIP_EXRAM_128, &hc->chip)) { 1159 if (debug & DEBUG_HFCMULTI_INIT) 1160 printk(KERN_DEBUG "%s: changing to 128K external RAM\n", 1161 __func__); 1162 hc->hw.r_ctrl |= V_EXT_RAM; 1163 hc->hw.r_ram_sz = 1; 1164 hc->Flen = 0x20; 1165 hc->Zmin = 0xc0; 1166 hc->Zlen = 1856; 1167 hc->DTMFbase = 0x2000; 1168 } 1169 if (test_bit(HFC_CHIP_EXRAM_512, &hc->chip)) { 1170 if (debug & DEBUG_HFCMULTI_INIT) 1171 printk(KERN_DEBUG "%s: changing to 512K external RAM\n", 1172 __func__); 1173 hc->hw.r_ctrl |= V_EXT_RAM; 1174 hc->hw.r_ram_sz = 2; 1175 hc->Flen = 0x20; 1176 hc->Zmin = 0xc0; 1177 hc->Zlen = 8000; 1178 hc->DTMFbase = 0x2000; 1179 } 1180 if (hc->ctype == HFC_TYPE_XHFC) { 1181 hc->Flen = 0x8; 1182 hc->Zmin = 0x0; 1183 hc->Zlen = 64; 1184 hc->DTMFbase = 0x0; 1185 } 1186 hc->max_trans = poll << 1; 1187 if (hc->max_trans > hc->Zlen) 1188 hc->max_trans = hc->Zlen; 1189 1190 /* Speech Design PLX bridge */ 1191 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 1192 if (debug & DEBUG_HFCMULTI_PLXSD) 1193 printk(KERN_DEBUG "%s: initializing PLXSD card %d\n", 1194 __func__, hc->id + 1); 1195 spin_lock_irqsave(&plx_lock, plx_flags); 1196 plx_acc_32 = hc->plx_membase + PLX_GPIOC; 1197 writel(PLX_GPIOC_INIT, plx_acc_32); 1198 pv = readl(plx_acc_32); 1199 /* The first and the last cards are terminating the PCM bus */ 1200 pv |= PLX_TERM_ON; /* hc is currently the last */ 1201 /* Disconnect the PCM */ 1202 pv |= PLX_SLAVE_EN_N; 1203 pv &= ~PLX_MASTER_EN; 1204 pv &= ~PLX_SYNC_O_EN; 1205 /* Put the DSP in Reset */ 1206 pv &= ~PLX_DSP_RES_N; 1207 writel(pv, plx_acc_32); 1208 spin_unlock_irqrestore(&plx_lock, plx_flags); 1209 if (debug & DEBUG_HFCMULTI_INIT) 1210 printk(KERN_DEBUG "%s: slave/term: PLX_GPIO=%x\n", 1211 __func__, pv); 1212 /* 1213 * If we are the 3rd PLXSD card or higher, we must turn 1214 * termination of last PLXSD card off. 1215 */ 1216 spin_lock_irqsave(&HFClock, hfc_flags); 1217 plx_count = 0; 1218 plx_last_hc = NULL; 1219 list_for_each_entry_safe(pos, next, &HFClist, list) { 1220 if (test_bit(HFC_CHIP_PLXSD, &pos->chip)) { 1221 plx_count++; 1222 if (pos != hc) 1223 plx_last_hc = pos; 1224 } 1225 } 1226 if (plx_count >= 3) { 1227 if (debug & DEBUG_HFCMULTI_PLXSD) 1228 printk(KERN_DEBUG "%s: card %d is between, so " 1229 "we disable termination\n", 1230 __func__, plx_last_hc->id + 1); 1231 spin_lock_irqsave(&plx_lock, plx_flags); 1232 plx_acc_32 = plx_last_hc->plx_membase + PLX_GPIOC; 1233 pv = readl(plx_acc_32); 1234 pv &= ~PLX_TERM_ON; 1235 writel(pv, plx_acc_32); 1236 spin_unlock_irqrestore(&plx_lock, plx_flags); 1237 if (debug & DEBUG_HFCMULTI_INIT) 1238 printk(KERN_DEBUG 1239 "%s: term off: PLX_GPIO=%x\n", 1240 __func__, pv); 1241 } 1242 spin_unlock_irqrestore(&HFClock, hfc_flags); 1243 hc->hw.r_pcm_md0 = V_F0_LEN; /* shift clock for DSP */ 1244 } 1245 1246 if (test_bit(HFC_CHIP_EMBSD, &hc->chip)) 1247 hc->hw.r_pcm_md0 = V_F0_LEN; /* shift clock for DSP */ 1248 1249 /* we only want the real Z2 read-pointer for revision > 0 */ 1250 if (!test_bit(HFC_CHIP_REVISION0, &hc->chip)) 1251 hc->hw.r_ram_sz |= V_FZ_MD; 1252 1253 /* select pcm mode */ 1254 if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) { 1255 if (debug & DEBUG_HFCMULTI_INIT) 1256 printk(KERN_DEBUG "%s: setting PCM into slave mode\n", 1257 __func__); 1258 } else 1259 if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip) && !plxsd_master) { 1260 if (debug & DEBUG_HFCMULTI_INIT) 1261 printk(KERN_DEBUG "%s: setting PCM into master mode\n", 1262 __func__); 1263 hc->hw.r_pcm_md0 |= V_PCM_MD; 1264 } else { 1265 if (debug & DEBUG_HFCMULTI_INIT) 1266 printk(KERN_DEBUG "%s: performing PCM auto detect\n", 1267 __func__); 1268 } 1269 1270 /* soft reset */ 1271 HFC_outb(hc, R_CTRL, hc->hw.r_ctrl); 1272 if (hc->ctype == HFC_TYPE_XHFC) 1273 HFC_outb(hc, 0x0C /* R_FIFO_THRES */, 1274 0x11 /* 16 Bytes TX/RX */); 1275 else 1276 HFC_outb(hc, R_RAM_SZ, hc->hw.r_ram_sz); 1277 HFC_outb(hc, R_FIFO_MD, 0); 1278 if (hc->ctype == HFC_TYPE_XHFC) 1279 hc->hw.r_cirm = V_SRES | V_HFCRES | V_PCMRES | V_STRES; 1280 else 1281 hc->hw.r_cirm = V_SRES | V_HFCRES | V_PCMRES | V_STRES 1282 | V_RLD_EPR; 1283 HFC_outb(hc, R_CIRM, hc->hw.r_cirm); 1284 udelay(100); 1285 hc->hw.r_cirm = 0; 1286 HFC_outb(hc, R_CIRM, hc->hw.r_cirm); 1287 udelay(100); 1288 if (hc->ctype != HFC_TYPE_XHFC) 1289 HFC_outb(hc, R_RAM_SZ, hc->hw.r_ram_sz); 1290 1291 /* Speech Design PLX bridge pcm and sync mode */ 1292 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 1293 spin_lock_irqsave(&plx_lock, plx_flags); 1294 plx_acc_32 = hc->plx_membase + PLX_GPIOC; 1295 pv = readl(plx_acc_32); 1296 /* Connect PCM */ 1297 if (hc->hw.r_pcm_md0 & V_PCM_MD) { 1298 pv |= PLX_MASTER_EN | PLX_SLAVE_EN_N; 1299 pv |= PLX_SYNC_O_EN; 1300 if (debug & DEBUG_HFCMULTI_INIT) 1301 printk(KERN_DEBUG "%s: master: PLX_GPIO=%x\n", 1302 __func__, pv); 1303 } else { 1304 pv &= ~(PLX_MASTER_EN | PLX_SLAVE_EN_N); 1305 pv &= ~PLX_SYNC_O_EN; 1306 if (debug & DEBUG_HFCMULTI_INIT) 1307 printk(KERN_DEBUG "%s: slave: PLX_GPIO=%x\n", 1308 __func__, pv); 1309 } 1310 writel(pv, plx_acc_32); 1311 spin_unlock_irqrestore(&plx_lock, plx_flags); 1312 } 1313 1314 /* PCM setup */ 1315 HFC_outb(hc, R_PCM_MD0, hc->hw.r_pcm_md0 | 0x90); 1316 if (hc->slots == 32) 1317 HFC_outb(hc, R_PCM_MD1, 0x00); 1318 if (hc->slots == 64) 1319 HFC_outb(hc, R_PCM_MD1, 0x10); 1320 if (hc->slots == 128) 1321 HFC_outb(hc, R_PCM_MD1, 0x20); 1322 HFC_outb(hc, R_PCM_MD0, hc->hw.r_pcm_md0 | 0xa0); 1323 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) 1324 HFC_outb(hc, R_PCM_MD2, V_SYNC_SRC); /* sync via SYNC_I / O */ 1325 else if (test_bit(HFC_CHIP_EMBSD, &hc->chip)) 1326 HFC_outb(hc, R_PCM_MD2, 0x10); /* V_C2O_EN */ 1327 else 1328 HFC_outb(hc, R_PCM_MD2, 0x00); /* sync from interface */ 1329 HFC_outb(hc, R_PCM_MD0, hc->hw.r_pcm_md0 | 0x00); 1330 for (i = 0; i < 256; i++) { 1331 HFC_outb_nodebug(hc, R_SLOT, i); 1332 HFC_outb_nodebug(hc, A_SL_CFG, 0); 1333 if (hc->ctype != HFC_TYPE_XHFC) 1334 HFC_outb_nodebug(hc, A_CONF, 0); 1335 hc->slot_owner[i] = -1; 1336 } 1337 1338 /* set clock speed */ 1339 if (test_bit(HFC_CHIP_CLOCK2, &hc->chip)) { 1340 if (debug & DEBUG_HFCMULTI_INIT) 1341 printk(KERN_DEBUG 1342 "%s: setting double clock\n", __func__); 1343 HFC_outb(hc, R_BRG_PCM_CFG, V_PCM_CLK); 1344 } 1345 1346 if (test_bit(HFC_CHIP_EMBSD, &hc->chip)) 1347 HFC_outb(hc, 0x02 /* R_CLK_CFG */, 0x40 /* V_CLKO_OFF */); 1348 1349 /* B410P GPIO */ 1350 if (test_bit(HFC_CHIP_B410P, &hc->chip)) { 1351 printk(KERN_NOTICE "Setting GPIOs\n"); 1352 HFC_outb(hc, R_GPIO_SEL, 0x30); 1353 HFC_outb(hc, R_GPIO_EN1, 0x3); 1354 udelay(1000); 1355 printk(KERN_NOTICE "calling vpm_init\n"); 1356 vpm_init(hc); 1357 } 1358 1359 /* check if R_F0_CNT counts (8 kHz frame count) */ 1360 val = HFC_inb(hc, R_F0_CNTL); 1361 val += HFC_inb(hc, R_F0_CNTH) << 8; 1362 if (debug & DEBUG_HFCMULTI_INIT) 1363 printk(KERN_DEBUG 1364 "HFC_multi F0_CNT %ld after reset\n", val); 1365 spin_unlock_irqrestore(&hc->lock, flags); 1366 set_current_state(TASK_UNINTERRUPTIBLE); 1367 schedule_timeout((HZ / 100) ? : 1); /* Timeout minimum 10ms */ 1368 spin_lock_irqsave(&hc->lock, flags); 1369 val2 = HFC_inb(hc, R_F0_CNTL); 1370 val2 += HFC_inb(hc, R_F0_CNTH) << 8; 1371 if (debug & DEBUG_HFCMULTI_INIT) 1372 printk(KERN_DEBUG 1373 "HFC_multi F0_CNT %ld after 10 ms (1st try)\n", 1374 val2); 1375 if (val2 >= val + 8) { /* 1 ms */ 1376 /* it counts, so we keep the pcm mode */ 1377 if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip)) 1378 printk(KERN_INFO "controller is PCM bus MASTER\n"); 1379 else 1380 if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) 1381 printk(KERN_INFO "controller is PCM bus SLAVE\n"); 1382 else { 1383 test_and_set_bit(HFC_CHIP_PCM_SLAVE, &hc->chip); 1384 printk(KERN_INFO "controller is PCM bus SLAVE " 1385 "(auto detected)\n"); 1386 } 1387 } else { 1388 /* does not count */ 1389 if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip)) { 1390 controller_fail: 1391 printk(KERN_ERR "HFC_multi ERROR, getting no 125us " 1392 "pulse. Seems that controller fails.\n"); 1393 err = -EIO; 1394 goto out; 1395 } 1396 if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) { 1397 printk(KERN_INFO "controller is PCM bus SLAVE " 1398 "(ignoring missing PCM clock)\n"); 1399 } else { 1400 /* only one pcm master */ 1401 if (test_bit(HFC_CHIP_PLXSD, &hc->chip) 1402 && plxsd_master) { 1403 printk(KERN_ERR "HFC_multi ERROR, no clock " 1404 "on another Speech Design card found. " 1405 "Please be sure to connect PCM cable.\n"); 1406 err = -EIO; 1407 goto out; 1408 } 1409 /* retry with master clock */ 1410 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 1411 spin_lock_irqsave(&plx_lock, plx_flags); 1412 plx_acc_32 = hc->plx_membase + PLX_GPIOC; 1413 pv = readl(plx_acc_32); 1414 pv |= PLX_MASTER_EN | PLX_SLAVE_EN_N; 1415 pv |= PLX_SYNC_O_EN; 1416 writel(pv, plx_acc_32); 1417 spin_unlock_irqrestore(&plx_lock, plx_flags); 1418 if (debug & DEBUG_HFCMULTI_INIT) 1419 printk(KERN_DEBUG "%s: master: " 1420 "PLX_GPIO=%x\n", __func__, pv); 1421 } 1422 hc->hw.r_pcm_md0 |= V_PCM_MD; 1423 HFC_outb(hc, R_PCM_MD0, hc->hw.r_pcm_md0 | 0x00); 1424 spin_unlock_irqrestore(&hc->lock, flags); 1425 set_current_state(TASK_UNINTERRUPTIBLE); 1426 schedule_timeout((HZ / 100) ?: 1); /* Timeout min. 10ms */ 1427 spin_lock_irqsave(&hc->lock, flags); 1428 val2 = HFC_inb(hc, R_F0_CNTL); 1429 val2 += HFC_inb(hc, R_F0_CNTH) << 8; 1430 if (debug & DEBUG_HFCMULTI_INIT) 1431 printk(KERN_DEBUG "HFC_multi F0_CNT %ld after " 1432 "10 ms (2nd try)\n", val2); 1433 if (val2 >= val + 8) { /* 1 ms */ 1434 test_and_set_bit(HFC_CHIP_PCM_MASTER, 1435 &hc->chip); 1436 printk(KERN_INFO "controller is PCM bus MASTER " 1437 "(auto detected)\n"); 1438 } else 1439 goto controller_fail; 1440 } 1441 } 1442 1443 /* Release the DSP Reset */ 1444 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 1445 if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip)) 1446 plxsd_master = 1; 1447 spin_lock_irqsave(&plx_lock, plx_flags); 1448 plx_acc_32 = hc->plx_membase + PLX_GPIOC; 1449 pv = readl(plx_acc_32); 1450 pv |= PLX_DSP_RES_N; 1451 writel(pv, plx_acc_32); 1452 spin_unlock_irqrestore(&plx_lock, plx_flags); 1453 if (debug & DEBUG_HFCMULTI_INIT) 1454 printk(KERN_DEBUG "%s: reset off: PLX_GPIO=%x\n", 1455 __func__, pv); 1456 } 1457 1458 /* pcm id */ 1459 if (hc->pcm) 1460 printk(KERN_INFO "controller has given PCM BUS ID %d\n", 1461 hc->pcm); 1462 else { 1463 if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip) 1464 || test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 1465 PCM_cnt++; /* SD has proprietary bridging */ 1466 } 1467 hc->pcm = PCM_cnt; 1468 printk(KERN_INFO "controller has PCM BUS ID %d " 1469 "(auto selected)\n", hc->pcm); 1470 } 1471 1472 /* set up timer */ 1473 HFC_outb(hc, R_TI_WD, poll_timer); 1474 hc->hw.r_irqmsk_misc |= V_TI_IRQMSK; 1475 1476 /* set E1 state machine IRQ */ 1477 if (hc->ctype == HFC_TYPE_E1) 1478 hc->hw.r_irqmsk_misc |= V_STA_IRQMSK; 1479 1480 /* set DTMF detection */ 1481 if (test_bit(HFC_CHIP_DTMF, &hc->chip)) { 1482 if (debug & DEBUG_HFCMULTI_INIT) 1483 printk(KERN_DEBUG "%s: enabling DTMF detection " 1484 "for all B-channel\n", __func__); 1485 hc->hw.r_dtmf = V_DTMF_EN | V_DTMF_STOP; 1486 if (test_bit(HFC_CHIP_ULAW, &hc->chip)) 1487 hc->hw.r_dtmf |= V_ULAW_SEL; 1488 HFC_outb(hc, R_DTMF_N, 102 - 1); 1489 hc->hw.r_irqmsk_misc |= V_DTMF_IRQMSK; 1490 } 1491 1492 /* conference engine */ 1493 if (test_bit(HFC_CHIP_ULAW, &hc->chip)) 1494 r_conf_en = V_CONF_EN | V_ULAW; 1495 else 1496 r_conf_en = V_CONF_EN; 1497 if (hc->ctype != HFC_TYPE_XHFC) 1498 HFC_outb(hc, R_CONF_EN, r_conf_en); 1499 1500 /* setting leds */ 1501 switch (hc->leds) { 1502 case 1: /* HFC-E1 OEM */ 1503 if (test_bit(HFC_CHIP_WATCHDOG, &hc->chip)) 1504 HFC_outb(hc, R_GPIO_SEL, 0x32); 1505 else 1506 HFC_outb(hc, R_GPIO_SEL, 0x30); 1507 1508 HFC_outb(hc, R_GPIO_EN1, 0x0f); 1509 HFC_outb(hc, R_GPIO_OUT1, 0x00); 1510 1511 HFC_outb(hc, R_GPIO_EN0, V_GPIO_EN2 | V_GPIO_EN3); 1512 break; 1513 1514 case 2: /* HFC-4S OEM */ 1515 case 3: 1516 HFC_outb(hc, R_GPIO_SEL, 0xf0); 1517 HFC_outb(hc, R_GPIO_EN1, 0xff); 1518 HFC_outb(hc, R_GPIO_OUT1, 0x00); 1519 break; 1520 } 1521 1522 if (test_bit(HFC_CHIP_EMBSD, &hc->chip)) { 1523 hc->hw.r_st_sync = 0x10; /* V_AUTO_SYNCI */ 1524 HFC_outb(hc, R_ST_SYNC, hc->hw.r_st_sync); 1525 } 1526 1527 /* set master clock */ 1528 if (hc->masterclk >= 0) { 1529 if (debug & DEBUG_HFCMULTI_INIT) 1530 printk(KERN_DEBUG "%s: setting ST master clock " 1531 "to port %d (0..%d)\n", 1532 __func__, hc->masterclk, hc->ports - 1); 1533 hc->hw.r_st_sync |= (hc->masterclk | V_AUTO_SYNC); 1534 HFC_outb(hc, R_ST_SYNC, hc->hw.r_st_sync); 1535 } 1536 1537 1538 1539 /* setting misc irq */ 1540 HFC_outb(hc, R_IRQMSK_MISC, hc->hw.r_irqmsk_misc); 1541 if (debug & DEBUG_HFCMULTI_INIT) 1542 printk(KERN_DEBUG "r_irqmsk_misc.2: 0x%x\n", 1543 hc->hw.r_irqmsk_misc); 1544 1545 /* RAM access test */ 1546 HFC_outb(hc, R_RAM_ADDR0, 0); 1547 HFC_outb(hc, R_RAM_ADDR1, 0); 1548 HFC_outb(hc, R_RAM_ADDR2, 0); 1549 for (i = 0; i < 256; i++) { 1550 HFC_outb_nodebug(hc, R_RAM_ADDR0, i); 1551 HFC_outb_nodebug(hc, R_RAM_DATA, ((i * 3) & 0xff)); 1552 } 1553 for (i = 0; i < 256; i++) { 1554 HFC_outb_nodebug(hc, R_RAM_ADDR0, i); 1555 HFC_inb_nodebug(hc, R_RAM_DATA); 1556 rval = HFC_inb_nodebug(hc, R_INT_DATA); 1557 if (rval != ((i * 3) & 0xff)) { 1558 printk(KERN_DEBUG 1559 "addr:%x val:%x should:%x\n", i, rval, 1560 (i * 3) & 0xff); 1561 err++; 1562 } 1563 } 1564 if (err) { 1565 printk(KERN_DEBUG "aborting - %d RAM access errors\n", err); 1566 err = -EIO; 1567 goto out; 1568 } 1569 1570 if (debug & DEBUG_HFCMULTI_INIT) 1571 printk(KERN_DEBUG "%s: done\n", __func__); 1572 out: 1573 spin_unlock_irqrestore(&hc->lock, flags); 1574 return err; 1575 } 1576 1577 1578 /* 1579 * control the watchdog 1580 */ 1581 static void 1582 hfcmulti_watchdog(struct hfc_multi *hc) 1583 { 1584 hc->wdcount++; 1585 1586 if (hc->wdcount > 10) { 1587 hc->wdcount = 0; 1588 hc->wdbyte = hc->wdbyte == V_GPIO_OUT2 ? 1589 V_GPIO_OUT3 : V_GPIO_OUT2; 1590 1591 /* printk("Sending Watchdog Kill %x\n",hc->wdbyte); */ 1592 HFC_outb(hc, R_GPIO_EN0, V_GPIO_EN2 | V_GPIO_EN3); 1593 HFC_outb(hc, R_GPIO_OUT0, hc->wdbyte); 1594 } 1595 } 1596 1597 1598 1599 /* 1600 * output leds 1601 */ 1602 static void 1603 hfcmulti_leds(struct hfc_multi *hc) 1604 { 1605 unsigned long lled; 1606 unsigned long leddw; 1607 int i, state, active, leds; 1608 struct dchannel *dch; 1609 int led[4]; 1610 1611 switch (hc->leds) { 1612 case 1: /* HFC-E1 OEM */ 1613 /* 2 red steady: LOS 1614 * 1 red steady: L1 not active 1615 * 2 green steady: L1 active 1616 * 1st green flashing: activity on TX 1617 * 2nd green flashing: activity on RX 1618 */ 1619 led[0] = 0; 1620 led[1] = 0; 1621 led[2] = 0; 1622 led[3] = 0; 1623 dch = hc->chan[hc->dnum[0]].dch; 1624 if (dch) { 1625 if (hc->chan[hc->dnum[0]].los) 1626 led[1] = 1; 1627 if (hc->e1_state != 1) { 1628 led[0] = 1; 1629 hc->flash[2] = 0; 1630 hc->flash[3] = 0; 1631 } else { 1632 led[2] = 1; 1633 led[3] = 1; 1634 if (!hc->flash[2] && hc->activity_tx) 1635 hc->flash[2] = poll; 1636 if (!hc->flash[3] && hc->activity_rx) 1637 hc->flash[3] = poll; 1638 if (hc->flash[2] && hc->flash[2] < 1024) 1639 led[2] = 0; 1640 if (hc->flash[3] && hc->flash[3] < 1024) 1641 led[3] = 0; 1642 if (hc->flash[2] >= 2048) 1643 hc->flash[2] = 0; 1644 if (hc->flash[3] >= 2048) 1645 hc->flash[3] = 0; 1646 if (hc->flash[2]) 1647 hc->flash[2] += poll; 1648 if (hc->flash[3]) 1649 hc->flash[3] += poll; 1650 } 1651 } 1652 leds = (led[0] | (led[1]<<2) | (led[2]<<1) | (led[3]<<3))^0xF; 1653 /* leds are inverted */ 1654 if (leds != (int)hc->ledstate) { 1655 HFC_outb_nodebug(hc, R_GPIO_OUT1, leds); 1656 hc->ledstate = leds; 1657 } 1658 break; 1659 1660 case 2: /* HFC-4S OEM */ 1661 /* red steady: PH_DEACTIVATE 1662 * green steady: PH_ACTIVATE 1663 * green flashing: activity on TX 1664 */ 1665 for (i = 0; i < 4; i++) { 1666 state = 0; 1667 active = -1; 1668 dch = hc->chan[(i << 2) | 2].dch; 1669 if (dch) { 1670 state = dch->state; 1671 if (dch->dev.D.protocol == ISDN_P_NT_S0) 1672 active = 3; 1673 else 1674 active = 7; 1675 } 1676 if (state) { 1677 if (state == active) { 1678 led[i] = 1; /* led green */ 1679 hc->activity_tx |= hc->activity_rx; 1680 if (!hc->flash[i] && 1681 (hc->activity_tx & (1 << i))) 1682 hc->flash[i] = poll; 1683 if (hc->flash[i] && hc->flash[i] < 1024) 1684 led[i] = 0; /* led off */ 1685 if (hc->flash[i] >= 2048) 1686 hc->flash[i] = 0; 1687 if (hc->flash[i]) 1688 hc->flash[i] += poll; 1689 } else { 1690 led[i] = 2; /* led red */ 1691 hc->flash[i] = 0; 1692 } 1693 } else 1694 led[i] = 0; /* led off */ 1695 } 1696 if (test_bit(HFC_CHIP_B410P, &hc->chip)) { 1697 leds = 0; 1698 for (i = 0; i < 4; i++) { 1699 if (led[i] == 