1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3  *  Driver for Goodix Touchscreens
4  *
5  *  Copyright (c) 2014 Red Hat Inc.
6  *  Copyright (c) 2015 K. Merker <merker@debian.org>
7  *
8  *  This code is based on gt9xx.c authored by andrew@goodix.com:
9  *
10  *  2010 - 2012 Goodix Technology.
11  */
12 
13 
14 #include <linux/kernel.h>
15 #include <linux/dmi.h>
16 #include <linux/firmware.h>
17 #include <linux/module.h>
18 #include <linux/delay.h>
19 #include <linux/irq.h>
20 #include <linux/interrupt.h>
21 #include <linux/platform_data/x86/soc.h>
22 #include <linux/slab.h>
23 #include <linux/acpi.h>
24 #include <linux/of.h>
25 #include <asm/unaligned.h>
26 #include "goodix.h"
27 
28 #define GOODIX_GPIO_INT_NAME		"irq"
29 #define GOODIX_GPIO_RST_NAME		"reset"
30 
31 #define GOODIX_MAX_HEIGHT		4096
32 #define GOODIX_MAX_WIDTH		4096
33 #define GOODIX_INT_TRIGGER		1
34 #define GOODIX_CONTACT_SIZE		8
35 #define GOODIX_MAX_CONTACT_SIZE		9
36 #define GOODIX_MAX_CONTACTS		10
37 
38 #define GOODIX_CONFIG_MIN_LENGTH	186
39 #define GOODIX_CONFIG_911_LENGTH	186
40 #define GOODIX_CONFIG_967_LENGTH	228
41 #define GOODIX_CONFIG_GT9X_LENGTH	240
42 
43 #define GOODIX_BUFFER_STATUS_READY	BIT(7)
44 #define GOODIX_HAVE_KEY			BIT(4)
45 #define GOODIX_BUFFER_STATUS_TIMEOUT	20
46 
47 #define RESOLUTION_LOC		1
48 #define MAX_CONTACTS_LOC	5
49 #define TRIGGER_LOC		6
50 
51 /* Our special handling for GPIO accesses through ACPI is x86 specific */
52 #if defined CONFIG_X86 && defined CONFIG_ACPI
53 #define ACPI_GPIO_SUPPORT
54 #endif
55 
56 struct goodix_chip_id {
57 	const char *id;
58 	const struct goodix_chip_data *data;
59 };
60 
61 static int goodix_check_cfg_8(struct goodix_ts_data *ts,
62 			      const u8 *cfg, int len);
63 static int goodix_check_cfg_16(struct goodix_ts_data *ts,
64 			       const u8 *cfg, int len);
65 static void goodix_calc_cfg_checksum_8(struct goodix_ts_data *ts);
66 static void goodix_calc_cfg_checksum_16(struct goodix_ts_data *ts);
67 
68 static const struct goodix_chip_data gt1x_chip_data = {
69 	.config_addr		= GOODIX_GT1X_REG_CONFIG_DATA,
70 	.config_len		= GOODIX_CONFIG_GT9X_LENGTH,
71 	.check_config		= goodix_check_cfg_16,
72 	.calc_config_checksum	= goodix_calc_cfg_checksum_16,
73 };
74 
75 static const struct goodix_chip_data gt911_chip_data = {
76 	.config_addr		= GOODIX_GT9X_REG_CONFIG_DATA,
77 	.config_len		= GOODIX_CONFIG_911_LENGTH,
78 	.check_config		= goodix_check_cfg_8,
79 	.calc_config_checksum	= goodix_calc_cfg_checksum_8,
80 };
81 
82 static const struct goodix_chip_data gt967_chip_data = {
83 	.config_addr		= GOODIX_GT9X_REG_CONFIG_DATA,
84 	.config_len		= GOODIX_CONFIG_967_LENGTH,
85 	.check_config		= goodix_check_cfg_8,
86 	.calc_config_checksum	= goodix_calc_cfg_checksum_8,
87 };
88 
89 static const struct goodix_chip_data gt9x_chip_data = {
90 	.config_addr		= GOODIX_GT9X_REG_CONFIG_DATA,
91 	.config_len		= GOODIX_CONFIG_GT9X_LENGTH,
92 	.check_config		= goodix_check_cfg_8,
93 	.calc_config_checksum	= goodix_calc_cfg_checksum_8,
94 };
95 
96 static const struct goodix_chip_id goodix_chip_ids[] = {
97 	{ .id = "1151", .data = &gt1x_chip_data },
98 	{ .id = "1158", .data = &gt1x_chip_data },
99 	{ .id = "5663", .data = &gt1x_chip_data },
100 	{ .id = "5688", .data = &gt1x_chip_data },
101 	{ .id = "917S", .data = &gt1x_chip_data },
102 	{ .id = "9286", .data = &gt1x_chip_data },
103 
104 	{ .id = "911", .data = &gt911_chip_data },
105 	{ .id = "9271", .data = &gt911_chip_data },
106 	{ .id = "9110", .data = &gt911_chip_data },
107 	{ .id = "9111", .data = &gt911_chip_data },
108 	{ .id = "927", .data = &gt911_chip_data },
109 	{ .id = "928", .data = &gt911_chip_data },
110 
111 	{ .id = "912", .data = &gt967_chip_data },
112 	{ .id = "9147", .data = &gt967_chip_data },
113 	{ .id = "967", .data = &gt967_chip_data },
114 	{ }
115 };
116 
117 static const unsigned long goodix_irq_flags[] = {
118 	IRQ_TYPE_EDGE_RISING,
119 	IRQ_TYPE_EDGE_FALLING,
120 	IRQ_TYPE_LEVEL_LOW,
121 	IRQ_TYPE_LEVEL_HIGH,
122 };
123 
124 static const struct dmi_system_id nine_bytes_report[] = {
125 #if defined(CONFIG_DMI) && defined(CONFIG_X86)
126 	{
127 		/* Lenovo Yoga Book X90F / X90L */
128 		.matches = {
129 			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Intel Corporation"),
130 			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "CHERRYVIEW D1 PLATFORM"),
131 			DMI_EXACT_MATCH(DMI_PRODUCT_VERSION, "YETI-11"),
132 		}
133 	},
134 	{
135 		/* Lenovo Yoga Book X91F / X91L */
136 		.matches = {
137 			/* Non exact match to match F + L versions */
138 			DMI_MATCH(DMI_PRODUCT_NAME, "Lenovo YB1-X91"),
139 		}
140 	},
141 #endif
142 	{}
143 };
144 
145 /*
146  * Those tablets have their x coordinate inverted
147  */
148 static const struct dmi_system_id inverted_x_screen[] = {
149 #if defined(CONFIG_DMI) && defined(CONFIG_X86)
150 	{
151 		.ident = "Cube I15-TC",
152 		.matches = {
153 			DMI_MATCH(DMI_SYS_VENDOR, "Cube"),
154 			DMI_MATCH(DMI_PRODUCT_NAME, "I15-TC")
155 		},
156 	},
157 #endif
158 	{}
159 };
160 
161 /**
162  * goodix_i2c_read - read data from a register of the i2c slave device.
163  *
164  * @client: i2c device.
165  * @reg: the register to read from.
166  * @buf: raw write data buffer.
167  * @len: length of the buffer to write
168  */
169 int goodix_i2c_read(struct i2c_client *client, u16 reg, u8 *buf, int len)
170 {
171 	struct i2c_msg msgs[2];
172 	__be16 wbuf = cpu_to_be16(reg);
173 	int ret;
174 
175 	msgs[0].flags = 0;
176 	msgs[0].addr  = client->addr;
177 	msgs[0].len   = 2;
178 	msgs[0].buf   = (u8 *)&wbuf;
179 
180 	msgs[1].flags = I2C_M_RD;
181 	msgs[1].addr  = client->addr;
182 	msgs[1].len   = len;
183 	msgs[1].buf   = buf;
184 
185 	ret = i2c_transfer(client->adapter, msgs, 2);
186 	if (ret >= 0)
187 		ret = (ret == ARRAY_SIZE(msgs) ? 0 : -EIO);
188 
189 	if (ret)
190 		dev_err(&client->dev, "Error reading %d bytes from 0x%04x: %d\n",
191 			len, reg, ret);
192 	return ret;
193 }
194 
195 /**
196  * goodix_i2c_write - write data to a register of the i2c slave device.
197  *
198  * @client: i2c device.
199  * @reg: the register to write to.
200  * @buf: raw data buffer to write.
201  * @len: length of the buffer to write
202  */
203 int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf, int len)
204 {
205 	u8 *addr_buf;
206 	struct i2c_msg msg;
207 	int ret;
208 
209 	addr_buf = kmalloc(len + 2, GFP_KERNEL);
210 	if (!addr_buf)
211 		return -ENOMEM;
212 
213 	addr_buf[0] = reg >> 8;
214 	addr_buf[1] = reg & 0xFF;
215 	memcpy(&addr_buf[2], buf, len);
216 
217 	msg.flags = 0;
218 	msg.addr = client->addr;
219 	msg.buf = addr_buf;
220 	msg.len = len + 2;
221 
222 	ret = i2c_transfer(client->adapter, &msg, 1);
223 	if (ret >= 0)
224 		ret = (ret == 1 ? 0 : -EIO);
225 
226 	kfree(addr_buf);
227 
228 	if (ret)
229 		dev_err(&client->dev, "Error writing %d bytes to 0x%04x: %d\n",
230 			len, reg, ret);
231 	return ret;
232 }
233 
234 int goodix_i2c_write_u8(struct i2c_client *client, u16 reg, u8 value)
235 {
236 	return goodix_i2c_write(client, reg, &value, sizeof(value));
237 }
238 
239 static const struct goodix_chip_data *goodix_get_chip_data(const char *id)
240 {
241 	unsigned int i;
242 
243 	for (i = 0; goodix_chip_ids[i].id; i++) {
244 		if (!strcmp(goodix_chip_ids[i].id, id))
245 			return goodix_chip_ids[i].data;
246 	}
247 
248 	return &gt9x_chip_data;
249 }
250 
251 static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
252 {
253 	unsigned long max_timeout;
254 	int touch_num;
255 	int error;
256 	u16 addr = GOODIX_READ_COOR_ADDR;
257 	/*
258 	 * We are going to read 1-byte header,
259 	 * ts->contact_size * max(1, touch_num) bytes of coordinates
260 	 * and 1-byte footer which contains the touch-key code.
261 	 */
262 	const int header_contact_keycode_size = 1 + ts->contact_size + 1;
263 
264 	/*
265 	 * The 'buffer status' bit, which indicates that the data is valid, is
266 	 * not set as soon as the interrupt is raised, but slightly after.
267 	 * This takes around 10 ms to happen, so we poll for 20 ms.
268 	 */
269 	max_timeout = jiffies + msecs_to_jiffies(GOODIX_BUFFER_STATUS_TIMEOUT);
270 	do {
271 		error = goodix_i2c_read(ts->client, addr, data,
272 					header_contact_keycode_size);
273 		if (error)
274 			return error;
275 
276 		if (data[0] & GOODIX_BUFFER_STATUS_READY) {
277 			touch_num = data[0] & 0x0f;
278 			if (touch_num > ts->max_touch_num)
279 				return -EPROTO;
280 
281 			if (touch_num > 1) {
282 				addr += header_contact_keycode_size;
283 				data += header_contact_keycode_size;
284 				error = goodix_i2c_read(ts->client,
285 						addr, data,
286 						ts->contact_size *
287 							(touch_num - 1));
288 				if (error)
289 					return error;
290 			}
291 
292 			return touch_num;
293 		}
294 
295 		if (data[0] == 0 && ts->firmware_name) {
296 			if (goodix_handle_fw_request(ts))
297 				return 0;
298 		}
299 
300 		usleep_range(1000, 2000); /* Poll every 1 - 2 ms */
301 	} while (time_before(jiffies, max_timeout));
302 
303 	/*
304 	 * The Goodix panel will send spurious interrupts after a
305 	 * 'finger up' event, which will always cause a timeout.
306 	 */
307 	return -ENOMSG;
308 }
309 
310 static int goodix_create_pen_input(struct goodix_ts_data *ts)
311 {
312 	struct device *dev = &ts->client->dev;
313 	struct input_dev *input;
314 
315 	input = devm_input_allocate_device(dev);
316 	if (!input)
317 		return -ENOMEM;
318 
319 	input_copy_abs(input, ABS_X, ts->input_dev, ABS_MT_POSITION_X);
320 	input_copy_abs(input, ABS_Y, ts->input_dev, ABS_MT_POSITION_Y);
321 	/*
322 	 * The resolution of these touchscreens is about 10 units/mm, the actual
323 	 * resolution does not matter much since we set INPUT_PROP_DIRECT.
324 	 * Userspace wants something here though, so just set it to 10 units/mm.
325 	 */
326 	input_abs_set_res(input, ABS_X, 10);
327 	input_abs_set_res(input, ABS_Y, 10);
328 	input_set_abs_params(input, ABS_PRESSURE, 0, 255, 0, 0);
329 
330 	input_set_capability(input, EV_KEY, BTN_TOUCH);
331 	input_set_capability(input, EV_KEY, BTN_TOOL_PEN);
332 	input_set_capability(input, EV_KEY, BTN_STYLUS);
333 	input_set_capability(input, EV_KEY, BTN_STYLUS2);
334 	__set_bit(INPUT_PROP_DIRECT, input->propbit);
335 
336 	input->name = "Goodix Active Pen";
337 	input->phys = "input/pen";
338 	input->id.bustype = BUS_I2C;
339 	input->id.vendor = 0x0416;
340 	if (kstrtou16(ts->id, 10, &input->id.product))
341 		input->id.product = 0x1001;
342 	input->id.version = ts->version;
343 
344 	ts->input_pen = input;
345 	return 0;
346 }
347 
348 static void goodix_ts_report_pen_down(struct goodix_ts_data *ts, u8 *data)
349 {
350 	int input_x, input_y, input_w, error;
351 	u8 key_value;
352 
353 	if (!ts->pen_input_registered) {
354 		error = input_register_device(ts->input_pen);
355 		ts->pen_input_registered = (error == 0) ? 1 : error;
356 	}
357 
358 	if (ts->pen_input_registered < 0)
359 		return;
360 
361 	if (ts->contact_size == 9) {
362 		input_x = get_unaligned_le16(&data[4]);
363 		input_y = get_unaligned_le16(&data[6]);
364 		input_w = get_unaligned_le16(&data[8]);
365 	} else {
366 		input_x = get_unaligned_le16(&data[2]);
367 		input_y = get_unaligned_le16(&data[4]);
368 		input_w = get_unaligned_le16(&data[6]);
369 	}
370 
371 	touchscreen_report_pos(ts->input_pen, &ts->prop, input_x, input_y, false);
372 	input_report_abs(ts->input_pen, ABS_PRESSURE, input_w);
373 
374 	input_report_key(ts->input_pen, BTN_TOUCH, 1);
375 	input_report_key(ts->input_pen, BTN_TOOL_PEN, 1);
376 
377 	if (data[0] & GOODIX_HAVE_KEY) {
378 		key_value = data[1 + ts->contact_size];
379 		input_report_key(ts->input_pen, BTN_STYLUS, key_value & 0x10);
380 		input_report_key(ts->input_pen, BTN_STYLUS2, key_value & 0x20);
381 	} else {
382 		input_report_key(ts->input_pen, BTN_STYLUS, 0);
383 		input_report_key(ts->input_pen, BTN_STYLUS2, 0);