1) { 1700 /*green*/ 1701 leds |= (0x2 << (i * 2)); 1702 } else if (led[i] == 2) { 1703 /*red*/ 1704 leds |= (0x1 << (i * 2)); 1705 } 1706 } 1707 if (leds != (int)hc->ledstate) { 1708 vpm_out(hc, 0, 0x1a8 + 3, leds); 1709 hc->ledstate = leds; 1710 } 1711 } else { 1712 leds = ((led[3] > 0) << 0) | ((led[1] > 0) << 1) | 1713 ((led[0] > 0) << 2) | ((led[2] > 0) << 3) | 1714 ((led[3] & 1) << 4) | ((led[1] & 1) << 5) | 1715 ((led[0] & 1) << 6) | ((led[2] & 1) << 7); 1716 if (leds != (int)hc->ledstate) { 1717 HFC_outb_nodebug(hc, R_GPIO_EN1, leds & 0x0F); 1718 HFC_outb_nodebug(hc, R_GPIO_OUT1, leds >> 4); 1719 hc->ledstate = leds; 1720 } 1721 } 1722 break; 1723 1724 case 3: /* HFC 1S/2S Beronet */ 1725 /* red steady: PH_DEACTIVATE 1726 * green steady: PH_ACTIVATE 1727 * green flashing: activity on TX 1728 */ 1729 for (i = 0; i < 2; i++) { 1730 state = 0; 1731 active = -1; 1732 dch = hc->chan[(i << 2) | 2].dch; 1733 if (dch) { 1734 state = dch->state; 1735 if (dch->dev.D.protocol == ISDN_P_NT_S0) 1736 active = 3; 1737 else 1738 active = 7; 1739 } 1740 if (state) { 1741 if (state == active) { 1742 led[i] = 1; /* led green */ 1743 hc->activity_tx |= hc->activity_rx; 1744 if (!hc->flash[i] && 1745 (hc->activity_tx & (1 << i))) 1746 hc->flash[i] = poll; 1747 if (hc->flash[i] < 1024) 1748 led[i] = 0; /* led off */ 1749 if (hc->flash[i] >= 2048) 1750 hc->flash[i] = 0; 1751 if (hc->flash[i]) 1752 hc->flash[i] += poll; 1753 } else { 1754 led[i] = 2; /* led red */ 1755 hc->flash[i] = 0; 1756 } 1757 } else 1758 led[i] = 0; /* led off */ 1759 } 1760 leds = (led[0] > 0) | ((led[1] > 0) << 1) | ((led[0]&1) << 2) 1761 | ((led[1]&1) << 3); 1762 if (leds != (int)hc->ledstate) { 1763 HFC_outb_nodebug(hc, R_GPIO_EN1, 1764 ((led[0] > 0) << 2) | ((led[1] > 0) << 3)); 1765 HFC_outb_nodebug(hc, R_GPIO_OUT1, 1766 ((led[0] & 1) << 2) | ((led[1] & 1) << 3)); 1767 hc->ledstate = leds; 1768 } 1769 break; 1770 case 8: /* HFC 8S+ Beronet */ 1771 /* off: PH_DEACTIVATE 1772 * steady: PH_ACTIVATE 1773 * flashing: activity on TX 1774 */ 1775 lled = 0xff; /* leds off */ 1776 for (i = 0; i < 8; i++) { 1777 state = 0; 1778 active = -1; 1779 dch = hc->chan[(i << 2) | 2].dch; 1780 if (dch) { 1781 state = dch->state; 1782 if (dch->dev.D.protocol == ISDN_P_NT_S0) 1783 active = 3; 1784 else 1785 active = 7; 1786 } 1787 if (state) { 1788 if (state == active) { 1789 lled &= ~(1 << i); /* led on */ 1790 hc->activity_tx |= hc->activity_rx; 1791 if (!hc->flash[i] && 1792 (hc->activity_tx & (1 << i))) 1793 hc->flash[i] = poll; 1794 if (hc->flash[i] < 1024) 1795 lled |= 1 << i; /* led off */ 1796 if (hc->flash[i] >= 2048) 1797 hc->flash[i] = 0; 1798 if (hc->flash[i]) 1799 hc->flash[i] += poll; 1800 } else 1801 hc->flash[i] = 0; 1802 } 1803 } 1804 leddw = lled << 24 | lled << 16 | lled << 8 | lled; 1805 if (leddw != hc->ledstate) { 1806 /* HFC_outb(hc, R_BRG_PCM_CFG, 1); 1807 HFC_outb(c, R_BRG_PCM_CFG, (0x0 << 6) | 0x3); */ 1808 /* was _io before */ 1809 HFC_outb_nodebug(hc, R_BRG_PCM_CFG, 1 | V_PCM_CLK); 1810 outw(0x4000, hc->pci_iobase + 4); 1811 outl(leddw, hc->pci_iobase); 1812 HFC_outb_nodebug(hc, R_BRG_PCM_CFG, V_PCM_CLK); 1813 hc->ledstate = leddw; 1814 } 1815 break; 1816 } 1817 hc->activity_tx = 0; 1818 hc->activity_rx = 0; 1819 } 1820 /* 1821 * read dtmf coefficients 1822 */ 1823 1824 static void 1825 hfcmulti_dtmf(struct hfc_multi *hc) 1826 { 1827 s32 *coeff; 1828 u_int mantissa; 1829 int co, ch; 1830 struct bchannel *bch = NULL; 1831 u8 exponent; 1832 int dtmf = 0; 1833 int addr; 1834 u16 w_float; 1835 struct sk_buff *skb; 1836 struct mISDNhead *hh; 1837 1838 if (debug & DEBUG_HFCMULTI_DTMF) 1839 printk(KERN_DEBUG "%s: dtmf detection irq\n", __func__); 1840 for (ch = 0; ch <= 31; ch++) { 1841 /* only process enabled B-channels */ 1842 bch = hc->chan[ch].bch; 1843 if (!bch) 1844 continue; 1845 if (!hc->created[hc->chan[ch].port]) 1846 continue; 1847 if (!test_bit(FLG_TRANSPARENT, &bch->Flags)) 1848 continue; 1849 if (debug & DEBUG_HFCMULTI_DTMF) 1850 printk(KERN_DEBUG "%s: dtmf channel %d:", 1851 __func__, ch); 1852 coeff = &(hc->chan[ch].coeff[hc->chan[ch].coeff_count * 16]); 1853 dtmf = 1; 1854 for (co = 0; co < 8; co++) { 1855 /* read W(n-1) coefficient */ 1856 addr = hc->DTMFbase + ((co << 7) | (ch << 2)); 1857 HFC_outb_nodebug(hc, R_RAM_ADDR0, addr); 1858 HFC_outb_nodebug(hc, R_RAM_ADDR1, addr >> 8); 1859 HFC_outb_nodebug(hc, R_RAM_ADDR2, (addr >> 16) 1860 | V_ADDR_INC); 1861 w_float = HFC_inb_nodebug(hc, R_RAM_DATA); 1862 w_float |= (HFC_inb_nodebug(hc, R_RAM_DATA) << 8); 1863 if (debug & DEBUG_HFCMULTI_DTMF) 1864 printk(" %04x", w_float); 1865 1866 /* decode float (see chip doc) */ 1867 mantissa = w_float & 0x0fff; 1868 if (w_float & 0x8000) 1869 mantissa |= 0xfffff000; 1870 exponent = (w_float >> 12) & 0x7; 1871 if (exponent) { 1872 mantissa ^= 0x1000; 1873 mantissa <<= (exponent - 1); 1874 } 1875 1876 /* store coefficient */ 1877 coeff[co << 1] = mantissa; 1878 1879 /* read W(n) coefficient */ 1880 w_float = HFC_inb_nodebug(hc, R_RAM_DATA); 1881 w_float |= (HFC_inb_nodebug(hc, R_RAM_DATA) << 8); 1882 if (debug & DEBUG_HFCMULTI_DTMF) 1883 printk(" %04x", w_float); 1884 1885 /* decode float (see chip doc) */ 1886 mantissa = w_float & 0x0fff; 1887 if (w_float & 0x8000) 1888 mantissa |= 0xfffff000; 1889 exponent = (w_float >> 12) & 0x7; 1890 if (exponent) { 1891 mantissa ^= 0x1000; 1892 mantissa <<= (exponent - 1); 1893 } 1894 1895 /* store coefficient */ 1896 coeff[(co << 1) | 1] = mantissa; 1897 } 1898 if (debug & DEBUG_HFCMULTI_DTMF) 1899 printk(" DTMF ready %08x %08x %08x %08x " 1900 "%08x %08x %08x %08x\n", 1901 coeff[0], coeff[1], coeff[2], coeff[3], 1902 coeff[4], coeff[5], coeff[6], coeff[7]); 1903 hc->chan[ch].coeff_count++; 1904 if (hc->chan[ch].coeff_count == 8) { 1905 hc->chan[ch].coeff_count = 0; 1906 skb = mI_alloc_skb(512, GFP_ATOMIC); 1907 if (!skb) { 1908 printk(KERN_DEBUG "%s: No memory for skb\n", 1909 __func__); 1910 continue; 1911 } 1912 hh = mISDN_HEAD_P(skb); 1913 hh->prim = PH_CONTROL_IND; 1914 hh->id = DTMF_HFC_COEF; 1915 skb_put_data(skb, hc->chan[ch].coeff, 512); 1916 recv_Bchannel_skb(bch, skb); 1917 } 1918 } 1919 1920 /* restart DTMF processing */ 1921 hc->dtmf = dtmf; 1922 if (dtmf) 1923 HFC_outb_nodebug(hc, R_DTMF, hc->hw.r_dtmf | V_RST_DTMF); 1924 } 1925 1926 1927 /* 1928 * fill fifo as much as possible 1929 */ 1930 1931 static void 1932 hfcmulti_tx(struct hfc_multi *hc, int ch) 1933 { 1934 int i, ii, temp, len = 0; 1935 int Zspace, z1, z2; /* must be int for calculation */ 1936 int Fspace, f1, f2; 1937 u_char *d; 1938 int *txpending, slot_tx; 1939 struct bchannel *bch; 1940 struct dchannel *dch; 1941 struct sk_buff **sp = NULL; 1942 int *idxp; 1943 1944 bch = hc->chan[ch].bch; 1945 dch = hc->chan[ch].dch; 1946 if ((!dch) && (!bch)) 1947 return; 1948 1949 txpending = &hc->chan[ch].txpending; 1950 slot_tx = hc->chan[ch].slot_tx; 1951 if (dch) { 1952 if (!test_bit(FLG_ACTIVE, &dch->Flags)) 1953 return; 1954 sp = &dch->tx_skb; 1955 idxp = &dch->tx_idx; 1956 } else { 1957 if (!test_bit(FLG_ACTIVE, &bch->Flags)) 1958 return; 1959 sp = &bch->tx_skb; 1960 idxp = &bch->tx_idx; 1961 } 1962 if (*sp) 1963 len = (*sp)->len; 1964 1965 if ((!len) && *txpending != 1) 1966 return; /* no data */ 1967 1968 if (test_bit(HFC_CHIP_B410P, &hc->chip) && 1969 (hc->chan[ch].protocol == ISDN_P_B_RAW) && 1970 (hc->chan[ch].slot_rx < 0) && 1971 (hc->chan[ch].slot_tx < 0)) 1972 HFC_outb_nodebug(hc, R_FIFO, 0x20 | (ch << 1)); 1973 else 1974 HFC_outb_nodebug(hc, R_FIFO, ch << 1); 1975 HFC_wait_nodebug(hc); 1976 1977 if (*txpending == 2) { 1978 /* reset fifo */ 1979 HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_RES_F); 1980 HFC_wait_nodebug(hc); 1981 HFC_outb(hc, A_SUBCH_CFG, 0); 1982 *txpending = 1; 1983 } 1984 next_frame: 1985 if (dch || test_bit(FLG_HDLC, &bch->Flags)) { 1986 f1 = HFC_inb_nodebug(hc, A_F1); 1987 f2 = HFC_inb_nodebug(hc, A_F2); 1988 while (f2 != (temp = HFC_inb_nodebug(hc, A_F2))) { 1989 if (debug & DEBUG_HFCMULTI_FIFO) 1990 printk(KERN_DEBUG 1991 "%s(card %d): reread f2 because %d!=%d\n", 1992 __func__, hc->id + 1, temp, f2); 1993 f2 = temp; /* repeat until F2 is equal */ 1994 } 1995 Fspace = f2 - f1 - 1; 1996 if (Fspace < 0) 1997 Fspace += hc->Flen; 1998 /* 1999 * Old FIFO handling doesn't give us the current Z2 read 2000 * pointer, so we cannot send the next frame before the fifo 2001 * is empty. It makes no difference except for a slightly 2002 * lower performance. 2003 */ 2004 if (test_bit(HFC_CHIP_REVISION0, &hc->chip)) { 2005 if (f1 != f2) 2006 Fspace = 0; 2007 else 2008 Fspace = 1; 2009 } 2010 /* one frame only for ST D-channels, to allow resending */ 2011 if (hc->ctype != HFC_TYPE_E1 && dch) { 2012 if (f1 != f2) 2013 Fspace = 0; 2014 } 2015 /* F-counter full condition */ 2016 if (Fspace == 0) 2017 return; 2018 } 2019 z1 = HFC_inw_nodebug(hc, A_Z1) - hc->Zmin; 2020 z2 = HFC_inw_nodebug(hc, A_Z2) - hc->Zmin; 2021 while (z2 != (temp = (HFC_inw_nodebug(hc, A_Z2) - hc->Zmin))) { 2022 if (debug & DEBUG_HFCMULTI_FIFO) 2023 printk(KERN_DEBUG "%s(card %d): reread z2 because " 2024 "%d!=%d\n", __func__, hc->id + 1, temp, z2); 2025 z2 = temp; /* repeat unti Z2 is equal */ 2026 } 2027 hc->chan[ch].Zfill = z1 - z2; 2028 if (hc->chan[ch].Zfill < 0) 2029 hc->chan[ch].Zfill += hc->Zlen; 2030 Zspace = z2 - z1; 2031 if (Zspace <= 0) 2032 Zspace += hc->Zlen; 2033 Zspace -= 4; /* keep not too full, so pointers will not overrun */ 2034 /* fill transparent data only to maxinum transparent load (minus 4) */ 2035 if (bch && test_bit(FLG_TRANSPARENT, &bch->Flags)) 2036 Zspace = Zspace - hc->Zlen + hc->max_trans; 2037 if (Zspace <= 0) /* no space of 4 bytes */ 2038 return; 2039 2040 /* if no data */ 2041 if (!len) { 2042 if (z1 == z2) { /* empty */ 2043 /* if done with FIFO audio data during PCM connection */ 2044 if (bch && (!test_bit(FLG_HDLC, &bch->Flags)) && 2045 *txpending && slot_tx >= 0) { 2046 if (debug & DEBUG_HFCMULTI_MODE) 2047 printk(KERN_DEBUG 2048 "%s: reconnecting PCM due to no " 2049 "more FIFO data: channel %d " 2050 "slot_tx %d\n", 2051 __func__, ch, slot_tx); 2052 /* connect slot */ 2053 if (hc->ctype == HFC_TYPE_XHFC) 2054 HFC_outb(hc, A_CON_HDLC, 0xc0 2055 | 0x07 << 2 | V_HDLC_TRP | V_IFF); 2056 /* Enable FIFO, no interrupt */ 2057 else 2058 HFC_outb(hc, A_CON_HDLC, 0xc0 | 0x00 | 2059 V_HDLC_TRP | V_IFF); 2060 HFC_outb_nodebug(hc, R_FIFO, ch << 1 | 1); 2061 HFC_wait_nodebug(hc); 2062 if (hc->ctype == HFC_TYPE_XHFC) 2063 HFC_outb(hc, A_CON_HDLC, 0xc0 2064 | 0x07 << 2 | V_HDLC_TRP | V_IFF); 2065 /* Enable FIFO, no interrupt */ 2066 else 2067 HFC_outb(hc, A_CON_HDLC, 0xc0 | 0x00 | 2068 V_HDLC_TRP | V_IFF); 2069 HFC_outb_nodebug(hc, R_FIFO, ch << 1); 2070 HFC_wait_nodebug(hc); 2071 } 2072 *txpending = 0; 2073 } 2074 return; /* no data */ 2075 } 2076 2077 /* "fill fifo if empty" feature */ 2078 if (bch && test_bit(FLG_FILLEMPTY, &bch->Flags) 2079 && !test_bit(FLG_HDLC, &bch->Flags) && z2 == z1) { 2080 if (debug & DEBUG_HFCMULTI_FILL) 2081 printk(KERN_DEBUG "%s: buffer empty, so we have " 2082 "underrun\n", __func__); 2083 /* fill buffer, to prevent future underrun */ 2084 hc->write_fifo(hc, hc->silence_data, poll >> 1); 2085 Zspace -= (poll >> 1); 2086 } 2087 2088 /* if audio data and connected slot */ 2089 if (bch && (!test_bit(FLG_HDLC, &bch->Flags)) && (!*txpending) 2090 && slot_tx >= 0) { 2091 if (debug & DEBUG_HFCMULTI_MODE) 2092 printk(KERN_DEBUG "%s: disconnecting PCM due to " 2093 "FIFO data: channel %d slot_tx %d\n", 2094 __func__, ch, slot_tx); 2095 /* disconnect slot */ 2096 if (hc->ctype == HFC_TYPE_XHFC) 2097 HFC_outb(hc, A_CON_HDLC, 0x80 2098 | 0x07 << 2 | V_HDLC_TRP | V_IFF); 2099 /* Enable FIFO, no interrupt */ 2100 else 2101 HFC_outb(hc, A_CON_HDLC, 0x80 | 0x00 | 2102 V_HDLC_TRP | V_IFF); 2103 HFC_outb_nodebug(hc, R_FIFO, ch << 1 | 1); 2104 HFC_wait_nodebug(hc); 2105 if (hc->ctype == HFC_TYPE_XHFC) 2106 HFC_outb(hc, A_CON_HDLC, 0x80 2107 | 0x07 << 2 | V_HDLC_TRP | V_IFF); 2108 /* Enable FIFO, no interrupt */ 2109 else 2110 HFC_outb(hc, A_CON_HDLC, 0x80 | 0x00 | 2111 V_HDLC_TRP | V_IFF); 2112 HFC_outb_nodebug(hc, R_FIFO, ch << 1); 2113 HFC_wait_nodebug(hc); 2114 } 2115 *txpending = 1; 2116 2117 /* show activity */ 2118 if (dch) 2119 hc->activity_tx |= 1 << hc->chan[ch].port; 2120 2121 /* fill fifo to what we have left */ 2122 ii = len; 2123 if (dch || test_bit(FLG_HDLC, &bch->Flags)) 2124 temp = 1; 2125 else 2126 temp = 0; 2127 i = *idxp; 2128 d = (*sp)->data + i; 2129 if (ii - i > Zspace) 2130 ii = Zspace + i; 2131 if (debug & DEBUG_HFCMULTI_FIFO) 2132 printk(KERN_DEBUG "%s(card %d): fifo(%d) has %d bytes space " 2133 "left (z1=%04x, z2=%04x) sending %d of %d bytes %s\n", 2134 __func__, hc->id + 1, ch, Zspace, z1, z2, ii-i, len-i, 2135 temp ? "HDLC" : "TRANS"); 2136 2137 /* Have to prep the audio data */ 2138 hc->write_fifo(hc, d, ii - i); 2139 hc->chan[ch].Zfill += ii - i; 2140 *idxp = ii; 2141 2142 /* if not all data has been written */ 2143 if (ii != len) { 2144 /* NOTE: fifo is started by the calling function */ 2145 return; 2146 } 2147 2148 /* if all data has been written, terminate frame */ 2149 if (dch || test_bit(FLG_HDLC, &bch->Flags)) { 2150 /* increment f-counter */ 2151 HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_INC_F); 2152 HFC_wait_nodebug(hc); 2153 } 2154 2155 dev_kfree_skb(*sp); 2156 /* check for next frame */ 2157 if (bch && get_next_bframe(bch)) { 2158 len = (*sp)->len; 2159 goto next_frame; 2160 } 2161 if (dch && get_next_dframe(dch)) { 2162 len = (*sp)->len; 2163 goto next_frame; 2164 } 2165 2166 /* 2167 * now we have no more data, so in case of transparent, 2168 * we set the last byte in fifo to 'silence' in case we will get 2169 * no more data at all. this prevents sending an undefined value. 2170 */ 2171 if (bch && test_bit(FLG_TRANSPARENT, &bch->Flags)) 2172 HFC_outb_nodebug(hc, A_FIFO_DATA0_NOINC, hc->silence); 2173 } 2174 2175 2176 /* NOTE: only called if E1 card is in active state */ 2177 static void 2178 hfcmulti_rx(struct hfc_multi *hc, int ch) 2179 { 2180 int temp; 2181 int Zsize, z1, z2 = 0; /* = 0, to make GCC happy */ 2182 int f1 = 0, f2 = 0; /* = 0, to make GCC happy */ 2183 int again = 0; 2184 struct bchannel *bch; 2185 struct dchannel *dch = NULL; 2186 struct sk_buff *skb, **sp = NULL; 2187 int maxlen; 2188 2189 bch = hc->chan[ch].bch; 2190 if (bch) { 2191 if (!test_bit(FLG_ACTIVE, &bch->Flags)) 2192 return; 2193 } else if (hc->chan[ch].dch) { 2194 dch = hc->chan[ch].dch; 2195 if (!test_bit(FLG_ACTIVE, &dch->Flags)) 2196 return; 2197 } else { 2198 return; 2199 } 2200 next_frame: 2201 /* on first AND before getting next valid frame, R_FIFO must be written 2202 to. */ 2203 if (test_bit(HFC_CHIP_B410P, &hc->chip) && 2204 (hc->chan[ch].protocol == ISDN_P_B_RAW) && 2205 (hc->chan[ch].slot_rx < 0) && 2206 (hc->chan[ch].slot_tx < 0)) 2207 HFC_outb_nodebug(hc, R_FIFO, 0x20 | (ch << 1) | 1); 2208 else 2209 HFC_outb_nodebug(hc, R_FIFO, (ch << 1) | 1); 2210 HFC_wait_nodebug(hc); 2211 2212 /* ignore if rx is off BUT change fifo (above) to start pending TX */ 2213 if (hc->chan[ch].rx_off) { 2214 if (bch) 2215 bch->dropcnt += poll; /* not exact but fair enough */ 2216 return; 2217 } 2218 2219 if (dch || test_bit(FLG_HDLC, &bch->Flags)) { 2220 f1 = HFC_inb_nodebug(hc, A_F1); 2221 while (f1 != (temp = HFC_inb_nodebug(hc, A_F1))) { 2222 if (debug & DEBUG_HFCMULTI_FIFO) 2223 printk(KERN_DEBUG 2224 "%s(card %d): reread f1 because %d!=%d\n", 2225 __func__, hc->id + 1, temp, f1); 2226 f1 = temp; /* repeat until F1 is equal */ 2227 } 2228 f2 = HFC_inb_nodebug(hc, A_F2); 2229 } 2230 z1 = HFC_inw_nodebug(hc, A_Z1) - hc->Zmin; 2231 while (z1 != (temp = (HFC_inw_nodebug(hc, A_Z1) - hc->Zmin))) { 2232 if (debug & DEBUG_HFCMULTI_FIFO) 2233 printk(KERN_DEBUG "%s(card %d): reread z2 because " 2234 "%d!=%d\n", __func__, hc->id + 1, temp, z2); 2235 z1 = temp; /* repeat until Z1 is equal */ 2236 } 2237 z2 = HFC_inw_nodebug(hc, A_Z2) - hc->Zmin; 2238 Zsize = z1 - z2; 2239 if ((dch || test_bit(FLG_HDLC, &bch->Flags)) && f1 != f2) 2240 /* complete hdlc frame */ 2241 Zsize++; 2242 if (Zsize < 0) 2243 Zsize += hc->Zlen; 2244 /* if buffer is empty */ 2245 if (Zsize <= 0) 2246 return; 2247 2248 if (bch) { 2249 maxlen = bchannel_get_rxbuf(bch, Zsize); 2250 if (maxlen < 0) { 2251 pr_warning("card%d.B%d: No bufferspace for %d bytes\n", 2252 hc->id + 1, bch->nr, Zsize); 2253 return; 2254 } 2255 sp = &bch->rx_skb; 2256 maxlen = bch->maxlen; 2257 } else { /* Dchannel */ 2258 sp = &dch->rx_skb; 2259 maxlen = dch->maxlen + 3; 2260 if (*sp == NULL) { 2261 *sp = mI_alloc_skb(maxlen, GFP_ATOMIC); 2262 if (*sp == NULL) { 2263 pr_warning("card%d: No mem for dch rx_skb\n", 2264 hc->id + 1); 2265 return; 2266 } 2267 } 2268 } 2269 /* show activity */ 2270 if (dch) 2271 hc->activity_rx |= 1 << hc->chan[ch].port; 2272 2273 /* empty fifo with what we have */ 2274 if (dch || test_bit(FLG_HDLC, &bch->Flags)) { 2275 if (debug & DEBUG_HFCMULTI_FIFO) 2276 printk(KERN_DEBUG "%s(card %d): fifo(%d) reading %d " 2277 "bytes (z1=%04x, z2=%04x) HDLC %s (f1=%d, f2=%d) " 2278 "got=%d (again %d)\n", __func__, hc->id + 1, ch, 2279 Zsize, z1, z2, (f1 == f2) ? "fragment" : "COMPLETE", 2280 f1, f2, Zsize + (*sp)->len, again); 2281 /* HDLC */ 2282 if ((Zsize + (*sp)->len) > maxlen) { 2283 if (debug & DEBUG_HFCMULTI_FIFO) 2284 printk(KERN_DEBUG 2285 "%s(card %d): hdlc-frame too large.