384 	}
385 
386 	input_sync(ts->input_pen);
387 }
388 
389 static void goodix_ts_report_pen_up(struct goodix_ts_data *ts)
390 {
391 	if (!ts->input_pen)
392 		return;
393 
394 	input_report_key(ts->input_pen, BTN_TOUCH, 0);
395 	input_report_key(ts->input_pen, BTN_TOOL_PEN, 0);
396 	input_report_key(ts->input_pen, BTN_STYLUS, 0);
397 	input_report_key(ts->input_pen, BTN_STYLUS2, 0);
398 
399 	input_sync(ts->input_pen);
400 }
401 
402 static void goodix_ts_report_touch_8b(struct goodix_ts_data *ts, u8 *coor_data)
403 {
404 	int id = coor_data[0] & 0x0F;
405 	int input_x = get_unaligned_le16(&coor_data[1]);
406 	int input_y = get_unaligned_le16(&coor_data[3]);
407 	int input_w = get_unaligned_le16(&coor_data[5]);
408 
409 	input_mt_slot(ts->input_dev, id);
410 	input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, true);
411 	touchscreen_report_pos(ts->input_dev, &ts->prop,
412 			       input_x, input_y, true);
413 	input_report_abs(ts->input_dev, ABS_MT_TOUCH_MAJOR, input_w);
414 	input_report_abs(ts->input_dev, ABS_MT_WIDTH_MAJOR, input_w);
415 }
416 
417 static void goodix_ts_report_touch_9b(struct goodix_ts_data *ts, u8 *coor_data)
418 {
419 	int id = coor_data[1] & 0x0F;
420 	int input_x = get_unaligned_le16(&coor_data[3]);
421 	int input_y = get_unaligned_le16(&coor_data[5]);
422 	int input_w = get_unaligned_le16(&coor_data[7]);
423 
424 	input_mt_slot(ts->input_dev, id);
425 	input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, true);
426 	touchscreen_report_pos(ts->input_dev, &ts->prop,
427 			       input_x, input_y, true);
428 	input_report_abs(ts->input_dev, ABS_MT_TOUCH_MAJOR, input_w);
429 	input_report_abs(ts->input_dev, ABS_MT_WIDTH_MAJOR, input_w);
430 }
431 
432 static void goodix_ts_release_keys(struct goodix_ts_data *ts)
433 {
434 	int i;
435 
436 	for (i = 0; i < GOODIX_MAX_KEYS; i++)
437 		input_report_key(ts->input_dev, ts->keymap[i], 0);
438 }
439 
440 static void goodix_ts_report_key(struct goodix_ts_data *ts, u8 *data)
441 {
442 	int touch_num;
443 	u8 key_value;
444 	int i;
445 
446 	if (data[0] & GOODIX_HAVE_KEY) {
447 		touch_num = data[0] & 0x0f;
448 		key_value = data[1 + ts->contact_size * touch_num];
449 		for (i = 0; i < GOODIX_MAX_KEYS; i++)
450 			if (key_value & BIT(i))
451 				input_report_key(ts->input_dev,
452 						 ts->keymap[i], 1);
453 	} else {
454 		goodix_ts_release_keys(ts);
455 	}
456 }
457 
458 /**
459  * goodix_process_events - Process incoming events
460  *
461  * @ts: our goodix_ts_data pointer
462  *
463  * Called when the IRQ is triggered. Read the current device state, and push
464  * the input events to the user space.
465  */
466 static void goodix_process_events(struct goodix_ts_data *ts)
467 {
468 	u8  point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
469 	int touch_num;
470 	int i;
471 
472 	touch_num = goodix_ts_read_input_report(ts, point_data);
473 	if (touch_num < 0)
474 		return;
475 
476 	/* The pen being down is always reported as a single touch */
477 	if (touch_num == 1 && (point_data[1] & 0x80)) {
478 		goodix_ts_report_pen_down(ts, point_data);
479 		goodix_ts_release_keys(ts);
480 		goto sync; /* Release any previously registered touches */
481 	} else {
482 		goodix_ts_report_pen_up(ts);
483 	}
484 
485 	goodix_ts_report_key(ts, point_data);
486 
487 	for (i = 0; i < touch_num; i++)
488 		if (ts->contact_size == 9)
489 			goodix_ts_report_touch_9b(ts,
490 				&point_data[1 + ts->contact_size * i]);
491 		else
492 			goodix_ts_report_touch_8b(ts,
493 				&point_data[1 + ts->contact_size * i]);
494 
495 sync:
496 	input_mt_sync_frame(ts->input_dev);
497 	input_sync(ts->input_dev);
498 }
499 
500 /**
501  * goodix_ts_irq_handler - The IRQ handler
502  *
503  * @irq: interrupt number.
504  * @dev_id: private data pointer.
505  */
506 static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
507 {
508 	struct goodix_ts_data *ts = dev_id;
509 
510 	goodix_process_events(ts);
511 	goodix_i2c_write_u8(ts->client, GOODIX_READ_COOR_ADDR, 0);
512 
513 	return IRQ_HANDLED;
514 }
515 
516 static void goodix_free_irq(struct goodix_ts_data *ts)
517 {
518 	devm_free_irq(&ts->client->dev, ts->client->irq, ts);
519 }
520 
521 static int goodix_request_irq(struct goodix_ts_data *ts)
522 {
523 	return devm_request_threaded_irq(&ts->client->dev, ts->client->irq,
524 					 NULL, goodix_ts_irq_handler,
525 					 ts->irq_flags, ts->client->name, ts);
526 }
527 
528 static int goodix_check_cfg_8(struct goodix_ts_data *ts, const u8 *cfg, int len)
529 {
530 	int i, raw_cfg_len = len - 2;
531 	u8 check_sum = 0;
532 
533 	for (i = 0; i < raw_cfg_len; i++)
534 		check_sum += cfg[i];
535 	check_sum = (~check_sum) + 1;
536 	if (check_sum != cfg[raw_cfg_len]) {
537 		dev_err(&ts->client->dev,
538 			"The checksum of the config fw is not correct");
539 		return -EINVAL;
540 	}
541 
542 	if (cfg[raw_cfg_len + 1] != 1) {
543 		dev_err(&ts->client->dev,
544 			"Config fw must have Config_Fresh register set");
545 		return -EINVAL;
546 	}
547 
548 	return 0;
549 }
550 
551 static void goodix_calc_cfg_checksum_8(struct goodix_ts_data *ts)
552 {
553 	int i, raw_cfg_len = ts->chip->config_len - 2;
554 	u8 check_sum = 0;
555 
556 	for (i = 0; i < raw_cfg_len; i++)
557 		check_sum += ts->config[i];
558 	check_sum = (~check_sum) + 1;
559 
560 	ts->config[raw_cfg_len] = check_sum;
561 	ts->config[raw_cfg_len + 1] = 1; /* Set "config_fresh" bit */
562 }
563 
564 static int goodix_check_cfg_16(struct goodix_ts_data *ts, const u8 *cfg,
565 			       int len)
566 {
567 	int i, raw_cfg_len = len - 3;
568 	u16 check_sum = 0;
569 
570 	for (i = 0; i < raw_cfg_len; i += 2)
571 		check_sum += get_unaligned_be16(&cfg[i]);
572 	check_sum = (~check_sum) + 1;
573 	if (check_sum != get_unaligned_be16(&cfg[raw_cfg_len])) {
574 		dev_err(&ts->client->dev,
575 			"The checksum of the config fw is not correct");
576 		return -EINVAL;
577 	}
578 
579 	if (cfg[raw_cfg_len + 2] != 1) {
580 		dev_err(&ts->client->dev,
581 			"Config fw must have Config_Fresh register set");
582 		return -EINVAL;
583 	}
584 
585 	return 0;
586 }
587 
588 static void goodix_calc_cfg_checksum_16(struct goodix_ts_data *ts)
589 {
590 	int i, raw_cfg_len = ts->chip->config_len - 3;
591 	u16 check_sum = 0;
592 
593 	for (i = 0; i < raw_cfg_len; i += 2)
594 		check_sum += get_unaligned_be16(&ts->config[i]);
595 	check_sum = (~check_sum) + 1;
596 
597 	put_unaligned_be16(check_sum, &ts->config[raw_cfg_len]);
598 	ts->config[raw_cfg_len + 2] = 1; /* Set "config_fresh" bit */
599 }
600 
601 /**
602  * goodix_check_cfg - Checks if config fw is valid
603  *
604  * @ts: goodix_ts_data pointer
605  * @cfg: firmware config data
606  * @len: config data length
607  */
608 static int goodix_check_cfg(struct goodix_ts_data *ts, const u8 *cfg, int len)
609 {
610 	if (len < GOODIX_CONFIG_MIN_LENGTH ||
611 	    len > GOODIX_CONFIG_MAX_LENGTH) {
612 		dev_err(&ts->client->dev,
613 			"The length of the config fw is not correct");
614 		return -EINVAL;
615 	}
616 
617 	return ts->chip->check_config(ts, cfg, len);
618 }
619 
620 /**
621  * goodix_send_cfg - Write fw config to device
622  *
623  * @ts: goodix_ts_data pointer
624  * @cfg: config firmware to write to device
625  * @len: config data length
626  */
627 int goodix_send_cfg(struct goodix_ts_data *ts, const u8 *cfg, int len)
628 {
629 	int error;
630 
631 	error = goodix_check_cfg(ts, cfg, len);
632 	if (error)
633 		return error;
634 
635 	error = goodix_i2c_write(ts->client, ts->chip->config_addr, cfg, len);
636 	if (error)
637 		return error;
638 
639 	dev_dbg(&ts->client->dev, "Config sent successfully.");
640 
641 	/* Let the firmware reconfigure itself, so sleep for 10ms */
642 	usleep_range(10000, 11000);
643 
644 	return 0;
645 }
646 
647 #ifdef ACPI_GPIO_SUPPORT
648 static int goodix_pin_acpi_direction_input(struct goodix_ts_data *ts)
649 {
650 	acpi_handle handle = ACPI_HANDLE(&ts->client->dev);
651 	acpi_status status;
652 
653 	status = acpi_evaluate_object(handle, "INTI", NULL, NULL);
654 	return ACPI_SUCCESS(status) ? 0 : -EIO;
655 }
656 
657 static int goodix_pin_acpi_output_method(struct goodix_ts_data *ts, int value)
658 {
659 	acpi_handle handle = ACPI_HANDLE(&ts->client->dev);
660 	acpi_status status;
661 
662 	status = acpi_execute_simple_method(handle, "INTO", value);
663 	return ACPI_SUCCESS(status) ? 0 : -EIO;
664 }
665 #else
666 static int goodix_pin_acpi_direction_input(struct goodix_ts_data *ts)
667 {
668 	dev_err(&ts->client->dev,
669 		"%s called on device without ACPI support\n", __func__);
670 	return -EINVAL;
671 }
672 
673 static int goodix_pin_acpi_output_method(struct goodix_ts_data *ts, int value)
674 {
675 	dev_err(&ts->client->dev,
676 		"%s called on device without ACPI support\n", __func__);
677 	return -EINVAL;
678 }
679 #endif
680 
681 static int goodix_irq_direction_output(struct goodix_ts_data *ts, int value)
682 {
683 	switch (ts->irq_pin_access_method) {
684 	case IRQ_PIN_ACCESS_NONE:
685 		dev_err(&ts->client->dev,
686 			"%s called without an irq_pin_access_method set\n",
687 			__func__);
688 		return -EINVAL;
689 	case IRQ_PIN_ACCESS_GPIO:
690 		return gpiod_direction_output(ts->gpiod_int, value);
691 	case IRQ_PIN_ACCESS_ACPI_GPIO:
692 		/*
693 		 * The IRQ pin triggers on a falling edge, so its gets marked
694 		 * as active-low, use output_raw to avoid the value inversion.
695 		 */
696 		return gpiod_direction_output_raw(ts->gpiod_int, value);
697 	case IRQ_PIN_ACCESS_ACPI_METHOD:
698 		return goodix_pin_acpi_output_method(ts, value);
699 	}
700 
701 	return -EINVAL; /* Never reached */
702 }
703 
704 static int goodix_irq_direction_input(struct goodix_ts_data *ts)
705 {
706 	switch (ts->irq_pin_access_method) {
707 	case IRQ_PIN_ACCESS_NONE:
708 		dev_err(&ts->client->dev,
709 			"%s called without an irq_pin_access_method set\n",
710 			__func__);
711 		return -EINVAL;
712 	case IRQ_PIN_ACCESS_GPIO:
713 		return gpiod_direction_input(ts->gpiod_int);
714 	case IRQ_PIN_ACCESS_ACPI_GPIO:
715 		return gpiod_direction_input(ts->gpiod_int);
716 	case IRQ_PIN_ACCESS_ACPI_METHOD:
717 		return goodix_pin_acpi_direction_input(ts);
718 	}
719 
720 	return -EINVAL; /* Never reached */
721 }
722 
723 int goodix_int_sync(struct goodix_ts_data *ts)
724 {
725 	int error;
726 
727 	error = goodix_irq_direction_output(ts, 0);
728 	if (error)
729 		goto error;
730 
731 	msleep(50);				/* T5: 50ms */
732 
733 	error = goodix_irq_direction_input(ts);
734 	if (error)
735 		goto error;
736 
737 	return 0;
738 
739 error:
740 	dev_err(&ts->client->dev, "Controller irq sync failed.\n");
741 	return error;
742 }
743 
744 /**
745  * goodix_reset_no_int_sync - Reset device, leaving interrupt line in output mode
746  *
747  * @ts: goodix_ts_data pointer
748  */
749 int goodix_reset_no_int_sync(struct goodix_ts_data *ts)
750 {
751 	int error;
752 
753 	/* begin select I2C slave addr */
754 	error = gpiod_direction_output(ts->gpiod_rst, 0);
755 	if (error)
756 		goto error;
757 
758 	msleep(20);				/* T2: > 10ms */
759 
760 	/* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
761 	error = goodix_irq_direction_output(ts, ts->client->addr == 0x14);
762 	if (error)
763 		goto error;
764 
765 	usleep_range(100, 2000);		/* T3: > 100us */
766 
767 	error = gpiod_direction_output(ts->gpiod_rst, 1);
768 	if (error)
769 		goto error;
770 
771 	usleep_range(6000, 10000);		/* T4: > 5ms */
772 
773 	/*
774 	 * Put the reset pin back in to input / high-impedance mode to save
775 	 * power. Only do this in the non ACPI case since some ACPI boards
776 	 * don't have a pull-up, so there the reset pin must stay active-high.