\n", 2286 __func__, hc->id + 1); 2287 skb_trim(*sp, 0); 2288 HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_RES_F); 2289 HFC_wait_nodebug(hc); 2290 return; 2291 } 2292 2293 hc->read_fifo(hc, skb_put(*sp, Zsize), Zsize); 2294 2295 if (f1 != f2) { 2296 /* increment Z2,F2-counter */ 2297 HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_INC_F); 2298 HFC_wait_nodebug(hc); 2299 /* check size */ 2300 if ((*sp)->len < 4) { 2301 if (debug & DEBUG_HFCMULTI_FIFO) 2302 printk(KERN_DEBUG 2303 "%s(card %d): Frame below minimum " 2304 "size\n", __func__, hc->id + 1); 2305 skb_trim(*sp, 0); 2306 goto next_frame; 2307 } 2308 /* there is at least one complete frame, check crc */ 2309 if ((*sp)->data[(*sp)->len - 1]) { 2310 if (debug & DEBUG_HFCMULTI_CRC) 2311 printk(KERN_DEBUG 2312 "%s: CRC-error\n", __func__); 2313 skb_trim(*sp, 0); 2314 goto next_frame; 2315 } 2316 skb_trim(*sp, (*sp)->len - 3); 2317 if ((*sp)->len < MISDN_COPY_SIZE) { 2318 skb = *sp; 2319 *sp = mI_alloc_skb(skb->len, GFP_ATOMIC); 2320 if (*sp) { 2321 skb_put_data(*sp, skb->data, skb->len); 2322 skb_trim(skb, 0); 2323 } else { 2324 printk(KERN_DEBUG "%s: No mem\n", 2325 __func__); 2326 *sp = skb; 2327 skb = NULL; 2328 } 2329 } else { 2330 skb = NULL; 2331 } 2332 if (debug & DEBUG_HFCMULTI_FIFO) { 2333 printk(KERN_DEBUG "%s(card %d):", 2334 __func__, hc->id + 1); 2335 temp = 0; 2336 while (temp < (*sp)->len) 2337 printk(" %02x", (*sp)->data[temp++]); 2338 printk("\n"); 2339 } 2340 if (dch) 2341 recv_Dchannel(dch); 2342 else 2343 recv_Bchannel(bch, MISDN_ID_ANY, false); 2344 *sp = skb; 2345 again++; 2346 goto next_frame; 2347 } 2348 /* there is an incomplete frame */ 2349 } else { 2350 /* transparent */ 2351 hc->read_fifo(hc, skb_put(*sp, Zsize), Zsize); 2352 if (debug & DEBUG_HFCMULTI_FIFO) 2353 printk(KERN_DEBUG 2354 "%s(card %d): fifo(%d) reading %d bytes " 2355 "(z1=%04x, z2=%04x) TRANS\n", 2356 __func__, hc->id + 1, ch, Zsize, z1, z2); 2357 /* only bch is transparent */ 2358 recv_Bchannel(bch, hc->chan[ch].Zfill, false); 2359 } 2360 } 2361 2362 2363 /* 2364 * Interrupt handler 2365 */ 2366 static void 2367 signal_state_up(struct dchannel *dch, int info, char *msg) 2368 { 2369 struct sk_buff *skb; 2370 int id, data = info; 2371 2372 if (debug & DEBUG_HFCMULTI_STATE) 2373 printk(KERN_DEBUG "%s: %s\n", __func__, msg); 2374 2375 id = TEI_SAPI | (GROUP_TEI << 8); /* manager address */ 2376 2377 skb = _alloc_mISDN_skb(MPH_INFORMATION_IND, id, sizeof(data), &data, 2378 GFP_ATOMIC); 2379 if (!skb) 2380 return; 2381 recv_Dchannel_skb(dch, skb); 2382 } 2383 2384 static inline void 2385 handle_timer_irq(struct hfc_multi *hc) 2386 { 2387 int ch, temp; 2388 struct dchannel *dch; 2389 u_long flags; 2390 2391 /* process queued resync jobs */ 2392 if (hc->e1_resync) { 2393 /* lock, so e1_resync gets not changed */ 2394 spin_lock_irqsave(&HFClock, flags); 2395 if (hc->e1_resync & 1) { 2396 if (debug & DEBUG_HFCMULTI_PLXSD) 2397 printk(KERN_DEBUG "Enable SYNC_I\n"); 2398 HFC_outb(hc, R_SYNC_CTRL, V_EXT_CLK_SYNC); 2399 /* disable JATT, if RX_SYNC is set */ 2400 if (test_bit(HFC_CHIP_RX_SYNC, &hc->chip)) 2401 HFC_outb(hc, R_SYNC_OUT, V_SYNC_E1_RX); 2402 } 2403 if (hc->e1_resync & 2) { 2404 if (debug & DEBUG_HFCMULTI_PLXSD) 2405 printk(KERN_DEBUG "Enable jatt PLL\n"); 2406 HFC_outb(hc, R_SYNC_CTRL, V_SYNC_OFFS); 2407 } 2408 if (hc->e1_resync & 4) { 2409 if (debug & DEBUG_HFCMULTI_PLXSD) 2410 printk(KERN_DEBUG 2411 "Enable QUARTZ for HFC-E1\n"); 2412 /* set jatt to quartz */ 2413 HFC_outb(hc, R_SYNC_CTRL, V_EXT_CLK_SYNC 2414 | V_JATT_OFF); 2415 /* switch to JATT, in case it is not already */ 2416 HFC_outb(hc, R_SYNC_OUT, 0); 2417 } 2418 hc->e1_resync = 0; 2419 spin_unlock_irqrestore(&HFClock, flags); 2420 } 2421 2422 if (hc->ctype != HFC_TYPE_E1 || hc->e1_state == 1) 2423 for (ch = 0; ch <= 31; ch++) { 2424 if (hc->created[hc->chan[ch].port]) { 2425 hfcmulti_tx(hc, ch); 2426 /* fifo is started when switching to rx-fifo */ 2427 hfcmulti_rx(hc, ch); 2428 if (hc->chan[ch].dch && 2429 hc->chan[ch].nt_timer > -1) { 2430 dch = hc->chan[ch].dch; 2431 if (!(--hc->chan[ch].nt_timer)) { 2432 schedule_event(dch, 2433 FLG_PHCHANGE); 2434 if (debug & 2435 DEBUG_HFCMULTI_STATE) 2436 printk(KERN_DEBUG 2437 "%s: nt_timer at " 2438 "state %x\n", 2439 __func__, 2440 dch->state); 2441 } 2442 } 2443 } 2444 } 2445 if (hc->ctype == HFC_TYPE_E1 && hc->created[0]) { 2446 dch = hc->chan[hc->dnum[0]].dch; 2447 /* LOS */ 2448 temp = HFC_inb_nodebug(hc, R_SYNC_STA) & V_SIG_LOS; 2449 hc->chan[hc->dnum[0]].los = temp; 2450 if (test_bit(HFC_CFG_REPORT_LOS, &hc->chan[hc->dnum[0]].cfg)) { 2451 if (!temp && hc->chan[hc->dnum[0]].los) 2452 signal_state_up(dch, L1_SIGNAL_LOS_ON, 2453 "LOS detected"); 2454 if (temp && !hc->chan[hc->dnum[0]].los) 2455 signal_state_up(dch, L1_SIGNAL_LOS_OFF, 2456 "LOS gone"); 2457 } 2458 if (test_bit(HFC_CFG_REPORT_AIS, &hc->chan[hc->dnum[0]].cfg)) { 2459 /* AIS */ 2460 temp = HFC_inb_nodebug(hc, R_SYNC_STA) & V_AIS; 2461 if (!temp && hc->chan[hc->dnum[0]].ais) 2462 signal_state_up(dch, L1_SIGNAL_AIS_ON, 2463 "AIS detected"); 2464 if (temp && !hc->chan[hc->dnum[0]].ais) 2465 signal_state_up(dch, L1_SIGNAL_AIS_OFF, 2466 "AIS gone"); 2467 hc->chan[hc->dnum[0]].ais = temp; 2468 } 2469 if (test_bit(HFC_CFG_REPORT_SLIP, &hc->chan[hc->dnum[0]].cfg)) { 2470 /* SLIP */ 2471 temp = HFC_inb_nodebug(hc, R_SLIP) & V_FOSLIP_RX; 2472 if (!temp && hc->chan[hc->dnum[0]].slip_rx) 2473 signal_state_up(dch, L1_SIGNAL_SLIP_RX, 2474 " bit SLIP detected RX"); 2475 hc->chan[hc->dnum[0]].slip_rx = temp; 2476 temp = HFC_inb_nodebug(hc, R_SLIP) & V_FOSLIP_TX; 2477 if (!temp && hc->chan[hc->dnum[0]].slip_tx) 2478 signal_state_up(dch, L1_SIGNAL_SLIP_TX, 2479 " bit SLIP detected TX"); 2480 hc->chan[hc->dnum[0]].slip_tx = temp; 2481 } 2482 if (test_bit(HFC_CFG_REPORT_RDI, &hc->chan[hc->dnum[0]].cfg)) { 2483 /* RDI */ 2484 temp = HFC_inb_nodebug(hc, R_RX_SL0_0) & V_A; 2485 if (!temp && hc->chan[hc->dnum[0]].rdi) 2486 signal_state_up(dch, L1_SIGNAL_RDI_ON, 2487 "RDI detected"); 2488 if (temp && !hc->chan[hc->dnum[0]].rdi) 2489 signal_state_up(dch, L1_SIGNAL_RDI_OFF, 2490 "RDI gone"); 2491 hc->chan[hc->dnum[0]].rdi = temp; 2492 } 2493 temp = HFC_inb_nodebug(hc, R_JATT_DIR); 2494 switch (hc->chan[hc->dnum[0]].sync) { 2495 case 0: 2496 if ((temp & 0x60) == 0x60) { 2497 if (debug & DEBUG_HFCMULTI_SYNC) 2498 printk(KERN_DEBUG 2499 "%s: (id=%d) E1 now " 2500 "in clock sync\n", 2501 __func__, hc->id); 2502 HFC_outb(hc, R_RX_OFF, 2503 hc->chan[hc->dnum[0]].jitter | V_RX_INIT); 2504 HFC_outb(hc, R_TX_OFF, 2505 hc->chan[hc->dnum[0]].jitter | V_RX_INIT); 2506 hc->chan[hc->dnum[0]].sync = 1; 2507 goto check_framesync; 2508 } 2509 break; 2510 case 1: 2511 if ((temp & 0x60) != 0x60) { 2512 if (debug & DEBUG_HFCMULTI_SYNC) 2513 printk(KERN_DEBUG 2514 "%s: (id=%d) E1 " 2515 "lost clock sync\n", 2516 __func__, hc->id); 2517 hc->chan[hc->dnum[0]].sync = 0; 2518 break; 2519 } 2520 check_framesync: 2521 temp = HFC_inb_nodebug(hc, R_SYNC_STA); 2522 if (temp == 0x27) { 2523 if (debug & DEBUG_HFCMULTI_SYNC) 2524 printk(KERN_DEBUG 2525 "%s: (id=%d) E1 " 2526 "now in frame sync\n", 2527 __func__, hc->id); 2528 hc->chan[hc->dnum[0]].sync = 2; 2529 } 2530 break; 2531 case 2: 2532 if ((temp & 0x60) != 0x60) { 2533 if (debug & DEBUG_HFCMULTI_SYNC) 2534 printk(KERN_DEBUG 2535 "%s: (id=%d) E1 lost " 2536 "clock & frame sync\n", 2537 __func__, hc->id); 2538 hc->chan[hc->dnum[0]].sync = 0; 2539 break; 2540 } 2541 temp = HFC_inb_nodebug(hc, R_SYNC_STA); 2542 if (temp != 0x27) { 2543 if (debug & DEBUG_HFCMULTI_SYNC) 2544 printk(KERN_DEBUG 2545 "%s: (id=%d) E1 " 2546 "lost frame sync\n", 2547 __func__, hc->id); 2548 hc->chan[hc->dnum[0]].sync = 1; 2549 } 2550 break; 2551 } 2552 } 2553 2554 if (test_bit(HFC_CHIP_WATCHDOG, &hc->chip)) 2555 hfcmulti_watchdog(hc); 2556 2557 if (hc->leds) 2558 hfcmulti_leds(hc); 2559 } 2560 2561 static void 2562 ph_state_irq(struct hfc_multi *hc, u_char r_irq_statech) 2563 { 2564 struct dchannel *dch; 2565 int ch; 2566 int active; 2567 u_char st_status, temp; 2568 2569 /* state machine */ 2570 for (ch = 0; ch <= 31; ch++) { 2571 if (hc->chan[ch].dch) { 2572 dch = hc->chan[ch].dch; 2573 if (r_irq_statech & 1) { 2574 HFC_outb_nodebug(hc, R_ST_SEL, 2575 hc->chan[ch].port); 2576 /* undocumented: delay after R_ST_SEL */ 2577 udelay(1); 2578 /* undocumented: status changes during read */ 2579 st_status = HFC_inb_nodebug(hc, A_ST_RD_STATE); 2580 while (st_status != (temp = 2581 HFC_inb_nodebug(hc, A_ST_RD_STATE))) { 2582 if (debug & DEBUG_HFCMULTI_STATE) 2583 printk(KERN_DEBUG "%s: reread " 2584 "STATE because %d!=%d\n", 2585 __func__, temp, 2586 st_status); 2587 st_status = temp; /* repeat */ 2588 } 2589 2590 /* Speech Design TE-sync indication */ 2591 if (test_bit(HFC_CHIP_PLXSD, &hc->chip) && 2592 dch->dev.D.protocol == ISDN_P_TE_S0) { 2593 if (st_status & V_FR_SYNC_ST) 2594 hc->syncronized |= 2595 (1 << hc->chan[ch].port); 2596 else 2597 hc->syncronized &= 2598 ~(1 << hc->chan[ch].port); 2599 } 2600 dch->state = st_status & 0x0f; 2601 if (dch->dev.D.protocol == ISDN_P_NT_S0) 2602 active = 3; 2603 else 2604 active = 7; 2605 if (dch->state == active) { 2606 HFC_outb_nodebug(hc, R_FIFO, 2607 (ch << 1) | 1); 2608 HFC_wait_nodebug(hc); 2609 HFC_outb_nodebug(hc, 2610 R_INC_RES_FIFO, V_RES_F); 2611 HFC_wait_nodebug(hc); 2612 dch->tx_idx = 0; 2613 } 2614 schedule_event(dch, FLG_PHCHANGE); 2615 if (debug & DEBUG_HFCMULTI_STATE) 2616 printk(KERN_DEBUG 2617 "%s: S/T newstate %x port %d\n", 2618 __func__, dch->state, 2619 hc->chan[ch].port); 2620 } 2621 r_irq_statech >>= 1; 2622 } 2623 } 2624 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) 2625 plxsd_checksync(hc, 0); 2626 } 2627 2628 static void 2629 fifo_irq(struct hfc_multi *hc, int block) 2630 { 2631 int ch, j; 2632 struct dchannel *dch; 2633 struct bchannel *bch; 2634 u_char r_irq_fifo_bl; 2635 2636 r_irq_fifo_bl = HFC_inb_nodebug(hc, R_IRQ_FIFO_BL0 + block); 2637 j = 0; 2638 while (j < 8) { 2639 ch = (block << 2) + (j >> 1); 2640 dch = hc->chan[ch].dch; 2641 bch = hc->chan[ch].bch; 2642 if (((!dch) && (!bch)) || (!hc->created[hc->chan[ch].port])) { 2643 j += 2; 2644 continue; 2645 } 2646 if (dch && (r_irq_fifo_bl & (1 << j)) && 2647 test_bit(FLG_ACTIVE, &dch->Flags)) { 2648 hfcmulti_tx(hc, ch); 2649 /* start fifo */ 2650 HFC_outb_nodebug(hc, R_FIFO, 0); 2651 HFC_wait_nodebug(hc); 2652 } 2653 if (bch && (r_irq_fifo_bl & (1 << j)) && 2654 test_bit(FLG_ACTIVE, &bch->Flags)) { 2655 hfcmulti_tx(hc, ch); 2656 /* start fifo */ 2657 HFC_outb_nodebug(hc, R_FIFO, 0); 2658 HFC_wait_nodebug(hc); 2659 } 2660 j++; 2661 if (dch && (r_irq_fifo_bl & (1 << j)) && 2662 test_bit(FLG_ACTIVE, &dch->Flags)) { 2663 hfcmulti_rx(hc, ch); 2664 } 2665 if (bch && (r_irq_fifo_bl & (1 << j)) && 2666 test_bit(FLG_ACTIVE, &bch->Flags)) { 2667 hfcmulti_rx(hc, ch); 2668 } 2669 j++; 2670 } 2671 } 2672 2673 #ifdef IRQ_DEBUG 2674 int irqsem; 2675 #endif 2676 static irqreturn_t 2677 hfcmulti_interrupt(int intno, void *dev_id) 2678 { 2679 #ifdef IRQCOUNT_DEBUG 2680 static int iq1 = 0, iq2 = 0, iq3 = 0, iq4 = 0, 2681 iq5 = 0, iq6 = 0, iqcnt = 0; 2682 #endif 2683 struct hfc_multi *hc = dev_id; 2684 struct dchannel *dch; 2685 u_char r_irq_statech, status, r_irq_misc, r_irq_oview; 2686 int i; 2687 void __iomem *plx_acc; 2688 u_short wval; 2689 u_char e1_syncsta, temp, temp2; 2690 u_long flags; 2691 2692 if (!hc) { 2693 printk(KERN_ERR "HFC-multi: Spurious interrupt!\n"); 2694 return IRQ_NONE; 2695 } 2696 2697 spin_lock(&hc->lock); 2698 2699 #ifdef IRQ_DEBUG 2700 if (irqsem) 2701 printk(KERN_ERR "irq for card %d during irq from " 2702 "card %d, this is no bug.\n", hc->id + 1, irqsem); 2703 irqsem = hc->id + 1; 2704 #endif 2705 #ifdef CONFIG_MISDN_HFCMULTI_8xx 2706 if (hc->immap->im_cpm.cp_pbdat & hc->pb_irqmsk) 2707 goto irq_notforus; 2708 #endif 2709 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 2710 spin_lock_irqsave(&plx_lock, flags); 2711 plx_acc = hc->plx_membase + PLX_INTCSR; 2712 wval = readw(plx_acc); 2713 spin_unlock_irqrestore(&plx_lock, flags); 2714 if (!(wval & PLX_INTCSR_LINTI1_STATUS)) 2715 goto irq_notforus; 2716 } 2717 2718 status = HFC_inb_nodebug(hc, R_STATUS); 2719 r_irq_statech = HFC_inb_nodebug(hc, R_IRQ_STATECH); 2720 #ifdef IRQCOUNT_DEBUG 2721 if (r_irq_statech) 2722 iq1++; 2723 if (status & V_DTMF_STA) 2724 iq2++; 2725 if (status & V_LOST_STA) 2726 iq3++; 2727 if (status & V_EXT_IRQSTA) 2728 iq4++; 2729 if (status & V_MISC_IRQSTA) 2730 iq5++; 2731 if (status & V_FR_IRQSTA) 2732 iq6++; 2733 if (iqcnt++ > 5000) { 2734 printk(KERN_ERR "iq1:%x iq2:%x iq3:%x iq4:%x iq5:%x iq6:%x\n", 2735 iq1, iq2, iq3, iq4, iq5, iq6); 2736 iqcnt = 0; 2737 } 2738 #endif 2739 2740 if (!r_irq_statech && 2741 !(status & (V_DTMF_STA | V_LOST_STA | V_EXT_IRQSTA | 2742 V_MISC_IRQSTA | V_FR_IRQSTA))) { 2743 /* irq is not for us */ 2744 goto irq_notforus; 2745 } 2746 hc->irqcnt++; 2747 if (r_irq_statech) { 2748 if (hc->ctype != HFC_TYPE_E1) 2749 ph_state_irq(hc, r_irq_statech); 2750 } 2751 if (status & V_EXT_IRQSTA) 2752 ; /* external IRQ */ 2753 if (status & V_LOST_STA) { 2754 /* LOST IRQ */ 2755 HFC_outb(hc, R_INC_RES_FIFO, V_RES_LOST); /* clear irq! */ 2756 } 2757 if (status & V_MISC_IRQSTA) { 2758 /* misc IRQ */ 2759 r_irq_misc = HFC_inb_nodebug(hc, R_IRQ_MISC); 2760 r_irq_misc &= hc->hw.r_irqmsk_misc; /* ignore disabled irqs */ 2761 if (r_irq_misc & V_STA_IRQ) { 2762 if (hc->ctype == HFC_TYPE_E1) { 2763 /* state machine */ 2764 dch = hc->chan[hc->dnum[0]].dch; 2765 e1_syncsta = HFC_inb_nodebug(hc, R_SYNC_STA); 2766 if (test_bit(HFC_CHIP_PLXSD, &hc->chip) 2767 && hc->e1_getclock) { 2768 if (e1_syncsta & V_FR_SYNC_E1) 2769 hc->syncronized = 1; 2770 else 2771 hc->syncronized = 0; 2772 } 2773 /* undocumented: status changes during read */ 2774 temp = HFC_inb_nodebug(hc, R_E1_RD_STA); 2775 while (temp != (temp2 = 2776 HFC_inb_nodebug(hc, R_E1_RD_STA))) { 2777 if (debug & DEBUG_HFCMULTI_STATE) 2778 printk(KERN_DEBUG "%s: reread " 2779 "STATE because %d!=%d\n", 2780 __func__, temp, temp2); 2781 temp = temp2; /* repeat */ 2782 } 2783 /* broadcast state change to all fragments */ 2784 if (debug & DEBUG_HFCMULTI_STATE) 2785 printk(KERN_DEBUG 2786 "%s: E1 (id=%d) newstate %x\n", 2787 __func__, hc->id, temp & 0x7); 2788 for (i = 0; i < hc->ports; i++) { 2789 dch = hc->chan[hc->dnum[i]].dch; 2790 dch->state = temp & 0x7; 2791 schedule_event(dch, FLG_PHCHANGE); 2792 } 2793 2794 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) 2795 plxsd_checksync(hc, 0); 2796 } 2797 } 2798 if (r_irq_misc & V_TI_IRQ) { 2799 if (hc->iclock_on) 2800 mISDN_clock_update(hc->iclock, poll, NULL); 2801 handle_timer_irq(hc); 2802 } 2803 2804 if (r_irq_misc & V_DTMF_IRQ) 2805 hfcmulti_dtmf(hc); 2806 2807 if (r_irq_misc & V_IRQ_PROC) { 2808 static int irq_proc_cnt; 2809 if (!irq_proc_cnt++) 2810 printk(KERN_DEBUG "%s: got V_IRQ_PROC -" 2811 " this should not happen\n", __func__); 2812 } 2813 2814 } 2815 if (status & V_FR_IRQSTA) { 2816 /* FIFO IRQ */ 2817 r_irq_oview = HFC_inb_nodebug(hc, R_IRQ_OVIEW); 2818 for (i = 0; i < 8; i++) { 2819 if (r_irq_oview & (1 << i)) 2820 fifo_irq(hc, i); 2821 } 2822 } 2823 2824 #ifdef IRQ_DEBUG 2825 irqsem = 0; 2826 #endif 2827 spin_unlock(&hc->lock); 2828 return IRQ_HANDLED; 2829 2830 irq_notforus: 2831 #ifdef IRQ_DEBUG 2832 irqsem = 0; 2833 #endif 2834 spin_unlock(&hc->lock); 2835 return IRQ_NONE; 2836 } 2837 2838 2839 /* 2840 * timer callback for D-chan busy resolution. Currently no function 2841 */ 2842 2843 static void 2844 hfcmulti_dbusy_timer(struct timer_list *t) 2845 { 2846 } 2847 2848 2849 /* 2850 * activate/deactivate hardware for selected channels and mode 2851 * 2852 * configure B-channel with the given protocol 2853 * ch eqals to the HFC-channel (0-31) 2854 * ch is the number of channel (0-4,4-7,8-11,12-15,16-19,20-23,24-27,28-31 2855 * for S/T, 1-31 for E1) 2856 * the hdlc interrupts will be set/unset 2857 */ 2858 static int 2859 mode_hfcmulti(struct hfc_multi *hc, int ch, int protocol, int slot_tx, 2860 int bank_tx, int slot_rx, int bank_rx) 2861 { 2862 int flow_tx = 0, flow_rx = 0, routing = 0; 2863 int oslot_tx, oslot_rx; 2864 int conf; 2865 2866 if (ch < 0 || ch > 31) 2867 return -EINVAL; 2868 oslot_tx = hc->chan[ch].slot_tx; 2869 oslot_rx = hc->chan[ch].slot_rx; 2870 conf = hc->chan[ch].conf; 2871 2872 if (debug & DEBUG_HFCMULTI_MODE) 2873 printk(KERN_DEBUG 2874 "%s: card %d channel %d protocol %x slot old=%d new=%d " 2875 "bank new=%d (TX) slot old=%d new=%d bank new=%d (RX)\n", 2876 __func__, hc->id, ch, protocol, oslot_tx, slot_tx, 2877 bank_tx, oslot_rx, slot_rx, bank_rx); 2878 2879 if (oslot_tx >= 0 && slot_tx != oslot_tx) { 2880 /* remove from slot */ 2881 if (debug & DEBUG_HFCMULTI_MODE) 2882 printk(KERN_DEBUG "%s: remove from slot %d (TX)\n", 2883 __func__, oslot_tx); 2884 if (hc->slot_owner[oslot_tx << 1] == ch) { 2885 HFC_outb(hc, R_SLOT, oslot_tx << 1); 2886 HFC_outb(hc, A_SL_CFG, 0); 2887 if (hc->ctype != HFC_TYPE_XHFC) 2888 HFC_outb(hc, A_CONF, 0); 2889 hc->slot_owner[oslot_tx << 1] = -1; 2890 } else { 2891 if (debug & DEBUG_HFCMULTI_MODE) 2892 printk(KERN_DEBUG 2893 "%s: we are not owner of this tx slot " 2894 "anymore, channel %d is.\n", 2895 __func__, hc->slot_owner[oslot_tx << 1]); 2896 } 2897 } 2898 2899 if (oslot_rx >= 0 && slot_rx != oslot_rx) { 2900 /* remove from slot */ 2901 if (debug & DEBUG_HFCMULTI_MODE) 2902 printk(KERN_DEBUG 2903 "%s: remove from slot %d (RX)\n", 2904 __func__, oslot_rx); 2905 if (hc->slot_owner[(oslot_rx << 1) | 1] == ch) { 2906 HFC_outb(hc, R_SLOT, (oslot_rx << 1) | V_SL_DIR); 2907 HFC_outb(hc, A_SL_CFG, 0); 2908 hc->slot_owner[(oslot_rx << 1) | 1] = -1; 2909 } else { 2910 if (debug & DEBUG_HFCMULTI_MODE) 2911 printk(KERN_DEBUG 2912 "%s: we are not owner of this rx slot " 2913 "anymore, channel %d is.\n", 2914 __func__, 2915 hc->slot_owner[(oslot_rx << 1) | 1]); 2916 } 2917 } 2918 2919 if (slot_tx < 0) { 2920 flow_tx = 0x80; /* FIFO->ST */ 2921 /* disable pcm slot */ 2922 hc->chan[ch].slot_tx = -1; 2923 hc->chan[ch].bank_tx = 0; 2924 } else { 2925 /* set pcm slot */ 2926 if (hc->chan[ch].txpending) 2927 flow_tx = 0x80; /* FIFO->ST */ 2928 else 2929 flow_tx = 0xc0; /* PCM->ST */ 2930 /* put on slot */ 2931 routing = bank_tx ? 0xc0 : 0x80; 2932 if (conf >= 0 || bank_tx > 1) 2933 routing = 0x40; /* loop */ 2934 if (debug & DEBUG_HFCMULTI_MODE) 2935 printk(KERN_DEBUG "%s: put channel %d to slot %d bank" 2936 " %d flow %02x routing %02x conf %d (TX)\n", 2937 __func__, ch, slot_tx, bank_tx, 2938 flow_tx, routing, conf); 2939 HFC_outb(hc, R_SLOT, slot_tx << 1); 2940 HFC_outb(hc, A_SL_CFG, (ch << 1) | routing); 2941 if (hc->ctype != HFC_TYPE_XHFC) 2942 HFC_outb(hc, A_CONF, 2943 (conf < 0) ? 0 : (conf | V_CONF_SL)); 2944 hc->slot_owner[slot_tx << 1] = ch; 2945 hc->chan[ch].slot_tx = slot_tx; 2946 hc->chan[ch].bank_tx = bank_tx; 2947 } 2948 if (slot_rx < 0) { 2949 /* disable pcm slot */ 2950 flow_rx = 0x80; /* ST->FIFO */ 2951 hc->chan[ch].slot_rx = -1; 2952 hc->chan[ch].bank_rx = 0; 2953 } else { 2954 /* set pcm slot */ 2955 if (hc->chan[ch].txpending) 2956 flow_rx = 0x80; /* ST->FIFO */ 2957 else 2958 flow_rx = 0xc0; /* ST->(FIFO,PCM) */ 2959 /* put on slot */ 2960 routing = bank_rx ? 0x80 : 0xc0; /* reversed */ 2961 if (conf >= 0 || bank_rx > 1) 2962 routing = 0x40; /* loop */ 2963 if (debug & DEBUG_HFCMULTI_MODE) 2964 printk(KERN_DEBUG "%s: put channel %d to slot %d bank" 2965 " %d flow %02x routing %02x conf %d (RX)\n", 2966 __func__, ch, slot_rx, bank_rx, 2967 flow_rx, routing, conf); 2968 HFC_outb(hc, R_SLOT, (slot_rx << 1) | V_SL_DIR); 2969 HFC_outb(hc, A_SL_CFG, (ch << 1) | V_CH_DIR | routing); 2970 hc->slot_owner[(slot_rx << 1) | 1] = ch; 2971 hc->chan[ch].slot_rx = slot_rx; 2972 hc->chan[ch].bank_rx = bank_rx; 2973 } 2974 2975 switch (protocol) { 2976 case (ISDN_P_NONE): 2977 /* disable TX fifo */ 2978 HFC_outb(hc, R_FIFO, ch << 1); 2979 HFC_wait(hc); 2980 HFC_outb(hc, A_CON_HDLC, flow_tx | 0x00 | V_IFF); 2981 HFC_outb(hc, A_SUBCH_CFG, 0); 2982 HFC_outb(hc, A_IRQ_MSK, 0); 2983 HFC_outb(hc, R_INC_RES_FIFO, V_RES_F); 2984 HFC_wait(hc); 2985 /* disable RX fifo */ 2986 HFC_outb(hc, R_FIFO, (ch << 1) | 1); 2987 HFC_wait(hc); 2988 HFC_outb(hc, A_CON_HDLC, flow_rx | 0x00); 2989 HFC_outb(hc, A_SUBCH_CFG, 0); 2990 HFC_outb(hc, A_IRQ_MSK, 0); 2991 HFC_outb(hc, R_INC_RES_FIFO, V_RES_F); 2992 HFC_wait(hc); 2993 if (hc->chan[ch].bch && hc->ctype != HFC_TYPE_E1) { 2994 hc->hw.a_st_ctrl0[hc->chan[ch].port] &= 2995 ((ch & 0x3) == 0) ? ~V_B1_EN : ~V_B2_EN; 2996 HFC_outb(hc, R_ST_SEL, hc->chan[ch].port); 2997 /* undocumented: delay after R_ST_SEL */ 2998 udelay(1); 2999 HFC_outb(hc, A_ST_CTRL0, 3000 hc->hw.a_st_ctrl0[hc->chan[ch].port]); 3001 } 3002 if (hc->chan[ch].bch) { 3003 test_and_clear_bit(FLG_HDLC, &hc->chan[ch].bch->Flags); 3004 test_and_clear_bit(FLG_TRANSPARENT, 3005 &hc->chan[ch].bch->Flags); 3006 } 3007 break; 3008 case (ISDN_P_B_RAW): /* B-channel */ 3009 3010 if (test_bit(HFC_CHIP_B410P, &hc->chip) && 3011 (hc->chan[ch].slot_rx < 0) && 3012 (hc->chan[ch].slot_tx < 0)) { 3013 3014 printk(KERN_DEBUG 3015 "Setting B-channel %d to echo cancelable " 3016 "state on PCM slot %d\n", ch, 3017 ((ch / 4) * 8) + ((ch % 4) * 4) + 1); 3018 printk(KERN_DEBUG 3019 "Enabling pass through for channel\n"); 3020 vpm_out(hc, ch, ((ch / 4) * 8) + 3021 ((ch % 4) * 4) + 1, 0x01); 3022 /* rx path */ 3023 /* S/T -> PCM */ 3024 HFC_outb(hc, R_FIFO, (ch << 1)); 3025 HFC_wait(hc); 3026 HFC_outb(hc, A_CON_HDLC, 0xc0 | V_HDLC_TRP | V_IFF); 3027 HFC_outb(hc, R_SLOT, (((ch / 4) * 8) + 3028 ((ch % 4) * 4) + 1) << 1); 3029 HFC_outb(hc, A_SL_CFG, 0x80 | (ch << 1)); 3030 3031 /* PCM -> FIFO */ 3032 HFC_outb(hc, R_FIFO, 0x20 | (ch << 1) | 1); 3033 HFC_wait(hc); 3034 HFC_outb(hc, A_CON_HDLC, 0x20 | V_HDLC_TRP | V_IFF); 3035 HFC_outb(hc, A_SUBCH_CFG, 0); 3036 HFC_outb(hc, A_IRQ_MSK, 0); 3037 if (hc->chan[ch].protocol != protocol) { 3038 HFC_outb(hc, R_INC_RES_FIFO, V_RES_F); 3039 HFC_wait(hc); 3040 } 3041 HFC_outb(hc, R_SLOT, ((((ch / 4) * 8) + 3042 ((ch % 4) * 4) + 1) << 1) | 1); 3043 HFC_outb(hc, A_SL_CFG, 0x80 | 0x20 | (ch << 1) | 1); 3044 3045 /* tx path */ 3046 /* PCM -> S/T */ 3047 HFC_outb(hc, R_FIFO, (ch << 1) | 1); 3048 HFC_wait(hc); 3049 HFC_outb(hc, A_CON_HDLC, 0xc0 | V_HDLC_TRP | V_IFF); 3050 HFC_outb(hc, R_SLOT, ((((ch / 4) * 8) + 3051 ((ch % 4) * 4)) << 1) | 1); 3052 HFC_outb(hc, A_SL_CFG, 0x80 | 0x40 | (ch << 1) | 1); 3053 3054 /* FIFO -> PCM */ 3055 HFC_outb(hc, R_FIFO, 0x20 | (ch << 1)); 3056 HFC_wait(hc); 3057 HFC_outb(hc, A_CON_HDLC, 0x20 | V_HDLC_TRP | V_IFF); 3058 HFC_outb(hc, A_SUBCH_CFG, 0); 3059 HFC_outb(hc, A_IRQ_MSK, 0); 3060 if (hc->chan[ch].protocol != protocol) { 3061 HFC_outb(hc, R_INC_RES_FIFO, V_RES_F); 3062 HFC_wait(hc); 3063 } 3064 /* tx silence */ 3065 HFC_outb_nodebug(hc, A_FIFO_DATA0_NOINC, hc->silence); 3066 HFC_outb(hc, R_SLOT, (((ch / 4) * 8) + 3067 ((ch % 4) * 4)) << 1); 3068 HFC_outb(hc, A_SL_CFG, 0x80 | 0x20 | (ch << 1)); 3069 } else { 3070 /* enable TX fifo */ 3071 HFC_outb(hc, R_FIFO, ch << 1); 3072 HFC_wait(hc); 3073 if (hc->ctype == HFC_TYPE_XHFC) 3074 HFC_outb(hc, A_CON_HDLC, flow_tx | 0x07 << 2 | 3075 V_HDLC_TRP | V_IFF); 3076 /* Enable FIFO, no interrupt */ 3077 else 3078 HFC_outb(hc, A_CON_HDLC, flow_tx | 0x00 | 3079 V_HDLC_TRP | V_IFF); 3080 HFC_outb(hc, A_SUBCH_CFG, 0); 3081 HFC_outb(hc, A_IRQ_MSK, 0); 3082 if (hc->chan[ch].protocol != protocol) { 3083 HFC_outb(hc, R_INC_RES_FIFO, V_RES_F); 3084 HFC_wait(hc); 3085 } 3086 /* tx silence */ 3087 HFC_outb_nodebug(hc, A_FIFO_DATA0_NOINC, hc->silence); 3088 /* enable RX fifo */ 3089 HFC_outb(hc, R_FIFO, (ch << 1) | 1); 3090 HFC_wait(hc); 3091 if (hc->ctype == HFC_TYPE_XHFC) 3092 HFC_outb(hc, A_CON_HDLC, flow_rx | 0x07 << 2 | 3093 V_HDLC_TRP); 3094 /* Enable FIFO, no interrupt*/ 3095 else 3096 HFC_outb(hc, A_CON_HDLC, flow_rx | 0x00 | 3097 V_HDLC_TRP); 3098 HFC_outb(hc, A_SUBCH_CFG, 0); 3099 HFC_outb(hc, A_IRQ_MSK, 0); 3100 if (hc->chan[ch].protocol != protocol) { 3101 HFC_outb(hc, R_INC_RES_FIFO, V_RES_F); 3102 HFC_wait(hc); 3103 } 3104 } 3105 if (hc->ctype != HFC_TYPE_E1) { 3106 hc->hw.a_st_ctrl0[hc->chan[ch].port] |= 3107 ((ch & 0x3) == 0) ? V_B1_EN : V_B2_EN; 3108 HFC_outb(hc, R_ST_SEL, hc->chan[ch].port); 3109 /* undocumented: delay after R_ST_SEL */ 3110 udelay(1); 3111 HFC_outb(hc, A_ST_CTRL0, 3112 hc->hw.a_st_ctrl0[hc->chan[ch].port]); 3113 } 3114 if (hc->chan[ch].bch) 3115 test_and_set_bit(FLG_TRANSPARENT, 3116 &hc->chan[ch].bch->Flags); 3117 break; 3118 case (ISDN_P_B_HDLC): /* B-channel */ 3119 case (ISDN_P_TE_S0): /* D-channel */ 3120 case (ISDN_P_NT_S0): 3121 case (ISDN_P_TE_E1): 3122 case (ISDN_P_NT_E1): 3123 /* enable TX fifo */ 3124 HFC_outb(hc, R_FIFO, ch << 1); 3125 HFC_wait(hc); 3126 if (hc->ctype == HFC_TYPE_E1 || hc->chan[ch].bch) { 3127 /* E1 or B-channel */ 3128 HFC_outb(hc, A_CON_HDLC, flow_tx | 0x04); 3129 HFC_outb(hc, A_SUBCH_CFG, 0); 3130 } else { 3131 /* D-Channel without HDLC fill flags */ 3132 HFC_outb(hc, A_CON_HDLC, flow_tx | 0x04 | V_IFF); 3133 HFC_outb(hc, A_SUBCH_CFG, 2); 3134 } 3135 HFC_outb(hc, A_IRQ_MSK, V_IRQ); 3136 HFC_outb(hc, R_INC_RES_FIFO, V_RES_F); 3137 HFC_wait(hc); 3138 /* enable RX fifo */ 3139 HFC_outb(hc, R_FIFO, (ch << 1) | 1); 3140 HFC_wait(hc); 3141 HFC_outb(hc, A_CON_HDLC, flow_rx | 0x04); 3142 if (hc->ctype == HFC_TYPE_E1 || hc->chan[ch].bch) 3143 HFC_outb(hc, A_SUBCH_CFG, 0); /* full 8 bits */ 3144 else 3145 HFC_outb(hc, A_SUBCH_CFG, 2); /* 2 bits dchannel */ 3146 HFC_outb(hc, A_IRQ_MSK, V_IRQ); 3147 HFC_outb(hc, R_INC_RES_FIFO, V_RES_F); 3148 HFC_wait(hc); 3149 if (hc->chan[ch].bch) { 3150 test_and_set_bit(FLG_HDLC, &hc->chan[ch].bch->Flags); 3151 if (hc->ctype != HFC_TYPE_E1) { 3152 hc->hw.a_st_ctrl0[hc->chan[ch].port] |= 3153 ((ch & 0x3) == 0) ? V_B1_EN : V_B2_EN; 3154 HFC_outb(hc, R_ST_SEL, hc->chan[ch].port); 3155 /* undocumented: delay after R_ST_SEL */ 3156 udelay(1); 3157 HFC_outb(hc, A_ST_CTRL0, 3158 hc->hw.a_st_ctrl0[hc->chan[ch].port]); 3159 } 3160 } 3161 break; 3162 default: 3163 printk(KERN_DEBUG "%s: protocol not known %x\n", 3164 __func__, protocol); 3165 hc->chan[ch].protocol = ISDN_P_NONE; 3166 return -ENOPROTOOPT; 3167 } 3168 hc->chan[ch].protocol = protocol; 3169 return 0; 3170 } 3171 3172 3173 /* 3174 * connect/disconnect PCM 3175 */ 3176 3177 static void 3178 hfcmulti_pcm(struct hfc_multi *hc, int ch, int slot_tx, int bank_tx, 3179 int slot_rx, int bank_rx) 3180 { 3181 if (slot_tx < 0 || slot_rx < 0 || bank_tx < 0 || bank_rx < 0) { 3182 /* disable PCM */ 3183 mode_hfcmulti(hc, ch, hc->chan[ch].protocol, -1, 0, -1, 0); 3184 return; 3185 } 3186 3187 /* enable pcm */ 3188 mode_hfcmulti(hc, ch, hc->chan[ch].protocol, slot_tx, bank_tx, 3189 slot_rx, bank_rx); 3190 } 3191 3192 /* 3193 * set/disable conference 3194 */ 3195 3196 static void 3197 hfcmulti_conf(struct hfc_multi *hc, int ch, int num) 3198 { 3199 if (num >= 0 && num <= 7) 3200 hc->chan[ch].conf = num; 3201 else 3202 hc->chan[ch].conf = -1; 3203 mode_hfcmulti(hc, ch, hc->chan[ch].protocol, hc->chan[ch].slot_tx, 3204 hc->chan[ch].bank_tx, hc->chan[ch].slot_rx, 3205 hc->chan[ch].bank_rx); 3206 } 3207 3208 3209 /* 3210 * set/disable sample loop 3211 */ 3212 3213 /* NOTE: this function is experimental and therefore disabled */ 3214 3215 /* 3216 * Layer 1 callback function 3217 */ 3218 static int 3219 hfcm_l1callback(struct dchannel *dch, u_int cmd) 3220 { 3221 struct hfc_multi *hc = dch->hw; 3222 u_long flags; 3223 3224 switch (cmd) { 3225 case INFO3_P8: 3226 case INFO3_P10: 3227 break; 3228 case HW_RESET_REQ: 3229 /* start activation */ 3230 spin_lock_irqsave(&hc->lock, flags); 3231 if (hc->ctype == HFC_TYPE_E1) { 3232 if (debug & DEBUG_HFCMULTI_MSG) 3233 printk(KERN_DEBUG 3234 "%s: HW_RESET_REQ no BRI\n", 3235 __func__); 3236 } else { 3237 HFC_outb(hc, R_ST_SEL, hc->chan[dch->slot].port); 3238 /* undocumented: delay after R_ST_SEL */ 3239 udelay(1); 3240 HFC_outb(hc, A_ST_WR_STATE, V_ST_LD_STA | 3); /* F3 */ 3241 udelay(6); /* wait at least 5,21us */ 3242 HFC_outb(hc, A_ST_WR_STATE, 3); 3243 HFC_outb(hc, A_ST_WR_STATE, 3 | (V_ST_ACT * 3)); 3244 /* activate */ 3245 } 3246 spin_unlock_irqrestore(&hc->lock, flags); 3247 l1_event(dch->l1, HW_POWERUP_IND); 3248 break; 3249 case HW_DEACT_REQ: 3250 /* start deactivation */ 3251 spin_lock_irqsave(&hc->lock, flags); 3252 if (hc->ctype == HFC_TYPE_E1) { 3253 if (debug & DEBUG_HFCMULTI_MSG) 3254 printk(KERN_DEBUG 3255 "%s: HW_DEACT_REQ no BRI\n", 3256 __func__); 3257 } else { 3258 HFC_outb(hc, R_ST_SEL, hc->chan[dch->slot].port); 3259 /* undocumented: delay after R_ST_SEL */ 3260 udelay(1); 3261 HFC_outb(hc, A_ST_WR_STATE, V_ST_ACT * 2); 3262 /* deactivate */ 3263 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 3264 hc->syncronized &= 3265 ~(1 << hc->chan[dch->slot].port); 3266 plxsd_checksync(hc, 0); 3267 } 3268 } 3269 skb_queue_purge(&dch->squeue); 3270 if (dch->tx_skb) { 3271 dev_kfree_skb(dch->tx_skb); 3272 dch->tx_skb = NULL; 3273 } 3274 dch->tx_idx = 0; 3275 if (dch->rx_skb) { 3276 dev_kfree_skb(dch->rx_skb); 3277 dch->rx_skb = NULL; 3278 } 3279 test_and_clear_bit(FLG_TX_BUSY, &dch->Flags); 3280 if (test_and_clear_bit(FLG_BUSY_TIMER, &dch->Flags)) 3281 del_timer(&dch->timer); 3282 spin_unlock_irqrestore(&hc->lock, flags); 3283 break; 3284 case HW_POWERUP_REQ: 3285 spin_lock_irqsave(&hc->lock, flags); 3286 if (hc->ctype == HFC_TYPE_E1) { 3287 if (debug & DEBUG_HFCMULTI_MSG) 3288 printk(KERN_DEBUG 3289 "%s: HW_POWERUP_REQ no BRI\n", 3290 __func__); 3291 } else { 3292 HFC_outb(hc, R_ST_SEL, hc->chan[dch->slot].port); 3293 /* undocumented: delay after R_ST_SEL */ 3294 udelay(1); 3295 HFC_outb(hc, A_ST_WR_STATE, 3 | 0x10); /* activate */ 3296 udelay(6); /* wait at least 5,21us */ 3297 HFC_outb(hc, A_ST_WR_STATE, 3); /* activate */ 3298 } 3299 spin_unlock_irqrestore(&hc->lock, flags); 3300 break; 3301 case PH_ACTIVATE_IND: 3302 test_and_set_bit(FLG_ACTIVE, &dch->Flags); 3303 _queue_data(&dch->dev.D, cmd, MISDN_ID_ANY, 0, NULL, 3304 GFP_ATOMIC); 3305 break; 3306 case PH_DEACTIVATE_IND: 3307 test_and_clear_bit(FLG_ACTIVE, &dch->Flags); 3308 _queue_data(&dch->dev.D, cmd, MISDN_ID_ANY, 0, NULL, 3309 GFP_ATOMIC); 3310 break; 3311 default: 3312 if (dch->debug & DEBUG_HW) 3313 printk(KERN_DEBUG "%s: unknown command %x\n", 3314 __func__, cmd); 3315 return -1; 3316 } 3317 return 0; 3318 } 3319 3320 /* 3321 * Layer2 -> Layer 1 Transfer 3322 */ 3323 3324 static int 3325 handle_dmsg(struct mISDNchannel *ch, struct sk_buff *skb) 3326 { 3327 struct mISDNdevice *dev = container_of(ch, struct mISDNdevice, D); 3328 struct dchannel *dch = container_of(dev, struct dchannel, dev); 3329 struct hfc_multi *hc = dch->hw; 3330 struct mISDNhead *hh = mISDN_HEAD_P(skb); 3331 int ret = -EINVAL; 3332 unsigned int id; 3333 u_long flags; 3334 3335 switch (hh->prim) { 3336 case PH_DATA_REQ: 3337 if (skb->len < 1) 3338 break; 3339 spin_lock_irqsave(&hc->lock, flags); 3340 ret = dchannel_senddata(dch, skb); 3341 if (ret > 0) { /* direct TX */ 3342 id = hh->id; /* skb can be freed */ 3343 hfcmulti_tx(hc, dch->slot); 3344 ret = 0; 3345 /* start fifo */ 3346 HFC_outb(hc, R_FIFO, 0); 3347 HFC_wait(hc); 3348 spin_unlock_irqrestore(&hc->lock, flags); 3349 queue_ch_frame(ch, PH_DATA_CNF, id, NULL); 3350 } else 3351 spin_unlock_irqrestore(&hc->lock, flags); 3352 return ret; 3353 case PH_ACTIVATE_REQ: 3354 if (dch->dev.D.protocol != ISDN_P_TE_S0) { 3355 spin_lock_irqsave(&hc->lock, flags); 3356 ret = 0; 3357 if (debug & DEBUG_HFCMULTI_MSG) 3358 printk(KERN_DEBUG 3359 "%s: PH_ACTIVATE port %d (0..%d)\n", 3360 __func__, hc->chan[dch->slot].port, 3361 hc->ports - 1); 3362 /* start activation */ 3363 if (hc->ctype == HFC_TYPE_E1) { 3364 ph_state_change(dch); 3365 if (debug & DEBUG_HFCMULTI_STATE) 3366 printk(KERN_DEBUG 3367 "%s: E1 report state %x \n", 3368 __func__, dch->state); 3369 } else { 3370 HFC_outb(hc, R_ST_SEL, 3371 hc->chan[dch->slot].port); 3372 /* undocumented: delay after R_ST_SEL */ 3373 udelay(1); 3374 HFC_outb(hc, A_ST_WR_STATE, V_ST_LD_STA | 1); 3375 /* G1 */ 3376 udelay(6); /* wait at least 5,21us */ 3377 HFC_outb(hc, A_ST_WR_STATE, 1); 3378 HFC_outb(hc, A_ST_WR_STATE, 1 | 3379 (V_ST_ACT * 3)); /* activate */ 3380 dch->state = 1; 3381 } 3382 spin_unlock_irqrestore(&hc->lock, flags); 3383 } else 3384 ret = l1_event(dch->l1, hh->prim); 3385 break; 3386 case PH_DEACTIVATE_REQ: 3387 test_and_clear_bit(FLG_L2_ACTIVATED, &dch->Flags); 3388 if (dch->dev.D.protocol != ISDN_P_TE_S0) { 3389 spin_lock_irqsave(&hc->lock, flags); 3390 if (debug & DEBUG_HFCMULTI_MSG) 3391 printk(KERN_DEBUG 3392 "%s: PH_DEACTIVATE port %d (0..