777 	 */
778 	if (ts->irq_pin_access_method == IRQ_PIN_ACCESS_GPIO) {
779 		error = gpiod_direction_input(ts->gpiod_rst);
780 		if (error)
781 			goto error;
782 	}
783 
784 	return 0;
785 
786 error:
787 	dev_err(&ts->client->dev, "Controller reset failed.\n");
788 	return error;
789 }
790 
791 /**
792  * goodix_reset - Reset device during power on
793  *
794  * @ts: goodix_ts_data pointer
795  */
796 static int goodix_reset(struct goodix_ts_data *ts)
797 {
798 	int error;
799 
800 	error = goodix_reset_no_int_sync(ts);
801 	if (error)
802 		return error;
803 
804 	return goodix_int_sync(ts);
805 }
806 
807 #ifdef ACPI_GPIO_SUPPORT
808 static const struct acpi_gpio_params first_gpio = { 0, 0, false };
809 static const struct acpi_gpio_params second_gpio = { 1, 0, false };
810 
811 static const struct acpi_gpio_mapping acpi_goodix_int_first_gpios[] = {
812 	{ GOODIX_GPIO_INT_NAME "-gpios", &first_gpio, 1 },
813 	{ GOODIX_GPIO_RST_NAME "-gpios", &second_gpio, 1 },
814 	{ },
815 };
816 
817 static const struct acpi_gpio_mapping acpi_goodix_int_last_gpios[] = {
818 	{ GOODIX_GPIO_RST_NAME "-gpios", &first_gpio, 1 },
819 	{ GOODIX_GPIO_INT_NAME "-gpios", &second_gpio, 1 },
820 	{ },
821 };
822 
823 static const struct acpi_gpio_mapping acpi_goodix_reset_only_gpios[] = {
824 	{ GOODIX_GPIO_RST_NAME "-gpios", &first_gpio, 1 },
825 	{ },
826 };
827 
828 static int goodix_resource(struct acpi_resource *ares, void *data)
829 {
830 	struct goodix_ts_data *ts = data;
831 	struct device *dev = &ts->client->dev;
832 	struct acpi_resource_gpio *gpio;
833 
834 	if (acpi_gpio_get_irq_resource(ares, &gpio)) {
835 		if (ts->gpio_int_idx == -1) {
836 			ts->gpio_int_idx = ts->gpio_count;
837 		} else {
838 			dev_err(dev, "More then one GpioInt resource, ignoring ACPI GPIO resources\n");
839 			ts->gpio_int_idx = -2;
840 		}
841 		ts->gpio_count++;
842 	} else if (acpi_gpio_get_io_resource(ares, &gpio))
843 		ts->gpio_count++;
844 
845 	return 0;
846 }
847 
848 /*
849  * This function gets called in case we fail to get the irq GPIO directly
850  * because the ACPI tables lack GPIO-name to APCI _CRS index mappings
851  * (no _DSD UUID daffd814-6eba-4d8c-8a91-bc9bbf4aa301 data).
852  * In that case we add our own mapping and then goodix_get_gpio_config()
853  * retries to get the GPIOs based on the added mapping.
854  */
855 static int goodix_add_acpi_gpio_mappings(struct goodix_ts_data *ts)
856 {
857 	const struct acpi_gpio_mapping *gpio_mapping = NULL;
858 	struct device *dev = &ts->client->dev;
859 	LIST_HEAD(resources);
860 	int irq, ret;
861 
862 	ts->gpio_count = 0;
863 	ts->gpio_int_idx = -1;
864 	ret = acpi_dev_get_resources(ACPI_COMPANION(dev), &resources,
865 				     goodix_resource, ts);
866 	if (ret < 0) {
867 		dev_err(dev, "Error getting ACPI resources: %d\n", ret);
868 		return ret;
869 	}
870 
871 	acpi_dev_free_resource_list(&resources);
872 
873 	/*
874 	 * CHT devices should have a GpioInt + a regular GPIO ACPI resource.
875 	 * Some CHT devices have a bug (where the also is bogus Interrupt
876 	 * resource copied from a previous BYT based generation). i2c-core-acpi
877 	 * will use the non-working Interrupt resource, fix this up.
878 	 */
879 	if (soc_intel_is_cht() && ts->gpio_count == 2 && ts->gpio_int_idx != -1) {
880 		irq = acpi_dev_gpio_irq_get(ACPI_COMPANION(dev), 0);
881 		if (irq > 0 && irq != ts->client->irq) {
882 			dev_warn(dev, "Overriding IRQ %d -> %d\n", ts->client->irq, irq);
883 			ts->client->irq = irq;
884 		}
885 	}
886 
887 	/* Some devices with gpio_int_idx 0 list a third unused GPIO */
888 	if ((ts->gpio_count == 2 || ts->gpio_count == 3) && ts->gpio_int_idx == 0) {
889 		ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_GPIO;
890 		gpio_mapping = acpi_goodix_int_first_gpios;
891 	} else if (ts->gpio_count == 2 && ts->gpio_int_idx == 1) {
892 		ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_GPIO;
893 		gpio_mapping = acpi_goodix_int_last_gpios;
894 	} else if (ts->gpio_count == 1 && ts->gpio_int_idx == -1 &&
895 		   acpi_has_method(ACPI_HANDLE(dev), "INTI") &&
896 		   acpi_has_method(ACPI_HANDLE(dev), "INTO")) {
897 		dev_info(dev, "Using ACPI INTI and INTO methods for IRQ pin access\n");
898 		ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_METHOD;
899 		gpio_mapping = acpi_goodix_reset_only_gpios;
900 	} else if (soc_intel_is_byt() && ts->gpio_count == 2 && ts->gpio_int_idx == -1) {
901 		dev_info(dev, "No ACPI GpioInt resource, assuming that the GPIO order is reset, int\n");
902 		ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_GPIO;
903 		gpio_mapping = acpi_goodix_int_last_gpios;
904 	} else if (ts->gpio_count == 1 && ts->gpio_int_idx == 0) {
905 		/*
906 		 * On newer devices there is only 1 GpioInt resource and _PS0
907 		 * does the whole reset sequence for us.
908 		 */
909 		acpi_device_fix_up_power(ACPI_COMPANION(dev));
910 
911 		/*
912 		 * Before the _PS0 call the int GPIO may have been in output
913 		 * mode and the call should have put the int GPIO in input mode,
914 		 * but the GPIO subsys cached state may still think it is
915 		 * in output mode, causing gpiochip_lock_as_irq() failure.
916 		 *
917 		 * Add a mapping for the int GPIO to make the
918 		 * gpiod_int = gpiod_get(..., GPIOD_IN) call succeed,
919 		 * which will explicitly set the direction to input.
920 		 */
921 		ts->irq_pin_access_method = IRQ_PIN_ACCESS_NONE;
922 		gpio_mapping = acpi_goodix_int_first_gpios;
923 	} else {
924 		dev_warn(dev, "Unexpected ACPI resources: gpio_count %d, gpio_int_idx %d\n",
925 			 ts->gpio_count, ts->gpio_int_idx);
926 		/*
927 		 * On some devices _PS0 does a reset for us and
928 		 * sometimes this is necessary for things to work.
929 		 */
930 		acpi_device_fix_up_power(ACPI_COMPANION(dev));
931 		return -EINVAL;
932 	}
933 
934 	/*
935 	 * Normally we put the reset pin in input / high-impedance mode to save
936 	 * power. But some x86/ACPI boards don't have a pull-up, so for the ACPI
937 	 * case, leave the pin as is. This results in the pin not being touched
938 	 * at all on x86/ACPI boards, except when needed for error-recover.
939 	 */
940 	ts->gpiod_rst_flags = GPIOD_ASIS;
941 
942 	return devm_acpi_dev_add_driver_gpios(dev, gpio_mapping);
943 }
944 #else
945 static int goodix_add_acpi_gpio_mappings(struct goodix_ts_data *ts)
946 {
947 	return -EINVAL;
948 }
949 #endif /* CONFIG_X86 && CONFIG_ACPI */
950 
951 /**
952  * goodix_get_gpio_config - Get GPIO config from ACPI/DT
953  *
954  * @ts: goodix_ts_data pointer
955  */
956 static int goodix_get_gpio_config(struct goodix_ts_data *ts)
957 {
958 	struct device *dev;
959 	struct gpio_desc *gpiod;
960 	bool added_acpi_mappings = false;
961 
962 	if (!ts->client)
963 		return -EINVAL;
964 	dev = &ts->client->dev;
965 
966 	/*
967 	 * By default we request the reset pin as input, leaving it in
968 	 * high-impedance when not resetting the controller to save power.