%d)\n", 3393 __func__, hc->chan[dch->slot].port, 3394 hc->ports - 1); 3395 /* start deactivation */ 3396 if (hc->ctype == HFC_TYPE_E1) { 3397 if (debug & DEBUG_HFCMULTI_MSG) 3398 printk(KERN_DEBUG 3399 "%s: PH_DEACTIVATE no BRI\n", 3400 __func__); 3401 } else { 3402 HFC_outb(hc, R_ST_SEL, 3403 hc->chan[dch->slot].port); 3404 /* undocumented: delay after R_ST_SEL */ 3405 udelay(1); 3406 HFC_outb(hc, A_ST_WR_STATE, V_ST_ACT * 2); 3407 /* deactivate */ 3408 dch->state = 1; 3409 } 3410 skb_queue_purge(&dch->squeue); 3411 if (dch->tx_skb) { 3412 dev_kfree_skb(dch->tx_skb); 3413 dch->tx_skb = NULL; 3414 } 3415 dch->tx_idx = 0; 3416 if (dch->rx_skb) { 3417 dev_kfree_skb(dch->rx_skb); 3418 dch->rx_skb = NULL; 3419 } 3420 test_and_clear_bit(FLG_TX_BUSY, &dch->Flags); 3421 if (test_and_clear_bit(FLG_BUSY_TIMER, &dch->Flags)) 3422 del_timer(&dch->timer); 3423 #ifdef FIXME 3424 if (test_and_clear_bit(FLG_L1_BUSY, &dch->Flags)) 3425 dchannel_sched_event(&hc->dch, D_CLEARBUSY); 3426 #endif 3427 ret = 0; 3428 spin_unlock_irqrestore(&hc->lock, flags); 3429 } else 3430 ret = l1_event(dch->l1, hh->prim); 3431 break; 3432 } 3433 if (!ret) 3434 dev_kfree_skb(skb); 3435 return ret; 3436 } 3437 3438 static void 3439 deactivate_bchannel(struct bchannel *bch) 3440 { 3441 struct hfc_multi *hc = bch->hw; 3442 u_long flags; 3443 3444 spin_lock_irqsave(&hc->lock, flags); 3445 mISDN_clear_bchannel(bch); 3446 hc->chan[bch->slot].coeff_count = 0; 3447 hc->chan[bch->slot].rx_off = 0; 3448 hc->chan[bch->slot].conf = -1; 3449 mode_hfcmulti(hc, bch->slot, ISDN_P_NONE, -1, 0, -1, 0); 3450 spin_unlock_irqrestore(&hc->lock, flags); 3451 } 3452 3453 static int 3454 handle_bmsg(struct mISDNchannel *ch, struct sk_buff *skb) 3455 { 3456 struct bchannel *bch = container_of(ch, struct bchannel, ch); 3457 struct hfc_multi *hc = bch->hw; 3458 int ret = -EINVAL; 3459 struct mISDNhead *hh = mISDN_HEAD_P(skb); 3460 unsigned long flags; 3461 3462 switch (hh->prim) { 3463 case PH_DATA_REQ: 3464 if (!skb->len) 3465 break; 3466 spin_lock_irqsave(&hc->lock, flags); 3467 ret = bchannel_senddata(bch, skb); 3468 if (ret > 0) { /* direct TX */ 3469 hfcmulti_tx(hc, bch->slot); 3470 ret = 0; 3471 /* start fifo */ 3472 HFC_outb_nodebug(hc, R_FIFO, 0); 3473 HFC_wait_nodebug(hc); 3474 } 3475 spin_unlock_irqrestore(&hc->lock, flags); 3476 return ret; 3477 case PH_ACTIVATE_REQ: 3478 if (debug & DEBUG_HFCMULTI_MSG) 3479 printk(KERN_DEBUG "%s: PH_ACTIVATE ch %d (0..32)\n", 3480 __func__, bch->slot); 3481 spin_lock_irqsave(&hc->lock, flags); 3482 /* activate B-channel if not already activated */ 3483 if (!test_and_set_bit(FLG_ACTIVE, &bch->Flags)) { 3484 hc->chan[bch->slot].txpending = 0; 3485 ret = mode_hfcmulti(hc, bch->slot, 3486 ch->protocol, 3487 hc->chan[bch->slot].slot_tx, 3488 hc->chan[bch->slot].bank_tx, 3489 hc->chan[bch->slot].slot_rx, 3490 hc->chan[bch->slot].bank_rx); 3491 if (!ret) { 3492 if (ch->protocol == ISDN_P_B_RAW && !hc->dtmf 3493 && test_bit(HFC_CHIP_DTMF, &hc->chip)) { 3494 /* start decoder */ 3495 hc->dtmf = 1; 3496 if (debug & DEBUG_HFCMULTI_DTMF) 3497 printk(KERN_DEBUG 3498 "%s: start dtmf decoder\n", 3499 __func__); 3500 HFC_outb(hc, R_DTMF, hc->hw.r_dtmf | 3501 V_RST_DTMF); 3502 } 3503 } 3504 } else 3505 ret = 0; 3506 spin_unlock_irqrestore(&hc->lock, flags); 3507 if (!ret) 3508 _queue_data(ch, PH_ACTIVATE_IND, MISDN_ID_ANY, 0, NULL, 3509 GFP_KERNEL); 3510 break; 3511 case PH_CONTROL_REQ: 3512 spin_lock_irqsave(&hc->lock, flags); 3513 switch (hh->id) { 3514 case HFC_SPL_LOOP_ON: /* set sample loop */ 3515 if (debug & DEBUG_HFCMULTI_MSG) 3516 printk(KERN_DEBUG 3517 "%s: HFC_SPL_LOOP_ON (len = %d)\n", 3518 __func__, skb->len); 3519 ret = 0; 3520 break; 3521 case HFC_SPL_LOOP_OFF: /* set silence */ 3522 if (debug & DEBUG_HFCMULTI_MSG) 3523 printk(KERN_DEBUG "%s: HFC_SPL_LOOP_OFF\n", 3524 __func__); 3525 ret = 0; 3526 break; 3527 default: 3528 printk(KERN_ERR 3529 "%s: unknown PH_CONTROL_REQ info %x\n", 3530 __func__, hh->id); 3531 ret = -EINVAL; 3532 } 3533 spin_unlock_irqrestore(&hc->lock, flags); 3534 break; 3535 case PH_DEACTIVATE_REQ: 3536 deactivate_bchannel(bch); /* locked there */ 3537 _queue_data(ch, PH_DEACTIVATE_IND, MISDN_ID_ANY, 0, NULL, 3538 GFP_KERNEL); 3539 ret = 0; 3540 break; 3541 } 3542 if (!ret) 3543 dev_kfree_skb(skb); 3544 return ret; 3545 } 3546 3547 /* 3548 * bchannel control function 3549 */ 3550 static int 3551 channel_bctrl(struct bchannel *bch, struct mISDN_ctrl_req *cq) 3552 { 3553 int ret = 0; 3554 struct dsp_features *features = 3555 (struct dsp_features *)(*((u_long *)&cq->p1)); 3556 struct hfc_multi *hc = bch->hw; 3557 int slot_tx; 3558 int bank_tx; 3559 int slot_rx; 3560 int bank_rx; 3561 int num; 3562 3563 switch (cq->op) { 3564 case MISDN_CTRL_GETOP: 3565 ret = mISDN_ctrl_bchannel(bch, cq); 3566 cq->op |= MISDN_CTRL_HFC_OP | MISDN_CTRL_HW_FEATURES_OP; 3567 break; 3568 case MISDN_CTRL_RX_OFF: /* turn off / on rx stream */ 3569 ret = mISDN_ctrl_bchannel(bch, cq); 3570 hc->chan[bch->slot].rx_off = !!cq->p1; 3571 if (!hc->chan[bch->slot].rx_off) { 3572 /* reset fifo on rx on */ 3573 HFC_outb_nodebug(hc, R_FIFO, (bch->slot << 1) | 1); 3574 HFC_wait_nodebug(hc); 3575 HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_RES_F); 3576 HFC_wait_nodebug(hc); 3577 } 3578 if (debug & DEBUG_HFCMULTI_MSG) 3579 printk(KERN_DEBUG "%s: RX_OFF request (nr=%d off=%d)\n", 3580 __func__, bch->nr, hc->chan[bch->slot].rx_off); 3581 break; 3582 case MISDN_CTRL_FILL_EMPTY: 3583 ret = mISDN_ctrl_bchannel(bch, cq); 3584 hc->silence = bch->fill[0]; 3585 memset(hc->silence_data, hc->silence, sizeof(hc->silence_data)); 3586 break; 3587 case MISDN_CTRL_HW_FEATURES: /* fill features structure */ 3588 if (debug & DEBUG_HFCMULTI_MSG) 3589 printk(KERN_DEBUG "%s: HW_FEATURE request\n", 3590 __func__); 3591 /* create confirm */ 3592 features->hfc_id = hc->id; 3593 if (test_bit(HFC_CHIP_DTMF, &hc->chip)) 3594 features->hfc_dtmf = 1; 3595 if (test_bit(HFC_CHIP_CONF, &hc->chip)) 3596 features->hfc_conf = 1; 3597 features->hfc_loops = 0; 3598 if (test_bit(HFC_CHIP_B410P, &hc->chip)) { 3599 features->hfc_echocanhw = 1; 3600 } else { 3601 features->pcm_id = hc->pcm; 3602 features->pcm_slots = hc->slots; 3603 features->pcm_banks = 2; 3604 } 3605 break; 3606 case MISDN_CTRL_HFC_PCM_CONN: /* connect to pcm timeslot (0..N) */ 3607 slot_tx = cq->p1 & 0xff; 3608 bank_tx = cq->p1 >> 8; 3609 slot_rx = cq->p2 & 0xff; 3610 bank_rx = cq->p2 >> 8; 3611 if (debug & DEBUG_HFCMULTI_MSG) 3612 printk(KERN_DEBUG 3613 "%s: HFC_PCM_CONN slot %d bank %d (TX) " 3614 "slot %d bank %d (RX)\n", 3615 __func__, slot_tx, bank_tx, 3616 slot_rx, bank_rx); 3617 if (slot_tx < hc->slots && bank_tx <= 2 && 3618 slot_rx < hc->slots && bank_rx <= 2) 3619 hfcmulti_pcm(hc, bch->slot, 3620 slot_tx, bank_tx, slot_rx, bank_rx); 3621 else { 3622 printk(KERN_WARNING 3623 "%s: HFC_PCM_CONN slot %d bank %d (TX) " 3624 "slot %d bank %d (RX) out of range\n", 3625 __func__, slot_tx, bank_tx, 3626 slot_rx, bank_rx); 3627 ret = -EINVAL; 3628 } 3629 break; 3630 case MISDN_CTRL_HFC_PCM_DISC: /* release interface from pcm timeslot */ 3631 if (debug & DEBUG_HFCMULTI_MSG) 3632 printk(KERN_DEBUG "%s: HFC_PCM_DISC\n", 3633 __func__); 3634 hfcmulti_pcm(hc, bch->slot, -1, 0, -1, 0); 3635 break; 3636 case MISDN_CTRL_HFC_CONF_JOIN: /* join conference (0..7) */ 3637 num = cq->p1 & 0xff; 3638 if (debug & DEBUG_HFCMULTI_MSG) 3639 printk(KERN_DEBUG "%s: HFC_CONF_JOIN conf %d\n", 3640 __func__, num); 3641 if (num <= 7) 3642 hfcmulti_conf(hc, bch->slot, num); 3643 else { 3644 printk(KERN_WARNING 3645 "%s: HW_CONF_JOIN conf %d out of range\n", 3646 __func__, num); 3647 ret = -EINVAL; 3648 } 3649 break; 3650 case MISDN_CTRL_HFC_CONF_SPLIT: /* split conference */ 3651 if (debug & DEBUG_HFCMULTI_MSG) 3652 printk(KERN_DEBUG "%s: HFC_CONF_SPLIT\n", __func__); 3653 hfcmulti_conf(hc, bch->slot, -1); 3654 break; 3655 case MISDN_CTRL_HFC_ECHOCAN_ON: 3656 if (debug & DEBUG_HFCMULTI_MSG) 3657 printk(KERN_DEBUG "%s: HFC_ECHOCAN_ON\n", __func__); 3658 if (test_bit(HFC_CHIP_B410P, &hc->chip)) 3659 vpm_echocan_on(hc, bch->slot, cq->p1); 3660 else 3661 ret = -EINVAL; 3662 break; 3663 3664 case MISDN_CTRL_HFC_ECHOCAN_OFF: 3665 if (debug & DEBUG_HFCMULTI_MSG) 3666 printk(KERN_DEBUG "%s: HFC_ECHOCAN_OFF\n", 3667 __func__); 3668 if (test_bit(HFC_CHIP_B410P, &hc->chip)) 3669 vpm_echocan_off(hc, bch->slot); 3670 else 3671 ret = -EINVAL; 3672 break; 3673 default: 3674 ret = mISDN_ctrl_bchannel(bch, cq); 3675 break; 3676 } 3677 return ret; 3678 } 3679 3680 static int 3681 hfcm_bctrl(struct mISDNchannel *ch, u_int cmd, void *arg) 3682 { 3683 struct bchannel *bch = container_of(ch, struct bchannel, ch); 3684 struct hfc_multi *hc = bch->hw; 3685 int err = -EINVAL; 3686 u_long flags; 3687 3688 if (bch->debug & DEBUG_HW) 3689 printk(KERN_DEBUG "%s: cmd:%x %p\n", 3690 __func__, cmd, arg); 3691 switch (cmd) { 3692 case CLOSE_CHANNEL: 3693 test_and_clear_bit(FLG_OPEN, &bch->Flags); 3694 deactivate_bchannel(bch); /* locked there */ 3695 ch->protocol = ISDN_P_NONE; 3696 ch->peer = NULL; 3697 module_put(THIS_MODULE); 3698 err = 0; 3699 break; 3700 case CONTROL_CHANNEL: 3701 spin_lock_irqsave(&hc->lock, flags); 3702 err = channel_bctrl(bch, arg); 3703 spin_unlock_irqrestore(&hc->lock, flags); 3704 break; 3705 default: 3706 printk(KERN_WARNING "%s: unknown prim(%x)\n", 3707 __func__, cmd); 3708 } 3709 return err; 3710 } 3711 3712 /* 3713 * handle D-channel events 3714 * 3715 * handle state change event 3716 */ 3717 static void 3718 ph_state_change(struct dchannel *dch) 3719 { 3720 struct hfc_multi *hc; 3721 int ch, i; 3722 3723 if (!dch) { 3724 printk(KERN_WARNING "%s: ERROR given dch is NULL\n", __func__); 3725 return; 3726 } 3727 hc = dch->hw; 3728 ch = dch->slot; 3729 3730 if (hc->ctype == HFC_TYPE_E1) { 3731 if (dch->dev.D.protocol == ISDN_P_TE_E1) { 3732 if (debug & DEBUG_HFCMULTI_STATE) 3733 printk(KERN_DEBUG 3734 "%s: E1 TE (id=%d) newstate %x\n", 3735 __func__, hc->id, dch->state); 3736 } else { 3737 if (debug & DEBUG_HFCMULTI_STATE) 3738 printk(KERN_DEBUG 3739 "%s: E1 NT (id=%d) newstate %x\n", 3740 __func__, hc->id, dch->state); 3741 } 3742 switch (dch->state) { 3743 case (1): 3744 if (hc->e1_state != 1) { 3745 for (i = 1; i <= 31; i++) { 3746 /* reset fifos on e1 activation */ 3747 HFC_outb_nodebug(hc, R_FIFO, 3748 (i << 1) | 1); 3749 HFC_wait_nodebug(hc); 3750 HFC_outb_nodebug(hc, R_INC_RES_FIFO, 3751 V_RES_F); 3752 HFC_wait_nodebug(hc); 3753 } 3754 } 3755 test_and_set_bit(FLG_ACTIVE, &dch->Flags); 3756 _queue_data(&dch->dev.D, PH_ACTIVATE_IND, 3757 MISDN_ID_ANY, 0, NULL, GFP_ATOMIC); 3758 break; 3759 3760 default: 3761 if (hc->e1_state != 1) 3762 return; 3763 test_and_clear_bit(FLG_ACTIVE, &dch->Flags); 3764 _queue_data(&dch->dev.D, PH_DEACTIVATE_IND, 3765 MISDN_ID_ANY, 0, NULL, GFP_ATOMIC); 3766 } 3767 hc->e1_state = dch->state; 3768 } else { 3769 if (dch->dev.D.protocol == ISDN_P_TE_S0) { 3770 if (debug & DEBUG_HFCMULTI_STATE) 3771 printk(KERN_DEBUG 3772 "%s: S/T TE newstate %x\n", 3773 __func__, dch->state); 3774 switch (dch->state) { 3775 case (0): 3776 l1_event(dch->l1, HW_RESET_IND); 3777 break; 3778 case (3): 3779 l1_event(dch->l1, HW_DEACT_IND); 3780 break; 3781 case (5): 3782 case (8): 3783 l1_event(dch->l1, ANYSIGNAL); 3784 break; 3785 case (6): 3786 l1_event(dch->l1, INFO2); 3787 break; 3788 case (7): 3789 l1_event(dch->l1, INFO4_P8); 3790 break; 3791 } 3792 } else { 3793 if (debug & DEBUG_HFCMULTI_STATE) 3794 printk(KERN_DEBUG "%s: S/T NT newstate %x\n", 3795 __func__, dch->state); 3796 switch (dch->state) { 3797 case (2): 3798 if (hc->chan[ch].nt_timer == 0) { 3799 hc->chan[ch].nt_timer = -1; 3800 HFC_outb(hc, R_ST_SEL, 3801 hc->chan[ch].port); 3802 /* undocumented: delay after R_ST_SEL */ 3803 udelay(1); 3804 HFC_outb(hc, A_ST_WR_STATE, 4 | 3805 V_ST_LD_STA); /* G4 */ 3806 udelay(6); /* wait at least 5,21us */ 3807 HFC_outb(hc, A_ST_WR_STATE, 4); 3808 dch->state = 4; 3809 } else { 3810 /* one extra count for the next event */ 3811 hc->chan[ch].nt_timer = 3812 nt_t1_count[poll_timer] + 1; 3813 HFC_outb(hc, R_ST_SEL, 3814 hc->chan[ch].port); 3815 /* undocumented: delay after R_ST_SEL */ 3816 udelay(1); 3817 /* allow G2 -> G3 transition */ 3818 HFC_outb(hc, A_ST_WR_STATE, 2 | 3819 V_SET_G2_G3); 3820 } 3821 break; 3822 case (1): 3823 hc->chan[ch].nt_timer = -1; 3824 test_and_clear_bit(FLG_ACTIVE, &dch->Flags); 3825 _queue_data(&dch->dev.D, PH_DEACTIVATE_IND, 3826 MISDN_ID_ANY, 0, NULL, GFP_ATOMIC); 3827 break; 3828 case (4): 3829 hc->chan[ch].nt_timer = -1; 3830 break; 3831 case (3): 3832 hc->chan[ch].nt_timer = -1; 3833 test_and_set_bit(FLG_ACTIVE, &dch->Flags); 3834 _queue_data(&dch->dev.D, PH_ACTIVATE_IND, 3835 MISDN_ID_ANY, 0, NULL, GFP_ATOMIC); 3836 break; 3837 } 3838 } 3839 } 3840 } 3841 3842 /* 3843 * called for card mode init message 3844 */ 3845 3846 static void 3847 hfcmulti_initmode(struct dchannel *dch) 3848 { 3849 struct hfc_multi *hc = dch->hw; 3850 u_char a_st_wr_state, r_e1_wr_sta; 3851 int i, pt; 3852 3853 if (debug & DEBUG_HFCMULTI_INIT) 3854 printk(KERN_DEBUG "%s: entered\n", __func__); 3855 3856 i = dch->slot; 3857 pt = hc->chan[i].port; 3858 if (hc->ctype == HFC_TYPE_E1) { 3859 /* E1 */ 3860 hc->chan[hc->dnum[pt]].slot_tx = -1; 3861 hc->chan[hc->dnum[pt]].slot_rx = -1; 3862 hc->chan[hc->dnum[pt]].conf = -1; 3863 if (hc->dnum[pt]) { 3864 mode_hfcmulti(hc, dch->slot, dch->dev.D.protocol, 3865 -1, 0, -1, 0); 3866 timer_setup(&dch->timer, hfcmulti_dbusy_timer, 0); 3867 } 3868 for (i = 1; i <= 31; i++) { 3869 if (!((1 << i) & hc->bmask[pt])) /* skip unused chan */ 3870 continue; 3871 hc->chan[i].slot_tx = -1; 3872 hc->chan[i].slot_rx = -1; 3873 hc->chan[i].conf = -1; 3874 mode_hfcmulti(hc, i, ISDN_P_NONE, -1, 0, -1, 0); 3875 } 3876 } 3877 if (hc->ctype == HFC_TYPE_E1 && pt == 0) { 3878 /* E1, port 0 */ 3879 dch = hc->chan[hc->dnum[0]].dch; 3880 if (test_bit(HFC_CFG_REPORT_LOS, &hc->chan[hc->dnum[0]].cfg)) { 3881 HFC_outb(hc, R_LOS0, 255); /* 2 ms */ 3882 HFC_outb(hc, R_LOS1, 255); /* 512 ms */ 3883 } 3884 if (test_bit(HFC_CFG_OPTICAL, &hc->chan[hc->dnum[0]].cfg)) { 3885 HFC_outb(hc, R_RX0, 0); 3886 hc->hw.r_tx0 = 0 | V_OUT_EN; 3887 } else { 3888 HFC_outb(hc, R_RX0, 1); 3889 hc->hw.r_tx0 = 1 | V_OUT_EN; 3890 } 3891 hc->hw.r_tx1 = V_ATX | V_NTRI; 3892 HFC_outb(hc, R_TX0, hc->hw.r_tx0); 3893 HFC_outb(hc, R_TX1, hc->hw.r_tx1); 3894 HFC_outb(hc, R_TX_FR0, 0x00); 3895 HFC_outb(hc, R_TX_FR1, 0xf8); 3896 3897 if (test_bit(HFC_CFG_CRC4, &hc->chan[hc->dnum[0]].cfg)) 3898 HFC_outb(hc, R_TX_FR2, V_TX_MF | V_TX_E | V_NEG_E); 3899 3900 HFC_outb(hc, R_RX_FR0, V_AUTO_RESYNC | V_AUTO_RECO | 0); 3901 3902 if (test_bit(HFC_CFG_CRC4, &hc->chan[hc->dnum[0]].cfg)) 3903 HFC_outb(hc, R_RX_FR1, V_RX_MF | V_RX_MF_SYNC); 3904 3905 if (dch->dev.D.protocol == ISDN_P_NT_E1) { 3906 if (debug & DEBUG_HFCMULTI_INIT) 3907 printk(KERN_DEBUG "%s: E1 port is NT-mode\n", 3908 __func__); 3909 r_e1_wr_sta = 0; /* G0 */ 3910 hc->e1_getclock = 0; 3911 } else { 3912 if (debug & DEBUG_HFCMULTI_INIT) 3913 printk(KERN_DEBUG "%s: E1 port is TE-mode\n", 3914 __func__); 3915 r_e1_wr_sta = 0; /* F0 */ 3916 hc->e1_getclock = 1; 3917 } 3918 if (test_bit(HFC_CHIP_RX_SYNC, &hc->chip)) 3919 HFC_outb(hc, R_SYNC_OUT, V_SYNC_E1_RX); 3920 else 3921 HFC_outb(hc, R_SYNC_OUT, 0); 3922 if (test_bit(HFC_CHIP_E1CLOCK_GET, &hc->chip)) 3923 hc->e1_getclock = 1; 3924 if (test_bit(HFC_CHIP_E1CLOCK_PUT, &hc->chip)) 3925 hc->e1_getclock = 0; 3926 if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) { 3927 /* SLAVE (clock master) */ 3928 if (debug & DEBUG_HFCMULTI_INIT) 3929 printk(KERN_DEBUG 3930 "%s: E1 port is clock master " 3931 "(clock from PCM)\n", __func__); 3932 HFC_outb(hc, R_SYNC_CTRL, V_EXT_CLK_SYNC | V_PCM_SYNC); 3933 } else { 3934 if (hc->e1_getclock) { 3935 /* MASTER (clock slave) */ 3936 if (debug & DEBUG_HFCMULTI_INIT) 3937 printk(KERN_DEBUG 3938 "%s: E1 port is clock slave " 3939 "(clock to PCM)\n", __func__); 3940 HFC_outb(hc, R_SYNC_CTRL, V_SYNC_OFFS); 3941 } else { 3942 /* MASTER (clock master) */ 3943 if (debug & DEBUG_HFCMULTI_INIT) 3944 printk(KERN_DEBUG "%s: E1 port is " 3945 "clock master " 3946 "(clock from QUARTZ)\n", 3947 __func__); 3948 HFC_outb(hc, R_SYNC_CTRL, V_EXT_CLK_SYNC | 3949 V_PCM_SYNC | V_JATT_OFF); 3950 HFC_outb(hc, R_SYNC_OUT, 0); 3951 } 3952 } 3953 HFC_outb(hc, R_JATT_ATT, 0x9c); /* undoc register */ 3954 HFC_outb(hc, R_PWM_MD, V_PWM0_MD); 3955 HFC_outb(hc, R_PWM0, 0x50); 3956 HFC_outb(hc, R_PWM1, 0xff); 3957 /* state machine setup */ 3958 HFC_outb(hc, R_E1_WR_STA, r_e1_wr_sta | V_E1_LD_STA); 3959 udelay(6); /* wait at least 5,21us */ 3960 HFC_outb(hc, R_E1_WR_STA, r_e1_wr_sta); 3961 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 3962 hc->syncronized = 0; 3963 plxsd_checksync(hc, 0); 3964 } 3965 } 3966 if (hc->ctype != HFC_TYPE_E1) { 3967 /* ST */ 3968 hc->chan[i].slot_tx = -1; 3969 hc->chan[i].slot_rx = -1; 3970 hc->chan[i].conf = -1; 3971 mode_hfcmulti(hc, i, dch->dev.D.protocol, -1, 0, -1, 0); 3972 timer_setup(&dch->timer, hfcmulti_dbusy_timer, 0); 3973 hc->chan[i - 2].slot_tx = -1; 3974 hc->chan[i - 2].slot_rx = -1; 3975 hc->chan[i - 2].conf = -1; 3976 mode_hfcmulti(hc, i - 2, ISDN_P_NONE, -1, 0, -1, 0); 3977 hc->chan[i - 1].slot_tx = -1; 3978 hc->chan[i - 1].slot_rx = -1; 3979 hc->chan[i - 1].conf = -1; 3980 mode_hfcmulti(hc, i - 1, ISDN_P_NONE, -1, 0, -1, 0); 3981 /* select interface */ 3982 HFC_outb(hc, R_ST_SEL, pt); 3983 /* undocumented: delay after R_ST_SEL */ 3984 udelay(1); 3985 if (dch->dev.D.protocol == ISDN_P_NT_S0) { 3986 if (debug & DEBUG_HFCMULTI_INIT) 3987 printk(KERN_DEBUG 3988 "%s: ST port %d is NT-mode\n", 3989 __func__, pt); 3990 /* clock delay */ 3991 HFC_outb(hc, A_ST_CLK_DLY, clockdelay_nt); 3992 a_st_wr_state = 1; /* G1 */ 3993 hc->hw.a_st_ctrl0[pt] = V_ST_MD; 3994 } else { 3995 if (debug & DEBUG_HFCMULTI_INIT) 3996 printk(KERN_DEBUG 3997 "%s: ST port %d is TE-mode\n", 3998 __func__, pt); 3999 /* clock delay */ 4000 HFC_outb(hc, A_ST_CLK_DLY, clockdelay_te); 4001 a_st_wr_state = 2; /* F2 */ 4002 hc->hw.a_st_ctrl0[pt] = 0; 4003 } 4004 if (!test_bit(HFC_CFG_NONCAP_TX, &hc->chan[i].cfg)) 4005 hc->hw.a_st_ctrl0[pt] |= V_TX_LI; 4006 if (hc->ctype == HFC_TYPE_XHFC) { 4007 hc->hw.a_st_ctrl0[pt] |= 0x40 /* V_ST_PU_CTRL */; 4008 HFC_outb(hc, 0x35 /* A_ST_CTRL3 */, 4009 0x7c << 1 /* V_ST_PULSE */); 4010 } 4011 /* line setup */ 4012 HFC_outb(hc, A_ST_CTRL0, hc->hw.a_st_ctrl0[pt]); 4013 /* disable E-channel */ 4014 if ((dch->dev.D.protocol == ISDN_P_NT_S0) || 4015 test_bit(HFC_CFG_DIS_ECHANNEL, &hc->chan[i].cfg)) 4016 HFC_outb(hc, A_ST_CTRL1, V_E_IGNO); 4017 else 4018 HFC_outb(hc, A_ST_CTRL1, 0); 4019 /* enable B-channel receive */ 4020 HFC_outb(hc, A_ST_CTRL2, V_B1_RX_EN | V_B2_RX_EN); 4021 /* state machine setup */ 4022 HFC_outb(hc, A_ST_WR_STATE, a_st_wr_state | V_ST_LD_STA); 4023 udelay(6); /* wait at least 5,21us */ 4024 HFC_outb(hc, A_ST_WR_STATE, a_st_wr_state); 4025 hc->hw.r_sci_msk |= 1 << pt; 4026 /* state machine interrupts */ 4027 HFC_outb(hc, R_SCI_MSK, hc->hw.r_sci_msk); 4028 /* unset sync on port */ 4029 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 4030 hc->syncronized &= 4031 ~(1 << hc->chan[dch->slot].port); 4032 plxsd_checksync(hc, 0); 4033 } 4034 } 4035 if (debug & DEBUG_HFCMULTI_INIT) 4036 printk("%s: done\n", __func__); 4037 } 4038 4039 4040 static int 4041 open_dchannel(struct hfc_multi *hc, struct dchannel *dch, 4042 struct channel_req *rq) 4043 { 4044 int err = 0; 4045 u_long flags; 4046 4047 if (debug & DEBUG_HW_OPEN) 4048 printk(KERN_DEBUG "%s: dev(%d) open from %p\n", __func__, 4049 dch->dev.id, __builtin_return_address(0)); 4050 if (rq->protocol == ISDN_P_NONE) 4051 return -EINVAL; 4052 if ((dch->dev.D.protocol != ISDN_P_NONE) && 4053 (dch->dev.D.protocol != rq->protocol)) { 4054 if (debug & DEBUG_HFCMULTI_MODE) 4055 printk(KERN_DEBUG "%s: change protocol %x to %x\n", 4056 __func__, dch->dev.D.protocol, rq->protocol); 4057 } 4058 if ((dch->dev.D.protocol == ISDN_P_TE_S0) && 4059 (rq->protocol != ISDN_P_TE_S0)) 4060 l1_event(dch->l1, CLOSE_CHANNEL); 4061 if (dch->dev.D.protocol != rq->protocol) { 4062 if (rq->protocol == ISDN_P_TE_S0) { 4063 err = create_l1(dch, hfcm_l1callback); 4064 if (err) 4065 return err; 4066 } 4067 dch->dev.D.protocol = rq->protocol; 4068 spin_lock_irqsave(&hc->lock, flags); 4069 hfcmulti_initmode(dch); 4070 spin_unlock_irqrestore(&hc->lock, flags); 4071 } 4072 if (test_bit(FLG_ACTIVE, &dch->Flags)) 4073 _queue_data(&dch->dev.D, PH_ACTIVATE_IND, MISDN_ID_ANY, 4074 0, NULL, GFP_KERNEL); 4075 rq->ch = &dch->dev.D; 4076 if (!try_module_get(THIS_MODULE)) 4077 printk(KERN_WARNING "%s:cannot get module\n", __func__); 4078 return 0; 4079 } 4080 4081 static int 4082 open_bchannel(struct hfc_multi *hc, struct dchannel *dch, 4083 struct channel_req *rq) 4084 { 4085 struct bchannel *bch; 4086 int ch; 4087 4088 if (!test_channelmap(rq->adr.channel, dch->dev.channelmap)) 4089 return -EINVAL; 4090 if (rq->protocol == ISDN_P_NONE) 4091 return -EINVAL; 4092 if (hc->ctype == HFC_TYPE_E1) 4093 ch = rq->adr.channel; 4094 else 4095 ch = (rq->adr.channel - 1) + (dch->slot - 2); 4096 bch = hc->chan[ch].bch; 4097 if (!bch) { 4098 printk(KERN_ERR "%s:internal error ch %d has no bch\n", 4099 __func__, ch); 4100 return -EINVAL; 4101 } 4102 if (test_and_set_bit(FLG_OPEN, &bch->Flags)) 4103 return -EBUSY; /* b-channel can be only open once */ 4104 bch->ch.protocol = rq->protocol; 4105 hc->chan[ch].rx_off = 0; 4106 rq->ch = &bch->ch; 4107 if (!try_module_get(THIS_MODULE)) 4108 printk(KERN_WARNING "%s:cannot get module\n", __func__); 4109 return 0; 4110 } 4111 4112 /* 4113 * device control function 4114 */ 4115 static int 4116 channel_dctrl(struct dchannel *dch, struct mISDN_ctrl_req *cq) 4117 { 4118 struct hfc_multi *hc = dch->hw; 4119 int ret = 0; 4120 int wd_mode, wd_cnt; 4121 4122 switch (cq->op) { 4123 case MISDN_CTRL_GETOP: 4124 cq->op = MISDN_CTRL_HFC_OP | MISDN_CTRL_L1_TIMER3; 4125 break; 4126 case MISDN_CTRL_HFC_WD_INIT: /* init the watchdog */ 4127 wd_cnt = cq->p1 & 0xf; 4128 wd_mode = !!(cq->p1 >> 4); 4129 if (debug & DEBUG_HFCMULTI_MSG) 4130 printk(KERN_DEBUG "%s: MISDN_CTRL_HFC_WD_INIT mode %s" 4131 ", counter 0x%x\n", __func__, 4132 wd_mode ? "AUTO" : "MANUAL", wd_cnt); 4133 /* set the watchdog timer */ 4134 HFC_outb(hc, R_TI_WD, poll_timer | (wd_cnt << 4)); 4135 hc->hw.r_bert_wd_md = (wd_mode ? V_AUTO_WD_RES : 0); 4136 if (hc->ctype == HFC_TYPE_XHFC) 4137 hc->hw.r_bert_wd_md |= 0x40 /* V_WD_EN */; 4138 /* init the watchdog register and reset the counter */ 4139 HFC_outb(hc, R_BERT_WD_MD, hc->hw.r_bert_wd_md | V_WD_RES); 4140 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 4141 /* enable the watchdog output for Speech-Design */ 4142 HFC_outb(hc, R_GPIO_SEL, V_GPIO_SEL7); 4143 HFC_outb(hc, R_GPIO_EN1, V_GPIO_EN15); 4144 HFC_outb(hc, R_GPIO_OUT1, 0); 4145 HFC_outb(hc, R_GPIO_OUT1, V_GPIO_OUT15); 4146 } 4147 break; 4148 case MISDN_CTRL_HFC_WD_RESET: /* reset the watchdog counter */ 4149 if (debug & DEBUG_HFCMULTI_MSG) 4150 printk(KERN_DEBUG "%s: MISDN_CTRL_HFC_WD_RESET\n", 4151 __func__); 4152 HFC_outb(hc, R_BERT_WD_MD, hc->hw.r_bert_wd_md | V_WD_RES); 4153 break; 4154 case MISDN_CTRL_L1_TIMER3: 4155 ret = l1_event(dch->l1, HW_TIMER3_VALUE | (cq->p1 & 0xff)); 4156 break; 4157 default: 4158 printk(KERN_WARNING "%s: unknown Op %x\n", 4159 __func__, cq->op); 4160 ret = -EINVAL; 4161 break; 4162 } 4163 return ret; 4164 } 4165 4166 static int 4167 hfcm_dctrl(struct mISDNchannel *ch, u_int cmd, void *arg) 4168 { 4169 struct mISDNdevice *dev = container_of(ch, struct mISDNdevice, D); 4170 struct dchannel *dch = container_of(dev, struct dchannel, dev); 4171 struct hfc_multi *hc = dch->hw; 4172 struct channel_req *rq; 4173 int err = 0; 4174 u_long flags; 4175 4176 if (dch->debug & DEBUG_HW) 4177 printk(KERN_DEBUG "%s: cmd:%x %p\n", 4178 __func__, cmd, arg); 4179 switch (cmd) { 4180 case OPEN_CHANNEL: 4181 rq = arg; 4182 switch (rq->protocol) { 4183 case ISDN_P_TE_S0: 4184 case ISDN_P_NT_S0: 4185 if (hc->ctype == HFC_TYPE_E1) { 4186 err = -EINVAL; 4187 break; 4188 } 4189 err = open_dchannel(hc, dch, rq); /* locked there */ 4190 break; 4191 case ISDN_P_TE_E1: 4192 case ISDN_P_NT_E1: 4193 if (hc->ctype != HFC_TYPE_E1) { 4194 err = -EINVAL; 4195 break; 4196 } 4197 err = open_dchannel(hc, dch, rq); /* locked there */ 4198 break; 4199 default: 4200 spin_lock_irqsave(&hc->lock, flags); 4201 err = open_bchannel(hc, dch, rq); 4202 spin_unlock_irqrestore(&hc->lock, flags); 4203 } 4204 break; 4205 case CLOSE_CHANNEL: 4206 if (debug & DEBUG_HW_OPEN) 4207 printk(KERN_DEBUG "%s: dev(%d) close from %p\n", 4208 __func__, dch->dev.id, 4209 __builtin_return_address(0)); 4210 module_put(THIS_MODULE); 4211 break; 4212 case CONTROL_CHANNEL: 4213 spin_lock_irqsave(&hc->lock, flags); 4214 err = channel_dctrl(dch, arg); 4215 spin_unlock_irqrestore(&hc->lock, flags); 4216 break; 4217 default: 4218 if (dch->debug & DEBUG_HW) 4219 printk(KERN_DEBUG "%s: unknown command %x\n", 4220 __func__, cmd); 4221 err = -EINVAL; 4222 } 4223 return err; 4224 } 4225 4226 static int 4227 clockctl(void *priv, int enable) 4228 { 4229 struct hfc_multi *hc = priv; 4230 4231 hc->iclock_on = enable; 4232 return 0; 4233 } 4234 4235 /* 4236 * initialize the card 4237 */ 4238 4239 /* 4240 * start timer irq, wait some time and check if we have interrupts. 4241 * if not, reset chip and try again. 4242 */ 4243 static int 4244 init_card(struct hfc_multi *hc) 4245 { 4246 int err = -EIO; 4247 u_long flags; 4248 void __iomem *plx_acc; 4249 u_long plx_flags; 4250 4251 if (debug & DEBUG_HFCMULTI_INIT) 4252 printk(KERN_DEBUG "%s: entered\n", __func__); 4253 4254 spin_lock_irqsave(&hc->lock, flags); 4255 /* set interrupts but leave global interrupt disabled */ 4256 hc->hw.r_irq_ctrl = V_FIFO_IRQ; 4257 disable_hwirq(hc); 4258 spin_unlock_irqrestore(&hc->lock, flags); 4259 4260 if (request_irq(hc->irq, hfcmulti_interrupt, IRQF_SHARED, 4261 "HFC-multi", hc)) { 4262 printk(KERN_WARNING "mISDN: Could not get interrupt %d.\n", 4263 hc->irq); 4264 hc->irq = 0; 4265 return -EIO; 4266 } 4267 4268 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 4269 spin_lock_irqsave(&plx_lock, plx_flags); 4270 plx_acc = hc->plx_membase + PLX_INTCSR; 4271 writew((PLX_INTCSR_PCIINT_ENABLE | PLX_INTCSR_LINTI1_ENABLE), 4272 plx_acc); /* enable PCI & LINT1 irq */ 4273 spin_unlock_irqrestore(&plx_lock, plx_flags); 4274 } 4275 4276 if (debug & DEBUG_HFCMULTI_INIT) 4277 printk(KERN_DEBUG "%s: IRQ %d count %d\n", 4278 __func__, hc->irq, hc->irqcnt); 4279 err = init_chip(hc); 4280 if (err) 4281 goto error; 4282 /* 4283 * Finally enable IRQ output 4284 * this is only allowed, if an IRQ routine is already 4285 * established for this HFC, so don't do that earlier 4286 */ 4287 spin_lock_irqsave(&hc->lock, flags); 4288 enable_hwirq(hc); 4289 spin_unlock_irqrestore(&hc->lock, flags); 4290 /* printk(KERN_DEBUG "no master irq set!!!\n"); */ 4291 set_current_state(TASK_UNINTERRUPTIBLE); 4292 schedule_timeout((100 * HZ) / 1000); /* Timeout 100ms */ 4293 /* turn IRQ off until chip is completely initialized */ 4294 spin_lock_irqsave(&hc->lock, flags); 4295 disable_hwirq(hc); 4296 spin_unlock_irqrestore(&hc->lock, flags); 4297 if (debug & DEBUG_HFCMULTI_INIT) 4298 printk(KERN_DEBUG "%s: IRQ %d count %d\n", 4299 __func__, hc->irq, hc->irqcnt); 4300 if (hc->irqcnt) { 4301 if (debug & DEBUG_HFCMULTI_INIT) 4302 printk(KERN_DEBUG "%s: done\n", __func__); 4303 4304 return 0; 4305 } 4306 if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) { 4307 printk(KERN_INFO "ignoring missing interrupts\n"); 4308 return 0; 4309 } 4310 4311 printk(KERN_ERR "HFC PCI: IRQ(%d) getting no interrupts during init.\n", 4312 hc->irq); 4313 4314 err = -EIO; 4315 4316 error: 4317 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 4318 spin_lock_irqsave(&plx_lock, plx_flags); 4319 plx_acc = hc->plx_membase + PLX_INTCSR; 4320 writew(0x00, plx_acc); /*disable IRQs*/ 4321 spin_unlock_irqrestore(&plx_lock, plx_flags); 4322 } 4323 4324 if (debug & DEBUG_HFCMULTI_INIT) 4325 printk(KERN_DEBUG "%s: free irq %d\n", __func__, hc->irq); 4326 if (hc->irq) { 4327 free_irq(hc->irq, hc); 4328 hc->irq = 0; 4329 } 4330 4331 if (debug & DEBUG_HFCMULTI_INIT) 4332 printk(KERN_DEBUG "%s: done (err=%d)\n", __func__, err); 4333 return err; 4334 } 4335 4336 /* 4337 * find pci device and set it up 4338 */ 4339 4340 static int 4341 setup_pci(struct hfc_multi *hc, struct pci_dev *pdev, 4342 const struct pci_device_id *ent) 4343 { 4344 struct hm_map *m = (struct hm_map *)ent->driver_data; 4345 4346 printk(KERN_INFO 4347 "HFC-multi: card manufacturer: '%s' card name: '%s' clock: %s\n", 4348 m->vendor_name, m->card_name, m->clock2 ? "double" : "normal"); 4349 4350 hc->pci_dev = pdev; 4351 if (m->clock2) 4352 test_and_set_bit(HFC_CHIP_CLOCK2, &hc->chip); 4353 4354 if (ent->vendor == PCI_VENDOR_ID_DIGIUM && 4355 ent->device == PCI_DEVICE_ID_DIGIUM_HFC4S) { 4356 test_and_set_bit(HFC_CHIP_B410P, &hc->chip); 4357 test_and_set_bit(HFC_CHIP_PCM_MASTER, &hc->chip); 4358 test_and_clear_bit(HFC_CHIP_PCM_SLAVE, &hc->chip); 4359 hc->slots = 32; 4360 } 4361 4362 if (hc->pci_dev->irq <= 0) { 4363 printk(KERN_WARNING "HFC-multi: No IRQ for PCI card found.\n"); 4364 return -EIO; 4365 } 4366 if (pci_enable_device(hc->pci_dev)) { 4367 printk(KERN_WARNING "HFC-multi: Error enabling PCI card.\n"); 4368 return -EIO; 4369 } 4370 hc->leds = m->leds; 4371 hc->ledstate = 0xAFFEAFFE; 4372 hc->opticalsupport = m->opticalsupport; 4373 4374 hc->pci_iobase = 0; 4375 hc->pci_membase = NULL; 4376 hc->plx_membase = NULL; 4377 4378 /* set memory access methods */ 4379 if (m->io_mode) /* use mode from card config */ 4380 hc->io_mode = m->io_mode; 4381 switch (hc->io_mode) { 4382 case HFC_IO_MODE_PLXSD: 4383 test_and_set_bit(HFC_CHIP_PLXSD, &hc->chip); 4384 hc->slots = 128; /* required */ 4385 hc->HFC_outb = HFC_outb_pcimem; 4386 hc->HFC_inb = HFC_inb_pcimem; 4387 hc->HFC_inw = HFC_inw_pcimem; 4388 hc->HFC_wait = HFC_wait_pcimem; 4389 hc->read_fifo = read_fifo_pcimem; 4390 hc->write_fifo = write_fifo_pcimem; 4391 hc->plx_origmembase = hc->pci_dev->resource[0].start; 4392 /* MEMBASE 1 is PLX PCI Bridge */ 4393 4394 if (!hc->plx_origmembase) { 4395 printk(KERN_WARNING 4396 "HFC-multi: No IO-Memory for PCI PLX bridge found\n"); 4397 pci_disable_device(hc->pci_dev); 4398 return -EIO; 4399 } 4400 4401 hc->plx_membase = ioremap(hc->plx_origmembase, 0x80); 4402 if (!hc->plx_membase) { 4403 printk(KERN_WARNING 4404 "HFC-multi: failed to remap plx address space. " 4405 "(internal error)\n"); 4406 pci_disable_device(hc->pci_dev); 4407 return -EIO; 4408 } 4409 printk(KERN_INFO 4410 "HFC-multi: plx_membase:%#lx plx_origmembase:%#lx\n", 4411 (u_long)hc->plx_membase, hc->plx_origmembase); 4412 4413 hc->pci_origmembase = hc->pci_dev->resource[2].start; 4414 /* MEMBASE 1 is PLX PCI Bridge */ 4415 if (!hc->pci_origmembase) { 4416 printk(KERN_WARNING 4417 "HFC-multi: No IO-Memory for PCI card found\n"); 4418 pci_disable_device(hc->pci_dev); 4419 return -EIO; 4420 } 4421 4422 hc->pci_membase = ioremap(hc->pci_origmembase, 0x400); 4423 if (!hc->pci_membase) { 4424 printk(KERN_WARNING "HFC-multi: failed to remap io " 4425 "address space. (internal error)\n"); 4426 pci_disable_device(hc->pci_dev); 4427 return -EIO; 4428 } 4429 4430 printk(KERN_INFO 4431 "card %d: defined at MEMBASE %#lx (%#lx) IRQ %d HZ %d " 4432 "leds-type %d\n", 4433 hc->id, (u_long)hc->pci_membase, hc->pci_origmembase, 4434 hc->pci_dev->irq, HZ, hc->leds); 4435 pci_write_config_word(hc->pci_dev, PCI_COMMAND, PCI_ENA_MEMIO); 4436 break; 4437 case HFC_IO_MODE_PCIMEM: 4438 hc->HFC_outb = HFC_outb_pcimem; 4439 hc->HFC_inb = HFC_inb_pcimem; 4440 hc->HFC_inw = HFC_inw_pcimem; 4441 hc->HFC_wait = HFC_wait_pcimem; 4442 hc->read_fifo = read_fifo_pcimem; 4443 hc->write_fifo = write_fifo_pcimem; 4444 hc->pci_origmembase = hc->pci_dev->resource[1].start; 4445 if (!hc->pci_origmembase) { 4446 printk(KERN_WARNING 4447 "HFC-multi: No IO-Memory for PCI card found\n"); 4448 pci_disable_device(hc->pci_dev); 4449 return -EIO; 4450 } 4451 4452 hc->pci_membase = ioremap(hc->pci_origmembase, 256); 4453 if (!hc->pci_membase) { 4454 printk(KERN_WARNING 4455 "HFC-multi: failed to remap io address space. " 4456 "(internal error)\n"); 4457 pci_disable_device(hc->pci_dev); 4458 return -EIO; 4459 } 4460 printk(KERN_INFO "card %d: defined at MEMBASE %#lx (%#lx) IRQ " 4461 "%d HZ %d leds-type %d\n", hc->id, (u_long)hc->pci_membase, 4462 hc->pci_origmembase, hc->pci_dev->irq, HZ, hc->leds); 4463 pci_write_config_word(hc->pci_dev, PCI_COMMAND, PCI_ENA_MEMIO); 4464 break; 4465 case HFC_IO_MODE_REGIO: 4466 hc->HFC_outb = HFC_outb_regio; 4467 hc->HFC_inb = HFC_inb_regio; 4468 hc->HFC_inw = HFC_inw_regio; 4469 hc->HFC_wait = HFC_wait_regio; 4470 hc->read_fifo = read_fifo_regio; 4471 hc->write_fifo = write_fifo_regio; 4472 hc->pci_iobase = (u_int) hc->pci_dev->resource[0].start; 4473 if (!hc->pci_iobase) { 4474 printk(KERN_WARNING 4475 "HFC-multi: No IO for PCI card found\n"); 4476 pci_disable_device(hc->pci_dev); 4477 return -EIO; 4478 } 4479 4480 if (!request_region(hc->pci_iobase, 8, "hfcmulti")) { 4481 printk(KERN_WARNING "HFC-multi: failed to request " 4482 "address space at 0x%08lx (internal error)\n", 4483 hc->pci_iobase); 4484 pci_disable_device(hc->pci_dev); 4485 return -EIO; 4486 } 4487 4488 printk(KERN_INFO 4489 "%s %s: defined at IOBASE %#x IRQ %d HZ %d leds-type %d\n", 4490 m->vendor_name, m->card_name, (u_int) hc->pci_iobase, 4491 hc->pci_dev->irq, HZ, hc->leds); 4492 pci_write_config_word(hc->pci_dev, PCI_COMMAND, PCI_ENA_REGIO); 4493 break; 4494 default: 4495 printk(KERN_WARNING "HFC-multi: Invalid IO mode.\n"); 4496 pci_disable_device(hc->pci_dev); 4497 return -EIO; 4498 } 4499 4500 pci_set_drvdata(hc->pci_dev, hc); 4501 4502 /* At this point the needed PCI config is done */ 4503 /* fifos are still not enabled */ 4504 return 0; 4505 } 4506 4507 4508 /* 4509 * remove port 4510 */ 4511 4512 static void 4513 release_port(struct hfc_multi *hc, struct dchannel *dch) 4514 { 4515 int pt, ci, i = 0; 4516 u_long flags; 4517 struct bchannel *pb; 4518 4519 ci = dch->slot; 4520 pt = hc->chan[ci].port; 4521 4522 if (debug & DEBUG_HFCMULTI_INIT) 4523 printk(KERN_DEBUG "%s: entered for port %d\n", 4524 __func__, pt + 1); 4525 4526 if (pt >= hc->ports) { 4527 printk(KERN_WARNING "%s: ERROR port out of range (%d).