969 	 */
970 	ts->gpiod_rst_flags = GPIOD_IN;
971 
972 	ts->avdd28 = devm_regulator_get(dev, "AVDD28");
973 	if (IS_ERR(ts->avdd28))
974 		return dev_err_probe(dev, PTR_ERR(ts->avdd28), "Failed to get AVDD28 regulator\n");
975 
976 	ts->vddio = devm_regulator_get(dev, "VDDIO");
977 	if (IS_ERR(ts->vddio))
978 		return dev_err_probe(dev, PTR_ERR(ts->vddio), "Failed to get VDDIO regulator\n");
979 
980 retry_get_irq_gpio:
981 	/* Get the interrupt GPIO pin number */
982 	gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
983 	if (IS_ERR(gpiod))
984 		return dev_err_probe(dev, PTR_ERR(gpiod), "Failed to get %s GPIO\n",
985 				     GOODIX_GPIO_INT_NAME);
986 
987 	if (!gpiod && has_acpi_companion(dev) && !added_acpi_mappings) {
988 		added_acpi_mappings = true;
989 		if (goodix_add_acpi_gpio_mappings(ts) == 0)
990 			goto retry_get_irq_gpio;
991 	}
992 
993 	ts->gpiod_int = gpiod;
994 
995 	/* Get the reset line GPIO pin number */
996 	gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_RST_NAME, ts->gpiod_rst_flags);
997 	if (IS_ERR(gpiod))
998 		return dev_err_probe(dev, PTR_ERR(gpiod), "Failed to get %s GPIO\n",
999 				     GOODIX_GPIO_RST_NAME);
1000 
1001 	ts->gpiod_rst = gpiod;
1002 
1003 	switch (ts->irq_pin_access_method) {
1004 	case IRQ_PIN_ACCESS_ACPI_GPIO:
1005 		/*
1006 		 * We end up here if goodix_add_acpi_gpio_mappings() has
1007 		 * called devm_acpi_dev_add_driver_gpios() because the ACPI
1008 		 * tables did not contain name to index mappings.
1009 		 * Check that we successfully got both GPIOs after we've
1010 		 * added our own acpi_gpio_mapping and if we did not get both
1011 		 * GPIOs reset irq_pin_access_method to IRQ_PIN_ACCESS_NONE.
1012 		 */
1013 		if (!ts->gpiod_int || !ts->gpiod_rst)
1014 			ts->irq_pin_access_method = IRQ_PIN_ACCESS_NONE;
1015 		break;
1016 	case IRQ_PIN_ACCESS_ACPI_METHOD:
1017 		if (!ts->gpiod_rst)
1018 			ts->irq_pin_access_method = IRQ_PIN_ACCESS_NONE;
1019 		break;
1020 	default:
1021 		if (ts->gpiod_int && ts->gpiod_rst) {
1022 			ts->reset_controller_at_probe = true;
1023 			ts->load_cfg_from_disk = true;
1024 			ts->irq_pin_access_method = IRQ_PIN_ACCESS_GPIO;
1025 		}
1026 	}
1027 
1028 	return 0;
1029 }
1030 
1031 /**
1032  * goodix_read_config - Read the embedded configuration of the panel
1033  *
1034  * @ts: our goodix_ts_data pointer
1035  *
1036  * Must be called during probe
1037  */
1038 static void goodix_read_config(struct goodix_ts_data *ts)
1039 {
1040 	int x_max, y_max;
1041 	int error;
1042 
1043 	/*
1044 	 * On controllers where we need to upload the firmware
1045 	 * (controllers without flash) ts->config already has the config
1046 	 * at this point and the controller itself does not have it yet!
1047 	 */
1048 	if (!ts->firmware_name) {
1049 		error = goodix_i2c_read(ts->client, ts->chip->config_addr,
1050 					ts->config, ts->chip->config_len);
1051 		if (error) {
1052 			ts->int_trigger_type = GOODIX_INT_TRIGGER;
1053 			ts->max_touch_num = GOODIX_MAX_CONTACTS;
1054 			return;
1055 		}
1056 	}
1057 
1058 	ts->int_trigger_type = ts->config[TRIGGER_LOC] & 0x03;
1059 	ts->max_touch_num = ts->config[MAX_CONTACTS_LOC] & 0x0f;
1060 
1061 	x_max = get_unaligned_le16(&ts->config[RESOLUTION_LOC]);
1062 	y_max = get_unaligned_le16(&ts->config[RESOLUTION_LOC + 2]);
1063 	if (x_max && y_max) {
1064 		input_abs_set_max(ts->input_dev, ABS_MT_POSITION_X, x_max - 1);
1065 		input_abs_set_max(ts->input_dev, ABS_MT_POSITION_Y, y_max - 1);
1066 	}
1067 
1068 	ts->chip->calc_config_checksum(ts);
1069 }
1070 
1071 /**
1072  * goodix_read_version - Read goodix touchscreen version
1073  *
1074  * @ts: our goodix_ts_data pointer
1075  */
1076 static int goodix_read_version(struct goodix_ts_data *ts)
1077 {
1078 	int error;
1079 	u8 buf[6];
1080 	char id_str[GOODIX_ID_MAX_LEN + 1];
1081 
1082 	error = goodix_i2c_read(ts->client, GOODIX_REG_ID, buf, sizeof(buf));
1083 	if (error)
1084 		return error;
1085 
1086 	memcpy(id_str, buf, GOODIX_ID_MAX_LEN);
1087 	id_str[GOODIX_ID_MAX_LEN] = 0;
1088 	strscpy(ts->id, id_str, GOODIX_ID_MAX_LEN + 1);
1089 
1090 	ts->version = get_unaligned_le16(&buf[4]);
1091 
1092 	dev_info(&ts->client->dev, "ID %s, version: %04x\n", ts->id,
1093 		 ts->version);
1094 
1095 	return 0;
1096 }
1097 
1098 /**
1099  * goodix_i2c_test - I2C test function to check if the device answers.
1100  *
1101  * @client: the i2c client
1102  */
1103 static int goodix_i2c_test(struct i2c_client *client)
1104 {
1105 	int retry = 0;
1106 	int error;
1107 	u8 test;
1108 
1109 	while (retry++ < 2) {
1110 		error = goodix_i2c_read(client, GOODIX_REG_ID, &test, 1);
1111 		if (!error)
1112 			return 0;
1113 
1114 		msleep(20);
1115 	}
1116 
1117 	return error;
1118 }
1119 
1120 /**
1121  * goodix_configure_dev - Finish device initialization
1122  *
1123  * @ts: our goodix_ts_data pointer
1124  *
1125  * Must be called from probe to finish initialization of the device.
1126  * Contains the common initialization code for both devices that
1127  * declare gpio pins and devices that do not. It is either called
1128  * directly from probe or from request_firmware_wait callback.
1129  */
1130 static int goodix_configure_dev(struct goodix_ts_data *ts)
1131 {
1132 	int error;
1133 	int i;
1134 
1135 	ts->int_trigger_type = GOODIX_INT_TRIGGER;
1136 	ts->max_touch_num = GOODIX_MAX_CONTACTS;
1137 
1138 	ts->input_dev = devm_input_allocate_device(&ts->client->dev);
1139 	if (!ts->input_dev) {
1140 		dev_err(&ts->client->dev, "Failed to allocate input device.");
1141 		return -ENOMEM;
1142 	}
1143 
1144 	ts->input_dev->name = "Goodix Capacitive TouchScreen";
1145 	ts->input_dev->phys = "input/ts";
1146 	ts->input_dev->id.bustype = BUS_I2C;
1147 	ts->input_dev->id.vendor = 0x0416;
1148 	if (kstrtou16(ts->id, 10, &ts->input_dev->id.product))
1149 		ts->input_dev->id.product = 0x1001;
1150 	ts->input_dev->id.version = ts->version;
1151 
1152 	ts->input_dev->keycode = ts->keymap;
1153 	ts->input_dev->keycodesize = sizeof(ts->keymap[0]);
1154 	ts->input_dev->keycodemax = GOODIX_MAX_KEYS;
1155 
1156 	/* Capacitive Windows/Home button on some devices */
1157 	for (i = 0; i < GOODIX_MAX_KEYS; ++i) {
1158 		if (i == 0)
1159 			ts->keymap[i] = KEY_LEFTMETA;
1160 		else
1161 			ts->keymap[i] = KEY_F1 + (i - 1);
1162 
1163 		input_set_capability(ts->input_dev, EV_KEY, ts->keymap[i]);
1164 	}
1165 
1166 	input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_X);
1167 	input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_Y);
1168 	input_set_abs_params(ts->input_dev, ABS_MT_WIDTH_MAJOR, 0, 255, 0, 0);
1169 	input_set_abs_params(ts->input_dev, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
1170 
1171 retry_read_config:
1172 	/* Read configuration and apply touchscreen parameters */
1173 	goodix_read_config(ts);
1174 
1175 	/* Try overriding touchscreen parameters via device properties */
1176 	touchscreen_parse_properties(ts->input_dev, true, &ts->prop);
1177 
1178 	if (!ts->prop.max_x || !ts->prop.max_y || !ts->max_touch_num) {
1179 		if (!ts->reset_controller_at_probe &&
1180 		    ts->irq_pin_access_method != IRQ_PIN_ACCESS_NONE) {
1181 			dev_info(&ts->client->dev, "Config not set, resetting controller\n");
1182 			/* Retry after a controller reset */
1183 			ts->reset_controller_at_probe = true;
1184 			error = goodix_reset(ts);
1185 			if (error)
1186 				return error;
1187 			goto retry_read_config;
1188 		}
1189 		dev_err(&ts->client->dev,
1190 			"Invalid config (%d, %d, %d), using defaults\n",
1191 			ts->prop.max_x, ts->prop.max_y, ts->max_touch_num);
1192 		ts->prop.max_x = GOODIX_MAX_WIDTH - 1;
1193 		ts->prop.max_y = GOODIX_MAX_HEIGHT - 1;
1194 		ts->max_touch_num = GOODIX_MAX_CONTACTS;
1195 		input_abs_set_max(ts->input_dev,
1196 				  ABS_MT_POSITION_X, ts->prop.max_x);
1197 		input_abs_set_max(ts->input_dev,
1198 				  ABS_MT_POSITION_Y, ts->prop.max_y);
1199 	}
1200 
1201 	if (dmi_check_system(nine_bytes_report)) {
1202 		ts->contact_size = 9;
1203 
1204 		dev_dbg(&ts->client->dev,
1205 			"Non-standard 9-bytes report format quirk\n");
1206 	}
1207 
1208 	if (dmi_check_system(inverted_x_screen)) {
1209 		ts->prop.invert_x = true;
1210 		dev_dbg(&ts->client->dev,
1211 			"Applying 'inverted x screen' quirk\n");
1212 	}
1213 
1214 	error = input_mt_init_slots(ts->input_dev, ts->max_touch_num,
1215 				    INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
1216 	if (error) {
1217 		dev_err(&ts->client->dev,
1218 			"Failed to initialize MT slots: %d", error);
1219 		return error;
1220 	}
1221 
1222 	error = input_register_device(ts->input_dev);
1223 	if (error) {
1224 		dev_err(&ts->client->dev,
1225 			"Failed to register input device: %d", error);
1226 		return error;
1227 	}
1228 
1229 	/*
1230 	 * Create the input_pen device before goodix_request_irq() calls
1231 	 * devm_request_threaded_irq() so that the devm framework frees
1232 	 * it after disabling the irq.
1233 	 * Unfortunately there is no way to detect if the touchscreen has pen
1234 	 * support, so registering the dev is delayed till the first pen event.
1235 	 */
1236 	error = goodix_create_pen_input(ts);
1237 	if (error)
1238 		return error;
1239 
1240 	ts->irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
1241 	error = goodix_request_irq(ts);
1242 	if (error) {
1243 		dev_err(&ts->client->dev, "request IRQ failed: %d\n", error);
1244 		return error;
1245 	}
1246 
1247 	return 0;
1248 }
1249 
1250 /**
1251  * goodix_config_cb - Callback to finish device init
1252  *
1253  * @cfg: firmware config
1254  * @ctx: our goodix_ts_data pointer
1255  *
1256  * request_firmware_wait callback that finishes
1257  * initialization of the device.
1258  */
1259 static void goodix_config_cb(const struct firmware *cfg, void *ctx)
1260 {
1261 	struct goodix_ts_data *ts = ctx;
1262 	int error;
1263 
1264 	if (ts->firmware_name) {
1265 		if (!cfg)
1266 			goto err_release_cfg;
1267 
1268 		error = goodix_check_cfg(ts, cfg->data, cfg->size);
1269 		if (error)
1270 			goto err_release_cfg;
1271 
1272 		memcpy(ts->config, cfg->data, cfg->size);
1273 	} else if (cfg) {
1274 		/* send device configuration to the firmware */
1275 		error = goodix_send_cfg(ts, cfg->data, cfg->size);
1276 		if (error)
1277 			goto err_release_cfg;
1278 	}
1279 
1280 	goodix_configure_dev(ts);
1281 
1282 err_release_cfg:
1283 	release_firmware(cfg);
1284 	complete_all(&ts->firmware_loading_complete);
1285 }
1286 
1287 static void goodix_disable_regulators(void *arg)
1288 {
1289 	struct goodix_ts_data *ts = arg;
1290 
1291 	regulator_disable(ts->vddio);
1292 	regulator_disable(ts->avdd28);
1293 }
1294 
1295 static int goodix_ts_probe(struct i2c_client *client)
1296 {
1297 	struct goodix_ts_data *ts;
1298 	const char *cfg_name;
1299 	int error;
1300 
1301 	dev_dbg(&client->dev, "I2C Address: 0x%02x\n", client->addr);
1302 
1303 	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
1304 		dev_err(&client->dev, "I2C check functionality failed.\n");
1305 		return -ENXIO;
1306 	}
1307 
1308 	ts = devm_kzalloc(&client->dev, sizeof(*ts), GFP_KERNEL);
1309 	if (!ts)
1310 		return -ENOMEM;
1311 
1312 	ts->client = client;
1313 	i2c_set_clientdata(client, ts);
1314 	init_completion(&ts->firmware_loading_complete);
1315 	ts->contact_size = GOODIX_CONTACT_SIZE;
1316 
1317 	error = goodix_get_gpio_config(ts);
1318 	if (error)
1319 		return error;
1320 
1321 	/* power up the controller */
1322 	error = regulator_enable(ts->avdd28);
1323 	if (error) {
1324 		dev_err(&client->dev,
1325 			"Failed to enable AVDD28 regulator: %d\n",
1326 			error);
1327 		return error;
1328 	}
1329 
1330 	error = regulator_enable(ts->vddio);
1331 	if (error) {
1332 		dev_err(&client->dev,
1333 			"Failed to enable VDDIO regulator: %d\n",
1334 			error);