\n", 4528 __func__, pt + 1); 4529 return; 4530 } 4531 4532 if (debug & DEBUG_HFCMULTI_INIT) 4533 printk(KERN_DEBUG "%s: releasing port=%d\n", 4534 __func__, pt + 1); 4535 4536 if (dch->dev.D.protocol == ISDN_P_TE_S0) 4537 l1_event(dch->l1, CLOSE_CHANNEL); 4538 4539 hc->chan[ci].dch = NULL; 4540 4541 if (hc->created[pt]) { 4542 hc->created[pt] = 0; 4543 mISDN_unregister_device(&dch->dev); 4544 } 4545 4546 spin_lock_irqsave(&hc->lock, flags); 4547 4548 if (dch->timer.function) { 4549 del_timer(&dch->timer); 4550 dch->timer.function = NULL; 4551 } 4552 4553 if (hc->ctype == HFC_TYPE_E1) { /* E1 */ 4554 /* remove sync */ 4555 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 4556 hc->syncronized = 0; 4557 plxsd_checksync(hc, 1); 4558 } 4559 /* free channels */ 4560 for (i = 0; i <= 31; i++) { 4561 if (!((1 << i) & hc->bmask[pt])) /* skip unused chan */ 4562 continue; 4563 if (hc->chan[i].bch) { 4564 if (debug & DEBUG_HFCMULTI_INIT) 4565 printk(KERN_DEBUG 4566 "%s: free port %d channel %d\n", 4567 __func__, hc->chan[i].port + 1, i); 4568 pb = hc->chan[i].bch; 4569 hc->chan[i].bch = NULL; 4570 spin_unlock_irqrestore(&hc->lock, flags); 4571 mISDN_freebchannel(pb); 4572 kfree(pb); 4573 kfree(hc->chan[i].coeff); 4574 spin_lock_irqsave(&hc->lock, flags); 4575 } 4576 } 4577 } else { 4578 /* remove sync */ 4579 if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) { 4580 hc->syncronized &= 4581 ~(1 << hc->chan[ci].port); 4582 plxsd_checksync(hc, 1); 4583 } 4584 /* free channels */ 4585 if (hc->chan[ci - 2].bch) { 4586 if (debug & DEBUG_HFCMULTI_INIT) 4587 printk(KERN_DEBUG 4588 "%s: free port %d channel %d\n", 4589 __func__, hc->chan[ci - 2].port + 1, 4590 ci - 2); 4591 pb = hc->chan[ci - 2].bch; 4592 hc->chan[ci - 2].bch = NULL; 4593 spin_unlock_irqrestore(&hc->lock, flags); 4594 mISDN_freebchannel(pb); 4595 kfree(pb); 4596 kfree(hc->chan[ci - 2].coeff); 4597 spin_lock_irqsave(&hc->lock, flags); 4598 } 4599 if (hc->chan[ci - 1].bch) { 4600 if (debug & DEBUG_HFCMULTI_INIT) 4601 printk(KERN_DEBUG 4602 "%s: free port %d channel %d\n", 4603 __func__, hc->chan[ci - 1].port + 1, 4604 ci - 1); 4605 pb = hc->chan[ci - 1].bch; 4606 hc->chan[ci - 1].bch = NULL; 4607 spin_unlock_irqrestore(&hc->lock, flags); 4608 mISDN_freebchannel(pb); 4609 kfree(pb); 4610 kfree(hc->chan[ci - 1].coeff); 4611 spin_lock_irqsave(&hc->lock, flags); 4612 } 4613 } 4614 4615 spin_unlock_irqrestore(&hc->lock, flags); 4616 4617 if (debug & DEBUG_HFCMULTI_INIT) 4618 printk(KERN_DEBUG "%s: free port %d channel D(%d)\n", __func__, 4619 pt+1, ci); 4620 mISDN_freedchannel(dch); 4621 kfree(dch); 4622 4623 if (debug & DEBUG_HFCMULTI_INIT) 4624 printk(KERN_DEBUG "%s: done!\n", __func__); 4625 } 4626 4627 static void 4628 release_card(struct hfc_multi *hc) 4629 { 4630 u_long flags; 4631 int ch; 4632 4633 if (debug & DEBUG_HFCMULTI_INIT) 4634 printk(KERN_DEBUG "%s: release card (%d) entered\n", 4635 __func__, hc->id); 4636 4637 /* unregister clock source */ 4638 if (hc->iclock) 4639 mISDN_unregister_clock(hc->iclock); 4640 4641 /* disable and free irq */ 4642 spin_lock_irqsave(&hc->lock, flags); 4643 disable_hwirq(hc); 4644 spin_unlock_irqrestore(&hc->lock, flags); 4645 udelay(1000); 4646 if (hc->irq) { 4647 if (debug & DEBUG_HFCMULTI_INIT) 4648 printk(KERN_DEBUG "%s: free irq %d (hc=%p)\n", 4649 __func__, hc->irq, hc); 4650 free_irq(hc->irq, hc); 4651 hc->irq = 0; 4652 4653 } 4654 4655 /* disable D-channels & B-channels */ 4656 if (debug & DEBUG_HFCMULTI_INIT) 4657 printk(KERN_DEBUG "%s: disable all channels (d and b)\n", 4658 __func__); 4659 for (ch = 0; ch <= 31; ch++) { 4660 if (hc->chan[ch].dch) 4661 release_port(hc, hc->chan[ch].dch); 4662 } 4663 4664 /* dimm leds */ 4665 if (hc->leds) 4666 hfcmulti_leds(hc); 4667 4668 /* release hardware */ 4669 release_io_hfcmulti(hc); 4670 4671 if (debug & DEBUG_HFCMULTI_INIT) 4672 printk(KERN_DEBUG "%s: remove instance from list\n", 4673 __func__); 4674 list_del(&hc->list); 4675 4676 if (debug & DEBUG_HFCMULTI_INIT) 4677 printk(KERN_DEBUG "%s: delete instance\n", __func__); 4678 if (hc == syncmaster) 4679 syncmaster = NULL; 4680 kfree(hc); 4681 if (debug & DEBUG_HFCMULTI_INIT) 4682 printk(KERN_DEBUG "%s: card successfully removed\n", 4683 __func__); 4684 } 4685 4686 static void 4687 init_e1_port_hw(struct hfc_multi *hc, struct hm_map *m) 4688 { 4689 /* set optical line type */ 4690 if (port[Port_cnt] & 0x001) { 4691 if (!m->opticalsupport) { 4692 printk(KERN_INFO 4693 "This board has no optical " 4694 "support\n"); 4695 } else { 4696 if (debug & DEBUG_HFCMULTI_INIT) 4697 printk(KERN_DEBUG 4698 "%s: PORT set optical " 4699 "interfacs: card(%d) " 4700 "port(%d)\n", 4701 __func__, 4702 HFC_cnt + 1, 1); 4703 test_and_set_bit(HFC_CFG_OPTICAL, 4704 &hc->chan[hc->dnum[0]].cfg); 4705 } 4706 } 4707 /* set LOS report */ 4708 if (port[Port_cnt] & 0x004) { 4709 if (debug & DEBUG_HFCMULTI_INIT) 4710 printk(KERN_DEBUG "%s: PORT set " 4711 "LOS report: card(%d) port(%d)\n", 4712 __func__, HFC_cnt + 1, 1); 4713 test_and_set_bit(HFC_CFG_REPORT_LOS, 4714 &hc->chan[hc->dnum[0]].cfg); 4715 } 4716 /* set AIS report */ 4717 if (port[Port_cnt] & 0x008) { 4718 if (debug & DEBUG_HFCMULTI_INIT) 4719 printk(KERN_DEBUG "%s: PORT set " 4720 "AIS report: card(%d) port(%d)\n", 4721 __func__, HFC_cnt + 1, 1); 4722 test_and_set_bit(HFC_CFG_REPORT_AIS, 4723 &hc->chan[hc->dnum[0]].cfg); 4724 } 4725 /* set SLIP report */ 4726 if (port[Port_cnt] & 0x010) { 4727 if (debug & DEBUG_HFCMULTI_INIT) 4728 printk(KERN_DEBUG 4729 "%s: PORT set SLIP report: " 4730 "card(%d) port(%d)\n", 4731 __func__, HFC_cnt + 1, 1); 4732 test_and_set_bit(HFC_CFG_REPORT_SLIP, 4733 &hc->chan[hc->dnum[0]].cfg); 4734 } 4735 /* set RDI report */ 4736 if (port[Port_cnt] & 0x020) { 4737 if (debug & DEBUG_HFCMULTI_INIT) 4738 printk(KERN_DEBUG 4739 "%s: PORT set RDI report: " 4740 "card(%d) port(%d)\n", 4741 __func__, HFC_cnt + 1, 1); 4742 test_and_set_bit(HFC_CFG_REPORT_RDI, 4743 &hc->chan[hc->dnum[0]].cfg); 4744 } 4745 /* set CRC-4 Mode */ 4746 if (!(port[Port_cnt] & 0x100)) { 4747 if (debug & DEBUG_HFCMULTI_INIT) 4748 printk(KERN_DEBUG "%s: PORT turn on CRC4 report:" 4749 " card(%d) port(%d)\n", 4750 __func__, HFC_cnt + 1, 1); 4751 test_and_set_bit(HFC_CFG_CRC4, 4752 &hc->chan[hc->dnum[0]].cfg); 4753 } else { 4754 if (debug & DEBUG_HFCMULTI_INIT) 4755 printk(KERN_DEBUG "%s: PORT turn off CRC4" 4756 " report: card(%d) port(%d)\n", 4757 __func__, HFC_cnt + 1, 1); 4758 } 4759 /* set forced clock */ 4760 if (port[Port_cnt] & 0x0200) { 4761 if (debug & DEBUG_HFCMULTI_INIT) 4762 printk(KERN_DEBUG "%s: PORT force getting clock from " 4763 "E1: card(%d) port(%d)\n", 4764 __func__, HFC_cnt + 1, 1); 4765 test_and_set_bit(HFC_CHIP_E1CLOCK_GET, &hc->chip); 4766 } else 4767 if (port[Port_cnt] & 0x0400) { 4768 if (debug & DEBUG_HFCMULTI_INIT) 4769 printk(KERN_DEBUG "%s: PORT force putting clock to " 4770 "E1: card(%d) port(%d)\n", 4771 __func__, HFC_cnt + 1, 1); 4772 test_and_set_bit(HFC_CHIP_E1CLOCK_PUT, &hc->chip); 4773 } 4774 /* set JATT PLL */ 4775 if (port[Port_cnt] & 0x0800) { 4776 if (debug & DEBUG_HFCMULTI_INIT) 4777 printk(KERN_DEBUG "%s: PORT disable JATT PLL on " 4778 "E1: card(%d) port(%d)\n", 4779 __func__, HFC_cnt + 1, 1); 4780 test_and_set_bit(HFC_CHIP_RX_SYNC, &hc->chip); 4781 } 4782 /* set elastic jitter buffer */ 4783 if (port[Port_cnt] & 0x3000) { 4784 hc->chan[hc->dnum[0]].jitter = (port[Port_cnt]>>12) & 0x3; 4785 if (debug & DEBUG_HFCMULTI_INIT) 4786 printk(KERN_DEBUG 4787 "%s: PORT set elastic " 4788 "buffer to %d: card(%d) port(%d)\n", 4789 __func__, hc->chan[hc->dnum[0]].jitter, 4790 HFC_cnt + 1, 1); 4791 } else 4792 hc->chan[hc->dnum[0]].jitter = 2; /* default */ 4793 } 4794 4795 static int 4796 init_e1_port(struct hfc_multi *hc, struct hm_map *m, int pt) 4797 { 4798 struct dchannel *dch; 4799 struct bchannel *bch; 4800 int ch, ret = 0; 4801 char name[MISDN_MAX_IDLEN]; 4802 int bcount = 0; 4803 4804 dch = kzalloc(sizeof(struct dchannel), GFP_KERNEL); 4805 if (!dch) 4806 return -ENOMEM; 4807 dch->debug = debug; 4808 mISDN_initdchannel(dch, MAX_DFRAME_LEN_L1, ph_state_change); 4809 dch->hw = hc; 4810 dch->dev.Dprotocols = (1 << ISDN_P_TE_E1) | (1 << ISDN_P_NT_E1); 4811 dch->dev.Bprotocols = (1 << (ISDN_P_B_RAW & ISDN_P_B_MASK)) | 4812 (1 << (ISDN_P_B_HDLC & ISDN_P_B_MASK)); 4813 dch->dev.D.send = handle_dmsg; 4814 dch->dev.D.ctrl = hfcm_dctrl; 4815 dch->slot = hc->dnum[pt]; 4816 hc->chan[hc->dnum[pt]].dch = dch; 4817 hc->chan[hc->dnum[pt]].port = pt; 4818 hc->chan[hc->dnum[pt]].nt_timer = -1; 4819 for (ch = 1; ch <= 31; ch++) { 4820 if (!((1 << ch) & hc->bmask[pt])) /* skip unused channel */ 4821 continue; 4822 bch = kzalloc(sizeof(struct bchannel), GFP_KERNEL); 4823 if (!bch) { 4824 printk(KERN_ERR "%s: no memory for bchannel\n", 4825 __func__); 4826 ret = -ENOMEM; 4827 goto free_chan; 4828 } 4829 hc->chan[ch].coeff = kzalloc(512, GFP_KERNEL); 4830 if (!hc->chan[ch].coeff) { 4831 printk(KERN_ERR "%s: no memory for coeffs\n", 4832 __func__); 4833 ret = -ENOMEM; 4834 kfree(bch); 4835 goto free_chan; 4836 } 4837 bch->nr = ch; 4838 bch->slot = ch; 4839 bch->debug = debug; 4840 mISDN_initbchannel(bch, MAX_DATA_MEM, poll >> 1); 4841 bch->hw = hc; 4842 bch->ch.send = handle_bmsg; 4843 bch->ch.ctrl = hfcm_bctrl; 4844 bch->ch.nr = ch; 4845 list_add(&bch->ch.list, &dch->dev.bchannels); 4846 hc->chan[ch].bch = bch; 4847 hc->chan[ch].port = pt; 4848 set_channelmap(bch->nr, dch->dev.channelmap); 4849 bcount++; 4850 } 4851 dch->dev.nrbchan = bcount; 4852 if (pt == 0) 4853 init_e1_port_hw(hc, m); 4854 if (hc->ports > 1) 4855 snprintf(name, MISDN_MAX_IDLEN - 1, "hfc-e1.%d-%d", 4856 HFC_cnt + 1, pt+1); 4857 else 4858 snprintf(name, MISDN_MAX_IDLEN - 1, "hfc-e1.%d", HFC_cnt + 1); 4859 ret = mISDN_register_device(&dch->dev, &hc->pci_dev->dev, name); 4860 if (ret) 4861 goto free_chan; 4862 hc->created[pt] = 1; 4863 return ret; 4864 free_chan: 4865 release_port(hc, dch); 4866 return ret; 4867 } 4868 4869 static int 4870 init_multi_port(struct hfc_multi *hc, int pt) 4871 { 4872 struct dchannel *dch; 4873 struct bchannel *bch; 4874 int ch, i, ret = 0; 4875 char name[MISDN_MAX_IDLEN]; 4876 4877 dch = kzalloc(sizeof(struct dchannel), GFP_KERNEL); 4878 if (!dch) 4879 return -ENOMEM; 4880 dch->debug = debug; 4881 mISDN_initdchannel(dch, MAX_DFRAME_LEN_L1, ph_state_change); 4882 dch->hw = hc; 4883 dch->dev.Dprotocols = (1 << ISDN_P_TE_S0) | (1 << ISDN_P_NT_S0); 4884 dch->dev.Bprotocols = (1 << (ISDN_P_B_RAW & ISDN_P_B_MASK)) | 4885 (1 << (ISDN_P_B_HDLC & ISDN_P_B_MASK)); 4886 dch->dev.D.send = handle_dmsg; 4887 dch->dev.D.ctrl = hfcm_dctrl; 4888 dch->dev.nrbchan = 2; 4889 i = pt << 2; 4890 dch->slot = i + 2; 4891 hc->chan[i + 2].dch = dch; 4892 hc->chan[i + 2].port = pt; 4893 hc->chan[i + 2].nt_timer = -1; 4894 for (ch = 0; ch < dch->dev.nrbchan; ch++) { 4895 bch = kzalloc(sizeof(struct bchannel), GFP_KERNEL); 4896 if (!bch) { 4897 printk(KERN_ERR "%s: no memory for bchannel\n", 4898 __func__); 4899 ret = -ENOMEM; 4900 goto free_chan; 4901 } 4902 hc->chan[i + ch].coeff = kzalloc(512, GFP_KERNEL); 4903 if (!hc->chan[i + ch].coeff) { 4904 printk(KERN_ERR "%s: no memory for coeffs\n", 4905 __func__); 4906 ret = -ENOMEM; 4907 kfree(bch); 4908 goto free_chan; 4909 } 4910 bch->nr = ch + 1; 4911 bch->slot = i + ch; 4912 bch->debug = debug; 4913 mISDN_initbchannel(bch, MAX_DATA_MEM, poll >> 1); 4914 bch->hw = hc; 4915 bch->ch.send = handle_bmsg; 4916 bch->ch.ctrl = hfcm_bctrl; 4917 bch->ch.nr = ch + 1; 4918 list_add(&bch->ch.list, &dch->dev.bchannels); 4919 hc->chan[i + ch].bch = bch; 4920 hc->chan[i + ch].port = pt; 4921 set_channelmap(bch->nr, dch->dev.channelmap); 4922 } 4923 /* set master clock */ 4924 if (port[Port_cnt] & 0x001) { 4925 if (debug & DEBUG_HFCMULTI_INIT) 4926 printk(KERN_DEBUG 4927 "%s: PROTOCOL set master clock: " 4928 "card(%d) port(%d)\n", 4929 __func__, HFC_cnt + 1, pt + 1); 4930 if (dch->dev.D.protocol != ISDN_P_TE_S0) { 4931 printk(KERN_ERR "Error: Master clock " 4932 "for port(%d) of card(%d) is only" 4933 " possible with TE-mode\n", 4934 pt + 1, HFC_cnt + 1); 4935 ret = -EINVAL; 4936 goto free_chan; 4937 } 4938 if (hc->masterclk >= 0) { 4939 printk(KERN_ERR "Error: Master clock " 4940 "for port(%d) of card(%d) already " 4941 "defined for port(%d)\n", 4942 pt + 1, HFC_cnt + 1, hc->masterclk + 1); 4943 ret = -EINVAL; 4944 goto free_chan; 4945 } 4946 hc->masterclk = pt; 4947 } 4948 /* set transmitter line to non capacitive */ 4949 if (port[Port_cnt] & 0x002) { 4950 if (debug & DEBUG_HFCMULTI_INIT) 4951 printk(KERN_DEBUG 4952 "%s: PROTOCOL set non capacitive " 4953 "transmitter: card(%d) port(%d)\n", 4954 __func__, HFC_cnt + 1, pt + 1); 4955 test_and_set_bit(HFC_CFG_NONCAP_TX, 4956 &hc->chan[i + 2].cfg); 4957 } 4958 /* disable E-channel */ 4959 if (port[Port_cnt] & 0x004) { 4960 if (debug & DEBUG_HFCMULTI_INIT) 4961 printk(KERN_DEBUG 4962 "%s: PROTOCOL disable E-channel: " 4963 "card(%d) port(%d)\n", 4964 __func__, HFC_cnt + 1, pt + 1); 4965 test_and_set_bit(HFC_CFG_DIS_ECHANNEL, 4966 &hc->chan[i + 2].cfg); 4967 } 4968 if (hc->ctype == HFC_TYPE_XHFC) { 4969 snprintf(name, MISDN_MAX_IDLEN - 1, "xhfc.%d-%d", 4970 HFC_cnt + 1, pt + 1); 4971 ret = mISDN_register_device(&dch->dev, NULL, name); 4972 } else { 4973 snprintf(name, MISDN_MAX_IDLEN - 1, "hfc-%ds.%d-%d", 4974 hc->ctype, HFC_cnt + 1, pt + 1); 4975 ret = mISDN_register_device(&dch->dev, &hc->pci_dev->dev, name); 4976 } 4977 if (ret) 4978 goto free_chan; 4979 hc->created[pt] = 1; 4980 return ret; 4981 free_chan: 4982 release_port(hc, dch); 4983 return ret; 4984 } 4985 4986 static int 4987 hfcmulti_init(struct hm_map *m, struct pci_dev *pdev, 4988 const struct pci_device_id *ent) 4989 { 4990 int ret_err = 0; 4991 int pt; 4992 struct hfc_multi *hc; 4993 u_long flags; 4994 u_char dips = 0, pmj = 0; /* dip settings, port mode Jumpers */ 4995 int i, ch; 4996 u_int maskcheck; 4997 4998 if (HFC_cnt >= MAX_CARDS) { 4999 printk(KERN_ERR "too many cards (max=%d).\n", 5000 MAX_CARDS); 5001 return -EINVAL; 5002 } 5003 if ((type[HFC_cnt] & 0xff) && (type[HFC_cnt] & 0xff) != m->type) { 5004 printk(KERN_WARNING "HFC-MULTI: Card '%s:%s' type %d found but " 5005 "type[%d] %d was supplied as module parameter\n", 5006 m->vendor_name, m->card_name, m->type, HFC_cnt, 5007 type[HFC_cnt] & 0xff); 5008 printk(KERN_WARNING "HFC-MULTI: Load module without parameters " 5009 "first, to see cards and their types."); 5010 return -EINVAL; 5011 } 5012 if (debug & DEBUG_HFCMULTI_INIT) 5013 printk(KERN_DEBUG "%s: Registering %s:%s chip type %d (0x%x)\n", 5014 __func__, m->vendor_name, m->card_name, m->type, 5015 type[HFC_cnt]); 5016 5017 /* allocate card+fifo structure */ 5018 hc = kzalloc(sizeof(struct hfc_multi), GFP_KERNEL); 5019 if (!hc) { 5020 printk(KERN_ERR "No kmem for HFC-Multi card\n"); 5021 return -ENOMEM; 5022 } 5023 spin_lock_init(&hc->lock); 5024 hc->mtyp = m; 5025 hc->ctype = m->type; 5026 hc->ports = m->ports; 5027 hc->id = HFC_cnt; 5028 hc->pcm = pcm[HFC_cnt]; 5029 hc->io_mode = iomode[HFC_cnt]; 5030 if (hc->ctype == HFC_TYPE_E1 && dmask[E1_cnt]) { 5031 /* fragment card */ 5032 pt = 0; 5033 maskcheck = 0; 5034 for (ch = 0; ch <= 31; ch++) { 5035 if (!((1 << ch) & dmask[E1_cnt])) 5036 continue; 5037 hc->dnum[pt] = ch; 5038 hc->bmask[pt] = bmask[bmask_cnt++]; 5039 if ((maskcheck & hc->bmask[pt]) 5040 || (dmask[E1_cnt] & hc->bmask[pt])) { 5041 printk(KERN_INFO 5042 "HFC-E1 #%d has overlapping B-channels on fragment #%d\n", 5043 E1_cnt + 1, pt); 5044 kfree(hc); 5045 return -EINVAL; 5046 } 5047 maskcheck |= hc->bmask[pt]; 5048 printk(KERN_INFO 5049 "HFC-E1 #%d uses D-channel on slot %d and a B-channel map of 0x%08x\n", 5050 E1_cnt + 1, ch, hc->bmask[pt]); 5051 pt++; 5052 } 5053 hc->ports = pt; 5054 } 5055 if (hc->ctype == HFC_TYPE_E1 && !dmask[E1_cnt]) { 5056 /* default card layout */ 5057 hc->dnum[0] = 16; 5058 hc->bmask[0] = 0xfffefffe; 5059 hc->ports = 1; 5060 } 5061 5062 /* set chip specific features */ 5063 hc->masterclk = -1; 5064 if (type[HFC_cnt] & 0x100) { 5065 test_and_set_bit(HFC_CHIP_ULAW, &hc->chip); 5066 hc->silence = 0xff; /* ulaw silence */ 5067 } else 5068 hc->silence = 0x2a; /* alaw silence */ 5069 if ((poll >> 1) > sizeof(hc->silence_data)) { 5070 printk(KERN_ERR "HFCMULTI error: silence_data too small, " 5071 "please fix\n"); 5072 kfree(hc); 5073 return -EINVAL; 5074 } 5075 for (i = 0; i < (poll >> 1); i++) 5076 hc->silence_data[i] = hc->silence; 5077 5078 if (hc->ctype != HFC_TYPE_XHFC) { 5079 if (!(type[HFC_cnt] & 0x200)) 5080 test_and_set_bit(HFC_CHIP_DTMF, &hc->chip); 5081 test_and_set_bit(HFC_CHIP_CONF, &hc->chip); 5082 } 5083 5084 if (type[HFC_cnt] & 0x800) 5085 test_and_set_bit(HFC_CHIP_PCM_SLAVE, &hc->chip); 5086 if (type[HFC_cnt] & 0x1000) { 5087 test_and_set_bit(HFC_CHIP_PCM_MASTER, &hc->chip); 5088 test_and_clear_bit(HFC_CHIP_PCM_SLAVE, &hc->chip); 5089 } 5090 if (type[HFC_cnt] & 0x4000) 5091 test_and_set_bit(HFC_CHIP_EXRAM_128, &hc->chip); 5092 if (type[HFC_cnt] & 0x8000) 5093 test_and_set_bit(HFC_CHIP_EXRAM_512, &hc->chip); 5094 hc->slots = 32; 5095 if (type[HFC_cnt] & 0x10000) 5096 hc->slots = 64; 5097 if (type[HFC_cnt] & 0x20000) 5098 hc->slots = 128; 5099 if (type[HFC_cnt] & 0x80000) { 5100 test_and_set_bit(HFC_CHIP_WATCHDOG, &hc->chip); 5101 hc->wdcount = 0; 5102 hc->wdbyte = V_GPIO_OUT2; 5103 printk(KERN_NOTICE "Watchdog enabled\n"); 5104 } 5105 5106 if (pdev && ent) 5107 /* setup pci, hc->slots may change due to PLXSD */ 5108 ret_err = setup_pci(hc, pdev, ent); 5109 else 5110 #ifdef CONFIG_MISDN_HFCMULTI_8xx 5111 ret_err = setup_embedded(hc, m); 5112 #else 5113 { 5114 printk(KERN_WARNING "Embedded IO Mode not selected\n"); 5115 ret_err = -EIO; 5116 } 5117 #endif 5118 if (ret_err) { 5119 if (hc == syncmaster) 5120 syncmaster = NULL; 5121 kfree(hc); 5122 return ret_err; 5123 } 5124 5125 hc->HFC_outb_nodebug = hc->HFC_outb; 5126 hc->HFC_inb_nodebug = hc->HFC_inb; 5127 hc->HFC_inw_nodebug = hc->HFC_inw; 5128 hc->HFC_wait_nodebug = hc->HFC_wait; 5129 #ifdef HFC_REGISTER_DEBUG 5130 hc->HFC_outb = HFC_outb_debug; 5131 hc->HFC_inb = HFC_inb_debug; 5132 hc->HFC_inw = HFC_inw_debug; 5133 hc->HFC_wait = HFC_wait_debug; 5134 #endif 5135 /* create channels */ 5136 for (pt = 0; pt < hc->ports; pt++) { 5137 if (Port_cnt >= MAX_PORTS) { 5138 printk(KERN_ERR "too many ports (max=%d).\n", 5139 MAX_PORTS); 5140 ret_err = -EINVAL; 5141 goto free_card; 5142 } 5143 if (hc->ctype == HFC_TYPE_E1) 5144 ret_err = init_e1_port(hc, m, pt); 5145 else 5146 ret_err = init_multi_port(hc, pt); 5147 if (debug & DEBUG_HFCMULTI_INIT) 5148 printk(KERN_DEBUG 5149 "%s: Registering D-channel, card(%d) port(%d) " 5150 "result %d\n", 5151 __func__, HFC_cnt + 1, pt + 1, ret_err); 5152 5153 if (ret_err) { 5154 while (pt) { /* release already registered ports */ 5155 pt--; 5156 if (hc->ctype == HFC_TYPE_E1) 5157 release_port(hc, 5158 hc->chan[hc->dnum[pt]].dch); 5159 else 5160 release_port(hc, 5161 hc->chan[(pt << 2) + 2].dch); 5162 } 5163 goto free_card; 5164 } 5165 if (hc->ctype != HFC_TYPE_E1) 5166 Port_cnt++; /* for each S0 port */ 5167 } 5168 if (hc->ctype == HFC_TYPE_E1) { 5169 Port_cnt++; /* for each E1 port */ 5170 E1_cnt++; 5171 } 5172 5173 /* disp switches */ 5174 switch (m->dip_type) { 5175 case DIP_4S: 5176 /* 5177 * Get DIP setting for beroNet 1S/2S/4S cards 5178 * DIP Setting: (collect GPIO 13/14/15 (R_GPIO_IN1) + 5179 * GPI 19/23 (R_GPI_IN2)) 5180 */ 5181 dips = ((~HFC_inb(hc, R_GPIO_IN1) & 0xE0) >> 5) | 5182 ((~HFC_inb(hc, R_GPI_IN2) & 0x80) >> 3) | 5183 (~HFC_inb(hc, R_GPI_IN2) & 0x08); 5184 5185 /* Port mode (TE/NT) jumpers */ 5186 pmj = ((HFC_inb(hc, R_GPI_IN3) >> 4) & 0xf); 5187 5188 if (test_bit(HFC_CHIP_B410P, &hc->chip)) 5189 pmj = ~pmj & 0xf; 5190 5191 printk(KERN_INFO "%s: %s DIPs(0x%x) jumpers(0x%x)\n", 5192 m->vendor_name, m->card_name, dips, pmj); 5193 break; 5194 case DIP_8S: 5195 /* 5196 * Get DIP Setting for beroNet 8S0+ cards 5197 * Enable PCI auxbridge function 5198 */ 5199 HFC_outb(hc, R_BRG_PCM_CFG, 1 | V_PCM_CLK); 5200 /* prepare access to auxport */ 5201 outw(0x4000, hc->pci_iobase + 4); 5202 /* 5203 * some dummy reads are required to 5204 * read valid DIP switch data 5205 */ 5206 dips = inb(hc->pci_iobase); 5207 dips = inb(hc->pci_iobase); 5208 dips = inb(hc->pci_iobase); 5209 dips = ~inb(hc->pci_iobase) & 0x3F; 5210 outw(0x0, hc->pci_iobase + 4); 5211 /* disable PCI auxbridge function */ 5212 HFC_outb(hc, R_BRG_PCM_CFG, V_PCM_CLK); 5213 printk(KERN_INFO "%s: %s DIPs(0x%x)\n", 5214 m->vendor_name, m->card_name, dips); 5215 break; 5216 case DIP_E1: 5217 /* 5218 * get DIP Setting for beroNet E1 cards 5219 * DIP Setting: collect GPI 4/5/6/7 (R_GPI_IN0) 5220 */ 5221 dips = (~HFC_inb(hc, R_GPI_IN0) & 0xF0) >> 4; 5222 printk(KERN_INFO "%s: %s DIPs(0x%x)\n", 5223 m->vendor_name, m->card_name, dips); 5224 break; 5225 } 5226 5227 /* add to list */ 5228 spin_lock_irqsave(&HFClock, flags); 5229 list_add_tail(&hc->list, &HFClist); 5230 spin_unlock_irqrestore(&HFClock, flags); 5231 5232 /* use as clock source */ 5233 if (clock == HFC_cnt + 1) 5234 hc->iclock = mISDN_register_clock("HFCMulti", 0, clockctl, hc); 5235 5236 /* initialize hardware */ 5237 hc->irq = (m->irq) ? : hc->pci_dev->irq; 5238 ret_err = init_card(hc); 5239 if (ret_err) { 5240 printk(KERN_ERR "init card returns %d\n", ret_err); 5241 release_card(hc); 5242 return ret_err; 5243 } 5244 5245 /* start IRQ and return */ 5246 spin_lock_irqsave(&hc->lock, flags); 5247 enable_hwirq(hc); 5248 spin_unlock_irqrestore(&hc->lock, flags); 5249 return 0; 5250 5251 free_card: 5252 release_io_hfcmulti(hc); 5253 if (hc == syncmaster) 5254 syncmaster = NULL; 5255 kfree(hc); 5256 return ret_err; 5257 } 5258 5259 static void hfc_remove_pci(struct pci_dev *pdev) 5260 { 5261 struct hfc_multi *card = pci_get_drvdata(pdev); 5262 u_long flags; 5263 5264 if (debug) 5265 printk(KERN_INFO "removing hfc_multi card vendor:%x " 5266 "device:%x subvendor:%x subdevice:%x\n", 5267 pdev->vendor, pdev->device, 5268 pdev->subsystem_vendor, pdev->subsystem_device); 5269 5270 if (card) { 5271 spin_lock_irqsave(&HFClock, flags); 5272 release_card(card); 5273 spin_unlock_irqrestore(&HFClock, flags); 5274 } else { 5275 if (debug) 5276 printk(KERN_DEBUG "%s: drvdata already removed\n", 5277 __func__); 5278 } 5279 } 5280 5281 #define VENDOR_CCD "Cologne Chip AG" 5282 #define VENDOR_BN "beroNet GmbH" 5283 #define VENDOR_DIG "Digium Inc." 5284 #define VENDOR_JH "Junghanns.NET GmbH" 5285 #define VENDOR_PRIM "PrimuX" 5286 5287 static const struct hm_map hfcm_map[] = { 5288 /*0*/ {VENDOR_BN, "HFC-1S Card (mini PCI)", 4, 1, 1, 3, 0, DIP_4S, 0, 0}, 5289 /*1*/ {VENDOR_BN, "HFC-2S Card", 4, 2, 1, 3, 0, DIP_4S, 0, 0}, 5290 /*2*/ {VENDOR_BN, "HFC-2S Card (mini PCI)", 4, 2, 1, 3, 0, DIP_4S, 0, 0}, 5291 /*3*/ {VENDOR_BN, "HFC-4S Card", 4, 4, 1, 2, 0, DIP_4S, 0, 0}, 5292 /*4*/ {VENDOR_BN, "HFC-4S Card (mini PCI)", 4, 4, 1, 2, 0, 0, 0, 0}, 5293 /*5*/ {VENDOR_CCD, "HFC-4S Eval (old)", 4, 4, 0, 0, 0, 0, 0, 0}, 5294 /*6*/ {VENDOR_CCD, "HFC-4S IOB4ST", 4, 4, 1, 2, 0, DIP_4S, 0, 0}, 5295 /*7*/ {VENDOR_CCD, "HFC-4S", 4, 4, 1, 2, 0, 0, 0, 0}, 5296 /*8*/ {VENDOR_DIG, "HFC-4S Card", 4, 4, 0, 2, 0, 0, HFC_IO_MODE_REGIO, 0}, 5297 /*9*/ {VENDOR_CCD, "HFC-4S Swyx 4xS0 SX2 QuadBri", 4, 4, 1, 2, 0, 0, 0, 0}, 5298 /*10*/ {VENDOR_JH, "HFC-4S (junghanns 2.0)", 4, 4, 1, 2, 0, 0, 0, 0}, 5299 /*11*/ {VENDOR_PRIM, "HFC-2S Primux Card", 4, 2, 0, 0, 0, 0, 0, 0}, 5300 5301 /*12*/ {VENDOR_BN, "HFC-8S Card", 8, 8, 1, 0, 0, 0, 0, 0}, 5302 /*13*/ {VENDOR_BN, "HFC-8S Card (+)", 8, 8, 1, 8, 0, DIP_8S, 5303 HFC_IO_MODE_REGIO, 0}, 5304 /*14*/ {VENDOR_CCD, "HFC-8S Eval (old)", 8, 8, 0, 0, 0, 0, 0, 0}, 5305 /*15*/ {VENDOR_CCD, "HFC-8S IOB4ST Recording", 8, 8, 1, 0, 0, 0, 0, 0}, 5306 5307 /*16*/ {VENDOR_CCD, "HFC-8S IOB8ST", 8, 8, 1, 0, 0, 0, 0, 0}, 5308 /*17*/ {VENDOR_CCD, "HFC-8S", 8, 8, 1, 0, 0, 0, 0, 0}, 5309 /*18*/ {VENDOR_CCD, "HFC-8S", 8, 8, 1, 0, 0, 0, 0, 0}, 5310 5311 /*19*/ {VENDOR_BN, "HFC-E1 Card", 1, 1, 0, 1, 0, DIP_E1, 0, 0}, 5312 /*20*/ {VENDOR_BN, "HFC-E1 Card (mini PCI)", 1, 1, 0, 1, 0, 0, 0, 0}, 5313 /*21*/ {VENDOR_BN, "HFC-E1+ Card (Dual)", 1, 1, 0, 1, 0, DIP_E1, 0, 0}, 5314 /*22*/ {VENDOR_BN, "HFC-E1 Card (Dual)", 1, 1, 0, 1, 0, DIP_E1, 0, 0}, 5315 5316 /*23*/ {VENDOR_CCD, "HFC-E1 Eval (old)", 1, 1, 0, 0, 0, 0, 0, 0}, 5317 /*24*/ {VENDOR_CCD, "HFC-E1 IOB1E1", 1, 1, 0, 1, 0, 0, 0, 0}, 5318 /*25*/ {VENDOR_CCD, "HFC-E1", 1, 1, 0, 1, 0, 0, 0, 0}, 5319 5320 /*26*/ {VENDOR_CCD, "HFC-4S Speech Design", 4, 4, 0, 0, 0, 0, 5321 HFC_IO_MODE_PLXSD, 0}, 5322 /*27*/ {VENDOR_CCD, "HFC-E1 Speech Design", 1, 1, 0, 0, 0, 0, 5323 HFC_IO_MODE_PLXSD, 0}, 5324 /*28*/ {VENDOR_CCD, "HFC-4S OpenVox", 4, 4, 1, 0, 0, 0, 0, 0}, 5325 /*29*/ {VENDOR_CCD, "HFC-2S OpenVox", 4, 2, 1, 0, 0, 0, 0, 0}, 5326 /*30*/ {VENDOR_CCD, "HFC-8S OpenVox", 8, 8, 1, 0, 0, 0, 0, 0}, 5327 /*31*/ {VENDOR_CCD, "XHFC-4S Speech Design", 5, 4, 0, 0, 0, 0, 5328 HFC_IO_MODE_EMBSD, XHFC_IRQ}, 5329 /*32*/ {VENDOR_JH, "HFC-8S (junghanns)", 8, 8, 1, 0, 0, 0, 0, 0}, 5330 /*33*/ {VENDOR_BN, "HFC-2S Beronet Card PCIe", 4, 2, 1, 3, 0, DIP_4S, 0, 0}, 5331 /*34*/ {VENDOR_BN, "HFC-4S Beronet Card PCIe", 4, 4, 1, 2, 0, DIP_4S, 0, 0}, 5332 }; 5333 5334 #undef H 5335 #define H(x) ((unsigned long)&hfcm_map[x]) 5336 static const struct pci_device_id hfmultipci_ids[] = { 5337 5338 /* Cards with HFC-4S Chip */ 5339 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5340 PCI_SUBDEVICE_ID_CCD_BN1SM, 0, 0, H(0)}, /* BN1S mini PCI */ 5341 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5342 PCI_SUBDEVICE_ID_CCD_BN2S, 0, 0, H(1)}, /* BN2S */ 5343 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5344 PCI_SUBDEVICE_ID_CCD_BN2SM, 0, 0, H(2)}, /* BN2S mini PCI */ 5345 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5346 PCI_SUBDEVICE_ID_CCD_BN4S, 0, 0, H(3)}, /* BN4S */ 5347 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5348 PCI_SUBDEVICE_ID_CCD_BN4SM, 0, 0, H(4)}, /* BN4S mini PCI */ 5349 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5350 PCI_DEVICE_ID_CCD_HFC4S, 0, 0, H(5)}, /* Old Eval */ 5351 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5352 PCI_SUBDEVICE_ID_CCD_IOB4ST, 0, 0, H(6)}, /* IOB4ST */ 5353 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5354 PCI_SUBDEVICE_ID_CCD_HFC4S, 0, 0, H(7)}, /* 4S */ 5355 { PCI_VENDOR_ID_DIGIUM, PCI_DEVICE_ID_DIGIUM_HFC4S, 5356 PCI_VENDOR_ID_DIGIUM, PCI_DEVICE_ID_DIGIUM_HFC4S, 0, 0, H(8)}, 5357 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5358 PCI_SUBDEVICE_ID_CCD_SWYX4S, 0, 0, H(9)}, /* 4S Swyx */ 5359 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5360 PCI_SUBDEVICE_ID_CCD_JH4S20, 0, 0, H(10)}, 5361 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5362 PCI_SUBDEVICE_ID_CCD_PMX2S, 0, 0, H(11)}, /* Primux */ 5363 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5364 PCI_SUBDEVICE_ID_CCD_OV4S, 0, 0, H(28)}, /* OpenVox 4 */ 5365 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5366 PCI_SUBDEVICE_ID_CCD_OV2S, 0, 0, H(29)}, /* OpenVox 2 */ 5367 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5368 0xb761, 0, 0, H(33)}, /* BN2S PCIe */ 5369 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD, 5370 0xb762, 0, 0, H(34)}, /* BN4S PCIe */ 5371 5372 /* Cards with HFC-8S Chip */ 5373 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD, 5374 PCI_SUBDEVICE_ID_CCD_BN8S, 0, 0, H(12)}, /* BN8S */ 5375 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD, 5376 PCI_SUBDEVICE_ID_CCD_BN8SP, 0, 0, H(13)}, /* BN8S+ */ 5377 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD, 5378 PCI_DEVICE_ID_CCD_HFC8S, 0, 0, H(14)}, /* old Eval */ 5379 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD, 5380 PCI_SUBDEVICE_ID_CCD_IOB8STR, 0, 0, H(15)}, /* IOB8ST Recording */ 5381 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD, 5382 PCI_SUBDEVICE_ID_CCD_IOB8ST, 0, 0, H(16)}, /* IOB8ST */ 5383 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD, 5384 PCI_SUBDEVICE_ID_CCD_IOB8ST_1, 0, 0, H(17)}, /* IOB8ST */ 5385 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD, 5386 PCI_SUBDEVICE_ID_CCD_HFC8S, 0, 0, H(18)}, /* 8S */ 5387 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD, 5388 PCI_SUBDEVICE_ID_CCD_OV8S, 0, 0, H(30)}, /* OpenVox 8 */ 5389 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD, 5390 PCI_SUBDEVICE_ID_CCD_JH8S, 0, 0, H(32)}, /* Junganns 8S */ 5391 5392 5393 /* Cards with HFC-E1 Chip */ 5394 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD, 5395 PCI_SUBDEVICE_ID_CCD_BNE1, 0, 0, H(19)}, /* BNE1 */ 5396 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD, 5397 PCI_SUBDEVICE_ID_CCD_BNE1M, 0, 0, H(20)}, /* BNE1 mini PCI */ 5398 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD, 5399 PCI_SUBDEVICE_ID_CCD_BNE1DP, 0, 0, H(21)}, /* BNE1 + (Dual) */ 5400 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD, 5401 PCI_SUBDEVICE_ID_CCD_BNE1D, 0, 0, H(22)}, /* BNE1 (Dual) */ 5402 5403 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD, 5404 PCI_DEVICE_ID_CCD_HFCE1, 0, 0, H(23)}, /* Old Eval */ 5405 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD, 5406 PCI_SUBDEVICE_ID_CCD_IOB1E1, 0, 0, H(24)}, /* IOB1E1 */ 5407 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD, 5408 PCI_SUBDEVICE_ID_CCD_HFCE1, 0, 0, H(25)}, /* E1 */ 5409 5410 { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_CCD, 5411 PCI_SUBDEVICE_ID_CCD_SPD4S, 0, 0, H(26)}, /* PLX PCI Bridge */ 5412 { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_CCD, 5413 PCI_SUBDEVICE_ID_CCD_SPDE1, 0, 0, H(27)}, /* PLX PCI Bridge */ 5414 5415 { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD, 5416 PCI_SUBDEVICE_ID_CCD_JHSE1, 0, 0, H(25)}, /* Junghanns E1 */ 5417 5418 { PCI_VDEVICE(CCD, PCI_DEVICE_ID_CCD_HFC4S), 0 }, 5419 { PCI_VDEVICE(CCD, PCI_DEVICE_ID_CCD_HFC8S), 0 }, 5420 { PCI_VDEVICE(CCD, PCI_DEVICE_ID_CCD_HFCE1), 0 }, 5421 {0, } 5422 }; 5423 #undef H 5424 5425 MODULE_DEVICE_TABLE(pci, hfmultipci_ids); 5426 5427 static int 5428 hfcmulti_probe(struct pci_dev *pdev, const struct pci_device_id *ent) 5429 { 5430 struct hm_map *m = (struct hm_map *)ent->driver_data; 5431 int ret; 5432 5433 if (m == NULL && ent->vendor == PCI_VENDOR_ID_CCD && ( 5434 ent->device == PCI_DEVICE_ID_CCD_HFC4S || 5435 ent->device == PCI_DEVICE_ID_CCD_HFC8S || 5436 ent->device == PCI_DEVICE_ID_CCD_HFCE1)) { 5437 printk(KERN_ERR 5438 "Unknown HFC multiport controller (vendor:%04x device:%04x " 5439 "subvendor:%04x subdevice:%04x)\n", pdev->vendor, 5440 pdev->device, pdev->subsystem_vendor, 5441 pdev->subsystem_device); 5442 printk(KERN_ERR 5443 "Please contact the driver maintainer for support.\n"); 5444 return -ENODEV; 5445 } 5446 ret = hfcmulti_init(m, pdev, ent); 5447 if (ret) 5448 return ret; 5449 HFC_cnt++; 5450 printk(KERN_INFO "%d devices registered\n", HFC_cnt); 5451 return 0; 5452 } 5453 5454 static struct pci_driver hfcmultipci_driver = { 5455 .name = "hfc_multi", 5456 .probe = hfcmulti_probe, 5457 .remove = hfc_remove_pci, 5458 .id_table = hfmultipci_ids, 5459 }; 5460 5461 static void __exit 5462 HFCmulti_cleanup(void) 5463 { 5464 struct hfc_multi *card, *next; 5465 5466 /* get rid of all devices of this driver */ 5467 list_for_each_entry_safe(card, next, &HFClist, list) 5468 release_card(card); 5469 pci_unregister_driver(&hfcmultipci_driver); 5470 } 5471 5472 static int __init 5473 HFCmulti_init(void) 5474 { 5475 int err; 5476 int i, xhfc = 0; 5477 struct hm_map m; 5478 5479 printk(KERN_INFO "mISDN: HFC-multi driver %s\n", HFC_MULTI_VERSION); 5480 5481 #ifdef IRQ_DEBUG 5482 printk(KERN_DEBUG "%s: IRQ_DEBUG IS ENABLED!\n", __func__); 5483 #endif 5484 5485 spin_lock_init(&HFClock); 5486 spin_lock_init(&plx_lock); 5487 5488 if (debug & DEBUG_HFCMULTI_INIT) 5489 printk(KERN_DEBUG "%s: init entered\n", __func__); 5490 5491 switch (poll) { 5492 case 0: 5493 poll_timer = 6; 5494 poll = 128; 5495 break; 5496 case 8: 5497 poll_timer = 2; 5498 break; 5499 case 16: 5500 poll_timer = 3; 5501 break; 5502 case 32: 5503 poll_timer = 4; 5504 break; 5505 case 64: 5506 poll_timer = 5; 5507 break; 5508 case 128: 5509 poll_timer = 6; 5510 break; 5511 case 256: 5512 poll_timer = 7; 5513 break; 5514 default: 5515 printk(KERN_ERR 5516 "%s: Wrong poll value (%d).\n", __func__, poll); 5517 err = -EINVAL; 5518 return err; 5519 5520 } 5521 5522 if (!clock) 5523 clock = 1; 5524 5525 /* Register the embedded devices. 5526 * This should be done before the PCI cards registration */ 5527 switch (hwid) { 5528 case HWID_MINIP4: 5529 xhfc = 1; 5530 m = hfcm_map[31]; 5531 break; 5532 case HWID_MINIP8: 5533 xhfc = 2; 5534 m = hfcm_map[31]; 5535 break; 5536 case HWID_MINIP16: 5537 xhfc = 4; 5538 m = hfcm_map[31]; 5539 break; 5540 default: 5541 xhfc = 0; 5542 } 5543 5544 for (i = 0; i < xhfc; ++i) { 5545 err = hfcmulti_init(&m, NULL, NULL); 5546 if (err) { 5547 printk(KERN_ERR "error registering embedded driver: " 5548 "%x\n", err); 5549 return err; 5550 } 5551 HFC_cnt++; 5552 printk(KERN_INFO "%d devices registered\n", HFC_cnt); 5553 } 5554 5555 /* Register the PCI cards */ 5556 err = pci_register_driver(&hfcmultipci_driver); 5557 if (err < 0) { 5558 printk(KERN_ERR "error registering pci driver: %x\n", err); 5559 return err; 5560 } 5561 5562 return 0; 5563 } 5564 5565 5566 module_init(HFCmulti_init); 5567 module_exit(HFCmulti_cleanup); 5568