1335 		regulator_disable(ts->avdd28);
1336 		return error;
1337 	}
1338 
1339 	error = devm_add_action_or_reset(&client->dev,
1340 					 goodix_disable_regulators, ts);
1341 	if (error)
1342 		return error;
1343 
1344 reset:
1345 	if (ts->reset_controller_at_probe) {
1346 		/* reset the controller */
1347 		error = goodix_reset(ts);
1348 		if (error)
1349 			return error;
1350 	}
1351 
1352 	error = goodix_i2c_test(client);
1353 	if (error) {
1354 		if (!ts->reset_controller_at_probe &&
1355 		    ts->irq_pin_access_method != IRQ_PIN_ACCESS_NONE) {
1356 			/* Retry after a controller reset */
1357 			ts->reset_controller_at_probe = true;
1358 			goto reset;
1359 		}
1360 		dev_err(&client->dev, "I2C communication failure: %d\n", error);
1361 		return error;
1362 	}
1363 
1364 	error = goodix_firmware_check(ts);
1365 	if (error)
1366 		return error;
1367 
1368 	error = goodix_read_version(ts);
1369 	if (error)
1370 		return error;
1371 
1372 	ts->chip = goodix_get_chip_data(ts->id);
1373 
1374 	if (ts->load_cfg_from_disk) {
1375 		/* update device config */
1376 		error = device_property_read_string(&client->dev,
1377 						    "goodix,config-name",
1378 						    &cfg_name);
1379 		if (!error)
1380 			snprintf(ts->cfg_name, sizeof(ts->cfg_name),
1381 				 "goodix/%s", cfg_name);
1382 		else
1383 			snprintf(ts->cfg_name, sizeof(ts->cfg_name),
1384 				 "goodix_%s_cfg.bin", ts->id);
1385 
1386 		error = request_firmware_nowait(THIS_MODULE, true, ts->cfg_name,
1387 						&client->dev, GFP_KERNEL, ts,
1388 						goodix_config_cb);
1389 		if (error) {
1390 			dev_err(&client->dev,
1391 				"Failed to invoke firmware loader: %d\n",
1392 				error);
1393 			return error;
1394 		}
1395 
1396 		return 0;
1397 	} else {
1398 		error = goodix_configure_dev(ts);
1399 		if (error)
1400 			return error;
1401 	}
1402 
1403 	return 0;
1404 }
1405 
1406 static void goodix_ts_remove(struct i2c_client *client)
1407 {
1408 	struct goodix_ts_data *ts = i2c_get_clientdata(client);
1409 
1410 	if (ts->load_cfg_from_disk)
1411 		wait_for_completion(&ts->firmware_loading_complete);
1412 }
1413 
1414 static int goodix_suspend(struct device *dev)
1415 {
1416 	struct i2c_client *client = to_i2c_client(dev);
1417 	struct goodix_ts_data *ts = i2c_get_clientdata(client);
1418 	int error;
1419 
1420 	if (ts->load_cfg_from_disk)
1421 		wait_for_completion(&ts->firmware_loading_complete);
1422 
1423 	/* We need gpio pins to suspend/resume */
1424 	if (ts->irq_pin_access_method == IRQ_PIN_ACCESS_NONE) {
1425 		disable_irq(client->irq);
1426 		return 0;
1427 	}
1428 
1429 	/* Free IRQ as IRQ pin is used as output in the suspend sequence */
1430 	goodix_free_irq(ts);
1431 
1432 	/* Save reference (calibration) info if necessary */
1433 	goodix_save_bak_ref(ts);
1434 
1435 	/* Output LOW on the INT pin for 5 ms */
1436 	error = goodix_irq_direction_output(ts, 0);
1437 	if (error) {
1438 		goodix_request_irq(ts);
1439 		return error;
1440 	}
1441 
1442 	usleep_range(5000, 6000);
1443 
1444 	error = goodix_i2c_write_u8(ts->client, GOODIX_REG_COMMAND,
1445 				    GOODIX_CMD_SCREEN_OFF);
1446 	if (error) {
1447 		goodix_irq_direction_input(ts);
1448 		goodix_request_irq(ts);
1449 		return -EAGAIN;
1450 	}
1451 
1452 	/*
1453 	 * The datasheet specifies that the interval between sending screen-off
1454 	 * command and wake-up should be longer than 58 ms. To avoid waking up
1455 	 * sooner, delay 58ms here.
1456 	 */
1457 	msleep(58);
1458 	return 0;
1459 }
1460 
1461 static int goodix_resume(struct device *dev)
1462 {
1463 	struct i2c_client *client = to_i2c_client(dev);
1464 	struct goodix_ts_data *ts = i2c_get_clientdata(client);
1465 	u8 config_ver;
1466 	int error;
1467 
1468 	if (ts->irq_pin_access_method == IRQ_PIN_ACCESS_NONE) {
1469 		enable_irq(client->irq);
1470 		return 0;
1471 	}
1472 
1473 	/*
1474 	 * Exit sleep mode by outputting HIGH level to INT pin
1475 	 * for 2ms~5ms.
1476 	 */
1477 	error = goodix_irq_direction_output(ts, 1);
1478 	if (error)
1479 		return error;
1480 
1481 	usleep_range(2000, 5000);
1482 
1483 	error = goodix_int_sync(ts);
1484 	if (error)
1485 		return error;
1486 
1487 	error = goodix_i2c_read(ts->client, ts->chip->config_addr,
1488 				&config_ver, 1);
1489 	if (!error && config_ver != ts->config[0])
1490 		dev_info(dev, "Config version mismatch %d != %d, resetting controller\n",
1491 			 config_ver, ts->config[0]);
1492 
1493 	if (error != 0 || config_ver != ts->config[0]) {
1494 		error = goodix_reset(ts);
1495 		if (error)
1496 			return error;
1497 
1498 		error = goodix_send_cfg(ts, ts->config, ts->chip->config_len);
1499 		if (error)
1500 			return error;
1501 	}
1502 
1503 	error = goodix_request_irq(ts);
1504 	if (error)
1505 		return error;
1506 
1507 	return 0;
1508 }
1509 
1510 static DEFINE_SIMPLE_DEV_PM_OPS(goodix_pm_ops, goodix_suspend, goodix_resume);
1511 
1512 static const struct i2c_device_id goodix_ts_id[] = {
1513 	{ "GDIX1001:00", 0 },
1514 	{ }
1515 };
1516 MODULE_DEVICE_TABLE(i2c, goodix_ts_id);
1517 
1518 #ifdef CONFIG_ACPI
1519 static const struct acpi_device_id goodix_acpi_match[] = {
1520 	{ "GDIX1001", 0 },
1521 	{ "GDIX1002", 0 },
1522 	{ "GDX9110", 0 },
1523 	{ }
1524 };
1525 MODULE_DEVICE_TABLE(acpi, goodix_acpi_match);
1526 #endif
1527 
1528 #ifdef CONFIG_OF
1529 static const struct of_device_id goodix_of_match[] = {
1530 	{ .compatible = "goodix,gt1151" },
1531 	{ .compatible = "goodix,gt1158" },
1532 	{ .compatible = "goodix,gt5663" },
1533 	{ .compatible = "goodix,gt5688" },
1534 	{ .compatible = "goodix,gt911" },
1535 	{ .compatible = "goodix,gt9110" },
1536 	{ .compatible = "goodix,gt912" },
1537 	{ .compatible = "goodix,gt9147" },
1538 	{ .compatible = "goodix,gt917s" },
1539 	{ .compatible = "goodix,gt927" },
1540 	{ .compatible = "goodix,gt9271" },
1541 	{ .compatible = "goodix,gt928" },
1542 	{ .compatible = "goodix,gt9286" },
1543 	{ .compatible = "goodix,gt967" },
1544 	{ }
1545 };
1546 MODULE_DEVICE_TABLE(of, goodix_of_match);
1547 #endif
1548 
1549 static struct i2c_driver goodix_ts_driver = {
1550 	.probe = goodix_ts_probe,
1551 	.remove = goodix_ts_remove,
1552 	.id_table = goodix_ts_id,
1553 	.driver = {
1554 		.name = "Goodix-TS",
1555 		.acpi_match_table = ACPI_PTR(goodix_acpi_match),
1556 		.of_match_table = of_match_ptr(goodix_of_match),
1557 		.pm = pm_sleep_ptr(&goodix_pm_ops),
1558 	},
1559 };
1560 module_i2c_driver(goodix_ts_driver);
1561 
1562 MODULE_AUTHOR("Benjamin Tissoires <benjamin.tissoires@gmail.com>");
1563 MODULE_AUTHOR("Bastien Nocera <hadess@hadess.net>");
1564 MODULE_DESCRIPTION("Goodix touchscreen driver");
1565 MODULE_LICENSE("GPL v2");
1566